Exercicios resolvidos Maquinas Eletricas

WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 1 PROBLEM SOLUTIONS: Chapter 1 Problem 1.1 Part (a): Rc = lc lc = =0 µAc µr µ0 Ac A/Wb Rg = g = 1.017 × 106 µ0 Ac A/Wb part (b): Φ= NI = 1.224 × 10−4 Rc + Rg Wb part (c): λ = N Φ = 1.016 × 10−2 Wb part (d): L= λ = 6.775 mH I Problem 1.2 part (a): Rc = lc lc = = 1.591 × 105 µAc µr µ0 Ac Rg = g = 1.017 × 106 µ0 Ac A/Wb A/Wb part (b): Φ= NI = 1.059 × 10−4 Rc + Rg Wb part (c): λ = N Φ = 8.787 × 10−3 part (d): L= λ = 5.858 mH I Wb WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 2 Problem 1.3 part (a): N= Lg = 110 turns µ0 Ac part (b): I= Bcore = 16.6 A µ0 N/g Problem 1.4 part (a): N= L(g + lc µ0 /µ) = µ0 Ac L(g + lc µ0 /(µr µ0 )) = 121 turns µ0 Ac part (b): I= Bcore = 18.2 A µ0 N/(g + lc µ0 /µ) Problem 1.5 part (a): part (b): 3499 µr = 1 + = 730 1 + 0.047(2.2)7.8 I=B g + µ0 lc /µ µ0 N = 65.8 A WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 3 part (c): Problem 1.6 part (a): Hg = NI ; 2g Bc = Ag Ac x Bg = Bg 1 − X0 part (b): Equations 2gHg + Hc lc = N I; Bg Ag = Bc Ac and Bg = µ0 Hg ; Bc = µHc can be combined to give     N I N I =  Bg =  Ag µ0 x (l (l 1 − + l ) + l ) 2g + µµ0 2g + c p c p Ac µ X0 Problem 1.7 part (a):  part (b): g+ I = B µ0 µ (lc + lp ) µ0 N   = 2.15 A 1199 µ = µ0 1 + √ = 1012 µ0 1 + 0.05B 8  I = B g+ µ0 µ (lc + lp ) µ0 N   = 3.02 A WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 4 part (c): Problem 1.8 g= µ0 N 2 Ac L − µ0 µ lc = 0.353 mm Problem 1.9 part (a): lc = 2π(Ro − Ri ) − g = 3.57 cm; Ac = (Ro − Ri )h = 1.2 cm2 part (b): Rg = g = 1.33 × 107 µ0 Ac A/Wb; Rc = 0 A/Wb; part (c): L= N2 = 0.319 mH Rg + Rg part (d): I= Bg (Rc + Rg )Ac = 33.1 A N part (e): λ = N Bg Ac = 10.5 mWb Problem 1.10 part (a): Same as Problem 1.9 part (b): Rg = g = 1.33 × 107 µ0 Ac A/Wb; Rc = lc = 3.16 × 105 µAc A/Wb WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 5 part (c): N2 = 0.311 mH Rg + Rg L= part (d): I= Bg (Rc + Rg )Ac = 33.8 A N part (e): Same as Problem 1.9. Problem 1.11 Minimum µr = 340. Problem 1.12 L= µ0 N 2 Ac g + lc /µr Problem 1.13 L= µ0 N 2 Ac = 30.5 mH g + lc /µr Problem 1.14 part (a): Vrms = ωN Ac Bpeak √ = 19.2 V rms 2 part (b): Irms = Vrms = 1.67 A rms; ωL √ Wpeak = 0.5L( 2 Irms )2 = 8.50 mJ WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 6 Problem 1.15 part (a): R3 = R12 + R22 = 4.27 cm part (b): L= µ0 Ag N 2 = 251 mH g + µµ0 lc part (c): For ω = 2π60 rad/sec and λpeak = N Ag Bpeak = 0.452 Wb: (i) (ii) (iii) Vrms = ωλpeak = 171 V rms Vrms = 1.81 A rms Irms = ωL √ Wpeak = 0.5L( 2Irms )2 = 0.817 J part (d): For ω = 2π50 rad/sec and λpeak = N Ag Bpeak = 0.452 Wb: (i) (ii) (iii) Problem 1.16 part (a): Vrms = ωλpeak = 142 V rms Vrms Irms = = 1.81 A rms ωL √ Wpeak = 0.5L( 2Irms )2 = 0.817 J WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 7 part (b): Emax = 4f N Ac Bpeak = 345 V Problem 1.17 part (a): N= LI = 99 turns; Ac Bsat g= µ0 N I µ0 lc = 0.36 mm − Bsat µ part (b): From Eq.3.21 Wgap = 2 Ac gBsat = 0.207 J; 2µ0 Wcore = 2 Ac lc Bsat = 0.045 J 2µ Thus Wtot = Wgap + Wcore = 0.252 J. From Eq. 1.47, (1/2)LI 2 = 0.252 J. Q.E.D. Problem 1.18 part (a): Minimum inductance = 4 mH, for which g = 0.0627 mm, N = 20 turns and Vrms = 6.78 V part (b): Maximum inductance = 144 mH, for which g = 4.99 mm, N = 1078 turns and Vrms = 224 V Problem 1.19 part (a): L= µ0 πa2 N 2 = 56.0 mH 2πr part (b): Core volume Vcore ≈ (2πr)πa2 = 40.0 m3 . Thus 2 B W = Vcore = 4.87 J 2µ0 part (c): For T = 30 sec, (2πrB)/(µ0 N ) di = = 2.92 × 103 dt T v=L A/sec di = 163 V dt Problem 1.20 part (a): Acu = fw ab; part (b): Volcu = 2ab(w + h + 2a) WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 8 B = µ0 Jcu Acu g part (c): Jcu = NI Acu part (d): 2 Pdiss = Volcu ρJcu part (e): Wmag = Volgap B2 2µ0 = gwh B2 2µ0 part (f): L = R 1 2 1 2 LI 2 = RI 2 2Wmag Wmag µ0 whA2cu = = 1 Pdiss ρgVolcu 2 Pdiss Problem 1.21 Using the equations of Problem 1.20 Pdiss = 115 W I = 3.24 A N = 687 turns R = 10.8 Ω τ = 6.18 msec Wire size = 23 AWG Problem 1.22 part (a): (i) (ii) (iii) B1 = µ0 N1 I1 ; g1 B2 = µ0 N1 I1 g2 µ0 N12 λ1 = N1 (A1 B1 + A2 B2 ) = A2 λ2 = N2 A2 B2 = µ0 N1 N2 I1 g2 A2 A1 + g1 g2 I1 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 9 part (b): (i) (ii) (iii) B1 = 0; B2 = µ0 N2 I2 g2 A2 λ1 = N1 A2 B2 = µ0 N1 N2 I2 g2 A2 λ2 = N2 A2 B2 = µ0 N22 I2 g2 part (c): (i) (ii) (iii) µ0 N1 I1 µ0 N2 I2 + g2 g 2 A2 A A2 1 λ1 = N1 (A1 B1 + A2 B2 ) = µ0 N12 I1 + µ0 N1 N2 I2 + g1 g2 g2 A2 A2 λ2 = N2 A2 B2 = µ0 N1 N2 I1 + µ0 N22 I2 g2 g2 B1 = µ0 N1 I1 ; g1 B2 = part (d): L11 = N12 A1 A2 + g1 g2 ; L22 = µ0 N22 A2 g2 ; L12 = µ0 N1 N2 Problem 1.23 RA = lA ; µAc R1 = l1 ; µAc R2 = l2 ; µAc Rg = g µ0 Ac part (a): L11 = N12 µAc N12 = R1 + R2 + Rg + RA /2 l1 + l2 + lA /2 + g (µ/µ0 ) A2 g2 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 10 LAA = LBB = lA + l1 + l2 + g (µ/µ0 ) N2 N 2 µAc = RA + RA ||(R1 + R2 + Rg ) lA lA + 2(l1 + l2 + g (µ/µ0 )) part (b): LAB = LBA = N 2 µAc l1 + l2 + g (µ/µ0 ) N 2 (R1 + R2 + Rg ) = RA (RA + 2(R1 + R2 + Rg )) lA lA + 2(l1 + l2 + g (µ/µ0 )) LA1 = L1A = −LB1 = −L1B = −N N1 µAc −N N1 = RA + 2(R1 + R2 + Rg ) lA + 2(l1 + l2 + g (µ/µ0 )) part (c): v1 = d d [LA1 iA + LB1 iB ] = LA1 [iA − iB ] dt dt Q.E.D. Problem 1.24 part (a): L12 = µ0 N1 N2 [D(w − x)] 2g part (b): v2 N1 N2 µ0 D dx dλ2 dL12 = I0 =− dt dt 2g dt N1 N2 µ0 D ǫ ωw = − cos ωt 2g 2 = Problem 1.25 part (a): H= N1 i1 N1 i1 = 2π(Ro + Ri )/2 π(Ro + Ri ) v2 = dB d [N2 (tn∆)B] = N2 tn∆ dt dt part (b): part (c): vo = G v2 dt = GN2 tn∆B WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 11 Problem 1.26 Rg = g = 4.42 × 105 µ0 Ag A/Wb; Rc = lc 333 A/Wb = µAg µ Want Rg ≤ 0.05Rc ⇒ µ ≥ 1.2 × 104 µ0 . By inspection of Fig. 1.10, this will be true for B ≤ 1.66 T (approximate since the curve isn’t that detailed). Problem 1.27 part (a): N1 = Vpeak = 57 turns ωt(Ro − Ri )Bpeak part (b): (i) (ii) Vo,peak = 0.833 T GN2 t(Ro − Ri ) V1 = N1 t(Ro − Ri )ωBpeak = 6.25 V, peak Bpeak = Problem 1.28 part (a): From the M-5 magnetization curve, for B = 1.2 T, Hm = 14 A/m. Similarly, Hg = B/µ0 = 9.54 × 105 A/m. Thus, with I1 = I2 = I I= Hm (lA + lC − g) + Hg g = 38.2 A N1 part (b): Wgap = gAgap B 2 = 3.21 Joules 2µ0 part (c): λ = 2N1 AA B = 0.168 Wb; Problem 1.29 part (a): L= λ = 4.39 mH I WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 12 part (b): Area = 191 Joules part (c): Core loss = 1.50 W/kg. Problem 1.30 Brms = 1.1 T and f = 60 Hz, Vrms = ωN Ac Brms = 46.7 V Core volume = Ac lc = 1.05 × 10−3 m3 . Mass density = 7.65 × 103 kg/m3 . Thus, the core mass = (1.05 × 10−3 )(7.65 × 103 ) = 8.03 kg. At B = 1.1 T rms = 1.56 T peak, core loss density = 1.3 W/kg and rms VA density is 2.0 VA/kg. Thus, the core loss = 1.3 × 8.03 = 10.4 W. The total exciting VA√for the core is 2.0 × 8.03 = 16.0 VA. Thus, its reactive component is given by 16.02 − 10.42 = 12.2 VAR. The rms energy storage in the air gap is Wgap = 2 gAc Brms = 3.61 Joules µ0 corresponding to an rms reactive power of VARgap = ωWgap = 1361 Joules Thus, the total rms exciting VA for the magnetic circuit is VArms = sqrt10.42 + (1361 + 12.2)2 = 1373 VA and the rms current is Irms = VArms /Vrms = 29.4 A. Problem 1.31 part(a): Area increases by a factor of 4. Thus the voltage increases by a factor of 4 to e = 1096cos377t. part (b): lc doubles therefore so does the current. Thus I = 0.26 A. part (c): Volume increases by a factor of 8 and voltage increases by a factor of 4. There Iφ,rms doubles to 0.20 A. part (d): Volume increases by a factor of 8 as does the core loss. Thus Pc = 128 W. Problem 1.32 From Fig. 1.19, the maximum energy product for samarium-cobalt occurs at (approximately) B = 0.47 T and H = -360 kA/m. Thus the maximum energy product is 1.69 × 105 J/m3 . Thus, 0.8 Am = 2 cm2 = 3.40 cm2 0.47 and WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 13 lm = −0.2 cm 0.8 µ0 (−3.60 × 105 ) = 0.35 cm Thus the volume is 3.40 × 0.35 = 1.20 cm3 , which is a reduction by a factor of 5.09/1.21 = 4.9. Problem 1.33 From Fig. 1.19, the maximum energy product for neodymium-iron-boron occurs at (approximately) B = 0.63 T and H = -470 kA/m. Thus the maximum energy product is 2.90 × 105 J/m3 . Thus, 0.8 Am = 2 cm2 = 2.54 cm2 0.63 and lm = −0.2 cm 0.8 µ0 (−4.70 × 105 ) = 0.27 cm Thus the volume is 2.54 × 0.25 = 0.688 cm3 , which is a reduction by a factor of 5.09/0.688 = 7.4. Problem 1.34 From Fig. 1.19, the maximum energy product for samarium-cobalt occurs at (approximately) B = 0.47 T and H = -360 kA/m. Thus the maximum energy product is 1.69 × 105 J/m3 . Thus, we want Bg = 1.2 T, Bm = 0.47 T and Hm = −360 kA/m. Hg Bg hm = −g = −g = 2.65 mm Hm µ0 Hm Am = Ag Bg Bm Rm = = 2πRh Bg Bm = 26.0 cm2 Am = 2.87 cm π Problem 1.35 From Fig. 1.19, the maximum energy product for neodymium-iron-boron occurs at (approximately) Bm = 0.63 T and Hm = -470 kA/m. The magnetization curve for neodymium-iron-boron can be represented as Bm = µR Hm + Br where Br = 1.26 T and µR = 1.067µ0. The magnetic circuit must satisfy WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 14 Hm d + Hg g = N i; Bm Am = Bg Ag part (a): For i = 0 and Bg = 0.5 T, the minimum magnet volume will occur when the magnet is operating at the maximum energy point. Bg Ag = 4.76 cm2 Am = Bm d=− Hg Hm g = 1.69 mm part (b): i= dA Bg µR Agm + N g µ0 − Br d µR For Bg = 0.75, i = 17.9 A. For Bg = 0.25, i = 6.0 A. Because the neodymium-iron-boron magnet is essentially linear over the operating range of this problem, the system is linear and hence a sinusoidal flux variation will correspond to a sinusoidal current variation. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 15 PROBLEM SOLUTIONS: Chapter 2 Problem 2.1 At 60 Hz, ω = 120π. primary: (Vrms )max = N1 ωAc (Brms )max = 2755 V, rms secondary: (Vrms )max = N2 ωAc (Brms )max = 172 V, rms At 50 Hz, ω = 100π. Primary voltage is 2295 V, rms and secondary voltage is 143 V, rms. Problem 2.2 √ 2Vrms = 167 turns N= ωAc Bpeak Problem 2.3 N= 75 =3 8 turns Problem 2.4 Resistance seen at primary is R1 = (N1 /N2 )2 R2 = 6.25Ω. Thus I1 = V1 = 1.6 A R1 and V2 = N2 N1 V1 = 40 V Problem 2.5 The maximum power will be supplied to the load resistor when its impedance, as reflected to the primary of the ideal transformer, equals that of the source (2 kΩ). Thus the transformer turns ratio N to give maximum power must be Rs N= = 6.32 Rload Under these conditions, the source voltage will see a total resistance of Rtot = 4 kΩ and the current will thus equal I = Vs /Rtot = 2 mA. Thus, the power delivered to the load will equal Pload = I 2 (N 2 Rload ) = 8 mW WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 16 Here is the desired MATLAB plot: Problem 2.6 The maximum power will be supplied to the load resistor when its impedance, as reflected to the primary of the ideal transformer, equals that of the source (2 kΩ). Thus the transformer turns ratio N to give maximum power must be Rs = 6.32 N= Rload Under these conditions, the source √ voltage will see a total impedance of Ztot = 2 kΩ. The current will thus equal I = 2 + j2 kΩ whose magnitude is 2 √ Vs /|Ztot | = 2 2 mA. Thus, the power delivered to the load will equal Pload = I 2 (N 2 Rload ) = 16 mW Here is the desired MATLAB plot: WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 17 Problem 2.7 V2 = V1 Xm Xl1 + Xm = 266 V Problem 2.8 part (a): Referred to the secondary Lm,2 = Lm,1 = 150 mH N2 part(b): Referred to the secondary, Xm = ωLm,2 = 56.7 Ω, Xl2 = 84.8 mΩ and Xl1 = 69.3 mΩ. Thus, Xm (i) V1 = N V2 = 7960 V Xm + Xl2 and (ii) Isc = V2 V2 = = 1730 A Xsc Xl2 + Xm ||Xl1 Problem 2.9 part (a): V1 = 3.47 A; I1 = Xl1 + Xm V2 = N V1 Xm Xl1 + Xm = 2398 V part (b): Let Xl′2 = Xl2 /N 2 and Xsc = Xl1 + Xm ||(Xm + Xl′2 ). For Irated = 50 kVA/120 V = 417 A V1 = Irated Xsc = 23.1 V I2 = 1 N Xm Xm + Xl2 Irated = 15.7 A Problem 2.10 IL = Pload = 55.5 A VL and thus IH = IL = 10.6 A; N VH = N VL + jXH IH = 2381 9.6◦ The power factor is cos (9.6◦ ) = 0.986 lagging. V WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 18 Problem 2.11 part (a): part (b): 30 kW jφ Iˆload = e = 93.8 ejφ 230 V A where φ is the power-factor angle. Referred to the high voltage side, IˆH = 9.38 ejφ A. V̂H = ZH IˆH Thus, (i) for a power factor of 0.85 lagging, VH = 2413 V and (ii) for a power factor of 0.85 leading, VH = 2199 V. part (c): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 19 Problem 2.12 part (a): part (b): Following methodology of Problem 2.11, (i) for a power factor of 0.85 lagging, VH = 4956 V and (ii) for a power factor of 0.85 leading, VH = 4000 V. part (c): Problem 2.13 part (a): Iload = 160 kW/2340 V = 68.4 A at = cos−1 (0.89) = 27.1◦ V̂t,H = N (V̂L + Zt IL ) which gives VH = 33.7 kV. part (b): V̂send = N (V̂L + (Zt + Zf )IL ) WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 20 which gives Vsend = 33.4 kV. part (c): ∗ Ssend = Psend + jQsend = V̂send Iˆsend = 164 kW − j64.5 kVAR Thus Psend = 164 kW and Qsend = −64.5 kVAR. Problem 2.14 Following the methodology of Example 2.6, efficiency = 98.4 percent and regulation = 1.25 percent. Problem 2.15 part (a): |Zeq,L | = Vsc,L = 107.8 mΩ Isc,L Req,L = Psc,L = 4.78 mΩ 2 Isc,L Xeq,L = 2 |Zeq,L |2 − Req,L = 107.7 mΩ and thus Zeq,L = 4.8 + j108 mΩ part (b): Req,H = N 2 Req,L = 0.455 Ω Xeq,H = N 2 Xeq,L = 10.24 Ω Zeq,H = 10.3 + j0.46 mΩ part (c): From the open-circuit test, the core-loss resistance and the magnetizing reactance as referred to the low-voltage side can be found: Rc,L = Soc,L = Voc,L Ioc,L = 497 kVA; and thus 2 Voc,L = 311 Ω Poc,L Qoc,L = 2 2 Soc,L − Poc,L = 45.2 kVAR WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 21 Xm,L = 2 Voc,L = 141 Ω Qoc,L The equivalent-T circuit for the transformer from the low-voltage side is thus: part (d): We will solve this problem with the load connected to the highvoltage side but referred to the low-voltage side. The rated low-voltage current is IL = 50 MVA/8 kV = 6.25 kA. Assume the load is at rated voltage. Thus the low-voltage terminal voltage is VL = |Vload + Zeq,L IL | = 8.058 kV and thus the regulation is given by (8.053-8)/8 = 0.0072 = 0.72 percent. The total loss is approximately equal to the sum of the open-circuit loss and the short-circuit loss (393 kW). Thus the efficiency is given by η= 50.0 Pload = = 0.992 = 99.2 percent Pin 50.39 part (e): We will again solve this problem with the load connected to the high-voltage side but referred to the low-voltage side. Now, IˆL = 6.25 25.8◦ kA. Assume the load is at rated voltage. Thus the low-voltage terminal voltage is VL = |Vload + Zeq,L IˆL | = 7.758 kV and thus the regulation is given by (7.758-8)/8 = -0.0302 = -3.02 percent. The efficiency is the same as that found in part (d), η = 99.2 percent. Problem 2.16 √ The core length of the second transformer is is 2 times that of the first, its core √ area of the second transformer is twice that of the first, and its volume is 2 2 times that of the first. Since the voltage applied to the second transformer is twice that of the first, the flux densitities will be the same. Hence, the core loss will be proportional to the volume and √ Coreloss = 2 23420 = 9.67 kW WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 22 The magnetizing inductance is proportional to the area and inversely pro√ portional to the core length√and hence is 2 times larger. Thus the no-load magnetizing current will be 2 times larger in the second transformer or √ Ino−load = 2 4.93 = 6.97 A Problem 2.17 part (a): Rated current at the high-voltage side is 20 kVA/2.4 kV = 8.33 A. Thus the total loss will be Ploss = 122 + 257 = 379 W. The load power is equal to 0.8 × 20 = 16 kW. Thus the efficiency is η= 16 = 0.977 = 97.7 percent 16.379 part (b): First calculate the series impedance (Zeq,H = Req,H + jXeq,H ) of the transformer from the short-circuit test data. Req,H = Psc,H = 3.69 Ω 2 Isc,H Ssc,H = Vsc,H Isc,H = 61.3 × 8.33 = 511 kV A Thus Qsc,H = 2 2 Ssc,H − Psc,H = 442 VAR and hence Xeq,H = Qsc,H = 6.35 Ω 2 Isc,H The regulation will be greatest when the primary and secondary voltages of the transformer are in phase as shown in the following phasor diagram Thus the voltage drop across the transformer will be equal to ∆V = |Iload ||Zeq,H | = 61.2 V and the regulation will equal 61.2 V/2.4 kV = 0.026 = 2.6 percent. Problem 2.18 For a power factor of 0.87 leading, the efficiency is 98.4 percent and the regulation will equal -3.48 percent. Problem 2.19 part (a): The voltage rating is 2400 V:2640 V. part (b): The rated current of the high voltage terminal is equal to that of the 240-V winding, Irated = 30 × 103/240 = 125 A. Hence the kVA rating of the transformer is 2640 × 125 = 330 kVA. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 23 Problem 2.20 part (a): part (b): The rated current of the high voltage terminal is equal to that of the 120-V winding, Irated = 104 /120 = 83.3 A. Hence the kVA rating of the transformer is 600 × 83.3 = 50 kVA. part (c): The full load loss is equal to that of the transformer in the conventional connection, Ploss = (1 − 0.979) 10 kW = 210 W. Hence as an autotransformer operating with a load at 0.85 power factor (Pload = 0.85 × 50 kW = 42.5 kW), the efficiency will be η= 42.5 kW = 0.995 = 99.5 percent 42.71 kW Problem 2.21 part (a): The voltage rating is 78 kV:86 kV. The rated current of the high voltage terminal is equal to that of the 8-kV winding, Irated = 50 × 106 /8000 = 6.25 kA. Hence the kVA rating of the transformer is 86 kV × 6.25 kA = 537.5 MVA. part (b): The loss at rated voltage and current is equal to 393 kW and hence the efficiency will be η= 537.5 MW = 0.9993 = 99.93 percent 538.1 MW Problem 2.22 No numerical result required for this problem. Problem 2.23 part (a): 7.97 kV:2.3 kV; 191 A:651 A; 1500 kVA part (b): 13.8 kV:1.33 kV; 109 A:1130 A; 1500 kVA part (c): 7.97 kV:1.33 kV; 191 A:1130 A; 1500 kVA part (d): 13.8 kV:2.3 kV; 109 A:651 A; 1500 kVA Problem 2.24 part (a): (i) 23.9 kV:115 kV, 300 MVA (ii) Zeq = 0.0045 + j0.19 Ω (iii) Zeq = 0.104 + j4.30 Ω WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 24 part (b): (i) 23.9 kV:66.4 kV, 300 MVA (ii) Zeq = 0.0045 + j0.19 Ω (iii) Zeq = 0.0347 + j1.47 Ω Problem 2.25 Following the methodology of Example 2.8, Vload = 236 V, line-to-line. Problem 2.26 The total series impedance is Ztot = Zf + Zt = j11.7 + 0.11 + j2.2 Ω = 0.11 + j13.9 Ω. The transformer turns ratio is N = 9.375. The load current, as referred to the transformer high-voltage side will be 325 MVA Iload = N 2 √ ejφ = 7.81ejφ kA 3 24 kV −1 ◦ where √ φ = − cos 0.93 = −21.6 . The line-to-neutral load voltage is Vload = 24 3 kV. part (a): At the transformer high-voltage terminal V = √ 3 |N Vload + Iload Zt | = 231.7 kV, line-to-line part (b): At the sending end V = √ 3 |N Vload + Iload Ztot | = 233.3 kV, line-to-line Problem 2.27 Problem 2.28 First calculate the series impedance (Zeq,H = Req,H + jXeq,H ) of the transformer from the short-circuit test data. Zeq,H = 0.48 = j1.18 Ω WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 25 The total imedance between the load and the sending end of the feeder is Ztot√= Zf + Zeq,H = 0.544 + j2.058 Ω. The transformer turns ration is N = 2400:120 3 = 11.6. part (a): The referred load voltage Vload and current Iload will be in phase and can be assumed to be the phase reference. Thus we can write the phasor equation for the sending-end voltage as: V̂s = Vload + Iload Ztot √ We know that Vs = 2400/sqrt3 = 1386 V and that Iload = 100 kVA/( 32.4 kV). Taking the magnitude of both sides of the above equation gives a quadradic equation in Vload 2 2 Vload + 2Rtot Iload Vload + |Ztot |2 Iload − Vs2 which can be solved for Vload Vload = −Rtot Iload + Vs2 − (Xtot Iload )2 = 1.338 kV Referred to the low-voltage side, this corresponds to a load voltage of 1.338 kV/N = 116 V, line-to-neutral or 201 V, line-to-line. part (b): 2400 = 651 A Feeder current = √ 3Ztot 651 HV winding current = √ = 376 A 3 LV winding current = 651N = 7.52 kA Problem 2.29 part (a): The transformer turns ratio is N = 7970/120 = 66.4. The secondary voltage will thus be V1 jXm V̂2 = = 119.74 0.101◦ N R1 + jX1 + jXm part (b): Defining RL′ = N 2 RL = N 2 1 kΩ = 4.41 MΩ and Zeq = jXm ||(R2′ + RL′ + jX2′ ) = 134.3 + j758.1 kΩ the primary current will equal Iˆ1 = 7970 = 10.3 − 79.87◦ mA R1 + jX1 + Zeq WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 26 The secondary current will be equal to jXm ˆ ˆ I2 = N I1 = 119.7 0.054◦ R2′ + RL′ + j(Xm + X2 ) mA and thus V̂2 = RL Iˆ2 = 119.7 0.054◦ V part (c): Following the methodology of part (b) V̂2 = 119.6 0.139◦ V Problem 2.30 This problem can be solved iteratively using MATLAB. The minimum reactance is 291 Ω. Problem 2.31 part (a): part (b): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 27 Problem 2.32 part (a): The transformer turns ratio N = 200/5 = 40. For I1 = 200 A I1 jXm I2 = = 4.987 0.024◦ N R2′ + j(Xm + X2′ ) part (b): Defining RL′ = N 2 250µΩ = 0.4 Ω I1 jXm I2 = = 4.987 0.210◦ N R2′ + RL′ + j(Xm + X2′ ) Problem 2.33 part (a): part (b): Problem 2.34 Zbase,L = Zbase,H = 2 Vbase,L Pbase 2 Vbase,H Pbase = 1.80 Ω = 245 Ω WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 28 Thus R1 = 0.0095Zbase,L = 17.1 mΩ; X1 = 0.063Zbase,L = 113 mΩ Xm = 148Zbase,L = 266 Ω R2 = 0.0095Zbase,H = 2.33 Ω; X2 = 0.063Zbase,H = 15.4 Ω Problem 2.35 part (a): (i) Zbase,L = (7.97 × 103 )2 = 0.940 Ω; 75 × 103 (ii) Zbase,H = (7970)2 = 847 Ω; 75 × 103 XL = 0.12Zbase,L = 0.113 Ω XH = 0.12Zbase,H = 102 Ω part (b): (i) 797 V:13.8 kV, 225 kVA (ii) Xpu = 0.12 (iii) XH = 102 Ω (iv) XL = 0.339 Ω part (c): (i) 460 V:13.8 kV, 225 kVA (ii) Xpu = 0.12 (iii) XH = 102 Ω (iv) XL = 0.113 Ω Problem 2.36 part (a): In each case, Ipu = 1/0.12 = 8.33 pu. √ √ (i) Ibase,L = Pbase /( 3 Vbase,L ) = 225 kVA/( 3 797 V) = 163 A IL = Ipu Ibase,L √ = 1359 A √ (ii) Ibase,H = Pbase /( 3 Vbase,H ) = 225 kVA/( 3 13.8 kV) = 9.4 A IH = Ipu Ibase,H = 78.4 A part (b): In each case, Ipu = 1/0.12 = 8.33 pu. √ √ (i) Ibase,L = Pbase /( 3 Vbase,L ) = 225 kVA/( 3 460 V) = 282 A IL = Ipu Ibase,L √ = 2353 A √ (ii) Ibase,H = Pbase /( 3 Vbase,H ) = 225 kVA/( 3 13.8 kV) = 9.4 A IH = Ipu Ibase,H = 78.4 A 29 Problem 2.37 part (a): On the transformer base 800 MVA Pbase,t Xgen = 1.57 = 1.57 = 1.27 pu Pbase,g 850 MVA part (b): On the transformer base, the power supplied to the system is Pout = 700/850 = 0.824 pu and the total power is Sout = Pout /pf = 0.825/0.95 = 0.868 pu. Thus, the per unit current is Iˆ = 0.868 φ, where φ = − cos−1 0.95 = −18.2◦. (i) The generator terminal voltage is thus ˆ t = 1.03 3.94◦ pu = 26.8 3.94◦ kV V̂t = 1.0 + IZ and the generator internal voltage is ˆ t + Zgen ) = 2.07 44.3◦ pu = 53.7 44.3◦ kV V̂gen = 1.0 + I(Z (ii) The total output of the generator is given by Sgen = V̂t Iˆ∗ = 0.8262 + 0.3361. Thus, the generator output power is Pgen = 0.8262 × 850 = 702.2 MW. The correspoinding power factor is Pgen /|Sgen | = 0.926 lagging. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 30 PROBLEM SOLUTIONS: Chapter 3 Problem 3.1 By analogy to Example 3.1, T = 2B0 Rl [I1 sin α + I2 cos α] = 6.63 × 10−2 [I1 sin α + I2 cos α] N·m Thus part (a): T = 0.530 cos α N·m part (b): T = 0.530 sin α N·m part (c): T = 0.530 [I1 sin α + I2 cos α] N·m Problem 3.2 T = 0.5304 N·m Problem 3.3 Can calculate the inductance as L= 1000 × 0.13 Nφ = = 13 H I 10 Thus Wfld = 1 LI 2 = 650 Joules 2 Problem 3.4 part (a): For x = 0.9 mm, L = 29.5 mH and thus, for I = 6 A, Wfld = 0.531 Joules. part (b):For x = 0.9 mm, L = 19.6 mH and thus, for I = 6 A, Wfld = 0.352 Joules. Hence, ∆Wfld = −0.179 Joules. Problem 3.5 For a coil voltage of 0.4 V, the coil current will equal I = 0.4/0.11 = 3.7 A. Under the assumption that all electrical transients have died out, the solution will be the same as that for Problem 3.4, with a current of 3.7 A instead of 6.0 A. part (a): Wfld = 0.202 Joules part (b): ∆Wfld = −0.068 Joules. Problem 3.6 √ For x = x0 , L = L0 = 30 mH. The rms current is equal to Irms = I0 / 2 and thus part (a): < Wfld >= 1 2 LI = 0.227 Joules 2 rms WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 31 part (b): 2 R = 1.63 W < Pdiss >= Irms Problem 3.7 part (a): Bg = Wfld ! = Bg2 2µ0 = µ0 N 2 A0 4g µ0 N i 2g Bg2 2µ0 × Air-gap volume = 1− 4θ π 2 ! ! i2 part (b): 2Wfld µ0 N 2 A0 L= = i2 2g 1− 4θ π 2 ! Here is the MATLAB plot: Problem 3.8 part (a): vC (t) = V0 e−t/τ ; τ = RC 2 part (b): Wfld = q 2 /(2C) = CvC /2. Thus Wfld (0) = CV02 ; 2 Wfld (∞) = 0 × 2gAg WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 32 part (c) iR (t) = vC (t) ; R Wdiss = Pdiss (t) = i2R (t)R = Z ∞ Pdiss (t) dt = 0 V02 e−2t/τ R CV02 2 Problem 3.9 part (a): iL (t) = V0 −t/τ e ; R τ= L R part (b): Wfld (0) = V02 L ; 2R2 Wfld (∞) = 0 part (c) Pdiss (t) = i2L (t)R = Wdiss = Z V02 e−2t/τ R ∞ Pdiss (t) dt = 0 V02 L 2R2 Problem 3.10 Given: τ= L = 4.8 sec; R I 2 R = 1.3 MW Thus 1 2 1 Li = L 2 2 i2 R R = τ 2 i2 R = 6.24 MJoules Problem 3.11 part (a): Four poles part (b): Tfld = 2 ′ d ∂Wfld I0 = (L0 + L2 cos 2θm ) = −I02 L2 sin 2θm ∂θm dθm 2 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 33 Problem 3.12 part (a): Bg = µ0 N i g + g1 R/(2h) where g1 is the length of the fixed gap, l is its length and R is the radius of the solenoid. Here is the MATLAB plot: part (b): 2 Wfld = πR g Here is the MATLAB plot: Bg2 2µ0 ! WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 34 part (c): L = 2Wfld /i2 . Here is the MATLAB plot: Problem 3.13 If the plunger is moved very slowly (i.e. idL/dt << Ldi/dt, the current will be essentially constant and all of the change in stored energy will come from the mechanical work applied to the plunger. Thus, part (a): Work = Wfld (g = 0.2 cm) − Wfld (g = 2.25 cm) = 46.7 µJoules part (b): The battery will supply only the energy dissipated in the coil. Problem 3.14 The coil inductance is equal to L = µ0 N 2 Ac /(2g) and hence the lifting force is equal to i2 dL µ0 N 2 Ac 2 ffld = i =− 2 dg 4g 2 where the minus sign simply indicates that the force acts in the direction to reduce the gap (and hence lift the mass). The required force is equal to 931 N (the mass of the slab times the acceleration due to gravity, 9.8 m/sec2 ). Hence, setting g = gmim and solving for i gives s ffld 2gmin = 385 mA imin = N µ0 Ac and vmin = imin R = 1.08 V. Problem 3.15 part (a): a1 = −9.13071 × 10−5 a2 = 0.124209 a3 = 28.1089 a4 = 10558.2 b1 = 9.68319 × 10−11 b2 = −1.37037 × 10−7 b3 = 6.32831 × 10−5 b4 = 1.71793 × 10−3 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 35 part (b): (i) Here is the MATLAB plot: (ii) ′ Wfld = 13.0 Joules and Wfld = 13.7 Joules ′ Assuming no core relctance, Wfld = 11.8 Joules and Wfld = 13.0 Joules part (c): (i) Here is the MATLAB plot: (ii) ′ Wfld = 142 Joules and Wfld = 148 Joules ′ Assuming no core relctance, Wfld = 139 Joules and Wfld = 147 Joules Problem 3.16 µ0 N 2 Ac ; L= g ffld = i2 2 dL i2 L =− dg 2g The time-averaged force can be found by setting i = Irms where Irms = Vrms /(ωL). Thus < ffld >= − V2 Irms = −115 N = − 2 rms 2 2 2gω L 2ω µ0 N Ac WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 36 Because the inductor is being driven by a voltage source, the gap flux density remains constant independent of the air-gap length and hence the force also remains constant. Problem 3.17 part (a): Bs = µ0 i s part (b): φs = Bs xl = µ0 xl s part (c): Note that as the coil moves upward in the slot, the energy associated with the leakage flux associated withing the coil itself remains constant while the energy in the leakage flux above the coil changes. Hence to use the energy method to calculate the force on the coil it is necessary only to consider the energy in the leakage flux above the slot. Wfld = Z Bs2 µ0 xli2 dV = 2µ0 2s Because this expression is explicity in terms of the coil current i and becasue the magnetic energy is stored in air which is magnetically linear, we know that ′ = Wfld . We can therefore find the force from Wfld ffld = ′ µ0 li2 dWfld = dx 2s This force is positive, acting to increase x and hence force the coil further into the slot. part (d): ffld = 18.1 N/m. Problem 3.18 ′ Wfld = µ0 H 2 2 × coil volume = µ0 πr02 N 2 2h Thus ′ dWrmf ld f= = dr0 µ0 πr0 N 2 h and hence the pressure is P = f = 2πr0 h µ0 N 2 2h2 I02 I02 i2 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 37 The pressure is positive and hence acts in such a direction as to increase the coil radius r0 . Problem 3.19 part (a): Wfld (q, x) = Z q v(q ′ , x)dq ′ 0 part (b): ffld = − ∂Wfld ∂x q part (c): ′ ′ Wfld = vq − dWfld ⇒ dWfld = qdv + ffld dx Thus ′ Wfld = Z v q(v ′ , x)dv ′ ; ffld = 0 ′ ∂Wfld ∂x v Problem 3.20 part (a): Wfld = ′ Wfld = Z Z q v(q ′ , x)dq ′ = 0 v q(v ′ , x)dv ′ = 0 xq 2 q2 = 2C 2ǫ0 A ǫ0 Av 2 Cv 2 = 2 2x part (b): ′ ∂Wfld ∂x ffld = = v Cv 2 ǫ0 Av 2 = 2 2x2 and thus ffld (V0 , δ) = ǫ0 AV02 2δ 2 Problem 3.21 part (a): Tfld = 2 Vdc 2 dC = dθ Rd 2g 2 Vdc part (b): In equilibrium, Tfld + Tspring = 0 and thus WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 38 θ = θ0 + Rd 2gK 2 Vdc Here is the plot: Problem 3.22 part (a): µ0 N12 A ; 2g0 L11 = L22 = µ0 N22 A 2g0 part (b): L12 = µ0 N1 N2 A ; 2g0 part (c): ′ Wfld = 1 1 µ0 A 2 L11 i21 + L22 i22 + L12 i1 i2 = (N1 i1 + N2 i2 ) 2 2 4g0 part (d): ffld = ′ ∂Wfld ∂g0 i1 ,i2 =− µ0 A (N1 i1 + N2 i2 )2 4g02 Problem 3.23 part (a): ′ Wfld = 1 1 L11 i21 + L22 i22 + L12 i1 i2 = I 2 (L11 + L22 + 2L12 ) sin2 ωt 2 2 Tfld = ′ ∂Wfld ∂θ i1 ,i2 = −4.2 × 10−3 I 2 sin θ sin2 ωt N·m WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 39 part (b): Tfld = −2.1 × 10−3 I 2 sin θ N·m part (c): Tfld = −0.21 N·m. part (d): part (e): The curve of spring force versus angle is plotted as a straight line on the plot of part (d). The intersection with each curve of magnetic force versus angle gives the equilibrium angle for that value of current. For greater accuracy, MATLAB can be used to search for the equilibrium points. The results of a MATLAB analysis give: I 5 7.07 10 part (f): θ 52.5◦ 35.3◦ 21.3◦ WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 40 Problem 3.24 part (a): Tfld = i1 i2 dL12 = −2.8i1i2 sin θ dθ λ2 = 0 ⇒ i 2 = − L12 L22 N·m i1 = −1.12i1 cos θ Therefore, for i1 = 10 sin ωt, Tfld = −3.14i21 sin θ cos θ = −314 sin2 (ωt) sin θ cos θ = −78.5 (1 − cos (2ωt)) sin (2θ) N·m part (b): < Tfld >= −78.5 N·m part (c): It will not rotate. It will come to rest at angular positions where < Tfld >= 0 and d < Tfld > =0 dθ i.e. at θ = 90◦ or θ = 270◦. Problem 3.25 part (a): Winding 1 produces a radial magnetic which, under the assumption that g << r0 , Br,1 = µ0 N1 i1 g The z-directed Lorentz force acting on coil 2 will be equal to the current in coil 2 multiplied by the radial field Br,1 and the length of coil 2. fz = 2πr0 N2 Br,1 i2 = 2πr0 µ0 N1 N2 i1 i2 g part (b): The self inductance of winding 1 can be easily written based upon the winding-1 flux density found in part (a) L11 = 2πr0 lµ0 N12 g The radial magnetic flux produced by winding 2 can be found using Ampere’s law and is a function of z.  0≤z≤x   0 µ0 N2 i2 (z−x) − x ≤z ≤x+h Bz = gh   − µ0 N2 i2 x+h≤z ≤l g WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 41 Based upon this flux distribution, one can show that the self inductance of coil 2 is 2h 2πr0 µ0 N22 l−x− L22 = g 3 part (c): Based upon the flux distribution found in part (b), the mutual inductance can be shown to be 2πr0 µ0 N1 N2 h L12 = x+ −l g 2 part (d): ffld d = dx πr0 µ0 N22 2 2πr0 µ0 N1 N2 1 1 2 2 i1 i2 L11 i1 + L22 i2 + L12 i1 i2 = − i2 + 2 2 g g Note that this force expression includes the Lorentz force of part (a) as well as a reluctance force due to the fact that the self inductance of coil 2 varies with position x. Substituting the given expressions for the coil currents gives: ffld = − πr0 µ0 N22 2 2πr0 µ0 N1 N2 I2 cos2 ωt + I1 I2 cos ωt g g Problem 3.26 The solution follows that of Example 3.8 with the exception of the magnet properties of samarium-cobalt replaced by those of neodymium-boron-iron for which µR = 1.06µ0 , Hc′ = −940 kA/m and Br = 1.25 T. The result is -203 N at x = 0 cm ffld = -151 N at x = 0.5 cm Problem 3.27 part (a): Because there is a winding, we don’t need to employ a “fictitious” winding. Solving Hm d + Hg g0 = N i; Bm wD = Bg (h − x)D in combination with the constitutive laws Bm = µR (Hm − Hc ); Bg = µ0 Hg gives Bm = µ0 (N i + Hc d) dµ0 µR + wg0 (h−x) Note that the flux in the magnetic circuit will be zero when the winding current is equal to I0 = −Hc d/N . Hence the coenergy can be found from WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 42 integrating the flux linkage of the winding from an initial state where it is zero (i.e. with i = I0 ) to a final state where the current is equal to i. The flux linkages are given by λ = N wDBm and hence ′ (i, x) = Wfld Z i λ(i′ , x)di′ = I0 µ0 wDN dµ0 wg0 µR + (h−x) Hc d N i2 + Hc i + 2 2N The force is then ffld 2 ′ Ni dWfld Hc d −µ0 w2 DN g0 = = µ d(h−x) + Hc i + dx 2 2N + wg0 )2 ( 0 µR (i) for i = 0, ffld = ′ dWfld −µ0 w2 Dg0 (Hc d)2 = µ d(h−x) dx + wg0 )2 2( 0 µR where the minus sign indicates that the force is acting upwards to support the mass against gravity. (ii) The maximum force occurs when x = h fmax = − µ0 wD(Hc d)2 = −Mmaxa 2 where a is the acceleration due to gravity. Thus Mmax = µ0 wD(Hc d)2 2a part (b): Want f (Imin,x=h = −a µ0 wD(Hc d)2 Mmax =− 2 4 Substitution into the force expression of part (a) gives Imin = (2 − √ 2)(−Hc d) = −0.59Hcd Problem 3.28 part (a): Combining Hm d + Hg g = 0; Bg = µ0 Hg ; gives πr02 Bm = 2πr0 lBg Bm = µR (Hm − Hrmc ) WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 43 Bg = g+ −Hc dµ0 µ0 µR 2ld r0 part (b): The flux linkages of the voice coil can be calculate in two steps. First calculate the differential flux linkages of a differential section of the voice coil of dN2 turns at height z ′ above the bottom of the voice coil (which is at z = x).   Z l ′ (−H dµ )(2πr )(l − z ) c 0 0  dN2 dλ2 = dN2 Bg (2πr0 )dz =  2ld z′ g + µµR0 r0 Recognizing that dN2 = (N2 /h)dz ′ we can now integrate over the coil to find the total flux linkages Z x+h N2 (−Hc dµ0 )(2πr0 )(l − x − h/2) λ2 = dλ2 = 2ld x g + µµR0 r0 part (c): Note from part (a) that the magnet in this case can be replaced by a winding of N1 i1 = −Hc d ampere-turns along with a region of length d and permeability µR . Making this replacement from part (a), the self inductance of the winding can be found λ11 = N1 Φ11 = 2πr0 hN1 Bg = and thus L11 = 2πr0 hN12 dµ0 i1 2ld g + µµR0 r0 2πr0 hN12 dµ0 2ld g + µµR0 r0 Similar, the mutual inductance with the voice coil can be found from part (b) as L12 = N1 λ 2 N2 N2 µ0 (2πr0 )(l − x − h/2) λ2 = = 2ld i1 −Hc d g + µ0 µR r0 We can now find the coenergy (ignoring the term L22 i22 /2) ′ Wfld = = 1 L11 i21 + L12 i1 i2 2 µ0 N2 (−Hc d)(2πr0 d)(l − x − h2 ) µ0 (Hc d)2 πr0 h + i2 µ0 2ld 2ld g + µµR0 g + r0 µR r0 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 44 part (d): ′ dWfld µ0 N2 (−Hc d)(2πr0 d) =− 2ld dx g + µ0 ffld = µR Problem 3.29 part (a): π(R32 − R22 )Bm = πR12 Bx = 2πR1 hBg Hm tm + Hx x + Hg g = 0; Bg = µ0 Hg ; r0 Bx = µ0 Hx ; Bm = µR (Hm − Hc ) where µR = 1.05µ0 and Hc′ = −712 kA/m. Solving gives   µ R (−H t ) 0 1 c m  = 0.562 T Bg =  2µ0 R21 htm 2hx + gR1 + µR (R2 −R2 ) 3 2 and Bx = 2h R1 Bg = 0.535 T part (b): We can replace the magnet by an equivalent winding of N i = −Hc tm . The flux linkages of this equivalent winding can then be found to be   2 2 2πµ0 hR1 N  i = Li λ = N (2πR1 h)Bg =  2µ0 R21 htm 2hx + gR1 + µR (R 2 −R2 ) 3 2 The force can then be found as ffld = = i2 dL = 2 dx −2πµ0 (hR1 )2 (N i)2 2hx + gR1 + 2 −2πµ0 (hR1 )2 (−Hc tm )2 2 = −0.0158 N 2µ0 R21 htm 2hx + gR1 + µR (R 2 −R2 ) 3 part (c): 2µ0 R21 htm µR (R23 −R22 ) X0 = x − 2 f = 4.0 mm K WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 45 Problem 3.30 part (a): If the plunger is stationary at x = 0.9a, the inductance will be constant at L = 0.1L0 . Thus i(t) = V0 −t/τ e R where τ = L/R. The force will thus be ffld L0 i2 dL =− = 2 dx 2a V0 R 2 e−2t/τ part (b): X0 = 0.9a + L0 f = 0.9a − K0 2aK0 V0 R 2 Problem 3.31 part (a): Since the current is fixed at i = I0 = 4 A, the force will be constant at f = −I02 L0 /()2a = −1.45 N. Thus X0 = 0.9 ∗ a + f = 1.56 cm K0 part (b): M d2 x d2 x = f + K (0.9a − x) ⇒ 0.2 = 5.48 − 350x N 0 dt2 dt2 v = I0 R + I0 L0 dx dx dL = I0 R − ⇒ v = 6 − 0.182 dt a dt dt part (c): The equations can be linearized by letting x = X0 + x′ (t) and v = V0 + v ′ (t). The result is d2 x′ = −1750x′ dt2 and v ′ = −0.182 dx′ dt part (d) For ǫ in meters, x′ (t) = ǫ cos ωt m where ǫ = √ 1750 = 41.8 rad/sec and WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 46 v ′ (t) = 7.61ǫ sin ωt V Problem 3.32 part (a): For a dc voltage of V0 = 6 V, the corresponding dc current will be I0 = V0 /R = 4 A, the same as Problem 3.31. Hence the equilibrium position will be the same; X0 = 1.56 cm. part (b): For a fixed voltage, the dynamic equations become: dx L0 d x di i − V0 = iR + (Li) = iR + L0 1 − dt a dt a dt or 6 = 1.5i + 4 × 10−3 (1 − 40x) dx di − (0.182) i dt dt and d2 x M 2 = f − K0 (0.9a − x) = − dt i2 2 L0 a + K0 (0.9a − x) or 0.2 d2 x = −0.0909i2 + 6.93 − 350x dt2 part (c): The equations can be linearized by letting x = X0 + x′ (t) and i = I0 + i′ (t). The result is dx X0 di′ L0 I0 0 = i′ R + L0 1 − − a dt a dt or 0 = 1.5i′ + 1.5 × 10−3 dx di′ − 0.728 dt dt and M d2 x′ =− dt2 I0 L0 a i ′ − K 0 x′ or 0.2 d2 x = −0.727i2 − 350x′ dt2 Problem 3.33 part (a): Following the derivation of Example 3.1, for a rotor current of 8 A, the torque will be give by T = T0 sin α where T0 = −0.0048 N·m. The stable equilibrium position will be at α = 0. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 47 part (b): J d2 α = T0 sin α dt2 part (c): The incremental equation of motion is J d2 α = T0 α dt2 and the natural frequency is ω= r T0 = 0.62 rad/sec J corresponding to a frequency of 0.099 Hz. Problem 3.34 As long as the plunger remains within the core, the inductance is equal to µ0 dπN 2 a 2 − x2 L= ag 2 where x is the distance from the center of the solenoid to the center of the core. Hence the force is equal to ffld = µ0 dπN 2 i2 x i2 dL =− 2 dx ag Analogous to Example 3.10, the equations of motor are ft = −M d2 x dx µ0 dπN 2 i2 x − B − K(x − l ) − 0 dt2 dt ag The voltage equation for the electric system is di 2µ0 dπN 2 x dx µ0 dπN 2 a 2 − x2 − vt = iR + ag 2 dt ag dt These equations are valid only as long as the motion of the plunger is limited so that the plunger does not extend out of the core, i.e. ring, say, between the limits −a/2 < x < a/2. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 48 PROBLEM SOLUTIONS: Chapter 4 Problem 4.1 part (a): ωm = 1200 × π/30 = 40π rad/sec part (b): 60 Hz; 120π rad/sec part (c): 1200 × 5/6 = 1000 r/min Problem 4.2 The voltages in the remaining two phases can be expressed as V0 cos (ωt − 2π/3) and V0 cos (ωt + 2π/3). Problem 4.3 part (a): It is an induction motor. parts (b) and (c): It sounds like an 8-pole motor supplied by 60 Hz. Problem 4.4 part (a): part (b): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 49 part (c): part (d): Problem 4.5 Under this condition, the mmf wave is equivalent to that of a single-phase motor and hence the positive- and negative-traveling mmf waves will be of equal magnitude. Problem 4.6 The mmf and flux waves will reverse direction. Reversing two phases is the procedure for reversing the direction of a three-phase induction motor. Problem 4.7 F1 = Fmax cos θae cos ωe t = Fmax (cos (θae − ωt ) + cos (θae + ωt )) 2 F2 = Fmax sin θae sin ωe t = Fmax (cos (θae − ωt ) − cos (θae + ωt )) 2 and thus Ftotal = F1 + F2 = Fmax cos (θae − ωt ) WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 50 Problem 4.8 For n odd R β/2 −β/2 R π/2 −π/2 For β = 5π/6, cos (nθ)dθ cos (nθ)dθ = sin (   0.97 nθ 0 sin ( ) =  2 0.26 nθ ) 2 n=1 n=3 n=5 Problem 4.9 part (a): Rated speed = 1200 r/min part (b): Ir = πgBag1,peak (poles) = 113 A 4µ0 kr Nr part (c): 2 lRBag1,peak = 0.937 Wb ΦP = 3 Problem 4.10 From the solution to Problem 4.9, ΦP = 0.937 Wb. ωN Φ Vrms = √ = 8.24 kV 2 Problem 4.11 From the solution to Problem 4.9, ΦP = 0.937 Wb. Vrms = ωkw Na Φ √ = 10.4 kV 2 Problem 4.12 √ The required rms line-to-line voltage is Vrms = 13.0/ 3 = 7.51 kV. Thus √ 2 Vrms = 39 turns Na = ωkw Φ Problem 4.13 part (a): The flux per pole is Φ = 2lRBag1,peak = 0.0159 Wb The electrical frequency of the generated voltage will be 50 Hz. The peak voltage will be WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 51 Vpeak = ωN Φ = 388 V Because the space-fundamental winding flux linkage is at is peak at time t = 0 and because the voltage is equal to the time derivative of the flux linkage, we can write v(t) = ±Vpeak sin ωt where the sign of the voltage depends upon the polarities defined for the flux and the stator coil and ω = 120π rad/sec. part (b): In this case, Φ will be of the form Φ(t) = Φ0 cos2 ωt where Φ0 = 0.0159 Wb as found in part (a). The stator coil flux linkages will thus be 1 λ(t) = ±N Φ(t) = N Φ0 cos2 ωt = ± N Φ0 (1 + cos 2ωt) 2 and the generated voltage will be v(t) = ∓ωΦ0 sin 2ωt This scheme will not work since the dc-component of the coil flux will produce no voltage. Problem 4.14 Fa = ia [A1 cos θa + A3 cos 3θa + A5 cos 5θa ] = Ia cos ωt[A1 cos θa + A3 cos 3θa + A5 cos 5θa ] Similarly, we can write = ib [A1 cos (θa − 120◦ ) + A3 cos 3(θa − 120◦) + A5 cos 5(θa − 120◦ )] Fb = Ia cos (ωt − 120◦)[A1 cos (θa − 120◦ ) + A3 cos 3θa + A5 cos (5θa + 120◦ )] and Fc = ic [A1 cos (θa + 120◦ ) + A3 cos 3(θa + 120◦ ) + A5 cos 5(θa + 120◦)] = Ia cos (ωt + 120◦ )[A1 cos (θa + 120◦ ) + A3 cos 3θa + A5 cos (5θa − 120◦)] The total mmf will be WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 52 Ftot = Fa + Fb + Fc 3 Ia [A1 cos (θa − ωt)A5 cos (5θa + ωt)] = 2 3 ωt = Ia [A1 cos (θa − ωt)A5 cos 5 θa + ( ) ] 2 5 We see that the combined mmf contains only a fundamental space-harmonic component that rotates in the forward direction at angular velocity ω and a 5’th space-harmonic that rotates in the negative direction at angular velocity ω/5. Problem 4.15 The turns must be modified by a factor of 9 1200 18 = = 0.64 24 1400 14 Problem 4.16 Φp = 30Ea = 6.25 mWb N (poles)n Problem 4.17 part (a): 2 2 2Bpeaklr = × 2 × 1.25 × 0.21 × (.0952/2) = 12.5 mWb Φp = poles 4 Nph √ (230/ 3) × 4 Vrms × poles = 43 turns =√ =√ 2 πfme kw Φp 2 π × 60 × 0.925 × 0.0125 part (b): From Eq. B.27 16µ0 lr L= πg kw Nph poles 2 = 21.2 mH Problem 4.18 part (a): Φp = √ Vrms = 10.8 mWb 2 πNph Bpeak = Φp = 0.523 T 2lr WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 53 part (b): If = πBpeak g = 0.65 A 2µ0 kr Nr part (c): λa,peak = = If Laf √ 2 Vrms /ω = 0.69 H If Problem 4.19 No numerical solution required. Problem 4.20 Φpeak = Tpeak poles 2 2 Bpeak 4kr Nr Ir,max π × poles Fr,peak = π = 2 2Dl poles Φpeak Fr,peak = 4.39 × 106 N·m Ppeak = Tpeakωm = 828 MW Problem 4.21 Φpeak = Fr,peak = Tpeak π = 2 poles 2 2 2Dl poles Bpeak 4kr Nr Ir,max π × poles Φpeak Fr,peak = 16.1 N·m Ppeak = Tpeak ωm = 6.06 kW Problem 4.22 part (a): T dMaf dMbf + ib if dθ0 dθ0 = M if (ib cos θ0 − ia sin θ0 ) = ia if WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 54 This expression applies under all operating conditions. part (b): √ T = 2M I02 (cos θ0 − sin θ0 ) = 2 2 M I02 sin (θ0 − π/4) Provided there are any losses at all, the rotor will come to rest at θ0 = π/4 for which T = 0 and dt/dθ0 < 0. part (c): T = = √ √ 2 M Ia If (sin ωt cos θ0 − cos ωt sin θ0 ) √ 2 M Ia If sin (ωt − θ0 ) = 2 M Ia If sin δ part (d): d (Laa ia + Maf if ) = Ra ia + dt √ 2 Ia (Ra cos ωt − ωLaa sin ωt) − ωM If sin (ωt − δ) = va d (Laa ib + Mbf if ) = Ra ib + dt √ = 2 Ia (Ra sin ωt + ωLaa cos ωt) + ωM If cos (ωt − δ) vb Problem 4.23 T = M If (ib cos θ0 − ia sin θ0 ) √ = 2 M If [(Ia + I ′ /2) sin δ + (I ′ /2) sin (2ωt + δ)] The time-averaged torque is thus < T >= √ 2 M If (Ia + I ′ /2) sin δ Problem 4.24 part (a): T dLab dMaf dMbf i2 dLbb i2a dLaa + b + ia ib + ia if + ib if 2 dθ0 2 dθ0 dθ0 dθ0 dθ0 √ 2 2 Ia If M sin δ + 2Ia L2 sin 2δ = = part (b): Motor if T > 0, δ > 0. Generator if T < 0, δ < 0. part (c): For If = 0, there will still be a reluctance torque T = 2Ia2 L2 sin 2δ and the machine can still operate. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 55 Problem 4.25 part (a): v= f = 25 m/sec λ part (b): The synchronous rotor velocity is 25 m/sec. part (c): For a slip of 0.045, the rotor velocity will be (1 − 0.045) × 25 = 23.9 m/sec. Problem 4.26 Irms = = π 2p 2 Bpeak g √ µ0 3 4 kw Nph 2 −3 1.45 9.3 × 10 π 2×7 2 √ = 218 A µ0 3 4 0.91 × 280 2 Problem 4.27 part (a): Defining β = 2π/wavelength Φp = w Z π/β Bpeak cos βxdx = 0 2wBpeak = 1.48 mWb β part (b): Since the rotor is 5 wavelengths long, the armature winding will link 10 poles of flux with 10 turns per pole. Thus, λpeak = 100Φp = 0.148 Wb. part (c): ω = βv and thus Vrms = ωλpeak √ = 34.6 V, rms 2 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 56 PROBLEM SOLUTIONS: Chapter 5 Problem 5.1 Basic equations are T ∝ ΦR Ff sin δRF . Since the field current is constant, Ff is constant, Note also that the resultant flux is proptoortional to the terminal voltage and inversely to the frequency ΦR ∝ Vt /f . Thus we can write T ∝ Vt sin δRF f P = ωf T ∝ Vt sin δRF part part part part (a): (b): (c): (d): Reduced to 31.1◦ Unchanged Unchanged Increased to 39.6◦ Problem 5.2 part (a): The windings are orthogonal and hence the mutual inductance is zero. part (b): Since the two windings are orthogonal, the phases are uncoupled and hence the flux linkage under balanced two-phase operation is unchanged by currents in the other phase. Thus, the equivalent inductance is simply equal to the phase self-inductance. Problem 5.3 1 Lab = − (Laa − Lal ) = −2.25 mH 2 Ls = 3 (Laa − Lal ) + Lal = 7.08 mH 2 Problem 5.4 part (a): Laf = √ 2 Vl−l,rms √ = 79.4 mH 3ωIf part (b): Voltage = (50/60) 15.4 kV = 12.8 kV. Problem 5.5 part (a): The magnitude of the phase current is equal to Ia = 40 × 103 √ = 59.1 A 0.85 × 3 460 and its phase angle is − cos−1 0.85 = −31.8◦ . Thus WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 57 ◦ Iâ = 59.1e−j31.8 Then ◦ 460 Êaf = Va − jXs Iâ = √ − j4.15 × 59.1e−j31.8 = 136 − 56.8◦ V 3 The field current can be calculated from the magnitude of the generator voltage √ 2Eaf If = = 11.3 A ωLaf part (b): Êaf = 266 − 38.1◦ V; If = 15.3 A part (c): Êaf = 395 − 27.8◦ V; If = 20.2 A Problem 5.6 The solution is similar to that of Problem 5.5 with the exception that the sychronous impedance jXs is replaced by the impedance Zf + jXs . part (a): Êaf = 106 − 66.6◦ V; If = 12.2 A part (b): Êaf = 261 − 43.7◦ V; If = 16.3 A part (c): Êaf = 416 − 31.2◦ V; If = 22.0 A Problem 5.7 part (a): Laf = √ 2 Vl−l,rms √ = 49.8 mH 3ωIf part (b): 600 × 103 Iâ = √ = 151 A 3 2300 Êaf = Va − jXs Iâ = 1.77 − 41.3◦ V √ 2Eaf If = = 160 A ωLaf WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 58 part (c): See plot below. Minimum current will when the motor is operating at unity power factor. From the plot, this occurs at a field current of 160 A. Problem 5.8 part (a): Zbase = 2 (26 × 103 )2 Vbase = = 0.901 Ω Pbase 750 × 106 Ls = Xs,pu Zbase = 4.88 mH ω Lal = Xal,pu Zbase = 0.43 mH ω part (b): part (c): Laa = 2 (Ls − Lal ) + Lal = 3.40 mH 3 Problem 5.9 part (a): SCR = AFNL = 0.520 AFSC part (b): Zbase = (26 × 103 )2 /(800 × 106 ) = 0.845 Ω Xs = 1 = 2.19 pu = 1.85 Ω SCR part (c): Xs,u = AFSC = 1.92 pu = 1.62 Ω AFNL, ag WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 59 Problem 5.10 part (a): SCR = AFNL = 1.14 AFSC part (b): Zbase = 41602 /(5000 × 103 ) = 3.46 Ω Xs = 1 = 1.11 pu = 3.86 Ω SCR part (c): Xs,u = AFSC = 0.88 pu = 3.05 Ω AFNL, ag Problem 5.11 No numerical solution required. Problem 5.12 part (a): The total power is equal to S = P /pf = 4200 kW/0.87 = 4828 kVA. The armature current is thus 4828 × 103 (cos−1 0.87) = 670 29.5◦ A Iâ = √ 3 4160 Defining Zs = Ra + jXs = 0.038 + j4.81 Ω 4160 |Eaf | = |Va − Zs Ia | = | √ − Zs Ia | = 4349 V, line − to − neutral 3 Thus If = AFNL 4349 √ 4160/ 3 = 306 A part (b): If the machine speed remains constant and the field current is not reduced, the terminal voltage will increase to the value corresponding to 306 A of field current on the open-circuit saturation characteristic. Interpolating the given data shows that this corresponds to a value of around 4850 V line-to-line. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 60 Problem 5.13 Problem 5.14 At rated √ power, unity power factor, the armature current will be Ia = 5000 kW/( 3 4160 V) = 694 A. The power dissipated in the armature winding will then equal Parm = 3 × 6942 × 0.011 = 15.9 kW. The field current can be found from 4160 |Eaf | = |Va − Zs Ia | = | √ − Zs Ia | = 3194 V, line-to-neutral 3 and thus If = AFNL 3194 √ 4160/ 3 = 319 A At 125◦ C, the field-winding resistance will be 234.5 + 125 Rf = 0.279 = 0.324 Ω 234.5 + 75 and hence the field-winding power dissipation will be Pfield = If2 Rf = 21.1 kW. The total loss will then be Ptot = Pcore + Parm + Pfriction/windage + Pfield = 120 kW Hence the output power will equal 4880 kW and the efficiency will equal 4880/5000 = 0.976 = 97.6%. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 61 Problem 5.15 part (a): part (b): AFNL = 736 A. AFSC = 710 A. part (c): (i) SCR = 10.4, (ii) Xs = 0.964 per unit and (iii) Xs,u = 1.17 per unit. Problem 5.16 For Va = 1.0 per unit, Eaf,max = 2.4 per unit and Xs = 1.6 per unit Qmax = Eaf,max − Va = 0.875 per unit Xs Problem 5.17 part (a): Zbase = Xs = 2 Vbase = 5.29 Ω Pbase 1 = 0.595 per-unit = 3.15 Ω SCR WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 62 part (b): Using generator convention for current part (c): Eaf = 150 = 0.357 per-unit 420 For Va = 1.0 per-unit, Eaf − Va Iâ = = 1.08 90◦ per-unit = 1.36 90◦ kA jXs using Ibase = 1255 A. part (d): It looks like an inductor. part (e): Eaf = 700 = 1.67 per-unit 420 For Va = 1.0 per-unit, Eaf − Va = 1.12 − 90◦ per-unit = 1.41 − 90◦ kA Iâ = jXs In this case, it looks like a capacitor. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 63 Problem 5.18 Problem 5.19 part (a): It was underexcited, absorbing reactive power. part (b): It increased. part (c): The answers are the same. Problem 5.20 part (a): Xs = 226 = 0.268 per-unit 842 part (b): P = 0.875 and S = P/0.9 = 0.972, both in per unit. The powerfactor angle is − cos−1 0.9 = −25.8◦ and thus Iâ = 0.875 − 25.8◦ . Êaf = Va + jXs Iâ = 1.15 11.6◦ per-unit The field current is If = AFNL|Êaf | = 958 A. The rotor angle is 11.6◦ and the reactive power is Q = S 2 − P 2 = 4.24 MVA part (c): Now |Eaf | = 1.0 per unit. P Xs −1 δ = sin |Eaf | = 13.6◦ Va and thus Êaf = 1.0 13.6◦ . Êaf − Va = 0.881 6.79◦ Iâ = jXs Q = Imag[Va Iâ∗ ] = −0.104 per-unit = −1.04 MVAR WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 64 Problem 5.21 Êaf − Va Va Eaf Iâ = =j + (sin δ − j cos δ) jXs Xs Xs The first term is a constant and is the center of the circle. The second term is a circle of radius Eaf/Xs . Problem 5.22 part (a): (i) (ii) Vt = V∞ = 1.0 per unit. P = 375/650 = 0.577 per unit. Thus δt = sin−1 P X∞ Vt V∞ = 12.6◦ WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 65 and Vt ejδt − V∞ Iâ = = 0.578 3.93◦ per-unit jX∞ √ Ibase = Pbase /( 3 Vbase ) = 15.64 kA and thus Ia = 9.04 kA. (iii) The generator terminal current lags the terminal voltage by δt /2 and thus the power factor is pf = cos−1 δt /2 = 0.998 lagging (iv) |Êaf | = |V∞ + j(X∞ + Xs )Iâ | = 1.50 per-unit = 36.0 kV,line-to-line part (b): (i) Same phasor diagram (ii) Iâ = 0.928 6.32◦ per-unit. Ia = 14.5 kA. (iii) pf = 0.994 lagging (iv) Eaf = 2.06 per unit = 49.4 kV, line-to-line. Problem 5.23 part (a): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 66 part (b): part (c): Problem 5.24 part (a): From the solution to Problem 5.15, Xs = 0.964 per unit. Thus, with V∞ = Eaf = 1.0 per unit WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 67 Pmax = V∞ Eaf = 1.04 per-unit Xs noindent Hence, full load can be achieved. This will occur at Xs −1 δ = sin = 74.6◦ Eaf Vinfty part (b): The generator base impedance is 1.31 Ω. Thus, X∞ = 0.14/1.31 = 0.107 per unit. Now Pmax = V∞ Eaf = 1.04 per-unit = 0.934 per-unit = 135 MW (X∞ + Xs Problem 5.25 Follwing the calculation steps of Example 5.9, Eaf = 1.35 per unit. Problem 5.26 Now Xd = .964 per unit and Xq = 0.723 per unit. Thus part (a): 2 1 V∞ 1 V∞ Eaf P = sin δ + − sin 2δ = 1.037 sin δ + 0.173 sin 2δ Xd 2 Xq Xd An iterative solution with MATLAB shows that maximum power can be achieved at δ = 53.6◦ . part (b): Letting XD = Xd + X∞ and XQ = Xq + X∞ 1 V2 1 V∞ Eaf sin δ + ∞ sin 2δ = 0.934 sin δ + 0.136 sin 2δ − P = X 2 XQ XD An iterative solution with MATLAB shows that maximum power that can be achieved is 141 Mw, which occurs at a power angle of 75◦ . Problem 5.27 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 68 Problem 5.28 Problem 5.29 Problem 5.30 For Eaf = 0, Pmax = Vt2 2 1 1 − Xq Xq = 0.21 = 21% This maximum power occurs for δ = 45◦ . Id = Iq = Vt cos δ = 0.786 per-unit Xd Vt sin δ = 1.09 per-unit Xq WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 69 and thus Ia = Id2 + Iq2 = 1.34 per unit. S = Vt Ia = 1.34 per-unit Hence Q= Problem 5.30 P = S 2 − P 2 = 1.32 per-unit V2 V∞ Eaf sin δ + ∞ Xd 2 1 1 − Xq Xd sin 2δ The generator will remain synchronized as long as Pmax > P . An iterative search with MATLAB can easily be used to find the minimum excitation that satisfies this condition for any particular loading. part (a): For P = 0.5, must have Eaf ≥ 0.327 per unit. part (b): For P = 1.0, must have Eaf ≥ 0.827 per unit. Problem 5.32 part (a): part (b): We know that P = 0.95 per unit and that P = V∞ Vt sin δt Xbus and that V̂t − V∞ Iâ = jXt It is necessary to solve these two equations simultaneously for V̂t = Vt δt so that both the required power is achieved as well as the specified power factor WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 70 angle with respect to the generator terminal voltage. This is most easily done iteratively with MATLAB. Once this is done, it is straightforward to calculate Vt = 1.02 per-unit; Eaf = 2.05 per-unit; δ = 46.6◦ Problem 5.33 part (a): Define XD = Xd + Xbus and XQ = Xq + Xbus . (i) Eaf,min = Vbus − XD = 0.04 per-unit Eaf,max = Vbus + XD = 1.96 per-unit (ii) part (b): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 71 part (c): Problem 5.34 f= 3000 × 6 n × poles = = 150 Hz 120 120 Problem 5.35 part (a): Because the load is resistive, we know that 4500 P =√ = 13.5 A 3Va 3192 √ part (b): We know that Eaf = 208/ 3 = 120 V. Solving Eaf = Va2 + (Xs Ia )2 Ia = for Xs gives 2 −V2 Eaf a = 3.41 Ω Xs = Ia part (c): The easiest way to solve this is to use MATLAB to iterate to find the required load resistance. If this is done, the solution is Va = 108 V (line-to-neutral) = 187 V (line-to-line). Problem 5.36 Iâ = Ea ωKa = Ra + Rb + jωLa Ra + Rb + jωLa Thus ωKa |Iâ | = = (Ra + Rb )2 + (ωLa)2 Ka a +Rb La 1 + RωL a Clearly, Ia will remain constant with speed as long as the speed is sufficient to insure that ω >> (Ra + Rb )/La WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 72 PROBLEM SOLUTIONS: Chapter 6 Problem 6.1 part (a): Synchronous speed is 1800 r/min. Therefore, s= 1800 − 1755 = 0.025 = 2.5% 1800 part (b): Rotor currents are at slip frequency, fr = s60 = 1.5 Hz. part (c): The stator flux wave rotates at synchronous speed with respect to the stator (1800 r/min). It rotates at slip speed ahead of the rotor (s1800 = 45 r/min). part (d): The rotor flux wave is synchronous with that of the stator. Thus it rotatesat synchronous speed with respect to the stator (1800 r/min). It rotates at slip speed ahead of the rotor (s1800 = 45 r/min). Problem 6.2 part (a): The slip is equal to s = 0.89/50 = 0.0178. The synchronous speed for a 6-pole, 50-Hz motor is 1000 r/min. Thus the rotor speed is n = (1 − s)1000 = 982 r/min part (b): The slip of a 4-pole, 60-Hz motor operating at 1740 r/min is s= 1800 − 1740 = 0.0333 = 3.33% 1800 The rotor currents will therefore be at slip frequency fr = 60 ∗ 0.0333 = 2 Hz. Problem 6.3 part (a): The synchronous speed is clearly 1200 r/min. Therefore the motor has 6 poles. part (b): The full-load slip is s= Hz. 1200 − 1112 = 0.0733 = 7.33% 1200 part (c): The rotor currents will be at slip frequency fr = 60 ∗ 0.0733 = 4.4 part (d): The rotor field rotates at synchronous speed. Thus it rotates at 1200 r/min with respect to the stator and (1200-1112) = 88 r/min with respect to the rotor. Problem 6.4 part (a): The wavelenth of the fundamental flux wave is equal to the span of two poles or λ = 4.5/12 = 0.375 m. The period of the applied excitation is T = 1/75 = 13.33 msec. Thus the synchronous speed is WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 73 vs = λ = 28.1 m/sec = 101.3 km/hr T part (b): Because this is an induction machine, the car in this case) will never reach synchronous speed. part (c): s= 101.3 − 95 = 0.0622 = 6.22% 101.3 The induced track currents will be a slip frequency, f = s75 = 4.66 Hz. part (d): For a slip of 6.22% and a car velocity of 75 km/hr, the synchronous velocity must be vs = 75 = 80.0 km/hr 1−s Thus the electrical frequency must be 75 f = 80 = 59.2 Hz 101.3 and the track currents will be at a frequency of sf = 3.68 Hz. Problem 6.5 part (a): For operation at constant slip frequency fr , the applied electrical frequency fe is related to the motor speed in r/min n as poles fe = n + fr 120 and thus, since the slip frequency fr remains constant, we see that the applied electrical frequency will vary linearly with the desired speed. Neglecting the voltage drop across the armature leakage inductance and winding resistance, the magnitude of the armature voltage is proportional to the air-gap flux density and the frequency. Hence the magnitude of the armature voltage must vary linearly with electrical frequency and hence the desired speed. part (b): The electrical frequency of the rotor currents is equal to the slip frequency and hence will remain constant. Since the rotor will be operating in a constant flux which varies at a constant frequency, the magnitude of the rotor currents will be unchanged. part (c): Because the rotor air-gap flux density and the rotor currents are unchanged, the torque will remain constant. Problem 6.6 part (a): Since the torque is proportional to the square of the voltage, the torque-speed characteristic will simply be reduced by a factor of 4. part (b): Neglecting the effects of stator resistance and leakage reactance, having both the voltage and frequency maintains constant air-gap flux. Hence WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 74 the torque-speed characteristic looks the same as the original but the synchronous speed is halved. Problem 6.7 part (a): Four poles. part (b): Counterclockwise part (c): 1800 r/min part (d): Four poles part (e): No. There will be dc flux linking the induction-motor rotor windings but there will be no resultant voltage at the slip rings. Problem 6.8 part (a): 1500 r/min part (b): The induction motor rotor is rotating at 1500 r/min in the clockwise direction. Its stator flux wave is rotating at 3000× (2/poles) = 1000 r/min in the counterclockwise direction. Thus, the rotor sees a flux wave rotating at 2500 r/min. Noting that a flux wave rotating at 1000 r/min would produce 50-Hz voltages at the slip rings, we see that in this case the rotor frequency will be fr = 50 × (2500/1000) = 125 Hz. part (c): Now the stator flux wave will rotate at 1000 r/min in the clockwise direction and the rotor will see a flux wave rotating at 500 r/min. The induced voltage will therefore be at a frequency of 25 Hz. Problem 6.9 part (a): R1 will decrease by a factor of 1.04 to 0.212 Ω. part (b): Xm will increase by a factor of 1/.85 to 53.8 Ω. part (c): R2 will decrease by a factor of 3.5/5.8 to 0.125 Ω. part (d): All values will decrease by a factor of 3. Problem 6.10 This problem can be solved by direct substitution into the equations in chapter 6, which can in-turn be easily implemented in MATLAB. The following table of results was obtained from a MATLAB script which implemented the equivalent-circuit equations assuming the core-loss resistance Rc is in parallel with the magnetizing reactance. Rc was calculated as Rc = slip [%] speed [r/min] Tout [N·m] Pout [kW] Pin [kW] power factor efficiency [%] Problem 6.11 part (a): 1741 r/min 4602 = 962 Ω 220 1.0 1782 8.5 8.5 45.8 0.81 93.3 2.0 1764 16.5 16.5 89.6 0.87 94.4 3.0 1746 23.4 23.4 128 0.85 93.8 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 75 part (b): 1799 r/min part (c): part (d): Problem 6.12 For a speed of 1725 r/min, Pout = 426, kW, Pin = 457 kW, pf = 0.751 lagging and η = 93.3 %. Problem 6.13 It is necessary to find find the value of R2 . This can be easily done by writing a MATLAB script to iteratively find that value of R2 which full-load internal torque at a slip of 3.5%. The result is R2 = 0.0953 Ω. Once this is done, the same MATLAB script can be used to sustitute the machine parameters into the equations of chapter 6 to find Tmax = 177 N·m at a slip of 18.2% and Tstart = 71.6 N·m. Problem 6.14 This problem is readily solved once the value of R2 has been found as discussed in the solution to Problem 6.13. The impedance of the feeder must be added in series with the armature resistance R1 and leakage reactance X1 . A MATLAB script can then be written to find the desired operating point. The WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 76 result is that the motor achieves rated output at a slip of 3.67% and a terminal voltage of 221.6 V, line-to-line. Problem 6.15 part (a): For R1 = 0, R1,eq = 0 and thus from Eq. 6.34 R2 = (X1,eq + X2 ) smaxT From Eq. 6.36, Tmax = 2 0.5nph V1,eq ωs (X1,eq + X2 ) and from Eq.6.33 with s = 1 Tstart = Noting that 2 nph V1,eq R2 ωs [R22 + (X1,eq + X2 )2 ] Tmax 2.20 = = 1.63 Tstart 1.35 we can take the ratio of the above equations Tmax = 1.63 = Tstart R22 2 (X1,eq 2 + + X2 ) = R2 (X1,eq + X2 ) R2 X1,eq +X2 2 +1 R2 X1,eq +X2 From Eq.6.34, with Req,1 = 0, smaxT = R2 /(X1,eq + X2 ). Hence 0.5(s2maxT + 1) = 1.63 smaxT which can be solved to give smaxT = 0.343 = 34.3%. part (b): From Eq. 6.33 with Req,1 = 0 and with s = srated , Trated = 2 nph V1,eq (R2 /srated ) 2 ωs [(R2 /srated) + (X1,eq + X2 )2 ] and thus Tmax = 2.1 Trated = 0.5[(R2 /srated )2 + (Xeq,1 + X2 )2 ] (R2 /srated )(Xeq,1 + X2 ) = 0.5[1 + (smaxT /srated )2 ] smaxT /srated This can be solved to give WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 77 srated = 0.240smaxT = 0.0824 = 8.24% part (c): Iˆ2,start = Iˆ2,rated = V̂1,eq V̂1,eq = R2 + j(Xeq,1 + X2 ) (Xeq,1 + X2 )(smaxT + j) V̂1,eq V̂1,eq = R2 /srated + j(Xeq,1 + X2 ) (Xeq,1 + X2 )(smaxT /srated + j) Thus |Iˆ2,start | |4.16 + j| |smaxT /srated + j| = = 4.05 = 405% = ˆ |smaxT + j| |.343 + j| |I2,rated | Problem 6.16 Given Tmax = 2.3Tfl , smaxT = 0.55 and sfl = 0.087, start by taking the ratio of Eqs. 6.36 and 6.33 Tmax 0.5[(R1,eq + R2 /sfl )2 + (X1,eq + X2 )2 ] = Tfl 2 R1,eq + R1,eq + (X1,eq + X2 )2 (R2 /sfl ) Substituting Eq. 6.34 gives Tmax = Tfl 0.5sfl 2 sfl R1,eq R2 R1,eq R2 + + 1 sfl 2 + 1 smaxT 1 smaxT 2 Substituting given values and solving gives Req,1 = 1.315 R2 From Eq. 6.33 we can write  2  2 Req,1 Xeq,1 +X2 1 + + R2 sfl R2 Tstart   = sfl  2 2  Tfl Req,1 X +X eq,1 2 1 + R2 + smaxT R2 From Eq. 6.34, X1,eq + X2 R2 and thus we can solve for 2 = 1 smaxT 2 − R1,eq R2 2 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 78 Tstart = 1.26Tfl Problem 6.17 part (a): Using MATLAB to solve the equivalent-circuit equations, from the equivalent-circuit at a slip of 3.35%, the power applied to the shaft can be calculated to be 503.2 kW. Thus the rotational loss is 3.2 kW. Similarly, the input power to the equivalent circuit is 528.0 kW. Based upon an efficiency of 94%, the actual motor input power is 500 kW/0.94 = 531.9 kW. Thus, the core losses are equal to 531.9 - 528.0 = 3.9 kW. part (b): The equivalent circuit is solved in the normal fashion. For ease of calculation, the core loss can be accounted for by a resistor connected at the equivalent-circuit terminals (based upon the results of part (a), this corresponds to a resistance of 1.47 kΩ. The shaft input power is equal to the negative of the shaft power calculated from the equivalent circuit plus the rotational loss power. The electrical output power is equal to the negative of the input power to the equivalent circuit. The result is (using MATLAB): (i) Generator output power = 512 kW (ii) efficiency = 91.6% (iii) power factor = 0.89 part (c): Basically the same calculation as part (b). The impedance of the feeder must be added to armature impedance of the induction motor. The result is (using MATLAB): (i) Power supplied to the bus = 498 kW (ii) Generator output power = 508 kW Problem 6.18 Problem 6.19 2 2 part (a): Given I2,maxT R2 = 9.0I2,fl R2 . Thus I2,maxT = 3.0I2,fl . Ignoring R1 , R1,eq = 0 and we can write WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 79 Iˆ2 = V̂eq R2 /s + j(Xeq + X2 ) and thus Iˆ2,fl j(Xeq + X2 ) + R2 /smaxT = ˆ j(Xeq + X2 ) + R2 /sfl I2,maxT Substitution from Eq. 6.34 (X1,eq + X2 ) = R2 smaxT gives Iˆ2,fl Iˆ2,maxT j+1 j + smaxT /sfl = and thus I2,fl I2,maxT = √ 2 |j + 1| = |j + smaxT /sfl | 1 + (smaxT /sfl )2 Finally, we can solve for smaxT smaxT = 4.12sfl = 0.0948 = 9.48% part (b): Taking the ratio of Eqs. 6.36 and 6.33 with R1,eq = 0 and substitution of Eq. 6.34 gives 0.5[1 + (smaxT /sfl )2 ] 0.5[(R2 /sfl )2 + (X1,eq + X2 )2 ] Tmax = = 2.18 = Tfl (X1,eq + X2 )(R2 /sfl ) (smaxT /sfl ) In other words, Tmax = 2.18 per unit. part (c): In a similar fashion, one can show that 1 + (smaxT /sfl )2 Tstart = sfl = 0.41 Tfl 1 + s2maxT In other words, Tstart = 0.41 per unit. Problem 6.20 part (a): T ∝ I22 R2 /s. Thus Tstart = sfl Tfl I2,start I2,fl 2 = 1.32 and thus Tstart = 1.32 per unit. part (b): As in the solution to Problem 6.15, neglecting the effects of R1 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 80 |smaxT /sfl + j| |Iˆ2,start | = |smaxT + j| |Iˆ2,rated | This can be solved for smaxT smaxT = sfl 1 − (I2,start /Ifl )2 = 0.224 = 22.4% (sfl I2,start /Ifl )2 − 1 Again, from the solution to Problem 6.15, Tmax 0.5[1 + (smaxT /sfl )2 ] = = 3.12 Trated smaxT /sfl and thus Tmax = 3.12 per unit. Problem 6.21 part (a): Solving the equations of chapter 6, with s = 1 for starting, with MATLAB yields Istart = 233 A Tstart = 79.1 N·m part (b): (i) When the motor is connected in Y, the equivalent-circuit parameters will be three times those of the normal ∆ connection. Thus R1 = 0.135 Ω R2 = 0.162 Ω X1 = 0.87 Ω X2 = 0.84 Ω Xm = 28.8 Ω (ii) Istart = 77.6 A Tstart = 26.3 N·m Problem 6.22 part (a): 2 Prot = Pnl − 3Inl R1 = 2672 W part (b): The parameters are calculated following exactly the procedure found in Example 6.5. The results are: R1 = 1.11 Ω X1 = 3.90 Ω R2 = 1.34 Ω X2 = 3.90 Ω Xm = 168 Ω WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 81 part (c): Solving the equations of chapter 6 using the equivalent-circuit parameters of part (b) Ia = 29.1 A Pin = 106 kW power factor = 0.91 lagging Pout = 100 kW efficiency = 94.5% Problem 6.23 Because this is a blocked-rotor test, one can ignore the magnetizing reactance Xm . As a result, the motor input impedance can be approximated as Zin ≈ R1 + R2 + j(X1 + X2 ) R2 can be calculated from the blocked-rotor power and current R2 = Bbl 2 − R1 3Ibl which gives Motor 1: R2 = 0.174 Ω Motor 2: R2 = 0.626 Ω 2 The motor starting torque is proportional to Ibl R2 and thus the torque ratio is given by 2 (R2 )motor2 (I2 )motor2 Tmotor2 (I22 )motor2 (R2 )motor2 = 2 = Tmotor1 (I2 )motor1 (R2 )motor1 (R2 )motor1 (I22 )motor1 Thus, for the same currents, the torque will be simply proportional to the resistance ratio and hence Tmotor2 = 0.278 Tmotor1 From the given data, we see that for the same voltage, the current ratio will be (I2 )motor2 /(I2 )motor1 = 99.4/74.7 = 1.39 and hence Tmotor2 = 0.492 Tmotor1 Problem 6.24 Rotational loss = 3120 W R1 = 0.318 Ω R2 = 0.605 Ω X1 = 2.28 Ω X2 = 3.42 Ω Xm = 63.4 Ω WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 82 Problem 6.25 Neglecting R1 and hence Req,1 gives from Eq. 6.35 smaxT = R2 X1,eq + X2 and from Eq. 6.36 Tmax = 2 2 0.5nph V1,eq 0.5nphV1,eq smaxT = ωs (X1,eq + X2 ) ωs R2 If the frequency is reduced from 60 to 50 Hz, X1,eq + X2 will drop by a factor of 5/6 and hence smaxT will increase by a factor of 6/5 to smaxT = 18%, corresponding to a speed of 1000(1 − 0.18) = 820 r/min. Tmax will increase as (190/230)2(6/5) (Tmax )50 = 0.983 = (Tmax )60 5/6 or (Tmax )50 = 283% Problem 6.26 smaxT ∝ R2 . Therefore R2 = 1.1 = 2.07 Ω [(smaxT )Rext =1.1 /(smaxT )Rext =0 ] − 1 Problem 6.27 part (a): From the solution to Problem 6.15 0.5[1 + (smaxT /sfl )2 ] Tmax = Tfl smaxT /sfl Given that Tmax /Tfl = 2.25 and smaxT = 0.16, this can be solved for sfl = 0.0375 = 3.75%. part (b): The rotor rotor power dissipation at rated load is given by sfl = 2.9 kW Protor = Prated 1 − sfl part (c): From the solution to Problem 6.19 1 + (smaxT /sfl )2 Tstart = sfl = 0.70 Tfl 1 + s2maxT Rated torque is equal to 75 kW/ωm,fl where ωm,fl = 60π(1−sfl) = 181.4 rad/sec. Thus Trated = 413 N·m and Tstart = 0.70 per unit = 290 N·m. part (d): If the rotor resistance is doubled, the motor impedance will be the same if the slip is also doubled. Thus, the slip will be equal to s = 2sfl = 7.50%. part (e): The torque will equal to full-load torque. Thus T = 413 N·m. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 83 Problem 6.28 Problem 6.29 part (a): Protor = Prated sfl 1 − sfl = 3.63 kW part (b): From the solution to Problem 6.15 Tmax 0.5[1 + (smaxT /sfl )2 ] = Tfl smaxT /sfl Given that Tmax /Tfl = 3.10 and sfl = (1200 − 1158)/1200 = 0035, this can be solved for smaxT = 0.211 = 21.1%. This corresponds to a speed of 1200(1 − 0.211) = 947 r/min. part (c): Sufficient resistance must be inserted to increase smaxT from 0.211 to 1.0. Thus R2,tot = 0.17/.211 = 0.806 Ω and hence the added resistance must be Rext = 0.806 − 0.211 = 0.635 Ω. part (d): The applied voltage must be reduced by a factor of 5/6 to 383 V, line-to-line. part (e): From Eq. 6.35, smaxT = R2 /(X1,eq + X2 ). If the frequency decreases by a factor of 5/6, the reactances will also decrease by a factor of 5/6 and hence smaxT will increase by a factor of 6/5 to 0.042. Hence, the corresponding speed will be 1000(1 − 0.042) = 958 r/min. Problem 6.30 If the impedance of the motor at starting is made equal to that of the motor at a slip of 5.6% the starting current will be equal to 200% of its rated value. This can be done by increasing the rotor resistance for 90/2 = 45 mΩ to R2,tot = 0.045 = 804 mΩ 0.056 and hence the requierd added resistance will be Rext = 804 − 45 = 759 mΩ. The starting torque under this condition will be 190% of the full-load torque. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 84 Problem 6.31 The synchronous speed of this motor is 3600/8 = 450 r/min (47.12 rad/sec). Thus its full-load speed is 450(1 − 0.041) = 431.6 r/min. The corresponding torque will be (250 × 103 )[47.12(1 − 0.041)] = 5.53 × 103 N·m. At a speed of 400 r/min, the torque will be 5.53 × 103 (400/431.6)2 = 4.75 × 103 N·m. With no external resistance, the slope of the torque-speed characteristic is thus 5.53 × 103 /431.6 = 12.81. The slope of the desired torque-speed characteristic is 4.75 × 103 /400 = 11.88. Since the initial slope of the torque-speed characteristic is inversely proportional to the rotor resistance, the total rotor resistance must be 12.81 Rtot = 24.5 = 26.4 mΩ 11.88 Therefore the required added resistance is 26.4 − 24.5 = 1.9 mΩ. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 85 PROBLEM SOLUTIONS: Chapter 7 Problem 7.1 part (a): ωm ∝ Va . part (b): ωm ∝ I1f part (c): ωm will be constant. Problem 7.2 part (a): For constant terminal voltage, the product nIf (where n is the motor speed) is constant. Hence, since If ∝ 1/Rf Rf Rf + 5 = 1180 1250 and hence Rf = 84.2 Ω. part (b): 1380 r/min Problem 7.3 Check this part (a): ωm halved; Ia constant part (b): ωm halved; Ia doubled part (c): ωm halved; Ia halved part (d): ωm constant; Ia doubled part (e): ωm halved; Ia reduced by a factor of 4. Problem 7.4 part (a): Rated armature current = 25 kW/250-V = 100 A. part (b): At 1200 r/min, Ea can be determined directly from the magnetization curve of Fig. 7.27. The armature voltage can be calculated as Va = Ea + Ia Ra and the power output as Pout = Va Ia . With Ia = 100 A If [A] 1.0 2.0 2.5 Ea [V] 150 240 270 Va [V] 164 254 284 Pout [kW] 16.4 25.4 28.4 part (c): The solution proceeds as in part (b) but with the generated voltage equal to 900/1200 = 0.75 times that of part (b) If [A] 1.0 2.0 2.5 Ea [V] 112 180 202 Va [V] 126 194 216 Pout [kW] 12.6 19.4 21.6 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 86 Problem 7.5 part (a): part (b): (i) (ii) WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 87 Problem 7.6 part (a): Pshaft = Ea Va − Ea Ra and thus Va2 − 4Pshaft Ra Ea = 2 The motor speed n can then be found from Ea n = 1200 r/min 1.67 × 1200 Va + Here is the desired plot, produced by MATLAB part (b): The solution for Ea proceeds as in part (a). With the speed constant at 1200 r/min (and hence constant ωm ), solve for If as If = Ea Kf where Kf = 150D V/A. Here is the desired plot, produced by MATLAB. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 88 Problem 7.7 The solution is similar to that of Problem 7.6 with the exception that the assumed straight-line magnetization characteristic is replaced by the non-linear characteristic of Fig. 7.27. MATLAB, with the ’spline()’ function used to represent the non-linear characteristic of Fig. 7.27, then produces the following plots. part (a): part (b): Problem 7.8 part (a): From the load data, the generated voltage is equal to 254 + 62.7 × 0.175 = 265 A. From the magnetizing curve (using the ’spline()’ function of MATLAB), the corresponding field current is 1.54 A. Hence the demagnetizing effect of this armature current is equal to (1.95 − 1.54)500 = 204 A-turns/pole. part (b): At the desired operating point, the generator output power will be 250 V × 61.5 A = 15.4 kW. Therefore, the motor speed will be 15.4 = 1139 r/min n = 1195 − 55 15 Because the machine terminal voltage at no load must equal 230 V, from the magnetizing curve we see that the shunt field under this operating condition WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 89 must equal 1.05 A and hence the shunt field resistance must be 219 Ω. Hence, under this loading condition, with a terminal voltage of 250 V, the armature voltage will be 250 + 61.5 × 0.065 = 250.8 V, the shunt field current will equal 250.8/219 = 1.15 A and thus the armature current will equal 61.5 + 1.15 = 62.7 A. The generated voltage can now be calculated to be 250.8 + 62.7(0.175) = 286 V. The corresponding voltage on the 1195 r/min mag curve will be Ea = 286(1195/1139) = 285 V and hence the required net field ampere-turns is (using the MATLAB ‘spline()’ function) 1042 A-turns. The shunt-field ampere-turns is 1.15 × 500 = 575 A-turns, the demagnetizing armature amp-turns are 204 Aturns and hence the required series turns are Ns = 1042 − (575 − 204) = 10.6 ≈ 11 turns 61.5 Problem 7.9 From the given data, the generated voltage at Ia = 90A and n(90) = 975 r/min is Ea (90) = Va − Ia (Ra + Rs ) = 230 − 90(0.11 + 0.08) = 212.9 V Similarly, the generated voltage at Ia = 30 A is Ea (30) = 230 − 30(0.11 + 0.08) = 224.3 V Since Ea ∝ nΦ Ea (30) = Ea (90) n(30) n(90) Φ(30) Φ(90) Making use of the fact that Φ(30)/Φ(90) = 0.48, we can solve for n(30) Ea (30) Φ(90) n(30) = n(90) = 2140 r/min Ea (90) Φ(30) Problem 7.10 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 90 Problem 7.11 part (a): For constant field current, and hence constant field flux, constant torque corresponds to constant armature current. Thus for speeds up to 1200 r/min, the armature current will remain constant. For speeds above 1200 r/min, ignoring the voltage drop across the armature resistance, the motor speed will be inversely proportional to the field current (and hence the field flux). Thus the armature current will increase linearly with speed from its value at 1200 r/min. Note that as a practical matter, the armature current should be limited to its rated value, but that limitation is not considered in the plot below. part (b): In this case, the torque will remain constant as the speed is increased to 1200 r/min. However, as the field flux drops to increase the speed above 1200 r/min, it is not possible to increase the armature current as the field flux is reduced to increase the speed above 1200 r/min and hence the torque track the field flux and will decrease in inverse proportion to the change in speed above 1200 r/min. Problem 7.12 part (a): With constant terminal voltage and speed variation obtained by field current control, the field current (and hence the field flux) will be inversely proportional to the speed. Constant power operation (motor A) will then require WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 91 constant armature current. Constant torque (motor B) will require that the armature current variation be proportional to the motor speed. Thus motor A: Ia = 125 A motor B: Ia = 125(500/1800) = 34.7 A part (b): motor A: Ia = 125 A motor B: Ia = 125(1800/125) = 450 A part (c): Under armature voltage control and with constant field current, the speed will be proportional to the armature voltage. The generated voltage will be proportional to the speed. Constant-power operation (motor A) will require aramture current that increases inversely with speed while constant torque operation (motor B) will require constant armature current. For the conditions of part (a): motor A: Ia = 125(1800/125) = 450 A motor B: Ia = 125 A For the conditions of part (b): motor A: Ia = 125(500/1800) = 34.7 A motor B: Ia = 125 A Problem 7.13 ωm = Va − Ia Ra Ea = K a Φd K a Φd Ia = T K a Φd Thus 1 ωm = K a Φd T Ra Va − K a Φd The desired result can be obtained by taking the derivative of ωm with Φd dωm dΦd = = = 2T Ra 1 − Va Ka Φ2d Ka Φd 1 (2Ia Ra − Va ) Ka Φ2d 1 (Va − 2Ea ) Ka Φ2d From this we see that for Ea > 0.5Va , dωa /dΦd < 0 and for Ea < 0.5Va , dωa /dΦd > 0. Q.E.D. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 92 Problem 7.14 part (a): Synchronous machine: 30 × 103 Ia,ac = √ = 37.7 A 3 460 √ Eaf = |Va,ac + jXs Ia,ac | = |460/ 3 + j5.13 × 37.7| = 328.4 V, l − n DC machine: P = Ea Ia,dc = 30 kW Ea = Va,dc − Ia,dc Ra Thus, Ea2 = Va,dc + 2 Va,dc − 4P Ra 2 = 226 V part (b): Increase the dc-motor field excitation until Ea = Va,dc = 230 V, in which case the dc motor input current will equal zero and it will produce no shaft power. The ac machine will operate at a power angle of zero and hence its terminal current will be Ia,ac = Eaf − V a, ac = 12.2 A Xs part (c): If one further increases the dc-machine field excitation the dc machine will act as a generator. In this case, defining the dc generator current as positive out of the machine, P = Ea Ia,dc = 30 kW Ea = Va,dc + Ia,dc Ra Thus, Ea2 = Va,dc + 2 Va,dc + 4P Ra 2 = 226 V and Ia,dc = Ea − Va,dc = 128 A Ra WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 93 The ac machine will now be operating as a motor. The armature current will be the negative of that of part (a) and hence the power factor will be unity. Its magnitude will be 37.7 A. Problem 7.15 First find the demagnetizing mmf. At rated load, Ea = Va − Ia Rtot = 600 − 250 × 0.125 = 568.8 V Using the MATLAB ‘spline’ function, the corresponding field current on the 400 r/min magnetizing curve is If = 232 A Thus, the demagnetizing mmf at a current of 250 A is equal to 250 − 232 = 18 A and in general, the effective series-field current will be equal to 2 Ia Is,eff = Ia − 18 250 For a starting current of 460 A, the effective series field current will thus equal 399 A. Using the MATLAB ‘spline()’ function, this corresponds to a generated voltage of 474 V from the 400 r/min magnetization curve. The corresponding torque (which will be the same as the starting torque due to the same flux and armature current) can then be calculated as T = 474 × 560 Ea Ia = 5200 N · m = ωm 400(π/30) Problem 7.16 At no load, Ea,nl = 230 − 6.35 × 0.11 = 229.3 V. At full load, Ea,fl = 230 − 115 ∗ 0.11 = 217.4 V. But, Ea ∝ nΦ, thus Φnl 217.4 Ea,fl 1 nfl = nnl = 2150 = 2168 r/min Ea,nl Φfl 229.3 0.94 Problem 7.17 The motor power is given by P = Ea Ia , where Ea = Ka Φd ωm and where, from Eq. 7.3 Ka = 4 × 666 poles Ca = = 212 2πm 2π × 2 Thus, for Φd = 0.01, Ea = Ka Φd ωm = 2.12ωm. Ia = Vt − Ea Ra WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 94 Using MATLAB and its ‘spline()’ function to represent the fan characteristics, an iterative routine can be written to solve for the operating point (the intersection of the motor and fan characteristics). The result is that the motor will operate at a speed of 999 r/min and an output power of 8.39 kW. Problem 7.18 part (a): Assuming negligible voltage drop across the armature resistance at no load, the field current can be found from the 1300 r/min magnetization curve by setting Ea = 230 V. This can be most easily done using the MATLAB ‘spline()’ function. The result is If = 1.67 A. This corresponds to Nf If = 2500 a·turns of mmf. part (b): At rated load, Ea = Va − Ia Ra = 230 − 46.5 × 0.17 = 222.1 V. From the no-load, 1300 r/min magnetization curve, the corresponding field current is 1.50 A (again obtained using the MATLAB ‘spline()’ function). Thus, the effective armature reaction is Armature reaction = (1.67 − 1.5) A × 1500 turns/pole = 251 A · turns/pole part (c): With the series field winding, Rtot = Ra + Rs = 0.208 Ω. Thus, under this condition, Ea = Va −Ia Ra = 220.3. This corresponds to a 1300 r/min generated voltage of 236.7 V and a corresponding field current (determined from the magnetization curve using the MATLAB ‘spline()’ function) of 1.84 A, corresponding to a total of 2755 A·turns. Thus, the required series field turns will be Ns = 2755 − (2500 − 251) = 10.8 46.5 or, rounding to the nearest integer, Ns = 11 turns/pole. part (d): Now the effective field current will be Ieff = 2500 − 251 + 20 × 46.5 = 2.12 A 1500 From the 1300 r/min magnetization curve, Ea = 246.1 V while the actual Ea = Va − Rtot Ia = 220.3 V. Hence the new speed is 220.3 n = 1300 = 1164 r/min 246.1 Problem 7.19 part (a): At full load, 1185 r/min, with a field current of 0.554 A Ea = Va − Ia Rtot = 221.4 V where Rtot = 0.21 + 0.035 = 0.245 Ω. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 95 An 1825 r/min magnetization curve can be obtained by multiplying 230 V by the ratio of 1185 r/min divided by the given speed for each of the points in the data table. A MATLAB ‘spline()’ fit can then be used to determine that this generated voltage corresponds to a field-current of 0.527 A . Thus, the armature reaction is (0.554 − 0.527)2000 = 53.4 A·turns/pole. part (b): The full-load torque is 221.4 × 34.2 Ea Ia = 62.8 N · m = ωm 1185(π/30) T = part (c): The maximum field current is 230/310 = 0.742 Ω. The effective field current under this condition will therefore be Ieff = 2000 × 0.742 − 160 = 0.662 A 2000 From the 1185 r/min magnetization curve found in part (b), this corresponds to a generated voltage of 245 V. Thus, the corresponding torque will be T = Ea Ia 245 × 65 = 128 N · m = ωm 1185(π/30) part (d): With the addition of 0.05 Ω, the total resistance in the armature circuit will now be Rtot = 0.295 Ω. The required generated voltage will thus be Ea = Va − Ia Rtot = 219.6 V This corresponds to 219.6(1185/1050) = 247.8 V on the 1185 r/min magnetization curve and a corresponding effective field current of 0.701 A. As can be seen from the data table, a no-load speed of 1200 r/min corresponds to a field current of 0.554 A. Thus the series-field A·turns must make up for the difference between that required and the actual field current as reduced by armature reaction. Ns = = Nf (If,eff − If ) + Armature reaction Ia 2000(0.701 − 0.554) + 53.4 = 9.8 turns 35.2 Problem 7.20 part (a): From the demagnetization curve, we see that the shunt field current is 0.55 A since the no-load generated voltage must equal 230 V. The full-load generated voltage is Ea = Va − Ia Ra = 219.4 V and the corresponding field current (from the demagnetization curve obtained using the MATLAB ‘spline()’ function) is 0.487 A. Thus the demagnetization is equal to 2000(0.55 − 0.487) = 127 A·turns. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 96 part (b): The total effective armature resistance is now Rtot = 0.15+0.028 = 0.178 Ω. Thus, the full-load generated voltage will be Ea = Va − Ia Rtot = 217.4 V The net effective field current is now equal to 0.487+70.8(4/2000) = 0.628 A. The corresponding voltage at 1750 r/min (found from the magnetization curve using the MATLAB ‘spline()’ function) is 242.7 V and hence the full-load speed is 217.4 n = 1750 = 1567 r/min 242.7 part (c): The effective field current under this condition will be Ieff = 0.55 + 125(4/2000) − 230/2000 = 0.685 A From the 1750 r/min magnetization curve (using the MATLAB ‘spline()’ function), this corresponds to a generated voltage of 249 V. Thus, the corresponding torque will be T = 249 × 125 Ea Ia = = 170 N · m ωm 1750(π/30) Problem 7.21 part (a): For a constant torque load, changing the armature resistance will not change the armature current and hence Ia = 60 A. part(b): Ea = Va − Ra Ia Thus, without the added 1.0Ω resistor, Ea = 216 V and with it Ea = 156 V. Thus, Speed ratio = Problem 7.22 parts (a) and (b): 156 = 0.72 216 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 97 Operation in the fourth quadrant means that the motor torque is positive while the speed is negative. In this case the motor is acting as a generator and absorbing energy from the lowering load, which would otherwise accelerate due to the effects of gravity. part (c): -473 r/min Problem 7.23 part (a): At rated load, Ea = 230 − 122 times0.064 = 222 V. Thus, ratedload speed is 222 n = 1150 = 1133 r/min 230 part (b): The maximum value of the starting resistance will be required at starting. 230 = 2 × 122 = 244 Ra + Rmax and thus Rmax = 0.878 Ω. part (c): For each value of Rtot = Ra + Rext , the armature current will reach its rated value when the motor reaches a speed such that Ea = 230 − 122Rtot,old At this point Rtot will be reduced such that the armature current again reaches 122 A. Based upon this alogrithm, the external resistance can be controlled as shown in the following table: Step number 1 2 3 4 5 Rext [Ω] 0.878 0.407 0.170 0.051 0 Ea,min [V] 0 115 173 202 216 nmin [r/min] [V] 0 587 882 1030 1101 Ea,max [V] 115 173 202 216 - nmax [r/min] 587 882 1030 1101 - Problem 7.24 part (a): At no load, Ea,nl = Km ωm,nl = Va . Thus ωm,nl = 85 Va = 405 rad/sec = Km 0.21 Hence, the full-load speed is ωm,nl (30/π) = 3865 r/min. part (b): At zero speed, the current will be Ia = Va /Ra = 44.7 A and the corresponding torque will be T = Km Ia = 9.4 N·m. part (c): T = Km Ia = Km (Va − Km ωm ) Km (Va − Ea ) = Ra Ra WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 98 Here is the desired plot, obtained using MATLAB: Problem 7.25 part (a): At no load, ωm,nl = 11, 210(π/30) = 1174 rad/sec and Ea,nl = Va − Ia,nl Ra = 4.94 V. Thus Km = Ea,nl = 4.21 × 10−3 V/(rad/sec) ωm,nl part (b): The no load rotational losses are Prot,nl = Ea,nl Ia,nl = 62 mW part (c): At zero speed, the current will be Ia = Va /Ra = 1.09 A and the corresponding torque will be T = Km Ia = 4.6 mN·m. part (d): The output power versus speed characteristic is parabolic as shown below. An iterative MATLAB scripts can easily find the two desired operating points: 2761 r/min for which the efficiency is 24.3% and 8473 r/min for which the efficiency is 72.8%. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 99 Problem 7.26 No numerical solution required for this problem. Problem 7.27 Based upon the calculations of Problem 7.25, at 8750 r/min, the rotational losses will be 29.4 mW. Thus, the total required electromechanical power will be P = 779 mW. The generated voltage will be Ea = Km ωm = 3.86 V and the armature current will thus be Ia = P/Ea = 0.202 A. Thus the desired armature voltage will be Va = Ea + Ra Ia = 4.79 V WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 100 PROBLEM SOLUTIONS: Chapter 8 Problem 8.1 part (a): In this case, β = 45◦ = π/4 rad and Lmax = N 2 µ0 βRD = 96 mH 2g and there is a 15◦ overlap region of constant inductance. part (b): Tmax,1 = Lmax I12 = 6.1 × 10−2 I12 N · m 2β Tmax,1 = Lmax I22 = 6.1 × 10−2 I22 N · m 2β WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 101 part (c): i1 = i2 = 5 A; (i) ω = 0 Tnet = 0 (ii) ω = 45◦ Tnet = 0 (iii) ω = 75◦ Tnet = 1.53 N·m Problem 8.2 When a single phase is excited, magnetic circuit analysis can show that all the mmf drop occurs across the two air gaps associated with that phase. Thus, there is no additional mmf available to drive flux through the second phase. Problem 8.3 Same argument as in the solution of Problem 8.3. Problem 8.4 part (a) and (b): Lmax = DRαµ0 N 2 = 21.5 mH 2g WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 102 part (c): I0 = 2gB = 6.96 A µ0 N part (d): Tmax = I02 2 Lmax α/2 = 1.99 N · m WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 103 part (e): phase 1 ON: −120◦ ≤ θ ≤ −90◦ , −30◦ ≤ θ ≤ 0◦ , 60◦ ≤ θ ≤ 90◦ , 150◦ ≤ θ ≤ 180◦ phase 2 ON: −150◦ ≤ θ ≤ −120◦, −60◦ ≤ θ ≤ −30◦ , 30◦ ≤ θ ≤ 60◦ , 120◦ ≤ θ ≤ 150◦ phase 3 ON: −180◦ ≤ θ ≤ −150◦, −90◦ ≤ θ ≤ −60◦ , 0◦ ≤ θ ≤ 30◦ , 90◦ ≤ θ ≤ 120◦ part (f): The rotor will rotate 90◦ in 30 msec. n= (1/4) r = 7.14 r/sec = 429 r/min 35 msec The rotor will rotate in the clockwise direction if the phase sequence is 1 - 2 3 - 1 .... Problem 8.5 When the rotor is aligned with any given pole pair, it is clearly med-way between the other two pole pairs. Thus rotation in one direction will increase the inductance of one set of poles and decrease the inductance of the remaining set. Thus, depending on which of the remaining poles is excited, it is possible to get torque in either direction. Problem 8.6 The rotor will rotate 15◦ as each consecutive phase is excited. Thus, the rotor will rotate 1 revolution in 24 sequences of phase excitation or 8 complete sets of phase excitation. Thus, the rotor will rotate 1 revolution in 8 × 15 = 120! msec. Thus it will rotate at 1/0.12 = 8.33 r/sec = 500 r/min. Problem 8.7 part (a): If phase 1 is shut off and phase 2 is turned on, the rotor will move to the left by 2β/3 ≈ 4.29◦ . Similarly, turning off phase 2 and turning on phase 3 will cause the rotor to move yet another 4.29◦ . Thus, starting with phase 1 on, to move 21.4◦ /4.29◦ ≈ 5 steps, the sequence will be: 1 2 3 1 2 OFF OFF OFF OFF OFF 1 ON & 2 ON & 3 ON & 1 ON & 2 ON & 3 ON part (b): Clockwise is equivalent to rotor rotation to the right. The required phase sequence will be ... 1 - 3 - 2 - 1 - 3 - 2 .... The rotor will rotate ≈ 4.29◦/step and hence the rotor speed will be WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 104 125 r/min × 360◦ 1 step × = 1.05 × 104 steps/min r 4.29◦ Thus the required step time is time 1 min 60 sec = × = 5.72 msec/step step 8400 step min Problem 8.8 part (a): When phase 1 is energized, the rotor will be aligned as shown in the following figure: From the figure, we see that if phase 1 is turned off and phase 2 is energized, the rotor will rotate 4.61◦ degrees to the right (clockwise) to align with the phase-2 pole. Similarly, if phase 3 is excited after phase 1 is turned off, the rotor will rotate 4.61◦ degrees to the left (counterclockwise). part (b): 80 r/min × 360◦ 1 step = 6.25 × 103 steps/min × r 4.61◦ 60 sec 1 min time × = = 9.6 msec/step step 6.25 × 103 step min The required phase sequence will thus be ... 1 - 3 - 2 - 1 - 3 - 2 - 1 .... Problem 8.9 part (a): For time in which the current is building up i1 (t) = 100t A 0.005 + 57.5t WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 105 This expression is valid until time t = 2.22 msec, at which point i1 (t) = 1.67 A. part (b): i1 (t) = 0.22 − 200(t − 2.22 × 10−3 ) 0.05 + 57.5(4.44 × 10−3 ) − 7 This expression is valid until time t = 3.32 msec. part (c): Here are the desired plots The integral under the torque curve is 2.38 × 10−4 N·m·sec while the positive torque integral is 3.29 N·m·sec. Thus there is a 25.7% reduction in torque due to negative torque production during the current-decay period. Problem 8.10 part (a): For time in which the current is building up i1 (t) = 100t A 0.005 + 57.5t This expression is valid until time t = 2.22 msec, at which point i1 (t) = 1.67 A. part (b): i1 (t) = 0.22 − 250(t − 2.22 × 10−3 ) 0.05 + 57.5(4.44 × 10−3 ) − 7 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 106 This expression is valid until time t = 3.10 msec. part (c): Here are the desired plots The integral under the torque curve is 2.59 × 10−4 N·m·sec while the positive torque integral is 3.20 N·m·sec. Thus there is a 19.0% reduction in torque due to negative torque production during the current-decay period. Problem 8.11 part (a): The phase inductance looks like the plot of Problem 8.4, part (a), with the addition of the Lleak = 4.5 mH leakage inductance. Now Lmax = 21.5 + 4.5 = 26.0 mH. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 107 part (b): For −30◦ ≤ θ ≤ 0◦ 21.5 mH dL = = 20.5 mH/rad dθ π/3 rad ωm = 1750 r 2πrad 1min dθ = × × = 183 rad/sec dt min r 60sec dL dL = ωm = 3.76 Ω dt dθ The governing equation is v = iR + L di dL +i dt dt Noting that dL/dt >> R, we can approximate this equation as v≈ d(Li) dt and thus i(t) = v(t) dt L(t) Substituting v(t) = 75 V and L(t) = 4.5 × 10−3 + 3.76t then gives i(t) = 75 t 4.5 × 10−3 + 3.76t WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 108 which is valid over the range 0 ≤ t ≤ 5.71 msec, at which time i(t) = 16.5 A. Here is the desired plot: part (c): During this time, starting at time t = 5.71 msec, v(t) = −75 V and L( t) = 26.0 × 10−3 − 3.76(t − 5.71 × 10−3 ). Thus i(t) = 16.5 + −75 (t − 5.71 × 10−3 ) 26.0 × 10−3 − 3.76(t − 5.71 × 10−3 ) which reaches zero at t = 8.84 msec. Here is the plot of the total current transient. part (d): The torque is given by T = Here is the plot: i2 dL 2 dθ WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 109 Problem 8.12 part (a): The plot of Lθ is shown below Here, from Examples 8.1 and 8.3, Lleak = 5 mH and Lmax = 133 mH. part (b): The solution for −67.5◦ ≤ θ ≤ −7.5◦ (0 ≤ t ≤ 2.5 msec) is exactly the same as part (a) of Example 8.3 i(t) = 100t A 0.005 + 51.2t For −7.5◦ ≤ θ ≤ 7.5◦ (2.5 msec ≤ t ≤ 3.13 msec), dL/dt = 0 and thus v = iR + L di di ⇒ −100 = 1.5i + 0.133 dt dt This equation has an exponential solution with time constant τ = L/R = 88.7 msec. i = −66.7 + 68.6e−(t−0.0025)/0.0887 At t = 3.13 msec, i(t) = 1.39 A. Following time t = 3.13 msec, the solution proceeds as in Example 8.3. Thus i(t) = 1.468 − 100 − 3.13 × 10−3 0.005 − 51.2(t − 5.63 × 10−3 ) The current reaches zero at t = 4.25 msec. Here is the corresponding plot, produced by MATLAB WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 110 part (c): T = Problem 8.13 part (a): i2 dL 2 dθ WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 111 part (b): Inverter volt − ampere rating = 1.55 Net output power part (c): Pmech = 2968 W. Problem 8.14 part (a): Based upon the discussion in the text associated with Fig. 8.18, the following table can be produced: θm 0◦ 45◦ 90◦ 135◦ 180◦ 225◦ 270◦ 315◦ bit pattern 1000 1010 0010 0110 0100 0101 0001 1001 i1 I0 I0 0 −I0 −I0 −I0 0 I0 i2 0 I0 I0 I0 0 −I0 −I0 −I0 part (b): There will be 8 pattern changes per revolution. At 1200 r/min = 20 r/sec, there must be 160 pattern changes per second, corresponding to a time of 6.25 msec between pattern changes. Problem 8.15 part (a): The rotor will rotate 2◦ counter clockwise. part (b): The phase excitation will look like (with T = 41.7 msec): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 112 part (c): 8r 2880◦ 48◦ 2◦ = = = min min sec 41.7 msec The frequency will be f= 1 = 6 Hz 4T Problem 8.16 part (a): The displacement will be 360◦ /(3 × 14) = 8.571◦. part (b): There will be one revolution of the motor for every 14 cycles of the phase currents. Hence 900 r 1 min 14 cycles f= = 210 Hz min 60 sec r WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 113 PROBLEM SOLUTIONS: Chapter 9 Problem 9.1 part (a): Iˆmain = V̂ Zmain = 13.8 − 56.4◦ A V̂ Iâux = = 9.9 − 49.2◦ A Zaux part (b): We want the angle of the auxiliary-winding current to lead that ′ = Zaux + jXC of the main winding by 90c (π/2 rad). Thus, defining Zaux (XC = 1/ωC), we want ′ Zaux = tan−1 Im[Zaux ] − XC π = Zmain + Re[Zaux ] 2 Thus XC = 14.5 Ω and C = 183 µF. part (c): Iˆmain = V̂ Zmain = 13.8 − 56.4◦ A V̂ Iâux = ′ = 12.6 33.6◦ A Zaux Problem 9.2 The solution is basically the same as for Problem 9.1, but now with Zmain = 4.82 + j6.04 Ω and Zaux = 7.95 + j7.68 Ω and ω = 100π. part (a): Iˆmain = 15.5 − 51.4◦ A Iâux = 10.9 − 44.0◦ A part (b): C = 227 µF. part (c): Iˆmain = 15.5 − 51.4◦ A Iâux = 11.8 38.6◦ A Problem 9.3 No numerical solution required. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 114 Problem 9.4 Imain = 3.48 A power factor = 0.59 Pout = 132 W speed = 1719 r/min Torque = 0.732 N·m efficiency = 58.5 % Problem 9.5 The solution follows that of Example 9.2. Imain = 4.38 A power factor = 0.65 Pout = 204 W speed = 1724 r/min Torque = 1.13 N·m efficiency = 63.0 % Problem 9.6 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 115 Problem 9.7 part (a): From Eq. 4.6, the peak amplitude, in space and time, of the mmf waves are given by 4 kw Nph Fpeak = Ipeak π poles Thus Fmain,peak 4 = π 4 π 42 4 20.7 √ 2 = 391 A · turns and Faux,peak = 68 4 11.1 √ 2 = 340 A · turns part (b): The auxiliary winding current must be phase shifted by 90◦ from that of the main winding and the mmf amplitudes must be equal. Hence, Iaux should be increased to Nmain Iaux = Imain = 12.8 A Naux Problem 9.8 The internal torque is proportional to Rrmf − Rb and thus is equal to zero when Rf = Rb . From Example 9.2, 2 Xm,main 1 Rf = X22 sQ2,main + 1/(sQ2,main) and Rb = 2 Xm,main X22 1 (2 − s)Q2,main + 1/((2 − s)Q2,main ) We see that Rf = Rb if (2 − s)Q2,main = 1/(sQ2,main) or 1 s=1± 1+ Q2,main and thus n = ns (1 − s) = ±ns where ns is the synchronous speed in r/min. 1+ 1 Q2,main WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 116 Problem 9.9 The solution follows that of Example 9.3. part (a): Iα = 34.5 − 32.3◦ A, Iβ = 7.1 30.0◦ A part (b): Pmech = 6700 W Problem 9.10 part (a): Following the calculations of Example 9.3 with s = 1, Tmech = 14.8 N·m. part (b): Setting Vα = 230 V Vβ = 230ej90 ◦ V gives Tmech = 16.4 N·m. part (c): Letting V̂α = Vα and V̂β = jVβ gives Vf = Vα + jVβ ; 2 Vb = Vα − jVβ 2 Ib = Vb Vα − jVβ = Z 2Z Let Z = R1 + jX1 + Zf . Thus If = Vα + jVβ Vf ; = Z 2Z Rf (If2 − Ib2 ) Pgap,f − Pgap,b = = T = ωs ωs Rf |Z|2 Vα Vβ Clearly, the same torque would be achived if the phase voltages were each equal in magnitude to Vα Vβ . Problem 9.11 The impedance Z must be added to the impedances of the motor of Problem 9.9. The solution then proceeds as in Example 9.3. The terminal voltage can be found as V̂t,α = V̂α − Iˆα Z V̂t,β = V̂β − Iˆβ Z For V̂α = 235 0◦ ; V̂β = 212 78◦ a MATLAB analysis gives V̂t,α = 205 − 8.0◦ ; V̂t,β = 194 73◦ which is clearly more balanced than the applied voltage. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 117 Problem 9.12 part (a): slip s = 0.035 V̂f = 1 (V̂α − j V̂β ) = 214.8 − 12.5◦ V 2 V̂b = 1 (V̂α + j V̂β ) = 47.6 77.5◦ V 2 Zf and Zb can be calculated from Eqs. 9.4 and 9.5 with s = 0.035 Iˆf = V̂f = 2.99 − 64.0◦ R1 + jX1 + Zf Iˆb = V̂b = 4.48 0.7◦ R1 + jX1 + Zb Pgap,f = 2If2 Rf = 784 W Tgap = Pgap,b = 2Ib2 Rb = 65.9 W (Pgf − Pgb ) = 3.81 N · m ωs part (b): Repeating the analysis of part (a) with s = 1 gives Tstart = 12.0n·m. part (c): Now we have a two-phase machine operating under balanced twophase conditions. We can now apply the analysis of Section 6.5. jXm (R1 + jX1 ) V1,eq = V1 = 208 V R1 + j(X1 + Xm ) and R1,eq + jX1,eq = jXm in parallel with R1 + jX1 = 0.698 + j5.02 Ω. Thus smax,T = R2 2 R1,eq + (X1,eq + X2 )2 = 0.348 and Tmax =  1  ωs R 1,eq + 2 0.5nph V1,eq 2 R1,eq + (X1,eq + X2 )2   = 20.8 N · m part (d): Now we have a single-phase machine operating with Vα = 220 V and s = 0.04 Iˆα = Vα = 5.73 − 52.3◦ A (R1 + jX1 0.5(Zf + Zb ) WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 118 Pgap = 0.5Iα2 (Rf − Rb ) = 691 W Pmech = Pgap (1 − s) = 664 W and finally Pout = Pmech − Prot = 599 W part (e): Iˆf = Iˆb = 0.5Iˆα = 2.82 − 52.3◦ V̂f = (R1 + jX1 + Zf )Iˆf ; V̂b = (R1 + jX1 + Zb )Iˆb and thus V̂β = j(Vf − Vb ) = 0.5j Iˆα (Zf − Zb ) = 167 81.3◦ V In other words, the open-circuit voltage across the β winding will be 167 V. Problem 9.13 This problem can be solved using a MATLAB script similar to that written for Example 9.5. part (a): Tstart = 0.28 N·m. part (b): Imain = 19.3 A; Iaux = 3.2 A part (c): I = 21.3 A and the power factor is 0.99 lagging part (d): Pout = 2205 W part (e): Pin = 2551 W and η = 86.4% Problem 9.14 This problem can be solved using a MATLAB script similar to that written for Example 9.5. An iterative search gives C = 70.4 µF and an efficiency of 87.1%. Problem 9.15 This problem can be solved using a MATLAB script similar to that written for Example 9.5. An iterative search shows that the minimum capacitance is 80.9 µF. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 119 Problem 9.16 part (a): parts (b) and (c): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 120 PROBLEM SOLUTIONS: Chapter 10 Problem 10.1 part (a): part (b): Vrms = 1 T 0 T 2 (t) vR dt = 2 T T /4 0 4V0 t T 2 V0 dt = √ = 3.67 V 6 2 part (c): < pdiss >= Vrms /R = 9 mW. Problem 10.2 part (a): The diode does not turn on until the source voltage reaches 0.6 V, which occurs at time t = (0.6/4V0 )T = T /60. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 121 part (b): Vrms = 2 T T /4 T /60 4 × 8.4t T 2 dt = 3.43 V 2 part (c): < pdiss >= Vrms /R = 7.8 mW. Problem 10.3 Vrms = 2 T T /4 td 4V0 t T 2 32V02 dt = 3 1 − 43 td T 3 Problem 10.4 Problem 10.5 part (a): Peak VR = 310 V. part (b): Ripple voltage = 25.7 V. part (c): Time-averaged power dissipated in the load resistor = 177 W. part (d): Time-averaged power dissipated in the diode bridge = 0.41 W. Problem 10.6 If vs (t) ≥ 0, diode D1 is ON, diode D2 is off and the inductor current is governed by the following differential equation: L di + Ri = vs (t) dt of vs (t) < 0, diode D1 is off and diode D2 is on and the inductor current is governed by the differential equaion: L di + Ri = 0 dt A simple integration implemented in MATLAB produces the following plot: WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 122 Problem 10.7 Problem 10.8 part (a): Letting T = 2π/ω Vdc = 1 T T /2 V0 sin ωt = 0 V0 = 14.3 V π part (b): Idc = Vdc = 2.9 A R WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 123 part (c): part (d): Problem 10.9 part (a): Letting T = 2π/ω Vdc = 1 T T /2 td V0 sin ωt = V0 (1 + cos ωtd ) 2π part (b): Idc = V0 Vdc = (1 + cos ωtd ) R 2πR WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 124 part (c): Problem 10.10 part (a): Letting T = 2π/ω Vdc = 2 T T /2 td V0 sin ωt = V0 (1 + cos ωtd ) π part (b): Idc = part (c): V0 Vdc = (1 + cos ωtd ) R πR WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 125 part (d): Problem 10.11 part (a): (i) (ii) Vdc = 1 π 5π/4 V0 sin θ dθ = π/4 V0 V0 cos α2 = √ π π 2 (iii) Pload = Vdc Idc = V0 Idc √ π 2 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 126 part (b): (i) (ii) Vdc = 1 π 7π/4 V0 sin θ dθ = 3π/4 V0 V0 cos α2 = − √ π π 2 (iii) V0 Idc Pload = Vdc Idc = − √ π 2 The power is negative, hence energy is being extracted from the load. Problem 10.12 part (a) From Eq. 10.11 Idc = 2V0 = 18.3 A πR + 2ωLs and from Eq. 10.8 2Idc ωLs 1 −1 1− = 3.12 msec tc = cos ω V0 part (b): For Ls = 0 Idc = 2V0 = 23.6 A πR Problem 10.13 part (a): At 1650 r/min, the generated voltage of the dc motor is equal to 1650 Ea = 85 = 81.3 V 1725 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 127 The motor input power will then be Pin = Ia (Ea + Ia Ra ) = 665 W part (b): Vdc = 2V0 π √ 2 2 × 115 cos αd = 103.5 cos αd V cos αd = π Thus for Vdc = Ea + Ia (Ra + RL ) = 90.5 V, αd = 29.1◦ . Problem 10.14 The rated current of this motor is Irated = 1000 Prated = = 11.8 A Vrated 85 The controller must limit Idc to twice Irated or 23.6 A. Under this condition, Vdc = Ia (Ra + RL ) = 28.5 V. From part (b) of the solution to Problem 10.13, Vdc = 103.5 cos αd V and thus the controller must set αd = 74.0◦ . Problem 10.15 The required dc voltage is Vf = If Rf = 277 V. From Eq. 10.19, πVf Vl−l,rms = √ = 204 V, rms 3 2 Problem 10.16 The required dc voltage is Vf = If Rf = 231 V. From Eq. 10.20, πVf −1 √ αd = cos = 39.0◦ 3 2 Vl−l,rms Problem 10.17 part (a): The magnet resistance is sufficiently small that its voltage drop can be ignored while the magnet is being charged. The desired charge rate is di = 80 A25 sec = 3.2 A/sec dt Thus the required dc voltage will be Vdc = L di = 15.7 V dt WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 128 Thus αd = cos −1 πV √ dc 3 2 Vl−l,rms = cos−1 π 15.7 √ 3 2 × 15 = 39.3◦ part (b): Constant current simply requires a dc voltage of Vdc = RIdc = 3.6 × 10−3 × 80 = 0.29 V. Thus π 15.7 πVdc −1 √ √ αd = cos = cos−1 = 89.2◦ 3 2 Vl−l,rms 3 2 × 0.288 Problem 10.18 part (a): V1 2πt 2πt 2 T 8 DT /2 v(t) cos V0 cos dt = dt T 0 T T 0 T V0 sin πD = 51.5 V 4π = = part (b): Harmonic number 1 2 3 4 5 6 7 8 9 10 Peak amplitude [V] 51.5 0 6.6 0 12.7 0 2.8 0 5.7 0 Problem 10.19 part (a): 3 V3 = T A3 = 0 for D = 1/3 0 T v(t) cos 6πt T dt = 4V0 sin (3πD) 3π WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 129 part (b): Harmonic number 1 2 3 4 5 6 7 8 9 10 Peak amplitude [V] 55.1 0 0.007 0 11.0 0 7.9 0 0.007 0 Problem 10.20 part (a): Time period 0 ≤ ωt < αd + DT /2 αd + DT /2 ≤ ωt < π + αd − DT /2 π + αd − DT /2 ≤ ωt < π + αd + DT /2 π + αd + DT /2 ≤ ωt < 2π + αd − DT /2 2π + αd − DT /2 ≤ ωt < 2π S1 ON ON OFF OFF ON S2 OFF ON ON OFF OFF S3 ON OFF OFF ON ON part (b): By analogy to the solution of Problem 10.18, part (a) I1 = I0 sin πD 4π and by inspection φ1 = αd . part (c): p(t) =< i1 (t)vL (t) >= Va I1 Va I0 cos φ1 = cos αd 2 8π Problem 10.21 From Eq. 10.34 (iL )avg = [2D − 1]V0 = 17.65 A R From Eq. 10.29 (iL )min = − V0 R T 1 − 2e −T (1−D) τ + e− τ T (1 − e− τ ) = 17.45 A and from Eq. 10.20 (iL )max = V0 R T 1 − 2e −DT τ + e− τ T (1 − e− τ ) = 17.84 A Finally Ripple = (iL )max − (iL )min = 0.39 A S4 OFF OFF ON ON OFF WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 130 PROBLEM SOLUTIONS: Chapter 11 Problem 11.1 part (a): From the no-load data Kf = 120 Ea,nl = = 0.953 ωm,nl If,nl (1718π/30) × 0.7 Combining T = Ea Ia ωm and Va = Ea + Ia Ra gives Ea Thus = 0.5 Va + Va2 − 4ωm T Ra = 0.5 120 + 1202 − 4(1800π/30) × 15.2 × 0.145 = 116.4 V If = Ea = 0.648 A ωm K f and, defining If,max = 120/104 = 1.14 A, D= If If,max = 0.567 part (b): If = 0.782 A and D = 0.684. part (c): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 131 Problem 11.2 part (a): If = 0.645 A and D = 0.565. part (b): If = 0.784 A and D = 0.686. part (c): Problem 11.3 part (a): From part (a) of Problem 11.1, kf = 0.953. For Ea = 120 V and n = 1300 r/min (ωm = 1300π/30) and thus If,1 = Ea = 0.925 A ωm K f and D= If = 0.809 If,max where If,max = 1.14 A as found in Problem 11.1. part (b): If,2 = DIf,max = 0.686 A. ωm = Ea = 183.7 r/min If Kf and thus n = 30ωm /π. part (c): if (t) = If,2 + (If,1 − If,2 )e−t/τ = 0.686 + 0.239e−t/τ where τ = Lf /Rf = 35.2 msec. part (d): J dωm = Kf if (t)Ea = Kf if (t) dt where if (t) is as given in part (c). Va − Kf if (t)ωm Ra WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 132 Problem 11.4 part (a): Ea,nl = Va − Ra Inl = 239.7 V The rotational loss is given by Prot = Ea,nl Ia,nl = 374 W. Based upon If = Va /Rf = 1.81 A, ωm,nl = Ea,nl = 312.5 r/min If Kf and thus nnl = 30ωm,nl /π = 2984 r/min. part (b): part (c): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 133 part (d): Problem 11.5 part (a): First convert Km to SI units. Km = 2.18 × 10−4 1r/min V = 2.08 mV /(rad/sec) r/min π/30 rad/sec Tstall = 0.094 oz/cdotin = 6.64 × 10−4 N · m. At stall, Ia,stall = Tstall /Km = 0.319 A. Thus 3 Va = 9.41 Ω = Ra = Ia 0.319 π part (b): ωm,nl = nnl 30 = 1299 rad/sec. Thus Ea,nl = ωm,nl Km,nl = 2.70 V. Va − Ea,nl Ia,nl = = 31.5 mA Ra and thus the no-load rotational loss is Prot = Ea,nl Ia,nl = 85.3 mA part (c): WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 134 Problem 11.6 π part (a): ωm,nl = nnl 30 = 374.9 rad/sec. Ea,nl = Va − Ia,nl Ra = 24.0 V Km = Ea,nl = 63.9 mV/(rad/sec) ωm,nl part (b): Prot = Ea,nl Ia,nl = 11.3 W part (c): D 0.80 0.75 0.70 0.65 0.60 0.55 0.50 Ia [A] 13.35 12.70 12.05 11.40 10.70 10.05 9.30 r/min 3393 3179 2964 2749 2535 2320 2107 Pload [W] 293 261 231 203 176 151 127 Problem 11.7 The rotor acceleration is governed by the differential equation: J dωm = T = Km Ia dt Converted to kg·m2 , the moment of inertia is 4.52 × 10−9 kg·m2 . Thus, to get to the final speed ωm = 1.2 × 104 π/30 = 1257 rad/sec, t= (4.5 × 10−9 ) × 1257 Jωm = 27.3 msec = Km Ia (2.08 × 10−3 ) × 0.1 Problem 11.8 part (a): Ia,rated = Prated + Prot 1187 = 8.12 A = ωm,rated Km (3000π/30) × 0.465 Trated = Km Ia,rated = 3.78 N · m part (b): Tload = Km Ia − Trot . Here Trot = 87/(3000π/30) = 0.27 N·m. Thus Tload = 2.61 N·m and Pload = Tload ωm = 729 W. part (c): The differential equation governing the motor speed is πJ dn dωm = = Tmech − Trot − Tload J dt 30 dt WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 135 Here, n is the motor speed in r/min, Tmech = Km Ia = 0.465 × 7.0 = 3.26 N·m and, from part (b), n = 0.273 n N · m Tload = 729 2670 Thus, the differential equation is dn + 4.094 n − 1.252 × 104 = 0 dt and the solution is n = 3051 − 381e−t/τ r/min where τ = 0.255 sec. Problem 11.9 From the solution to Problem 11.8, Ia,rated = 8.12 A. Neglecting rotational losses, the motor speed can be calculated from the differential equation J dωm = Tmech = −KmIa,rated dt and thus ωm = ωm,0 − Km Ia,rated J t and thus the motor will reach zero speed at time t= Jωm,0 (1.86 × 10−3 ) × (3000π/30) = = 0.155 sec Km Ia,rated 0.465 × 8.12 Problem 11.10 part (a): Rated speed = 120f /poles = 1800 r/min. part (b): Prated Irated = √ = 138.0 A 3 Vrated part (c): In per unit, Va = 1.0 and P = 1000/1100 = 0.909. Thus, Ia = 0.909 and Eaf = Va − jXs Ia = 1.55 − 49.7◦ per unit Thus If = 1.55 × 85 = 131 A. part (d): The inverter frequency will equal f = 60(1300/1800) = 43.3 Hz and the motor power input will be P = 1000(1300/1800)2.5 = 443 W. If one scales the base voltage and base power with frequency then the base impedance WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 136 will scale with frequency. Hence, under this new operating condition, the perunit terminal voltage, generated voltage and synchronous reactance will be unchanged while the per-unit power will be P = 443/(1100 × 43.3/60) = 0.558 per unit. Thus P Xs δ = − sin−1 = −27.9circ Va Eaf and Êaf = 1.55 −27.9◦ Va − Êaf Iâ = = 0.688 26.8◦ jXs Thus the power factor is cos−1 (26.8◦ ) = 0.89 leading. part (e): Continuing with the base quantities of part (d), Ia = 0.558 per unit and Eaf = Va − jXs Ia = 1.20 − 47.0◦ per unit and thus If = 1.20 × 85 = 102 A. Problem 11.11 part (a): No numerical calculation required. part (b): 1500 r/min: Va = 3.83 kV, l − l Pmax = 833 kW If = 131 A 2000 r/min: Va = 4.60 kV, l-l Pmax = 1000 kW If = 126 A Problem 11.12 Ls = 5.23 mH Laf = 63.1 mH Trated = 531 N · m Problem 11.13 part (a): Laf = √ √ 2 Vbase = 63.1 mH 3 ωbase AFNL Ls can be calculated from the per-unit value of Xs . WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 137 Zbase = 2 Vbase = 2.12 Ω Pbase and Lbase = Zbase /ωbase = 5.6 mH. Thus, Xs = Ls = Xs = 1.97 Ω Zbase Xs = 5.23 mH Lbase part (b): ωm,base = ωbase (2/poles) = 60π and Tbase = Pbase /ωm,base = 531 N·m. Thus, T = 0.5 Tbase = 265 N·m. 2 2 T iQ = = 100 A 3 poles Laf If iQ Ia = √ = 70.8 A, rms 2 part (c): Eaf = ωbase Laf If √ = 235 V 2 Because iD = 0, Iâ and Êaf both lie along the quadrature axis. Thus, the terminal voltage magnitude will be given by Va = |Eaf + jXs Ia | = 274 V, l-n = 474 V, l-l Problem 11.14 part (a): The various machine parameters were calculated in the solution to Problem 11.13. T = 0.75Tbase = 398 N·m and ωm = 1475π/30 = 154.5 rad/sec. Thus, P = ωm T = 61.5 kW. part (b): 2 2 T = 145.1 A iQ = 3 poles Laf If iQ Ia = √ = 102.6 A, rms 2 part (c): fe = 60(1475/1800) = 49.2 Hz. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 138 part (d): ωbase Laf If √ = 200 V 2 Eaf = Because iD = 0, Iâ and Êaf both lie along the quadrature axis. Thus, the terminal voltage magnitude will be given by Va = |Eaf + jXs Ia | = 260 V, l-n = 450 V, l-l Problem 11.15 part (a): The various machine parameters were calculated in the solution to Problem 11.13. With Tref increased to 0.8Tbase = 424 N·m 2 2 Tref = 160.3 A iQ = 3 poles Laf If iQ Ia = √ = 113.3 A, rms 2 Eaf = ωbase Laf If √ = 235.3 V 2 Because iD = 0, Iâ and Êaf both lie along the quadrature axis. Thus, the terminal voltage magnitude will be given by Va = |Eaf + jXs Ia | = 324.5 V, l-n = 562.1 V, l-l = 1.22 per unit part (b): The required calculations follow those of Example 11.9. (i) The terminal voltage will be set equal to 460 V, l-l (1.0 per unit). (ii) The line-to-neutral terminal voltage is Va,l−n = 460/sqrt3 = 265.6 V. Thus Ia = (ωm Tref = 100.4 A, rms 3Va,l−n (iii) δ = tan −1 ωm Ls Ia Va,l−n = −26.7◦ Thus irmQ = √ 2 Ia sin δ = 113.8 A irmD = √ 2 Ia sin δ = −84.9 A and WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 139 (iv) 2 2 Tref If = = 19.7 A 3 poles Laf iQ Problem 11.16 T = 4431 N·m If = 121.7 A iD = -78.4 A iQ = 95.5 A Ia = 87.4 A, rms Va = 1993 V, rms, l-l Problem 11.17 part (a): ΛPM √ √ √ 2 Va,rated, l-n 2 230/ 3 = 0.512 Wb = = ωm,rated 3500π/30 part (b): The frequency will be 60 Hz and hence Xs = ωe Ls = 3.24 Ω. √ Eaf = (3600/3500)(230/ 3) = 136.6 V. Ia,rated = 2000/(sqrt3 230) = 5.02 A. The armature current is equal to Va,rated, l-n − Êaf Ia = jXs Although the magnitude of Êaf = Eaf δ is known, its angle δ (required to give Ia = Ia,rated ) is not. A MATLAB script can be used to easily iterate to find that δ = −6.73 ◦. The motor power is then given by 3Eaf Va,rated, l-n P =− sin δ = 1.96 kW Xs Then, T = P = 5.22 N · m ωm and 2 2 T = 6.80 A iQ = 3 poles ΛPM iD = 2 2Ia,rated + i2Q = 2.05 A WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 140 Problem 11.18 As calculated in the solution to Problem 11.17, ΛPM = 0.512 Wb. At 4000 r/min, fe = (4000/3600)60 = 66.7 Hz and thus ωe = 2πfe = 418.9 rad/sec. The rms line-to-neutral armature flux linkages under this operating condition will be √ 2 Va,rated, l-n = 0.448 Wb λa = ωe and maximum torque will correspond to operating the motor at its rated armature current Ia = Ia,rated = 5.02 A. Solving λa = λ2D + λ2Q 2 = (Ls + ΛPM )2 + (Ls iQ )2 2 = 2(Ls Ia )2 + 2Ls iD ΛPM + Λ2PM 2 for iD gives iD = 2λ2a − 2(Ls Ia )2 − Λ2PM = −4.38 A. 2Ls ΛPM Thus iQ = 2Ia2 − i2D = 5.62 A Thus, the maximimum torque will be given by 3 poles ΛPM iQ = 4.32 N · m Tmax = 2 2 and, for a speed of 4000 r/min (ωm = 418.9 rad/sec) Pmax = ωm Tmax = 1810 W Problem 11.19 The rated current of this motor is Prated = 37.7 A Ia,rated = √ 3 Va,rated, l-l ΛPM √ √ 2 Va,rated, l-n 2(230/sqrt3) = 0.235 Wb = = ωe 7620π/30 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 141 part (a): The torque will be maximized when iQ is maximized. In this case, this will occur when iD = 0 and thus √ iQ,max = 2 Ia,rated = 53.2 A and thus Tmax 3 poles = ΛPM iQ,max = 18.8 N · m 2 2 part (b): The peak line-to-neutral flux linkages are λa = Λ2PM + λ2Q = Λ2PM + (Ls iQ,max )2 = 0.257 Wb Thus, to avoid exceeding rated terminal voltage, the electrical frequency of the motor must be limited to √ 2 Va,rated, l-n = 731.9 rad/sec ωe,max = λa and the corresponding motor speed will be 30 n = ωe,max = 6989 r/min π part (c): At 10,000 r/min, ωe = 10000π/30 = 1047 rad/sec. In order to maintain rated terminal voltage, the peak line-to-neutral armature flux linkages must now be limited to √ 2 Va,rated, l-n = 0.179 Wb λa,max = ωe Thus, solving the peak line-to-neutral armature flux linkages λa,max = λ2D + λ2Q = (Ls + ΛPM )2 + (Ls iQ )2 = 2(Ls Ia,rated )2 + 2Ls iD ΛPM + Λ2PM 2 for iD gives iD = and thus λ2a,max − 2(Ls Ia,rated )2 − Λ2PM = −37.3 A. 2Ls ΛPM WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 142 iQ = 2 2Ia,rated − i2D = 38.0 A The motor torque is then given by 3 poles T = ΛPM iQ = 13.4 N · m 2 2 Since this is a two-pole machine and ωm = ωe , the corresponding power will be P = ωm T = 14.1 kW. The motor power factor will be P = 0.937 power factor = √ 3 Va,rated l-l Ia,rated Problem 11.20 Problem 11.21 part (a): Following the analysis of Chapter 6 Z1,eq = R1,eq + X1,eq = jXm (R1 + jX1 ) = 0.099 + j1.08Ω R1 + j(X1 + Xm WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 143 Tmax = smaxT = 2 0.5nphV1,eq = 234 N · m ωs (X1,eq + X2 ) R2 2 + (X1,eq + X2 )2 R1,eq = 0.102 = 10.2% part (b): ωs = 2πf (2/poles) = 60π = 188.5 rad/sec. At s = 0.029, ωm = (1 − s)ωs = 183.0 rad/sec. The torque is given by 2 (R2 /s) nph V1,eq 1 T = = 126 N · m ωs (R1,eq + (R2 /s))2 + (X1,eq + X2 )2 and the power is P = ωm T = 23.1 kW. part (c): With the frequency reduced from 60 Hz to 30 Hz, ωs , the terminal voltage and each reactance must be scaled by the factor (35/60). The torque expression can be solved for the slip. This can most easily be done iteratively with a MATLAB script. The result is s = 0.051 = 5.1%, the speed is 997 r/min and the output power is 13.1 kW. Problem 11.22 part (a): part (b): The same MATLAB script can be used to iteratively find the drive frequency for which smaxT = 1.0. The result is a drive frequency of 5.44 Hz and a torque of 151 N·m. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 144 Problem 11.23 Problem 11.24 The motor torque is a function of the ratio R2 /s. The slip with R2,ext = 0 is 1200 − 1157 = 0.0358 1200 s0 = and that with R2,ext = 0.87 Ω is 1200 − 1072 = 0.1067 1200 s1 = Thus, solving R2 R2 + 0.87 = s0 s1 for R2 gives R2 = 0.44 Ω. Problem 11.25 The motor torque is a function of the ratio R2 /s. The slip with R2,ext = 0 is 1200 − 1157 = 0.0358 1200 s0 = The desired operating speed corresponds to a slip of s1 = 1200 − 850 = 0.2917 1200 Thus substituting the value of R2 found in the solution to Problem 11.24 and solving for R2,ext R2 + R2,ext R2 = s0 s1 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 145 for R2,ext gives R2,ext = 3.14 Ω. Problem 11.26 part (a): If R1 is assumed negligible, the torque expression becomes 2 nph V1,eq (R2 /s) 1 T = ωs (R2 /s)2 + (X1,eq + X2 )2 Substituting the corresponding expressions for Tmax 2 1 0.5nphV1,eq Tmax = ωs X1,eq + X2 smaxT = R2 X1,eq + X2 gives T = Tmax s smaxT 2 + smaxT s Defining the ratio of full-load torque to maximum torque as k≡ 1 Tfl = 0.472 = Tmax 2.12 the full-load slip can then be found as k √ sfl = smaxT = 0.0414 = 4.14% 1 + 1 − k2 part (b): The full load rotor power dissipation is given by sfl = 3240 W Protor = Pfl 1 − sfl part (c): At rated load, ωm,rated = (1 − sfl )ωs == 180.7 rad/sec. The rated torque is Trated = Prated /ωm,rated = 415 N·m. Setting s = 1 gives 2 Tstart = Tmax = 68.1% = 283 N · m 1 + smaxT smaxT part (d): If the stator current is at its full load value, this means that R2 /s is equal to its full load value and hence the torque will be equal to the full-load torque, 415 N·m. WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 146 part (e): The slip will be twice the original full load slip or 8.26%. Problem 11.27 part (a): sfl = 1200 − 1169 = 0.0258 1200 and thus the full-load rotor power dissipation is equal to sfl = 928 W Protor = Pfl 1 − sfl part (b): Defining k≡ Tmax = 2.45 Tfl and using the derivation found in the solution to Problem 11.26 gives smaxT = sfl k + k 2 − 1 = 0.1211 Thus the motor speed at maximim torque is nmax = 1200(1−smaxT) = 1055 r/min. part (c): We want smaxT to increase by a factor of 1/0.1211 = 8.26. Thus the rotor resistance must increase by this factor. In other words R2 + R2,ext = 8.26R2 which gives R2,ext = 1.67 Ω. part (d): The 50-Hz voltage will be (5/6) that of 60-Hz. Thus the applied voltage will be 367 V, line-to-line. part (e): If the frequency and voltage are scaled from their rated value by a factor kf , the torque expression becomes 1 nph (kf V1,eq )2 (R2 /s) T = kf ωs0 (R2 /s)2 + (kf (X1,eq + X2 ))2 where ωs0 is the rated-frequency synchronous speed of the motor. Clearly, the torque expression will remain constant if the slip scales invesely with kf . Thus 60 sfl,50 = sfl,60 = 0.031 50 The synchronous speed at 50 Hz is 1000 r/min and thus nfl,50 = 1000(1 − sfl,50 ) = 969 r/min WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 147 Problem 11.28 part (a): From the data given in Problem 11.23, the motor inductances are: L1 = 3.13 mH; L2 = 3.50 mH; Lm = 128 mH; and thus LS = L1 + Lm = 131.5 mH and LR = L2 + Lm = 131.9 mH Ra = R1 = 108 mΩ and RaR = R2 = 296 mΩ. Finally, the rated motor torque The peak flux linkages corresponding to rated voltage line-to-neutral voltage are given by √ √ 2 Vbase 2 2400 √ √ = = 5.19 Wb λrated = 3 ωbase 3 (120π) The required torque can be determined from the given power and speed as Tmech = Pmech 400 × 103 = 3327 N · m = ωm 1148π/30 Setting λDR = λrated gives Tmech 2 2 LR iQ = = 146.1 A 3 poles Lm λDR and iD = λDR = 40.5 A Lm part (b): i2D + i2Q Ia = 2 = 107.2 A part (c): ωme = ωm ωe = ωme + and thus poles 2 RaR LR = 360.6 rad/sec iQ iD = 368.7 rad/sec WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 148 fe = ω2 = 58.7 Hz 2π part (d): Va = = (Ra iD − ωe (LS − L2m 2 LR )iQ ) + (Ra iQ + ωe LS iD )2 2 1421 V, l-n = 2461 V, l-l Problem 11.29 part (a): From the given data, the motor inductances are: L1 = 0.915 mH; L2 = 0.936 mH; Lm = 49.34 mH; and thus LS = L1 + Lm = 50.25 mH and LR = L2 + Lm = 50.27 mH Ra = R1 = 32.2 mΩ and RaR = R2 = 70.3 mΩ. Finally, the rated motor torque The peak flux linkages corresponding to rated voltage line-to-neutral voltage are given by √ √ 2 Vbase 2 230 = √ = 0.498 Wb λrated = √ 3 ωbase 3 (120π) The motor torque is Tmech = 85(1300/1800) = 61.4 N·m. Setting λDR = λrated , we can solve for iQ and iD 2 Tmech 2 LR = 41.9 A iQ = 3 poles Lm λDR and iD = λDR = 10.1 A Lm The motor mechanical velocity in electrical rad/sec is poles ωme = ωm = 272.3 rad/sec 2 and thus WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 149 ωe = ωme + RaR LR iQ iD = 278.1 rad/sec and fe = ω2 = 44.3 Hz 2π part (b): i2D + i2Q Ia = Va = 2 (Ra iD − ωe (LS − = 30.4 A L2m 2 LR )iQ ) + (Ra iQ + ωe LS iD )2 2 = 101.8 V, l-n = 176.3 V, l-l part (c): Sin = √ 3 Va Ia = 9.30 kVA part (d): Problem 11.30 The motor parameters are calculated in the solution to Problem 11.29. part (a): The motor torque is Tmech = 85(1450/1800) = 68.5 N·m. Setting λDR = λrated , we can solve for iQ and iD 2 2 LR Tmech iQ = = 46.7 A 3 poles Lm λDR iD = λDR = 10.1 A Lm WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 150 and i2D + i2Q Ia = = 33.8 A 2 part (b): The motor mechanical velocity in electrical rad/sec is poles ωme = ωm = 303.7 rad/sec 2 and thus ωe = ωme + RaR LR iQ iD = 310.1 rad/sec and fe = ω2 = 49.4 Hz 2π part (c): iQ is now increased to 51.4 A and hence, with IDR and hence λDR unchanged 3 poles Lm λDR iQ = 75.3 N · m Tmech = 2 2 LR Thus the motor speed is n = 1800 Tmech 85 = 1595 r/min and ωm = nπ/30 = 167.0 rad/sec. Pmech = Tmech ωm = 11.4 kW part (d): The terminal voltage is Va = = (Ra iD − ωe (LS − L2m 2 LR )iQ ) + (Ra iQ + ωe LS iD )2 2 125.6 V, l-n = 217.5 V, l-l The drive frequency can be found from poles ωme = ωm = 334.1 rad/sec 2 ωe = ωme + RaR LR iQ iD = 341.2 rad/sec WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 151 and fe = ω2 = 54.3 Hz 2π part (e): Sin = √ 3 Va Ia = 13.9 kVA part (f): Iteration with a MATLAB script gives λDR = 95.3% of λrated . Problem 11.31 part (a): From the given data, the motor inductances are: L1 = 4.96 mH; L2 = 6.02 mH; Lm = 118.3 mH; and thus LS = L1 + Lm = 123.3 mH and LR = L2 + Lm = 124.3 mH Ra = R1 = 212 mΩ and RaR = R2 = 348 mΩ. Finally, the rated motor torque The peak flux linkages corresponding to rated voltage line-to-neutral voltage are given by √ √ 2 Vbase 2 4160 = 9.01 Wb = √ λrated = √ 3 ωbase 3 (120π) At a power output of 1050 kW and a speed of 828 r/min, ωm = 84.3 rad/sec, Tmech = 1.25 × 104 N·m. Setting λDR = λrated gives 2 2 T iQ = = 242.1 A 3 poles ΛPM iD = Ia = 2 2Ia,rated + i2Q = 76.2 A i2D + i2Q 2 = 179.5 A The terminal voltage is Va = (Ra iD − ωe (LS − L2m 2 LR )iQ ) = 2415 V, l-n = 4183 V, l-l 2 + (Ra iQ + ωe LS iD )2 WWW.COMUNIDADEELETRICIDADE.BLOGSPOT.COM 152 The drive frequency can be found from poles ωme = ωm = 337.2 rad/sec 2 ωe = ωme + RaR LR iQ iD = 346.1 rad/sec and fe = ω2 = 55.1 Hz 2π part (b): The equivalent-circuit of Chapter 6 can be analyzed readily using MATLAB as follows: - All the reactances must be scaled from their 60-Hz values to 55.1 Hz. - The rms input voltage must be set equal to 2415 V, line-to-neutral. - The slip must be calculated based upon a synchronous speed of ns = 60fe (2/poles) = 826 r/min. If this is done, the equivalent circuit will give exactly the same results as those of part (a).

Exercicios resolvidos Maquinas Eletricas

Related documents

Products

Support

Exercicios resolvidos Maquinas Eletricas

Related documents

Add this document to collection(s)

Add this document to saved

Suggest us how to improve StudyLib