Data Sheet
SAFEGRID 35 Ball Proof
30mm x 5mm
GRATING
COMPOSITES
INSTALLATION
Product Specification:
35BP305AMS
Bar Surface
Serrated
Enhanced Slip Resistant
Slip Classification
0.6or more(CoF)
38mm
125mm
994mm
36.24kg/m²
S275JR
Self Colour or Galvanised
Load Bearing Bar Centres
Transverse Bar Centres
Standard Width
Weight
Material Grade
Finish
Loading Category
Max clear span
with a
4mm Deflection
Deflection
5kN/m²
1260mm
3.97mm
7.5kN/m²
1145mm
3.98mm
35 Ball Proof is intended to be used above an area where people occasionally pass, therefore the maximum opening shall
not permit the passage of a 35mm diameter sphere. This product has been designed in line with the British and European
standards to ensure where possible the safety of all personnel passing under the walkway or platform.
Please refer to document number LWK-TEC-S-055 for associated fixings.
Quality Assurance:
Business Information Modelling (BIM) compliant to ISO 19650
Certificate of Conformity as Standard
Declaration of Performance (DOP) for CE/UKCA marking
BS EN ISO 9001:2015 – Quality Management Systems
BS EN ISO 14001:2015 – Environmental Management Systems
BS EN ISO 45001:2018 – Health & Safety Management Systems
BS 4592-0:2012 – Flooring, Stair Treads and Handrail for Industrial Use (Design Requirements)
BS 4592-1:2006 – Industrial Type Flooring and Stair Treads (Open Bar Grating)
BS EN ISO 14122-1:2016 – Safety of Machinery (General Requirements)
BS EN ISO 14122-2:2016 – Safety of Machinery (Working platforms and Walkways)
Contact our Sales Department
sales@lk-uk.com +44 (0) 1642 233 299
Individual calculations sheet available upon request.
Contact our Technical Department
technical@lk-uk.com +44 (0) 1642 233 297
The weight is estimated based on a galvanized finish.
Advice and guidance is given in good faith without responsibility.
Calculation sheets must be used from either LK group or other suitably qualified engineering sources to confirm and determine the final max clear span and loading per attached typical data.
LWK-TEC-S-032
Rev-001
GRATING
GRATING
COMPOSITES
COMPOSITES
Data Sheet
SAFEGRID
Data Sheet
Terminology
SAFEGRID
Terminology
INSTALLATION
INSTALLATION
Width
1
Length
11
Length
3
2
1
3
2
4
4
4
3
5
Direction
of Span
6
6
Direction
of Span
7
2
7
Pitch
Pitch
8
5
1. TOE PLATE (KICK-PLATE)
5. PITCH
1. WIDTH
7. PITCH
A flat bar welded to a flooring panel
The distance centre-to-centre of load
The overall dimension
of aabove
flooring
load
projecting
the top of the The
loaddistance centre-to-centre
bearing bars or of
centre-to-centre
of
panel measured
perpendicular
to the
bearing bars ortransverse
centre-to-centre
bearing
bars.
bars. of
9
load bearing bars.
transverse bars.
2. LENGTH (DIRECTION OF SPAN)
6. TRANSVERSE BAR
2. NOSING BAR
8. TRANSVERSE
BAR fixed perpendicular to the
The overall dimension of a flooring
A member
A slip resistant panel
member
attached
to the
A member
perpendicular
to the
parallel
with the
load bearing
bars fixed
load
bearing bars.
front of a stair tread
or flooringispanel.
(this dimension
always referredload
to asbearing bars.
‘length’ even if it is shorter than the
7. LOAD BEARING BAR
3. END PLATEwidth).
9. LOAD BEARING
A loadBAR
bearing member spanning
A plate welded to a stair tread for fixing
A load bearingbetween
membersupports.
spanning
to a stringer. 3. BINDING BAR
between supports.
A bar or section fixed to the edge of a
8. CURB ANGLE
4. TOE PLATEflooring
(KICK-PLATE)
CURB ANGLE
panel flush with the top10.
of the
A rolled steel angle (RSA) fixed to
A flat bar welded
tobearing
a flooring
panel
A rolled steel angle
(RSA)
fixed to flooring.
load
bars.
concete
to support
projecting above the top of the load
concete to support flooring.
bearing bars. 4. BAR SURFACE
11. BAR SURFACE
There are two types of surface finish,
5. LENGTH (DIRECTION
OFvarying
SPAN) slip resistance
Theretoare two types of surface finish,
which provide
The overall dimension
of a flooring
which provide varying slip resistance to
the flooring:
panel parallel with
the-load
bearing
barscreatingthe
flooring:
PLAIN
A smooth
finish
a slip
(this dimensionresistance
is always referred
to as
PLAIN - A smooth finish creating a slip
to the flooring.
‘length’ even ifSERRATED
it is shorter than
the
to the flooring.
- A serration
formedresistance
in the
width).
SERRATED - A serration formed in the
top surface of the load bearing bars
giving enhanced slip resistance. top surface of the load bearing bars
6. BINDING BAR
giving enhanced slip resistance.
A bar or section fixed to the edge of a
flooring panel flush with the top of the
load bearing bars.
Contact our Sales Department sales@lk-uk.com +44 (0) 1642 233 299
5
Pitch
8
7
10
Contact our Technical Department technical@lk-uk.com +44 (0) 1642 233 297