NSX-SZ35 EZ SERVICE MANUAL COMPACT DISC STEREO CASSETTE RECEIVER BASIC TAPE MECHANISM : ZZM–3 YPR1NF BASIC CD MECHANISM : AZG-1 YZD8RDM SYSTEM CD CASSEIVER SPEAKER REMOTE CONTROLLER NSX-SZ35 CX-NSZ35 SX-WNSZ35 RC-ZAS02 • This Service Manual is the "Revision Publishing" and replaces "Simple Manual" (S/M Code No. 09-001-425-8T1). S/M Code No. 09-003-425-8R1 RE VI SIO DA N TA • If requiring information about the CD mechanism, see Service Manual of AZG–1, (S/M Code No. 09-001-335-3N6). SPECIFICATIONS FM Tuner section Tuning range Usable sensitivity (IHF) Antenna terminals MW Tuner section Tuning range 87.5 MHz to 108 MHz 16.8 dBf 75 ohms (unbalanced) Usable sensitivity Antenna 531 kHz to 1602 kHz (9 kHz step) 530 kHz to 1710 kHz (10 kHz step) 350 µV/m Loop antenna LW Tuner section Tuning range Usable sensitivity Antenna 144 kHz to 290 kHz 1400 µV/m Loop antenna Amplifier section Mid-high frequency amplifier Power output Rated: 8 W + 8 W (8 ohms, T.H.D. 1 %, 1 kHz / DIN 45500) Reference: 10 W + 10 W (8 ohms, T.H.D. 10 %, 1 kHz / DIN 45324) DIN MUSIC POWER: 20 W + 20 W Total harmonic distortion 0.1 % (5 W, 1 kHz, 8 ohms, DIN AUDIO) Low frequency amplifier Power output Rated: 24 W + 24 W (6 ohms, T.H.D. 1 %, 130 Hz / DIN 45500) Reference: 30 W + 30 W (6 ohms, T.H.D. 10 %, 130 Hz / DIN 45324) DIN MUSIC POWER: 50 W+ 50 W Total harmonics distortion 0.1 % (15 W, 130 Hz, 6 ohms, DIN AUDIO) Inputs VIDEO: 500 mV Outputs SPEAKERS HIGH FREQ: accept speakers of 8 ohms or more SPEAKERS LOW FREQ: accept speakers of 6 ohms or more PHONES (stereo lack): accepts handphones of 32 ohms or more Cassette deck section Track format Frequency response Recording system Heads Compact disc player section Laser D-A converter Signal-to-noise ratio Harmonic distortion General Power requirements Power consumption Power consumption in in standby mode Dimensions (W x H x D) Weight Semiconductor laser (λ =780 nm) 1 bit dual 85 dB (1 kHz, 0 dB) 0.05% (1 kHz, 0 dB) 230 V AC, 50Hz 80 W 14 W with power–economizing mode off 0.9 W with power–economizing mode on 260 x 328 x 335 mm 6.8 kg Speaker system SX-WNSZ35 Speaker system 3 way, Built–in subwoofer (magnetic shielded type) Speaker units Subwoofer : 160 mm cone type Full range : 100 mm cone type Super tweeter: 20 mm ceramic type Impedance 6 ohms / 8 ohms Sensitivity 87 dB / W / m Dimensions (W x H x D) 240 x 324 x 260 mm Weight 4.5 kg • Design and specifications are subject to change without notice. • The word "BBE"and the "BBE symbol" are trademarks of BBE Sound, Inc. Under license from BBE Sound,Inc. 4 tracks, 2 channels stereo 50 Hz – 15 kHz AC bias Deck 1 : Playback head x 1 Deck 2 : Recording/playback head x 1, erase head x 1 –2– PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures WARNING! other than those specified herein may result in hazardous radiation exposure. WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO ATTENTION CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE L'utilisation de commandes, réglages ou procédures autres que FROM A DISTANCE OF MORE THAN 30cm FROM THE ceux spécifiés peut entraîner une dangereuse exposition aux radiations. SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling. ADVARSEL! Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. VAROITUS! Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylitCLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 tävälle näkymättömälle lasersäteilylle. VARNING! LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1. Precaution to replace Optical block (KSM-880CAB) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure. PICK-UP Assy P.C.B solder –3– NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 1 2 3 4 5 MAIN C.B Remove the AC power cord. Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) Contact the same end of the discharging resistor as step 3 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. D101 3 2 Select a discharging resistor referring to the following table. C102 4 2 Fig-1 Charging voltage (V) Discharging (C101, 102) resistor (Ω) 25-48 100 3 87-A00-247-090 49-140 220 5 87-A00-232-090 Rated power (W) C101 Parts number Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”. • Good or no good judgement of the MICROCOMPUTER 1 2 3 Turn on the AC main power. Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good. –4– In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset M IC RO CO M PU TE R There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 1 Remove the AC power cord. FRONT C.B 18 15 C113 % VSS MICROC113 COMPUTER * VDD FRONT C.B Short with tweezers. Fig-2-2 2 3 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROCOMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. –5– ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI NO. DESCRIPTION REF. NO. PART NO. IC 87-A21-396-010 87-A21-419-040 87-A21-401-040 87-A21-415-010 8A-NF9-601-010 IC,STK490-040 C-IC,NJM14558MD-TE2 C-IC,M61503FP IC,LA1843 C-IC,UPD780226GF-012-3BA 87-A21-482-010 87-070-127-110 87-A21-269-010 IC,RPM6938-H4 IC,LC72131 D IC,EW732 TRANSISTOR KANRI NO. CAP, CAP, CAP, CAP, CAP, DESCRIPTION C31 C32 C34 C35 C36 87-010-263-080 87-010-197-080 87-010-260-080 87-010-379-080 87-010-381-080 ELECT 100-10V CHIP 0.01-25 ELECT 47-25V ELECT 22-16V ELECT 330-16V C38 C60 C61 C101 C102 87-010-197-080 87-010-403-080 87-010-260-080 87-010-183-080 87-010-183-080 CAP, CHIP 0.01-25 CAP, ELECT 3.3-50V CAP, ELECT 47-25V C-CAP,S 2700P-50 B C-CAP,S 2700P-50 B C103 C104 C107 C108 C109 87-010-545-080 87-010-545-080 87-010-406-080 87-010-406-080 87-012-157-080 CAP, ELECT 0.22-50V CAP, ELECT 0.22-50V CAP, ELECT 22-50 CAP, ELECT 22-50 C-CAP,S 330P-50 CH C110 C111 C112 C113 C114 87-012-157-080 87-010-405-080 87-010-405-080 87-010-405-080 87-010-405-080 C-CAP,S 330P-50 CH CAP, ELECT 10-50V CAP, ELECT 10-50V CAP, ELECT 10-50V CAP, ELECT 10-50V C119 C120 C123 C124 C125 87-010-197-080 87-010-197-080 87-010-176-080 87-010-176-080 87-012-368-080 CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 C-CAP,S 680P-50 SL C-CAP,S 680P-50 SL C-CAP,S 0.1-50 F C126 C127 C128 C129 C130 87-012-368-080 87-012-368-080 87-012-368-080 87-010-191-080 87-010-191-080 C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C131 C132 C133 C140 C141 87-010-197-080 87-010-197-080 87-010-186-080 87-010-182-080 87-012-368-080 CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 CAP,CHIP 4700P-50 C-CAP,S 2200P-50 B C-CAP,S 0.1-50 F C203 C204 C209 C210 C211 87-010-185-080 87-010-185-080 87-010-402-080 87-010-402-080 87-010-186-080 C-CAP,S 3900P-50 B C-CAP,S 3900P-50 B CAP, ELECT 2.2-50V CAP, ELECT 2.2-50V CAP,CHIP 4700P-50 C212 C213 C214 C217 C218 87-010-186-080 87-010-401-080 87-010-401-080 87-010-405-080 87-010-405-080 CAP,CHIP 4700P-50 CAP, ELECT 1-50V CAP, ELECT 1-50V CAP, ELECT 10-50V CAP, ELECT 10-50V C223 C224 C229 C230 C231 87-010-190-080 87-010-190-080 87-010-196-080 87-010-196-080 87-010-196-080 C-CAP,S 0.01-50 C-CAP,S 0.01-50 C-CAP,S 0.1-25 C-CAP,S 0.1-25 CHIP CAPACITOR,0.1-25 C232 C233 C234 C239 C270 87-010-196-080 87-010-190-080 87-010-190-080 87-010-196-080 87-010-190-080 CHIP CAPACITOR,0.1-25 C-CAP,S 0.01-50 C-CAP,S 0.01-50 CHIP CAPACITOR,0.1-25 C-CAP,S 0.01-50 C301 C302 C303 C304 C307 87-010-178-080 87-010-178-080 87-010-178-080 87-010-178-080 87-010-263-080 CHIP CHIP CHIP CHIP CAP, 87-026-609-080 89-213-702-010 87-026-610-080 87-A30-076-080 87-A30-075-080 TR,KTA1266GR TR,2SB1370E TR,KTC3198GR C-TR,2SC3052F C-TR,2SA1235F 87-026-245-080 87-A30-198-080 87-A30-074-080 87-A30-468-080 87-A30-107-070 TR,DTC114ES TR,KTC3199GR C-TR,RT1P 141C C-TR,KRC102S-RTK C-TR,CMBT5401 87-A30-106-040 87-A30-087-080 87-A30-091-080 87-A30-090-080 87-A30-062-080 C-TR,CMBT5551 C-FET,2SK2158 FET,2SJ460 FET,2SK2541 C-TR,KRC104S 87-A30-318-080 89-333-317-880 87-A30-269-040 87-A30-329-080 89-327-143-080 TR,CSA952K TR,2SC3331 (T/U) C-FET,2SJ461-T1 TR,CD1585BC TR,2SC2714O 87-A30-072-080 87-A30-086-070 89-503-602-080 87-A30-234-080 C-TR,RT1P 144C C-TR,CSD1306E C-FET,2SK360E TR,CSC4115BC 87-A40-393-090 87-A40-838-090 87-A40-553-080 87-A40-776-080 87-020-465-080 DIODE,1N5402GW(F20) DIODE,G3SBA60L-6088 DIODE,1N4003 LES ZENER,UZ27BSD DIODE,1SS133 87-A40-764-080 87-A40-313-080 87-A40-270-080 87-A40-269-080 87-A40-854-080 ZENER,UZ10BSC C-DIODE,MC2840 C-DIODE,MC2838 C-DIODE,MC2836 ZENER,UZ15BSA 87-A40-752-080 87-A40-739-080 87-017-149-080 ZENER,UZ6.2BSC ZENER,UZ2.7BSA ZENER,HZS6A2L C3 C4 C5 C6 C15 87-012-368-080 87-012-368-080 87-012-368-080 87-012-368-080 87-012-368-080 C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C16 C17 C18 C19 C20 87-012-368-080 87-012-368-080 87-012-368-080 87-010-917-000 87-010-917-000 C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F CAP,E 3300-50 M SMG CAP,E 3300-50 M SMG C308 C309 C310 C313 C314 87-010-263-080 87-010-318-080 87-010-318-080 87-010-188-080 87-010-188-080 CAP, ELECT 100-10V C-CAP,S 47P-50 CH C-CAP,S 47P-50 CH CAP,CHIP 6800P-50 CAP,CHIP 6800P-50 C23 C24 C25 C26 C30 87-016-495-000 87-016-495-000 87-010-408-080 87-010-247-080 87-010-430-080 CAP,E 3300-25 M SMG CAP,E 3300-25 M SMG CAP, ELECT 47-50V CAP, ELECT 100-50V CAP, ELECT 100-63 C315 C317 C318 C326 C327 87-010-263-080 87-010-546-080 87-010-546-080 87-010-198-080 87-012-368-080 CAP, ELECT 100-10V CAP, ELECT 0.33-50V CAP, ELECT 0.33-50V CAP, CHIP 0.022-25 C-CAP,S 0.1-50 F DIODE MAIN C.B 0.1-50 0.1-50 0.1-50 0.1-50 0.1-50 F F F F F –6– 0.1-50 F 0.1-50 F 0.1-50 F 0.015-50 F 0.015-50 F CAP,1000P-50 CAP,1000P-50 CAP,1000P-50 CAP,1000P-50 ELECT 100-10V REF. NO. PART NO. KANRI DESCRIPTION NO. CAP, ELECT 1-50V CAP, CHIP 0.01-25 C-CAP,S 470P-50 CAP, ELECT 0.1-50V CAP, ELECT 0.1-50V REF. NO. PART NO. KANRI DESCRIPTION NO. CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 C-CAP,S 5P-50 CH C-CAP,S 0.022-16 J B C784 C785 C786 C788 C789 87-010-197-080 87-010-197-080 87-010-197-080 87-010-149-080 87-A10-801-080 C790 C791 C792 C793 C795 87-A10-801-080 87-010-196-080 87-010-197-080 87-010-404-080 87-010-197-080 C-CAP,S 0.022-16 J B CHIP CAPACITOR,0.1-25 CAP, CHIP 0.01-25 CAP, ELECT 4.7-50V CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 C-CAP,S 2200P-50 B C-CAP,S 2200P-50 B CAP, ELECT 10-50V CAP, ELECT 10-50V C796 C797 C798 C799 C800 87-010-197-080 87-010-405-080 87-010-197-080 87-010-407-080 87-012-369-080 CAP, CHIP 0.01-25 CAP, ELECT 10-50V CAP, CHIP 0.01-25 CAP, ELECT 33-50V C-CAP,S 0.047-50F 87-010-382-080 87-010-183-080 87-010-183-080 87-010-183-080 87-010-197-080 CAP, ELECT 22-25V C-CAP,S 2700P-50 B C-CAP,S 2700P-50 B C-CAP,S 2700P-50 B CAP, CHIP 0.01-25 C801 C802 C803 C804 C807 87-010-403-080 87-010-194-080 87-010-198-080 87-010-263-080 87-010-400-080 CAP, CAP, CAP, CAP, CAP, ELECT 3.3-50V CHIP 0.047-25 CHIP 0.022-25 ELECT 100-10V ELECT 0.47-50V C458 C459 C460 C461 C462 87-010-178-080 87-010-175-080 87-010-196-080 87-012-158-080 87-012-158-080 CHIP CAP,1000P-50 C-CAP,S 560P-50 CHIP CAPACITOR,0.1-25 C-CAP,S 390P-50 CH C-CAP,S 390P-50 CH C808 C809 C810 C814 C815 87-010-401-080 87-010-401-080 87-010-196-080 87-010-197-080 87-010-400-080 CAP, CAP, CHIP CAP, CAP, ELECT 1-50V ELECT 1-50V CAPACITOR,0.1-25 CHIP 0.01-25 ELECT 0.47-50V C507 C508 C509 C510 C515 87-010-196-080 87-010-178-080 87-A10-300-080 87-A10-300-080 87-A10-300-080 CHIP CAPACITOR,0.1-25 CHIP CAP,1000P-50 CAP,M 0.027-50 J CAP,M 0.027-50 J CAP,M 0.027-50 J C816 C818 C821 C823 C824 87-010-400-080 87-010-180-080 87-010-405-080 87-012-349-080 87-010-405-080 CAP, ELECT 0.47-50V C-CER 1500P-50 CAP, ELECT 10-50V C-CAP,S 1000P-50 CH CAP, ELECT 10-50V C516 C518 C519 C520 C521 87-A10-300-080 87-010-196-080 87-010-401-080 87-010-401-080 87-010-546-080 CAP,M 0.027-50 J CHIP CAPACITOR,0.1-25 CAP, ELECT 1-50V CAP, ELECT 1-50V CAP, ELECT 0.33-50V C825 C831 C842 C844 C850 87-010-596-080 87-010-406-080 87-010-197-080 87-010-197-080 87-010-260-080 C-CAP, S 0.047-16 CAP, ELECT 22-50 CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 CAP, ELECT 47-25V C522 C523 C524 C525 C526 87-010-546-080 87-010-545-080 87-010-545-080 87-010-545-080 87-010-545-080 CAP, CAP, CAP, CAP, CAP, 0.33-50V 0.22-50V 0.22-50V 0.22-50V 0.22-50V C851 C852 C853 C858 C859 87-010-197-080 87-010-197-080 87-010-197-080 87-010-196-080 87-010-196-080 CAP, CAP, CAP, CHIP CHIP C605 C606 C609 C610 C611 87-010-179-080 87-010-179-080 87-010-213-080 87-010-213-080 87-010-545-080 CAP,CHIP S 1200P-50 CAP,CHIP S 1200P-50 C-CAP,S 0.015-50 B C-CAP,S 0.015-50 B CAP, ELECT 0.22-50V C860 C940 C942 C947 C948 87-010-197-080 87-010-197-080 87-010-149-080 87-010-197-080 87-012-140-080 CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 C-CAP,S 5P-50 CH CAP, CHIP 0.01-25 C-CAP,S 470P-50 C612 C613 C614 C615 C616 87-010-545-080 87-010-545-080 87-010-545-080 87-010-154-080 87-010-221-080 CAP, ELECT 0.22-50V CAP, ELECT 0.22-50V CAP, ELECT 0.22-50V C-CAP, S 10P-50 CAP, ELECT 470-10V C952 C957 C958 C959 C960 87-010-197-080 87-010-311-080 87-010-197-080 87-010-196-080 87-010-196-080 CAP, CHIP 0.01-25 C-CAP,S 12P-50 CAP, CHIP 0.01-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 C617 C618 C620 C630 C631 87-010-221-080 87-010-405-080 87-010-263-080 87-016-669-080 87-010-185-080 CAP, ELECT 470-10V CAP, ELECT 10-50V CAP, ELECT 100-10V C-CAP,S 0.1-25 K B C-CAP,S 3900P-50 B C962 C963 C971 C972 C973 87-010-401-080 87-015-785-080 87-010-381-080 87-010-404-080 87-010-197-080 CAP, CHIP CAP, CAP, CAP, C632 C633 C634 C661 C662 87-010-185-080 87-016-369-080 87-016-369-080 87-012-157-080 87-012-157-080 C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C974 C979 C981 C982 C983 87-010-197-080 87-010-322-080 87-010-260-080 87-010-196-080 87-010-197-080 CAP, CHIP 0.01-25 C-CAP,S 100P-50 CH CAP, ELECT 47-25V CHIP CAPACITOR,0.1-25 CAP, CHIP 0.01-25 C669 C670 C677 C678 C771 87-010-180-080 87-010-180-080 87-010-197-080 87-010-197-080 87-010-263-080 C-CAP,1500P-50 C-CAP,1500P-50 CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 CAP, ELECT 100-10V C984 C985 C987 C989 C991 87-010-197-080 87-010-322-080 87-010-197-080 87-010-197-080 87-010-312-080 CAP, CHIP 0.01-25 C-CAP,S 100P-50 CH CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 C-CAP,S 15P-50 CH C772 C779 C780 C782 C783 87-010-197-080 87-010-971-080 87-010-971-080 87-010-197-080 87-010-197-080 CAP, CHIP 0.01-25 C-CAP,S 4700P-50 B J C-CAP,S 4700P-50 B J CAP, CHIP 0.01-25 CAP, CHIP 0.01-25 C992 C993 C995 C997 C998 87-010-312-080 87-010-178-080 87-010-178-080 87-010-196-080 87-010-260-080 C-CAP,S 15P-50 CH CHIP CAP,1000P-50 CHIP CAP,1000P-50 CHIP CAPACITOR,0.1-25 CAP, ELECT 47-25V C360 C365 C399 C401 C402 87-010-401-080 87-010-197-080 87-012-140-080 87-010-544-080 87-010-544-080 C403 C404 C405 C406 C407 87-010-321-080 87-010-321-080 87-010-197-080 87-010-197-080 87-010-197-080 CHIP CHIP CAP, CAP, CAP, C408 C409 C410 C411 C412 87-010-197-080 87-010-182-080 87-010-182-080 87-010-405-080 87-010-405-080 C452 C453 C454 C455 C456 CAPACITOR,82P-50 CAPACITOR,82P-50 CHIP 0.01-25 CHIP 0.01-25 CHIP 0.01-25 ELECT ELECT ELECT ELECT ELECT 3900P-50 B 0.033-25 B K 0.033-25 B K 330P-50 CH 330P-50 CH –7– CHIP 0.01-25 CHIP 0.01-25 CHIP 0.01-25 CAPACITOR,0.1-25 CAPACITOR,0.1-25 ELECT 1-50V CAPACITOR, 0.1FZ-25Z ELECT 330-16V ELECT 4.7-50V CHIP 0.01-25 REF. NO. PART NO. KANRI DESCRIPTION NO. CAP,TC U 0.01-16 Z F CERAMIC FILTER, SFE10.7 CF,MS2 GHY,R CONN,3P V 2MM JMT CONN,8P V 2MM JMT REF. NO. PART NO. KANRI NO. C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S DESCRIPTION C902 C903 C904 C905 C906 87-010-322-080 87-010-322-080 87-010-322-080 87-010-322-080 87-010-322-080 CONN,30P TYK-B(X) CONN,6P V FE CONN ASSY,11P TID-A(480) F-BEAD,EMI BL02RN1 F-BEAD,EMI BL02RN1 C907 C908 C909 C910 C911 87-010-322-080 87-010-322-080 87-010-322-080 87-010-322-080 87-010-178-080 C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH CHIP CAP 1000P-50 A8-6ZA-19C-170 87-A60-483-010 87-A60-238-010 87-A61-157-010 87-A60-881-010 6ZA-1 YFEENC JACK,DIA6.3 BLK ST W/S KM TERMINAL,SP 4P (MSC) JACK,PIN 2P R/W/BL V(SEPA) KM JACK,PIN 2P MSP 242V05 PBSN C912 C913 C914 C915 C916 87-010-196-080 87-010-248-040 87-010-248-040 87-010-196-080 87-010-196-080 CHIP CAPACITOR,0.1-25 CAP,E 220-10 SME CAP,E 220-10 SME CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 J832 L101 L102 L201 L202 87-A60-403-010 87-A50-610-010 87-A50-610-010 87-A50-610-010 87-A50-610-010 TERMINAL,ANT PAL 2P HSP-312V05 COIL,1UH K(MDEC) COIL,1UH K(MDEC) COIL,1UH K(MDEC) COIL,1UH K(MDEC) C917 C919 C920 C921 C951 87-010-196-080 87-010-197-080 87-012-369-080 87-010-186-080 87-010-312-080 CHIP CAPACITOR,0.1-25 CAP, CHIP 0.01-25 C-CAP,S 0.047-50F CAP,CHIP 4700P-50 C-CAP,S 15P-50 CH L451 L801 L802 L811 L832 87-007-342-010 87-A50-540-010 87-A91-551-010 87-005-847-080 87-005-847-080 COIL,OSC 85K BIAS COIL,FM DET (TOK) FLTR,PCFJZH-450 L(TOK) COIL,2.2UH(CECS) COIL,2.2UH(CECS) C952 C953 C961 C962 C963 87-012-155-080 87-012-140-080 87-010-378-040 87-012-157-080 87-010-196-080 C-CAP 180P-50CH CAP 470P CAP,E 10-16 C-CAP,S 330P-50 CH CHIP CAPACITOR,0.1-25 L941 L942 L951 R129 R130 87-A50-020-010 87-A50-019-010 8A-NF8-668-010 87-A00-258-080 87-A00-258-080 COIL,ANT LW(COI) 252KHZ COIL,OSC LW(COI) 856KHZ COIL,AM PACK 2(TOK) RES,M/F 0.22-1W J RES,M/F 0.22-1W J CN104 CN701 CN731 FL901 L951 87-A60-057-010 87-099-720-010 87-099-015-010 8A-NF9-605-010 87-A50-434-010 CONN,11P V 9604S-11C CONN,30P TYK-B(P) CONN,13P 6216V FL,HNA-10SS12 COIL,CLK 4.19M(TOKO) R143 R144 R145 R146 R233 87-A00-439-050 87-A00-439-050 87-A00-439-050 87-A00-439-050 87-A00-258-080 RES,180-1/2W J RP RES,180-1/2W J RP RES,180-1/2W J RP RES,180-1/2W J RP RES,M/F 0.22-1W J LED201 LED202 LED204 LED205 LED209 87-A40-619-040 87-A40-619-040 87-A40-619-040 87-A40-619-040 87-A40-317-080 LED,SLR-56PT-T31-W GRN LED,SLR-56PT-T31-W GRN LED,SLR-56PT-T31-W GRN LED,SLR-56PT-T31-W GRN LED,SLR-342VCT31 RED R234 R790 R991 R993 R995 87-A00-258-080 87-010-197-080 87-010-322-080 87-010-322-080 87-010-322-080 RES,M/F 0.22-1W J CAP, CHIP 0.01-25 C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH LED210 S301 S302 S303 S304 87-A40-619-040 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 LED,SLR-56PT-T31-W GRN SW,TACT SKQAB(N) SW,TACT SKQAB(N) SW,TACT SKQAB(N) SW,TACT SKQAB(N) SFR451 SFR452 TC942 WH1 X991 87-A90-432-080 87-A90-432-080 87-011-253-080 87-A91-179-010 87-A70-061-010 SFR,30K H NVZ6TLTA SFR,30K H NVZ6TLTA TRIMER,30P LAR HLDR,WIRE 2.5-11P VIB,XTAL 4.500MHZ CSA-309 S305 S306 S307 S308 S309 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SKQAB(N) SKQAB(N) SKQAB(N) SKQAB(N) SKQAB(N) S321 S322 S323 S324 S325 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SKQAB(N) SKQAB(N) SKQAB(N) SKQAB(N) SKQAB(N) S326 S341 S342 S343 S344 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SKQAB(N) SKQAB(N) SKQAB(N) SKQAB(N) SKQAB(N) S345 S346 S347 S348 S349 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A90-164-080 SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SKQAB(N) SKQAB(N) SKQAB(N) SKQAB(N) SKQAB(N) S350 S361 S371 87-A90-164-080 87-A91-633-010 87-A91-632-010 SW,TACT SKQAB(N) SW,RTRY XRE012103PVB25FINA 1-2 SW,RTRY XRE012103PVB25FINB 1-2 87-010-387-080 87-A11-148-080 87-010-403-040 87-A61-122-010 CAP,E 470-25 SME CAP,TC U 0.1-50 Z F CAP,E 3.3-50 SME CONN,11P V TID-A C999 CF831 CF832 CN301 CN351 87-A11-155-080 87-008-423-010 82-785-747-010 87-A60-620-010 87-A60-625-010 CN601 CN602 CNA1 FB301 FB303 87-099-719-010 87-A60-131-010 8A-NF8-654-010 87-008-474-080 87-008-474-080 FFE831 J202 J203 J205 J602 FRONT C.B C101 C102 C103 C104 C107 87-010-196-080 87-010-196-080 87-010-498-040 87-010-196-080 87-010-493-040 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP,E 10-16 GAS CHIP CAPACITOR,0.1-25 CAP,E 0.47-50 GAS C108 C153 C154 C155 C156 87-012-393-080 87-010-198-080 87-010-246-040 87-010-404-040 87-010-404-040 C-CAP,S 0.22-16 R K CAP, CHIP 0.022-25 CAP,E 47-35 SME CAP,E 4.7-50 SME CAP,E 4.7-50 SME C361 C362 C371 C372 C601 87-010-178-080 87-010-178-080 87-010-178-080 87-010-178-080 87-010-382-040 CHIP CAP 1000P-50 CHIP CAP 1000P-50 CHIP CAP 1000P-50 CHIP CAP 1000P-50 CAP,E 22-25 SME C801 C802 C803 C804 C805 87-010-195-080 87-010-195-080 87-010-402-040 87-010-402-040 87-010-196-080 C-CAP,S 0.068-25 F C-CAP,S 0.068-25 F CAP,E 2.2-50 SME CAP,E 2.2-50 SME CHIP CAPACITOR,0.1-25 C806 C901 87-010-196-080 87-010-322-080 CHIP CAPACITOR,0.1-25 C-CAP,S 100P-50 CH 100P-50 100P-50 100P-50 100P-50 100P-50 CH CH CH CH CH PT C.B C1 C2 C184 CN1 –8– REF. NO. PART NO. ! ! ! ! ! PT1 PT2 RY2 T1 T2 8A-NFK-617-010 8A-NF8-662-010 87-A91-418-010 87-A60-317-010 87-A60-317-010 REF. NO. PART NO. KANRI DESCRIPTION NO. PT,ANF-19 EZ PT,SUB ANF-8 (E) RELAY,AC12V G5PA-1-M TERMINAL, 1P MSC TERMINAL, 1P MSC KANRI NO. DESCRIPTION DECK C.B CN1 SFR1 SW1 SW2 SW3 87-009-753-010 87-024-581-010 87-A90-673-010 87-A91-500-010 87-A91-500-010 CONN,11P SFR,3.3K SW,MICRO SW,MICRO SW,MICRO H 9604 DIA6V K0A ESE11SH1C MPU11470MLB0 MPU11470MLB0 SW4 SW5 87-A91-500-010 87-A90-673-010 SW,MICRO MPU11470MLB0 SW,MICRO ESE11SH1C CHIP RESISTOR PART CODE Chip Resistor Part Coding 8 8 A Figure Resistor Code Value of resistor Chip resistor Dimensions (mm) Wattage 1/16W Type 1005 Tolerance 5% Symbol CJ 1/16W 1/10W 1608 2125 5% 5% CJ CJ 1/8W 3216 5% CJ Form L t W –9– :A Resistor Code : A L W t 1.0 0.5 0.35 104 1.6 0.8 0.45 108 2 1.25 0.45 118 3.2 1.6 0.55 128 TRANSISTOR ILLUSTRATION E C B CD1585BC CSA952K CSC4115 KTA1266 KTC3198 E C B B C E 2SC3331 2SB1370 E C B DTC114ES KTC3199 C D D B G G E S S S D G 2SJ460 2SK2541 2SK2158 2SJ461-T1 2SA1235 2SC2714 2SC3052 CMBT5401 CMBT5551 – 10 – CSD1306 KRC102S KRC104S RT1P141C RT1P144C 2SK360 WIRING - 1 (MAIN) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U – 11 – SCHEMATIC DIAGRAM - 1 (MAIN 1/2: FUNCTION / AMPLIFIER) – 12 – SCHEMATIC DIAGRAM - 2 (MAIN 2/2: TUNER) – 13 – WIRING - 2 (FRONT) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U – 14 – SCHEMATIC DIAGRAM - 3 (FRONT) – 15 – WIRING – 3 (PT) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U – 16 – SCHEMATIC DIAGRAM - 4 (PT) CNA1 – 17 – WIRING - 4 (DECK) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A D DECK C.B B C D E F G H I J K L M N O P Q R S T U – 18 – FL (HNA-10SS12) GRID ASSIGNMENT AND ANODE CONNECTION GRID ASSIGNMENT ANODE CONNECTION – 19 – IC BLOCK DIAGRAM IC, LC72131D IC, M61503FP – 20 – IC, LA1843 – 21 – IC DESCRIPTION IC, µPD780226GF-012-3BA Pin Name Pin No. I/O Description 1 O-MOTOR O DECK MOTOR ON/OFF output. 2 O-SOL1 O DECK1 solenoid output. 3 O-SOL2 O DECK2 solenoid output. 4 O-P-LOGIC_LED – Not connected. 5 O-RVS_LED – Not connected. 6 O-SET_LED O SET LED ON/OFF output. 7 O-CLEAR_LED O CLEAR LED ON/OFF output. 8 O-PRESET_LED O PRESET LED ON/OFF output. 9 O-DOWN_LED O DOWN LED ON/OFF output. 10 O-UP_LED O UP LED ON/OFF output. 11 O-TUNER_ON O TUNER ON output. 12 O-MUTE O MUTE output. 13 O-PB2 O DECK2/DECK1 play output. 14 O-BIAS O BIAS ON output. 15 O-RMT O REC mute output. 16 O-CD_ON O CD ON output. 17 IC – Internal connection (connected to GND). 18 VSSO – GND. 19 VDDO – Power supply. 20 O-POWER O System power supply ON/OFF output. 21 O-CD_OPEN O CD tray open data output. 22 O-CD_CLOSE O CD tray close data output. 23 O-CD_DISH_F O CD turntable forward rotation output. 24 O-CD_DISH_R O CD turntable reverse rotation output. 25 IO-BUSY – Not connected. 26 O-STB(M) – Not connected. 27 I-REA I Volume jog AD input. 28 I-RDS_CLK I Tuner RDS clock input (Not used). 29 I-SUBQ/I-RDS_DATA I CD SUBQ data input / Tuner RDS data input (Not used). 30 RESET – System reset. 31 O-DATA O Data output for MAIN. 32 I-WRQ/STEREO I CD WRQ input / Tuner stereo input. 33 I-DRF/IFC I CD DRF input / Tune IF count serial data input. 34 I-RMC I System remote control input. 35 I-DISHSENS I CD turntable photo sensor input. 36 O-CLK_SFT O Micon clock shift output. 37 VDD1 – Power supply. 38 X2 – 4.19MHz oscillator circuit. 39 X1 – 4.19MHz oscillator circuit. 40 VSS1 – GND. 41 AVDD – Power supply. 42 I-HOLD I Power failure detected input. 43 I-CDSW I CD mecha switch input. – 22 – Pin No. Pin Name I/O Description 44 I-SPEANA_L I A/D L-input for spectrum analyser level display. 45 I-SPEANA_R I A/D R-input for spectrum analyser level display. 46 I-KEY1 I Key1 input. 47 I-KEY2 I Key2 input. 48 I-KEY3 I Key3 input. 49 I-TU_SIG I Tuner signal input (Not used). 50 AVSS – GND. 51 O-PLL_CLK O PLL clock enable output. 52 O-PLL_CE O Chip enable output for tuner PLL. 53 O-CD_LED O CD flash window LED ON/OFF output. 54 O-KSCAN O Key scan output. 55 O-CD_CLK O CD clock output. 56 O-CD_DATA O CD data output. 57 O-CD_CE O CD enable output. 58 NC – Not connected. 59 I-JOG_B I Dial jog rotary encoder input B. 60 I-JOG_A I Dial jog rotary encoder input A. 61 I-VOL_B I Volume rotary encoder input B. 62 I-VOL_A I Volume rotary encoder input A. 63 I-REB – Not connected. 64 I-TM_BASE I Base input for clock. 65 I-CAM2 I DECK2 CAM switch data input. 66 I-CAM1 I DECK1 CAM STOP switch data input. 67 P1/I-AUTO2 O/I FL segment P1 output / DECK2 AUTO STOP switch data input. 68 P2/I-AUTO1 O/I FL segment P2 output / DECK1 AUTO STOP switch data input. 69 P3/I-CST2 O/I FL segment P3 output / DECK2 cassette detect switch data input. 70 P4/I-CST1 O/I FL segment P4 output / DECK1 cassette detect switch data input. 71 P5/AM10K O/I FL segment P5 output / AM10K data input (Not used). 72 ~ 78 P6 ~ P12 O FL segment P6 ~ P12 output. 79 VDD2 – Power supply. 80 VLOAD – Power supply for FL display. 81 P13/C-JACK O/I FL segment P13 output / C-JACK data input (Not used). 82 P14/ECO-OFF O/I FL segment P14 output / ECO-OFF data input (Not used). 83 ~ 90 P15 ~ P22 O FL segment P15 ~ P22 output. 91 ~100 G1 ~ G10 O FL grid G1 ~ G10 output. – 23 – ADJUSTMENT <TUNER / DECK> A MAIN C.B 16 15 14 13 12 11 8 7 6 5 1 3 6 L941 TC942 L942 L802 L801 15 9 8 9 6 L951 TP4 (DC BAL) IC801 24 SFR 451 SFR 452 (RCH) (LCH) IC301 5 TP3 (DC BAL) TP2 (CLK) (3/3) (1/3) 3 TP8 (LCH) TP1(VT) TP-OUT (GND) FFE831 TP9 (RCH) 2 3 4 B FRONT C.B FL901 IC901 TP10 L951 GND 10 10 10 DECK–1 P HEAD DECK–2 R/P/E HEAD D DECK C.B FWD SFR1 12 11 – 24 – REV 12 < TUNER SECTION > < FRONT SECTION > 1. Clock frequency Check Settings : • Test point : TP2 (CLK) Method : Set to MW 1602kHz and check that the test point is 2052kHz ± 45Hz. 10. µ-CON OSC Adjustment Settings : • Test point : TP10 and GND • Adjustment location : L951 Method : Insert AC plug with pressing of DISPLAY key. Adjust L951 so that the frequency across the test point is 184.94Hz ± 0.18Hz. 2. MW VT Check Settings : • Test point : TP1 (VT) Method : Set to MW 1602kHz, 531kHz and check that the test point is less than 8.0V (1602kHz) and more than 0.6V (531kHz). <DECK SECTION > 3. LW VT Adjustment Settings : • Test point : TP1(VT) • Adjustment location : L942 ............................................... 144 kHz TC942 ............................................ 290 kHz Method : Set to LW 144 kHz and adjust L942 so that the test point becomes 1.3V ± 0.05V. Then set to LW 290 kHz and check that the test point is less than 8.0V. 4. FM VT Check Settings : • Test point : TP1 (VT) Method : Set to FM 87.5MHz, 108.0MHz and check that the test point is more than 0.5V (87.5MHz) and less than 8.0V (108.0MHz). 5. MW Tracking Adjustment Settings : • Test point : TP8(Lch), TP9(Rch) • Adjustment location : L951(1/3) ....................................... 999 kHz Method : Set to MW 999 kHz and adjust L951(1/3) to MAX. 6. LW Tracking Adjustment Settings : • Test point : TP8(Lch), TP9(Rch) • Adjustment location : L941 ............................................... 144 kHz TC942 ............................................ 290 kHz Method : Set up TC942 to center before adjustment. The level at 144 kHz is adjusted to MAX by L941. Then the level at 290 kHz is adjusted to MAX by TC942. 7. FM Tracking Check Settings : • Test point : TP8(Lch), TP9(Rch) Method : Set to FM 98.0MHz and check that the test point is less than 13dBµV. 8. AM IF Adjustment Settings : • Test point : TP8(Lch), TP9(Rch) • Adjustment location : L802 ............................................... 999 kHz Method : Set to AM 98.0MHz and adjust L802 so that the output at the test point becomes maximum. 9. DC Balance / Mono Distortion Adjustment Settings : • Test point : TP3, TP4 (DC Balance) • Adjustment location : L801 • Input level : 60dBµV Method : Set to FM 98.0MHz and adjust L801 so that the voltage between TP3 and TP4 becomes 0V ± 300mV. Next, check that the distortion is less than 1.3%. 11. Tape Speed Adjustment (DECK 2) Settings : • Test tape : TTA–100 • Test point : TP8(Lch), TP9(Rch) • Adjustment location : SFR1 Method : Play back the test tape and adjust SFR1 so that the frequency counter reads 3000Hz ± 5Hz and ± 45Hz (REV) with respect to forward speed. 12. Head Azimuth Adjustment (DECK 1, DECK 2) Settings : • Test tape : TTA–330 • Test point : TP8(Lch), TP9(Rch) • Adjustment location : Head azimuth adjustment screw Method : Play back (FWD) the 8kHz signal of the test tape and adjust screw so that the output becomes maximum. Next, perform on REV PLAY mode. 13. PB Frequency Response Check (DECK 1, DECK 2) Settings : • Test tape : TTA–330 • Test point :TP8(Lch), TP9(Rch) Method : Play back the 315Hz and 8kHz signals of the test tape and check that the output ratio of the 8kHz signal with respect to that of the 315Hz signal is within 5dB. 14. PB Sensitivity Check (DECK 1, DECK 2) Settings : • Test tape : TTA–200 • Test point : TP8(Lch), TP9(Rch) Method : Play back the test tape and check that the output level of the test point is 110mV ± 3dB. 15. REC/PB Frequency Response Adjustment (DECK 2) Settings : • Test tape : TTA–602 • Test point : TP8(Lch), TP9(Rch) • Input signal : 1kHz / 8kHz (LINE IN) • Adjustment location : SFR451 (Lch) SFR452 (Rch) Method : Apply a 1kHz signal and REC mode. Then adjust OSC attenuator so that the output level at the TP8, TP9 becomes -20VU. Record and play back the 1kHz and 8kHz signals and adjust SFRs so that the output of the 8kHz signals becomes 0dB ± 0.5dB with respect to that of the 1kHz signal. 16. REC/PB Sensitivity Check (DECK 2) Settings : • Test tape : TTA–602 • Test point : TP8(Lch), TP9(Rch) • Input signal : 1kHz (LINE IN) Method : Apply a 1kHz signal and REC mode. Then adjust OSC attenuator so that the output level at TP8, TP9 becomes 0VU. Record and play back the 1kHz signals and check that the output is -1dB ± 3.5dB. – 25 – MECHANICAL EXPLODED VIEW 1 / 1 44 A AZG-1 A A A P.C.B 19 WIRE,BINDER C 31 A B A 20 A 18 29 G 30 17 21 12 B FL901 22 A 24 16 A HT-SINK A P.C.B I 25 H PLATE,SHLD PT 2T 9 33 E P.C.B 34 39 45 7 5 43 H 28 23 15 G 32 40 I A 27 8 F 26 3 A 9 6 A 35 1 14 13 36 37 A D CHAS,MAIN 11 2 4 PLATE,EARTH MECH 37 36 38 41 ZZM-3 42 10 G – 26 – MECHANICAL PARTS LIST 1 / 1 KANRI DESCRIPTION NO. 8A-NF9-006-010 WINDOW,CASS 1 8A-NF9-007-010 WINDOW,CASS 2 8A-NF9-003-010 BOX,CASS 1 8A-NF9-004-010 BOX,CASS 2 8A-NF8-207-010 SPR-T,EJECT 1 REF. NO. PART NO. 1 2 3 4 5 REF. NO. PART NO. 31 32 33 34 35 KANRI DESCRIPTION NO. 88-906-251-110 FF-CABLE,6P 1.25 8A-NF8-205-010 HLDR,IC 88-913-301-110 FF-CABLE,13P-1.25 88-911-101-110 FF-CABLE,11P 1.25 87-NF4-216-010 HLDR,LOCK 1 36 37 38 39 40 86-NF9-224-010 82-NF5-229-010 87-NF4-217-110 87-A80-092-010 87-085-185-010 SPR-C,LOCK PLATE,LOCK HLDR,LOCK 2 AC CORD ASSY,E BLK SUN FAI BUSHING, AC CORD (E) 41 42 43 44 45 8Z-NB8-240-010 8A-NF8-008-010 8A-NFK-002-010 84-ZG1-245-210 87-NF4-221-010 COVER, PL PANEL,RIGHT V-2 CABI,REAR EZSE CAP,OPTICAL HLDR,CABLE 6 7 8 9 10 8A-NF8-208-010 87-CE3-023-010 8A-NF9-016-010 8A-NF8-209-010 8A-NF9-017-010 SPR-T,EJECT 2 BADGE,AIWA 30N SILV KNOB,RTRY VOL OIL-DMPR,120 PANEL,JOG 11 12 13 14 15 8A-NF9-018-010 8A-DB8-209-010 81-532-080-010 8A-NFK-001-010 8A-NFK-003-010 KNOB,RTRY JOG HLDR,PWB PT LABEL, CASS. COMPT CABI,FR EZ WINDOW,DISP EZ 16 17 18 19 20 8A-NF9-039-010 8A-NF8-007-010 8A-NF8-005-010 8A-NF8-006-010 8A-NF9-014-010 WINDOW,CD PANEL,LEFT V-2 PANEL,TOP WINDOW,TOP PANEL,TRAY A B C D E 87-067-703-010 87-NF4-224-010 87-067-581-010 87-067-689-010 87-723-096-410 TAPPING SCREW, BVT2+3-10 S-SCREW,IT3B+3-8 CU TAPPING SCREW, BVT2+3-15 TAPPING SCREW, BVTT+3-8 QT2+3-10W/O SLOT BL 21 22 23 24 25 8A-NF9-008-010 8A-NF9-009-010 8A-NF9-022-010 8A-NF9-010-110 8A-NF9-020-010 KEY,POWER KEY,FUN REFLECTOR,ECO KEY,ASSY OPE 1 WAY KEY,CD F G H I 87-721-096-410 87-067-641-010 87-078-191-010 87-721-097-410 QT2+3-10 GLD UTT2+3-8(W/O SLOT)BL S-SCREW,IT+4-10 QT2+3-12 GLD 26 27 28 29 30 8A-NF9-019-010 8A-NF9-026-110 8A-NF9-201-010 82-NF7-210-110 8A-NF8-206-010 KEY,SYNC KEY,ENTER GUIDE,OPE 1 WAY GUIDE,FL (*) HLDR,PWB M ! COLOR NAME TABLE Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green YM Metallic Yellow DM Metallic Orange – 27 – TAPE MECHANISM EXPLODED VIEW 1 / 1 TERMINAL, LB1 33 A 34 55 A 44 45 43 36 42 31 32 41 46 51 TERMINAL,LB1 33 45 51 35 A 52 44 52 31 32 b a 29 43 47 29 40 39 28 48 50 42 53 46 49 35 41 30 27 37 21 47 B 38 a 48 40 19 27 49 20 26 25 b 24 56 23 18 16 22 28 30 21 26 20 25 24 19 IC, EW732 23 18 22 IC, EW732 54 9 5 6 38 1 14 54 39 2 10 11 c c 5 6 3 37 9 14 7 15 16 P.C.B 10 7 11 12 8 4 17 12 15 13 – 28 – 13 TAPE MECHANISM MAIN PARTS LIST 1 / 1 REF. NO. PART NO. REF. NO. PART NO. KANRI DESCRIPTION NO. BELT,MAIN M3 BELT,MAIN L PULLEY,MOT MOT,SHU2L 70 GEAR,IDL FF/REW KANRI DESCRIPTION NO. LEVER,EJECT R LEVER,STOP LEVER,CAS SPR-T,LVR CAS SPR-C,REEL R M3 36 37 38 39 40 8Z-ZM3-211-010 8Z-ZM3-225-010 8Z-ZM3-221-010 8Z-ZM3-234-010 8Z-ZM3-223-010 GEAR,CAM TD20 SHAFT,CAP M3 FLY-WHL,M3 SPR-T,TRIG CLR,MG 41 42 43 44 45 8Z-ZM1-225-110 8Z-ZM3-240-010 8Z-ZM3-237-010 8Z-ZM3-215-010 8Z-ZM1-261-110 GEAR,REEL R SPR-T,T-UP M3 SPR-T,PINCH M3 LEVER,PINCH M3 ROLLER ASSY,PINCH 82-ZM3-616-010 8Z-ZM3-243-010 8Z-ZM3-238-010 8Z-ZM3-219-010 8Z-ZM3-206-010 RING MAGNET 4 LEVER ASSY,HD UP SPR-T,HD UP GEAR,CAM M3 LEVER,TRIG 46 47 48 49 50 8Z-ZM1-226-010 8Z-ZM3-222-010 8Z-ZM3-251-010 8Z-ZM3-236-010 82-ZM1-240-110 GEAR,REEL L SPR-C,REEL L M3 GEAR,IDL REW M3 SPR-T,PLAY M3 LVR,REC(*) 16 17 18 19 20 8Z-ZM3-209-010 8Z-ZM2-211-010 8Z-ZM1-228-010 8Z-ZM1-265-010 8Z-ZM1-227-010 LEVER,CAM FR FLY-WHL,ZZM-2 GEAR,SLIP T-UP B FELT,T-UP GEAR,SLIP T-UP A 51 52 53 54 55 8Z-ZM3-216-010 87-B10-301-010 8Z-ZM3-212-010 8Z-ZM3-214-010 86-ZM3-605-110 LEVER,T-UP M3 W-L,1.63-3.2-05 SLIT LEVER,EJECT L HLDR,IC CONN ASSY,8P -RPB 21 22 23 24 25 8Z-ZM1-251-110 8Z-ZM1-275-010 8Z-ZM1-257-010 8Z-ZM1-236-010 8Z-ZM3-226-010 SPR-C,T-UP SLIP W-L,1,47-4-0.25 SPR-C,F/R CLR,SLIP FF/REW SPR-C,FR M3 56 A B 8Z-ZM3-203-010 84-ZM2-242-010 8Z-ZM2-220-110 CHAS ASSY,M3 S-SCREW,AZ1-2-6.4 V+2.6 ZZM-2 26 27 28 29 30 8Z-ZM3-250-010 8Z-ZM1-269-010 8Z-ZM1-238-110 8Z-ZM3-220-010 8Z-ZM3-205-010 GEAR,SLIP F/R A M3 FELT,FF/REW 2 GEAR,SLIP FF/REW B 2 LEVER,FR M3 LEVER,PLAY M3 31 32 33 34 35 8Z-ZM3-233-010 84-ZM2-227-310 87-A90-403-110 87-A90-404-010 8Z-ZM3-239-010 SPR-T,BRG M3 SPR-C,AZIMUTH HEAD,RPH MS15R HEAD,EH LE15B SPR-E,FR 1 2 3 4 5 8Z-ZM3-227-010 8Z-ZM3-235-010 8Z-ZM1-235-010 87-045-347-010 8Z-ZM1-232-010 6 7 8 9 10 8Z-ZM3-244-010 8Z-ZM3-242-010 8Z-ZM3-228-010 8Z-ZM3-231-010 8Z-ZM3-213-010 11 12 13 14 15 – 29 – SPEAKER DISASSEMBLY INSTRUCTIONS Type.1 Type.4 TOOLS Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units. 1 2 3 1 2 Plastic head hammer flat head screwdriver Cut chisel 3 How to Remove the PANEL, FR Type.2 Remove the grill frame and four pieces of rubber caps by pulling out with a flat-bladed screwdriver. Remove the screws from hole where installed rubber caps. Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units. 1. Insert the flat head screwdriver tip into the gap between the PANEL, FR and the PANEL, SPKR. Tap the head of the∏ flat head screwdriver with the plastic hammer head, and create the clearance as shown in Fig-1. 2. Insert the cut chisel in the clearance, and tap the head of the cut chisel with plastic hammer as shown in Fig-2, to remove the PANEL, FR. 3. Place the speaker horizontally. Tap head of the cut chisel with plastic hammer as shown in Fig-3, and remove the PANEL, FR completely. Type.3 Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into one of the hollows around speaker unit, and then remove the speaker unit. After replacing the speaker unit, install it turning to clockwise direction until "click" sound comes out. Fig-1 Fig-2 Fig-3 How to Attach the PANEL, FR Attach the PANEL, FR to the PANEL, SPKR. Tap the four corners of the PANEL, FR with the plastic hammer to fit the PANEL, FR into the PANEL, SPKR completely. – 30 – SPEAKER PARTS LIST (SX-WNSZ35<YSL>) REF. NO. PART NO. 1 2 3 4 5 KANRI DESCRIPTION NO. 8A-NS9-001-010 PANEL,FR 8A-NS9-004-010 GRILLE, FRAME ASSY 8A-NS9-602-010 SPKR,W 160 8Z-NSY-604-010 SPKR, M 100 88-NS5-610-010 CORD,SPKR 6 7 88-NS5-611-010 8A-NS9-610-010 REF. NO. PART NO. CORD,SPKR B/L SPKR,CERAMIC ACCESSORIES / PACKAGE LIST KANRI DESCRIPTION NO. 8A-NFK-906-010 IB,EZ (9L)E -SZ35 87-006-225-010 AM-LOOP ANT NC2 87-A90-118-010 ANT,WIRE FM (Z) 8Z-NF9-701-210 RC UNIT,ZAS02 REF. NO. PART NO. 1 2 3 4 – 31 – KANRI NO. DESCRIPTION 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9920594 0251431 Printed in Singapore
0
advertisement
Download
advertisement
Add this document to collection(s)
You can add this document to your study collection(s)
Sign in Available only to authorized usersAdd this document to saved
You can add this document to your saved list
Sign in Available only to authorized users