3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
Safety Data Sheet
Copyright,2021, 3M Canada Company.
All rights reserved. Copying and/or downloading of this information for
the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes
unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed
with the intention of earning a profit thereon.
Document group:
Issue Date:
32-7916-3
2021/03/01
Version number:
Supercedes Date:
3.02
2020/10/22
This Safety Data Sheet has been prepared in accordance with the Canadian Hazardous Products Regulations.
SECTION 1: Identification
1.1. Product identifier
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
Product Identification Numbers
62-6137-0260-4
62-6137-0265-3
62-6165-3860-9
62-6165-3865-8
UU-0015-0377-8
UU-0015-0378-6
62-6165-0360-3
62-6165-3866-6
UU-0015-0446-1
62-6165-0365-2
UU-0015-0267-1
UU-0015-0457-8
62-6165-0366-0
UU-0015-0368-7
UU-0015-0463-6
1.2. Recommended use and restrictions on use
Intended Use
Adhesive
Restrictions on use
Not applicable
1.3. Supplier’s details
Company:
Division:
Address:
Telephone:
Website:
3M Canada Company
Industrial Adhesives and Tapes Division
1840 Oxford Street East, Post Office Box 5757, London, Ontario
(800) 364-3577
www.3M.ca
N6A 4T1
1.4. Emergency telephone number
Medical Emergency Telephone:1-800-3M HELPS / 1-800-364-3577; Transportation Emergency Telephone (CANUTEC):
(613) 996-6666
SECTION 2: Hazard identification
2.1. Classification of the substance or mixture
Flammable Liquid: Category 4.
Serious Eye Damage/Irritation: Category 2A.
Specific Target Organ Toxicity (single exposure): Category 3.
2.2. Label elements
Signal word
__________________________________________________________________________________________
Page: 1 of
9
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
Warning
Symbols
Exclamation mark
|
Pictograms
Hazard statements
Combustible liquid.
Causes serious eye irritation. May cause respiratory irritation.
Precautionary statements
Prevention:
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Avoid breathing
dust/fume/gas/mist/vapours/spray. Use only outdoors or in a well-ventilated area. Wear protective gloves and eye/face
protection. Wash exposed skin thoroughly after handling.
Response:
IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF IN EYES: Rinse cautiously with water
for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get
medical advice/attention. Call a POISON centre or doctor/physician if you feel unwell. In case of fire: Use a fire fighting
agent suitable for flammable liquids such as dry chemical or carbon dioxide to extinguish.
Storage:
Store in a well-ventilated place.
Keep container tightly closed. Store locked up.
Disposal:
Dispose of contents/container in accordance with applicable local/regional/national/international regulations.
2.3. Other hazards
May bond tissue rapidly.
SECTION 3: Composition/information on ingredients
This material is a mixture.
Ingredient
Ethyl Cyanoacrylate
Non-Hazardous Resin
C.A.S. No.
7085-85-0
Trade Secret
% by Wt
80 - 100 Trade Secret *
5 - 15
Common Name
2-Propenoic acid, 2-cyano-, ethyl ester
Not Applicable
Non-Hazardous Resin is a non-hazardous Trade Secret material according to WHMIS criteria.
*The actual concentration of this ingredient has been withheld as a trade secret.
SECTION 4: First aid measures
4.1. Description of first aid measures
Inhalation:
__________________________________________________________________________________________
Page: 2 of
9
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
Remove person to fresh air.
If you feel unwell, get medical attention.
Skin Contact:
FOR SKIN BONDS: Quickly soak in warm water and avoid use of excessive force to free bonded area. If unable to free bonded area, or if
lips or mouth are bonded, get medical attention. If irritation persists, get medical attention.
Eye Contact:
Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention. DO NOT force eyelids open.
If Swallowed:
Rinse mouth. If you feel unwell, get medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Irritating to the respiratory tract (coughing, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain).
4.3. Indication of any immediate medical attention and special treatment required
Not applicable
SECTION 5: Fire-fighting measures
5.1. Suitable extinguishing media
In case of fire: Use a fire fighting agent suitable for flammable liquids such as dry chemical or carbon dioxide to extinguish.
5.2. Special hazards arising from the substance or mixture
Closed containers exposed to heat from fire may build pressure and explode.
Hazardous Decomposition or By-Products
Substance
Carbon monoxide
Carbon dioxide
Hydrogen Cyanide
Oxides of Nitrogen
Condition
During Combustion
During Combustion
During Combustion
During Combustion
5.3. Special protective actions for fire-fighters
Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and
prevent explosive rupture.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
Evacuate area. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Use only non-sparking tools.
Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or
exhaust vapours, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and
could cause flammable gases or vapours in the spill area to burn or explode. Refer to other sections of this SDS for
information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.
6.2. Environmental precautions
Avoid release to the environment.
bodies of water.
For larger spills, cover drains and build dikes to prevent entry into sewer systems or
6.3. Methods and material for containment and cleaning up
Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially
available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent
material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible
using non-sparking tools. Place in a closed container approved for transportation by appropriate authorities. Clean up
residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and
follow safety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as
__________________________________________________________________________________________
Page: 3 of
9
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
possible in accordance with applicable local/regional/national/international regulations.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Avoid breathing dust/fume/gas/mist/vapours/spray.
Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after
handling. Avoid release to the environment. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.)
7.2. Conditions for safe storage including any incompatibilities
Store in a well-ventilated place. Keep cool. Keep container tightly closed to prevent contamination with water or air. If
contamination is suspected, do not reseal container. Store away from heat. Store away from acids. Store away from
strong bases. Store away from oxidizing agents. Store away from amines.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available
for the component.
Ingredient
C.A.S. No. Agency
Limit type
Additional Comments
Ethyl Cyanoacrylate
7085-85-0 ACGIH
TWA:0.2 ppm;STEL:1 ppm
Dermal/Respiratory
Sensitizer
ACGIH : American Conference of Governmental Industrial Hygienists
AIHA : American Industrial Hygiene Association
CMRG : Chemical Manufacturer's Recommended Guidelines
TWA: Time-Weighted-Average
STEL: Short Term Exposure Limit
CEIL: Ceiling
8.2. Exposure controls
8.2.1. Engineering controls
Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure
Limits and/or control dust/fume/gas/mist/vapours/spray. If ventilation is not adequate, use respiratory protection equipment.
8.2.2. Personal protective equipment (PPE)
Eye/face protection
Select and use eye/face protection to prevent contact based on the results of an exposure assessment.
protection(s) are recommended:
Indirect Vented Goggles
The following eye/face
Skin/hand protection
Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the
results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the
substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.
Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective
clothing. Do not wear cotton gloves. Note: Nitrile gloves may be worn over polymer laminate gloves to improve
dexterity.
Gloves made from the following material(s) are recommended: Polymer laminate
When only incidental contact is anticipated, alternative glove material(s) may be used. If contact with the glove does occur,
remove immediately and replace with a set of new gloves. For incidental contact, gloves made of the following material(s)
__________________________________________________________________________________________
Page: 4 of
9
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
may be used:Nitrile Rubber
Respiratory protection
An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part
of a full respiratory protection program. Based on the results of the exposure assessment, select from the following
respirator type(s) to reduce inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for organic vapours and particulates
For questions about suitability for a specific application, consult with your respirator manufacturer.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state
Colour
Odour
Odour threshold
pH
Melting point/Freezing point
Boiling point
Flash Point
Evaporation rate
Flammability (solid, gas)
Flammable Limits(LEL)
Flammable Limits(UEL)
Vapour Pressure
Viscosity/Kinematic Viscosity
Viscosity/Kinematic
Viscosity
Density
Relative density
Water solubility
Solubility- non-water
Partition coefficient: n-octanol/ water
Autoignition temperature
Decomposition temperature
Viscosity/Kinematic Viscosity
Volatile Organic Compounds
Percent volatile
VOC Less H2O & Exempt Solvents
Liquid
Colourless
Sharp Odour, Pungent Odour
No Data Available
Not Applicable
Not Applicable
150 ºC
85 ºC [Test Method:Closed Cup]
No Data Available
Not Applicable
No Data Available
No Data Available
39.1 Pa [@ 23.9 ºC ]
No Data Available
1.08 g/ml
1.08 [Ref Std:WATER=1]
Nil
No Data Available
No Data Available
No Data Available
No Data Available
1,275 - 1,650 mPa-s [@ 23 ºC ]
<=0.6 %
85 - 95 % weight [Test Method:Estimated]
<=6 g/l
Nanoparticles
This material does not contain nanoparticles.
SECTION 10: Stability and reactivity
10.1. Reactivity
This material may be reactive with certain agents under certain conditions - see the remaining headings in this section.
10.2. Chemical stability
Stable.
10.3. Possibility of hazardous reactions
__________________________________________________________________________________________
Page: 5 of
9
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
Hazardous polymerization may occur.
Material polymerizes rapidly by contact with water, alcohol, amines and alkalis.
10.4. Conditions to avoid
Heat
10.5. Incompatible materials
Strong oxidizing agents
Water
Strong bases
Amines
Alcohols
10.6. Hazardous decomposition products
Substance
None known.
Condition
Refer to section 5.2 for hazardous decomposition products during combustion.
SECTION 11: Toxicological information
The information below may not be consistent with the material classification in Section 2 if specific ingredient
classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be
reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be
present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be
relevant to the material as a whole.
11.1. Information on Toxicological effects
Signs and Symptoms of Exposure
Based on test data and/or information on the components, this material may produce the following health effects:
Inhalation:
Respiratory Tract Irritation:
and throat pain.
Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose
Skin Contact:
Bonds skin rapidly. Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Contact through clothing may cause thermal burns.
Eye Contact:
Bonds eyelids rapidly. Severe Eye Irritation: Signs/symptoms may include significant redness, swelling, pain, tearing,
cloudy appearance of the cornea, and impaired vision.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
Toxicological Data
If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or
the data are not sufficient for classification.
Acute Toxicity
Name
Overall product
Route
Ingestion
Species
Value
No data available; calculated ATE >5,000 mg/kg
Ethyl Cyanoacrylate
Dermal
Rabbit
LD50 > 2,000 mg/kg
__________________________________________________________________________________________
Page: 6 of
9
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
Ethyl Cyanoacrylate
Non-Hazardous Resin
Ingestion
Dermal
Rat
LD50 > 5,000 mg/kg
LD50 estimated to be > 5,000 mg/kg
Non-Hazardous Resin
Ingestion
Rat
LD50 > 5,000 mg/kg
Name
Species
Value
Ethyl Cyanoacrylate
Non-Hazardous Resin
Rabbit
Rabbit
Mild irritant
No significant irritation
Name
Species
Value
Ethyl Cyanoacrylate
Non-Hazardous Resin
Rabbit
Rabbit
Severe irritant
Mild irritant
Species
Human
Value
Not classified
Name
Species
Value
Ethyl Cyanoacrylate
Human
Not classified
ATE = acute toxicity estimate
Skin Corrosion/Irritation
Serious Eye Damage/Irritation
Skin Sensitization
Name
Ethyl Cyanoacrylate
Respiratory Sensitization
Germ Cell Mutagenicity
Name
Route
Value
Ethyl Cyanoacrylate
In Vitro
Not mutagenic
Carcinogenicity
For the component/components, either no data are currently available or the data are not sufficient for classification.
Reproductive Toxicity
Reproductive and/or Developmental Effects
For the component/components, either no data are currently available or the data are not sufficient for classification.
Target Organ(s)
Specific Target Organ Toxicity - single exposure
Name
Route
Target Organ(s)
Value
Species
Test result
Ethyl Cyanoacrylate
Inhalation
respiratory irritation
May cause respiratory irritation
Human
NOAEL Not
available
Exposure
Duration
occupational
exposure
Specific Target Organ Toxicity - repeated exposure
For the component/components, either no data are currently available or the data are not sufficient for classification.
Aspiration Hazard
For the component/components, either no data are currently available or the data are not sufficient for classification.
Please contact the address or phone number listed on the first page of the SDS for additional toxicological information
on this material and/or its components.
SECTION 12: Ecological information
__________________________________________________________________________________________
Page: 7 of
9
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
No data available.
SECTION 13: Disposal considerations
13.1. Disposal methods
Dispose of contents/ container in accordance with the local/regional/national/international regulations.
Dispose of completely cured (or polymerized) material in a permitted industrial waste facility. As a disposal alternative,
incinerate uncured product in a permitted waste incineration facility. Proper destruction may require the use of additional fuel
during incineration processes. Empty drums/barrels/containers used for transporting and handling hazardous chemicals
(chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered,
stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the
respective regulating authorities to determine the available treatment and disposal facilities.
SECTION 14: Transport Information
For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.
SECTION 15: Regulatory information
15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture
Global inventory status
Contact 3M for more information. The components of this material are in compliance with the provisions of the Korea
Chemical Control Act. Certain restrictions may apply. Contact the selling division for additional information. The
components of this material are in compliance with the provisions of Australia National Industrial Chemical Notification and
Assessment Scheme (NICNAS). Certain restrictions may apply. Contact the selling division for additional information. The
components of this material are in compliance with the provisions of Japan Chemical Substance Control Law. Certain
restrictions may apply. Contact the selling division for additional information. The components of this material are in
compliance with the provisions of Philippines RA 6969 requirements. Certain restrictions may apply. Contact the selling
division for additional information. The components of this product are in compliance with the new substance notification
requirements of CEPA. This product complies with Measures on Environmental Management of New Chemical
Substances. All ingredients are listed on or exempt from on China IECSC inventory. The components of this product are in
compliance with the chemical notification requirements of TSCA. All required components of this product are listed on the
active portion of the TSCA Inventory.
SECTION 16: Other information
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to
address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or
similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material
but also include the toxic properties of combustion or decomposition products that are known to be generated in
significant quantities.
Health: 2 Flammability: 2 Instability: 1 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address
the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar
emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include
the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.
__________________________________________________________________________________________
Page: 8 of
9
3M(TM) Scotch-Weld(TM) Plastic & Rubber Instant Adhesive PR1500, Clear
Document group:
32-7916-3
Version number:
3.02
Issue Date:
2021/03/01
Supercedes Date:
2020/10/22
The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. The manufacturer MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO,
ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF PERFORMANCE,
COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User is responsible for determining whether the product is fit
for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use
and application of a product, some of which are uniquely within the user's knowledge and control, it is essential that the user
evaluate the product to determine whether it is fit for a particular purpose and suitable for user's method of use or application.
3M Canada SDSs are available at www.3M.ca
__________________________________________________________________________________________
Page: 9 of
9