I. MULTIPLE CHOICE: Direction: Read the statement carefully. Choose the letter of the correct answer. Write your answer in the space provided. _____1. Which of the following measuring devices is used by electricians to measure value of voltage, current and resistance? a. Volt-Ohmmeter b. Megger c. multi-tester d. Drilling Equipment _____2. Electrical materials in which splices and joints are being made is called ________________. a. Utility box b. Square Box c. Junction box d. Electrical Boxes _____3. Which electrical device is used to control the flow of current in a circuit or even the entire circuit? a. Flush type convenience outlet b. junction box c. Utility box d. switches _____4. Electrical conductors which are single, usually cylindrical, flexible strand or iron rod of metal is called__________. a. Stranded conductor b. Wires c. Cables d. Conductors _____5. Which tool is used to scrape surfaces of conductors and to remove big cables’ insulation? a. Electrician’s Knife b. Wire Stripper c. screwdriver d. Pliers _____6. A pipe bending tool with handles of several sizes and lengths is called _________________. a. Heat gun b. Wire Stripper c. C Clamp d. EMT pipe bender _____7. Which of the following are electrical protective devices which are used to interrupt the flow of current when short circuit or over current occurs? a. Switches b. Fuses and Circuit Breaker c. Fittings d. Load _____8. Which of the following electrical materials commonly used to fit wiring devices during wiring installation? a. Switches b. Fuses and Circuit Breaker c. Fittings d. Load _____9. A machine used to bore holes on thin metals is called _______________________. a. portable electric drill b. portable grinder c. hammer drill d. Fittings _____10. You are going to attach metallic conduit to the junction box. What electrical materials used to attach metallic or non-metallic conduit to the junction or utility boxes? a. clamps b. connectors c. junction box d. conduits _____11. In making extension cord, a flat cord is attached to a device on one end and the other end is connected toa current consuming instrument or appliance. a. male plug b. switch c. receptacle d. cord _____12. You are about to disconnect the flow of electricity in the current. Which device you are going to turn offto disconnect the flow of current? a. convenience outlet b. lamp holder s c. male plug d. switch _____13. When using extension cord with the disc grinder, make sure that the cord is sufficiently large in size for the grinder. What is the preferred size of extension cord for portable grinder? a. # 5.5mm2 b. # 3.5mm2 c. # 2.0mm2 d. # 6.0mm2 _____14. Which of the following is an example of electrical power tools? a. Claw hammer b. Wrenches c. Pliers d. Electric drill _____15. Electrical tools are used to multiply manual work of humans. The following are the advantages of using proper electrical tools, EXCEPT: a. High quality of work is achieved. c. Accuracy is obtained b. Accomplishment of a task is slower. d. Efficiency of the work is met. ____16. Safety is important in working using power tools. The following are the general safety rules in using power equipment, EXCEPT: a. Follow manufacturer’s operating instructions. c. Use eye protection b. Always place hands in a pinch point. d. Wear gloves when working with hot equipment or materials. ____17. The purpose of moving the drill and the bit up and down often while drilling deep holes is to _________. a. Ream the hole slightly larger c. help keep the hole centered b. Give the drill operator better drilling leverage d. reduce overheating in the drill bit ____18. In using portable electric drill, why do we need to turn the drill on before attempting to drill a hole? a. See if the drill operates c. make sure the chuck key has been removed b. See if the drill bit is running true d. check if the power cord is good ____19. Which of the following is used to drive the pressurized oil? a. Pipe bender b. Pipe support c. hydraulic pump d. hydraulic ram ____20. Which device is used to transfer hydraulic pressure to a mechanical device? a. Bender b. support c. pump d. ram ____21. Which of the following hydraulic tools is used for boring holes on metal enclosures? a. Pipe Bender b. Crimper c. Knockout Set d. core drilling machine ____22. Tool used for bending conduit at various angles is ___________________. a. Pipe Bender b. Crimper c. Knockout Set d. core drilling machine _____23. Which of the following tools is used for splicing conductors easily? a. Pipe Bender b. Crimper c. Knockout Set d. core drilling machine ____24. Safety is also important in using hydraulic tools. The following are the safety rules in using hydraulic pipe bender, EXCEPT: a. Substitute brake oil for hydraulic oil c. Never place hands near ram b. Never disconnect the hose when it is under pressure. d. Always use proper size conduit shoe and support. ___25. In bending conduit using hydraulic pipe bender, why is it that we need to make sure the floor area is clear? a. For the pipe to move freely when bending. c. to obtain holes that are placed accurately b. To make sure the pipe will bend. d. to lift heavy parts correctly. ___26. Used to describe the regulated or best practice method use of colors for safety purposes in the workplace is called _________________. a. Safety reminder b. safety color c. safety alarm d. safety handle ___27. Which safety sign used when there is an immediate risk to the life and health of an employee? a. Danger b. warning c. caution d. Safety Alert ___28. Which category is a risk, but it is not as severe or immediate as when danger is used? a. Danger b. warning c. caution d. safety alert ___29. Sign used for alerting people to a potential risk is ____________________. a. Danger b. warning c. caution d. safety alert ___30. Which color is used on any safety signs, labels, or other objects to signify danger or to alert people that they need to stop? a. Blue b. Orange c. Red d. Green ___31. Basic colors are excellent at alerting workers of any dangerous hazards present in the facility. The following are the importance of safety colors in safety signs, EXCEPT: a. assist in enforcing PPE rules c. give employees the information b. prevent unauthorized employees from entering a restricted space d. decreasing awareness ___32. How important are color-coded signs and markings in a workplace? a. Very important because allow people to immediately determine the type of safety hazard in the area b. Important because it attracts the employee c. Not important because it serves as distraction to the employee d. Important because it can help facilities learn how to properly use safety colors ____32. Which of the following is a Japanese term for SORT? a. seiri b. seiton c. seiso d. shitsuke ____33. Which of the following is a Japanese term for sustain or self-disciplne? a. seiri b. seiton c. seiso d. shitsuke ____34. Which of the following is an English term for SEITON? a. systematize b. sort c. sweep d. standardize/sanitize ____35. An English term for SEIKETSU is ________________. a. systematize b. sort c. sweep d. standardize/sanitize ____36. English term for SEISO is ___________________. a. systematize b. sort c. sweep d. standardize/sanitize ____37. The 5s is a reference to a list of five Japanese words translated into English. Which of the following is NOT the benefits of 5s? a. Decides what should be kept c. Adds distraction to a workplace b. Keep the workplace clean d. Keep the workplace organized ____38. Good housekeeping goes hand-in –hand with good public relations. Why is it important to practice good housekeeping? a. To decrease cost of replacement c. To decrease system downtime b. For better spares inventory management d. To identify a safe workplace.