falatghareh.ir
falatghareh.ir
ASME B16.9-2018
(Revision of ASME B16.9-2012)
Factory-Made
Wrought
Buttwelding
Fittings
A N A M E R I C A N N AT I O N A L STA N DA R D
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
(Revision of ASME B16.9-2012)
Factory-Made
Wrought
Buttwelding
Fittings
AN AMERICAN NATIONAL STANDARD
x
falatghareh.ir
falatghareh.ir
Date of Issuance: October 29, 2018
The next edition of this Standard is scheduled for publication in 2023.
ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Periodically certain
actions of the ASME B16 Committee may be published as Cases. Cases and interpretations are published on the ASME website
under the Committee Pages at http://cstools.asme.org/ as they are issued.
Errata to codes and standards may be posted on the ASME website under the Committee Pages to provide corrections to
incorrectly published items, or to correct typographical or grammatical errors in codes and standards. Such errata shall be used
on the date posted.
The Committee Pages can be found at http://cstools.asme.org/. There is an option available to automatically receive an e-mail
notification when errata are posted to a particular code or standard. This option can be found on the appropriate Committee
Page after selecting “Errata” in the “Publication Information” section.
ASME is the registered trademark of The American Society of Mechanical Engineers.
This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards
Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an
opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity
for additional public input from industry, academia, regulatory agencies, and the public-at-large.
ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.
ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this
document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor
assume any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the
risk of infringement of such rights, is entirely their own responsibility.
Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry
endorsement of this code or standard.
ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures
and policies, which precludes the issuance of interpretations by individuals.
No part of this document may be reproduced in any form,
in an electronic retrieval system or otherwise,
without the prior written permission of the publisher.
The American Society of Mechanical Engineers
Two Park Avenue, New York, NY 10016-5990
Copyright © 2018 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All rights reserved
Printed in U.S.A.
falatghareh.ir
falatghareh.ir
CONTENTS
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v
Committee Roster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi
Correspondence With the B16 Committee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vii
Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ix
List of Changes in Record Number Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
x
1
2
3
4
5
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
1
2
2
3
6
7
8
9
10
11
Fitting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Surface Contours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
End Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Design Proof Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Production Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3
3
3
3
5
5
Mandatory Appendix
I
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
Nonmandatory Appendix
A
Quality System Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
Figure
8-1
Maximum Envelope for Welding End Transitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
Tables
5-1
6.1-1
6.1-2
6.1-3
6.1-4
6.1-5
6.1-6
6.1-7
6.1-8
6.1-9
6.1-10
Material Groupings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of Long Radius Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of Long Radius Reducing Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of Long Radius Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of Short Radius Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of Short Radius 180-deg Returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of 3D Radius Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of Straight Tees and Crosses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of Reducing Outlet Tees and Reducing Outlet Crosses . . . . . . . . . . . . . . . . . . . .
Dimensions of Lap Joint Stub Ends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions of Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
7
8
9
9
10
11
12
13
19
20
iii
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
falatghareh.ir
falatghareh.ir
6.1-11
8-1
9.2.1-1
9.3.1-1
11-1
Dimensions of Reducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welding Bevels and Root Face . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Testing Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Factor, f, Determination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tolerances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
21
23
25
25
26
falatghareh.ir
falatghareh.ir
FOREWORD
In 1921, the American Engineering Standards Committee, later the American Standards Association (ASA), organized
Sectional Committee B16 to unify and further develop national standards for pipe flanges and fittings (and later, for
valves, gaskets, and valve actuators). Cosponsors of the B16 Committee were The American Society of Mechanical
Engineers (ASME), the Heating and Piping Contractors National Association [now the Mechanical Contractors
Association of America (MCAA)], and the Manufacturers Standardization Society of the Valve and Fittings Industry
(MSS). Cosponsors were later designated as cosecretariat organizations.
Standardization of welding fittings was initiated in 1937 by a subgroup (designated Subgroup 6) of Subcommittee 3.
After consideration of several drafts, a standard was approved by the Committee, cosponsors, and ASA, and published
with the designation ASA B16.9-1940.
Revisions were made in 1950 and 1955 to add sizes up to NPS 24 and to complete coverage of fittings in some sizes.
These revisions were approved and published as ASA B16.9-1951 and ASA B16.9-1958. With the subgroup now designated Subcommittee 6 (later Subcommittee F), further revisions were begun to clarify the intent of the Standard, to add
angularity tolerances, and to include fittings of different types (long radius reducing elbows and crosses) and smaller sizes
(NPS 1∕4 and NPS 1∕2). This revision was published as ASA B16.9-1964 after ASA approval.
After reorganization of ASA, first as the United States of America Standards Institute (USASI), then as the American
National Standards Institute (ANSI), with the Sectional Committee being redesignated as an American National Standards
Committee, another revision increasing the size range to NPS 48 and revising the text for clarity was approved and
published as ANSI B16.9-1971.
In 1975, Subcommittee F began a major revision to bring the standard up to date with current practice and usage.
Common fractions were expressed as decimals (but without intending higher precision) and metric dimensional equivalents were added. Provisions for step-wise change of radius for NPS 3∕4 long radius elbows and 180-deg returns were
introduced. Following Standards Committee, cosecretariat, and ANSI approval, the revision was published as ANSI B16.91978. It was updated by a corrective addendum, B16.9a-1981, issued in February 1982.
In 1982, American National Standards Committee B16 was reorganized as an ASME Committee operating under
procedures accredited by ANSI. In ASME/ANSI B16.9-1986, the text was revised and inch dimensions were established
as the standard.
In 1991, the Subcommittee reviewed the Standard and made a number of revisions that were included in ASME B16.91993. Dimensions for short pattern lap joints were also added.
In ASME B16.9-2001, short radius elbows and returns were added, which included all dimensions and tolerances of
ASME B16.28-1994. Metric units were provided as an independent but parallel alternative standard to U.S. Customary
units. U.S. Customary units were moved into parentheses or separate tables in Mandatory Appendix I. In addition, a
Quality System Program appendix was added.
In 2003, the Subcommittee reviewed the Standard and made a number of revisions. The scope of the Standard was
changed to permit fabricated lap joint stub ends employing circumferential or intersection welds.
In 2006, the Subcommittee reviewed the Standard and made a number of additions and revisions. Segmental elbow
requirements were added, as were 3D radius elbow dimensions. Reference documents were updated.
In 2012, the Subcommittee reviewed the Standard and made numerous revisions to the design proof test in section 9
and updated the references in Mandatory Appendix II.
This edition adds more specific descriptions of acceptable design methods, revises the requirements for the design
proof test, and updates the references. In addition, the U.S. Customary tables in Mandatory Appendix I have been merged
with the Metric tables and all tables have been redesignated. Following the approval of the ASME B16 Standards
Committee, ANSI approved ASME B16.9-2018 as an American National Standard on September 25, 2018.
v
falatghareh.ir
falatghareh.ir
ASME B16 COMMITTEE
Standardization of Valves, Flanges, Fittings, and Gaskets
(The following is the roster of the Committee at the time of approval of this Standard.)
STANDARDS COMMITTEE OFFICERS
R. M. Bojarczuk, Chair
C. E. Davila, Vice Chair
C. Ramcharran, Secretary
STANDARDS COMMITTEE PERSONNEL
A. Appleton, Alloy Stainless Products Co., Inc.
J. E. Barker, Dezurik Water Controls
K. Barron, Ward Manufacturing
D. C. Bayreuther, Metso Automation, Flow Control Division
W. B. Bedesem, Consultant
R. M. Bojarczuk, Consultant
A. M. Cheta, Qatar Shell GTL
M. A. Clark, Consultant
G. A. Cuccio, Capitol Manufacturing Co.
J. D’Avanzo, Fluoroseal Valves
C. E. Davila, Crane Energy
K. S. Felder, Valero Energy
D. R. Frikken, Becht Engineering Co.
D. Hunt, Jr., Fastenal
G. A. Jolly, Samshin Ltd.
E. J. Lain, Exelon Nuclear
T. A. McMahon, Emerson Process Management
R. C. Merrick, Fluor Enterprises
M. L. Nayyar, NICE
W. H. Patrick, The Dow Chemical Co.
D. Rahoi, CCM 2000
C. Ramcharran, The American Society of Mechanical Engineers
D. F. Reid, VSP Technologies
R. A. Schmidt, Canadoil
J. P. Tucker, Flowserve Corp.
F. R. Volgstadt, Volgstadt & Associates, Inc.
F. Feng, Delegate, China Productivity Center for Machinery
R. W. Barnes, Contributing Member, Anric Enterprises, Inc.
P. V. Craig, Contributing Member, Jomar Group
B. G. Fabian, Contributing Member, Pennsylvania Machine Works
M. Katcher, Contributing Member, Haynes International
A. G. Kireta, Jr., Contributing Member, Copper Development
Association, Inc.
SUBCOMMITTEE F — STEEL THREADED AND WELDING FITTINGS
B. G. Fabian, Chair, Pennsylvania Machine Works
R. A. Schmidt, Vice Chair, Canadoil
E. Lawson, Secretary, The American Society of Mechanical Engineers
J. Oh, Secretary, The American Society of Mechanical Engineers
A. Appleton, Alloy Stainless Products Co., Inc.
G. A. Cuccio, Capitol Manufacturing Co.
J. G. Dominguez, Welding Outlets, Inc.
K. W. Doughty, CB&I Alloy Piping Products
J. P. Ellenberger
D. R. Frikken, Becht Engineering Co.
P. W. Heald, Bonney Forge
D. Hunt, Jr., Fastenal
G. A. Jolly, Samshin Ltd.
F. Kavarana, CBI, Inc.
W. Pritzl, Erne Fittings GmbH
J. P. Tucker, Flowserve Corp.
G. T. Walden, Wolseley
M. M. Zaidi, Jacobs Engineering Group, Inc.
D. J. Lafferty, Alternate, US Drop Forge Co.
vi
falatghareh.ir
falatghareh.ir
CORRESPONDENCE WITH THE B16 COMMITTEE
General. ASME Standards are developed and maintained with the intent to represent the consensus of concerned
interests. As such, users of this Standard may interact with the Committee by requesting interpretations, proposing
revisions or a case, and attending Committee meetings. Correspondence should be addressed to:
Secretary, B16 Standards Committee
The American Society of Mechanical Engineers
Two Park Avenue
New York, NY 10016-5990
http://go.asme.org/Inquiry
Proposing Revisions. Revisions are made periodically to the Standard to incorporate changes that appear necessary
or desirable, as demonstrated by the experience gained from the application of the Standard. Approved revisions will be
published periodically.
The Committee welcomes proposals for revisions to this Standard. Such proposals should be as specific as possible,
citing the paragraph number(s), the proposed wording, and a detailed description of the reasons for the proposal,
including any pertinent documentation.
Proposing a Case. Cases may be issued to provide alternative rules when justified, to permit early implementation of
an approved revision when the need is urgent, or to provide rules not covered by existing provisions. Cases are effective
immediately upon ASME approval and shall be posted on the ASME Committee web page.
Requests for Cases shall provide a Statement of Need and Background Information. The request should identify the
Standard and the paragraph, figure, or table number(s), and be written as a Question and Reply in the same format as
existing Cases. Requests for Cases should also indicate the applicable edition(s) of the Standard to which the proposed
Case applies.
Interpretations. Upon request, the B16 Standards Committee will render an interpretation of any requirement of the
Standard. Interpretations can only be rendered in response to a written request sent to the Secretary of the B16 Standards
Committee.
Requests for interpretation should preferably be submitted through the online Interpretation Submittal Form. The
form is accessible at http://go.asme.org/InterpretationRequest. Upon submittal of the form, the Inquirer will receive an
automatic e-mail confirming receipt.
If the Inquirer is unable to use the online form, he/she may e-mail the request to the Secretary of the B16 Standards
Committee at SecretaryB16@asme.org, or mail it to the above address. The request for an interpretation should be clear
and unambiguous. It is further recommended that the Inquirer submit his/her request in the following format:
Subject:
Edition:
Cite the applicable paragraph number(s) and the topic of the inquiry in one or two words.
Cite the applicable edition of the Standard for which the interpretation is being requested.
Question:
Phrase the question as a request for an interpretation of a specific requirement suitable for
general understanding and use, not as a request for an approval of a proprietary design or
situation. Please provide a condensed and precise question, composed in such a way that a
“yes” or “no” reply is acceptable.
Proposed Reply(ies):
Provide a proposed reply(ies) in the form of “Yes” or “No,” with explanation as needed. If entering
replies to more than one question, please number the questions and replies.
Background Information: Provide the Committee with any background information that will assist the Committee in
understanding the inquiry. The Inquirer may also include any plans or drawings that are
necessary to explain the question; however, they should not contain proprietary names or
information.
Requests that are not in the format described above may be rewritten in the appropriate format by the Committee prior
to being answered, which may inadvertently change the intent of the original request.
vii
falatghareh.ir
falatghareh.ir
Moreover, ASME does not act as a consultant for specific engineering problems or for the general application or
understanding of the Standard requirements. If, based on the inquiry information submitted, it is the opinion of
the Committee that the Inquirer should seek assistance, the inquiry will be returned with the recommendation
that such assistance be obtained.
ASME procedures provide for reconsideration of any interpretation when or if additional information that might affect
an interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME
Committee or Subcommittee. ASME does not “approve,” “certify,” “rate,” or “endorse” any item, construction, proprietary
device, or activity.
Attending Committee Meetings. The B16 Standards Committee regularly holds meetings and/or telephone conferences that are open to the public. Persons wishing to attend any meeting and/or telephone conference should contact the
Secretary of the B16 Standards Committee.
viii
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
SUMMARY OF CHANGES
Following approval by the ASME B16.9 Committee and ASME, and after public review, ASME B16.9-2018 was approved by
the American National Standards Institute on September 29, 2018.
In ASME B16.9-2018, the U.S. Customary tables formerly in Mandatory Appendix I have been merged with the Metric
tables in the main text; the tables have been redesignated, Mandatory Appendix I deleted, and the cross-references
updated accordingly. In addition, this edition includes the following changes identified by a margin note, (18). The
Record Number listed below is explained in more detail in the “List of Changes in Record Number Order” following
this Summary of Changes.
Page
1
1
Location
1.4
1.5.1
2
3
3
2.2
Section 5
6.2.4
3
6
8
Section 9
Table 5-1
Table 6.1-2
10
Table 6.1-5
11
Table 6.1-6
23
Table 8-1
24
28
Figure 8-1
Mandatory Appendix I
Change (Record Number)
First paragraph editorially revised
References to Mandatory Appendix II
editorially revised
Revised in its entirety (17-1543)
Revised (17-1543)
In subpara. (c), “3D” revised to “3D radius”
(17-1543)
Revised in its entirety (17-1543)
Added (17-1543)
Formerly Tables 2 and I-2; illustration
within table revised (17-1543)
Formerly Tables 5 and I-5; General Note
editorially redesignated as Note (1), and
Note reference added to the illustration
Formerly Tables 6 and I-6; in title, “3D”
revised to “3D Radius,” and in 45-deg
elbow entry for NPS 30, “964” mm revised
to “946” mm (17-1543)
Formerly Table 12; Note (2) revised (171543)
Editorially redesignated from Figure 1
Redesignated from Mandatory Appendix II
and updated (17-1543)
ix
falatghareh.ir
falatghareh.ir
LIST OF CHANGES IN RECORD NUMBER ORDER
Record Number
17-1543
Changes
Revised Table 6 title from “3D” to “3D Radius” in the Contents. Revised the Foreword.
Revised section 2.2 in its entirety. Revised section 5. Revised “3D” to “3D radius” in
section 6.2.4. Revised section 9 in its entirety. Replaced the figure in Tables 2 and I-2.
Revised “3D” to “3D Radius” and “964” to “946” in Table 6. Revised the wording of Note
(2) in Table 12. Revised “3D” to “3D Radius” in Table I-6. Made multiple revisions in
Mandatory Appendix II.
x
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
FACTORY-MADE WROUGHT BUTTWELDING FITTINGS
1.5.2 Codes and Regulations. A fitting used under the
jurisdiction of the ASME Boiler and Pressure Vessel Code
(BPVC), the ASME Code for Pressure Piping, or a governmental regulation is subject to any limitation of that code
or regulation. This includes any maximum temperature
limitation or rule governing the use of a material at
low temperature.
1 SCOPE
1.1 General
This Standard covers overall dimensions, tolerances,
ratings, testing, and markings for factory-made
wrought buttwelding fittings in sizes NPS 1∕2 through
NPS 48 (DN 15 through DN 1200).
1.6 Service Conditions
1.2 Special Fittings
Criteria for selection of fitting types and materials
suitable for particular fluid service are not within the
scope of this Standard.
Fittings may be made to special dimensions, sizes,
shapes, and tolerances by agreement between the manufacturer and the purchaser.
1.7 Welding
1.3 Fabricated Fittings
Installation welding requirements are outside the scope
of this Standard.
Fabricated laterals and other fittings employing circumferential or intersection welds are considered pipe fabrication and are not within the scope of this Standard.
Fabricated lap joint stub ends are exempt from the
above restrictions, provided they meet all the requirements of the applicable ASTM material specification
listed in section 5.
ð18Þ
1.8 Quality Systems
Nonmandatory requirements relating to the fitting
manufacturer’s Quality System Program are described
in Nonmandatory Appendix A.
1.4 Relevant Units
1.9 Convention
This Standard states values in both SI (Metric) and U.S.
Customary units. These systems of units are to be
regarded separately as standard. Within the text and
tables, the U.S. Customary units are shown in parentheses.
The values stated in each system are not exact equivalents;
therefore, it is required that each system of units be used
independently of the other. Combining values from the
two systems constitutes nonconformance with the
Standard.
The designation for size is NPS for both Metric- and
Customary-dimensioned fittings. Fitting pressure rating
is associated with the connecting wall thickness of
pipe of equivalent size and material.
For determining conformance with this Standard, the
convention for fixing significant digits where limits
(maximum and minimum values) are specified shall be
as defined in ASTM E29. This requires that an observed
or calculated value be rounded off to the nearest unit in the
last right-hand digit used for expressing the limit. Decimal
values and tolerances do not imply a particular method of
measurement.
1.10 Pressure Rating Designation
Class followed by a dimensionless number is the designation for pressure–temperature ratings. Standardized
designations for flanges per ASME B16.5 referenced in this
Standard are Classes 150, 300, 600, 900, 1500, and 2500.
1.5 References
ð18Þ
2 PRESSURE RATINGS
1.5.1 Referenced Standards. Standards and specifications adopted by reference in this Standard are shown in
Mandatory Appendix I. It is not considered practical to
identify the specific edition of each standard and specification in the individual references. Instead, the specific
edition reference is identified in Mandatory Appendix
I. A product made in conformance with a prior edition
of referenced standards and in all other respects
conforming to this Standard will be considered to be
in conformance.
2.1 Basis of Ratings
The allowable pressure ratings for fittings designed in
accordance with this Standard may be calculated as for
straight seamless pipe of equivalent material (as
shown by comparison of composition and mechanical
properties in the respective material specifications) in
accordance with the rules established in the applicable
sections of ASME B31, Code for Pressure Piping. For
the calculation, applicable data for the pipe size, wall
1
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
thickness, and material that are equivalent to that of the
fitting shall be used. Pipe size, wall thickness (or schedule
number), and material identity on the fittings are in lieu of
pressure rating markings.
ð18Þ
4 MARKING
4.1 Standard Marking
Each fitting shall be permanently marked to show the
following:
(a) manufacturer’s name or trademark
(b) material identification, either the ASTM or ASME
grade designation
(c) schedule number1 or nominal wall thickness in mm
(d) size — the nominal pipe size (NPS) identification
number related to the end connections shall be used
(e) compliance — see para. 4.4 for standard and special
fitting marking
A manufacturer may supplement these mandatory
markings with others, including a DN size designation,
but confusion with the required marking shall be avoided.
2.2 Design of Fittings
2.2.1 Acceptable Design Methods. The design of
fittings shall be established by one of the following
methods:
(a) mathematical analyses contained in nationally
recognized pressure vessel or piping codes (e.g., ASME
B31.3 para. 304.2 for elbows and para. 304.3 for tees).
(b) proof testing in accordance with section 9 of this
Standard.
(c) experimental stress analysis, such as described in
ASME BPVC, Section VIII, Division 2, Annex 5.F with validation of results. Hydrostatic testing can be used to validate experimental results.
(d) detailed stress analysis (e.g., finite element method)
with results evaluated as described in ASME BPVC, Section
VIII, Division 2, Part 5 with validation of results. Strain
measurement, photoelastic testing, or hydrostatic
testing can be used to validate calculated results.
4.2 Exceptions
Where the size of the fitting does not permit complete
marking, the identification marks may be omitted in
reverse of the order presented in para. 4.1.
4.3 Depth of Stamping
2.2.2 Design Thickness. To meet design or manufacturing requirements, it is expected that some portion of
formed fittings may have to be thicker than the pipe wall
with which the fitting is intended to be used. The mathematical analyses, if used, may take into account such
thicker sections.
4.4 Compliance
2.2.3 Records. Copies of English-language records of
the mathematical analysis, the successful proof test, or
both shall be made available to the purchaser or regulatory authority upon request.
4.4.1 Standard Fittings. That the fitting was manufactured in conformance with this Standard, including all
dimensional requirements, is certified by a prefix “WP”
in the material grade designation marking.
3 SIZE
4.4.2 Special Fittings. That the fitting was manufactured in conformance with this Standard, except that
dimensional requirements are as agreed between the
purchaser and the manufacturer, is certified by a supplementary suffix to the material grade designation marking
as follows:
(a) “S58” of ASTM A960 applies for fittings in accordance with ASTM A234, ASTM A403, and ASTM A420.
(b) “S8” applies for fittings in accordance with ASTM
A815.
(c) “SPLD” applies for fittings in accordance with ASTM
B361, ASTM B363, and ASTM B366.
Where steel stamps are used, care shall be taken so that
the marking is not deep enough or sharp enough to cause
cracks or to reduce the wall thickness of the fitting below
the minimum allowed.
NPS, followed by a dimensionless number, is the designation for nominal fitting size. NPS is related to the reference nominal diameter, DN, used in international
standards. The relationship is, typically, as follows:
DN
NPS
15
1
∕2
20
3
∕4
25
1
32
11∕4
40
11∕2
50
2
65
21∕2
80
3
100
4
1
Schedule number is a dimensionless number that is widely used as a
convenient designation for use in ordering pipe and fittings. It is normally
associated with a group of standardized pipe wall thicknesses. Refer to
ASME B36.10M and ASME B36.19M for complete details on pipe schedule
numbers.
NOTE: For NPS > 4, the equivalence is DN = 25 × NPS.
2
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
ð18Þ
Bs = center-to-end dimension for segmented elbow
θ = angle of segmented elbow — 30 deg, 60 deg, 75
deg, etc.
5 MATERIAL
Wrought fittings covered by this Standard shall be in
accordance with ASTM A234, ASTM A403, ASTM A420,
ASTM A815, ASTM B361, ASTM B363, ASTM B366, or
the corresponding specification listed in ASME BPVC,
Section II. The term “wrought” denotes fittings made of
pipe, tubing, plate, or forgings. For purposes of determining proof testing requirements of section 9, the materials are grouped by similar properties as shown in Table
5-1.
Fittings made from block forgings may only be supplied
subject to agreement between the manufacturer and
purchaser. Such fittings need not meet the requirements
of section 7.
When special elbows are intended for field segmenting,
the outside or inside diameter tolerance shall be furnished
throughout the fitting by agreement between the manufacturer and the purchaser. Any mismatch on the outside
or inside diameter needs to be corrected in the field by
grinding, back-welding, or bridging of weld to meet the
applicable piping code requirements. Although the
elbow intended for field segmenting must meet the requirements of this Standard, once the field-segmented
elbow is cut, it is not a B16.9 product.
7 SURFACE CONTOURS
6 FITTING DIMENSIONS
Where adjacent openings in fittings are not in parallel
planes, they shall be joined by a circular arc or radius on
the external surfaces. The arc or radius may be terminated
in tangents. Except as provided for block forgings (see
section 5), the projected profile of external surfaces of
fittings shall not have sharp intersections (corners)
and/or collapsed arcs.
6.1 General
This Standard provides for a fixed position for the
welding ends with reference to either the centerline of
the fittings or the overall dimensions. Dimensional requirements for these fittings are in Tables 6.1-1
through 6.1-11.
6.2 Special Dimensions
8 END PREPARATION
6.2.1 Fatigue Loading. For applications where fatigue
loading is a concern, required minimum dimensions shall
be furnished by the purchaser.
Unless otherwise specified, the details of the welding
end preparation shall be in accordance with Table 8-1.
Transitions from the welding bevel to the outside
surface of the fitting and from the root face to the
inside surface of the fitting lying within the maximum
envelope shown in Figure 8-1 are at the manufacturer’s
option, except as covered in Note (5) of Figure 8-1 or
unless otherwise specifically ordered.
6.2.2 Bore Diameter. Bore diameters away from the
ends are not specified. If special flow path requirements
are needed, the bore dimensions shall be specified by the
purchaser.
6.2.3 Stub Ends. Service conditions and joint construction often dictate stub end length requirements.
Therefore, the purchaser must specify long or short
pattern fitting when ordering. [See General Note (b) in
Table 6.1-9.]
ð18Þ
9 DESIGN PROOF TEST
9.1 Required Tests
Proof tests shall be made as set forth in this Standard
when the manufacturer chooses proof testing to qualify
the fitting design. The pressure design thickness for
critical areas of each type of fitting shall be determined
and recorded. The design thickness for other sizes or wall
thicknesses covered in para. 9.4 shall require a similar
percentage of reinforcement proportional by size or thickness. Critical areas are normally the inner radius of
elbows, the crotch of tees and crosses, the knuckle
radius of caps, and the large ends of reducers. Proof
test shall be based on the computed burst pressure of
the fitting and its connecting piping as defined in para. 9.3.
6.2.4 Segmental Elbows. Factory-made segments of
short radius, long radius, and 3D radius elbows may
be made to meet customer angle requirements. With
the exception of the B dimension, factory-made segments
of elbows shall meet all other requirements of this
Standard. The B dimension for segmented elbows can
be calculated as follows:
For segments of 90-deg elbows
Bs = A × tan( /2)
where
A = dimension A for appropriate 90-deg elbow being
segmented from
(a) Table 6.1-1 for long radius elbow, mm (in.)
(b) Table 6.1-4 for short radius elbow, mm (in.)
(c) Table 6.1-6 for 3D radius elbow, mm (in.)
9.2 Test Assembly
9.2.1 Representative Components. Each fitting type
shall be tested, except that testing of certain types of
fittings can qualify other fittings as described in Table
3
ð18Þ
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
9.2.1-1. Fittings from the same material group that have
the same basic design configuration and method of manufacture shall be selected from production for testing and
shall be identified as to material, grade, and lot, including
heat treatment.
(a) Examples of different basic configurations include
the following:
(1) elbows of different centerline radius (short
versus long versus 3D radius)
(2) tees or crosses formed in full encircling dies
versus cold or hot extrusion using a pad die
(3) concentric versus eccentric shaped reducers
(4) caps of different configurations
(b) Examples of different methods of manufacture
include the following:
(1) mandrel-formed elbows versus elbows welded
from two half-shells versus bent pipe
(2) cold-formed tees or crosses versus extruded tees
versus machined from solid forgings
(3) conical reducers versus bell-shaped (integral
tangents) reducers
(4) caps formed by extruding through a draw ring
versus ends cut off cold-formed tees versus machined
from solids
(5) hot forming versus cold forming or using differential heating
to a set of fittings. For example, testing an NPS 2, NPS 8, and NPS
24 of the same basic design configuration and method of manufacture would qualify for a test factor of 1.0 and would qualify
fittings of that type from NPS 1 to NPS 48 and thickness ranges in
accordance with para. 9.4.2.
9.2.2 Other Components. Straight seamless or welded
pipe whose calculated bursting strength is at least as great
as the proof test pressure as calculated in para. 9.3 shall be
welded to each end of the fitting to be tested. Pipe sections
may have the nominal wall greater than the thickness indicated by the fitting markings. That greater thickness shall
not exceed 1.5 times the fitting markings wall. Any internal
misalignment greater than 1.5 mm (0.06 in.) shall be
reduced by taper boring at a slope not greater than
1:3. Any other unequal wall welding preparation shall
be in accordance with ASME B16.25. Length of pipe
sections for closures shall be as follows:
(a) Minimum length of pipe shall be one pipe O.D. for
NPS 14 (DN 350) and smaller.
(b) Minimum length of pipe shall be one-half pipe O.D.
for NPS greater than 14 (DN 350).
9.3.3 Test Media. The test shall be conducted with
water. Trapped air in the assembly shall be purged
prior to the start of the test.
9.3.2 Computed Test Pressure. The minimum proof
test pressure shall be at least equal to the value computed
by the following equation and rounded to the nearest 0.2
MPa (25 psi):
P=
2Sft
D
where
D =
f =
P =
S =
specified outside diameter of pipe
test factor from Table 9.3.1-1
computed minimum proof test pressure for fitting
actual tensile strength of the test fitting, determined on a specimen representative of the test
fitting, which shall meet the tensile strength requirements of the applicable material of section 5
t = nominal pipe wall thickness of the pipe that the
fitting marking identifies
NOTE: Any dimensionally consistent system of units may be
used.
9.3.4 Application of Test Pressure. A pump with
suitable pressure capacity shall be used to uniformly
increase the test pressure through yield. Any gauges
attached directly to the assembly may be removed and
the pressure again uniformly increased at a suitable
rate until either failure or the required test pressure
has been achieved and held for 180 s. It is acceptable
to increase pressure in the test assembly to accommodate
reductions in test pressure caused by yielding in the test
assembly.
9.3.5 Recording Pressure–Time Readings. Test pressure versus time readings shall be recorded periodically.
This may be achieved through electronic means or instrumentation with appropriate resolution and range that has
been calibrated prior to the test.
9.3 Test Procedure
To qualify a fitting by proof testing, the fitting shall be
tested as described herein and shall withstand the
minimum calculated pressure for at least 180 s (3 min).
9.3.6 Test Temperature. The temperature(s) of the
test fluid and components of the test assembly may
not intentionally be increased or decreased if doing so
would significantly affect a mechanical property or
response of any component of the test assembly while
it is under test.
9.3.1 Number of Tests. At least three specimen tests for
each fitting, joint size, or configuration are recommended.
The test factor, f, is based on the number of specimen tests
performed. The test factor, f, described in Table 9.3.1-1, is
used in the computed proof test pressure equation.
9.3.7 Test Results. The test may be terminated if any
component (e.g., fitting, pipe segment, fabrication weld) of
the test assembly loses containment. The test of the fitting
shall be considered unsuccessful if there is any loss of
NOTE: Tests of geometrically identical fittings of different sizes
and wall thicknesses that have overlapping ranges as described
in para. 9.4 may be combined to establish the test factor applied
4
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
containment from the tested fitting before or during the
time it is to be held at or above the computed pressure. A
proof test is successful only when the fitting being tested
withstands for at least 180 s a continuous proof test pressure of at least the computed minimum (see para. 9.3.2)
without exhibiting loss of containment or evidence of
cracking, fissuring, tearing, etc. in the fitting under test.
Whenever a significant change is made in the geometry
or method of manufacture, the manufacturer shall either
retest the new production or show by analysis that the
change would not affect the results of prior tests.
Examples of changes in geometry that require retests
are a change in starting thickness or revised tooling
configuration.
9.4 Applicability of Test Results
9.6 Proof Test Report
It is not necessary to conduct an individual test of
fittings with all combinations of sizes, wall thicknesses,
and materials. A successful proof test on one representative fitting may qualify others to the extent described in
paras. 9.4.1, 9.4.2, and 9.4.3.
A report of the testing for each joint configuration shall
be prepared and shall include
(a) description of the test, including the number of tests
and f factor used to establish the target proof test
(b) instrumentation and methods of calibration used
(c) material test reports for the assembly’s materials
(fitting, pipe, and end caps, if used)
(d) actual final test pressures achieved for each test
(e) length of time at or above the required test pressure
(see para. 9.3.4)
(f) calculations performed
(g) location of rupture, if any, including a sketch or
photographs of the assembly
(h) pressure design thickness required in critical areas
(i) certification by the manufacturer and by a licensed
Authorized Inspector or other third party having experience in pressure component design and testing
9.4.1 Size Range. One test fitting may be used to qualify
similarly proportioned fittings as defined in para. 9.2.1
with a size range from one-half to twice that for the
tested fitting.
9.4.2 Thickness Range. One test fitting may be used to
qualify similarly proportioned fittings as defined in para.
9.2.1 with t/D ranges from one-half to three times that for
the tested fitting.
9.4.3 Material Grades. The pressure-retaining capacity of a fitting of the same basic design configuration and
method of manufacture made from material in a material
group as listed in Table 5-1 will be directly proportional to
the tensile properties of the materials. Therefore, it is necessary to test only a representative fitting to prove the
design of a fitting for all materials in a group.
10 PRODUCTION TESTS
Hydrostatic testing of wrought fittings is not required
by this Standard. All fittings shall be capable of withstanding, without leakage or impairment of serviceability,
a hydrostatic test pressure required by the applicable
piping code for seamless pipe of material equivalent to
the fitting material, and of the size and wall thickness
the fitting marking identifies.
9.5 Maintenance of Results
The manufacturer shall have a quality control (QC)
program that verifies the manufacturing process and
material used and ensures that the resulting geometry
and design thickness of the fittings or joints manufactured
reasonably conform to the geometries tested. The QC
program shall control the manufacturing drawings and
maintain the QC records showing conformance to
these drawings.
Tests made in accordance with and at the time of
previous editions of this Standard are not intended to
be nullified by the changes made in this edition’s test
procedure and requirements, provided the design criteria
for the type tested can be determined.
11 TOLERANCES
Tolerances for fittings are shown in Table 11-1 and
apply to the nominal dimensions given in Tables 6.1-1
through 6.1-11. Where given in the tables, the
minimum and maximum dimensions are based on
these tolerances. The listings with decimals do not
imply precision measurement, such as use of vernier,
micrometer, or electronic readout equipment.
5
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 5-1 Material Groupings
ð18Þ
Group No.
Material
Standards
1
Carbon and low-alloy steels
ASTM A234/A234M and ASTM A420/A420M
2
Austenitic and duplex stainless steels
ASTM A403/A403M and ASTM A815/A815M
3
Nickel alloys
ASTM B366/B366M
4
Aluminum alloys
ASTM B361
5
Titanium alloys
ASTM B363
6
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-1 Dimensions of Long Radius Elbows
Center-to-End, mm (in.)
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel,
mm (in.)
90-deg Elbows,
A
45-deg Elbows,
B
1
∕2
21.3 (0.84)
38 (1.50)
3
∕4
26.7 (1.05)
38 (1.50)
19 (0.75)
1
33.4 (1.32)
38 (1.50)
22 (0.88)
11∕4
42.2 (1.66)
48 (1.88)
25 (1.00)
11∕2
48.3 (1.90)
57 (2.25)
29 (1.12)
16 (0.62)
2
60.3 (2.38)
76 (3.00)
35 (1.38)
21∕2
73.0 (2.88)
95 (3.75)
44 (1.75)
3
88.9 (3.50)
114 (4.50)
51 (2.00)
31∕2
101.6 (4.00)
133 (5.25)
57 (2.25)
4
114.3 (4.50)
152 (6.00)
64 (2.50)
5
141.3 (5.56)
190 (7.50)
79 (3.12)
6
168.3 (6.62)
229 (9.00)
95 (3.75)
8
219.1 (8.62)
305 (12.00)
127 (5.00)
10
273.0 (10.75)
381 (15.00)
159 (6.25)
12
323.8 (12.75)
457 (18.00)
190 (7.50)
14
355.6 (14.00)
533 (21.00)
222 (8.75)
16
406.4 (16.00)
610 (24.00)
254 (10.00)
18
457.0 (18.00)
686 (27.00)
286 (11.25)
20
508.0 (20.00)
762 (30.00)
318 (12.50)
22
559.0 (22.00)
838 (33.00)
343 (13.50)
24
610.0 (24.00)
914 (36.00)
381 (15.00)
26
660.0 (26.00)
991 (39.00)
406 (16.00)
28
711.0 (28.00)
1 067 (42.00)
438 (17.25)
30
762.0 (30.00)
1 143 (45.00)
470 (18.50)
32
813.0 (32.00)
1 219 (48.00)
502 (19.75)
533 (21.00)
34
864.0 (34.00)
1 295 (51.00)
36
914.0 (36.00)
1 372 (54.00)
565 (22.25)
38
965.0 (38.00)
1 448 (57.00)
600 (23.62)
40
1 016.0 (40.00)
1 524 (60.00)
632 (24.88)
42
1 067.0 (42.00)
1 600 (63.00)
660 (26.00)
44
1 118.0 (44.00)
1 676 (66.00)
695 (27.38)
46
1 168.0 (46.00)
1 753 (69.00)
727 (28.62)
48
1 219.0 (48.00)
1 829 (72.00)
759 (29.88)
7
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-2 Dimensions of Long Radius Reducing Elbows
ð18Þ
Nominal
Pipe
Size
(NPS)
1
Outside Diameter
at Bevel, mm (in.)
Large End
Small End
Centerto-End,
A, mm (in.)
Nominal
Pipe
Size
(NPS)
Outside Diameter
at Bevel, mm (in.)
Large End
Small End
Centerto-End,
A, mm (in.)
2 × 1 ∕2
60.3 (2.38)
48.3 (1.90)
76 (3.00)
10 × 8
273.0 (10.75)
219.1 (8.62)
381 (15.00)
2 × 11∕4
60.3 (2.38)
42.2 (1.66)
76 (3.00)
10 × 6
273.0 (10.75)
168.3 (6.62)
381 (15.00)
2×1
60.3 (2.38)
33.4 (1.32)
76 (3.00)
10 × 5
273.0 (10.75)
141.3 (5.56)
381 (15.00)
21∕2 × 2
73.0 (2.88)
60.3 (2.38)
95 (3.75)
12 × 10
323.8 (12.75)
273.0 (10.75)
457 (18.00)
21∕2 × 11∕2
73.0 (2.88)
48.3 (1.90)
95 (3.75)
12 × 8
323.8 (12.75)
219.1 (8.62)
457 (18.00)
21∕2 × 11∕4
73.0 (2.88)
42.2 (1.66)
95 (3.75)
12 × 6
323.8 (12.75)
168.3 (6.62)
457 (18.00)
3 × 21∕2
88.9 (3.50)
73.0 (2.88)
114 (4.50)
14 × 12
355.6 (14.00)
323.8 (12.75)
533 (21.00)
3×2
88.9 (3.50)
60.3 (2.38)
114 (4.50)
14 × 10
355.6 (14.00)
273.0 (10.75)
533 (21.00)
3 × 11∕2
88.9 (3.50)
48.3 (1.90)
114 (4.50)
14 × 8
355.6 (14.00)
219.1 (8.62)
533 (21.00)
31∕2 × 3
101.6 (4.00)
88.9 (3.50)
133 (5.25)
16 × 14
406.4 (16.00)
355.6 (14.00)
610 (24.00)
31∕2 × 21∕2
101.6 (4.00)
73.0 (2.88)
133 (5.25)
16 × 12
406.4 (16.00)
323.8 (12.75)
610 (24.00)
31∕2 × 2
101.6 (4.00)
60.3 (2.38)
133 (5.25)
16 × 10
406.4 (16.00)
273.0 (10.75)
610 (24.00)
4 × 31∕2
114.3 (4.50)
101.6 (4.00)
152 (6.00)
18 × 16
457.0 (18.00)
406.4 (16.00)
686 (27.00)
4×3
114.3 (4.50)
88.9 (3.50)
152 (6.00)
18 × 14
457.0 (18.00)
355.6 (14.00)
686 (27.00)
4 × 2 ∕2
114.3 (4.50)
73.0 (2.88)
152 (6.00)
18 × 12
457.0 (18.00)
323.8 (12.75)
686 (27.00)
4×2
114.3 (4.50)
60.3 (2.38)
152 (6.00)
18 × 10
457.0 (18.00)
273.0 (10.75)
686 (27.00)
1
5×4
141.3 (5.56)
114.3 (4.50)
190 (7.50)
20 × 18
508.0 (20.00)
457.0 (18.00)
762 (30.00)
5 × 31∕2
141.3 (5.56)
101.6 (4.00)
190 (7.50)
20 × 16
508.0 (20.00)
406.4 (16.00)
762 (30.00)
5×3
141.3 (5.56)
88.9 (3.50)
190 (7.50)
20 × 14
508.0 (20.00)
355.6 (14.00)
762 (30.00)
5 × 21∕2
141.3 (5.56)
73.0 (2.88)
190 (7.50)
20 × 12
508.0 (20.00)
323.8 (12.75)
762 (30.00)
20 × 10
508.0 (20.00)
273.0 (10.75)
762 (30.00)
6×5
168.3 (6.62)
141.3 (5.56)
229 (9.00)
6×4
168.3 (6.62)
114.3 (4.50)
229 (9.00)
24 × 22
610.0 (24.00)
559.0 (22.00)
914 (36.00)
6 × 31∕2
168.3 (6.62)
101.6 (4.00)
229 (9.00)
24 × 20
610.0 (24.00)
508.0 (20.00)
914 (36.00)
6×3
168.3 (6.62)
88.9 (3.50)
229 (9.00)
24 × 18
610.0 (24.00)
457.0 (18.00)
914 (36.00)
24 × 16
610.0 (24.00)
406.4 (16.00)
914 (36.00)
8×6
219.1 (8.62)
168.3 (6.62)
305 (12.00)
24 × 14
610.0 (24.00)
355.6 (14.00)
914 (36.00)
8×5
219.1 (8.62)
141.3 (5.56)
305 (12.00)
24 × 12
610.0 (24.00)
323.8 (12.75)
914 (36.00)
8×4
219.1 (8.62)
114.3 (4.50)
305 (12.00)
…
8
…
…
…
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-3 Dimensions of Long Radius Returns
Nominal
Pipe
Size
(NPS)
Outside
Diameter
at Bevel,
mm (in.)
CentertoCenter,
O, mm (in.)
BacktoFace,
K, mm (in.)
1
∕2
21.3 (0.84)
76 (3.00)
48 (1.88)
3
∕4
26.7 (1.05)
76 (3.00)
51 (2.00)
1
33.4 (1.32)
76 (3.00)
56 (2.19)
1
1 ∕4
42.2 (1.66)
95 (3.75)
70 (2.75)
1
1 ∕2
48.3 (1.90)
114 (4.50)
83 (3.25)
2
60.3 (2.38)
152 (6.00)
106 (4.19)
21∕2
73.0 (2.88)
190 (7.50)
132 (5.19)
3
88.9 (3.50)
229 (9.00)
159 (6.25)
31∕2
101.6 (4.00)
267 (10.50)
184 (7.25)
4
114.3 (4.50)
305 (12.00)
210 (8.25)
5
141.3 (5.56)
381 (15.00)
262 (10.31)
6
168.3 (6.62)
457 (18.00)
313 (12.31)
8
219.1 (8.62)
610 (24.00)
414 (16.31)
10
273.0 (10.75)
762 (30.00)
518 (20.38)
12
323.8 (12.75)
914 (36.00)
619 (24.38)
14
355.6 (14.00)
1 067 (42.00)
711 (28.00)
16
406.4 (16.00)
1 219 (48.00)
813 (32.00)
18
457.0 (18.00)
1 372 (54.00)
914 (36.00)
20
508.0 (20.00)
1 524 (60.00)
1 016 (40.00)
22
559.0 (22.00)
1 676 (66.00)
1 118 (44.00)
24
610.0 (24.00)
1 829 (72.00)
1 219 (48.00)
Table 6.1-4 Dimensions of Short Radius Elbows
NOTES:
(1) See Table 11-1 for tolerance for alignment of ends U.
(2) Dimension A is equal to one-half of dimension O.
9
Nominal
Pipe
Size
(NPS)
Outside
Diameter
at Bevel,
mm (in.)
CentertoEnd,
A, mm (in.)
1
33.4 (1.32)
25 (1.00)
1
1 ∕4
42.2 (1.66)
32 (1.25)
11∕2
48.3 (1.90)
38 (1.50)
2
60.3 (2.38)
51 (2.00)
21∕2
73.0 (2.88)
64 (2.50)
76 (3.00)
3
88.9 (3.50)
31∕2
101.6 (4.00)
89 (3.50)
4
114.3 (4.50)
102 (4.00)
5
141.3 (5.56)
127 (5.00)
6
168.3 (6.62)
152 (6.00)
8
219.1 (8.62)
203 (8.00)
10
273.0 (10.75)
254 (10.00)
12
323.8 (12.75)
305 (12.00)
14
355.6 (14.00)
356 (14.00)
16
406.4 (16.00)
406 (16.00)
18
457.0 (18.00)
457 (18.00)
20
508.0 (20.00)
508 (20.00)
22
559.0 (22.00)
559 (22.00)
24
610.0 (24.00)
610 (24.00)
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-5 Dimensions of Short Radius 180-deg Returns
ð18Þ
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel,
mm (in.)
Center-to-Center,
O, mm (in.)
Back-to-Face,
K, mm (in.)
1
33.4 (1.32)
51 (2.00)
41 (1.62)
11∕4
42.2 (1.66)
64 (2.50)
52 (2.06)
11∕2
48.3 (1.90)
76 (3.00)
62 (2.44)
2
60.3 (2.38)
102 (4.00)
81 (3.19)
21∕2
73.0 (2.88)
127 (5.00)
100 (3.94)
3
88.9 (3.50)
152 (6.00)
121 (4.75)
31∕2
101.6 (4.00)
178 (7.00)
140 (5.50)
4
114.3 (4.50)
203 (8.00)
159 (6.25)
5
141.3 (5.56)
254 (10.00)
197 (7.75)
6
168.3 (6.62)
305 (12.00)
237 (9.31)
8
219.1 (8.62)
406 (16.00)
313 (12.31)
10
273.0 (10.75)
508 (20.00)
391 (15.38)
12
323.8 (12.75)
610 (24.00)
467 (18.38)
14
355.6 (14.00)
711 (28.00)
533 (21.00)
16
406.4 (16.00)
813 (32.00)
610 (24.00)
18
457.0 (18.00)
914 (36.00)
686 (27.00)
20
508.0 (20.00)
1 016 (40.00)
762 (30.00)
22
559.0 (22.00)
1 118 (44.00)
838 (33.00)
24
610.0 (24.00)
1 219 (48.00)
914 (36.00)
NOTE: (1) Dimension A is equal to one-half of dimension O.
10
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-6 Dimensions of 3D Radius Elbows
ð18Þ
Center-to-End, mm (in.)
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel,
mm (in.)
90-deg Elbows,
A
45-deg Elbows,
B
3
∕4
26.7 (1.05)
57 (2.25)
24 (0.94)
1
33.4 (1.32)
76 (3.00)
31 (1.25)
11∕4
42.2 (1.66)
95 (3.75)
39 (1.56)
11∕2
48.3 (1.90)
114 (4.50)
47 (1.88)
2
60.3 (2.38)
152 (6.00)
63 (2.50)
21∕2
73.0 (2.88)
190 (7.50)
79 (3.12)
3
88.9 (3.50)
229 (9.00)
95 (3.75)
31∕2
101.6 (4.00)
267 (10.50)
111 (4.38)
4
114.3 (4.50)
305 (12.00)
127 (5.00)
5
141.3 (5.56)
381 (15.00)
157 (6.19)
6
168.3 (6.62)
457 (18.00)
189 (7.44)
8
219.1 (8.62)
610 (24.00)
252 (9.94)
10
273.0 (10.75)
762 (30.00)
316 (12.44)
12
323.8 (12.75)
914 (36.00)
378 (14.88)
14
355.6 (14.00)
1 067 (42.00)
441 (17.38)
16
406.4 (16.00)
1 219 (48.00)
505 (19.88)
18
457.0 (18.00)
1 372 (54.00)
568 (22.38)
20
508.0 (20.00)
1 524 (60.00)
632 (24.88)
22
559.0 (22.00)
1 676 (66.00)
694 (27.31)
24
610.0 (24.00)
1 829 (72.00)
757 (29.81)
26
660.0 (26.00)
1 981 (78.00)
821 (32.31)
28
711.0 (28.00)
2 134 (84.00)
883 (34.75)
30
762.0 (30.00)
2 286 (90.00)
946 (37.25)
32
813.0 (32.00)
2 438 (96.00)
1 010 (39.75)
34
864.0 (34.00)
2 591 (102.00)
1 073 (42.25)
36
914.0 (36.00)
2 743 (108.00)
1 135 (44.69)
38
965.0 (38.00)
2 896 (114.00)
1 200 (47.25)
40
1 016.0 (40.00)
3 048 (120.00)
1 264 (49.75)
42
1 067.0 (42.00)
3 200 (126.00)
1 326 (52.19)
44
1 118.0 (44.00)
3 353 (132.00)
1 389 (54.69)
46
1 168.0 (46.00)
3 505 (138.00)
1 453 (57.19)
48
1 219.0 (48.00)
3 658 (144.00)
1 516 (59.69)
11
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-7 Dimensions of Straight Tees and Crosses
C
C
C
C
M
M
M
Center-to-End, mm (in.)
Nominal Pipe Size
(NPS)
1
∕2
3
Outside Diameter at Bevel,
mm (in.)
21.3 (0.84)
Run, C
Outlet, M
[Notes (1) and (2)]
25 (1.00)
25 (1.00)
∕4
26.7 (1.05)
29 (1.12)
29 (1.12)
1
33.4 (1.32)
38 (1.50)
38 (1.50)
11∕4
42.2 (1.66)
48 (1.88)
48 (1.88)
11∕2
48.3 (1.90)
57 (2.25)
57 (2.25)
2
60.3 (2.38)
64 (2.50)
64 (2.50)
21∕2
73.0 (2.88)
76 (3.00)
76 (3.00)
3
88.9 (3.50)
86 (3.38)
86 (3.38)
1
3 ∕2
101.6 (4.00)
95 (3.75)
95 (3.75)
4
114.3 (4.50)
105 (4.12)
105 (4.12)
5
141.3 (5.56)
124 (4.88)
124 (4.88)
6
168.3 (6.62)
143 (5.62)
143 (5.62)
8
219.1 (8.62)
178 (7.00)
178 (7.00)
10
273.0 (10.75)
216 (8.50)
216 (8.50)
12
323.8 (12.75)
254 (10.00)
254 (10.00)
279 (11.00)
14
355.6 (14.00)
279 (11.00)
16
406.4 (16.00)
305 (12.00)
305 (12.00)
18
457.0 (18.00)
343 (13.50)
343 (13.50)
20
508.0 (20.00)
381 (15.00)
381 (15.00)
22
559.0 (22.00)
419 (16.50)
419 (16.50)
24
610.0 (24.00)
432 (17.00)
432 (17.00)
495 (19.50)
26
660.0 (26.00)
495 (19.50)
28
711.0 (28.00)
521 (20.50)
521 (20.50)
30
762.0 (30.00)
559 (22.00)
559 (22.00)
32
813.0 (32.00)
597 (23.50)
597 (23.50)
635 (25.00)
34
864.0 (34.00)
635 (25.00)
36
914.0 (36.00)
673 (26.50)
673 (26.50)
38
965.0 (38.00)
711 (28.00)
711 (28.00)
40
1 016.0 (40.00)
749 (29.50)
749 (29.50)
42
1 067.0 (42.00)
762 (30.00)
711 (28.00)
44
1 118.0 (44.00)
813 (32.00)
762 (30.00)
46
1 168.0 (46.00)
851 (33.50)
800 (31.50)
48
1 219.0 (48.00)
889 (35.00)
838 (33.00)
NOTES:
(1) Outlet dimension M for NPS 26 and larger is recommended but not required.
(2) Dimensions applicable to crosses NPS 24 and smaller.
12
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-8 Dimensions of Reducing Outlet Tees and Reducing Outlet Crosses
Nominal Pipe Size
(NPS)
∕2 × 1∕2 × 3∕8
Outside Diameter at Bevel, mm (in.)
Run
Outlet
Center-to-End, mm (in.)
Run, C
Outlet, M [Note (1)]
1
21.3 (0.84)
17.3 (0.68)
25 (1.00)
25 (1.00)
1
21.3 (0.84)
13.7 (0.54)
25 (1.00)
25 (1.00)
3
26.7 (1.05)
21.3 (0.84)
29 (1.12)
29 (1.12)
∕2 × 1∕2 × 1∕4
∕4 × 3∕4 × 1∕2
3
3
3
26.7 (1.05)
17.3 (0.68)
29 (1.12)
29 (1.12)
1 × 1 × 3∕4
∕4 × ∕4 × ∕8
33.4 (1.32)
26.7 (1.05)
38 (1.50)
38 (1.50)
1 × 1 × 1∕2
33.4 (1.32)
21.3 (0.84)
38 (1.50)
38 (1.50)
11∕4 × 11∕4 × 1
42.2 (1.66)
33.4 (1.32)
48 (1.88)
48 (1.88)
11∕4 × 11∕4 × 3∕4
42.2 (1.66)
26.7 (1.05)
48 (1.88)
48 (1.88)
11∕4 × 11∕4 × 1∕2
42.2 (1.66)
21.3 (0.84)
48 (1.88)
48 (1.88)
11∕2 × 11∕2 × 11∕4
48.3 (1.90)
42.2 (1.66)
57 (2.25)
57 (2.25)
1
1
1 ∕2 × 1 ∕2 × 1
48.3 (1.90)
33.4 (1.32)
57 (2.25)
57 (2.25)
11∕2 × 11∕2 × 3∕4
48.3 (1.90)
26.7 (1.05)
57 (2.25)
57 (2.25)
11∕2 × 11∕2 × 1∕2
48.3 (1.90)
21.3 (0.84)
57 (2.25)
57 (2.25)
2 × 2 × 11∕2
60.3 (2.38)
48.3 (1.90)
64 (2.50)
60 (2.38)
2 × 2 × 11∕4
60.3 (2.38)
42.2 (1.66)
64 (2.50)
57 (2.25)
2×2×1
60.3 (2.38)
33.4 (1.32)
64 (2.50)
51 (2.00)
2 × 2 × 3∕4
60.3 (2.38)
26.7 (1.05)
64 (2.50)
44 (1.75)
21∕2 × 21∕2 × 2
73.0 (2.88)
60.3 (2.38)
76 (3.00)
70 (2.75)
21∕2 × 21∕2 × 11∕2
73.0 (2.88)
48.3 (1.90)
76 (3.00)
67 (2.62)
21∕2 × 21∕2 × 11∕4
73.0 (2.88)
42.2 (1.66)
76 (3.00)
64 (2.50)
21∕2 × 21∕2 × 1
73.0 (2.88)
33.4 (1.32)
76 (3.00)
57 (2.25)
3 × 3 × 21∕2
88.9 (3.50)
73.0 (2.88)
86 (3.38)
83 (3.25)
3×3×2
88.9 (3.50)
60.3 (2.38)
86 (3.38)
76 (3.00)
3 × 3 × 11∕2
88.9 (3.50)
48.3 (1.90)
86 (3.38)
73 (2.88)
3 × 3 × 11∕4
88.9 (3.50)
42.2 (1.66)
86 (3.38)
70 (2.75)
31∕2 × 31∕2 × 3
101.6 (4.00)
88.9 (3.50)
95 (3.75)
92 (3.62)
31∕2 × 31∕2 × 21∕2
101.6 (4.00)
73.0 (2.88)
95 (3.75)
89 (3.50)
31∕2 × 31∕2 × 2
101.6 (4.00)
60.3 (2.38)
95 (3.75)
83 (3.25)
31∕2 × 31∕2 × 11∕2
101.6 (4.00)
48.3 (1.90)
95 (3.75)
79 (3.12)
4 × 4 × 31∕2
114.3 (4.50)
101.6 (4.00)
105 (4.12)
102 (4.00)
4×4×3
114.3 (4.50)
88.9 (3.50)
105 (4.12)
98 (3.88)
4 × 4 × 21∕2
114.3 (4.50)
73.0 (2.88)
105 (4.12)
95 (3.75)
4×4×2
114.3 (4.50)
60.3 (2.38)
105 (4.12)
89 (3.50)
4 × 4 × 11∕2
114.3 (4.50)
48.3 (1.90)
105 (4.12)
86 (3.38)
13
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-8 Dimensions of Reducing Outlet Tees and Reducing Outlet Crosses (Cont’d)
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel, mm (in.)
Run
Outlet
Center-to-End, mm (in.)
Run, C
Outlet, M [Note (1)]
5×5×4
141.3 (5.56)
114.3 (4.50)
124 (4.88)
117 (4.62)
5 × 5 × 31∕2
141.3 (5.56)
101.6 (4.00)
124 (4.88)
114 (4.50)
5×5×3
141.3 (5.56)
88.9 (3.50)
124 (4.88)
111 (4.38)
5 × 5 × 21∕2
141.3 (5.56)
73.0 (2.88)
124 (4.88)
108 (4.25)
5×5×2
141.3 (5.56)
60.3 (2.38)
124 (4.88)
105 (4.12)
6×6×5
168.3 (6.62)
141.3 (5.56)
143 (5.62)
137 (5.38)
6×6×4
168.3 (6.62)
114.3 (4.50)
143 (5.62)
130 (5.12)
6 × 6 × 31∕2
168.3 (6.62)
101.6 (4.00)
143 (5.62)
127 (5.00)
6×6×3
168.3 (6.62)
88.9 (3.50)
143 (5.62)
124 (4.88)
6 × 6 × 21∕2
168.3 (6.62)
73.0 (2.88)
143 (5.62)
121 (4.75)
8×8×6
219.1 (8.62)
168.3 (6.62)
178 (7.00)
168 (6.62)
8×8×5
219.1 (8.62)
141.3 (5.56)
178 (7.00)
162 (6.38)
8×8×4
219.1 (8.62)
114.3 (4.50)
178 (7.00)
156 (6.12)
8 × 8 × 31∕2
219.1 (8.62)
101.6 (4.00)
178 (7.00)
152 (6.00)
10 × 10 × 8
273.0 (10.75)
219.1 (8.62)
216 (8.50)
203 (8.00)
10 × 10 × 6
273.0 (10.75)
168.3 (6.62)
216 (8.50)
194 (7.62)
10 × 10 × 5
273.0 (10.75)
141.3 (5.56)
216 (8.50)
191 (7.50)
10 × 10 × 4
273.0 (10.75)
114.3 (4.50)
216 (8.50)
184 (7.25)
12 × 12 × 10
323.8 (12.75)
273.0 (10.75)
254 (10.00)
241 (9.50)
12 × 12 × 8
323.8 (12.75)
219.1 (8.62)
254 (10.00)
229 (9.00)
12 × 12 × 6
323.8 (12.75)
168.3 (6.62)
254 (10.00)
219 (8.62)
12 × 12 × 5
323.8 (12.75)
141.3 (5.56)
254 (10.00)
216 (8.50)
14 × 14 × 12
355.6 (14.00)
323.8 (12.75)
279 (11.00)
270 (10.62)
14 × 14 × 10
355.6 (14.00)
273.0 (10.75)
279 (11.00)
257 (10.12)
14 × 14 × 8
355.6 (14.00)
219.1 (8.62)
279 (11.00)
248 (9.75)
14 × 14 × 6
355.6 (14.00)
168.3 (6.62)
279 (11.00)
238 (9.38)
16 × 16 × 14
406.4 (16.00)
355.6 (14.00)
305 (12.00)
305 (12.00)
16 × 16 × 12
406.4 (16.00)
323.8 (12.75)
305 (12.00)
295 (11.62)
16 × 16 × 10
406.4 (16.00)
273.0 (10.75)
305 (12.00)
283 (11.12)
16 × 16 × 8
406.4 (16.00)
219.1 (8.62)
305 (12.00)
273 (10.75)
16 × 16 × 6
406.4 (16.00)
168.3 (6.62)
305 (12.00)
264 (10.38)
18 × 18 × 16
457 (18.00)
406.4 (16.00)
343 (13.50)
330 (13.00)
18 × 18 × 14
457 (18.00)
355.6 (14.00)
343 (13.50)
330 (13.00)
18 × 18 × 12
457 (18.00)
323.8 (12.75)
343 (13.50)
321 (12.62)
18 × 18 × 10
457 (18.00)
273.0 (10.75)
343 (13.50)
308 (12.12)
18 × 18 × 8
457 (18.00)
219.1 (8.62)
343 (13.50)
298 (11.75)
20 × 20 × 18
508 (20.00)
457.0 (18.00)
381 (15.00)
368 (14.50)
20 × 20 × 16
508 (20.00)
406.4 (16.00)
381 (15.00)
356 (14.00)
20 × 20 × 14
508 (20.00)
355.6 (14.00)
381 (15.00)
356 (14.00)
14
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-8 Dimensions of Reducing Outlet Tees and Reducing Outlet Crosses (Cont’d)
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel, mm (in.)
Run
Outlet
Center-to-End, mm (in.)
Run, C
Outlet, M [Note (1)]
20 × 20 × 12
508 (20.00)
323.8 (12.75)
381 (15.00)
346 (13.62)
20 × 20 × 10
508 (20.00)
273.0 (10.75)
381 (15.00)
333 (13.12)
20 × 20 × 8
508 (20.00)
219.1 (8.62)
381 (15.00)
324 (12.75)
22 × 22 × 20
559 (22.00)
508.0 (20.00)
419 (16.50)
406 (16.00)
22 × 22 × 18
559 (22.00)
457.0 (18.00)
419 (16.50)
394 (15.50)
22 × 22 × 16
559 (22.00)
406.4 (16.00)
419 (16.50)
381 (15.00)
22 × 22 × 14
559 (22.00)
355.6 (14.00)
419 (16.50)
381 (15.00)
22 × 22 × 12
559 (22.00)
323.8 (12.75)
419 (16.50)
371 (14.62)
22 × 22 × 10
559 (22.00)
273.0 (10.75)
419 (16.50)
359 (14.12)
24 × 24 × 22
610 (24.00)
559.0 (22.00)
432 (17.00)
432 (17.00)
24 × 24 × 20
610 (24.00)
508.0 (20.00)
432 (17.00)
432 (17.00)
24 × 24 × 18
610 (24.00)
457.0 (18.00)
432 (17.00)
419 (16.50)
24 × 24 × 16
610 (24.00)
406.4 (16.00)
432 (17.00)
406 (16.00)
24 × 24 × 14
610 (24.00)
355.6 (14.00)
432 (17.00)
406 (16.00)
24 × 24 × 12
610 (24.00)
323.8 (12.75)
432 (17.00)
397 (15.62)
24 × 24 × 10
610 (24.00)
273.0 (10.75)
432 (17.00)
384 (15.12)
26 × 26 × 24
660 (26.00)
610.0 (24.00)
495 (19.50)
483 (19.00)
26 × 26 × 22
660 (26.00)
559.0 (22.00)
495 (19.50)
470 (18.50)
26 × 26 × 20
660 (26.00)
508.0 (20.00)
495 (19.50)
457 (18.00)
26 × 26 × 18
660 (26.00)
457.0 (18.00)
495 (19.50)
444 (17.50)
26 × 26 × 16
660 (26.00)
406.4 (16.00)
495 (19.50)
432 (17.00)
26 × 26 × 14
660 (26.00)
355.6 (14.00)
495 (19.50)
432 (17.00)
26 × 26 × 12
660 (26.00)
323.8 (12.75)
495 (19.50)
422 (16.62)
28 × 28 × 26
711 (28.00)
660.0 (26.00)
521 (20.50)
521 (20.50)
28 × 28 × 24
711 (28.00)
610.0 (24.00)
521 (20.50)
508 (20.00)
28 × 28 × 22
711 (28.00)
559.0 (22.00)
521 (20.50)
495 (19.50)
28 × 28 × 20
711 (28.00)
508.0 (20.00)
521 (20.50)
483 (19.00)
28 × 28 × 18
711 (28.00)
457.0 (18.00)
521 (20.50)
470 (18.50)
28 × 28 × 16
711 (28.00)
406.4 (16.00)
521 (20.50)
457 (18.00)
28 × 28 × 14
711 (28.00)
355.6 (14.00)
521 (20.50)
457 (18.00)
28 × 28 × 12
711 (28.00)
323.8 (12.75)
521 (20.50)
448 (17.62)
30 × 30 × 28
762 (30.00)
711.0 (28.00)
559 (22.00)
546 (21.50)
30 × 30 × 26
762 (30.00)
660.0 (26.00)
559 (22.00)
546 (21.50)
30 × 30 × 24
762 (30.00)
610.0 (24.00)
559 (22.00)
533 (21.00)
30 × 30 × 22
762 (30.00)
559.0 (22.00)
559 (22.00)
521 (20.50)
30 × 30 × 20
762 (30.00)
508.0 (20.00)
559 (22.00)
508 (20.00)
30 × 30 × 18
762 (30.00)
457.0 (18.00)
559 (22.00)
495 (19.50)
30 × 30 × 16
762 (30.00)
406.4 (16.00)
559 (22.00)
483 (19.00)
30 × 30 × 14
762 (30.00)
355.6 (14.00)
559 (22.00)
483 (19.00)
15
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-8 Dimensions of Reducing Outlet Tees and Reducing Outlet Crosses (Cont’d)
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel, mm (in.)
Run
Outlet
Center-to-End, mm (in.)
Run, C
Outlet, M [Note (1)]
30 × 30 × 12
762 (30.00)
323.8 (12.75)
559 (22.00)
473 (18.62)
30 × 30 × 10
762 (30.00)
273.0 (10.75)
559 (22.00)
460 (18.12)
32 × 32 × 30
813 (32.00)
762.0 (30.00)
597 (23.50)
584 (23.00)
32 × 32 × 28
813 (32.00)
711.0 (28.00)
597 (23.50)
572 (22.5)
32 × 32 × 26
813 (32.00)
660.0 (26.00)
597 (23.50)
572 (22.50)
32 × 32 × 24
813 (32.00)
610.0 (24.00)
597 (23.50)
559 (22.00)
32 × 32 × 22
813 (32.00)
559.0 (22.00)
597 (23.50)
546 (21.50)
32 × 32 × 20
813 (32.00)
508.0 (20.00)
597 (23.50)
533 (21.00)
32 × 32 × 18
813 (32.00)
457.0 (18.00)
597 (23.50)
521 (20.50)
32 × 32 × 16
813 (32.00)
406.4 (16.00)
597 (23.50)
508 (20.00)
32 × 32 × 14
813 (32.00)
355.6 (14.00)
597 (23.50)
508 (20.00)
34 × 34 × 32
864 (34.00)
813.0 (32.00)
635 (25.00)
622 (24.50)
34 × 34 × 30
864 (34.00)
762.0 (30.00)
635 (25.00)
610 (24.00)
34 × 34 × 28
864 (34.00)
711.0 (28.00)
635 (25.00)
597 (23.50)
34 × 34 × 26
864 (34.00)
660.0 (26.00)
635 (25.00)
597 (23.50)
34 × 34 × 24
864 (34.00)
610.0 (24.00)
635 (25.00)
584 (23.00)
34 × 34 × 22
864 (34.00)
559.0 (22.00)
635 (25.00)
572 (22.50)
34 × 34 × 20
864 (34.00)
508.0 (20.00)
635 (25.00)
559 (22.00)
34 × 34 × 18
864 (34.00)
457.0 (18.00)
635 (25.00)
546 (21.50)
34 × 34 × 16
864 (34.00)
406.4 (16.00)
635 (25.00)
533 (21.00)
36 × 36 × 34
914 (36.00)
864.0 (34.00)
673 (26.50)
660 (26.00)
36 × 36 × 32
914 (36.00)
813.0 (32.00)
673 (26.50)
648 (25.50)
36 × 36 × 30
914 (36.00)
762.0 (30.00)
673 (26.50)
635 (25.00)
36 × 36 × 28
914 (36.00)
711.0 (28.00)
673 (26.50)
622 (24.50)
36 × 36 × 26
914 (36.00)
660.0 (26.00)
673 (26.50)
622 (24.50)
36 × 36 × 24
914 (36.00)
610.0 (24.00)
673 (26.50)
610 (24.00)
36 × 36 × 22
914 (36.00)
559.0 (22.00)
673 (26.50)
597 (23.50)
36 × 36 × 20
914 (36.00)
508.0 (20.00)
673 (26.50)
584 (23.00)
36 × 36 × 18
914 (36.00)
457.0 (18.00)
673 (26.50)
572 (22.50)
36 × 36 × 16
914 (36.00)
406.4 (16.00)
673 (26.50)
559 (22.00)
38 × 38 × 36
965 (38.00)
914.0 (36.00)
711 (28.00)
711 (28.00)
38 × 38 × 34
965 (38.00)
864.0 (34.00)
711 (28.00)
698 (27.50)
38 × 38 × 32
965 (38.00)
813.0 (32.00)
711 (28.00)
686 (27.00)
38 × 38 × 30
965 (38.00)
762.0 (30.00)
711 (28.00)
673 (26.50)
38 × 38 × 28
965 (38.00)
711.0 (28.00)
711 (28.00)
648 (25.50)
38 × 38 × 26
965 (38.00)
660.0 (26.00)
711 (28.00)
648 (25.50)
38 × 38 × 24
965 (38.00)
610.0 (24.00)
711 (28.00)
635 (25.00)
38 × 38 × 22
965 (38.00)
559.0 (22.00)
711 (28.00)
622 (24.50)
38 × 38 × 20
965 (38.00)
508.0 (20.00)
711 (28.00)
610 (24.00)
38 × 38 × 18
965 (38.00)
457.0 (18.00)
711 (28.00)
597 (23.50)
16
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-8 Dimensions of Reducing Outlet Tees and Reducing Outlet Crosses (Cont’d)
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel, mm (in.)
Run
Outlet
Center-to-End, mm (in.)
Run, C
Outlet, M [Note (1)]
40 × 40 × 38
1 016 (40.00)
965.0 (38.00)
749 (29.50)
749 (29.50)
40 × 40 × 36
1 016 (40.00)
914.0 (36.00)
749 (29.50)
737 (29.00)
40 × 40 × 34
1 016 (40.00)
864.0 (34.00)
749 (29.50)
724 (28.50)
40 × 40 × 32
1 016 (40.00)
813.0 (32.00)
749 (29.50)
711 (28.00)
40 × 40 × 30
1 016 (40.00)
762.0 (30.00)
749 (29.50)
698 (27.50)
40 × 40 × 28
1 016 (40.00)
711.0 (28.00)
749 (29.50)
673 (26.50)
40 × 40 × 26
1 016 (40.00)
660.0 (26.00)
749 (29.50)
673 (26.50)
40 × 40 × 24
1 016 (40.00)
610.0 (24.00)
749 (29.50)
660 (26.00)
40 × 40 × 22
1 016 (40.00)
559.0 (22.00)
749 (29.50)
648 (25.50)
40 × 40 × 20
1 016 (40.00)
508.0 (20.00)
749 (29.50)
635 (25.00)
40 × 40 × 18
1 016 (40.00)
457.0 (18.00)
749 (29.50)
622 (24.50)
42 × 42 × 40
1 067 (42.00)
1 016.0 (40.00)
762 (30.00)
711 (28.00)
42 × 42 × 38
1 067 (42.00)
965.0 (38.00)
762 (30.00)
711 (28.00)
42 × 42 × 36
1 067 (42.00)
914.0 (36.00)
762 (30.00)
711 (28.00)
42 × 42 × 34
1 067 (42.00)
864.0 (34.00)
762 (30.00)
711 (28.00)
42 × 42 × 32
1 067 (42.00)
813.0 (32.00)
762 (30.00)
711 (28.00)
42 × 42 × 30
1 067 (42.00)
762.0 (30.00)
762 (30.00)
711 (28.00)
42 × 42 × 28
1 067 (42.00)
711.0 (28.00)
762 (30.00)
698 (27.50)
42 × 42 × 26
1 067 (42.00)
660.0 (26.00)
762 (30.00)
698 (27.50)
42 × 42 × 24
1 067 (42.00)
610.0 (24.00)
762 (30.00)
660 (26.00)
42 × 42 × 22
1 067 (42.00)
559.0 (22.00)
762 (30.00)
660 (26.00)
42 × 42 × 20
1 067 (42.00)
508.0 (20.00)
762 (30.00)
660 (26.00)
42 × 42 × 18
1 067 (42.00)
457.0 (18.00)
762 (30.00)
648 (25.50)
42 × 42 × 16
1 067 (42.00)
406.4 (16.00)
762 (30.00)
635 (25.00)
44 × 44 × 42
1 118 (44.00)
1 067.0 (42.00)
813 (32.00)
762 (30.00)
44 × 44 × 40
1 118 (44.00)
1 016.0 (40.00)
813 (32.00)
749 (29.50)
44 × 44 × 38
1 118 (44.00)
965.0 (38.00)
813 (32.00)
737 (29.00)
44 × 44 × 36
1 118 (44.00)
914.0 (36.00)
813 (32.00)
724 (28.50)
44 × 44 × 34
1 118 (44.00)
864.0 (34.00)
813 (32.00)
724 (28.50)
44 × 44 × 32
1 118 (44.00)
813.0 (32.00)
813 (32.00)
711 (28.00)
44 × 44 × 30
1 118 (44.00)
762.0 (30.00)
813 (32.00)
711 (28.00)
44 × 44 × 28
1 118 (44.00)
711.0 (28.00)
813 (32.00)
698 (27.50)
44 × 44 × 26
1 118 (44.00)
660.0 (26.00)
813 (32.00)
698 (27.50)
44 × 44 × 24
1 118 (44.00)
610.0 (24.00)
813 (32.00)
698 (27.50)
44 × 44 × 22
1 118 (44.00)
559.0 (22.00)
813 (32.00)
686 (27.00)
44 × 44 × 20
1 118 (44.00)
508.0 (20.00)
813 (32.00)
686 (27.00)
46 × 46 × 44
1 168 (46.00)
1 118.0 (44.00)
851 (33.50)
800 (31.50)
46 × 46 × 42
1 168 (46.00)
1 067.0 (42.00)
851 (33.50)
787 (31.00)
46 × 46 × 40
1 168 (46.00)
1 016.0 (40.00)
851 (33.50)
775 (30.50)
46 × 46 × 38
1 168 (46.00)
965.0 (38.00)
851 (33.50)
762 (30.00)
17
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-8 Dimensions of Reducing Outlet Tees and Reducing Outlet Crosses (Cont’d)
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel, mm (in.)
Run
Outlet
Center-to-End, mm (in.)
Run, C
Outlet, M [Note (1)]
46 × 46 × 36
1 168 (46.00)
914.0 (36.00)
851 (33.50)
762 (30.00)
46 × 46 × 34
1 168 (46.00)
864.0 (34.00)
851 (33.50)
749 (29.50)
46 × 46 × 32
1 168 (46.00)
813.0 (32.00)
851 (33.50)
749 (29.50)
46 × 46 × 30
1 168 (46.00)
762.0 (30.00)
851 (33.50)
737 (29.00)
46 × 46 × 28
1 168 (46.00)
711.0 (28.00)
851 (33.50)
737 (29.00)
46 × 46 × 26
1 168 (46.00)
660.0 (26.00)
851 (33.50)
737 (29.00)
46 × 46 × 24
1 168 (46.00)
610.0 (24.00)
851 (33.50)
724 (28.50)
46 × 46 × 22
1 168 (46.00)
559.0 (22.00)
851 (33.50)
724 (28.50)
48 × 48 × 46
1 219 (48.00)
1 168.0 (46.00)
889 (35.00)
838 (33.00)
48 × 48 × 44
1 219 (48.00)
1 118.0 (44.00)
889 (35.00)
838 (33.00)
48 × 48 × 42
1 219 (48.00)
1 067.0 (42.00)
889 (35.00)
813 (32.00)
48 × 48 × 40
1 219 (48.00)
1 016.0 (40.00)
889 (35.00)
813 (32.00)
48 × 48 × 38
1 219 (48.00)
965.0 (38.00)
889 (35.00)
813 (32.00)
48 × 48 × 36
1 219 (48.00)
914.0 (36.00)
889 (35.00)
787 (31.00)
48 × 48 × 34
1 219 (48.00)
864.0 (34.00)
889 (35.00)
787 (31.00)
48 × 48 × 32
1 219 (48.00)
813.0 (32.00)
889 (35.00)
787 (31.00)
48 × 48 × 30
1 219 (48.00)
762.0 (30.00)
889 (35.00)
762 (30.00)
48 × 48 × 28
1 219 (48.00)
711.0 (28.00)
889 (35.00)
762 (30.00)
48 × 48 × 26
1 219 (48.00)
660.0 (26.00)
889 (35.00)
762 (30.00)
48 × 48 × 24
1 219 (48.00)
610.0 (24.00)
889 (35.00)
737 (29.00)
48 × 48 × 22
1 219 (48.00)
559.0 (22.00)
889 (35.00)
737 (29.00)
NOTE: (1) Outlet dimension M for run sizes NPS 14 and larger is recommended but not required.
18
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-9 Dimensions of Lap Joint Stub Ends
Nominal
Pipe Size
(NPS)
Outside Diameter
of Barrel, mm (in.)
Long Pattern
Short Pattern
Radius of
Diameter of
Length, F, mm (in.) Length, F, mm (in.) Fillet, R, mm (in.) Lap, G, mm (in.)
[Notes (3), (4)]
[Notes (3), (4)]
[Note (5)]
[Note (6)]
Max.
Min.
1
22.8 (0.896)
20.5 (0.809)
76 (3.00)
51 (2.00)
3 (0.12)
35 (1.38)
3
28.1 (1.106)
25.9 (1.019)
76 (3.00)
51 (2.00)
3 (0.12)
43 (1.69)
∕2
∕4
1
35.0 (1.376)
32.6 (1.284)
102 (4.00)
51 (2.00)
3 (0.12)
51 (2.00)
11∕4
43.6 (1.716)
41.4 (1.629)
102 (4.00)
51 (2.00)
5 (0.19)
64 (2.50)
11∕2
49.9 (1.965)
47.5 (1.869)
102 (4.00)
51 (2.00)
6 (0.25)
73 (2.88)
2
62.4 (2.456)
59.5 (2.344)
152 (6.00)
64 (2.50)
8 (0.31)
92 (3.62)
21∕2
75.3 (2.966)
72.2 (2.844)
152 (6.00)
64 (2.50)
8 (0.31)
105 (4.12)
3
91.3 (3.596)
88.1 (3.469)
152 (6.00)
64 (2.50)
10 (0.38)
127 (5.00)
31∕2
104.0 (4.096)
100.8 (3.969)
152 (6.00)
76 (3.00)
10 (0.38)
140 (5.50)
4
116.7 (4.593)
113.5 (4.469)
152 (6.00)
76 (3.00)
11 (0.44)
157 (6.19)
5
144.3 (5.683)
140.5 (5.532)
203 (8.00)
76 (3.00)
11 (0.44)
186 (7.31)
6
171.3 (6.743)
167.5 (6.594)
203 (8.00)
89 (3.50)
13 (0.50)
216 (8.50)
8
222.1 (8.743)
218.3 (8.594)
203 (8.00)
102 (4.00)
13 (0.50)
270 (10.62)
10
277.2 (10.913)
272.3 (10.719)
254 (10.00)
127 (5.00)
13 (0.50)
324 (12.75)
12
328.0 (12.913)
323.1 (12.719)
254 (10.00)
152 (6.00)
13 (0.50)
381 (15.00)
14
359.9 (14.170)
354.8 (13.969)
305 (12.00)
152 (6.00)
13 (0.50)
413 (16.25)
16
411.0 (16.180)
405.6 (15.969)
305 (12.00)
152 (6.00)
13 (0.50)
470 (18.50)
18
462.0 (18.190)
456.0 (17.969)
305 (12.00)
152 (6.00)
13 (0.50)
533 (21.00)
20
514.0 (20.240)
507.0 (19.969)
305 (12.00)
152 (6.00)
13 (0.50)
584 (23.00)
22
565.0 (22.240)
558.0 (21.969)
305 (12.00)
152 (6.00)
13 (0.50)
641 (25.25)
24
616.0 (24.240)
609.0 (23.969)
305 (12.00)
152 (6.00)
13 (0.50)
692 (27.25)
GENERAL NOTES:
(a) See Table 11-1 for tolerances.
(b) Service conditions and joint construction often dictate stub end length requirements. Therefore, the purchaser must specify long or short
pattern fitting when ordering.
NOTES:
(1) Gasket face finish shall be in accordance with ASME B16.5 for raised-face flanges.
(2) The lap thickness, T, shall not be less than nominal pipe wall thickness. See Table 11-1 for tolerance.
(3) When short pattern stub ends are used with larger flanges in Classes 300 and 600, with most sizes in Classes 900 and higher, and when long
pattern stub ends are used with larger flanges in Classes 1500 and 2500, it may be necessary to increase the length of the stub ends in order to
avoid covering the weld with the flange. Such increases in length shall be a matter of agreement between the manufacturer and purchaser.
(4) When special facings such as tongue and groove or male and female are employed, additional lap thickness must be provided and such
additional thickness shall be in addition to (not included in) the basic length, F.
(5) These dimensions conform to the radius established for lap joint flanges in ASME B16.5.
(6) This dimension conforms to standard machined facings shown in ASME B16.5. The back face of the lap shall be machined to conform to the
surface on which it sits. Where ring joint facings are to be applied, use dimension K as given in ASME B16.5.
19
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-10 Dimensions of Caps
E or E1
Nominal Pipe Size
(NPS)
Outside Diameter at Bevel,
mm (in.)
Length, E, mm (in.)
[Note (1)]
Limiting Wall Thickness
for Length, E, mm (in.)
Length, E1, mm (in.)
[Note (2)]
1
∕2
21.3 (0.84)
25 (1.00)
4.57 (0.18)
25 (1.00)
3
∕4
26.7 (1.05)
25 (1.00)
3.81 (0.15)
25 (1.00)
1
33.4 (1.32)
38 (1.50)
4.57 (0.18)
38 (1.50)
11∕4
42.2 (1.66)
38 (1.50)
4.83 (0.19)
38 (1.50)
11∕2
48.3 (1.90)
38 (1.50)
5.08 (0.20)
38 (1.50)
2
60.3 (2.38)
38 (1.50)
5.59 (0.22)
44 (1.75)
1
2 ∕2
73.0 (2.88)
38 (1.50)
7.11 (0.28)
51 (2.00)
3
88.9 (3.50)
51 (2.00)
7.62 (0.30)
64 (2.50)
31∕2
101.6 (4.00)
64 (2.50)
8.13 (0.32)
76 (3.00)
4
114.3 (4.50)
64 (2.50)
8.64 (0.34)
76 (3.00)
5
141.3 (5.56)
76 (3.00)
9.65 (0.38)
89 (3.50)
6
168.3 (6.62)
89 (3.50)
10.92 (0.43)
102 (4.00)
8
219.1 (8.62)
102 (4.00)
12.70 (0.50)
127 (5.00)
10
273.0 (10.75)
127 (5.00)
12.70 (0.50)
152 (6.00)
12
323.8 (12.75)
152 (6.00)
12.70 (0.50)
178 (7.00)
14
355.6 (14.00)
165 (6.50)
12.70 (0.50)
191 (7.50)
16
406.4 (16.00)
178 (7.00)
12.70 (0.50)
203 (8.00)
18
457.0 (18.00)
203 (8.00)
12.70 (0.50)
229 (9.00)
20
508.0 (20.00)
229 (9.00)
12.70 (0.50)
254 (10.00)
22
559.0 (22.00)
254 (10.00)
12.70 (0.50)
254 (10.00)
24
610.0 (24.00)
267 (10.50)
12.70 (0.50)
305 (12.00)
26
660.0 (26.00)
267 (10.50)
…
…
28
711.0 (28.00)
267 (10.50)
…
…
30
762.0 (30.00)
267 (10.50)
…
…
32
813.0 (32.00)
267 (10.50)
…
…
34
864.0 (34.00)
267 (10.50)
…
…
36
914.0 (36.00)
267 (10.50)
…
…
38
965.0 (38.00)
305 (12.00)
…
…
40
1 016.0 (40.00)
305 (12.00)
…
…
42
1 067.0 (42.00)
305 (12.00)
…
…
44
1 118.0 (44.00)
343 (13.50)
…
…
46
1 168.0 (46.00)
343 (13.50)
…
…
48
1 219.0 (48.00)
343 (13.50)
…
…
GENERAL NOTE: The shape of these caps shall be ellipsoidal and shall conform to the requirements given in the ASME Boiler and Pressure Vessel
Code.
NOTES:
(1) Length E applies for thickness not exceeding that given in column “Limiting Wall Thickness for Length, E.”
(2) Length E1 applies for thickness greater than that given in column “Limiting Wall Thickness for Length, E” for NPS 24 and smaller. For NPS 26
and larger, length E1 shall be by agreement between the manufacturer and purchaser.
20
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-11 Dimensions of Reducers
H
Nominal
Pipe
Size
(NPS)
3
∕4 × 1∕2
H
Outside Diameter
at Bevel, mm (in.)
Large
End
Small
End
End-to-End,
H, mm (in.)
Nominal
Pipe
Size
(NPS)
Outside Diameter
at Bevel, mm (in.)
Large
End
Small
End
End-to-End,
H, mm (in.)
26.7 (1.05)
21.3 (0.84)
38 (1.50)
3
26.7 (1.05)
17.3 (0.68)
38 (1.50)
5×4
141.3 (5.56)
114.3 (4.50)
127 (5.00)
1 × 3∕4
33.4 (1.32)
26.7 (1.05)
51 (2.00)
5 × 31∕2
141.3 (5.56)
101.6 (4.00)
127 (5.00)
1 × 1∕2
33.4 (1.32)
21.3 (0.84)
51 (2.00)
5×3
141.3 (5.56)
88.9 (3.50)
127 (5.00)
5 × 21∕2
141.3 (5.56)
73.0 (2.88)
127 (5.00)
5×2
141.3 (5.56)
60.3 (2.38)
127 (5.00)
6×5
168.3 (6.62)
141.3 (5.56)
140 (5.50)
6×4
168.3 (6.62)
114.3 (4.50)
140 (5.50)
3
∕4 × ∕8
11∕4 × 1
42.2 (1.66)
33.4 (1.32)
51 (2.00)
11∕4 × 3∕4
42.2 (1.66)
26.7 (1.05)
51 (2.00)
11∕4 × 1∕2
42.2 (1.66)
21.3 (0.84)
51 (2.00)
11∕2 × 11∕4
1
48.3 (1.90)
42.2 (1.66)
64 (2.50)
6 × 31∕2
168.3 (6.62)
101.6 (4.00)
140 (5.50)
1 ∕2 × 1
48.3 (1.90)
33.4 (1.32)
64 (2.50)
6×3
168.3 (6.62)
88.9 (3.50)
140 (5.50)
11∕2 × 3∕4
48.3 (1.90)
26.7 (1.05)
64 (2.50)
6 × 21∕2
168.3 (6.62)
73.0 (2.88)
140 (5.50)
11∕2 × 1∕2
48.3 (1.90)
21.3 (0.84)
64 (2.50)
8×6
219.1 (8.62)
168.3 (6.62)
152 (6.00)
2 × 11∕2
60.3 (2.38)
48.3 (1.90)
76 (3.00)
8×5
219.1 (8.62)
141.3 (5.56)
152 (6.00)
2 × 11∕4
60.3 (2.38)
42.2 (1.66)
76 (3.00)
8×4
219.1 (8.62)
114.3 (4.50)
152 (6.00)
2×1
60.3 (2.38)
33.4 (1.32)
76 (3.00)
8 × 31∕2
219.1 (8.62)
101.6 (4.00)
152 (6.00)
2 × 3∕4
60.3 (2.38)
26.7 (1.05)
76 (3.00)
10 × 8
273.0 (10.75)
219.1 (8.62)
178 (7.00)
21∕2 × 2
73.0 (2.88)
60.3 (2.38)
89 (3.50)
10 × 6
273.0 (10.75)
168.3 (6.62)
178 (7.00)
2 ∕2 × 1 ∕2
73.0 (2.88)
48.3 (1.90)
89 (3.50)
10 × 5
273.0 (10.75)
141.3 (5.56)
178 (7.00)
21∕2 × 11∕4
73.0 (2.88)
42.2 (1.66)
89 (3.50)
10 × 4
273.0 (10.75)
114.3 (4.50)
178 (7.00)
21∕2 × 1
73.0 (2.88)
33.4 (1.32)
89 (3.50)
12 × 10
323.8 (12.75)
273.0 (10.75)
203 (8.00)
3 × 21∕2
88.9 (3.50)
73.0 (2.88)
89 (3.50)
12 × 8
323.8 (12.75)
219.1 (8.62)
203 (8.00)
3×2
88.9 (3.50)
60.3 (2.38)
89 (3.50)
12 × 6
323.8 (12.75)
168.3 (6.62)
203 (8.00)
3 × 11∕2
88.9 (3.50)
48.3 (1.90)
89 (3.50)
12 × 5
323.8 (12.75)
141.3 (5.56)
203 (8.00)
3 × 11∕4
88.9 (3.50)
42.2 (1.66)
89 (3.50)
14 × 12
355.6 (14.00)
323.8 (12.75)
330 (13.00)
1
1
1
3 ∕2 × 3
101.6 (4.00)
88.9 (3.50)
102 (4.00)
14 × 10
355.6 (14.00)
273.0 (10.75)
330 (13.00)
31∕2 × 21∕2
101.6 (4.00)
73.0 (2.88)
102 (4.00)
14 × 8
355.6 (14.00)
219.1 (8.62)
330 (13.00)
31∕2 × 2
101.6 (4.00)
60.3 (2.38)
102 (4.00)
14 × 6
355.6 (14.00)
168.3 (6.62)
330 (13.00)
31∕2 × 11∕2
101.6 (4.00)
48.3 (1.90)
102 (4.00)
31∕2 × 11∕4
101.6 (4.00)
42.2 (1.66)
102 (4.00)
16 × 14
406.4 (16.00)
355.6 (14.00)
356 (14.00)
16 × 12
406.4 (16.00)
323.8 (12.75)
356 (14.00)
4 × 31∕2
114.3 (4.50)
101.6 (4.00)
102 (4.00)
16 × 10
406.4 (16.00)
273.0 (10.75)
356 (14.00)
4×3
114.3 (4.50)
88.9 (3.50)
102 (4.00)
16 × 8
406.4 (16.00)
219.1 (8.62)
356 (14.00)
4 × 21∕2
114.3 (4.50)
73.0 (2.88)
102 (4.00)
4×2
114.3 (4.50)
60.3 (2.38)
102 (4.00)
18 × 16
457 (18.00)
406.4 (16.00)
381 (15.00)
4 × 11∕2
114.3 (4.50)
48.3 (1.90)
102 (4.00)
18 × 14
457 (18.00)
355.6 (14.00)
381 (15.00)
21
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 6.1-11 Dimensions of Reducers (Cont’d)
Nominal
Pipe
Size
(NPS)
Outside Diameter
at Bevel, mm (in.)
Large
End
Small
End
End-to-End,
H, mm (in.)
18 × 12
457 (18.00)
323.8 (12.75)
381 (15.00)
18 × 10
457 (18.00)
273.0 (10.75)
381 (15.00)
Nominal
Pipe
Size
(NPS)
Outside Diameter
at Bevel, mm (in.)
Large
End
Small
End
End-to-End,
H, mm (in.)
36 × 34
914 (36.00)
864 (34.00)
610 (24.00)
36 × 32
914 (36.00)
813 (32.00)
610 (24.00)
20 × 18
508 (20.00)
457.0 (18.00)
508 (20.00)
36 × 30
914 (36.00)
762 (30.00)
610 (24.00)
20 × 16
508 (20.00)
406.4 (16.00)
508 (20.00)
36 × 26
914 (36.00)
660 (26.00)
610 (24.00)
20 × 14
508 (20.00)
355.6 (14.00)
508 (20.00)
36 × 24
914 (36.00)
610 (24.00)
610 (24.00)
20 × 12
508 (20.00)
323.8 (12.75)
508 (20.00)
38 × 36
965 (38.00)
914 (36.00)
610 (24.00)
22 × 20
559 (22.00)
508.0 (20.00)
508 (20.00)
38 × 34
965 (38.00)
864 (34.00)
610 (24.00)
22 × 18
559 (22.00)
457.0 (18.00)
508 (20.00)
38 × 32
965 (38.00)
813 (32.00)
610 (24.00)
22 × 16
559 (22.00)
406.4 (16.00)
508 (20.00)
38 × 30
965 (38.00)
762 (30.00)
610 (24.00)
22 × 14
559 (22.00)
355.4 (14.00)
508 (20.00)
38 × 28
965 (38.00)
711 (28.00)
610 (24.00)
38 × 26
965 (38.00)
660 (26.00)
610 (24.00)
24 × 22
610 (24.00)
559.0 (22.00)
508 (20.00)
24 × 20
610 (24.00)
508.0 (20.00)
508 (20.00)
40 × 38
1 016 (40.00)
965 (38.00)
610 (24.00)
24 × 18
610 (24.00)
457.0 (18.00)
508 (20.00)
40 × 36
1 016 (40.00)
914 (36.00)
610 (24.00)
24 × 16
610 (24.00)
406.4 (16.00)
508 (20.00)
40 × 34
1 016 (40.00)
864 (34.00)
610 (24.00)
40 × 32
1 016 (40.00)
813 (32.00)
610 (24.00)
40 × 30
1 016 (40.00)
762 (30.00)
610 (24.00)
26 × 24
660 (26.00)
610.0 (24.00)
610 (24.00)
26 × 22
660 (26.00)
559.0 (22.00)
610 (24.00)
26 × 20
660 (26.00)
508.0 (20.00)
610 (24.00)
42 × 40
1 067 (42.00)
1 016 (40.00)
610 (24.00)
26 × 18
660 (26.00)
457.0 (18.00)
610 (24.00)
42 × 38
1 067 (42.00)
965 (38.00)
610 (24.00)
42 × 36
1 067 (42.00)
914 (36.00)
610 (24.00)
28 × 26
711 (28.00)
660.0 (26.00)
610 (24.00)
42 × 34
1 067 (42.00)
864 (34.00)
610 (24.00)
28 × 24
711 (28.00)
610.0 (24.00)
610 (24.00)
42 × 32
1 067 (42.00)
813 (32.00)
610 (24.00)
28 × 20
711 (28.00)
508.0 (20.00)
610 (24.00)
42 × 30
1 067 (42.00)
762 (30.00)
610 (24.00)
28 × 18
711 (28.00)
457.0 (18.00)
610 (24.00)
44 × 42
1 118 (44.00)
1 067 (42.00)
610 (24.00)
30 × 28
762 (30.00)
711.0 (28.00)
610 (24.00)
44 × 40
1 118 (44.00)
1 016 (40.00)
610 (24.00)
30 × 26
762 (30.00)
660.0 (26.00)
610 (24.00)
44 × 38
1 118 (44.00)
965 (38.00)
610 (24.00)
30 × 24
762 (30.00)
610.0 (24.00)
610 (24.00)
44 × 36
1 118 (44.00)
914 (36.00)
610 (24.00)
30 × 20
762 (30.00)
508.0 (20.00)
610 (24.00)
46 × 44
1 168 (46.00)
1 118 (44.00)
711 (28.00)
32 × 30
813 (32.00)
762.0 (30.00)
610 (24.00)
46 × 42
1 168 (46.00)
1 067 (42.00)
711 (28.00)
32 × 28
813 (32.00)
711.0 (28.00)
610 (24.00)
46 × 40
1 168 (46.00)
1 016 (40.00)
711 (28.00)
32 × 26
813 (32.00)
660.0 (26.00)
610 (24.00)
46 × 38
1 168 (46.00)
965 (38.00)
711 (28.00)
32 × 24
813 (32.00)
610.0 (24.00)
610 (24.00)
48 × 46
1 219 (48.00)
1 168 (46.00)
711 (28.00)
34 × 32
864 (34.00)
813.0 (32.00)
610 (24.00)
48 × 44
1 219 (48.00)
1 118 (44.00)
711 (28.00)
34 × 30
864 (34.00)
762.0 (30.00)
610 (24.00)
48 × 42
1 219 (48.00)
1 067 (42.00)
711 (28.00)
34 × 26
864 (34.00)
660.0 (26.00)
610 (24.00)
48 × 40
1 219 (48.00)
1 016 (40.00)
711 (28.00)
34 × 24
864 (34.00)
610.0 (24.00)
610 (24.00)
GENERAL NOTE: Although the figure illustrates a bell-shaped reducer, the use of a conical reducer is not prohibited.
22
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 8-1 Welding Bevels and Root Face
ð18Þ
Nominal Wall Thickness, t, mm (in.)
End Preparation
Less than x [Note (2)]
Cut square or slightly chamfer, at manufacturer’s option (not illustrated)
x to 22 (0.88), inclusive [Note (2)]
Plain bevel as in illustration (a) above
More than 22 (0.88)
Compound bevel as in illustration (b) above
GENERAL NOTE: In the illustrations, dimensions in parentheses are in inches; other dimensions are in millimeters.
NOTES:
(1) See section 8 and Figure 8-1 for transition contours.
(2) x = 5 mm (0.19 in.) for carbon steel or ferritic alloy steel and 3 mm (0.12 in.) for austenitic steel or nonferrous alloys.
23
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
ð18Þ
Figure 8-1 Maximum Envelope for Welding End Transitions
NOTES:
(1) The value of tmin is whichever of the following is applicable:
(a) the minimum ordered wall thickness of the pipe, to include pipe that is purchased to a nominal wall thickness with an undertolerance other than
12.5%
(b) 0.875 times the nominal wall thickness of pipe ordered to a pipe schedule wall thickness that has an undertolerance of 12.5%
(2) The maximum thickness at the end of the component is as follows:
(a) the greater of [tmin + 4 mm (0.16 in.)] or 1.15tmin when ordered on a minimum wall basis
(b) the greater of [tmin + 4 mm (0.16 in.)] or 1.10tnom when ordered on a nominal wall basis
(3) Weld bevel shown is for illustration only.
(4) The weld reinforcement permitted by applicable code may lie outside the maximum envelope.
(5) Where transitions using maximum slope do not intersect the inside or outside surfaces within the transition region, as shown by the phantom
outline, maximum slopes shall be used. Alternatively, radii lying within the envelope may be used.
24
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
Table 9.2.1-1 Testing Coverage
Type of Fitting Tested [Note (1)]
Qualifies the Following If the Same Design Thickness Is Used
Short radius elbow [Note (2)]
Short radius, long radius, reducing long radius, or 3D radius elbow
Long radius elbow [Note (2)]
Long radius, reducing long radius, or 3D radius elbow
3D radius elbow [Note (2)]
3D radius elbow
Straight tee
Straight or reducing tees of any reduction
Reducing tee
Reducing tees with the same or more reduction in outlet size
Straight cross
Straight or reducing crosses of any reduction
Reducing cross
Reducing crosses with the same or more reduction in outlet size
Cap
Caps of the same configuration
Eccentric reducer [Note (3)]
Eccentric or concentric reducers with the same or lesser included transition angle
Concentric reducer [Note (3)]
Concentric reducers with the same or lesser included transition angle [Note (4)]
Lap joint stub ends
Lap joint stub ends are exempt from proof
NOTES:
(1) Paragraph 9.4 applies to as-tested and qualified fittings.
(2) A test of any angle elbow covered in Tables 6.1-1 through 6.1-6 will qualify any other angle. A factory-made segment elbow that has a proof test
on a geometrically similar 45-deg or 90-deg elbow need not be tested separately.
(3) Straight conical (no tangent) and bell-shaped reducers are considered different design configurations and require separate testing.
(4) “Transition angle” is defined as the angle of the conical section and is calculated as the [arc tan (difference of diameters/twice the length)] for
concentric reducers or [arc tan (difference of diameters/length)] for eccentric reducers.
Table 9.3.1-1 Test Factor, f, Determination
Number of Tests Performed, or Number of
Geometrically Similar Fittings Tested
Test
Factor, f
One
1.10
Two
1.05
Three or more
1.0
25
falatghareh.ir
falatghareh.ir
Table 11-1 Tolerances
26
Nominal Pipe
Size (NPS)
1
∕2 to 21∕2
DN
Outside
Diameter at
Bevel, D, mm (in.)
[Notes (3)
and (4)]
Inside
Diameter
at End, mm (in.)
[Notes (3) and
(5)]
90-deg and 45-deg
Long and
Short Radius
Elbows and Tees,
A, B, C, M
180-deg Returns
3D Radius
Elbows,
A, B
Overall
Length of
Reducers and
Lap Joint
Stub Ends,
F, H, mm (in.)
Overall
Length
of
Caps,
E, mm (in.)
Center-toCenter
Dimension,
O, mm (in.)
Back-toFace
Dimension,
K, mm (in.)
Alignment
of Ends,
U, mm (in.)
1 (0.03)
15 to 65
+1.6, −0.8 (+0.06, −0.03)
0.8 (0.03)
2 (0.06)
3 (0.09)
2 (0.06)
3 (0.12)
6 (0.25)
6 (0.25)
3 to 31∕2
80 to 90
1.6 (0.06)
1.6 (0.06)
2 (0.06)
3 (0.09)
2 (0.06)
3 (0.12)
6 (0.25)
6 (0.25)
1 (0.03)
4
100
1.6 (0.06)
1.6 (0.06)
2 (0.06)
3 (0.09)
2 (0.06)
3 (0.12)
6 (0.25)
6 (0.25)
1 (0.03)
5 to 8
125 to 200
+2.4, −1.6 (+0.09, −0.06)
1.6 (0.06)
2 (0.06)
3 (0.09)
2 (0.06)
6 (0.25)
6 (0.25)
6 (0.25)
1 (0.03)
10 to 18
250 to 450
+4.0, −3.2 (+0.16, −0.12)
3.2 (0.12)
2 (0.09)
3 (0.12)
2 (0.09)
6 (0.25)
10 (0.38)
6 (0.25)
2 (0.06)
20 to 24
500 to 600
+6.4, −4.8 (+0.25, −0.19)
4.8 (0.19)
2 (0.09)
3 (0.12)
2 (0.09)
6 (0.25)
10 (0.38)
6 (0.25)
2 (0.06)
26 to 30
650 to 750
+6.4, −4.8 (+0.25, −0.19)
4.8 (0.19)
3 (0.12)
6 (0.25)
5 (0.19)
10 (0.38)
…
…
…
32 to 48
800 to 1 200
+6.4, −4.8 (+0.25, −0.19)
4.8 (0.19)
5 (0.19)
6 (0.38)
5 (0.19)
10 (0.38)
…
…
…
Lap Joint Stub Ends [Note (6)]
Angularity Tolerances, mm (in.)
Outside
Diameter
of Lap,
G, mm (in.)
Fillet
Radius
of Lap,
R, mm (in.)
Lap
Thickness, mm (in.)
15 to 65
+0, −1 (+0, −0.03)
+0, −1 (+0, −0.03)
+1.6, −0 (+0.06, −0)
1
3 to 31∕2
80 to 90
+0, −1 (+0, −0.03)
+0, −1 (+0, −0.03)
+1.6, −0 (+0.06, −0)
4
100
+0, −1 (+0, −0.03)
+0, −2 (+0, −0.06)
5 to 8
125 to 200
+0, −1 (+0, −0.03)
+0, −2 (+0, −0.06)
Nominal
Pipe Size
(NPS)
1
∕2 to 21∕2
DN
Nominal Pipe
Size
(NPS)
∕2 to 4
DN
Off
Angle,
Q
Off
Plane,
P
15 to 100
1 (0.03)
2 (0.06)
5 to 8
125 to 200
2 (0.06)
4 (0.12)
+1.6, −0 (+0.06, −0)
10 to 12
250 to 300
3 (0.09)
5 (0.19)
+1.6, −0 (+0.06, −0)
14 to 16
350 to 400
3 (0.09)
6 (0.25)
ASME B16.9-2018
Center-to-End
Dimensions, mm (in.)
All Fittings [Notes (1) and (2)]
falatghareh.ir
falatghareh.ir
Table 11-1 Tolerances (Cont’d)
Lap Joint Stub Ends [Note (6)]
Nominal
Pipe Size
(NPS)
DN
Outside
Diameter
of Lap,
G, mm (in.)
Angularity Tolerances, mm (in.)
Fillet
Radius
of Lap,
R, mm (in.)
Lap
Thickness, mm (in.)
Nominal Pipe
Size
(NPS)
DN
Off
Angle,
Q
Off
Plane,
P
10 to 18
250 to 450
+0, −2 (+0, −0.06)
+0, −2 (+0, −0.06)
+3.2, −0 (+0.12, −0)
18 to 24
450 to 600
4 (0.12)
10 (0.38)
20 to 24
500 to 600
+0, −2 (+0, −0.06)
+0, −2 (+0, −0.06)
+3.2, −0 (+0.12, −0)
26 to 30
650 to 750
5 (0.19)
10 (0.38)
26 to 30
650 to 750
…
…
…
32 to 42
800 to 1 050
5 (0.19)
13 (0.50)
32 to 48
800 to 1 200
…
…
…
44 to 48
1 100 to 1 200
5 (0.19)
19 (0.75)
GENERAL NOTE: Tolerances are equal plus and minus except as noted.
27
ASME B16.9-2018
NOTES:
(1) The inside diameter and the nominal wall thicknesses at ends are to be specified by the purchaser.
(2) A minimum wall thickness of 87.5% applies unless the purchaser specifies a different wall thickness tolerance. See Figure 8-1, Note (1)(a).
(3) Out-of-round is the sum of absolute values of plus and minus tolerances.
(4) This tolerance may not apply in localized areas of formed fittings where increased wall thickness is required to meet design requirements of para. 2.2.
(5) Unless otherwise specified by the purchaser, these tolerances apply to the nominal inside diameter, which equals the difference between the nominal outside diameter and twice the nominal
wall thickness.
(6) See Table 6.1-9 for limiting dimensions of outside diameter of barrel.
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
ð18Þ
MANDATORY APPENDIX I
REFERENCES
The following is a list of standards and specifications
referenced in this Standard. Unless otherwise specified,
the latest edition of ASME publications shall apply.
ASTM B361-16, Specification for Factory-Made Wrought
Aluminum and Aluminum-Alloy Welding Fittings
ASTM B363-14, Specification for Seamless and Welded
Unalloyed Titanium and Titanium Alloy Welding
Fittings
ASTM B366/B366M-17, Specification for Factory-Made
Wrought Nickel and Nickel Alloy Fittings
ASTM E29-13, Practice for Using Significant Digits in Test
Data to Determine Conformance With Specifications
Publisher: American Society for Testing and Materials
(ASTM International), 100 Barr Harbor Drive, P.O.
Box C700, West Conshohocken, PA 19428-2959
(www.astm.org)
ASME B16.5, Pipe Flanges and Flanged Fittings: NPS 1∕2
Through NPS 24 Metric/Inch Standard
ASME B16.25, Buttwelding Ends
ASME B31, Code for Pressure Piping
ASME B31.3, Process Piping
ASME B36.10M, Welded and Seamless Wrought Steel Pipe
ASME B36.19M, Stainless Steel Pipe
ASME Boiler and Pressure Vessel Code
Publisher: The American Society of Mechanical Engineers
(ASME), Two Park Avenue, New York, NY 10016-5990
(www.asme.org)
ISO 6708:1995, Pipework components — Definition and
selection of DN (nominal size)
ISO 9000:2015, Quality management systems —
Fundamentals and vocabulary1
ISO 9001:2015, Quality management systems —
Requirements1
ISO 9004:2009, Managing for the sustained success of an
organization — A quality management approach1
Publisher: International Organization for Standardization
(ISO), Central Secretariat, Chemin de Blandonnet 8, Case
Postale 401, 1214 Vernier, Geneva, Switzerland
(www.iso.org)
ASTM A234/A234M-17, Specification for Piping Fittings
of Wrought Carbon Steel and Alloy Steel for Moderate
and High Temperature Service
ASTM A403/A403M-16, Specification for Wrought
Austenitic Stainless Steel Piping Fittings
ASTM A420/A420M-16, Specification for Piping Fittings
of Wrought Carbon Steel and Alloy Steel for LowTemperature Service
ASTM A815/A815M-14e1, Specification for Wrought
Ferritic, Ferritic/Austenitic and Martensitic Stainless
Steel Piping Fittings
ASTM A960/A960M-16a, Specification for Common
Requirements for Wrought Steel Piping Fittings
1
May also be obtained from the American National Standards Institute
(ANSI), 25 West 43rd Street, New York, NY 10036.
28
falatghareh.ir
falatghareh.ir
ASME B16.9-2018
NONMANDATORY APPENDIX A
QUALITY SYSTEM PROGRAM
The products manufactured in accordance with this
Standard shall be produced under a Quality System
Program following the principles of an appropriate standard from the ISO 9000 series.1 A determination of the
need for registration and/or certification of the
product manufacturer’s quality system by an independent
organization shall be the responsibility of the manufacturer. The detailed documentation demonstrating program
compliance shall be available to the purchaser at the
manufacturer’s facility. A written summary description
of the program used by the product manufacturer shall
be available to the purchaser upon request. The
“product manufacturer” is defined as the entity whose
name or trademark appears on the product in accordance
with the marking or identification requirements of this
Standard.
1
The series is also available from the American National Standards
Institute (ANSI) and the American Society for Quality (ASQ) as
American National Standards that are identified by the prefix “Q,” replacing the prefix “ISO.” Each standard of the series is listed under
References in Mandatory Appendix I.
29
falatghareh.ir
falatghareh.ir
ASME B16.9-2018