13:36 26/06/2023 Section 2.0 Terminology Section 2.0 Terminology Tổng điểm 100/100 TWI SEA - WIS5 & WIS7 Training Email * phuclocvt2023@gmail.com Candidate name * NGUYEN BAO TRUNG 1. Which of the following welds would usually be considered for an open corner joint? *10/10 Plug weld Butt weld Fillet weld None of the above https://docs.google.com/forms/d/e/1FAIpQLSci8zcnd3PONb4o-7gc0mWlnD9A2jcPrBOOstv-tTM6VJjzSw/viewscore?viewscore=AE0zAgCQd1ZkKAH… 1/5 13:36 26/06/2023 Section 2.0 Terminology 2. Which of the following fillet welds would be considered to have the highest fatigue strength (assuming all welding parameters are the same, same material and welded using the same WPS) *10/10 8mm throat thickness mitre fillet weld 7mm throat thickness fillet weld + 2mm excess weld metal Convex fillet weld with 10mm leg length Concave fillet weld with 8mm throat thickness 3. A fillet weld has an actual throat thickness of 8mm and a leg length of 7mm. What is the amount of excess weld metal? *10/10 2.1mm 1.8mm 3.1mm 1.4mm 4. What would be a typical bevel angle for a single V butt weld welded with a manual welding process in the PA position? *10/10 70 deg 30 - 35 deg 15 deg None of the above https://docs.google.com/forms/d/e/1FAIpQLSci8zcnd3PONb4o-7gc0mWlnD9A2jcPrBOOstv-tTM6VJjzSw/viewscore?viewscore=AE0zAgCQd1ZkKAH… 2/5 13:36 26/06/2023 Section 2.0 Terminology 5. Which of the following best describes a heterogeneous joint? * 10/10 A welded joint in which there are significant differences in mechanical properties between the weld metal and parent material. A welded joint in which there are significant differences in mechanical properties between parent materials A welded joint in which the weld metal and parent material have no significant differences in mechanical Both a and b 6. To keep distortion to a minimum, which of the following butt weld *10/10 preparations would be the most suited for a 15mm thick structural welded joint in the PA position Single U butt Double V butt Single V butt All of the above 7. Which of the following welding process can weld autogeneously? * 10/10 TIG OFW Friction Weld All of the above https://docs.google.com/forms/d/e/1FAIpQLSci8zcnd3PONb4o-7gc0mWlnD9A2jcPrBOOstv-tTM6VJjzSw/viewscore?viewscore=AE0zAgCQd1ZkKAH… 3/5 13:36 26/06/2023 Section 2.0 Terminology 8. Fusion line: * 10/10 Is another term for Weld Zone Is another term for Weld Junction Area between Parent Material and HAZ All of the above 9. How do we determine what the correct weld joint preparation should *10/10 be? By refering to the fabrication drawing The welder foremen will decide the suitable preparation Inspector will give the information By referring to Welding Procedure Specification 10. Which the following is true? * 10/10 Plug weld are in T joints Spot weld are in edge joints Fillet weld are in corner joints Edge weld are in lap joints Nội dung này không phải do Google tạo ra hay xác nhận. - Điều khoản Dịch vụ - Chính sách quyền riêng tư Biểu mẫu https://docs.google.com/forms/d/e/1FAIpQLSci8zcnd3PONb4o-7gc0mWlnD9A2jcPrBOOstv-tTM6VJjzSw/viewscore?viewscore=AE0zAgCQd1ZkKAH… 4/5 13:36 26/06/2023 Section 2.0 Terminology https://docs.google.com/forms/d/e/1FAIpQLSci8zcnd3PONb4o-7gc0mWlnD9A2jcPrBOOstv-tTM6VJjzSw/viewscore?viewscore=AE0zAgCQd1ZkKAH… 5/5
