WCDMA RAN, Rel. RU40,
Operating Documentation,
Issue 03
Radio Network Parameters in Flexi Direct
DN70456011
Issue 06
Approval Date 2013-09-20
Confidential
Radio Network Parameters in Flexi Direct
The information in this document is subject to change without notice and describes only the
product defined in the introduction of this documentation. This documentation is intended for the
use of Nokia Siemens Networks customers only for the purposes of the agreement under which
the document is submitted, and no part of it may be used, reproduced, modified or transmitted
in any form or means without the prior written permission of Nokia Siemens Networks. The
documentation has been prepared to be used by professional and properly trained personnel,
and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes
customer comments as part of the process of continuous development and improvement of the
documentation.
The information or statements given in this documentation concerning the suitability, capacity,
or performance of the mentioned hardware or software products are given "as is" and all liability
arising in connection with such hardware or software products shall be defined conclusively and
finally in a separate agreement between Nokia Siemens Networks and the customer. However,
Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions
contained in the document are adequate and free of material errors and omissions. Nokia
Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which
may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO
EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED
TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY
OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION
IN IT.
This documentation and the product it describes are considered protected by copyrights and
other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark
of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective
owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2013. All rights reserved
f
Important Notice on Product Safety
This product may present safety risks due to laser, electricity, heat, and other sources
of danger.
Only trained and qualified personnel may install, operate, maintain or otherwise handle
this product and only after having carefully read the safety information applicable to this
product.
The safety information is provided in the Safety Information section in the “Legal, Safety
and Environmental Information” part of this document or documentation set.
The same text in German:
f
Wichtiger Hinweis zur Produktsicherheit
Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder
andere Gefahrenquellen ausgehen.
Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch
geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen.
Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal,
Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentationssatzes.
2
Id:0900d80580931b1d
Confidential
DN70456011
Issue 06
Radio Network Parameters in Flexi Direct
Table of contents
This document has 3054 pages.
Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
DN70456011
1
1.1
1.2
1.3
Introduction to Radio Network Parameters in Flexi Direct . . . . . . . . . .
Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Descriptions of parameter groups . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to read parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
2.18
ADJD Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
ADJDChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 387
ADJDId (Identifier of additional intra-frequency adjacency). . . . . . . . . 388
AdjdCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
AdjdCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . 389
AdjdDERR (Disable Effect on Reporting Range). . . . . . . . . . . . . . . . . 390
AdjdHSDPAHopsId (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . . . 391
AdjdLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
AdjdMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
AdjdMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
AdjdMNCLength (Mobile Network Code Length). . . . . . . . . . . . . . . . . 395
AdjdNRTHopsId (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 396
AdjdRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
AdjdRNCId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
AdjdRTHopsId (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 399
AdjdRTWithHSDPAHopsId (HSDPA HOPS identifier for speech services)
400
AdjdSRBHopsId (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 401
AdjdScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . 402
AdjdTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
ADJG Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJGBlindHO (ADJG Blind Handover to GSM/GPRS) . . . . . . . . . . . .
ADJGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJGId (Inter-system adjacency identifier) . . . . . . . . . . . . . . . . . . . . .
ADJGType (Inter-system Neighbour Cell Type) . . . . . . . . . . . . . . . . .
AdjgBCC (Base Station Colour Code) . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgBCCH (BCCH ARFCN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgBandIndicator (Band Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgMNCLength (Mobile Network Code Length). . . . . . . . . . . . . . . . .
AdjgNCC (Network Colour Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . .
AdjgTxPwrMaxRACH (Maximum UE TX Power on RACH). . . . . . . . .
AdjgTxPwrMaxTCH (Maximum UE TX Power on TCH) . . . . . . . . . . .
NrtHopgIdentifier (NRT HOPG Identifier). . . . . . . . . . . . . . . . . . . . . . .
Id:0900d80580931b1d
Confidential
384
384
384
385
405
405
406
407
408
409
410
411
412
413
414
415
416
416
417
421
422
423
3
Radio Network Parameters in Flexi Direct
3.18
RtHopgIdentifier (RT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 424
4
4.1
4.2
4.3
4.4
4.5
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
ADJI Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
ADJIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
ADJIId (Inter-frequency adjacency identifier) . . . . . . . . . . . . . . . . . . . . 427
AdjiCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
AdjiCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . . 428
AdjiComLoadMeasDRNCCellNCHO (NCHO activity of common load measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
AdjiEcNoOffsetNCHO (CPICH EcNo offset for the non-critical HO procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
AdjiHandlingBlockedCellSLHO (Handling of blocked IF neighbour cell in
SLHO procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
AdjiLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434
AdjiMCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435
AdjiMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
AdjiMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . 437
AdjiNCHOHSPASupport (ADJI HSPA Cell for Non Critical Handover) 438
AdjiRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
AdjiRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
AdjiSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . . 441
AdjiScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . . 443
AdjiTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
AdjiTxPwrDPCH (Maximum UE TX Power on DPCH) . . . . . . . . . . . . . 445
AdjiTxPwrRACH (Maximum UE TX Power on RACH) . . . . . . . . . . . . . 447
AdjiUARFCN (UTRA Absolute Radio Frequency Channel Number) . . 448
BlindHOTargetCell (Blind HO target cell) . . . . . . . . . . . . . . . . . . . . . . . 450
NrtHopiIdentifier (NRT HOPI Identifier). . . . . . . . . . . . . . . . . . . . . . . . . 451
RtHopiIdentifier (RT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 452
5
5.1
5.2
5.3
5.4
5.5
ADJL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454
ADJLChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 454
ADJLId (Identifier of inter- system adjacency to LTE) . . . . . . . . . . . . . 455
AdjLEARFCN (E-UTRA Absolute Radio Frequency Channel Number) 456
AdjLMeasBw (Measurement Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . 457
HopLIdentifier (HOPL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
ADJS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
ADJSChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . . . 459
ADJSId (Intra-frequency adjacency identifier) . . . . . . . . . . . . . . . . . . . 460
AdjsCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
AdjsCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . . 461
AdjsDERR (Disable Effect on Reporting Range) . . . . . . . . . . . . . . . . . 462
AdjsEcNoOffset (CPICH Ec/No Offset). . . . . . . . . . . . . . . . . . . . . . . . . 463
AdjsLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
AdjsMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
AdjsMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466
AdjsMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 467
AdjsRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
4.6
4.7
4
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
6.12
6.13
6.14
6.15
6.16
6.17
6.18
6.19
6.20
6.21
AdjsRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
AdjsSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 470
AdjsScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . 472
AdjsTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
AdjsTxPwrRACH (Maximum UE TX Power on RACH) . . . . . . . . . . . . 474
HSDPAHopsIdentifier (HSDPA HOPS identifier). . . . . . . . . . . . . . . . . 475
NrtHopsIdentifier (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 476
RTWithHSDPAHopsIdentifier (HSDPA HOPS identifier for speechservices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
RtHopsIdentifier (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 479
SRBHopsIdentifier (SRB HOPS Identifier). . . . . . . . . . . . . . . . . . . . . . 479
7
7.1
7.2
7.3
7.4
7.5
7.6
CBCI Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CBCIChangeOrigin (CBCI Change Origin) . . . . . . . . . . . . . . . . . . . . .
CBCIId (CBCI Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CBCIPaddrType (Type of CBC IP address). . . . . . . . . . . . . . . . . . . . .
CBCIPaddress (IP address of the CBC) . . . . . . . . . . . . . . . . . . . . . . .
ETWSsupportEnabled (ETWS Support Enabled) . . . . . . . . . . . . . . . .
IUOIdentifier (IUO Object Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . .
481
481
482
483
483
484
485
8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
CMOB Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACBarredListSystem (Access Class Barred List given by System). . .
CMOBChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . .
CMOBId (Congestion Management Group Identifier) . . . . . . . . . . . . .
CellAccessRestriction (Cell Access Restriction) . . . . . . . . . . . . . . . . .
RestrictionGroupName (Restriction group name) . . . . . . . . . . . . . . . .
RestrictionGroupType (Restriction group type) . . . . . . . . . . . . . . . . . .
TrafficRestriction (Traffic Restriction). . . . . . . . . . . . . . . . . . . . . . . . . .
487
487
489
490
491
492
493
494
9
9.1
FMCG Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
AMRDirReCell (Usage of Directed Retry of AMR call Inter-system Handov)
495
BLHOFailIRCellPenalty (BLHO failure inter-system cell penalty) . . . . 496
DLDPCHTxPwrClOffset (DL DPCH Transmission Power Cancellation Offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
FMCGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 498
FMCGId (FMCG identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
GSMcauseCPICHEcNo (GSM HO caused by CPICH Ec/No). . . . . . . 500
GSMcauseCPICHrscp (GSM HO caused by CPICH RSCP). . . . . . . . 501
GSMcauseTxPwrDL (GSM HO caused by DL DPCH TX Power) . . . . 503
GSMcauseTxPwrUL (GSM HO caused by UE TX Power) . . . . . . . . . 504
GSMcauseUplinkQuality (GSM HO caused by UL DCH Quality) . . . . 506
GsmDLTxPwrThrAMR (DL DPCH TX Power Threshold for AMR) . . . 507
GsmDLTxPwrThrCS (DL DPCH TX Power Threshold for CS) . . . . . . 508
GsmDLTxPwrThrNrtPS (DL DPCH TX Power Threshold for NRT PS) 509
GsmDLTxPwrThrRtPS (DL DPCH TX Power Threshold for RT PS) . . 510
GsmMaxMeasPeriod (Maximum Measurement Period) . . . . . . . . . . . 511
GsmMeasAveWindow (Measurement Averaging Window) . . . . . . . . . 512
GsmMeasRepInterval (Measurement Reporting Interval) . . . . . . . . . . 513
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
9.11
9.12
9.13
9.14
9.15
9.16
9.17
DN70456011
Id:0900d80580931b1d
Confidential
5
Radio Network Parameters in Flexi Direct
9.18
9.19
9.20
9.21
9.22
9.23
9.24
9.25
9.26
9.27
9.28
9.29
9.30
9.31
9.32
9.33
10
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
10.9
10.10
10.11
10.12
10.13
10.14
10.15
10.16
10.17
10.18
10.19
10.20
10.21
10.22
10.23
10.24
6
GsmMinHoInterval (Minimum Interval Between HOs) . . . . . . . . . . . . . 514
GsmMinMeasInterval (Minimum Measurement Interval) . . . . . . . . . . . 515
GsmMinSLHOInterval (Minimum interval between repetitive inter-RAT
SLHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
GsmNcellSearchPeriod (GSM Neighbour Cell Search Period) . . . . . . 517
GsmUETxPwrFilterCoeff (UE TX Power Filter Coefficient) . . . . . . . . . 518
GsmUETxPwrThrAMR (UE TX Power Threshold for AMR) . . . . . . . . . 519
GsmUETxPwrThrCS (UE TX Power Threshold for CS) . . . . . . . . . . . . 520
GsmUETxPwrThrNrtPS (UE TX Power Threshold for NRT PS). . . . . . 521
GsmUETxPwrThrRtPS (UE TX Power Threshold for RT PS) . . . . . . . 522
GsmUETxPwrTimeHyst (UE TX Power Time Hysteresis) . . . . . . . . . . 523
IMSIbasedGsmHo (IMSI Based GSM HO) . . . . . . . . . . . . . . . . . . . . . . 525
ISHOClcauseCPICHEcNo (ISHO Cancellation caused by CPICH Ec/No) .
526
ISHOClcauseCPICHrscp (ISHO Cancellation caused by CPICH RSCP). .
527
ISHOClcauseTxPwrDL (ISHO Cancellation caused by DL DPCH TX Power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528
ISHOClcauseTxPwrUL (ISHO Cancellation caused by UE TX Power) 529
MaxBSICIdentTime (Maximum BSIC Identification Time) . . . . . . . . . . 530
FMCI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
FMCIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
FMCIId (FMCI identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533
IFHOcauseCPICHEcNo (IFHO caused by CPICH Ec/No) . . . . . . . . . . 534
IFHOcauseCPICHrscp (IFHO caused by CPICH RSCP) . . . . . . . . . . . 535
IFHOcauseTxPwrDL (IFHO caused by DL DPCH TX Power) . . . . . . . 537
IFHOcauseTxPwrUL (IFHO caused by UE TX Power). . . . . . . . . . . . . 539
IFHOcauseUplinkQuality (IFHO caused by UL DCH Quality). . . . . . . . 541
IMSIbasedIFHO (IMSI Based IFHO). . . . . . . . . . . . . . . . . . . . . . . . . . . 542
InterFreqDLTxPwrThrAMR (DL DPCH TX Power Threshold for AMR) 543
InterFreqDLTxPwrThrCS (DL DPCH TX Power Threshold for CS) . . . 544
InterFreqDLTxPwrThrNrtPS (DL DPCH TX Power Threshold for NRT PS)
545
InterFreqDLTxPwrThrRtPS (DL DPCH TX Power Threshold for RT PS) . .
546
InterFreqMaxMeasPeriod (Maximum Measurement Period) . . . . . . . . 547
InterFreqMeasAveWindow (Measurement Averaging Window) . . . . . . 548
InterFreqMeasRepInterval (Measurement Reporting Interval) . . . . . . . 549
InterFreqMinHoInterval (Minimum Interval Between HOs) . . . . . . . . . . 550
InterFreqMinMeasInterval (Minimum Measurement Interval) . . . . . . . . 550
InterFreqMinSLHOInterval (Minimum interval between repetitive IF
SLHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
InterFreqNcellSearchPeriod (Neighbour Cell Search Period). . . . . . . . 552
InterFreqUETxPwrFilterCoeff (UE TX Power Filter Coefficient) . . . . . . 553
InterFreqUETxPwrThrAMR (UE TX Power Threshold for AMR) . . . . . 555
InterFreqUETxPwrThrCS (UE TX Power Threshold for CS) . . . . . . . . 556
InterFreqUETxPwrThrNrtPS (UE TX Power Threshold for NRT PS) . . 557
InterFreqUETxPwrThrRtPS (UE TX Power Threshold for RT PS) . . . . 558
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
DN70456011
10.25
10.26
10.27
InterFreqUETxPwrTimeHyst (UE TX Power Time Hysteresis) . . . . . . 559
MBLBMobilityOffset (MBLB due to Mobility EcNo Offset) . . . . . . . . . . 560
MBLBMobilityRABComb (MBLB due to Mobility RAB Combinations) . 562
11
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
11.10
11.11
11.12
11.13
11.14
11.15
11.16
11.17
11.18
11.19
11.20
11.21
11.22
11.23
11.24
11.25
11.26
11.27
FMCS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ActiveSetWeightingCoefficient (Active Set Weighting Coefficient) . . .
AdditionReportingInterval (Addition Reporting Interval). . . . . . . . . . . .
AdditionTime (Addition Time). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdditionWindow (Addition Window) . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSRepBasedSHO (Detected Set Reporting Based SHO). . . . . . . . . .
DropReportingInterval (Drop Reporting Interval) . . . . . . . . . . . . . . . . .
DropTime (Drop Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DropWindow (Drop Window) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EDCHAddEcNoOffset (Allow E-DCH usage EcNo offset) . . . . . . . . . .
EDCHRemEcNoOffset (CPICH EcNo offset E-DCH usage removal) .
EcNoFilterCoefficient (CPICH Ec/No Filter Coefficient). . . . . . . . . . . .
FMCSChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . .
FMCSId (FMCS identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HHoEcNoCancel (CPICH Ec/No HHO Cancellation). . . . . . . . . . . . . .
HHoEcNoCancelTime (CPICH Ec/No HHO Cancellation Time) . . . . .
HHoEcNoThreshold (CPICH Ec/No HHO Threshold) . . . . . . . . . . . . .
HHoEcNoTimeHysteresis (CPICH Ec/No HHO Time Hysteresis) . . . .
HHoRscpCancel (CPICH RSCP HHO Cancellation) . . . . . . . . . . . . . .
HHoRscpCancelTime (CPICH RSCP HHO Cancellation Time) . . . . .
HHoRscpFilterCoefficient (CPICH RSCP HHO Filter Coefficient) . . . .
HHoRscpThreshold (CPICH RSCP HHO Threshold) . . . . . . . . . . . . .
HHoRscpTimeHysteresis (CPICH RSCP HHO Time Hysteresis) . . . .
IMSIbasedSHO (IMSI Based SHO) . . . . . . . . . . . . . . . . . . . . . . . . . . .
MaxActiveSetSize (Maximum Active Set Size) . . . . . . . . . . . . . . . . . .
ReplacementReportingInterval (Replacement Reporting Interval) . . .
ReplacementTime (Replacement Time) . . . . . . . . . . . . . . . . . . . . . . .
ReplacementWindow (Replacement Window). . . . . . . . . . . . . . . . . . .
563
563
564
565
567
568
570
571
573
574
575
576
578
579
580
581
584
585
587
589
592
593
594
596
597
599
600
602
12
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
12.9
12.10
12.11
12.12
12.13
HOPG Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AdjgHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . .
AdjgHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . .
AdjgMinRxLevNCHO (Minimum RX level for non-critical HO). . . . . . .
AdjgPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . .
AdjgPenaltyTimeNCHO (Penalty time for GSM cell in non-critical HO)
AdjgPriorityCoverage (Ncell Priority for Coverage HO) . . . . . . . . . . . .
AdjgPrioritySLHO (Neighbour cell priority for SLHO). . . . . . . . . . . . . .
AdjgQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . .
AdjgQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . .
AdjgRxLevMinHO (Minimum RX Level for Coverage HO). . . . . . . . . .
AdjgTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . .
HOPGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . .
HOPGId (HOPG Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
604
604
605
606
607
607
608
609
610
611
612
613
615
616
13
HOPI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 618
Id:0900d80580931b1d
Confidential
7
Radio Network Parameters in Flexi Direct
13.1
13.2
13.3
13.4
13.5
13.6
13.7
13.8
13.9
13.15
13.16
13.17
13.18
13.19
13.20
13.21
13.22
13.23
13.24
13.25
AdjiEcNoMargin (CPICH Ec/No Margin for IFHO) . . . . . . . . . . . . . . . . 618
AdjiHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . . 619
AdjiHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . . 620
AdjiMinEcNo (Minimum CPICH Ec/No for IFHO) . . . . . . . . . . . . . . . . . 621
AdjiMinEcNoNCHO (Minimum CPICH Ec/No for non-critical IFHO). . . 622
AdjiMinRSCP (Minimum CPICH RSCP for IFHO) . . . . . . . . . . . . . . . . 623
AdjiMinRscpNCHO (Minimum CPICH RSCP for non-critical IFHO) . . . 623
AdjiPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . . 624
AdjiPenaltyTimeNCHO (Penalty time for WCDMA cell in non-critical HO) .
625
AdjiPlossMargin (Pathloss Margin for IFHO) . . . . . . . . . . . . . . . . . . . . 626
AdjiPriorityCoverage (Ncell Priority for Coverage IFHO) . . . . . . . . . . . 627
AdjiPriorityDCellCAHO (Neighbour cell priority for DC HSDPA Capa Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 628
AdjiPriorityHSCAHO (Neighbour Cell Priority for HSPA Capability Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630
AdjiPriorityMIMOCAHO (Neighbour cell priority for MIMO Capa Based HO)
631
AdjiPriorityQuality (Ncell Priority for Quality IFHO) . . . . . . . . . . . . . . . . 632
AdjiPrioritySLHO (Neighbour cell priority for service and load IFHO) . . 633
AdjiQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . . 634
AdjiQoffset2 (Cell Re-selection Quality Offset 2) . . . . . . . . . . . . . . . . . 635
AdjiQqualMin (Cell Re-selection Minimum Quality) . . . . . . . . . . . . . . . 636
AdjiQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . . 637
AdjiTempOffset1 (Cell Re-selection Temporary Offset 1). . . . . . . . . . . 638
AdjiTempOffset2 (Cell Re-selection Temporary Offset 2). . . . . . . . . . . 639
BlindHORSCPThr (Blind HO RSCP threshold). . . . . . . . . . . . . . . . . . . 640
HOPIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 641
HOPIId (HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642
14
14.1
14.2
14.3
14.4
14.5
14.6
HOPL Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644
AdjLAbsPrioCellReselec (Cell Reselection Absolute Priority) . . . . . . . 644
AdjLQrxlevminEUTRA (Cell Reselection Minimum RX level) . . . . . . . . 645
AdjLThreshigh (Cell Reselection Threshold high). . . . . . . . . . . . . . . . . 645
AdjLThreslow (Cell Reselection Threshold low) . . . . . . . . . . . . . . . . . . 646
HOPLChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 647
HOPLId (HOPL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 648
15
15.1
15.2
15.3
15.4
15.5
15.6
15.7
15.8
15.9
15.10
HOPS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650
AdjsHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . . 650
AdjsHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . 651
AdjsPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . 652
AdjsQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . . 653
AdjsQoffset2 (Cell Re-selection Quality Offset 2) . . . . . . . . . . . . . . . . . 654
AdjsQqualMin (Cell Re-selection Minimum Quality) . . . . . . . . . . . . . . . 655
AdjsQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . . 655
AdjsTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . . 656
AdjsTempOffset2 (Cell Re-selection Temporary Offset 2) . . . . . . . . . . 658
EcNoAveragingWindow (CPICH Ec/No Averaging Window) . . . . . . . . 659
13.10
13.11
13.12
13.13
13.14
8
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
15.11
15.12
15.13
15.14
15.15
15.16
15.17
15.18
15.19
15.20
16
16.1
16.2
16.3
16.4
16.5
16.6
16.7
16.8
16.9
16.10
16.11
16.12
16.13
16.14
16.15
16.16
16.17
16.17.1
16.17.2
16.17.3
16.18
16.19
16.20
16.21
16.22
16.23
16.24
16.25
16.26
16.27
DN70456011
EnableInterRNCsho (Enable Inter-RNC Soft Handover) . . . . . . . . . . . 660
EnableRRCRelease (Enable RRC Connection Release) . . . . . . . . . . 661
HHOMarginAverageEcNo (HHO Margin for Average Ec/No) . . . . . . . 662
HHOMarginPeakEcNo (HHO Margin for Peak Ec/No) . . . . . . . . . . . . 663
HOPSChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . . 664
HOPSId (HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665
HSDPAAvailabilityIur (HSDPA availability of the neighbouring DRNC cell)
666
HSUPAAvailabilityIur (HSUPA availability of the neighbouring DRNC cell)
667
ReleaseMarginAverageEcNo (Release Margin for Average Ec/No) . . 668
ReleaseMarginPeakEcNo (Release Margin for Peak Ec/No) . . . . . . . 669
IADA Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 671
AlarmSetforWCELBLINIT (Alarm Set for WCEL BL-INIT) . . . . . . . . . . 671
CBCSourceIPAddress (Source IP address for IuBC interface) . . . . . . 672
CSAttachDetachAllowed (Attach-detach allowed) . . . . . . . . . . . . . . . . 672
CommonMCC (Common MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674
CommonMNC (Common MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675
CommonMNCLength (Common MNC Length) . . . . . . . . . . . . . . . . . . 676
ConnectionRetryCounter (OAM Connection Establishment Retry Counter)
677
DSCPStatisticsGroupA (DSCP statistics group A ) . . . . . . . . . . . . . . . 678
DSCPStatisticsGroupB (DSCP statistics group B) . . . . . . . . . . . . . . . 679
DSCPStatisticsGroupC (DSCP statistics group C) . . . . . . . . . . . . . . . 680
DSCPStatisticsGroupTCPack (DSCP code for DL TCP Ack statistics) 682
EmergencyCallRedirectTimer (Emergency Call Redirect Timer). . . . . 683
ExtendedULDLactivationTmr (Extended Cell_FACH inactivity supervision
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
IASCCRepTimer (Inter-Adapter SCC repetition timer) . . . . . . . . . . . . 685
LCSSupportForAnchoring (LCS Support for Anchoring) . . . . . . . . . . . 685
LCSfunctionality (LCS functionality). . . . . . . . . . . . . . . . . . . . . . . . . . . 687
MACLogicalChPriority (MAC logical channel priority definition) . . . . . 687
MACLogChPriSRB1 (MAC logical channel priority for SRB1) . . . . . . . 689
MACLogChPriSRB2 (MAC logical channel priority for SRB2) . . . . . . . 689
MACLogChPriSRB3 (MAC logical channel priority for SRB3) . . . . . . . 690
N302 (N302) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
N304 (N304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 692
N308 (N308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693
OMSBackupIpAddress (OMS Backup IP Address) . . . . . . . . . . . . . . . 694
OMSIpAddress (OMS IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
PWSMDuration (Duration of low traffic for cell shutdown) . . . . . . . . . . 695
PWSMExceededTrafficDur (Time limit for traffic to activate a shutdown
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696
PageRep1stInterv (Repetition interval of the first repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697
PageRep2ndInterv (Repetition interval of the second repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 699
RANAPprocInitWait (RANAP initiation timer). . . . . . . . . . . . . . . . . . . . 700
Id:0900d80580931b1d
Confidential
9
Radio Network Parameters in Flexi Direct
16.28
16.29
16.30
16.31
16.32
16.33
16.34
16.35
16.36
16.37
16.38
16.39
16.40
16.41
16.42
16.43
16.44
16.45
16.46
16.47
16.48
16.49
16.50
16.51
16.52
16.53
16.54
16.55
16.56
16.57
16.58
16.59
16.60
16.61
16.62
16.63
16.64
16.65
10
RNCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 701
RNCIPAddress (RNC IP-address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703
RNCName (RNC name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703
RTservicesForPS (PS domain RT service). . . . . . . . . . . . . . . . . . . . . . 704
RestrictionInterval (Restriction Interval) . . . . . . . . . . . . . . . . . . . . . . . . 705
RncClientTLSMode (RNC Client TLS Mode) . . . . . . . . . . . . . . . . . . . . 707
RncId (RNC Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 708
SIB11_priority (Priority for SIB11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709
SIB15_priority (Priority for SIB15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
SIB18_priority (Priority for SIB18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711
SIB19Priority (Priority for SIB19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711
SIB1_priority (Priority for SIB1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712
SIB2_priority (Priority for SIB2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 713
SIB3_priority (Priority for SIB3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 714
SIB5_priority (Priority for SIB5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715
SecOMSIpAddress (Secondary OMS IP address) . . . . . . . . . . . . . . . . 716
ServingOMS (Serving OMS ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717
ServingOMSAdminSetting (Serving OMS Admin Setting) . . . . . . . . . . 718
ServingOMSSwoRequest (Serving OMS Switchover Request) . . . . . . 720
T302 (T302) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721
T304 (T304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 722
T305 (T305) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
T307 (T307) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724
T308 (T308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725
T309 (T309) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 726
T314 (T314) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727
T316 (T316) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 729
T317 (T317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 730
ToAWE_NRT_DCH_tti10 (Time of Arrival Window Endpoint for NRT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 731
ToAWE_NRT_DCH_tti20 (Time of Arrival Window Endpoint for NRT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 732
ToAWE_NRT_DCH_tti40 (Time of Arrival Window Endpoint for NRT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733
ToAWE_RT_DCH_tti10 (Time of Arrival Window Endpoint for RT DCH (TTI
10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 734
ToAWE_RT_DCH_tti20 (Time of Arrival Window Endpoint for RT DCH (TTI
20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 735
ToAWE_RT_DCH_tti40 (Time of Arrival Window Endpoint for RT DCH (TTI
40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 736
ToAWE_Speech (Time of Arrival Window Endpoint for speech services) .
737
ToAWS_NRT_DCH_tti10 (Time of Arrival Window Startpoint for NRT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
ToAWS_NRT_DCH_tti20 (Time of Arrival Window Startpoint for NRT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
ToAWS_NRT_DCH_tti40 (Time of Arrival Window Startpoint for NRT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 740
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
16.66
16.70
16.71
16.72
16.73
16.74
16.75
ToAWS_RT_DCH_tti10 (Time of Arrival Window Startpoint for RT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 741
ToAWS_RT_DCH_tti20 (Time of Arrival Window Startpoint for RT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 742
ToAWS_RT_DCH_tti40 (Time of Arrival Window Startpoint for RT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743
ToAWS_Speech (Time of Arrival Window Startpoint for speech services)
744
TraceLCSHorizAccur (Trace LCS Horizontal Accuracy) . . . . . . . . . . . 745
TraceLCSPriority (Trace LCS Priority). . . . . . . . . . . . . . . . . . . . . . . . . 746
TraceLCSVertAccur (Trace LCS Vertical Accuracy) . . . . . . . . . . . . . . 747
TraceLCSWaitPeriod (Trace LCS Wait Period) . . . . . . . . . . . . . . . . . . 748
UL_DLcapacityReqWait (Waiting time for UL/DL capacity request) . . 749
WCELIdleAlarmTimeout (WCEL Idle Alarm Timeout) . . . . . . . . . . . . . 751
17
17.1
17.2
17.3
17.4
IPNB Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IPNBId (IPNB object identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NodeBIPAddress (Control Plane Destination Address Iub) . . . . . . . . .
SourceNBAPIPAddress (Iub control plane source IP address) . . . . . .
SourceNBAPIPNetmask (Iub control plane source IP netmask) . . . . .
18
18.1
18.2
18.3
18.4
18.5
18.6
18.7
18.8
IPQM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 757
BackgroundTCToDSCP (Background TC to DSCP mapping). . . . . . . 757
ConversationalTCToDSCP (Conversational TC to DSCP mapping) . . 758
IPQMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 759
IPQMId (IP Qos Management Identifier) . . . . . . . . . . . . . . . . . . . . . . . 760
InteractiveTHP1TCToDSCP (Interactive THP1 TC to DSCP mapping) 761
InteractiveTHP2TCToDSCP (Interactive THP2 TC to DSCP mapping) 762
InteractiveTHP3TCToDSCP (Interactive THP3 TC to DSCP mapping) 763
StreamingTCToDSCP (Streaming TC to DSCP mapping) . . . . . . . . . 764
19
19.1
19.2
19.3
19.3.1
19.3.2
19.4
19.5
19.6
19.7
19.8
19.9
19.10
19.11
19.12
19.13
19.14
19.15
IUCS Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 765
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . . 765
CNId (Core Network Identity). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 766
CSCNNRI (NRI for CS Core routing) . . . . . . . . . . . . . . . . . . . . . . . . . . 767
NRIMaxForCSCN (Maximum value of NRI range for CS Core routing) 768
NRIMinForCSCN (Minimum value of NRI range for CS Core routing) 769
CSFlexiIuWeight (CS Flexible Iu Weight) . . . . . . . . . . . . . . . . . . . . . . 770
DefaultCN (Default Core Network). . . . . . . . . . . . . . . . . . . . . . . . . . . . 771
IUCSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 772
IUCSId (IuCS Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773
IUOIdentifier (IUO Object Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . 774
IuState (State of Iu interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775
MinUDPPortCS (Minimum UDP Port) . . . . . . . . . . . . . . . . . . . . . . . . . 776
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777
PagingOptSupport (Support of Paging Optimization Feature). . . . . . . 778
RelocationSupport (Serving RNC Relocation Support) . . . . . . . . . . . . 779
RtcpActivation (RTCP activation). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 780
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . 781
16.67
16.68
16.69
DN70456011
Id:0900d80580931b1d
Confidential
752
752
752
753
755
11
Radio Network Parameters in Flexi Direct
19.16
19.17
19.18
19.19
TRafC (TRafC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 782
TRatC (TRatC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 783
TigOR (TigOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784
TinTR (TinTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 785
20
20.1
20.2
20.3
20.4
20.5
20.6
IUCSIP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 786
DestIPAddressCS (IP address for the IUCS destination subnet) . . . . . 786
IPBasedRouteIdCS (IP Based Route Identifier for IUCS). . . . . . . . . . . 787
IPNetmaskCS (IP netmask for the IUCS destination subnet) . . . . . . . . 788
IPQMIdCS (IPQM object id for IuCS) . . . . . . . . . . . . . . . . . . . . . . . . . . 790
IUCSIPChangeOrigin (IUCSIP Change Origin) . . . . . . . . . . . . . . . . . . 791
IUCSIPId (IUCSIP Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 792
21
21.1
21.2
21.3
21.4
21.5
21.6
21.7
21.8
21.9
21.10
21.11
21.12
21.13
21.14
21.15
21.16
21.16.1
21.16.2
21.16.3
21.17
21.18
21.19
21.19.1
21.19.2
21.19.3
IUO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794
CSCNDRXLength (CN CS domain specific DRX cycle length) . . . . . . 794
CS_T3212 (T3212) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 795
IUOChangeOrigin (IUO Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . 796
IUOId (IUO Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 797
IuBarringDelayTimerCS (Iu Barring Delay Timer for CS) . . . . . . . . . . . 798
IuBarringDelayTimerPS (Iu Barring Delay Timer for PS) . . . . . . . . . . . 799
IuBarringRecoveryGroupCS (Iu Barring Recovery Group for CS) . . . . 800
IuBarringRecoveryGroupPS (Iu Barring Recovery Group for PS) . . . . 801
IuBarringRecoveryTimerCS (Iu service barring recovery timer for CS) 802
IuBarringRecoveryTimerPS (Iu service barring recovery timer for PS) 803
NRILengthForCSCN (NRI length for CS Core Networks) . . . . . . . . . . . 804
NRILengthForPSCN (NRI length for PS Core Networks) . . . . . . . . . . . 805
NullNRIForCSPool (Null NRI value for CS Pool) . . . . . . . . . . . . . . . . . 806
NullNRIForPSPool (Null NRI value for PS Pool). . . . . . . . . . . . . . . . . . 807
OperatorWeight (Operator Weight). . . . . . . . . . . . . . . . . . . . . . . . . . . . 808
PLMNid (PLMN identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 809
MCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 810
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 811
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . . 812
PSCNDRXLength (CN PS domain specific DRX cycle length). . . . . . . 813
PS_NMO (Network Mode of Operation) . . . . . . . . . . . . . . . . . . . . . . . . 815
SharedAreaPLMNid (Shared area PLMN identity) . . . . . . . . . . . . . . . . 816
SharedAreaMCC (Shared area Mobile Country Code). . . . . . . . . . . . . 817
SharedAreaMNC (Shared area Mobile Network Code) . . . . . . . . . . . . 818
SharedAreaMNClength (Shared area Mobile Network Code Length) . 819
22
22.1
22.2
22.3
IUPS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 821
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . . 821
CNId (Core Network Identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 822
CellFACHRelocSupport (Cell_FACH state Serving RNC Relocation Support ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 823
DefaultCN (Default Core Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 823
IUOIdentifier (IUO Object Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 825
IUPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 825
IUPSId (IuPS Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 827
22.4
22.5
22.6
22.7
12
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
22.8
22.9
22.10
22.10.1
22.10.2
22.11
22.12
22.13
22.14
22.15
22.16
22.17
22.18
22.19
IuState (State of Iu interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PSCNNRI (NRI for PS Core routing) . . . . . . . . . . . . . . . . . . . . . . . . . .
NRIMaxForPSCN (Maximum value of NRI range for PS Core routing)
NRIMinForPSCN (Minimum value of NRI range for PS Core routing).
PSFlexiIuWeight (PS Flexible Iu Weight). . . . . . . . . . . . . . . . . . . . . . .
PagingOptSupport (Support of Paging Optimization Feature). . . . . . .
RelocationSupport (Serving RNC Relocation Support) . . . . . . . . . . . .
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . .
TDataFwd (T DATAfwd). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRafC (TRafC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRatC (TRatC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TigOR (TigOR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TinTR (TinTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
827
829
830
831
832
833
835
836
836
838
838
839
840
841
23
23.1
23.2
23.3
23.4
23.5
23.6
IUPSIP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DestIPAddressPS (IP address for the IUPS destination subnet). . . . .
IPBasedRouteIdPS (IP Based Route Identifier for IUPS) . . . . . . . . . .
IPNetmaskPS (IP netmask for the IUPS destination subnet) . . . . . . .
IPQMIdPS (IPQM object id for IuPS) . . . . . . . . . . . . . . . . . . . . . . . . . .
IUPSIPChangeOrigin (IUPSIP Change Origin) . . . . . . . . . . . . . . . . . .
IUPSIPId (IUPSIP Identifier ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
843
843
845
846
848
849
850
24
24.1
24.2
24.3
IUR Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 852
ADAURAId (FD-RNC neighboring Adapter shared URA identity) . . . . 852
AppAwareRANEnabled (Application Aware RAN Enabled). . . . . . . . . 853
CellFACHnRncRelocSupport (Cell_FACH state Serving RNC Relocation
Support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 854
DSCPHighIur (DSCP high priority for Iur) . . . . . . . . . . . . . . . . . . . . . . 855
DSCPLowIur (Low priority DSCP for Iur) . . . . . . . . . . . . . . . . . . . . . . . 856
DSCPMedDCHIur (DSCP medium priority on R99 DCH for Iur) . . . . . 857
DelayThresholdMaxIur (Maximum Threshold for HSUPA congestion handling delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 858
DelayThresholdMidIur (Middle Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 859
DelayThresholdMinIur (Minimum Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 860
HSDPACCEnabledIur (HSDPA Congestion Control activation Iur) . . . 861
HSDPAULCToDSCPIur (HSDPA UL FP Control traffic to DSCP mapping
Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 862
HSPAOverIur (HSPA over Iur). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 863
HSUPADLCToDSCPIur (HSUPA DL FP Control traffic to DSCP mapping
Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
IBTSSharing (IBTS Sharing). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
IPBasedRouteIdIur (IP based route identifier) . . . . . . . . . . . . . . . . . . . 866
IURChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . . . . 867
IURId (Iur Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 868
InterfaceMode (Configure the IUR in a special mode). . . . . . . . . . . . . 869
IurUPSupport (User Plane support of Iur connection) . . . . . . . . . . . . . 870
24.4
24.5
24.6
24.7
24.8
24.9
24.10
24.11
24.12
24.13
24.14
24.15
24.16
24.17
24.18
24.19
DN70456011
Id:0900d80580931b1d
Confidential
13
Radio Network Parameters in Flexi Direct
24.20
24.21
24.22
24.23
24.24
24.25
24.26
24.27
24.28
24.28.1
24.28.2
24.28.3
24.29
24.30
24.31
24.32
24.33
24.34
24.35
24.36
25
25.1
25.2
25.3
25.4
25.5
25.6
25.7
25.8
25.9
25.9.1
25.10
25.10.1
25.11
25.11.1
25.12
25.12.1
25.13
14
MaxFPDLFrameSizeIur (Maximum FP downlink frame size Iur) . . . . . 871
MaxIurNRTHSDSCHBitRate (Maximum NRT HS-DSCH MAC-d flow bit
rate over Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872
MinUDPPortIur (Minimum UDP port value) . . . . . . . . . . . . . . . . . . . . . 874
NRncId (Neighbour RNC identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . 874
NRncNetworkInd (Network indicator of neighbour RNC) . . . . . . . . . . . 876
NRncRelocationSupport (Serving RNC Relocation Support of neighbour
RNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 877
NRncSignPointCode (Signalling point code of neighbour RNC). . . . . . 878
NRncVersion (Release version of Neighbouring RNC) . . . . . . . . . . . . 879
NeighbouringPLMNid (Neighbouring PLMN identity) . . . . . . . . . . . . . . 880
MCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 882
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . . 883
NeighbouringRNWElement (Type of the Neighbouring RNW Element) 884
OverbookingSwitchIur (Overbooking Switch Iur) . . . . . . . . . . . . . . . . . 885
ProbabilityFactorMaxIur (ProbabilityFactor for Congestion Indication sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886
RNSAPCongAndPreemption (RNSAP Congestion And Preemption) . 887
ToAWEOffsetNRTDCHIP (ToAWE Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888
ToAWEOffsetRTDCHIP (ToAWE Offset for RT DCH connections over IP)
889
ToAWSOffsetNRTDCHIP (ToAWS Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 890
ToAWSOffsetRTDCHIP (ToAWS Offset for RT DCH connections over IP)
891
PFL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 893
AMRToNonPreferredLayer (AMR to Non Preferred Layer) . . . . . . . . . 893
BlindHORSCPThrAbove (Blind HO RSCP threshold above) . . . . . . . . 894
BlindHORSCPThrBelow (Blind HO RSCP threshold below) . . . . . . . . 894
LaySelLowLoadPref (Layer Selection Low Load Preferred) . . . . . . . . . 895
LaySelWeightBand (Layer Selection Weight of Band) . . . . . . . . . . . . . 896
LaySelWeightLoad (Layer Selection Weight of Load) . . . . . . . . . . . . . 897
LaySelWeightPrefLayer (Layer Selection Weight of Preferred Layer) . 898
LaySelWeightRSCP (Layer Selection Weight of RSCP) . . . . . . . . . . . 899
PFL64QAMAMR (Preferred Frequency Layer for 64QAM AMR) . . . . . 900
PrefLayer64QAMAMR (Preferred Layer for 64QAM AMR) . . . . . . . . . 901
PFL64QAMAMRNRT (Preferred Frequency Layer for 64QAM AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902
PrefLayer64QAMAMRNRT (Preferred Layer for 64QAM AMR and NRT) .
902
PFL64QAMNRT (Preferred Frequency Layer for 64QAM NRT). . . . . . 903
PrefLayer64QAMNRT (Preferred Layer for 64QAM NRT) . . . . . . . . . . 904
PFL64QAMStr (Preferred Frequency Layer for 64QAM Streaming) . . 905
PrefLayer64QAMStr (Preferred Layer for 64QAM Streaming) . . . . . . . 906
PFLCSHSAMR (Preferred Frequency Layer for CS voice HSPA AMR). . .
907
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
25.13.1
25.14
25.14.1
25.15
25.15.1
25.16
25.16.1
25.17
25.18
25.18.1
25.19
25.19.1
25.20
25.20.1
25.21
25.21.1
25.22
25.22.1
25.23
25.23.1
25.24
25.24.1
25.25
25.25.1
25.26
25.26.1
25.27
25.27.1
25.28
25.28.1
25.29
25.29.1
25.30
25.30.1
DN70456011
PrefLayerCSHSAMR (Preferred Layer for CS voice HSPA AMR). . . . 908
PFLCSHSAMRNRT (Preferred Frequency Layer for CS voice HSPA AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 909
PrefLayerCSHSAMRNRT (Preferred Layer for CS voice HSPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910
PFLCSHSNRT (Preferred Frequency Layer for CS voice HSPA NRT) 911
PrefLayerCSHSNRT (Preferred Layer for CS voice HSPA NRT) . . . . 912
PFLCSHSStr (Preferred Frequency Layer for CS voice HSPA Streaming)
913
PrefLayerCSHSStr (Preferred Layer for CS voice HSPA Streaming) . 913
PFLChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 914
PFLDBHSDAMR (Preferred Frequency Layer for DB-DC-HSDPA AMR) .
915
PrefLayerDBHSDAMR (Preferred Layer for DB-DC-HSDPA AMR) . . 916
PFLDBHSDAMRNRT (Preferred Frequency Layer for DB-DC-HSDPA
AMR and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917
PrefLayerDBHSDAMRNRT (Preferred Layer for DB-DC-HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 918
PFLDBHSDNRT (Preferred Frequency Layer for DB-DC-HSDPA NRT) .
919
PrefLayerDBHSDNRT (Preferred Layer for DB-DC-HSDPA NRT) . . . 920
PFLDBHSDStr (Preferred Frequency Layer for DB-DC-HSDPA Streaming)
921
PrefLayerDBHSDStr (Preferred Layer for DB-DC-HSDPA Streaming) 922
PFLDCHSDAMR (Preferred Frequency Layer for DC-HSDPA AMR) . 923
PrefLayerDCHSDAMR (Preferred Layer for DC-HSDPA AMR) . . . . . 924
PFLDCHSDAMRNRT (Preferred Frequency Layer for DC-HSDPA AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 925
PrefLayerDCHSDAMRNRT (Preferred Layer for DC-HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 925
PFLDCHSDNRT (Preferred Frequency Layer for DC-HSDPA NRT) . 927
PrefLayerDCHSDNRT (Preferred Layer for DC-HSDPA NRT) . . . . . . 927
PFLDCHSDStr (Preferred Frequency Layer for DC-HSDPA Streaming) .
928
PrefLayerDCHSDStr (Preferred Layer for DC-HSDPA Streaming) . . . 929
PFLDCMIAMR (Preferred Frequency Layer for DC and MIMO AMR). 930
PrefLayerDCMIAMR (Preferred Layer for DC and MIMO AMR) . . . . . 931
PFLDCMIAMRNRT (Preferred Frequency Layer for DC and MIMO AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 932
PrefLayerDCMIAMRNRT (Preferred Layer for DC and MIMO AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933
PFLDCMINRT (Preferred Frequency Layer for DC and MIMO NRT) . 934
PrefLayerDCMINRT (Preferred Layer for DC and MIMO NRT). . . . . . 935
PFLDCMIStr (Preferred Frequency Layer for DC and MIMO Streaming) .
936
PrefLayerDCMIStr (Preferred Layer for DC and MIMO Streaming). . . 936
PFLFDPCHAMR (Preferred Frequency Layer for FDPCH AMR) . . . . 937
PrefLayerFDPCHAMR (Preferred Layer for F-DPCH AMR) . . . . . . . . 938
Id:0900d80580931b1d
Confidential
15
Radio Network Parameters in Flexi Direct
25.31
25.31.1
25.32
25.32.1
25.33
25.33.1
25.34
25.34.1
25.35
25.35.1
25.36
25.36.1
25.37
25.37.1
25.38
25.38.1
25.39
25.39.1
25.40
25.40.1
25.41
25.41.1
25.42
25.42.1
25.43
25.43.1
25.44
25.45
25.45.1
25.46
25.46.1
25.47
25.47.1
25.48
25.48.1
25.49
25.49.1
25.50
25.50.1
16
PFLFDPCHAMRNRT (Preferred Frequency Layer for FDPCH AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 939
PrefLayerFDPCHAMRNRT (Preferred Layer for F-DPCH AMR and NRT)
940
PFLFDPCHNRT (Preferred Frequency Layer for FDPCH NRT) . . . . . 941
PrefLayerFDPCHNRT (Preferred Layer for F-DPCH NRT) . . . . . . . . . 942
PFLFDPCHStr (Preferred Frequency Layer for FDPCH Streaming) . . 943
PrefLayerFDPCHStr (Preferred Layer for F-DPCH Streaming) . . . . . . 943
PFLFastMovUECS (Preferred Frequency Layer for fast moving UE CS). .
944
PrefLayerFastMovUECS (Preferred Layer for fast moving UE CS) . . . 945
PFLFastMovUEPS (Preferred Frequency Layer for fast moving UE PS) . .
946
PrefLayerFastMovUEPS (Preferred Layer for fast moving UE PS) . . . 947
PFLHSDPAAMR (Preferred Frequency Layer for HSDPA AMR) . . . . . 948
PrefLayerHSDPAAMR (Preferred Layer for HSDPA AMR) . . . . . . . . . 949
PFLHSDPAAMRNRT (Preferred Frequency Layer for HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
PrefLayerHSDPAAMRNRT (Preferred Layer for HSDPA AMR and NRT) .
951
PFLHSDPANRT (Preferred Frequency Layer for HSDPA NRT) . . . . . 952
PrefLayerHSDPANRT (Preferred Layer for HSDPA NRT) . . . . . . . . . . 953
PFLHSDPAStr (Preferred Frequency Layer for HSDPA Streaming) . . 954
PrefLayerHSDPAStr (Preferred Layer for HSDPA Streaming) . . . . . . . 954
PFLHSPAAMR (Preferred Frequency Layer for HSPA AMR) . . . . . . . 955
PrefLayerHSPAAMR (Preferred Layer for HSPA AMR) . . . . . . . . . . . . 956
PFLHSPAAMRNRT (Preferred Frequency Layer for HSPA AMR and NRT)
957
PrefLayerHSPAAMRNRT (Preferred Layer for HSPA AMR and NRT) 958
PFLHSPANRT (Preferred Frequency Layer for HSPA NRT) . . . . . . . . 959
PrefLayerHSPANRT (Preferred Layer for HSPA NRT) . . . . . . . . . . . . 960
PFLHSPAStr (Preferred Frequency Layer for HSPA Streaming) . . . . . 961
PrefLayerHSPAStr (Preferred Layer for HSPA Streaming) . . . . . . . . . 961
PFLIdentifier (PFL Identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 962
PFLMIMOAMR (Preferred Frequency Layer for MIMO AMR) . . . . . . . 963
PrefLayerMIMOAMR (Preferred Layer for MIMO AMR) . . . . . . . . . . . . 964
PFLMIMOAMRNRT (Preferred Frequency Layer for MIMO AMR and NRT)
965
PrefLayerMIMOAMRNRT (Preferred Layer for MIMO AMR and NRT) 966
PFLMIMONRT (Preferred Frequency Layer for MIMO NRT) . . . . . . . . 967
PrefLayerMIMONRT (Preferred Layer for MIMO NRT) . . . . . . . . . . . . 968
PFLMIMOStr (Preferred Frequency Layer for MIMO Streaming) . . . . . 969
PrefLayerMIMOStr (Preferred Layer for MIMO Streaming) . . . . . . . . . 969
PFLR99AMR (Preferred Frequency Layer for R99 AMR). . . . . . . . . . . 970
PrefLayerR99AMR (Preferred Layer for R99 AMR) . . . . . . . . . . . . . . . 971
PFLR99AMRNRT (Preferred Frequency Layer for R99 AMR and NRT) . .
972
PrefLayerR99AMRNRT (Preferred Layer for R99 AMR and NRT) . . . . 973
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
25.51
25.51.1
25.52
25.52.1
PFLR99NRT (Preferred Frequency Layer for R99 NRT). . . . . . . . . . .
PrefLayerR99NRT (Preferred Layer for R99 NRT) . . . . . . . . . . . . . . .
PFLR99Str (Preferred Frequency Layer for R99 Streaming). . . . . . . .
PrefLayerR99Str (Preferred Layer for R99 Streaming) . . . . . . . . . . . .
26
26.1
26.2
26.3
26.4
26.5
26.6
RNAC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 978
AMRLoadTxPower (Indicator for downlink radio power load) . . . . . . . 978
AMRNumofReconf (AMRNumofReconf) . . . . . . . . . . . . . . . . . . . . . . . 978
AMRwinSizeSCload (AMRwinSizeSCload) . . . . . . . . . . . . . . . . . . . . . 979
AdjustmentPeriod (Adjustment period time) . . . . . . . . . . . . . . . . . . . . 980
AdjustmentRatio (Adjustment ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . 981
AutoACDecRestHysNRTQ (Automatic Access Class Decrease Restriction
Level Hysteresis for NRT queue length trigger). . . . . . . . . . . . . . . . . . 983
AutoACDecRestHysRTWP (Automatic Access Class Decrease Restriction
Level Hysteresis for Received Total Wideband Power trigg). . . . . . . . 984
AutoACIncRestHysNRTQ (Automatic Access Class Increase Restriction
Level Hysteresis for NRT queue length trigger). . . . . . . . . . . . . . . . . . 985
AutoACIncRestHysRTWP (Automatic Access Class Increase Restriction
Level Hysteresis for Received Total Wideband Powertrigge) . . . . . . . 986
AutoACMaxRestLevel (Automatic Access Class Maximum Restriction Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 987
AutoACRLevelUpdInt (Automatic Access Class Restriction Level Update
Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 988
AutoACRTrigRNCLoad (Automatic Access Class Restriction Trigger of
RNC Load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 989
AutoACRestForCellPCH (Access Restriction for Cell_PCH state UE) 991
BitRateSetPSNRT (Bit rate set for PS NRT DCHs) . . . . . . . . . . . . . . . 992
DCHSlopeOfTheCurve (DCH slope of the curve) . . . . . . . . . . . . . . . . 993
DLInLoopPCStepSizeCPC (DL inner loop PC step size for CPC users). .
994
DLLoadSource (DL Load Source) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995
DLmaxBitRatePerSF (Maximum DL bit rate per spreading factor) . . . 996
DLmaxBitRateSF128 (Maximum DL bit rate with spreading factor 128) . .
997
DLmaxBitRateSF16 (Maximum DL bit rate with spreading factor 16) . 998
DLmaxBitRateSF256 (Maximum DL bit rate with spreading factor 256) . .
999
DLmaxBitRateSF32 (Maximum DL bit rate with spreading factor 32) 1000
DLmaxBitRateSF64 (Maximum DL bit rate with spreading factor 64) 1001
DLpuncturingLimit (Downlink puncturing limit). . . . . . . . . . . . . . . . . . 1002
DownlinkInnerLoopPCStepSize (Power-adjusting step size in WCDMA
BTS for DL closed loop PC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1004
DynHSUPABLERAlgTrgTime (Time to trigger Dyn HSUPA BLER Algorithm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005
DynHSUPABLERBurstDataRx (Retransmissions in Dyn HSUPA BLER for
Bursty Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006
DynHSUPABLERContDataRx10 (Retransmissions in Dyn HSUPA BLER
for Cont Data 10msTTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
DynHSUPABLERContDataRx2 (Retransmissions in Dyn HSUPA BLER for
Cont Data 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009
26.7
26.8
26.9
26.10
26.11
26.12
26.13
26.14
26.15
26.16
26.17
26.18
26.18.1
26.18.2
26.18.3
26.18.4
26.18.5
26.19
26.20
26.21
26.22
26.23
26.24
DN70456011
Id:0900d80580931b1d
Confidential
974
975
976
977
17
Radio Network Parameters in Flexi Direct
26.25
26.26
26.27
26.28
26.29
26.30
26.31
26.32
26.33
26.34
26.35
26.36
26.37
26.38
26.39
26.39.1
26.39.2
26.39.3
26.39.4
26.40
26.40.1
26.40.2
26.40.3
26.40.4
26.41
26.42
26.43
26.44
18
DynHSUPABLERFrameWinSiz (Window size for FP Frames Measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010
DynHSUPABLERMaxRateThrB (Peak rate threshold for bursty data of Dyn
HSUPA BLER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1011
DynHSUPABLERMaxRateThrC10 (Peak rate thr for cont data of Dyn HSUPA BLER 10 ms TTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1012
DynHSUPABLERMaxRateThrC2 (Peak rate thr for cont data of Dyn HSUPA BLER 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1013
DynHSUPABLERPeakRateRx (Retransmissions in Dyn HSUPA BLER for
Peak data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1014
DynHSUPABLERThrBurstyTP (Bursty Data throughput threshold per TTI)
1016
DynHSUPABurstyPeriod (Bursty Period for Dyn HSUPA BLER) . . . . 1017
EDCHSlopeOfTheCurve (EDCH slope of the curve) . . . . . . . . . . . . . 1018
ExpectReorderingPDCP (Expect Reordering for PDCP) . . . . . . . . . . 1019
FOLPCSIRTgtModInt (Faster OLPC SIR target modification interval) 1020
FOLPCStepSizSIRTgt (Faster OLPC step size of SIR target changes) . . .
1021
FmaxPeriodPDCP (F Max Period for PDCP) . . . . . . . . . . . . . . . . . . . 1022
FmaxTimePDCP (F Max Time for PDCP) . . . . . . . . . . . . . . . . . . . . . 1023
FreePtxSafetyMarginStr (Safety margin for free transmitted power for
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1024
GainFactorControlPartPRACHmessage (Gain factor for control part of
PRACH message). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1025
PrachBetaC120 (Gain factor for control part of PRACH message with 120
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1026
PrachBetaC15 (Gain factor for control part of PRACH message with 15
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027
PrachBetaC30 (Gain factor for control part of PRACH message with 30
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1028
PrachBetaC60 (Gain factor for control part of PRACH message with 60
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1029
GainFactorDataPartPRACHmessage (Gain factor for data part of PRACH
message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1030
PrachBetaD120 (Gain factor for data part of PRACH message with 120
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1031
PrachBetaD15 (Gain factor for data part of PRACH message with 15 ksps)
1032
PrachBetaD30 (Gain factor for data part of PRACH message with 30 ksps)
1033
PrachBetaD60 (Gain factor for data part of PRACH message with 60 ksps)
1034
HSFACHDiscardTimer (Discard Timer for BCCH, CCCH and DCCH data
on HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035
HSFACHResetTimer (MAC-ehs Reset Timer for xCCH data on HS-FACH)
1037
HeaderCompressionMethod (Header compression algorithm of PDCP) . .
1038
L1BurstDataBLERTrgtEDCH (Layer1 Bursty Data BLER target for E-DCH)
1039
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
26.45
26.46
26.47
26.48
26.49
26.50
26.51
26.52
26.53
26.54
26.55
26.56
26.57
26.58
26.59
26.60
26.61
26.62
26.63
26.64
26.65
26.66
26.67
26.68
26.69
26.70
26.71
26.72
26.73
26.74
26.75
26.76
26.77
26.78
26.79
DN70456011
L1ContBLERTrgtEDCH10 (Layer1 Continuous BLER target for E-DCH TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1040
L1ContBLERTrgtEDCH2 (Layer1 Continuous BLER target for E-DCH TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1041
L1PeakRateBLERTrgtEDCH (Layer1 Peak Data Rate BLER target for EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1042
LoadBasedAMRCodecMode (Usage of Load based AMR codec mode selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1044
MaxAdjustmentStep (Maximum adjustment step) . . . . . . . . . . . . . . . 1044
MaxFreezingTime (Maximum freezing time) . . . . . . . . . . . . . . . . . . . 1046
MaxHeaderPDCP (Max Header for PDCP) . . . . . . . . . . . . . . . . . . . . 1047
MaxNumberOfReAttemptsCong (Maximum number of re-attempts to hunt
resources) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1048
MinPrefChange (Trigger for sending the updated reference power to BTSs)
1049
NonTCPspacePDCP (Non-TCP Space for PDCP) . . . . . . . . . . . . . . 1050
PCPreamble (Uplink DPCCH power control preamble). . . . . . . . . . . 1051
PCrangeDL (Radio link downlink power control range) . . . . . . . . . . . 1052
PTTUEMappingARPCap (PTT UE mapping for ARP pre-emption capability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1053
PTTUEMappingARPPrioLevel (PTT UE mapping for ARP priority level) .
1055
PTTUEMappingARPQue (PTT UE Mapping for ARP queuing allowed) . .
1056
PTTUEMappingARPVul (PTT UE mapping for ARP pre-emption vulnerability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1058
PTTUEMappingSignInd (PTT UE mapping for Signaling indication) . 1059
PTTUEMappingTC (PTT UE mapping for Traffic Class) . . . . . . . . . . 1061
PTTUEMappingTHP (PTT UE mapping for Traffic handling priority). 1062
PagingRestrictionInd (Paging Restriction Indication for PPAC). . . . . 1064
PeriodULRCAMR (Period for CS AMR RRC TFC control requests) . 1065
PrefSubtract (Reference power subtraction parameter) . . . . . . . . . . 1066
RAU_LAU_RestrictionInd (RAU and LAU Restriction Indication for PPAC)
1067
RNACChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . 1068
RNACId (RNAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069
RNARDSACCell_DCH (Access class restriction level for Cell_DCH) 1070
RNARDSACCell_PCH (Access class restriction level for Cell_PCH) 1071
RNARDSACGuardTime (Access class restriction guard time) . . . . . 1073
RRCConnSetupMsgSize (RRC Connection Setup Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074
SRBDelay (SRB delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1076
SignallingLinkInactivityTimer (Signalling link inactivity timer) . . . . . . 1077
StepSizeForDCHBLER (Step Size for DCH BLER calculation). . . . . 1078
StepSizeForEDCHBLER (Step Size for EDCH BLER calculation) . . 1079
TCPspacePDCP (TCP Space for PDCP) . . . . . . . . . . . . . . . . . . . . . 1080
TDMultForHSDPAStreaming (Transfer Delay multiplier for HSDPA streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1081
Id:0900d80580931b1d
Confidential
19
Radio Network Parameters in Flexi Direct
26.80
26.81
26.82
26.82.1
26.82.2
26.82.3
26.82.4
26.82.5
26.82.6
26.83
26.84
26.85
26.86
27
27.1
27.2
27.3
27.4
27.5
27.6
27.7
27.8
27.9
27.10
27.11
27.12
27.13
27.14
27.15
27.16
27.17
27.18
27.19
27.20
27.21
27.22
20
TFDCHZeroBitRate (Zero size transport block to L1 CRC calculation) . . .
1082
ULFastOLPCDTXthld (DTX threshold for uplink faster outer loop). . . 1083
ULmaxBitRatePerSF (Maximum UL bit rate per spreading factor) . . . 1085
ULmaxBitRateSF128 (Maximum UL bit rate with spreading factor 128) . .
1086
ULmaxBitRateSF16 (Maximum UL bit rate with spreading factor 16) 1087
ULmaxBitRateSF256 (Maximum UL bit rate with spreading factor 256) . .
1088
ULmaxBitRateSF32 (Maximum UL bit rate with spreading factor 32) 1089
ULmaxBitRateSF64 (Maximum UL bit rate with spreading factor 64) 1090
ULmaxBitRateSF8 (Maximum UL bit rate with spreading factor 8) . . 1091
ULpuncturingLimit (Uplink puncturing limit) . . . . . . . . . . . . . . . . . . . . 1092
UlScrCodeMin (Uplink scrambling code minimum value) . . . . . . . . . . 1093
UpLinkInitialTransmitPowerMode (Initial transmit power in uplink compressed mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1095
UpLinkRecoveryPeriodPowerMode (Recovery Period Power in UL Compressed Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1096
RNFC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1098
AMRWithEDCH (Usage of AMR service with E-DCH) . . . . . . . . . . . . 1098
AMRWithHSDSCH (Usage of AMR service with HS-DSCH) . . . . . . . 1099
AutoACResEnabled (Automatic Access Class Restriction Enabled) . 1101
AutomDLPlanUpdEnabled (Automatic DL Plan update enabled) . . . . 1103
CCCHforCUCallowed (Usage of CCCH for Cell/URA Update Confirm allowed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104
CMmasterSwitch (Compressed mode master switch) . . . . . . . . . . . . 1105
CSFBEnabled (CSFB Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1106
CSVoiceServiceSupport (CS Voice Service Support in FD-RNC) . . . 1107
CUCforPCHtoDCHallowed (Direct State Transition From Cell_PCH to
Cell_DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1108
CVUserInactInSignConnRel (Cause value usage in NAS signaling connection release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1109
DCH00SuppOnIurEnabled (DCH 0/0 Support On Iur Enabled) . . . . . 1110
DCHBitRateBalancing (DCH bit rate balancing on/off switch) . . . . . . 1111
DCHScheOverIur (DCH Scheduling Over Iur) . . . . . . . . . . . . . . . . . . 1112
DCHtoPCHEnabled (Enabling direct Cell_DCH to PCH state transition) . .
1113
DLOptimisationUsage (Dynamic link optimisation usage) . . . . . . . . . 1114
DLPSGTPDataThroughputMax (Maximum allowed DL PS GTP data
throughput) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1115
DynUsageHSDPAReturnChannel (Dynamic usage of UL NRT DCH HSDPA return Channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1116
EUTRAdetection (E-UTRA detection). . . . . . . . . . . . . . . . . . . . . . . . . 1117
EmergencyCallISHOSupport (Emergency Call lSHO Support) . . . . . 1118
EmergencyCallRedirect (Emergency Call Redirect) . . . . . . . . . . . . . . 1119
FRLCEnabled (Flexible RLC Enabled) . . . . . . . . . . . . . . . . . . . . . . . . 1120
FastDormancyEnabled (Fast Dormancy activation / de-activation parameter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1121
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
27.23
27.24
27.25
27.26
27.27
27.28
27.29
27.30
27.31
27.32
27.33
27.34
27.35
27.36
27.37
27.38
27.39
27.40
27.41
27.42
27.43
27.44
27.45
27.46
27.47
27.48
27.49
27.50
27.51
27.52
27.53
27.54
27.55
27.56
27.57
27.58
27.59
27.60
DN70456011
FastPCHSwitchEnabled (Enabling Fast Cell_PCH Switching feature)1122
FasterOLPCEnabled (Faster OLPC Enabled) . . . . . . . . . . . . . . . . . . 1123
FemtoHandoverControl (Femto Handover Control). . . . . . . . . . . . . . 1125
FlexULRLCEnabled (Flexible UL RLC Enabled) . . . . . . . . . . . . . . . . 1126
FlexUpgrUsage (Usage of the Flexible Upgrade of the NRT DCH data rate)
1127
HLSModeSelection (Higher Layer Scheduling mode selection) . . . . 1128
HSDPA16KBPSReturnChannel (HSDPA 16 kbps UL DCH return channel
on/off switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1129
HSDPA48UsersEnabled (HSDPA 48 users enabled) . . . . . . . . . . . . 1131
HSDPADynamicResourceAllocation (HSDPA Dynamic Resource Allocation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1132
HSDPAMobility (Serving HS-DSCH cell change and SHO on/off switch) .
1133
HSPAInterRNCMobility (HSPA Inter-RNC Mobility) . . . . . . . . . . . . . 1134
HSPAOverIurExt (HSPA Over Iur Extension) . . . . . . . . . . . . . . . . . . 1136
HSUPADynBLEREnabled (HSUPA Dynamic BLER Enabled) . . . . . 1137
IFHOOverIurExt (IFHO Over Iur Extension) . . . . . . . . . . . . . . . . . . . 1138
ISHOCancellation (Inter-System Handover Cancellation) . . . . . . . . . 1139
ISHOInIurMobility (ISHO In Iur Mobility) . . . . . . . . . . . . . . . . . . . . . . 1140
IntelligentEmergencyCallISHOSupport (Intelligent Emergency Call ISHO
Support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1141
IuPSrelWait3G2GMultiServ (Time supervision for releasing Iu-PS connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1142
LFDProfEnabled (LFD profiling Enabled) . . . . . . . . . . . . . . . . . . . . . 1143
MIBPLMNIdIncluded (MIB PLMN Identity Included) . . . . . . . . . . . . . 1144
MOCNenabled (Multi-Operator Core Network enabled) . . . . . . . . . . 1145
PBSpolicy (Priority based scheduling policy). . . . . . . . . . . . . . . . . . . 1146
PPACEnabled (Paging Permission With Access Control Enabled) . . 1148
PSOpThroUsage (Throughput based optimisation of the PS algorithm usage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150
PTTEnabled (Push to talk enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 1153
PWSMDriftAllowed (Cell shutdown allowed with drifting UE) . . . . . . 1155
PostVerifPeriodDLSynch (Post-verification period in downlink synchronization) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1156
PowerBalancing (Power Balancing on/off). . . . . . . . . . . . . . . . . . . . . 1157
RABDRAEnabled (Usage of the direct resource allocation for PS NRT HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1159
RNFCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1160
RNFCId (RNFC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1161
RRCSetupCCHEnabledR99 (RRC setup on CCH enabled for R99 UE). .
1162
SIBCapabilityCheck (SIB Capability Check) . . . . . . . . . . . . . . . . . . . 1164
SLHOCmAllowedNRT (CM allowed for NRT connection in SLHO). . 1164
SRVCCEnabled (SRVCC Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 1165
SignConnActivitySupervision (Activity supervision for NAS signaling connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1166
WPSCallRestriction (Restricting overloaded WPS calls) . . . . . . . . . . 1168
WireLessPriorityService (Usage of the Wireless Priority Service) . . . 1170
Id:0900d80580931b1d
Confidential
21
Radio Network Parameters in Flexi Direct
28
28.1
28.1.1
28.1.2
28.1.3
28.1.4
28.1.5
28.1.6
28.1.7
28.1.8
28.1.9
28.1.10
28.1.11
28.1.12
28.1.13
28.1.14
28.1.15
28.1.16
28.1.17
28.1.18
28.1.19
28.2
28.2.1
28.2.2
28.2.3
28.3
28.4
28.4.1
28.4.2
28.4.3
28.4.4
28.4.5
28.4.6
28.4.7
28.4.8
28.4.9
28.4.10
28.4.11
28.4.12
28.4.13
28.5
28.5.1
28.5.2
22
RNHSPA Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1172
AARConfigTable (Application Aware RAN Configuration Table) . . . . 1172
AppGrpId (Application Group Identifier) . . . . . . . . . . . . . . . . . . . . . . . 1173
DSCPCode1 (DSCP Code1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1174
DSCPCode2 (DSCP Code2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1176
DSCPCode3 (DSCP Code3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1177
DSCPCode4 (DSCP Code4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1178
DSCPCode5 (DSCP Code5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1179
Precedence (Precedence) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1181
TargetSPIforSPI0 (Target SPI for SPI 0) . . . . . . . . . . . . . . . . . . . . . . 1182
TargetSPIforSPI1 (Target SPI for SPI 1) . . . . . . . . . . . . . . . . . . . . . . 1183
TargetSPIforSPI10 (Target SPI for SPI 10) . . . . . . . . . . . . . . . . . . . . 1185
TargetSPIforSPI11 (Target SPI for SPI 11) . . . . . . . . . . . . . . . . . . . . 1186
TargetSPIforSPI2 (Target SPI for SPI 2 ) . . . . . . . . . . . . . . . . . . . . . . 1188
TargetSPIforSPI3 (Target SPI for SPI 3 ) . . . . . . . . . . . . . . . . . . . . . . 1189
TargetSPIforSPI4 (Target SPI for SPI 4) . . . . . . . . . . . . . . . . . . . . . . 1191
TargetSPIforSPI5 (Target SPI for SPI 5) . . . . . . . . . . . . . . . . . . . . . . 1192
TargetSPIforSPI6 (Target SPI for SPI 6) . . . . . . . . . . . . . . . . . . . . . . 1194
TargetSPIforSPI7 (Target SPI for SPI 7) . . . . . . . . . . . . . . . . . . . . . . 1195
TargetSPIforSPI8 (Target SPI for SPI 8) . . . . . . . . . . . . . . . . . . . . . . 1197
TargetSPIforSPI9 (Target SPI for SPI 9) . . . . . . . . . . . . . . . . . . . . . . 1198
ARPWeight (ARP based weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200
WeightForARP1 (Weight for ARP1) . . . . . . . . . . . . . . . . . . . . . . . . . . 1201
WeightForARP2 (Weight for ARP2) . . . . . . . . . . . . . . . . . . . . . . . . . . 1202
WeightForARP3 (Weight for ARP3) . . . . . . . . . . . . . . . . . . . . . . . . . . 1203
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA). . . 1204
CPCNRT10msTTI (CPC NRT 10 ms TTI) . . . . . . . . . . . . . . . . . . . . . 1205
N10msCPCOptObjective (CPC Optimization objective NRT 10ms TTI) . .
1206
N10msCQIDTXTimer (CQI DTX Timer NRT 10ms TTI) . . . . . . . . . . . 1207
N10msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 10ms TTI)
1209
N10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle NRT
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210
N10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 NRT
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1211
N10msMACDTXCycle (MAC DTX Cycle NRT 10ms TTI) . . . . . . . . . 1213
N10msMACInacThr (MAC Inactivity Threshold NRT 10ms TTI) . . . . 1214
N10msUEDPCCHburst1 (UE DPCCH burst1 NRT 10ms TTI) . . . . . . 1215
N10msUEDPCCHburst2 (UE DPCCH burst2 NRT 10ms TTI) . . . . . . 1216
N10msUEDRXCycle (UE DRX Cycle NRT 10ms TTI) . . . . . . . . . . . . 1217
N10msUEDTXCycle1 (UE DTX Cycle 1 NRT 10ms TTI) . . . . . . . . . . 1218
N10msUEDTXCycle2 (UE DTX Cycle 2 NRT 10ms TTI) . . . . . . . . . . 1219
N10msUEDTXLongPreamble (UE DTX Long Preamble N10ms). . . . 1220
CPCNRT2msTTI (CPC NRT 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . 1221
N2msCPCOptObjective (CPC Optimization objective NRT 2ms TTI) 1222
N2msCQIDTXTimer (CQI DTX Timer NRT 2ms TTI) . . . . . . . . . . . . . 1223
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
28.5.3
28.5.4
28.5.5
28.5.6
28.5.7
28.5.8
28.5.9
28.5.10
28.5.11
28.5.12
28.5.13
28.6
28.6.1
28.6.2
28.6.3
28.6.4
28.6.5
28.6.6
28.6.7
28.6.8
28.6.9
28.6.10
28.6.11
28.6.12
28.6.13
28.7
28.7.1
28.7.2
28.7.3
28.7.4
28.7.5
28.7.6
28.7.7
28.7.8
28.7.9
28.7.10
28.7.11
28.7.12
28.7.13
DN70456011
N2msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 2ms TTI). .
1225
N2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle NRT
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1226
N2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 NRT
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227
N2msMACDTXCycle (MAC DTX Cycle NRT 2ms TTI) . . . . . . . . . . . 1229
N2msMACInacThr (MAC Inactivity Threshold NRT 2ms TTI) . . . . . . 1230
N2msUEDPCCHburst1 (UE DPCCH burst1 NRT 2ms TTI) . . . . . . . 1231
N2msUEDPCCHburst2 (UE DPCCH burst2 NRT 2ms TTI) . . . . . . . 1232
N2msUEDRXCycle (UE DRX Cycle NRT 2ms TTI) . . . . . . . . . . . . . 1233
N2msUEDTXCycle1 (UE DTX Cycle 1 NRT 2ms TTI) . . . . . . . . . . . 1234
N2msUEDTXCycle2 (UE DTX Cycle 2 NRT 2ms TTI) . . . . . . . . . . . 1235
N2msUEDTXLongPreamble (UE DTX Long Preamble NRT 2ms TTI) . . .
1237
CPCStreaming10msTTI (CPC Streaming 10 ms TTI) . . . . . . . . . . . . 1238
S10msCPCOptObjective (CPC Optimization objective Str 10ms TTI) 1239
S10msCQIDTXTimer (CQI DTX Timer Str 10ms TTI) . . . . . . . . . . . . 1240
S10msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 10ms TTI) .
1241
S10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Str
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1242
S10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Str
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1244
S10msMACDTXCycle (MAC DTX Cycle Str 10ms TTI) . . . . . . . . . . 1245
S10msMACInacThr (MAC Inactivity Threshold Str 10ms TTI) . . . . . 1246
S10msUEDPCCHburst1 (UE DPCCH burst1 Str 10ms TTI) . . . . . . . 1247
S10msUEDPCCHburst2 (UE DPCCH burst2 Str 10ms TTI) . . . . . . . 1248
S10msUEDRXCycle (UE DRX Cycle Str 10ms TTI) . . . . . . . . . . . . . 1249
S10msUEDTXCycle1 (UE DTX Cycle 1 Str 10ms TTI) . . . . . . . . . . . 1250
S10msUEDTXCycle2 (UE DTX Cycle 2 Str 10ms TTI) . . . . . . . . . . . 1251
S10msUEDTXLongPreamble (UE DTX Long Preamble Str 10ms TTI) . .
1252
CPCStreaming2msTTI (CPC Streaming 2 ms TTI) . . . . . . . . . . . . . . 1253
S2msCPCOptObjective (CPC Optimization objective Str 2ms TTI) . 1254
S2msCQIDTXTimer (CQI DTX Timer Str 2ms TTI) . . . . . . . . . . . . . . 1255
S2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 2ms TTI)1257
S2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Str
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1258
S2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Str
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259
S2msMACDTXCycle (MAC DTX Cycle Str 2ms TTI) . . . . . . . . . . . . 1260
S2msMACInacThr (MAC Inactivity Threshold Str 2ms TTI) . . . . . . . 1262
S2msUEDPCCHburst1 (UE DPCCH burst1 Str 2ms TTI) . . . . . . . . . 1263
S2msUEDPCCHburst2 (UE DPCCH burst2 Str 2ms TTI) . . . . . . . . . 1264
S2msUEDRXCycle (UE DRX Cycle Str 2ms TTI) . . . . . . . . . . . . . . . 1265
S2msUEDTXCycle1 (UE DTX Cycle 1 Str 2ms TTI) . . . . . . . . . . . . . 1266
S2msUEDTXCycle2 (UE DTX Cycle 2 Str 2ms TTI) . . . . . . . . . . . . . 1267
S2msUEDTXLongPreamble (UE DTX Long Preamble Str 2ms TTI) 1268
Id:0900d80580931b1d
Confidential
23
Radio Network Parameters in Flexi Direct
28.8
28.8.1
28.8.2
28.8.3
28.8.4
28.8.5
28.8.6
28.8.7
28.8.8
28.8.9
28.8.10
28.8.11
28.8.12
28.8.13
28.9
28.9.1
28.9.2
28.9.3
28.9.4
28.9.5
28.9.6
28.9.7
28.9.8
28.9.9
28.9.10
28.9.11
28.9.12
28.9.13
28.10
28.11
28.12
28.13
28.14
28.15
28.16
28.17
24
CPCVoice10msTTI (CPC Voice 10 ms TTI) . . . . . . . . . . . . . . . . . . . . 1269
V10msCPCOptObjective (CPC Optimization objective Voi 10ms TTI)1271
V10msCQIDTXTimer (CQI DTX Timer Voi 10ms TTI) . . . . . . . . . . . . 1272
V10msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 10ms TTI) .
1273
V10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Voi
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1274
V10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Voi
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1276
V10msMACDTXCycle (MAC DTX Cycle Voi 10ms TTI). . . . . . . . . . . 1277
V10msMACInacThr (MAC Inactivity Threshold Voi 10ms TTI) . . . . . . 1278
V10msUEDPCCHburst1 (UE DPCCH burst1 Voi 10ms TTI) . . . . . . . 1279
V10msUEDPCCHburst2 (UE DPCCH burst2 Voi 10ms TTI) . . . . . . . 1280
V10msUEDRXCycle (UE DRX Cycle Voi 10ms TTI) . . . . . . . . . . . . . 1281
V10msUEDTXCycle1 (UE DTX Cycle 1 Voi 10ms TTI) . . . . . . . . . . . 1282
V10msUEDTXCycle2 (UE DTX Cycle 2 Voi 10ms TTI) . . . . . . . . . . . 1283
V10msUEDTXLongPreamble (UE DTX Long Preamble Voi 10ms TTI). . .
1284
CPCVoice2msTTI (CPC Voice 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . 1285
V2msCPCOptObjective (CPC Optimization objective Voi 2ms TTI) . . 1287
V2msCQIDTXTimer (CQI DTX Timer Voi 2ms TTI) . . . . . . . . . . . . . . 1288
V2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 2ms TTI) . . .
1289
V2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Voi
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1290
V2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Voi
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1292
V2msMACDTXCycle (MAC DTX Cycle Voi 2ms TTI). . . . . . . . . . . . . 1293
V2msMACInacThr (MAC Inactivity Threshold Voi 2ms TTI) . . . . . . . . 1294
V2msUEDPCCHburst1 (UE DPCCH burst1 Voi 2ms TTI) . . . . . . . . . 1295
V2msUEDPCCHburst2 (UE DPCCH burst2 Voi 2ms TTI) . . . . . . . . . 1296
V2msUEDRXCycle (UE DRX Cycle Voi 2ms TTI) . . . . . . . . . . . . . . . 1297
V2msUEDTXCycle1 (UE DTX Cycle 1 Voi 2ms TTI) . . . . . . . . . . . . . 1298
V2msUEDTXCycle2 (UE DTX Cycle 2 Voi 2ms TTI) . . . . . . . . . . . . . 1300
V2msUEDTXLongPreamble (UE DTX Long Preamble Voi 2ms TTI) . 1301
CPICHECNOSRBHSPA (CPICH EcNo for SRB on HSPA) . . . . . . . . 1302
CPICHECNOThreEDCH2MS (CPICH ECNO Threshold for E-DCH TTI 2
ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1303
CPICHRSCPThreEDCH2MS (CPICH RSCP Threshold for E-DCH TTI 2
ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1304
CPICHRSCPThreSRBHSDPA (CPICH RSCP Threshold for SRBs on HSDPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1305
DCellVsMIMOPreference (Dual Cell versus MIMO preference) . . . . . 1306
DiscardTimerHSCSVoice (HSDPA Discard Timer for the CS voice service)
1307
DiscardTimerPTT (HSDPA Discard Timer for the PTT) . . . . . . . . . . . 1308
EDCHCTSwitchGuardTimer (E-DCH channel type switch guard timer) . . .
1310
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
28.18
28.19
28.20
28.21
28.22
28.23
28.24
28.25
28.26
28.27
28.28
28.29
28.30
28.31
28.32
28.33
28.34
28.35
28.36
28.37
28.38
28.39
28.40
28.41
28.42
28.43
28.44
28.45
28.45.1
28.45.2
DN70456011
EDCHMACdflowtputStrTtT (Low throughput time to trigger for streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1311
EDCHMaxHARQReTxStr (E-DCH max number of HARQ retransmissions
for streaming). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1312
EDCHMaxHarqReTxSRB (E-DCH maximum # of HARQ retransmissions
for 10 ms SRB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1313
EDCHMaxHarqReTxSRB2MS (E-DCH maximum # of HARQ retransmissions for 2 ms SRB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1314
EDCHMaxNumberOfHARQReTx (E-DCH maximum number of HARQ retransmissions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1315
EDCHQOSClasses (E-DCH QoS classes) . . . . . . . . . . . . . . . . . . . . 1316
EnablDelayHHO (Enabling Delay HHO) . . . . . . . . . . . . . . . . . . . . . . 1317
EnablDelayStand (Enabling Delay Standard) . . . . . . . . . . . . . . . . . . 1318
FDPCHAllocMinInterval (Minimum interval between F-DPCH allocations)
1319
FDPCHAndSRBOnHSPATC (F-DPCH and SRBs on HSPA per TC) 1320
FDPCHSetupEC (DCH instead of F-DPCH based on Establishment
Cause) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1321
FactorEDCHMaxBRPSstream (Factor E-DCH max. Bit Rate for PS
streaming RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1324
FactorEDCHMaxBitRate (Factor to calculate EDCH maximum bit rate) . .
1325
FactorEDCHMaxBitRate2NRT (Factor E-DCH max. Bit Rate for 2 NRT
RAB combinations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1326
FactorEDCHMaxBitRate3NRT (Factor E-DCH max. Bit Rate for 3 NRT
RAB combinations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1327
HSDPACPICHCTSRepPer (DCH to HS-DSCH switch CPICH Ec/No reporting period) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1328
HSDPACPICHEcNoThreshold (CPICH Ec/No threshold for serving HSDSCH cell change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1329
HSDPACellChangeRepetitionTime (Window for max repetitive serving HSDSCH cell changes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1330
HSDPAChaTypeSwitchWindow (HSDPA channel type switching window)
1331
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1332
HSDPAPeakRateLimitRABMax (HSDPA peak rate limitation to the RAB
maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1333
HSDPAPriority (HSDPA priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1335
HSDPARRCdiversity (SHO of the HSDPA capable UE) . . . . . . . . . . 1336
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1337
HSDSCHCTSwitchGuardTimer (HS-DSCH channel type switch guard timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1339
HSDSCHGuardTimerLowThroughput (HS-DSCH guard timer due to low
throughput) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1340
HSDSCHQoSclasses (HS-DSCH QoS classes) . . . . . . . . . . . . . . . . 1341
HSPANBRValues (HSPA NBR values) . . . . . . . . . . . . . . . . . . . . . . . 1342
NBRForPri0DL (Downlink NBR for Priority value 0) . . . . . . . . . . . . . 1344
NBRForPri0UL (Uplink NBR for Priority value 0) . . . . . . . . . . . . . . . . 1345
Id:0900d80580931b1d
Confidential
25
Radio Network Parameters in Flexi Direct
28.45.3
28.45.4
28.45.5
28.45.6
28.45.7
28.45.8
28.45.9
28.45.10
28.45.11
28.45.12
28.45.13
28.45.14
28.45.15
28.45.16
28.45.17
28.45.18
28.45.19
28.45.20
28.45.21
28.45.22
28.45.23
28.45.24
28.45.25
28.45.26
28.46
28.47
28.48
28.49
28.50
28.51
28.52
28.53
28.54
28.55
28.56
28.57
28.58
28.59
26
NBRForPri10DL (Downlink NBR for Priority value 10) . . . . . . . . . . . . 1346
NBRForPri10UL (Uplink NBR for Priority value 10) . . . . . . . . . . . . . . 1347
NBRForPri11DL (Downlink NBR for Priority value 11) . . . . . . . . . . . . 1348
NBRForPri11UL (Uplink NBR for Priority value 11) . . . . . . . . . . . . . . 1349
NBRForPri12DL (Downlink NBR for Priority value 12) . . . . . . . . . . . . 1350
NBRForPri12UL (Uplink NBR for Priority value 12) . . . . . . . . . . . . . . 1351
NBRForPri1DL (Downlink NBR for Priority value 1) . . . . . . . . . . . . . . 1352
NBRForPri1UL (Uplink NBR for Priority value 1) . . . . . . . . . . . . . . . . 1353
NBRForPri2DL (Downlink NBR for Priority value 2) . . . . . . . . . . . . . . 1354
NBRForPri2UL (Uplink NBR for Priority value 2) . . . . . . . . . . . . . . . . 1355
NBRForPri3DL (Downlink NBR for Priority value 3) . . . . . . . . . . . . . . 1356
NBRForPri3UL (Uplink NBR for Priority value 3) . . . . . . . . . . . . . . . . 1357
NBRForPri4DL (Downlink NBR for Priority value 4) . . . . . . . . . . . . . . 1358
NBRForPri4UL (Uplink NBR for Priority value 4) . . . . . . . . . . . . . . . . 1359
NBRForPri5DL (Downlink NBR for Priority value 5) . . . . . . . . . . . . . . 1360
NBRForPri5UL (Uplink NBR for Priority value 5) . . . . . . . . . . . . . . . . 1361
NBRForPri6DL (Downlink NBR for Priority value 6) . . . . . . . . . . . . . . 1362
NBRForPri6UL (Uplink NBR for Priority value 6) . . . . . . . . . . . . . . . . 1363
NBRForPri7DL (Downlink NBR for Priority value 7) . . . . . . . . . . . . . . 1364
NBRForPri7UL (Uplink NBR for Priority value 7) . . . . . . . . . . . . . . . . 1365
NBRForPri8DL (Downlink NBR for Priority value 8) . . . . . . . . . . . . . . 1366
NBRForPri8UL (Uplink NBR for Priority value 8) . . . . . . . . . . . . . . . . 1367
NBRForPri9DL (Downlink NBR for Priority value 9) . . . . . . . . . . . . . . 1368
NBRForPri9UL (Uplink NBR for Priority value 9) . . . . . . . . . . . . . . . . 1369
HSPDSCHAdjustPeriod (HS-PDSCH code adjustment period) . . . . . 1370
HappyBitDelayConditionEDCH (Happy bit delay condition for E-DCH) . . .
1371
HsdschGuardTimerHO (HS-DSCH guard time after switching to DCH due
to HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1372
InacUserNbrXXXOverNRT (Inactive users number in XXX over NRT) . . .
1374
InacUsersOverloadFact (Inactive users overload preventive factor) . 1374
InitialSPINRT (Initial SPI for PS NRT RAB) . . . . . . . . . . . . . . . . . . . . 1376
MACdflowthroughputRelThr (Low throughput threshold of the MAC-d flow)
1378
MACdflowthroughputTimetoTrigger (Low throughput time to trigger of the
MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1379
MACdflowtputStrTtT (Low throughput time to trigger of streaming MAC-d
flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1380
MACdflowutilStrTtT (Low util time to trigger of MAC-d flow for streaming) .
1381
MEHCQIFeedbackCycle (Temporary CQI feedback cycle for the Mass
Event Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1382
MEHHSUPAUserIncr (HSUPA user increment for the Mass Event Handler)
1384
MaxBitRateNRTMACDFlow (Maximum bit rate of NRT MAC-d flow) . 1385
MaxCSDelayRNCETTI10 (Max buffer time of the HS CS voice in RNC ETTI 10 ms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1387
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
28.60
28.61
28.62
28.63
28.64
28.65
28.66
28.67
28.68
28.69
28.70
28.71
28.72
28.73
28.74
28.75
28.76
28.77
28.78
28.79
28.80
28.81
28.82
28.83
28.84
28.85
28.86
28.87
28.87.1
DN70456011
MaxCSDelayRNCETTI2 (Max buffer time of the HS CS voice in RNC E-TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1389
MaxCSDelayUE (Max buffer time of the HS CS voice in UE) . . . . . . 1390
MaxEHARQReTxCSAMR10 (E-DCH max number of retransmissions CS
voice E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1391
MaxEHARQReTxCSAMR2 (E-DCH max number of retransmissions CS
voice E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1392
MaxEHARQReTxPSconv10 (E-DCH max number of retransmissions PS
conv E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1393
MaxEHARQReTxPSconv2 (E-DCH max number of retransmissions PS
conv E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1394
MaxReWaitTime (Maximum Reordering Wait Time for MAC-es) . . . 1395
MaxReWaitTime2msTTI (Maximum Reordering Wait Time for Mac-es EDCH 2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1396
MaxReWaitTime2msTTI16 (Maximum reordering wait time parameter for
MAC-es E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1397
MaxReWaitTimeRT (Maximum MAC-es Reordering Wait time for RT user)
1398
MaxSetOfEDPDCHCSAMR10 (Maximum Set of E-DPDCHs for CS voice
E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1399
MaxSetOfEDPDCHCSAMR2 (Maximum Set of E-DPDCHs for CS voice ETTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400
NRTRBBRWithEDCHStr (NRT RB user bit rate with E-DCH streaming) .
1401
PTTRLCPDUSizeHSDSCH (RLC PDU size for PTT mapped to HS-DSCH)
1403
PeriodicityForSI (Periodicity for scheduling info) . . . . . . . . . . . . . . . . 1404
PowerOffsetEHARQPSConv (HARQ power offset for E-DCH MAC-d flow
of PS conv) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1405
PowerOffsetEHARQVoice (HARQ power offset for E-DCH MAC-d flow of
CS voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1406
PowerOffsetForSI (Power Offset for Scheduling Info) . . . . . . . . . . . . 1407
RNHSPAChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . 1408
RNHSPAId (RNHSPA Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1409
SmartHSPATimeToTrigger (Time-to-trigger for Smartphone throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410
SmartHSPATputAveWin (Window size for Smartphone throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1411
T1HSCSVoice (HSDPA re-ordering release timer T1 for the CS voice) . .
1412
T1HSFACH (HSDPA re-ordering release timer T1 for xCCH on HS-FACH)
1413
T1PTT (HSDPA re-ordering rel timer T1 for the PTT) . . . . . . . . . . . . 1414
TGPLAMRHSDPAInterFreq (TGPL for AMR and HSDPA and IF measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1416
TGPLHSDPAInterFreq (TGPL for HSDPA and IF measurement) . . . 1417
ThresholdMaxEDPDCHSR (Threshold to define maximum E-DPDCH SR)
1418
ThresholdMaxEDPDCHSR1920kbps (Threshold to define maximum EDPDCH SR 1920 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1419
Id:0900d80580931b1d
Confidential
27
Radio Network Parameters in Flexi Direct
28.87.2
28.87.3
28.88
28.89
28.90
28.91
28.91.1
28.91.2
28.91.3
28.91.4
28.92
28.92.1
28.92.2
28.92.3
28.92.4
29
29.1
29.2
29.3
29.4
29.5
29.6
29.7
29.8
29.9
29.10
29.11
29.12
29.13
29.14
29.15
29.16
29.17
29.18
29.19
29.20
28
ThresholdMaxEDPDCHSR3840kbps (Threshold to define maximum EDPDCH SR 3840 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1420
ThresholdMaxEDPDCHSR960kbps (Threshold to define maximum EDPDCH SR 960 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1422
UPResAllocInCellDCHWait (Retry time for u-plane resource allocation in
Cell_DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1423
VCPHSDPAPrevDuration (Duration of HSDPA prevention for Voice Call
Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1425
VCPHSDPAUserIncr (HSDPA user increment for the Voice Call Priority) .
1426
WeightDCH (Weight of NRT DCH UE) . . . . . . . . . . . . . . . . . . . . . . . . 1428
WeightDCHBG (Weight of NRT DCH UE BG RAB) . . . . . . . . . . . . . . 1429
WeightDCHTHP1 (Weight of NRT DCH UE THP1 RAB) . . . . . . . . . . 1430
WeightDCHTHP2 (Weight of NRT DCH UE THP2 RAB) . . . . . . . . . . 1431
WeightDCHTHP3 (Weight of NRT DCH UE THP3 RAB) . . . . . . . . . . 1432
WeightHSPA (Weight of HSPA UE) . . . . . . . . . . . . . . . . . . . . . . . . . . 1433
WeightHSPABG (Weight of HSPA UE BG RAB) . . . . . . . . . . . . . . . . 1434
WeightHSPATHP1 (Weight of HSPA UE THP1 RAB) . . . . . . . . . . . . 1435
WeightHSPATHP2 (Weight of HSPA UE THP2 RAB) . . . . . . . . . . . . 1436
WeightHSPATHP3 (Weight of HSPA UE THP3 RAB) . . . . . . . . . . . . 1437
RNMOBI Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1439
AnchorFmciIdentifier (Anchor FMCI Identifier) . . . . . . . . . . . . . . . . . . 1439
AnchorFmcsIdentifier (Anchor FMCS Identifier) . . . . . . . . . . . . . . . . . 1439
AnchorHopiIdentifier (Anchor HOPI Identifier) . . . . . . . . . . . . . . . . . . 1440
AnchorHopsIdentifier (Anchor HOPS Identifier) . . . . . . . . . . . . . . . . . 1441
BlindGsmHoCS (Blind GSM handover for CS RAB). . . . . . . . . . . . . . 1442
CUCEcNoThresholdCSEHO (CPICH Ec/No Threshold Value For CUC Usage in CSEHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1443
CellReselectionObservingTime (Cell Reselection Observing Time) . . 1445
DRRCForHSDPALayerServices (Services for DRRC connection setup for
HSDPA layer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1447
DefaultAuthorisedNetworkId (Identifier of the Default Authorised Network)
1448
DirectPchDchCS (Cell/URA_PCH to Cell_DCH transition due to CS call) .
1449
DirectedRRCForHSDPALayerEnhanc (DRRC connection setup for HSDPA layer enhancements). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450
DisablePowerInHSDPALayeringDecision (Disable power in decision making for HSDPA layering) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1452
EcnoDifferenceThreshold (CPICH EcNo Difference Threshold). . . . . 1453
EnableULQualDetRep (Quality deterioration report from UL OLPC controller). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1454
FastDormOverCpcPri (Fast Dormancy and CPC priority) . . . . . . . . . 1455
FastUECancel (Fast UE Cancellation) . . . . . . . . . . . . . . . . . . . . . . . . 1456
FastUEPeriod (Fast UE evaluation period) . . . . . . . . . . . . . . . . . . . . . 1457
FastUEThreshold (Fast UE Threshold). . . . . . . . . . . . . . . . . . . . . . . . 1458
GANetwARFCN (GAN ARFCN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1459
GANetwBCC (GAN BCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1460
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
29.21
29.22
29.23
29.24
29.25
29.26
29.27
29.28
29.29
29.30
29.31
29.32
29.33
29.34
29.35
29.36
29.37
29.38
29.39
29.40
29.41
29.42
29.43
29.44
29.45
29.46
29.47
29.48
29.49
29.50
29.51
29.51.1
29.52
DN70456011
GANetwNCC (GAN NCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1461
GapPositionSingleFrame (Gap position single frame). . . . . . . . . . . . 1462
GsmHandoverAMR (Handover of AMR Service to GSM) . . . . . . . . . 1463
GsmHandoverCS (Handover of CS Service to GSM) . . . . . . . . . . . . 1464
GsmHandoverNrtPS (Handover of NRT PS Service to GSM). . . . . . 1465
GsmHandoverRtPS (Handover of RT PS Service to GSM). . . . . . . . 1467
HSCAHORabCombSupport (RAB Combinations Supported by HSCAHO)
1468
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1469
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1471
HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1472
HSDPALayerLoadShareThreshold (HSDPA layers load sharing threshold)
1473
HSDPASIRErrorAveWindow (Averaging window of the SIRerror measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1475
HSDPASIRErrorFilterCoefficient (Higher layer filtering coefficient for HSDPA SIRerror) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1476
HSDPASIRErrorReportPeriod (Reporting period of the SIRerror measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1477
HSDPASIRErrorServCell (SIRerror threshold for the serving HS-DSCH
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1478
HSDPASIRErrorTargetCell (SIRerror threshold for the target cell) . . 1479
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1480
HSPADRNCEcNoOffset (DRNC Ec/No offset for HSPA Inter-RNC Cell
Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1482
HSPADRNCSIRErrorOffset (SIR error offset for HSPA Inter-RNC Cell
Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1483
IBTSRabCombSupport (RAB Combinations Supported by FD-BTS) 1484
LHOMinNrtDchAllocTime (Load handover minimum NRT DCH allocation
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1486
LowerRxTxTimeDiff (Lower Rx-Tx Time Difference Threshold) . . . . 1486
MBLBGuardTimer (MBLB Guard Timer) . . . . . . . . . . . . . . . . . . . . . . 1487
MaxBLHOAttempt (Maximum Number of BLHO Attempts) . . . . . . . . 1488
MaxCellReselections (Max cell reselections). . . . . . . . . . . . . . . . . . . 1489
MaxNumISHOClPerAS (Max Number of ISHO Cancellations Per Active
Set for a U) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1491
MultipleBSICIdent (Multiple BSIC Identification) . . . . . . . . . . . . . . . . 1491
NCHOFilterCoeffComLoadMeasDRNCCell (NCHO filter coefficient common load meas DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1492
NCHOHystComLoadMeasDRNCCell (NCHO hysteresis common load
measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1494
NCHOThrComLoadMeasDRNCCell (NCHO threshold common load measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1495
PagingGroupList (List of FD-BTS in paging group) . . . . . . . . . . . . . . 1497
PgRncId (Paging Group member I-BTS RNC-ID) . . . . . . . . . . . . . . . 1498
PagingRoleType (Current Role of FD-BTS). . . . . . . . . . . . . . . . . . . . 1498
Id:0900d80580931b1d
Confidential
29
Radio Network Parameters in Flexi Direct
29.53
29.54
29.54.1
29.54.2
29.54.3
29.55
29.55.1
29.55.2
29.55.3
29.56
29.57
29.58
29.59
29.60
29.61
29.62
29.63
29.64
29.65
29.66
29.67
29.68
29.69
29.70
29.71
29.72
29.73
29.74
29.75
30
PreferBandForLayering (Preferred Band for Layering). . . . . . . . . . . . 1499
RANAPCauseLoadHO (RANAP cause to indicate load handover) . . 1500
RANAPCause1LoadHO (RANAP cause 1 to indicate load handover) 1501
RANAPCause2LoadHO (RANAP cause 2 to indicate load handover) 1502
RANAPCause3LoadHO (RANAP cause 3 to indicate load handover) 1503
RANAPCauseServHO (RANAP cause to indicate service handover) 1504
RANAPCause1ServHO (RANAP cause 1 to indicate service handover) . .
1505
RANAPCause2ServHO (RANAP cause 2 to indicate service handover) . .
1506
RANAPCause3ServHO (RANAP cause 3 to indicate service handover) . .
1507
RNMOBIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 1508
RNMOBIId (RNMOBI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1509
SLHOHandlingOfCellLoadMeasNotAct (SLHO handling of cell load measurement is not active) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1510
SLHOProfileBackgroundPSNRTData (Service profile for background PS
NRT data in SLHO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1512
SLHOProfileConvCSSpeech (Service profile for conversational CS speech
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1513
SLHOProfileConvCSTData (Service profile for conversational CS T data in
SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1515
SLHOProfileConvPSRTData (Service profile for conversational PS RT
data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1517
SLHOProfileConvPSSpeech (Service profile for conversational PS speech
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1519
SLHOProfileInteractivePSNRTData (Service profile for interactive PS NRT
data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1521
SLHOProfileStreamCSNTData (Service profile for streaming CS NT data
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1523
SLHOProfileStreamPSRTData (Service profile for streaming PS RT data in
SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1525
SLHOUseBackgroundPSNRTData (Use of SLHO for background PS NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1527
SLHOUseConvCSSpeech (Use of SLHO for conversational CS speech) .
1529
SLHOUseConvCSTData (Use of SLHO for conversational CS transparent
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1530
SLHOUseConvPSRTData (Use of SLHO for conversational PS RT data).
1532
SLHOUseConvPSSpeech (Use of SLHO for conversational PS speech) .
1533
SLHOUseInteractivePSNRTData (Use of SLHO for interactive PS NRT data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1535
SLHOUseStreamCSNTData (Use of SLHO for streaming CS non-transparent data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1536
SLHOUseStreamPSRTData (Use of SLHO for streaming PS RT data). . .
1538
ServBtwnHSDPALayers (Services between HSDPA layers) . . . . . . . 1539
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
29.76
29.77
29.78
29.79
29.80
29.81
29.82
29.83
29.84
29.85
29.86
29.87
29.88
29.89
29.90
29.91
29.92
29.93
29.94
30
30.1
30.2
30.3
30.4
30.5
30.6
30.7
30.8
30.9
DN70456011
ServicesToHSDPALayer (Services to HSDPA layer in state transition) . .
1540
SmartLTELayeringPrevT (Timer for Smart LTE Layering Prevention) . . .
1541
SmartLTELayeringServ (Smart LTE Layering service control) . . . . . 1542
TGPLdoubleframeNRTPSgsm (Transmision gap pattern length in case of
double frame: NRT PS service and GSM measurement) . . . . . . . . . 1544
TGPLdoubleframeNRTPSinterFreq (Transmision gap pattern length in
case of double frame: NRT PS service and IF measurement) . . . . . 1545
TGPLsingleframeAMRgsm (Transmision gap pattern length in case of single frame: AMR service and GSM measurement) . . . . . . . . . . . . . . . 1546
TGPLsingleframeAMRinterFreq (Transmision gap pattern length in case of
single frame: AMR service and IF measurement) . . . . . . . . . . . . . . . 1547
TGPLsingleframeCSgsm (Transmision gap pattern length in case of single
frame: CS service and GSM measurement) . . . . . . . . . . . . . . . . . . . 1548
TGPLsingleframeCSinterFreq (Transmision gap pattern length in case of
single frame: CS service and IF measurement). . . . . . . . . . . . . . . . . 1549
TGPLsingleframeNRTPSgsm (Transmision gap pattern length in case of
single frame: NRT PS service and GSM measurement) . . . . . . . . . . 1550
TGPLsingleframeNRTPSinterFreq (Transmision gap pattern length in case
of single frame: NRT PS service and IF measurement) . . . . . . . . . . 1551
TGPLsingleframeRTPSgsm (Transmision gap pattern length in case of
single frame: RT PS service and GSM measurement) . . . . . . . . . . . 1552
TGPLsingleframeRTPSinterFreq (Transmision gap pattern length in case
of single frame: RT PS service and IF measurement) . . . . . . . . . . . . 1553
TRelocOverall (T RelocOverall) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1554
TRelocPrep (T RelocPrep). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1555
UEQualityRepInterv (UE Quality Measurement Reporting Interval) . 1555
UETxPowerMaxRef (Maximum Reference UE transmission power). 1557
ULQualDetRepThreshold (UL quality deterioration reporting threshold) . .
1558
UpperRxTxTimeDiff (Upper Rx-Tx Time Difference Threshold) . . . . 1559
RNPS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1560
ActivationTimeOffset (Offset for activation time) . . . . . . . . . . . . . . . . 1560
CellDCHtestTmr (Test timer for inactivity supervision in Cell_DCH state).
1561
CrQueuingTimeDL (Maximum downlink capacity request queuing time) .
1562
CrQueuingTimeUL (Maximum uplink capacity request queuing time) 1563
DCHUtilBelowDowngradeThr (Threshold below the downgrade bit rate) .
1564
DCHUtilHighAveWin (Window size for the high throughput measurement)
1566
DCHUtilHighBelowNRTDataRateThr (Threshold below the NRT DCH data
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1567
DCHUtilHighTimeToTrigger (Time to trigger for the high throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1569
DCHUtilLowerAveWinBitRate (Window size for the lower throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1570
Id:0900d80580931b1d
Confidential
31
Radio Network Parameters in Flexi Direct
30.9.1
30.9.2
30.9.3
30.9.4
30.9.5
30.10
30.10.1
30.10.2
30.10.3
30.10.4
30.10.5
30.11
30.11.1
30.11.2
30.11.3
30.11.4
30.11.5
30.12
30.13
30.13.1
30.13.2
30.13.3
30.13.4
30.13.5
30.14
30.14.1
30.14.2
32
DCHUtilLowerAveWin128 (Lower measurement window size for NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1572
DCHUtilLowerAveWin256 (Lower measurement window size for NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1574
DCHUtilLowerAveWin32 (Lower measurement window size for NRT DCH
of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1576
DCHUtilLowerAveWin384 (Lower measurement window size for NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1578
DCHUtilLowerAveWin64 (Lower measurement window size for NRT DCH
of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1580
DCHUtilLowerDowngradeThrBitRate (Lower downgrade threshold) . 1582
DCHUtilLowerDowngradeThr128 (Lower downgrade threshold for the NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1584
DCHUtilLowerDowngradeThr256 (Lower downgrade threshold for the NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1586
DCHUtilLowerDowngradeThr32 (Lower downgrade threshold for the NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1587
DCHUtilLowerDowngradeThr384 (Lower downgrade threshold for the NRT
DCH of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1588
DCHUtilLowerDowngradeThr64 (Lower downgrade threshold for the NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1589
DCHUtilLowerTimeToTriggerBitRate (Time to trigger for the lower throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1591
DCHUtilLowerTimeToTrigger128 (Lower time to trigger for the NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1593
DCHUtilLowerTimeToTrigger256 (Lower time to trigger for the NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1594
DCHUtilLowerTimeToTrigger32 (Lower time to trigger for the NRT DCH of
32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1595
DCHUtilLowerTimeToTrigger384 (Lower time to trigger for the NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1596
DCHUtilLowerTimeToTrigger64 (Lower time to trigger for the NRT DCH of
64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1597
DCHUtilMeasGuardTime (Guard time for throughput measurement). 1598
DCHUtilUpperAveWinBitRate (Window size for the upper throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1599
DCHUtilUpperAveWin128 (Upper measurement window size for NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1601
DCHUtilUpperAveWin256 (Upper measurement window size for NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1603
DCHUtilUpperAveWin32 (Upper measurement window size for NRT DCH
of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1605
DCHUtilUpperAveWin384 (Upper measurement window size for NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1607
DCHUtilUpperAveWin64 (Upper measurement window size for NRT DCH
of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1609
DCHUtilUpperDowngradeThrBitRate (Upper downgrade threshold) . 1611
DCHUtilUpperDowngradeThr128 (Upper downgrade threshold for the NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1613
DCHUtilUpperDowngradeThr256 (Upper downgrade threshold for the NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1615
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
30.14.3
30.14.4
30.14.5
30.15
30.15.1
30.15.2
30.15.3
30.15.4
30.15.5
30.16
30.17
30.18
30.19
30.20
30.21
30.22
30.23
30.24
30.25
30.25.1
30.25.2
30.25.3
30.25.4
30.25.5
30.25.6
30.25.7
30.25.8
30.25.9
30.25.10
DN70456011
DCHUtilUpperDowngradeThr32 (Upper downgrade threshold for the NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1616
DCHUtilUpperDowngradeThr384 (Upper downgrade threshold for the NRT
DCH of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1617
DCHUtilUpperDowngradeThr64 (Upper downgrade threshold for the NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1618
DCHUtilUpperTimeToTriggerBitRate (Time to trigger for the upper
throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1619
DCHUtilUpperTimeToTrigger128 (Upper time to trigger for the NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1621
DCHUtilUpperTimeToTrigger256 (Upper time to trigger for the NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1622
DCHUtilUpperTimeToTrigger32 (Upper time to trigger for the NRT DCH of
32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1623
DCHUtilUpperTimeToTrigger384 (Upper time to trigger for the NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1624
DCHUtilUpperTimeToTrigger64 (Upper time to trigger for the NRT DCH of
64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1625
DLOptimisationProhibitTime (Dynamic Link Optimisation prohibit time) . .
1626
DLOptimisationPwrOffset (Power offset for dynamic link optimisation) . . .
1627
FactorMinPBSinterval (Factor to determine minimum PBS interval) . 1628
HSFACHDiscardTimerDTCH (Discard Timer for DTCH data on HS-FACH)
1629
HSFACHRestTimerDTCH (MAC-ehs Reset Timer for DTCH data on HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1630
InactDetForStreamingRB (Inactivation detection for streaming radio bearer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1631
IurPriority (Priority handling over Iur-interface) . . . . . . . . . . . . . . . . . 1633
MEHTVMPendingTime (Temporary TVM pending time for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1634
PTTDormancyTimer (PTT dormancy timer). . . . . . . . . . . . . . . . . . . . 1635
QoSPriorityMapping (QoS Priority Mapping) . . . . . . . . . . . . . . . . . . . 1636
PriForBackARP1 (Priority for Background TC with ARP 1) . . . . . . . . 1640
PriForBackARP2 (Priority for Background TC with ARP 2) . . . . . . . . 1641
PriForBackARP3 (Priority for Background TC with ARP 3) . . . . . . . . 1642
PriForConvOnHSPA (Priority for conversational on HSPA) . . . . . . . 1643
PriForHSFACHDTCH (Priority for PS data over HSPA on CELL_FACH
state.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1644
PriForIntSignaling (Priority for Interactive TC marked for signaling use) . .
1645
PriForIntTHP1ARP1 (Priority for Interactive TC with THP 1 and ARP 1) .
1646
PriForIntTHP1ARP2 (Priority for Interactive TC with THP 1 and ARP 2) .
1647
PriForIntTHP1ARP3 (Priority for Interactive TC with THP 1 and ARP 3) .
1649
PriForIntTHP2ARP1 (Priority for Interactive TC with THP 2 and ARP 1) .
1650
Id:0900d80580931b1d
Confidential
33
Radio Network Parameters in Flexi Direct
30.25.11
30.25.12
30.25.13
30.25.14
30.25.15
30.25.16
30.25.17
30.25.18
30.25.19
30.26
30.27
30.28
30.29
30.30
30.31
30.32
30.33
30.34
30.35
30.36
30.36.1
30.36.2
30.36.3
30.36.4
30.36.5
30.36.6
30.37
30.38
30.38.1
34
PriForIntTHP2ARP2 (Priority for Interactive TC with THP 2 and ARP 2) . .
1651
PriForIntTHP2ARP3 (Priority for Interactive TC with THP 2 and ARP 3) . .
1652
PriForIntTHP3ARP1 (Priority for Interactive TC with THP 3 and ARP 1) . .
1653
PriForIntTHP3ARP2 (Priority for Interactive TC with THP 3 and ARP 2) . .
1654
PriForIntTHP3ARP3 (Priority for Interactive TC with THP 3 and ARP 3) . .
1655
PriForSRBsOnHSPA (Priority for SRBs on HSPA). . . . . . . . . . . . . . . 1657
PriForStreamARP1 (Priority for Streaming traffic class with ARP1) . . 1658
PriForStreamARP2 (Priority for Streaming traffic class with ARP2) . . 1659
PriForStreamARP3 (Priority for Streaming traffic class with ARP3) . . 1661
RNPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1662
RNPSId (RNPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1663
RTOverNRTPriThresholdARP1 (RT-over-NRT priority threshold for ARP1)
1664
RTOverNRTPriThresholdARP2 (RT-over-NRT priority threshold for ARP2)
1665
RTOverNRTPriThresholdARP3 (RT-over-NRT priority threshold for ARP3)
1667
RoleSwitchActAdjOffset (Role Switch activation adjustment offset) . . 1668
SmartInactTimerFACH (Inactivity Timer for Smart Phones in Cell_FACH)
1668
SmartInactivityTimerDCH (Inactivity timer for Smartphone DCH) . . . 1669
ToCellFACHinTest (Test switch for Iu release in Cell_DCH state) . . . 1670
TrafVolThresholdDLHigh (Downlink traffic volume measurement high
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1671
TrafVolThresholdDLHighBitRate (Traffic volume threshold for downlink
NRT DCH bit rates). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1674
TrafVolThresholdDLHighDCH128 (Traffic volume threshold for DL NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1676
TrafVolThresholdDLHighDCH16 (Traffic volume threshold for DL NRT
DCH of 16 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1678
TrafVolThresholdDLHighDCH256 (Traffic volume threshold for DL NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1680
TrafVolThresholdDLHighDCH32 (Traffic volume threshold for DL NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1682
TrafVolThresholdDLHighDCH64 (Traffic volume threshold for DL NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1684
TrafVolThresholdDLHighDCH8 (Traffic volume threshold for DL NRT DCH
of 8 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1686
TrafVolThresholdULHigh (Uplink traffic volume measurement high threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1687
TrafVolThresholdULHighBitRate (Traffic volume threshold for uplink NRT
DCH bit rates) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1690
TrafVolThresholdULHighDCH128 (Traffic volume threshold for UL NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1692
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
30.38.2
30.38.3
30.38.4
30.38.5
30.38.6
30.39
30.40
30.41
31
31.1
31.2
31.3
31.3.1
31.3.2
31.3.3
31.3.4
31.3.5
31.3.6
31.3.7
31.3.8
31.3.9
31.3.10
31.3.11
31.4
31.4.1
31.4.2
DN70456011
TrafVolThresholdULHighDCH16 (Traffic volume threshold for UL NRT
DCH of 16 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1694
TrafVolThresholdULHighDCH256 (Traffic volume threshold for UL NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1696
TrafVolThresholdULHighDCH32 (Traffic volume threshold for UL NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1697
TrafVolThresholdULHighDCH64 (Traffic volume threshold for UL NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1699
TrafVolThresholdULHighDCH8 (Traffic volume threshold for UL NRT DCH
of 8 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1700
TrafVolTimeToTriggerDL (Downlink traffic volume measurement time to
trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1702
TrafVolTimeToTriggerUL (Uplink traffic volume measurement time to trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1703
ULLoadStateTTT (UL loaded state time to trigger) . . . . . . . . . . . . . . 1705
RNRLC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1707
AMRLCBufMaxOverbook2NRT (AM RLC buffer max total overbooking for
2 PS RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1707
AMRLCBufMaxOverbook3NRT (AM RLC buffer max overbooking for more
than 2 PS RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1708
AMRLCHSFACHPS (AM RLC configuration for PS NRT with HS-FACH)
1709
AMRLCHSFACHPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1710
AMRLCHSFACHPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1711
AMRLCHSFACHPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1712
AMRLCHSFACHPSPeriodMax (AM RLC status period max for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1714
AMRLCHSFACHPSPeriodMin (AM RLC status period min for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1715
AMRLCHSFACHPSPollPDU (AM RLC period Poll_PDU for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1716
AMRLCHSFACHPSPollSDU (AM RLC period Poll_SDU for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1718
AMRLCHSFACHPSPollWin (AM RLC period Poll_Window for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1719
AMRLCHSFACHPSTriggers (AM RLC status report triggers for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1720
AMRLCRespHSFACHandRACH (AM RLC round trip time with HSDSCH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1722
HSFACHAMRLCRespHSRACH (AM RLC round trip time with HSDSCH/HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1723
AMRLCHSRACHPS (AM RLC configuration for PS NRT with HS-RACH)
1725
AMRLCHSRACHPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1726
AMRLCHSRACHPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1727
Id:0900d80580931b1d
Confidential
35
Radio Network Parameters in Flexi Direct
31.4.3
31.4.4
31.4.5
31.4.6
31.4.7
31.4.8
31.4.9
31.4.10
31.5
31.5.1
31.5.2
31.5.3
31.5.4
31.5.5
31.5.6
31.5.7
31.5.8
31.5.9
31.5.10
31.5.11
31.6
31.6.1
31.6.2
31.6.3
31.6.4
36
AMRLCHSRACHPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with HS-RACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1728
AMRLCHSRACHPSPeriodMax (AM RLC status period max for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1729
AMRLCHSRACHPSPeriodMin (AM RLC status period min for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1730
AMRLCHSRACHPSPollPDU (AM RLC period Poll_PDU for PS NRT with
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1731
AMRLCHSRACHPSPollSDU (AM RLC period Poll_SDU for PS NRT with
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1733
AMRLCHSRACHPSPollWin (AM RLC period Poll_Window for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1734
AMRLCHSRACHPSTriggers (AM RLC status report triggers for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1735
HSRACHAMRLCRespHSFACH (AM RLC round trip time with HS-RACH/HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1737
AMRLCMaximumBufferUE (AM RLC maximum buffer allocation for UE) .
1738
AMRLCMaximumBufferUE100 (AM RLC maximum buffer allocation for UE
capability 100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1740
AMRLCMaximumBufferUE1150 (AM RLC maximum buffer allocation for
UE capability 1150). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1740
AMRLCMaximumBufferUE1250 (AM RLC maximum buffer allocation for
UE capability 1250). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1742
AMRLCMaximumBufferUE150 (AM RLC maximum buffer allocation for UE
capability 150) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1743
AMRLCMaximumBufferUE1k (AM RLC maximum buffer allocation for UE
capability 1000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1743
AMRLCMaximumBufferUE200 (AM RLC maximum buffer allocation for UE
capability 200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1745
AMRLCMaximumBufferUE300 (AM RLC maximum buffer allocation for UE
capability 300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1745
AMRLCMaximumBufferUE50 (AM RLC maximum buffer allocation for UE
capability 50). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1747
AMRLCMaximumBufferUE500 (AM RLC maximum buffer allocation for UE
capability 500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1747
AMRLCMaximumBufferUE750 (AM RLC maximum buffer allocation for UE
capability 750) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1749
AMRLCmaximumBufferUE400 (AM RLC maximum buffer allocation for UE
capability 400) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750
AMRLCOnDCHOfNRTPS (AM RLC configuration for PS NRT with DCH).
1751
AMRLCOnDCHOfNRTPSCount (AM RLC status reports count for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1752
AMRLCOnDCHOfNRTPSFilterReTX (AM RLC retransmission filter for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1754
AMRLCOnDCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1755
AMRLCOnDCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1757
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
31.6.5
31.6.6
31.6.7
31.6.8
31.6.9
31.6.10
31.6.11
31.7
31.7.1
31.7.2
31.7.3
31.7.4
31.7.5
31.7.6
31.7.7
31.8
31.8.1
31.8.2
31.8.3
31.8.4
31.8.5
31.8.6
31.8.7
31.9
31.9.1
DN70456011
AMRLCOnDCHOfNRTPSMaxRST (AM RLC MaxRST transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1758
AMRLCOnDCHOfNRTPSPeriodMax (AM RLC status period max for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1759
AMRLCOnDCHOfNRTPSPeriodMin (AM RLC status period min for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1760
AMRLCOnDCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1761
AMRLCOnDCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1763
AMRLCOnDCHOfNRTPSPollWindow (AM RLC period Poll_Window for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1764
AMRLCOnDCHOfNRTPSTriggers (AM RLC status report triggers for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1765
AMRLCOnDCHOfSRB136 (AM RLC configuration for SRB13.6 with DCH)
1767
AMRLCOnDCHOfSRB136MaxDAT (AM RLC MaxDAT transmissions for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1768
AMRLCOnDCHOfSRB136PeriodMax (AM RLC status period max for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1769
AMRLCOnDCHOfSRB136PeriodMin (AM RLC status period min for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1771
AMRLCOnDCHOfSRB136PollPDU (AM RLC period Poll_PDU for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1772
AMRLCOnDCHOfSRB136PollSDU (AM RLC period Poll_SDU for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1773
AMRLCOnDCHOfSRB136PollWindow (AM RLC period Poll_Window for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1774
AMRLCOnDCHOfSRB136Triggers (AM RLC status report triggers for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1775
AMRLCOnDCHOfSRB34 (AM RLC configuration for SRB3.4 with DCH) .
1777
AMRLCOnDCHOfSRB34MaxDAT (AM RLC MaxDAT transmissions for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1778
AMRLCOnDCHOfSRB34PeriodMax (AM RLC status period max for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1779
AMRLCOnDCHOfSRB34PeriodMin (AM RLC status period min for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1781
AMRLCOnDCHOfSRB34PollPDU (AM RLC period Poll_PDU for SRB3.4
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1782
AMRLCOnDCHOfSRB34PollSDU (AM RLC period Poll_SDU for SRB3.4
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1783
AMRLCOnDCHOfSRB34PollWindow (AM RLC period Poll_Window for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1784
AMRLCOnDCHOfSRB34Triggers (AM RLC status report triggers for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1785
AMRLCOnDCHOfStream (AM RLC configuration for PS streaming with
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1787
AMRLCOnDCHOfStreamCount (AM RLC status reports count for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1788
Id:0900d80580931b1d
Confidential
37
Radio Network Parameters in Flexi Direct
31.9.2
31.9.3
31.9.4
31.9.5
31.9.6
31.9.7
31.9.8
31.9.9
31.9.10
31.9.11
31.9.12
31.10
31.10.1
31.10.2
31.10.3
31.10.4
31.10.5
31.10.6
31.10.7
31.10.8
31.10.9
31.10.10
31.11
31.11.1
31.11.2
38
AMRLCOnDCHOfStreamDiscardTime (AM RLC SDU discard time for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1790
AMRLCOnDCHOfStreamFilterReTX (AM RLC retransmission filter for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1791
AMRLCOnDCHOfStreamMaxDAT (AM RLC MaxDAT transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1793
AMRLCOnDCHOfStreamMaxMRW (AM RLC MaxMRW transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1794
AMRLCOnDCHOfStreamMaxRST (AM RLC MaxRST transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1796
AMRLCOnDCHOfStreamPeriodMax (AM RLC status period max for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1797
AMRLCOnDCHOfStreamPeriodMin (AM RLC status period min for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1798
AMRLCOnDCHOfStreamPollPDU (AM RLC period Poll_PDU for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1799
AMRLCOnDCHOfStreamPollSDU (AM RLC period Poll_SDU for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1801
AMRLCOnDCHOfStreamPollWindow (AM RLC period Poll_Window for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1802
AMRLCOnDCHOfStreamTriggers (AM RLC status report triggers for PS
streaming with DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1803
AMRLCOnEDCHOfNRTPS (AM RLC configuration for PS NRT with EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1805
AMRLCOnEDCHOfNRTPSCount (AM RLC status reports count for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1807
AMRLCOnEDCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1808
AMRLCOnEDCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions
for PS NRT with E-DCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1809
AMRLCOnEDCHOfNRTPSMaxRST (AM RLC maxRST transmissions for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1810
AMRLCOnEDCHOfNRTPSPeriodMax (AM RLC status period max for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1811
AMRLCOnEDCHOfNRTPSPeriodMin (AM RLC status period min for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1813
AMRLCOnEDCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1814
AMRLCOnEDCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1815
AMRLCOnEDCHOfNRTPSPollWindow (AM RLC period Poll_Window for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1816
AMRLCOnEDCHOfNRTPSTriggers (AM RLC status report triggers for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1817
AMRLCOnEDCHOfStrPS (AM RLC configuration for PS streaming with EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1819
EDCHStrPSCount (AM RLC status reports count for PS streaming E-DCH)
1821
EDCHStrPSDiscardTime (AM RLC SDU discard time for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1822
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
31.11.3
31.11.4
31.11.5
31.11.6
31.11.7
31.11.8
31.11.9
31.11.10
31.11.11
31.12
31.12.1
31.12.2
31.12.3
31.12.4
31.12.5
31.12.6
31.12.7
31.12.8
31.12.9
31.13
31.13.1
31.13.2
31.13.3
31.13.4
31.13.5
DN70456011
EDCHStrPSMaxDAT (AM RLC MaxDAT transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1824
EDCHStrPSMaxMRW (AM RLC MaxMRW transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1825
EDCHStrPSMaxRST (AM RLC maxRST transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1826
EDCHStrPSPeriodMax (AM RLC status period max for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1827
EDCHStrPSPeriodMin (AM RLC status period min for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1828
EDCHStrPSPollPDU (AM RLC period Poll_PDU for PS streaming E-DCH)
1829
EDCHStrPSPollSDU (AM RLC period Poll_SDU for PS streaming E-DCH)
1830
EDCHStrPSPollWindow (AM RLC period Poll_Window for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1831
EDCHStrPSTriggers (AM RLC status report triggers for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1832
AMRLCOnFACHOfPS (AM RLC configuration for PS NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1834
AMRLCOnFACHOfPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1836
AMRLCOnFACHOfPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1837
AMRLCOnFACHOfPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with FACH/RAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1838
AMRLCOnFACHOfPSPeriodMax (AM RLC status period max for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1839
AMRLCOnFACHOfPSPeriodMin (AM RLC status period min for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1840
AMRLCOnFACHOfPSPollPDU (AM RLC period Poll_PDU for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1841
AMRLCOnFACHOfPSPollSDU (AM RLC period Poll_SDU for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1842
AMRLCOnFACHOfPSPollWindow (AM RLC period Poll_Window for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1843
AMRLCOnFACHOfPSTriggers (AM RLC status report triggers for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1845
AMRLCOnFACHOfSRB (AM RLC configuration for SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1847
AMRLCOnFACHOfSRBMaxDAT (AM RLC MaxDAT transmissions for
SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1848
AMRLCOnFACHOfSRBPeriodMax (AM RLC status period max for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1849
AMRLCOnFACHOfSRBPeriodMin (AM RLC status period min for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1851
AMRLCOnFACHOfSRBPollPDU (AM RLC period Poll_PDU for SRB with
FACH/RACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1852
AMRLCOnFACHOfSRBPollSDU (AM RLC period Poll_SDU for SRB with
FACH/RACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1853
Id:0900d80580931b1d
Confidential
39
Radio Network Parameters in Flexi Direct
31.13.6
31.13.7
31.14
31.14.1
31.14.2
31.14.3
31.14.4
31.14.5
31.14.6
31.14.7
31.14.8
31.14.9
31.14.10
31.14.11
31.15
31.15.1
31.15.2
31.15.3
31.15.4
31.15.5
31.15.6
31.15.7
31.15.8
31.15.9
31.15.10
40
AMRLCOnFACHOfSRBPollWindow (AM RLC period Poll_Window for
SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1854
AMRLCOnFACHOfSRBTriggers (AM RLC status report triggers for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1855
AMRLCOnHSDSCHOfNRTPS (AM RLC configuration for PS NRT with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1857
AMRLCOnHSDSCHOfNRTPSCount (AM RLC status reports count for PS
NRT with HS-DSCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1858
AMRLCOnHSDSCHOfNRTPSFilterReTX (AM RLC retransmission filter
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1860
AMRLCOnHSDSCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1861
AMRLCOnHSDSCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1862
AMRLCOnHSDSCHOfNRTPSMaxRST (AM RLC maxRST transmissions
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1863
AMRLCOnHSDSCHOfNRTPSPeriodMax (AM RLC status period max for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1864
AMRLCOnHSDSCHOfNRTPSPeriodMin (AM RLC status period min for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1866
AMRLCOnHSDSCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS
NRT with HS-DSCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1867
AMRLCOnHSDSCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS
NRT with HS-DSCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1868
AMRLCOnHSDSCHOfNRTPSPollWindow (AM RLC period Poll_Window
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1869
AMRLCOnHSDSCHOfNRTPSTriggers (AM RLC status report triggers for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1870
AMRLCOnHSDSCHOfStrPS (AM RLC configuration for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1872
HSDSCHStrDiscardTime (AM RLC SDU discard time for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1874
HSDSCHStrPSCount (AM RLC status reports count for PS stream with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1875
HSDSCHStrPSFilterReTX (AM RLC retransmission filter for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1877
HSDSCHStrPSMaxDAT (AM RLC MaxDAT transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1878
HSDSCHStrPSMaxMRW (AM RLC MaxMRW transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1879
HSDSCHStrPSMaxRST (AM RLC maxRST transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1880
HSDSCHStrPSPeriodMax (AM RLC status period max for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1881
HSDSCHStrPSPeriodMin (AM RLC status period min for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1882
HSDSCHStrPSPollPDU (AM RLC period Poll_PDU for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1883
HSDSCHStrPSPollSDU (AM RLC period Poll_SDU for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1885
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
31.15.11
31.15.12
31.16
31.17
31.17.1
31.17.2
31.17.3
31.17.4
31.17.5
31.17.6
31.17.7
31.17.8
31.17.9
31.17.10
31.17.11
31.17.12
31.17.13
31.17.14
31.17.15
31.17.16
31.18
31.18.1
31.18.2
31.18.3
31.18.4
31.18.5
DN70456011
HSDSCHStrPSPollWindow (AM RLC period Poll_Window for PS streaming with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1886
HSDSCHStrPSTriggers (AM RLC status report triggers for PS str with HSDSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1887
AMRLCPeriodMaxHSSRB (AM RLC status period max for SRBs with HSRACH/HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1889
AMRLCRelatTXWindow (AM RLC relative transmission window sizes) . .
1891
AMRLCRelatTXWindowRate1 (AM RLC relative Tx window size defining
data rate 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1892
AMRLCRelatTXWindowRate1Size (AM RLC relative Tx window size assigned to data rate 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1893
AMRLCRelatTXWindowRate2 (AM RLC relative Tx window size defining
data rate 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1894
AMRLCRelatTXWindowRate2Size (AM RLC relative Tx window size assigned to data rate 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1895
AMRLCRelatTXWindowRate3 (AM RLC relative Tx window size defining
data rate 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1896
AMRLCRelatTXWindowRate3Size (AM RLC relative Tx window size assigned to data rate 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1897
AMRLCRelatTXWindowRate4 (AM RLC relative Tx window size defining
data rate 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1898
AMRLCRelatTXWindowRate4Size (AM RLC relative Tx window size assigned to data rate 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1899
AMRLCRelatTXWindowRate5 (AM RLC relative Tx window size defining
data rate 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900
AMRLCRelatTXWindowRate5Size (AM RLC relative Tx window size assigned to data rate 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1901
AMRLCRelatTXWindowRate6 (AM RLC relative Tx window size defining
data rate 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1902
AMRLCRelatTXWindowRate6Size (AM RLC relative Tx window size assigned to data rate 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1903
AMRLCRelatTXWindowRate7 (AM RLC relative Tx window size defining
data rate 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1904
AMRLCRelatTXWindowRate7Size (AM RLC relative Tx window size assigned to data rate 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1905
AMRLCRelatTXWindowRate8 (AM RLC relative Tx window size defining
data rate 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1906
AMRLCRelatTXWindowRate8Size (AM RLC relative Tx window size assigned to data rate 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1907
AMRLCRespTimeDCH (AM RLC round trip times with DCH) . . . . . . 1908
AMRLCRespTimeDCH10 (AM RLC round trip time with DCH/DCH of TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1909
AMRLCRespTimeDCH20 (AM RLC round trip time with DCH/DCH of TTI
20 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1910
AMRLCRespTimeDCH40 (AM RLC round trip time with DCH/DCH of TTI
40 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1911
AMRLCRespTimeDCHRevHSDSCH (AM RLC round trip time for
DCH/HS-DSCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1912
AMRLCRespTimeRevEDCH (AM RLC round trip time for E-DCH/DCH) .
1913
Id:0900d80580931b1d
Confidential
41
Radio Network Parameters in Flexi Direct
31.19
31.20
31.21
31.21.1
31.21.2
31.22
31.23
31.24
31.25
31.25.1
31.25.2
31.25.3
31.25.4
31.25.5
31.25.6
31.25.7
31.25.8
31.26
31.26.1
31.26.2
31.26.3
31.27
31.28
31.29
31.30
31.31
31.32
42
AMRLCRespTimeEDCH (AM RLC round trip time with E-DCH) . . . . 1914
AMRLCRespTimeFACHAndRACH (AM RLC round trip time with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1915
AMRLCRespTimeHSDSCH (AM RLC round trip times with HS-DSCH) . .
1916
AMRLCRespTimeHSDSCHRevDCH (AM RLC round trip time with HSDSCH/DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1917
AMRLCRespTimeHSDSCHRevEDCH (AM RLC round trip time with HSDSCH/E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1918
AMRLCRespTimeHSSRB (AM RLC round trip time for SRBs with HS-RACH/HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1919
AMRLCSRB3n4PeriodMax (AM RLC status period max for SRB3 and
SRB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1920
AMRLCSRB3n4RespTime (AM RLC round trip time for SRB3 and SRB4)
1921
AMRLCSRBHSPA (AM RLC configuration for SRB on HSPA) . . . . . 1922
AMRLCRespTimeSRBHSPA (AM RLC round trip time for SRB on HSPA)
1923
AMRLCSRBHSPAMaxDAT (AM RLC MaxDAT transmissions for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1924
AMRLCSRBHSPAPeriodMax (AM RLC status period max for SRB on HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1925
AMRLCSRBHSPAPeriodMin (AM RLC status period min for SRB on HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1927
AMRLCSRBHSPAPollPDU (AM RLC period Poll_PDU for SRB on HSPA)
1928
AMRLCSRBHSPAPollSDU (AM RLC period Poll_SDU for SRB on HSPA)
1929
AMRLCSRBHSPAPollWindow (AM RLC period Poll_Window for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1930
AMRLCSRBHSPATriggers (AM RLC status report triggers for SRB on HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1931
AMRLCTXWindowSizeSRB (AM RLC transmission window sizes for SRBs
2, 3 and 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1933
AMRLCTXWindowSizeSRB2 (AM RLC transmission window size for SRB
2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1934
AMRLCTXWindowSizeSRB3 (AM RLC transmission window size for SRB
3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1935
AMRLCTXWindowSizeSRB4 (AM RLC transmission window size for SRB
4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1937
PDUSizeBitRateThr (Bit rate threshold for RLC PDU size 656 with HSDSCH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1938
PDUSizeCodeThreshold (Number of HS-PDSCH codes for greater RLC
PDU size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1939
PDUSizeSIRThr (SIR threshold for RLC PDU size 656 with HS-DSCH) . .
1941
RLCConfOptionFPS (RLC Conf option switch for Fast Cell_PCH Switching) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1942
RNRLCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 1944
RNRLCId (RNRLC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1945
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
31.33
31.34
31.35
32
32.1
32.1.1
32.1.2
32.1.3
32.1.4
32.2
32.2.1
32.2.2
32.2.3
32.2.4
32.2.5
32.2.6
32.3
32.3.1
32.3.2
32.3.3
32.3.4
32.3.5
32.3.6
32.4
32.4.1
32.4.2
32.4.3
32.4.4
32.4.5
32.4.6
32.4.7
32.5
32.5.1
32.5.2
32.5.3
32.5.4
32.5.5
32.5.6
32.6
DN70456011
SDUdiscardModeRTPS (SDU discard mode for RT PS RAB employing
RLC AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1946
UMRLCEVoiceDiscardTime (UM RLC SDU discard time in UE for CS voice
over HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1947
UMRLCPTTDiscardTime (UM RLC SDU discard time in UE for PTT) 1948
RNTRM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1950
ActivityFactorForAMRDCHTrafficBearers (Activity factor for AMR DCH
traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1950
Af122AMRDL (Activity factor for 12.2 / 12.65 AMR DCH DL bearer) 1951
Af122AMRUL (Activity factor for 12.2 / 12.65 AMR DCH UL bearer) 1951
Af59AMRDL (Activity factor for 5.9 AMR DCH DL bearer) . . . . . . . . 1952
Af59AMRUL (Activity factor for 5.9 AMR DCH UL bearer) . . . . . . . . 1953
ActivityFactorForCSDCHTrafficBearers (Activity factor for CS DCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1954
Af144CSStreDL (Activity factor for 14.4 CS streaming DL bearer) . . 1955
Af144CSStreUL (Activity factor for 14.4 CS streaming UL bearer) . . 1956
Af576CSStreDL (Activity factor for 57.6 CS streaming DL bearer) . . 1957
Af576CSStreUL (Activity factor for 57.6 CS streaming UL bearer) . . 1958
Af64CSConDL (Activity factor for 64 CS conversational DL bearer) . 1959
Af64CSConUL (Activity factor for 64 CS conversational UL bearer) . 1960
ActivityFactorForDCCHTrafficBearers (Activity factor for DCCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1961
Af128And136DCCHDL (Activity factor for 12.8/13.6 DCCH DL bearer) . .
1962
Af128And136DCCHUL (Activity factor for 12.8/13.6 DCCH UL bearer) . .
1963
Af16And17DCCHDL (Activity factor for 1.6/1.7 DCCH DL bearer) . . 1964
Af16And17DCCHUL (Activity factor for 1.6/1.7 DCCH UL bearer) . . 1965
Af32And34DCCHDL (Activity factor for 3.2/3.4 DCCH DL bearer) . . 1966
Af32And34DCCHUL (Activity factor for 3.2/3.4 DCCH UL bearer) . . 1967
ActivityFactorForFACHRACHTrafficBearers (Activity factor for FACH and
RACH traffic bearers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1968
AfFACHCCDL (Activity factor for FACH-C/C DL bearer). . . . . . . . . . 1969
AfFACHCIDL (Activity factor for FACH-C/I DL bearer) . . . . . . . . . . . 1970
AfFACHContUL (Activity factor for FACH control UL bearer) . . . . . . 1971
AfFACHSDL (Activity factor for FACH-S DL bearer) . . . . . . . . . . . . . 1972
AfFACHUDL (Activity factor for FACH-U DL bearer) . . . . . . . . . . . . . 1973
AfRACH208UL (Activity factor for RACH 20.8 UL bearer). . . . . . . . . 1974
AfRACHContDL (Activity factor for RACH control DL bearer) . . . . . . 1975
ActivityFactorForHSPA (Activity factor for HSPA bearers) . . . . . . . . 1976
AfPTTDL (Activity Factor for PTT RAB in Downlink) . . . . . . . . . . . . . 1977
AfPTTUL (Activity Factor for PTT RAB in Uplink) . . . . . . . . . . . . . . . 1978
AfRTHSDPA (Activity factor for RT HSDPA bearer) . . . . . . . . . . . . . 1979
AfRTHSUPA (Activity factor for RT HSUPA bearer) . . . . . . . . . . . . . 1980
AfSRBOnHSDPA (Activity factor for SRB on HSDPA bearer). . . . . . 1981
AfSRBOnHSUPA (Activity factor for SRB on HSUPA bearer). . . . . . 1982
ActivityFactorForNRTDCHTrafficBearers (Activity factor for NRT DCH traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1983
Id:0900d80580931b1d
Confidential
43
Radio Network Parameters in Flexi Direct
32.6.1
32.6.2
32.6.3
32.6.4
32.6.5
32.6.6
32.6.7
32.6.8
32.6.9
32.6.10
32.6.11
32.6.12
32.6.13
32.6.14
32.7
32.7.1
32.7.2
32.8
32.8.1
32.8.2
32.8.3
32.8.4
32.8.5
32.8.6
32.8.7
32.8.8
32.8.9
32.8.10
32.8.11
32.8.12
32.8.13
32.8.14
32.8.15
32.8.16
32.8.17
32.8.18
32.8.19
32.8.20
32.8.21
32.8.22
32.9
32.10
32.11
32.12
32.13
44
Af128NRTDCHDL (Activity factor for 128 NRT DCH DL bearer) . . . . 1985
Af128NRTDCHUL (Activity factor for 128 NRT DCH UL bearer) . . . . 1985
Af16NRTDCHDL (Activity factor for 16 NRT DCH DL bearer) . . . . . . 1986
Af16NRTDCHUL (Activity factor for 16 NRT DCH UL bearer) . . . . . . 1987
Af256NRTDCHDL (Activity factor for 256 NRT DCH DL bearer) . . . . 1988
Af256NRTDCHUL (Activity factor for 256 NRT DCH UL bearer) . . . . 1989
Af32NRTDCHDL (Activity factor for 32 NRT DCH DL bearer) . . . . . . 1990
Af32NRTDCHUL (Activity factor for 32 NRT DCH UL bearer) . . . . . . 1991
Af384NRTDCHDL (Activity factor for 384 NRT DCH DL bearer) . . . . 1992
Af384NRTDCHUL (Activity factor for 384 NRT DCH UL bearer) . . . . 1993
Af64NRTDCHDL (Activity factor for 64 NRT DCH DL bearer) . . . . . . 1994
Af64NRTDCHUL (Activity factor for 64 NRT DCH UL bearer) . . . . . . 1995
Af8NRTDCHDL (Activity factor for 8 NRT DCH DL bearer) . . . . . . . . 1996
Af8NRTDCHUL (Activity factor for 8 NRT DCH UL bearer) . . . . . . . . 1997
ActivityFactorForPCHTrafficBearers (Activity factor for PCH traffic bearers)
1998
AfPCHContUL (Activity factor for PCH control UL bearer) . . . . . . . . . 1999
AfPCHDL (Activity factor for PCH DL bearer). . . . . . . . . . . . . . . . . . . 2000
ActivityFactorForRTPSTrafficBearers (Activity factor for RT PS traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2001
Af128RTPSAMDL (Activity factor for 128 RT PS AM DL bearer) . . . . 2002
Af128RTPSAMUL (Activity factor for 128 RT PS AM UL bearer) . . . . 2003
Af128RTPSUMDL (Activity factor for 128 RT PS UM DL bearer). . . . 2004
Af128RTPSUMUL (Activity factor for 128 RT PS UM UL bearer). . . . 2005
Af16RTPSAMDL (Activity factor for 16 RT PS AM DL bearer) . . . . . . 2006
Af16RTPSAMUL (Activity factor for 16 RT PS AM UL bearer) . . . . . . 2007
Af16RTPSUMDL (Activity factor for 16 RT PS UM DL bearer). . . . . . 2008
Af16RTPSUMUL (Activity factor for 16 RT PS UM UL bearer). . . . . . 2009
Af256RTPSAMDL (Activity factor for 256 RT PS AM DL bearer) . . . . 2010
Af256RTPSUMDL (Activity factor for 256 RT PS UM DL bearer). . . . 2011
Af32RTPSAMDL (Activity factor for 32 RT PS AM DL bearer) . . . . . . 2012
Af32RTPSAMUL (Activity factor for 32 RT PS AM UL bearer) . . . . . . 2013
Af32RTPSUMDL (Activity factor for 32 RT PS UM DL bearer). . . . . . 2014
Af32RTPSUMUL (Activity factor for 32 RT PS UM UL bearer). . . . . . 2015
Af64RTPSAMDL (Activity factor for 64 RT PS AM DL bearer) . . . . . . 2016
Af64RTPSAMUL (Activity factor for 64 RT PS AM UL bearer) . . . . . . 2017
Af64RTPSUMDL (Activity factor for 64 RT PS UM DL bearer). . . . . . 2018
Af64RTPSUMUL (Activity factor for 64 RT PS UM UL bearer). . . . . . 2019
Af8RTPSAMDL (Activity factor for 8 RT PS AM DL bearer) . . . . . . . . 2020
Af8RTPSAMUL (Activity factor for 8 RT PS AM UL bearer) . . . . . . . . 2021
Af8RTPSUMDL (Activity factor for 8 RT PS UM DL bearer). . . . . . . . 2022
Af8RTPSUMUL (Activity factor for 8 RT PS UM UL bearer). . . . . . . . 2023
DSCPBTSOMToOMS (DSCP for BTS OM towards OMS). . . . . . . . . 2024
DSCPForGTPSignalling (DSCP for GTP signalling). . . . . . . . . . . . . . 2025
EchoRequestSending (Echo Request Sending) . . . . . . . . . . . . . . . . . 2026
IPStackErrorTimer (IP Stack Error timer) . . . . . . . . . . . . . . . . . . . . . . 2027
N3Requests (N3-REQUESTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2028
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
32.14
32.15
32.16
RNTRMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 2029
RNTRMId (RNTRM Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2030
T3Response (T3-RESPONSE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2031
33
33.1
VBTS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2033
DediMeasRepPeriodCSdata (Dedicated Measurement Reporting Period
CS data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2033
DediMeasRepPeriodPSdata (Dedicated Measurement Reporting Period
PS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2034
DedicatedMeasReportPeriod (Dedicated Measurement Reporting Period)
2035
HARQRVConfiguration (HARQ RV Configuration) . . . . . . . . . . . . . . 2036
MeasFiltCoeff (Measurement filter coefficient) . . . . . . . . . . . . . . . . . 2037
NodeBRABReconfigSupport (NodeB PS RAB reconfiguration Support). .
2038
VBTSChangeOrigin (Change Origin). . . . . . . . . . . . . . . . . . . . . . . . . 2039
VBTSId (VBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2041
33.2
33.3
33.4
33.5
33.6
33.7
33.8
34
34.1
34.2
34.3
34.4
34.5
34.6
34.7
34.8
34.9
34.10
34.11
34.12
34.13
34.14
34.15
34.16
34.17
34.18
34.19
34.20
34.21
34.22
34.23
34.24
34.25
34.26
DN70456011
VCEL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2042
CSAMRModeSET (Configured CS AMR mode sets) . . . . . . . . . . . . 2042
CSAMRModeSETWB (Configured CS WAMR mode sets) . . . . . . . . 2043
DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . 2045
EDCHMinimumSetETFCI (E-DCH minimum set E-TFCI) . . . . . . . . . 2046
EbNoSetIdentifier (Eb/No parameter set identifier) . . . . . . . . . . . . . . 2046
FastActOfTargetServCell (Faster Activation Of Target Serving Cell) 2047
FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . 2049
HHoMaxAllowedBitrateDL (Maximum allowed DL user bit rate in HHO). .
2050
HHoMaxAllowedBitrateUL (Maximum allowed UL user bit rate in HHO). .
2051
HSDPAFmcgIdentifier (HSDPA FMCG identifier) . . . . . . . . . . . . . . . 2052
HSDPAFmciIdentifier (HSDPA FMCI identifier). . . . . . . . . . . . . . . . . 2053
HSDPAFmcsIdentifier (HSDPA FMCS identifier) . . . . . . . . . . . . . . . 2054
HSDPAHopsIdentifier (HSDPA HOPS identifier). . . . . . . . . . . . . . . . 2055
HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2056
HSPAFmcsIdentifier (HSPA FMCS identifier) . . . . . . . . . . . . . . . . . . 2057
HSPASCCSpecificATO (HSPA SCC Specific ATO Value) . . . . . . . . 2058
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay). 2059
HSUPAEnabled (HSUPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2061
InitialBitRateDL (Initial bit rate in downlink) . . . . . . . . . . . . . . . . . . . . 2062
InitialBitRateUL (Initial bit rate in uplink) . . . . . . . . . . . . . . . . . . . . . . 2063
LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2065
MaxBitRateDLPSNRT (Maximum downlink bit rate for PS domain NRT data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2066
MaxBitRateULPSNRT (Maximum uplink bit rate for PS domain NRT data)
2068
MaxTotalUplinkSymbolRate (Maximum total uplink symbol rate) . . . 2069
MinAllowedBitRateDL (Minimum allowed bit rate in downlink) . . . . . 2071
MinAllowedBitRateUL (Minimum allowed bit rate in uplink). . . . . . . . 2072
Id:0900d80580931b1d
Confidential
45
Radio Network Parameters in Flexi Direct
34.27
34.28
34.29
34.30
34.31
34.32
34.33
34.34
34.35
34.36
34.37
34.38
34.39
34.40
34.41
34.42
34.43
34.44
34.45
34.46
34.47
34.48
34.49
34.50
34.51
34.52
34.53
35
35.1
35.2
35.3
35.4
35.5
35.6
35.7
46
NrtFmcgIdentifier (NRT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . 2074
NrtFmciIdentifier (NRT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2075
NrtFmcsIdentifier (NRT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . 2076
NrtHopgIdentifier (NRT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . 2076
NrtHopiIdentifier (NRT HOPI Identifier). . . . . . . . . . . . . . . . . . . . . . . . 2077
NrtHopsIdentifier (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . 2078
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2079
PtxOffsetHSSCCH (The power offset of the HS-SCCH) . . . . . . . . . . 2081
RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2081
RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for AMR multi-service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2083
RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for AMR multi-service)
2084
RTwithHSDPAFmciIdentifier (HSDPA FMCI identifier for AMR multi-service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2085
RTwithHSDPAFmcsIdentifier (HSDPA FMCS identifier for AMR multi-service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2086
RTwithHSDPAHopsIdentifier (HSDPA HOPS identifier for AMR multi-service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2087
RelocComm_in_InterRNC_HHO (Usage of Relocation Commit procedure
in inter RNC HHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2088
RtFmcgIdentifier (RT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2089
RtFmciIdentifier (RT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 2089
RtFmcsIdentifier (RT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2090
RtHopgIdentifier (RT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2091
RtHopiIdentifier (RT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 2092
RtHopsIdentifier (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2093
RxDivIndicator (Rx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . 2094
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . . 2095
SRBHopsIdentifier (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . 2096
VCELChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . . 2097
VCELId (VCEL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2098
WACSetIdentifier (WAC Parameter Set Identifier) . . . . . . . . . . . . . . . 2099
WAC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2100
DCHUtilRelAveWin (Window size for the release throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2100
DCHUtilRelThrDL (Threshold for the downlink DCH release measurement)
2101
DCHUtilRelThrUL (Threshold for the uplink DCH release measurement) .
2103
DCHUtilRelTimeToTrigger (Time to trigger for the release throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2105
EDCHMACdFlowThroughputAveWin (Window size of E-DCH MAC-d flow
throughput measurement). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2106
EDCHMACdFlowThroughputRelThr (Low throughput threshold of the EDCH MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2107
EDCHMACdFlowThroughputTimetoTrigger (Low throughput time to trigger
of the E-DCH MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2108
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
35.8
35.9
35.10
35.11
35.12
35.13
35.14
35.15
35.16
35.17
35.18
35.18.1
35.18.2
35.18.3
35.18.4
35.18.5
35.18.6
35.18.7
35.18.8
35.19
35.19.1
35.19.2
35.19.3
35.19.4
35.19.5
35.19.6
35.19.7
35.19.8
DN70456011
HSDPAInitialBRULStrNRT (Initial bitrate for HSDPA UL DCH for NRT with
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2109
HSDPAMaxBitrateUL (Maximum bit rate for HSDPA UL DCH return channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2110
HSDPAMinBRULStrNRT (Min bitrate for HSDPA UL DCH for NRT with
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2112
HSDPAinitialBitrateUL (Initial bitrate for HSDPA associated UL DCH) . . .
2113
HSDPAminAllowedBitrateUL (Minimum bitrate for HSDPA associated UL
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2114
InactCPCBatOptT (Inactive CPC user with battery optimization timer) . . .
2116
InactCPCNoBatOptT (Inactive CPC user without battery optimization timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2119
InactHSRACH (Inactive HS-RACH capable UE) . . . . . . . . . . . . . . . . 2123
InactNonCPCBatOptT (Inactive nonCPC user with battery optimization
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2125
InactNonCPCNoBatOptT (Inactive nonCPC user without battery optimization timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2128
InactivityTimerDownlinkDCH (Inactivity timer for downlink DCH) . . . 2132
InactivityTimerDownlinkDCH128 (Inactivity timer for downlink 128kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2133
InactivityTimerDownlinkDCH16 (Inactivity timer for downlink 16kbps DCH)
2134
InactivityTimerDownlinkDCH256 (Inactivity timer for downlink 256kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2135
InactivityTimerDownlinkDCH32 (Inactivity timer for downlink 32kbps DCH)
2136
InactivityTimerDownlinkDCH320 (Inactivity timer for downlink 320kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2137
InactivityTimerDownlinkDCH384 (Inactivity timer for downlink 384kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2138
InactivityTimerDownlinkDCH64 (Inactivity timer for downlink 64kbps DCH)
2139
InactivityTimerDownlinkDCH8 (Inactivity timer for downlink 8kbps DCH) .
2140
InactivityTimerUplinkDCH (Inactivity timer for uplink DCH) . . . . . . . . 2141
InactivityTimerUplinkDCH128 (Inactivity timer for uplink 128kbps DCH). .
2143
InactivityTimerUplinkDCH16 (Inactivity timer for uplink 16kbps DCH) 2143
InactivityTimerUplinkDCH256 (Inactivity timer for uplink 256kbps DCH). .
2144
InactivityTimerUplinkDCH32 (Inactivity timer for uplink 32kbps DCH) 2145
InactivityTimerUplinkDCH320 (Inactivity timer for uplink 320kbps DCH). .
2146
InactivityTimerUplinkDCH384 (Inactivity timer for uplink 384kbps DCH). .
2147
InactivityTimerUplinkDCH64 (Inactivity timer for uplink 64kbps DCH) 2148
InactivityTimerUplinkDCH8 (Inactivity timer for uplink 8kbps DCH). . 2149
Id:0900d80580931b1d
Confidential
47
Radio Network Parameters in Flexi Direct
35.20
35.21
35.22
35.23
35.24
35.25
35.26
35.27
35.28
35.29
35.30
35.31
35.31.1
35.31.2
35.31.3
35.31.4
35.31.5
35.31.6
35.31.7
35.31.8
35.31.9
35.31.10
35.31.11
35.31.12
36
36.1
36.2
36.2.1
36.2.2
36.2.3
48
MACdflowthroughputAveWin (Window size of the MAC-d flow throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2150
MACdflowutilRelThr (Low utilisation threshold of the MAC-d flow) . . . 2151
MACdflowutilTimetoTrigger (Low utilization time to trigger of the MAC-d
flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2152
MSActivitySupervision (Time supervision of user inactivity (for NRT RBs))
2154
PrxNoiseMaxTuneAbsolute (Absolute limit in uplink noise autotuning) . . .
2155
TrafVolPendingTimeDL (Downlink traffic volume measurement pending
time after trigger). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2156
TrafVolPendingTimeUL (Uplink traffic volume measurement pending time
after trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2158
TrafVolThresholdULLow (Uplink traffic volume measurement low threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2159
UL_DL_activation_timer (UL/DL activation timer) . . . . . . . . . . . . . . . . 2161
WACChangeOrigin (WAC Change origin) . . . . . . . . . . . . . . . . . . . . . 2162
WACId (WAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2163
WaitTimeRRC (Wait time in RRC connection request rejection) . . . . 2164
WaitTimeRRCbackground (RRC wait time for background causes) 2166
WaitTimeRRCconversational (RRC wait time for conversational causes)
2167
WaitTimeRRCemergency (RRC wait time for emergency causes) . 2168
WaitTimeRRChighPrioritySignalling (RRC wait time for high priority signalling causes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2169
WaitTimeRRCinterRATreselection (RRC wait time for inter-RAT re-selection causes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2170
WaitTimeRRCinteractive (RRC wait time for interactive causes) . . . 2171
WaitTimeRRClowPrioritySignalling (RRC wait time for low priority signalling causes). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2172
WaitTimeRRCother (RRC wait time for other causes). . . . . . . . . . . . 2173
WaitTimeRRCregistration (RRC wait time for registration causes) . 2174
WaitTimeRRCstreaming (RRC wait time for streaming causes) . . . 2175
WaitTimeRRCsubscribed (RRC wait time for subscribed causes) . . 2176
WaitTimeRRCunknown (RRC wait time for unknown causes) . . . . . 2176
36.2.4
36.3
36.4
WANE Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2178
AuthorisedNetworkId (Authorised Network Identifier) . . . . . . . . . . . . . 2178
AuthorisedNetworkPLMN (Authorised Network PLMN) . . . . . . . . . . . 2178
AuthorisedNetworkMCC (Authorised Network Mobile Country Code) 2179
AuthorisedNetworkMNC (Authorised Network Mobile Network Code) 2180
AuthorisedNetworkMNClength (Authorised Network Mobile Network Code
Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2181
Technology (Technology used in the Authorised Network) . . . . . . . . 2182
WANEChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 2183
WANEName (WANE Name). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2184
37
37.1
37.2
WBTS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2186
AdminWBTSState (Admin WBTS State). . . . . . . . . . . . . . . . . . . . . . . 2186
BTSAdditionalInfo (BTS Additional Information) . . . . . . . . . . . . . . . . . 2186
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
37.3
37.4
37.5
37.6
37.7
37.8
37.9
37.10
37.11
37.12
37.13
37.14
37.15
37.16
37.17
37.18
37.19
37.20
37.21
37.22
37.23
37.24
37.25
37.26
37.27
37.28
37.29
37.30
37.31
37.32
37.33
37.34
37.35
37.36
37.37
37.38
DN70456011
BTSIPAddress (BTS O&M IP address) . . . . . . . . . . . . . . . . . . . . . . . 2187
BTSSupportForHSPACM (BTS Support For HSPA CM). . . . . . . . . . 2188
BlindHOIntraBTSQCheck (Blind HO Intra BTS Quality Check) . . . . . 2189
BroadcastSIB15 (Broadcast SIB15). . . . . . . . . . . . . . . . . . . . . . . . . . 2190
BroadcastSIB15_2 (Broadcast SIB15.2) . . . . . . . . . . . . . . . . . . . . . . 2192
BroadcastSIB15_3 (Broadcast SIB15.3) . . . . . . . . . . . . . . . . . . . . . . 2193
DCNLinkStatus (O&M DCN link status) . . . . . . . . . . . . . . . . . . . . . . . 2194
DCNSecurityStatus (O&M DCN secure link status). . . . . . . . . . . . . . 2194
DLORLAveragingWindowSize (Tx power of radio link averaging window
size for DLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2195
DediMeasRepPeriodCSdata (Dedicated Measurement Reporting Period
CS data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2197
DediMeasRepPeriodPSdata (Dedicated Measurement Reporting Period
PS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2198
DedicatedMeasReportPeriod (Dedicated Measurement Reporting Period)
2199
DelayThresholdMax (Maximum Threshold for HSUPA congestion handling
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200
DelayThresholdMax2msTTI (Maximum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2201
DelayThresholdMid (Middle Threshold value for HSUPA congestion delay)
2202
DelayThresholdMid2msTTI (Middle Threshold for HSUPA congestion delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2203
DelayThresholdMin (Minimum Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2204
DelayThresholdMin2msTTI (Minimum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2205
HARQRVConfiguration (HARQ RV Configuration) . . . . . . . . . . . . . . 2206
HSDPA14MbpsPerUser (HSDPA14MbpsPerUser). . . . . . . . . . . . . . 2207
HSDPACCEnabled (HSDPA Congestion Control activation) . . . . . . 2208
HSUPAXUsersEnabled (HSUPA x users enabled) . . . . . . . . . . . . . . 2209
IPNBId (IPNB object identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2212
InactCACThresholdATM (Inactive users CAC Threshold for ATM) . . 2213
InactCACThresholdIP (Inactive users CAC Threshold for IP) . . . . . . 2214
InactUsersCIDThreshold (Inactive users Connection ID Threshold) . 2215
IntelligentSDPrioHO (Priorized Handover Type in Intelligent Shutdown) .
2216
LoadControlPeriodPS (PS load control period) . . . . . . . . . . . . . . . . . 2217
MaxBTSOMFrameSize (Maximum BTS OM frame size). . . . . . . . . . 2217
MaxFPDLFrameSizeIub (Maximum FP downlink frame size Iub) . . . 2218
MaxNumberEDCHLCG (Maximum number of E-DCHs in the local cell
group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2220
MeasFiltCoeff (Measurement filter coefficient) . . . . . . . . . . . . . . . . . 2221
MinUDPPortIub (Minimum UDP port value for the Iub) . . . . . . . . . . . 2222
NBAPCommMode (NBAP Communication Mode) . . . . . . . . . . . . . . 2223
NESWVersion (NE-SW-Version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2224
NEType (NE-type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2225
Id:0900d80580931b1d
Confidential
49
Radio Network Parameters in Flexi Direct
37.39
37.40
37.41
37.42
37.43
37.44
37.45
37.46
37.47
37.48
37.49
37.50
37.51
37.52
37.53
37.54
37.55
37.56
37.57
37.58
37.59
37.60
37.61
37.62
37.63
37.64
37.65
37.66
50
NodeBRABReconfigSupport (NodeB PS RAB reconfiguration Support) . .
2227
PDUSize656WithHSDSCH (Usage of RLC PDU size 656 with HS-DSCH)
2228
PSAveragingWindowSize (Load measurement averaging window size for
packet scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2229
PSRLAveragingWindowSize (Tx power of radio link averaging window size
for PS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2230
PWSMAVTrafficVERLogic (Traffic verification logic in PWSM cell activation process) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2231
PWSMEnableWakeUpTime (Enable cell activation based on time of day)
2233
PWSMInUse (The PWSM usage in BTS) . . . . . . . . . . . . . . . . . . . . . . 2234
PWSMRemCellSDBeginHour (PWSM Shutdown Time Begin Hour for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2236
PWSMRemCellSDBeginMin (PWSM Shutdown Time Begin Minute for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2237
PWSMRemCellSDEndHour (PWSM Shutdown Time End Hour for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2238
PWSMRemCellSDEndMin (PWSM Shutdown Time End Minute for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2239
PWSMShutdownBeginHour (Hour when the cell shutdown window starts)
2240
PWSMShutdownBeginMin (Minute when the cell shutdown window starts)
2241
PWSMShutdownEndHour (Hour when the cell shutdown window ends) . .
2242
PWSMShutdownEndMin (Minute when the cell shutdown window ends) .
2243
PWSMWeekday (Weekend for shutdown) . . . . . . . . . . . . . . . . . . . . . 2244
ProbabilityFactorMax (ProbabilityFactor for Congestion Indication sending)
2245
ProbabilityFactorMax2msTTI (ProbabilityFactor for Congestion Indication
sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2246
PrxAlpha (Type of measurement filter for uplink total received power) . . .
2247
PrxMeasAveWindow (Number of frames to be used averaging in PrxTotal
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2248
PrxTargetPSAdjustPeriod (PS target tune period in HSPA-DCH interference sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2249
PtxAlpha (Type of measurement filter for downlink total transmitted power)
2250
PtxDPCHmax (DPCH downlink transmission power maximum value) 2251
PtxDPCHmin (DPCH downlink transmission power minimum value) . 2253
PtxMeasAveWindow (Number of frames to be used averaging in PtxTotal
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2254
RACHloadIndicationPeriod (RACH load indication period). . . . . . . . . 2255
RFSharingState (RF Sharing State) . . . . . . . . . . . . . . . . . . . . . . . . . . 2256
RRIndPeriod (Radio Resource Indication Period) . . . . . . . . . . . . . . . 2257
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
37.67
37.67.1
37.67.2
37.67.3
37.67.4
37.67.5
37.67.6
37.67.7
37.67.8
37.67.9
37.67.10
37.68
37.69
37.70
37.71
37.72
37.73
37.74
37.75
37.76
37.77
38
38.1
38.2
38.3
38.4
38.5
38.6
38.7
38.8
38.9
38.10
38.11
38.12
38.13
38.14
DN70456011
RRMULDCHActivityFactor (Average UL DCH data rates for the radio bearers). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2259
RRMULActivityFactorPTT (Average relative UL data rate for RBs of PTT)
2260
RRMULDCHActivityFactorCSAMR (Average UL DCH data rate for RBs of
CS AMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2261
RRMULDCHActivityFactorCSNTData (Average UL DCH data rate for RB
of CS NT-data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2262
RRMULDCHActivityFactorCSTData (Average UL DCH data rate for RB of
CS T-data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2263
RRMULDCHActivityFactorPSBackgr (Average UL DCH data rate for RB of
PS background RAB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2264
RRMULDCHActivityFactorPSStream (Average UL DCH data rate for RB of
PS Streaming RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2265
RRMULDCHActivityFactorPSTHP1 (Average UL DCH data rate for RB of
PS THP1 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2266
RRMULDCHActivityFactorPSTHP2 (Average UL DCH data rate for RB of
PS THP2 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2266
RRMULDCHActivityFactorPSTHP3 (Average UL DCH data rate for RB of
PS THP3 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2267
RRMULDCHActivityFactorSRB (Average UL DCH data rate for SRB) . . .
2268
SchedulingPeriod (Scheduling period). . . . . . . . . . . . . . . . . . . . . . . . 2269
TargetId (Network Element Target Identifier). . . . . . . . . . . . . . . . . . . 2270
WBTSChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . 2271
WBTSId (WBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2272
WBTSName (WCDMA BTS name) . . . . . . . . . . . . . . . . . . . . . . . . . . 2273
WBTSSWBuildId (WBTS SW build identifier) . . . . . . . . . . . . . . . . . . 2274
WinACRABsetupDL (DL measurement averaging window for AC) . . 2275
WinACRABsetupUL (UL measurement averaging window for AC) . . 2276
WinLCHSDPA (PtxnonHSPA averaging window size for LC) . . . . . . 2277
WinLCHSUPA (Non E-DCH ST interference averaging window size for LC)
2278
WCEL Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACBarredList (Access Class Barred list) . . . . . . . . . . . . . . . . . . . . . .
AICHTraTime (AICH Transmission Timing). . . . . . . . . . . . . . . . . . . .
AMROverSC (AMROverSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMROverTransmission (AMROverTransmission) . . . . . . . . . . . . . . .
AMROverTxNC (AMROverTxNC) . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMROverTxNonHSPA (AMROverTxNonHSPA) . . . . . . . . . . . . . . . .
AMROverTxTotal (AMROverTxTotal) . . . . . . . . . . . . . . . . . . . . . . . .
AMRSF (AMRSF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMRTargetSC (AMRTargetSC). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMRTargetTransmission (AMRTargetTransmission) . . . . . . . . . . . .
AMRTargetTxNC (AMRTargetTxNC) . . . . . . . . . . . . . . . . . . . . . . . .
AMRTargetTxNonHSPA (AMRTargetTxNonHSPA) . . . . . . . . . . . . .
AMRTargetTxTotal (AMRTargetTxTotal). . . . . . . . . . . . . . . . . . . . . .
AMRUnderSC (AMRUnderSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d80580931b1d
Confidential
2280
2280
2281
2283
2284
2284
2285
2286
2287
2288
2289
2290
2291
2292
2293
51
Radio Network Parameters in Flexi Direct
38.15
38.16
38.17
38.18
38.19
38.20
38.21
38.22
38.23
38.24
38.25
38.26
38.27
38.28
38.29
38.30
38.31
38.32
38.33
38.34
38.35
38.36
38.37
38.38
38.39
38.40
38.41
38.42
38.43
38.44
38.45
38.46
38.47
38.48
38.49
38.50
38.51
38.52
52
AMRUnderTransmission (AMRUnderTransmission) . . . . . . . . . . . . . 2294
AMRUnderTxNC (AMRUnderTxNC). . . . . . . . . . . . . . . . . . . . . . . . . . 2295
AMRUnderTxNonHSPA (AMRUnderTxNonHSPA) . . . . . . . . . . . . . . 2296
AMRUnderTxTotal (AMRUnderTxTotal) . . . . . . . . . . . . . . . . . . . . . . . 2297
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA). . . 2298
AbsPrioCellReselec (Absolute priority level for cell reselection). . . . . 2300
ActivationTimeOffset (Offset for activation time). . . . . . . . . . . . . . . . . 2301
AdminCellState (Administrative Cell State). . . . . . . . . . . . . . . . . . . . . 2302
AdminPICState (Admin PIC state) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2303
AllowedPreambleSignatures (Allowed preamble signatures) . . . . . . . 2304
AllowedRACHSubChannels (Allowed RACH subchannels) . . . . . . . . 2306
AltScramblingCodeCM (Compressed Mode: Alternative scrambling code)
2307
AmpliRatioOptHSRACH (HS-RACH amplitude ratio optimized for low/high
bit rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2308
AppAwareRANCapability (Application Aware RAN Capability) . . . . . 2309
AppAwareRANEnabled (Application Aware RAN Enabled) . . . . . . . . 2310
AssignedPICPool (Cell assigned to PIC pool) . . . . . . . . . . . . . . . . . . 2311
AutoACDSACRestriction (Domain Specific Access Class Restriction). . . .
2312
AutoACRPrxTotalAvgWs (Automatic Access Class window size for averaging PrxTotal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2314
AutoACResULOLThr (Automatic Access Class Restriction Uplink Overload Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2315
BlindHOEcNoThrTarget (Blind HO EcNo threshold for target cell) . . . 2316
BlindHORSCPThrTarget (Blind HO RSCP threshold for target cell) . 2317
CCHSetupEnabled (RRC Connection Setup on CCH Enabled). . . . . 2318
CIRForFDPCH (Carrier to interference ratio for F-DPCH) . . . . . . . . . 2319
CId (Cell identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2320
CPCEnabled (CPC enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2321
CPICHEcNoSRBMapRRC (CPICH Ec/No thr for SRB mapping in RRC setup). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2323
CPICHRSCPSRBMapRRC (CPICH RSCP thr for SRB mapping in RRC
setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2324
CPICHtoRefRABoffset (Offset of the P-CPICH and reference service powers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2325
CSAMRModeSET (Configured CS AMR mode sets) . . . . . . . . . . . . . 2326
CSAMRModeSETWB (Configured CS WAMR mode sets) . . . . . . . . 2328
CSGroupId (Restriction Group Id for Circuit Switched Acces) . . . . . . 2329
CTCHCapaHighPri (CTCH capacity for High Priority CBS messages) . . .
2330
CUCEcNoThreshold (CPICH Ec/No Threshold Value For CUC Usage) . .
2331
CUCRSCPThreshold (CPICH RSCP Threshold Value For CUC Usage) . .
2333
CableLoss (Cable Loss) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2334
CellAdditionalInfo (Cell Additional Information). . . . . . . . . . . . . . . . . . 2335
CellBarred (Cell Barred) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2336
CellRange (Cell range) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2337
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
38.53
38.54
38.55
38.56
38.57
38.58
38.59
38.60
38.61
38.62
38.63
38.64
38.65
38.66
38.67
38.68
38.69
38.70
38.71
38.72
38.73
38.74
38.75
38.76
38.77
38.78
38.79
38.80
38.81
38.82
38.83
38.84
38.85
38.86
38.87
38.88
38.89
38.90
38.91
DN70456011
CellSelQualMeas (Measurement to be used as quality measure). . . 2339
CellWeightForHSDPALayering (Cell weight for HSDPA layering). . . 2340
Cell_Reserved (Cell Reserved for operator use) . . . . . . . . . . . . . . . . 2341
CodeTreeOptTimer (Code tree optimisation timer) . . . . . . . . . . . . . . 2343
CodeTreeOptimisation (Code tree optimisation) . . . . . . . . . . . . . . . . 2343
CodeTreeOptimisationGuardTime (Code Tree Optimisation Guard Time)
2344
CodeTreeUsage (Code Tree Usage). . . . . . . . . . . . . . . . . . . . . . . . . 2345
DBandHSDPAEnabled (Dual Band HSDPA Enabled). . . . . . . . . . . . 2346
DCellAndMIMOUsage (DC-HSDPA and MIMO Usage) . . . . . . . . . . 2348
DCellHSDPACapaHO (DC HSDPA Capability HO). . . . . . . . . . . . . . 2349
DCellHSDPAEnabled (DC HSDPA Enabled) . . . . . . . . . . . . . . . . . . 2351
DCellHSDPAFmcsId (DC HSDPA FMCS Identifier) . . . . . . . . . . . . . 2354
DLLoadStateTTT (DL loaded state time to trigger) . . . . . . . . . . . . . . 2355
DPCHOverHSPDSCHThreshold (NRT DPCH over HS-PDSCH code offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2356
DPCModeChangeSupport (DPC Mode Change Support) . . . . . . . . . 2357
DRRCprxMargin (Prx Margin for DRRC) . . . . . . . . . . . . . . . . . . . . . . 2358
DRRCprxOffset (Prx Offset for DRRC) . . . . . . . . . . . . . . . . . . . . . . . 2359
DRRCptxMargin (Ptx Margin for DRRC) . . . . . . . . . . . . . . . . . . . . . . 2360
DRRCptxOffset (Ptx Offset for DRRC) . . . . . . . . . . . . . . . . . . . . . . . 2361
DRXCycleHSFACH (Discontinuous Reception Cycle HS-FACH) . . . 2362
DRXInactiveTimerHSFACH (Inactivity Supervision Timer of HS-FACH for
DRX User ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2363
DRXInterruptHSDSCHData (DRX Interruption by HS-DSCH data). . 2364
DefMeasCtrlReading (Deferred Measurement Control Reading) . . . 2365
DeltaPrxMaxDown (Maximum uplink power decrease in packet scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2367
DeltaPrxMaxUp (Maximum uplink power increase in packet scheduling) .
2368
DeltaPtxMaxDown (Maximum downlink power decrease in packet scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2369
DeltaPtxMaxUp (Maximum downlink power increase in packet scheduling)
2370
DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . 2371
DirectedRRCEnabled (Directed RRC connection setup enabled) . . . 2372
DirectedRRCForHSDPALayerEnabled (Directed RRC connection setup
for HSDPA layer enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2373
EDCHCapability (E-DCH Capability) . . . . . . . . . . . . . . . . . . . . . . . . . 2374
EDCHMinSetETFCIT0 (E-DCH minimum set E-TFCI 10 ms TTI table 0) .
2375
EDCHMinimumSetETFCI (E-DCH minimum set E-TFCI 10 ms TTI table 1)
2376
EDCHOpState (Operational E-DCH state) . . . . . . . . . . . . . . . . . . . . 2377
EVAMCapability (EVAM capability) . . . . . . . . . . . . . . . . . . . . . . . . . . 2378
EVAMInUse (EVAM in use) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2379
EbNoSetIdentifier (Eb/No parameter set identifier) . . . . . . . . . . . . . . 2380
EvamDInit (Initial phase offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2381
EvamNumPhaseOffset (Phase offset amount) . . . . . . . . . . . . . . . . . 2382
Id:0900d80580931b1d
Confidential
53
Radio Network Parameters in Flexi Direct
38.92
38.93
38.94
38.95
38.96
38.97
38.98
38.99
38.100
38.101
38.102
38.103
38.104
38.105
38.106
38.107
38.108
38.109
38.110
38.111
38.112
38.113
38.114
38.115
38.116
38.117
38.118
38.119
38.120
38.121
38.122
38.123
38.124
38.125
38.126
54
EvamTKeep (Keep time). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2383
EvamTSweep (Sweep time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2384
FDPCHCodeChangeEnabled (F-DPCH code change enabled). . . . . 2385
FDPCHEnabled (F-DPCH enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2386
FDPCHSetup (F-DPCH setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2387
FachLoadMarginCCH (Margin for FACH load for downlink channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2389
FachLoadThresholdCCH (Threshold for FACH load for downlink channel
type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2390
FastActOfTargetServCell (Faster Activation Of Target Serving Cell) . 2391
FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . 2393
FastHSPAMobilityEnabled (Fast HSPA Mobility Enabled) . . . . . . . . . 2394
HCS_PRIO (HCS priority level for a cell) . . . . . . . . . . . . . . . . . . . . . . 2396
HHoMaxAllowedBitrateDL (Maximum allowed DL user bit rate in HHO) . .
2397
HHoMaxAllowedBitrateUL (Maximum allowed UL user bit rate in HHO) . .
2398
HSCapabilityHONumbUE (HSPA Capability Based Handover Max Number of UE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2399
HSCapabilityHOPeriod (HSPA Capability Based Handover Period) . 2401
HSDPA64QAMallowed (HSDPA 64 QAM allowed) . . . . . . . . . . . . . . 2401
HSDPA64UsersEnabled (HSDPA 64 users enabled). . . . . . . . . . . . . 2403
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No) 2405
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No) 2406
HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2407
HSDPAFmcgIdentifier (HSDPA FMCG identifier) . . . . . . . . . . . . . . . . 2409
HSDPAFmciIdentifier (HSDPA FMCI identifier) . . . . . . . . . . . . . . . . . 2410
HSDPAFmcsIdentifier (HSDPA FMCS identifier) . . . . . . . . . . . . . . . . 2411
HSDPALayeringCommonChEnabled (HSDPA layering for UEs in common
channels enabled). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2412
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2413
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2414
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell)
2416
HSDPAcapability (HSDPA Capability) . . . . . . . . . . . . . . . . . . . . . . . . 2417
HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2418
HSDSCHOpState (Operational HS-DSCH state) . . . . . . . . . . . . . . . . 2420
HSFACHActTimeToTrigger (Time to trigger for activity measurement on
HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2421
HSFACHActivityAveWin (Window size of HS-DSCH MAC-d flow of PS RB
on HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2423
HSFACHActivityThr (Threshold of the HS-DSCH MAC-d flow of PS RB on
HS-FACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2424
HSFACHCapability (High Speed FACH Capability) . . . . . . . . . . . . . . 2425
HSFACHDRXEnabled (UE DRX with High Speed Cell FACH Enabled) . .
2426
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
38.127
38.128
38.129
38.130
38.131
38.132
38.133
38.134
38.135
38.136
38.137
38.138
38.139
38.140
38.141
38.142
38.143
38.144
38.145
38.146
38.147
38.148
38.149
38.150
38.151
38.152
38.153
38.154
38.155
38.156
38.157
38.158
38.159
DN70456011
HSFACHEnabled (High Speed Cell_FACH DL Enabled) . . . . . . . . . 2427
HSFACHRABDRAEnabled (HSFACH direct resource allocation for NRT
HSPA RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2428
HSFACHRLCTimeToTrigger (Time to trigger for RLC measurement on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2430
HSFACHRel7ConSetupEC (HSFACH Rel7UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2432
HSFACHRel8ConSetupEC (HSFACH Rel8UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2433
HSFACHVolThrDL (DL traffic volume measurement threshold of HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2435
HSFACHVolThrDLPTT (DL traffic volume measurement threshold of HSFACH for PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2437
HSLoadStateHSDBRLimit (HSPA load state HSDPA bit rate limit). . 2438
HSLoadStateHSDOffset (HSPA load state HSDPA power Offset) . . 2439
HSLoadStateHSUBRLimit (HSPA load state E-DCH bit rate limit) . . 2440
HSLoadStateHSUOffset (HSPA load state HSUPA power Offset) . . 2441
HSLoadStateHSUResThr (HSPA Load State HSUPA Resource Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2442
HSPA128UsersPerCell (HSPA 128 Users per Cell) . . . . . . . . . . . . . 2443
HSPA72UsersPerCell (HSPA 72 Users per Cell) . . . . . . . . . . . . . . . 2445
HSPACapaHO (HSPA Capability Based Handover) . . . . . . . . . . . . . 2447
HSPAFmcsIdentifier (HSPA FMCS identifier) . . . . . . . . . . . . . . . . . . 2449
HSPAQoSEnabled (HSPA QoS enabled) . . . . . . . . . . . . . . . . . . . . . 2450
HSPASCCSpecificATO (HSPA SCC Specific ATO Value) . . . . . . . . 2453
HSPDSCHCodeSet (HS-PDSCH code set). . . . . . . . . . . . . . . . . . . . 2454
HSPDSCHMarginSF128 (HS-PDSCH code upgrade margin for SF128
codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2456
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay). 2458
HSRACHActTimeToTrigger (Time to trigger for activity measurement on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2459
HSRACHActivityAveWin (Window size of E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2461
HSRACHActivityThr (Threshold of the E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2462
HSRACHCapability (High Speed RACH Capability) . . . . . . . . . . . . . 2463
HSRACHCommonEDCHRes (Number of Common E-DCH Resources for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2464
HSRACHEnabled (High Speed RACH Enabled) . . . . . . . . . . . . . . . . 2465
HSRACHExtendedAI (Use of Extended Acquisition Indicator HS-RACH).
2466
HSRACHImplicitRelease (Common E-DCH implicit release for HS-RACH)
2467
HSRACHMPO (HS-RACH Measurement Power Offset) . . . . . . . . . . 2468
HSRACHMaxAllocTimeCCCH (Maximum E-DCH resource alloc time for
CCCH for HS-RACH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2469
HSRACHMaxPeriodCollis (Max period for collision resolution phase for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2470
HSRACHMaxTotSymbolRate (Maximum total uplink symbol rate of the
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2471
Id:0900d80580931b1d
Confidential
55
Radio Network Parameters in Flexi Direct
38.160
38.161
38.162
38.163
38.164
38.165
38.166
38.167
38.168
38.169
38.170
38.171
38.172
38.173
38.174
38.175
38.176
38.177
38.178
38.179
38.180
38.181
38.182
38.183
38.184
38.185
38.186
38.187
38.188
38.189
38.190
38.191
56
HSRACHSubChannelNumber (Available Sub Channel Number for HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2472
HSRACHTimeToTrigger (Traffic volume measurement time to trigger of
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2474
HSRACHTransmisBackOff (Additional E-DCH transmission back off for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2475
HSRACHVolThrUL (UL traffic volume measurement threshold of HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2476
HSUPA16QAMAllowed (HSUPA 16QAM usage allowed in a cell). . . 2477
HSUPA2MSTTIEnabled (HSUPA 2 ms TTI enabled). . . . . . . . . . . . . 2478
HSUPAEnabled (HSUPA enabled). . . . . . . . . . . . . . . . . . . . . . . . . . . 2480
HSUPAUserLimit16QAM (HSUPA user limit for 16QAM usage) . . . . 2482
HappyBitDelayConHSRACH (Happy bit delay condition for HS-RACH) . .
2484
HspaMultiNrtRabSupport (HSPA multi NRT RAB Support) . . . . . . . . 2485
IncomingLTEISHO (Incoming ISHO from LTE) . . . . . . . . . . . . . . . . . 2486
InitialBitRateDL (Initial bit rate in downlink). . . . . . . . . . . . . . . . . . . . . 2487
InitialBitRateUL (Initial bit rate in uplink) . . . . . . . . . . . . . . . . . . . . . . . 2488
InterFreqScaleTresel (Scaling factor of Treselection in inter-frequency
case) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2490
InterRATScaleTresel (Scaling factor of Treselection in inter-RAT case) . .
2491
IntraFreq_Cell_Reselect_Ind (Intra-frequency cell re-selection indicator) .
2492
KforCTCH (CBS frame offset (K)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2494
LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2495
LHOCapaReqRejRateDL (Load HO DL NRT capacity request rejection
rate). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2496
LHOCapaReqRejRateUL (Load HO UL NRT capacity request rejection
rate). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2497
LHODelayOFFCapaReqRejRate (Delay to broadcast NRT load based HO
state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2499
LHODelayOFFHardBlocking (Delay to broadcast hard blocking load based
HO state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2500
LHODelayOFFInterference (Delay to broadcast interference load based
HO state over). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2501
LHODelayOFFResRateSC (Delay to broadcast DL SC load based HO
state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2502
LHOHardBlockingBaseLoad (Load HO hard blocking base load) . . . 2503
LHOHardBlockingRatio (Load HO hard blocking ratio). . . . . . . . . . . . 2504
LHOHystTimeCapaReqRejRate (Hysteresis for NRT load measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2505
LHOHystTimeHardBlocking (Hysteresis for hard blocking measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2506
LHOHystTimeInterference (Hysteresis for interference measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2507
LHOHystTimeResRateSC (Hysteresis for DL SC measurement of LHO) .
2508
LHONRTTrafficBaseLoad (Load HO NRT traffic base load) . . . . . . . 2509
LHONumbUEInterFreq (Number of UEs in inter-frequency load HO ) 2510
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
38.192
38.193
38.194
38.195
38.196
38.197
38.198
38.199
38.200
38.201
38.202
38.203
38.204
38.205
38.205.1
38.206
38.207
38.208
38.209
38.210
38.211
38.212
38.213
38.214
38.215
38.216
38.217
38.218
38.219
38.220
38.221
38.222
DN70456011
LHONumbUEInterRAT (Number of UEs in inter-RAT load HO ) . . . . 2511
LHOPwrOffsetDL (Load HO DL power offset) . . . . . . . . . . . . . . . . . . 2513
LHOPwrOffsetUL (Load HO UL power offset) . . . . . . . . . . . . . . . . . . 2514
LHOResRateSC (Load HO reservation rate of DL spreading codes) 2515
LHOWinSizeOFFCapaReqRejRate (Window size for NRT load measurement to stop LHOs ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2517
LHOWinSizeOFFHardBlocking (Window size for hard blocking measurement to stop LHOs ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2518
LHOWinSizeOFFInterference (Window size for interference measurement
to stop LHOs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2519
LHOWinSizeOFFResRateSC (Window size for DL SC reservation rate
measurement to stop LHOs ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2520
LHOWinSizeONCapaReqRejRate (Window size for NRT load measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2521
LHOWinSizeONHardBlocking (Window size for hard blocking measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2522
LHOWinSizeONInterference (Window size for interference measurement
to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2523
LHOWinSizeONResRateSC (Window size for DL SC reservation rate
measurement to start LHOs ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2524
LTECellReselection (LTE Cell Reselection) . . . . . . . . . . . . . . . . . . . 2525
LayeringRRCConnRelTargFreq (Target frequency for layering in RRC
Connection Release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2525
TargetFrequency (Target frequency) . . . . . . . . . . . . . . . . . . . . . . . . . 2526
LayeringRRCRelEnabled (Layering in RRC Connection Release Enabled)
2527
LcrId (Local cell resource identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 2528
LoadBasedCPICHEcNoSRBHSPA (Load Based CPICH EcNo for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2530
LoadBasedCPICHEcNoThreEDCH2MS (Load Based CPICH EcNo
Threshold for E-DCH TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2531
MBLBInactivityEnabled (MBLB in Inactivity Enabled) . . . . . . . . . . . . 2532
MBLBLoadInfoDistr (MBLB Load Information Distribution) . . . . . . . . 2533
MBLBMobilityEnabled (MBLB in Mobility Enabled) . . . . . . . . . . . . . . 2534
MBLBRABSetupEnabled (MBLB in RAB Setup Enabled) . . . . . . . . . 2535
MBLBRABSetupMultiRAB (MBLB in RAB Setup for Multi RAB) . . . . 2536
MBLBStateTransEnabled (MBLB in State Transition Enabled) . . . . . 2537
MEHHSDPAUserNbrCQI (HSDPA CQI user number for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2539
MEHHSUPAUserNbr2msTTI (HSUPA E-DCH 2 ms TTI user number for
the Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2540
MEHLoadStateTtT (Load state time-to-trigger for the Mass Event Handler)
2541
MEHMaxHSUPAUsers (Temporary max number of HSUPA users for the
Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2542
MEHQueueThreshold (Scheduling queue threshold for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2544
MEHULLHSDPAUALimit (UL load based HSDPA user amount limit for the
MEH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2545
MHA (MHA used). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2547
Id:0900d80580931b1d
Confidential
57
Radio Network Parameters in Flexi Direct
38.223
38.224
38.225
38.226
38.227
38.228
38.229
38.230
38.231
38.232
38.233
38.234
38.235
38.236
38.237
38.238
38.239
38.240
38.241
38.242
38.243
38.244
38.245
38.246
38.247
38.248
38.249
38.250
38.251
38.252
38.253
38.254
38.255
38.256
38.257
38.258
58
MIMOEnabled (MIMO Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2549
MIMOHSDPACapaHO (MIMO HSDPA Capability Handover) . . . . . . 2551
MIMOWith64QAMUsage (MIMO with 64QAM usage) . . . . . . . . . . . . 2552
MassEventHandler (Mass Event Handler functions) . . . . . . . . . . . . . 2553
MaxBitRateDLPSNRT (Maximum downlink bit rate for PS domain NRT data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2555
MaxBitRateULPSNRT (Maximum uplink bit rate for PS domain NRT data)
2556
MaxCodeReleases (Max Code Releases) . . . . . . . . . . . . . . . . . . . . . 2558
MaxDLPowerCapability (Maximum DL Power Capability) . . . . . . . . . 2558
MaxIncrInterferenceUL (Max increment in the received wide band interference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2559
MaxNbrOfHSSCCHCodes (Maximum number of HS-SCCH codes) . 2561
MaxNumbHSDPAUsersS (Max number HSDPA users per MAChs/ehs
scheduler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2562
MaxNumbHSDSCHMACdFS (Max number HSDSCH MACd flows per
MAChs/ehs scheduler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2563
MaxNumberEDCHCell (Maximum number of E-DCHs in the cell) . . . 2565
MaxNumberHSDPAUsers (Maximum number of HSDPA users) . . . . 2566
MaxNumberHSDSCHMACdFlows (Maximum number of HS-DSCH MACd flows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2568
MaxNumberUECmHO (Maximum number of UEs in CM due to critical HO
measurement ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2569
MaxNumberUECmSLHO (Maximum number of UEs in CM due to SLHO
measurement ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2570
MaxNumberUEHSPACmHO (Max number of UEs in HSDPA CM due to
critical HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2572
MaxNumberUEHSPACmNCHO (Max number of UEs in HSDPA CM due
to NCHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2573
MaxTotalUplinkSymbolRate (Maximum total uplink symbol rate) . . . . 2575
MinAllowedBitRateDL (Minimum allowed bit rate in downlink) . . . . . . 2577
MinAllowedBitRateUL (Minimum allowed bit rate in uplink) . . . . . . . . 2579
MultiplePLMNListIncluded (Multiple PLMN List Included) . . . . . . . . . 2580
N300 (N300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2581
N312 (N312) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2582
N312Conn (N312 for connected mode) . . . . . . . . . . . . . . . . . . . . . . . 2584
N313 (N313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2585
N315 (N315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2586
NASsignVolThrDL (Downlink NAS signalling volume threshold) . . . . 2588
NASsignVolThrUL (Uplink NAS signalling volume threshold). . . . . . . 2589
NCr (Maximum number of cell reselections) . . . . . . . . . . . . . . . . . . . . 2590
NbrOfSCCPCHs (Number of SCCPCHs) . . . . . . . . . . . . . . . . . . . . . . 2592
NforCTCH (Period of CTCH allocation (N)) . . . . . . . . . . . . . . . . . . . . 2593
NonHCSNcr (Maximum number of cell reselections in non-HCS case) . . .
2595
NonHCSTcrMax (Evaluating period for amount of reselections in nonHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2596
NonHCSTcrMaxHyst (Hysteresis to revert from UE measurement in nonHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2597
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
38.259
38.260
38.261
38.262
38.263
38.264
38.265
38.266
38.266.1
38.266.2
38.266.3
38.267
38.268
38.269
38.270
38.271
38.272
38.273
38.274
38.275
38.276
38.277
38.278
38.279
38.280
38.281
38.282
38.283
38.284
38.285
38.286
38.287
38.288
38.289
38.290
38.291
DN70456011
NrtFmcgIdentifier (NRT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . 2599
NrtFmciIdentifier (NRT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2600
NrtFmcsIdentifier (NRT FMCS Identifier). . . . . . . . . . . . . . . . . . . . . . 2601
NumberEDCHReservedSHOBranchAdditions (Number of E-DCHs reserved for SHO branch additions) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2602
OCULNRTDCHGrantedMinAllocT (DCH time limit for UL NRT DCH overload in E-DCH cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2603
OCdlNrtDCHgrantedMinAllocT (Threshold for DL NRT DCH allocation time
in enhanced overload control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2605
OffsetToBeginCTCHBSIndex (Offset to Begin CTCH Block Set Index) . .
2606
PBSgrantedMinDCHallocT (PBS granted min DCH allocation time) . 2607
PBSgrantedMinDCHallocTequalP (PBS granted min DCH allocation time
equal priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2608
PBSgrantedMinDCHallocThigherP (PBS granted min DCH allocation time
higher priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2609
PBSgrantedMinDCHallocTlowerP (PBS granted min DCH allocation time
lower priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2610
PCH24kbpsEnabled (Activate \ Deactivate support for 24kbps PCH) 2611
PFLIdentifier (PFL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2612
PICState (PIC state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2613
PI_amount (Number of PI per frame). . . . . . . . . . . . . . . . . . . . . . . . . 2614
PRACHDelayRange (PRACH Propagation Delay Statistics Cell Range) .
2615
PRACHRequiredReceivedCI (Required received C/I on PRACH at WCDMA BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2616
PRACHScramblingCode (PRACH scrambling code). . . . . . . . . . . . . 2617
PRACH_preamble_retrans (PRACH Preamble Retrans Max) . . . . . 2618
PSGroupId (Restriction Group Id for Packet Switched Acces) . . . . . 2619
PTxPICH (Transmission power of the PICH channel) . . . . . . . . . . . . 2620
PWSMAVLimitDCHSDPA (Limit for DC HSDPA users in activation) 2622
PWSMAVLimitNRTHSDPA (Limit for NRT HSDPAs for Cell Activation Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2623
PWSMAVLimitRTDCH (RT DCH power limit for activation) . . . . . . . 2623
PWSMAVLimitRTHSDPA (Limit for RT HSDPAs for Cell Activation Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2624
PWSMAVPwrNRTHSDPA (NRT HSDPA power per user limit) . . . . 2625
PWSMAVPwrRTHSDPA (RT HSDPA power limit for activation) . . . 2626
PWSMCellGroup (The PWSM cell group of a cell.). . . . . . . . . . . . . . 2627
PWSMEXPwrLimit (Power limit for virtual AC) . . . . . . . . . . . . . . . . . 2628
PWSMEXUsrLimit (User limit for virtual AC) . . . . . . . . . . . . . . . . . . . 2629
PWSMSDLimitDCHSDPA (Limit for DC HSDPA users in shutdown) 2629
PWSMSDLimitNRTDCH (NRT DCH limit for shutdown) . . . . . . . . . . 2630
PWSMSDLimitNRTHSDPA (Limit for NRT HSDPAs for Cell Shutdown Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2631
PWSMSDLimitRTDCH (RT DCH limit for shutdown). . . . . . . . . . . . . 2632
PWSMSDLimitRTHSDPA (Limit for RT HSDPAs for Cell Shutdown Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2633
PWSMSDPwrNRTHSDPA (NRT HSDPA power per user margin) . . 2634
Id:0900d80580931b1d
Confidential
59
Radio Network Parameters in Flexi Direct
38.292
38.293
38.294
38.295
38.296
38.297
38.298
38.298.1
38.298.2
38.298.3
38.299
38.300
38.301
38.302
38.303
38.304
38.305
38.306
38.307
38.308
38.309
38.310
38.311
38.312
38.313
38.314
38.315
38.316
38.317
38.318
38.319
38.320
38.321
38.322
60
PWSMSDPwrRTDCH (RT DCH Power limit for shutdown) . . . . . . . . 2635
PWSMSDPwrRTHSDPA (RT HSDPA power limit for shutdown) . . . . 2635
PWSMShutdownOrder (The shutdown order of cells in one PWSM cell
group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2636
PWSMShutdownRemCell (Shutdown of a remaining cell) . . . . . . . . . 2637
PowerOffsetLastPreamblePRACHmessage (Power offset last preamble
and PRACH message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2638
PowerOffsetPreamHSRACH (Power Offset Last Transmitted Preamble for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2639
PowerOffsetSCCPCHTFCI (Power offset for S-CCPCH TFCI) . . . . . 2640
PO1_15 (Power offset for SCCPCH TFCI (15 ksps)) . . . . . . . . . . . . . 2642
PO1_30 (Power offset for SCCPCH TFCI (30 ksps)) . . . . . . . . . . . . . 2643
PO1_60 (Power offset for SCCPCH TFCI (60 ksps)) . . . . . . . . . . . . . 2644
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2645
PowerRampStepPRACHpreamble (Power ramp step on PRACH preamble) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2647
PowerSaveHSPAType (HSPA Type of Cell in Power Saving Mode) . 2647
PriScrCode (Primary downlink scrambling code) . . . . . . . . . . . . . . . . 2649
PrxLoadMarginDCH (Interference margin for the minimum UL DCH load)
2650
PrxLoadMarginEDCH (Interference margin for the minimum E-DCH load)
2652
PrxLoadMarginMaxDCH (Interference margin for the maximum UL DCH
load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2653
PrxMaxOrigTargetBTS (Max target received wide band original power for
BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2654
PrxMaxTargetBTS (Maximum target received wide band power for BTS) .
2656
PrxMeasFilterCoeff (Filtering Coefficient of PrxTotal measurement) . 2657
PrxNoise (Uplink noise level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2658
PrxNoiseAutotuning (PrxNoise autotuning allowed) . . . . . . . . . . . . . . 2659
PrxOffset (Offset for received power) . . . . . . . . . . . . . . . . . . . . . . . . . 2660
PrxOffsetWPS (Offset for received Wireless Priority Service power) . 2661
PrxTarget (Target for received power) . . . . . . . . . . . . . . . . . . . . . . . . 2663
PrxTargetMax (Maximum target for the received total wideband power) . .
2664
PrxTargetPSMax (Max PS target in HSPA-DCH interference sharing) . . .
2665
PrxTargetPSMaxtHSRACH (Max PS target interference level with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2666
PrxTargetPSMin (Min PS target in HSPA-DCH interference sharing) 2667
PrxTargetPSStepDown (PS target step down in HSPA-DCH interference
sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2669
PrxTargetPSStepUp (PS target step up in HSPA-DCH interference sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2670
PtxAICH (Transmission power of the AICH channel) . . . . . . . . . . . . . 2671
PtxBCCHHSPDSCH (HS-PDSCH Power of HS-FACH for BCCH) . . 2672
PtxBCCHHSSCCH (HS-SCCH Power of HS-FACH for BCCH) . . . . . 2673
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
38.323
38.324
38.325
38.326
38.327
38.328
38.329
38.330
38.331
38.332
38.333
38.334
38.335
38.336
38.337
38.338
38.339
38.340
38.341
38.342
38.343
38.344
38.345
38.346
38.347
38.348
38.349
38.350
38.351
38.352
38.353
38.354
38.355
38.356
38.357
DN70456011
PtxCellMax (Cell maximum transmission power). . . . . . . . . . . . . . . . 2674
PtxDLabsMax (Planned maximum downlink transmission power of a radio
link) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2675
PtxFDPCHMax (F-DPCH maximum transmission power) . . . . . . . . . 2676
PtxFDPCHMin (F-DPCH minimum transmission power) . . . . . . . . . . 2677
PtxHighHSDPAPwr (High threshold of PtxTotal for dynamic HSDPA pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2679
PtxMarginCCH (Margin for total downlink transmission power for downlink
channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2680
PtxMaxEHICH (The Maximum transmission power E-HICH) . . . . . . 2680
PtxMaxHSDPA (Maximum allowed HSDPA power) . . . . . . . . . . . . . 2681
PtxMeasFilterCoeff (Filtering Coefficient of PtxTotal measurement) . 2683
PtxOffset (Offset for transmitted power) . . . . . . . . . . . . . . . . . . . . . . 2684
PtxOffsetEAGCH (The transmission power offset of the E-AGCH) . . 2685
PtxOffsetEAGCHDPCCH (The power offset of the E-AGCH) . . . . . . 2686
PtxOffsetEHICHDPCCH (The power offset of the E-HICH). . . . . . . . 2688
PtxOffsetERGCH (The transmission power offset of the E-RGCH). . 2689
PtxOffsetERGCHDPCCH (The power offset of the E-RGCH) . . . . . . 2690
PtxOffsetExxCH2ms (The power offset of E-xxCH for 2ms TTI) . . . . 2692
PtxOffsetExxCHSHO (The power offset of E-xxCH for SHO) . . . . . . 2693
PtxOffsetFDPCHSHO (The power offset of F-DPCH for SHO) . . . . . 2694
PtxOffsetHSDPA (Offset for transmitted non-HSDPA power) . . . . . . 2695
PtxOffsetWPS (Offset for transmitted Wireless Priority Service power) . .
2696
PtxPSstreamAbsMax (Maximum transmitted code power of PS streaming
RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2697
PtxPrimaryCCPCH (Transmission power of the primary CCPCH channel)
2698
PtxPrimaryCPICH (Transmission power of the primary CPICH channel) .
2700
PtxPrimarySCH (Transmission power of the primary SCH channel) . 2701
PtxSCCPCH1 (Tx power of S-CCPCH for PCH/FACH(s) or standalone
FACH(s)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2703
PtxSCCPCH2 (Tx power of S-CCPCH for Standalone PCH) . . . . . . 2704
PtxSCCPCH2SF128 (Tx power of S-CCPCH for Standalone PCH SF 128)
2706
PtxSCCPCH3 (Tx power of S-CCPCH for SAB) . . . . . . . . . . . . . . . . 2707
PtxSecSCH (Transmission power of the secondary SCH channel). . 2708
PtxTarget (Target for transmitted power). . . . . . . . . . . . . . . . . . . . . . 2710
PtxTargetHSDPA (Target for transmitted non-HSDPA power) . . . . . 2711
PtxTargetPSAdjustPeriod (DCH PS target adjust period for dyn HSDPA
pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2712
PtxTargetPSMax (Max DCH PS target for dynamic HSDPA pwr allocation)
2713
PtxTargetPSMaxtHSRACH (Max PS target power level with HS-RACH) .
2715
PtxTargetPSMin (Min DCH PS target for dynamic HSDPA pwr allocation)
2716
Id:0900d80580931b1d
Confidential
61
Radio Network Parameters in Flexi Direct
38.358
38.359
38.360
38.361
38.362
38.363
38.364
38.365
38.366
38.367
38.368
38.369
38.370
38.371
38.372
38.373
38.374
38.375
38.376
38.377
38.378
38.379
38.380
38.381
38.382
38.383
38.384
38.385
38.386
38.387
38.388
38.389
38.390
62
PtxTargetPSStepDown (DCH PS target step down for dynamic HSDPA
pwr alloc). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2717
PtxTargetPSStepUp (DCH PS target step up for dynamic HSDPA pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2718
PtxTargetTotMax (Maximum value for dynamic total tx power) . . . . . 2719
PtxTargetTotMin (Minimum value for dynamic total tx power) . . . . . . 2721
PtxThresholdCCH (Threshold for total downlink transmission power for
downlink channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2722
QHCS (Quality threshold level for HCS) . . . . . . . . . . . . . . . . . . . . . . . 2723
Qhyst1 (Cell reselection hysteresis 1) . . . . . . . . . . . . . . . . . . . . . . . . 2724
Qhyst1FACH (Cell reselection hysteresis 1 for FACH). . . . . . . . . . . . 2725
Qhyst1PCH (Cell reselection hysteresis 1 for PCH) . . . . . . . . . . . . . . 2726
Qhyst2 (Cell reselection hysteresis 2) . . . . . . . . . . . . . . . . . . . . . . . . 2727
Qhyst2FACH (Cell reselection hysteresis 2 for FACH). . . . . . . . . . . . 2728
Qhyst2PCH (Cell reselection hysteresis 2 for PCH) . . . . . . . . . . . . . . 2729
QqualMin (Minimum required quality level in the cell) . . . . . . . . . . . . 2730
QrxlevMin (Minimum required RX level in the cell) . . . . . . . . . . . . . . . 2731
RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2732
RACHCapacity (RACH Capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2734
RACHInterFreqMesQuant (RACH Inter Frequency Measurement Quantity)
2735
RACHIntraFreqMesQuant (RACH Intra Frequency Measurement Quantity)
2736
RACH_Tx_NB01max (RACH random back-off upper bound) . . . . . . 2737
RACH_Tx_NB01min (RACH random back-off lower bound) . . . . . . . 2739
RACH_tx_Max (RACH maximum number of preamble cycles) . . . . . 2740
RACHmeasFilterCoeff (Filtering Coefficient of PRACH measurement) . . .
2742
RNARGroupId (Radio Network Access Regulation Function Group Id) . . .
2743
RRCconnRepTimer1 (RRC connection setup Retransmission Timer1) . . .
2744
RRCconnRepTimer2 (RRC connection setup Retransmission Timer2) . . .
2745
RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for speech services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2747
RTWithHSDPAFmciIdentifier (HSDPA FMCI identifier for speech services)
2748
RTWithHSDPAFmcsIdentifier (HSDPA FMCS identifier for speech services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2750
RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for speech services).
2751
RXBurstHSFACH (HS-FACH Reception Burst) . . . . . . . . . . . . . . . . . 2752
RachLoadMarginCCH (Margin for RACH load for downlink channel type
selection). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2753
RachLoadThresholdCCH (Threshold for RACH load for downlink channel
type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2754
RefServForCodePower (Reference service in the max code power definition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2755
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
38.391
38.392
38.393
38.394
38.395
38.396
38.397
38.398
38.399
38.400
38.401
38.402
38.403
38.404
38.405
38.406
38.407
38.408
38.409
38.410
38.411
38.412
38.413
38.414
38.415
38.416
38.417
38.418
38.419
38.420
38.421
38.422
38.423
38.424
38.425
38.426
38.427
38.428
38.429
38.430
DN70456011
RelocComm_in_InterRNC_HHO (Usage of Relocation Commit procedure
in inter RNC HHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2757
RsrvdSignaturesOffset (Reserved E-RGCH and E-HICH signatures per
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2758
RtFmcgIdentifier (RT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2759
RtFmciIdentifier (RT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 2760
RtFmcsIdentifier (RT FMCS Identifier). . . . . . . . . . . . . . . . . . . . . . . . 2761
RxDivIndicator (Rx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . 2762
SABEnabled (Service Area Broadcast Enabled) . . . . . . . . . . . . . . . . 2763
SAC (Service Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2764
SACB (Service Area Code for SAB) . . . . . . . . . . . . . . . . . . . . . . . . . 2765
SHCS_RAT (Threshold for inter-RAT measurement rules in HCS). . 2766
SHCS_RATConn (Threshold for inter-RAT measurement for connected
mode ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2767
SIB11Length (Length of SIB11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2768
SIB11bisLength (Length of SIB11bis) . . . . . . . . . . . . . . . . . . . . . . . . 2769
SIB12Length (Length of SIB12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2770
SIB4Indicator (Indicator of SIB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2771
SIB7factor (SIB7 expiration time factor). . . . . . . . . . . . . . . . . . . . . . . 2771
SIRDPCCHOffsetEDPCH (SIR target offset for DPCCH with E-DPCH) . .
2773
SRBBitRateRRCSetupEC (SRB DCH bit rate in RRC setup based on EC)
2773
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . 2775
SRBHSPAFmcsId (FMCS identifier for standalone SRB on HSPA) . 2776
SRBMapRRCSetupEC (SRB mapping in RRC setup based on EC). 2777
SectorID (Sector Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2779
ServHONumbUEInterFreq (Number of inter-frequency service HOs) 2780
ServHONumbUEInterRAT (Number of inter-RAT service HOs) . . . . 2781
ServHOPeriodInterFreq (Period to start inter-frequency service HOs)2783
ServHOPeriodInterRAT (Period to start inter-RAT service HOs). . . . 2784
ShutdownStepAmount (Shutdown step amount) . . . . . . . . . . . . . . . . 2785
ShutdownWindow (Shutdown window) . . . . . . . . . . . . . . . . . . . . . . . 2785
Sintersearch (S intersearch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2786
SintersearchConn (S intersearch for connected mode). . . . . . . . . . . 2787
Sintrasearch (S intrasearch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2789
SintrasearchConn (S intrasearch for connected mode). . . . . . . . . . . 2790
Slimit_SearchRAT (S limit,SearchRAT). . . . . . . . . . . . . . . . . . . . . . . 2791
Slimit_SearchRATConn (S limit,SearchRAT for connected mode) . . 2792
SmartLTELayeringEnabled (Smart LTE Layering Enabled) . . . . . . . 2793
SmartLTELayeringRSCP (Smart LTE Layering RSCP threshold). . . 2795
SmartLTELayeringTSysSel (Smart LTE Layering Target System Selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2797
SmartLTELayeringUA (Smart LTE Layering NRT user amount threshold)
2798
SmartTrafVolThrDL (DL traffic volume threshold for Smartphone) . . 2799
SmartTrafVolThrUL (UL traffic volume threshold for Smartphone) . . 2800
Id:0900d80580931b1d
Confidential
63
Radio Network Parameters in Flexi Direct
38.431
38.432
38.433
38.434
38.435
38.436
38.437
38.438
38.439
38.440
38.441
38.442
38.443
38.444
38.445
38.446
38.447
38.448
38.449
38.450
38.451
38.452
38.453
38.454
38.455
38.456
38.457
38.458
38.459
38.460
38.461
38.462
38.463
38.464
38.465
38.466
38.467
38.468
64
SpeedScaleTresel (Scaling factor of Treselection for UE in high mobility) .
2802
Sprioritysearch1 (S prioritysearch1) . . . . . . . . . . . . . . . . . . . . . . . . . . 2803
Sprioritysearch2 (S prioritysearch2) . . . . . . . . . . . . . . . . . . . . . . . . . . 2804
SsearchHCS (S searchHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2806
SsearchHCSConn (S searchHCS for connected mode). . . . . . . . . . . 2807
Ssearch_RAT (S searchRAT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2808
Ssearch_RATConn (S searchRAT for connected mode) . . . . . . . . . . 2809
T300 (T300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2810
T312 (T312) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2811
T312Conn (T312 for connected mode). . . . . . . . . . . . . . . . . . . . . . . . 2813
T313 (T313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2814
T315 (T315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2815
T321 (High Speed Cell FACH DRX operation timer) . . . . . . . . . . . . . 2816
TBarred (Cell barred period) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2816
TCrmax (Evaluating period for amount of cell reselections) . . . . . . . . 2818
TCrmaxHyst (Hysteresis to revert from UE high-mobility measurements) .
2819
TPCCommandERTarget (TPC command error rate target) . . . . . . . . 2820
TargetNSEDCHToTotalEDCHPR (Target non-serving E-DCH to total EDCH power ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2822
Tcell (Frame timing offset of a cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2823
Threshservlow (Thresh serving low) . . . . . . . . . . . . . . . . . . . . . . . . . 2825
ToAWE_CCH (Time of Arrival Window Endpoint for common channels). .
2827
ToAWS_CCH (Time of Arrival Window Startpoint for common channels) .
2828
TrafVolThresholdDLLow (Downlink traffic volume measurement low
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2829
Treselection (Cell reselection triggering time). . . . . . . . . . . . . . . . . . . 2830
TreselectionFACH (Cell reselection triggering time for FACH) . . . . . . 2831
TreselectionPCH (Cell reselection triggering time for PCH) . . . . . . . . 2833
UARFCN (UTRA Absolute Radio Frequency Channel Number) . . . . 2834
UEDRXCapability (UE DRX in Cell_FACH capability) . . . . . . . . . . . . 2837
UEtxPowerMaxDPCH (Maximum UE transmission power on DPCH) 2838
UEtxPowerMaxPRACH (Maximum UE transmission power on PRACH) . .
2839
UEtxPowerMaxPRACHConn (Max UE transmission power on PRACH for
connected mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2840
ULLoadStateHSUBRLimit (UL loaded state for HSPAusers bit rate limit) .
2841
ULLoadStateHSUOffset (UL loaded state for HSPA users offset) . . . 2842
URAId (URA identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2843
UTRAN_DRX_length (UTRAN DRX cycle length) . . . . . . . . . . . . . . . 2844
UseOfHCS (Use of HCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2845
UsersPerHSSCCHCode (Max nbr of conv users per reserved HS-SCCH
code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2846
VCPMaxHSDPAUsers (Temporary max number of HSDPA users for the
VCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2847
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
38.469
38.470
38.471
38.472
38.473
38.474
38.474.1
38.474.2
38.474.3
38.475
39
39.1
39.2
39.3
39.3.1
39.3.2
39.3.3
39.3.4
39.3.5
39.3.6
39.3.7
39.3.8
39.3.9
39.3.10
39.3.11
39.3.12
39.4
39.5
39.6
39.7
39.8
39.9
39.10
39.10.1
39.10.2
39.10.3
DN70456011
VCPPtxOffset (Voice Call Priority target threshold for HSDPA prevention)
2848
VoiceCallPriority (Voice Call Prioritisation During High Traffic Load) 2850
VoiceOverrideSTHSUPA (Override switch for voice services in the HSUPA
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2851
WACSetIdentifier (WAC Parameter Set Identifier). . . . . . . . . . . . . . . 2852
WCELChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . . 2853
WCELGlobalCNid (Global CN Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2854
WCELMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . 2855
WCELMNC (Mobile Network Code). . . . . . . . . . . . . . . . . . . . . . . . . . 2856
WCELMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . 2857
WCelState (WCDMA Cell Operational State) . . . . . . . . . . . . . . . . . . 2858
WLCSE Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2861
AntBearing (Antenna Bearing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2861
AntHPBW (Antenna HPBW (Half Power Beam Width) for Cell) . . . . 2861
AntennaCoord (Antenna Coordinates). . . . . . . . . . . . . . . . . . . . . . . . 2862
AntennaCoordAltitudeDirect (Antenna Coordinates Altitude Direction) . . .
2864
AntennaCoordAltitudeGround (Antenna Coordinates Altitude of Ground
Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2865
AntennaCoordLatitudeDegrees (Antenna Coordinates Latitude Degrees)
2866
AntennaCoordLatitudeFractions (Antenna Coordinates Latitude Fractions)
2866
AntennaCoordLatitudeMinutes (Antenna Coordinates Latitude Minutes) .
2867
AntennaCoordLatitudeSeconds (Antenna Coordinates Latitude Seconds)
2868
AntennaCoordLatitudeSign (Antenna Coordinates Latitude Sign). . . 2869
AntennaCoordLongitudeDegrees (Antenna Coordinates Longitude Degrees). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2870
AntennaCoordLongitudeFractions (Antenna Coordinates Longitude Fractions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2871
AntennaCoordLongitudeMinutes (Antenna Coordinates Longitude Minutes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2872
AntennaCoordLongitudeSeconds (Antenna Coordinates Longitude Seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2873
AntennaCoordLongitudeSign (Antenna Coordinates Longitude Sign) 2873
CovType (Coverage Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2874
EnvCharact (Environment characterisation) . . . . . . . . . . . . . . . . . . . 2875
MaxCellBackRad (Maximum Cell back radius) . . . . . . . . . . . . . . . . . 2876
MaxCellRad (Maximum cell radius) . . . . . . . . . . . . . . . . . . . . . . . . . . 2877
RepeaterExist (Repeater exist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2878
WLCSEChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 2879
WLCSEUtranCellId (LCSE UTRAN Cell Id). . . . . . . . . . . . . . . . . . . . 2880
WLCSECId (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2881
WLCSEMCC (Mobile Country Code). . . . . . . . . . . . . . . . . . . . . . . . . 2882
WLCSEMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . 2882
Id:0900d80580931b1d
Confidential
65
Radio Network Parameters in Flexi Direct
39.10.4
39.10.5
39.11
WLCSEMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . 2883
WLCSERncId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2884
WLCSEid (WLCSE Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2885
40
40.1
40.1.1
WRAB Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2887
DeltaSIR (Delta SIR in the compressed mode) . . . . . . . . . . . . . . . . . 2887
DeltaSIRAfterDownlink (Downlink delta SIR after in the compressed mode)
2888
DeltaSIRAfterUplink (Uplink delta SIR after in the compressed mode) . . .
2888
DeltaSIRDownlink (Downlink delta SIR in the compressed mode) . . . 2889
DeltaSIRUplink (Uplink delta SIR in the compressed mode) . . . . . . . 2890
DownlinkOrthog (Downlink orthogonality factor) . . . . . . . . . . . . . . . . . 2891
EDCHBLERAdjCSVoice10 (HARQ threshold for OLPC of HS CS voice ETTI 10 ms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2892
EDCHBLERAdjCSVoice2 (HARQ threshold for OLPC of HS CS voice ETTI 2 ms). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2893
EDCHBLERAdjPSConvSpe10 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2895
EDCHBLERAdjPSConvSpe2 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2896
EbNoDCHOfPSNRT (Rate matching with the PS NRT DCH) . . . . . . 2897
EbNoDCHOfPSNRTPriQua (Primary quality target of the PS NRT DCH) .
2899
EbNoDCHOfPSNRTPrim (Primary Eb/N0 of the PS NRT DCH) . . . . 2900
EbNoDCHOfPSNRTSec (Secondary Eb/N0 of the PS NRT DCH) . . 2901
EbNoDCHOfPSNRTSecQua (Secondary quality target of the PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2903
EbNoDCHOfPSNRTSelQuaDL (Quality target selector for DL PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2904
EbNoDCHOfPSNRTSelQuaUL (Quality target selector for UL PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2905
EbNoDCHOfPSStr (Rate matching with the PS streaming DCH). . . . 2907
EbNoDCHOfPSStrPriQua (Primary quality target of the PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2908
EbNoDCHOfPSStrPrim (Primary Eb/N0 of the PS streaming DCH) . 2909
EbNoDCHOfPSStrSec (Secondary Eb/N0 of the PS streaming DCH)2911
EbNoDCHOfPSStrSecQua (Secondary quality target of the PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2912
EbNoDCHOfPSStrSelQuaDL (Quality target selector for DL PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2913
EbNoDCHOfPSStrSelQuaUL (Quality target selector for UL PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2915
EbNoDCHOfSRB (Rate matching with the SRB DCH). . . . . . . . . . . . 2916
EbNoDCHOfSRB136 (Planned Eb/N0 of the SRB13.6 DCH) . . . . . . 2917
EbNoDCHOfSRB136Qua (Quality target of the SRB13.6 DCH) . . . . 2919
EbNoDCHOfSRB34 (Planned Eb/N0 of the SRB3.4 DCH) . . . . . . . . 2920
EbNoDCHOfSRB34Qua (Quality target of the SRB3.4 DCH) . . . . . . 2921
EbNoDCHRateGain (Data rate gain in the Eb/N0 definition) . . . . . . . 2922
40.1.2
40.1.3
40.1.4
40.2
40.3
40.4
40.5
40.6
40.7
40.7.1
40.7.2
40.7.3
40.7.4
40.7.5
40.7.6
40.8
40.8.1
40.8.2
40.8.3
40.8.4
40.8.5
40.8.6
40.9
40.9.1
40.9.2
40.9.3
40.9.4
40.10
66
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
40.10.1
40.10.2
40.10.3
40.10.4
40.10.5
40.10.6
40.10.7
40.11
40.12
40.13
40.14
40.15
40.15.1
40.15.2
40.15.3
40.15.4
40.15.5
40.15.6
40.15.7
40.16
40.17
40.17.1
40.17.2
40.17.3
40.17.4
40.18
40.18.1
40.18.2
40.18.3
40.18.4
40.18.5
40.19
40.19.1
DN70456011
EbNoDCHRateGainCSAMR (Data rate gain for the Eb/N0 of the CS AMR)
2924
EbNoDCHRateGainCSData (Data rate gain for the Eb/N0 of the CS data)
2926
EbNoDCHRateGainPSConvSpe (Data rate gain for the Eb/N0 of the PS
conv speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2928
EbNoDCHRateGainPSData (Data rate gain for the Eb/N0 of the PS data
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2930
EbNoDCHRateGainSFDown (Data rate gain selector for the Eb/N0 of the
DL DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2932
EbNoDCHRateGainSFUp (Data rate gain selector for the Eb/N0 of the UL
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2933
EbNoDCHRateGainSRB (Data rate gain for the Eb/N0 of the SRB) . 2934
EbNoDCHRxDiv2 (Cell offset in the UL Eb/N0, 2-way Rx diversity) . 2936
EbNoDCHRxDiv4 (Cell offset in the UL Eb/N0, 4-way Rx diversity) . 2937
EbNoDCHTxDiv (Cell offset in the DL Eb/N0 definition) . . . . . . . . . . 2938
EbNoEDCHCSAMR (Eb/N0 planned for the E-DCH MAC-d flow of CS
voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2939
EbNoEDCHOfPSStr (EbNo for E-DCH Streaming) . . . . . . . . . . . . . . 2940
EDCHPSStr128Kbps (EbNo for E-DCH Streaming 128Kbps). . . . . . 2942
EDCHPSStr16Kbps (EbNo for E-DCH Streaming 16Kbps). . . . . . . . 2942
EDCHPSStr248Kbps (EbNo for E-DCH Streaming 248Kbps). . . . . . 2943
EDCHPSStr32Kbps (EbNo for E-DCH Streaming 32Kbps). . . . . . . . 2944
EDCHPSStr64Kbps (EbNo for E-DCH Streaming 64Kbps). . . . . . . . 2945
EDCHPSStr8Kbps (EbNo for E-DCH Streaming 8Kbps). . . . . . . . . . 2946
EDCHPSStrOver248Kbps (EbNo for E-DCH Streaming over 248Kbps). .
2947
EbNoEDCHPSConvSpeech (Eb/N0 planned for E-DCH PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2948
EbNoOfCSData (Rate matching with the CS data services) . . . . . . . 2949
EbNoDCHOfCSDataNT (Planned Eb/N0 of the CS non transparent data)
2951
EbNoDCHOfCSDataNTQua (Quality target of the CS non transparent data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2952
EbNoDCHOfCSDataT (Planned Eb/N0 of the CS transparent data). 2953
EbNoDCHOfCSDataTQua (Quality target of the CS transparent data). . .
2955
EbNoOfCSNBAMR (Rate matching with the CS NB-AMR) . . . . . . . . 2956
EbNoDCHOfCSNBAMR122 (Planned Eb/N0 of the CS NB-AMR 12.2) . .
2957
EbNoDCHOfCSNBAMR59 (Planned Eb/N0 of the CS NB-AMR 5.9) 2959
EbNoDCHOfCSNBAMRQua (Quality target of the CS NB AMR) . . . 2960
EbNoDCHOfCSNBAMRb (Planned Eb/N0 the CS NB-AMR subflow B) . .
2961
EbNoDCHOfCSNBAMRc (Planned Eb/N0 the CS NB-AMR subflow C) . .
2962
EbNoOfCSWBAMR (Rate matching with the CS WB-AMR) . . . . . . . 2963
EbNoDCHOfCSWBAMR1265 (Planned Eb/N0 of the CS WB-AMR 12.65)
2964
Id:0900d80580931b1d
Confidential
67
Radio Network Parameters in Flexi Direct
40.19.2
40.19.3
40.20
40.20.1
40.20.2
40.21
40.22
40.23
40.24
40.25
40.25.1
40.25.2
40.25.3
40.25.4
40.25.5
40.25.6
40.25.7
40.25.8
40.25.9
40.25.10
40.25.11
40.25.12
40.25.13
40.25.14
40.25.15
40.25.16
68
EbNoDCHOfCSWBAMRQua (Quality target of the CS WB-AMR) . . . 2966
EbNoDCHOfCSWBAMRb (Planned Eb/N0 the CS WB-AMR subflow B) .
2967
EbNoOfPSConvSpe (Rate matching with the PS conversational speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2968
EbNoDCHOfPSConvSpe (Planned Eb/N0 of the PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2969
EbNoDCHOfPSConvSpeQua (Quality target of the PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2970
L1BLERTEDCHPSConvSpe10 (BLER target for PS Conversational
speech E-TTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2971
L1BLERTEDCHPSConvSpe2 (BLER target for PS Conversational speech
E-TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2973
L1BLERTEDCHVoice10 (BLER target for the HS CS voice E-TTI 10 ms) .
2974
L1BLERTEDCHVoice2 (BLER target for the HS CS voice E-TTI 2 ms). . .
2975
SIRDPCCHInitialDCH (Initial SIR target for UL DPCCH with DPDCH) . . .
2976
SIRDPCCHInitialDCH128 (UL SIR target without HS-DPCCH - DPDCH SF
128). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2978
SIRDPCCHInitialDCH16 (UL SIR target without HS-DPCCH - DPDCH SF
16). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2979
SIRDPCCHInitialDCH256 (UL SIR target without HS-DPCCH - DPDCH SF
256). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2980
SIRDPCCHInitialDCH32 (UL SIR target without HS-DPCCH - DPDCH SF
32). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2982
SIRDPCCHInitialDCH4 (UL SIR target without HS-DPCCH - DPDCH SF 4)
2983
SIRDPCCHInitialDCH64 (UL SIR target without HS-DPCCH - DPDCH SF
64). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2984
SIRDPCCHInitialDCH8 (UL SIR target without HS-DPCCH and DPDCH
SF 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2985
SIRDPCCHInitialDCHHS128 (UL SIR target with HS-DPCCH - DPDCH SF
128). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2986
SIRDPCCHInitialDCHHS16 (UL SIR target with HS-DPCCH - DPDCH SF
16). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2987
SIRDPCCHInitialDCHHS256 (UL SIR target with HS-DPCCH - DPDCH SF
256). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2988
SIRDPCCHInitialDCHHS32 (UL SIR target with HS-DPCCH - DPDCH SF
32). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2989
SIRDPCCHInitialDCHHS4 (UL SIR target with HS-DPCCH - DPDCH SF 4)
2990
SIRDPCCHInitialDCHHS64 (UL SIR target with HS-DPCCH - DPDCH SF
64). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2991
SIRDPCCHInitialDCHHS8 (UL SIR target with HS-DPCCH - DPDCH SF 8)
2992
SIRDPCCHInitialDCHMax (Maximum SIR target for UL DPCCH with DPDCH only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2993
SIRDPCCHInitialDCHMin (Minimum SIR target for UL DPCCH with DPDCH only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2994
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
40.25.17
40.27
40.28
SIRDPCCHInitialDCHOffset (SIR target for UL outerloop power control
with DPDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2995
SIRDPCCHInitialDCHPSConvSpe (UL SIR target regardless of DL channel - PS conv speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2996
SIRDPCCHInitialDCHRxDiv2 (SIR target for UL DPCCH with DPDCH, 2way Rx diversity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2997
SIRDPCCHInitialDCHRxDiv4 (SIR target for UL DPCCH with DPDCH, 4way Rx diversity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2998
SIRDPCCHInitialEDCH (Initial SIR target for UL DPCCH with E-DCH) . .
3000
SIRDPCCHInitialEDCHPTT10MS (Initial SIR target for UL DPCCH with ETTI 10 ms - PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3001
SIRDPCCHInitialEDCHPTT2MS (Initial SIR target for UL DPCCH with ETTI 2 ms - PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3002
WRABChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 3003
WRABId (WRAB Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3004
41
41.1
41.2
41.2.1
41.2.2
41.2.3
41.3
41.4
41.5
41.6
WSG Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3006
GSMRoaming (GSM Roaming allowed) . . . . . . . . . . . . . . . . . . . . . . 3006
HomePLMN (Subscriber Home PLMN) . . . . . . . . . . . . . . . . . . . . . . . 3006
HomePlmnMCC (Home PLMN Mobile Country Code) . . . . . . . . . . . 3007
HomePlmnMNC (Home PLMN Mobile Network Code) . . . . . . . . . . . 3008
HomePlmnMNCLength (Home PLMN Mobile Network Code Length) 3009
OperatorName (Name of the subscriber home PLMN) . . . . . . . . . . . 3010
SubscriberGroupId (Subscriber Group Identifier) . . . . . . . . . . . . . . . 3011
WSGAuthorisedNetworkId (Identifier of the Authorised Network) . . . 3011
WSGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 3012
42
42.1
42.2
42.3
42.3.1
42.3.2
42.3.3
42.3.4
42.3.5
WSMLC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3014
CiPosCalcInSAS (Cell-ID based Position Calculation in SAS) . . . . . 3014
ConfAreaLevel (Confidence Area Level) . . . . . . . . . . . . . . . . . . . . . . 3015
EmergencyShapeList (Shape Priority List for Emergency Calls). . . . 3016
EmArc (Arc Priority for Emergency Calls) . . . . . . . . . . . . . . . . . . . . . 3017
EmPoint (Point Priority for Emergency Calls) . . . . . . . . . . . . . . . . . . 3018
EmPointAndAlt (Point And Altitude Priority for Emergency Calls) . . . 3020
EmPointAndCircle (Point And Circle Priority For Emergency Calls) . 3021
EmPointAndEll3D (3D Point And Ellipse Priority For Emergency Calls) . .
3023
EmPointAndEllipse (Point And Ellipse Priority For Emergency Calls) 3024
EmPolygon (Polygon Priority for Emergency Calls). . . . . . . . . . . . . . 3026
LCSCapacityUsage (LCS Capacity Usage). . . . . . . . . . . . . . . . . . . . 3028
LCSInterfaceOption (LCS Interface option) . . . . . . . . . . . . . . . . . . . . 3029
LCSShapeConversion (LCS Shape Conversion) . . . . . . . . . . . . . . . 3030
NetworkBasedAGPS (Network based A-GPS) . . . . . . . . . . . . . . . . . 3030
NetworkIndicatorForSAS (Network indicator for SAS). . . . . . . . . . . . 3031
OperationalMode (SMLC Operational Mode) . . . . . . . . . . . . . . . . . . 3032
PartialAGPSDataDelivery (Partial A-GPS data delivery) . . . . . . . . . . 3033
PeriodicalReportingCapacityUsage (PeriodicalReportingCapacityUsage)
3035
PreferredAGPSMethod (Preferred A-GPS method) . . . . . . . . . . . . . 3035
40.25.18
40.25.19
40.25.20
40.26
40.26.1
40.26.2
42.3.6
42.3.7
42.4
42.5
42.6
42.7
42.8
42.9
42.10
42.11
42.12
DN70456011
Id:0900d80580931b1d
Confidential
69
Radio Network Parameters in Flexi Direct
42.13
42.14
42.15
42.15.1
42.15.2
42.15.3
42.15.4
42.15.5
42.15.6
42.15.7
42.16
42.17
42.18
42.19
70
RNCDelayTolRespTime (Location Reporting Delay Tolerant response
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3037
RNCLowDelayResponseTime (Location Reporting Low Delay Response
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3038
ShapeList (Shape Priority List for Non-Emergency Calls) . . . . . . . . . 3039
Arc (Arc Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3040
Point (Point Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3041
PointAndAlt (Point And Altitude Priority) . . . . . . . . . . . . . . . . . . . . . . . 3043
PointAndCircle (Point And Uncertainty Circle Priority) . . . . . . . . . . . . 3044
PointAndEll3D (3D Point And Ellipse Priority) . . . . . . . . . . . . . . . . . . 3046
PointAndEllipse (Point And Uncertainty Ellipse Priority). . . . . . . . . . . 3047
Polygon (Polygon Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3049
SignallingPointCodeOfSAS (Signalling Point Code of SAS). . . . . . . . 3050
UEBasedAGPS (UE based A-GPS) . . . . . . . . . . . . . . . . . . . . . . . . . . 3051
WSMLCChangeOrigin (Change origin). . . . . . . . . . . . . . . . . . . . . . . . 3052
WSMLCid (WSMLC Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3053
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
List of tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Table 27
Table 28
Table 29
Table 30
Table 31
Table 32
Table 33
Table 34
Table 35
Table 36
Table 37
Table 38
Table 39
Table 40
Table 41
Table 42
Table 43
DN70456011
ADJDChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 387
ADJDId (Identifier of additional intra-frequency adjacency) . . . . . . . . 388
AdjdCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
AdjdCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . 389
AdjdDERR (Disable Effect on Reporting Range) . . . . . . . . . . . . . . . . 390
AdjdHSDPAHopsId (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . . . 391
AdjdLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
AdjdMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
AdjdMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
AdjdMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . 395
AdjdNRTHopsId (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 396
AdjdRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
AdjdRNCId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
AdjdRTHopsId (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 399
AdjdRTWithHSDPAHopsId (HSDPA HOPS identifier for speech services)
400
AdjdSRBHopsId (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 401
AdjdScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . 402
AdjdTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
ADJGBlindHO (ADJG Blind Handover to GSM/GPRS) . . . . . . . . . . . 405
ADJGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 406
ADJGId (Inter-system adjacency identifier) . . . . . . . . . . . . . . . . . . . . 407
ADJGType (Inter-system Neighbour Cell Type) . . . . . . . . . . . . . . . . . 408
AdjgBCC (Base Station Colour Code) . . . . . . . . . . . . . . . . . . . . . . . . 409
AdjgBCCH (BCCH ARFCN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
AdjgBandIndicator (Band Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . 411
AdjgCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
AdjgLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
AdjgMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
AdjgMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
AdjgMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . 416
AdjgNCC (Network Colour Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
AdjgSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . 417
AdjgTxPwrMaxRACH (Maximum UE TX Power on RACH) . . . . . . . . 421
AdjgTxPwrMaxTCH (Maximum UE TX Power on TCH) . . . . . . . . . . . 422
NrtHopgIdentifier (NRT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . 423
RtHopgIdentifier (RT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 424
ADJIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 426
ADJIId (Inter-frequency adjacency identifier) . . . . . . . . . . . . . . . . . . . 427
AdjiCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
AdjiCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . 428
AdjiComLoadMeasDRNCCellNCHO (NCHO activity of common load measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
AdjiEcNoOffsetNCHO (CPICH EcNo offset for the non-critical HO
procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
AdjiHandlingBlockedCellSLHO (Handling of blocked IF neighbour cell in
Id:0900d80580931b1d
Confidential
71
Radio Network Parameters in Flexi Direct
Table 44
Table 45
Table 46
Table 47
Table 48
Table 49
Table 50
Table 51
Table 52
Table 53
Table 54
Table 55
Table 56
Table 57
Table 58
Table 59
Table 60
Table 61
Table 62
Table 63
Table 64
Table 65
Table 66
Table 67
Table 68
Table 69
Table 70
Table 71
Table 72
Table 73
Table 74
Table 75
Table 76
Table 77
Table 78
Table 79
Table 80
Table 81
Table 82
Table 83
Table 84
Table 85
Table 86
Table 87
72
SLHO procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
AdjiLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434
AdjiMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435
AdjiMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
AdjiMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 437
AdjiNCHOHSPASupport (ADJI HSPA Cell for Non Critical Handover) . .
438
AdjiRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
AdjiRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
AdjiSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 441
AdjiScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . . 443
AdjiTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444
AdjiTxPwrDPCH (Maximum UE TX Power on DPCH) . . . . . . . . . . . . . 445
AdjiTxPwrRACH (Maximum UE TX Power on RACH) . . . . . . . . . . . . . 447
AdjiUARFCN (UTRA Absolute Radio Frequency Channel Number) . . 448
BlindHOTargetCell (Blind HO target cell) . . . . . . . . . . . . . . . . . . . . . . . 450
NrtHopiIdentifier (NRT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 451
RtHopiIdentifier (RT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 452
ADJLChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 454
ADJLId (Identifier of inter- system adjacency to LTE) . . . . . . . . . . . . . 455
AdjLEARFCN (E-UTRA Absolute Radio Frequency Channel Number) . . .
456
AdjLMeasBw (Measurement Bandwidth) . . . . . . . . . . . . . . . . . . . . . . . 457
HopLIdentifier (HOPL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
ADJSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 459
ADJSId (Intra-frequency adjacency identifier) . . . . . . . . . . . . . . . . . . . 460
AdjsCI (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
AdjsCPICHTxPwr (Primary CPICH power) . . . . . . . . . . . . . . . . . . . . . 461
AdjsDERR (Disable Effect on Reporting Range) . . . . . . . . . . . . . . . . . 462
AdjsEcNoOffset (CPICH Ec/No Offset) . . . . . . . . . . . . . . . . . . . . . . . . 463
AdjsLAC (Location Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
AdjsMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
AdjsMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466
AdjsMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . 467
AdjsRAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
AdjsRNCid (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
AdjsSIB (Include in System Information) . . . . . . . . . . . . . . . . . . . . . . . 470
AdjsScrCode (Primary Scrambling Code) . . . . . . . . . . . . . . . . . . . . . . 472
AdjsTxDiv (Tx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
AdjsTxPwrRACH (Maximum UE TX Power on RACH) . . . . . . . . . . . . 474
HSDPAHopsIdentifier (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . . 475
NrtHopsIdentifier (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 476
RTWithHSDPAHopsIdentifier (HSDPA HOPS identifier for
speechservices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
RtHopsIdentifier (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 479
SRBHopsIdentifier (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . 479
CBCIChangeOrigin (CBCI Change Origin) . . . . . . . . . . . . . . . . . . . . . 481
CBCIId (CBCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 88
Table 89
Table 90
Table 91
Table 92
Table 93
Table 94
Table 95
Table 96
Table 97
Table 98
Table 99
Table 100
Table 101
Table 102
Table 103
Table 104
Table 105
Table 106
Table 107
Table 108
Table 109
Table 110
Table 111
Table 112
Table 113
Table 114
Table 115
Table 116
Table 117
Table 118
Table 119
Table 120
Table 121
Table 122
Table 123
Table 124
Table 125
Table 126
Table 127
Table 128
Table 129
DN70456011
CBCIPaddrType (Type of CBC IP address) . . . . . . . . . . . . . . . . . . . . 483
CBCIPaddress (IP address of the CBC) . . . . . . . . . . . . . . . . . . . . . . . 483
ETWSsupportEnabled (ETWS Support Enabled) . . . . . . . . . . . . . . . . 484
IUOIdentifier (IUO Object Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 485
ACBarredListSystem (Access Class Barred List given by System) . . 487
CMOBChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 489
CMOBId (Congestion Management Group Identifier) . . . . . . . . . . . . . 490
CellAccessRestriction (Cell Access Restriction) . . . . . . . . . . . . . . . . . 491
RestrictionGroupName (Restriction group name) . . . . . . . . . . . . . . . . 492
RestrictionGroupType (Restriction group type) . . . . . . . . . . . . . . . . . . 493
TrafficRestriction (Traffic Restriction) . . . . . . . . . . . . . . . . . . . . . . . . . 494
AMRDirReCell (Usage of Directed Retry of AMR call Inter-system
Handov) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
BLHOFailIRCellPenalty (BLHO failure inter-system cell penalty) . . . . 496
DLDPCHTxPwrClOffset (DL DPCH Transmission Power Cancellation
Offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
FMCGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 498
FMCGId (FMCG identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499
GSMcauseCPICHEcNo (GSM HO caused by CPICH Ec/No) . . . . . . 500
GSMcauseCPICHrscp (GSM HO caused by CPICH RSCP) . . . . . . . 501
GSMcauseTxPwrDL (GSM HO caused by DL DPCH TX Power) . . . 503
GSMcauseTxPwrUL (GSM HO caused by UE TX Power) . . . . . . . . . 504
GSMcauseUplinkQuality (GSM HO caused by UL DCH Quality) . . . . 506
GsmDLTxPwrThrAMR (DL DPCH TX Power Threshold for AMR) . . . 507
GsmDLTxPwrThrCS (DL DPCH TX Power Threshold for CS) . . . . . . 508
GsmDLTxPwrThrNrtPS (DL DPCH TX Power Threshold for NRT PS) 509
GsmDLTxPwrThrRtPS (DL DPCH TX Power Threshold for RT PS) . 510
GsmMaxMeasPeriod (Maximum Measurement Period) . . . . . . . . . . . 511
GsmMeasAveWindow (Measurement Averaging Window) . . . . . . . . 512
GsmMeasRepInterval (Measurement Reporting Interval) . . . . . . . . . 513
GsmMinHoInterval (Minimum Interval Between HOs) . . . . . . . . . . . . 514
GsmMinMeasInterval (Minimum Measurement Interval) . . . . . . . . . . 515
GsmMinSLHOInterval (Minimum interval between repetitive inter-RAT
SLHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
GsmNcellSearchPeriod (GSM Neighbour Cell Search Period) . . . . . 517
GsmUETxPwrFilterCoeff (UE TX Power Filter Coefficient) . . . . . . . . 518
GsmUETxPwrThrAMR (UE TX Power Threshold for AMR) . . . . . . . . 519
GsmUETxPwrThrCS (UE TX Power Threshold for CS) . . . . . . . . . . . 520
GsmUETxPwrThrNrtPS (UE TX Power Threshold for NRT PS) . . . . . 521
GsmUETxPwrThrRtPS (UE TX Power Threshold for RT PS) . . . . . . 522
GsmUETxPwrTimeHyst (UE TX Power Time Hysteresis) . . . . . . . . . 523
IMSIbasedGsmHo (IMSI Based GSM HO) . . . . . . . . . . . . . . . . . . . . . 525
ISHOClcauseCPICHEcNo (ISHO Cancellation caused by CPICH Ec/No)
526
ISHOClcauseCPICHrscp (ISHO Cancellation caused by CPICH RSCP) .
527
ISHOClcauseTxPwrDL (ISHO Cancellation caused by DL DPCH TX
Power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528
Id:0900d80580931b1d
Confidential
73
Radio Network Parameters in Flexi Direct
Table 130
Table 131
Table 132
Table 133
Table 134
Table 135
Table 136
Table 137
Table 138
Table 139
Table 140
Table 141
Table 142
Table 143
Table 144
Table 145
Table 146
Table 147
Table 148
Table 149
Table 150
Table 151
Table 152
Table 153
Table 154
Table 155
Table 156
Table 157
Table 158
Table 159
Table 160
Table 161
Table 162
Table 163
Table 164
Table 165
Table 166
Table 167
Table 168
Table 169
Table 170
Table 171
Table 172
Table 173
Table 174
74
ISHOClcauseTxPwrUL (ISHO Cancellation caused by UE TX Power) 529
MaxBSICIdentTime (Maximum BSIC Identification Time) . . . . . . . . . . 530
FMCIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 532
FMCIId (FMCI identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533
IFHOcauseCPICHEcNo (IFHO caused by CPICH Ec/No) . . . . . . . . . 534
IFHOcauseCPICHrscp (IFHO caused by CPICH RSCP) . . . . . . . . . . 535
IFHOcauseTxPwrDL (IFHO caused by DL DPCH TX Power) . . . . . . . 537
IFHOcauseTxPwrUL (IFHO caused by UE TX Power) . . . . . . . . . . . . 539
IFHOcauseUplinkQuality (IFHO caused by UL DCH Quality) . . . . . . . 541
IMSIbasedIFHO (IMSI Based IFHO) . . . . . . . . . . . . . . . . . . . . . . . . . . 542
InterFreqDLTxPwrThrAMR (DL DPCH TX Power Threshold for AMR) 543
InterFreqDLTxPwrThrCS (DL DPCH TX Power Threshold for CS) . . . 544
InterFreqDLTxPwrThrNrtPS (DL DPCH TX Power Threshold for NRT PS)
545
InterFreqDLTxPwrThrRtPS (DL DPCH TX Power Threshold for RT PS) .
546
InterFreqMaxMeasPeriod (Maximum Measurement Period) . . . . . . . . 547
InterFreqMeasAveWindow (Measurement Averaging Window) . . . . . 548
InterFreqMeasRepInterval (Measurement Reporting Interval) . . . . . . 549
InterFreqMinHoInterval (Minimum Interval Between HOs) . . . . . . . . . 550
InterFreqMinMeasInterval (Minimum Measurement Interval) . . . . . . . 550
InterFreqMinSLHOInterval (Minimum interval between repetitive IF
SLHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
InterFreqNcellSearchPeriod (Neighbour Cell Search Period) . . . . . . . 552
InterFreqUETxPwrFilterCoeff (UE TX Power Filter Coefficient) . . . . . 553
InterFreqUETxPwrThrAMR (UE TX Power Threshold for AMR) . . . . . 555
InterFreqUETxPwrThrCS (UE TX Power Threshold for CS) . . . . . . . . 556
InterFreqUETxPwrThrNrtPS (UE TX Power Threshold for NRT PS) . . 557
InterFreqUETxPwrThrRtPS (UE TX Power Threshold for RT PS) . . . 558
InterFreqUETxPwrTimeHyst (UE TX Power Time Hysteresis) . . . . . . 559
MBLBMobilityOffset (MBLB due to Mobility EcNo Offset) . . . . . . . . . . 560
MBLBMobilityRABComb (MBLB due to Mobility RAB Combinations) . 562
ActiveSetWeightingCoefficient (Active Set Weighting Coefficient) . . . 563
AdditionReportingInterval (Addition Reporting Interval) . . . . . . . . . . . . 564
AdditionTime (Addition Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
AdditionWindow (Addition Window) . . . . . . . . . . . . . . . . . . . . . . . . . . . 567
DSRepBasedSHO (Detected Set Reporting Based SHO) . . . . . . . . . . 568
DropReportingInterval (Drop Reporting Interval) . . . . . . . . . . . . . . . . . 570
DropTime (Drop Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 571
DropWindow (Drop Window) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573
EDCHAddEcNoOffset (Allow E-DCH usage EcNo offset) . . . . . . . . . . 574
EDCHRemEcNoOffset (CPICH EcNo offset E-DCH usage removal) . 575
EcNoFilterCoefficient (CPICH Ec/No Filter Coefficient) . . . . . . . . . . . . 576
FMCSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 578
FMCSId (FMCS identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579
HHoEcNoCancel (CPICH Ec/No HHO Cancellation) . . . . . . . . . . . . . . 580
HHoEcNoCancelTime (CPICH Ec/No HHO Cancellation Time) . . . . . 581
HHoEcNoThreshold (CPICH Ec/No HHO Threshold) . . . . . . . . . . . . . 584
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 175
Table 176
Table 177
Table 178
Table 179
Table 180
Table 181
Table 182
Table 183
Table 184
Table 185
Table 186
Table 187
Table 188
Table 189
Table 190
Table 191
Table 192
Table 193
Table 194
Table 195
Table 196
Table 197
Table 198
Table 199
Table 200
Table 201
Table 202
Table 203
Table 204
Table 205
Table 206
Table 207
Table 208
Table 209
Table 210
Table 211
Table 212
Table 213
Table 214
Table 215
Table 216
Table 217
DN70456011
HHoEcNoTimeHysteresis (CPICH Ec/No HHO Time Hysteresis) . . . 585
HHoRscpCancel (CPICH RSCP HHO Cancellation) . . . . . . . . . . . . . 587
HHoRscpCancelTime (CPICH RSCP HHO Cancellation Time) . . . . . 589
HHoRscpFilterCoefficient (CPICH RSCP HHO Filter Coefficient) . . . 592
HHoRscpThreshold (CPICH RSCP HHO Threshold) . . . . . . . . . . . . . 593
HHoRscpTimeHysteresis (CPICH RSCP HHO Time Hysteresis) . . . 594
IMSIbasedSHO (IMSI Based SHO) . . . . . . . . . . . . . . . . . . . . . . . . . . 596
MaxActiveSetSize (Maximum Active Set Size) . . . . . . . . . . . . . . . . . . 597
ReplacementReportingInterval (Replacement Reporting Interval) . . . 599
ReplacementTime (Replacement Time) . . . . . . . . . . . . . . . . . . . . . . . 600
ReplacementWindow (Replacement Window) . . . . . . . . . . . . . . . . . . 602
AdjgHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . 604
AdjgHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . 605
AdjgMinRxLevNCHO (Minimum RX level for non-critical HO) . . . . . . 606
AdjgPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . 607
AdjgPenaltyTimeNCHO (Penalty time for GSM cell in non-critical HO) . .
607
AdjgPriorityCoverage (Ncell Priority for Coverage HO) . . . . . . . . . . . 608
AdjgPrioritySLHO (Neighbour cell priority for SLHO) . . . . . . . . . . . . . 609
AdjgQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . 610
AdjgQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . 611
AdjgRxLevMinHO (Minimum RX Level for Coverage HO) . . . . . . . . . 612
AdjgTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . 613
HOPGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 615
HOPGId (HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616
AdjiEcNoMargin (CPICH Ec/No Margin for IFHO) . . . . . . . . . . . . . . . 618
AdjiHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . 619
AdjiHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . 620
AdjiMinEcNo (Minimum CPICH Ec/No for IFHO) . . . . . . . . . . . . . . . . 621
AdjiMinEcNoNCHO (Minimum CPICH Ec/No for non-critical IFHO) . . 622
AdjiMinRSCP (Minimum CPICH RSCP for IFHO) . . . . . . . . . . . . . . . 623
AdjiMinRscpNCHO (Minimum CPICH RSCP for non-critical IFHO) . . 623
AdjiPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . 624
AdjiPenaltyTimeNCHO (Penalty time for WCDMA cell in non-critical HO)
625
AdjiPlossMargin (Pathloss Margin for IFHO) . . . . . . . . . . . . . . . . . . . 626
AdjiPriorityCoverage (Ncell Priority for Coverage IFHO) . . . . . . . . . . 627
AdjiPriorityDCellCAHO (Neighbour cell priority for DC HSDPA Capa Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 628
AdjiPriorityHSCAHO (Neighbour Cell Priority for HSPA Capability Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630
AdjiPriorityMIMOCAHO (Neighbour cell priority for MIMO Capa Based
HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631
AdjiPriorityQuality (Ncell Priority for Quality IFHO) . . . . . . . . . . . . . . . 632
AdjiPrioritySLHO (Neighbour cell priority for service and load IFHO) . 633
AdjiQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . 634
AdjiQoffset2 (Cell Re-selection Quality Offset 2) . . . . . . . . . . . . . . . . 635
AdjiQqualMin (Cell Re-selection Minimum Quality) . . . . . . . . . . . . . . 636
Id:0900d80580931b1d
Confidential
75
Radio Network Parameters in Flexi Direct
Table 218
Table 219
Table 220
Table 221
Table 222
Table 223
Table 224
Table 225
Table 226
Table 227
Table 228
Table 229
Table 230
Table 231
Table 232
Table 233
Table 234
Table 235
Table 236
Table 237
Table 238
Table 239
Table 240
Table 241
Table 242
Table 243
Table 244
Table 245
Table 246
Table 247
Table 248
Table 249
Table 250
Table 251
Table 252
Table 253
Table 254
Table 255
Table 256
Table 257
Table 258
Table 259
Table 260
Table 261
Table 262
76
AdjiQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . . 637
AdjiTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . . 638
AdjiTempOffset2 (Cell Re-selection Temporary Offset 2) . . . . . . . . . . 639
BlindHORSCPThr (Blind HO RSCP threshold) . . . . . . . . . . . . . . . . . . 640
HOPIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 641
HOPIId (HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642
AdjLAbsPrioCellReselec (Cell Reselection Absolute Priority) . . . . . . . 644
AdjLQrxlevminEUTRA (Cell Reselection Minimum RX level) . . . . . . . 645
AdjLThreshigh (Cell Reselection Threshold high) . . . . . . . . . . . . . . . . 645
AdjLThreslow (Cell Reselection Threshold low) . . . . . . . . . . . . . . . . . 646
HOPLChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 647
HOPLId (HOPL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 648
AdjsHCSpriority (Cell Re-selection HCS Priority) . . . . . . . . . . . . . . . . 650
AdjsHCSthreshold (Cell Re-selection HCS Threshold) . . . . . . . . . . . . 651
AdjsPenaltyTime (Cell Re-selection Penalty Time) . . . . . . . . . . . . . . . 652
AdjsQoffset1 (Cell Re-selection Quality Offset 1) . . . . . . . . . . . . . . . . 653
AdjsQoffset2 (Cell Re-selection Quality Offset 2) . . . . . . . . . . . . . . . . 654
AdjsQqualMin (Cell Re-selection Minimum Quality) . . . . . . . . . . . . . . 655
AdjsQrxlevMin (Cell Re-selection Minimum RX Level) . . . . . . . . . . . . 655
AdjsTempOffset1 (Cell Re-selection Temporary Offset 1) . . . . . . . . . . 656
AdjsTempOffset2 (Cell Re-selection Temporary Offset 2) . . . . . . . . . . 658
EcNoAveragingWindow (CPICH Ec/No Averaging Window) . . . . . . . . 659
EnableInterRNCsho (Enable Inter-RNC Soft Handover) . . . . . . . . . . . 660
EnableRRCRelease (Enable RRC Connection Release) . . . . . . . . . . 661
HHOMarginAverageEcNo (HHO Margin for Average Ec/No) . . . . . . . 662
HHOMarginPeakEcNo (HHO Margin for Peak Ec/No) . . . . . . . . . . . . 663
HOPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 664
HOPSId (HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665
HSDPAAvailabilityIur (HSDPA availability of the neighbouring DRNC cell)
666
HSUPAAvailabilityIur (HSUPA availability of the neighbouring DRNC cell)
667
ReleaseMarginAverageEcNo (Release Margin for Average Ec/No) . . 668
ReleaseMarginPeakEcNo (Release Margin for Peak Ec/No) . . . . . . . 669
AlarmSetforWCELBLINIT (Alarm Set for WCEL BL-INIT) . . . . . . . . . . 671
CBCSourceIPAddress (Source IP address for IuBC interface) . . . . . . 672
CSAttachDetachAllowed (Attach-detach allowed) . . . . . . . . . . . . . . . . 672
CommonMCC (Common MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674
CommonMNC (Common MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675
CommonMNCLength (Common MNC Length) . . . . . . . . . . . . . . . . . . 676
ConnectionRetryCounter (OAM Connection Establishment Retry Counter)
677
DSCPStatisticsGroupA (DSCP statistics group A ) . . . . . . . . . . . . . . . 678
DSCPStatisticsGroupB (DSCP statistics group B) . . . . . . . . . . . . . . . 679
DSCPStatisticsGroupC (DSCP statistics group C) . . . . . . . . . . . . . . . 680
DSCPStatisticsGroupTCPack (DSCP code for DL TCP Ack statistics) 682
EmergencyCallRedirectTimer (Emergency Call Redirect Timer) . . . . . 683
ExtendedULDLactivationTmr (Extended Cell_FACH inactivity supervision
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 263
Table 264
Table 265
Table 266
Table 267
Table 268
Table 269
Table 270
Table 271
Table 272
Table 273
Table 274
Table 275
Table 276
Table 277
Table 278
Table 279
Table 280
Table 281
Table 282
Table 283
Table 284
Table 285
Table 286
Table 287
Table 288
Table 289
Table 290
Table 291
Table 292
Table 293
Table 294
Table 295
Table 296
Table 297
Table 298
Table 299
Table 300
Table 301
Table 302
Table 303
Table 304
Table 305
Table 306
DN70456011
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
IASCCRepTimer (Inter-Adapter SCC repetition timer) . . . . . . . . . . . . 685
LCSSupportForAnchoring (LCS Support for Anchoring) . . . . . . . . . . 685
LCSfunctionality (LCS functionality) . . . . . . . . . . . . . . . . . . . . . . . . . . 687
MACLogicalChPriority (MAC logical channel priority definition) . . . . . 687
MACLogChPriSRB1 (MAC logical channel priority for SRB1) . . . . . . 689
MACLogChPriSRB2 (MAC logical channel priority for SRB2) . . . . . . 689
MACLogChPriSRB3 (MAC logical channel priority for SRB3) . . . . . . 690
N302 (N302) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
N304 (N304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 692
N308 (N308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693
OMSBackupIpAddress (OMS Backup IP Address) . . . . . . . . . . . . . . 694
OMSIpAddress (OMS IP Address) . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
PWSMDuration (Duration of low traffic for cell shutdown) . . . . . . . . . 695
PWSMExceededTrafficDur (Time limit for traffic to activate a shutdown
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696
PageRep1stInterv (Repetition interval of the first repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697
PageRep2ndInterv (Repetition interval of the second repeated connected
mode paging procedure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 699
RANAPprocInitWait (RANAP initiation timer) . . . . . . . . . . . . . . . . . . . 700
RNCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 701
RNCIPAddress (RNC IP-address) . . . . . . . . . . . . . . . . . . . . . . . . . . . 703
RNCName (RNC name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703
RTservicesForPS (PS domain RT service) . . . . . . . . . . . . . . . . . . . . . 704
RestrictionInterval (Restriction Interval) . . . . . . . . . . . . . . . . . . . . . . . 705
RncClientTLSMode (RNC Client TLS Mode) . . . . . . . . . . . . . . . . . . . 707
RncId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 708
SIB11_priority (Priority for SIB11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709
SIB15_priority (Priority for SIB15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
SIB18_priority (Priority for SIB18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711
SIB19Priority (Priority for SIB19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711
SIB1_priority (Priority for SIB1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712
SIB2_priority (Priority for SIB2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 713
SIB3_priority (Priority for SIB3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 714
SIB5_priority (Priority for SIB5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715
SecOMSIpAddress (Secondary OMS IP address) . . . . . . . . . . . . . . . 716
ServingOMS (Serving OMS ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717
ServingOMSAdminSetting (Serving OMS Admin Setting) . . . . . . . . . 718
ServingOMSSwoRequest (Serving OMS Switchover Request) . . . . . 720
T302 (T302) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721
T304 (T304) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 722
T305 (T305) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
T307 (T307) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724
T308 (T308) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725
T309 (T309) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 726
T314 (T314) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727
T316 (T316) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 729
Id:0900d80580931b1d
Confidential
77
Radio Network Parameters in Flexi Direct
Table 307
Table 308
Table 309
Table 310
Table 311
Table 312
Table 313
Table 314
Table 315
Table 316
Table 317
Table 318
Table 319
Table 320
Table 321
Table 322
Table 323
Table 324
Table 325
Table 326
Table 327
Table 328
Table 329
Table 330
Table 331
Table 332
Table 333
Table 334
Table 335
Table 336
Table 337
Table 338
Table 339
78
T317 (T317) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 730
ToAWE_NRT_DCH_tti10 (Time of Arrival Window Endpoint for NRT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 731
ToAWE_NRT_DCH_tti20 (Time of Arrival Window Endpoint for NRT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 732
ToAWE_NRT_DCH_tti40 (Time of Arrival Window Endpoint for NRT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733
ToAWE_RT_DCH_tti10 (Time of Arrival Window Endpoint for RT DCH (TTI
10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 734
ToAWE_RT_DCH_tti20 (Time of Arrival Window Endpoint for RT DCH (TTI
20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 735
ToAWE_RT_DCH_tti40 (Time of Arrival Window Endpoint for RT DCH (TTI
40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 736
ToAWE_Speech (Time of Arrival Window Endpoint for speech services) .
737
ToAWS_NRT_DCH_tti10 (Time of Arrival Window Startpoint for NRT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
ToAWS_NRT_DCH_tti20 (Time of Arrival Window Startpoint for NRT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
ToAWS_NRT_DCH_tti40 (Time of Arrival Window Startpoint for NRT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 740
ToAWS_RT_DCH_tti10 (Time of Arrival Window Startpoint for RT DCH
(TTI 10)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 741
ToAWS_RT_DCH_tti20 (Time of Arrival Window Startpoint for RT DCH
(TTI 20)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 742
ToAWS_RT_DCH_tti40 (Time of Arrival Window Startpoint for RT DCH
(TTI 40)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743
ToAWS_Speech (Time of Arrival Window Startpoint for speech services)
744
TraceLCSHorizAccur (Trace LCS Horizontal Accuracy) . . . . . . . . . . . 745
TraceLCSPriority (Trace LCS Priority) . . . . . . . . . . . . . . . . . . . . . . . . . 746
TraceLCSVertAccur (Trace LCS Vertical Accuracy) . . . . . . . . . . . . . . 747
TraceLCSWaitPeriod (Trace LCS Wait Period) . . . . . . . . . . . . . . . . . . 748
UL_DLcapacityReqWait (Waiting time for UL/DL capacity request) . . 749
WCELIdleAlarmTimeout (WCEL Idle Alarm Timeout) . . . . . . . . . . . . . 751
IPNBId (IPNB object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 752
NodeBIPAddress (Control Plane Destination Address Iub) . . . . . . . . . 752
SourceNBAPIPAddress (Iub control plane source IP address) . . . . . . 753
SourceNBAPIPNetmask (Iub control plane source IP netmask) . . . . . 755
BackgroundTCToDSCP (Background TC to DSCP mapping) . . . . . . . 757
ConversationalTCToDSCP (Conversational TC to DSCP mapping) . . 758
IPQMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 759
IPQMId (IP Qos Management Identifier) . . . . . . . . . . . . . . . . . . . . . . . 760
InteractiveTHP1TCToDSCP (Interactive THP1 TC to DSCP mapping) . .
761
InteractiveTHP2TCToDSCP (Interactive THP2 TC to DSCP mapping) . .
762
InteractiveTHP3TCToDSCP (Interactive THP3 TC to DSCP mapping) . .
763
StreamingTCToDSCP (Streaming TC to DSCP mapping) . . . . . . . . . 764
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 340
Table 341
Table 342
Table 343
Table 344
Table 345
Table 346
Table 347
Table 348
Table 349
Table 350
Table 351
Table 352
Table 353
Table 354
Table 355
Table 356
Table 357
Table 358
Table 359
Table 360
Table 361
Table 362
Table 363
Table 364
Table 365
Table 366
Table 367
Table 368
Table 369
Table 370
Table 371
Table 372
Table 373
Table 374
Table 375
Table 376
Table 377
Table 378
Table 379
Table 380
Table 381
Table 382
Table 383
Table 384
Table 385
DN70456011
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . 765
CNId (Core Network Identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 766
CSCNNRI (NRI for CS Core routing) . . . . . . . . . . . . . . . . . . . . . . . . . 767
NRIMaxForCSCN (Maximum value of NRI range for CS Core routing) . .
768
NRIMinForCSCN (Minimum value of NRI range for CS Core routing) 769
CSFlexiIuWeight (CS Flexible Iu Weight) . . . . . . . . . . . . . . . . . . . . . . 770
DefaultCN (Default Core Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . 771
IUCSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . 772
IUCSId (IuCS Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773
IUOIdentifier (IUO Object Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 774
IuState (State of Iu interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775
MinUDPPortCS (Minimum UDP Port) . . . . . . . . . . . . . . . . . . . . . . . . . 776
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 777
PagingOptSupport (Support of Paging Optimization Feature) . . . . . . 778
RelocationSupport (Serving RNC Relocation Support) . . . . . . . . . . . 779
RtcpActivation (RTCP activation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 780
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . 781
TRafC (TRafC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 782
TRatC (TRatC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 783
TigOR (TigOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 784
TinTR (TinTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 785
DestIPAddressCS (IP address for the IUCS destination subnet) . . . . 786
IPBasedRouteIdCS (IP Based Route Identifier for IUCS) . . . . . . . . . . 787
IPNetmaskCS (IP netmask for the IUCS destination subnet) . . . . . . . 788
IPQMIdCS (IPQM object id for IuCS) . . . . . . . . . . . . . . . . . . . . . . . . . 790
IUCSIPChangeOrigin (IUCSIP Change Origin) . . . . . . . . . . . . . . . . . 791
IUCSIPId (IUCSIP Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 792
CSCNDRXLength (CN CS domain specific DRX cycle length) . . . . . 794
CS_T3212 (T3212) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 795
IUOChangeOrigin (IUO Change Origin) . . . . . . . . . . . . . . . . . . . . . . . 796
IUOId (IUO Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 797
IuBarringDelayTimerCS (Iu Barring Delay Timer for CS) . . . . . . . . . . 798
IuBarringDelayTimerPS (Iu Barring Delay Timer for PS) . . . . . . . . . . 799
IuBarringRecoveryGroupCS (Iu Barring Recovery Group for CS) . . . 800
IuBarringRecoveryGroupPS (Iu Barring Recovery Group for PS) . . . 801
IuBarringRecoveryTimerCS (Iu service barring recovery timer for CS) 802
IuBarringRecoveryTimerPS (Iu service barring recovery timer for PS) 803
NRILengthForCSCN (NRI length for CS Core Networks) . . . . . . . . . . 804
NRILengthForPSCN (NRI length for PS Core Networks) . . . . . . . . . . 805
NullNRIForCSPool (Null NRI value for CS Pool) . . . . . . . . . . . . . . . . 806
NullNRIForPSPool (Null NRI value for PS Pool) . . . . . . . . . . . . . . . . . 807
OperatorWeight (Operator Weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . 808
PLMNid (PLMN identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 809
MCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 810
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 811
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . 812
Id:0900d80580931b1d
Confidential
79
Radio Network Parameters in Flexi Direct
Table 386
Table 387
Table 388
Table 389
Table 390
Table 391
Table 392
Table 393
Table 394
Table 395
Table 396
Table 397
Table 398
Table 399
Table 400
Table 401
Table 402
Table 403
Table 404
Table 405
Table 406
Table 407
Table 408
Table 409
Table 410
Table 411
Table 412
Table 413
Table 414
Table 415
Table 416
Table 417
Table 418
Table 419
Table 420
Table 421
Table 422
Table 423
Table 424
Table 425
Table 426
Table 427
Table 428
80
PSCNDRXLength (CN PS domain specific DRX cycle length) . . . . . . 813
PS_NMO (Network Mode of Operation) . . . . . . . . . . . . . . . . . . . . . . . 815
SharedAreaPLMNid (Shared area PLMN identity) . . . . . . . . . . . . . . . 816
SharedAreaMCC (Shared area Mobile Country Code) . . . . . . . . . . . . 817
SharedAreaMNC (Shared area Mobile Network Code) . . . . . . . . . . . . 818
SharedAreaMNClength (Shared area Mobile Network Code Length) . 819
CNDomainVersion (Release version of Core Network) . . . . . . . . . . . . 821
CNId (Core Network Identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 822
CellFACHRelocSupport (Cell_FACH state Serving RNC Relocation Support ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 823
DefaultCN (Default Core Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 823
IUOIdentifier (IUO Object Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 825
IUPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 825
IUPSId (IuPS Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 827
IuState (State of Iu interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 827
NetworkInd (Network indicator) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 829
PSCNNRI (NRI for PS Core routing) . . . . . . . . . . . . . . . . . . . . . . . . . . 830
NRIMaxForPSCN (Maximum value of NRI range for PS Core routing) 831
NRIMinForPSCN (Minimum value of NRI range for PS Core routing) . 832
PSFlexiIuWeight (PS Flexible Iu Weight) . . . . . . . . . . . . . . . . . . . . . . . 833
PagingOptSupport (Support of Paging Optimization Feature) . . . . . . . 835
RelocationSupport (Serving RNC Relocation Support) . . . . . . . . . . . . 836
SignPointCode (Signalling point code) . . . . . . . . . . . . . . . . . . . . . . . . 836
TDataFwd (T DATAfwd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 838
TRafC (TRafC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 838
TRatC (TRatC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 839
TigOR (TigOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 840
TinTR (TinTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 841
DestIPAddressPS (IP address for the IUPS destination subnet) . . . . . 843
IPBasedRouteIdPS (IP Based Route Identifier for IUPS) . . . . . . . . . . 845
IPNetmaskPS (IP netmask for the IUPS destination subnet) . . . . . . . 846
IPQMIdPS (IPQM object id for IuPS) . . . . . . . . . . . . . . . . . . . . . . . . . . 848
IUPSIPChangeOrigin (IUPSIP Change Origin) . . . . . . . . . . . . . . . . . . 849
IUPSIPId (IUPSIP Identifier ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850
ADAURAId (FD-RNC neighboring Adapter shared URA identity) . . . . 852
AppAwareRANEnabled (Application Aware RAN Enabled) . . . . . . . . . 853
CellFACHnRncRelocSupport (Cell_FACH state Serving RNC Relocation
Support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 854
DSCPHighIur (DSCP high priority for Iur) . . . . . . . . . . . . . . . . . . . . . . 855
DSCPLowIur (Low priority DSCP for Iur) . . . . . . . . . . . . . . . . . . . . . . . 856
DSCPMedDCHIur (DSCP medium priority on R99 DCH for Iur) . . . . . 857
DelayThresholdMaxIur (Maximum Threshold for HSUPA congestion handling delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 858
DelayThresholdMidIur (Middle Threshold value for HSUPA congestion
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 859
DelayThresholdMinIur (Minimum Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 860
HSDPACCEnabledIur (HSDPA Congestion Control activation Iur) . . . 861
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 429
Table 430
Table 431
Table 432
Table 433
Table 434
Table 435
Table 436
Table 437
Table 438
Table 439
Table 440
Table 441
Table 442
Table 443
Table 444
Table 445
Table 446
Table 447
Table 448
Table 449
Table 450
Table 451
Table 452
Table 453
Table 454
Table 455
Table 456
Table 457
Table 458
Table 459
Table 460
Table 461
Table 462
Table 463
Table 464
Table 465
Table 466
Table 467
DN70456011
HSDPAULCToDSCPIur (HSDPA UL FP Control traffic to DSCP mapping
Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 862
HSPAOverIur (HSPA over Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 863
HSUPADLCToDSCPIur (HSUPA DL FP Control traffic to DSCP mapping
Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
IBTSSharing (IBTS Sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
IPBasedRouteIdIur (IP based route identifier) . . . . . . . . . . . . . . . . . . 866
IURChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 867
IURId (Iur Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 868
InterfaceMode (Configure the IUR in a special mode) . . . . . . . . . . . . 869
IurUPSupport (User Plane support of Iur connection) . . . . . . . . . . . . 870
MaxFPDLFrameSizeIur (Maximum FP downlink frame size Iur) . . . . 871
MaxIurNRTHSDSCHBitRate (Maximum NRT HS-DSCH MAC-d flow bit
rate over Iur) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872
MinUDPPortIur (Minimum UDP port value) . . . . . . . . . . . . . . . . . . . . 874
NRncId (Neighbour RNC identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 874
NRncNetworkInd (Network indicator of neighbour RNC) . . . . . . . . . . 876
NRncRelocationSupport (Serving RNC Relocation Support of neighbour
RNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 877
NRncSignPointCode (Signalling point code of neighbour RNC) . . . . . 878
NRncVersion (Release version of Neighbouring RNC) . . . . . . . . . . . 879
NeighbouringPLMNid (Neighbouring PLMN identity) . . . . . . . . . . . . . 880
MCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
MNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 882
MNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . . . . . . . 883
NeighbouringRNWElement (Type of the Neighbouring RNW Element) . .
884
OverbookingSwitchIur (Overbooking Switch Iur) . . . . . . . . . . . . . . . . 885
ProbabilityFactorMaxIur (ProbabilityFactor for Congestion Indication
sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886
RNSAPCongAndPreemption (RNSAP Congestion And Preemption) 887
ToAWEOffsetNRTDCHIP (ToAWE Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888
ToAWEOffsetRTDCHIP (ToAWE Offset for RT DCH connections over IP)
889
ToAWSOffsetNRTDCHIP (ToAWS Offset for NRT DCH connections over
IP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 890
ToAWSOffsetRTDCHIP (ToAWS Offset for RT DCH connections over IP)
891
AMRToNonPreferredLayer (AMR to Non Preferred Layer) . . . . . . . . 893
BlindHORSCPThrAbove (Blind HO RSCP threshold above) . . . . . . . 894
BlindHORSCPThrBelow (Blind HO RSCP threshold below) . . . . . . . 894
LaySelLowLoadPref (Layer Selection Low Load Preferred) . . . . . . . . 895
LaySelWeightBand (Layer Selection Weight of Band) . . . . . . . . . . . . 896
LaySelWeightLoad (Layer Selection Weight of Load) . . . . . . . . . . . . 897
LaySelWeightPrefLayer (Layer Selection Weight of Preferred Layer) 898
LaySelWeightRSCP (Layer Selection Weight of RSCP) . . . . . . . . . . 899
PFL64QAMAMR (Preferred Frequency Layer for 64QAM AMR) . . . . 900
PrefLayer64QAMAMR (Preferred Layer for 64QAM AMR) . . . . . . . . 901
Id:0900d80580931b1d
Confidential
81
Radio Network Parameters in Flexi Direct
Table 468
Table 469
Table 470
Table 471
Table 472
Table 473
Table 474
Table 475
Table 476
Table 477
Table 478
Table 479
Table 480
Table 481
Table 482
Table 483
Table 484
Table 485
Table 486
Table 487
Table 488
Table 489
Table 490
Table 491
Table 492
Table 493
Table 494
Table 495
Table 496
Table 497
Table 498
Table 499
Table 500
Table 501
82
PFL64QAMAMRNRT (Preferred Frequency Layer for 64QAM AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902
PrefLayer64QAMAMRNRT (Preferred Layer for 64QAM AMR and NRT) .
902
PFL64QAMNRT (Preferred Frequency Layer for 64QAM NRT) . . . . . 903
PrefLayer64QAMNRT (Preferred Layer for 64QAM NRT) . . . . . . . . . . 904
PFL64QAMStr (Preferred Frequency Layer for 64QAM Streaming) . . 905
PrefLayer64QAMStr (Preferred Layer for 64QAM Streaming) . . . . . . 906
PFLCSHSAMR (Preferred Frequency Layer for CS voice HSPA AMR) . .
907
PrefLayerCSHSAMR (Preferred Layer for CS voice HSPA AMR) . . . . 908
PFLCSHSAMRNRT (Preferred Frequency Layer for CS voice HSPA AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 909
PrefLayerCSHSAMRNRT (Preferred Layer for CS voice HSPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910
PFLCSHSNRT (Preferred Frequency Layer for CS voice HSPA NRT) 911
PrefLayerCSHSNRT (Preferred Layer for CS voice HSPA NRT) . . . . 912
PFLCSHSStr (Preferred Frequency Layer for CS voice HSPA Streaming)
913
PrefLayerCSHSStr (Preferred Layer for CS voice HSPA Streaming) . 913
PFLChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . . . . 914
PFLDBHSDAMR (Preferred Frequency Layer for DB-DC-HSDPA AMR) .
915
PrefLayerDBHSDAMR (Preferred Layer for DB-DC-HSDPA AMR) . . 916
PFLDBHSDAMRNRT (Preferred Frequency Layer for DB-DC-HSDPA
AMR and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917
PrefLayerDBHSDAMRNRT (Preferred Layer for DB-DC-HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 918
PFLDBHSDNRT (Preferred Frequency Layer for DB-DC-HSDPA NRT) .
919
PrefLayerDBHSDNRT (Preferred Layer for DB-DC-HSDPA NRT) . . . 920
PFLDBHSDStr (Preferred Frequency Layer for DB-DC-HSDPA
Streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 921
PrefLayerDBHSDStr (Preferred Layer for DB-DC-HSDPA Streaming) 922
PFLDCHSDAMR (Preferred Frequency Layer for DC-HSDPA AMR) . 923
PrefLayerDCHSDAMR (Preferred Layer for DC-HSDPA AMR) . . . . . 924
PFLDCHSDAMRNRT (Preferred Frequency Layer for DC-HSDPA AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 925
PrefLayerDCHSDAMRNRT (Preferred Layer for DC-HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 925
PFLDCHSDNRT (Preferred Frequency Layer for DC-HSDPA NRT) . 927
PrefLayerDCHSDNRT (Preferred Layer for DC-HSDPA NRT) . . . . . . 927
PFLDCHSDStr (Preferred Frequency Layer for DC-HSDPA Streaming) .
928
PrefLayerDCHSDStr (Preferred Layer for DC-HSDPA Streaming) . . . 929
PFLDCMIAMR (Preferred Frequency Layer for DC and MIMO AMR) . 930
PrefLayerDCMIAMR (Preferred Layer for DC and MIMO AMR) . . . . . 931
PFLDCMIAMRNRT (Preferred Frequency Layer for DC and MIMO AMR
and NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 932
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 502
Table 503
Table 504
Table 505
Table 506
Table 507
Table 508
Table 509
Table 510
Table 511
Table 512
Table 513
Table 514
Table 515
Table 516
Table 517
Table 518
Table 519
Table 520
Table 521
Table 522
Table 523
Table 524
Table 525
Table 526
Table 527
Table 528
Table 529
Table 530
Table 531
Table 532
Table 533
Table 534
Table 535
Table 536
Table 537
Table 538
Table 539
Table 540
DN70456011
PrefLayerDCMIAMRNRT (Preferred Layer for DC and MIMO AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933
PFLDCMINRT (Preferred Frequency Layer for DC and MIMO NRT) . 934
PrefLayerDCMINRT (Preferred Layer for DC and MIMO NRT) . . . . . 935
PFLDCMIStr (Preferred Frequency Layer for DC and MIMO Streaming) .
936
PrefLayerDCMIStr (Preferred Layer for DC and MIMO Streaming) . . 936
PFLFDPCHAMR (Preferred Frequency Layer for FDPCH AMR) . . . . 937
PrefLayerFDPCHAMR (Preferred Layer for F-DPCH AMR) . . . . . . . . 938
PFLFDPCHAMRNRT (Preferred Frequency Layer for FDPCH AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 939
PrefLayerFDPCHAMRNRT (Preferred Layer for F-DPCH AMR and NRT)
940
PFLFDPCHNRT (Preferred Frequency Layer for FDPCH NRT) . . . . 941
PrefLayerFDPCHNRT (Preferred Layer for F-DPCH NRT) . . . . . . . . 942
PFLFDPCHStr (Preferred Frequency Layer for FDPCH Streaming) . 943
PrefLayerFDPCHStr (Preferred Layer for F-DPCH Streaming) . . . . . 943
PFLFastMovUECS (Preferred Frequency Layer for fast moving UE CS) .
944
PrefLayerFastMovUECS (Preferred Layer for fast moving UE CS) . . 945
PFLFastMovUEPS (Preferred Frequency Layer for fast moving UE PS) .
946
PrefLayerFastMovUEPS (Preferred Layer for fast moving UE PS) . . 947
PFLHSDPAAMR (Preferred Frequency Layer for HSDPA AMR) . . . . 948
PrefLayerHSDPAAMR (Preferred Layer for HSDPA AMR) . . . . . . . . 949
PFLHSDPAAMRNRT (Preferred Frequency Layer for HSDPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
PrefLayerHSDPAAMRNRT (Preferred Layer for HSDPA AMR and NRT)
951
PFLHSDPANRT (Preferred Frequency Layer for HSDPA NRT) . . . . 952
PrefLayerHSDPANRT (Preferred Layer for HSDPA NRT) . . . . . . . . . 953
PFLHSDPAStr (Preferred Frequency Layer for HSDPA Streaming) . 954
PrefLayerHSDPAStr (Preferred Layer for HSDPA Streaming) . . . . . . 954
PFLHSPAAMR (Preferred Frequency Layer for HSPA AMR) . . . . . . 955
PrefLayerHSPAAMR (Preferred Layer for HSPA AMR) . . . . . . . . . . . 956
PFLHSPAAMRNRT (Preferred Frequency Layer for HSPA AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 957
PrefLayerHSPAAMRNRT (Preferred Layer for HSPA AMR and NRT) 958
PFLHSPANRT (Preferred Frequency Layer for HSPA NRT) . . . . . . . 959
PrefLayerHSPANRT (Preferred Layer for HSPA NRT) . . . . . . . . . . . 960
PFLHSPAStr (Preferred Frequency Layer for HSPA Streaming) . . . . 961
PrefLayerHSPAStr (Preferred Layer for HSPA Streaming) . . . . . . . . 961
PFLIdentifier (PFL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 962
PFLMIMOAMR (Preferred Frequency Layer for MIMO AMR) . . . . . . 963
PrefLayerMIMOAMR (Preferred Layer for MIMO AMR) . . . . . . . . . . . 964
PFLMIMOAMRNRT (Preferred Frequency Layer for MIMO AMR and
NRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965
PrefLayerMIMOAMRNRT (Preferred Layer for MIMO AMR and NRT) 966
PFLMIMONRT (Preferred Frequency Layer for MIMO NRT) . . . . . . . 967
Id:0900d80580931b1d
Confidential
83
Radio Network Parameters in Flexi Direct
Table 541
Table 542
Table 543
Table 544
Table 545
Table 546
Table 547
Table 548
Table 549
Table 550
Table 551
Table 552
Table 553
Table 554
Table 555
Table 556
Table 557
Table 558
Table 559
Table 560
Table 561
Table 562
Table 563
Table 564
Table 565
Table 566
Table 567
Table 568
Table 569
Table 570
Table 571
Table 572
Table 573
Table 574
Table 575
Table 576
Table 577
84
PrefLayerMIMONRT (Preferred Layer for MIMO NRT) . . . . . . . . . . . . 968
PFLMIMOStr (Preferred Frequency Layer for MIMO Streaming) . . . . 969
PrefLayerMIMOStr (Preferred Layer for MIMO Streaming) . . . . . . . . . 969
PFLR99AMR (Preferred Frequency Layer for R99 AMR) . . . . . . . . . . 970
PrefLayerR99AMR (Preferred Layer for R99 AMR) . . . . . . . . . . . . . . . 971
PFLR99AMRNRT (Preferred Frequency Layer for R99 AMR and NRT) . .
972
PrefLayerR99AMRNRT (Preferred Layer for R99 AMR and NRT) . . . 973
PFLR99NRT (Preferred Frequency Layer for R99 NRT) . . . . . . . . . . . 974
PrefLayerR99NRT (Preferred Layer for R99 NRT) . . . . . . . . . . . . . . . 975
PFLR99Str (Preferred Frequency Layer for R99 Streaming) . . . . . . . . 976
PrefLayerR99Str (Preferred Layer for R99 Streaming) . . . . . . . . . . . . 977
AMRLoadTxPower (Indicator for downlink radio power load) . . . . . . . 978
AMRNumofReconf (AMRNumofReconf) . . . . . . . . . . . . . . . . . . . . . . . 978
AMRwinSizeSCload (AMRwinSizeSCload) . . . . . . . . . . . . . . . . . . . . . 979
AdjustmentPeriod (Adjustment period time) . . . . . . . . . . . . . . . . . . . . 980
AdjustmentRatio (Adjustment ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . 981
AutoACDecRestHysNRTQ (Automatic Access Class Decrease Restriction
Level Hysteresis for NRT queue length trigger) . . . . . . . . . . . . . . . . . . 983
AutoACDecRestHysRTWP (Automatic Access Class Decrease Restriction
Level Hysteresis for Received Total Wideband Power trigg) . . . . . . . . 984
AutoACIncRestHysNRTQ (Automatic Access Class Increase Restriction
Level Hysteresis for NRT queue length trigger) . . . . . . . . . . . . . . . . . . 985
AutoACIncRestHysRTWP (Automatic Access Class Increase Restriction
Level Hysteresis for Received Total Wideband Powertrigge) . . . . . . . 986
AutoACMaxRestLevel (Automatic Access Class Maximum Restriction
Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 987
AutoACRLevelUpdInt (Automatic Access Class Restriction Level Update
Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 988
AutoACRTrigRNCLoad (Automatic Access Class Restriction Trigger of
RNC Load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 989
AutoACRestForCellPCH (Access Restriction for Cell_PCH state UE) 991
BitRateSetPSNRT (Bit rate set for PS NRT DCHs) . . . . . . . . . . . . . . . 992
DCHSlopeOfTheCurve (DCH slope of the curve) . . . . . . . . . . . . . . . . 993
DLInLoopPCStepSizeCPC (DL inner loop PC step size for CPC users) . .
994
DLLoadSource (DL Load Source) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995
DLmaxBitRatePerSF (Maximum DL bit rate per spreading factor) . . . 996
DLmaxBitRateSF128 (Maximum DL bit rate with spreading factor 128) . .
997
DLmaxBitRateSF16 (Maximum DL bit rate with spreading factor 16) . 998
DLmaxBitRateSF256 (Maximum DL bit rate with spreading factor 256) . .
999
DLmaxBitRateSF32 (Maximum DL bit rate with spreading factor 32) 1000
DLmaxBitRateSF64 (Maximum DL bit rate with spreading factor 64) 1001
DLpuncturingLimit (Downlink puncturing limit) . . . . . . . . . . . . . . . . . . 1002
DownlinkInnerLoopPCStepSize (Power-adjusting step size in WCDMA
BTS for DL closed loop PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1004
DynHSUPABLERAlgTrgTime (Time to trigger Dyn HSUPA BLER
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 578
Table 579
Table 580
Table 581
Table 582
Table 583
Table 584
Table 585
Table 586
Table 587
Table 588
Table 589
Table 590
Table 591
Table 592
Table 593
Table 594
Table 595
Table 596
Table 597
Table 598
Table 599
Table 600
Table 601
Table 602
Table 603
Table 604
DN70456011
Algorithm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005
DynHSUPABLERBurstDataRx (Retransmissions in Dyn HSUPA BLER for
Bursty Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006
DynHSUPABLERContDataRx10 (Retransmissions in Dyn HSUPA BLER
for Cont Data 10msTTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
DynHSUPABLERContDataRx2 (Retransmissions in Dyn HSUPA BLER for
Cont Data 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009
DynHSUPABLERFrameWinSiz (Window size for FP Frames
Measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010
DynHSUPABLERMaxRateThrB (Peak rate threshold for bursty data of Dyn
HSUPA BLER) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1011
DynHSUPABLERMaxRateThrC10 (Peak rate thr for cont data of Dyn HSUPA BLER 10 ms TTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1012
DynHSUPABLERMaxRateThrC2 (Peak rate thr for cont data of Dyn HSUPA BLER 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1013
DynHSUPABLERPeakRateRx (Retransmissions in Dyn HSUPA BLER for
Peak data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1014
DynHSUPABLERThrBurstyTP (Bursty Data throughput threshold per TTI)
1016
DynHSUPABurstyPeriod (Bursty Period for Dyn HSUPA BLER) . . . 1017
EDCHSlopeOfTheCurve (EDCH slope of the curve) . . . . . . . . . . . . 1018
ExpectReorderingPDCP (Expect Reordering for PDCP) . . . . . . . . . 1019
FOLPCSIRTgtModInt (Faster OLPC SIR target modification interval) . . .
1020
FOLPCStepSizSIRTgt (Faster OLPC step size of SIR target changes) . .
1021
FmaxPeriodPDCP (F Max Period for PDCP) . . . . . . . . . . . . . . . . . . 1022
FmaxTimePDCP (F Max Time for PDCP) . . . . . . . . . . . . . . . . . . . . 1023
FreePtxSafetyMarginStr (Safety margin for free transmitted power for
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1024
GainFactorControlPartPRACHmessage (Gain factor for control part of
PRACH message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1025
PrachBetaC120 (Gain factor for control part of PRACH message with 120
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1026
PrachBetaC15 (Gain factor for control part of PRACH message with 15
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027
PrachBetaC30 (Gain factor for control part of PRACH message with 30
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1028
PrachBetaC60 (Gain factor for control part of PRACH message with 60
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1029
GainFactorDataPartPRACHmessage (Gain factor for data part of PRACH
message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1030
PrachBetaD120 (Gain factor for data part of PRACH message with 120
ksps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1031
PrachBetaD15 (Gain factor for data part of PRACH message with 15 ksps)
1032
PrachBetaD30 (Gain factor for data part of PRACH message with 30 ksps)
1033
PrachBetaD60 (Gain factor for data part of PRACH message with 60 ksps)
1034
Id:0900d80580931b1d
Confidential
85
Radio Network Parameters in Flexi Direct
Table 605
Table 606
Table 607
Table 608
Table 609
Table 610
Table 611
Table 612
Table 613
Table 614
Table 615
Table 616
Table 617
Table 618
Table 619
Table 620
Table 621
Table 622
Table 623
Table 624
Table 625
Table 626
Table 627
Table 628
Table 629
Table 630
Table 631
Table 632
Table 633
Table 634
Table 635
Table 636
Table 637
86
HSFACHDiscardTimer (Discard Timer for BCCH, CCCH and DCCH data
on HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035
HSFACHResetTimer (MAC-ehs Reset Timer for xCCH data on HS-FACH)
1037
HeaderCompressionMethod (Header compression algorithm of PDCP) . .
1038
L1BurstDataBLERTrgtEDCH (Layer1 Bursty Data BLER target for EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1039
L1ContBLERTrgtEDCH10 (Layer1 Continuous BLER target for E-DCH TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1040
L1ContBLERTrgtEDCH2 (Layer1 Continuous BLER target for E-DCH TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1041
L1PeakRateBLERTrgtEDCH (Layer1 Peak Data Rate BLER target for EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1042
LoadBasedAMRCodecMode (Usage of Load based AMR codec mode
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1044
MaxAdjustmentStep (Maximum adjustment step) . . . . . . . . . . . . . . . 1044
MaxFreezingTime (Maximum freezing time) . . . . . . . . . . . . . . . . . . . 1046
MaxHeaderPDCP (Max Header for PDCP) . . . . . . . . . . . . . . . . . . . . 1047
MaxNumberOfReAttemptsCong (Maximum number of re-attempts to hunt
resources) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1048
MinPrefChange (Trigger for sending the updated reference power to
BTSs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1049
NonTCPspacePDCP (Non-TCP Space for PDCP) . . . . . . . . . . . . . . 1050
PCPreamble (Uplink DPCCH power control preamble) . . . . . . . . . . . 1051
PCrangeDL (Radio link downlink power control range) . . . . . . . . . . . 1052
PTTUEMappingARPCap (PTT UE mapping for ARP pre-emption
capability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1053
PTTUEMappingARPPrioLevel (PTT UE mapping for ARP priority level) .
1055
PTTUEMappingARPQue (PTT UE Mapping for ARP queuing allowed) . .
1056
PTTUEMappingARPVul (PTT UE mapping for ARP pre-emption
vulnerability) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1058
PTTUEMappingSignInd (PTT UE mapping for Signaling indication) . 1059
PTTUEMappingTC (PTT UE mapping for Traffic Class) . . . . . . . . . . 1061
PTTUEMappingTHP (PTT UE mapping for Traffic handling priority) . 1062
PagingRestrictionInd (Paging Restriction Indication for PPAC) . . . . . 1064
PeriodULRCAMR (Period for CS AMR RRC TFC control requests) . 1065
PrefSubtract (Reference power subtraction parameter) . . . . . . . . . . 1066
RAU_LAU_RestrictionInd (RAU and LAU Restriction Indication for PPAC)
1067
RNACChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1068
RNACId (RNAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069
RNARDSACCell_DCH (Access class restriction level for Cell_DCH) 1070
RNARDSACCell_PCH (Access class restriction level for Cell_PCH) 1071
RNARDSACGuardTime (Access class restriction guard time) . . . . . 1073
RRCConnSetupMsgSize (RRC Connection Setup Message Size
Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 638
Table 639
Table 640
Table 641
Table 642
Table 643
Table 644
Table 645
Table 646
Table 647
Table 648
Table 649
Table 650
Table 651
Table 652
Table 653
Table 654
Table 655
Table 656
Table 657
Table 658
Table 659
Table 660
Table 661
Table 662
Table 663
Table 664
Table 665
Table 666
Table 667
Table 668
Table 669
Table 670
Table 671
Table 672
Table 673
Table 674
DN70456011
SRBDelay (SRB delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1076
SignallingLinkInactivityTimer (Signalling link inactivity timer) . . . . . . 1077
StepSizeForDCHBLER (Step Size for DCH BLER calculation) . . . . 1078
StepSizeForEDCHBLER (Step Size for EDCH BLER calculation) . . 1079
TCPspacePDCP (TCP Space for PDCP) . . . . . . . . . . . . . . . . . . . . . 1080
TDMultForHSDPAStreaming (Transfer Delay multiplier for HSDPA
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1081
TFDCHZeroBitRate (Zero size transport block to L1 CRC calculation) . .
1082
ULFastOLPCDTXthld (DTX threshold for uplink faster outer loop) . . 1083
ULmaxBitRatePerSF (Maximum UL bit rate per spreading factor) . . 1085
ULmaxBitRateSF128 (Maximum UL bit rate with spreading factor 128) .
1086
ULmaxBitRateSF16 (Maximum UL bit rate with spreading factor 16) 1087
ULmaxBitRateSF256 (Maximum UL bit rate with spreading factor 256) .
1088
ULmaxBitRateSF32 (Maximum UL bit rate with spreading factor 32) 1089
ULmaxBitRateSF64 (Maximum UL bit rate with spreading factor 64) 1090
ULmaxBitRateSF8 (Maximum UL bit rate with spreading factor 8) . 1091
ULpuncturingLimit (Uplink puncturing limit) . . . . . . . . . . . . . . . . . . . 1092
UlScrCodeMin (Uplink scrambling code minimum value) . . . . . . . . . 1093
UpLinkInitialTransmitPowerMode (Initial transmit power in uplink compressed mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1095
UpLinkRecoveryPeriodPowerMode (Recovery Period Power in UL Compressed Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1096
AMRWithEDCH (Usage of AMR service with E-DCH) . . . . . . . . . . . 1098
AMRWithHSDSCH (Usage of AMR service with HS-DSCH) . . . . . . 1099
AutoACResEnabled (Automatic Access Class Restriction Enabled) 1101
AutomDLPlanUpdEnabled (Automatic DL Plan update enabled) . . . 1103
CCCHforCUCallowed (Usage of CCCH for Cell/URA Update Confirm
allowed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104
CMmasterSwitch (Compressed mode master switch) . . . . . . . . . . . 1105
CSFBEnabled (CSFB Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1106
CSVoiceServiceSupport (CS Voice Service Support in FD-RNC) . . 1107
CUCforPCHtoDCHallowed (Direct State Transition From Cell_PCH to
Cell_DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1108
CVUserInactInSignConnRel (Cause value usage in NAS signaling connection release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1109
DCH00SuppOnIurEnabled (DCH 0/0 Support On Iur Enabled) . . . . 1110
DCHBitRateBalancing (DCH bit rate balancing on/off switch) . . . . . 1111
DCHScheOverIur (DCH Scheduling Over Iur) . . . . . . . . . . . . . . . . . 1112
DCHtoPCHEnabled (Enabling direct Cell_DCH to PCH state transition) .
1113
DLOptimisationUsage (Dynamic link optimisation usage) . . . . . . . . 1114
DLPSGTPDataThroughputMax (Maximum allowed DL PS GTP data
throughput) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1115
DynUsageHSDPAReturnChannel (Dynamic usage of UL NRT DCH HSDPA return Channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1116
EUTRAdetection (E-UTRA detection) . . . . . . . . . . . . . . . . . . . . . . . . 1117
Id:0900d80580931b1d
Confidential
87
Radio Network Parameters in Flexi Direct
Table 675
Table 676
Table 677
Table 678
Table 679
Table 680
Table 681
Table 682
Table 683
Table 684
Table 685
Table 686
Table 687
Table 688
Table 689
Table 690
Table 691
Table 692
Table 693
Table 694
Table 695
Table 696
Table 697
Table 698
Table 699
Table 700
Table 701
Table 702
Table 703
Table 704
Table 705
Table 706
Table 707
Table 708
Table 709
Table 710
Table 711
88
EmergencyCallISHOSupport (Emergency Call lSHO Support) . . . . . 1118
EmergencyCallRedirect (Emergency Call Redirect) . . . . . . . . . . . . . 1119
FRLCEnabled (Flexible RLC Enabled) . . . . . . . . . . . . . . . . . . . . . . . 1120
FastDormancyEnabled (Fast Dormancy activation / de-activation
parameter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1121
FastPCHSwitchEnabled (Enabling Fast Cell_PCH Switching feature) . . .
1122
FasterOLPCEnabled (Faster OLPC Enabled) . . . . . . . . . . . . . . . . . . 1123
FemtoHandoverControl (Femto Handover Control) . . . . . . . . . . . . . . 1125
FlexULRLCEnabled (Flexible UL RLC Enabled) . . . . . . . . . . . . . . . . 1126
FlexUpgrUsage (Usage of the Flexible Upgrade of the NRT DCH data
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127
HLSModeSelection (Higher Layer Scheduling mode selection) . . . . 1128
HSDPA16KBPSReturnChannel (HSDPA 16 kbps UL DCH return channel
on/off switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1129
HSDPA48UsersEnabled (HSDPA 48 users enabled) . . . . . . . . . . . . 1131
HSDPADynamicResourceAllocation (HSDPA Dynamic Resource
Allocation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1132
HSDPAMobility (Serving HS-DSCH cell change and SHO on/off switch) .
1133
HSPAInterRNCMobility (HSPA Inter-RNC Mobility) . . . . . . . . . . . . . 1134
HSPAOverIurExt (HSPA Over Iur Extension) . . . . . . . . . . . . . . . . . . 1136
HSUPADynBLEREnabled (HSUPA Dynamic BLER Enabled) . . . . . 1137
IFHOOverIurExt (IFHO Over Iur Extension) . . . . . . . . . . . . . . . . . . . 1138
ISHOCancellation (Inter-System Handover Cancellation) . . . . . . . . . 1139
ISHOInIurMobility (ISHO In Iur Mobility) . . . . . . . . . . . . . . . . . . . . . . 1140
IntelligentEmergencyCallISHOSupport (Intelligent Emergency Call ISHO
Support) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1141
IuPSrelWait3G2GMultiServ (Time supervision for releasing Iu-PS
connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1142
LFDProfEnabled (LFD profiling Enabled) . . . . . . . . . . . . . . . . . . . . . 1143
MIBPLMNIdIncluded (MIB PLMN Identity Included) . . . . . . . . . . . . . 1144
MOCNenabled (Multi-Operator Core Network enabled) . . . . . . . . . . 1145
PBSpolicy (Priority based scheduling policy) . . . . . . . . . . . . . . . . . . . 1146
PPACEnabled (Paging Permission With Access Control Enabled) . . 1148
PSOpThroUsage (Throughput based optimisation of the PS algorithm
usage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150
PTTEnabled (Push to talk enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 1153
PWSMDriftAllowed (Cell shutdown allowed with drifting UE) . . . . . . 1155
PostVerifPeriodDLSynch (Post-verification period in downlink
synchronization) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1156
PowerBalancing (Power Balancing on/off) . . . . . . . . . . . . . . . . . . . . . 1157
RABDRAEnabled (Usage of the direct resource allocation for PS NRT
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1159
RNFCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 1160
RNFCId (RNFC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1161
RRCSetupCCHEnabledR99 (RRC setup on CCH enabled for R99 UE) . .
1162
SIBCapabilityCheck (SIB Capability Check) . . . . . . . . . . . . . . . . . . . 1164
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 712
Table 713
Table 714
Table 715
Table 716
Table 717
Table 718
Table 719
Table 720
Table 721
Table 722
Table 723
Table 724
Table 725
Table 726
Table 727
Table 728
Table 729
Table 730
Table 731
Table 732
Table 733
Table 734
Table 735
Table 736
Table 737
Table 738
Table 739
Table 740
Table 741
Table 742
Table 743
Table 744
Table 745
Table 746
Table 747
Table 748
Table 749
Table 750
Table 751
Table 752
Table 753
Table 754
DN70456011
SLHOCmAllowedNRT (CM allowed for NRT connection in SLHO) . 1164
SRVCCEnabled (SRVCC Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . 1165
SignConnActivitySupervision (Activity supervision for NAS signaling
connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1166
WPSCallRestriction (Restricting overloaded WPS calls) . . . . . . . . . 1168
WireLessPriorityService (Usage of the Wireless Priority Service) . . 1170
AARConfigTable (Application Aware RAN Configuration Table) . . . 1172
AppGrpId (Application Group Identifier) . . . . . . . . . . . . . . . . . . . . . . 1173
DSCPCode1 (DSCP Code1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1174
DSCPCode2 (DSCP Code2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1176
DSCPCode3 (DSCP Code3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1177
DSCPCode4 (DSCP Code4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1178
DSCPCode5 (DSCP Code5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1179
Precedence (Precedence) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1181
TargetSPIforSPI0 (Target SPI for SPI 0) . . . . . . . . . . . . . . . . . . . . . 1182
TargetSPIforSPI1 (Target SPI for SPI 1) . . . . . . . . . . . . . . . . . . . . . 1183
TargetSPIforSPI10 (Target SPI for SPI 10) . . . . . . . . . . . . . . . . . . . 1185
TargetSPIforSPI11 (Target SPI for SPI 11) . . . . . . . . . . . . . . . . . . . 1186
TargetSPIforSPI2 (Target SPI for SPI 2 ) . . . . . . . . . . . . . . . . . . . . . 1188
TargetSPIforSPI3 (Target SPI for SPI 3 ) . . . . . . . . . . . . . . . . . . . . . 1189
TargetSPIforSPI4 (Target SPI for SPI 4) . . . . . . . . . . . . . . . . . . . . . 1191
TargetSPIforSPI5 (Target SPI for SPI 5) . . . . . . . . . . . . . . . . . . . . . 1192
TargetSPIforSPI6 (Target SPI for SPI 6) . . . . . . . . . . . . . . . . . . . . . 1194
TargetSPIforSPI7 (Target SPI for SPI 7) . . . . . . . . . . . . . . . . . . . . . 1195
TargetSPIforSPI8 (Target SPI for SPI 8) . . . . . . . . . . . . . . . . . . . . . 1197
TargetSPIforSPI9 (Target SPI for SPI 9) . . . . . . . . . . . . . . . . . . . . . 1198
ARPWeight (ARP based weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200
WeightForARP1 (Weight for ARP1) . . . . . . . . . . . . . . . . . . . . . . . . . 1201
WeightForARP2 (Weight for ARP2) . . . . . . . . . . . . . . . . . . . . . . . . . 1202
WeightForARP3 (Weight for ARP3) . . . . . . . . . . . . . . . . . . . . . . . . . 1203
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA) . . 1204
CPCNRT10msTTI (CPC NRT 10 ms TTI) . . . . . . . . . . . . . . . . . . . . 1205
N10msCPCOptObjective (CPC Optimization objective NRT 10ms TTI) .
1206
N10msCQIDTXTimer (CQI DTX Timer NRT 10ms TTI) . . . . . . . . . . 1207
N10msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 10ms TTI)
1209
N10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle NRT
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210
N10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 NRT
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1211
N10msMACDTXCycle (MAC DTX Cycle NRT 10ms TTI) . . . . . . . . 1213
N10msMACInacThr (MAC Inactivity Threshold NRT 10ms TTI) . . . 1214
N10msUEDPCCHburst1 (UE DPCCH burst1 NRT 10ms TTI) . . . . . 1215
N10msUEDPCCHburst2 (UE DPCCH burst2 NRT 10ms TTI) . . . . . 1216
N10msUEDRXCycle (UE DRX Cycle NRT 10ms TTI) . . . . . . . . . . . 1217
N10msUEDTXCycle1 (UE DTX Cycle 1 NRT 10ms TTI) . . . . . . . . . 1218
N10msUEDTXCycle2 (UE DTX Cycle 2 NRT 10ms TTI) . . . . . . . . . 1219
Id:0900d80580931b1d
Confidential
89
Radio Network Parameters in Flexi Direct
Table 755
Table 756
Table 757
Table 758
Table 759
Table 760
Table 761
Table 762
Table 763
Table 764
Table 765
Table 766
Table 767
Table 768
Table 769
Table 770
Table 771
Table 772
Table 773
Table 774
Table 775
Table 776
Table 777
Table 778
Table 779
Table 780
Table 781
Table 782
Table 783
Table 784
Table 785
Table 786
Table 787
Table 788
Table 789
Table 790
Table 791
90
N10msUEDTXLongPreamble (UE DTX Long Preamble N10ms) . . . 1220
CPCNRT2msTTI (CPC NRT 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . . . 1221
N2msCPCOptObjective (CPC Optimization objective NRT 2ms TTI) 1222
N2msCQIDTXTimer (CQI DTX Timer NRT 2ms TTI) . . . . . . . . . . . . 1223
N2msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 2ms TTI) . .
1225
N2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle NRT
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1226
N2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 NRT
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227
N2msMACDTXCycle (MAC DTX Cycle NRT 2ms TTI) . . . . . . . . . . . 1229
N2msMACInacThr (MAC Inactivity Threshold NRT 2ms TTI) . . . . . . 1230
N2msUEDPCCHburst1 (UE DPCCH burst1 NRT 2ms TTI) . . . . . . . 1231
N2msUEDPCCHburst2 (UE DPCCH burst2 NRT 2ms TTI) . . . . . . . 1232
N2msUEDRXCycle (UE DRX Cycle NRT 2ms TTI) . . . . . . . . . . . . . 1233
N2msUEDTXCycle1 (UE DTX Cycle 1 NRT 2ms TTI) . . . . . . . . . . . 1234
N2msUEDTXCycle2 (UE DTX Cycle 2 NRT 2ms TTI) . . . . . . . . . . . 1235
N2msUEDTXLongPreamble (UE DTX Long Preamble NRT 2ms TTI) . . .
1237
CPCStreaming10msTTI (CPC Streaming 10 ms TTI) . . . . . . . . . . . . 1238
S10msCPCOptObjective (CPC Optimization objective Str 10ms TTI) . . .
1239
S10msCQIDTXTimer (CQI DTX Timer Str 10ms TTI) . . . . . . . . . . . . 1240
S10msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 10ms TTI) .
1241
S10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Str
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1242
S10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Str
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1244
S10msMACDTXCycle (MAC DTX Cycle Str 10ms TTI) . . . . . . . . . . 1245
S10msMACInacThr (MAC Inactivity Threshold Str 10ms TTI) . . . . . 1246
S10msUEDPCCHburst1 (UE DPCCH burst1 Str 10ms TTI) . . . . . . . 1247
S10msUEDPCCHburst2 (UE DPCCH burst2 Str 10ms TTI) . . . . . . . 1248
S10msUEDRXCycle (UE DRX Cycle Str 10ms TTI) . . . . . . . . . . . . . 1249
S10msUEDTXCycle1 (UE DTX Cycle 1 Str 10ms TTI) . . . . . . . . . . . 1250
S10msUEDTXCycle2 (UE DTX Cycle 2 Str 10ms TTI) . . . . . . . . . . . 1251
S10msUEDTXLongPreamble (UE DTX Long Preamble Str 10ms TTI) . .
1252
CPCStreaming2msTTI (CPC Streaming 2 ms TTI) . . . . . . . . . . . . . . 1253
S2msCPCOptObjective (CPC Optimization objective Str 2ms TTI) . 1254
S2msCQIDTXTimer (CQI DTX Timer Str 2ms TTI) . . . . . . . . . . . . . . 1255
S2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 2ms TTI) . . .
1257
S2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Str
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1258
S2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Str
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259
S2msMACDTXCycle (MAC DTX Cycle Str 2ms TTI) . . . . . . . . . . . . 1260
S2msMACInacThr (MAC Inactivity Threshold Str 2ms TTI) . . . . . . . 1262
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 792
Table 793
Table 794
Table 795
Table 796
Table 797
Table 798
Table 799
Table 800
Table 801
Table 802
Table 803
Table 804
Table 805
Table 806
Table 807
Table 808
Table 809
Table 810
Table 811
Table 812
Table 813
Table 814
Table 815
Table 816
Table 817
Table 818
Table 819
Table 820
Table 821
Table 822
Table 823
Table 824
Table 825
Table 826
Table 827
Table 828
Table 829
DN70456011
S2msUEDPCCHburst1 (UE DPCCH burst1 Str 2ms TTI) . . . . . . . . 1263
S2msUEDPCCHburst2 (UE DPCCH burst2 Str 2ms TTI) . . . . . . . . 1264
S2msUEDRXCycle (UE DRX Cycle Str 2ms TTI) . . . . . . . . . . . . . . 1265
S2msUEDTXCycle1 (UE DTX Cycle 1 Str 2ms TTI) . . . . . . . . . . . . 1266
S2msUEDTXCycle2 (UE DTX Cycle 2 Str 2ms TTI) . . . . . . . . . . . . 1267
S2msUEDTXLongPreamble (UE DTX Long Preamble Str 2ms TTI) 1268
CPCVoice10msTTI (CPC Voice 10 ms TTI) . . . . . . . . . . . . . . . . . . . 1269
V10msCPCOptObjective (CPC Optimization objective Voi 10ms TTI) . . .
1271
V10msCQIDTXTimer (CQI DTX Timer Voi 10ms TTI) . . . . . . . . . . . 1272
V10msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 10ms TTI)
1273
V10msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Voi
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1274
V10msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Voi
10ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1276
V10msMACDTXCycle (MAC DTX Cycle Voi 10ms TTI) . . . . . . . . . . 1277
V10msMACInacThr (MAC Inactivity Threshold Voi 10ms TTI) . . . . . 1278
V10msUEDPCCHburst1 (UE DPCCH burst1 Voi 10ms TTI) . . . . . . 1279
V10msUEDPCCHburst2 (UE DPCCH burst2 Voi 10ms TTI) . . . . . . 1280
V10msUEDRXCycle (UE DRX Cycle Voi 10ms TTI) . . . . . . . . . . . . 1281
V10msUEDTXCycle1 (UE DTX Cycle 1 Voi 10ms TTI) . . . . . . . . . . 1282
V10msUEDTXCycle2 (UE DTX Cycle 2 Voi 10ms TTI) . . . . . . . . . . 1283
V10msUEDTXLongPreamble (UE DTX Long Preamble Voi 10ms TTI) . .
1284
CPCVoice2msTTI (CPC Voice 2 ms TTI) . . . . . . . . . . . . . . . . . . . . . 1285
V2msCPCOptObjective (CPC Optimization objective Voi 2ms TTI) . 1287
V2msCQIDTXTimer (CQI DTX Timer Voi 2ms TTI) . . . . . . . . . . . . . 1288
V2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 2ms TTI) . .
1289
V2msInacThrUEDRXCycle (Inactivity Threshold for UE DRX Cycle Voi
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1290
V2msInacThrUEDTXCycl2 (Inactivity Threshold for UE DTX Cycle 2 Voi
2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1292
V2msMACDTXCycle (MAC DTX Cycle Voi 2ms TTI) . . . . . . . . . . . . 1293
V2msMACInacThr (MAC Inactivity Threshold Voi 2ms TTI) . . . . . . . 1294
V2msUEDPCCHburst1 (UE DPCCH burst1 Voi 2ms TTI) . . . . . . . . 1295
V2msUEDPCCHburst2 (UE DPCCH burst2 Voi 2ms TTI) . . . . . . . . 1296
V2msUEDRXCycle (UE DRX Cycle Voi 2ms TTI) . . . . . . . . . . . . . . 1297
V2msUEDTXCycle1 (UE DTX Cycle 1 Voi 2ms TTI) . . . . . . . . . . . . 1298
V2msUEDTXCycle2 (UE DTX Cycle 2 Voi 2ms TTI) . . . . . . . . . . . . 1300
V2msUEDTXLongPreamble (UE DTX Long Preamble Voi 2ms TTI) 1301
CPICHECNOSRBHSPA (CPICH EcNo for SRB on HSPA) . . . . . . . 1302
CPICHECNOThreEDCH2MS (CPICH ECNO Threshold for E-DCH TTI 2
ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1303
CPICHRSCPThreEDCH2MS (CPICH RSCP Threshold for E-DCH TTI 2
ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1304
CPICHRSCPThreSRBHSDPA (CPICH RSCP Threshold for SRBs on
HSDPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1305
Id:0900d80580931b1d
Confidential
91
Radio Network Parameters in Flexi Direct
Table 830
Table 831
Table 832
Table 833
Table 834
Table 835
Table 836
Table 837
Table 838
Table 839
Table 840
Table 841
Table 842
Table 843
Table 844
Table 845
Table 846
Table 847
Table 848
Table 849
Table 850
Table 851
Table 852
Table 853
Table 854
Table 855
Table 856
Table 857
Table 858
92
DCellVsMIMOPreference (Dual Cell versus MIMO preference) . . . . 1306
DiscardTimerHSCSVoice (HSDPA Discard Timer for the CS voice
service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1307
DiscardTimerPTT (HSDPA Discard Timer for the PTT) . . . . . . . . . . . 1308
EDCHCTSwitchGuardTimer (E-DCH channel type switch guard timer) . .
1310
EDCHMACdflowtputStrTtT (Low throughput time to trigger for streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1311
EDCHMaxHARQReTxStr (E-DCH max number of HARQ retransmissions
for streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1312
EDCHMaxHarqReTxSRB (E-DCH maximum # of HARQ retransmissions
for 10 ms SRB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1313
EDCHMaxHarqReTxSRB2MS (E-DCH maximum # of HARQ retransmissions for 2 ms SRB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1314
EDCHMaxNumberOfHARQReTx (E-DCH maximum number of HARQ
retransmissions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1315
EDCHQOSClasses (E-DCH QoS classes) . . . . . . . . . . . . . . . . . . . . 1316
EnablDelayHHO (Enabling Delay HHO) . . . . . . . . . . . . . . . . . . . . . . 1317
EnablDelayStand (Enabling Delay Standard) . . . . . . . . . . . . . . . . . . 1318
FDPCHAllocMinInterval (Minimum interval between F-DPCH allocations)
1319
FDPCHAndSRBOnHSPATC (F-DPCH and SRBs on HSPA per TC) 1320
FDPCHSetupEC (DCH instead of F-DPCH based on Establishment
Cause) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1321
FactorEDCHMaxBRPSstream (Factor E-DCH max. Bit Rate for PS
streaming RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1324
FactorEDCHMaxBitRate (Factor to calculate EDCH maximum bit rate) . .
1325
FactorEDCHMaxBitRate2NRT (Factor E-DCH max. Bit Rate for 2 NRT
RAB combinations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1326
FactorEDCHMaxBitRate3NRT (Factor E-DCH max. Bit Rate for 3 NRT
RAB combinations) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1327
HSDPACPICHCTSRepPer (DCH to HS-DSCH switch CPICH Ec/No reporting period) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1328
HSDPACPICHEcNoThreshold (CPICH Ec/No threshold for serving HSDSCH cell change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1329
HSDPACellChangeRepetitionTime (Window for max repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1330
HSDPAChaTypeSwitchWindow (HSDPA channel type switching window)
1331
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1332
HSDPAPeakRateLimitRABMax (HSDPA peak rate limitation to the RAB
maximum) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1333
HSDPAPriority (HSDPA priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1335
HSDPARRCdiversity (SHO of the HSDPA capable UE) . . . . . . . . . . 1336
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1337
HSDSCHCTSwitchGuardTimer (HS-DSCH channel type switch guard
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1339
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 859
Table 860
Table 861
Table 862
Table 863
Table 864
Table 865
Table 866
Table 867
Table 868
Table 869
Table 870
Table 871
Table 872
Table 873
Table 874
Table 875
Table 876
Table 877
Table 878
Table 879
Table 880
Table 881
Table 882
Table 883
Table 884
Table 885
Table 886
Table 887
Table 888
Table 889
Table 890
Table 891
Table 892
Table 893
Table 894
Table 895
Table 896
Table 897
Table 898
DN70456011
HSDSCHGuardTimerLowThroughput (HS-DSCH guard timer due to low
throughput) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1340
HSDSCHQoSclasses (HS-DSCH QoS classes) . . . . . . . . . . . . . . . . 1341
HSPANBRValues (HSPA NBR values) . . . . . . . . . . . . . . . . . . . . . . 1342
NBRForPri0DL (Downlink NBR for Priority value 0) . . . . . . . . . . . . . 1344
NBRForPri0UL (Uplink NBR for Priority value 0) . . . . . . . . . . . . . . . 1345
NBRForPri10DL (Downlink NBR for Priority value 10) . . . . . . . . . . . 1346
NBRForPri10UL (Uplink NBR for Priority value 10) . . . . . . . . . . . . . 1347
NBRForPri11DL (Downlink NBR for Priority value 11) . . . . . . . . . . . 1348
NBRForPri11UL (Uplink NBR for Priority value 11) . . . . . . . . . . . . . 1349
NBRForPri12DL (Downlink NBR for Priority value 12) . . . . . . . . . . . 1350
NBRForPri12UL (Uplink NBR for Priority value 12) . . . . . . . . . . . . . 1351
NBRForPri1DL (Downlink NBR for Priority value 1) . . . . . . . . . . . . . 1352
NBRForPri1UL (Uplink NBR for Priority value 1) . . . . . . . . . . . . . . . 1353
NBRForPri2DL (Downlink NBR for Priority value 2) . . . . . . . . . . . . . 1354
NBRForPri2UL (Uplink NBR for Priority value 2) . . . . . . . . . . . . . . . 1355
NBRForPri3DL (Downlink NBR for Priority value 3) . . . . . . . . . . . . . 1356
NBRForPri3UL (Uplink NBR for Priority value 3) . . . . . . . . . . . . . . . 1357
NBRForPri4DL (Downlink NBR for Priority value 4) . . . . . . . . . . . . . 1358
NBRForPri4UL (Uplink NBR for Priority value 4) . . . . . . . . . . . . . . . 1359
NBRForPri5DL (Downlink NBR for Priority value 5) . . . . . . . . . . . . . 1360
NBRForPri5UL (Uplink NBR for Priority value 5) . . . . . . . . . . . . . . . 1361
NBRForPri6DL (Downlink NBR for Priority value 6) . . . . . . . . . . . . . 1362
NBRForPri6UL (Uplink NBR for Priority value 6) . . . . . . . . . . . . . . . 1363
NBRForPri7DL (Downlink NBR for Priority value 7) . . . . . . . . . . . . . 1364
NBRForPri7UL (Uplink NBR for Priority value 7) . . . . . . . . . . . . . . . 1365
NBRForPri8DL (Downlink NBR for Priority value 8) . . . . . . . . . . . . . 1366
NBRForPri8UL (Uplink NBR for Priority value 8) . . . . . . . . . . . . . . . 1367
NBRForPri9DL (Downlink NBR for Priority value 9) . . . . . . . . . . . . . 1368
NBRForPri9UL (Uplink NBR for Priority value 9) . . . . . . . . . . . . . . . 1369
HSPDSCHAdjustPeriod (HS-PDSCH code adjustment period) . . . . 1370
HappyBitDelayConditionEDCH (Happy bit delay condition for E-DCH) . .
1371
HsdschGuardTimerHO (HS-DSCH guard time after switching to DCH due
to HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1372
InacUserNbrXXXOverNRT (Inactive users number in XXX over NRT) . .
1374
InacUsersOverloadFact (Inactive users overload preventive factor) 1374
InitialSPINRT (Initial SPI for PS NRT RAB) . . . . . . . . . . . . . . . . . . . 1376
MACdflowthroughputRelThr (Low throughput threshold of the MAC-d flow)
1378
MACdflowthroughputTimetoTrigger (Low throughput time to trigger of the
MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1379
MACdflowtputStrTtT (Low throughput time to trigger of streaming MAC-d
flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1380
MACdflowutilStrTtT (Low util time to trigger of MAC-d flow for streaming)
1381
MEHCQIFeedbackCycle (Temporary CQI feedback cycle for the Mass
Id:0900d80580931b1d
Confidential
93
Radio Network Parameters in Flexi Direct
Table 899
Table 900
Table 901
Table 902
Table 903
Table 904
Table 905
Table 906
Table 907
Table 908
Table 909
Table 910
Table 911
Table 912
Table 913
Table 914
Table 915
Table 916
Table 917
Table 918
Table 919
Table 920
Table 921
Table 922
Table 923
Table 924
Table 925
Table 926
Table 927
94
Event Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1382
MEHHSUPAUserIncr (HSUPA user increment for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1384
MaxBitRateNRTMACDFlow (Maximum bit rate of NRT MAC-d flow) 1385
MaxCSDelayRNCETTI10 (Max buffer time of the HS CS voice in RNC ETTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1387
MaxCSDelayRNCETTI2 (Max buffer time of the HS CS voice in RNC E-TTI
2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1389
MaxCSDelayUE (Max buffer time of the HS CS voice in UE) . . . . . . 1390
MaxEHARQReTxCSAMR10 (E-DCH max number of retransmissions CS
voice E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1391
MaxEHARQReTxCSAMR2 (E-DCH max number of retransmissions CS
voice E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1392
MaxEHARQReTxPSconv10 (E-DCH max number of retransmissions PS
conv E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1393
MaxEHARQReTxPSconv2 (E-DCH max number of retransmissions PS
conv E-TTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1394
MaxReWaitTime (Maximum Reordering Wait Time for MAC-es) . . . 1395
MaxReWaitTime2msTTI (Maximum Reordering Wait Time for Mac-es EDCH 2ms TTI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1396
MaxReWaitTime2msTTI16 (Maximum reordering wait time parameter for
MAC-es E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1397
MaxReWaitTimeRT (Maximum MAC-es Reordering Wait time for RT user)
1398
MaxSetOfEDPDCHCSAMR10 (Maximum Set of E-DPDCHs for CS voice
E-TTI 10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1399
MaxSetOfEDPDCHCSAMR2 (Maximum Set of E-DPDCHs for CS voice ETTI 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400
NRTRBBRWithEDCHStr (NRT RB user bit rate with E-DCH streaming) .
1401
PTTRLCPDUSizeHSDSCH (RLC PDU size for PTT mapped to HSDSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1403
PeriodicityForSI (Periodicity for scheduling info) . . . . . . . . . . . . . . . . 1404
PowerOffsetEHARQPSConv (HARQ power offset for E-DCH MAC-d flow
of PS conv) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1405
PowerOffsetEHARQVoice (HARQ power offset for E-DCH MAC-d flow of
CS voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1406
PowerOffsetForSI (Power Offset for Scheduling Info) . . . . . . . . . . . . 1407
RNHSPAChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . 1408
RNHSPAId (RNHSPA Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1409
SmartHSPATimeToTrigger (Time-to-trigger for Smartphone throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410
SmartHSPATputAveWin (Window size for Smartphone throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1411
T1HSCSVoice (HSDPA re-ordering release timer T1 for the CS voice) . .
1412
T1HSFACH (HSDPA re-ordering release timer T1 for xCCH on HS-FACH)
1413
T1PTT (HSDPA re-ordering rel timer T1 for the PTT) . . . . . . . . . . . . 1414
TGPLAMRHSDPAInterFreq (TGPL for AMR and HSDPA and IF
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 928
Table 929
Table 930
Table 931
Table 932
Table 933
Table 934
Table 935
Table 936
Table 937
Table 938
Table 939
Table 940
Table 941
Table 942
Table 943
Table 944
Table 945
Table 946
Table 947
Table 948
Table 949
Table 950
Table 951
Table 952
Table 953
Table 954
Table 955
Table 956
Table 957
Table 958
Table 959
Table 960
Table 961
DN70456011
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1416
TGPLHSDPAInterFreq (TGPL for HSDPA and IF measurement) . . 1417
ThresholdMaxEDPDCHSR (Threshold to define maximum E-DPDCH SR)
1418
ThresholdMaxEDPDCHSR1920kbps (Threshold to define maximum EDPDCH SR 1920 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1419
ThresholdMaxEDPDCHSR3840kbps (Threshold to define maximum EDPDCH SR 3840 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1420
ThresholdMaxEDPDCHSR960kbps (Threshold to define maximum EDPDCH SR 960 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1422
UPResAllocInCellDCHWait (Retry time for u-plane resource allocation in
Cell_DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1423
VCPHSDPAPrevDuration (Duration of HSDPA prevention for Voice Call
Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1425
VCPHSDPAUserIncr (HSDPA user increment for the Voice Call Priority)
1426
WeightDCH (Weight of NRT DCH UE) . . . . . . . . . . . . . . . . . . . . . . . 1428
WeightDCHBG (Weight of NRT DCH UE BG RAB) . . . . . . . . . . . . . 1429
WeightDCHTHP1 (Weight of NRT DCH UE THP1 RAB) . . . . . . . . . 1430
WeightDCHTHP2 (Weight of NRT DCH UE THP2 RAB) . . . . . . . . . 1431
WeightDCHTHP3 (Weight of NRT DCH UE THP3 RAB) . . . . . . . . . 1432
WeightHSPA (Weight of HSPA UE) . . . . . . . . . . . . . . . . . . . . . . . . . 1433
WeightHSPABG (Weight of HSPA UE BG RAB) . . . . . . . . . . . . . . . 1434
WeightHSPATHP1 (Weight of HSPA UE THP1 RAB) . . . . . . . . . . . 1435
WeightHSPATHP2 (Weight of HSPA UE THP2 RAB) . . . . . . . . . . . 1436
WeightHSPATHP3 (Weight of HSPA UE THP3 RAB) . . . . . . . . . . . 1437
AnchorFmciIdentifier (Anchor FMCI Identifier) . . . . . . . . . . . . . . . . . 1439
AnchorFmcsIdentifier (Anchor FMCS Identifier) . . . . . . . . . . . . . . . . 1439
AnchorHopiIdentifier (Anchor HOPI Identifier) . . . . . . . . . . . . . . . . . 1440
AnchorHopsIdentifier (Anchor HOPS Identifier) . . . . . . . . . . . . . . . . 1441
BlindGsmHoCS (Blind GSM handover for CS RAB) . . . . . . . . . . . . . 1442
CUCEcNoThresholdCSEHO (CPICH Ec/No Threshold Value For CUC Usage in CSEHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1443
CellReselectionObservingTime (Cell Reselection Observing Time) . 1445
DRRCForHSDPALayerServices (Services for DRRC connection setup for
HSDPA layer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1447
DefaultAuthorisedNetworkId (Identifier of the Default Authorised Network)
1448
DirectPchDchCS (Cell/URA_PCH to Cell_DCH transition due to CS call)
1449
DirectedRRCForHSDPALayerEnhanc (DRRC connection setup for HSDPA layer enhancements) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450
DisablePowerInHSDPALayeringDecision (Disable power in decision making for HSDPA layering) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1452
EcnoDifferenceThreshold (CPICH EcNo Difference Threshold) . . . . 1453
EnableULQualDetRep (Quality deterioration report from UL OLPC
controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1454
FastDormOverCpcPri (Fast Dormancy and CPC priority) . . . . . . . . 1455
FastUECancel (Fast UE Cancellation) . . . . . . . . . . . . . . . . . . . . . . . 1456
Id:0900d80580931b1d
Confidential
95
Radio Network Parameters in Flexi Direct
Table 962
Table 963
Table 964
Table 965
Table 966
Table 967
Table 968
Table 969
Table 970
Table 971
Table 972
Table 973
Table 974
Table 975
Table 976
Table 977
Table 978
Table 979
Table 980
Table 981
Table 982
Table 983
Table 984
Table 985
Table 986
Table 987
Table 988
Table 989
Table 990
Table 991
Table 992
Table 993
Table 994
96
FastUEPeriod (Fast UE evaluation period) . . . . . . . . . . . . . . . . . . . . 1457
FastUEThreshold (Fast UE Threshold) . . . . . . . . . . . . . . . . . . . . . . . 1458
GANetwARFCN (GAN ARFCN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1459
GANetwBCC (GAN BCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1460
GANetwNCC (GAN NCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1461
GapPositionSingleFrame (Gap position single frame) . . . . . . . . . . . . 1462
GsmHandoverAMR (Handover of AMR Service to GSM) . . . . . . . . . 1463
GsmHandoverCS (Handover of CS Service to GSM) . . . . . . . . . . . . 1464
GsmHandoverNrtPS (Handover of NRT PS Service to GSM) . . . . . . 1465
GsmHandoverRtPS (Handover of RT PS Service to GSM) . . . . . . . . 1467
HSCAHORabCombSupport (RAB Combinations Supported by HSCAHO)
1468
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1469
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1471
HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1472
HSDPALayerLoadShareThreshold (HSDPA layers load sharing
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1473
HSDPASIRErrorAveWindow (Averaging window of the SIRerror
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1475
HSDPASIRErrorFilterCoefficient (Higher layer filtering coefficient for HSDPA SIRerror) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1476
HSDPASIRErrorReportPeriod (Reporting period of the SIRerror
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1477
HSDPASIRErrorServCell (SIRerror threshold for the serving HS-DSCH
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1478
HSDPASIRErrorTargetCell (SIRerror threshold for the target cell) . . 1479
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1480
HSPADRNCEcNoOffset (DRNC Ec/No offset for HSPA Inter-RNC Cell
Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1482
HSPADRNCSIRErrorOffset (SIR error offset for HSPA Inter-RNC Cell
Change) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1483
IBTSRabCombSupport (RAB Combinations Supported by FD-BTS) 1484
LHOMinNrtDchAllocTime (Load handover minimum NRT DCH allocation
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1486
LowerRxTxTimeDiff (Lower Rx-Tx Time Difference Threshold) . . . . 1486
MBLBGuardTimer (MBLB Guard Timer) . . . . . . . . . . . . . . . . . . . . . . 1487
MaxBLHOAttempt (Maximum Number of BLHO Attempts) . . . . . . . . 1488
MaxCellReselections (Max cell reselections) . . . . . . . . . . . . . . . . . . . 1489
MaxNumISHOClPerAS (Max Number of ISHO Cancellations Per Active
Set for a U) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1491
MultipleBSICIdent (Multiple BSIC Identification) . . . . . . . . . . . . . . . . 1491
NCHOFilterCoeffComLoadMeasDRNCCell (NCHO filter coefficient common load meas DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1492
NCHOHystComLoadMeasDRNCCell (NCHO hysteresis common load
measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1494
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 995
Table 996
Table 997
Table 998
Table 999
Table 1000
Table 1001
Table 1002
Table 1003
Table 1004
Table 1005
Table 1006
Table 1007
Table 1008
Table 1009
Table 1010
Table 1011
Table 1012
Table 1013
Table 1014
Table 1015
Table 1016
Table 1017
Table 1018
Table 1019
Table 1020
Table 1021
Table 1022
Table 1023
DN70456011
NCHOThrComLoadMeasDRNCCell (NCHO threshold common load measurement DRNC cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1495
PagingGroupList (List of FD-BTS in paging group) . . . . . . . . . . . . . 1497
PgRncId (Paging Group member I-BTS RNC-ID) . . . . . . . . . . . . . . . 1498
PagingRoleType (Current Role of FD-BTS) . . . . . . . . . . . . . . . . . . . 1498
PreferBandForLayering (Preferred Band for Layering) . . . . . . . . . . . 1499
RANAPCauseLoadHO (RANAP cause to indicate load handover) . 1500
RANAPCause1LoadHO (RANAP cause 1 to indicate load handover) . . .
1501
RANAPCause2LoadHO (RANAP cause 2 to indicate load handover) . . .
1502
RANAPCause3LoadHO (RANAP cause 3 to indicate load handover) . . .
1503
RANAPCauseServHO (RANAP cause to indicate service handover) 1504
RANAPCause1ServHO (RANAP cause 1 to indicate service handover) .
1505
RANAPCause2ServHO (RANAP cause 2 to indicate service handover) .
1506
RANAPCause3ServHO (RANAP cause 3 to indicate service handover) .
1507
RNMOBIChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . 1508
RNMOBIId (RNMOBI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1509
SLHOHandlingOfCellLoadMeasNotAct (SLHO handling of cell load measurement is not active) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1510
SLHOProfileBackgroundPSNRTData (Service profile for background PS
NRT data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1512
SLHOProfileConvCSSpeech (Service profile for conversational CS speech
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1513
SLHOProfileConvCSTData (Service profile for conversational CS T data in
SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1515
SLHOProfileConvPSRTData (Service profile for conversational PS RT
data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1517
SLHOProfileConvPSSpeech (Service profile for conversational PS speech
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1519
SLHOProfileInteractivePSNRTData (Service profile for interactive PS NRT
data in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1521
SLHOProfileStreamCSNTData (Service profile for streaming CS NT data
in SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1523
SLHOProfileStreamPSRTData (Service profile for streaming PS RT data in
SLHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1525
SLHOUseBackgroundPSNRTData (Use of SLHO for background PS NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1527
SLHOUseConvCSSpeech (Use of SLHO for conversational CS speech)
1529
SLHOUseConvCSTData (Use of SLHO for conversational CS transparent
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1530
SLHOUseConvPSRTData (Use of SLHO for conversational PS RT data)
1532
SLHOUseConvPSSpeech (Use of SLHO for conversational PS speech)
1533
Id:0900d80580931b1d
Confidential
97
Radio Network Parameters in Flexi Direct
Table 1024 SLHOUseInteractivePSNRTData (Use of SLHO for interactive PS NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1535
Table 1025 SLHOUseStreamCSNTData (Use of SLHO for streaming CS non-transparent data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1536
Table 1026 SLHOUseStreamPSRTData (Use of SLHO for streaming PS RT data) . .
1538
Table 1027 ServBtwnHSDPALayers (Services between HSDPA layers) . . . . . . . 1539
Table 1028 ServicesToHSDPALayer (Services to HSDPA layer in state transition) . .
1540
Table 1029 SmartLTELayeringPrevT (Timer for Smart LTE Layering Prevention) . . .
1541
Table 1030 SmartLTELayeringServ (Smart LTE Layering service control) . . . . . 1542
Table 1031 TGPLdoubleframeNRTPSgsm (Transmision gap pattern length in case of
double frame: NRT PS service and GSM measurement) . . . . . . . . . 1544
Table 1032 TGPLdoubleframeNRTPSinterFreq (Transmision gap pattern length in
case of double frame: NRT PS service and IF measurement) . . . . . 1545
Table 1033 TGPLsingleframeAMRgsm (Transmision gap pattern length in case of single frame: AMR service and GSM measurement) . . . . . . . . . . . . . . . 1546
Table 1034 TGPLsingleframeAMRinterFreq (Transmision gap pattern length in case of
single frame: AMR service and IF measurement) . . . . . . . . . . . . . . . 1547
Table 1035 TGPLsingleframeCSgsm (Transmision gap pattern length in case of single
frame: CS service and GSM measurement) . . . . . . . . . . . . . . . . . . . 1548
Table 1036 TGPLsingleframeCSinterFreq (Transmision gap pattern length in case of
single frame: CS service and IF measurement) . . . . . . . . . . . . . . . . . 1549
Table 1037 TGPLsingleframeNRTPSgsm (Transmision gap pattern length in case of
single frame: NRT PS service and GSM measurement) . . . . . . . . . . 1550
Table 1038 TGPLsingleframeNRTPSinterFreq (Transmision gap pattern length in case
of single frame: NRT PS service and IF measurement) . . . . . . . . . . 1551
Table 1039 TGPLsingleframeRTPSgsm (Transmision gap pattern length in case of
single frame: RT PS service and GSM measurement) . . . . . . . . . . . 1552
Table 1040 TGPLsingleframeRTPSinterFreq (Transmision gap pattern length in case
of single frame: RT PS service and IF measurement) . . . . . . . . . . . . 1553
Table 1041 TRelocOverall (T RelocOverall) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1554
Table 1042 TRelocPrep (T RelocPrep) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1555
Table 1043 UEQualityRepInterv (UE Quality Measurement Reporting Interval) . 1555
Table 1044 UETxPowerMaxRef (Maximum Reference UE transmission power) . 1557
Table 1045 ULQualDetRepThreshold (UL quality deterioration reporting threshold) . .
1558
Table 1046 UpperRxTxTimeDiff (Upper Rx-Tx Time Difference Threshold) . . . . 1559
Table 1047 ActivationTimeOffset (Offset for activation time) . . . . . . . . . . . . . . . . 1560
Table 1048 CellDCHtestTmr (Test timer for inactivity supervision in Cell_DCH state) .
1561
Table 1049 CrQueuingTimeDL (Maximum downlink capacity request queuing time) .
1562
Table 1050 CrQueuingTimeUL (Maximum uplink capacity request queuing time) 1563
Table 1051 DCHUtilBelowDowngradeThr (Threshold below the downgrade bit rate) .
1564
Table 1052 DCHUtilHighAveWin (Window size for the high throughput measurement)
1566
Table 1053 DCHUtilHighBelowNRTDataRateThr (Threshold below the NRT DCH data
98
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1567
Table 1054 DCHUtilHighTimeToTrigger (Time to trigger for the high throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1569
Table 1055 DCHUtilLowerAveWinBitRate (Window size for the lower throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1570
Table 1056 DCHUtilLowerAveWin128 (Lower measurement window size for NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1572
Table 1057 DCHUtilLowerAveWin256 (Lower measurement window size for NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1574
Table 1058 DCHUtilLowerAveWin32 (Lower measurement window size for NRT DCH
of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1576
Table 1059 DCHUtilLowerAveWin384 (Lower measurement window size for NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1578
Table 1060 DCHUtilLowerAveWin64 (Lower measurement window size for NRT DCH
of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1580
Table 1061 DCHUtilLowerDowngradeThrBitRate (Lower downgrade threshold) 1582
Table 1062 DCHUtilLowerDowngradeThr128 (Lower downgrade threshold for the NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1584
Table 1063 DCHUtilLowerDowngradeThr256 (Lower downgrade threshold for the NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1586
Table 1064 DCHUtilLowerDowngradeThr32 (Lower downgrade threshold for the NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1587
Table 1065 DCHUtilLowerDowngradeThr384 (Lower downgrade threshold for the NRT
DCH of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1588
Table 1066 DCHUtilLowerDowngradeThr64 (Lower downgrade threshold for the NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1589
Table 1067 DCHUtilLowerTimeToTriggerBitRate (Time to trigger for the lower throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1591
Table 1068 DCHUtilLowerTimeToTrigger128 (Lower time to trigger for the NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1593
Table 1069 DCHUtilLowerTimeToTrigger256 (Lower time to trigger for the NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1594
Table 1070 DCHUtilLowerTimeToTrigger32 (Lower time to trigger for the NRT DCH of
32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1595
Table 1071 DCHUtilLowerTimeToTrigger384 (Lower time to trigger for the NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1596
Table 1072 DCHUtilLowerTimeToTrigger64 (Lower time to trigger for the NRT DCH of
64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1597
Table 1073 DCHUtilMeasGuardTime (Guard time for throughput measurement) 1598
Table 1074 DCHUtilUpperAveWinBitRate (Window size for the upper throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1599
Table 1075 DCHUtilUpperAveWin128 (Upper measurement window size for NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1601
Table 1076 DCHUtilUpperAveWin256 (Upper measurement window size for NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1603
Table 1077 DCHUtilUpperAveWin32 (Upper measurement window size for NRT DCH
of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1605
Table 1078 DCHUtilUpperAveWin384 (Upper measurement window size for NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1607
Table 1079 DCHUtilUpperAveWin64 (Upper measurement window size for NRT DCH
of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1609
DN70456011
Id:0900d80580931b1d
Confidential
99
Radio Network Parameters in Flexi Direct
Table 1080 DCHUtilUpperDowngradeThrBitRate (Upper downgrade threshold) . 1611
Table 1081 DCHUtilUpperDowngradeThr128 (Upper downgrade threshold for the NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1613
Table 1082 DCHUtilUpperDowngradeThr256 (Upper downgrade threshold for the NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1615
Table 1083 DCHUtilUpperDowngradeThr32 (Upper downgrade threshold for the NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1616
Table 1084 DCHUtilUpperDowngradeThr384 (Upper downgrade threshold for the NRT
DCH of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1617
Table 1085 DCHUtilUpperDowngradeThr64 (Upper downgrade threshold for the NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1618
Table 1086 DCHUtilUpperTimeToTriggerBitRate (Time to trigger for the upper
throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1619
Table 1087 DCHUtilUpperTimeToTrigger128 (Upper time to trigger for the NRT DCH
of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1621
Table 1088 DCHUtilUpperTimeToTrigger256 (Upper time to trigger for the NRT DCH
of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1622
Table 1089 DCHUtilUpperTimeToTrigger32 (Upper time to trigger for the NRT DCH of
32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1623
Table 1090 DCHUtilUpperTimeToTrigger384 (Upper time to trigger for the NRT DCH
of 384 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1624
Table 1091 DCHUtilUpperTimeToTrigger64 (Upper time to trigger for the NRT DCH of
64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1625
Table 1092 DLOptimisationProhibitTime (Dynamic Link Optimisation prohibit time) . .
1626
Table 1093 DLOptimisationPwrOffset (Power offset for dynamic link optimisation) . . .
1627
Table 1094 FactorMinPBSinterval (Factor to determine minimum PBS interval) . 1628
Table 1095 HSFACHDiscardTimerDTCH (Discard Timer for DTCH data on HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1629
Table 1096 HSFACHRestTimerDTCH (MAC-ehs Reset Timer for DTCH data on HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1630
Table 1097 InactDetForStreamingRB (Inactivation detection for streaming radio
bearer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1631
Table 1098 IurPriority (Priority handling over Iur-interface) . . . . . . . . . . . . . . . . . 1633
Table 1099 MEHTVMPendingTime (Temporary TVM pending time for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1634
Table 1100 PTTDormancyTimer (PTT dormancy timer) . . . . . . . . . . . . . . . . . . . . 1635
Table 1101 QoSPriorityMapping (QoS Priority Mapping) . . . . . . . . . . . . . . . . . . . 1636
Table 1102 PriForBackARP1 (Priority for Background TC with ARP 1) . . . . . . . . 1640
Table 1103 PriForBackARP2 (Priority for Background TC with ARP 2) . . . . . . . . 1641
Table 1104 PriForBackARP3 (Priority for Background TC with ARP 3) . . . . . . . . 1642
Table 1105 PriForConvOnHSPA (Priority for conversational on HSPA) . . . . . . . 1643
Table 1106 PriForHSFACHDTCH (Priority for PS data over HSPA on CELL_FACH
state.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1644
Table 1107 PriForIntSignaling (Priority for Interactive TC marked for signaling use) . .
1645
Table 1108 PriForIntTHP1ARP1 (Priority for Interactive TC with THP 1 and ARP 1) .
1646
Table 1109 PriForIntTHP1ARP2 (Priority for Interactive TC with THP 1 and ARP 2) .
100
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
1647
Table 1110 PriForIntTHP1ARP3 (Priority for Interactive TC with THP 1 and ARP 3) .
1649
Table 1111 PriForIntTHP2ARP1 (Priority for Interactive TC with THP 2 and ARP 1) .
1650
Table 1112 PriForIntTHP2ARP2 (Priority for Interactive TC with THP 2 and ARP 2) .
1651
Table 1113 PriForIntTHP2ARP3 (Priority for Interactive TC with THP 2 and ARP 3) .
1652
Table 1114 PriForIntTHP3ARP1 (Priority for Interactive TC with THP 3 and ARP 1) .
1653
Table 1115 PriForIntTHP3ARP2 (Priority for Interactive TC with THP 3 and ARP 2) .
1654
Table 1116 PriForIntTHP3ARP3 (Priority for Interactive TC with THP 3 and ARP 3) .
1655
Table 1117 PriForSRBsOnHSPA (Priority for SRBs on HSPA) . . . . . . . . . . . . . . 1657
Table 1118 PriForStreamARP1 (Priority for Streaming traffic class with ARP1) . 1658
Table 1119 PriForStreamARP2 (Priority for Streaming traffic class with ARP2) . 1659
Table 1120 PriForStreamARP3 (Priority for Streaming traffic class with ARP3) . 1661
Table 1121 RNPSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 1662
Table 1122 RNPSId (RNPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1663
Table 1123 RTOverNRTPriThresholdARP1 (RT-over-NRT priority threshold for
ARP1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1664
Table 1124 RTOverNRTPriThresholdARP2 (RT-over-NRT priority threshold for
ARP2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1665
Table 1125 RTOverNRTPriThresholdARP3 (RT-over-NRT priority threshold for
ARP3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1667
Table 1126 RoleSwitchActAdjOffset (Role Switch activation adjustment offset) . 1668
Table 1127 SmartInactTimerFACH (Inactivity Timer for Smart Phones in Cell_FACH)
1668
Table 1128 SmartInactivityTimerDCH (Inactivity timer for Smartphone DCH) . . 1669
Table 1129 ToCellFACHinTest (Test switch for Iu release in Cell_DCH state) . . 1670
Table 1130 TrafVolThresholdDLHigh (Downlink traffic volume measurement high
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1671
Table 1131 TrafVolThresholdDLHighBitRate (Traffic volume threshold for downlink
NRT DCH bit rates) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1674
Table 1132 TrafVolThresholdDLHighDCH128 (Traffic volume threshold for DL NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1676
Table 1133 TrafVolThresholdDLHighDCH16 (Traffic volume threshold for DL NRT
DCH of 16 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1678
Table 1134 TrafVolThresholdDLHighDCH256 (Traffic volume threshold for DL NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1680
Table 1135 TrafVolThresholdDLHighDCH32 (Traffic volume threshold for DL NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1682
Table 1136 TrafVolThresholdDLHighDCH64 (Traffic volume threshold for DL NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1684
Table 1137 TrafVolThresholdDLHighDCH8 (Traffic volume threshold for DL NRT DCH
of 8 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1686
Table 1138 TrafVolThresholdULHigh (Uplink traffic volume measurement high
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1687
DN70456011
Id:0900d80580931b1d
Confidential
101
Radio Network Parameters in Flexi Direct
Table 1139 TrafVolThresholdULHighBitRate (Traffic volume threshold for uplink NRT
DCH bit rates) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1690
Table 1140 TrafVolThresholdULHighDCH128 (Traffic volume threshold for UL NRT
DCH of 128 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1692
Table 1141 TrafVolThresholdULHighDCH16 (Traffic volume threshold for UL NRT
DCH of 16 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1694
Table 1142 TrafVolThresholdULHighDCH256 (Traffic volume threshold for UL NRT
DCH of 256 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1696
Table 1143 TrafVolThresholdULHighDCH32 (Traffic volume threshold for UL NRT
DCH of 32 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1697
Table 1144 TrafVolThresholdULHighDCH64 (Traffic volume threshold for UL NRT
DCH of 64 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1699
Table 1145 TrafVolThresholdULHighDCH8 (Traffic volume threshold for UL NRT DCH
of 8 kbps) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1700
Table 1146 TrafVolTimeToTriggerDL (Downlink traffic volume measurement time to
trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1702
Table 1147 TrafVolTimeToTriggerUL (Uplink traffic volume measurement time to
trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1703
Table 1148 ULLoadStateTTT (UL loaded state time to trigger) . . . . . . . . . . . . . . 1705
Table 1149 AMRLCBufMaxOverbook2NRT (AM RLC buffer max total overbooking for
2 PS RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1707
Table 1150 AMRLCBufMaxOverbook3NRT (AM RLC buffer max overbooking for more
than 2 PS RABs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1708
Table 1151 AMRLCHSFACHPS (AM RLC configuration for PS NRT with HS-FACH)
1709
Table 1152 AMRLCHSFACHPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1710
Table 1153 AMRLCHSFACHPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1711
Table 1154 AMRLCHSFACHPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1712
Table 1155 AMRLCHSFACHPSPeriodMax (AM RLC status period max for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1714
Table 1156 AMRLCHSFACHPSPeriodMin (AM RLC status period min for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1715
Table 1157 AMRLCHSFACHPSPollPDU (AM RLC period Poll_PDU for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1716
Table 1158 AMRLCHSFACHPSPollSDU (AM RLC period Poll_SDU for PS NRT with
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1718
Table 1159 AMRLCHSFACHPSPollWin (AM RLC period Poll_Window for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1719
Table 1160 AMRLCHSFACHPSTriggers (AM RLC status report triggers for PS NRT
with HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1720
Table 1161 AMRLCRespHSFACHandRACH (AM RLC round trip time with HSDSCH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1722
Table 1162 HSFACHAMRLCRespHSRACH (AM RLC round trip time with HSDSCH/HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1723
Table 1163 AMRLCHSRACHPS (AM RLC configuration for PS NRT with HS-RACH)
1725
Table 1164 AMRLCHSRACHPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1726
102
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1165 AMRLCHSRACHPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1727
Table 1166 AMRLCHSRACHPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1728
Table 1167 AMRLCHSRACHPSPeriodMax (AM RLC status period max for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1729
Table 1168 AMRLCHSRACHPSPeriodMin (AM RLC status period min for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1730
Table 1169 AMRLCHSRACHPSPollPDU (AM RLC period Poll_PDU for PS NRT with
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1731
Table 1170 AMRLCHSRACHPSPollSDU (AM RLC period Poll_SDU for PS NRT with
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1733
Table 1171 AMRLCHSRACHPSPollWin (AM RLC period Poll_Window for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1734
Table 1172 AMRLCHSRACHPSTriggers (AM RLC status report triggers for PS NRT
with HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1735
Table 1173 HSRACHAMRLCRespHSFACH (AM RLC round trip time with HS-RACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1737
Table 1174 AMRLCMaximumBufferUE (AM RLC maximum buffer allocation for UE)
1738
Table 1175 AMRLCMaximumBufferUE100 (AM RLC maximum buffer allocation for UE
capability 100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1740
Table 1176 AMRLCMaximumBufferUE1150 (AM RLC maximum buffer allocation for
UE capability 1150) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1740
Table 1177 AMRLCMaximumBufferUE1250 (AM RLC maximum buffer allocation for
UE capability 1250) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1742
Table 1178 AMRLCMaximumBufferUE150 (AM RLC maximum buffer allocation for UE
capability 150) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1743
Table 1179 AMRLCMaximumBufferUE1k (AM RLC maximum buffer allocation for UE
capability 1000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1743
Table 1180 AMRLCMaximumBufferUE200 (AM RLC maximum buffer allocation for UE
capability 200) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1745
Table 1181 AMRLCMaximumBufferUE300 (AM RLC maximum buffer allocation for UE
capability 300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1745
Table 1182 AMRLCMaximumBufferUE50 (AM RLC maximum buffer allocation for UE
capability 50) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1747
Table 1183 AMRLCMaximumBufferUE500 (AM RLC maximum buffer allocation for UE
capability 500) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1747
Table 1184 AMRLCMaximumBufferUE750 (AM RLC maximum buffer allocation for UE
capability 750) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1749
Table 1185 AMRLCmaximumBufferUE400 (AM RLC maximum buffer allocation for UE
capability 400) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750
Table 1186 AMRLCOnDCHOfNRTPS (AM RLC configuration for PS NRT with DCH)
1751
Table 1187 AMRLCOnDCHOfNRTPSCount (AM RLC status reports count for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1752
Table 1188 AMRLCOnDCHOfNRTPSFilterReTX (AM RLC retransmission filter for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1754
Table 1189 AMRLCOnDCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1755
Table 1190 AMRLCOnDCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions for
DN70456011
Id:0900d80580931b1d
Confidential
103
Radio Network Parameters in Flexi Direct
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1757
Table 1191 AMRLCOnDCHOfNRTPSMaxRST (AM RLC MaxRST transmissions for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1758
Table 1192 AMRLCOnDCHOfNRTPSPeriodMax (AM RLC status period max for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1759
Table 1193 AMRLCOnDCHOfNRTPSPeriodMin (AM RLC status period min for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1760
Table 1194 AMRLCOnDCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1761
Table 1195 AMRLCOnDCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS NRT
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1763
Table 1196 AMRLCOnDCHOfNRTPSPollWindow (AM RLC period Poll_Window for
PS NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1764
Table 1197 AMRLCOnDCHOfNRTPSTriggers (AM RLC status report triggers for PS
NRT with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1765
Table 1198 AMRLCOnDCHOfSRB136 (AM RLC configuration for SRB13.6 with DCH)
1767
Table 1199 AMRLCOnDCHOfSRB136MaxDAT (AM RLC MaxDAT transmissions for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1768
Table 1200 AMRLCOnDCHOfSRB136PeriodMax (AM RLC status period max for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1769
Table 1201 AMRLCOnDCHOfSRB136PeriodMin (AM RLC status period min for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1771
Table 1202 AMRLCOnDCHOfSRB136PollPDU (AM RLC period Poll_PDU for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1772
Table 1203 AMRLCOnDCHOfSRB136PollSDU (AM RLC period Poll_SDU for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1773
Table 1204 AMRLCOnDCHOfSRB136PollWindow (AM RLC period Poll_Window for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1774
Table 1205 AMRLCOnDCHOfSRB136Triggers (AM RLC status report triggers for
SRB13.6 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1775
Table 1206 AMRLCOnDCHOfSRB34 (AM RLC configuration for SRB3.4 with DCH) .
1777
Table 1207 AMRLCOnDCHOfSRB34MaxDAT (AM RLC MaxDAT transmissions for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1778
Table 1208 AMRLCOnDCHOfSRB34PeriodMax (AM RLC status period max for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1779
Table 1209 AMRLCOnDCHOfSRB34PeriodMin (AM RLC status period min for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1781
Table 1210 AMRLCOnDCHOfSRB34PollPDU (AM RLC period Poll_PDU for SRB3.4
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1782
Table 1211 AMRLCOnDCHOfSRB34PollSDU (AM RLC period Poll_SDU for SRB3.4
with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1783
Table 1212 AMRLCOnDCHOfSRB34PollWindow (AM RLC period Poll_Window for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1784
Table 1213 AMRLCOnDCHOfSRB34Triggers (AM RLC status report triggers for
SRB3.4 with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1785
Table 1214 AMRLCOnDCHOfStream (AM RLC configuration for PS streaming with
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1787
Table 1215 AMRLCOnDCHOfStreamCount (AM RLC status reports count for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1788
104
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1216 AMRLCOnDCHOfStreamDiscardTime (AM RLC SDU discard time for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1790
Table 1217 AMRLCOnDCHOfStreamFilterReTX (AM RLC retransmission filter for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1791
Table 1218 AMRLCOnDCHOfStreamMaxDAT (AM RLC MaxDAT transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1793
Table 1219 AMRLCOnDCHOfStreamMaxMRW (AM RLC MaxMRW transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1794
Table 1220 AMRLCOnDCHOfStreamMaxRST (AM RLC MaxRST transmissions for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1796
Table 1221 AMRLCOnDCHOfStreamPeriodMax (AM RLC status period max for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1797
Table 1222 AMRLCOnDCHOfStreamPeriodMin (AM RLC status period min for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1798
Table 1223 AMRLCOnDCHOfStreamPollPDU (AM RLC period Poll_PDU for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1799
Table 1224 AMRLCOnDCHOfStreamPollSDU (AM RLC period Poll_SDU for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1801
Table 1225 AMRLCOnDCHOfStreamPollWindow (AM RLC period Poll_Window for
PS streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1802
Table 1226 AMRLCOnDCHOfStreamTriggers (AM RLC status report triggers for PS
streaming with DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1803
Table 1227 AMRLCOnEDCHOfNRTPS (AM RLC configuration for PS NRT with EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1805
Table 1228 AMRLCOnEDCHOfNRTPSCount (AM RLC status reports count for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1807
Table 1229 AMRLCOnEDCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1808
Table 1230 AMRLCOnEDCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions
for PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1809
Table 1231 AMRLCOnEDCHOfNRTPSMaxRST (AM RLC maxRST transmissions for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1810
Table 1232 AMRLCOnEDCHOfNRTPSPeriodMax (AM RLC status period max for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1811
Table 1233 AMRLCOnEDCHOfNRTPSPeriodMin (AM RLC status period min for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1813
Table 1234 AMRLCOnEDCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1814
Table 1235 AMRLCOnEDCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1815
Table 1236 AMRLCOnEDCHOfNRTPSPollWindow (AM RLC period Poll_Window for
PS NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1816
Table 1237 AMRLCOnEDCHOfNRTPSTriggers (AM RLC status report triggers for PS
NRT with E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1817
Table 1238 AMRLCOnEDCHOfStrPS (AM RLC configuration for PS streaming with EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1819
Table 1239 EDCHStrPSCount (AM RLC status reports count for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1821
Table 1240 EDCHStrPSDiscardTime (AM RLC SDU discard time for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1822
Table 1241 EDCHStrPSMaxDAT (AM RLC MaxDAT transmissions for PS streaming
DN70456011
Id:0900d80580931b1d
Confidential
105
Radio Network Parameters in Flexi Direct
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1824
Table 1242 EDCHStrPSMaxMRW (AM RLC MaxMRW transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1825
Table 1243 EDCHStrPSMaxRST (AM RLC maxRST transmissions for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1826
Table 1244 EDCHStrPSPeriodMax (AM RLC status period max for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1827
Table 1245 EDCHStrPSPeriodMin (AM RLC status period min for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1828
Table 1246 EDCHStrPSPollPDU (AM RLC period Poll_PDU for PS streaming E-DCH)
1829
Table 1247 EDCHStrPSPollSDU (AM RLC period Poll_SDU for PS streaming E-DCH)
1830
Table 1248 EDCHStrPSPollWindow (AM RLC period Poll_Window for PS streaming
E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1831
Table 1249 EDCHStrPSTriggers (AM RLC status report triggers for PS streaming EDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1832
Table 1250 AMRLCOnFACHOfPS (AM RLC configuration for PS NRT with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1834
Table 1251 AMRLCOnFACHOfPSMaxDAT (AM RLC MaxDAT transmissions for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1836
Table 1252 AMRLCOnFACHOfPSMaxMRW (AM RLC MaxMRW transmissions for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1837
Table 1253 AMRLCOnFACHOfPSMaxRST (AM RLC MaxRST transmissions for PS
NRT with FACH/RAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1838
Table 1254 AMRLCOnFACHOfPSPeriodMax (AM RLC status period max for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1839
Table 1255 AMRLCOnFACHOfPSPeriodMin (AM RLC status period min for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1840
Table 1256 AMRLCOnFACHOfPSPollPDU (AM RLC period Poll_PDU for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1841
Table 1257 AMRLCOnFACHOfPSPollSDU (AM RLC period Poll_SDU for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1842
Table 1258 AMRLCOnFACHOfPSPollWindow (AM RLC period Poll_Window for PS
NRT with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1843
Table 1259 AMRLCOnFACHOfPSTriggers (AM RLC status report triggers for PS NRT
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1845
Table 1260 AMRLCOnFACHOfSRB (AM RLC configuration for SRB with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1847
Table 1261 AMRLCOnFACHOfSRBMaxDAT (AM RLC MaxDAT transmissions for
SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1848
Table 1262 AMRLCOnFACHOfSRBPeriodMax (AM RLC status period max for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1849
Table 1263 AMRLCOnFACHOfSRBPeriodMin (AM RLC status period min for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1851
Table 1264 AMRLCOnFACHOfSRBPollPDU (AM RLC period Poll_PDU for SRB with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1852
Table 1265 AMRLCOnFACHOfSRBPollSDU (AM RLC period Poll_SDU for SRB with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1853
Table 1266 AMRLCOnFACHOfSRBPollWindow (AM RLC period Poll_Window for
SRB with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1854
106
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1267 AMRLCOnFACHOfSRBTriggers (AM RLC status report triggers for SRB
with FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1855
Table 1268 AMRLCOnHSDSCHOfNRTPS (AM RLC configuration for PS NRT with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1857
Table 1269 AMRLCOnHSDSCHOfNRTPSCount (AM RLC status reports count for PS
NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1858
Table 1270 AMRLCOnHSDSCHOfNRTPSFilterReTX (AM RLC retransmission filter
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1860
Table 1271 AMRLCOnHSDSCHOfNRTPSMaxDAT (AM RLC MaxDAT transmissions
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1861
Table 1272 AMRLCOnHSDSCHOfNRTPSMaxMRW (AM RLC MaxMRW transmissions for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . 1862
Table 1273 AMRLCOnHSDSCHOfNRTPSMaxRST (AM RLC maxRST transmissions
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1863
Table 1274 AMRLCOnHSDSCHOfNRTPSPeriodMax (AM RLC status period max for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1864
Table 1275 AMRLCOnHSDSCHOfNRTPSPeriodMin (AM RLC status period min for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1866
Table 1276 AMRLCOnHSDSCHOfNRTPSPollPDU (AM RLC period Poll_PDU for PS
NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1867
Table 1277 AMRLCOnHSDSCHOfNRTPSPollSDU (AM RLC period Poll_SDU for PS
NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1868
Table 1278 AMRLCOnHSDSCHOfNRTPSPollWindow (AM RLC period Poll_Window
for PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1869
Table 1279 AMRLCOnHSDSCHOfNRTPSTriggers (AM RLC status report triggers for
PS NRT with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1870
Table 1280 AMRLCOnHSDSCHOfStrPS (AM RLC configuration for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1872
Table 1281 HSDSCHStrDiscardTime (AM RLC SDU discard time for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1874
Table 1282 HSDSCHStrPSCount (AM RLC status reports count for PS stream with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1875
Table 1283 HSDSCHStrPSFilterReTX (AM RLC retransmission filter for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1877
Table 1284 HSDSCHStrPSMaxDAT (AM RLC MaxDAT transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1878
Table 1285 HSDSCHStrPSMaxMRW (AM RLC MaxMRW transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1879
Table 1286 HSDSCHStrPSMaxRST (AM RLC maxRST transmissions for PS stream
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1880
Table 1287 HSDSCHStrPSPeriodMax (AM RLC status period max for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1881
Table 1288 HSDSCHStrPSPeriodMin (AM RLC status period min for PS streaming
with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1882
Table 1289 HSDSCHStrPSPollPDU (AM RLC period Poll_PDU for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1883
Table 1290 HSDSCHStrPSPollSDU (AM RLC period Poll_SDU for PS streaming with
HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1885
Table 1291 HSDSCHStrPSPollWindow (AM RLC period Poll_Window for PS streaming with HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1886
Table 1292 HSDSCHStrPSTriggers (AM RLC status report triggers for PS str with HS-
DN70456011
Id:0900d80580931b1d
Confidential
107
Radio Network Parameters in Flexi Direct
DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1887
Table 1293 AMRLCPeriodMaxHSSRB (AM RLC status period max for SRBs with HSRACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1889
Table 1294 AMRLCRelatTXWindow (AM RLC relative transmission window sizes) . .
1891
Table 1295 AMRLCRelatTXWindowRate1 (AM RLC relative Tx window size defining
data rate 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1892
Table 1296 AMRLCRelatTXWindowRate1Size (AM RLC relative Tx window size assigned to data rate 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1893
Table 1297 AMRLCRelatTXWindowRate2 (AM RLC relative Tx window size defining
data rate 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1894
Table 1298 AMRLCRelatTXWindowRate2Size (AM RLC relative Tx window size assigned to data rate 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1895
Table 1299 AMRLCRelatTXWindowRate3 (AM RLC relative Tx window size defining
data rate 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1896
Table 1300 AMRLCRelatTXWindowRate3Size (AM RLC relative Tx window size assigned to data rate 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1897
Table 1301 AMRLCRelatTXWindowRate4 (AM RLC relative Tx window size defining
data rate 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1898
Table 1302 AMRLCRelatTXWindowRate4Size (AM RLC relative Tx window size assigned to data rate 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1899
Table 1303 AMRLCRelatTXWindowRate5 (AM RLC relative Tx window size defining
data rate 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1900
Table 1304 AMRLCRelatTXWindowRate5Size (AM RLC relative Tx window size assigned to data rate 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1901
Table 1305 AMRLCRelatTXWindowRate6 (AM RLC relative Tx window size defining
data rate 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1902
Table 1306 AMRLCRelatTXWindowRate6Size (AM RLC relative Tx window size assigned to data rate 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1903
Table 1307 AMRLCRelatTXWindowRate7 (AM RLC relative Tx window size defining
data rate 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1904
Table 1308 AMRLCRelatTXWindowRate7Size (AM RLC relative Tx window size assigned to data rate 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1905
Table 1309 AMRLCRelatTXWindowRate8 (AM RLC relative Tx window size defining
data rate 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1906
Table 1310 AMRLCRelatTXWindowRate8Size (AM RLC relative Tx window size assigned to data rate 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1907
Table 1311 AMRLCRespTimeDCH (AM RLC round trip times with DCH) . . . . . . 1908
Table 1312 AMRLCRespTimeDCH10 (AM RLC round trip time with DCH/DCH of TTI
10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1909
Table 1313 AMRLCRespTimeDCH20 (AM RLC round trip time with DCH/DCH of TTI
20 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1910
Table 1314 AMRLCRespTimeDCH40 (AM RLC round trip time with DCH/DCH of TTI
40 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1911
Table 1315 AMRLCRespTimeDCHRevHSDSCH (AM RLC round trip time for
DCH/HS-DSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1912
Table 1316 AMRLCRespTimeRevEDCH (AM RLC round trip time for E-DCH/DCH) .
1913
Table 1317 AMRLCRespTimeEDCH (AM RLC round trip time with E-DCH) . . . . 1914
Table 1318 AMRLCRespTimeFACHAndRACH (AM RLC round trip time with
FACH/RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1915
108
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1319 AMRLCRespTimeHSDSCH (AM RLC round trip times with HS-DSCH) .
1916
Table 1320 AMRLCRespTimeHSDSCHRevDCH (AM RLC round trip time with HSDSCH/DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1917
Table 1321 AMRLCRespTimeHSDSCHRevEDCH (AM RLC round trip time with HSDSCH/E-DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1918
Table 1322 AMRLCRespTimeHSSRB (AM RLC round trip time for SRBs with HS-RACH/HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1919
Table 1323 AMRLCSRB3n4PeriodMax (AM RLC status period max for SRB3 and
SRB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1920
Table 1324 AMRLCSRB3n4RespTime (AM RLC round trip time for SRB3 and SRB4)
1921
Table 1325 AMRLCSRBHSPA (AM RLC configuration for SRB on HSPA) . . . . 1922
Table 1326 AMRLCRespTimeSRBHSPA (AM RLC round trip time for SRB on HSPA)
1923
Table 1327 AMRLCSRBHSPAMaxDAT (AM RLC MaxDAT transmissions for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1924
Table 1328 AMRLCSRBHSPAPeriodMax (AM RLC status period max for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1925
Table 1329 AMRLCSRBHSPAPeriodMin (AM RLC status period min for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1927
Table 1330 AMRLCSRBHSPAPollPDU (AM RLC period Poll_PDU for SRB on HSPA)
1928
Table 1331 AMRLCSRBHSPAPollSDU (AM RLC period Poll_SDU for SRB on HSPA)
1929
Table 1332 AMRLCSRBHSPAPollWindow (AM RLC period Poll_Window for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1930
Table 1333 AMRLCSRBHSPATriggers (AM RLC status report triggers for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1931
Table 1334 AMRLCTXWindowSizeSRB (AM RLC transmission window sizes for SRBs
2, 3 and 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1933
Table 1335 AMRLCTXWindowSizeSRB2 (AM RLC transmission window size for SRB
2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1934
Table 1336 AMRLCTXWindowSizeSRB3 (AM RLC transmission window size for SRB
3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1935
Table 1337 AMRLCTXWindowSizeSRB4 (AM RLC transmission window size for SRB
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1937
Table 1338 PDUSizeBitRateThr (Bit rate threshold for RLC PDU size 656 with HSDSCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1938
Table 1339 PDUSizeCodeThreshold (Number of HS-PDSCH codes for greater RLC
PDU size) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1939
Table 1340 PDUSizeSIRThr (SIR threshold for RLC PDU size 656 with HS-DSCH) .
1941
Table 1341 RLCConfOptionFPS (RLC Conf option switch for Fast Cell_PCH
Switching) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1942
Table 1342 RNRLCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 1944
Table 1343 RNRLCId (RNRLC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1945
Table 1344 SDUdiscardModeRTPS (SDU discard mode for RT PS RAB employing
RLC AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1946
Table 1345 UMRLCEVoiceDiscardTime (UM RLC SDU discard time in UE for CS voice
over HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1947
DN70456011
Id:0900d80580931b1d
Confidential
109
Radio Network Parameters in Flexi Direct
Table 1346 UMRLCPTTDiscardTime (UM RLC SDU discard time in UE for PTT) . . .
1948
Table 1347 ActivityFactorForAMRDCHTrafficBearers (Activity factor for AMR DCH
traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1950
Table 1348 Af122AMRDL (Activity factor for 12.2 / 12.65 AMR DCH DL bearer) 1951
Table 1349 Af122AMRUL (Activity factor for 12.2 / 12.65 AMR DCH UL bearer) 1951
Table 1350 Af59AMRDL (Activity factor for 5.9 AMR DCH DL bearer) . . . . . . . . 1952
Table 1351 Af59AMRUL (Activity factor for 5.9 AMR DCH UL bearer) . . . . . . . . 1953
Table 1352 ActivityFactorForCSDCHTrafficBearers (Activity factor for CS DCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1954
Table 1353 Af144CSStreDL (Activity factor for 14.4 CS streaming DL bearer) . . 1955
Table 1354 Af144CSStreUL (Activity factor for 14.4 CS streaming UL bearer) . . 1956
Table 1355 Af576CSStreDL (Activity factor for 57.6 CS streaming DL bearer) . . 1957
Table 1356 Af576CSStreUL (Activity factor for 57.6 CS streaming UL bearer) . . 1958
Table 1357 Af64CSConDL (Activity factor for 64 CS conversational DL bearer) . 1959
Table 1358 Af64CSConUL (Activity factor for 64 CS conversational UL bearer) . 1960
Table 1359 ActivityFactorForDCCHTrafficBearers (Activity factor for DCCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1961
Table 1360 Af128And136DCCHDL (Activity factor for 12.8/13.6 DCCH DL bearer) . .
1962
Table 1361 Af128And136DCCHUL (Activity factor for 12.8/13.6 DCCH UL bearer) . .
1963
Table 1362 Af16And17DCCHDL (Activity factor for 1.6/1.7 DCCH DL bearer) . . 1964
Table 1363 Af16And17DCCHUL (Activity factor for 1.6/1.7 DCCH UL bearer) . . 1965
Table 1364 Af32And34DCCHDL (Activity factor for 3.2/3.4 DCCH DL bearer) . . 1966
Table 1365 Af32And34DCCHUL (Activity factor for 3.2/3.4 DCCH UL bearer) . . 1967
Table 1366 ActivityFactorForFACHRACHTrafficBearers (Activity factor for FACH and
RACH traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1968
Table 1367 AfFACHCCDL (Activity factor for FACH-C/C DL bearer) . . . . . . . . . . 1969
Table 1368 AfFACHCIDL (Activity factor for FACH-C/I DL bearer) . . . . . . . . . . . 1970
Table 1369 AfFACHContUL (Activity factor for FACH control UL bearer) . . . . . . 1971
Table 1370 AfFACHSDL (Activity factor for FACH-S DL bearer) . . . . . . . . . . . . . 1972
Table 1371 AfFACHUDL (Activity factor for FACH-U DL bearer) . . . . . . . . . . . . . 1973
Table 1372 AfRACH208UL (Activity factor for RACH 20.8 UL bearer) . . . . . . . . . 1974
Table 1373 AfRACHContDL (Activity factor for RACH control DL bearer) . . . . . . 1975
Table 1374 ActivityFactorForHSPA (Activity factor for HSPA bearers) . . . . . . . . 1976
Table 1375 AfPTTDL (Activity Factor for PTT RAB in Downlink) . . . . . . . . . . . . . 1977
Table 1376 AfPTTUL (Activity Factor for PTT RAB in Uplink) . . . . . . . . . . . . . . . 1978
Table 1377 AfRTHSDPA (Activity factor for RT HSDPA bearer) . . . . . . . . . . . . . 1979
Table 1378 AfRTHSUPA (Activity factor for RT HSUPA bearer) . . . . . . . . . . . . . 1980
Table 1379 AfSRBOnHSDPA (Activity factor for SRB on HSDPA bearer) . . . . . . 1981
Table 1380 AfSRBOnHSUPA (Activity factor for SRB on HSUPA bearer) . . . . . . 1982
Table 1381 ActivityFactorForNRTDCHTrafficBearers (Activity factor for NRT DCH traffic bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1983
Table 1382 Af128NRTDCHDL (Activity factor for 128 NRT DCH DL bearer) . . . . 1985
Table 1383 Af128NRTDCHUL (Activity factor for 128 NRT DCH UL bearer) . . . . 1985
Table 1384 Af16NRTDCHDL (Activity factor for 16 NRT DCH DL bearer) . . . . . . 1986
Table 1385 Af16NRTDCHUL (Activity factor for 16 NRT DCH UL bearer) . . . . . . 1987
110
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1386
Table 1387
Table 1388
Table 1389
Table 1390
Table 1391
Table 1392
Table 1393
Table 1394
Table 1395
Table 1396
Table 1397
Table 1398
Table 1399
Table 1400
Table 1401
Table 1402
Table 1403
Table 1404
Table 1405
Table 1406
Table 1407
Table 1408
Table 1409
Table 1410
Table 1411
Table 1412
Table 1413
Table 1414
Table 1415
Table 1416
Table 1417
Table 1418
Table 1419
Table 1420
Table 1421
Table 1422
Table 1423
Table 1424
Table 1425
Table 1426
Table 1427
Table 1428
Table 1429
Table 1430
DN70456011
Af256NRTDCHDL (Activity factor for 256 NRT DCH DL bearer) . . . 1988
Af256NRTDCHUL (Activity factor for 256 NRT DCH UL bearer) . . . 1989
Af32NRTDCHDL (Activity factor for 32 NRT DCH DL bearer) . . . . . 1990
Af32NRTDCHUL (Activity factor for 32 NRT DCH UL bearer) . . . . . 1991
Af384NRTDCHDL (Activity factor for 384 NRT DCH DL bearer) . . . 1992
Af384NRTDCHUL (Activity factor for 384 NRT DCH UL bearer) . . . 1993
Af64NRTDCHDL (Activity factor for 64 NRT DCH DL bearer) . . . . . 1994
Af64NRTDCHUL (Activity factor for 64 NRT DCH UL bearer) . . . . . 1995
Af8NRTDCHDL (Activity factor for 8 NRT DCH DL bearer) . . . . . . . 1996
Af8NRTDCHUL (Activity factor for 8 NRT DCH UL bearer) . . . . . . . 1997
ActivityFactorForPCHTrafficBearers (Activity factor for PCH traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1998
AfPCHContUL (Activity factor for PCH control UL bearer) . . . . . . . . 1999
AfPCHDL (Activity factor for PCH DL bearer) . . . . . . . . . . . . . . . . . . 2000
ActivityFactorForRTPSTrafficBearers (Activity factor for RT PS traffic
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2001
Af128RTPSAMDL (Activity factor for 128 RT PS AM DL bearer) . . . 2002
Af128RTPSAMUL (Activity factor for 128 RT PS AM UL bearer) . . . 2003
Af128RTPSUMDL (Activity factor for 128 RT PS UM DL bearer) . . . 2004
Af128RTPSUMUL (Activity factor for 128 RT PS UM UL bearer) . . . 2005
Af16RTPSAMDL (Activity factor for 16 RT PS AM DL bearer) . . . . . 2006
Af16RTPSAMUL (Activity factor for 16 RT PS AM UL bearer) . . . . . 2007
Af16RTPSUMDL (Activity factor for 16 RT PS UM DL bearer) . . . . . 2008
Af16RTPSUMUL (Activity factor for 16 RT PS UM UL bearer) . . . . . 2009
Af256RTPSAMDL (Activity factor for 256 RT PS AM DL bearer) . . . 2010
Af256RTPSUMDL (Activity factor for 256 RT PS UM DL bearer) . . . 2011
Af32RTPSAMDL (Activity factor for 32 RT PS AM DL bearer) . . . . . 2012
Af32RTPSAMUL (Activity factor for 32 RT PS AM UL bearer) . . . . . 2013
Af32RTPSUMDL (Activity factor for 32 RT PS UM DL bearer) . . . . . 2014
Af32RTPSUMUL (Activity factor for 32 RT PS UM UL bearer) . . . . . 2015
Af64RTPSAMDL (Activity factor for 64 RT PS AM DL bearer) . . . . . 2016
Af64RTPSAMUL (Activity factor for 64 RT PS AM UL bearer) . . . . . 2017
Af64RTPSUMDL (Activity factor for 64 RT PS UM DL bearer) . . . . . 2018
Af64RTPSUMUL (Activity factor for 64 RT PS UM UL bearer) . . . . . 2019
Af8RTPSAMDL (Activity factor for 8 RT PS AM DL bearer) . . . . . . . 2020
Af8RTPSAMUL (Activity factor for 8 RT PS AM UL bearer) . . . . . . . 2021
Af8RTPSUMDL (Activity factor for 8 RT PS UM DL bearer) . . . . . . . 2022
Af8RTPSUMUL (Activity factor for 8 RT PS UM UL bearer) . . . . . . . 2023
DSCPBTSOMToOMS (DSCP for BTS OM towards OMS) . . . . . . . . 2024
DSCPForGTPSignalling (DSCP for GTP signalling) . . . . . . . . . . . . . 2025
EchoRequestSending (Echo Request Sending) . . . . . . . . . . . . . . . . 2026
IPStackErrorTimer (IP Stack Error timer) . . . . . . . . . . . . . . . . . . . . . 2027
N3Requests (N3-REQUESTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2028
RNTRMChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 2029
RNTRMId (RNTRM Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2030
T3Response (T3-RESPONSE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2031
DediMeasRepPeriodCSdata (Dedicated Measurement Reporting Period
CS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2033
Id:0900d80580931b1d
Confidential
111
Radio Network Parameters in Flexi Direct
Table 1431 DediMeasRepPeriodPSdata (Dedicated Measurement Reporting Period
PS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2034
Table 1432 DedicatedMeasReportPeriod (Dedicated Measurement Reporting Period)
2035
Table 1433 HARQRVConfiguration (HARQ RV Configuration) . . . . . . . . . . . . . . 2036
Table 1434 MeasFiltCoeff (Measurement filter coefficient) . . . . . . . . . . . . . . . . . 2037
Table 1435 NodeBRABReconfigSupport (NodeB PS RAB reconfiguration Support) . .
2038
Table 1436 VBTSChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . . 2039
Table 1437 VBTSId (VBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2041
Table 1438 CSAMRModeSET (Configured CS AMR mode sets) . . . . . . . . . . . . 2042
Table 1439 CSAMRModeSETWB (Configured CS WAMR mode sets) . . . . . . . . 2043
Table 1440 DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . 2045
Table 1441 EDCHMinimumSetETFCI (E-DCH minimum set E-TFCI) . . . . . . . . . 2046
Table 1442 EbNoSetIdentifier (Eb/No parameter set identifier) . . . . . . . . . . . . . . 2046
Table 1443 FastActOfTargetServCell (Faster Activation Of Target Serving Cell) 2047
Table 1444 FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . 2049
Table 1445 HHoMaxAllowedBitrateDL (Maximum allowed DL user bit rate in HHO) . .
2050
Table 1446 HHoMaxAllowedBitrateUL (Maximum allowed UL user bit rate in HHO) . .
2051
Table 1447 HSDPAFmcgIdentifier (HSDPA FMCG identifier) . . . . . . . . . . . . . . . 2052
Table 1448 HSDPAFmciIdentifier (HSDPA FMCI identifier) . . . . . . . . . . . . . . . . . 2053
Table 1449 HSDPAFmcsIdentifier (HSDPA FMCS identifier) . . . . . . . . . . . . . . . 2054
Table 1450 HSDPAHopsIdentifier (HSDPA HOPS identifier) . . . . . . . . . . . . . . . . 2055
Table 1451 HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2056
Table 1452 HSPAFmcsIdentifier (HSPA FMCS identifier) . . . . . . . . . . . . . . . . . . 2057
Table 1453 HSPASCCSpecificATO (HSPA SCC Specific ATO Value) . . . . . . . . 2058
Table 1454 HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay) . 2059
Table 1455 HSUPAEnabled (HSUPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2061
Table 1456 InitialBitRateDL (Initial bit rate in downlink) . . . . . . . . . . . . . . . . . . . . 2062
Table 1457 InitialBitRateUL (Initial bit rate in uplink) . . . . . . . . . . . . . . . . . . . . . . 2063
Table 1458 LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2065
Table 1459 MaxBitRateDLPSNRT (Maximum downlink bit rate for PS domain NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2066
Table 1460 MaxBitRateULPSNRT (Maximum uplink bit rate for PS domain NRT data)
2068
Table 1461 MaxTotalUplinkSymbolRate (Maximum total uplink symbol rate) . . . 2069
Table 1462 MinAllowedBitRateDL (Minimum allowed bit rate in downlink) . . . . . 2071
Table 1463 MinAllowedBitRateUL (Minimum allowed bit rate in uplink) . . . . . . . . 2072
Table 1464 NrtFmcgIdentifier (NRT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . 2074
Table 1465 NrtFmciIdentifier (NRT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2075
Table 1466 NrtFmcsIdentifier (NRT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . 2076
Table 1467 NrtHopgIdentifier (NRT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . 2076
Table 1468 NrtHopiIdentifier (NRT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2077
Table 1469 NrtHopsIdentifier (NRT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . 2078
Table 1470 PowerOffsetUpdMsgSize (Power Offset Update Message Size
Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2079
112
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1471 PtxOffsetHSSCCH (The power offset of the HS-SCCH) . . . . . . . . . 2081
Table 1472 RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2081
Table 1473 RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2083
Table 1474 RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2084
Table 1475 RTwithHSDPAFmciIdentifier (HSDPA FMCI identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2085
Table 1476 RTwithHSDPAFmcsIdentifier (HSDPA FMCS identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2086
Table 1477 RTwithHSDPAHopsIdentifier (HSDPA HOPS identifier for AMR multiservice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2087
Table 1478 RelocComm_in_InterRNC_HHO (Usage of Relocation Commit procedure
in inter RNC HHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2088
Table 1479 RtFmcgIdentifier (RT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2089
Table 1480 RtFmciIdentifier (RT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2089
Table 1481 RtFmcsIdentifier (RT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2090
Table 1482 RtHopgIdentifier (RT HOPG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2091
Table 1483 RtHopiIdentifier (RT HOPI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2092
Table 1484 RtHopsIdentifier (RT HOPS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2093
Table 1485 RxDivIndicator (Rx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . 2094
Table 1486 SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . 2095
Table 1487 SRBHopsIdentifier (SRB HOPS Identifier) . . . . . . . . . . . . . . . . . . . . 2096
Table 1488 VCELChangeOrigin (Change Origin) . . . . . . . . . . . . . . . . . . . . . . . . 2097
Table 1489 VCELId (VCEL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2098
Table 1490 WACSetIdentifier (WAC Parameter Set Identifier) . . . . . . . . . . . . . . 2099
Table 1491 DCHUtilRelAveWin (Window size for the release throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2100
Table 1492 DCHUtilRelThrDL (Threshold for the downlink DCH release
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2101
Table 1493 DCHUtilRelThrUL (Threshold for the uplink DCH release measurement)
2103
Table 1494 DCHUtilRelTimeToTrigger (Time to trigger for the release throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2105
Table 1495 EDCHMACdFlowThroughputAveWin (Window size of E-DCH MAC-d flow
throughput measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2106
Table 1496 EDCHMACdFlowThroughputRelThr (Low throughput threshold of the EDCH MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2107
Table 1497 EDCHMACdFlowThroughputTimetoTrigger (Low throughput time to trigger
of the E-DCH MAC-d flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2108
Table 1498 HSDPAInitialBRULStrNRT (Initial bitrate for HSDPA UL DCH for NRT with
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2109
Table 1499 HSDPAMaxBitrateUL (Maximum bit rate for HSDPA UL DCH return
channel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2110
Table 1500 HSDPAMinBRULStrNRT (Min bitrate for HSDPA UL DCH for NRT with
streaming) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2112
Table 1501 HSDPAinitialBitrateUL (Initial bitrate for HSDPA associated UL DCH) . .
2113
Table 1502 HSDPAminAllowedBitrateUL (Minimum bitrate for HSDPA associated UL
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2114
DN70456011
Id:0900d80580931b1d
Confidential
113
Radio Network Parameters in Flexi Direct
Table 1503 InactCPCBatOptT (Inactive CPC user with battery optimization timer) . . .
2116
Table 1504 InactCPCNoBatOptT (Inactive CPC user without battery optimization
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2119
Table 1505 InactHSRACH (Inactive HS-RACH capable UE) . . . . . . . . . . . . . . . . 2123
Table 1506 InactNonCPCBatOptT (Inactive nonCPC user with battery optimization
timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2125
Table 1507 InactNonCPCNoBatOptT (Inactive nonCPC user without battery optimization timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2128
Table 1508 InactivityTimerDownlinkDCH (Inactivity timer for downlink DCH) . . . 2132
Table 1509 InactivityTimerDownlinkDCH128 (Inactivity timer for downlink 128kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2133
Table 1510 InactivityTimerDownlinkDCH16 (Inactivity timer for downlink 16kbps DCH)
2134
Table 1511 InactivityTimerDownlinkDCH256 (Inactivity timer for downlink 256kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2135
Table 1512 InactivityTimerDownlinkDCH32 (Inactivity timer for downlink 32kbps DCH)
2136
Table 1513 InactivityTimerDownlinkDCH320 (Inactivity timer for downlink 320kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2137
Table 1514 InactivityTimerDownlinkDCH384 (Inactivity timer for downlink 384kbps
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2138
Table 1515 InactivityTimerDownlinkDCH64 (Inactivity timer for downlink 64kbps DCH)
2139
Table 1516 InactivityTimerDownlinkDCH8 (Inactivity timer for downlink 8kbps DCH) .
2140
Table 1517 InactivityTimerUplinkDCH (Inactivity timer for uplink DCH) . . . . . . . . 2141
Table 1518 InactivityTimerUplinkDCH128 (Inactivity timer for uplink 128kbps DCH) . .
2143
Table 1519 InactivityTimerUplinkDCH16 (Inactivity timer for uplink 16kbps DCH) . . . .
2143
Table 1520 InactivityTimerUplinkDCH256 (Inactivity timer for uplink 256kbps DCH) . .
2144
Table 1521 InactivityTimerUplinkDCH32 (Inactivity timer for uplink 32kbps DCH) . . . .
2145
Table 1522 InactivityTimerUplinkDCH320 (Inactivity timer for uplink 320kbps DCH) . .
2146
Table 1523 InactivityTimerUplinkDCH384 (Inactivity timer for uplink 384kbps DCH) . .
2147
Table 1524 InactivityTimerUplinkDCH64 (Inactivity timer for uplink 64kbps DCH) . . . .
2148
Table 1525 InactivityTimerUplinkDCH8 (Inactivity timer for uplink 8kbps DCH) . . 2149
Table 1526 MACdflowthroughputAveWin (Window size of the MAC-d flow throughput
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2150
Table 1527 MACdflowutilRelThr (Low utilisation threshold of the MAC-d flow) . . 2151
Table 1528 MACdflowutilTimetoTrigger (Low utilization time to trigger of the MAC-d
flow) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2152
Table 1529 MSActivitySupervision (Time supervision of user inactivity (for NRT RBs))
2154
Table 1530 PrxNoiseMaxTuneAbsolute (Absolute limit in uplink noise autotuning) . . .
114
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
2155
Table 1531 TrafVolPendingTimeDL (Downlink traffic volume measurement pending
time after trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2156
Table 1532 TrafVolPendingTimeUL (Uplink traffic volume measurement pending time
after trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2158
Table 1533 TrafVolThresholdULLow (Uplink traffic volume measurement low
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2159
Table 1534 UL_DL_activation_timer (UL/DL activation timer) . . . . . . . . . . . . . . . 2161
Table 1535 WACChangeOrigin (WAC Change origin) . . . . . . . . . . . . . . . . . . . . 2162
Table 1536 WACId (WAC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2163
Table 1537 WaitTimeRRC (Wait time in RRC connection request rejection) . . . 2164
Table 1538 WaitTimeRRCbackground (RRC wait time for background causes) 2166
Table 1539 WaitTimeRRCconversational (RRC wait time for conversational causes)
2167
Table 1540 WaitTimeRRCemergency (RRC wait time for emergency causes) 2168
Table 1541 WaitTimeRRChighPrioritySignalling (RRC wait time for high priority signalling causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2169
Table 1542 WaitTimeRRCinterRATreselection (RRC wait time for inter-RAT re-selection causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2170
Table 1543 WaitTimeRRCinteractive (RRC wait time for interactive causes) . . 2171
Table 1544 WaitTimeRRClowPrioritySignalling (RRC wait time for low priority signalling causes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2172
Table 1545 WaitTimeRRCother (RRC wait time for other causes) . . . . . . . . . . . 2173
Table 1546 WaitTimeRRCregistration (RRC wait time for registration causes) 2174
Table 1547 WaitTimeRRCstreaming (RRC wait time for streaming causes) . . 2175
Table 1548 WaitTimeRRCsubscribed (RRC wait time for subscribed causes) . 2176
Table 1549 WaitTimeRRCunknown (RRC wait time for unknown causes) . . . . 2176
Table 1550 AuthorisedNetworkId (Authorised Network Identifier) . . . . . . . . . . . . 2178
Table 1551 AuthorisedNetworkPLMN (Authorised Network PLMN) . . . . . . . . . . 2178
Table 1552 AuthorisedNetworkMCC (Authorised Network Mobile Country Code) 2179
Table 1553 AuthorisedNetworkMNC (Authorised Network Mobile Network Code) . . .
2180
Table 1554 AuthorisedNetworkMNClength (Authorised Network Mobile Network Code
Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2181
Table 1555 Technology (Technology used in the Authorised Network) . . . . . . . 2182
Table 1556 WANEChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 2183
Table 1557 WANEName (WANE Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2184
Table 1558 AdminWBTSState (Admin WBTS State) . . . . . . . . . . . . . . . . . . . . . . 2186
Table 1559 BTSAdditionalInfo (BTS Additional Information) . . . . . . . . . . . . . . . . 2186
Table 1560 BTSIPAddress (BTS O&M IP address) . . . . . . . . . . . . . . . . . . . . . . . 2187
Table 1561 BTSSupportForHSPACM (BTS Support For HSPA CM) . . . . . . . . . 2188
Table 1562 BlindHOIntraBTSQCheck (Blind HO Intra BTS Quality Check) . . . . 2189
Table 1563 BroadcastSIB15 (Broadcast SIB15) . . . . . . . . . . . . . . . . . . . . . . . . . 2190
Table 1564 BroadcastSIB15_2 (Broadcast SIB15.2) . . . . . . . . . . . . . . . . . . . . . . 2192
Table 1565 BroadcastSIB15_3 (Broadcast SIB15.3) . . . . . . . . . . . . . . . . . . . . . . 2193
Table 1566 DCNLinkStatus (O&M DCN link status) . . . . . . . . . . . . . . . . . . . . . . 2194
Table 1567 DCNSecurityStatus (O&M DCN secure link status) . . . . . . . . . . . . . 2194
Table 1568 DLORLAveragingWindowSize (Tx power of radio link averaging window
size for DLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2195
DN70456011
Id:0900d80580931b1d
Confidential
115
Radio Network Parameters in Flexi Direct
Table 1569 DediMeasRepPeriodCSdata (Dedicated Measurement Reporting Period
CS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2197
Table 1570 DediMeasRepPeriodPSdata (Dedicated Measurement Reporting Period
PS data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2198
Table 1571 DedicatedMeasReportPeriod (Dedicated Measurement Reporting Period)
2199
Table 1572 DelayThresholdMax (Maximum Threshold for HSUPA congestion handling
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200
Table 1573 DelayThresholdMax2msTTI (Maximum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2201
Table 1574 DelayThresholdMid (Middle Threshold value for HSUPA congestion
delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2202
Table 1575 DelayThresholdMid2msTTI (Middle Threshold for HSUPA congestion delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2203
Table 1576 DelayThresholdMin (Minimum Threshold value for HSUPA congestion delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2204
Table 1577 DelayThresholdMin2msTTI (Minimum Threshold for HSUPA congestion
delay 2msTTI ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2205
Table 1578 HARQRVConfiguration (HARQ RV Configuration) . . . . . . . . . . . . . . 2206
Table 1579 HSDPA14MbpsPerUser (HSDPA14MbpsPerUser) . . . . . . . . . . . . . . 2207
Table 1580 HSDPACCEnabled (HSDPA Congestion Control activation) . . . . . . 2208
Table 1581 HSUPAXUsersEnabled (HSUPA x users enabled) . . . . . . . . . . . . . . 2209
Table 1582 IPNBId (IPNB object identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2212
Table 1583 InactCACThresholdATM (Inactive users CAC Threshold for ATM) . . 2213
Table 1584 InactCACThresholdIP (Inactive users CAC Threshold for IP) . . . . . . 2214
Table 1585 InactUsersCIDThreshold (Inactive users Connection ID Threshold) . 2215
Table 1586 IntelligentSDPrioHO (Priorized Handover Type in Intelligent Shutdown) .
2216
Table 1587 LoadControlPeriodPS (PS load control period) . . . . . . . . . . . . . . . . . 2217
Table 1588 MaxBTSOMFrameSize (Maximum BTS OM frame size) . . . . . . . . . . 2217
Table 1589 MaxFPDLFrameSizeIub (Maximum FP downlink frame size Iub) . . . 2218
Table 1590 MaxNumberEDCHLCG (Maximum number of E-DCHs in the local cell
group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2220
Table 1591 MeasFiltCoeff (Measurement filter coefficient) . . . . . . . . . . . . . . . . . 2221
Table 1592 MinUDPPortIub (Minimum UDP port value for the Iub) . . . . . . . . . . . 2222
Table 1593 NBAPCommMode (NBAP Communication Mode) . . . . . . . . . . . . . . 2223
Table 1594 NESWVersion (NE-SW-Version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2224
Table 1595 NEType (NE-type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2225
Table 1596 NodeBRABReconfigSupport (NodeB PS RAB reconfiguration Support) . .
2227
Table 1597 PDUSize656WithHSDSCH (Usage of RLC PDU size 656 with HS-DSCH)
2228
Table 1598 PSAveragingWindowSize (Load measurement averaging window size for
packet scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2229
Table 1599 PSRLAveragingWindowSize (Tx power of radio link averaging window size
for PS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2230
Table 1600 PWSMAVTrafficVERLogic (Traffic verification logic in PWSM cell activation process) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2231
Table 1601 PWSMEnableWakeUpTime (Enable cell activation based on time of day)
2233
116
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1602 PWSMInUse (The PWSM usage in BTS) . . . . . . . . . . . . . . . . . . . . . 2234
Table 1603 PWSMRemCellSDBeginHour (PWSM Shutdown Time Begin Hour for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2236
Table 1604 PWSMRemCellSDBeginMin (PWSM Shutdown Time Begin Minute for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2237
Table 1605 PWSMRemCellSDEndHour (PWSM Shutdown Time End Hour for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2238
Table 1606 PWSMRemCellSDEndMin (PWSM Shutdown Time End Minute for remaining cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2239
Table 1607 PWSMShutdownBeginHour (Hour when the cell shutdown window starts)
2240
Table 1608 PWSMShutdownBeginMin (Minute when the cell shutdown window starts)
2241
Table 1609 PWSMShutdownEndHour (Hour when the cell shutdown window ends) .
2242
Table 1610 PWSMShutdownEndMin (Minute when the cell shutdown window ends)
2243
Table 1611 PWSMWeekday (Weekend for shutdown) . . . . . . . . . . . . . . . . . . . . 2244
Table 1612 ProbabilityFactorMax (ProbabilityFactor for Congestion Indication
sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2245
Table 1613 ProbabilityFactorMax2msTTI (ProbabilityFactor for Congestion Indication
sending) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2246
Table 1614 PrxAlpha (Type of measurement filter for uplink total received power) . .
2247
Table 1615 PrxMeasAveWindow (Number of frames to be used averaging in PrxTotal
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2248
Table 1616 PrxTargetPSAdjustPeriod (PS target tune period in HSPA-DCH interference sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2249
Table 1617 PtxAlpha (Type of measurement filter for downlink total transmitted power)
2250
Table 1618 PtxDPCHmax (DPCH downlink transmission power maximum value) . . .
2251
Table 1619 PtxDPCHmin (DPCH downlink transmission power minimum value) 2253
Table 1620 PtxMeasAveWindow (Number of frames to be used averaging in PtxTotal
measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2254
Table 1621 RACHloadIndicationPeriod (RACH load indication period) . . . . . . . . 2255
Table 1622 RFSharingState (RF Sharing State) . . . . . . . . . . . . . . . . . . . . . . . . . 2256
Table 1623 RRIndPeriod (Radio Resource Indication Period) . . . . . . . . . . . . . . 2257
Table 1624 RRMULDCHActivityFactor (Average UL DCH data rates for the radio
bearers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2259
Table 1625 RRMULActivityFactorPTT (Average relative UL data rate for RBs of PTT)
2260
Table 1626 RRMULDCHActivityFactorCSAMR (Average UL DCH data rate for RBs of
CS AMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2261
Table 1627 RRMULDCHActivityFactorCSNTData (Average UL DCH data rate for RB
of CS NT-data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2262
Table 1628 RRMULDCHActivityFactorCSTData (Average UL DCH data rate for RB of
CS T-data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2263
Table 1629 RRMULDCHActivityFactorPSBackgr (Average UL DCH data rate for RB of
PS background RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2264
DN70456011
Id:0900d80580931b1d
Confidential
117
Radio Network Parameters in Flexi Direct
Table 1630 RRMULDCHActivityFactorPSStream (Average UL DCH data rate for RB of
PS Streaming RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2265
Table 1631 RRMULDCHActivityFactorPSTHP1 (Average UL DCH data rate for RB of
PS THP1 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2266
Table 1632 RRMULDCHActivityFactorPSTHP2 (Average UL DCH data rate for RB of
PS THP2 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2266
Table 1633 RRMULDCHActivityFactorPSTHP3 (Average UL DCH data rate for RB of
PS THP3 RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2267
Table 1634 RRMULDCHActivityFactorSRB (Average UL DCH data rate for SRB) . . .
2268
Table 1635 SchedulingPeriod (Scheduling period) . . . . . . . . . . . . . . . . . . . . . . . . 2269
Table 1636 TargetId (Network Element Target Identifier) . . . . . . . . . . . . . . . . . . . 2270
Table 1637 WBTSChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 2271
Table 1638 WBTSId (WBTS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2272
Table 1639 WBTSName (WCDMA BTS name) . . . . . . . . . . . . . . . . . . . . . . . . . . 2273
Table 1640 WBTSSWBuildId (WBTS SW build identifier) . . . . . . . . . . . . . . . . . . 2274
Table 1641 WinACRABsetupDL (DL measurement averaging window for AC) . . 2275
Table 1642 WinACRABsetupUL (UL measurement averaging window for AC) . . 2276
Table 1643 WinLCHSDPA (PtxnonHSPA averaging window size for LC) . . . . . . 2277
Table 1644 WinLCHSUPA (Non E-DCH ST interference averaging window size for
LC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2278
Table 1645 ACBarredList (Access Class Barred list) . . . . . . . . . . . . . . . . . . . . . . 2280
Table 1646 AICHTraTime (AICH Transmission Timing) . . . . . . . . . . . . . . . . . . . . 2281
Table 1647 AMROverSC (AMROverSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2283
Table 1648 AMROverTransmission (AMROverTransmission) . . . . . . . . . . . . . . . 2284
Table 1649 AMROverTxNC (AMROverTxNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2284
Table 1650 AMROverTxNonHSPA (AMROverTxNonHSPA) . . . . . . . . . . . . . . . . 2285
Table 1651 AMROverTxTotal (AMROverTxTotal) . . . . . . . . . . . . . . . . . . . . . . . . 2286
Table 1652 AMRSF (AMRSF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2287
Table 1653 AMRTargetSC (AMRTargetSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2288
Table 1654 AMRTargetTransmission (AMRTargetTransmission) . . . . . . . . . . . . 2289
Table 1655 AMRTargetTxNC (AMRTargetTxNC) . . . . . . . . . . . . . . . . . . . . . . . . 2290
Table 1656 AMRTargetTxNonHSPA (AMRTargetTxNonHSPA) . . . . . . . . . . . . . 2291
Table 1657 AMRTargetTxTotal (AMRTargetTxTotal) . . . . . . . . . . . . . . . . . . . . . . 2292
Table 1658 AMRUnderSC (AMRUnderSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2293
Table 1659 AMRUnderTransmission (AMRUnderTransmission) . . . . . . . . . . . . . 2294
Table 1660 AMRUnderTxNC (AMRUnderTxNC) . . . . . . . . . . . . . . . . . . . . . . . . . 2295
Table 1661 AMRUnderTxNonHSPA (AMRUnderTxNonHSPA) . . . . . . . . . . . . . . 2296
Table 1662 AMRUnderTxTotal (AMRUnderTxTotal) . . . . . . . . . . . . . . . . . . . . . . 2297
Table 1663 ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA) . . 2298
Table 1664 AbsPrioCellReselec (Absolute priority level for cell reselection) . . . . 2300
Table 1665 ActivationTimeOffset (Offset for activation time) . . . . . . . . . . . . . . . . 2301
Table 1666 AdminCellState (Administrative Cell State) . . . . . . . . . . . . . . . . . . . . 2302
Table 1667 AdminPICState (Admin PIC state) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2303
Table 1668 AllowedPreambleSignatures (Allowed preamble signatures) . . . . . . 2304
Table 1669 AllowedRACHSubChannels (Allowed RACH subchannels) . . . . . . . 2306
Table 1670 AltScramblingCodeCM (Compressed Mode: Alternative scrambling code)
2307
118
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1671 AmpliRatioOptHSRACH (HS-RACH amplitude ratio optimized for low/high
bit rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2308
Table 1672 AppAwareRANCapability (Application Aware RAN Capability) . . . . 2309
Table 1673 AppAwareRANEnabled (Application Aware RAN Enabled) . . . . . . . 2310
Table 1674 AssignedPICPool (Cell assigned to PIC pool) . . . . . . . . . . . . . . . . . 2311
Table 1675 AutoACDSACRestriction (Domain Specific Access Class Restriction) . . .
2312
Table 1676 AutoACRPrxTotalAvgWs (Automatic Access Class window size for averaging PrxTotal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2314
Table 1677 AutoACResULOLThr (Automatic Access Class Restriction Uplink Overload Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2315
Table 1678 BlindHOEcNoThrTarget (Blind HO EcNo threshold for target cell) . . 2316
Table 1679 BlindHORSCPThrTarget (Blind HO RSCP threshold for target cell) 2317
Table 1680 CCHSetupEnabled (RRC Connection Setup on CCH Enabled) . . . . 2318
Table 1681 CIRForFDPCH (Carrier to interference ratio for F-DPCH) . . . . . . . . 2319
Table 1682 CId (Cell identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2320
Table 1683 CPCEnabled (CPC enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2321
Table 1684 CPICHEcNoSRBMapRRC (CPICH Ec/No thr for SRB mapping in RRC
setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2323
Table 1685 CPICHRSCPSRBMapRRC (CPICH RSCP thr for SRB mapping in RRC
setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2324
Table 1686 CPICHtoRefRABoffset (Offset of the P-CPICH and reference service
powers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2325
Table 1687 CSAMRModeSET (Configured CS AMR mode sets) . . . . . . . . . . . . 2326
Table 1688 CSAMRModeSETWB (Configured CS WAMR mode sets) . . . . . . . 2328
Table 1689 CSGroupId (Restriction Group Id for Circuit Switched Acces) . . . . . 2329
Table 1690 CTCHCapaHighPri (CTCH capacity for High Priority CBS messages) . .
2330
Table 1691 CUCEcNoThreshold (CPICH Ec/No Threshold Value For CUC Usage) .
2331
Table 1692 CUCRSCPThreshold (CPICH RSCP Threshold Value For CUC Usage) .
2333
Table 1693 CableLoss (Cable Loss) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2334
Table 1694 CellAdditionalInfo (Cell Additional Information) . . . . . . . . . . . . . . . . . 2335
Table 1695 CellBarred (Cell Barred) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2336
Table 1696 CellRange (Cell range) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2337
Table 1697 CellSelQualMeas (Measurement to be used as quality measure) . . 2339
Table 1698 CellWeightForHSDPALayering (Cell weight for HSDPA layering) . . 2340
Table 1699 Cell_Reserved (Cell Reserved for operator use) . . . . . . . . . . . . . . . 2341
Table 1700 CodeTreeOptTimer (Code tree optimisation timer) . . . . . . . . . . . . . . 2343
Table 1701 CodeTreeOptimisation (Code tree optimisation) . . . . . . . . . . . . . . . . 2343
Table 1702 CodeTreeOptimisationGuardTime (Code Tree Optimisation Guard Time)
2344
Table 1703 CodeTreeUsage (Code Tree Usage) . . . . . . . . . . . . . . . . . . . . . . . . 2345
Table 1704 DBandHSDPAEnabled (Dual Band HSDPA Enabled) . . . . . . . . . . . 2346
Table 1705 DCellAndMIMOUsage (DC-HSDPA and MIMO Usage) . . . . . . . . . . 2348
Table 1706 DCellHSDPACapaHO (DC HSDPA Capability HO) . . . . . . . . . . . . . 2349
Table 1707 DCellHSDPAEnabled (DC HSDPA Enabled) . . . . . . . . . . . . . . . . . . 2351
Table 1708 DCellHSDPAFmcsId (DC HSDPA FMCS Identifier) . . . . . . . . . . . . . 2354
DN70456011
Id:0900d80580931b1d
Confidential
119
Radio Network Parameters in Flexi Direct
Table 1709 DLLoadStateTTT (DL loaded state time to trigger) . . . . . . . . . . . . . . 2355
Table 1710 DPCHOverHSPDSCHThreshold (NRT DPCH over HS-PDSCH code
offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2356
Table 1711 DPCModeChangeSupport (DPC Mode Change Support) . . . . . . . . . 2357
Table 1712 DRRCprxMargin (Prx Margin for DRRC) . . . . . . . . . . . . . . . . . . . . . . 2358
Table 1713 DRRCprxOffset (Prx Offset for DRRC) . . . . . . . . . . . . . . . . . . . . . . . 2359
Table 1714 DRRCptxMargin (Ptx Margin for DRRC) . . . . . . . . . . . . . . . . . . . . . . 2360
Table 1715 DRRCptxOffset (Ptx Offset for DRRC) . . . . . . . . . . . . . . . . . . . . . . . 2361
Table 1716 DRXCycleHSFACH (Discontinuous Reception Cycle HS-FACH) . . . 2362
Table 1717 DRXInactiveTimerHSFACH (Inactivity Supervision Timer of HS-FACH for
DRX User ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2363
Table 1718 DRXInterruptHSDSCHData (DRX Interruption by HS-DSCH data) . . 2364
Table 1719 DefMeasCtrlReading (Deferred Measurement Control Reading) . . . 2365
Table 1720 DeltaPrxMaxDown (Maximum uplink power decrease in packet
scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2367
Table 1721 DeltaPrxMaxUp (Maximum uplink power increase in packet scheduling) .
2368
Table 1722 DeltaPtxMaxDown (Maximum downlink power decrease in packet
scheduling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2369
Table 1723 DeltaPtxMaxUp (Maximum downlink power increase in packet scheduling)
2370
Table 1724 DirectSCCEnabled (Direct SCC Enabled) . . . . . . . . . . . . . . . . . . . . . 2371
Table 1725 DirectedRRCEnabled (Directed RRC connection setup enabled) . . . 2372
Table 1726 DirectedRRCForHSDPALayerEnabled (Directed RRC connection setup
for HSDPA layer enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2373
Table 1727 EDCHCapability (E-DCH Capability) . . . . . . . . . . . . . . . . . . . . . . . . . 2374
Table 1728 EDCHMinSetETFCIT0 (E-DCH minimum set E-TFCI 10 ms TTI table 0) .
2375
Table 1729 EDCHMinimumSetETFCI (E-DCH minimum set E-TFCI 10 ms TTI table 1)
2376
Table 1730 EDCHOpState (Operational E-DCH state) . . . . . . . . . . . . . . . . . . . . 2377
Table 1731 EVAMCapability (EVAM capability) . . . . . . . . . . . . . . . . . . . . . . . . . . 2378
Table 1732 EVAMInUse (EVAM in use) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2379
Table 1733 EbNoSetIdentifier (Eb/No parameter set identifier) . . . . . . . . . . . . . . 2380
Table 1734 EvamDInit (Initial phase offset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2381
Table 1735 EvamNumPhaseOffset (Phase offset amount) . . . . . . . . . . . . . . . . . 2382
Table 1736 EvamTKeep (Keep time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2383
Table 1737 EvamTSweep (Sweep time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2384
Table 1738 FDPCHCodeChangeEnabled (F-DPCH code change enabled) . . . . 2385
Table 1739 FDPCHEnabled (F-DPCH enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2386
Table 1740 FDPCHSetup (F-DPCH setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2387
Table 1741 FachLoadMarginCCH (Margin for FACH load for downlink channel type
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2389
Table 1742 FachLoadThresholdCCH (Threshold for FACH load for downlink channel
type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2390
Table 1743 FastActOfTargetServCell (Faster Activation Of Target Serving Cell) 2391
Table 1744 FastCompletionOfSCC (Faster Completion of SCC Procedure) . . . . 2393
Table 1745 FastHSPAMobilityEnabled (Fast HSPA Mobility Enabled) . . . . . . . . 2394
Table 1746 HCS_PRIO (HCS priority level for a cell) . . . . . . . . . . . . . . . . . . . . . . 2396
120
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1747 HHoMaxAllowedBitrateDL (Maximum allowed DL user bit rate in HHO) .
2397
Table 1748 HHoMaxAllowedBitrateUL (Maximum allowed UL user bit rate in HHO) .
2398
Table 1749 HSCapabilityHONumbUE (HSPA Capability Based Handover Max Number of UE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2399
Table 1750 HSCapabilityHOPeriod (HSPA Capability Based Handover Period) 2401
Table 1751 HSDPA64QAMallowed (HSDPA 64 QAM allowed) . . . . . . . . . . . . . 2401
Table 1752 HSDPA64UsersEnabled (HSDPA 64 users enabled) . . . . . . . . . . . . 2403
Table 1753 HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No) 2405
Table 1754 HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No) 2406
Table 1755 HSDPACellChangeMinInterval (Minimum interval between serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2407
Table 1756 HSDPAFmcgIdentifier (HSDPA FMCG identifier) . . . . . . . . . . . . . . . 2409
Table 1757 HSDPAFmciIdentifier (HSDPA FMCI identifier) . . . . . . . . . . . . . . . . 2410
Table 1758 HSDPAFmcsIdentifier (HSDPA FMCS identifier) . . . . . . . . . . . . . . . 2411
Table 1759 HSDPALayeringCommonChEnabled (HSDPA layering for UEs in common
channels enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2412
Table 1760 HSDPAMaxCellChangeRepetition (Max number of repetitive serving HSDSCH cell changes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2413
Table 1761 HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2414
Table 1762 HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2416
Table 1763 HSDPAcapability (HSDPA Capability) . . . . . . . . . . . . . . . . . . . . . . . 2417
Table 1764 HSDPAenabled (HSDPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2418
Table 1765 HSDSCHOpState (Operational HS-DSCH state) . . . . . . . . . . . . . . . 2420
Table 1766 HSFACHActTimeToTrigger (Time to trigger for activity measurement on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2421
Table 1767 HSFACHActivityAveWin (Window size of HS-DSCH MAC-d flow of PS RB
on HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2423
Table 1768 HSFACHActivityThr (Threshold of the HS-DSCH MAC-d flow of PS RB on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2424
Table 1769 HSFACHCapability (High Speed FACH Capability) . . . . . . . . . . . . . 2425
Table 1770 HSFACHDRXEnabled (UE DRX with High Speed Cell FACH Enabled) .
2426
Table 1771 HSFACHEnabled (High Speed Cell_FACH DL Enabled) . . . . . . . . . 2427
Table 1772 HSFACHRABDRAEnabled (HSFACH direct resource allocation for NRT
HSPA RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2428
Table 1773 HSFACHRLCTimeToTrigger (Time to trigger for RLC measurement on
HS-FACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2430
Table 1774 HSFACHRel7ConSetupEC (HSFACH Rel7UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2432
Table 1775 HSFACHRel8ConSetupEC (HSFACH Rel8UE EstCause mapping in RRC
con setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2433
Table 1776 HSFACHVolThrDL (DL traffic volume measurement threshold of HSFACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2435
Table 1777 HSFACHVolThrDLPTT (DL traffic volume measurement threshold of HSFACH for PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2437
Table 1778 HSLoadStateHSDBRLimit (HSPA load state HSDPA bit rate limit) . 2438
DN70456011
Id:0900d80580931b1d
Confidential
121
Radio Network Parameters in Flexi Direct
Table 1779
Table 1780
Table 1781
Table 1782
Table 1783
Table 1784
Table 1785
Table 1786
Table 1787
Table 1788
Table 1789
Table 1790
Table 1791
Table 1792
Table 1793
Table 1794
Table 1795
Table 1796
Table 1797
Table 1798
Table 1799
Table 1800
Table 1801
Table 1802
Table 1803
Table 1804
Table 1805
Table 1806
Table 1807
Table 1808
Table 1809
Table 1810
Table 1811
Table 1812
122
HSLoadStateHSDOffset (HSPA load state HSDPA power Offset) . . 2439
HSLoadStateHSUBRLimit (HSPA load state E-DCH bit rate limit) . . 2440
HSLoadStateHSUOffset (HSPA load state HSUPA power Offset) . . 2441
HSLoadStateHSUResThr (HSPA Load State HSUPA Resource
Threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2442
HSPA128UsersPerCell (HSPA 128 Users per Cell) . . . . . . . . . . . . . 2443
HSPA72UsersPerCell (HSPA 72 Users per Cell) . . . . . . . . . . . . . . . 2445
HSPACapaHO (HSPA Capability Based Handover) . . . . . . . . . . . . . 2447
HSPAFmcsIdentifier (HSPA FMCS identifier) . . . . . . . . . . . . . . . . . . 2449
HSPAQoSEnabled (HSPA QoS enabled) . . . . . . . . . . . . . . . . . . . . . 2450
HSPASCCSpecificATO (HSPA SCC Specific ATO Value) . . . . . . . . 2453
HSPDSCHCodeSet (HS-PDSCH code set) . . . . . . . . . . . . . . . . . . . . 2454
HSPDSCHMarginSF128 (HS-PDSCH code upgrade margin for SF128
codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2456
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay) . 2458
HSRACHActTimeToTrigger (Time to trigger for activity measurement on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2459
HSRACHActivityAveWin (Window size of E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2461
HSRACHActivityThr (Threshold of the E-DCH MAC-d flow of PS RB on
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2462
HSRACHCapability (High Speed RACH Capability) . . . . . . . . . . . . . 2463
HSRACHCommonEDCHRes (Number of Common E-DCH Resources for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2464
HSRACHEnabled (High Speed RACH Enabled) . . . . . . . . . . . . . . . . 2465
HSRACHExtendedAI (Use of Extended Acquisition Indicator HS-RACH) .
2466
HSRACHImplicitRelease (Common E-DCH implicit release for HS-RACH)
2467
HSRACHMPO (HS-RACH Measurement Power Offset) . . . . . . . . . . 2468
HSRACHMaxAllocTimeCCCH (Maximum E-DCH resource alloc time for
CCCH for HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2469
HSRACHMaxPeriodCollis (Max period for collision resolution phase for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2470
HSRACHMaxTotSymbolRate (Maximum total uplink symbol rate of the
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2471
HSRACHSubChannelNumber (Available Sub Channel Number for HSRACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2472
HSRACHTimeToTrigger (Traffic volume measurement time to trigger of
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2474
HSRACHTransmisBackOff (Additional E-DCH transmission back off for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2475
HSRACHVolThrUL (UL traffic volume measurement threshold of HSRACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2476
HSUPA16QAMAllowed (HSUPA 16QAM usage allowed in a cell) . . 2477
HSUPA2MSTTIEnabled (HSUPA 2 ms TTI enabled) . . . . . . . . . . . . 2478
HSUPAEnabled (HSUPA enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . 2480
HSUPAUserLimit16QAM (HSUPA user limit for 16QAM usage) . . . . 2482
HappyBitDelayConHSRACH (Happy bit delay condition for HS-RACH) . .
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1813
Table 1814
Table 1815
Table 1816
Table 1817
Table 1818
Table 1819
Table 1820
Table 1821
Table 1822
Table 1823
Table 1824
Table 1825
Table 1826
Table 1827
Table 1828
Table 1829
Table 1830
Table 1831
Table 1832
Table 1833
Table 1834
Table 1835
Table 1836
Table 1837
Table 1838
Table 1839
Table 1840
Table 1841
Table 1842
Table 1843
DN70456011
2484
HspaMultiNrtRabSupport (HSPA multi NRT RAB Support) . . . . . . . 2485
IncomingLTEISHO (Incoming ISHO from LTE) . . . . . . . . . . . . . . . . 2486
InitialBitRateDL (Initial bit rate in downlink) . . . . . . . . . . . . . . . . . . . . 2487
InitialBitRateUL (Initial bit rate in uplink) . . . . . . . . . . . . . . . . . . . . . . 2488
InterFreqScaleTresel (Scaling factor of Treselection in inter-frequency
case) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2490
InterRATScaleTresel (Scaling factor of Treselection in inter-RAT case) .
2491
IntraFreq_Cell_Reselect_Ind (Intra-frequency cell re-selection indicator)
2492
KforCTCH (CBS frame offset (K)) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2494
LAC (Location area code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2495
LHOCapaReqRejRateDL (Load HO DL NRT capacity request rejection
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2496
LHOCapaReqRejRateUL (Load HO UL NRT capacity request rejection
rate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2497
LHODelayOFFCapaReqRejRate (Delay to broadcast NRT load based HO
state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2499
LHODelayOFFHardBlocking (Delay to broadcast hard blocking load based
HO state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2500
LHODelayOFFInterference (Delay to broadcast interference load based
HO state over) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2501
LHODelayOFFResRateSC (Delay to broadcast DL SC load based HO
state over ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2502
LHOHardBlockingBaseLoad (Load HO hard blocking base load) . . 2503
LHOHardBlockingRatio (Load HO hard blocking ratio) . . . . . . . . . . . 2504
LHOHystTimeCapaReqRejRate (Hysteresis for NRT load measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2505
LHOHystTimeHardBlocking (Hysteresis for hard blocking measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2506
LHOHystTimeInterference (Hysteresis for interference measurement of
LHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2507
LHOHystTimeResRateSC (Hysteresis for DL SC measurement of LHO)
2508
LHONRTTrafficBaseLoad (Load HO NRT traffic base load) . . . . . . 2509
LHONumbUEInterFreq (Number of UEs in inter-frequency load HO ) . . .
2510
LHONumbUEInterRAT (Number of UEs in inter-RAT load HO ) . . . 2511
LHOPwrOffsetDL (Load HO DL power offset) . . . . . . . . . . . . . . . . . 2513
LHOPwrOffsetUL (Load HO UL power offset) . . . . . . . . . . . . . . . . . 2514
LHOResRateSC (Load HO reservation rate of DL spreading codes) 2515
LHOWinSizeOFFCapaReqRejRate (Window size for NRT load measurement to stop LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2517
LHOWinSizeOFFHardBlocking (Window size for hard blocking measurement to stop LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2518
LHOWinSizeOFFInterference (Window size for interference measurement
to stop LHOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2519
LHOWinSizeOFFResRateSC (Window size for DL SC reservation rate
measurement to stop LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2520
Id:0900d80580931b1d
Confidential
123
Radio Network Parameters in Flexi Direct
Table 1844 LHOWinSizeONCapaReqRejRate (Window size for NRT load measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2521
Table 1845 LHOWinSizeONHardBlocking (Window size for hard blocking measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2522
Table 1846 LHOWinSizeONInterference (Window size for interference measurement
to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2523
Table 1847 LHOWinSizeONResRateSC (Window size for DL SC reservation rate
measurement to start LHOs ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2524
Table 1848 LTECellReselection (LTE Cell Reselection) . . . . . . . . . . . . . . . . . . . 2525
Table 1849 LayeringRRCConnRelTargFreq (Target frequency for layering in RRC
Connection Release) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2525
Table 1850 TargetFrequency (Target frequency) . . . . . . . . . . . . . . . . . . . . . . . . . 2526
Table 1851 LayeringRRCRelEnabled (Layering in RRC Connection Release Enabled)
2527
Table 1852 LcrId (Local cell resource identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . 2528
Table 1853 LoadBasedCPICHEcNoSRBHSPA (Load Based CPICH EcNo for SRB on
HSPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2530
Table 1854 LoadBasedCPICHEcNoThreEDCH2MS (Load Based CPICH EcNo
Threshold for E-DCH TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2531
Table 1855 MBLBInactivityEnabled (MBLB in Inactivity Enabled) . . . . . . . . . . . . 2532
Table 1856 MBLBLoadInfoDistr (MBLB Load Information Distribution) . . . . . . . . 2533
Table 1857 MBLBMobilityEnabled (MBLB in Mobility Enabled) . . . . . . . . . . . . . . 2534
Table 1858 MBLBRABSetupEnabled (MBLB in RAB Setup Enabled) . . . . . . . . . 2535
Table 1859 MBLBRABSetupMultiRAB (MBLB in RAB Setup for Multi RAB) . . . . 2536
Table 1860 MBLBStateTransEnabled (MBLB in State Transition Enabled) . . . . . 2537
Table 1861 MEHHSDPAUserNbrCQI (HSDPA CQI user number for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2539
Table 1862 MEHHSUPAUserNbr2msTTI (HSUPA E-DCH 2 ms TTI user number for
the Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2540
Table 1863 MEHLoadStateTtT (Load state time-to-trigger for the Mass Event Handler)
2541
Table 1864 MEHMaxHSUPAUsers (Temporary max number of HSUPA users for the
Mass Event) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2542
Table 1865 MEHQueueThreshold (Scheduling queue threshold for the Mass Event
Handler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2544
Table 1866 MEHULLHSDPAUALimit (UL load based HSDPA user amount limit for the
MEH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2545
Table 1867 MHA (MHA used) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2547
Table 1868 MIMOEnabled (MIMO Enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2549
Table 1869 MIMOHSDPACapaHO (MIMO HSDPA Capability Handover) . . . . . . 2551
Table 1870 MIMOWith64QAMUsage (MIMO with 64QAM usage) . . . . . . . . . . . . 2552
Table 1871 MassEventHandler (Mass Event Handler functions) . . . . . . . . . . . . . 2553
Table 1872 MaxBitRateDLPSNRT (Maximum downlink bit rate for PS domain NRT
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2555
Table 1873 MaxBitRateULPSNRT (Maximum uplink bit rate for PS domain NRT data)
2556
Table 1874 MaxCodeReleases (Max Code Releases) . . . . . . . . . . . . . . . . . . . . . 2558
Table 1875 MaxDLPowerCapability (Maximum DL Power Capability) . . . . . . . . . 2558
Table 1876 MaxIncrInterferenceUL (Max increment in the received wide band
interference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2559
124
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1877 MaxNbrOfHSSCCHCodes (Maximum number of HS-SCCH codes) 2561
Table 1878 MaxNumbHSDPAUsersS (Max number HSDPA users per MAChs/ehs
scheduler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2562
Table 1879 MaxNumbHSDSCHMACdFS (Max number HSDSCH MACd flows per
MAChs/ehs scheduler) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2563
Table 1880 MaxNumberEDCHCell (Maximum number of E-DCHs in the cell) . . 2565
Table 1881 MaxNumberHSDPAUsers (Maximum number of HSDPA users) . . . 2566
Table 1882 MaxNumberHSDSCHMACdFlows (Maximum number of HS-DSCH MACd flows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2568
Table 1883 MaxNumberUECmHO (Maximum number of UEs in CM due to critical HO
measurement ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2569
Table 1884 MaxNumberUECmSLHO (Maximum number of UEs in CM due to SLHO
measurement ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2570
Table 1885 MaxNumberUEHSPACmHO (Max number of UEs in HSDPA CM due to
critical HO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2572
Table 1886 MaxNumberUEHSPACmNCHO (Max number of UEs in HSDPA CM due
to NCHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2573
Table 1887 MaxTotalUplinkSymbolRate (Maximum total uplink symbol rate) . . . 2575
Table 1888 MinAllowedBitRateDL (Minimum allowed bit rate in downlink) . . . . . 2577
Table 1889 MinAllowedBitRateUL (Minimum allowed bit rate in uplink) . . . . . . . 2579
Table 1890 MultiplePLMNListIncluded (Multiple PLMN List Included) . . . . . . . . 2580
Table 1891 N300 (N300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2581
Table 1892 N312 (N312) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2582
Table 1893 N312Conn (N312 for connected mode) . . . . . . . . . . . . . . . . . . . . . . 2584
Table 1894 N313 (N313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2585
Table 1895 N315 (N315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2586
Table 1896 NASsignVolThrDL (Downlink NAS signalling volume threshold) . . . 2588
Table 1897 NASsignVolThrUL (Uplink NAS signalling volume threshold) . . . . . . 2589
Table 1898 NCr (Maximum number of cell reselections) . . . . . . . . . . . . . . . . . . . 2590
Table 1899 NbrOfSCCPCHs (Number of SCCPCHs) . . . . . . . . . . . . . . . . . . . . . 2592
Table 1900 NforCTCH (Period of CTCH allocation (N)) . . . . . . . . . . . . . . . . . . . 2593
Table 1901 NonHCSNcr (Maximum number of cell reselections in non-HCS case) . .
2595
Table 1902 NonHCSTcrMax (Evaluating period for amount of reselections in nonHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2596
Table 1903 NonHCSTcrMaxHyst (Hysteresis to revert from UE measurement in nonHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2597
Table 1904 NrtFmcgIdentifier (NRT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . 2599
Table 1905 NrtFmciIdentifier (NRT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . 2600
Table 1906 NrtFmcsIdentifier (NRT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . 2601
Table 1907 NumberEDCHReservedSHOBranchAdditions (Number of E-DCHs reserved for SHO branch additions) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2602
Table 1908 OCULNRTDCHGrantedMinAllocT (DCH time limit for UL NRT DCH overload in E-DCH cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2603
Table 1909 OCdlNrtDCHgrantedMinAllocT (Threshold for DL NRT DCH allocation time
in enhanced overload control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2605
Table 1910 OffsetToBeginCTCHBSIndex (Offset to Begin CTCH Block Set Index) . .
2606
Table 1911 PBSgrantedMinDCHallocT (PBS granted min DCH allocation time) 2607
DN70456011
Id:0900d80580931b1d
Confidential
125
Radio Network Parameters in Flexi Direct
Table 1912 PBSgrantedMinDCHallocTequalP (PBS granted min DCH allocation time
equal priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2608
Table 1913 PBSgrantedMinDCHallocThigherP (PBS granted min DCH allocation time
higher priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2609
Table 1914 PBSgrantedMinDCHallocTlowerP (PBS granted min DCH allocation time
lower priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2610
Table 1915 PCH24kbpsEnabled (Activate \ Deactivate support for 24kbps PCH) 2611
Table 1916 PFLIdentifier (PFL Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2612
Table 1917 PICState (PIC state) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2613
Table 1918 PI_amount (Number of PI per frame) . . . . . . . . . . . . . . . . . . . . . . . . . 2614
Table 1919 PRACHDelayRange (PRACH Propagation Delay Statistics Cell Range) .
2615
Table 1920 PRACHRequiredReceivedCI (Required received C/I on PRACH at WCDMA BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2616
Table 1921 PRACHScramblingCode (PRACH scrambling code) . . . . . . . . . . . . . 2617
Table 1922 PRACH_preamble_retrans (PRACH Preamble Retrans Max) . . . . . 2618
Table 1923 PSGroupId (Restriction Group Id for Packet Switched Acces) . . . . . 2619
Table 1924 PTxPICH (Transmission power of the PICH channel) . . . . . . . . . . . . 2620
Table 1925 PWSMAVLimitDCHSDPA (Limit for DC HSDPA users in activation) 2622
Table 1926 PWSMAVLimitNRTHSDPA (Limit for NRT HSDPAs for Cell Activation
Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2623
Table 1927 PWSMAVLimitRTDCH (RT DCH power limit for activation) . . . . . . . 2623
Table 1928 PWSMAVLimitRTHSDPA (Limit for RT HSDPAs for Cell Activation
Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2624
Table 1929 PWSMAVPwrNRTHSDPA (NRT HSDPA power per user limit) . . . . 2625
Table 1930 PWSMAVPwrRTHSDPA (RT HSDPA power limit for activation) . . . 2626
Table 1931 PWSMCellGroup (The PWSM cell group of a cell.) . . . . . . . . . . . . . . 2627
Table 1932 PWSMEXPwrLimit (Power limit for virtual AC) . . . . . . . . . . . . . . . . . 2628
Table 1933 PWSMEXUsrLimit (User limit for virtual AC) . . . . . . . . . . . . . . . . . . . 2629
Table 1934 PWSMSDLimitDCHSDPA (Limit for DC HSDPA users in shutdown) 2629
Table 1935 PWSMSDLimitNRTDCH (NRT DCH limit for shutdown) . . . . . . . . . . 2630
Table 1936 PWSMSDLimitNRTHSDPA (Limit for NRT HSDPAs for Cell Shutdown
Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2631
Table 1937 PWSMSDLimitRTDCH (RT DCH limit for shutdown) . . . . . . . . . . . . . 2632
Table 1938 PWSMSDLimitRTHSDPA (Limit for RT HSDPAs for Cell Shutdown
Decision) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2633
Table 1939 PWSMSDPwrNRTHSDPA (NRT HSDPA power per user margin) . . 2634
Table 1940 PWSMSDPwrRTDCH (RT DCH Power limit for shutdown) . . . . . . . . 2635
Table 1941 PWSMSDPwrRTHSDPA (RT HSDPA power limit for shutdown) . . . 2635
Table 1942 PWSMShutdownOrder (The shutdown order of cells in one PWSM cell
group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2636
Table 1943 PWSMShutdownRemCell (Shutdown of a remaining cell) . . . . . . . . 2637
Table 1944 PowerOffsetLastPreamblePRACHmessage (Power offset last preamble
and PRACH message) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2638
Table 1945 PowerOffsetPreamHSRACH (Power Offset Last Transmitted Preamble for
HS-RACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2639
Table 1946 PowerOffsetSCCPCHTFCI (Power offset for S-CCPCH TFCI) . . . . . 2640
Table 1947 PO1_15 (Power offset for SCCPCH TFCI (15 ksps)) . . . . . . . . . . . . 2642
Table 1948 PO1_30 (Power offset for SCCPCH TFCI (30 ksps)) . . . . . . . . . . . . 2643
126
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 1949 PO1_60 (Power offset for SCCPCH TFCI (60 ksps)) . . . . . . . . . . . . 2644
Table 1950 PowerOffsetUpdMsgSize (Power Offset Update Message Size
Optimisation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2645
Table 1951 PowerRampStepPRACHpreamble (Power ramp step on PRACH
preamble) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2647
Table 1952 PowerSaveHSPAType (HSPA Type of Cell in Power Saving Mode) 2647
Table 1953 PriScrCode (Primary downlink scrambling code) . . . . . . . . . . . . . . . 2649
Table 1954 PrxLoadMarginDCH (Interference margin for the minimum UL DCH load)
2650
Table 1955 PrxLoadMarginEDCH (Interference margin for the minimum E-DCH load)
2652
Table 1956 PrxLoadMarginMaxDCH (Interference margin for the maximum UL DCH
load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2653
Table 1957 PrxMaxOrigTargetBTS (Max target received wide band original power for
BTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2654
Table 1958 PrxMaxTargetBTS (Maximum target received wide band power for BTS)
2656
Table 1959 PrxMeasFilterCoeff (Filtering Coefficient of PrxTotal measurement) 2657
Table 1960 PrxNoise (Uplink noise level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2658
Table 1961 PrxNoiseAutotuning (PrxNoise autotuning allowed) . . . . . . . . . . . . . 2659
Table 1962 PrxOffset (Offset for received power) . . . . . . . . . . . . . . . . . . . . . . . . 2660
Table 1963 PrxOffsetWPS (Offset for received Wireless Priority Service power) 2661
Table 1964 PrxTarget (Target for received power) . . . . . . . . . . . . . . . . . . . . . . . 2663
Table 1965 PrxTargetMax (Maximum target for the received total wideband power) .
2664
Table 1966 PrxTargetPSMax (Max PS target in HSPA-DCH interference sharing) . .
2665
Table 1967 PrxTargetPSMaxtHSRACH (Max PS target interference level with HSRACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2666
Table 1968 PrxTargetPSMin (Min PS target in HSPA-DCH interference sharing) 2667
Table 1969 PrxTargetPSStepDown (PS target step down in HSPA-DCH interference
sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2669
Table 1970 PrxTargetPSStepUp (PS target step up in HSPA-DCH interference
sharing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2670
Table 1971 PtxAICH (Transmission power of the AICH channel) . . . . . . . . . . . . 2671
Table 1972 PtxBCCHHSPDSCH (HS-PDSCH Power of HS-FACH for BCCH) . 2672
Table 1973 PtxBCCHHSSCCH (HS-SCCH Power of HS-FACH for BCCH) . . . . 2673
Table 1974 PtxCellMax (Cell maximum transmission power) . . . . . . . . . . . . . . . 2674
Table 1975 PtxDLabsMax (Planned maximum downlink transmission power of a radio
link) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2675
Table 1976 PtxFDPCHMax (F-DPCH maximum transmission power) . . . . . . . . 2676
Table 1977 PtxFDPCHMin (F-DPCH minimum transmission power) . . . . . . . . . 2677
Table 1978 PtxHighHSDPAPwr (High threshold of PtxTotal for dynamic HSDPA pwr
alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2679
Table 1979 PtxMarginCCH (Margin for total downlink transmission power for downlink
channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2680
Table 1980 PtxMaxEHICH (The Maximum transmission power E-HICH) . . . . . . 2680
Table 1981 PtxMaxHSDPA (Maximum allowed HSDPA power) . . . . . . . . . . . . . 2681
Table 1982 PtxMeasFilterCoeff (Filtering Coefficient of PtxTotal measurement) 2683
DN70456011
Id:0900d80580931b1d
Confidential
127
Radio Network Parameters in Flexi Direct
Table 1983
Table 1984
Table 1985
Table 1986
Table 1987
Table 1988
Table 1989
Table 1990
Table 1991
Table 1992
Table 1993
Table 1994
Table 1995
Table 1996
Table 1997
Table 1998
Table 1999
Table 2000
Table 2001
Table 2002
Table 2003
Table 2004
Table 2005
Table 2006
Table 2007
Table 2008
Table 2009
Table 2010
Table 2011
Table 2012
Table 2013
Table 2014
Table 2015
Table 2016
Table 2017
Table 2018
128
PtxOffset (Offset for transmitted power) . . . . . . . . . . . . . . . . . . . . . . 2684
PtxOffsetEAGCH (The transmission power offset of the E-AGCH) . . 2685
PtxOffsetEAGCHDPCCH (The power offset of the E-AGCH) . . . . . . 2686
PtxOffsetEHICHDPCCH (The power offset of the E-HICH) . . . . . . . . 2688
PtxOffsetERGCH (The transmission power offset of the E-RGCH) . . 2689
PtxOffsetERGCHDPCCH (The power offset of the E-RGCH) . . . . . . 2690
PtxOffsetExxCH2ms (The power offset of E-xxCH for 2ms TTI) . . . . 2692
PtxOffsetExxCHSHO (The power offset of E-xxCH for SHO) . . . . . . 2693
PtxOffsetFDPCHSHO (The power offset of F-DPCH for SHO) . . . . . 2694
PtxOffsetHSDPA (Offset for transmitted non-HSDPA power) . . . . . . 2695
PtxOffsetWPS (Offset for transmitted Wireless Priority Service power) . .
2696
PtxPSstreamAbsMax (Maximum transmitted code power of PS streaming
RAB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2697
PtxPrimaryCCPCH (Transmission power of the primary CCPCH channel)
2698
PtxPrimaryCPICH (Transmission power of the primary CPICH channel) .
2700
PtxPrimarySCH (Transmission power of the primary SCH channel) . 2701
PtxSCCPCH1 (Tx power of S-CCPCH for PCH/FACH(s) or standalone
FACH(s)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2703
PtxSCCPCH2 (Tx power of S-CCPCH for Standalone PCH) . . . . . . 2704
PtxSCCPCH2SF128 (Tx power of S-CCPCH for Standalone PCH SF 128)
2706
PtxSCCPCH3 (Tx power of S-CCPCH for SAB) . . . . . . . . . . . . . . . . 2707
PtxSecSCH (Transmission power of the secondary SCH channel) . . 2708
PtxTarget (Target for transmitted power) . . . . . . . . . . . . . . . . . . . . . . 2710
PtxTargetHSDPA (Target for transmitted non-HSDPA power) . . . . . 2711
PtxTargetPSAdjustPeriod (DCH PS target adjust period for dyn HSDPA
pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2712
PtxTargetPSMax (Max DCH PS target for dynamic HSDPA pwr allocation)
2713
PtxTargetPSMaxtHSRACH (Max PS target power level with HS-RACH) .
2715
PtxTargetPSMin (Min DCH PS target for dynamic HSDPA pwr allocation)
2716
PtxTargetPSStepDown (DCH PS target step down for dynamic HSDPA
pwr alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2717
PtxTargetPSStepUp (DCH PS target step up for dynamic HSDPA pwr
alloc) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2718
PtxTargetTotMax (Maximum value for dynamic total tx power) . . . . . 2719
PtxTargetTotMin (Minimum value for dynamic total tx power) . . . . . . 2721
PtxThresholdCCH (Threshold for total downlink transmission power for
downlink channel type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2722
QHCS (Quality threshold level for HCS) . . . . . . . . . . . . . . . . . . . . . . 2723
Qhyst1 (Cell reselection hysteresis 1) . . . . . . . . . . . . . . . . . . . . . . . . 2724
Qhyst1FACH (Cell reselection hysteresis 1 for FACH) . . . . . . . . . . . 2725
Qhyst1PCH (Cell reselection hysteresis 1 for PCH) . . . . . . . . . . . . . 2726
Qhyst2 (Cell reselection hysteresis 2) . . . . . . . . . . . . . . . . . . . . . . . . 2727
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 2019
Table 2020
Table 2021
Table 2022
Table 2023
Table 2024
Table 2025
Table 2026
Table 2027
Table 2028
Table 2029
Table 2030
Table 2031
Table 2032
Table 2033
Table 2034
Table 2035
Table 2036
Table 2037
Table 2038
Table 2039
Table 2040
Table 2041
Table 2042
Table 2043
Table 2044
Table 2045
Table 2046
Table 2047
Table 2048
Table 2049
Table 2050
Table 2051
Table 2052
DN70456011
Qhyst2FACH (Cell reselection hysteresis 2 for FACH) . . . . . . . . . . . 2728
Qhyst2PCH (Cell reselection hysteresis 2 for PCH) . . . . . . . . . . . . . 2729
QqualMin (Minimum required quality level in the cell) . . . . . . . . . . . 2730
QrxlevMin (Minimum required RX level in the cell) . . . . . . . . . . . . . . 2731
RAC (Routing Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2732
RACHCapacity (RACH Capacity) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2734
RACHInterFreqMesQuant (RACH Inter Frequency Measurement
Quantity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2735
RACHIntraFreqMesQuant (RACH Intra Frequency Measurement
Quantity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2736
RACH_Tx_NB01max (RACH random back-off upper bound) . . . . . 2737
RACH_Tx_NB01min (RACH random back-off lower bound) . . . . . . 2739
RACH_tx_Max (RACH maximum number of preamble cycles) . . . . 2740
RACHmeasFilterCoeff (Filtering Coefficient of PRACH measurement) . .
2742
RNARGroupId (Radio Network Access Regulation Function Group Id) . .
2743
RRCconnRepTimer1 (RRC connection setup Retransmission Timer1) . .
2744
RRCconnRepTimer2 (RRC connection setup Retransmission Timer2) . .
2745
RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2747
RTWithHSDPAFmciIdentifier (HSDPA FMCI identifier for speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2748
RTWithHSDPAFmcsIdentifier (HSDPA FMCS identifier for speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2750
RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for speech services)
2751
RXBurstHSFACH (HS-FACH Reception Burst) . . . . . . . . . . . . . . . . 2752
RachLoadMarginCCH (Margin for RACH load for downlink channel type
selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2753
RachLoadThresholdCCH (Threshold for RACH load for downlink channel
type selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2754
RefServForCodePower (Reference service in the max code power
definition) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2755
RelocComm_in_InterRNC_HHO (Usage of Relocation Commit procedure
in inter RNC HHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2757
RsrvdSignaturesOffset (Reserved E-RGCH and E-HICH signatures per
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2758
RtFmcgIdentifier (RT FMCG Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2759
RtFmciIdentifier (RT FMCI Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 2760
RtFmcsIdentifier (RT FMCS Identifier) . . . . . . . . . . . . . . . . . . . . . . . 2761
RxDivIndicator (Rx Diversity Indicator) . . . . . . . . . . . . . . . . . . . . . . . 2762
SABEnabled (Service Area Broadcast Enabled) . . . . . . . . . . . . . . . 2763
SAC (Service Area Code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2764
SACB (Service Area Code for SAB) . . . . . . . . . . . . . . . . . . . . . . . . . 2765
SHCS_RAT (Threshold for inter-RAT measurement rules in HCS) . 2766
SHCS_RATConn (Threshold for inter-RAT measurement for connected
Id:0900d80580931b1d
Confidential
129
Radio Network Parameters in Flexi Direct
Table 2053
Table 2054
Table 2055
Table 2056
Table 2057
Table 2058
Table 2059
Table 2060
Table 2061
Table 2062
Table 2063
Table 2064
Table 2065
Table 2066
Table 2067
Table 2068
Table 2069
Table 2070
Table 2071
Table 2072
Table 2073
Table 2074
Table 2075
Table 2076
Table 2077
Table 2078
Table 2079
Table 2080
Table 2081
Table 2082
Table 2083
Table 2084
Table 2085
Table 2086
Table 2087
Table 2088
Table 2089
Table 2090
Table 2091
Table 2092
Table 2093
130
mode ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2767
SIB11Length (Length of SIB11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2768
SIB11bisLength (Length of SIB11bis) . . . . . . . . . . . . . . . . . . . . . . . . 2769
SIB12Length (Length of SIB12) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2770
SIB4Indicator (Indicator of SIB4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2771
SIB7factor (SIB7 expiration time factor) . . . . . . . . . . . . . . . . . . . . . . . 2771
SIRDPCCHOffsetEDPCH (SIR target offset for DPCCH with E-DPCH) . .
2773
SRBBitRateRRCSetupEC (SRB DCH bit rate in RRC setup based on EC)
2773
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH) . . . 2775
SRBHSPAFmcsId (FMCS identifier for standalone SRB on HSPA) . 2776
SRBMapRRCSetupEC (SRB mapping in RRC setup based on EC) . 2777
SectorID (Sector Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2779
ServHONumbUEInterFreq (Number of inter-frequency service HOs) 2780
ServHONumbUEInterRAT (Number of inter-RAT service HOs) . . . . 2781
ServHOPeriodInterFreq (Period to start inter-frequency service HOs) . . .
2783
ServHOPeriodInterRAT (Period to start inter-RAT service HOs) . . . . 2784
ShutdownStepAmount (Shutdown step amount) . . . . . . . . . . . . . . . . 2785
ShutdownWindow (Shutdown window) . . . . . . . . . . . . . . . . . . . . . . . 2785
Sintersearch (S intersearch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2786
SintersearchConn (S intersearch for connected mode) . . . . . . . . . . . 2787
Sintrasearch (S intrasearch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2789
SintrasearchConn (S intrasearch for connected mode) . . . . . . . . . . . 2790
Slimit_SearchRAT (S limit,SearchRAT) . . . . . . . . . . . . . . . . . . . . . . . 2791
Slimit_SearchRATConn (S limit,SearchRAT for connected mode) . . 2792
SmartLTELayeringEnabled (Smart LTE Layering Enabled) . . . . . . . 2793
SmartLTELayeringRSCP (Smart LTE Layering RSCP threshold) . . . 2795
SmartLTELayeringTSysSel (Smart LTE Layering Target System
Selection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2797
SmartLTELayeringUA (Smart LTE Layering NRT user amount threshold)
2798
SmartTrafVolThrDL (DL traffic volume threshold for Smartphone) . . 2799
SmartTrafVolThrUL (UL traffic volume threshold for Smartphone) . . 2800
SpeedScaleTresel (Scaling factor of Treselection for UE in high mobility)
2802
Sprioritysearch1 (S prioritysearch1) . . . . . . . . . . . . . . . . . . . . . . . . . . 2803
Sprioritysearch2 (S prioritysearch2) . . . . . . . . . . . . . . . . . . . . . . . . . . 2804
SsearchHCS (S searchHCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2806
SsearchHCSConn (S searchHCS for connected mode) . . . . . . . . . . 2807
Ssearch_RAT (S searchRAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2808
Ssearch_RATConn (S searchRAT for connected mode) . . . . . . . . . 2809
T300 (T300) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2810
T312 (T312) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2811
T312Conn (T312 for connected mode) . . . . . . . . . . . . . . . . . . . . . . . 2813
T313 (T313) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2814
T315 (T315) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2815
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 2094
Table 2095
Table 2096
Table 2097
Table 2098
Table 2099
Table 2100
Table 2101
Table 2102
Table 2103
Table 2104
Table 2105
Table 2106
Table 2107
Table 2108
Table 2109
Table 2110
Table 2111
Table 2112
Table 2113
Table 2114
Table 2115
Table 2116
Table 2117
Table 2118
Table 2119
Table 2120
Table 2121
Table 2122
Table 2123
Table 2124
Table 2125
Table 2126
Table 2127
Table 2128
Table 2129
Table 2130
DN70456011
T321 (High Speed Cell FACH DRX operation timer) . . . . . . . . . . . . 2816
TBarred (Cell barred period) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2816
TCrmax (Evaluating period for amount of cell reselections) . . . . . . . 2818
TCrmaxHyst (Hysteresis to revert from UE high-mobility measurements)
2819
TPCCommandERTarget (TPC command error rate target) . . . . . . . 2820
TargetNSEDCHToTotalEDCHPR (Target non-serving E-DCH to total EDCH power ratio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2822
Tcell (Frame timing offset of a cell) . . . . . . . . . . . . . . . . . . . . . . . . . . 2823
Threshservlow (Thresh serving low) . . . . . . . . . . . . . . . . . . . . . . . . 2825
ToAWE_CCH (Time of Arrival Window Endpoint for common channels) .
2827
ToAWS_CCH (Time of Arrival Window Startpoint for common channels)
2828
TrafVolThresholdDLLow (Downlink traffic volume measurement low
threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2829
Treselection (Cell reselection triggering time) . . . . . . . . . . . . . . . . . . 2830
TreselectionFACH (Cell reselection triggering time for FACH) . . . . . 2831
TreselectionPCH (Cell reselection triggering time for PCH) . . . . . . . 2833
UARFCN (UTRA Absolute Radio Frequency Channel Number) . . . 2834
UEDRXCapability (UE DRX in Cell_FACH capability) . . . . . . . . . . . 2837
UEtxPowerMaxDPCH (Maximum UE transmission power on DPCH) 2838
UEtxPowerMaxPRACH (Maximum UE transmission power on PRACH) .
2839
UEtxPowerMaxPRACHConn (Max UE transmission power on PRACH for
connected mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2840
ULLoadStateHSUBRLimit (UL loaded state for HSPAusers bit rate limit)
2841
ULLoadStateHSUOffset (UL loaded state for HSPA users offset) . . 2842
URAId (URA identity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2843
UTRAN_DRX_length (UTRAN DRX cycle length) . . . . . . . . . . . . . . 2844
UseOfHCS (Use of HCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2845
UsersPerHSSCCHCode (Max nbr of conv users per reserved HS-SCCH
code) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2846
VCPMaxHSDPAUsers (Temporary max number of HSDPA users for the
VCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2847
VCPPtxOffset (Voice Call Priority target threshold for HSDPA prevention)
2848
VoiceCallPriority (Voice Call Prioritisation During High Traffic Load) 2850
VoiceOverrideSTHSUPA (Override switch for voice services in the HSUPA
cell) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2851
WACSetIdentifier (WAC Parameter Set Identifier) . . . . . . . . . . . . . . 2852
WCELChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 2853
WCELGlobalCNid (Global CN Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2854
WCELMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . 2855
WCELMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . . 2856
WCELMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . . 2857
WCelState (WCDMA Cell Operational State) . . . . . . . . . . . . . . . . . . 2858
AntBearing (Antenna Bearing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2861
Id:0900d80580931b1d
Confidential
131
Radio Network Parameters in Flexi Direct
Table 2131 AntHPBW (Antenna HPBW (Half Power Beam Width) for Cell) . . . . 2861
Table 2132 AntennaCoord (Antenna Coordinates) . . . . . . . . . . . . . . . . . . . . . . . . 2862
Table 2133 AntennaCoordAltitudeDirect (Antenna Coordinates Altitude Direction) . . .
2864
Table 2134 AntennaCoordAltitudeGround (Antenna Coordinates Altitude of Ground
Level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2865
Table 2135 AntennaCoordLatitudeDegrees (Antenna Coordinates Latitude Degrees)
2866
Table 2136 AntennaCoordLatitudeFractions (Antenna Coordinates Latitude
Fractions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2866
Table 2137 AntennaCoordLatitudeMinutes (Antenna Coordinates Latitude Minutes) .
2867
Table 2138 AntennaCoordLatitudeSeconds (Antenna Coordinates Latitude Seconds)
2868
Table 2139 AntennaCoordLatitudeSign (Antenna Coordinates Latitude Sign) . . . 2869
Table 2140 AntennaCoordLongitudeDegrees (Antenna Coordinates Longitude
Degrees) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2870
Table 2141 AntennaCoordLongitudeFractions (Antenna Coordinates Longitude
Fractions) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2871
Table 2142 AntennaCoordLongitudeMinutes (Antenna Coordinates Longitude
Minutes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2872
Table 2143 AntennaCoordLongitudeSeconds (Antenna Coordinates Longitude
Seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2873
Table 2144 AntennaCoordLongitudeSign (Antenna Coordinates Longitude Sign) . . . .
2873
Table 2145 CovType (Coverage Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2874
Table 2146 EnvCharact (Environment characterisation) . . . . . . . . . . . . . . . . . . . 2875
Table 2147 MaxCellBackRad (Maximum Cell back radius) . . . . . . . . . . . . . . . . . 2876
Table 2148 MaxCellRad (Maximum cell radius) . . . . . . . . . . . . . . . . . . . . . . . . . . 2877
Table 2149 RepeaterExist (Repeater exist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2878
Table 2150 WLCSEChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 2879
Table 2151 WLCSEUtranCellId (LCSE UTRAN Cell Id) . . . . . . . . . . . . . . . . . . . . 2880
Table 2152 WLCSECId (Cell Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2881
Table 2153 WLCSEMCC (Mobile Country Code) . . . . . . . . . . . . . . . . . . . . . . . . . 2882
Table 2154 WLCSEMNC (Mobile Network Code) . . . . . . . . . . . . . . . . . . . . . . . . 2882
Table 2155 WLCSEMNCLength (Mobile Network Code Length) . . . . . . . . . . . . . 2883
Table 2156 WLCSERncId (RNC Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2884
Table 2157 WLCSEid (WLCSE Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2885
Table 2158 DeltaSIR (Delta SIR in the compressed mode) . . . . . . . . . . . . . . . . . 2887
Table 2159 DeltaSIRAfterDownlink (Downlink delta SIR after in the compressed
mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2888
Table 2160 DeltaSIRAfterUplink (Uplink delta SIR after in the compressed mode) . . .
2888
Table 2161 DeltaSIRDownlink (Downlink delta SIR in the compressed mode) . . 2889
Table 2162 DeltaSIRUplink (Uplink delta SIR in the compressed mode) . . . . . . . 2890
Table 2163 DownlinkOrthog (Downlink orthogonality factor) . . . . . . . . . . . . . . . . 2891
Table 2164 EDCHBLERAdjCSVoice10 (HARQ threshold for OLPC of HS CS voice ETTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2892
Table 2165 EDCHBLERAdjCSVoice2 (HARQ threshold for OLPC of HS CS voice E-
132
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2893
Table 2166 EDCHBLERAdjPSConvSpe10 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2895
Table 2167 EDCHBLERAdjPSConvSpe2 (HARQ threshold for OLPC of PS Conv
Speech E-TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2896
Table 2168 EbNoDCHOfPSNRT (Rate matching with the PS NRT DCH) . . . . . 2897
Table 2169 EbNoDCHOfPSNRTPriQua (Primary quality target of the PS NRT DCH)
2899
Table 2170 EbNoDCHOfPSNRTPrim (Primary Eb/N0 of the PS NRT DCH) . . . 2900
Table 2171 EbNoDCHOfPSNRTSec (Secondary Eb/N0 of the PS NRT DCH) . 2901
Table 2172 EbNoDCHOfPSNRTSecQua (Secondary quality target of the PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2903
Table 2173 EbNoDCHOfPSNRTSelQuaDL (Quality target selector for DL PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2904
Table 2174 EbNoDCHOfPSNRTSelQuaUL (Quality target selector for UL PS NRT
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2905
Table 2175 EbNoDCHOfPSStr (Rate matching with the PS streaming DCH) . . . 2907
Table 2176 EbNoDCHOfPSStrPriQua (Primary quality target of the PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2908
Table 2177 EbNoDCHOfPSStrPrim (Primary Eb/N0 of the PS streaming DCH) 2909
Table 2178 EbNoDCHOfPSStrSec (Secondary Eb/N0 of the PS streaming DCH) . . .
2911
Table 2179 EbNoDCHOfPSStrSecQua (Secondary quality target of the PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2912
Table 2180 EbNoDCHOfPSStrSelQuaDL (Quality target selector for DL PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2913
Table 2181 EbNoDCHOfPSStrSelQuaUL (Quality target selector for UL PS streaming
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2915
Table 2182 EbNoDCHOfSRB (Rate matching with the SRB DCH) . . . . . . . . . . . 2916
Table 2183 EbNoDCHOfSRB136 (Planned Eb/N0 of the SRB13.6 DCH) . . . . . 2917
Table 2184 EbNoDCHOfSRB136Qua (Quality target of the SRB13.6 DCH) . . . 2919
Table 2185 EbNoDCHOfSRB34 (Planned Eb/N0 of the SRB3.4 DCH) . . . . . . . 2920
Table 2186 EbNoDCHOfSRB34Qua (Quality target of the SRB3.4 DCH) . . . . . 2921
Table 2187 EbNoDCHRateGain (Data rate gain in the Eb/N0 definition) . . . . . . 2922
Table 2188 EbNoDCHRateGainCSAMR (Data rate gain for the Eb/N0 of the CS AMR)
2924
Table 2189 EbNoDCHRateGainCSData (Data rate gain for the Eb/N0 of the CS data)
2926
Table 2190 EbNoDCHRateGainPSConvSpe (Data rate gain for the Eb/N0 of the PS
conv speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2928
Table 2191 EbNoDCHRateGainPSData (Data rate gain for the Eb/N0 of the PS data
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2930
Table 2192 EbNoDCHRateGainSFDown (Data rate gain selector for the Eb/N0 of the
DL DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2932
Table 2193 EbNoDCHRateGainSFUp (Data rate gain selector for the Eb/N0 of the UL
DCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2933
Table 2194 EbNoDCHRateGainSRB (Data rate gain for the Eb/N0 of the SRB) 2934
Table 2195 EbNoDCHRxDiv2 (Cell offset in the UL Eb/N0, 2-way Rx diversity) . 2936
Table 2196 EbNoDCHRxDiv4 (Cell offset in the UL Eb/N0, 4-way Rx diversity) . 2937
Table 2197 EbNoDCHTxDiv (Cell offset in the DL Eb/N0 definition) . . . . . . . . . . 2938
DN70456011
Id:0900d80580931b1d
Confidential
133
Radio Network Parameters in Flexi Direct
Table 2198 EbNoEDCHCSAMR (Eb/N0 planned for the E-DCH MAC-d flow of CS
voice) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2939
Table 2199 EbNoEDCHOfPSStr (EbNo for E-DCH Streaming) . . . . . . . . . . . . . . 2940
Table 2200 EDCHPSStr128Kbps (EbNo for E-DCH Streaming 128Kbps) . . . . . . 2942
Table 2201 EDCHPSStr16Kbps (EbNo for E-DCH Streaming 16Kbps) . . . . . . . . 2942
Table 2202 EDCHPSStr248Kbps (EbNo for E-DCH Streaming 248Kbps) . . . . . . 2943
Table 2203 EDCHPSStr32Kbps (EbNo for E-DCH Streaming 32Kbps) . . . . . . . . 2944
Table 2204 EDCHPSStr64Kbps (EbNo for E-DCH Streaming 64Kbps) . . . . . . . . 2945
Table 2205 EDCHPSStr8Kbps (EbNo for E-DCH Streaming 8Kbps) . . . . . . . . . . 2946
Table 2206 EDCHPSStrOver248Kbps (EbNo for E-DCH Streaming over 248Kbps) . .
2947
Table 2207 EbNoEDCHPSConvSpeech (Eb/N0 planned for E-DCH PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2948
Table 2208 EbNoOfCSData (Rate matching with the CS data services) . . . . . . . 2949
Table 2209 EbNoDCHOfCSDataNT (Planned Eb/N0 of the CS non transparent data)
2951
Table 2210 EbNoDCHOfCSDataNTQua (Quality target of the CS non transparent
data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2952
Table 2211 EbNoDCHOfCSDataT (Planned Eb/N0 of the CS transparent data) . 2953
Table 2212 EbNoDCHOfCSDataTQua (Quality target of the CS transparent data) . . .
2955
Table 2213 EbNoOfCSNBAMR (Rate matching with the CS NB-AMR) . . . . . . . . 2956
Table 2214 EbNoDCHOfCSNBAMR122 (Planned Eb/N0 of the CS NB-AMR 12.2) . .
2957
Table 2215 EbNoDCHOfCSNBAMR59 (Planned Eb/N0 of the CS NB-AMR 5.9) 2959
Table 2216 EbNoDCHOfCSNBAMRQua (Quality target of the CS NB AMR) . . . 2960
Table 2217 EbNoDCHOfCSNBAMRb (Planned Eb/N0 the CS NB-AMR subflow B) . .
2961
Table 2218 EbNoDCHOfCSNBAMRc (Planned Eb/N0 the CS NB-AMR subflow C) . .
2962
Table 2219 EbNoOfCSWBAMR (Rate matching with the CS WB-AMR) . . . . . . . 2963
Table 2220 EbNoDCHOfCSWBAMR1265 (Planned Eb/N0 of the CS WB-AMR 12.65)
2964
Table 2221 EbNoDCHOfCSWBAMRQua (Quality target of the CS WB-AMR) . . 2966
Table 2222 EbNoDCHOfCSWBAMRb (Planned Eb/N0 the CS WB-AMR subflow B) .
2967
Table 2223 EbNoOfPSConvSpe (Rate matching with the PS conversational speech
services) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2968
Table 2224 EbNoDCHOfPSConvSpe (Planned Eb/N0 of the PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2969
Table 2225 EbNoDCHOfPSConvSpeQua (Quality target of the PS conversational
speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2970
Table 2226 L1BLERTEDCHPSConvSpe10 (BLER target for PS Conversational
speech E-TTI 10 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2971
Table 2227 L1BLERTEDCHPSConvSpe2 (BLER target for PS Conversational speech
E-TTI 2 ms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2973
Table 2228 L1BLERTEDCHVoice10 (BLER target for the HS CS voice E-TTI 10 ms)
2974
Table 2229 L1BLERTEDCHVoice2 (BLER target for the HS CS voice E-TTI 2 ms) . .
2975
134
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Table 2230 SIRDPCCHInitialDCH (Initial SIR target for UL DPCCH with DPDCH) . .
2976
Table 2231 SIRDPCCHInitialDCH128 (UL SIR target without HS-DPCCH - DPDCH SF
128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2978
Table 2232 SIRDPCCHInitialDCH16 (UL SIR target without HS-DPCCH - DPDCH SF
16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2979
Table 2233 SIRDPCCHInitialDCH256 (UL SIR target without HS-DPCCH - DPDCH SF
256) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2980
Table 2234 SIRDPCCHInitialDCH32 (UL SIR target without HS-DPCCH - DPDCH SF
32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2982
Table 2235 SIRDPCCHInitialDCH4 (UL SIR target without HS-DPCCH - DPDCH SF
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2983
Table 2236 SIRDPCCHInitialDCH64 (UL SIR target without HS-DPCCH - DPDCH SF
64) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2984
Table 2237 SIRDPCCHInitialDCH8 (UL SIR target without HS-DPCCH and DPDCH
SF 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2985
Table 2238 SIRDPCCHInitialDCHHS128 (UL SIR target with HS-DPCCH - DPDCH SF
128) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2986
Table 2239 SIRDPCCHInitialDCHHS16 (UL SIR target with HS-DPCCH - DPDCH SF
16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2987
Table 2240 SIRDPCCHInitialDCHHS256 (UL SIR target with HS-DPCCH - DPDCH SF
256) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2988
Table 2241 SIRDPCCHInitialDCHHS32 (UL SIR target with HS-DPCCH - DPDCH SF
32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2989
Table 2242 SIRDPCCHInitialDCHHS4 (UL SIR target with HS-DPCCH - DPDCH SF
4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2990
Table 2243 SIRDPCCHInitialDCHHS64 (UL SIR target with HS-DPCCH - DPDCH SF
64) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2991
Table 2244 SIRDPCCHInitialDCHHS8 (UL SIR target with HS-DPCCH - DPDCH SF
8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2992
Table 2245 SIRDPCCHInitialDCHMax (Maximum SIR target for UL DPCCH with DPDCH only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2993
Table 2246 SIRDPCCHInitialDCHMin (Minimum SIR target for UL DPCCH with DPDCH only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2994
Table 2247 SIRDPCCHInitialDCHOffset (SIR target for UL outerloop power control
with DPDCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2995
Table 2248 SIRDPCCHInitialDCHPSConvSpe (UL SIR target regardless of DL channel - PS conv speech) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2996
Table 2249 SIRDPCCHInitialDCHRxDiv2 (SIR target for UL DPCCH with DPDCH, 2way Rx diversity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2997
Table 2250 SIRDPCCHInitialDCHRxDiv4 (SIR target for UL DPCCH with DPDCH, 4way Rx diversity) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2998
Table 2251 SIRDPCCHInitialEDCH (Initial SIR target for UL DPCCH with E-DCH) . .
3000
Table 2252 SIRDPCCHInitialEDCHPTT10MS (Initial SIR target for UL DPCCH with ETTI 10 ms - PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3001
Table 2253 SIRDPCCHInitialEDCHPTT2MS (Initial SIR target for UL DPCCH with ETTI 2 ms - PTT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3002
Table 2254 WRABChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . 3003
Table 2255 WRABId (WRAB Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3004
Table 2256 GSMRoaming (GSM Roaming allowed) . . . . . . . . . . . . . . . . . . . . . . 3006
DN70456011
Id:0900d80580931b1d
Confidential
135
Radio Network Parameters in Flexi Direct
Table 2257
Table 2258
Table 2259
Table 2260
Table 2261
Table 2262
Table 2263
Table 2264
Table 2265
Table 2266
Table 2267
Table 2268
Table 2269
Table 2270
Table 2271
Table 2272
Table 2273
Table 2274
Table 2275
Table 2276
Table 2277
Table 2278
Table 2279
Table 2280
Table 2281
Table 2282
Table 2283
Table 2284
Table 2285
Table 2286
Table 2287
Table 2288
Table 2289
Table 2290
Table 2291
Table 2292
Table 2293
Table 2294
Table 2295
Table 2296
Table 2297
136
HomePLMN (Subscriber Home PLMN) . . . . . . . . . . . . . . . . . . . . . . . 3006
HomePlmnMCC (Home PLMN Mobile Country Code) . . . . . . . . . . . 3007
HomePlmnMNC (Home PLMN Mobile Network Code) . . . . . . . . . . . 3008
HomePlmnMNCLength (Home PLMN Mobile Network Code Length) . . . .
3009
OperatorName (Name of the subscriber home PLMN) . . . . . . . . . . . 3010
SubscriberGroupId (Subscriber Group Identifier) . . . . . . . . . . . . . . . 3011
WSGAuthorisedNetworkId (Identifier of the Authorised Network) . . . 3011
WSGChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . . . 3012
CiPosCalcInSAS (Cell-ID based Position Calculation in SAS) . . . . . 3014
ConfAreaLevel (Confidence Area Level) . . . . . . . . . . . . . . . . . . . . . . 3015
EmergencyShapeList (Shape Priority List for Emergency Calls) . . . . 3016
EmArc (Arc Priority for Emergency Calls) . . . . . . . . . . . . . . . . . . . . . 3017
EmPoint (Point Priority for Emergency Calls) . . . . . . . . . . . . . . . . . . 3018
EmPointAndAlt (Point And Altitude Priority for Emergency Calls) . . . 3020
EmPointAndCircle (Point And Circle Priority For Emergency Calls) . 3021
EmPointAndEll3D (3D Point And Ellipse Priority For Emergency Calls) . .
3023
EmPointAndEllipse (Point And Ellipse Priority For Emergency Calls) 3024
EmPolygon (Polygon Priority for Emergency Calls) . . . . . . . . . . . . . . 3026
LCSCapacityUsage (LCS Capacity Usage) . . . . . . . . . . . . . . . . . . . . 3028
LCSInterfaceOption (LCS Interface option) . . . . . . . . . . . . . . . . . . . . 3029
LCSShapeConversion (LCS Shape Conversion) . . . . . . . . . . . . . . . 3030
NetworkBasedAGPS (Network based A-GPS) . . . . . . . . . . . . . . . . . 3030
NetworkIndicatorForSAS (Network indicator for SAS) . . . . . . . . . . . . 3031
OperationalMode (SMLC Operational Mode) . . . . . . . . . . . . . . . . . . 3032
PartialAGPSDataDelivery (Partial A-GPS data delivery) . . . . . . . . . . 3033
PeriodicalReportingCapacityUsage (PeriodicalReportingCapacityUsage)
3035
PreferredAGPSMethod (Preferred A-GPS method) . . . . . . . . . . . . . 3035
RNCDelayTolRespTime (Location Reporting Delay Tolerant response
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3037
RNCLowDelayResponseTime (Location Reporting Low Delay Response
time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3038
ShapeList (Shape Priority List for Non-Emergency Calls) . . . . . . . . . 3039
Arc (Arc Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3040
Point (Point Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3041
PointAndAlt (Point And Altitude Priority) . . . . . . . . . . . . . . . . . . . . . . 3043
PointAndCircle (Point And Uncertainty Circle Priority) . . . . . . . . . . . . 3044
PointAndEll3D (3D Point And Ellipse Priority) . . . . . . . . . . . . . . . . . . 3046
PointAndEllipse (Point And Uncertainty Ellipse Priority) . . . . . . . . . . 3047
Polygon (Polygon Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3049
SignallingPointCodeOfSAS (Signalling Point Code of SAS) . . . . . . . 3050
UEBasedAGPS (UE based A-GPS) . . . . . . . . . . . . . . . . . . . . . . . . . 3051
WSMLCChangeOrigin (Change origin) . . . . . . . . . . . . . . . . . . . . . . . 3052
WSMLCid (WSMLC Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3053
Id:0900d80580931b1d
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Summary of changes
Changes between document issues are cumulative. Therefore, the latest document
issue contains all changes made to previous issues.
Changes between issues 05E (RU30, 17-08-2012) and 06 (RU40, 10-09-2013)
Editorial and language corrections to parameter descriptions are not shown.
New Parameters in Issue 06
ADJD
AdjdSRBHopsId (SRB HOPS Identifier)
Description
This parameter identifies the parameter set (HOPS object) which controls the intrafrequency handover to the additional neighbour cell when a user has standalone
SRB allocated on DCH or on HSPA.
If the value of this parameter is "Not defined" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled", the ADJD parameter AdjdRTHopsId
identifies the HOPS parameter set when the standalone SRB is allocated on DCH,
and the ADJD parameter AdjdHSDPAHopsId identifies the HOPS parameter set
when the standalone SRB is allocated on HSPA.
Related features
Soft Handover Based on Detected Set Reporting (optional) AND Fast HSPA
Mobility (optional)
ADJS
SRBHopsIdentifier (SRB HOPS Identifier)
Description
This parameter identifies the parameter set (HOPS object) controlling the intra-frequency handovers of a user having standalone SRB allocated on DCH or on HSPA.
If the value of this parameter is "Not defined" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled", the ADJS parameter RtHopsIdentifier
identifies the HOPS parameter set when the standalone SRB is allocated on DCH,
and the ADJS parameter HSDPAHopsIdentifier identifies the HOPS parameter set
when the standalone SRB is allocated on HSPA.
Related features
Fast HSPA Mobility (optional)
CBCI
ETWSsupportEnabled (ETWS Support Enabled)
Description
This parameter enables/disables ETWS Support feature for the CBC.
DRX cycle length parameters CNDRXLength and UTRAN_DRX_length shall
be less than 4000ms for enabling ETWS support functionality in RNC.
Related features
( Service Area Broadcast (optional) OR SAB Support with 2 SCCPCHs (optional)
) AND 3GPP Rel8 CBS ETWS support (optional)
IUOIdentifier (IUO Object Identifier)
DN70456011
Id:0900d80580a2e11c
Confidential
137
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The IUO identification gives the reference to the IUO object used for the CBCI. The
IUO object contains Iu Operator information.
Related features
Service Area Broadcast (optional) OR SAB Support with 2 SCCPCHs (optional)
IUCS
CNId (Core Network Identity)
Description
This parameter describes the Core Network Identity of the CN connected to the Iu
interface.
CSFlexiIuWeight (CS Flexible Iu Weight)
Description
This parameter defines weight value of each CS CN node (Iu interface) for Flexible
Iu feature load sharing. FlexiIuWeight is used for the weighted round robin method
to select a CN node to balance the load between the available CN nodes. Load
sharing of Iu nodes is defined by configuring FlexiIuWeight of the interface.
The weight value used in load sharing decision is weight value of CN node
divided by sum of all weight values of CN nodes for the domain of one operator.
User divides weights among all CN nodes of the domain/operator for example
like this:
MSS1 60
MSS2 50
MSS3 40
Thus the actual weight value used in load sharing calculation for e.g. MSS1
would be individual weigh value divided by sum of weight values,
60/(60+50+40)=0.4
If the weight value is identical for all CN nodes, it means that the equal load is
shared among all CN nodes. If the weight value is default value (0) for this node, it
means that this node is not used for load sharing.
Related features
Flexible Iu (optional)
IUOIdentifier (IUO Object Identifier)
Description
The IUO identification gives the reference to the IUO object used for the IUCS. The
IUO object contains Iu Operator information
IUO
CSCNDRXLength (CN CS domain specific DRX cycle length)
138
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Description
Summary of changes
The DRX cycle length is used for the CN domain to count paging occasions for discontinuous reception. This parameter is given separately for the CS domain and the
PS domain.
(The duration of the DRX cycle is 2 <power> k frames, where "k" is the used
DRX cycle length coefficient for CN.)
This parameter is part of System Information Block 1.
As per 3GPP the UE may be attached to different CN domains with different
CN domain specific DRX cycle lengths. The UE shall store each CN domain specific
DRX cycle length for each CN domain the UE is attached to and use the shortest of
those DRX cycle lengths.
In-case of MOCN all operators must define the same value of DRX cycle length
and in case of either MORAN (without MOCN at the same time) or MORAN with
Flex IU, DRX cycle length can be operator specific parameter.
PSCNDRXLength (CN PS domain specific DRX cycle length)
Description
The DRX cycle length is used for the CN domain to count paging occasions for discontinuous reception. This parameter is given separately for the CS domain and the
PS domain.
(The duration of the DRX cycle is 2 <power> k frames, where "k" is the used
DRX cycle length coefficient for CN.)
This parameter is part of System Information Block 1.
The UE shall store each CN domain specific DRX cycle length for each CN
domain the UE is attached to and use the shortest of those DRX cycle lengths.
In-case of MOCN all operators must define the same value of DRX cycle length
and in case of either MORAN (without MOCN at the same time) or MORAN with
Flex IU, DRX cycle length can be operator specific parameter.
IuBarringDelayTimerCS (Iu Barring Delay Timer for CS)
Description
This parameter defines the delay that takes place before the Iu link state change is
handled when the Iu-CS (only) service becomes unavailable.
Related features
RNC license control for Iu link break protection (optional)
IuBarringDelayTimerPS (Iu Barring Delay Timer for PS)
Description
This parameter defines the delay that takes place before the Iu link state change is
handled when Iu-PS (only) service becomes unavailable.
Related features
RNC license control for Iu link break protection (optional)
IuBarringRecoveryGroupCS (Iu Barring Recovery Group for CS)
DN70456011
Id:0900d80580a2e11c
Confidential
139
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the amount of cells to which the SIB information is updated
simultaneously after IuCS link recovery. When an IuCS fails, the related CN service
is barred by sending the system information messages to the UEs without the failed
service CN domain. When the failed link is recovered, the system information
messages are sent again with the recovered service CN domain information. The
system information messages are sent simultaneously to the number of cells
defined by the given parameter and sending is phased according to IuBarringRecoveryTimer parameter to avoid the high load of the simultaneous network access
attempts by the UEs.
Related features
RNC license control for Iu link break protection (optional)
IuBarringRecoveryGroupPS (Iu Barring Recovery Group for PS)
Description
The parameter defines the amount of cells to which the SIB information is updated
simultaneously after the IuPS link recovery. When an IuPS fails, the related CN
service is barred by sending the system information messages to the UEs without
the failed service CN domain. When the failed link is recovered, the system information messages are sent again with the recovered service CN domain information.
The system information messages are sent simultaneously to the number of cells
defined by the given parameter and sending is phased according to the IuBarringRecoveryTimer parameter to avoid the high load of the simultaneous network
access attempts by the UEs.
Related features
RNC license control for Iu link break protection (optional)
IuBarringRecoveryTimerCS (Iu service barring recovery timer for CS)
Description
The parameter defines the timer to phase the system information message sending
after IuCS link recovery. When an IuCS link fails, the related CN service is barred
by sending the system information messages to the UEs without the failed service
CN domain. When the failed link is recovered, the system information messages are
sent again with the recovered service CN domain information. The system information sending is phased according to the given parameter to avoid the high load of
the simultaneous network access attempts by the UEs.
Related features
RNC license control for Iu link break protection (optional)
IuBarringRecoveryTimerPS (Iu service barring recovery timer for PS)
Description
The parameter defines the timer to phase the system information message sending
after IuPS link recovery. When an IuPS link fails, the related CN service is barred
by sending the system information messages to the UEs without the failed service
CN domain. When the failed link is recovered, the system information messages are
sent again with the recovered service CN domain information. The system information sending is phased according to the given parameter to avoid the high load of
the simultaneous network access attempts by the UEs.
Related features
RNC license control for Iu link break protection (optional)
PS_NMO (Network Mode of Operation)
140
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Description
Summary of changes
In Operation Mode I, it is possible to have combined CS and PS side paging via
SGSN. In Operation Mode II, the combined paging procedure is not possible (and
neither are combined attach procedures). Used only for the PS domain. NMO is part
of the PS CN domain specific NAS System information in System Information Block
1.
In-case of MOCN all operators must define the same value of NMO and in case
of either MORAN (without MOCN at the same time) or MORAN with Flex IU, NMO
can be operator specific parameter.
CS_T3212 (T3212)
Description
The timeout value, in decihours (6 min), for periodic location updating. Given only
for the CS domain. (Part of the CS domain specific NAS System information in
SIB1).
The value 0 is used for an infinite timeout value, that is, periodic location
updating is not used.
This parameter is part of System Information Block 1.
In-case of MOCN all operators must define the same value of T3212 and in
case of either MORAN (without MOCN at the same time) or MORAN with Flex IU,
T3212 can be operator specific parameter.
IUPS
CNId (Core Network Identity)
Description
This parameter describes the Core Network Identity of the CN connected to the Iu
interface.
IUOIdentifier (IUO Object Identifier)
Description
The IUO identification gives the reference to the IUO object used for the IUPS. The
IUO object contains Iu Operator information.
PSFlexiIuWeight (PS Flexible Iu Weight)
DN70456011
Id:0900d80580a2e11c
Confidential
141
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines weight value of each PS CN node (Iu interface) for Flexible
Iu feature load sharing. FlexiIuWeight is used for the weighted round robin method
to select a CN node to balance the load between the available CN nodes. Load
sharing of Iu nodes is defined by configuring FlexiIuWeight of the interface.
The weight value used in load sharing decision is weight value of CN node
divided by sum of all weight values of CN nodes for the domain of one operator.
User divides weights among all CN nodes of the domain/operator for example
like this:
SGSN1 60
SGSN2 50
SGSN3 40
Thus the actual weight value used in load sharing calculation for e.g. SGSN1
would be individual weigh value divided by sum of weight values,
60/(60+50+40)=0.4
If the weight value is identical for all CN nodes, it means that the equal load is
shared among all CN nodes. If the weight value is default value (0) for this node, it
means that this node is not used for load sharing.
Related features
Flexible Iu (optional)
IUR
AppAwareRANEnabled (Application Aware RAN Enabled)
Description
This parameter defines whether the feature Application Aware RAN is enabled or
not in the corresponding Drift RNC.This parameter value is checked only when the
serving HSDPA/HSPA cell is under Drift RNC.
Dynamic service or application prioritization for the HSDPA scheduling is
applied over Iur towards a corresponding Drift RNC if this parameter value is set to
‘Enabled’.
By enabling this parameter it is interpretive so that all BTSs under the Drift RNC
are supporting RAN2509 feature. This parameter does not have any affect in the
drifting RNC.
Related features
Application Aware RAN (optional)
PFL
PFLDBHSDAMR (Preferred Frequency Layer for DB-DC-HSDPA AMR)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has only an AMR RAB allocated. (CS RABs other than AMR use the same parameter as AMR.)
Child parameters
•
Related features
Multi-Band Load Balancing (optional)
PrefLayerDBHSDAMR
PFLDBHSDAMRNRT (Preferred Frequency Layer for DB-DC-HSDPA AMR and NRT)
142
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has an AMR RAB, 0...1 streaming RAB, and 1...3 NRT RAB(s) allocated. (CS RABs
other than AMR use the same parameter as AMR.)
Child parameters
•
Related features
Multi-Band Load Balancing (optional)
PrefLayerDBHSDAMRNRT
PFLDBHSDNRT (Preferred Frequency Layer for DB-DC-HSDPA NRT)
Description
This parameter defines the preferred layers for DB-DC-HSDPA capable UE that has
only NRT RAB(s) allocated.
Child parameters
•
Related features
Multi-Band Load Balancing (optional)
PrefLayerDBHSDNRT
PFLDBHSDStr (Preferred Frequency Layer for DB-DC-HSDPA Streaming)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has a streaming RAB and 0...3 NRT RAB(s) allocated.
Child parameters
•
Related features
Multi-Band Load Balancing (optional)
PrefLayerDBHSDStr
PFLDBHSDAMR/PrefLayerDBHSDAMR (Preferred Layer for DB-DC-HSDPA AMR)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has only an AMR RAB allocated. (CS RABs other than AMR use the same parameter as AMR.)
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency of the preferred cell. Up to eight different preferred layers
can be defined.
Parent parameter
PFLDBHSDAMR
Related features
Multi-Band Load Balancing (optional)
PFLDBHSDAMRNRT/PrefLayerDBHSDAMRNRT (Preferred Layer for DB-DC-HSDPA
AMR and NRT)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has an AMR RAB, 0...1 streaming RAB, and 1...3 NRT RAB(s) allocated. (CS RABs
other than AMR use the same parameter as AMR.)
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency of the preferred cell. Up to eight different preferred layers
can be defined.
Parent parameter
PFLDBHSDAMRNRT
Related features
Multi-Band Load Balancing (optional)
DN70456011
Id:0900d80580a2e11c
Confidential
143
Summary of changes
Radio Network Parameters in Flexi Direct
PFLDBHSDNRT/PrefLayerDBHSDNRT (Preferred Layer for DB-DC-HSDPA NRT)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has only NRT RAB(s) allocated.
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency of the preferred cell. Up to eight different preferred layers
can be defined.
Parent parameter
PFLDBHSDNRT
Related features
Multi-Band Load Balancing (optional)
PFLDBHSDStr/PrefLayerDBHSDStr (Preferred Layer for DB-DC-HSDPA Streaming)
Description
This parameter defines the preferred layers for Dual Band HSDPA capable UE that
has a streaming RAB and 0...3 NRT RAB(s) allocated.
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency of the preferred cell. Up to eight different preferred layers
can be defined.
Parent parameter
PFLDBHSDStr
Related features
Multi-Band Load Balancing (optional)
RNAC
RNARDSACGuardTime (Access class restriction guard time)
Description
This parameter defines the guard time for the state transitions with RNAR and
DSAC features. If timer is running then the original state transition is done.
If the minimum value is used, timer is not used and state transitions can be
done. This causes extra signalling because UE can activate immediately again.
Related features
Radio Network Access Regulation Function (optional)
RNARDSACCell_DCH (Access class restriction level for Cell_DCH)
Description
This parameter defines the threshold of access class restriction level. If the access
class restriction level goes above the threshold, whenever UE becomes inactive
RNC does not transfer UE to Cell_FACH or Cell/URA_PCH but releases the UE to
the idle if the following is true:
- the last digit of the IMSI of the UE matches the restricted access class and
RNARDSACGuardTimer is not running.
If the minimum parameter value is used, UE's can be moved to IDLE with low
access class restriction level. If the maximum parameter value is used UE can be
moved to IDLE only when the all access classes are restricted.
The functionality is applied in cells as enabled with CMOB-TrafficRestriction.
Related features
Radio Network Access Regulation Function (optional)
RNARDSACCell_PCH (Access class restriction level for Cell_PCH)
144
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the threshold of access class restriction level. If the access
class restriction level goes above the threshold, whenever UE becomes active in
Cell/URA_PCH, RNC does not move UE to Cell_FACH/DCH if the following is true:
- the last digit of the IMSI of the UE matches the restricted access class and
RNARDSACGuardTimer is not running.
If the minimum parameter value is used, UE's is not moved to Cell_FACH/DCH
with low access class restriction level. If the maximum parameter value is used UE
will not be moved to Cell_FACH/DCH when the all access classes are restricted.
The functionality is applied in cells as enabled with CMOB-TrafficRestriction.
Related features
Radio Network Access Regulation Function (optional)
AutoACRestForCellPCH (Access Restriction for Cell_PCH state UE)
Description
This parameter defines the threshold of access class restriction level. If the access
class restriction level goes above the threshold, when ever UE becomes inactive
RNC does not transfer UE to Cell_FACH or Cell/URA_PCH but releases the UE to
the idle if the following is true:
- the last digit of the IMSI of the UE matches the restricted access class in the
current and in the following restriction step
If the minimum parameter value is used UE's will be permitted to do the RRC
connection after the release sooner than if the maximum value is used.
Related features
Automatic access class restriction (optional)
AutoACDecRestHysNRTQ (Automatic Access Class Decrease Restriction Level Hysteresis for NRT queue length trigger)
Description
This parameter defines the time period during which the averaged length of the NRT
scheduling queue must have been continuously lesser than the threshold value to
indicate AC restriction level to be decreased.
Related features
Automatic access class restriction (optional)
AutoACDecRestHysRTWP (Automatic Access Class Decrease Restriction Level Hysteresis for Received Total Wideband Power trigg)
Description
This parameter defines the time period during which the UL load of the cell due to
total received wideband power must have been continuously lesser than the threshold value to indicate AC restriction level to be decreased.
Related features
Automatic access class restriction (optional)
AutoACIncRestHysNRTQ (Automatic Access Class Increase Restriction Level Hysteresis for NRT queue length trigger)
Description
This parameter defines the time period during which the averaged length of the NRT
scheduling queue must have been continuously greater than the threshold value to
indicate AC restriction level to be increased.
Related features
Automatic access class restriction (optional)
DN70456011
Id:0900d80580a2e11c
Confidential
145
Summary of changes
Radio Network Parameters in Flexi Direct
AutoACIncRestHysRTWP (Automatic Access Class Increase Restriction Level Hysteresis for Received Total Wideband Powertrigge)
Description
This parameter defines the time period during which the UL load of the cell due to
total received wide band power must have been continuously greater than the
threshold value to indicate AC restriction level to be increased.
Related features
Automatic access class restriction (optional)
AutoACMaxRestLevel (Automatic Access Class Maximum Restriction Level)
Description
This parameter defines the maximum number of Access Classes (AC0, AC1, ...,
AC9) that are restricted in a cell at the same time.
- 10% indicates that one Access Class is barred in a cell
- 20% indicates that two ACs are barred at the same time
...
- 90% indicates that nine ACs are barred at the same time
Note: All ACs shall not be barred. Maximum restriction level shall be used 90%.
Related features
Automatic access class restriction (optional)
AutoACRLevelUpdInt (Automatic Access Class Restriction Level Update Interval)
Description
The parameter defines the time interval how often the access class restriction level
can updated in System Information broadcast SIB3 during automatic access class
restriction. The trigger for the automatic access class restriction is CN overload,
RNC overload or Cell specific UL overload. If the minimum value is configured, the
automatic access class restriction level is updated frequently. If the maximum value
is configured the automatic access class restriction level is updated very rarely.
Ideally the value of AutoACRLevelUpdInt is half of the value of the RNC-RestrictionInterval.
Related features
Automatic access class restriction (optional)
AutoACRTrigRNCLoad (Automatic Access Class Restriction Trigger of RNC Load)
Description
This parameter defines the threshold for the RNC average unit load to start access
class restriction procedure in Radio Network Controller. The RNC average unit load
is determined by the S-RNTI allocation failure rate in the UE traffic handling units of
the Radio Network Controller. The Trigger starts the automatic access class restriction procedure in all of the cells in Radio Network Controller. The Minimum value
triggers the Automatic Access Class Restriction procedure in a minor RNC overload
situation. The Maximum value starts the Automatic Access Class Restriction procedure only in a very severe RNC overload.
Related features
Automatic access class restriction (optional)
DynHSUPABLERThrBurstyTP (Bursty Data throughput threshold per TTI)
146
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the throughput threshold in number of FP frames per TTI
(10ms). It is used by the outer loop power control of the RNC to check the bursty
data rate condition for Dynamic HSUPA BLER. In case of 2ms TTI, this same
parameter is used with multiple of 5.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DynHSUPABurstyPeriod (Bursty Period for Dyn HSUPA BLER)
Description
This parameter defines minimum period which the BLER state must be bursty
before outer loop power control state can be changed from the bursty BLER state
to continuous BLER state, or from peak or continuous BLER state to bursty BLER
state. It is allowed to change BLER state from bursty or continuous BLER state to
the peak BLER state without waiting for the expiration of the timer set by the parameter DynHSUPABurstyPeriod. Change from peak BLER state to bursty or continuous BLER state is performed if throughput falls below
DynHSUPABLERMaxRateThrB or DynHSUPABLERMaxRateThrC10/
DynHSUPABLERMaxRateThrC2, correspondingly and condition has been valid
time defined with the parameter DynHSUPABurstyPeriod.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
ULFastOLPCDTXthld (DTX threshold for uplink faster outer loop)
Description
This parameter determines the maximum length of the DTX period. During the DTX
period the in-active UL OLPC entity is not allowed to transmit the SIR target modification commands. In case, the controlled bearer has been in DTX for more than
DTX period value and being activated (data available on the Transport Channel),
the UL outer loop PC Entity is allowed to send SIR Target up modification command
to the UL outer loop PC controller.
0 : DTX period value defined as internal constant (200 ms)
1 : DTX period is fixed as zero so that all OLPC entities are always at least
semi-active state and able to send SIR target increase command anytime
The value of this parameter is used, if RNFC-FasterOLPCEnabled parameter
is set to Enabled. Short descriptionThis Parameter determines the maximum
length of the DTX period that does not affect the functionality of the faster UL outer
loop PC.
Related features
Faster OLPC (standard)
FOLPCSIRTgtModInt (Faster OLPC SIR target modification interval)
DN70456011
Id:0900d80580a2e11c
Confidential
147
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the minimum interval between two SIR target modification
commands sent by OLPC entity of UL NRT return channel over the DMPG-DMPG
interface.
The value of this parameter is used, if RNFC-FasterOLPCEnabled parameter
is set to Enabled. Otherwise, RNC internal constant value 500 ms is used.
If the minimum value of parameter is used, OLPC entity sends SIR modification
command more frequently than if the maximum value is used. Short description
This parameter defines the minimum interval between two SIR target modification
commands sent by OLPC entity of UL NRT return channel over the DMPG-DMPG
interface.
Related features
Faster OLPC (standard)
FOLPCStepSizSIRTgt (Faster OLPC step size of SIR target changes)
Description
This Parameter defines the minimum step size of the SIR target modification a PC
Entity of UL NRT return channel can request in case Faster OLPC is enabled.
The value of this parameter is used, if RNFC-FasterOLPCEnabled parameter
is set to Enabled. Otherwise, RNC internal constant value 0.3 dB is used.
If the minimum value of parameter is used, OLPC adjust SIR target more frequently in smaller steps than if the maximum value is used. Short descriptionThis
Parameter defines the minimum step size of the SIR target modification a PC Entity
of UL NRT return channel can request in case Faster OLPC is enabled.
Related features
Faster OLPC (standard)
L1BurstDataBLERTrgtEDCH (Layer1 Bursty Data BLER target for E-DCH)
Description
This parameter defines L1 BLER target for the E-DCH MAC-d flow of PS NRT
service. It is used by the outer loop power control of the RNC for bursty data.
Value of the parameter equals to the log10 of the BLER value.
10^-1 = 0.1 i.e. BLER target is 10%.
Note: BLER target defined by this parameter is used after number of retransmission defined by parameter “Retransmissions in Dyn HSUPA BLER for Bursty
Data”.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
L1ContBLERTrgtEDCH10 (Layer1 Continuous BLER target for E-DCH TTI 10 ms)
148
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines L1 BLER target for the E-DCH MAC-d flow of PS NRT
service when TTI = 10 ms. It is used by the outer loop power control of the RNC for
continuous transmission that provides better throughput and coverage.
Value of the parameter equals to the log10 of the BLER value.
10^-0.7 = 0.199 i.e. BLER target is 20%.
High BLER values increase latency due to HARQ retransmissions in L1, especially this is valid when E-DCH TTI = 10 ms is used.
Note: BLER target defined by this parameter is used after number of retransmission defined by parameter “Retransmissions in Dyn HSUPA BLER for Cont Data
10 ms TTI”.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
L1ContBLERTrgtEDCH2 (Layer1 Continuous BLER target for E-DCH TTI 2 ms)
Description
This parameter defines L1 BLER target for the E-DCH MAC-d flow of PS NRT
service when TTI = 2 ms. It is used by the outer loop power control of the RNC for
continuous transmission that provides better throughput and coverage.
Value of the parameter equals to the log10 of the BLER value.
10^-1 = 0.1 i.e. BLER target is 10%.
High BLER values increase latency due to HARQ retransmissions in L1. When
E-DCH TTI = 2 ms is used latency increase is however small because HARQ period
is 16 ms.
Note: BLER target defined by this parameter is used after number of retransmission defined by parameter “Retransmissions in Dyn HSUPA BLER for Cont Data
2 ms TTI”.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
L1PeakRateBLERTrgtEDCH (Layer1 Peak Data Rate BLER target for E-DCH)
Description
This parameter defines L1 BLER target for the E-DCH MAC-d flow of PS NRT
service. It is used by the outer loop power control of the RNC for peak data rate.
Value of the parameter equals to the log10 of the BLER value.
Examples:
10^-2 = 0.01 i.e. BLER target is 1%.
10^-1.3 = 0.05 i.e. BLER target is 5%.
Note: BLER target defined by this parameter is used after number of retransmission defined by parameter “Retransmissions in Dyn HSUPA BLER for Peak
data”.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
PagingRestrictionInd (Paging Restriction Indication for PPAC)
Description
DN70456011
The parameter defines the paging response restriction per CN domain. Valid when
RNFC - PPACEnabled parameter is enabled.
Id:0900d80580a2e11c
Confidential
149
Summary of changes
Related features
Radio Network Parameters in Flexi Direct
Paging Permission with Access Control (standard)
DynHSUPABLERMaxRateThrC10 (Peak rate thr for cont data of Dyn HSUPA BLER 10
ms TTI )
Description
This parameter defines peak rate threshold in relation to UE max data rate when EDCH TTI = 10 ms. Parameter is used by the dynamic HSUPA BLER algorithm.
Outer loop power control of the RNC applies the parameter when UE is currently
using continuous data. If current throughput exceeds value of the parameter then
OLPC is configured to use the peak data rate configuration.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DynHSUPABLERMaxRateThrC2 (Peak rate thr for cont data of Dyn HSUPA BLER 2 ms
TTI)
Description
This parameter defines peak rate threshold in relation to UE max data rate when EDCH TTI = 2 ms. Parameter is used by the dynamic HSUPA BLER algorithm. Outer
loop power control of the RNC applies the parameter when UE is currently using
continuous data. If current throughput exceeds value of the parameter then OLPC
is configured to use the peak data rate configuration.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DynHSUPABLERMaxRateThrB (Peak rate threshold for bursty data of Dyn HSUPA
BLER)
Description
This parameter defines peak rate threshold in relation to UE max data rate. Parameter is used by the dynamic HSUPA BLER algorithm. Outer loop power control of
the RNC applies the parameter when UE is currently using bursty data. If current
throughput exceeds value of the parameter then OLPC is configured to use the
peak data rate configuration.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
PTTUEMappingARPCap (PTT UE mapping for ARP pre-emption capability)
150
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The parameter defines value of the ARP pre-emption capability that is used to
identify a RAB as PTT RAB. If the value of this parameter does not match with the
related RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
PTTUEMappingARPVul (PTT UE mapping for ARP pre-emption vulnerability)
Description
The parameter defines value of the ARP pre-emption vulnerability that is used to
identify a RAB as PTT RAB. If the value of this parameter does not match with the
related RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
PTTUEMappingARPPrioLevel (PTT UE mapping for ARP priority level)
DN70456011
Id:0900d80580a2e11c
Confidential
151
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter defines value of the ARP priority level that is used to identify a RAB
as PTT RAB. If the value of this parameter does not match with the related RAB
parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
PTTUEMappingARPQue (PTT UE Mapping for ARP queuing allowed)
Description
The parameter defines value of the ARP queuing allowed that is used to identify a
RAB as PTT RAB. If the value of this parameter does not match with the related
RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
PTTUEMappingSignInd (PTT UE mapping for Signaling indication)
152
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The parameter defines value of the Signaling indication that is used to identify a
RAB as PTT RAB. If the value of this parameter does not match with the related
RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
PTTUEMappingTC (PTT UE mapping for Traffic Class)
Description
The parameter defines value of the Traffic Class RAB parameter that is used to
identify a RAB as PTT RAB. If the value of this parameter does not match with the
related RAB parameter value, then that RAB is not identified as PTT RAB.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
PTTUEMappingTHP (PTT UE mapping for Traffic handling priority)
DN70456011
Id:0900d80580a2e11c
Confidential
153
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter defines value of the THP that is used to identify a RAB as PTT RAB.
If the value of this parameter does not match with the related RAB parameter value,
then that RAB is not identified as PTT RAB.
The parameter can also be given value that indicates that this parameter has
no effect to PTT RAB identification. This means that this RAB parameter is ignored
in PTT RAB identification.
The parameter is used only if the PTT feature is activated with the RNFCPTTEnabled parameter.
The parameter is valid only in case of Interactive Traffic Class.
If a RAB is identified as PTT RAB, then the RAB and the user has PTT specific
handling in RAN.
Note: a RAB is identified as PTT RAB if it's RAB parameter values match with
all values set with all the PTTUEMapping parameters:
- PTTUEMappingTC
- PTTUEMappingSignInd
- PTTUEMappingTHP
- PTTUEMappingARPPrioLevel
- PTTUEMappingARPQue
- PTTUEMappingARPVul
- PTTUEMappingARPCap.
Related features
Optimised push to talk experience (optional)
RAU_LAU_RestrictionInd (RAU and LAU Restriction Indication for PPAC)
Description
The parameter defines routing area update, location update and initial direct
transfer restriction per CN domain. Valid when RNFC - PPACEnabled parameter is
enabled.
Related features
Paging Permission with Access Control (standard)
DynHSUPABLERBurstDataRx (Retransmissions in Dyn HSUPA BLER for Bursty Data)
Description
This management parameter defines the L1 HARQ retransmissions threshold for
the outer loop power control entities dedicated to the E-DCH MAC-d flows of the PS
NRT RABs. Its value is used by the outer loop power control of the RNC for the
detection of the block error when the L1 BLER target is defined with the management parameter "Layer1 Bursty Data BLER target for E-DCH". Block error occurs if
the number of the retransmissions equals to or is bigger than the value of the
parameter or an E-HARQ failure has been observed. Outer loop power control
adjusts the uplink DPCCH SIR target after block errors occurs.
Note: Parameter values 2 and 3 will produce high BLER for first transmission.
Also those values will increase SIR target increase interval and thus effective BLER
is even higher.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DynHSUPABLERContDataRx10 (Retransmissions in Dyn HSUPA BLER for Cont Data
10msTTI)
154
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This management parameter defines the L1 HARQ retransmissions threshold for
the outer loop power control entities dedicated to the E-DCH 10 ms TTI MAC-d
flows of the PS NRT RABs. Its value is used by the outer loop power control of the
RNC for the detection of the block error when the L1 BLER target is defined with the
management parameter "Layer1 Continuous BLER target for E-DCH". Block error
occurs if the number of the retransmissions equals to or is bigger than the value of
the parameter or an E-HARQ failure has been observed. Outer loop power control
adjusts the uplink DPCCH SIR target after block errors occurs.
Note: Parameter values 2 and 3 will produce high BLER for first transmission.
Also those values will increase SIR target increase interval and thus effective BLER
is even higher.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DynHSUPABLERContDataRx2 (Retransmissions in Dyn HSUPA BLER for Cont Data 2
ms TTI)
Description
This management parameter defines the L1 HARQ retransmissions threshold for
the outer loop power control entities dedicated to the E-DCH 2 ms TTI MAC-d flows
of the PS NRT RABs. Its value is used by the outer loop power control of the RNC
for the detection of the block error when the L1 BLER target is defined with the management parameter "Layer1 Continuous BLER target for E-DCH". Block error
occurs if the number of the retransmissions equals to or is bigger than the value of
the parameter or an E-HARQ failure has been observed. Outer loop power control
adjusts the uplink DPCCH SIR target after block errors occurs.
Note: Parameter values 2 and 3 will produce high BLER for first transmission.
Also those values will increase SIR target increase interval and thus effective BLER
is even higher.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DynHSUPABLERPeakRateRx (Retransmissions in Dyn HSUPA BLER for Peak data)
Description
This management parameter defines the L1 HARQ retransmissions threshold for
the outer loop power control entities dedicated to the E-DCH MAC-d flows of the PS
NRT RABs. Its value is used by the outer loop power control of the RNC for the
detection of the block error when the L1 BLER target is defined with the management parameter "Layer1 Peak Data Rate BLER target for E-DCH". Block error
occurs if the number of the retransmissions equals to or is bigger than the value of
the parameter or an E-HARQ failure has been observed. Outer loop power control
adjusts the uplink DPCCH SIR target after block errors occurs.
Note: Parameter values 2 and 3 will produce high BLER for first transmission.
Also those values will increase SIR target increase interval and thus effective BLER
is even higher.
Related features
DN70456011
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
Id:0900d80580a2e11c
Confidential
155
Summary of changes
Radio Network Parameters in Flexi Direct
RRCConnSetupMsgSize (RRC Connection Setup Message Size Optimisation)
Description
This parameter indicates whether the RRC CONNECTION SETUP message size
optimisation functionality is enabled.
When enabled, this functionality introduces message size optimisation for RRC:
RRC CONNECTION SETUP message, which is achieved by sending Complete
Configuration (CC) with single Cell_DCH mapping. Because Cell_FACH mapping
is removed, RRC Connection Setup message size is reduced from 2 to 1 TB (Transport Block) resulting faster and more reliable signaling.
Other option for optimising RRC Connection Setup message is to use Default
Configuration (DC).
If either of above option is activated, RACH/FACH RB mapping information for
SRBs is provided after RRC connection setup procedure during the first Radio
Bearer Setup procedure, but with a separate Radio Bearer Reconfiguration procedure.
The RRC CONNECTION SETUP message size is not optimised if either the
value of this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
The complete parameter value descriptions are the following: 0 (Disabled), 1
(Default Configuration for rel6 and newer UEs and Complete Configuration with
dual mapping for rel5 and older UEs), 2 (Complete Configuration for rel5 and older
UEs with single mapping and Complete Configuration with dual mapping for rel6
and newer UEs), 3 (Default Configuration for rel6 and newer UEs and Complete
Configuration with single mapping for rel5 and older UEs), 4 (Complete Configuration for rel6 and newer UEs with single mapping and Complete Configuration with
dual mapping for rel5 and older UEs), 6 (Complete Configuration for all UEs with
single mapping)
Related features
Fast HSPA Mobility (optional)
DynHSUPABLERAlgTrgTime (Time to trigger Dyn HSUPA BLER Algorithm)
Description
This parameter indicates the number of TTIs (10ms) after that Dynamic HSUPA
BLER Algorithm shall be triggered by outer loop power control in the RNC. This is
time to trigger type parameter. In case of 2ms TTI, this same parameter is used with
multiple of 5.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
DynHSUPABLERFrameWinSiz (Window size for FP Frames Measurement)
Description
This parameter defines the size of the sliding averaging window for FP frames measurement of the E-DCH FP. The measurement measures the number of FP frames
transmitted by the E-DCH FP during the sliding measurement window. The value 0
of the parameter means that the E-DCH FP frames measurement is not performed.
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
RNC
AlarmSetforWCELBLINIT (Alarm Set for WCEL BL-INIT)
156
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Description
Summary of changes
This parameter is used to enable or disable the alarm setting for WCEL objects that
stay in BL-INIT state for excessive time.
Notes: activation (alarms get set after certain time for BL-INIT WCELs) and
deactivation (alarms are not set for BL-INIT WCELs, alarms set prior to deactivation
will stay active).
CSAttachDetachAllowed (Attach-detach allowed)
Description
This parameter determines whether or not IMSI attach and detach are allowed.
0 = MSs should not apply the IMSI attach and detach procedure,
1 = MSs should apply the IMSI attach and detach procedure.
This parameter is given only for the CS domain. (Part of the CS domain specific
NAS System information in SIB1.)
This parameter is part of System Information Block 1.
DSCPStatisticsGroupTCPack (DSCP code for DL TCP Ack statistics)
Description
This parameter defines which Iu-PS GTP user plane data DSCP code is mapped to
counter M1022Cxx DL TCP ACKs. This parameter defines the value of a DSCP
code that the operator sets for DL TCP ACKs for a specific UL data. This DSCP
value will be mapped to one of the six application groups configured by operator.
This parameter is used to update cell level counter to track number of incoming
DL TCP ACK packets with this specific DSCP marking.
Related features
Application Aware RAN (optional)
DSCPStatisticsGroupA (DSCP statistics group A )
Description
This parameter defines which Iu-PS GTP user plane data DSCP code is mapped to
counter M1022Cxx IUPS DSCP CLASS A. This parameter defines the value of a
DSCP level that the operator chooses to monitor in a cell.
This parameter is used to update cell level counter to track number of incoming
DL packets with DSCP marking A.
Related features
Application Aware RAN (optional)
DSCPStatisticsGroupB (DSCP statistics group B)
Description
This parameter defines which Iu-PS GTP user plane data DSCP code is mapped to
counter M1022Cxx IUPS DSCP CLASS B. This parameter defines the value of a
DSCP level that the operator chooses to monitor in a cell.
This parameter is used to update cell level counter to track number of incoming
DL packets with DSCP marking B.
Related features
Application Aware RAN (optional)
DSCPStatisticsGroupC (DSCP statistics group C)
DN70456011
Id:0900d80580a2e11c
Confidential
157
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines which Iu-PS GTP user plane data DSCP code is mapped to
counter M1022Cxx IUPS DSCP CLASS C. This parameter defines the value of a
DSCP level that the operator chooses to monitor in a cell.
This parameter is used to update cell level counter to track number of incoming
DL packets with DSCP marking C.
Related features
Application Aware RAN (optional)
MACLogicalChPriority (MAC logical channel priority definition)
Description
This parameter defines MAC logical channel priority for Signalling Radio Bearers
SRB1, SRB2 and SRB3.
The MAC logical channel priority for SRB1, SRB2 and SRB3 can be defined
based on domain and Traffic Class (TC) .
These priorities are values in the range of 1 - 3. (1 is the highest and 3 is the
lowest priority).
For example, see the following prioritization orders:
Priority Default Config#1
1 SRBs (1-3) SRB 1
2 SRB 2
3 SRB 3
Child parameters
•
•
•
Related features
Fast Cell_PCH Switching (optional)
MACLogChPriSRB1
MACLogChPriSRB2
MACLogChPriSRB3
MACLogicalChPriority/MACLogChPriSRB1 (MAC logical channel priority for SRB1)
Description
This parameter defines MAC logical channel priority for Signalling Radio Bearer1
Parent parameter
MACLogicalChPriority
Related features
Fast Cell_PCH Switching (optional)
MACLogicalChPriority/MACLogChPriSRB2 (MAC logical channel priority for SRB2)
Description
This parameter defines MAC logical channel priority for Signalling Radio Bearer2
Parent parameter
MACLogicalChPriority
Related features
Fast Cell_PCH Switching (optional)
MACLogicalChPriority/MACLogChPriSRB3 (MAC logical channel priority for SRB3)
Description
This parameter defines MAC logical channel priority for Signalling Radio Bearer3
Parent parameter
MACLogicalChPriority
Related features
Fast Cell_PCH Switching (optional)
RncClientTLSMode (RNC Client TLS Mode)
158
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Description
Summary of changes
Parameter defines the BTS O&M client connection mode which RNC uses when
connecting to OMS.
Off = Only insecure connection establishment is allowed
Probing = Both secure and insecure connection establishments are allowed
Forced = Only secure connection establishment is allowed
Parameter defines the RNC TLS Mode parameter value for the BTS O&M client,
which is used in start-up to determine the correct security operational mode of the
BTS O&M connection establishment towards OMS. Parameter can be configured
locally in RNC.
RNCIPAddress (RNC IP-address)
Description
This parameter specifies the RNC IP address that is needed to establish TCP/IP
connections to the RNC OMU.
Related features
New WBTS Parameters in Topology Data for Flexi/Ultra/MetroSite BTSs (standard)
CBCSourceIPAddress (Source IP address for IuBC interface)
Description
Source IP address used for SABP application towards one CBC. Same address can
be used for max 4 CBCs.
Examples:
IPv4, 255.255.255.255, 1.1.1.1
Related features
Source IP on ICSU used for IuBC interface (standard) AND Service Area Broadcast (optional)
WCELIdleAlarmTimeout (WCEL Idle Alarm Timeout)
Description
This parameter determines time interval after which WCELs staying in BL-INIT state
are informed to the user via alarms.
RNFC
AutoACResEnabled (Automatic Access Class Restriction Enabled)
DN70456011
Id:0900d80580a2e11c
Confidential
159
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter enables/disables the use of Automatic Access Class restriction in
the RNC for different overload triggers. Activation and deactivation can be done
separately for different overload triggers.
‘Automatic Access Class Restriction’ uses a binary notation of 4 bits where:
- bit 0 indicates whether or not the feature is activated for the Total Received
wideband power
- bit 1 indicates whether or not the feature is activated for NRT scheduling queue
length
- bit 2 indicates whether or not the feature is activated for the CN overload
- bit 3 indicates whether or not the feature is activated for the RNC overload
If a bit is set to 1, the feature is activated for the corresponding overload trigger.
If a bit is set to 0, the feature is not activated for the corresponding overload trigger
e.g. If a bit0 is set to 1 then Total Received wideband power trigger is activated. If
a bit0 is set to 0 then Total Received wideband power trigger is de-activated.
Active triggers can restricted the number of UE Access Classes using SIB
messages in case overload is detected due to those triggers. Restricted access
classes cannot access radio network.
Automatic Access Class restriction feature is enabled, if at least one bit (bit0,
bit1, bit2, bit3) is set to 1.
Note: Parameters of mass event handler must be configured if NRT queue
length functionality is activated (bit1 is set to 1).
Related features
Automatic access class restriction (optional)
CSFBEnabled (CSFB Enabled)
Description
The parameter indicates whether CS Fallback (RAN2435) functionality is enabled
in the RNC or not.
CSFB functionality is activated in the cell only if both parameters CSFBEnabled
(for RNC) and IncomingLTEISHO (for cell) are in state Enabled. RAN 2435 SRVCC
from LTE and CCSFB with HO feature needs license RAN2067 LTE InterworkingISHO from LTE
Related features
SRVCC from LTE and CSFB with HO (optional)
DCH00SuppOnIurEnabled (DCH 0/0 Support On Iur Enabled)
Description
This parameter defines whether the AMR with DCH 0/0 Support on Iur feature is
enabled in the RNC. When enabled in the RNC, this feature introduces DRNC
support for establishing DCH 0/0 PS RB on Iur.
The feature is out of use in the RNC if either the state of the license is "Off/Config", or the value of this parameter is set to 'Disabled'.
Related features
AMR with DCH (0,0) Support on Iur (optional)
DCHtoPCHEnabled (Enabling direct Cell_DCH to PCH state transition)
Description
This parameter defines whether direct transition from Cell_DCH to Cell_PCH is
allowed or not.
FastPCHSwitchEnabled (Enabling Fast Cell_PCH Switching feature)
160
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter enables/disables the RAN2494 (Fast Cell_PCH Switching) feature.
Fast Cell PCH Switching feature attempts to make faster transition from
Cell/URA_PCH / Cell_FACH to Cell_DCH.
Related features
Fast Cell_PCH Switching (optional)
FasterOLPCEnabled (Faster OLPC Enabled)
Description
This parameter determines the Activation/Deactivation of Faster Outer Loop Power
Control functionality in use.
If the parameter is set to enabled, following parameters are used to determine
the value of Discontinuous transmission period value, minimum step size for SIR
target modification and SIR target modification interval
•ULFastOLPCDTXthld
•FOLPCStepSizSIRTgt
•FOLPCSIRTgtModInt
which makes the OLPC to adjust the SIR target of the call faster.
Otherwise, legacy handling i.e. internal constant values are followed to determine these values.
Related features
Faster OLPC (standard)
FemtoHandoverControl (Femto Handover Control)
Description
This parameter determines whether or not the Femto Handover Control feature is
enabled in the RNC. When the Femto Handover Control feature is enabled in the
RNC, the RNC excludes specified neighbour cells from the neighbour cell lists that
are signaled to the UE in CELL_DCH state of connected mode. Consequently, intrafrequency, inter-frequency and inter-system handovers are disabled to the specified
neighbour cells when the Femto Handover Control feature is enabled in the RNC.
If the Femto Handover Control feature is disabled in the RNC, all neighbour
cells are included in the neighbour cell lists that are signaled to the UE in
CELL_DCH state of connected mode and subscribers are allowed to make handovers to all neighbour cells.
The parameters ADJS–AdjsSIB, ADJI–AdjiSIB and ADJG–AdjgSIB specify the
intra-frequency, inter-frequency and GSM neighbour cells which are excluded from
the neighbour cell lists that are signaled to the UE in CELL_DCH state.
Note that this parameter or the Femto Handover Control feature does not have
any effect to the information broadcasted in the System Information Block
11&12&18 messages.
Related features
Femto Handover Control (optional)
FlexULRLCEnabled (Flexible UL RLC Enabled)
Description
DN70456011
This parameter enables/disables use of feature Flexible UL RLC. If the parameter
is enabled (1), then feature Flexible UL RLC is used in the RNC. If the parameter is
disabled (0), then feature Flexible UL RLC is not used in the RNC.
Id:0900d80580a2e11c
Confidential
161
Summary of changes
Related features
Radio Network Parameters in Flexi Direct
( HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional) OR HSUPA 60 Users per
BTS (optional) ) AND HSDPA with QPSK and 5 Codes (optional) AND HSDPA
Dynamic Resource Allocation (optional)
HSUPADynBLEREnabled (HSUPA Dynamic BLER Enabled)
Description
This parameter Enables/Disables the Dynamic adjustment of HSUPA BLER.
Dynamic HSUPA BLER estimation algorithm defines BLER target for peak data
rate, bursty data rate and continuous data rate separately
Related features
HSUPA Basic 3 users per BTS (optional) OR HSUPA Basic 12 users per BTS
(optional) OR HSUPA Basic 24 users per BTS (optional)
IFHOOverIurExt (IFHO Over Iur Extension)
Description
This parameter enables or disables the IFHO Over Iur Enhancements functionality
introduced by IUR Mobility Enhancements feature in the RNC.
Related features
I-BTS Sharing (optional)
LFDProfEnabled (LFD profiling Enabled)
Description
LFD (Legacy Fast Dormancy) profiling Enabled parameter Enables/Disables the
use of LFD Profiling in RNC.
Related features
Fast Dormancy Profiling (optional)
PPACEnabled (Paging Permission With Access Control Enabled)
Description
The parameter defines whether or not the PPAC feature is enabled in the RNC.
When enabled in the RNC, this feature introduces possibility for UE to answer to
paging message or perform routing or location update even though the access class
of the UE is barred.
The feature is out of use in the RNC if the value of this parameter is set to
'Disabled'.
Before enabling the feature the paging response restriction per CN domain shall
be defined with parameter RNAC - PagingRestrictionInd and the routing/location
area update restriction per CN domain shall be defined with parameter RNAC –
RAU_LAU_RestrictionInd. By default all paging responses and RAU/LAU are
restricted.
Related features
Paging Permission with Access Control (standard)
PTTEnabled (Push to talk enabled)
162
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The parameter enables/disables RAN2300 Optimized push to talk experience
feature. It also allows/denies use of different transport channel types for UE with
push to talk (PTT) RAB. If the transport type is not allowed to be used, then that configuration is not used for PTT UE.
If the parameter value is changed, then the new value is used just for the RAB
setups done after the parameter change (already setup RABs are not affected).
The following alternatives can be used:
- feature is disabled
- DCH/DCH allowed
- DCH/DCH and DCH/HS-DSCH allowed for radio bearers
- DCH/DCH, DCH/HS-DSCH and E-DCH/HS-DSCH allowed for radio bearers
- all supported combinations allowed (also SRBs on HSPA and SRBs on
HSUPA).
Use of different transport channel types can be defined also based on Traffic
Class and Traffic Handling Priority with the parameters: FDPCHAndSRBOnHSPATC, EDCHQOSClasses and HSDSCHQoSclasses. PTT RAB is handled there
according of it's Traffic Class received from core network in RAB parameters.
Notice: If use of some configuration for PTT is enabled with this parameter, it
does not mean directly that configuration will be used, because use of different configurations depends on UE and BTS capabilities, other activated features and
resource situation in RAN.
Notice: feature is not supported by NB/RSxxx BTS, so it must not be activated
if there are those BTSs under the RNC.
Related features
Optimised push to talk experience (optional)
SIBCapabilityCheck (SIB Capability Check)
Description
This parameter defines whether or not SIB Capability Check feature is enabled in
the RNC. If this parameter is set as Enabled then RNC will calculate the size of
ASN.1 Encoded data for SIB11, SIB11bis and SIB12.
Related features
SIB11 Capability Check (standard)
SRVCCEnabled (SRVCC Enabled)
Description
The parameter indicates whether Single Radio Voice Call Continuity (RAN2435)
functionality is enabled in the RNC or not.
SRVCC functionality is activated in the cell only if both parameters SRVCCEnabled (for RNC)and IncomingLTEISHO (for cell) are in state Enabled. SRVCC from
LTE feature needs license for RAN2067 LTE Interworking-ISHO from LTE
Related features
SRVCC from LTE and CSFB with HO (optional)
RNHSPA
AARConfigTable (Application Aware RAN Configuration Table)
DN70456011
Id:0900d80580a2e11c
Confidential
163
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the configuration table needed for each application group in
case of Application Aware RAN feature. This parameter indicates that Application
Group Id, DSCP codes (upto 5 unique codes), Precedence and Target SPI for each
Initial SPI value assigned to the corresponding application group.
In case of Application Aware RAN feature a maximum of 6 Application groups
can be defined and for each Application Group a maximum of five unique DSCP
codes are allowed.
For each Application Group a unique Precedence value is assigned. Precedence value dictates what SPI should be chosen when packets belonging to
multiple application groups are detected by the RNC. In such cases the target SPI
shall be defined by the Application group having the lowest precedence value. The
lowest value of precedence means highest priority during rule evaluation.
With Application Aware RAN feature ,Initial SPI of the radio bearer is demoted
or promoted in the RNC PDCP layer according to Deep Packet Inspection (DPI)
marking. Operator can configure the promotion/demotion of the initial SPI or not to
change the initial SPI for certain type of data as pleased. Target SPI indicates the
new SPI value assigned to an application group after promotion or demotion of inital
SPI or no change action.
Child parameters
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Related features
Application Aware RAN (optional)
AppGrpId
DSCPCode1
DSCPCode2
DSCPCode3
DSCPCode4
DSCPCode5
Precedence
TargetSPIforSPI0
TargetSPIforSPI1
TargetSPIforSPI10
TargetSPIforSPI11
TargetSPIforSPI2
TargetSPIforSPI3
TargetSPIforSPI4
TargetSPIforSPI5
TargetSPIforSPI6
TargetSPIforSPI7
TargetSPIforSPI8
TargetSPIforSPI9
AARConfigTable/AppGrpId (Application Group Identifier)
164
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
Identifier of the Application Group in case of Application Aware RAN feature.A set
of applications requiring the same treatment at RAN might be grouped by the
operator into Application Groups. There can be maximum of six Application Groups
defined by the operator in case of Application Aware RAN feature.
Default value or special value '255' means that the Application Group Identifier
has not been defined by the operator and hence cannot be used.Allowed range is
1 to 6 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/DSCPCode1 (DSCP Code1)
Description
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature. One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/DSCPCode2 (DSCP Code2)
Description
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature.One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/DSCPCode3 (DSCP Code3)
DN70456011
Id:0900d80580a2e11c
Confidential
165
Summary of changes
Description
Radio Network Parameters in Flexi Direct
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature.One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/DSCPCode4 (DSCP Code4)
Description
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature.One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/DSCPCode5 (DSCP Code5)
Description
This parameter defines the DSCP code assigned to a corresponding Application
Group incase of Application Aware RAN feature.One Application Group may
contain IP packets marked with different DSCP codes. Hence in case of Application
Aware RAN feature the operator can define a maximum of 5 DSCP codes per application group. DSCP Code1, DSCP Code2, DSCP Code3, DSCP Code4, DSCP
Code5 parameters indicate the 5 unique DSCP codes that can be assigned to an
application group.
Default value or special value '255' means that the DSCP code has not been
defined or assigned by the operator for the corresponding application group and
hence cannot be used. Allowed range is 0 to 63 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
VCPHSDPAPrevDuration (Duration of HSDPA prevention for Voice Call Priority)
166
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The parameter determines the minimum duration of HSDPA prevention for the
Voice Call Prioritisation during High Traffic Load.
The shorter the value of the parameter, the shorter duration the HSDPA prevention is applied. Correspondingly, the longer value of the parameter, the longer
duration the HSDPA prevention is applied.
Special value 0 means that AMR prioritisation is applied without HSDPA prevention.
The function is switched on/off by the WCEL-VoiceCallPriority parameter.
Related features
Voice Call Priorization during High Traffic Load (optional)
MaxEHARQReTxPSconv10 (E-DCH max number of retransmissions PS conv E-TTI 10)
Description
This parameter determines the maximum number of HARQ retransmissions for the
E-DCH MAC-d flow of the PS conversational or push to talk RAB when the E-TTI is
10 ms.
Information is signaled to UE using RRC: E-DCH MAC-d flow maximum number
of retransmissions information element and to BTS using NBAP: Maximum Number
of Retransmissions for E-DCH information element.
Use of too high or low value can cause voice quality problems (delay or data
loss).
Related features
Optimised push to talk experience (optional)
MaxEHARQReTxPSconv2 (E-DCH max number of retransmissions PS conv E-TTI 2)
Description
This parameter determines the maximum number of HARQ retransmissions for the
E-DCH MAC-d flow of the PS conversational or push to talk RAB when the E-TTI is
2 ms.
Information is signaled to UE using RRC: E-DCH MAC-d flow maximum number
of retransmissions information element and to BTS using NBAP: Maximum Number
of Retransmissions for E-DCH information element.
Use of too high or low value can cause voice quality problems (delay or data
loss).
Related features
Optimised push to talk experience (optional)
PowerOffsetEHARQPSConv (HARQ power offset for E-DCH MAC-d flow of PS conv)
Description
This parameter defines the HARQ power offset value for the E-DCH MAC-d flow of
the PS conversational or push to talk service. The parameter is applicable if another
E-DCH MAC-d flow than one of the signaling link can be multiplexed within the
MAC-e PDU with the E-DCH MAC-d flow of the PS conversational, or if the power
offset of the signaling link E-DCH MAC-d flow equals to 0 dB. Power offset value is
used for both E-TTI values 2 ms and 10 ms.
Use of high value wastes radio resources and use of low value can cause voice
quality problems.
Related features
Optimised push to talk experience (optional)
DiscardTimerPTT (HSDPA Discard Timer for the PTT)
DN70456011
Id:0900d80580a2e11c
Confidential
167
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter defines the HSDPA Discard Timer value for the HS-DSCH MAC-d
flow of the PTT bearer. Discard Timer defines the time to live for a MAC-hs/ehs SDU
starting from the instant of its arrival into an HSDPA Priority Queue. BTS can use it
as delay information for guiding the scheduling.
Too small value can cause dropping the data too soon and too big value can
cause extra delay for data. In both cases the voice quality is weaken.
Related features
Optimised push to talk experience (optional)
T1PTT (HSDPA re-ordering rel timer T1 for the PTT)
Description
The parameter defines the value of the HSDPA re-ordering release timer T1 for the
HS-DSCH MAC-d flow of the PTT bearer. In the expiration of the timer, the reordering entity in the UE releases MAC-ehs PDUs to the upper layers even though there
were outstanding PDUs with lower sequence numbers. BTS might use the timer to
stop the HSDPA retransmission of the associated MAC-ehs PDUs.
Too small or big value weakens the voice quality.
Related features
Optimised push to talk experience (optional)
VCPHSDPAUserIncr (HSDPA user increment for the Voice Call Priority)
Description
The parameter determines the HSDPA user increment for the Voice Call Prioritisation during High Traffic Load. The HSDPA user increment defines how fast the
original maximum number of HSDPA users in the cell is restored after HSDPA prevention ceases.
The Voice Call Prioritisation during High Traffic Load uses the temporary
maximum number of HSDPA users to limit HS-DSCH allocations in the cell during
high load. When the usage of the maximum number of HSDPA users ceases, the
original maximum number of HSDPA users is restored gradually. The value of the
parameter defines how many HSDPA users can be added per second after HSDPA
prevention ceases.
Special value (0) means that restoration happens immediately. The value 1
restores the original maximum number of HSDPA users slowly, the value 10
restores the original value fast. The fast or immediate restoration is seen as oscillation between low and high maximum number of users if load varies in the cell.
Temporary maximum number of HSDPA users is defined by the WCEL-VCPMaxHSDPAUsers parameter.
Usage of the function is controlled by the WCEL-VoiceCallPriority parameter.
Related features
Voice Call Priorization during High Traffic Load (optional)
MEHHSUPAUserIncr (HSUPA user increment for the Mass Event Handler)
168
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The parameter determines the HSUPA user increment for the Mass Event Handler.
The HSUPA user increment determines how fast the original maximum number of
HSUPA users in the cell is restored after the high load state ceases.
The Mass Event Handler uses the temporary maximum number of HSUPA
users to limit E-DCH allocations in the cell during the high load state. When the
usage of the maximum number of HSUPA users ceases, the original maximum
number of HSUPA users is restored gradually. The value of the parameter defines
how many HSUPA users can be added per second after the high load state ceases.
Special value (0) means that restoration happens immediately. The value 1
restores the original maximum number of HSUPA users slowly, the value 10
restores the original value fast. The fast or immediate restoration is seen as oscillation between low and high maximum number of users if load varies in the cell.
Temporary maximum number of HSUPA users is defined by the WCEL-MEHMaxHSUPAUsers parameter.
Related features
Mass Event Handler (optional)
InitialSPINRT (Initial SPI for PS NRT RAB)
Description
This parameter defines the Initial Scheduling Priority Indicator to be used for the PS
NRT HSPA or HSDPA RAB incase of Application Aware RAN feature. The Initial
Scheduling Priority Indicator for PS NRT HSPA/HSDPA RAB is set according to this
parameter when Qos Aware Scheduling feature is disabled while Application Aware
RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial Scheduling Priority Indicator is choosen
according to the principles defined by Qos Aware HSPA Scheduling feature ie
based on the TC/THP/ARP combination via RNPS-QosPriorityMapping parameter.
Values "5"(SPI 5) and "6" (SPI 6) define the Initial SPI to be either 5 or 6 for the
NRT bearers when the RAN1262 Qos feature is disabled to get better differentiation
when doing SPI promotion / demotions for the data between bearers .
Related features
Application Aware RAN (optional)
MaxReWaitTime2msTTI16 (Maximum reordering wait time parameter for MAC-es EDCH)
Description
The parameter allows operators to adjust MAC-es reordering buffer wait time for
NRT E-DCH 2ms TTI with HSUPA 16QAM. Online modifications affect new connections only.
Related features
HSUPA 2 ms TTI (optional) AND HSUPA 5.8 Mbps (optional) AND HSUPA
16QAM (optional)
AARConfigTable/Precedence (Precedence)
DN70456011
Id:0900d80580a2e11c
Confidential
169
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the precedence value assigned to a corresponding Application Group incase of Application Aware RAN feature.Precedence value dictates
what SPI should be chosen when packets belonging to multiple application groups
are detected by the RNC. The lowest value of precedence means highest priority.Default value or special value '255' means that the Precedence value has not
been defined by the operator for a given application group and hence cannot be
used.Allowed range is 1 to 6 with step size of 1.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
PTTRLCPDUSizeHSDSCH (RLC PDU size for PTT mapped to HS-DSCH)
Description
The parameter defines the possible RLC PDU sizes for PTT service in case of HSDSCH.
If the use of 656 is allowed with this parameter, then the selection of DL RLC
PDU size is done according of UE and BTS capability and activation of 656 with the
RNP parameter PDUSize656WithHSDSCH.
With the smaller value it takes more time to transfer data, but less power is
needed.
Related features
Optimised push to talk experience (optional)
AARConfigTable/TargetSPIforSPI0 (Target SPI for SPI 0)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 0 in case of Application Aware RAN feature. This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 0 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
0 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI1 (Target SPI for SPI 1)
170
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 1 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 1 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
1 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI10 (Target SPI for SPI 10)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 10 in case of Application Aware RAN feature.This parameter indicates the new SPI assigned to a given application group after promotion or
demotion of Initial SPI 10 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
10 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI11 (Target SPI for SPI 11)
DN70456011
Id:0900d80580a2e11c
Confidential
171
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 11 in case of Application Aware RAN feature.This parameter indicates the new SPI assigned to a given application group after promotion or
demotion of Initial SPI 11 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
11 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI2 (Target SPI for SPI 2 )
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 2 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 2 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
2 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI3 (Target SPI for SPI 3 )
172
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 3 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 3 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
3 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI4 (Target SPI for SPI 4)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 4 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 4 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
4 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI5 (Target SPI for SPI 5)
DN70456011
Id:0900d80580a2e11c
Confidential
173
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 5 in case of Application Aware RAN feature. This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 0 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
5 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI6 (Target SPI for SPI 6)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 6 in case of Application Aware RAN feature. This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 6 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
6 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI7 (Target SPI for SPI 7)
174
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 8 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 8 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
8 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI8 (Target SPI for SPI 8)
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 8 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 8 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
8 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
AARConfigTable/TargetSPIforSPI9 (Target SPI for SPI 9)
DN70456011
Id:0900d80580a2e11c
Confidential
175
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the value of the Target SPI choosen for an application group
with Initial SPI 9 in case of Application Aware RAN feature.This parameter indicates
the new SPI assigned to a given application group after promotion or demotion of
Initial SPI 9 or no change .
Default value or special value '255' means that the Target SPI for Initial SPI
9 has not been defined by the operator and hence cannot be used. Allowed range
is 0 to 11 with step size of 1.
Note that the Initial SPI for PS NRT HSPA/HSDPA RAB is set according to
the RNHSPA-InitialSPINRT parameter when Qos Aware Scheduling feature is
disabled while Application Aware RAN is enabled.
If Qos Aware HSPA Scheduling feature is enabled simultaneously with Application Aware RAN feature then the Initial SPI is choosen according to the principles
defined by Qos Aware HSPA Scheduling feature ie based on the TC/THP/ARP
combination via RNPS-QosPriorityMapping parameter.
Parent parameter
AARConfigTable
Related features
Application Aware RAN (optional)
MEHCQIFeedbackCycle (Temporary CQI feedback cycle for the Mass Event Handler)
Description
The parameter determines the temporary CQI feedback cycle for the Mass Event
Handler.
Temporary CQI feedback cycle is used for a user not using CPC if the number
of HSDPA users attains or exceeds the threshold defined by the parameter WCELMEHHSDPAUserNbrCQI.
The longer the CQI feedback value, the less UL interference caused by the
periodical CQI reporting of the HSDPA UE. The longer CQI feedback cycle may
affect negatively to HSDPA scheduling performance.
The function is switched on/off by the WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
SmartHSPATimeToTrigger (Time-to-trigger for Smartphone throughput measurement)
Description
Parameter defines the time-to-trigger values of the HS-DSCH MAC-d flow low utilisation measurement and E-DCH MAC-d flow low throughput measurement for the
identified Smartphone instead of the MACdflowutilTimetoTrigger and EDCHMACdFlowThroughputTimetoTrigger parameters.
Related features
Fast Dormancy Profiling (optional)
SmartHSPATputAveWin (Window size for Smartphone throughput measurement)
176
Description
Parameter defines the HS-DSCH and E-DCH sliding averaging window sizes of the
throughput measurements for the identified Smartphone instead of the MACdflowthroughputAveWin and EDCHMACdFlowThroughputAveWin parameters.
The throughput measurement measures the number of bits transmitted by
MAC-d entity during the sliding measurement window defined by this parameter.
Value 0 means that the MAC-d flow throughput measurement is not activated.
Related features
Fast Dormancy Profiling (optional)
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
RNMOBI
SmartLTELayeringServ (Smart LTE Layering service control)
Description
The parameter defines what services are allowed to be moved to LTE by Smart LTE
Layering feature. Only services of PS domain can be controlled with this parameter.
UEs with services not supported in LTE should not be redirected to LTE,
because it is possible that those UEs comes back to WCDMA right away.
Smart LTE Layering is enabled with the SmartLTELayeringEnabled parameter.
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
SmartLTELayeringPrevT (Timer for Smart LTE Layering Prevention)
Description
The parameter defines a minimum time that the UE must be in WCDMA system
after RRC Connection Setup Complete has been received or when Relocation
Request for PS service is received from LTE. An UE can be redirected to LTE by
Smart LTE Layering feature after the timer defined by this parameter expires. When
this timer is running the Smart LTE Layering is not triggered.
Setting timer value too low may cause ping pong redirections between WCDMA
and LTE. Setting timer value too high may cause that redirection to LTE is not triggered as frequently as would be most effective
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
RNPS
SmartInactTimerFACH (Inactivity Timer for Smart Phones in Cell_FACH)
Description
Inactivity Timer for Smart Phones in Cell_FACH is used on MAC -c to detect the idle
periods on data transmission (NRT RBs and SRBs) for the LFDphones in
CELL_FACH state. Based on this timer the MAC -c shall give No_Data indication to
RRC, which further can change the state of the UE from Cell_FACH state to the
Cell_PCH state (or URA_PCH state).
Related features
Fast Dormancy Profiling (optional)
SmartInactivityTimerDCH (Inactivity timer for Smartphone DCH)
Description
Parameter defines the time indicating how long the radio and transmission
resources are reserved for Smartphone after inactivity detection on DCH. The
parameter is used for the identified Smartphone instead of the InactivityTimerDownlinkDCH and InactivityTimerUplinkDCH parameters.
This parameter defines the value for each DCH bit rate in downlink and uplink.
Parameter value 255 means that Smartphone specific DCH inactivity timers
are not used.
Related features
Fast Dormancy Profiling (optional)
PTTDormancyTimer (PTT dormancy timer)
DN70456011
Id:0900d80580a2e11c
Confidential
177
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter defines how long the PTT RAB which is identified as inactive is
allowed to keep the dedicated resources for radio bearer. If the dormancy timer
expires, then the dedicated resources of PTT radio bearer are released.
DCH transport channel type resource release is done when inactivity has lasted
the time which is defined by the PTTDormancyTimer parameter. E-DCH and HSDSCH transport channel type radio resource release is done when NRT service
specific conditions based inactivity has lasted the time which is defined by the
PTTDormancyTimer parameter.
Too small value of this timer causes extra signaling and setup delay for PTT
service. Too big value of this timer causes wasting of RAN resources.
Related features
Optimised push to talk experience (optional)
MEHTVMPendingTime (Temporary TVM pending time for the Mass Event Handler)
Description
The parameter determines the increased TVM pending time during high load for the
Mass Event Handler.
If the high load state is detected based on the average length of the NRT scheduling queue, the increased TVM pending time is taken into use instead of the values
defined by the TrafVolPendingTimeUL and TrafVolPendingTimeDL parameters.
"Pending time after trigger" IE and "Tx interruption after trigger" IE are reconfigured
to UE.
The longer "Pending time after trigger" and "Tx interruption after trigger"
prevents UE from sending frequent and repetitive UL capacity requests and data
during high load. This will decrease UL interference and RACH load in the network.
Increased TVM pending time defined by this parameter is used only if the value
is longer than the values defined by the TrafVolPendingTimeUL and TrafVolPendingTimeDL parameters.
Functionality is switched on/off by the WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
RNRLC
AMRLCHSRACHPS (AM RLC configuration for PS NRT with HS-RACH)
Description
178
This parameter defines the retransmission parameters for the AM RLC of the PS
RAB using E-DCH in its data transfer direction on CELL_FACH state. The parameter enables to activate the RLC polling and status reporting triggers and define their
values. The parameter also defines whether the SDU discard or No_discard after
MaxDAT number of transmissions is used as the general SDU discard mode and
the values for the numbers of the transmissions of the RLC PDUs. The RLC entity
of the UE can be configured to use the in-sequence delivery of the SDUs.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Child parameters
•
•
•
•
•
•
•
•
•
•
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPSMaxDAT
AMRLCHSRACHPSMaxMRW
AMRLCHSRACHPSMaxRST
AMRLCHSRACHPSPeriodMax
AMRLCHSRACHPSPeriodMin
AMRLCHSRACHPSPollPDU
AMRLCHSRACHPSPollSDU
AMRLCHSRACHPSPollWin
AMRLCHSRACHPSTriggers
HSRACHAMRLCRespHSFACH
AMRLCHSRACHPS/AMRLCHSRACHPSMaxDAT (AM RLC MaxDAT transmissions
for PS NRT with HS-RACH)
Description
This parameter defines the value of the RLC protocol parameter MaxDAT for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter
defines the maximum number of transmissions for the AMD PDU, which is set equal
to the MaxDAT-1. The value of the parameter is signalled to the RLC entity of the
UE rounded up to the closest value allowed in the RRC signaling.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/AMRLCHSRACHPSMaxMRW (AM RLC MaxMRW transmissions
for PS NRT with HS-RACH)
Description
This parameter defines the value of the RLC protocol parameter MaxMRW for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter
defines the maximum number of transmissions for the move MRW command, which
is set equal to the MaxMRW-1. The value of the parameter is signalled to the RLC
entity of the UE rounded up to the closest value allowed in the RRC signalling. The
parameter is significant only if the SDU discard after MaxDAT retransmissions is
applied.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/AMRLCHSRACHPSMaxRST (AM RLC MaxRST transmissions
for PS NRT with HS-RACH)
Description
DN70456011
This parameter defines the value of the RLC protocol parameter MaxRST for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter
defines the maximum number of transmissions for the RLC RESET PDU, which is
set equal to the MaxRST-1. The value of the parameter is signalled to the RLC entity
of the UE rounded up to the closest value allowed in the RRC signalling.
Id:0900d80580a2e11c
Confidential
179
Summary of changes
Radio Network Parameters in Flexi Direct
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/AMRLCHSRACHPSPollPDU (AM RLC period Poll_PDU for PS
NRT with HS-RACH)
Description
This parameter defines the minimum value of the RLC protocol parameter
Poll_PDU for the AM RLC entity of the PS radio bearers when data is transferred
over HS-RACH on CELL_FACH state using E-DCH transport channel. The value of
the parameter indicates how often the sender polls the receiver in accordance with
the activation of the poll trigger 'polling every Poll_PDU PDU'. The value of the
parameter is expressed in relation to the size of the allocated transmission window
for the AMR RLC entity. It is transformed into the corresponding number of the AMD
PDUs rounding up to the closest integer and it is configured to the AM RLC entity.
Poll_PDU can be set to a bigger value with other means. The value is signalled to
the RLC entity of the UE rounded up to the closest value or down to the maximum
value allowed in the RRC signalling. The trigger is applied if it has been activated
with the "AM RLC status report triggers for PS NRT with HS-RACH" parameter.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/AMRLCHSRACHPSPollSDU (AM RLC period Poll_SDU for PS
NRT with HS-RACH)
Description
This parameter defines the value of the RLC protocol parameter Poll_SDU for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter indicates in number of the RLC SDUs how often the sender polls the receiver in accordance with the activation of the poll trigger 'polling every Poll_SDU SDU'. The value
is signalled to the RLC entity of the UE rounded up to the closest value or down to
the maximum value allowed in the RRC signalling. The trigger is applied if it has
been activated with the "AM RLC status report triggers for PS NRT with HS-RACH"
parameter.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/AMRLCHSRACHPSPollWin (AM RLC period Poll_Window for PS
NRT with HS-RACH)
Description
180
This parameter defines the value of the RLC protocol parameter Poll_window for the
AM RLC entity of the PS radio bearers when data is transferred over HS-RACH on
CELL_FACH state using E-DCH transport channel. The value of the parameter indicates how often the sender polls the receiver in accordance with the activation of
the poll trigger 'window based polling'. The value is signalled to the RLC entity of the
UE rounded up to the closest value allowed in the RRC signalling. The trigger is
applied if it has been activated with the "AM RLC status report triggers for PS NRT
with HS-RACH" parameter.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCSRB3n4RespTime (AM RLC round trip time for SRB3 and SRB4)
Description
The parameter defines the AMRLC Round Trip Time (RTT) for the data transfer for
SRB3 and SRB4 for all kinds of variations of transport channel used or SRB bitrate.
It is used to estimate the average response time from the moment when the AM
RLC entity sends an AMD PDU to its peer entity with the poll bit set to the receiving
moment of the corresponding status PDU. The RTT depends on the L1/L2 processing delay of the UE and the RNC, type of the reverse transport channel - DCH, HSDSCH or E-DCH, processing delay of the BTS, the Uu interface delay, and the Iub
transfer delay. The parameter is used to define the AM RLC status reporting and
polling period lengths.
Related features
Fast Cell_PCH Switching (optional)
AMRLCRespTimeHSSRB (AM RLC round trip time for SRBs with HS-RACH/HS-FACH)
Description
This parameter defines the AM RLC Round Trip Time (RTT) for the UL/DL SRB data
transfer when the singnalling radio bearer is mapped to HS-RACH in UL and HSFACH in DL on CELL_FACH state (UL SRB using E-DCH transport channel and DL
SRB using HS-DSCH transport channel). It is used to estimate the average
response time from the moment that the AM RLC entity sends an AMD PDU to its
peer entity with the poll bit set to the receiving moment of the corresponding status
PDU. The RTT depends on the L1/L2 processing delay of the UE and the RNC, processing delay of the BTS, the Uu interface delay, and the Iub transfer delay. The
parameter is used to define the AM RLC status reporting and polling period lengths.
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/HSRACHAMRLCRespHSFACH (AM RLC round trip time with HSRACH/HS-FACH)
Description
This parameter defines the AM RLC Round Trip Time (RTT) for the UL data transfer
when the radio bearer is mapped to the HS-RACH on CELL_FACH state using EDCH transport channel and the reverse transport channel is the HS-DSCH. It is
used to estimate the average response time from the moment that the AM RLC
entity sends an AMD PDU to its peer entity with the poll bit set to the receiving
moment of the corresponding status PDU. The RTT depends on the L1/L2 processing delay of the UE and the RNC, processing delay of the BTS, the Uu interface
delay, and the Iub transfer delay. The parameter is used to define the AM RLC
status reporting and polling period lengths.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/AMRLCHSRACHPSPeriodMax (AM RLC status period max for
PS NRT with HS-RACH)
DN70456011
Id:0900d80580a2e11c
Confidential
181
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the maximum status reporting period of the AM RLC in
relation to the RLC round trip time for the PS radio bearers when data is transferred
over HS-RACH on CELL_FACH state using E-DCH transpport channel. The
maximum value is used as the value of the AM RLC timers Timer_Poll,
Timer_poll_periodic, Timer_status_periodic, and Timer_MRW and Timer_RST in
accordance with their activations with the "AM RLC status report triggers for PS
NRT with HS-RACH" parameter. The value is configured as such to the RLC entity
of the RNC. The value is signalled to the RLC entity of the UE rounded up to the
closest value or down to the maximum value allowed in the RRC signalling.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCSRB3n4PeriodMax (AM RLC status period max for SRB3 and SRB4)
Description
The parameter defines the maximum status reporting period of the AM RLC in
relation to the RLC round trip time for SRB3 and SRB4 for all kinds of variations of
transport channel used or SRB bitrate. The maximum value is used as the value of
the AM RLC timers Timer_Poll, Timer_poll_periodic, Timer_status_periodic, and
Timer_RST in accordance to their activation with the appropriate "AM RLC status
report triggers" parameters. The values of the timers are configured as such to the
RLC entity of the RNC. The values of the timers are signalled to the RLC entity of
the UE rounded up to the closest value or down to the maximum value allowed in
the RRC signalling.
Related features
Fast Cell_PCH Switching (optional)
AMRLCPeriodMaxHSSRB (AM RLC status period max for SRBs with HS-RACH/HSFACH)
Description
This parameter defines the maximum status reporting period of the AM RLC in
relation to the RLC round trip time for the UL/DL SRB data transfer when the signalling radio bearer is mapped to HS-RACH in UL and HS-FACH in DL on on
CELL_FACH state (UL SRB using E-DCH transport channel and DL SRB using HSDSCH transport channel). The maximum value is used as the value of the AM RLC
timers Timer_Poll, Timer_poll_periodic, Timer_status_periodic, and Timer_MRW
and Timer_RST in accordance with their activations with the “AM RLC status report
triggers for SRB with FACH/RACH” parameter. The value is configured as such to
the RLC entity of the RNC. The value is signalled to the RLC entity of the UE
rounded up to the closest value or down to the maximum value allowed in the RRC
signalling.
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/AMRLCHSRACHPSPeriodMin (AM RLC status period min for PS
NRT with HS-RACH)
182
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the minimum status reporting period of the AM RLC for the
PS radio bearers when data is transferred over HS-RACH on CELL_FACH state
using E-DCH transport channel. The value of the parameter is set to the AM RLC
timers Timer_Poll_Prohibit and Timer_Status_Prohibit in accordance with their activations with the "AM RLC status report triggers for PS NRT with HS-RACH" parameter. The value is configured as such to the RLC entity of the RNC. The value is
signalled to the RLC entity of the UE rounded up to the closest value or down to the
maximum value allowed in the RRC signalling.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
AMRLCHSRACHPS/AMRLCHSRACHPSTriggers (AM RLC status report triggers for
PS NRT with HS-RACH)
Description
This enables to activate and deactivate the polling and status reporting triggers and
the RLC timers for the AM RLC entity of the PS RAB in HS-RACH on CELL_FACH
state using E-DCH transport channel in its data transfer direction. The following
triggers and timers and period definition methods are controlled with the parameter:
"Timer poll periodic" to set the timer for the timer-based polling,
"Timer status periodic" to set the timer for the timer-based status reporting,
"Timer poll" to set the timer for a sent poll,
"Timer poll prohibit" to set the timer for filtering out polls in the sender,
"Timer status" prohibit to set the timer for filtering out status reports in the
receiver,
"Poll PDU" to set the trigger polling every Poll_PDU PDU,
"Poll SDU" to set the trigger polling every Poll_SDU SDU,
"Poll window" to set the window-based polling trigger,
"Last transmission PDU poll" to set the polling trigger for the last AMD PDU
scheduled for the first transmission,
"Last retransmission PDU poll" to set the polling trigger for the last AMD PDU
scheduled for the retransmission,
"Missing PDU indicator" to set the receiver to detect the missing AMD PDUs,
"SDU discard after MaxDAT transmissions" to define statically whether the
SDU discard after MaxDAT retransmissions or No_discard after MaxDAT transmissions shall be used,
"In sequency delivery of SDUs in UE" to define whether the RLC entity of the
UE is to deliver the received SDUs upper layers in sequency regardless of the value
of the RAB attribute Delivery Order.
Parent parameter
AMRLCHSRACHPS
Related features
High speed Cell_FACH Uplink (optional)
RLCConfOptionFPS (RLC Conf option switch for Fast Cell_PCH Switching)
DN70456011
Id:0900d80580a2e11c
Confidential
183
Summary of changes
Radio Network Parameters in Flexi Direct
Description
RNC defines RLC parameters for new radio link based on the used service of the
UE during RRC state transition from CELL_PCH to CELL_DCH. If the RLC parameters defined for the new radio link are identical with the previous RLC configuration,
then RLC configuration does not need to change in UE or RNC RLC entity when
Fast Cell_PCH Switching functionality is applied. If Fast Cell_PCH Switching functionality is applied and the RLC parameters defined for the new radio link are not
identical with the previous RLC configuration, then there are two options. The first
option is that RLC parameter configuration is done in the legacy way. The second
option is that the existing RLC configuration is used during radio link setup and then
RLC parameters are reconfigured when UE is in cell_dch state. This parameter is
used to select the option.
This parameter is related to RNFC-FastPCHSwitchEnabled which is the feature
optionality parameter for Fast Cell_PCH Switching feature. Therefore RLCConfOptionFPS parameter is only relevant when corresponding feature optionality parameter (RNFC-FastPCHSwitchEnabled) is enabled
Related features
Fast Cell_PCH Switching (optional)
UMRLCPTTDiscardTime (UM RLC SDU discard time in UE for PTT)
Description
The parameter defines the SDU discard timer value for the UM RLC entity of the UE
for push to talk service. The value of the parameter is signaled as such to UE.
Discard time is applied in the uplink transmission.
With the default value of the parameter timer based SDU discard is not used
by the UE. This is selected as default, so that data would not be discarded too early
in setup cases (discard of setup data cause setup delay). After setup phase too low
or too high value can cause voice quality problems.
Related features
Optimised push to talk experience (optional)
RNTRM
ActivityFactorForHSPA/AfPTTDL (Activity Factor for PTT RAB in Downlink)
Description
This parameter defines the activity factor for the PTT transport bearer Connection
Admission Control reservation in downlink direction. The activity factor value 1
means that the transport layer bit rates are not scaled for the CAC function. The
value 0.50 for example means that the average part of the logical CAC input values
is scaled to half of the default value. After parameter modification, the new parameter value is taken into use at next new transport bearer establishment. The existing
bearers’ logical CAC reservations are not modified.
This parameter is applied when PTT RAB is on HSPA or R99 DCH transport
channels.
Parent parameter
ActivityFactorForHSPA
Related features
Transport Bearer Tuning (optional) AND Optimised push to talk experience
(optional)
ActivityFactorForHSPA/AfPTTUL (Activity Factor for PTT RAB in Uplink)
184
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the activity factor for the PTT transport bearer Connection
Admission Control reservation in uplink direction. The activity factor value 1 means
that the transport layer bit rates are not scaled for the CAC function. The value 0.50
for example means that the average part of the logical CAC input values is scaled
to half of the default value. After parameter modification, the new parameter value
is taken into use at next new transport bearer establishment. The existing bearers’
logical CAC reservations are not modified.
This parameter is applied when PTT RAB is on HSPA or R99 DCH transport
channels.
Parent parameter
ActivityFactorForHSPA
Related features
Transport Bearer Tuning (optional) AND Optimised push to talk experience
(optional)
DSCPBTSOMToOMS (DSCP for BTS OM towards OMS)
Description
This parameter specifies the Differentiated Services Code Point (DSCP) for BTS
O&M messages towards OMS. The DSCP value is used in IP packet to define PerHop-Behaviour.
Related features
IP Based Iub for Flexi WCDMA BTS (optional) OR Dual Iub for Flexi WCDMA BTS
(optional)
DSCPForGTPSignalling (DSCP for GTP signalling)
Description
This parameter specifies the Differentiated Services Code Point (DSCP) for GTP
signalling traffic. The DSCP value is used in IP packet to define Per-Hop-Behaviour.
The configured DSCP value is applied also for GTP ECHO REQUEST messages. The GTP ECHO functionality is activated for the Iu-PS interface with attribute
RNTRM - EchoRequestSending.
VCEL
DirectSCCEnabled (Direct SCC Enabled)
Description
This parameter determines if a serving HS-DSCH cell change procedure can be
started during anchoring immediately after the intra-frequency measurement event
1A or 1C triggered ASU procedure without waiting a new measurement report to
trigger the serving HS-DSCH cell change.
A new measurement report is required to trigger the serving HS-DSCH cell
change during anchoring if the value of this parameter is "Disabled".
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
FastActOfTargetServCell (Faster Activation Of Target Serving Cell)
DN70456011
Id:0900d80580a2e11c
Confidential
185
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter indicates whether the Faster Activation of Target Serving Cell functionality is enabled in the cell during anchoring.
When enabled in the cell, this functionality introduces faster activation of target
serving cell by applying HSPA SCC specific ATO values, see VCEL parameter
HSPASCCSpecificATO. HSPA SCC specific ATO (Activation Time Offset) value is
applied, when SCC is performed with RRC: RADIO BEARER RECONFIGURATION message, DL SRB is mapped to DCH and Delay Restriction Flag IE is used
(see parameter FastCompletionOfSCC). HSPA SCC specific ATO value enables
setting SCC activation time even more aggressive, without impacting other procedures.
The formula to calculate the absolute CFN with this new ATO value is the following:
Absolute CFN = AT - HSPASCCSpecificATO
where AT = the activation time, which RNC has produced internally for a synchronised radio link handling procedure. About AT calculation, see parameter
RNPS- ActivationTimeOffset.
The Faster Activation of Target Serving Cell is not applied if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
FastCompletionOfSCC (Faster Completion of SCC Procedure)
Description
This parameter indicates whether the Faster Completion of SCC Procedure functionality is enabled in the cell during anchoring.
When enabled in the cell, this functionality introduces faster completion of SCC
procedure by including the Delay Restriction Flag IE in RRC: RADIO BEARER
RECONFIGURATION message. Inclusion is done on condition that RL is not reconfigured during SCC and UE is rel6 or newer. The included IE indicates that UE shall
send RRC: RADIO BEARER RECONFIGURATION COMPLETE message as soon
as possible without waiting CFN to elapse, but still perform the serving cell change
based on received CFN.
The Faster Completion of SCC Procedure is not applied if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH)
Description
This parameter identifies the measurement control parameter set (FMCS object)
controlling the intra-frequency measurements of a user having standalone SRB
allocated on DCH during anchoring.
If the value of this parameter is "Not defined", the VCEL parameter RtFmcsIdentifier identifies the FMCS parameter set for standalone SRB during anchoring.
Related features
I-BTS Sharing (optional) AND Fast HSPA Mobility (optional)
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay)
186
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter determines how much the HS-DPCCH power offset update is
delayed after the active set update during anchoring. The delay enables that serving
HS-DSCH cell change (or the next active set update) can be executed immediately
after the previous active set update without waiting for the HS-DPCCH power offset
update procedure to complete.
Recommended value is 3000 ms. The HS-DPCCH power offset update is not
delayed during anchoring if the value of this parameter is 0 ms.
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
HSPASCCSpecificATO (HSPA SCC Specific ATO Value)
Description
This parameter indicates the range of the HSPASCCSpecificATO parameter during
anchoring. Range is from 0 ms to 300 ms with a step of 10 ms. Default value of the
parameter is 100 ms.
If too high value is applied, timing of synchronized SCC procedure is jeopardised.
If too low value is applied, synchronized SCC procedure is delayed.
The HSPASCCSpecificATO is not applied if either the value of VCEL parameter
FastActOfTargetServCell is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSPA Inter-RNC Cell Change (optional) AND Fast HSPA Mobility (optional)
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation)
Description
This parameter indicates whether the Power Offset Update Message Size Optimisation functionality is enabled in the cell during anchoring.
When enabled in the cell, this functionality introduces message size optimisation for RRC: PHYSICAL CHANNEL RECONFIGURATION message, which is used
to update HS-DPCCH power offsets. Unnecessary IEs (namely Downlink information common for all radio links IE and Downlink information per radio link list IE) are
omitted resulting that message size is reduced. In some cases it will reduce from 2
to 1 TB (Transport Block). Message size reduction leads to faster and more reliable
signaling.
The Power Offset Update message size is not optimised if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
Fast HSPA Mobility (optional) AND HSPA Inter-RNC Cell Change (optional)
SRBHopsIdentifier (SRB HOPS Identifier)
Description
This parameter identifies the parameter set (HOPS object) controlling the intra-frequency handovers of a user having standalone SRB allocated on DCH during
anchoring.
If the value of this parameter is "Not defined", the VCEL parameter RtHopsIdentifier identifies the HOPS parameter set for standalone SRB during anchoring.
Related features
I-BTS Sharing (optional) AND Fast HSPA Mobility (optional)
DN70456011
Id:0900d80580a2e11c
Confidential
187
Summary of changes
Radio Network Parameters in Flexi Direct
WACSetIdentifier (WAC Parameter Set Identifier)
Description
Pointer to the WAC object identifier. Defines the WAC parameter set to be used in
this Virtual cell.
WAC
PrxNoiseMaxTuneAbsolute (Absolute limit in uplink noise autotuning)
Description
The parameter sets absolute limit for uplink noise autotuning compared to PrxNoise
value. For example, Operator sets PrxNoise initial value to -101,5 dBm and parameter PrxNoiseMaxTuneAbsolute is set to value 2dB. This limits PrxNoise value
between -99,5 dBm and -103,5 dBm.
TrafVolPendingTimeDL (Downlink traffic volume measurement pending time after
trigger)
Description
This parameter indicates the time (in seconds) during which MAC-D of RNC is forbidden to send any new downlink capacity requests with the same RB id, even if the
triggering condition is fulfilled again.
This parameter also indicates the time (in seconds) during which MAC-D of
RNC is forbidden to send any new downlink release/downgrade requests due to low
utilised NRT DCH with the same dedicated transport channel, even if the triggering
condition is fulfilled again.
InactCPCBatOptT (Inactive CPC user with battery optimization timer)
Description
The parameter defines how long inactive CPC user that benefits from battery consumption optimization is kept in Cell_DCH state after time to triggers for HSDPA low
utilization and E-DCH low throughput have triggered.
When low utilization is detected for HSDPA MAC-d flow (MACdflowutilTimetoTrigger) and low throughput for E-DCH MAC-d flow (EDCHMACdFlowThroughputTimetoTrigger), the RB can be released. When this has happened to all the RBs
of the user, the user can be transferred to Cell_FACH state. Instead of state transition, the user can be kept longer in the Cell_DCH state. This timer defines how
much longer the user can be kept in Cell_DCH state even if it is inactive all the
period.
This timer is applied to users which have:
- Continuous Packet Connectivity activated (DTX and DRX parameters defined
with CPCPar send to BTS and UE)
- UE has not indicated that it does not benefit from battery consumption optimization (optional IE in RRC)
Related features
Continuous Packet Connectivity (optional)
InactCPCNoBatOptT (Inactive CPC user without battery optimization timer)
188
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The parameter defines how long inactive CPC user that does not benefit from
battery consumption optimization is kept in Cell_DCH state after time to triggers for
HSDPA low utilization and E-DCH low throughput have triggered.
When low utilization is detected for HSDPA MAC-d flow (MACdflowutilTimetoTrigger) and low throughput for E-DCH MAC-d flow (EDCHMACdFlowThroughputTimetoTrigger), the RB can be released. When this has happened to all the RBs
of the user, the user can be transferred to Cell_FACH state. Instead of state transition, the user can be kept longer in the Cell_DCH state. This timer defines how
much longer the user can be kept in Cell_DCH state even if it is inactive all the
period.
This timer is applied to users which have:
- Continuous Packet Connectivity activated (DTX and DRX parameters defined
with CPCPar send to BTS and UE)
- UE has indicated that it does not benefit from battery consumption optimization
(optional IE in RRC)
Related features
Continuous Packet Connectivity (optional)
InactHSRACH (Inactive HS-RACH capable UE)
Description
The parameter defines how long inactive HS-RACH capable UE is kept in Cell_DCH
state after time to triggers for HSDPA low utilization and E-DCH low throughput
have triggered when the HS-RACH is configured in the main cell of the UE active
set cells. The main cell is the cell having best CPICH EcNo value reported by the
UE.
When low utilization is detected for HSDPA MAC-d flow (MACdflowutilTimetoTrigger) and low throughput for E-DCH MAC-d flow (EDCHMACdFlowThroughputTimetoTrigger), the RB can be released. When this has happened to all the RBs
of the user, the user can be transferred to Cell_FACH state. Instead of state transition the user can be kept longer in the Cell_DCH state. This timer defines how much
longer the user can be kept in Cell_DCH state even if it is inactive all the period.
This timer is applicable only if UE is HS-RACH capable and the HS-RACH has
been configured in the "main cell" of the active set of the UE.
Note special value '255': UE capability of HS-RACH is not taken into account,
that is this timer is not used.
Related features
High speed Cell_FACH Uplink (optional)
InactNonCPCBatOptT (Inactive nonCPC user with battery optimization timer)
DN70456011
Id:0900d80580a2e11c
Confidential
189
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter defines how long inactive non CPC user that benefits from battery
consumption optimization is kept in Cell_DCH state after time to triggers for HSDPA
low utilization and E-DCH low throughput have triggered.
When low utilization is detected for HSDPA MAC-d flow (MACdflowutilTimetoTrigger) and low throughput for E-DCH MAC-d flow (EDCHMACdFlowThroughputTimetoTrigger), the RB can be released. When this has happened to all the RBs
of the user, the user can be transferred to Cell_FACH state. Instead of state transition the user can be kept longer in the Cell_DCH state. This timer defines how much
longer the user can be kept in Cell_DCH state even if it is inactive all the period.
This timer is applied to users which have:
- Continuous Packet Connectivity is not activated (DTX and DRX parameters
defined with CPCPar are not send to BTS and UE)
- UE has not indicated that it does not benefit from battery consumption optimization (optional IE in RRC)
Related features
Continuous Packet Connectivity (optional)
InactNonCPCNoBatOptT (Inactive nonCPC user without battery optimization timer)
Description
The parameter defines how long inactive non CPC user that does not benefit from
battery consumption optimization is kept in Cell_DCH state after time to triggers for
HSDPA low utilization and E-DCH low throughput have triggered.
When low utilization is detected for HSDPA MAC-d flow (MACdflowutilTimetoTrigger) and low throughput for E-DCH MAC-d flow (EDCHMACdFlowThroughputTimetoTrigger), the RB can be released. When this has happened to all the RBs
of the user, the user can be transferred to Cell_FACH state. Instead of state transition, the user can be kept longer in the Cell_DCH state. This timer defines how
much longer the user can be kept in Cell_DCH state even if it is inactive all the
period.
This timer is applied to users which have:
- Continuous Packet Connectivity is not activated (DTX and DRX parameters
defined with CPCP are not send to BTS and UE)
- UE has indicated that it does not benefit from battery consumption optimization
(optional IE in RRC)
Related features
Continuous Packet Connectivity (optional)
InactivityTimerDownlinkDCH/InactivityTimerDownlinkDCH128 (Inactivity timer for
downlink 128kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures. Timer is
defined separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerDownlinkDCH
InactivityTimerDownlinkDCH/InactivityTimerDownlinkDCH16 (Inactivity timer for
downlink 16kbps DCH)
190
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures. Timer is
defined separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerDownlinkDCH
InactivityTimerDownlinkDCH/InactivityTimerDownlinkDCH256 (Inactivity timer for
downlink 256kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures. Timer is
defined separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerDownlinkDCH
InactivityTimerDownlinkDCH/InactivityTimerDownlinkDCH320 (Inactivity timer for
downlink 320kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures. Timer is
defined separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerDownlinkDCH
InactivityTimerDownlinkDCH/InactivityTimerDownlinkDCH32 (Inactivity timer for
downlink 32kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures. Timer is
defined separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerDownlinkDCH
InactivityTimerDownlinkDCH/InactivityTimerDownlinkDCH384 (Inactivity timer for
downlink 384kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures. Timer is
defined separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerDownlinkDCH
DN70456011
Id:0900d80580a2e11c
Confidential
191
Summary of changes
Radio Network Parameters in Flexi Direct
InactivityTimerDownlinkDCH/InactivityTimerDownlinkDCH64 (Inactivity timer for
downlink 64kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures. Timer is
defined separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerDownlinkDCH
InactivityTimerDownlinkDCH/InactivityTimerDownlinkDCH8 (Inactivity timer for
downlink 8kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures. Timer is
defined separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerDownlinkDCH
InactivityTimerDownlinkDCH (Inactivity timer for downlink DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on downlink DCH before release procedures.
Default values:
8 kbps: 5 s
16 kbps: 5 s
32 kbps: 5 s
64 kbps: 3 s
128 kbps: 2 s
256 kbps: 2 s
320 kbps: 2 s
384 kbps: 2 s
Child parameters
•
•
•
•
•
•
•
•
InactivityTimerDownlinkDCH128
InactivityTimerDownlinkDCH16
InactivityTimerDownlinkDCH256
InactivityTimerDownlinkDCH32
InactivityTimerDownlinkDCH320
InactivityTimerDownlinkDCH384
InactivityTimerDownlinkDCH64
InactivityTimerDownlinkDCH8
InactivityTimerUplinkDCH/InactivityTimerUplinkDCH128 (Inactivity timer for uplink
128kbps DCH)
192
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures. Timer is defined
separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerUplinkDCH
InactivityTimerUplinkDCH/InactivityTimerUplinkDCH16 (Inactivity timer for uplink
16kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures. Timer is defined
separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerUplinkDCH
InactivityTimerUplinkDCH/InactivityTimerUplinkDCH256 (Inactivity timer for uplink
256kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures. Timer is defined
separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerUplinkDCH
InactivityTimerUplinkDCH/InactivityTimerUplinkDCH320 (Inactivity timer for uplink
320kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures. Timer is defined
separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerUplinkDCH
InactivityTimerUplinkDCH/InactivityTimerUplinkDCH32 (Inactivity timer for uplink
32kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures. Timer is defined
separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerUplinkDCH
DN70456011
Id:0900d80580a2e11c
Confidential
193
Summary of changes
Radio Network Parameters in Flexi Direct
InactivityTimerUplinkDCH/InactivityTimerUplinkDCH384 (Inactivity timer for uplink
384kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures. Timer is defined
separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerUplinkDCH
InactivityTimerUplinkDCH/InactivityTimerUplinkDCH64 (Inactivity timer for uplink
64kbps DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures. Timer is defined
separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerUplinkDCH
InactivityTimerUplinkDCH/InactivityTimerUplinkDCH8 (Inactivity timer for uplink 8kbps
DCH)
Description
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures. Timer is defined
separately for each bit rate.
Parameter value 255 (infinity) means that NRT DCH inactivity supervision is
not used.
Parent parameter
InactivityTimerUplinkDCH
InactivityTimerUplinkDCH (Inactivity timer for uplink DCH)
Description
194
The time indicating how long the radio and transmission resources are reserved
after silence detection on uplink DCH before release procedures.
Default values:
8 kbps: 5 s
16 kbps: 5 s
32 kbps: 5 s
64 kbps: 3 s
128 kbps: 2 s
256 kbps: 2 s
320 kbps: 2 s
384 kbps: 2 s
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Child parameters
•
•
•
•
•
•
•
•
Summary of changes
InactivityTimerUplinkDCH128
InactivityTimerUplinkDCH16
InactivityTimerUplinkDCH256
InactivityTimerUplinkDCH32
InactivityTimerUplinkDCH320
InactivityTimerUplinkDCH384
InactivityTimerUplinkDCH64
InactivityTimerUplinkDCH8
HSDPAinitialBitrateUL (Initial bitrate for HSDPA associated UL DCH)
Description
The parameter determines the initial bit rate for scheduling of the HSDPA associated UL DCH return channel.
Related features
HSDPA (optional) AND HSDPA Associated Uplink DPCH Scheduling (optional)
OR HSDPA (optional) AND HSDPA Associated Uplink DPCH Scheduling
(optional) AND 16 kbps Return Channel DCH Data Rate Support for HSDPA
(optional)
HSDPAInitialBRULStrNRT (Initial bitrate for HSDPA UL DCH for NRT with streaming)
Description
This parameter defines the initial bit rate for the scheduling of the HSDPA associated UL DCH return channel for NRT, when a simultaneous PS streaming Radio
Bearer exists.
Related features
HSDPA (optional) AND HSDPA Dynamic Resource Allocation (optional) AND
QoS Aware HSPA Scheduling (optional) AND Streaming QoS for HSPA
(optional)
EDCHMACdFlowThroughputRelThr (Low throughput threshold of the E-DCH MAC-d
flow)
Description
This parameter defines the low throughput threshold for the throughput measurement of the E-DCH MAC-d flow. The threshold is defined as a number of bits per
second. The throughput measurement measures the number of bits transmitted by
the E-DCH MAC-d flow during the sliding measurement window. The sliding measurement window is defined with the EDCHMACdFlowThroughputAveWin parameter. If the result of the throughput measurement is less than or equal to the
threshold, the EDCHMACdFlowThroughputTimetoTrigger or EDCHMACdFlowThroughputStrTimetoTrigger timer is started.
Related features
HSUPA (optional) AND HSUPA Basic RRM (optional)
EDCHMACdFlowThroughputTimetoTrigger (Low throughput time to trigger of the EDCH MAC-d flow)
DN70456011
Id:0900d80580a2e11c
Confidential
195
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the low throughput time to the trigger timer for the throughput measurement of the E-DCH NRT MAC-d flow. If the result of the throughput
measurement is lower than or equal to the EDCHMACdFlowThroughputRelThr, the
EDCHMACdFlowThroughputTimetoTrigger is started. If the result of the throughput
measurement is higher than the EDCHMACdFlowThoughputRelThr, the EDCHMACdFlowThroughputTimetoTrigger is stopped and reset. If the timer expires, the
E-DCH NRT MAC-d flow is released, assuming that also the corresponding HSDSCH NRT MAC-d flow is allowed to be released.
Related features
HSUPA (optional) AND HSUPA Basic RRM (optional)
MACdflowutilRelThr (Low utilisation threshold of the MAC-d flow)
Description
This parameter defines the low utilisation threshold of the throughput measurement
of the MAC-d flow.
The threshold is defined as a number of bits per second. The throughput measurement measures the number of bits transmitted by MAC-d during the sliding
measurement window.
Related features
HSDPA (optional) AND HSDPA Channel Switching (optional)
MACdflowutilTimetoTrigger (Low utilization time to trigger of the MAC-d flow)
Description
This parameter defines the low utilisation time to trigger the timer of the throughput
measurement of the MAC-d flow.
Related features
HSDPA (optional) AND HSDPA Channel Switching (optional)
HSDPAMaxBitrateUL (Maximum bit rate for HSDPA UL DCH return channel)
Description
The parameter defines the maximum user bit rate allowed in a cell for HSDPA UL
DCH return channel. It is applicable to the PS domain NRT RAB.
Related features
HSDPA (optional)
HSDPAMinBRULStrNRT (Min bitrate for HSDPA UL DCH for NRT with streaming)
Description
This parameter defines the minimum allowed uplink bit rate for the HSDPA associated UL DCH return channel for the NRT Radio Bearer that exists simultaneously
with a PS streaming Radio Bearer. This bit rate is used by the packet scheduler
when it is downgrading bit rates. The allocated bit rate corresponds to the highest
bit rate in the TFS from which the TFCS is constructed.
Related features
HSDPA (optional) AND HSDPA Dynamic Resource Allocation (optional) AND
QoS Aware HSPA Scheduling (optional) AND Streaming QoS for HSPA
(optional)
HSDPAminAllowedBitrateUL (Minimum bitrate for HSDPA associated UL DCH)
196
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The parameter determines the minimum allowed bit rate in the uplink that can be
allocated by the PS to the HSDPA associated UL DCH return channel when downgrading the bit rate. The allocated bit rate corresponds to the highest bit rate in the
TFS from which the TFCS is constructed.
Related features
HSDPA (optional) AND HSDPA Associated Uplink DPCH Scheduling (optional)
OR HSDPA (optional) AND HSDPA Associated Uplink DPCH Scheduling
(optional) AND 16 kbps Return Channel DCH Data Rate Support for HSDPA
(optional)
WaitTimeRRC/WaitTimeRRCbackground (RRC wait time for background causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Originating Background Call, Terminating
Background Call.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRCconversational (RRC wait time for conversational
causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is:
Originating Conversational Call, Terminating Conversational Call.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRCemergency (RRC wait time for emergency causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Emergency Call.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRCinterRATreselection (RRC wait time for inter-RAT reselection causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Inter-RAT cell re-selection, Inter-RAT cell
change order.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRCinteractive (RRC wait time for interactive causes)
DN70456011
Id:0900d80580a2e11c
Confidential
197
Summary of changes
Radio Network Parameters in Flexi Direct
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Originating Interactive Call, Terminating
Interactive Call.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRCregistration (RRC wait time for registration causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Registration, Detach.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRCstreaming (RRC wait time for streaming causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Originating Streaming Call, Terminating
Streaming Call.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRCsubscribed (RRC wait time for subscribed causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Originating Subscribed Traffic Call.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRChighPrioritySignalling (RRC wait time for high priority signalling causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Originating high priority signalling, Terminating high priority signalling.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRClowPrioritySignalling (RRC wait time for low priority signalling causes)
198
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Originating low priority signalling, Terminating low priority signalling.
Parent parameter
WaitTimeRRC
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
WaitTimeRRC/WaitTimeRRCother (RRC wait time for other causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Call re-establishment.
Parent parameter
WaitTimeRRC
WaitTimeRRC/WaitTimeRRCunknown (RRC wait time for unknown causes)
Description
Defines the value of the Wait Time included in the RRC: RRC Connection Reject
message, when the Establishment Cause value received originally in the RRC:
RRC Connection Request message is: Terminating - cause unknown.
Parent parameter
WaitTimeRRC
DCHUtilRelThrDL (Threshold for the downlink DCH release measurement)
Description
This parameter defines the release threshold for the release throughput measurement of the NRT DCH in downlink direction.
The threshold is defined as a number of bits per second. The release throughput
measurement measures the number of all transmitted bits during the sliding measurement window.
DCHUtilRelThrUL (Threshold for the uplink DCH release measurement)
Description
This parameter defines the release threshold for the release throughput measurement of the NRT DCH in the uplink. The threshold is defined as a number of bits per
second. The release throughput measurement measures the number of all correctly
received bits during the sliding measurement window.
MSActivitySupervision (Time supervision of user inactivity (for NRT RBs))
Description
The MSActivitySupervision timer is used in the RRC states CELL_PCH and
URA_PCH for supervising the inactivity of NRT RAB(s).
The timer starts when a state transition to either state is executed. The MSActivitySupervision timer stops when any activity of NRT RAB(s) is detected and the
MS is moved to the CELL_FACH or CELL_DCH state.
The timer restarts (from the initial value) when the inactivity of the NRT RAB(s)
is detected and the MS is moved back to the CELL_PCH or URA_PCH state again.
In the expiry of the MSActivitySupervision timer, when the first "inactive state indication" (that is, cell/URA update which does not cause the (re)initiation of the signalling or data flow) is received from the MS, the RNC asks SGSN to release the Iu
connection.
Note! If the parameter value is set to zero, the state transition to
CELL_PCH/URA_PCH is not allowed. When inactivity is detected in the
CELL_FACH state, the MS is switched to the idle mode.
DCHUtilRelTimeToTrigger (Time to trigger for the release throughput measurement)
DN70456011
Id:0900d80580a2e11c
Confidential
199
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the period of the time between timing of the release throughput goes below the release bit rate threshold and the timing of sending lower downgrade request.
Related features
Throughput based optimization of the PS algorithm (optional)
UL_DL_activation_timer (UL/DL activation timer)
Description
This timer is used on MAC -c to detect idle periods on data transmission (NRT RBs
and SRBs) for the UE, which is in Cell_FACH state. Based on this timer the MAC c shall give the No_Data indication to the RRC, which further can change the state
of the RRC from Cell_FACH state to the Cell_PCH state (or URA_PCH state).
TrafVolThresholdULLow (Uplink traffic volume measurement low threshold)
Description
This parameter defines, in bytes, the threshold of data in the RLC buffers of SRB0,
SRB1, SRB2, SRB3, SRB4 and all NRT RBs that triggers the uplink traffic volume
measurement report, when the UE is in Cell_FACH state. Otherwise, UE sends data
on RACH.
This parameter is sent to the UE using an RRC: MEASUREMENT CONTROL
message.
TrafVolPendingTimeUL (Uplink traffic volume measurement pending time after trigger)
Description
This parameter indicates the time (in seconds) during which UE is forbidden to send
any new traffic volume measurement reports with the same traffic volume event
identity, even if the triggering condition is fulfilled again.
This parameter also indicates the time during which the UE blocks DTCH transmissions on the RACH after a measurement report is triggered.
The parameter is sent to UE using an RRC: MEASUREMENT CONTROL
message.
This parameter also indicates the time (in seconds) during which MAC-D of
RNC is for bidden to send any new uplink release/downgrade request due to low
utilised NRT DCH with same dedicated transport channel, even if the triggering condition is fulfilled again.
WACChangeOrigin (WAC Change origin)
Description
This parameter defines the origin of the last configuration action affecting the object.
WACId (WAC Identifier)
Description
Identifies the WAC object instance uniquely. The default parameter set is in the
WAC object instance with WACId=1.
WaitTimeRRC (Wait time in RRC connection request rejection)
200
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
Defines the value of the parameter Wait Time included in the RRC: RRC Connection Reject message. The MS waits for at least the duration of the time period specified in the parameter before it sends a new RRC: RRC Connection Request
message, or enters idle mode if the maximum number of attempts has already been
reached. Value 0 of the parameter indicates that repeated requests are not allowed.
The value of the parameter is dependant on the value of the Establishment
Cause received originally in the RRC: RRC Connection Request message. Cause
values are classified to particular cause groups, and each group corresponds to a
management parameter: WaitTimeRRCconversational, WaitTimeRRCstreaming,
WaitTimeRRCinteractive, WaitTimeRRCbackground, WaitTimeRRCsubscribed,
WaitTimeRRCemergency, WaitTimeRRCinterRATreselection, WaitTimeRRCregistration, WaitTimeRRChighPrioritySignalling, WaitTimeRRClowPrioritySignalling,
WaitTimeRRCunknown, WaitTimeRRCother.
NOTE: If RNC traffic manager notices overload situation and sends RRC: RRC
Connection Reject message before starting any call control entities, RNC traffic
manager does not use values defined in WAC-WaitTimeRRC parameter, but RNC
traffic manager uses its own methods to define optimal wait time (normally 4 sec).
Child parameters
•
•
•
•
•
•
•
•
•
•
•
•
WaitTimeRRCbackground
WaitTimeRRCconversational
WaitTimeRRCemergency
WaitTimeRRChighPrioritySignalling
WaitTimeRRCinterRATreselection
WaitTimeRRCinteractive
WaitTimeRRClowPrioritySignalling
WaitTimeRRCother
WaitTimeRRCregistration
WaitTimeRRCstreaming
WaitTimeRRCsubscribed
WaitTimeRRCunknown
DCHUtilRelAveWin (Window size for the release throughput measurement)
Description
This parameter defines the release sliding measurement window size for uplink and
downlink NRT dedicated channels. The release sliding measurement window is
used in the release throughput measurement. The release throughput measurement measures the number of received/sent bits in UL/DL NRT DCH during the
sliding measurement window period. The measurement window size is common for
all NRT DCH data rates (8, 16, 32, 64, 128, 256, and 384 kbps).
The value 0 s of this parameter means that release throughput measurement
is not active.
Related features
Throughput based optimization of the PS algorithm (optional)
EDCHMACdFlowThroughputAveWin (Window size of E-DCH MAC-d flow throughput
measurement)
DN70456011
Id:0900d80580a2e11c
Confidential
201
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the size of the sliding averaging window for the throughput
measurement of the E-DCH MAC-d flow. The throughput measurement measures
the number of bits transmitted by the E-DCH MAC-d flow during the sliding measurement window. The value 0 of the parameter means that the E-DCH MAC-d flow
throughput measurement is not performed.
Related features
HSUPA (optional) AND HSUPA Basic RRM (optional)
MACdflowthroughputAveWin (Window size of the MAC-d flow throughput measurement)
Description
This parameter defines the averaging window size for the throughput measurement
of the MAC-d flow.
The throughput measurement measures the number of bits transmitted by
MAC-d during the sliding measurement window. The sliding measurement window
is defined with the parameter MACdflowthroughputAveWin. Value 0 means that the
MAC-d flow throughput measurement is not activated.
Related features
HSDPA (optional) AND HSDPA Channel Switching (optional)
WBTS
RRMULDCHActivityFactor/RRMULActivityFactorPTT (Average relative UL data rate for
RBs of PTT)
Description
The parameter defines the average UL data rate in relation to its maximum allocated
transport channel data rate for the RB of the PTT RAB.
Too small value can drive a cell to overload, because too many PTT users
are admitted. Too big value causes extra congestion for the PTT service.
Parent parameter
RRMULDCHActivityFactor
Related features
Optimised push to talk experience (optional)
PWSMEnableWakeUpTime (Enable cell activation based on time of day)
Description
This parameter defines whether a non-remaining cell that was previously shut down
becomes active regardless of the traffic when the shutdown time limit ends. The end
of the shutdown time limit is controlled by the following parameters:
WBTS – PWSMShutdownEndHour,
WBTS – PWSMShutdownEndMin
Related features
Power Saving Mode for BTS (optional)
NBAPCommMode (NBAP Communication Mode)
Description
This parameter defines the used communication mode for NodeB via NBAP interface. For the I-HSPA adapter, it has only one valid value. It is added merely for internal, technical reasons.
Related features
Basic functions (standard)
PWSMAVTrafficVERLogic (Traffic verification logic in PWSM cell activation process)
202
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the traffic verification logic in PWSM cell activation process
of non-remaining cells.
When the value of the parameter is set to “All criteria”, all criteria for different
RB types have to be fulfilled to attempt the cell activation. When the value of the
parameter is set to “At least one criterion”, at least one criterion for one RB type has
to be fulfilled to attempt the cell activation. When the value of the parameter is set
to “RT and NRT HSDPA power or any other criteria”, either the criteria for both RT
and NRT HSDPA power have to be fulfilled or any other criteria for any RB type
have to be fulfilled to attempt the cell activation.
Related features
Power Saving Mode for BTS (optional)
WBTSSWBuildId (WBTS SW build identifier)
Description
This parameter indicates the BTS SW build version information. RNC gets the
parameter value from BTS NE.
WCEL
HSRACHTransmisBackOff (Additional E-DCH transmission back off for HS-RACH)
Description
This parameter determines the Additional E-DCH transmission back off for HSRACH. The time has been defined as the terms of TTIs. For DTCH/DCCH transmissions, the UE calculates maximum period for collision resolution phase from the
allowed start time of the E-DCH transmission. With E-TTI=10ms the allowed start
time of the E-DCH transmission is 1 + "Additional E-DCH transmission back off"
after start of the DPCCH transmission.
Related features
High speed Cell_FACH Uplink (optional)
AppAwareRANCapability (Application Aware RAN Capability)
Description
This parameter defines the Application Aware RAN capability of the local cell.
Related features
Application Aware RAN (optional)
AppAwareRANEnabled (Application Aware RAN Enabled)
Description
This parameter defines whether the feature Application Aware RAN is enabled or
not in the cell. The following functionalities can be activated/deactivated with this
parameter:
•dynamic service or application prioritization for the HSDPA scheduling
•dynamic demotion of UL bulk traffic
Prioritization can be done between bearers each carrying multiple services.
This parameter value is checked only for the serving HSDPA cell.
Related features
Application Aware RAN (optional)
AutoACResULOLThr (Automatic Access Class Restriction Uplink Overload Threshold)
DN70456011
Id:0900d80580a2e11c
Confidential
203
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the threshold for the UL interference load to start barring
access classes. The parameter defines the offset from the planned target level PrxTarget in case of non-HSPA cell and PrxMaxTargetBTS for HSPA configured cell.
Low offset value is used in case of non-HSPA cell and high offset value for
HSPA configured cell.
Related features
Automatic access class restriction (optional)
AutoACRPrxTotalAvgWs (Automatic Access Class window size for averaging PrxTotal)
Description
This parameter defines the window size for arithmetical averaging of PrxTotal measurement results. The parameter defines window size in terms of number of
samples of PrxTotal. The averaged value is used by Cell specific load control to
estimate overload situation in a cell. Detected overload can trigger restriction of
access classes in the cell. The higher the value is the higher is averaging and vice
versa.
Related features
Automatic access class restriction (optional)
HSRACHSubChannelNumber (Available Sub Channel Number for HS-RACH)
Description
This parameter determines the avaliable sub channel numbers used with HSRACH. When the HS-RACH is used, the information is signaled to UEs via
RRC:SIB5/5bis. Each bit indicates availability for a subchannel, where the subchannels are numbered "subchannel 0" to "subchannel 11". The value 1 of a bit indicates
that the corresponding subchannel is available and the value 0 indicates that it is
not available.
When the value ‘0000 0000 0000’ is set, the value is same than indicated in
the IE “Available Sub Channel Number” in the IE “PRACH system information list”
and defined by AllowedRACHSubChannels parameter.
Related features
High speed Cell_FACH Uplink (optional)
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No)
Description
This parameter determines the averaging window for the periodical CPICH Ec/No
measurement reporting, which is used as a criterion for the serving HS-DSCH cell
change procedure. Averaging is executed in the RNC.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNMOBI
(RNC level) parameter HSDPACPICHAveWindow determines the averaging
window for the periodical CPICH Ec/No measurement reporting.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
CodeTreeOptimisationGuardTime (Code Tree Optimisation Guard Time)
204
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter determines how long a DPCH must be allocated before it can be
reconfigured to a better position in the code tree.
The guard time secures that a serving HS-DSCH cell change or active set
update procedure can be executed immediately after the DPCH allocation without
waiting for the code tree optimisation procedure to complete. Recommended value
is 3 seconds in cells which are serving high mobility UEs.
The guard time is not used if either the value of this parameter is 0 s or the
value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
Fast HSPA Mobility (optional)
HSRACHImplicitRelease (Common E-DCH implicit release for HS-RACH)
Description
This parameter determines the use of Common E-DCH implicit release indicator.
The value other than infinity means that implicit release is in use and the value is
directly set in the "E-DCH transmission continuation back off" IE of SIB5/5bis when
the HS-RACH is used in the cell. Infinity means that implicit release is not in use and
other values that implicit release is in use.
Related features
High speed Cell_FACH Uplink (optional)
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell)
Description
This parameter determines the maximum allowed difference between the CPICH
Ec/No of the best active set cell and the CPICH Ec/No of the serving HS-DSCH cell.
If the difference between the averaged CPICH Ec/No values exceeds the value of
this parameter, serving HS-DSCH cell change procedure is initiated.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNMOBI
(RNC level) parameter HSDPAServCellWindow determines the maximum allowed
difference between the best active set cell and the serving HS-DSCH cell.
The WCEL parameters HSDPACPICHReportPeriod and HSDPACPICHAveWindow (or the corresponding RNMOBI parameters) determine the
reporting period of the periodical intra-frequency CPICH Ec/No measurement,
which is used as a criterion for the serving HS-DSCH cell change procedure, and
the averaging window for the periodical CPICH Ec/No measurement reports
respectively.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell selection)
DN70456011
Id:0900d80580a2e11c
Confidential
205
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter determines the maximum allowed difference between the CPICH
Ec/No of the best active set cell and the CPICH Ec/No of the serving HS-DSCH cell
when SRBs are mapped on E-DCH/HS-DSCH. If the difference between the
averaged CPICH Ec/No values exceeds the value of this parameter, serving HSDSCH cell change procedure is initiated. If the serving HS-DSCH cell change fails,
SRBs are switched to E-DCH/DCH or DCH/DCH configuration.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNHSPA
(RNC level) parameter HSDPASRBWindow determines the maximum allowed difference between the best active set cell and the serving HS-DSCH cell.
The WCEL parameters HSDPACPICHReportPeriod and HSDPACPICHAveWindow (or the corresponding RNMOBI parameters) determine the
reporting period of the periodical intra-frequency CPICH Ec/No measurement,
which is used as a criterion for the serving HS-DSCH cell change procedure, and
the averaging window for the periodical CPICH Ec/No measurement reports
respectively.
Related features
Fractional DPCH (optional) AND Fast HSPA Mobility (optional)
DefMeasCtrlReading (Deferred Measurement Control Reading)
Description
This parameter indicates whether the Deferred Measurement Control Reading functionality is enabled in the cell.
When enabled in the cell, this functionality introduces faster RACH access for
Rel-7 and newer UEs by including the Deferred measurement control reading
support IE in SIB3. The included IE indicates to UE that reading of SIB11, SIB11bis
and SIB12 can be skipped before RACH access. This means that UE can send
RRC CONNECTION REQUEST, CELL UPDATE or URA UPDATE without reading
first the above mentioned SIBs.
This functionality speeds up setup times after cell selection/re-selection and
the gain depends on SIB contents and scheduling.
The Deferred Measurement Control Reading is not applied if either the value
of this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
Fast HSPA Mobility (optional)
DirectSCCEnabled (Direct SCC Enabled)
Description
This parameter determines if a serving HS-DSCH cell change procedure can be
started immediately after the intra-frequency measurement event 1A or 1C triggered ASU procedure without waiting a new measurement report to trigger the
serving HS-DSCH cell change.
A new measurement report is required to trigger the serving HS-DSCH cell
change if either the value of this parameter or the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
DRXCycleHSFACH (Discontinuous Reception Cycle HS-FACH)
206
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter indicates the length of the DRX Cycle during DRX operation in High
Speed CELL_FACH.
Related features
High speed Cell_FACH Uplink (optional)
HSFACHVolThrDLPTT (DL traffic volume measurement threshold of HS-FACH for PTT)
Description
The parameter defines, in bits, the threshold of data in the RLC buffers of PTT RB
that triggers the downlink traffic volume measurement report (capacity request) on
MAC, when UE is able to use HS-DSCH in Cell_FACH state in DL.
Below the threshold, RNC sends data on HS-FACH and UE is not moved to
Cell_DCH state.
Too low value of this parameter causes waisting of dedicated resources, delay
and signaling load, because UE is moved to Cell_DCH sate too easily.
Too high value of this parameter causes loading of common channels.
Related features
Optimised push to talk experience (optional)
SmartTrafVolThrDL (DL traffic volume threshold for Smartphone)
Description
The parameter defines, in bytes, the threshold of data in the RLC buffers of SRB3,
SRB4 and all NRT RBs that trigger the downlink traffic volume measurement report
(capacity request) on MAC, when UE is in Cell_FACH state. Otherwise, RNC sends
data on FACH. The parameter is used for the identified Smartphone instead of the
TrafVolThresholdDLLow parameter.
Related features
Fast Dormancy Profiling (optional)
AutoACDSACRestriction (Domain Specific Access Class Restriction)
DN70456011
Id:0900d80580a2e11c
Confidential
207
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the particular CN domain (CS/PS/both) and the Cell Access
Restriction for which the Access Classes are restricted to access the radio network
in the cell. The parameter can be set to following values:
Restrict CS and PS domain: Rel-6 or newer UE is restricted to access the RAN
for both CS and PS domain for all the ACs barred in the CN domain AC barred lists
in that cell.
Restrict PS Domain: Rel-6 or newer UE is restricted to access the RAN for the
PS domain for all the ACs barred in the CN domain specific AC barred list in that
cell.
Restrict CS Domain: Rel-6 or newer UE is restricted to access the RAN for
the CS domain for all the ACs barred in the CN domain specific AC barred list in
that cell.
Restrict PS Domain and Cell Access: Rel-6 or newer UE is restricted to access
the RAN for the PS domain for all the ACs barred in the CN domain specific AC
barred list in that cell and the Rel-5 or older UEs are restricted for all the ACs barred
in the Access Class Barred List in that cell.
Restrict CS Domain and Cell Access: Rel-6 or newer UEs are restricted to
access the RAN for the CS domain for all the ACs barred in the CN domain specific
AC barred list in that cell and the Rel-5 or older UEs are restricted for all the ACs
barred in the Access Class Barred List in that cell.
Restrict CS and PS domain and Cell Access: Rel-6 or newer UE is restricted
to access the RAN for both CS and PS domain for all the ACs barred in the CN
domain specific AC barred lists and the Rel-5 or older UEs are restricted for all the
ACs barred in the Access Class Barred List in that cell in that cell.
Cell Access Restriction: All the UEs regardless of the release version are
restricted to access the RAN (regardless of the CN domain) for all the ACs barred
in the Access Class Barred List in that cell.
Related features
Automatic access class restriction (optional)
DRXInterruptHSDSCHData (DRX Interruption by HS-DSCH data)
Description
This parameter indicates whether DRX operation in High Speed CELL_FACH can
be interrupted by HS-DSCH data or not.
Related features
High speed Cell_FACH Uplink (optional)
DBandHSDPAEnabled (Dual Band HSDPA Enabled)
208
Description
Parameter enables / disables the Dual Band Dual Cell HSDPA (DB-DC-HSDPA)
usage in the cell. Dual Cell HSDPA (DC-HSDPA) must be enabled in the DB-DCHSDPA cell.
DB-DC-HSDPA cannot be used simultaneously with MIMO for the UE. DB-DCHSDPA with the single cell HSUPA can be activated for the UE. MIMO configuration
is not specifically restricted in the DB-DC-HSDPA cell but MIMO can be used irrespective of the DB-DC-HSDPA configuration in the cell.
NOTE: DB-DC-HSDPA cell pair must be configured in the frequency bands,
which support Dual Band HSDPA operation. System supported DL band combinations are: I&VIII, II&IV or I&V.
Related features
Dual-Cell HSDPA 42Mbps (optional) AND Dual Band HSDPA 42 Mbps (optional)
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
EVAMCapability (EVAM capability)
Description
The RAN2482: Enhanced Virtual Antenna Mapping feature improves the performance of VAM by controlling the phase difference between the physical antennas.
This parameter defines the EVAM capability for a cell.
Related features
Virtual antenna mapping (optional)
EVAMInUse (EVAM in use)
Description
This parameter defines whether or not the RAN2482: Virtual antenna mapping
feature is enabled in the cell. This feature improves the performance of VAM by controlling the phase difference between the physical antennas.
Related features
Virtual antenna mapping (optional)
FastHSPAMobilityEnabled (Fast HSPA Mobility Enabled)
DN70456011
Id:0900d80580a2e11c
Confidential
209
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter indicates whether or not the Fast HSPA Mobility feature is enabled
in the cell. Before the feature is enabled in the cell, the system checks that the
maximum amount of Fast HSPA Mobility -capable cells does not exceeded the limit
set by the capacity license.
When the Fast HSPA Mobility feature is enabled in the cell, it is possible to
make use of the following parameters:
- WCEL - ActivationTimeOffset
- WCEL - ATOSRBsOnHSPA
- WCEL - SRBDCHFmcsId
- WCEL - SRBHSPAFmcsId
- VCEL - SRBDCHFmcsId
- ADJS - SRBHopsIdentifier
- ADJD - AdjdSRBHopsId
- VCEL - SRBHopsIdentifier
- WCEL - HSDPAMaxCellChangeRepetition
- WCEL - HSDPASRBWindow
- WCEL - HSDPACPICHReportPeriod
- WCEL - HSDPACPICHAveWindow
- WCEL - HSDPAServCellWindow
- WCEL - HSDPACellChangeMinInterval
- WCEL - FastCompletionOfSCC
- VCEL - FastCompletionOfSCC
- WCEL - HSPASCCSpecificATO
- VCEL - HSPASCCSpecificATO
- WCEL - FastActOfTargetServCell
- VCEL - FastActOfTargetServCell
- WCEL - PowerOffsetUpdMsgSize
- VCEL - PowerOffsetUpdMsgSize
- WCEL - HSPwrOffsetUpdateDelay
- VCEL - HSPwrOffsetUpdateDelay
- WCEL - DirectSCCEnabled
- VCEL - DirectSCCEnabled
- RNC - RRCConnSetupMsgSize
- WCEL - DefMeasCtrlReading
- WCEL - CodeTreeOptimisationGuardTime
Related features
Fast HSPA Mobility (optional)
FastActOfTargetServCell (Faster Activation Of Target Serving Cell)
210
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter indicates whether the Faster Activation of Target Serving Cell functionality is enabled in the cell.
When enabled in the cell, this functionality introduces faster activation of target
serving cell by applying HSPA SCC specific ATO values, see WCEL parameter
HSPASCCSpecificATO. HSPA SCC specific ATO (Activation Time Offset) value is
applied, when SCC is performed with RRC: RADIO BEARER RECONFIGURATION message, DL SRB is mapped to DCH and Delay Restriction Flag IE is used
(see parameter FastCompletionOfSCC). HSPA SCC specific ATO value enables
setting SCC activation time even more aggressive, without impacting other procedures. When applied, HSPASCCSpecificATO overrides other cell level ATO parameters during SCC.
The formula to calculate the absolute CFN with this new ATO value is the following:
Absolute CFN = AT - HSPASCCSpecificATO
where AT = the activation time, which RNC has produced internally for a synchronised radio link handling procedure. About AT calculation, see parameter
RNPS- ActivationTimeOffset.
The Faster Activation of Target Serving Cell is not applied if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
FastCompletionOfSCC (Faster Completion of SCC Procedure)
Description
This parameter indicates whether the Faster Completion of SCC Procedure functionality is enabled in the cell.
When enabled in the cell, this functionality introduces faster completion of SCC
procedure by including the Delay Restriction Flag IE in RRC: RADIO BEARER
RECONFIGURATION message. Inclusion is done on condition that RL is not reconfigured during SCC and UE is rel6 or newer. The included IE indicates that UE shall
send RRC: RADIO BEARER RECONFIGURATION COMPLETE message as soon
as possible without waiting CFN to elapse, but still perform the serving cell change
based on received CFN.
The Faster Completion of SCC Procedure is not applied if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
SRBDCHFmcsId (FMCS identifier for standalone SRB on DCH)
Description
This parameter identifies the measurement control parameter set (FMCS object)
controlling the intra-frequency measurements of a user having standalone SRB
allocated on DCH.
If the value of this parameter is "Not defined" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled", the WCEL parameter RtFmcsIdentifier identifies the FMCS parameter set for standalone SRB on DCH.
Related features
Fast HSPA Mobility (optional)
DN70456011
Id:0900d80580a2e11c
Confidential
211
Summary of changes
Radio Network Parameters in Flexi Direct
SRBHSPAFmcsId (FMCS identifier for standalone SRB on HSPA)
Description
This parameter identifies the measurement control parameter set (FMCS object)
controlling the intra-frequency measurements of a user having standalone SRB
allocated on HSPA.
If the value of this parameter is "Not defined" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled", the WCEL parameter HSPAFmcsIdentifier identifies the FMCS parameter set for standalone SRB on HSPA.
Related features
Fractional DPCH (optional) AND Fast HSPA Mobility (optional)
HappyBitDelayConHSRACH (Happy bit delay condition for HS-RACH)
Description
This parameter determines the value for the Happy bit delay condition information
element for HS-RACH. The information element is signalled to the UE using the
RRC:SIB/5bis message for the UEs on CELL_FACH state using HS-RACH. The UE
utilises information for setting the E-DCH related happy bit. The happy bit is signalled to the BTS in E-DPCCH.
Related features
High speed Cell_FACH Uplink (optional)
T321 (High Speed Cell FACH DRX operation timer)
Description
This parameter indicates the time the UE waits until initiating DRX operation in High
Speed CELL_FACH. UE enters HS-DSCH DRX cycle after the expiry of this timer
Related features
High speed Cell_FACH Uplink (optional)
HSFACHCapability (High Speed FACH Capability)
Description
Parameter indicates the high speed FACH capability of the cell.
Related features
High speed Cell_FACH DL (optional)
HSRACHCapability (High Speed RACH Capability)
Description
Parameter indicates the high speed RACH capability of the cell. The cell is HSRACH capable, if the BTS informs itself to be Common E-DCH Capable, E-AI
Capable and ACK-NACK and CQI Capable.
Related features
High speed Cell_FACH Uplink (optional)
HSRACHEnabled (High Speed RACH Enabled)
Description
The parameter enables / disables the use of HS-RACH in UL in the cell, that is the
use of HSUPA in the cell for the UE on CELL_FACH state.
Related features
High speed Cell_FACH Uplink (optional)
HSPwrOffsetUpdateDelay (HS-DPCCH power offset update delay)
212
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter determines how much the HS-DPCCH power offset update is
delayed after the active set update. The delay enables that serving HS-DSCH cell
change (or the next active set update) can be executed immediately after the
previous active set update without waiting for the HS-DPCCH power offset update
procedure to complete.
Recommended value is 3000 ms in cells which are serving high mobility UEs.
The HS-DPCCH power offset update is not delayed if either the value of this parameter is 0 ms or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
RXBurstHSFACH (HS-FACH Reception Burst)
Description
This parameter indicates the period within the DRX Cycle that the UE continuously
receives HS-DSCH.
Related features
High speed Cell_FACH Uplink (optional)
AmpliRatioOptHSRACH (HS-RACH amplitude ratio optimized for low/high bit rate)
Description
This parameter determines the use of low or high bit rate optimised reference amplitude ratios of E-DPCH(s) relative to the amplitude ratio of DPCCH for certain ETFC(s) in case of HS-RACH.
Related features
High speed Cell_FACH Uplink (optional)
HSRACHMPO (HS-RACH Measurement Power Offset)
Description
This parameter defines the HSDPA Measurement Power Offset signaled to BTS
when the HS-RACH is setup in the cell. Measurement Power Offset defines the
default power offset between HS-PDSCH and P-CPICH.
Related features
High speed Cell_FACH Uplink (optional)
MEHHSDPAUserNbrCQI (HSDPA CQI user number for the Mass Event Handler)
Description
The parameter determines the number of HSDPA users in the cell to trigger usage
of the increased CQI feedback cycle for the Mass Event Handler.
The increased CQI feedback value is valid for a user not using CPC. The value
for the temporary CQI feedback cycle to be used instead of the fixed 4 ms is defined
by the RNHSPA-MEHCQIFeedbackCycle parameter.
If the value 0 is set to the parameter, the increased CQI feedback cycle is used
for every HSDPA UE not using CPC.
The function is switched on/off by the WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
HSFACHRABDRAEnabled (HSFACH direct resource allocation for NRT HSPA RAB)
DN70456011
Id:0900d80580a2e11c
Confidential
213
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter enables/disables the use of the direct dedicated resource allocation
for HSPA (parameter RABDRAEnabled) to CELL_DCH state in case of HS RACH
is supported by RNC and HS RACH Capable (Rel8) UE.
If the parameter is set as disabled (default), HS RACH capable (Rel8) UE is
kept in high speed common channels (HS-DSCH and E-DCH) on CELL_FACH
state.
If the parameter is set as enabled, dedicated resource allocation is tried for PS
data of interactive and background traffic classes during the NRT RAB setup phase
as described in parameter RABDRAEnabled.
0 (Disabled): High speed common channels are preferred for HS RACH
Capable (Rel8)UE on Cell_FACH state.
1 (Enabled): Direct dedicated resource allocation for HSPA can be applied for
HS RACH Capable (Rel8) UE on Cell_FACH state.
Related features
High speed Cell_FACH Uplink (optional)
HSFACHRel8ConSetupEC (HSFACH Rel8UE EstCause mapping in RRC con setup)
Description
This parameter defines the Establishment Cause (EC) values which prefer new high
speed common channels (HS FACH/HS RACH) usage for Rel8 UEs.
Establishment Cause is RRC information element which is received from the
UE in the RRC message RRC Connection Request.
The value 1 means that certain Establishment Cause prefers high speed
common channels in the RRC connection setup.
The value 0 means that certain Establishment Cause prefers SRB mapping to
the dedicated channel (DCH) or to the dedicated high speed packet access channel
(HSPA i.e. on HS-DSCH/E-DCH) in the RRC connection setup.
Bit 9: Emergency call does not effect, SRBs of emergency call are always
mapped to DCH in the RRC connection setup.
The parameter FDPCHSetup defines allocation procedure of the F-DPCH in
the RRC connection setup.
The parameter HSFACHRABDRAEnabled defines when direct resource allocation of the dedicated channels for HSPA for Rel8 UE is not allowed after RAB
setup comes.
Related features
High speed Cell_FACH Uplink (optional)
HSPA128UsersPerCell (HSPA 128 Users per Cell)
214
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter determines whether the “HSPA 128 users per cell“ feature is
enabled in the cell or not. If this feature is enabled, a maximum of 128 HSDPA and
128 serving HSUPA users can be admitted per cell, if BTS also supports 128 HSPA
users per cell (Rel2 baseband HW).
If this feature is not enabled, the RNC allows only 16, 48, 64 or 72 HSDPA
users per cell (see HSDPA48UsersEnabled, HSDPA64UsersEnabled,
HSPA72UsersPerCell) and only 3, 12, 60 users per BTS or LCG or 72 HSUPA
users per cell (see HSUPAXUsersEnabled, HSPA72UsersPerCell).
User amounts can also be restricted with the following parameters:
- WCEL-MaxNumberEDCHCell
- WBTS-MaxNumberEDCHLCG
- WCEL-MaxNumberHSDSCHMACdFlows
- WCEL-MaxNumberHSDPAUsers
- WCEL-MaxNumbHSDPAUsersS
- WCEL-MaxNumbHSDSCHMACdFS
It is recommended to have features Continuous Packet Connectivity (CPCEnabled) and Fractional DPCH (FDPCHEnabled) enabled in the cell so that high
amount of HSPA users is possible. Also feature HSUPA Downlink Physical Channel
Power Control should be in use in BTS so that DL control channel power consumption is in lower level so that more resources is left for user data (more RT users and
more user data).
Note: Simultaneous usage of HSPA 128 users per cell and CPC (enabled with
parameter WCEL-CPCEnabled) requires license to be installed for ‘CPC for 128
HSPA Users’ in RNC and the feature administrative state set as “ON”. Otherwise
HSPA 128 users per cell cannot be enabled.
Related features
HSPA 72 Users Per Cell (optional) AND HSPA 128 users per cell (optional)
HSPASCCSpecificATO (HSPA SCC Specific ATO Value)
Description
This parameter indicates the range of the HSPASCCSpecificATO parameter.
Range is from 0 ms to 300 ms with a step of 10 ms. Default value of the parameter
is 100 ms.
If too high value is applied, timing of synchronized SCC procedure is jeopardised.
If too low value is applied, synchronized SCC procedure is delayed.
The HSPASCCSpecificATO is not applied if either the value of the WCEL
parameter FastActOfTargetServCell is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
HSUPA16QAMAllowed (HSUPA 16QAM usage allowed in a cell)
Description
DN70456011
This parameter is used to define whether the RNC allows the usage of 16QAM modulation for HSUPA. If the parameter is enabled, then the RNC can use the HSUPA
16QAM feature in a cell. If the parameter is disabled, then the RNC cannot use the
HSUPA 16QAM feature in a cell. The HSUPA 16QAM is allowed in the cell if the
MaxTotalUplinkSymbolRate has value "3" indicating the max symbol rate of 5760
kbps.
Id:0900d80580a2e11c
Confidential
215
Summary of changes
Related features
Radio Network Parameters in Flexi Direct
HSUPA 16QAM (optional) AND HSUPA 5.8 Mbps (optional)
MEHHSUPAUserNbr2msTTI (HSUPA E-DCH 2 ms TTI user number for the Mass
Event)
Description
The parameter determines the number of HSUPA users in the cell to trigger usage
of the E-DCH 10 ms TTI (E-DCH 2 ms TTI prevention) for the Mass Event Handler.
If the value 0 is set to the parameter, the E-DCH 10 ms TTI is used for every
HSUPA UE.
The function is switched on/off by the WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
HSUPAUserLimit16QAM (HSUPA user limit for 16QAM usage)
Description
This parameter defines the limit for the amount of active HSUPA users in a cell in
the process of determining the usage of HSUPA 16QAM with both fixed and flexible
UL RLC. It is also used to determine the fixed UL RLC PDU size with MAC-es.
For flexible UL RLC: If the amount of active HSUPA users in a cell is lower than
or equal to the threshold, defined by this parameter, the HSUPA 16QAM usage is
allowed with flexible UL RLC PDU size.
For fixed UL RLC: If the amount of active HSUPA users in a cell is lower than
or equal to the threshold defined by this parameter, the fixed UL RLC PDU size must
be 656 bits. Otherwise an UL RLC PDU size of 336 bits can be used. The HSUPA
16QAM usage is allowed if the UL RLC PDU size is 656 bits.
Related features
HSUPA 16QAM (optional)
DRXInactiveTimerHSFACH (Inactivity Supervision Timer of HS-FACH for DRX User )
Description
This timer is used on MAC -c to detect the idle periods on data transmission (NRT
HSPA RBs and SRBs) for the Rel8 and newer UEs on CELL_FACH using HSFACH with DRX Mode.
Based on this timer the MAC -c shall give No_Data indication to RRC, which
further can change the state of the UE from Cell_FACH state to the Cell_PCH state
(or URA_PCH state).
Related features
High speed Cell_FACH Uplink (optional)
EvamDInit (Initial phase offset)
Description
The RAN2482: Enhanced Virtual Antenna Mapping feature improves the performance of VAM by controlling the phase difference between the physical antennas.
This parameter defines the initial phase value when the E-VAM algorithm starts;
otherwise this is the constant phase offset.
Related features
Virtual antenna mapping (optional)
EvamTKeep (Keep time)
216
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The RAN2482: Enhanced Virtual Antenna Mapping feature improves the performance of VAM (Virtual antenna mapping) by controlling the phase difference
between the physical antennas. This parameter defines the time for which the
phase offset is kept at the optimum phase needed as input for the phase control
algorithm implemented at BTS.
Related features
Virtual antenna mapping (optional)
LayeringRRCRelEnabled (Layering in RRC Connection Release Enabled)
Description
This parameter defines whether the layering in RRC Connection Release is enabled
in the cell. Layering in RRC Connection Release directs UE to other frequency layer
in RRC Connection Release.
Target frequencies and frequency ranges are defined with parameters under
LayeringRRCConnRelTargFreq structure. If no target frequencies are defined, no
layering is done in RRC Connection Release due to Layering in RRC connection
Release.
Related features
Layering in RRC Connection Release (optional)
SIB11Length (Length of SIB11)
Description
This parameter shows the size of ASN.1 encoded data for SIB11. If RNFC-SIBCapabilityCheck is set as Enabled then special value of this parameter is considered
as size of SIB11 ASN.1 encoded data is greater than allowed limit and if RNFC-SIBCapabilityCheck is set as Disabled then special value is considered as size of SIB11
ASN.1 encoded data is not calculated.
Related features
SIB11 Capability Check (standard)
SIB11bisLength (Length of SIB11bis)
Description
This parameter shows the size of ASN.1 encoded data for SIB11bis. If RNFC-SIBCapabilityCheck is set as Enabled then special value of this parameter is considered as size of SIB11bis ASN.1 encoded data is greater than allowed limit and if
RNFC-SIBCapabilityCheck is set as Disabled then special value is considered as
size of SIB11bis ASN.1 encoded data is not calculated.
Related features
SIB11 Capability Check (standard)
SIB12Length (Length of SIB12)
Description
This parameter shows the size of ASN.1 encoded data for SIB12. If RNFC-SIBCapabilityCheck is set as Enabled then special value of this parameter is considered
as size of SIB12 ASN.1 encoded data is greater than allowed limit and if RNFC-SIBCapabilityCheck is set as Disabled then special value is considered as size of SIB12
ASN.1 encoded data is not calculated.
Related features
SIB11 Capability Check (standard)
MEHLoadStateTtT (Load state time-to-trigger for the Mass Event Handler)
DN70456011
Id:0900d80580a2e11c
Confidential
217
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter determines the load state time-to-trigger for the Mass Event
Handler.
The Mass Event Handler uses the load state time-to-trigger for setting the load
state on and off. If the averaged queue length attains or exceeds the threshold
defined by the WCEL-MEHQueueThreshold parameter, the load state functions will
be taken into use after the time-to-trigger defined by the WCEL-MEHLoadStateTtT
parameter expires. If the averaged queue length goes below the threshold defined
by the WCEL-MEHQueueThreshold parameter, the load state functions will cease
after the time-to-trigger defined by the WCEL-MEHLoadStateTtT parameter multiplied by two expires.
The shorter the value of the parameter, the faster the load state functions turn
on and off. Correspondingly, the longer the value of the parameter, the slower the
load state functions turn on and off.
Available load state functions utilising time-to-trigger (controlled by the WCELMassEventHandler parameter):
- Increased TVM pending time
- Temporary maximum bit rate for UL DCH
- Temporary maximum number of HSUPA users
In addition to the Mass Event Handler, also the Automatic Access Class Restriction feature utilises the time-to-trigger for load detection.
Related features
Mass Event Handler (optional) OR Automatic access class restriction (optional)
MassEventHandler (Mass Event Handler functions)
Description
The parameter determines the Mass Event Handler functions in use.
The functions related to the Mass Event Handler:
Bit 0: Increased TVM pending time
Increased TVM pending time is taken into use during high load state.
Bit 1: Temporary maximum bit rate for UL DCH
Temporary maximum bit rate is set to minimum bit rate for UL DCH during high
load state.
Bit 2: Temporary maximum number of HSUPA users
Temporary maximum number of HSUPA users is taken into use during high
load state.
Bit 3: Increased CQI feedback cycle
Increased CQI feedback cycle is taken into use if the number of HSDPA users
in the cell exceeds a pre-defined threshold.
Bit 4: Load based E-DCH 2 ms TTI prevention
E-DCH 10 ms TTI in used instead of E-DCH 2 ms TTI if the number of HSUPA
users in the cell exceeds a pre-defined threshold.
Bit 5: UL load based AC for HSPA+ features
Single Cell HSDPA allocation is done instead of HSPA+, if the load based AC
exceeds the pre-defined threshold or the mass event load state of the cell is active.
Bit value 0: Function is disabled.
Bit value 1: Function is enabled.
Related features
Mass Event Handler (optional)
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HS-DSCH cell
changes)
218
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter determines the maximum number of repetitive serving HS-DSCH
cell changes during a predefined time period. If the maximum number of serving
HS-DSCH cell changes is exceeded, HS-DSCH is released. When the value of this
parameter is set to 0, the CTS to DCH due to repetitive SCC's is disabled.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNHSPA
(RNC level) parameter HSDPAMaxCellChangeRepetition determines the
maximum number of repetitive serving HS-DSCH cell changes during a predefined
time period.
The RNHSPA parameter HSDPACellChangeRepetitionTime determines the
time period during which the maximum number of repetitive serving HS-DSCH cell
changes is
counted.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
HSRACHMaxPeriodCollis (Max period for collision resolution phase for HS-RACH)
Description
This parameter determines the Maximum period for collision resolution phase. The
time has been defined as the terms of TTIs.
Related features
High speed Cell_FACH Uplink (optional)
PrxTargetPSMaxtHSRACH (Max PS target interference level with HS-RACH)
Description
This parameter defines the the maximum allowed target level for the UL PS NRT
DCH packet scheduling when the HS-RACH has been set up in the cell.
Related features
High speed Cell_FACH Uplink (optional)
PtxTargetPSMaxtHSRACH (Max PS target power level with HS-RACH)
Description
This parameter defines the the maximum allowed target level for the DL PS NRT
DCH packet scheduling when the HS-RACH has been set up in the cell.
Related features
High speed Cell_FACH Uplink (optional)
HSRACHMaxAllocTimeCCCH (Maximum E-DCH resource alloc time for CCCH for HSRACH)
Description
This parameter determines the maximum E-DCH resource allocation for CCCH.
The time has been defined as the terms of TTIs.
Related features
High speed Cell_FACH Uplink (optional)
HSRACHMaxTotSymbolRate (Maximum total uplink symbol rate of the HS-RACH)
DN70456011
Id:0900d80580a2e11c
Confidential
219
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter determines the planned maximum total uplink symbol rate of the
HS-RACH (maximum total symbol rate of the E-DPDCH(s) in CELL_FACH state) of
the UE in the cell.
The information is signaled to the UE using the RRC SIB5/5bis: Maximum channelization codes IE and is also signaled to the BTS using the NBAP PHYSICAL
SHARED CHANNEL RECONFIGURATION REQUEST message: Maximum Set of
E-DPDCHs IE within Common E-DCH System Information.
Related features
High speed Cell_FACH Uplink (optional)
MBLBLoadInfoDistr (MBLB Load Information Distribution)
Description
This parameter defines whether the HSPA load information (used in Multi-Band
Load Balancing) of the cell is distributed inside the RNC. This same information is
distributed also in case if any of Multi-Band Load Balancing triggers (MBLBRABSetupEnabled, MBLBStateTransEnabled, MBLBInactivityEnabled, MBLBMobilityEnabled) is enabled in the cell. If any of above triggering parameter and this parameter
is not enabled the HSPA load information of this cell is not distributed inside the
RNC meaning that HSPA load information of this cell is not available for Multi-Band
Load Balancing decision making. If the HSPA load information distribution is activated, HS-DSCH and E-DCH provided bit rate measurements are also activated in
the cell. It is better not to set this parameter enabled if the cell cannot be Multi-Band
Load Balancing target cell to avoid unnecessary internal message load and to avoid
unnecessary measurements to be activated.
Note! From the cell where HSDPA is not enabled the HSPA load information
is not distributed and HS-DSCH and E-DCH provided bit rate measurements are not
activated.
Related features
Multi-Band Load Balancing (optional)
HSDPACellChangeMinInterval (Minimum interval between serving HS-DSCH cell
changes)
Description
This parameter determines the minimum interval between serving HS-DSCH cell
changes when the periodical CPICH Ec/No reporting indicates that the maximum
allowed difference between the CPICH Ec/No of the best active set cell and the
CPICH Ec/No of the serving HS-DSCH cell is exceeded. Timer is started after every
successfully executed serving HS-DSCH cell change. During the time period,
serving HS-DSCH cell changes triggered by the periodical CPICH Ec/No reporting
are forbidden. If the value of this parameter is set to 0, serving HS-DSCH cell
changes are not restricted.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNMOBI
(RNC level) parameter HSDPACellChangeMinInterval determines the minimum
interval between serving HS-DSCH cell changes.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
HSRACHCommonEDCHRes (Number of Common E-DCH Resources for HS-RACH)
220
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the number of Common E-DCH Resources of the HS-RACH
configuration in the cell. Common E-DCH resource(s) is(are) setup in the cell when
the HS-RACH is setup in the cell. Common E-DCH resources configured during HSRACH setup are under direct control of the Node B and are shared by UEs in
CELL_FACH and IDLE mode. The RNC is not involved in the assignment of these
resources to UEs. Since only one cell is involved in the resource allocation, soft
handover is not possible.
Note that the number of configured Common E-DCH resources is practically
same as maximum number of HS-RACH user can send data within same TTI on
HS-RACH in the cell.
Related features
High speed Cell_FACH Uplink (optional)
ActivationTimeOffset (Offset for activation time)
Description
This parameter determines the offset value that is added to the activation time,
which RNC has produced internally for a synchronised radio link handling procedure. Connection Frame Number (CFN) which is set to the "activation time" fields of
the NBAP and RRC messages indicate the activation time of the reconfiguration.
Value of the CFN is produced by adding (modulo 256) the sum of the RRC message
length and the calculated SRB bit rate dependent offset value, and the value of this
parameter to the current CFN provided by the Frame Protocol (FP). Activation time
offset represents the AM RLC retransmissions of the SRB and the processing delay
of RNC and BTS. This parameter is applicable when the DL SL is mapped on DCH.
Too low activation time offset value increases the possibility of UE and radio
interface failures. Too high activation time offset value delays the mobility control of
the fast moving UEs.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNPS (RNC
level) parameter ActivationTimeOffset determines the offset for the activation time.
Related features
Fast HSPA Mobility (optional)
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA)
Description
This parameter determines the offset value that is added to the activation time,
which RNC has produced internally for a synchronised radio link handling procedure. Connection Frame Number (CFN) which is set to the "activation time" fields of
the NBAP and RRC messages indicate the activation time of the reconfiguration.
Value of the CFN is produced by adding (modulo 256) the value of this parameter
to the current CFN provided by the Frame Protocol (FP). This parameter is applicable when the SRBs are mapped on E-DCH/HS-DSCH.
Too low activation time offset value increases the possibility of UE and radio
interface failures. Too high activation time offset value delays the mobility control of
the fast moving UEs.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNHSPA
(RNC level) parameter ATOSRBsOnHSPA determines the offset for the activation
time.
Related features
Fractional DPCH (optional) AND Fast HSPA Mobility (optional)
DN70456011
Id:0900d80580a2e11c
Confidential
221
Summary of changes
Radio Network Parameters in Flexi Direct
OffsetToBeginCTCHBSIndex (Offset to Begin CTCH Block Set Index)
Description
Controls the frequency of idle schedule messages for Service Area Broadcast.
Smaller values mean more frequent scheduling and faster response, but increase
UE battery consumption. Values below 16 restrict maximum message size gradually. The parameter is a pointer to the first CTCH Block Set (BS) of the next CBS
Schedule Period relative to the CTCH BS index of the first part of the current BMC
Schedule Message.
With the default value 255 scheduling time period is the longest having long
intervals in sending the block sets thus consuming the least UE battery capacity.
OffsetToBeginCTCHBSIndex parameter is applicable when WCEL-SABEnabled is set as Enabled.
Related features
( Service Area Broadcast (optional) OR SAB Support with 2 SCCPCHs (optional)
) AND Terminal Battery Drain Prevention in Cell Broadcast (optional)
EvamNumPhaseOffset (Phase offset amount)
Description
The RAN2482: Enhanced Virtual Antenna Mapping feature improves the performance of VAM (Virtual antenna mapping) by controlling the phase difference
between the physical antennas. This parameter defines the number of phase
offsets needed for the phase control algorithm implemented in BTS.
Related features
Virtual antenna mapping (optional)
PowerOffsetPreamHSRACH (Power Offset Last Transmitted Preamble for HS-RACH)
Description
This parameter defines the power offset between the last transmitted preamble and
the initial power of the DPCCH transmission ("Power offset P p-e") in HS-RACH (the
Enhanced Uplink in CELL_FACH state and Idle mode).
Related features
High speed Cell_FACH Uplink (optional)
PowerOffsetUpdMsgSize (Power Offset Update Message Size Optimisation)
Description
This parameter indicates whether the Power Offset Update Message Size Optimisation functionality is enabled in the cell.
When enabled in the cell, this functionality introduces message size optimisation for RRC: PHYSICAL CHANNEL RECONFIGURATION message, which is used
to update HS-DPCCH power offsets. Unnecessary IEs (namely Downlink information common for all radio links IE and Downlink information per radio link list IE) are
omitted resulting that message size is reduced. In some cases it will reduce from 2
to 1 TB (Transport Block). Message size reduction leads to faster and more reliable
signaling.
The Power Offset Update message size is not optimised if either the value of
this parameter is "Disabled" or the value of the WCEL parameter FastHSPAMobilityEnabled is "Disabled".
Related features
Fast HSPA Mobility (optional)
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No)
222
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter determines the reporting period of the CPICH Ec/No measurement,
which is used as a criterion for the serving HS-DSCH cell change procedure.
If the value of this WCEL parameter is "Not defined" or the value of the WCEL
parameter FastHSPAMobilityEnabled is "Disabled", the corresponding RNMOBI
(RNC level) parameter HSDPACPICHReportPeriod determines the reporting
period of the CPICH Ec/No measurement.
Related features
HSDPA Serving Cell Change (optional) AND Fast HSPA Mobility (optional)
MEHQueueThreshold (Scheduling queue threshold for the Mass Event Handler)
Description
The parameter determines the scheduling queue threshold for the Mass Event
Handler.
The Mass Event Handler uses the scheduling queue threshold for detection of
the load state. If the averaged queue length attains or exceeds the threshold defined
by this parameter, the load state functions will be taken into use after time-to-trigger
defined by the WCEL-MEHLoadStateTtT parameter expires.
The lower the value of the parameter, the lower load is needed to trigger the
load state functions on. Correspondingly, the higher the value of the parameter, the
higher load is needed to trigger load state functions on.
The available load state functions utilising the scheduling queue length (controlled by the WCEL-MassEventHandler parameter):
- Increased TVM pending time
- Temporary maximum bit rate for UL DCH
- Temporary maximum number of HSUPA users
In addition to the Mass Event Handler, also the Automatic Access Class Restriction feature utilises the scheduling queue length for load detection.
Related features
Mass Event Handler (optional) OR Automatic access class restriction (optional)
SABEnabled (Service Area Broadcast Enabled)
Description
This parameter enables Service Area Broadcast in a WCDMA cell. If the parameter
value is set as Enabled, Service Area Broadcast is activated. When it is set to Disabled, there will not be any Service Area Broadcast handling in the WCEL.
For activation of RAN2527 SAB Support with 2SCCPCHs, License for legacy
SAB and RAN 2527 are required.
Related features
Service Area Broadcast (optional) OR SAB Support with 2 SCCPCHs (optional)
SmartLTELayeringEnabled (Smart LTE Layering Enabled)
DN70456011
Id:0900d80580a2e11c
Confidential
223
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter indicates whether or not the Smart LTE Layering feature is enabled
in the cell. It also defines what triggering points are used. The following two triggering points are available:
- RRC state change of the UE away from CELL_DCH state
- channel type switch from HSPA or from HSDPA to DCH.
- CS RAB release.
Channel type switch means here cases where HS-DSCH is tried to be switched
to DCH (E-DCH/HS-DSCH --> DCH/DCH or DCH/HS-DSCH --> DCH/DCH) with
some other bit rate than 0 (pure release cases are excluded).
CS RAB release trigger means case where an UE has CS RAB and at least
one active PS RAB and then CR RAB is released (UE would stay in CELL_DCH
state in WCDMA).
Cell specific CPICH RSCP threshold for the functionality is set with the SmartLTELayeringRSCP parameter.
Cell specific user amount threshold for the functionality is set with the SmartLTELayeringUA parameter.
Services that the UE to be redirected to LTE can be using are set with the SmartLTELayeringServ parameter.
The minimum time that the UE must be in WCDMA system after RRC Connection Setup Complete has been received or when Relocation Request for PS service
is received is set with the parameter SmartLTELayeringPrevT.
Redirection allowance to FDD LTE, TDD LTE or both of them is set with the
SmartLTELayeringTSysSel parameter.
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
SmartLTELayeringUA (Smart LTE Layering NRT user amount threshold)
224
Description
The parameter defines a user amount threshold that must be exceeded before
Smart LTE Layering can be done. User amount is checked in cell level and just NRT
users (Interactive and Background) are counted.
An user is counted in those cells where the user in question has DCH, HSDSCH or E-DCH.
If the NRT user amount check allows the Smart LTE layering, then it is not
prevented again right after NRT user amount is smaller than the parameter value,
but there is a fixed hysteresis of 5 users. When the user amount is more than 5
users below of the parameter value, then the Smart LTE layering is not allowed
anymore.
Checking of user amount can be deactivated by setting the value 0.
Real default value for this threshold cannot be defined, because it depends on
radio network planning.
If too small value is used, then too many UEs might be redirected to LTE and
there are free capacity in WCDMA side. If too big value is used, then too many UEs
stays in WCDMA side and so causes load there when there could be free capacity
in LTE side.
Smart LTE Layering is enabled with the SmartLTELayeringEnabled parameter.
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
SmartLTELayeringRSCP (Smart LTE Layering RSCP threshold)
Description
The parameter defines CPICH RSCP threshold that must be exceeded before
Smart LTE Layering can be done. The parameter can be used for example cases
where WCDMA and LTE cells are co-located and LTE cell has smaller coverage.
Checking of CPICH RSCP can be deactivated by setting the value 0.
Real default value for this threshold cannot be defined, because it depends on
radio network planning.
If too small value is used, then redirection can be done to too weak LTE cell
causing that UE comes back to WCDMA. If too big value is used, then redirection is
not done when it should be done.
Smart LTE Layering is enabled with the SmartLTELayeringEnabled parameter.
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
SmartLTELayeringTSysSel (Smart LTE Layering Target System Selection)
Description
The parameter indicates if the redirection is allowed to FDD LTE, TDD LTE or to
both of them. If redirection is prevented to FDD or to TDD, then neighbor frequencies in question are not given to UE at all.
The parameter is used only in those cells where the Smart LTE Layering feature
is activated (SmartLTELayeringEnabled).
Related features
LTE Interworking-Cell Reselection to LTE (optional) AND Smart LTE Layering
(optional)
EvamTSweep (Sweep time)
Description
The RAN2482: Enhanced Virtual Antenna Mapping feature improves the performance of VAM by controlling the phase difference between the physical antennas.
This parameter defines the time to search for the optimum phase needed as input
for phase control algorithm implemented at BTS.
Related features
Virtual antenna mapping (optional)
LayeringRRCConnRelTargFreq/TargetFrequency (Target frequency)
Description
This parameter defines the target frequency for layering in RRC connection release.
The frequencies are given in UTRA Absolute Radio Frequency Channel
Number (UARFCN) format, which defines the downlink channel number and the
downlink carrier frequency.
Default value 0 means that UE is not directed to other frequency in RRC
Connection Release due to Layering in RRC connection Release.
Parent parameter
LayeringRRCConnRelTargFreq
Related features
Layering in RRC Connection Release (optional)
LayeringRRCConnRelTargFreq (Target frequency for layering in RRC Connection
Release)
DN70456011
Id:0900d80580a2e11c
Confidential
225
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter structure defines the possible target frequencies for layering in RRC
connection release. Up to 8 different FDD UMTS frequencies can be defined. If
there are several target frequencies defined RNC fills the frequencies in round robin
order (in ICSU level) to consecutive RRC Connection Release messages at the cell.
Child parameters
•
Related features
Layering in RRC Connection Release (optional)
TargetFrequency
VCPMaxHSDPAUsers (Temporary max number of HSDPA users for the VCP)
Description
The parameter determines the temporary maximum number of HSDPA users
allowed during the HSDPA prevention for the Voice Call Prioritisation during High
Traffic Load.
The lower the value of the parameter, the fewer users are allowed during the
HSDPA prevention.
The function is switched on/off by the WCEL-VoiceCallPriority parameter.
Related features
Voice Call Priorization during High Traffic Load (optional)
MEHMaxHSUPAUsers (Temporary max number of HSUPA users for the Mass Event)
Description
The parameter determines the temporary maximum number of HSUPA users for
the Mass Event Handler.
The Mass Event Handler uses the temporary maximum number of HSUPA
users to limit E-DCH allocations during high load. Detection of the high load is based
on the average scheduling queue length. Threshold for the average scheduling
queue length is defined by the WCEL-MEHQueueThreshold parameter.
If the value 0 is set to the parameter, HSUPA allocations are prevented in the
cell during the high load state.
Usage of the temporary maximum number of HSUPA users is controlled by the
WCEL-MassEventHandler parameter.
Related features
Mass Event Handler (optional)
HSRACHActivityThr (Threshold of the E-DCH MAC-d flow of PS RB on HS-RACH)
Description
This parameter defines the activity threshold for the activity measurement of the EDCH MAC-d flow of PS RB on CELL_FACH state using HS-RACH. The threshold
is defined as a number of bits per second. The activity measurement measures the
number of bits transmitted by the E-DCH MAC-d flow during the sliding measurement window. The sliding measurement window is defined with the HSRACHActivityAveWin parameter. If the result of the activity measurement is more than or equal
to the threshold, the HSRACHActTimeTrigger is started.
Related features
High speed Cell_FACH Uplink (optional)
HSRACHActTimeToTrigger (Time to trigger for activity measurement on HS-RACH)
226
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the activity time to the trigger timer for the activity measurement of the E-DCH MAC-d flow of PS RB on CELL_RACH state using HS-RACH.
If the result of the activity measurement is higher than or equal to the HSRACHActivityThr, the HSRACHActTimeToTrigger is started. If the result of the activity measurement is lower than the HSRACHActivityThr, the HSRACHActTimeToTrigger is
stopped and reset. If the timer expires, it triggers a uplink capacity request with state
change request from CELL_RACH to CELL_DCH.
Related features
High speed Cell_FACH Uplink (optional)
HSRACHTimeToTrigger (Traffic volume measurement time to trigger of HS-RACH)
Description
This parameter defines, in ms, the period between the timing of event detection and
timing of sending a traffic volume measurement report for the UEs on CELL_FACH
state using HS-RACH in UL. This parameter is sent to the UE using an RRC: MEASUREMENT CONTROL message.
Related features
High speed Cell_FACH Uplink (optional)
UEDRXCapability (UE DRX in Cell_FACH capability)
Description
RAN1908: UE DRX in Cell_FACH feature enables discontinuous reception (UE
DRX) for High Speed Cell_FACH for Rel8 or newer UE releases. This parameter
defines the Cell specific UE DRX capability as received from the BTS.
Related features
High speed Cell_FACH Uplink (optional)
HSFACHDRXEnabled (UE DRX with High Speed Cell FACH Enabled)
Description
This parameter Enables/Disables the use of DRX in High Speed CELL_FACH in the
cell.
Related features
High speed Cell_FACH Uplink (optional)
MEHULLHSDPAUALimit (UL load based HSDPA user amount limit for the MEH)
DN70456011
Id:0900d80580a2e11c
Confidential
227
Summary of changes
Radio Network Parameters in Flexi Direct
Description
The parameter sets limit for the UL load based HSDPA user amount in the cell. If
the calculated UL load based HSDPA user amount exceeds this limit, then only SCHSDPA is possible to be used in the cell for new HS-DSCH allocations. The
purpose of the check is to control UL load caused by HSDPA users. This parameter
has no impact on UL transport channel type selection.
Calculation of UL load based HSDPA user amount takes into account the following things:
- HSDPA user type (SC/DC/MIMO)
- amount of CPC users of the cell
- amount of non-CPC users of the cell with normal CQI feedback cycle
- amount of non-CPC users with extended CQI feedback cycle (MEH)
- amount of DCH users of the cell
The UL load based HSDPA user amount check can be deactivated totally by
using value 0.
Too small value of the parameter prevents use of DC/ MIMO too easily causing
low DL peak rates.
Too big value of the parameter does not protect UL from extra L1 control
channel load caused by DC/MC/MIMO users leading to low user data throughput.
Also the mass event load state of the cell prevents the allocation of
DC/MC/MIMO, regardless of the value of MEHULLHSDPAUALimit.
With the default value 30, its possible to allocate:
- 18 MIMO/DC calls
- 11 MIMO/DC calls and 11 SC HSDPA calls
- 1 MIMO/DC call and 28 SC HSDPA calls
This with no UL DCH allocations in the cell and with normal CQI allocations (no
CPC users and no MEH CQI usage)
Notice, that WCEL – MassEventHandler must be also configured to activate
the functionality.
Related features
Mass Event Handler (optional)
HSRACHVolThrUL (UL traffic volume measurement threshold of HS-RACH)
Description
This parameter defines, in bytes, the threshold of data in the RLC buffers of SRB0,
SRB1, SRB2, SRB3, SRB4 and all NRT RBs that triggers the uplink traffic volume
measurement report, when the UE is in Cell_FACH state and using HS-RACH. Otherwise, UE sends data on HS-RACH. This parameter is sent to the UE using an
RRC: MEASUREMENT CONTROL message.
Related features
High speed Cell_FACH Uplink (optional)
SmartTrafVolThrUL (UL traffic volume threshold for Smartphone)
228
Description
The parameter defines, in bytes, the threshold of data in the RLC buffers of SRB3,
SRB4 and all NRT RBs that trigger the uplink traffic volume measurement report
(capacity request) on MAC, when UE is in Cell_FACH state. Otherwise, RNC sends
data on FACH. The parameter is used for the identified Smartphone instead of the
TrafVolThresholdULLow parameter.
Related features
Fast Dormancy Profiling (optional)
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
HSRACHExtendedAI (Use of Extended Acquisition Indicator HS-RACH)
Description
This parameter determines the use of Extended Acquisition Indicators (E-AI). TRUE
indicates that E-AI is used when HS-RACH is configured. FALSE indicates that EAI is not used when the HS-RACH is configured.
The original AICH signature space can be extended from 16 signatures (as
defined in Rel99) to totally 32 signatures by the using of the E-AI. Extended Acquisition Indicators (E-AI) represents a set of values corresponding to a set of E-DCH
resource configurations.
When the E-AI is used, indication is signaled to BTS by NBAP:PHYSICAL
SHARAED CHANNEL RECONFIGURATION message to UEs via RRC:SIB5/5bis.
Related features
High speed Cell_FACH Uplink (optional)
VoiceCallPriority (Voice Call Prioritisation During High Traffic Load)
Description
The parameter enables/disables the Voice Call Prioritisation During High Traffic
Load feature in the cell.
Related features
Voice Call Priorization during High Traffic Load (optional)
VCPPtxOffset (Voice Call Priority target threshold for HSDPA prevention)
Description
The parameter determines the level of the estimated non-controllable DL power to
start HSDPA prevention in the cell. The level is expressed in dB below WCEL-PtxTarget.
If the estimated non-controllable power is equal or higher than the level determined (PtxTarget – VCPPtxOffset), HSDPA prevention, that is the temporary
maximum number of HSDPA users (TMHD) determined by the WCEL-VCPMaxHSDPAUsers parameter, is taken into use.
The parameter provides possibility to use HSDPA prevention (TMHD) in a
reactive or proactive mode.
The reactive mode (default 0 dB) means that TMHD is taken into use when the
estimated non-controllable DL power meets PtxTarget. This is recommended value
if PtxOffset > 0 dB because AMR CS DCH user can be admitted up to (PtxTarget +
PtxOffset).
The proactive mode (value > 0 dB) means that TMHD is taken into use before
the estimated non-controllable DL power meets PtxTarget. This is recommended if
PtxOffset = 0 or very close to PtxTarget because HSDPA traffic is started to be
limited before possible AMR CS DCH congestion.
The function is switched on/off by the WCEL-VoiceCallPriority parameter.
Related features
Voice Call Priorization during High Traffic Load (optional)
WACSetIdentifier (WAC Parameter Set Identifier)
Description
Pointer to the WAC object identifier. Defines the WAC parameter set to be used in
this cell.
HSRACHActivityAveWin (Window size of E-DCH MAC-d flow of PS RB on HS-RACH)
DN70456011
Id:0900d80580a2e11c
Confidential
229
Summary of changes
Radio Network Parameters in Flexi Direct
Description
This parameter defines the size of the sliding averaging window for the activity measurement of the E-DCH MAC-d flow of PS RB when the UE is on CELL_FACH state
using HS-RACH. The activity measurement measures the number of bits transmitted by the E-DCH mac-d flow during the sliding measurement window. The value 0
of the parameter means that the E-DCH MAC-d flow activity measurement is not
performed.
Related features
High speed Cell_FACH Uplink (optional)
WRAB
L1BLERTEDCHPSConvSpe10 (BLER target for PS Conversational speech E-TTI 10
ms)
Description
This parameter defines the L1 BLER target for the E-DCH MAC-d flow of the PS
conversational speech RB (Source Statistics Descriptor PS core network has set as
a "speech" or in case of push to talk service) when the E-TTI equals to 10 ms. It is
used by the outer loop power control of the RNC. E-HARQ retransmission threshold
for the block error detection is defined with the management parameter "HARQ
threshold for OLPC of PS Conv Speech E-TTI 10 ms".
Use of too high value wastes radio resources and too low value causes voice
quality problems.
Value of the parameter equals to the log10 of the BLER value.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
L1BLERTEDCHPSConvSpe2 (BLER target for PS Conversational speech E-TTI 2 ms)
Description
This parameter defines the L1 BLER target for the E-DCH MAC-d flow of the PS
conversational speech RB (Source Statistics Descriptor PS core network has set as
a "speech" or in case of push to talk service) when the E-TTI equals to 2 ms. It is
used by the outer loop power control of the RNC. E-HARQ retransmission threshold
for the block error detection is defined with the management parameter "HARQ
threshold for OLPC of PS Conv Speech E-TTI 2 ms".
Use of too high value wastes radio resources and too low value causes voice
quality problems.
Value of the parameter equals to the log10 of the BLER value.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
EbNoDCHRateGain/EbNoDCHRateGainPSConvSpe (Data rate gain for the Eb/N0 of
the PS conv speech)
230
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
This parameter defines the value of the data rate gain for the planned Eb/N0s of the
DCHs which transfer the radio bearers of the PS conversational speech RABs. Data
services are generally encoded with Turbo, which becomes more efficient with the
higher data rates, in the same way as interleaving does. Higher transmission power
is used for the DPCCH with the higher data rates; it improves the channel estimation
and consequently the Eb/N0 performance. Therefore the rate matching Eb/N0s can
be reduced also for the low data rate bearers when they are transferred in the multiservice configuration of an aggregate data rate which is high enough. The selector
parameters "Data rate gain selector for the Eb/N0 of the UL DCH" and "Data rate
gain selector for the Eb/N0 of the DL DCH" define the physical channel data rates
(spreading factors) for which the data rate gain is valid. If the value of the selector
parameter shows that with the maximum DPDCH data rate the gain is applicable,
then the value of the actual gain parameter is added to the value of the rate
matching Eb/N0 value of the data service.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
The parameter is significant with the push to talk services. To modify this
parameter, you must manually lock and later unlock all WCEL objects related to this
WRAB. This will severely impact the network. You can avoid it by creating a new
WRAB and gradually transferring the WCELs to this one.
Parent parameter
EbNoDCHRateGain
Related features
Optimised push to talk experience (optional)
EbNoEDCHPSConvSpeech (Eb/N0 planned for E-DCH PS conversational speech)
Description
Parameter defines the planned Eb/N0 for E-DCHs which are transferring radio
bearers of the PS conversational speech RABs (value of Source Statistics Descriptor is "speech" or in case of push to talk service). Parameter is applied in the definition of the load factor which is used in admission control and packet scheduling
algorithms of the radio resource management.
Use of too high value wastes radio resources and too low value causes quality
problems.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
EDCHBLERAdjPSConvSpe10 (HARQ threshold for OLPC of PS Conv Speech E-TTI 10
ms)
DN70456011
Id:0900d80580a2e11c
Confidential
231
Summary of changes
Radio Network Parameters in Flexi Direct
Description
Management parameter defines the L1 HARQ retransmissions threshold for the
outerloop power control dedicated to the E-DCH MAC-d flow of the PS conversational speech RB (Source Statistics Descriptor PS core network has set as a
"speech" or in case of push to talk service) when the E-TTI equals to 10 ms. Its value
is used by the outer loop power control of the RNC for the detection of the block
error. Block error is occurred if the number of the retransmissions equals to the
value of the parameter or a HARQ failure has observed. Outerloop power control
adjusts the uplink DPCCH SIR target after the occurred block errors. This threshold
value is used when the BLER target has been defined with the management parameter “BLER target for PS Conversational speech E-TTI 10 ms”.
Use of too high or low value causes voice quality problems (delay or data loss).
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
EDCHBLERAdjPSConvSpe2 (HARQ threshold for OLPC of PS Conv Speech E-TTI 2
ms)
Description
Management parameter defines the L1 HARQ retransmissions threshold for the
outerloop power control dedicated to the E-DCH MAC-d flow of the PS conversational speech RB (Source Statistics Descriptor PS core network has set as a
"speech" or in case of push to talk service) when the E-TTI equals to 2 ms. Its value
is used by the outer loop power control of the RNC for the detection of the block
error. Block error is occurred if the number of the retransmissions equals to the
value of the parameter or a HARQ failure has observed. Outerloop power control
adjusts the uplink DPCCH SIR target after the occurred block errors. This threshold
value is used when the BLER target has been defined with the management parameter “BLER target for PS Conversational speech E-TTI 2 ms”.
Use of too high or low value causes voice quality problems (delay or data loss).
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Related features
Optimised push to talk experience (optional)
SIRDPCCHInitialEDCH (Initial SIR target for UL DPCCH with E-DCH)
232
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
Description
The parameter defines the initial SIR target for the UL DPCCH when the radio link
has E-DCH configured in the uplink transfer direction. The parameter is used only
in case of push to talk service.
The value of the parameter is used in the configuration of the SIR target for the
uplink outer loop power controller of the RNC.
The values of E-TTI for PTT initial SIR targets are defined assuming 1-way
receiver diversity. The Initial SIR target values for the 2- and 4-way receiver diversity
cases are achieved by adding particular offset values to the 1-way receiver diversity
values of the initial SIR targets. The offset values are defined with two management
parameters (SIRDPCCHInitialDCHRxDiv2 and SIRDPCCHInitialDCHRxDiv4).
The initial SIR target value is sent to the BTS and to the outer loop power controller of the RNC.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for a
cell.
Child parameters
•
•
Related features
Optimised push to talk experience (optional)
SIRDPCCHInitialEDCHPTT10MS
SIRDPCCHInitialEDCHPTT2MS
SIRDPCCHInitialEDCH/SIRDPCCHInitialEDCHPTT10MS (Initial SIR target for UL
DPCCH with E-TTI 10 ms - PTT)
Description
This parameter defines the initial SIR target of UL DPCCH when the radio link has
E-DCH configured with E-TTI=10ms for RB of PTT. One-way receiver diversity is
assumed.
Use of too high value wastes radio resources and too low value causes quality
problems.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
Parent parameter
SIRDPCCHInitialEDCH
Related features
Optimised push to talk experience (optional)
SIRDPCCHInitialEDCH/SIRDPCCHInitialEDCHPTT2MS (Initial SIR target for UL
DPCCH with E-TTI 2 ms - PTT)
Description
DN70456011
This parameter defines the initial SIR target of UL DPCCH when the radio link has
E-DCH configured with E-TTI=2ms for RB of PTT. One-way receiver diversity is
assumed.
Use of too high value wastes radio resources and too low value causes quality
problems.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
Id:0900d80580a2e11c
Confidential
233
Summary of changes
Radio Network Parameters in Flexi Direct
Parent parameter
SIRDPCCHInitialEDCH
Related features
Optimised push to talk experience (optional)
EbNoOfPSConvSpe/EbNoDCHOfPSConvSpe (Planned Eb/N0 of the PS conversational speech)
Description
This parameter defines the planned Eb/N0 for the PS conversational speech
service.
The management parameter EbNoDCHOfPSConvSpeQua defines the
appropriate value of the quality target. This parameter is applicable for all DCH user
data rates when the 1-way receiver diversity is assumed. The value of the parameter represents the low data rate value without the possible data rate gain. The data
rate gain value is defined separately with the management parameter EbNoDCHRateGainPSConvSpe. The decision whether the data rate gain is applied with a
particular physical channel data rate is done with the management parameters
EbNoDCHRateGainSFUp for uplink and EbNoDCHRateGainSFDown for downlink.
The final planned Eb/N0 value is obtained by adding the data rate gain to the Eb/N0
value of the parameter. The resulting Eb/N0 value is applied in producing the
service specific rate matching attributes.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
Parent parameter
EbNoOfPSConvSpe
Related features
Optimised push to talk experience (optional)
EbNoOfPSConvSpe/EbNoDCHOfPSConvSpeQua (Quality target of the PS conversational speech)
Description
The parameter defines the quality target for the PS conversational speech service.
The same quality target is used for both uplink and the downlink transfer directions.
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
Parent parameter
EbNoOfPSConvSpe
Related features
Optimised push to talk experience (optional)
EbNoOfPSConvSpe (Rate matching with the PS conversational speech services)
234
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Description
Summary of changes
The parameters of this structure define the quality targets of the PS conversational
speech service and the planned Eb/N0s of their DCHs.
An additional management parameter is introduced to assign a data rate gain
value for higher data rate services; the final Eb/N0 values are achieved by adding
the data rate gain to the quality target specific Eb/N0 values. The planned Eb/N0s
are applied in producing the service specific rate matching attributes.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
Child parameters
•
•
Related features
Optimised push to talk experience (optional)
EbNoDCHOfPSConvSpe
EbNoDCHOfPSConvSpeQua
SIRDPCCHInitialDCH/SIRDPCCHInitialDCHPSConvSpe (UL SIR target regardless of
DL channel - PS conv speech)
Description
This parameter defines the initial SIR target for the UL DPCCH when the radio link
has only DCHs configured in the uplink transfer direction for PS conversational
speech RB regardless of used DL channel. One-way receiver diversity is assumed.
Too low value causes too low success rate for first data packets. Too high
value causes UL power spiking
The parameter WCEL-EbNoSetIdentifier identifies the WRAB object set for
a cell.
To modify this parameter, you must manually lock and later unlock all WCEL
objects related to this WRAB. This will severely impact the network. You can avoid
it by creating a new WRAB and gradually transferring the WCELs to this one.
Parent parameter
SIRDPCCHInitialDCH
Related features
Optimised push to talk experience (optional)
WSMLC
CiPosCalcInSAS (Cell-ID based Position Calculation in SAS)
Description
This parameter enables and disables the feature PCAP Position Calculation procedure for Cell-ID Measurement Method.
Related features
LCS - Cell Coverage Based (RTT) with Geographical Coordinates (optional) AND
Point-to-Point Iu-pc Interface (optional) AND PCAP Position Calculation procedure
for Cell-ID Measurement Method (optional)
DN70456011
Id:0900d80580a2e11c
Confidential
235
Summary of changes
Radio Network Parameters in Flexi Direct
Changed parameters in Issue 06
ADJD
AdjdRTWithHSDPAHopsId (HSDPA HOPS identifier for speech services)
Field
Issue 05E
Issue 06
Parameter Name
HSDPA HOPS identifier for AMR multiservice
HSDPA HOPS identifier for speech
services
Description
The parameter identifies the parameter
set (HOPS object) which controls the
intra-frequency handover to the additional neighbour cell when a user has HSDSCH allocated simultaneously with the
AMR speech CS RAB.
The parameter identifies the parameter
set (HOPS object) which controls the
intra-frequency handover to the additional neighbour cell when a user has HSDSCH allocated simultaneously with the
AMR speech CS RAB or when the user
has push to talk allocated on HS-DSCH.
Related parameters
HOPSId of HOPS - Check that the
relevant HOPS object exists in the database.
HOPSId of HOPS - Check that the
relevant HOPS object exists in the database.
HSDPAenabled of WCEL - If AMR
service can be used with HS-DSCH and
HSDPA is enabled in the parent cell of
the additional intra-frequency neighbour
cell, the special value 'Not defined' is not
allowed for AdjdRTWithHSDPAHopsId.
HSDPAenabled of WCEL - If AMR
service can be used with HS-DSCH and
HSDPA is enabled in the parent cell of
the additional intra-frequency neighbour
cell, the special value 'Not defined' is not
allowed for AdjdRTWithHSDPAHopsId.
AMRWithHSDSCH of RNFC - If AMR
service can be used with HS-DSCH and
HSDPA is enabled in the parent cell of
the additional intra-frequency neighbour
cell, the special value 'Not defined' is not
allowed for AdjdRTWithHSDPAHopsId.
AMRWithHSDSCH of RNFC - If AMR
service can be used with HS-DSCH and
HSDPA is enabled in the parent cell of
the additional intra-frequency neighbour
cell, the special value 'Not defined' is not
allowed for AdjdRTWithHSDPAHopsId.
PTTEnabled of RNFC - If use of HSDPA
is enabled for PTT with the parameter
PTTEnabled (value > 1) and HSDPA is
enabled in the parent cell of the additional
intra-frequency neighbour cell, the
special value 'Not defined' is not allowed
for AdjdRTWithHSDPAHopsId.
Related features
Soft Handover Based on Detected Set
Reporting (optional) AND HSDPA
(optional)
Soft Handover Based on Detected Set
Reporting (optional) AND HSDPA
(optional)
AdjdRNCId (RNC Identifier)
236
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
An additional intra-frequency neighbour
cell is identified with the UTRAN Cell
Identifier, which is composed of the
Global RNC Identifier and the Cell Identifier. The Global RNC Identifier is
composed of the PLMN Identifier and the
RNC Identifier.
An additional intra-frequency neighbor
cell is identified with the UTRAN Cell
Identifier, which is composed of the
Global RNC Identifier and the Cell Identifier. The Global RNC Identifier is
composed of the PLMN Identifier and the
RNC Identifier.
For RAN 2054 feature "Extension of
RNC ids" only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
ADJG
ADJGBlindHO (ADJG Blind Handover to GSM/GPRS)
Field
Issue 05E
Issue 06
Description
The parameter indicates whether the IHSPA Adapter may perform an inter-RAT
handover to the GSM neighbour cell as a
blind handover.
The parameter indicates whether the FDRNC may perform an inter-RAT
handover to the GSM neighbour cell as a
blind handover.
Default value notes
I-HSPA Adapter can not perform an inter- FD-RNC can not perform an inter-RAT
RAT handover to the GSM neighbour cell handover to the GSM neighbour cell as a
as a blind handover.
blind handover.
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC
AdjgSIB (Include in System Information)
DN70456011
Id:0900d80580a2e11c
Confidential
237
Summary of changes
238
Radio Network Parameters in Flexi Direct
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
DN70456011
Summary of changes
Issue 05E
The parameter indicates whether the
GSM neighbour cell is included in the
System Information Block
11&11bis&12&18 for the cell selection
and re-selection procedures. The GSM
neighbour cell is included in the system
information when the value of the parameter is "SIB". The GSM neighbour cell is
included in the extended system information when the value of the parameter is
"SIBbis". The value of the parameter is
set by the system for the GAN neighbour
cell.
If the Wireless Priority Service feature
is enabled, then the parameter Include in
System Information shall be set to have
value "SIB" for ADJG-0.
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47. When HCS is used, the
capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
Note: The parameter AdjgSIB does
not affect GSM measurements in
CELL_DCH state of the connected mode.
That is, all GSM neighbour cells are monitored for the inter-system handover
regardless of the value of the parameter
AdjgSIB.
Issue 06
The parameter indicates whether the
GSM neighbour cell is included in the
System Information Block
11&11bis&12&18 for the cell selection
and re-selection procedures. The parameter also indicates whether the GSM
neighbour cell is monitored for the intersystem handover in CELL_DCH state of
connected mode. The GSM neighbour
cell is included in the system information
when the value of the parameter is "For
SIB and CELL DCH meas" or "For SIB
only". The GSM neighbour cell is
included in the extended system information when the value of the parameter is
"For SIBbis and CELL DCH meas" or
"For SIBbis only". The value of the
parameter is set by the system for the
GAN neighbour cell.
The GSM neighbour cell is monitored
for the inter-system handover regardless
of the value of the parameter AdjgSIB if
the value of the RNFC parameter FemtoHandoverControl is "Disabled". If the
value of the RNFC parameter FemtoHandoverControl is "Enabled":
- the GSM neighbour cell is monitored
for the inter-system handover if the value
of the parameter AdjgSIB is set to "For
CELL DCH meas only", "For SIB and
CELL DCH meas" or "For SIBbis and
CELL DCH meas".
- the GSM neighbour cell is not monitored for the inter-system handover if the
value of the parameter AdjgSIB is set to
"For SIB only" or "For SIBbis only".
If the Wireless Priority Service feature
is enabled, then the parameter Include in
System Information shall be set to have
value "For SIB and CELL DCH meas" for
ADJG-0.
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47 when all cell re-selection
parameters are broadcasted. When HCS
is used, the capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
Id:0900d80580a2e11c
239
support 3GPP R6.
Confidential
If the total number of intra-frequency,
inter-frequency and GSM neighbour
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Range and step
0 (No), 1 (SIB), 2 (SIBbis)
0 (For CELL DCH meas only), 1 (For SIB
and CELL DCH meas), 2 (For SIBbis and
CELL DCH meas), 3 (For SIB only), 4
(For SIBbis only)
Default value notes
The GSM neighbour cell is included in the
system information.
The GSM neighbour cell is included in the
system information and monitored for the
inter-system handover.
Related parameters
AdjiSIB of ADJI - Parameter indicates
whether the inter-frequency neighbour
cell is included in the System Information
for the cell selection and re-selection procedures.
AdjiSIB of ADJI - Parameter indicates
whether the inter-frequency neighbour
cell is included in the System Information
for the cell selection and re-selection procedures.
AdjsSIB of ADJS - Parameter indicates
whether the intra-frequency neighbour
cell is included in the system information
for the cell selection and re-selection procedures.
AdjsSIB of ADJS - Parameter indicates
whether the intra-frequency neighbour
cell is included in the system information
for the cell selection and re-selection procedures.
ADJGType of ADJG - Parameter value is
always "No" if the value of ADJGType is
"GAN cell".
ADJGType of ADJG - Parameter value is
always "No" if the value of ADJGType is
"GAN cell".
WireLessPriorityService of RNFC - If
Wireless Priority Service feature is
enabled, then AdjgSIB must be set with
the default value in ADJG-0 instance.
ADJI
BlindHOTargetCell (Blind HO target cell)
Field
Range and step
Issue 05E
0 (disabled), 1 (enabled)
Issue 06
0 (Disabled), 1 (Enabled)
AdjiCI (Cell Identifier)
Field
Description
Issue 05E
Issue 06
An inter-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
An inter-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier.
AdjiSIB (Include in System Information)
240
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
DN70456011
Summary of changes
Id:0900d80580a2e11c
Confidential
241
Summary of changes
Field
Description
242
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
This parameter indicates whether the
inter-frequency neighbour cell is included
in the System Information Block
11&12&18 for the cell selection and reselection procedures. The inter-frequency neighbour cell is included in the
system information when the value of the
parameter is "SIB". The inter-frequency
neighbour cell is included in the extended
system information when the value of the
parameter is "SIBbis".
The maximum number of inter-frequency neighbour cells that can be
included in the System Information Block
11&12&18 is 32. The neighbouring cells
can be distributed to up to two FDD
carriers (ref. 3GPP TS 25.133).
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47. When HCS is used, the
capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
Note: The parameter AdjiSIB does
not affect inter-frequency measurements
in CELL_DCH state of connected mode.
That is, all inter-frequency neighbour
cells are monitored for the inter-frequency handover regardless of the value
of the parameter AdjiSIB.
This parameter indicates whether the
inter-frequency neighbour cell is included
in the System Information Block
11&12&18 for the cell selection and reselection procedures. This parameter
also indicates whether the inter-frequency neighbour cell is monitored for
the inter-frequency handover in
CELL_DCH state of connected mode.
The inter-frequency neighbour cell is
included in the system information when
the value of the parameter is "For SIB
and CELL DCH meas" or "For SIB only".
The inter-frequency neighbour cell is
included in the extended system information when the value of the parameter is
"For SIBbis and CELL DCH meas" or
"For SIBbis only".
The inter-frequency neighbour cell is
monitored for the inter-frequency
handover regardless of the value of the
parameter AdjiSIB if the value of the
RNFC parameter FemtoHandoverControl is "Disabled". If the value of the RNFC
parameter FemtoHandoverControl is
"Enabled":
- the inter-frequency neighbour cell
is monitored for the inter-frequency
handover if the value of the parameter
AdjiSIB is set to "For CELL DCH meas
only", "For SIB and CELL DCH meas" or
"For SIBbis and CELL DCH meas".
- the inter-frequency neighbour cell
is not monitored for the inter-frequency
handover if the value of the parameter
AdjiSIB is set to "For SIB only" or "For
SIBbis only".
The maximum number of inter-frequency neighbour cells that can be
included in the System Information Block
11&12&18 is 32. The neighbouring cells
can be distributed to up to two FDD
carriers (ref. 3GPP TS 25.133).
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47 when all cell re-selection
parameters are broadcasted. When HCS
is used, the capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
DN70456011
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
Id:0900d80580a2e11c
Confidential
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Range and step
0 (No), 1 (SIB), 2 (SIBbis)
0 (For CELL DCH meas only), 1 (For SIB
and CELL DCH meas), 2 (For SIBbis and
CELL DCH meas), 3 (For SIB only), 4
(For SIBbis only)
Default value notes
The inter-frequency neighbour cell is
included in the SIB.
The inter-frequency neighbour cell is
included in the SIB and monitored for the
inter-frequency handover.
AdjiMCC (Mobile Country Code)
Field
Description
Issue 05E
Issue 06
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier which is
composed of Global RNC Identifier and
Cell Identifier. Furthermore, Global RNC
Identifier is composed of RNC Identifier
and PLMN Identifier, which in turn
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier which is
composed of Global RNC Identifier and
Cell Identifier. Furthermore, Global RNC
Identifier is composed of RNC Identifier
and PLMN Identifier, which in turn
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
AdjiMNC (Mobile Network Code)
Field
Description
Issue 05E
Issue 06
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier, which is
composed of Global RNC Identifier and
Cell Identifier. Furthermore, Global RNC
Identifier is composed of RNC Identifier
and PLMN Identifier, which in turn
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier, which is
composed of Global RNC Identifier and
Cell Identifier. Furthermore, Global RNC
Identifier is composed of RNC Identifier
and PLMN Identifier, which in turn
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
AdjiMNCLength (Mobile Network Code Length)
DN70456011
Id:0900d80580a2e11c
Confidential
243
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Description
Issue 05E
Issue 06
The parameter defines whether 2 or 3
digits are used in the Mobile Network
Code (MNC).
When this parameter is modified, also
the value of the MNC used by the system
is always changed.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
The parameter defines whether 2 or 3
digits are used in the Mobile Network
Code (MNC).
When this parameter is modified, also
the value of the MNC used by the system
is always changed.
AdjiRNCid (RNC Identifier)
Field
Description
Issue 05E
Issue 06
An inter-frequency neighbour cell is identified with UTRAN Cell Identifier, which is
composed of Global RNC Identifier and
Cell Identifier. Global RNC Identifier is
composed of PLMN Identifier and RNC
Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJI objects is required.
An inter-frequency neighbor cell is identified with UTRAN Cell Identifier, which is
composed of Global RNC Identifier and
Cell Identifier. Global RNC Identifier is
composed of PLMN Identifier and RNC
Identifier.
For RAN 2054 feature “Extension of
RNC ids “ only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
ADJL
AdjLEARFCN (E-UTRA Absolute Radio Frequency Channel Number)
Field
Issue 05E
Related parameters
Issue 06
SmartLTELayeringEnabled of WCEL The system prevents removal of the last
LTE neighbor if the Smart LTE Layering
feature is activated to the cell.
ADJS
AdjsCI (Cell Identifier)
244
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier.
RTWithHSDPAHopsIdentifier (HSDPA HOPS identifier for speechservices)
Field
Issue 05E
Issue 06
Parameter Name
HSDPA HOPS identifier for AMR multiservice
HSDPA HOPS identifier for speechservices
Description
This parameter identifies the parameter
set (HOPS object) controlling intra-frequency handovers of a user having HSDSCH allocated simultaneously with
AMR speech CS RAB.
This parameter identifies the parameter
set (HOPS object) controlling intra-frequency handovers of a user having HSDSCH allocated simultaneously with
AMR speech CS RAB or user having
push to talk allocated on HS-DSCH.
Related parameters
HOPSId of HOPS - Parameter must point
to the existing HOPSId.
HOPSId of HOPS - Parameter must point
to the existing HOPSId.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and Intra-Frequency
Adjacency (ADJS) parent HSDPAenabled are set to enabled, special value
'Not defined' is not allowed.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and Intra-Frequency
Adjacency (ADJS) parent HSDPAenabled are set to enabled, special value
'Not defined' is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and Intra-Frequency Adjacency (ADJS) parent
HSDPAenabled are set to enabled,
special value 'Not defined' is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and Intra-Frequency Adjacency (ADJS) parent
HSDPAenabled are set to enabled,
special value 'Not defined' is not allowed.
PTTEnabled of RNFC - If use of HSDPA
is enabled for PTT with the parameter
PTTEnabled (value > 1) and Intra-Frequency Adjacency (ADJS) parent HSDPAenabled are set to enabled, special
value 'Not defined' is not allowed.
Related features
HSDPA (optional) AND HSDPA with
HSDPA (optional) AND ( HSDPA with
Simultaneous AMR Voice Call (optional) Simultaneous AMR Voice Call (optional)
OR Optimised push to talk experience
(optional) )
AdjsSIB (Include in System Information)
DN70456011
Id:0900d80580a2e11c
Confidential
245
Summary of changes
246
Radio Network Parameters in Flexi Direct
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
DN70456011
Summary of changes
Issue 05E
The parameter determines whether the
intra-frequency neighbour cell is included
in the System Information Block
11&12&18 for the cell selection and reselection procedures. The intra-frequency neighbour cell is included in the
system information when the value of the
parameter is "SIB". The intra-frequency
neighbour cell is included in the extended
system information when the value of the
parameter is "SIBbis".
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47. When HCS is used, the
capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which are included in the System
Information, exceeds the physical size of
SIB data, the NBAP interface is not able
to pack the neighbour cell information
into the SIB data and the scheduling of
the system information blocks fails. The
cell is blocked by the system and an
alarm 7771 WCDMA CELL OUT OF USE
(BCCH scheduling error) is reported for
the cell.
Note: The parameter AdjsSIB does
not affect intra-frequency measurements
in CELL_DCH state of connected mode.
That is, all intra-frequency neighbour
cells are monitored for the soft(er)
handover regardless of the value of the
parameter AdjsSIB.
Issue 06
The parameter determines whether the
intra-frequency neighbour cell is included
in the System Information Block
11&12&18 for the cell selection and reselection procedures. The parameter
also determines whether the intra-frequency neighbour cell is monitored for
the soft(er) handover in CELL_DCH state
of connected mode. The intra-frequency
neighbour cell is included in the system
information when the value of the parameter is "For SIB and CELL DCH meas" or
"For SIB only". The intra-frequency
neighbour cell is included in the extended
system information (SIB11bis) when the
value of the parameter is "For SIBbis and
CELL DCH meas" or "For SIBbis only".
Information included in SIB11bis is not
included in SIB12. SIB12 contains the
cell information which is included in
SIB11.
The intra-frequency neighbour cell is
monitored for the soft(er) handover
regardless of the value of the parameter
AdjsSIB if the value of the RNFC parameter FemtoHandoverControl is "Disabled". If the value of the RNFC
parameter FemtoHandoverControl is
"Enabled":
- the intra-frequency neighbour cell
is monitored for the soft(er) handover if
the value of the parameter AdjsSIB is set
to "For CELL DCH meas only", "For SIB
and CELL DCH meas" or "For SIBbis and
CELL DCH meas".
- the intra-frequency neighbour cell
is not monitored for the soft(er) handover
if the value of the parameter AdjsSIB is
set to "For SIB only" or "For SIBbis only".
The total number of intra-frequency,
inter-frequency and GSM neighbour
cells, which can be included in the
System Information Block type 11
(SIB11), is 47 when all cell re-selection
parameters are broadcasted. When HCS
is used, the capacity is limited to 35 cells.
System Information Block type 11bis
(SIB11bis) increases the maximum
number of adjacencies to 96. SIB11bis
can only be decoded by the UEs which
support 3GPP R6.
If the total number of intra-frequency,
Id:0900d80580a2e11c
247
inter-frequency and GSM neighbour
Confidential
cells, which are included in the System
Information, exceeds the physical size of
Summary of changes
Field
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
Range and step
0 (No), 1 (SIB), 2 (SIBbis)
0 (For CELL DCH meas only), 1 (For SIB
and CELL DCH meas), 2 (For SIBbis and
CELL DCH meas), 3 (For SIB only), 4
(For SIBbis only)
Default value notes
The intra-frequency neighbour cell is
included in the System Information.
The intra-frequency neighbour cell is
included in the System Information and
monitored for the soft(er) handover.
AdjsMCC (Mobile Country Code)
Field
Description
Issue 05E
Issue 06
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. Furthermore, the Global RNC Identifier is
composed of the PLMN Identifier, which
consists of the Mobile Country Code
(MCC), the Mobile Network Code (MNC),
and the RNC Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. Furthermore, the Global RNC Identifier is
composed of the PLMN Identifier, which
consists of the Mobile Country Code
(MCC), the Mobile Network Code (MNC),
and the RNC Identifier.
AdjsMNC (Mobile Network Code)
Field
Description
Issue 05E
Issue 06
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. Furthermore, the Global RNC Identifier is
composed of the PLMN Identifier, which
consists of the Mobile Country Code
(MCC), the Mobile Network Code (MNC),
and the RNC Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. Furthermore, the Global RNC Identifier is
composed of the PLMN Identifier, which
consists of the Mobile Country Code
(MCC), the Mobile Network Code (MNC),
and the RNC Identifier.
AdjsMNCLength (Mobile Network Code Length)
248
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
The parameter defines whether 2 or 3
digits are used in the Mobile Network
Code (MNC).
When this parameter is modified also
the MNC value used by the system is
always changed.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
The parameter defines whether 2 or 3
digits are used in the Mobile Network
Code (MNC).
When this parameter is modified also
the MNC value used by the system is
always changed.
AdjsRNCid (RNC Identifier)
Field
Description
Issue 05E
Issue 06
An intra-frequency neighbour cell is identified with the UTRAN Cell Identifier,
which is composed of the Global RNC
Identifier and the Cell Identifier. The
Global RNC Identifier is composed of the
PLMN Identifier and the RNC Identifier.
The modification is not possible if the
new target cell is under the controlling
RNC. Cross-check between RNC, WCEL
and ADJS objects is required.
An intra-frequency neighbor cell is identified with the UTRAN Cell Identifier, which
is composed of the Global RNC Identifier
and the Cell Identifier. The Global RNC
Identifier is composed of the PLMN Identifier and the RNC Identifier.
For RAN 2054 feature "Extension of
RNC ids" only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
CBCI
CBCIPaddress (IP address of the CBC)
Field
Issue 05E
Issue 06
Description
CBC-IP address for the Cell Broadcast
Service. Each CBC can have a maximum
of four different CBC-IP addresses to
control Cell Broadcast Service.
Examples:
IPv4, 255.255.255.255, 1.1.1.1
IPv6,
FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FF
FF:FFFF
CBC-IP address for the Cell Broadcast
Service. Each CBC can have maximum
four different CBC-IP addresses to
control Cell Broadcast Service.
Examples:
IPv4, 255.255.255.255, 1.1.1.1
Range and step
7..39 characters
7..15 characters
Default value notes
The default value is not possible
Default value is not possible
Related features
Service Area Broadcast (optional)
Service Area Broadcast (optional) OR
SAB Support with 2 SCCPCHs (optional)
DN70456011
Id:0900d80580a2e11c
Confidential
249
Summary of changes
Radio Network Parameters in Flexi Direct
CBCIPaddrType (Type of CBC IP address)
Field
Issue 05E
Issue 06
Description
Indicates the used IP-address (Ipv4 or
Ipv6). Only one type of IP-address is
allowed to be used for one CBC.
Indicates the used IP-address (Ipv4).
Only one type of IP-address is allowed to
be used for one CBC.
Range and step
0 (IP v4), 1 (IP v6)
0 (IP v4)
Related features
Service Area Broadcast (optional)
Service Area Broadcast (optional) OR
SAB Support with 2 SCCPCHs (optional)
CMOB
TrafficRestriction (Traffic Restriction)
Field
Issue 05E
Range and step
0 (disabled), 1 (enabled)
Issue 06
0 (Disabled), 1 (Enabled)
FMCG
BLHOFailIRCellPenalty (BLHO failure inter-system cell penalty)
Field
Issue 05E
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC
HOPG
AdjgPriorityCoverage (Ncell Priority for Coverage HO)
Field
Description
Issue 05E
Issue 06
If there are several GSM neighbour cells
which meet the required radio link properties for the coverage (or quality) reason
handover at the same time, the RNC
ranks the potential target cells according
to priority levels and selects the highest
ranked GSM neighbour cell to be the
target cell.
The priority level of a GSM neighbour
cell is controlled by the parameter GSMncellPriorityCoverage. The range of the
parameter varies from zero to 7. Zero is
the lowest and 7 the highest priority level.
If there are several GSM neighbour cells
which meet the required radio link properties for the coverage (or quality) reason
handover at the same time, the RNC
ranks the potential target cells according
to priority levels and selects the highest
ranked GSM neighbour cell to be the
target cell.
The priority level of a GSM neighbour
cell is controlled by this parameter. The
range of the parameter varies from zero
to 7. Zero is the lowest and 7 the highest
priority level.
HOPI
AdjiHCSthreshold (Cell Re-selection HCS Threshold)
250
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
Defines the threshold level which must be
exceeded by the CPICH Ec/No of the
inter-frequency neighbour cell before the
hierarchical cell re-selection becomes
possible.
Defines the threshold level which must be
exceeded by the CPICH Ec/No or CPICH
RSCP of the inter-frequency neighbour
cell before the hierarchical cell re-selection becomes possible.
Please notice that if CPICH RSCP is
set as quality measure with the WCELCellSelQualMeas parameter then the
parameter value range -24 … 0 (step 0.5)
means RSCP values -115 dBm … -67
dBm (values 0…48 for RSCP in SIBs).
AdjiPriorityCoverage (Ncell Priority for Coverage IFHO)
Field
Description
Issue 05E
Issue 06
The inter-frequency measurement procedure measures one frequency at a time.
If there is more than one carrier frequency to be measured, the RNC selects
a subset of inter-frequency neighbour
cells (having the same UTRA RF channel
number) which are measured first.
In case of a coverage reason handover, the measurement order is controlled by the parameter
InterFreqNcellPriorityCoverage. The
range of the parameter varies from zero
to 7. Zero is the lowest and 7 the highest
priority level.
The inter-frequency measurement procedure measures one frequency at a time.
If there is more than one carrier frequency to be measured, the RNC selects
a subset of inter-frequency neighbour
cells (having the same UTRA RF channel
number) which are measured first.
In case of a coverage reason handover, the measurement order is controlled by this parameter. The range of
the parameter varies from zero to 7. Zero
is the lowest and 7 the highest priority
level.
AdjiPriorityQuality (Ncell Priority for Quality IFHO)
Field
Description
DN70456011
Issue 05E
Issue 06
The inter-frequency measurement procedure measures one frequency at a time.
If there is more than one carrier frequency to be measured, the RNC selects
a subset of inter-frequency neighbour
cells (having the same UTRA RF channel
number) which are measured first.
In case of a quality reason handover,
the measurement order is controlled by
the parameter InterFreqNcellPriorityQuality. The range of the parameter
varies from zero to 7. Zero is the lowest
and 7 the highest priority level.
The inter-frequency measurement procedure measures one frequency at a time.
If there is more than one carrier frequency to be measured, the RNC selects
a subset of inter-frequency neighbour
cells (having the same UTRA RF channel
number) which are measured first.
In case of a quality reason handover,
the measurement order is controlled by
this parameter. The range of the parameter varies from zero to 7. Zero is the
lowest and 7 the highest priority level.
Id:0900d80580a2e11c
Confidential
251
Summary of changes
Radio Network Parameters in Flexi Direct
HOPS
AdjsHCSthreshold (Cell Re-selection HCS Threshold)
Field
Description
Issue 05E
Issue 06
Defines the threshold level which must be
exceeded by the CPICH Ec/No of the
neighbouring cell before the hierarchical
cell re-selection becomes possible.
Defines the threshold level which must be
exceeded by the CPICH Ec/No or CPICH
RSCP of the neighbouring cell before the
hierarchical cell re-selection becomes
possible.
Please notice that if CPICH RSCP is
set as quality measure with the WCELCellSelQualMeas parameter then the
parameter value range -24 … 0 (step 0.5)
means RSCP values -115 dBm … -67
dBm (values 0…48 for RSCP in SIBs).
HSDPAAvailabilityIur (HSDPA availability of the neighbouring DRNC cell)
Field
Related parameters
Issue 05E
Issue 06
CSAMRModeSET of VCEL - HSDPA
availability check is valid if HSDPA over
Iur is enabled.
HSPAOverIur of IUR - HSDPA availability
check is valid if HSPA over Iur is enabled.
HSDPAenabled of VCEL - HSDPA availHSPAOverIur of IUR - HSDPA availability ability check is valid if HSDPA over Iur is
check is valid if HSPA over Iur is enabled. enabled.
IADA
CommonMCC (Common MCC)
Field
Description
252
Issue 05E
Issue 06
MCC (Mobile Country Code) part of
Common PLMN Id. Common PLMN Id is
used to represent all the operators in the
multi-operator core network. MCC
consists of three digits. MCC together
with MNC identifies the Common PLMN
id.
Common PLMN id (CommonMCC
and CommonMNC) should not be the
same as any PLMNid in RNC-IuOperator
CommonMCC is modifiable only
when there is no WCEL whose WCELPLMNid is exact same with CommonMCC/CommonMNC
If Common PLMN id is defined,
WCELCSCNId and WCELPSCNId
should not be configured
MCC (Mobile Country Code) part of
Common PLMN Id. Common PLMN Id is
used to represent all the operators in the
multi-operator core network. MCC
consists of three digits. MCC together
with MNC identifies the Common PLMN
id.
Common PLMN id must not be the
same as any primary or shared area
PLMNid in IUO instances.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
WCELCSCNId of WCEL - If Common
PLMN id is defined, WCELCSCNId and
WCELPSCNId should not be configured
WCELMCC of WCEL - This parameter is
modifiable only when there is no WCEL
whose PLMNid is exactly the same as
CommonMCC/CommonMNC.
WCELPLMNid of WCEL - This parameter
is modifiable only when there is no WCEL
whose WCELPLMNid is exactly the same
as CommonMCC/CommonMNC
WCELPSCNId of WCEL - If Common
PLMN id is defined, WCELCSCNId and
WCELPSCNId should not be configured
CommonMNC of IADA - MNC of
Common PLMN Id.
WCELMNC of WCEL - This parameter is
modifiable only when there is no WCEL
whose PLMNid is exactly the same as
CommonMCC/CommonMNC.
WCELMNCLength of WCEL - This
parameter is modifiable only when there
is no WCEL whose PLMNid is exactly the
same as CommonMCC/CommonMNC.
CommonMNC (Common MNC)
Field
Description
DN70456011
Issue 05E
Issue 06
This parameter defines MNC (Mobile
Network Code) part of Common PLMN
Id. Common PLMN Id is used to represent all the operators in the multioperator core network. MNC consists of
two or three digits. MNC together with
MCC identifies the Common PLMN Id.
Common PLMN Id (CommonMCC
and CommonMNC) cannot be the same
as any PLMNId in RNC-IuOperator.
CommonMNC is modifiable only
when there is no WCEL whose WCELPLMNId is exactly the same as CommonMCC/CommonMNC.
This parameter defines MNC (Mobile
Network Code) part of Common PLMN
Id. Common PLMN Id is used to represent all the operators in the multioperator core network. MNC consists of
two or three digits. MNC together with
MCC identifies the Common PLMN Id.
Common PLMN id must not be the
same as any primary or shared area
PLMNid in IUO instances.
Id:0900d80580a2e11c
Confidential
253
Summary of changes
Field
Related parameters
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
WCELCSCNId of WCEL - If Common
PLMN Id is defined, WCELCSCNId and
WCELPSCNId cannot be configured.
WCELMCC of WCEL - This parameter is
modifiable only when there is no WCEL
whose PLMNid is exactly the same as
CommonMCC/CommonMNC.
WCELPLMNid of WCEL - This parameter
is modifiable only when there is no WCEL
whose WCELPLMNId is exactly the
same as CommonMCC/CommonMNC.
WCELPSCNId of WCEL - If Common
PLMN Id is defined, WCELCSCNId and
WCELPSCNId cannot be configured.
CommonMCC of IADA - MCC of
Common PLMN Id.
WCELMNC of WCEL - This parameter is
modifiable only when there is no WCEL
whose PLMNid is exactly the same as
CommonMCC/CommonMNC.
WCELMNCLength of WCEL - This
parameter is modifiable only when there
is no WCEL whose PLMNid is exactly the
same as CommonMCC/CommonMNC.
CommonMNCLength of IADA - MNC
length of Common PLMN Id. Value range
depends on the MNCLength: 00...99 (if
MNCLength is 2) or 000...999 (if MNCLength is 3). If the related parameter
CommonMNCLenth has a default value
of "not defined", then the only allowed
value for the CommonMNC is the default
value "not defined".
ExtendedULDLactivationTmr (Extended Cell_FACH inactivity supervision timer)
Field
Issue 05E
Issue 06
Description
This parameter defines an extended
Cell_FACH state inactivity supervision
time used by the RNC instead of the
normal UL_DL_Activation_Timer. If set to
a value greater than zero, this value is
used for all UEs not supporting the
Cell/URA_PCH state.
This parameter defines an extended
Cell_FACH state inactivity supervision
time used by the RNC instead of the
normal UL_DL_Activation_Timer. If set to
a value greater than zero, this value is
used for all UEs not supporting the
Cell/URA_PCH state. Otherwise, normal
WAC-UL_DL_Activation_Timer is used
for all UEs not supporting
Cell/URA_PCH.
Related parameters
UL_DL_activation_timer of IADA - If
ExtendedULDLactivationTmr = 0, normal
UL_DL_Activation_Timer is used for all
UEs and no extended time for UEs not
supporting Cell/URA_PCH is used.
IASCCRepTimer (Inter-Adapter SCC repetition timer)
Field
Interfaces
254
Issue 05E
RAC<->IADA, EM<->IADA, RACApp<>RAC
Id:0900d80580a2e11c
Confidential
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
LCSfunctionality (LCS functionality)
Field
Issue 05E
Related parameters
Issue 06
LCSSupportForAnchoring of IADA - LCS
Support in Drift RNC feature can be
enabled only if LCS functionality is
enabled.
ConnectionRetryCounter (OAM Connection Establishment Retry Counter)
Field
Issue 05E
Issue 06
Range and step
1..20, step 1
1..30, step 1
Default value
10
15
SIB11_priority (Priority for SIB11)
Field
Issue 05E
Issue 06
Description
The priority of the System Information
Block 11, which is used by the scheduling
algorithm in the RNC to give precedence
to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 11 priority
shall have higher priority value than SIB
1, SIB2, SIB3, SIB5 and SIB7.
System Information Block type 11bis
(SIB11bis) provides extension segments
for SIB11. The value of the SIB11_priority
is used also for SIB11bis.
The priority of the System Information
Block 11, which is used by the scheduling
algorithm in the RNC to give precedence
to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 11 shall
have lower priority than SIB 1, SIB2,
SIB3, and SIB5. The value of the
SIB11_priority is used also for SIB11bis.
Related parameters
SIB18_priority of IADA - The priority of
SIB11 shall not be lower than what is
defined for SIB18.
SIB18_priority of IADA - The priority of
SIB11 shall not be lower than what is
defined for SIB18.
SIB15_priority (Priority for SIB15)
Field
Description
Issue 05E
Issue 06
The parameter defines the priority of the
System Information Block 15, which is
used by the scheduling algorithm in the
RNC to give precedence to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 15 priority
shall have higher priority value than SIB
1, SIB2, SIB3, SIB5 and SIB7.
The parameter defines the priority of the
System Information Block 15, which is
used by the scheduling algorithm in the
RNC to give precedence to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 15 priority
shall have lower than SIB 1, SIB2, SIB3,
and SIB5.
SIB18_priority (Priority for SIB18)
DN70456011
Id:0900d80580a2e11c
Confidential
255
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
The priority of the System Information
Block 18, which is used by the scheduling
algorithm in the RNC to give precedence
to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 18 priority
shall have higher priority value than SIB
1, SIB2, SIB3, SIB5 and SIB7.
The priority of the System Information
Block 18, which is used by the scheduling
algorithm in the RNC to give precedence
to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 18 priority
shall have lower than SIB 1, SIB2, SIB3,
and SIB5.
Related parameters
SIB11_priority of IADA - The priority of
SIB18 shall not be higher than what is
defined for SIB11
SIB11_priority of IADA - The priority of
SIB18 shall not be higher than what is
defined for SIB11
SIB12_priority of IADA - The priority of
SIB18 shall not be higher than what is
defined for SIB12
SIB19Priority (Priority for SIB19)
Field
Issue 05E
Issue 06
Description
This parameter defines the priority of the
System Information Block 19, which is
used by the scheduling algorithm in the
RNC to give precedence to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 19 priority
shall have higher priority value than SIB
1, SIB2, SIB3, SIB5 and SIB7.
This parameter defines the priority of the
System Information Block 19, which is
used by the scheduling algorithm in the
RNC to give precedence to the SIB.
1 = highest priority
4 = lowest priority
System Information Block 19 priority
shall have lower than SIB 1, SIB2, SIB3,
and SIB5.
Default value
3
4
SIB3_priority (Priority for SIB3)
Field
Interfaces
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC<->UE
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC
PageRep1stInterv (Repetition interval of the first repeated connected mode paging procedure)
Field
Default value
256
Issue 05E
700
Issue 06
1100
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Default value notes
Summary of changes
Issue 05E
Issue 06
DRX Cycle length 640ms assumed. The
first paging repetition should be executed
as soon as possible to emphasize the
response-time for all those mobiles which
have not received the actual paging
message. This will, however, cause the
first repeated paging executed also for a
certain amount of the mobiles that
actually have received the 1st paging, but
there has not been enough time to send
the paging response to the RNC. In
RAN2 it is assumed that the paging load
is not the limiting factor.
DRX Cycle length 640ms assumed. The
first paging repetition should be executed
as soon as possible to emphasize the
response-time for all those mobiles which
have not received the actual paging
message. This will, however, cause the
first repeated paging executed also for a
certain amount of the mobiles that
actually have received the 1st paging, but
there has not been enough time to send
the paging response to the RNC.
RestrictionInterval (Restriction Interval)
Field
Issue 05E
Issue 06
Description
Length of traffic restriction period in RNC
when 'Radio Network Access Regulation
Function' or 'Domain Specific Access
Class Restriction' is active in RNC. RNC
sets timer using parameter value. During
traffic restriction period user defined
amount of Access Classes are prevented
from accessing the network. When timer
set with this parameter value expires new
set of Access Classes are selected to be
'barred' and timer is set again. The
amount of Access Classes to be barred
simultaneously is defined with parameter
CellAccessRestriction.
Length of traffic restriction period in RNC
when 'Radio Network Access Regulation
Function' or 'Domain Specific Access
Class Restriction' or ‘Automatic Access
Class Restriction’ is active in RNC. RNC
sets timer using parameter value. During
traffic restriction period user defined
amount of Access Classes are prevented
from accessing the network. When timer
set with this parameter value expires new
set of Access Classes are selected to be
'barred' and timer is set again. The
amount of Access Classes to be barred
simultaneously is defined with parameter
CMOB -CellAccessRestriction. In case of
the Automatic Access Restriction, the
number of the restricted access classes
is automatically increased or decreased
according to the overload conditions.
Related parameters
ACBarredListSystem of CMOB - When
Access Classes to be barred have been
selected, ACBarredListSystem is
updated to show the barring situation.
ACBarredListSystem of CMOB - When
Access Classes to be barred have been
selected, ACBarredListSystem is
updated to show the barring situation.
CellAccessRestriction of CMOB - 'CellAccessRestriction' indicates how many
Access Classes will be barred (out of
Access Classes 0 to 9).
CellAccessRestriction of CMOB - 'CellAccessRestriction' indicates how many
Access Classes will be barred (out of
Access Classes 0 to 9).
RNARDSACGuardTime of RNAC RNARDSACGuardTime shall be smaller
than RestrictionInterval.
DN70456011
Id:0900d80580a2e11c
Confidential
257
Summary of changes
Field
Related features
Radio Network Parameters in Flexi Direct
Issue 05E
Radio Network Access Regulation
Function (optional)
Issue 06
Radio Network Access Regulation
Function (optional) OR Automatic
access class restriction (optional)
ServingOMS (Serving OMS )
Field
Related parameters
Issue 05E
Issue 06
OMSIpAddress of IADA - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS. When
ServingOMS parameter is set to 1 (primary), then OMSIpAddress value 0.0.0.0
is not allowed.
OMSIpAddress of IADA - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS. When
ServingOMS parameter is set to 1 (primary), then OMSIpAddress value 0.0.0.0
is not allowed.
SecOMSIpAddress of IADA - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC. When ServingOMS parameter is set to 2 (secondary),
then SecOMSIpAddress default value
(0.0.0.0) is not allowed.
SecOMSIpAddress of IADA - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC. When ServingOMS parameter is set to 2 (secondary),
then SecOMSIpAddress default value
(0.0.0.0) is not allowed.
ServingOMSSwoRequest of IADA Serving OMS Switchover Request is
used to trigger the OMS switchover procedure in RNC/ADA.
ServingOMSSwoRequest of IADA Serving OMS Switchover Request is
used to trigger the OMS switchover procedure in RNC.
ServingOMSAdminSetting of IADA Serving OMS Admin Setting specifies if
the automatic OMS switchover is in use
or if RNC/ADA is forced to connect to the
specific IP address.
ServingOMSAdminSetting of IADA Serving OMS Admin Setting specifies if
the automatic OMS switchover is in use
or if RNC is forced to connect to the
specific IP address.
ServingOMSAdminSetting (Serving OMS Admin Setting)
Field
Description
258
Issue 05E
Issue 06
This parameter specifies if the automatic
OMS switchover is in use or if RNC/ADA
is forced to connect to the specific IP
address.
This parameter specifies if the automatic
OMS switchover is in use or if RNC is
forced to connect to the specific IP
address.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
OMSIpAddress of IADA - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS. The
Serving OMS Admin Setting parameter
can force the NE to use the primary OMS
IP Address for the active O&M connection.
OMSIpAddress of IADA - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS. The
Serving OMS Admin Setting parameter
can force the NE to use the primary OMS
IP Address for the active O&M connection.
SecOMSIpAddress of IADA - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC. When ServingOMSAdminSetting parameter is set to 2
(secondary forced), then SecOMSIpAddress parameter should not contain
default value (0.0.0.0).
SecOMSIpAddress of IADA - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC. When ServingOMSAdminSetting parameter is set to 2
(secondary forced), then SecOMSIpAddress parameter should not contain
default value (0.0.0.0).
ServingOMSSwoRequest of IADA Serving OMS Switchover Request
parameter is used to trigger the OMS switchover procedure in RNC/ADA. Serving
OMS Admin Setting should have value
"automatic" to enable the operator controlled OMS switchover. The switchover
can be started with parameter Serving
OMS Switchover Request.
ServingOMSSwoRequest of IADA Serving OMS Switchover Request
parameter is used to trigger the OMS switchover procedure in RNC. Serving OMS
Admin Setting should have value "automatic" to enable the operator controlled
OMS switchover. The switchover can be
started with parameter Serving OMS Switchover Request.
ServingOMSSwoRequest (Serving OMS Switchover Request)
Field
Description
DN70456011
Issue 05E
Issue 06
This parameter is a trigger for the OMS
switchover procedure in RNC/ADA.
Note that a successful parameter
change does not yet guarantee a successful OMS switchover, which depends
on several other factors. Check that
alarm 2081 "OMS SWITCHOVER HAS
BEEN PERFORMED" is visible after switchover is requested. The alarm indicates
that the OMS switchover is done successfully.
The value of the parameter is not
stored as such in RNC/ADA. It is just
used for triggering the OMS switchover.
Thus the parameter does not have any
value that is used for describing the situation in the network.
This parameter is a trigger for the OMS
switchover procedure in RNC.
Note that a successful parameter
change does not yet guarantee successful OMS switchover, which depends on
several other factors. Check that alarm
0821 "OMS SWITCHOVER HAS BEEN
PERFORMED" is visible after switchover
is requested. The alarm indicates that the
OMS switchover is done successfully.
The value of the parameter is not
stored as such in RNC. It is just used for
triggering the OMS switchover. Thus the
parameter does not have any value that
is used for describing the situation in the
network.
Id:0900d80580a2e11c
Confidential
259
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Related parameters
Issue 06
OMSIpAddress of IADA - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS.
OMSIpAddress of IADA - OMS IP
Address specifies the primary OMS IP
address that is needed to establish
TCP/IP connections to the OMS.
SecOMSIpAddress of IADA - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC.
SecOMSIpAddress of IADA - Secondary
OMS IP address specifies the secondary
OMS IP address in RNC.
ServingOMSAdminSetting of IADA Serving OMS Admin Setting specifies if
the automatic OMS switchover is in use
or if RNC/ADA is forced to connect to the
specific IP address. The requested OMS
switchover is possible only when Serving
OMS Admin Setting has the value "automatic".
ServingOMSAdminSetting of IADA Serving OMS Admin Setting specifies if
the automatic OMS switchover is in use
or if RNC is forced to connect to the
specific IP address. The requested OMS
switchover is possible only when Serving
OMS Admin Setting has the value "automatic".
IPNB
NodeBIPAddress (Control Plane Destination Address Iub)
Field
Description
Issue 05E
Issue 06
This parameter defines the destination IP
address for the control plane and user
plane connections at the I-BTS internal
Iub interface.
Changing the default value
192.168.10.10 is not recommended. The
only reason for changing it is that I-BTS
internal /24 subnet is already being used
in transport network. In such a case the
following IP address is recommended:
192.168.255.98.
This parameter defines the destination IP
address for the control plane and user
plane connections at the FD-BTS internal
Iub interface.
Changing the default value
192.168.10.10 is not recommended. The
only reason for changing it is that FDBTS internal /24 subnet is already being
used in transport network. In such a case
the following IP address is recommended: 192.168.255.98.
SourceNBAPIPAddress (Iub control plane source IP address)
260
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
Iub control plane source IP address
together with the SourceNBAPIPNetmask is applied for selecting the Iub
control plane recovery group for terminating the services. The subnet definition is
applied in the creation of the Iub control
plane NBAP/SCTP connections. After
the resources are created the recovery
group remains the same until the given
Iub control plane resources are removed
from the system by deleting the IPNB or
by removing the IPNB reference from the
WBTS object. The subnet definition limits
the group of IP address candidates
where the Iub control plane application
services are terminated.
Note: The IP addresses have to be
assigned into the Iub control plane
recovery group before starting to create
the Iub control plane resources.
Single recovery group in the selection:
- 10.20.30.40 / 32 points to a given
IP address 10.20.30.40 which is related
to a certain Iub control plane recovery
group
Several recovery groups in the selection:
- 10.20.30.40 / 24 for example points
to a IP addresses belonging to the given
subnet (10.20.30.0 – 10.20.30.255).
System selects the one of the Iub control
plane recovery groups that have
matching IP address configured.
Iub control plane source IP address
together with the SourceNBAPIPNetmask is applied for selecting the Iub
control plane recovery group for terminating the services. The subnet definition is
applied in the creation of the Iub control
plane NBAP/SCTP connections. After
the resources are created the recovery
group remains the same until the given
Iub control plane resources are removed
from the system by deleting the IPNB or
by removing the IPNB reference from the
WBTS object. The subnet definition limits
the group of IP address candidates
where the Iub control plane application
services are terminated.
Note: The IP addresses have to be
assigned into the Iub control plane
recovery group before starting to create
the Iub control plane resources.
Single recovery group in the selection:
- 10.20.30.40 / 32 points to a given
IP address 10.20.30.40 which is related
to a certain Iub control plane recovery
group.
Several recovery groups in the selection:
- 10.20.30.40 / 24 for example points
to a IP addresses belonging to the given
subnet (10.20.30.0 – 10.20.30.255).
System selects the one of the Iub control
plane recovery groups that have
matching IP address configured.
Modification
unmodifiable
objectLocking
Related features
IP Based Iub for Flexi WCDMA BTS
(optional), IP Based Iub for UltraSite
WCDMA BTS (optional)
IP Based Iub for Flexi WCDMA BTS
(optional)
SourceNBAPIPNetmask (Iub control plane source IP netmask)
DN70456011
Id:0900d80580a2e11c
Confidential
261
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
Iub control plane source IP netmask
together with the SourceNBAPIPAddress
is applied for selecting the Iub control
plane recovery group for terminating the
services. The subnet definition is applied
in the creation of the Iub control plane
NBAP/SCTP connections. After the
resources are created the recovery group
remains the same until the given Iub
control plane resources are removed
from the system by deleting the IPNB or
by removing the IPNB reference from the
WBTS object. The subnet definition limits
the group of IP address candidates
where the Iub control plane application
services are terminated.
Note: The IP addresses have to be
assigned into the Iub control plane
recovery group before starting to create
the Iub control plane resources.
Single recovery group in the selection:
- 10.20.30.40 / 32 points to a given
IP address 10.20.30.40 which is related
to a certain Iub control plane recovery
group
Several recovery groups in the selection:
- 10.20.30.40 / 24 for example points
to a IP addresses belonging to the given
subnet (10.20.30.0 – 10.20.30.255).
System selects the one of the Iub control
plane recovery groups that have
matching IP address configured.
Iub control plane source IP netmask
together with the SourceNBAPIPAddress
is applied for selecting the Iub control
plane recovery group for terminating the
services. The subnet definition is applied
in the creation of the Iub control plane
NBAP/SCTP connections. After the
resources are created the recovery group
remains the same until the given Iub
control plane resources are removed
from the system by deleting the IPNB or
by removing the IPNB reference from the
WBTS object. The subnet definition limits
the group of IP address candidates
where the Iub control plane application
services are terminated.
Note: The IP addresses have to be
assigned into the Iub control plane
recovery group before starting to create
the Iub control plane resources.
Single recovery group in the selection:
- 10.20.30.40 / 32 points to a given
IP address 10.20.30.40 which is related
to a certain Iub control plane recovery
group.
Several recovery groups in the selection:
- 10.20.30.40 / 24 for example points
to a IP addresses belonging to the given
subnet (10.20.30.0 – 10.20.30.255).
System selects the one of the Iub control
plane recovery groups that have
matching IP address configured.
Modification
onLine
objectLocking
IPQM
BackgroundTCToDSCP (Background TC to DSCP mapping)
Field
Related features
Issue 05E
Issue 06
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
IPQMChangeOrigin (Change origin)
262
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related features
Summary of changes
Issue 05E
Issue 06
IP based Iu-CS (optional) OR IP based
Iu-PS (optional)
ConversationalTCToDSCP (Conversational TC to DSCP mapping)
Field
Related features
Issue 05E
Issue 06
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
InteractiveTHP1TCToDSCP (Interactive THP1 TC to DSCP mapping)
Field
Related features
Issue 05E
Issue 06
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
InteractiveTHP2TCToDSCP (Interactive THP2 TC to DSCP mapping)
Field
Related features
Issue 05E
Issue 06
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
InteractiveTHP3TCToDSCP (Interactive THP3 TC to DSCP mapping)
Field
Related features
Issue 05E
Issue 06
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
IPQMId (IP Qos Management Identifier)
Field
Issue 05E
Related parameters
Issue 06
IPQMIdCS of IUCSIP - The IPQM object
cannot be deleted in case IUCSIP object
refers to it.
IPQMIdPS of IUPSIP - The IPQM object
cannot be deleted in case IUPSIP object
refers to it.
Related features
DN70456011
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
Id:0900d80580a2e11c
Confidential
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
263
Summary of changes
Radio Network Parameters in Flexi Direct
StreamingTCToDSCP (Streaming TC to DSCP mapping)
Field
Related features
Issue 05E
Issue 06
IP based Iu-PS (optional) OR IP based
Iu-CS (optional)
IP based Iu-PS (optional) OR IP based
Iu-CS (optional) OR Basic functions
(standard)
IUCS
NetworkInd (Network indicator)
Field
Issue 05E
Related parameters
Issue 06
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
CNDomainVersion (Release version of Core Network)
Field
Range and step
Issue 05E
1 (R99), 2 (Rel4), 3 (Rel5), 4 (Rel6), 5
(Rel7), 6 (Rel8), 7 (Rel9)
Issue 06
1 (R99), 2 (Rel4), 3 (Rel5), 4 (Rel6), 5
(Rel7), 6 (Rel8), 7 (Rel9), 8 (Rel10), 9
(Rel11), 10 (Rel12)
SignPointCode (Signalling point code)
264
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
The code that uniquely identifies the signalling point in the signalling network.
The parameter is not modifiable if the
core network is active. Parameter modification terminates ongoing calls.
The code identifies the signalling point in
the signalling network.
Combination of NetworkInd and SignPointCode uniquely identifies a Signalling Point.
The parameter is not modifiable if the
core network is active. Parameter modification terminates ongoing calls.
Related parameters
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
PagingOptSupport (Support of Paging Optimization Feature)
Field
Issue 05E
Issue 06
Description
This parameter controls whether Paging
Optimization Feature is used for this IU
interface or not. If enabled then for
pagings received on this interface, I-BTS
will distribute the paging message among
paging group members.
This parameter controls whether Paging
Optimization Feature is used for this IU
interface or not. If enabled then for
pagings received on this interface, FDBTS will distribute the paging message
among paging group members.
Range and step
0 (disabled), 1 (enabled)
0 (Disabled), 1 (Enabled)
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC
IUCSIP
DestIPAddressCS (IP address for the IUCS destination subnet)
DN70456011
Id:0900d80580a2e11c
Confidential
265
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
The DestIPAddressCS attribute with the
IPNetmaskCS parameter forms a destination IP subnet definition for the Iu-CS
user plane connections. The RNC
performs the IP Based Route id reference
selection for the new Iu-CS connection in
between the destination IP subnet and
the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUCSIP
object instance needed under the IUCS
object instance. Example IPv4: 0.0.0.0 / 0
-> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUCSIP objects under the IUCS.
Example IPv4: IUCSIP#1 192.168.0.0 /
28 -> IP Based Route id y, IUCSIP#2
192.168.0.16 / 28 -> IP Based Route id z.
This parameter is used with IP over
Ethernet Iu-CS connectivity in cRNC and
mcRNC. In case of I-HSPA the parameter is always used for the Iu-CS connectivity.
The DestIPAddressCS attribute with the
IPNetmaskCS parameter forms a destination IP subnet definition for the Iu-CS
user plane connections. The RNC
performs the IP Based Route id reference
selection for the new Iu-CS connection in
between the destination IP subnet and
the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUCSIP
object instance needed under the IUCS
object instance. Example IPv4: 0.0.0.0 / 0
-> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUCSIP objects under the IUCS.
Example IPv4: IUCSIP#1 192.168.0.0 /
28 -> IP Based Route id y, IUCSIP#2
192.168.0.16 / 28 -> IP Based Route id z.
This parameter is used with IP over
Ethernet Iu-CS connectivity in cRNC and
mcRNC. In case of Flexi Direct RNC the
parameter is always used for the Iu-CS
connectivity.
Default value
-
0.0.0.0
Default value notes
Related parameters
Referred IP Based Route gets selected
regardless of the IP address signaled by
the CN.
IPNetmaskCS of IUCSIP - The IPNetmaskCS with the DestIPAddressCS attribute form the destination IP subnet
definition.
IPNetmaskCS of IUCSIP - The IPNetmaskCS together with the DestIPAddressCS attribute form the destination IP
subnet which must be unique for each
IUCSIP object.
IPBasedRouteIdCS (IP Based Route Identifier for IUCS)
266
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
The IPBasedRouteId refers to the logical
IP Based Route entity configured in the
IP layer with MML or through the IP Plan
interface. The IP Based Route configured
for the Iu-CS interface is used for the user
plane connections towards the Iu-CS CN
element controlling the interface unit and
port selection along with the source IP
address and the UDP port selection. This
parameter is applied when the IP over
Ethernet transport option is used.
The IPBasedRouteId refers to the logical
IP Based Route entity configured in the
IP layer with MML/SCLI or through the IP
Plan interface. The IP Based Route configured for the Iu-CS interface is used for
the user plane connections towards the
Iu-CS CN element controlling the interface unit and port selection along with the
source IP address and the UDP port
selection. This parameter is applied when
the IP over Ethernet transport option is
used.
Default value
0
Default value notes
Value not defined.
Special value
0
IPNetmaskCS (IP netmask for the IUCS destination subnet)
DN70456011
Id:0900d80580a2e11c
Confidential
267
Summary of changes
Field
Description
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
The IPNetmaskCS with the DestIPAddressCS attribute forms a destination IP
subnet definition for the Iu-CS user plane
connections. The RNC performs the IP
Based Route id reference selection for
the new Iu-CS connection in between the
destination IP subnet and the destination
IP address (RANAP:Transport Layer
Address) that is received at the RAB
assignment request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUCSIP
object instance needed under the IUCS
object instance. Example IPv4: 0.0.0.0 /
0.0.0.0 -> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUCSIP objects under the IUCS.
Example IPv4: IUCSIP#1 192.168.0.0 /
255.255.255.240 -> IP Based Route id y,
IUCSIP#2 192.168.0.16 /
255.255.255.240 -> IP Based Route id z.
This parameter is used with IP over
Ethernet Iu-CS connectivity in cRNC and
mcRNC. In case of I-HSPA the parameter is always used for the Iu-CS connectivity.
The IPNetmaskCS with the DestIPAddressCS attribute forms a destination IP
subnet definition for the Iu-CS user plane
connections. The RNC performs the IP
Based Route id reference selection for
the new Iu-CS connection in between the
destination IP subnet and the destination
IP address (RANAP:Transport Layer
Address) that is received at the RAB
assignment request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUCSIP
object instance needed under the IUCS
object instance. Example IPv4: 0.0.0.0 /
0.0.0.0 -> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUCSIP objects under the IUCS.
Example IPv4: IUCSIP#1 192.168.0.0 /
255.255.255.240 -> IP Based Route id y,
IUCSIP#2 192.168.0.16 /
255.255.255.240 -> IP Based Route id z.
This parameter is used with IP over
Ethernet Iu-CS connectivity in cRNC and
mcRNC. In case of Flexi Direct RNC the
parameter is always used for the Iu-CS
connectivity.
Default value notes
Related parameters
Referred IP Based Route gets selected
regardless of the IP address signaled by
the CN
DestIPAddressCS of IUCSIP - The
IPNetmaskCS with the DestIPAddressCS attribute form the destination IP
subnet definition.
DestIPAddressCS of IUCSIP - The
IPNetmaskCS together with the DestIPAddressCS attribute form the destination IP subnet which must be unique for
each IUCSIP object.
IPQMIdCS (IPQM object id for IuCS)
268
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Parameter Name
IPQM object id for IuItemCS
IPQM object id for IuCS
Description
The IPQM identification gives the reference to the IPQM object used for the CS
CN. The IPQM object defines the UMTS
traffic class to DSCP mapping to be used
for the IP connections at the Iu interface.
IPQM reference needs to be given in the
CN definitions if the IP transport is used
at the interface towards the corresponding CN element.
This parameter is used only with CN
nodes that use the IP over Ethernet as
transmission technology.
The IPQM identification gives the reference to the IPQM object used for the CS
CN. The IPQM object defines the UMTS
traffic class to DSCP mapping to be used
for the IP connections at the Iu interface.
IPQM reference needs to be given in the
CN definitions if the IP transport is used
at the interface towards the corresponding CN element. The referred IPQM
instance has to exist in the system before
IUCSIP is created.
This parameter is used only with CN
nodes that use the IP over Ethernet as
transmission technology.
Range and step
0..8, step 1
1..8, step 1
Default value
0
Default value notes
0 means that the IPQM reference is not
given and default values are used.
Related parameters
IPQMId of IPQM - The IPQM object
instance referred by IPQMIdCS has to
exist.
IUO
PLMNid/MCC (Mobile Country Code)
Field
Issue 05E
Description
Unique country identification. MCC
consists of three digits. MCC together
with MNC identifies the PLMN uniquely
(globally).
Default value
65535
Default value notes
Not defined
Special value
65535
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Issue 06
Unique country identification. MCC
consists of three digits. MCC together
with MNC identifies the PLMN uniquely
(globally).
MCC cannot be modified in case
it is mapped to any WCEL or CBCI
PLMNid/MNC (Mobile Network Code)
DN70456011
Id:0900d80580a2e11c
Confidential
269
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
Unique network identification within
country. MNC consists of two or three
digits. MNC together with MCC identifies
the PLMN uniquely (globally).
Unique network identification within
country. MNC consists of two or three
digits. MNC together with MCC identifies
the PLMN uniquely (globally).
MNC cannot be modified in case
it is mapped to any WCEL or CBCI
Default value
65535
Default value notes
Not defined
Special value
65535
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
PLMNid/MNCLength (Mobile Network Code Length)
Field
Issue 05E
Issue 06
Description
This parameter defines whether 2 or 3
digits are used in Mobile Network Code.
When this parameter is modified
also the value of MNC used by system is
always changed.
This parameter defines whether 2 or 3
digits are used in Mobile Network Code.
This parameter cannot be modified
in case IUO-PLMNid is mapped to any
WCEL or CBCI.
When this parameter is modified
also the value of MNC used by system is
always changed.
Default value
2
Interfaces
RAC<->RNC, EM<->RNC
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
RAC<->RNC, EM<->RNC, RAC<>RACApp
NRILengthForCSCN (NRI length for CS Core Networks)
Field
Description
Issue 05E
Issue 06
This parameter defines the length (in bits)
of the NRI parameter to be used in the CS
CN selection.
This parameter defines the length (in bits)
of the NRI parameter to be used in the CS
CN selection.
Note that this parameter is visible
only when CS licenses of IuFlex and/or
Multi-Operator Core Network is/are activated. When none of the licenses is activated, the parameter value is handled as
0 in L3 SW.
270
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related features
Summary of changes
Issue 05E
Issue 06
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
NRILengthForPSCN (NRI length for PS Core Networks)
Field
Description
Issue 05E
Issue 06
This parameter defines the length (in bits)
of the NRI parameter to be used in the PS
CN selection.
This parameter defines the length (in bits)
of the NRI parameter to be used in the PS
CN selection.
IuOperator => NRILengthForPSCN
Note that this parameter is visible
only when PS licenses of IuFlex and/or
Multi-Operator Core Network is/are activated. When none of the licenses is activated, the parameter value is handled as
0 in L3 SW.
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
NullNRIForCSPool (Null NRI value for CS Pool)
Field
Description
Issue 05E
Issue 06
This parameter defines the MSC allocated NRI value to be used in load redistribution. The RNC's NAS node selection
function uses load balancing in routing for
all the UEs using Null NRI.
This parameter defines the operator Null
NRI value for CS domain to select a
certain operator in a Multi Operator Core
Network.
NOTE: All operators must have theirspecific Null NRI.
NOTE: Null NRI value cannot be
given to any MSC of the pool.
NOTE: Operator cannot have same
null-NRI as others.
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Multi-Operator Core Network (optional)
NullNRIForPSPool (Null NRI value for PS Pool)
DN70456011
Id:0900d80580a2e11c
Confidential
271
Summary of changes
Field
Description
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
This parameter defines the SGSN allocated NRI value to be used in load redistribution. The RNC's NAS node selection
function uses load balancing in routing for
all the UEs using Null NRI.
This parameter defines the operator Null
NRI value for PS domain to select a
certain operator in a Multi Operator Core
Network.
NOTE: All operators must have their
specific Null NRI.
NOTE: Null NRI value cannot be
given to any SGSN of the pool.
NOTE: Operator cannot have same
null-NRI as others.
Related parameters
NRIMaxForPSCN of IUPS
NRIMinForPSCN of IUPS
NullNRIForPSPool of IUO
NRIMaxForPSCN of IUPS - The Null NRI
value cannot be given to any SGSN of
the pool.
NRIMinForPSCN of IUPS - The Null NRI
value cannot be given to any SGSN of
the pool.
NullNRIForPSPool of IUO - The operator
cannot have same null-NRI as the others.
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
Multi-Operator Core Network (optional)
OperatorWeight (Operator Weight)
272
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
This parameter defines the percentage
weight value of each operator in MultiOperator Core Network (MOCN).
Operator weight is used for the weighted
round robin method to select a CN operator. Load sharing among operators is
defined by configuring OperatorWeight.
Weight is divided among all operators
like:
OP1 50%
OP2 30%
OP3 20%
Weight value range is between 0 and
100. The total sum of every operator's
weight is 100 or 0.
If the weight value is 0 for all operators, it means that the equal load is
shared among all operators.
If the weight value is 100 for one
operator and all other operators are 0, it
means the operator with 100% load is the
default operator.
This parameter defines the weight value
of each operator in Multi-Operator Core
Network (MOCN). Operator weight is
used for the weighted round robin
method to select a CN operator. Load
sharing among operators is defined by
configuring OperatorWeight.
Weight is divided among all operators
like:
OP1 60
OP2 50
OP3 40
Thus the actual weight value used in
load sharing calculation for e.g. OP1
would be individual weigh value divided
by sum of weight values,
60/(60+50+40)=0.4. Weight value range
is between 0 and 100.If the weight value
is identical for all operators, it means that
the equal load is shared among all operators.
If the weight value is greater than 0
for one operator and all other operators
are 0, it means this one operator is the
default operator, getting the full load.
Units
%
PLMNid (PLMN identity)
Field
Description
DN70456011
Issue 05E
Issue 06
A Public Land Mobile Network is uniquely
identified by its PLMN identity. PLMNid
consists of Mobile Country Code (MCC)
and Mobile Network Code (MNC).
PLMN identity is an optional parameter, but needs to be configured with
proper values when configuring the
MOCN feature.
This parameter is primary Public Land
Mobile Network ( PLMN ) identity of the
operator. A Public Land Mobile Network
is uniquely identified by its PLMN identity.
PLMN identity consists of Mobile Country
Code (MCC) and Mobile Network Code
(MNC).
PLMNId cannot be modified if it is
mapped to any WCEL or CBCI.
Id:0900d80580a2e11c
Confidential
273
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Related parameters
Issue 05E
Issue 06
CommonMCC of IADA - Common PLMN
id (CommonMCC and CommonMNC)
can't be the same as any PLMNid in
IuOperator
CommonMCC of IADA - Common PLMN
id (CommonMCC and CommonMNC)
can't be the same as any PLMNid in IUO
instances.
CommonMNC of IADA - Common PLMN
id (CommonMCC and CommonMNC)
can't be the same as any PLMNid in
IuOperator
CommonMNC of IADA - Common PLMN
id (CommonMCC and CommonMNC)
can't be the same as any PLMNid in IUO
instances.
SharedAreaPLMNid of IUO - SharedAreaPLMNid can't be the same as any
primary PLMNid in IUO instances.
Related features
Multioperator RAN (optional) OR
Flexible Iu (optional) OR Multi-Operator
Core Network (optional)
SharedAreaPLMNid/SharedAreaMCC (Shared area Mobile Country Code)
Field
Issue 05E
Issue 06
Description
The parameters Shared area mobile
country code and Shared area mobile
network code compose the identifier of a
PLMN to which the subscribers of the
partner operator can have access.
The parameters Shared area mobile
country code and Shared area mobile
network code compose the identifier of a
PLMN to which the subscribers of the
partner operator can have access.
These parameters cannot be
modified in case they are mapped to any
WCEL.
Related parameters
SharedAreaPLMNid of IUO
Parameter relationships
-
Related features
IMSI Based Handover (optional)
IMSI Based Handover (optional) OR
Multi-Operator Core Network (optional)
SharedAreaPLMNid/SharedAreaMNC (Shared area Mobile Network Code)
Field
274
Issue 05E
Issue 06
Description
The parameters Shared area mobile
country code and Shared area mobile
network code compose the identifier of a
PLMN to which the subscribers of the
partner operator can have access.
The parameters Shared area mobile
country code and Shared area mobile
network code compose the identifier of a
PLMN to which the subscribers of the
partner operator can have access.
These parameters cannot be
modified in case they are mapped to any
WCEL
Related features
IMSI Based Handover (optional)
IMSI Based Handover (optional) OR
Multi-Operator Core Network (optional)
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
SharedAreaPLMNid/SharedAreaMNClength (Shared area Mobile Network Code
Length)
Field
Issue 05E
Issue 06
Description
The parameter defines whether 2 or 3
digits are used in the shared area mobile
network code.
When modifying this parameter,
also the value of the MNC used by the
system is always changed.
The parameter defines whether 2 or 3
digits are used in the shared area mobile
network code.
When modifying this parameter,
also the value of the MNC used by the
system is always changed.
SharedAreaPLMNid cannot be
modified in case it is mapped to any
WCEL.
Related features
IMSI Based Handover (optional)
IMSI Based Handover (optional) OR
Multi-Operator Core Network (optional)
SharedAreaPLMNid (Shared area PLMN identity)
Field
Description
Issue 05E
The parameter uniquely identifies the
shared Public Land Mobile Network to
which the subscribers of the partner
operator can have access. The SharedAreaPLMNid consists of the Mobile
Country Code (MCC) and Mobile
Network Code (MNC).
Related parameters
DN70456011
Issue 06
This parameter is secondary Public Land
Mobile Network ( PLMN ) identity of the
operator. The parameter uniquely identifies the shared Public Land Mobile
Network to which the subscribers of the
partner operator can have access. The
SharedAreaPLMNid consists of the
Mobile Country Code (MCC) and Mobile
Network Code (MNC). In-case of IMSI
Based HO, Operator can configure
WCEL with SharedAreaPLMNid in
addition to primary PLMNid except when
MOCN or MORAN is configured.. Also
CBCI is associated with SharedAreaPLMNids in case of IMSI based HO
is activated without MORAN and MOCN.
SharedAreaPLMNids are configured
for MOCN in order to support the usage
of several PLMNIds in network. When
routing is based on IMSI and PLMNId in
IMSi matches one of the SharedAreaPLMNids, the UE can be routed to
the CN for which the primary PLMNId has
been configured.
SharedAreaPLMNId cannot be
modified if it is mapped to any WCEL.
PLMNid of IUO - Shared area PLMNid
can't be same as any PLMNid in IUO
instances.
Id:0900d80580a2e11c
Confidential
275
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Related features
IMSI Based Handover (optional)
Issue 06
IMSI Based Handover (optional) OR
Multi-Operator Core Network (optional)
IUPS
PSCNNRI/NRIMaxForPSCN (Maximum value of NRI range for PS Core routing)
Field
Related parameters
Issue 05E
Issue 06
CNDRXLength of IUPS - NRIMinForPSCN and NRIMaxForPSCN can be configured to have the same value, indicating
one NRI value instead of value range.
PSCNNRI/NRIMinForPSCN (Minimum value of NRI range for PS Core routing)
Field
Related parameters
Issue 05E
Issue 06
CNDRXLength of IUPS - NRIMinForPSCN and NRIMaxForPSCN can be configured to have the same value, indicating
one NRI value instead of value range.
NetworkInd (Network indicator)
Field
Issue 05E
Related parameters
Issue 06
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
CNDomainVersion (Release version of Core Network)
276
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Range and step
Summary of changes
Issue 05E
1 (R99), 2 (Rel4), 3 (Rel5), 4 (Rel6), 5
(Rel7), 6 (Rel8), 7 (Rel9)
Issue 06
1 (R99), 2 (Rel4), 3 (Rel5), 4 (Rel6), 5
(Rel7), 6 (Rel8), 7 (Rel9), 8 (Rel10), 9
(Rel11), 10 (Rel12)
SignPointCode (Signalling point code)
Field
Issue 05E
Issue 06
Description
The code that uniquely identifies the signalling point in the signalling network.
The parameter is not modifiable if the
core network is active. Parameter modification terminates ongoing calls.
The code identifies the signaling point in
the signaling network.
Combination of NetworkInd and SignPointCode uniquely identifies a Signalling Point.
The parameter is not modifiable if the
core network is active. Parameter modification terminates ongoing calls.
Related parameters
NetworkInd of IUPS
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
PagingOptSupport (Support of Paging Optimization Feature)
Field
Description
DN70456011
Issue 05E
Issue 06
This parameter controls whether Paging
Optimization Feature is used for this IU
interface or not. If enabled then for
pagings received on this interface, I-BTS
will distribute the paging message among
paging group members.
This parameter controls whether Paging
Optimization Feature is used for this IU
interface or not. If enabled then for
pagings received on this interface, FDBTS will distribute the paging message
among paging group members.
Id:0900d80580a2e11c
Confidential
277
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Range and step
0 (disabled), 1 (enabled)
0 (Disabled), 1 (Enabled)
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC
IUPSIP
DestIPAddressPS (IP address for the IUPS destination subnet)
278
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
The DestIPAddressPS attribute with the
IPNetmaskPS parameter forms a destination IP subnet definition for the Iu-PS
user plane connections (GTP tunnels).
The RNC performs the IP Based Route id
reference selection for the new Iu-PS
connection in between the destination IP
subnet and the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUPSIP
object instance needed under the IUPS
object instance. Example IPv4: 0.0.0.0 / 0
-> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUPSIP objects under the IUPS.
Example IPv4: IUPSIP#1 192.168.0.0 /
28 -> IP Based Route id y, IUPSIP#2
192.168.0.16 / 28 -> IP Based Route id z.
Note: This parameter is configured
in the following cases:
- IP over Ethernet transport option
with cRNC NPGE, mcRNC and I-HSPA
- IP over ATM option with an
cRNC/NPS1 based network interface
- Always used with I-HSPA Iu-PS
configuration
As an exception the parameter is not
used with cRNC GTPU/NIS HW based
Iu-PS interface.
The DestIPAddressPS attribute with the
IPNetmaskPS parameter forms a destination IP subnet definition for the Iu-PS
user plane connections (GTP tunnels).
The RNC performs the IP Based Route id
reference selection for the new Iu-PS
connection in between the destination IP
subnet and the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUPSIP
object instance needed under the IUPS
object instance. Example IPv4: 0.0.0.0 / 0
-> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUPSIP objects under the IUPS.
Example IPv4: IUPSIP#1 192.168.0.0 /
28 -> IP Based Route id y, IUPSIP#2
192.168.0.16 / 28 -> IP Based Route id z.
Note: This parameter is configured
in the following cases:
- IP over Ethernet transport option
with cRNC NPGE, mcRNC and Flexi
Direct RNC
- IP over ATM option with an
cRNC/NPS1 based network interface
- Always used with Flexi Direct RNC
Iu-PS configuration
As an exception the parameter is not
used with cRNC GTPU/NIS HW based
Iu-PS interface.
Default value
-
0.0.0.0
Default value notes
DN70456011
Referred IP Based Route gets selected
regardless of the IP address signaled by
the CN.
Id:0900d80580a2e11c
Confidential
279
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Related features
Issue 05E
IP based Iu-PS (optional)
Issue 06
IP based Iu-PS (optional) OR Basic
functions (standard)
IPBasedRouteIdPS (IP Based Route Identifier for IUPS)
Field
Issue 05E
Issue 06
Description
The IPBasedRouteId refers to the logical
IP Based Route entity configured in the
IP layer with MML or via the IP Plan interface. The IP Based Route configured for
the Iu-PS interface is used for the user
plane connections towards the Iu-PS CN
element controlling the interface unit and
port selection along with the source IP
address and UDP port selection.
Note: This parameter is configured
when the IP over Ethernet transport
option (NPGE) is used and when the
IPoA option is used with an NPS1 based
network interface unit. The parameter is
not used with the GTPU/NIS HW based
Iu-PS interface.
The IPBasedRouteId refers to the logical
IP Based Route entity configured in the
IP layer with MML/SCLI or via the IP Plan
interface. The IP Based Route configured
for the Iu-PS interface is used for the user
plane connections towards the Iu-PS CN
element controlling the interface unit and
port selection along with the source IP
address and UDP port selection.
Note: The IUPSIP parameters are
configured with IP over Ethernet transport option. In addition the IUPSIP configuration is needed with IPA-RNC:NPS1
based network interface unit (IPoA). The
IUPSIP parameters are not used with the
IPA-RNC:GTPU/NIS HW based Iu-PS
interface (IPoA).
Default value
0
Default value notes
Value not defined.
Special value
0
Related features
IP based Iu-PS (optional) OR Basic
functions (standard)
IPNetmaskPS (IP netmask for the IUPS destination subnet)
280
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
The IPNetmaskPS with the DestIPAddressPS attribute forms a destination IP
subnet definition for the Iu-PS user plane
connections (GTP tunnels). The RNC
performs the IP Based Route id reference
selection for the new Iu-PS connection in
between the destination IP subnet and
the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signalled by
the CN and there is only one IUPSIP
object instance needed under the IUPS
object instance. Example IPv4: 0.0.0.0 /
0.0.0.0 -> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUPSIP objects under the IUPS.
Example IPv4: IUPSIP#1 192.168.0.0 /
255.255.255.240 -> IP Based Route id y,
IUPSIP#2 192.168.0.16 /
255.255.255.240 -> IP Based Route id z.
Note: This parameter is configured
in the following cases:
- IP over Ethernet transport option
with cRNC NPGE, mcRNC and I-HSPA
- IP over ATM option with an
cRNC/NPS1 based network interface
- Always used with I-HSPA Iu-PS
configuration
As an exception the parameter is not
used with cRNC GTPU/NIS HW based
Iu-PS interface.
The IPNetmaskPS with the DestIPAddressPS attribute forms a destination IP
subnet definition for the Iu-PS user plane
connections (GTP tunnels). The RNC
performs the IP Based Route id reference
selection for the new Iu-PS connection in
between the destination IP subnet and
the destination IP address
(RANAP:Transport Layer Address) that
is received at the RAB assignment
request.
There has to be at least one IP Based
Route id reference towards a certain CN
element. In most of the cases one IP
Based Route instance reference is
enough and the destination IP subnet can
be set simply to 0.0.0.0/0. The configured
IP Based Route id reference is then
selected for any IP address signaled by
the CN and there is only one IUPSIP
object instance needed under the IUPS
object instance. Example IPv4: 0.0.0.0 /
0.0.0.0 -> IP Based Route id x.
In case that several IP Based Route
references are needed towards a certain
CN element the subnet specific references can be added with configuring
several IUPSIP objects under the IUPS.
Example IPv4: IUPSIP#1 192.168.0.0 /
255.255.255.240 -> IP Based Route id y,
IUPSIP#2 192.168.0.16 /
255.255.255.240 -> IP Based Route id z.
Note: This parameter is configured
in the following cases:
- IP over Ethernet transport option
with cRNC NPGE, mcRNC and Flexi
Direct RNC
- IP over ATM option with an
cRNC/NPS1 based network interface
- Always used with Flexi Direct RNC
Iu-PS configuration
As an exception the parameter is not
used with cRNC GTPU/NIS HW based
Iu-PS interface.
Default value notes
DN70456011
Referred IP Based Route gets selected
regardless of the IP address signaled by
the CN.
Id:0900d80580a2e11c
Confidential
281
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Related features
IP based Iu-PS (optional)
Issue 06
IP based Iu-PS (optional) OR Basic
functions (standard)
IPQMIdPS (IPQM object id for IuPS)
Field
Issue 05E
Issue 06
Parameter Name
IPQM object id for IuItemPS
IPQM object id for IuPS
Description
The IPQM identification gives the reference to the IPQM object used for the PS
CN. The IPQM object defines the UMTS
traffic class to DSCP mapping to be used
for the IP connections at the Iu interface.
Note: This parameter is configured
when the IP over Ethernet transport
option (NPGE) is used and when the
IPoA option is used with an NPS1 based
network interface unit. The parameter is
not used with the GTPU/NIS HW based
Iu-PS interface.
The IPQM identification gives the reference to the IPQM object used for the PS
CN. The IPQM object defines the UMTS
traffic class to DSCP mapping to be used
for the IP connections at the Iu interface.
The referred IPQM instance has to exist
in the system before IUPSIP is created.
Note for IPA-RNC: This parameter is
configured when the IP over Ethernet
transport option (NPGE) is used and
when the IPoA option is used with an
NPS1 based network interface unit. The
parameter is not used with the GTPU/NIS
HW based Iu-PS
Range and step
0..8, step 1
1..8, step 1
Default value
0
Default value notes
0 means that the IPQM reference is not
given and the default values are used.
Related parameters
IPQMId of IPQM - The IPQM object
instance referred by IPQMIdPS has to
exist.
Related features
IP based Iu-PS (optional) OR Basic
functions (standard)
IUPSIPId (IUPSIP Identifier )
Field
Issue 05E
Related features
Issue 06
IP based Iu-PS (optional) OR Basic
functions (standard)
IUR
InterfaceMode (Configure the IUR in a special mode)
282
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
This parameter allows configuring the
interface to the neighboring RNC in a
mode that is deviating from
3GPPstandard and NSN-conform way.
Such a configuration can waste RNC
resources or compromise its performance.
This parameter allows configuration of
the interface to the neighboring RNC in a
way that deviates from 3GPP and Nokia
Siemens Networks standards. Note that
such a configuration might waste RNC
resources or compromise its performance.
Default value notes
Do not use any other value if not specifically advised by NSN
Do not use any other value unless specifically advised by Nokia Siemens Networks.
ADAURAId (FD-RNC neighboring Adapter shared URA identity)
Field
Issue 05E
Issue 06
Parameter Name
I-HSPA neighboring Adapter shared
URA identity
FD-RNC neighboring Adapter shared
URA identity
Interfaces
IADA<->UE, RAC<->IADA, EM<->IADA,
RACApp<->RAC, IADA<->WBTS,
WBTS<->UE
RNC<->UE, RAC<->RNC, EM<->RNC,
RACApp<->RAC, RNC<->WBTS,
WBTS<->UE
HSDPACCEnabledIur (HSDPA Congestion Control activation Iur)
Field
Issue 05E
Related parameters
Issue 06
HSPAOverIur of IUR - HSDPACCEnabledIur should not be set as Enabled if
HSPAOverIur is Disabled.
HSPAOverIur (HSPA over Iur)
DN70456011
Id:0900d80580a2e11c
Confidential
283
Summary of changes
Field
Related parameters
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
NRncVersion of IUR - The system checks
if the release version of Neighboring RNC
is Rel'6 or later before the activation of
the HSPA over Iur feature.
IurUPSupport of IUR - IUR-HSPAOverIur
cannot be supported, if IurUPSupport is
not supported.
HSDPADynamicResourceAllocation of
RNFC - The system checks if the HSDPA
Dynamic Resource Allocation feature is
activated before the activation of the
HSPA over Iur feature.
HSDPAMobility of RNFC - The system
checks if the HSDPA Serving Cell
Change feature is activated before the
activation of the HSPA over Iur feature.
NRncVersion of IUR - The system checks
if the release version of Neighboring RNC
is Rel'6 or later before the activation of
the HSPA over Iur feature.
HSDPACCEnabledIur of IUR HSPAOverIur should not be set as
Disabled if HSDPACCEnabledIur is
Enabled.
HSDPADynamicResourceAllocation of
RNFC - The system checks if the HSDPA
Dynamic Resource Allocation feature is
activated before the activation of the
HSPA over Iur feature.
HSDPAMobility of RNFC - The system
checks if the HSDPA Serving Cell
Change feature is activated before the
activation of the HSPA over Iur feature.
AppAwareRANEnabled of IUR - The
system shall prevent the modification of
HSPAOverIur parameter value from '1' to
'0' if AppAwareRANEnabled parameter is
set to Enabled.
IBTSSharing (IBTS Sharing)
284
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
IurUPSupport of IUR - This parameter
indicates user plane procedure support of
the Iur connection. IBTSSharing parameter can be set to "1" only if the IurUPSupport is "1" for the neighbouring I-HSPA
Adapter.
NRncRelocationSupport of IUR - This
parameter identifies whether a neighbouring RNC supports the relocation of
SRNC or not. IBTSSharing parameter
can be set to '1' only if the neighbouring
Flexi Direct RNC supports relocation of
SRNC.
NRncRelocationSupport of IUR - This
parameter identifies whether a neighbouring RNC supports the relocation of
SRNC or not. IBTSSharing parameter
can be set to '1' only if the neighbouring IHSPA Adapter supports relocation of
SRNC.
NeighbouringRNWElement of IUR NeighbouringRNWElement indicates if
the neighbouring RNC is an 3G WCDMA
RNC or an I-HSPA Adapter. The
IBTSSharing parameter can be set to "1"
only if the neighbouring RNW element is
an I-HSPA Adapter.
NeighbouringRNWElement of IUR NeighbouringRNWElement indicates if
the neighbouring RNC is an 3G WCDMA
RNC or an Flexi Direct RNC. The
IBTSSharing parameter can be set to "1"
only if the neighbouring RNW element is
an Flexi Direct RNC.
MaxFPDLFrameSizeIur (Maximum FP downlink frame size Iur)
Field
Issue 05E
Issue 06
Description
The user plane frame size can be limited
with this parameter in order to avoid IP
layer fragmentation. The RNC takes the
value into account during DL User Plane
traffic processing and limits the maximum
HS-DSCH FP frame size accordingly.
The value has to be planned according to
the minimum IP layer MTU along the path
to the DRNC and BTS. The IP and UDP
header overheads have to be subtracted
from the IP interface MTU value (e.g.
IPv4 IP header 20 bytes, UDP header 8
bytes) when adjusting the value, since
the parameter directly controls the user
plane FP frame size.
The user plane frame size can be limited
with this parameter in order to avoid IP
layer fragmentation. The RNC takes the
value into account in DL User Plane
traffic processing and limits the maximum
HS-DSCH FP frame size accordingly.
The value has to be planned according to
the minimum IP layer MTU along the path
to the DRNC and BTS. The parameter is
applied in SRNC to both ATM and IP Iur
interfaces.
The IP and UDP header overheads
have to be subtracted from the IP interface MTU value (e.g. IPv4 IP header 20
bytes, UDP header 8 bytes) when adjusting the value since the parameter directly
controls the user plane FP frame size.
Range and step
540..9000, step 1
540..1472, step 1
Units
Default value
DN70456011
byte
1472
1428
Id:0900d80580a2e11c
Confidential
285
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Interfaces
RAC<->RNC, EM<->RNC, RACApp<>RAC
RNC<->RAC, RNC<->EM, RACApp<>RAC
Related features
IP Based Iur (optional)
IP Based Iur (optional) OR HSPA InterRNC Cell Change (optional)
MaxIurNRTHSDSCHBitRate (Maximum NRT HS-DSCH MAC-d flow bit rate over Iur)
Field
Range and step
Issue 05E
0..9600, step 128
Issue 06
128..9600, step 128
NeighbouringPLMNid/MCC (Mobile Country Code)
Field
Modification
Issue 05E
unmodifiable
Issue 06
onLine
NeighbouringPLMNid/MNC (Mobile Network Code)
Field
Issue 05E
Issue 06
Description
Unique network identification within
country. MNC consists of two or three
digits. MNC together with MCC identifies
the PLMN uniquely (globally).
Unique network identification within
country. MNC consists of two or three
digits. MNC together with MCC identifies
the PLMN uniquely (globally).
If you modify the MNC, you might
have to also adjust the MNC length.
Modification
unmodifiable
onLine
Related parameters
MNCLength of IUR
MNCLength of IUR - This parameter shall
be defined with 2 digit or 3 digit based on
MNCLength.
NeighbouringPLMNid/MNCLength (Mobile Network Code Length)
Field
Issue 05E
Issue 06
Modification
unmodifiable
onLine
Related parameters
MNC of IUR
MNC of IUR - This parameter defines
whether 2 or 3 digits are used in the
Mobile Network Code.
NRncId (Neighbour RNC identifier)
286
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
This parameter identifies the neighbour
RNC. A unique identification for an RNC
node within the UTRAN.
This parameter identifies the neighbor
RNC. A unique identification for an RNC
node within the UTRAN.
For RAN 2054 feature "Extension of
RNC ids" only, extended range of
4096..65534 will be used , otherwise
older range 1..4095 will be used as this
extended range violates 3GPP specifications.
Related parameters
NRncVersion of IUR - NRNCID can be
set greater than 4095, if NRncVersion is
Rel7 or higher.
NeighbouringRNWElement of IUR NRNCID can be set greater than 4095
only, if NeighbouringRNWElement is
Flexi Direct RNC.
NRncNetworkInd (Network indicator of neighbour RNC)
Field
Related parameters
Issue 05E
NetworkInd of IUPS
Issue 06
NRncSignPointCode of IUR - Combination of NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
OverbookingSwitchIur (Overbooking Switch Iur)
Field
Range and step
DN70456011
Issue 05E
0 (DISABLED), 1 (ENABLED)
Id:0900d80580a2e11c
Confidential
Issue 06
0 (Disabled), 1 (Enabled)
287
Summary of changes
Radio Network Parameters in Flexi Direct
NRncVersion (Release version of Neighbouring RNC)
Field
Issue 05E
Related parameters
Issue 06
NRncId of IUR - NRNCID can be set
greater than 4095, if NRncVersion is Rel7
or higher.
NeighbouringRNWElement of IUR NRncVersion must be greater than or
equal to Rel6, if NeighbouringRNWElement is Flexi Direct RNC.
NRncRelocationSupport (Serving RNC Relocation Support of neighbour RNC)
Field
Related parameters
Issue 05E
Issue 06
RelocationSupport of IUCS
NRncSignPointCode (Signalling point code of neighbour RNC)
Field
Issue 05E
Issue 06
Description
The code that uniquely identifies the sig- The code identifies the signalling point in
nalling point in the signalling network.
the signalling network.
Combination of NRncNetworkInd and
NRncSignPointCode uniquely identifies a
Signalling Point.
Related parameters
NRncNetworkInd of IUR
SignPointCode of IUPS
NRncNetworkInd of IUR - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUPS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NetworkInd of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
SignPointCode of IUCS - Combination of
NetworkInd and SignPointCode be
unique within IUCS, IUPS and IUR
instances.
NeighbouringRNWElement (Type of the Neighbouring RNW Element)
288
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
This parameter indicates whether the
neighboring WCDMA Controller Node is
a 3G RNC or an I-HSPA Adapter.
This parameter indicates whether the
neighboring WCDMA Controller Node is
a 3G RNC or a Flexi Direct RNC.
Range and step
0 (3G-WCDMA RNC), 1 (I-HSPA
Adapter)
0 (3G-WCDMA RNC), 1 (Flexi Direct
RNC)
Related parameters
NRncId of IUR - NRNCID can be set
greater than 4095 only, if NeighbouringRNWElement is Flexi Direct RNC.
NRncVersion of IUR - NRncVersion must
be greater than or equal to Rel6, if NeighbouringRNWElement is Flexi Direct
RNC.
IurUPSupport (User Plane support of Iur connection)
Field
Issue 05E
Related parameters
Issue 06
HSPAOverIur of IUR - IurUPSupport
cannot be set to “Not supported” if IURHSPAOverIur is enabled.
PFL
AMRToNonPreferredLayer (AMR to Non Preferred Layer)
Field
Range and step
Issue 05E
0 (disabled), 1 (enabled)
Issue 06
0 (Disabled), 1 (Enabled)
LaySelLowLoadPref (Layer Selection Low Load Preferred)
Field
Range and step
Issue 05E
0 (disabled), 1 (enabled)
Issue 06
0 (Disabled), 1 (Enabled)
RNAC
DLmaxBitRatePerSF/DLmaxBitRateSF128 (Maximum DL bit rate with spreading factor
128)
DN70456011
Id:0900d80580a2e11c
Confidential
289
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Related parameters
Issue 05E
Issue 06
DLmaxBitRateSF256 of RNAC - Value of
the parameter shall be bigger than the
value of the parameter
DLmaxBitRateSF256.
DLmaxBitRateSF256 of RNAC - Value of
the parameter must be bigger than the
value of the parameter
DLmaxBitRateSF256.
DLmaxBitRateSF64 of RNAC - Value of
the parameter shall be smaller than the
value of the parameter
DLmaxBitRateSF64.
DLmaxBitRateSF64 of RNAC - Value of
the parameter must be smaller than the
value of the parameter
DLmaxBitRateSF64.
DLpuncturingLimit of RNAC
DLpuncturingLimit of RNAC
PCrangeDL (Radio link downlink power control range)
Field
Default value
Issue 05E
15
Issue 06
20
SRBDelay (SRB delay)
Field
Description
Issue 05E
Issue 06
The parameter defines the number of
frames after the PC preamble period
during which the transmission of data on
the RRC Signalling Radio Beares should
be suspended by the UE. The SRB delay
can be applied to the physical layer synchronization procedure A when the first
radio link set is established for the UE.
The parameter defines the number of
frames after the PC preamble period
during which the transmission of data on
the RRC Signalling Radio Bearers should
be suspended by the UE. The SRB delay
can be applied to the physical layer synchronization procedure A when the first
radio link set is established for the UE.
UlScrCodeMin (Uplink scrambling code minimum value)
290
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
This parameter defines the minimum
value of the uplink scrambling code.
From RN4.0 Inc 1 onwards, this
parameter is used for defining the start of
the scrambling code value and the range
of the uplink scrambling codes that are
possible to allocate in the RNC. The
range of the uplink scrambling codes allocated by RNC starts from the value of the
UlScrCodeMin parameter and the last
value of the uplink scrambling code is
UlScrCodeMin + the number of ICSU
units * the maximum number of users per
ICSU.
Actually the last indexed value
depends on the value of the UlScrCodeMin. For example, if the value is set to
16777215, it continues allocation from
the value 8192. If the maximum number
of ICSU units is 4 and the maximum
number of users in RNC is 8192, then
RNC allocates the value 16777215 and
values from 8192 to 40959.
The uplink scrambling code is unique
for each MS and it is used continuously,
even if the frequency is changed. The
first 0...8191 scrambling codes are
reserved to be used in inter-RAT handovers from GSM to UTRAN.
All uplink physical channels are subjected to scrambling with a complexvalued scrambling code. The UL DPCH
will be scrambled with a long scrambling
code.
This parameter defines the minimum
value of the uplink scrambling code.
From RN4.0 Inc 1 onwards, this
parameter is used for defining the start of
the scrambling code value and the range
of the uplink scrambling codes that are
possible to allocate in the RNC. The
range of the uplink scrambling codes allocated by RNC starts from the value of the
UlScrCodeMin parameter and the last
value of the uplink scrambling code is
UlScrCodeMin + the number of ICSU
units * the maximum number of users per
ICSU.
Actually the last indexed value
depends on the value of the UlScrCodeMin. For example, if the value is set to
16777215, it continues allocation from
the value 8192. If the maximum number
of ICSU units is 4 and the maximum
number of users in RNC is 8192, then
RNC allocates the value 16777215 and
values from 8192 to 40959.
The uplink scrambling code is unique
for each MS and it is used continuously,
even if the frequency is changed. The
first 0...8191 scrambling codes are
reserved to be used in inter-RAT handovers from GSM to UTRAN.
All uplink physical channels are subjected to scrambling with a complexvalued scrambling code. The UL DPCH
will be scrambled with a long scrambling
code.
Note: If this parameter is modified,
RNC need to be restarted immediately so
that the RNC takes the new value into
use.
LoadBasedAMRCodecMode (Usage of Load based AMR codec mode selection)
Field
Range and step
Issue 05E
0 (disabled), 1 (enabled)
Issue 06
0 (Disabled), 1 (Enabled)
RNFC
SignConnActivitySupervision (Activity supervision for NAS signaling connection)
DN70456011
Id:0900d80580a2e11c
Confidential
291
Summary of changes
Field
Related parameters
Radio Network Parameters in Flexi Direct
Issue 05E
MSActivitySupervision of IADA - When
there is a PS-RAB configured in the MS,
the supervision of inactive Iu-PS connection is managed by using the MSActivitySupervision timer.
RANAPprocInitWait of IADA - See the
parameter description.
CVUserInactInSignConnRel of RNFC This parameter allows usage of the
RANAP cause value 'User Inactivity' in
RANAP:Iu Release Request procedure
when the RNC is releasing an inactive
signaling connection towards the PS-CN.
Issue 06
RANAPprocInitWait of IADA - See the
parameter description.
CVUserInactInSignConnRel of RNFC This parameter allows usage of the
RANAP cause value 'User Inactivity' in
RANAP:Iu Release Request procedure
when the RNC is releasing an inactive
signaling connection towards the PS-CN.
MSActivitySupervision of WAC - When
there is a PS-RAB configured in the MS,
the supervision of inactive Iu-PS connection is managed by using the MSActivitySupervision timer.
CSVoiceServiceSupport (CS Voice Service Support in FD-RNC)
Field
Issue 05E
Issue 06
Parameter Name
CS Voice Service Support in I-HSPA
CS Voice Service Support in FD-RNC
Description
This parameter defines the CS Service
Deployment in the I-HSPA network. The
following deployment scenarios are
possible in Adapter with respect to CS
Voice Services Support.
i. No CS Voice Services (PS Only
Network)
ii. CS Enabling HO to overlaying 2G
network (Overlay deployment)
iii. CS Voice Supported - CS Voice
supported in Adapter
Operator can configure this parameter to enable desired deployment scenario.
Also the third value, i.e "CS Voice
Supported" is allowed to be set only in
case the license for I-HSPA CS Voice
Enabler is set to ON. If this license is OFF
then only the first two values are allowed
to be set.
This parameter defines the CS Service
Deployment in the FD-RNC network. The
following deployment scenarios are
possible in Adapter with respect to CS
Voice Services Support.
i. No CS Voice Services (PS Only
Network)
ii. CS Enabling HO to overlaying 2G
network (Overlay deployment)
iii. CS Voice Supported - CS Voice
supported in Adapter
Operator can configure this parameter to enable desired deployment scenario.
Also the third value, i.e "CS Voice
Supported" is allowed to be set only in
case the license for FD-RNC CS Voice
Enabler is set to ON. If this license is OFF
then only the first two values are allowed
to be set.
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC
HSDPA16KBPSReturnChannel (HSDPA 16 kbps UL DCH return channel on/off switch)
292
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
HSDPAenabled of WCEL - HSDPA must
be enabled in order to apply 16 kbps
return channel in HSDPA capable cell.
HSDPAenabled of WCEL - HSDPA must
be enabled in order to apply 16 kbps
return channel in HSDPA capable cell.
HSDPAinitialBitrateUL of RNHSPA - In
order to apply 16 kbps UL DCH return
channel, user should set initial bit rate
accordingly.
HSDPAinitialBitrateUL of WAC - In order
to apply 16 kbps UL DCH return channel,
user should set initial bit rate accordingly.
HSDPAminAllowedBitrateUL of
RNHSPA - In order to apply 16 kbps UL
DCH return channel, user should set
minimum bit rate accordingly.
HSDPAminAllowedBitrateUL of WAC - In
order to apply 16 kbps UL DCH return
channel, user should set minimum bit
rate accordingly.
PTTEnabled of RNFC - The system
prevents deactivation of the 16 kpbs DCH
return channel for HSDPA feature, if the
PTT feature is enabled.
MOCNenabled (Multi-Operator Core Network enabled)
Field
Related parameters
Issue 05E
Issue 06
MultiplePLMNListIncluded of WCEL - To
broadcast multiple PLMN list (IuOperator-PLMNIds) in a cell this parameter is
set to 'Multiple PLMN List broadcasted'.
MultiplePLMNListIncluded of WCEL - To
broadcast multiple PLMN list (IuOperator-PLMNIds) in a cell this parameter is
set to 'Multiple PLMN List broadcasted'.
MIBPLMNIdIncluded of RNFC - This
parameter can be modified if MOCNenabled is set to 'Disabled'.
MIBPLMNIdIncluded of RNFC - This
parameter can be modified if MOCNenabled is set to 'Disabled'.
CSCNDRXLength of IUO - CSCNDRXLength must be set with same value
among all IU Operators if RNFC-MOCNEnabled parameter is set as enabled.
PSCNDRXLength of IUO - PSCNDRXLength must be set with same value
among all IU Operators if RNFC-MOCNEnabled parameter is set as enabled.
CS_T3212 of IUO - CS_T3212 must be
set with same value among all IU Operators if RNFC-MOCNEnabled parameter
is set as enabled.
PS_NMO of IUO - PS_NMO must be set
with same value among all IU Operators
if RNFC-MOCNEnabled parameter is set
as enabled.
PSOpThroUsage (Throughput based optimisation of the PS algorithm usage)
DN70456011
Id:0900d80580a2e11c
Confidential
293
Summary of changes
294
Radio Network Parameters in Flexi Direct
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
DCHUtilBelowDowngradeThr of RNPS If the parameter PSOpThroUsage is
switched 'On', the value of the related
parameter DCHUtilBelowDowngradeThr
is applicable.
DCHUtilBelowDowngradeThr of RNPS If the parameter PSOpThroUsage is
switched 'On', the value of the related
parameter DCHUtilBelowDowngradeThr
is applicable.
DCHUtilLowerAveWinBitRate of RNPS If the parameter PSOpThroUsage is
switched 'On', the values of the related
parameter DCHUtilLowerAveWinBitRate
are applicable.
DCHUtilLowerAveWinBitRate of RNPS If the parameter PSOpThroUsage is
switched 'On', the values of the related
parameter DCHUtilLowerAveWinBitRate
are applicable.
DCHUtilLowerDowngradeThrBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilLowerDowngradeThrBitRate are applicable.
DCHUtilLowerDowngradeThrBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilLowerDowngradeThrBitRate are applicable.
DCHUtilLowerTimeToTriggerBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilLowerTimeToTriggerBitRate are applicable.
DCHUtilLowerTimeToTriggerBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilLowerTimeToTriggerBitRate are applicable.
DCHUtilMeasGuardTime of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilMeasGuardTime is applicable.
DCHUtilMeasGuardTime of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilMeasGuardTime is applicable.
DCHUtilRelAveWin of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilRelAveWin is applicable.
DCHUtilUpperAveWinBitRate of RNPS If the parameter PSOpThroUsage is
switched 'On', the values of the related
parameter DCHUtilUpperAveWinBitRate
are applicable.
DCHUtilRelThrDL of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilRelThrDL is applicable.
DCHUtilRelThrUL of RNPS - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilRelThrUL is applicable.
DCHUtilRelTimeToTrigger of RNPS - If
the parameter PSOpThroUsage is
switched 'On', the value of the related
parameter DCHUtilRelTimeToTrigger is
applicable.
DCHUtilUpperAveWinBitRate of RNPS If the parameter PSOpThroUsage is
switched 'On', the values of the related
parameter DCHUtilUpperAveWinBitRate
are applicable.
DN70456011
DCHUtilUpperDowngradeThrBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
Id:0900d80580a2e11c
related parameter DCHUtilUpperDownConfidential
gradeThrBitRate are applicable.
DCHUtilUpperTimeToTriggerBitRate of
DCHUtilUpperDowngradeThrBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilUpperDowngradeThrBitRate are applicable.
DCHUtilUpperTimeToTriggerBitRate of
RNPS - If the parameter PSOpThroUsage is switched 'On', the values of the
related parameter DCHUtilUpperTimeToTriggerBitRate are applicable.
DCHUtilRelAveWin of WAC - If the
parameter PSOpThroUsage is switched
'On', the value of the related parameter
DCHUtilRelAveWin is applicable.
DCHUtilRelThrDL of WAC - If the parameter PSOpThroUsage is switched 'On',
the value of the related parameter
DCHUtilRelThrDL is applicable.
DCHUtilRelThrUL of WAC - If the parameter PSOpThroUsage is switched 'On',
295
the value of the related parameter
DCHUtilRelThrUL is applicable.
DCHUtilRelTimeToTrigger of WAC - If
Summary of changes
Radio Network Parameters in Flexi Direct
WireLessPriorityService (Usage of the Wireless Priority Service)
Field
Related parameters
Issue 05E
Issue 06
ADJGId of ADJG - The target cell of
directed retry of WPS call is the cell
whose ADJGId parameter has value
zero.
ADJGId of ADJG - The target cell of
directed retry of WPS call is the cell
whose ADJGId parameter has value
zero.
AdjgSIB of ADJG - If Wireless Priority
Service feature is enabled, then AdjgSIB
shall be set to the default value (Yes).
AdjgSIB of ADJG - If Wireless Priority
Service feature is enabled, then AdjgSIB
must be set with the default value in
ADJG-0 instances under all the WCELs.
RNHSPA
HSDPASRBWindow (CPICH Ec/No window for SRBs on HS-DSCH cell selection)
Field
Description
296
Issue 05E
Issue 06
The parameter determines the maximum
allowed difference between the best cell
and the SRB on HS-DSCH cell. The
window is relative to the best cell in the
active set. If the SRB on HS-DSCH cell
change is outside the window, SRBs on
HS-DSCH cell change procedure is initiated. If the SRBs on HS-DSCH cell
change fails, it triggers SRBs on HSDSCH transport channel type switch to
DCH. The measured quantity is CPICH
Ec/No, which is received periodically
from the UE.
This parameter determines the maximum
allowed difference between the CPICH
Ec/No of the best active set cell and the
CPICH Ec/No of the serving HS-DSCH
cell when SRBs are mapped on EDCH/HS-DSCH. If the difference
between the averaged CPICH Ec/No
values exceeds the value of this parameter, serving HS-DSCH cell change procedure is initiated. If the serving HS-DSCH
cell change fails, SRBs are switched to EDCH/DCH or DCH/DCH configuration.
This parameter is overruled if Fast
HSPA mobility is enabled in the serving
HS-DSCH cell with the WCEL parameter
FastHSPAMobilityEnabled and the
maximum allowed difference between
the best active set cell and the serving
HS-DSCH cell is determined on cell level
with the WCEL parameter HSDPASRBWindow of the serving HS-DSCH cell.
The RNMOBI parameters HSDPACPICHReportPeriod and HSDPACPICHAveWindow (or the
corresponding WCEL parameters) determine the reporting period of the periodical
intra-frequency CPICH Ec/No measurement, which is used as a criterion for the
serving HS-DSCH cell change procedure, and the averaging window for the
periodical CPICH Ec/No measurement
reports respectively.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
CPCNRT10msTTI/N10msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 10ms
TTI)
Field
Description
Issue 05E
Issue 06
The parameter defines the CQI feedback
cycle for HSDPA when the CQI reporting
is not reduced because of DTX. This is
part of CQI Reporting reduction subfeature.
This parameter is used for NRT
when 10 ms TTI is used on E-DCH.
Note! CQI reporting cycles values
bigger than 10ms are not recommended
CQI feedback cycle shorter than 4
ms is not allowed if DC-HSDPA and
MIMO are simultaneously configured in
use for the UE.
DC-HSDPA with MIMO simultaneously configured in use for the UE
doubles the amount of CQI reporting. UE
sends two consecutive CQI reports: one
for the primary carrier immediately
followed by another one for the secondary carrier. This affects performance of
the CQI reporting reduction.
The parameter defines the CQI feedback
cycle for HSDPA when the CQI reporting
is not reduced because of DTX. This is
part of CQI Reporting reduction subfeature.
This parameter is used for NRT
when 10 ms TTI is used on E-DCH.
Note! CQI reporting cycles values
bigger than 10ms are not recommended.
CQI feedback cycle shorter than 4
ms is not allowed if DC-HSDPA and
MIMO are simultaneously configured in
use for the UE.
DC-HSDPA with MIMO simultaneously configured in use for the UE
doubles the amount of CQI reporting. UE
sends two consecutive CQI reports: one
for the primary carrier immediately
followed by another one for the secondary carrier. This affects performance of
the CQI reporting reduction.
CPCNRT2msTTI/N2msCQIFeedbackCPC (CQI Feedback Cycle for CPC NRT 2ms
TTI)
DN70456011
Id:0900d80580a2e11c
Confidential
297
Summary of changes
Field
Description
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
The parameter defines the CQI feedback
cycle for HSDPA when the CQI reporting
is not reduced because of DTX. This is
part of CQI Reporting reduction subfeature.
This parameter is used for NRT
when 2 ms TTI is used on E-DCH.
Note! CQI reporting cycles values
bigger than 10ms are not recommended
Note! This parameter value must
be an integer divisor or a multiple of the
parameter N2msUEDTXCycle2 value.
CQI feedback cycle shorter than 4
ms is not allowed if DC-HSDPA and
MIMO are simultaneously configured in
use for the UE.
DC-HSDPA with MIMO simultaneously configured in use for the UE
doubles the amount of CQI reporting. UE
sends two consecutive CQI reports: one
for the primary carrier immediately
followed by another one for the secondary carrier. This affects performance of
the CQI reporting reduction.
The parameter defines the CQI feedback
cycle for HSDPA when the CQI reporting
is not reduced because of DTX. This is
part of CQI Reporting reduction subfeature.
This parameter is used for NRT
when 2 ms TTI is used on E-DCH.
Note! CQI reporting cycles values
bigger than 10ms are not recommended.
Note! This parameter value must
be an integer divisor or a multiple of the
parameter N2msUEDTXCycle2 value.
CQI feedback cycle shorter than 4
ms is not allowed if DC-HSDPA and
MIMO are simultaneously configured in
use for the UE.
DC-HSDPA with MIMO simultaneously configured in use for the UE
doubles the amount of CQI reporting. UE
sends two consecutive CQI reports: one
for the primary carrier immediately
followed by another one for the secondary carrier. This affects performance of
the CQI reporting reduction.
CPCStreaming2msTTI/S2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Str 2ms
TTI)
Field
Description
Issue 05E
Issue 06
The parameter defines the CQI feedback
cycle for HSDPA when the CQI reporting
is not reduced because of DTX. This is
part of CQI Reporting reduction subfeature.
This parameter is used for streaming when 2 ms TTI is used on E-DCH.
Note! CQI reporting cycles values
bigger than 10ms are not recommended
Note! This parameter value must
be an integer divisor or a multiple of the
parameter S2msUEDTXCycle2 value.
The parameter defines the CQI feedback
cycle for HSDPA when the CQI reporting
is not reduced because of DTX. This is
part of CQI Reporting reduction subfeature.
This parameter is used for streaming when 2 ms TTI is used on E-DCH.
Note! CQI reporting cycles values
bigger than 10ms are not recommended.
Note! This parameter value must
be an integer divisor or a multiple of the
parameter S2msUEDTXCycle2 value.
CPCVoice2msTTI/V2msCQIFeedbackCPC (CQI Feedback Cycle for CPC Voi 2ms TTI)
298
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
The parameter defines the CQI feedback
cycle for HSDPA when the CQI reporting
is not reduced because of DTX. This is
part of CQI Reporting reduction subfeature.
This parameter is used when 2 ms
TTI is used on E-DCH with CS voice over
HSPA feature.
Note! CQI reporting cycles values
bigger than 10ms are not recommended
Note! This parameter value must
be an integer divisor or a multiple of the
parameter V2msUEDTXCycle2 value.
The parameter defines the CQI feedback
cycle for HSDPA when the CQI reporting
is not reduced because of DTX. This is
part of CQI Reporting reduction subfeature.
This parameter is used when 2 ms
TTI is used on E-DCH with CS voice over
HSPA feature.
Note! CQI reporting cycles values
bigger than 10ms are not recommended.
Note! This parameter value must
be an integer divisor or a multiple of the
parameter V2msUEDTXCycle2 value.
DCellVsMIMOPreference (Dual Cell versus MIMO preference)
Field
Description
Issue 05E
Issue 06
Parameter determines whether RNC primarily activates DC-HSDPA or MIMO for
the UE, that supports both DC-HSDPA
and MIMO in case simultaneous usage of
DC-HSDPA and MIMO is not possible.
Parameter determines whether RNC primarily activates DC-HSDPA or MIMO for
the UE, that supports both DC-HSDPA
and MIMO in case simultaneous usage of
DC-HSDPA and MIMO is not possible.
Parameter also determines whether
DB-DC-HSDPA or MIMO is preferred.
HSDPAPeakRateLimitRABMax (HSDPA peak rate limitation to the RAB maximum)
Field
Related parameters
Issue 05E
Issue 06
HSDPAinitialBitrateUL of RNHSPA - If
limitation is active and the RAB maximum
is below the value in HSDPAInitialBitrateUL, HSDPA is not used because no
suitable UL return channel can be
reserved. In that case DCH is used.
HSDPAinitialBitrateUL of WAC - If limitation is active and the RAB maximum is
below the value in HSDPAInitialBitrateUL, HSDPA is not used because no
suitable UL return channel can be
reserved. In that case DCH is used.
HSPANBRValues (HSPA NBR values)
DN70456011
Id:0900d80580a2e11c
Confidential
299
Summary of changes
Field
Related parameters
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
HSPAQoSEnabled of WCEL - This
parameters is relevant if Streaming is in
use in the cell
HSPAQoSEnabled of WCEL - This
parameters is relevant if Streaming is in
use in the cell
QoSPriorityMapping of RNPS - The
system checks that NBR is given just to
uplink, just to downlink or both uplink and
downlink just to priorities that are used by
interactive or background traffic classes
QoSPriorityMapping of RNPS - The
system checks that NBR is given just to
uplink, just to downlink or both uplink and
downlink just to priorities that are used by
interactive or background traffic classes
AARConfigTable of RNHSPA - The
system prevents adding or removing of
NBR if application group mapping is
defined for the SPI in question or SPI in
question is used as target SPI.
MACdflowthroughputRelThr (Low throughput threshold of the MAC-d flow)
Field
Related parameters
Issue 05E
MACdflowthroughputAveWin of
RNHSPA - The sliding measurement
window is defined with the parameter
MACdflowthroughputAveWin.
MACdflowthroughputTimetoTrigger of
RNHSPA - If the result of the throughput
measurement for NRT MAC-d flow is less
than or equal to the threshold, the MACdflowthroughputTimetoTrigger timer is
started.
MACdflowtputStrTtT of RNHSPA - If the
result of the throughput measurement for
streaming MAC-d flow is less than or
equal to the threshold, the MACdflowthroughputTimetoTrigger timer is
started.
Issue 06
MACdflowthroughputTimetoTrigger of
RNHSPA - If the result of the throughput
measurement for NRT MAC-d flow is less
than or equal to the threshold, the MACdflowthroughputTimetoTrigger timer is
started.
MACdflowtputStrTtT of RNHSPA - If the
result of the throughput measurement for
streaming MAC-d flow is less than or
equal to the threshold, the MACdflowthroughputTimetoTrigger timer is
started.
MACdflowthroughputAveWin of WAC The sliding measurement window is
defined with the parameter MACdflowthroughputAveWin.
MACdflowutilStrTtT (Low util time to trigger of MAC-d flow for streaming)
300
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
MACdflowutilRelThr of RNHSPA - If the
result of the throughput measurement is
lower than or equal to the MACdflowutilRelThr, the MACdflowutilStrTimetoTrigger is started. If the result of the
throughput measurement is higher than
the MACdflowutilRelThr, the MACdflowutilStrTimetoTrigger is stopped and
reset. If the MACdflowutilStrTimetoTrigger expires, the number of RLC PDUs in
the transmission windows is checked: If
the sum of the RLC PDUs in the transmission windows of the RBs mapped to
the MAC-d flow equals zero, L2 sends a
low utilisation indication to L3 and resets
the MACdflowutilStrTimetoTrigger. If
there are any RLC PDUs in the transmission windows, L2 keeps checking the
transmission windows until they are
empty or the downlink throughput goes
above MACdflowutilRelThr
MACdflowutilRelThr of WAC - If the result
of the throughput measurement is lower
than or equal to the MACdflowutilRelThr,
the MACdflowutilStrTimetoTrigger is
started. If the result of the throughput
measurement is higher than the MACdflowutilRelThr, the MACdflowutilStrTimetoTrigger is stopped and reset. If the
MACdflowutilStrTimetoTrigger expires,
the number of RLC PDUs in the transmission windows is checked: If the sum of
the RLC PDUs in the transmission
windows of the RBs mapped to the MACd flow equals zero, L2 sends a low utilisation indication to L3 and resets the
MACdflowutilStrTimetoTrigger. If there
are any RLC PDUs in the transmission
windows, L2 keeps checking the transmission windows until they are empty or
the downlink throughput goes above
MACdflowutilRelThr
HSDPAMaxCellChangeRepetition (Max number of repetitive serving HS-DSCH cell
changes)
DN70456011
Id:0900d80580a2e11c
Confidential
301
Summary of changes
Field
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
Description
The parameter determines the maximum
number of repetitive serving HS-DSCH
cell changes during a predefined time
period (see parameter relationships). If
the maximum number of serving HSDSCH cell changes is exceeded, HSDSCH is released. When this HSDPAMaxCellChangeRepetition is set to 0, the
CTS to DCH due to repetitive SCC's is
disabled.
This parameter determines the maximum
number of repetitive serving HS-DSCH
cell changes during a predefined time
period. If the maximum number of serving
HS-DSCH cell changes is exceeded, HSDSCH is released. When this parameter
is set to 0, the CTS to DCH due to repetitive SCC's is disabled.
This parameter is overruled if Fast
HSPA Mobility is enabled in the serving
HS-DSCH cell with the WCEL parameter
FastHSPAMobilityEnabled and the
maximum number of repetitive serving
HS-DSCH cell changes is determined on
cell level with the WCEL parameter HSDPAMaxCellChangeRepetition of the
serving HS-DSCH cell.
The RNHSPA parameter HSDPACellChangeRepetitionTime determines the time period during which the
maximum number of repetitive serving
HS-DSCH cell changes is counted.
Related parameters
HSDPAMobility of RNFC - Parameter
activates the serving HS-DSCH cell
change.
HSDPACellChangeRepetitionTime of
RNHSPA - Parameter determines the
period during which the maximum
number of repetitive serving HS-DSCH
cell changes is counted.
MaxBitRateNRTMACDFlow (Maximum bit rate of NRT MAC-d flow)
302
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
DN70456011
Summary of changes
Id:0900d80580a2e11c
Confidential
303
Summary of changes
Field
Description
304
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
The parameter can be used to restrict the
maximum bit rate of NRT MAC-d flow.
The bit rate used in the reservation of the
resources for the MAC-d flow is the
minimum value of maximum bit rate
based on UE capability, maximum bit rate
of the RAB, activated HSDPA bit rate
features and the value of this parameter.
This parameter does not limit the
maximum instantaneous bit rate on air
interface. Value of the parameter is
compared to the user bit rate of the NRT
MAC-d flow excluding MAC-hs header,
RLC header and padding (parameter
value includes RLC PDU payload only).
Maximum value of this parameter
depends on what are the features
licenced for the RNC.
- If there is no licence for the feature
HSDPA 15 Codes (10 codes or 15 codes
licence), then the maximum value is 3456
kbps.
- If there is licence for the feature
HSDPA 15 Codes (10 codes or 15 codes
licence), then the maximum value is 6784
kbps.
- If there is licence for the feature
HSDPA 15 Codes (10 codes or 15 codes
licence)and the feature HSDPA 10Mbps
per User, then the maximum value is
9600 kbps.
- If there is licence for the feature
HSDPA 15 Codes (10 codes or 15 codes
licence) and the feature HSDPA 14Mbps
per User, then the maximum value is
13440 kbps.
- If there is licence for the feature
HSDPA 15 Codes (10 codes or 15 codes
licence) and the feature HSDPA 64QAM,
then the maximum value is 20992 kbps.
- If there is licence for the feature
MIMO, then the maximum value is 27776
kbps.
- If there is licence for MIMO and
HSDPA 64QAM, then the maximum
value is 41984 kbps.
- If there is licence for the feature DCHSDPA, then the maximum value is
41984 kbps.
- If there is licence for both DCHSDPA and MIMO, then the maximum
value is 55552 kbps.
Id:0900d80580a2e11c
- If there is licence for both DCConfidential
HSDPA, MIMO and HSDPA 64QAM,
then the maximum value is 83968 kbps.
The parameter can be used to restrict the
maximum bit rate of NRT MAC-d flow.
The bit rate used in the reservation of the
resources for the MAC-d flow is the
minimum value of maximum bit rate
based on UE capability, maximum bit rate
of the RAB, activated HSDPA bit rate
features and the value of this parameter.
This parameter does not limit the
maximum instantaneous bit rate on air
interface. Value of the parameter is
compared to the user bit rate of the NRT
MAC-d flow excluding MAC-hs header,
RLC header and padding (parameter
value includes RLC PDU payload only).
Maximum value of this parameter
depends on what are the features
licensed for the RNC.
- If there is no license for the feature
HSDPA 15 Codes (10 codes or 15 codes
license), then the maximum value is 3456
kbps.
- If there is license for the feature
HSDPA 15 Codes (10 codes or 15 codes
license), then the maximum value is 6784
kbps.
- If there is license for the feature
HSDPA 15 Codes (10 codes or 15 codes
license)and the feature HSDPA 10Mbps
per User, then the maximum value is
9600 kbps.
- If there is license for the feature
HSDPA 15 Codes (10 codes or 15 codes
license) and the feature HSDPA 14Mbps
per User, then the maximum value is
13440 kbps.
- If there is license for the feature
HSDPA 15 Codes (10 codes or 15 codes
license) and the feature HSDPA 64QAM,
then the maximum value is 20992 kbps.
- If there is license for the feature
MIMO, then the maximum value is 27776
kbps.
- If there is license for MIMO and
HSDPA 64QAM, then the maximum
value is 41984 kbps.
- If there is license for the feature DCHSDPA, then the maximum value is
41984 kbps.
- If there is license for both DCHSDPA and MIMO, then the maximum
value is 55552 kbps.
DN70456011
- If there is license for both DCHSDPA, MIMO and HSDPA 64QAM,
then the maximum value is 83968 kbps.
Radio Network Parameters in Flexi Direct
Summary of changes
ATOSRBsOnHSPA (Offset for activation time of SRBs on HSPA)
Field
Description
Issue 05E
Issue 06
This parameter defines activation time
when the SRBs mapped on E-DCH/HSDSCH is in use. Connection Frame
Number (CFN) is used in NBAP and RRC
messages, when a radio link is reconfigured. It is used to indicate the activation
time of the reconfiguration, and it is set by
the PS. The CFN, which is set to the "activation time" field in L3 messages, is (the
CFN provided by FP + (ATOSRBsOnHSPA/10)) mod 256.
This parameter determines the offset
value that is added to the activation time,
which RNC has produced internally for a
synchronised radio link handling procedure. Connection Frame Number (CFN)
which is set to the "activation time" fields
of the NBAP and RRC messages indicate
the activation time of the reconfiguration.
Value of the CFN is produced by adding
(modulo 256) the value of this parameter
to the current CFN provided by the Frame
Protocol (FP). This parameter is applicable when the SRBs are mapped on EDCH/HS-DSCH.
This parameter is overruled if Fast
HSPA Mobility is enabled in the serving
HS-DSCH cell with the WCEL parameter
FastHSPAMobilityEnabled and the activation time offset is determined on cell
level with the WCEL parameter
ATOSRBsOnHSPA of the serving HSDSCH cell.
UPResAllocInCellDCHWait (Retry time for u-plane resource allocation in Cell_DCH)
DN70456011
Id:0900d80580a2e11c
Confidential
305
Summary of changes
Field
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
Description
This timer defines the time in case of
resource shortage/congestion where
DCH/DCH resource allocation reattempts should succeed.
The UPResAllocInCellDCHWait
timer is set if the dedicated channel allocation tried for Packet Switched data
fails, because of the resource congestion.
Timer is used over the whole
resource allocation scenario (radio
resources, DMCU-resources, radio link
setup (BTS HW-resources) and AAL2setup (transmission resources)), and
thus the timer may expire in a different
phase of the ongoing allocation procedure or outside of the scenario (RNC is
waiting the next UL/DL capacity request
from UE/IUG).
If the timer expires the packet scheduler makes a decision for the UE state
transition to Cell_FACH or
Cell/URA_PCH or tot decides that the UE
will stay in Cell_DCH state.
The value 255 means that the adjustable user plane resource allocation retry
timer is not in use and switching the UE
to Cell_FACH (or Cell/URA_PCH) state
is not used.
In case of CS + PS- multiservice connection, the UE is kept in Cell_DCH state
as long as the UL/DL capacity request is
being received.
This timer defines the time in case of
resource shortage/congestion where
DCH/DCH resource allocation reattempts should succeed.
The UPResAllocInCellDCHWait
timer is set if the dedicated channel allocation tried for Packet Switched data
fails, because of the resource congestion.
Timer is used over the whole
resource allocation scenario (radio
resources, DMCU-resources, radio link
setup (BTS HW-resources) and AAL2setup (transmission resources)), and
thus the timer may expire in a different
phase of the ongoing allocation procedure or outside of the scenario (RNC is
waiting the next UL/DL capacity request
from UE/IUG).
If the timer expires the packet scheduler makes a decision for the UE state
transition to Cell_FACH or
Cell/URA_PCH or tot decides that the UE
will stay in Cell_DCH state.
The value 255 means that the adjustable user plane resource allocation retry
timer is not in use and switching the UE
to Cell_FACH (or Cell/URA_PCH) state
is not used.
In case of CS + PS- multiservice connection, the UE is kept in Cell_DCH state
as long as the UL/DL capacity request is
being received.
UPResAllocInCellDCHWait is recommended to be greater than TrafVolPendingTimeDL and TrafVolPendingTimeUL
in all WAC instances.
Related parameters
TrafVolPendingTimeDL of RNPS - Timer
TrafVolPendingTimeDL should be
shorter than UPResAllocInCellDCHWait
timer.
TrafVolPendingTimeUL of RNPS - Timer
TrafVolPendingTimeUL should be
shorter than UPResAllocInCellDCHWait
timer.
306
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
HSDPACellChangeRepetitionTime (Window for max repetitive serving HS-DSCH cell
changes)
Field
Issue 05E
Description
The parameter determines the time
period for calculation of the maximum
number of repetitive serving HS-DSCH
cell changes.
Related parameters
HSDPAMobility of RNFC - Parameter
activates the serving HS-DSCH cell
change.
Issue 06
This parameter determines the time
period for calculation of the maximum
number of repetitive serving HS-DSCH
cell changes.
The RNHSPA parameter (or the corresponding WCEL parameter) HSDPAMaxCellChangeRepetition determines
the maximum number of repetitive
serving HS-DSCH cell changes allowed
during the time period.
HSDPAMaxCellChangeRepetition of
RNHSPA - Parameter determines the
maximum number of repetitive serving
HS-DSCH cell changes allowed during
the time period.
RNMOBI
HSDPACPICHAveWindow (Averaging window of the CPICH Ec/No measurement)
Field
Issue 05E
Issue 06
Description
This parameter determines the averaging
window for the periodical CPICH Ec/No
measurement reporting, which is used as
a criterion for the serving HS-DSCH cell
change procedure. Averaging is
executed in the RNC.
This parameter determines the averaging
window for the periodical CPICH Ec/No
measurement reporting, which is used as
a criterion for the serving HS-DSCH cell
change procedure. Averaging is
executed in the RNC.
This parameter is overruled if Fast
HSPA Mobility is enabled in the serving
HS-DSCH cell with the WCEL parameter
FastHSPAMobilityEnabled and the averaging window for the periodical CPICH
Ec/No measurement reporting is determined on cell level with the WCEL
parameter HSDPACPICHAveWindow of
the serving HS-DSCH cell.
Related parameters
HSDPAMobility of RNFC - Parameter is
applicable if the HSDPA serving cell
change is enabled.
BlindGsmHoCS (Blind GSM handover for CS RAB)
DN70456011
Id:0900d80580a2e11c
Confidential
307
Summary of changes
Field
Interfaces
Radio Network Parameters in Flexi Direct
Issue 05E
RAC<->IADA, EM<->IADA, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC
DirectPchDchCS (Cell/URA_PCH to Cell_DCH transition due to CS call)
Field
Interfaces
Issue 05E
RAC<->IADA, EM<->IADA, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC
CUCEcNoThresholdCSEHO (CPICH Ec/No Threshold Value For CUC Usage in
CSEHO)
Field
Interfaces
Issue 05E
RAC<->IADA, EM<->IADA, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC
HSDPAServCellWindow (CPICH Ec/No window for serving HS-DSCH cell selection)
308
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
This parameter determines the maximum
allowed difference between the best cell
and the serving HS-DSCH cell. The
window is relative to the best cell in the
active set. If the serving HS-DSCH cell
change is outside of the window, serving
HS-DSCH cell change procedure is initiated. The measured quantity is CPICH
Ec/No, which is received periodically
from the UE.
This parameter determines the maximum
allowed difference between the CPICH
Ec/No of the best active set cell and the
CPICH Ec/No of the serving HS-DSCH
cell. If the difference between the
averaged CPICH Ec/No values exceeds
the value of this parameter, serving HSDSCH cell change procedure is initiated.
This parameter is overruled if Fast
HSPA Mobility is enabled in the serving
HS-DSCH cell with the WCEL parameter
FastHSPAMobilityEnabled and the
maximum allowed difference between
the best active set cell and the serving
HS-DSCH cell is determined on cell level
with the WCEL parameter HSDPAServCellWindow of the serving HS-DSCH
cell.
The RNMOBI parameters HSDPACPICHReportPeriod and HSDPACPICHAveWindow (or the
corresponding WCEL parameters) determine the reporting period of the periodical
intra-frequency CPICH Ec/No measurement, which is used as a criterion for the
serving HS-DSCH cell change procedure, and the averaging window for the
periodical CPICH Ec/No measurement
reports respectively.
Related parameters
HSDPAMobility of RNFC - Parameter is
applicable if the HSDPA serving cell
change is enabled.
HSPADRNCSIRErrorOffset of RNMOBI SRNC applies DRNC offset in the case
HSPA inter-RNC Cell Change.
Related features
HSDPA (optional) AND HSDPA Serving
Cell Change (optional) OR HSDPA
(optional) AND HSDPA Serving Cell
Change (optional) AND HSPA InterRNC Cell Change (optional)
HSDPA Serving Cell Change (optional)
PagingRoleType (Current Role of FD-BTS)
Field
Parameter Name
DN70456011
Issue 05E
Current Role of I-BTS
Id:0900d80580a2e11c
Confidential
Issue 06
Current Role of FD-BTS
309
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
This parameter tells whether I-BTS is a
Paging Master (PM) or a Paging Standby
(PS) or a normal I-BTS. If this parameter
is configured to PM or PS then I-BTS distributes the idle paging messages
received from CN in the paging group.
This parameter tells whether FD-BTS is a
Paging Master (PM) or a Paging Standby
(PS) or a normal FD-BTS. If this parameter is configured to PM or PS then FDBTS distributes the idle paging messages
received from CN in the paging group.
Range and step
0 (Normal I-BTS), 1 (Paging Master), 2
(Paging Standby)
0 (Normal FD-BTS), 1 (Paging Master), 2
(Paging Standby)
Default value notes
Normal I-BTS
Normal FD-BTS
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC
PagingGroupList (List of FD-BTS in paging group)
Field
Issue 05E
Issue 06
Parameter Name
List of I-BTS in paging group
List of FD-BTS in paging group
Description
This parameter lists the I-BTS’s that are
part of the paging group, to which the
current I-BTS belongs. The list is used by
the I-BTS defined as Paging master or
Paging standby in the paging group. The
own RNC-ID of the current I-BTS can be
included in the PagingGroupList.
This parameter lists the FD-BTS’s that
are part of the paging group, to which the
current FD-BTS belongs. The list is used
by the FD-BTS defined as Paging master
or Paging standby in the paging group.
The own RNC-ID of the current FD-BTS
can be included in the PagingGroupList.
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC
MaxBLHOAttempt (Maximum Number of BLHO Attempts)
Field
Issue 05E
Issue 06
Description
This parameter describes the maximum
number of inter-system blind handover
attempts which I-HSPA Adapter can
perform for successful handover of a UE
towards IR network.
This parameter describes the maximum
number of inter-system blind handover
attempts which FD-RNC can perform for
successful handover of a UE towards IR
network.
Default value notes
I-HSPA Adapter can perform a total of
one IR BLHO handover attempts for UE,
for a successful IR BLHO.
FD-RNC can perform a total of one IR
BLHO handover attempts for UE, for a
successful IR BLHO.
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC
HSDPACellChangeMinInterval (Minimum interval between serving HS-DSCH cell
changes)
310
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
Parameter determines the minimum
interval between serving HS-DSCH cell
changes due to CPICH Ec/No window
between the best cell and the serving HSDSCH cell. Timer is started after every
successfully executed serving HS-DSCH
cell change. During the time period,
serving HS-DSCH cell changes caused
by the periodical CPICH Ec/No reporting
are forbidden. If the value of the parameter is set to 0, serving HS-DSCH cell
changes are not restricted.
This parameter determines the minimum
interval between serving HS-DSCH cell
changes when the periodical CPICH
Ec/No reporting indicates that the
maximum allowed difference between
the CPICH Ec/No of the best active set
cell and the CPICH Ec/No of the serving
HS-DSCH cell is exceeded. Timer is
started after every successfully executed
serving HS-DSCH cell change. During
the time period, serving HS-DSCH cell
changes triggered by the periodical
CPICH Ec/No reporting are forbidden. If
the value of this parameter is set to 0,
serving HS-DSCH cell changes are not
restricted.
This parameter is overruled if Fast
HSPA Mobility is enabled in the serving
HS-DSCH cell with the WCEL parameter
FastHSPAMobilityEnabled and the
minimum interval between serving HSDSCH cell changes is determined on cell
level with the WCEL parameter HSDPACellChangeMinInterval of the serving
HS-DSCH cell.
Related parameters
HSDPAMobility of RNFC - Parameter is
applicable if the HSDPA serving cell
change is enabled.
PagingGroupList/PgRncId (Paging Group member I-BTS RNC-ID)
Field
Issue 05E
Issue 06
Description
Parameter defines the RNC-ID of
members in a Paging Group.
This parameter defines the RNC-ID of
members in a Paging Group.
Interfaces
RAC<->IADA, EM<->IADA, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC
IBTSRabCombSupport (RAB Combinations Supported by FD-BTS)
Field
Issue 05E
Issue 06
Parameter Name
RAB Combinations Supported by IBTS
RAB Combinations Supported by FDBTS
Description
This parameter defines all the single and
multi- rab combinations that are supported by I-BTS.
This parameter defines all the single and
multi- rab combinations that are supported by FD-BTS.
DN70456011
Id:0900d80580a2e11c
Confidential
311
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Default value notes
Issue 05E
Issue 06
Only Single PS NRT RAB is supported by
I-BTS.
Only Single PS NRT RAB is supported by
FD-BTS.
HSDPACPICHReportPeriod (Reporting period of the CPICH Ec/No measurement)
Field
Issue 05E
Issue 06
Description
This parameter determines the reporting
period of the CPICH Ec/No measurement, which is used as a criterion for the
serving HS-DSCH cell change procedure.
This parameter determines the reporting
period of the CPICH Ec/No measurement, which is used as a criterion for the
serving HS-DSCH cell change procedure.
This parameter is overruled if Fast
HSPA Mobility is enabled in the serving
HS-DSCH cell with the WCEL parameter
FastHSPAMobilityEnabled and the
reporting period of the CPICH Ec/No
measurement is determined on cell level
with the WCEL parameter HSDPACPICHReportPeriod of the serving
HS-DSCH cell.
Related parameters
HSDPAMobility of RNFC - Parameter is
applicable if the HSDPA serving cell
change is enabled.
RNPS
TrafVolThresholdDLHigh (Downlink traffic volume measurement high threshold)
312
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
TrafVolThresholdDLLow of WCEL Defines the threshold of data in the RLC
buffers that triggers the downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in
Cell_FACH state.
TrafVolThresholdDLLow of WCEL Defines the threshold of data in the RLC
buffers that triggers the downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in
Cell_FACH state.
InitialBitRateDL of WCEL - Defines the
minimum allowed bit rate in downlink that
can be allocated by the PS.
InitialBitRateDL of WCEL - Defines the
minimum allowed bit rate in downlink that
can be allocated by the PS.
TrafVolPendingTimeDL of RNPS Defines the period of time during which it
is forbidden to send any new downlink
capacity requests with the same RB id,
even if the triggering condition is fulfilled
again
TrafVolThresholdDLHighBitRate of
RNPS - Defines the threshold of data in
the RLC buffer of RB which triggers
downlink traffic volume measurement
report (capacity request) on MAC-d of
RNC, when UE is in a Cell_DCH state
and DCH is allocated for the radio bearer.
TrafVolThresholdDLHighBitRate of
RNPS - Defines the threshold of data in
the RLC buffer of RB which triggers
downlink traffic volume measurement
report (capacity request) on MAC-d of
RNC, when UE is in a Cell_DCH state
and DCH is allocated for the radio bearer.
TrafVolTimeToTriggerDL of RNPS Defines the period of time between the
timing of event detection and the timing of
sending a downlink capacity request.
TrafVolTimeToTriggerDL of RNPS Defines the period of time between the
timing of event detection and the timing of
sending a downlink capacity request.
TrafVolPendingTimeDL of WAC Defines the period of time during which it
is forbidden to send any new downlink
capacity requests with the same RB id,
even if the triggering condition is fulfilled
again
TrafVolTimeToTriggerDL (Downlink traffic volume measurement time to trigger)
DN70456011
Id:0900d80580a2e11c
Confidential
313
Summary of changes
Field
Related parameters
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
TrafVolThresholdDLLow of WCEL Defines the threshold of data in the RLC
buffers that triggers the downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in
Cell_FACH state.
TrafVolThresholdDLLow of WCEL Defines the threshold of data in the RLC
buffers that triggers the downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in
Cell_FACH state.
TrafVolPendingTimeDL of RNPS Defines the period of time during which it
is forbidden to send any new downlink
capacity requests with the same RB id,
even if the triggering condition is fulfilled
again
TrafVolThresholdDLHigh of RNPS Defines the threshold of data in the RLC
buffer which triggers downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in a
Cell_DCH state and the initial bit rate
DCH is allocated for the radio bearer.
TrafVolThresholdDLHigh of RNPS Defines the threshold of data in the RLC
buffer which triggers downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in a
Cell_DCH state and the initial bit rate
DCH is allocated for the radio bearer.
TrafVolPendingTimeDL of WAC Defines the period of time during which it
is forbidden to send any new downlink
capacity requests with the same RB id,
even if the triggering condition is fulfilled
again
DCHUtilLowerDowngradeThrBitRate (Lower downgrade threshold)
314
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
DN70456011
Summary of changes
Id:0900d80580a2e11c
Confidential
315
Summary of changes
Field
Description
316
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
This parameter defines the target lower
downgrade bit rate and with the DCHUtilBelowDowngradeThr parameter the
lower throughput measurement threshold
for the allocated up/down link NRT DCH.
The target lower downgrade bit rate
is defined as a number of bits per second.
The bit rate of the downgrade lower
threshold that is used in the "lower"
throughput measurement is DCHUtilLowerDowngradeThrXX - DCHUtilLowerDowngradeThrXX *
DCHUtilBelowDowngradeThr. The "XX"
in the "DCHUtilLowerDowngradeThrXX"
parameter represents the allocated NRT
DCH bit rate.
The lower throughput measurement
measures the number of all bits transmitted during the sliding measurement
window. The sliding measurement
window is defined by the DCHUtilLowerAveWinBitRate RNP parameter. If the
result of the upper throughput measurement falls below the lower bit rate threshold, the time to trigger supervision is
started. Time to trigger can be managed
by the DCHUtilLowerTimeToTriggerBitRate RNP parameter. If the result of the
throughput measurement has been
below the threshold for the time to trigger
supervision period, the UL/DL NRT DCH
utilisation is detected to be below the
lower bit rate threshold and the UL/DL
NRT DCH bit rate is downgraded to the
target lower downgrade bit rate.
The threshold is defined separately
for each bit rate.
Default values:
- 8 kbps for the NRT user plane rate
whose bit rate is 32 kbps
- 8 kbps for the NRT user plane rate
whose bit rate is 64 kbps
- 16 kbps for the NRT user plane rate
whose bit rate is 128 kbps
- 32 kbps for the NRT user plane rate
whose bit rate is 256 kbps
- 64 kbps for the NRT user plane rate
whose bit rate is 384 kbps
The lower threshold values are
chosen such that if the bit rate is about
25% of the allocated bit rate, the bit rate
is downgraded to this bit rate.
Id:0900d80580a2e11c
With these parameter settings (and
Confidential
other throughput base optimisation of PS
algorithm parameters), the slow start
This parameter defines the target lower
downgrade bit rate and with the DCHUtilBelowDowngradeThr parameter the
lower throughput measurement threshold
for the allocated up/down link NRT DCH.
The target lower downgrade bit rate
is defined as a number of bits per second.
The bit rate of the downgrade lower
threshold that is used in the "lower"
throughput measurement is DCHUtilLowerDowngradeThrXX - DCHUtilLowerDowngradeThrXX *
DCHUtilBelowDowngradeThr / 100. The
"XX" in the "DCHUtilLowerDowngradeThrXX" parameter represents the allocated NRT DCH bit rate.
The lower throughput measurement
measures the number of all bits transmitted during the sliding measurement
window. The sliding measurement
window is defined by the DCHUtilLowerAveWinBitRate RNP parameter. If the
result of the upper throughput measurement falls below the lower bit rate threshold, the time to trigger supervision is
started. Time to trigger can be managed
by the DCHUtilLowerTimeToTriggerBitRate RNP parameter. If the result of the
throughput measurement has been
below the threshold for the time to trigger
supervision period, the UL/DL NRT DCH
utilisation is detected to be below the
lower bit rate threshold and the UL/DL
NRT DCH bit rate is downgraded to the
target lower downgrade bit rate.
The threshold is defined separately
for each bit rate.
Default values:
- 8 kbps for the NRT user plane rate
whose bit rate is 32 kbps
- 8 kbps for the NRT user plane rate
whose bit rate is 64 kbps
- 16 kbps for the NRT user plane rate
whose bit rate is 128 kbps
- 32 kbps for the NRT user plane rate
whose bit rate is 256 kbps
- 64 kbps for the NRT user plane rate
whose bit rate is 384 kbps
The lower threshold values are
chosen such that if the bit rate is about
25% of the allocated bit rate, the bit rate
is downgraded to this bit rate.
DN70456011
With these parameter settings (and
other throughput base optimisation of PS
algorithm parameters), the slow start
Radio Network Parameters in Flexi Direct
Summary of changes
CrQueuingTimeDL (Maximum downlink capacity request queuing time)
Field
Related parameters
Issue 05E
Issue 06
LHOWinSizeONCapaReqRejRate of
WCEL - The value of the parameter has
to be equal to or lower than LHOWinSizeONCapaReqRejRate (when measurement is active).
LHOWinSizeONCapaReqRejRate of
WCEL - The value of the parameter has
to be equal to or lower than LHOWinSizeONCapaReqRejRate (when measurement is active).
CrQueuingTimeUL of RNPS - The corre- CrQueuingTimeUL of RNPS - The corresponding uplink parameter.
sponding uplink parameter.
TrafVolPendingTimeDL of RNPS CrQueuingTimeDL parameter is related
to the parameter TrafVolPendingTimeDL, which define the time between
consecutive capacity requests.
TrafVolPendingTimeDL of WAC CrQueuingTimeDL parameter is related
to the parameter TrafVolPendingTimeDL, which define the time between
consecutive capacity requests.
CrQueuingTimeUL (Maximum uplink capacity request queuing time)
Field
Related parameters
Issue 05E
Issue 06
LHOWinSizeONCapaReqRejRate of
WCEL - The value of the parameter has
to be equal to or lower than LHOWinSizeONCapaReqRejRate (when measurement is active).
LHOWinSizeONCapaReqRejRate of
WCEL - The value of the parameter has
to be equal to or lower than LHOWinSizeONCapaReqRejRate (when measurement is active).
CrQueuingTimeDL of RNPS - The corre- CrQueuingTimeDL of RNPS - The corresponding downlink parameter.
sponding downlink parameter.
TrafVolPendingTimeUL of RNPS CrQueuingTimeUL parameter is related
to the parameter TrafVolPendingTimeUL, which define the time between
consecutive capacity requests.
TrafVolPendingTimeUL of WAC CrQueuingTimeUL parameter is related
to the parameter TrafVolPendingTimeUL, which define the time between
consecutive capacity requests.
ActivationTimeOffset (Offset for activation time)
DN70456011
Id:0900d80580a2e11c
Confidential
317
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
Parameter defines the offset value that is
added to the activation time, which RNC
has produced internally for a synchronised radio link handling procedure. Connection Frame Number (CFN) which is
set to the "activation time" fields of the
NBAP and RRC messages indicate the
activation time of the reconfiguration.
Value of the CFN is produced by adding
(modulo 256) the sum of the RRC
message length and the SRB bit rate
dependant calculatory offset value and
the value of this parameter to the CFN
provided by FP. Activation time offset
represents the AM RLC retransmissions
of the SRB and the processing delay of
RNC and BTS. Parameter is applicable,
if the DL SL is transferred in the DCH.
This parameter determines the offset
value that is added to the activation time,
which RNC has produced internally for a
synchronised radio link handling procedure. Connection Frame Number (CFN)
which is set to the "activation time" fields
of the NBAP and RRC messages indicate
the activation time of the reconfiguration.
Value of the CFN is produced by adding
(modulo 256) the sum of the RRC
message length and the calculated SRB
bit rate dependent offset value, and the
value of this parameter to the current
CFN provided by the Frame Protocol
(FP). Activation time offset represents the
AM RLC retransmissions of the SRB and
the processing delay of RNC and BTS.
This parameter is applicable when the DL
SL is mapped on DCH.
This parameter is overruled if Fast
HSPA Mobility is enabled in the active set
cell with the WCEL parameter FastHSPAMobilityEnabled and the activation
time offset is determined on cell level with
the WCEL parameter ActivationTimeOffset of the active set cell.
Default value
300
500
RoleSwitchActAdjOffset (Role Switch activation adjustment offset)
Field
Interfaces
Issue 05E
IADA<->RAC, EM<->IADA, RACApp<>RAC
Issue 06
RNC<->RAC, EM<->RNC, RACApp<>RAC
TrafVolThresholdULHigh (Uplink traffic volume measurement high threshold)
318
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
InitialBitRateUL of WCEL - Defines the
minimum allowed bit rate in uplink that
can be allocated by the PS
InitialBitRateUL of WCEL - Defines the
minimum allowed bit rate in uplink that
can be allocated by the PS
TrafVolPendingTimeUL of RNPS Defines the period of time during which it
is forbidden to send any new traffic
volume measurement reports with the
same measurement ID, even if the triggering condition is fulfilled again.
TrafVolThresholdULHighBitRate of
RNPS - Defines the threshold of data in
RLC buffer of RB which triggers the
uplink traffic volume measurement report
when the UE is in a Cell_DCH state and
DCH is allocated for the radio bearer.
TrafVolThresholdULHighBitRate of
RNPS - Defines the threshold of data in
RLC buffer of RB which triggers the
uplink traffic volume measurement report
when the UE is in a Cell_DCH state and
DCH is allocated for the radio bearer.
TrafVolTimeToTriggerUL of RNPS Defines the period of time between the
timing of event detection and the timing of
sending a traffic volume measurement
report.
TrafVolThresholdULLow of RNPS Defines the threshold of data in the RLC
buffers that triggers the uplink traffic
volume measurement report, when the
UE is in Cell_FACH state.
TrafVolPendingTimeUL of WAC Defines the period of time during which it
is forbidden to send any new traffic
volume measurement reports with the
same measurement ID, even if the triggering condition is fulfilled again.
TrafVolTimeToTriggerUL of RNPS Defines the period of time between the
timing of event detection and the timing of
sending a traffic volume measurement
report.
TrafVolThresholdULLow of WAC Defines the threshold of data in the RLC
buffers that triggers the uplink traffic
volume measurement report, when the
UE is in Cell_FACH state.
TrafVolTimeToTriggerUL (Uplink traffic volume measurement time to trigger)
DN70456011
Id:0900d80580a2e11c
Confidential
319
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Related parameters
Issue 05E
TrafVolPendingTimeUL of RNPS Defines the period of time during which it
is forbidden to send any new traffic
volume measurement reports with the
same measurement ID, even if the triggering condition is fulfilled again
TrafVolThresholdULHigh of RNPS Defines the threshold of data in RLC
buffer which triggers the uplink traffic
volume measurement report when the
UE is in a Cell_DCH state and bit rate
higher than 16 kbps is allocated for the
radio bearer
TrafVolThresholdULLow of RNPS Defines the threshold of data in the RLC
buffers that triggers the uplink traffic
volume measurement report, when the
UE is in Cell_FACH state.
Issue 06
TrafVolThresholdULHigh of RNPS Defines the threshold of data in RLC
buffer which triggers the uplink traffic
volume measurement report when the
UE is in a Cell_DCH state and bit rate
higher than 16 kbps is allocated for the
radio bearer
TrafVolPendingTimeUL of WAC Defines the period of time during which it
is forbidden to send any new traffic
volume measurement reports with the
same measurement ID, even if the triggering condition is fulfilled again
TrafVolThresholdULLow of WAC Defines the threshold of data in the RLC
buffers that triggers the uplink traffic
volume measurement report, when the
UE is in Cell_FACH state.
RNRLC
AMRLCMaximumBufferUE/AMRLCMaximumBufferUE1k (AM RLC maximum buffer
allocation for UE capability 1000)
Field
Description
Issue 05E
Issue 06
This parameter defines the maximum AM
RLC buffer of the UE, which has reported
the value of 1000 kBytes for its nominal
Total RLC AM and MAC-hs/MAC-ehs
buffer size. This parameter allows to
define the maximum buffer smaller than
the reported value of UE RLC buffer. In
certain cases the reported value of UE
RLC buffer is unneccessary big and a
smaller buffer is enough to store data
received during one L2 TTI. Therefore, it
is reasonable to define smaller maximum
buffer size in these cases.
This parameter defines the maximum AM
RLC buffer of the UE, which has reported
the value of 1000 kBytes for its nominal
Total RLC AM and MAC-hs/MAC-ehs
buffer size. This parameter allows to
define the maximum buffer smaller than
the reported value of UE RLC buffer. In
certain cases the reported value of UE
RLC buffer is unnecessary big and a
smaller buffer is enough to store data
received during one L2 TTI. Therefore, it
is reasonable to define smaller maximum
buffer size in this case.
AMRLCMaximumBufferUE/AMRLCMaximumBufferUE1150 (AM RLC maximum buffer
allocation for UE capability 1150)
320
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
This parameter defines the maximum AM
RLC buffer of the UE, which has reported
the value of 1150 kBytes for its nominal
Total RLC AM and MAC-hs/MAC-ehs
buffer size. This parameter allows to
define the maximum buffer smaller than
the reported value of UE RLC buffer. In
certain cases the reported value of UE
RLC buffer is unneccessarily big and a
smaller buffer is enough to store data
received during one L2 TTI. Therefore, it
is reasonable to define smaller maximum
buffer size in these case.
This parameter defines the maximum AM
RLC buffer of the UE, which has reported
the value of 1150 kBytes for its nominal
Total RLC AM and MAC-hs/MAC-ehs
buffer size. This parameter allows to
define the maximum buffer smaller than
the reported value of UE RLC buffer. In
certain cases the reported value of UE
RLC buffer is unnecessarily big and a
smaller buffer is enough to store data
received during one L2 TTI. Therefore, it
is reasonable to define smaller maximum
buffer size in this case.
AMRLCMaximumBufferUE/AMRLCMaximumBufferUE1250 (AM RLC maximum buffer
allocation for UE capability 1250)
Field
Description
Issue 05E
Issue 06
This parameter defines the maximum AM
RLC buffer of the UE, which has reported
the value of 1250 kBytes for its nominal
Total RLC AM and MAC-hs/MAC-ehs
buffer size. This parameter allows to
define the maximum buffer smaller than
the reported value of UE RLC buffer. In
certain cases the reported value of UE
RLC buffer is unneccessarily big and a
smaller buffer is enough to store data
received during one L2 TTI. Therefore, it
is reasonable to define smaller maximum
buffer size in these case.
This parameter defines the maximum AM
RLC buffer of the UE, which has reported
the value of 1250 kBytes for its nominal
Total RLC AM and MAC-hs/MAC-ehs
buffer size. This parameter allows to
define the maximum buffer smaller than
the reported value of UE RLC buffer. In
certain cases the reported value of UE
RLC buffer is unnecessarily big and a
smaller buffer is enough to store data
received during one L2 TTI. Therefore, it
is reasonable to define smaller maximum
buffer size in this case.
AMRLCOnDCHOfNRTPS/AMRLCOnDCHOfNRTPSMaxRST (AM RLC MaxRST transmissions for PS NRT with DCH)
Field
Default value
Issue 05E
12
Issue 06
24
AMRLCOnEDCHOfNRTPS/AMRLCOnEDCHOfNRTPSMaxRST (AM RLC maxRST
transmissions for PS NRT with E-DCH)
Field
Default value
Issue 05E
12
Issue 06
24
AMRLCOnHSDSCHOfNRTPS/AMRLCOnHSDSCHOfNRTPSMaxRST (AM RLC
maxRST transmissions for PS NRT with HS-DSCH)
DN70456011
Id:0900d80580a2e11c
Confidential
321
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Default value
Issue 05E
12
Issue 06
24
AMRLCOnDCHOfNRTPS/AMRLCOnDCHOfNRTPSPollPDU (AM RLC period
Poll_PDU for PS NRT with DCH)
Field
Description
Issue 05E
Issue 06
This parameter defines the minimum
value of the RLC protocol parameter
Poll_PDU for the AM RLC entity of the PS
interactive and background radio bearers
when data is transferred with DCH. The
parameter defines how often the sender
polls the receiver in accordance with the
activation of the poll trigger 'polling every
Poll_PDU PDU'. The value of the parameter is expressed in relation to the size of
the allocated transmission window for the
AMR RLC entity. It is transformed into the
corresponding number for the AMD
PDUs by rounding it up to the closest
integer and configuring it to the AM RLC
entity. Poll_PDU can be set to a bigger
value with other means. The value is configured as such to the RLC entity of the
RNC. The value is signalled to the RLC
entity of the UE rounded up to the closest
value or down to the maximum value
allowed in the RRC signalling. The trigger
is applied if it has been activated with the
"AM RLC status report triggers for PS
NRT with DCH" parameter.
This parameter defines the minimum
value of the RLC protocol parameter
Poll_PDU for the AM RLC entity of the PS
interactive and background radio bearers
when data is transferred with DCH. The
parameter defines how often the sender
polls the receiver in accordance with the
activation of the poll trigger 'polling every
Poll_PDU PDU'. The value of the parameter is expressed in relation to the size of
the allocated transmission window for the
AM RLC entity. It is transformed into the
corresponding number for the AMD
PDUs by rounding it up to the closest
integer and configuring it to the AM RLC
entity. Poll_PDU can be set to a bigger
value with other means. The value is configured as such to the RLC entity of the
RNC. The value is signalled to the RLC
entity of the UE rounded up to the closest
value or down to the maximum value
allowed in the RRC signalling. The trigger
is applied if it has been activated with the
"AM RLC status report triggers for PS
NRT with DCH" parameter.
AMRLCOnDCHOfNRTPS/AMRLCOnDCHOfNRTPSFilterReTX (AM RLC retransmission filter for PS NRT with DCH)
322
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
AMRLCRespTimeDCH10 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 10 ms.
AMRLCRespTimeDCH10 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 10 ms.
AMRLCRespTimeDCH20 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 20 ms.
AMRLCRespTimeDCH20 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 20 ms.
AMRLCRespTimeDCH40 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 40 ms.
AMRLCRespTimeDCH40 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 40 ms.
AMRLCRespTimeDCHRevHSDSCH of
RNRLC - defines the reference AM RLC
RTT value when the reverse channel is
the HS-DSCH.
AMRLCRespTimeRevEDCH of RNRLC defines the reference AM RLC RTT value
when the reverse channel is the E-DCH.
AMRLCOnDCHOfStream/AMRLCOnDCHOfStreamFilterReTX (AM RLC retransmission filter for PS streaming with DCH)
Field
Related parameters
Issue 05E
Issue 06
AMRLCRespTimeDCH10 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 10 ms.
AMRLCRespTimeDCH10 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 10 ms.
AMRLCRespTimeDCH20 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 20 ms.
AMRLCRespTimeDCH20 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 20 ms.
AMRLCRespTimeDCH40 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 40 ms.
AMRLCRespTimeDCH40 of RNRLC defines the reference AM RLC RTT value
when the reverse transport channel is the
DCH with the TTI equal to 40 ms.
AMRLCRespTimeRevEDCH of RNRLC defines the reference AM RLC RTT value
when the reverse channel is the E-DCH.
AMRLCOnDCHOfNRTPS/AMRLCOnDCHOfNRTPSPeriodMax (AM RLC status period
max for PS NRT with DCH)
Field
Default value
Issue 05E
140
Issue 06
300
AMRLCOnEDCHOfNRTPS/AMRLCOnEDCHOfNRTPSPeriodMax (AM RLC status
period max for PS NRT with E-DCH)
DN70456011
Id:0900d80580a2e11c
Confidential
323
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Default value
Issue 05E
200
Issue 06
300
AMRLCOnHSDSCHOfNRTPS/AMRLCOnHSDSCHOfNRTPSPeriodMax (AM RLC
status period max for PS NRT with HS-DSCH)
Field
Default value
Issue 05E
200
Issue 06
300
RNTRM
ActivityFactorForAMRDCHTrafficBearers (Activity factor for AMR DCH traffic bearers)
Field
Description
Issue 05E
Issue 06
This parameter structure defines Activity
Factors for AMR calls for both DCH and
HSPA channel types. Activity Factors are
used to calculate correct AAL2 Link Characteristics.
This parameter structure defines Activity
Factors for AMR calls for both DCH and
HSPA channel types. Activity Factors are
used to calculate correct logical transport
resource reservation.
ActivityFactorForCSDCHTrafficBearers (Activity factor for CS DCH traffic bearers)
Field
Description
Issue 05E
Issue 06
This parameter structure defines the
Activity Factors for the CS DCH traffic
types. The Activity Factors are used to
calculate the correct AAL2 Link Characteristics.
This parameter structure defines the
Activity Factors for the CS DCH traffic
types. Activity Factors are used to calculate correct logical transport resource
reservation.
ActivityFactorForDCCHTrafficBearers (Activity factor for DCCH traffic bearers)
Field
Description
Issue 05E
Issue 06
This parameter structure defines activity
factors for DCCH traffic types. Activity
factors are used to calculate correct
AAL2 link characteristics.
This parameter structure defines activity
factors for DCCH traffic types. Activity
Factors are used to calculate correct
logical transport resource reservation.
ActivityFactorForFACHRACHTrafficBearers (Activity factor for FACH and RACH traffic
bearers)
Field
Description
324
Issue 05E
Issue 06
This parameter structure defines activity
factors for FACH and RACH traffic types.
Activity factors are used to calculate
correct AAL2 link characteristics.
This parameter structure defines activity
factors for FACH and RACH traffic types.
Activity Factors are used to calculate
correct logical transport resource reservation.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
ActivityFactorForFACHRACHTrafficBearers/AfFACHCCDL (Activity factor for FACHC/C DL bearer)
Field
Description
Issue 05E
Issue 06
This parameter defines the activity factor
for the FACH-C/C DL bearer and for the
HS FACH (signalling) bearer. The activity
factor value 1 means that there is no
overbooking for this bearer and, for
example, the value 0.5 means that the
overbooking ratio for the bearer is 2.
When you change the parameter value,
the new value is taken into use for any
new established bearers.
This parameter defines the activity factor
for the FACH-C/C and for the FACH-C/S
DLs bearer and for the HS FACH (signalling) bearer. The activity factor value 1
means that there is no overbooking for
this bearer and, for example, the value
0.5 means that the overbooking ratio for
the bearer is 2. When you change the
parameter value, the new value is taken
into use for any new established bearers.
ActivityFactorForHSPA (Activity factor for HSPA bearers)
Field
Issue 05E
Issue 06
Child parameters
•
•
•
•
Child parameters
AfRTHSDPA AfRTHSUPA AfSRBOnHS- AfPTTDL AfPTTUL AfRTHSDPA AfRTHDPA AfSRBOnHSUPA
SUPA AfSRBOnHSDPA AfSRBOnHSUPA
Related features
Transport Bearer Tuning (optional) AND
Streaming QoS for HSPA (optional)
AfRTHSDPA
AfRTHSUPA
AfSRBOnHSDPA
AfSRBOnHSUPA
•
•
•
•
•
•
AfPTTDL
AfPTTUL
AfRTHSDPA
AfRTHSUPA
AfSRBOnHSDPA
AfSRBOnHSUPA
Transport Bearer Tuning (optional) AND
( Streaming QoS for HSPA (optional)
OR PS conversational QoS for HSPA
(optional) OR Optimised push to talk
experience (optional) )
ActivityFactorForNRTDCHTrafficBearers (Activity factor for NRT DCH traffic bearers)
Field
Description
Issue 05E
Issue 06
This parameter structure defines activity
factors for NRT DCH traffic types. Activity
factors are used to calculate correct
AAL2 link characteristics.
This parameter structure defines activity
factors for NRT DCH traffic types. Activity
Factors are used to calculate correct
logical transport resource reservation.
ActivityFactorForPCHTrafficBearers (Activity factor for PCH traffic bearers)
DN70456011
Id:0900d80580a2e11c
Confidential
325
Summary of changes
Field
Description
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
This parameter structure defines activity
factors for PCH traffic types. Activity
factors are used to calculate correct
AAL2 link characteristics.
This parameter structure defines activity
factors for PCH traffic types. Activity
Factors are used to calculate correct
logical transport resource reservation.
ActivityFactorForRTPSTrafficBearers (Activity factor for RT PS traffic bearers)
Field
Description
Issue 05E
Issue 06
This parameter structure defines activity
factors for RT PS traffic types. Activity
factors are used to calculate correct
AAL2 link characteristics.
This parameter structure defines activity
factors for RT PS traffic types. Activity
Factors are used to calculate correct
logical transport resource reservation.
EchoRequestSending (Echo Request Sending)
Field
Related parameters
Issue 05E
Issue 06
N3Requests of RNTRM - If Echo
Request is sent N3-REQUESTS times
over the path without getting Echo
Response, the path is considered to be in
failure state.
N3Requests of RNTRM - If Echo
Request is sent N3-REQUESTS times
over the path without getting Echo
Response, the path is considered to be in
failure state.
T3Response of RNTRM - If Echo
Response message has not arrived
within a time specified by T3RESPONSE, Echo Response is considered to be lost
T3Response of RNTRM - If Echo
Response message has not arrived
within a time specified by T3RESPONSE, Echo Response is considered to be lost.
N3Requests (N3-REQUESTS)
Field
Issue 05E
Issue 06
Description
This parameter specifies the maximum
number of attempts for sending the Echo
Request message. If Echo Request is
sent N3-REQUESTS times over the path
without getting Echo Response, the path
is considered to be in failure state. This
parameter is not valid for GTPU units.
This parameter specifies the maximum
number of attempts for sending the Echo
Request message. If the Echo Request is
sent N3-REQUESTS times over the path
without getting an Echo Response, the
path is considered to be in failure state.
This parameter is not valid for GTPU
units.
Related parameters
EchoRequestSending of RNTRM - When
the Echo Request sending parameter
value is enabled, the N3-REQUESTS
parameter is applicable.
EchoRequestSending of RNTRM - When
the Echo Request Sending parameter
value is enabled, the N3-REQUESTS
parameter is applicable.
T3Response (T3-RESPONSE)
326
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
This parameter specifies the maximum
waiting time for the Echo Request
message. The T3-RESPONSE timer is
started when the Echo Request message
is sent. If the Echo Response message
has not arrived within a time specified by
T3-RESPONSE, the Echo Response is
considered to be lost. This parameter is
not valid for GTPU units.
This parameter specifies the maximum
waiting time for the Echo Request
message. The T3-RESPONSE timer is
started when the Echo Request message
is sent. If the Echo Response message
has not arrived within the time specified
by the T3-RESPONSE, the Echo
Response is considered to be lost. This
parameter is not valid for GTPU units.
Related parameters
EchoRequestSending of RNTRM - When
the Echo Request sending parameter
value is enabled, the T3-RESPONSE
parameter is applicable.
EchoRequestSending of RNTRM - When
the Echo Request Sending parameter
value is enabled, the T3-RESPONSE
parameter is applicable.
VCEL
HSDPAFmcgIdentifier (HSDPA FMCG identifier)
Field
Issue 05E
Related features
Issue 06
HSDPA (optional) AND HSPA InterRNC Cell Change (optional) AND
WCDMA - GSM Inter-system Handover
(optional)
LAC (Location area code)
Field
Issue 05E
Issue 06
Description
This parameter contains the Location
area code (LAC) of an IBTS cell. The
coding of the Location area code (two
octets) is the responsibility of administration.
LAI (Location Area Identification)
consists of PLMNid and LAC. If LAI has
to be deleted, LAC is set as 0xFFFE.
This parameter is also part of System
Information Block 1 and is known as IE:
GSM-MAP NAS system information.
This parameter contains the Location
area code (LAC) of an FD-BTS cell. The
coding of the Location area code (two
octets) is the responsibility of administration.
LAI (Location Area Identification)
consists of PLMNid and LAC. If LAI has
to be deleted, LAC is set as 0xFFFE.
Interfaces
RNC<->UE, RNC<->MSC, RAC<->RNC, RNC<->UE, RNC<->MSC, RAC<->RNC,
EM<->RNC, Planner<->RAC, RACApp<- EM<->RNC, Planner<->RAC, RACApp<>RAC
>RAC, RNC->OMS topology, RNC>OMS topology UI
RAC (Routing Area Code)
DN70456011
Id:0900d80580a2e11c
Confidential
327
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
This parameter defines the routing area
within the location area to which the IBTS
cell belongs. It is used only for PS
services (part of the PS domain-specific
NAS system information in SIB1).
The routing area identification (RAI)
consists of the location area identification
(LAI) and the RAC. The LAI consists of
the PLMNid and the location area code
(LAC).
This parameter defines the routing area
within the location area to which the FDBTS cell belongs.
The routing area identification (RAI)
consists of the location area identification
(LAI) and the RAC. The LAI consists of
the PLMNid and the location area code
(LAC).
Interfaces
RNC<->UE, RNC<->MSC, Planner<>RAC, RAC<->RNC, EM<->RNC,
RACApp<->RAC
RNC<->UE, RNC<->MSC, Planner<>RAC, RAC<->RNC, EM<->RNC,
RACApp<->RAC, RNC->OMS topology,
RNC->OMS topology UI
WANE
WANEName (WANE Name)
Field
Description
Issue 05E
Issue 06
This parameter can be used for identification of the authorised networks. The
maximum length of the name is 15 ASCII
chars. Allowed chars (A-Z, a-z, 0-9).
This parameter can be used for identification of the authorised networks. The
maximum length of the name is 15 ASCII
chars.
WBTS
RRMULDCHActivityFactor (Average UL DCH data rates for the radio bearers)
Field
Child parameters
Issue 05E
•
•
•
•
•
•
•
•
•
328
RRMULDCHActivityFactorCSAMR
RRMULDCHActivityFactorCSNTData
RRMULDCHActivityFactorCSTData
RRMULDCHActivityFactorPSBackgr
RRMULDCHActivityFactorPSStream
RRMULDCHActivityFactorPSTHP1
RRMULDCHActivityFactorPSTHP2
RRMULDCHActivityFactorPSTHP3
RRMULDCHActivityFactorSRB
Id:0900d80580a2e11c
Confidential
Issue 06
•
•
•
•
•
•
•
•
•
•
RRMULActivityFactorPTT
RRMULDCHActivityFactorCSAMR
RRMULDCHActivityFactorCSNTData
RRMULDCHActivityFactorCSTData
RRMULDCHActivityFactorPSBackgr
RRMULDCHActivityFactorPSStream
RRMULDCHActivityFactorPSTHP1
RRMULDCHActivityFactorPSTHP2
RRMULDCHActivityFactorPSTHP3
RRMULDCHActivityFactorSRB
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Child parameters
RRMULDCHActivityFactorCSAMR
RRMULDCHActivityFactorCSNTData
RRMULDCHActivityFactorCSTData
RRMULDCHActivityFactorPSBackgr
RRMULDCHActivityFactorPSStream
RRMULDCHActivityFactorPSTHP1
RRMULDCHActivityFactorPSTHP2
RRMULDCHActivityFactorPSTHP3
RRMULDCHActivityFactorSRB
RRMULActivityFactorPTT RRMULDCHActivityFactorCSAMR RRMULDCHActivityFactorCSNTData
RRMULDCHActivityFactorCSTData
RRMULDCHActivityFactorPSBackgr
RRMULDCHActivityFactorPSStream
RRMULDCHActivityFactorPSTHP1
RRMULDCHActivityFactorPSTHP2
RRMULDCHActivityFactorPSTHP3
RRMULDCHActivityFactorSRB
Description
The parameter defines the average UL
DCH data rate in relation to its maximum
allocated transport channel data rate.
The average UL DCH data rate is used
when the changes in the UL load and the
received interference power are estimated in the DCH resource allocation.
The average DCH rate is expected to
vary on the service basis, therefore
separate activity factors are defined for
the control plane signaling, CS AMR
calls, CS transparent data services, CS
non-transparent data services, PS
streaming services, PS interactive
services separated with the Traffic
Handling Priority values, and PS background services.
The parameter defines the average UL
DCH data rate in relation to its maximum
allocated transport channel data rate.
The average UL DCH data rate is used
when the changes in the UL load and the
received interference power are estimated in the DCH resource allocation.
The average DCH rate is expected to
vary on the service basis, therefore
separate activity factors are defined for
the control plane signaling, CS AMR
calls, CS transparent data services, CS
non-transparent data services, PS
streaming services, PS interactive
services separated with the Traffic
Handling Priority values, PS background
services and push to talk (PTT) services.
BTSIPAddress (BTS O&M IP address)
Field
Related features
Issue 05E
Issue 06
Nokia Integrated O&M for Andrew 3G
New WBTS Parameters in Topology
Pico BTS (optional), New WBTS Param- Data for Flexi/Ultra/MetroSite BTSs
eters in Topology Data for
(standard)
Flexi/Ultra/MetroSite BTSs (standard)
BTSSupportForHSPACM (BTS Support For HSPA CM)
DN70456011
Id:0900d80580a2e11c
Confidential
329
Summary of changes
Field
Description
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
This parameter defines whether the BTS
supports HSDPA or HSPA compressed
mode. If it is supported, the RNC can
start the HSDPA or HSPA compressed
mode in this BTS if it is needed. If HSPA
CM not supported, the RNC can start the
DCH compressed mode only. The
HSDPA or HSPA compressed mode can
be utilised only when the RNC configuration parameter CMmasterSwitch is
enabled
This parameter defines whether the BTS
supports HSDPA compressed mode. If it
is supported, the RNC can start the
HSDPA compressed mode in this BTS if
it is needed. If it is not supported, the
RNC can start the DCH compressed
mode only. The HSDPA compressed
mode can be utilised only when the RNC
configuration parameter CMmasterSwitch is enabled
PWSMShutdownEndHour (Hour when the cell shutdown window ends)
Field
Related parameters
Issue 05E
Issue 06
NBAPCommMode of WBTS - This
NBAPCommMode of WBTS - This
parameter is not valid if NBAP Communi- parameter is not valid if NBAP Communication Mode has value (NB/RSxxx).
cation Mode has value (NB/RSxxx).
PWSMShutdownEndMin of WBTS - This
parameter defines the ending time for cell
shutdown window.
PWSMShutdownBeginHour of WBTS This parameter defines the start time for
cell shutdown window.
PWSMShutdownBeginMin of WBTS This parameter defines the start time for
cell shutdown window.
PWSMShutdownEndMin of WBTS - This
parameter defines the ending time for cell
shutdown window.
PWSMEnableWakeUpTime of WBTS - If
the begin of the shutdown time limit and
the end of the shutdown time limit has the
same values for hour and minute, it is not
possible to enable cell activation based
on time of day.
PWSMShutdownBeginHour (Hour when the cell shutdown window starts)
330
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
NBAPCommMode of WBTS - This
NBAPCommMode of WBTS - This
parameter is not valid if NBAP Communi- parameter is not valid if NBAP Communication Mode has value (NB/RSxxx)
cation Mode has value (NB/RSxxx)
PWSMShutdownBeginMin of WBTS This parameter is used in defining the
start time for cell shutdown window.
PWSMShutdownBeginMin of WBTS This parameter is used in defining the
start time for cell shutdown window.
PWSMShutdownEndHour of WBTS This parameter defines the ending time
for cell shutdown window.
PWSMShutdownEndMin of WBTS - This
parameter defines the ending time for cell
shutdown window.
PWSMEnableWakeUpTime of WBTS - If
the begin of the shutdown time limit and
the end of the shutdown time limit has the
same values for hour and minute, it is not
possible to enable cell activation based
on time of day.
HSDPA14MbpsPerUser (HSDPA14MbpsPerUser)
Field
Interfaces
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
HSUPAXUsersEnabled (HSUPA x users enabled)
Field
Interfaces
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
MaxFPDLFrameSizeIub (Maximum FP downlink frame size Iub)
DN70456011
Id:0900d80580a2e11c
Confidential
331
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
The user plane frame size can be limited
with this parameter in order to avoid IP
layer fragmentation. The Adapter takes
the value into account during DL User
Plane traffic processing and limits the
maximum HS-DSCH FP frame size
accordingly. The value has to be planned
according to the minimum IP layer MTU
along the path to the BTS. The IP and
UDP header overheads have to be subtracted from the IP interface MTU value
(e.g. IPv4 IP header 20 bytes, UDP
header 8 bytes) when adjusting the value
since the parameter directly controls the
user plane FP frame size.
The user plane frame size can be limited
with this parameter in order to avoid IP
layer fragmentation. The RNC takes the
value into account at DL User Plane
traffic processing and limits the maximum
HS-DSCH FP frame size accordingly.
The value has to be planned according to
the minimum IP layer MTU along the path
to the BTS. The IP and UDP header overheads have to be subtracted from the IP
interface MTU value (e.g. IPv4 IP header
20 bytes, UDP header 8 bytes) when
adjusting the value since the parameter
directly controls the user plane FP frame
size.
Part of the BTS variants cannot
handle bigger than 1428 FP frames. RNC
keeps the maximum FP frame size
always limited to 1428 and additionally
obeys parameter values configured to
lower than 1428.
Range and step
540..9000, step 1
540..1472, step 1
Default value
1472
1428
DelayThresholdMax2msTTI (Maximum Threshold for HSUPA congestion delay 2msTTI
)
Field
Related parameters
Issue 05E
Issue 06
DelayThresholdMid2msTTI of WBTS The value of DelayThresholdMid2msTTI
always has to be less than the value of
DelayThresholdMax2msTTI.
DelayThresholdMid2msTTI of WBTS - If
DelayThresholdMax2msTTI is > 0, the
value of DelayThresholdMid2msTTI has
to be less than the value of
DelayThresholdMax2msTTI.
DelayThresholdMax (Maximum Threshold for HSUPA congestion handling delay)
Field
Related parameters
Issue 05E
Issue 06
DelayThresholdMid of WBTS - The value
of DelayThresholdMid always has to be
less than the value of DelayThresholdMax.
DelayThresholdMid of WBTS - If DelayThresholdMax is > 0, the value of DelayThresholdMid has to be less than the
value of DelayThresholdMax.
DelayThresholdMid2msTTI (Middle Threshold for HSUPA congestion delay 2msTTI )
332
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
DelayThresholdMax2msTTI of WBTS The value of DelayThresholdMid2msTTI
always has to be less than the value of
DelayThresholdMax2msTTI.
DelayThresholdMax2msTTI of WBTS - If
DelayThresholdMax2msTTI >0, the
value of DelayThresholdMid2msTTI has
to be less than the value of
DelayThresholdMax2msTTI.
DelayThresholdMin2msTTI of WBTS The value of DelayThresholdMid2msTTI
always has to be greater than the value of
DelayThresholdMin2msTTI.
DelayThresholdMin2msTTI of WBTS The value of DelayThresholdMid2msTTI
always has to be greater than the value of
DelayThresholdMin2msTTI.
DelayThresholdMid (Middle Threshold value for HSUPA congestion delay)
Field
Related parameters
Issue 05E
Issue 06
DelayThresholdMax of WBTS - The
value of DelayThresholdMid always has
to be less than the value of DelayThresholdMax.
DelayThresholdMax of WBTS - If DelayThresholdMax >0, the value of DelayThresholdMid has to be less than the value
of DelayThresholdMax.
DelayThresholdMin of WBTS - The value
of DelayThresholdMid always has to be
greater than the value of DelayThresholdMin.
DelayThresholdMin of WBTS - The value
of DelayThresholdMid always has to be
greater than the value of DelayThresholdMin.
PWSMShutdownEndMin (Minute when the cell shutdown window ends)
Field
Related parameters
Issue 05E
Issue 06
NBAPCommMode of WBTS - This
NBAPCommMode of WBTS - This
parameter is not valid if NBAP Communi- parameter is not valid if NBAP Communication Mode has value (NB/RSxxx).
cation Mode has value (NB/RSxxx).
PWSMShutdownEndHour of WBTS This parameter defines the ending time
for cell shutdown window.
PWSMShutdownBeginMin of WBTS This parameter defines the start time for
cell shutdown window.
PWSMShutdownEndHour of WBTS This parameter defines the ending time
for cell shutdown window.
PWSMRemCellSDBeginHour of WBTS This parameter defines the start time for
cell shutdown window.
PWSMEnableWakeUpTime of WBTS - If
the begin of the shutdown time limit and
the end of the shutdown time limit has the
same values for hour and minute, it is not
possible to enable cell activation based
on time of day.
PWSMShutdownBeginMin (Minute when the cell shutdown window starts)
DN70456011
Id:0900d80580a2e11c
Confidential
333
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Related parameters
Issue 05E
Issue 06
NBAPCommMode of WBTS - This
NBAPCommMode of WBTS - This
parameter is not valid if NBAP Communi- parameter is not valid if NBAP Communication Mode has value (NB/RSxxx)
cation Mode has value (NB/RSxxx)
PWSMShutdownBeginHour of WBTS This parameter defines the start time for
cell shutdown window.
PWSMShutdownBeginHour of WBTS This parameter defines the start time for
cell shutdown window.
PWSMShutdownEndHour of WBTS This parameter defines the ending time
for cell shutdown window.
PWSMShutdownEndMin of WBTS - This
parameter defines the ending time for cell
shutdown window.
PWSMEnableWakeUpTime of WBTS - If
the begin of the shutdown time limit and
the end of the shutdown time limit has the
same values for hour and minute, it is not
possible to enable cell activation based
on time of day.
NESWVersion (NE-SW-Version)
Field
Issue 05E
Issue 06
Description
This parameter specifies the WN release
(for example, WN3.0) of the WBTS in the
WCDMA.
This parameter specifies the main
release version of the WBTS as the WN
release or the WL release. WL is valid for
the Flexi Lite Base Station and WN for
other Base Station types.
This information is received from the
BTS when BTS O&M connection is
established.
Related features
Nokia Integrated O&M for Andrew 3G
New WBTS Parameters in Topology
Pico BTS (optional), New WBTS Param- Data for Flexi/Ultra/MetroSite BTSs
eters in Topology Data for
(standard)
Flexi/Ultra/MetroSite BTSs (standard)
NEType (NE-type)
Field
Range and step
Issue 05E
0 (not used), 1 (other), 2 (UltraBTS), 3
(FlexiBTS), 4 (PicoBTS), 9 (NB/RSxxx)
Issue 06
0 (not used), 1 (other), 2 (UltraBTS), 3
(FlexiBTS), 4 (PicoBTS), 9 (NB/RSxxx),
17 (FlexiLiteBTS)
LoadControlPeriodPS (PS load control period)
334
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Interfaces
Summary of changes
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
RRIndPeriod (Radio Resource Indication Period)
Field
Interfaces
Issue 05E
RNC<->WBTS, RAC<->RNC, EM<>RNC, RACApp<->RAC
Issue 06
RNC<->WBTS, RAC<->RNC, EM<>RNC, RACApp<->RAC, RNC->OMS
topology, RNC->OMS topology UI
RFSharingState (RF Sharing State)
Field
Interfaces
Issue 05E
WBTS->RNC, WBTS->EM, RNC->EM,
RNC->NetAct topology, RNC->OMS
topology, RNC->OMS topology UI
Issue 06
WBTS->RNC, WBTS->EM, RNC->EM,
RNC->NetAct topology, RNC->OMS
topology, RNC->OMS topology UI, RNC>RAC
SchedulingPeriod (Scheduling period)
Field
Issue 05E
Related parameters
Interfaces
Issue 06
LoadControlPeriodPS of WBTS - Value
should not be larger than the value of
LoadControlPeriodPS.
RAC<->RNC, EM<->RNC, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
WCEL
AllowedPreambleSignatures (Allowed preamble signatures)
DN70456011
Id:0900d80580a2e11c
Confidential
335
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
The preamble part in a PRACH channel
carries one of the 16 different orthogonal
complex signatures. The allowed
preamble signatures specify which signatures are used in a cell.
The allowed preamble signatures use
binary notation, where bit 0 indicates if
the signature #0 is allowed, bit 1 indicates
if the signature #1 is allowed, and so on.
If a bit is set to 1, the corresponding signature is allowed.
A maximum of four signatures is
allowed for WCEL.
The preamble part in a PRACH channel
carries one of the 16 different orthogonal
complex signatures. The allowed
preamble signatures specify which signatures are used in a cell.
The allowed preamble signatures use
binary notation, where bit 0 indicates if
the signature #0 is allowed, bit 1 indicates
if the signature #1 is allowed, and so on.
If a bit is set to 1, the corresponding signature is allowed.
A maximum of four signatures is
allowed for WCEL.
When HS-RACH (RAN1913) is
enabled in the cell by using HSRACHEnabled parameter, one signature is allocated for HS-RACH use. In that case the
signatures are allocated as follows:
- If all allowed four signatures are
configured by this parameter, the lowest
# of signature is allocated for HS-RACH
use and others for RACH use.
- If all allowed signatures are not configured by this parameter (<4), then the
first free lowest # of signature is allocated
for HS-RACH use and configured ones
for RACH use. (That is the total number
of allocated preamble signatures = one
preamble signature for HS-RACH + the
number of preamble signatures configured by this parameter).
Modification
onLine
objectLocking
Related parameters
NBAPCommMode of WBTS - If NBAP
Communication Mode has value
(NB/RSxxx), parameter modification
requires cell locking.
BlindHOEcNoThrTarget (Blind HO EcNo threshold for target cell)
Field
Units
Issue 05E
dBm
Issue 06
dB
KforCTCH (CBS frame offset (K))
336
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
This parameter defines the value of CBS
frame offset of CTCH on FACH.
This parameter defines the value of CBS
frame offset of CTCH on FACH. The
parameters N and K form CBS DRX
Level1 information which is broadcast as
system information in the System Information Block Type 5 or 6.
KforCTCH parameter is applicable
when WCEL-SABEnabled is set as
Enabled.
Related parameters
NbrOfSCCPCHs of WCEL - KforCTCH is
applicable if the number of the SCCPCHs
is 3.
NforCTCH of WCEL - Parameters N and
K form CBS DRX Level1 information,
which is broadcast as system information
in the System Information Block Type 5
or 6.
Related features
Service Area Broadcast (optional)
Service Area Broadcast (optional) OR
SAB Support with 2 SCCPCHs (optional)
CellRange (Cell range)
DN70456011
Id:0900d80580a2e11c
Confidential
337
Summary of changes
Field
Description
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
This parameter defines the maximum
range of the cell, that is, the maximum
distance from the cell site where a UE
can have a radio connection to the cell
including soft handover situations.
The maximum cell range can be 180
km when using two antennas (Rx Diversity Indicator = 1) and AICH Transmission Timing has value 1. The maximum
cell range can be 120 km when using four
antennas (Rx Diversity Indicator = 2) and
AICH Transmission Timing has value 1. If
AICH Transmission Timing has value = 0,
the maximum value of Cell range can be
10 km for both two and four antennas
configurations. If Cell Range is greater
than 10km, AICH Transmission Timing
should be 1 and Rx Diversity Indicator
should be 1 or 2.
The maximum cell range value
(180km, 60km or 35km) depends on the
RNC specific license.
This is a NSN-specific parameter. In
case of NSN BTS with 3GPP interface,
parameter modification requires object
locking.
This parameter defines the maximum
range of the cell, that is, the maximum
distance from the cell site where a UE
can have a radio connection to the cell
including soft handover situations.
The maximum cell range can be 180
km when using two antennas (Rx Diversity Indicator = 1) and AICH Transmission Timing has value 1. The maximum
cell range can be 120 km when using four
antennas (Rx Diversity Indicator = 2) and
AICH Transmission Timing has value 1. If
AICH Transmission Timing has value = 0,
the maximum value of Cell range can be
10 km for both two and four antenna configurations. If Cell Range is greater than
10km, AICH Transmission Timing should
be 1 and Rx Diversity Indicator should be
1 or 2.
The maximum cell range value
(180km, 60km, or 35km) depends on the
RNC specific license.
This is an NSN-specific parameter.
In case of NSN BTS with 3GPP interface,
parameter modification requires object
locking.
Special value
Related parameters
0
AICHTraTime of WCEL - If AICHTraTime
has value 0, the maximum Cell radius is
10km.
If AICHTraTime has value
1, the maximum Cell radius is 180km.
AICHTraTime of WCEL - If AICHTraTime
has value 0, the maximum Cell radius is
10km.
If AICHTraTime has value
1, the maximum Cell radius is 180km.
RxDivIndicator of WCEL - If RxDivInd has
value 1, the maximum Cell radius is
180km.
If RxDivInd has value 2,
the maximum Cell radius is 120km.
RxDivIndicator of WCEL - If RxDivInd has
value 1, the maximum Cell radius is
180km.
If RxDivInd has value 2,
the maximum Cell radius is 120km.
NBAPCommMode of WBTS - The
parameter "Cell range" is significant and
modifiable only in the UltraSite BTS /
FlexiBTS / PicoBTS cell.
NBAPCommMode of WBTS - The
parameter "Cell range" is significant and
modifiable only in the UltraSite BTS /
FlexiBTS / PicoBTS cell. The parameter
must be in the defined range if NBAPCommMode =0 and no special value permitted. If NBAPCommMode is not 0, the
cell range is invalid and RNC allows
special value 0.
CPCEnabled (CPC enabled)
338
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
Summary of changes
Issue 05E
Issue 06
This parameter enables / disables the
use of Continuous Packet Connectivity in
the cell.
If the parameter is enabled, the RNC
activates Continuous Packet Connectivity feature if possible for UEs which
support the feature. The following subfeatures are part of Continuous Packet
Connectivity feature:
- DPCCH Gating (UL DTX),
- CQI Reporting reduction,
- Discontinuous UL Reception (MAC
DTX) and
- Discontinuous DL Reception (DL
DRX).
Also UEs can be kept longer in
Cell_DCH state because of discontinuous transmission and reception.
This parameter enables / disables the
use of Continuous Packet Connectivity in
the cell.
If the parameter is enabled, the RNC
activates Continuous Packet Connectivity feature if possible for UEs which
support the feature. The following subfeatures are part of Continuous Packet
Connectivity feature:
- DPCCH Gating (UL DTX),
- CQI Reporting reduction,
- Discontinuous UL Reception (MAC
DTX) and
- Discontinuous DL Reception (DL
DRX).
Also UEs can be kept longer in
Cell_DCH state because of discontinuous transmission and reception.
Note: Simultaneous usage of CPC
and HSPA 128 users per cell (enabled
with parameter WCELHSPA128UsersPerCell) requires license
to be installed for ‘CPC for 128 HSPA
Users’ in RNC and the feature administrative state set as “ON”. Otherwise CPC
cannot be enabled.
CTCHCapaHighPri (CTCH capacity for High Priority CBS messages)
Field
Issue 05E
Issue 06
Description
Reserved CTCH capacity only for the
CBS messages with category High. A
certain amount of the total CTCH
capacity can be reserved for high priority
messages with this parameter.
Reserved CTCH capacity only for the
CBS messages with category High. A
certain amount of the total CTCH
capacity can be reserved for high priority
messages with this parameter.
CTCHCapaHighPri parameter is
applicable when WCEL-SABEnabled is
set as Enabled.
Related parameters
NbrOfSCCPCHs of WCEL - This parameter is applicable if the number of the
SCCPCHs (WCEL parameter "NbrOfSCCPCH") is 3.
Related features
Service Area Broadcast (optional)
Service Area Broadcast (optional) OR
SAB Support with 2 SCCPCHs (optional)
DCellHSDPAEnabled (DC HSDPA Enabled)
DN70456011
Id:0900d80580a2e11c
Confidential
339
Summary of changes
Field
Description
340
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
The parameter indicates whether or not
the DC HSDPA feature is enabled in the
cell. Before the feature is enabled in the
cell, the system checks that the
maximum amount of DC HSDPAcapable cells is not exceeded.
The parameter indicates whether or not
the DC HSDPA feature is enabled in the
cell. Before the feature is enabled in the
cell, the system checks that the
maximum amount of DC HSDPAcapable cells is not exceeded.
Two cells can form a DC HSDPA cell
pair when they have adjacent carrier frequencies within the same frequency
band, they belong to the same sector and
they have the same Tcell value.
In case of DB-DC-HSDPA, two cells
can form a cell pair when they have frequencies in different frequency bands.
NOTE: DC HSDPA cell pair must
belong to the same sector.
NOTE: DC HSDPA cell pair must
have the same Tcell value
NOTE: DC HSDPA cell pair must
belong to the same frequency band. Frequencies in different frequency bands are
allowed in case of DB-DC-HSDPA.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
SectorID of WCEL - DC HSDPA cell pair
must belong to the same sector.
HSUPAEnabled of WCEL - HSUPA
feature must be enabled in one (fixed
configuration) or both cells (flexible configuration).
Tcell of WCEL - DC HSDPA cell pair
must have the same Tcell value.
UARFCN of WCEL - DC HSDPA cell pair
must have adjacent frequencies.
HSUPAEnabled of WCEL - HSUPA
feature must be enabled in one (fixed
configuration) or both cells (flexible configuration).
HSPAQoSEnabled of WCEL - The
parameter must have the same value in
both cells of the DC HSDPA cell pair.
NBAPCommMode of WBTS - DC
HSDPA can be activated only if the value
of the parameter NBAPCommMode is 0
(UltraSite BTS, FelxiBTS, PicoBTS).
HSDPA14MbpsPerUser of WBTS HSDPA 14 Mbps per User feature must
be enabled in the BTS in order to activate
the dual cell HSDPA feature in the cell
pair.
DCellHSDPAFmcsId of WCEL - It is not
possible to enable the DC HSDPA
feature in the cell if DCellHSDPAFmcsId
has not been defined for the cell.
MIMOEnabled of WCEL - MIMO can be
enabled in a DC HSDPA cell if HSUPA is
enabled in the DC HSDPA cell. MIMO
must be disabled in a DC HSDPA cell if
HSUPA is disabled in the DC HSDPA
cell. In order to activate DC HSDPA in a
cell pair, MIMO must not be enabled in
any other than DC HSDPA cell within the
sector.
DCellAndMIMOUsage of WCEL - DCHSDPA must not be disabled if simultaneous usage of DC-HSDPA and MIMO is
enabled in the cell. The system checks
this condition.
FRLCEnabled of RNFC - Flexible RLC
must be enabled in the RNC in order to
activate the dual cell HSDPA feature.
HSDPAMobility of RNFC - Mobility with
serving HS-DSCH cell change must be
enabled in order to activate the dual cell
HSDPA feature.
DN70456011
Id:0900d80580a2e11c
Confidential
HSPAQoSEnabled of WCEL - The
parameter must have the same value in
both cells of the DC HSDPA cell pair.
NBAPCommMode of WBTS - DC
HSDPA can be activated only if the value
of the parameter NBAPCommMode is 0
(UltraSite BTS, FelxiBTS, PicoBTS).
HSDPA14MbpsPerUser of WBTS HSDPA 14 Mbps per User feature must
be enabled in the BTS in order to activate
the dual cell HSDPA feature in the cell
pair.
DCellHSDPAFmcsId of WCEL - It is not
possible to enable the DC HSDPA
feature in the cell if DCellHSDPAFmcsId
has not been defined for the cell.
MIMOEnabled of WCEL - MIMO can be
enabled in a DC HSDPA cell if HSUPA is
enabled in the DC HSDPA cell. MIMO
must be disabled in a DC HSDPA cell if
HSUPA is disabled in the DC HSDPA
cell. In order to activate DC HSDPA in a
cell pair, MIMO must not be enabled in
any other than DC HSDPA cell within the
sector.
DCellAndMIMOUsage of WCEL - DCHSDPA must not be disabled if simultaneous usage of DC-HSDPA and MIMO is
enabled in the cell. The system checks
this condition.
FRLCEnabled of RNFC - Flexible RLC
must be enabled in the RNC in order to
activate the dual cell HSDPA feature.
HSDPAMobility of RNFC - Mobility with
serving HS-DSCH cell change must be
enabled in order to activate the dual cell
HSDPA feature.
DBandHSDPAEnabled of WCEL - Dual
Cell HSDPA must be enabled in order to
enable Dual Band Dual Cell HSDPA. The
system checks this condition.
341
Summary of changes
Radio Network Parameters in Flexi Direct
OCULNRTDCHGrantedMinAllocT (DCH time limit for UL NRT DCH overload in E-DCH
cell)
Field
Related features
Issue 05E
Issue 06
HSUPA (optional) AND HSUPA Basic
RRM (optional)
HSFACHVolThrDL (DL traffic volume measurement threshold of HS-FACH)
Field
Description
Issue 05E
Issue 06
This parameter defines, in bytes, the
threshold of data in the RLC buffers of PS
RB that triggers the downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in
Cell_FACH state using HS-DSCH in DL.
Otherwise, RNC sends data on HSFACH.
Value “Infinity” means that data in
RLC buffers of PS RBs are not checked
and thus occupancy of RNC RLC buffer
can not trigger state transition from
CELL_FACH state to CELL_DCH state.
This parameter defines, in bytes, the
threshold of data in the RLC buffers of PS
RB that triggers the downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in
Cell_FACH state using HS-DSCH in DL.
Otherwise, RNC sends data on HSFACH.
Value “Infinity” means that data in
RLC buffers of PS RBs are not checked
and thus occupancy of RNC RLC buffer
cannot trigger state transition from
CELL_FACH state to CELL_DCH state.
TrafVolThresholdDLLow (Downlink traffic volume measurement low threshold)
Field
Related parameters
Issue 05E
Issue 06
TrafVolPendingTimeDL of RNPS - Indicates the period of time when forbidden
to send any new downlink capacity
requests, even if the triggering condition
is fulfilled again
TrafVolThresholdDLHigh of RNPS Defines the threshold of data in the RLC
buffer which triggers downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in a
Cell_DCH state and the initial bit rate
DCH is allocated for the radio bearer
TrafVolThresholdDLHigh of RNPS Defines the threshold of data in the RLC
buffer which triggers downlink traffic
volume measurement report (capacity
request) on MAC, when UE is in a
Cell_DCH state and the initial bit rate
DCH is allocated for the radio bearer
TrafVolTimeToTriggerDL of RNPS Defines the period of time between the
timing of event detection and the timing of
sending a downlink capacity request
TrafVolTimeToTriggerDL of RNPS Defines the period of time between the
timing of event detection and the timing of
sending a downlink capacity request
TrafVolPendingTimeDL of WAC - Indicates the period of time when forbidden
to send any new downlink capacity
requests, even if the triggering condition
is fulfilled again
EbNoSetIdentifier (Eb/No parameter set identifier)
342
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Interfaces
Summary of changes
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
PtxFDPCHMax (F-DPCH maximum transmission power)
Field
Issue 05E
Issue 06
Description
This parameter defines maximum power
for TPC bits of Fractional DPCH (FDPCH). Value of the parameter is subtracted from RNP parameter PtxPriCPICH which defines constant power
for primary CPICH to achieve final
signaled value.
If value of the parameter is equal to
value of the parameter PtxFDPCHMin,
BTS deactivates power control of HSPA
DL control channels.
This parameter defines maximum power
for TPC bits of Fractional DPCH (FDPCH). Value of the parameter indicates
a power level relative to primary CPICH
power. The signaled value is a negation
from the value set by this parameter.
If value of the parameter is equal to
value of the parameter PtxFDPCHMin,
BTS deactivates power control of HSPA
DL control channels.
Default value
9
4
Related features
HSDPA (optional) AND HSUPA
(optional) AND Fractional DPCH
(optional)
HSDPA (optional) AND HSUPA
(optional) AND ( Fractional DPCH
(optional) OR High speed Cell_FACH
Uplink (optional) )
PtxFDPCHMin (F-DPCH minimum transmission power)
Field
Issue 05E
Issue 06
Description
This parameter defines minimum power
for TPC bits of Fractional DPCH (FDPCH). Value of the parameter is subtracted from RNP parameter PtxPriCPICH that defines constant power for
primary CPICH to achieve final signaled
value.
If value of the parameter is equal to
value of the parameter PtxFDPCHMax,
BTS deactivates power control of HSPA
DL control channels.
This parameter defines minimum power
for TPC bits of Fractional DPCH (FDPCH). Value of the parameter indicates
a power level relative to primary CPICH
power. The signaled value is a negation
from the value set by this parameter.
If value of the parameter is equal to
value of the parameter PtxFDPCHMax,
BTS deactivates power control of HSPA
DL control channels.
Default value
20
10
Related features
HSDPA (optional) AND HSUPA
(optional) AND Fractional DPCH
(optional)
HSDPA (optional) AND HSUPA
(optional) AND ( Fractional DPCH
(optional) OR High speed Cell_FACH
Uplink (optional) )
Tcell (Frame timing offset of a cell)
DN70456011
Id:0900d80580a2e11c
Confidential
343
Summary of changes
344
Radio Network Parameters in Flexi Direct
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Description
DN70456011
Summary of changes
Issue 05E
Issue 06
Each cell in a BTS uses a System Frame
Number (SFN) counter, which is the BTS
Frame Number (BFN) counter delayed by
a number of chips defined by the value of
Tcell.
Tcell is used for defining the start of
SCH, CPICH, Primary CCPCH and DL
Scrambling Code(s) in a cell relative to
BFN. The main purpose is to avoid
having the overlapping SCHs in different
cells belonging to the same BTS. An SCH
burst is 256 chips long.
The values can be chosen as follows:
0 chips for the 1st cell of the BTS, 256
chips for the 2nd cell of the BTS, 512
chips for the 3rd cell of the BTS, and so
on.
Note: Changing the parameter value
starts the cell shutdown procedure in the
BTS.
In WN6.0 WBTS should control
HSDPA cell allocation in cases where
Minimum BaseBand Allocation or Shared
HSDPA Scheduler for BaseBand Efficiency are used so that only cells belonging to the same Tcell group are allocated
to the same MAC-hs/ehs entity. Cells
composing a Dual Cell HSDPA cell pair
must have the same Tcell value. One
MAC-hs/ehs entity can handle one Dual
Cell HSDPA cell pair.
In WN7.0 and onwards NSN BTS
should control HSDPA cell allocation so
that cells belonging to the Tcell groups 1
and 3 are allocated to the one MAC-hs
entity and Tcell groups 2 and 4 are allocated to the another MAC-hs entity. Tcell
group mapping to MAC-hs entities is
system module specific meaning that in
case there are MAC-hs entities in two
system modules above rule for Tcell
group mapping to MAC-hs entities is valid
in both system modules and so BTS
divides cells inside of those two groups
for MAC-eh entities according of BTS
commissioning. Note that this is valid
only for FlexiBTS Rel2 and UltraSite BTS
with EUBB.
In WN7.0 and onwards Tcell value
defines the group of cells, from which the
cell pair is formed by the RNC. The same
Tcell value must be set to all DC-HSDPA
Id:0900d80580a2e11c
capable cells, from which the cell pair is
Confidential
formed. The same Tcell value is allowed
in three DC-HSDPA cells in the same
Each cell in a BTS uses a System Frame
Number (SFN) counter, which is the BTS
Frame Number (BFN) counter delayed by
a number of chips defined by the value of
Tcell.
Tcell is used for defining the start of
SCH, CPICH, Primary CCPCH and DL
Scrambling Code(s) in a cell relative to
BFN. The main purpose is to avoid
having the overlapping SCHs in different
cells belonging to the same BTS. An SCH
burst is 256 chips long.
The values can be chosen as follows:
0 chips for the 1st cell of the BTS, 256
chips for the 2nd cell of the BTS, 512
chips for the 3rd cell of the BTS, and so
on.
Note: Changing the parameter value
starts the cell shutdown procedure in the
BTS.
In WN6.0 WBTS should control
HSDPA cell allocation in cases where
Minimum BaseBand Allocation or Shared
HSDPA Scheduler for BaseBand Efficiency are used so that only cells belonging to the same Tcell group are allocated
to the same MAC-hs/ehs entity. Cells
composing a Dual Cell HSDPA cell pair
must have the same Tcell value. One
MAC-hs/ehs entity can handle one Dual
Cell HSDPA cell pair.
In WN7.0 and onwards NSN BTS
should control HSDPA cell allocation so
that cells belonging to the Tcell groups 1
and 3 are allocated to the one MAC-hs
entity and Tcell groups 2 and 4 are allocated to the another MAC-hs entity. Tcell
group mapping to MAC-hs entities is
system module specific meaning that in
case there are MAC-hs entities in two
system modules above rule for Tcell
group mapping to MAC-hs entities is valid
in both system modules and so BTS
divides cells inside of those two groups
for MAC-eh entities according of BTS
commissioning. Note that this is valid
only for FlexiBTS Rel2 and UltraSite BTS
with EUBB.
In WN7.0 and onwards Tcell value
defines the group of cells, from which the
cell pair is formed by the RNC. The same
Tcell value must be set to all DC-HSDPA
345
capable cells, from which the cell pair is
formed. The same Tcell value is allowed
in three DC-HSDPA cells in the same
Summary of changes
Radio Network Parameters in Flexi Direct
WCELGlobalCNid (Global CN Id)
Field
Issue 05E
Issue 06
•
•
•
Child parameters
•
•
•
•
•
Child parameters
WCELCSCNId WCELMCC WCELMNC
WCELMNCLength WCELPSCNId
WCELMCC WCELMNC WCELMNCLength
Description
Global CN-ID (Global Core Network
index) is defined for each CN node. This
parameter is used to identify the operator
connected to this CN. PLMNid consists of
Mobile Country Code (MCC) and Mobile
Network Code (MNC). MCC together with
MNC identifies the PLMN uniquely (globally). MCC (Mobile Country Code) is
unique country identification.
Global CN-ID (Global Core Network
index) is defined for each CN node. This
parameter is used to identify the operator
connected to this CN. PLMNid consists of
Mobile Country Code (MCC) and Mobile
Network Code (MNC). MCC together with
MNC identifies the PLMN uniquely (globally). MCC (Mobile Country Code) is
unique country identification. With this
parameter WCEL can be associated with
Primary or Secondary (IUO-SharedAreaPLMNid) or with Common PLMNid.
WCELCSCNId
WCELMCC
WCELMNC
WCELMNCLength
WCELPSCNId
Related parameters
WCELMCC
WCELMNC
WCELMNCLength
CommonMCC of IADA - For MOCN,
WCELMCC can be associated with CommonMCC.
CommonMNC of IADA - For MOCN,
WCELMNC can be associated with CommonMNC.
PLMNid of IUO - WCEL can be associated with any of IUO-PLMNid.
SharedAreaPLMNid of IUO - For IMSI
Based HO, WCEL can also be associated with any of IUO-SharedAreaPLMNid
in case the WCEL is not defined as
MORAN or MOCN cell.
HSDPAenabled (HSDPA enabled)
346
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
PtxMaxHSDPA of WCEL - This parameter is applicable if the HSDPAenabled
value is "Enabled."
PtxMaxHSDPA of WCEL - This parameter is applicable if the HSDPAenabled
value is "Enabled."
PtxTargetHSDPA of WCEL - This param- PtxTargetHSDPA of WCEL - This parameter is applicable if the HSDPAenabled
eter is applicable if the HSDPAenabled
value is "Enabled."
value is "Enabled."
PtxOffsetHSDPA of WCEL - This param- PtxOffsetHSDPA of WCEL - This parameter is applicable if the HSDPAenabled
eter is applicable if the HSDPAenabled
value is "Enabled."
value is "Enabled."
HSDPAFmcsIdentifier of WCEL - This
HSDPAFmcsIdentifier of WCEL - This
parameter is applicable if the HSDPAen- parameter is applicable if the HSDPAenabled value is "Enabled."
abled value is "Enabled."
HSDPAFmciIdentifier of WCEL - This
HSDPAFmciIdentifier of WCEL - This
parameter is applicable if the HSDPAen- parameter is applicable if the HSDPAenabled value is "Enabled."
abled value is "Enabled."
HSDPAFmcgIdentifier of WCEL - This
HSDPAFmcgIdentifier of WCEL - This
parameter is applicable if the HSDPAen- parameter is applicable if the HSDPAenabled value is "Enabled."
abled value is "Enabled."
HSDPAHopsIdentifier of ADJS - This
HSDPAHopsIdentifier of ADJS - This
parameter is applicable if the HSDPAen- parameter is applicable if the HSDPAenabled value is "Enabled."
abled value is "Enabled."
AppAwareRANEnabled of WCEL - HSDPAenabled cannot be set to ‘Disabled’ if
Application Aware RAN feature is
enabled in the cell.
RTWithHSDPAFmcgIdentifier (HSDPA FMCG identifier for speech services)
Field
Issue 05E
Issue 06
Parameter Name
HSDPA FMCG identifier for AMR multiservice
HSDPA FMCG identifier for speech
services
Description
The parameter identifies the measurement control parameter set (FMCG
object) controlling inter-system measurements of a user having HS-DSCH allocated simultaneously with AMR speech
CS RAB.
The parameter identifies the measurement control parameter set (FMCG
object) controlling inter-system measurements of a user having HS-DSCH allocated simultaneously with AMR speech
CS RAB or user having push to talk allocated on HS-DSCH.
DN70456011
Id:0900d80580a2e11c
Confidential
347
Summary of changes
Field
Related parameters
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
FMCGId of FMCG - Parameter must
point to the existing FMCGId
FMCGId of FMCG - Parameter must
point to the existing FMCGId
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and HSDPAenabled
are set to enabled, and inter-system adjacency (ADJG) to GSM cell is defined for
the cell, special value 'Not defined' is not
allowed.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and HSDPAenabled
are set to enabled, and inter-system adjacency (ADJG) to GSM cell is defined for
the cell, special value 'Not defined' is not
allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and HSDPAenabled are set to enabled, and intersystem adjacency (ADJG) to GSM cell is
defined for the cell, special value 'Not
defined' is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and HSDPAenabled are set to enabled, and intersystem adjacency (ADJG) to GSM cell is
defined for the cell, special value 'Not
defined' is not allowed.
PTTEnabled of RNFC - If use of HSDPA
is enabled for PTT with the parameter
PTTEnabled (value > 1) and HSDPAenabled is set to enabled, and inter-system
adjacency (ADJG) to GSM cell is defined
for the cell, special value 'Not defined' is
not allowed.
Related features
HSDPA (optional) AND HSDPA with
Simultaneous AMR Voice Call (optional)
AND WCDMA - GSM Inter-system
Handover (optional)
HSDPA (optional) AND WCDMA - GSM
Inter-system Handover (optional) AND (
HSDPA with Simultaneous AMR Voice
Call (optional) OR Optimised push to
talk experience (optional) )
RTWithHSDPAFmciIdentifier (HSDPA FMCI identifier for speech services)
Field
348
Issue 05E
Issue 06
Parameter Name
HSDPA FMCI identifier for AMR multiservice
HSDPA FMCI identifier for speech
services
Description
The parameter identifies the measurement control parameter set (FMCI object)
controlling inter-frequency measurements of a user having HS-DSCH allocated simultaneously with AMR speech
CS RAB.
The parameter identifies the measurement control parameter set (FMCI object)
controlling inter-frequency measurements of a user having HS-DSCH allocated simultaneously with AMR speech
CS RAB or user having push to talk allocated on HS-DSCH.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
FMCIId of FMCI - Parameter must point
to the existing FMCIId.
FMCIId of FMCI - Parameter must point
to the existing FMCIId.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and HSDPAenabled
are set to enabled, and inter-frequency
neighbour (ADJI) is defined for the cell,
special value 'Not defined' is not allowed.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and HSDPAenabled
are set to enabled, and inter-frequency
neighbour (ADJI) is defined for the cell,
special value 'Not defined' is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and HSDPAenabled are set to enabled, and interfrequency neighbour (ADJI) is defined for
the cell,
special value 'Not defined'
is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and HSDPAenabled are set to enabled, and interfrequency neighbour (ADJI) is defined for
the cell,
special value 'Not defined'
is not allowed.
PTTEnabled of RNFC - If use of HSDPA
is enabled for PTT with the parameter
PTTEnabled (value > 1) and HSDPAenabled is set to enabled, and inter-frequency neighbour (ADJI) is defined for
the cell, special value 'Not defined' is not
allowed.
Related features
HSDPA (optional) AND HSDPA with
HSDPA (optional) AND ( HSDPA with
Simultaneous AMR Voice Call (optional) Simultaneous AMR Voice Call (optional)
OR Optimised push to talk experience
(optional) )
RTWithHSDPAFmcsIdentifier (HSDPA FMCS identifier for speech services)
Field
Issue 05E
Issue 06
Parameter Name
HSDPA FMCS identifier for AMR multiservice
HSDPA FMCS identifier for speech
services
Description
The parameter identifies the measurement control parameter set (FMCS
object) controlling intra-frequency measurements of a user having HS-DSCH
allocated simultaneously with AMR
speech CS RAB.
The parameter identifies the measurement control parameter set (FMCS
object) controlling intra-frequency measurements of a user having HS-DSCH
allocated simultaneously with AMR
speech CS RAB or user having push to
talk allocated on HS-DSCH.
DN70456011
Id:0900d80580a2e11c
Confidential
349
Summary of changes
Field
Related parameters
Radio Network Parameters in Flexi Direct
Issue 05E
Issue 06
FMCSId of FMCS - Parameter must point
to the existing FMCSId.
FMCSId of FMCS - Parameter must point
to the existing FMCSId.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and HSDPAenabled
are set to enabled, special value 'Not
defined' is not allowed.
HSDPAenabled of WCEL - If parameters
AMRWithHSDSCH and HSDPAenabled
are set to enabled, special value 'Not
defined' is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and HSDPAenabled are set to enabled, special value
'Not defined' is not allowed.
AMRWithHSDSCH of RNFC - If parameters AMRWithHSDSCH and HSDPAenabled are set to enabled, special value
'Not defined' is not allowed.
PTTEnabled of RNFC - If use of HSDPA
is enabled for PTT with the parameter
PTTEnabled (value > 1) and HSDPAenabled is set to enabled, special value 'Not
defined' is not allowed.
Related features
HSDPA (optional) AND HSDPA with
HSDPA (optional) AND ( HSDPA with
Simultaneous AMR Voice Call (optional) Simultaneous AMR Voice Call (optional)
OR Optimised push to talk experience
(optional) )
HSPAFmcsIdentifier (HSPA FMCS identifier)
Field
Interfaces
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
RTWithHSPAFmcsIdentifier (HSPA FMCS identifier for speech services)
Field
350
Issue 05E
Issue 06
Parameter Name
HSPA FMCS identifier for AMR multiservice
HSPA FMCS identifier for speech
services
Description
The parameter identifies the measurement control parameter set (FMCS
object) controlling the intra-frequency
measurements of a user having HSDSCH and E-DCH allocated simultaneously with AMR speech CS RAB.
After the modification of the parameter the new value is used for new connections.
The parameter identifies the measurement control parameter set (FMCS
object) controlling the intra-frequency
measurements of a user having HSDSCH and E-DCH allocated simultaneously with AMR speech CS RAB or user
having push to talk allocated on HSDSCH and E-DCH.
After the modification of the parameter the new value is used for new connections.
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
FMCSId of FMCS - Parameter must point
to the existing FMCSId.
FMCSId of FMCS - Parameter must point
to the existing FMCSId.
HSUPAEnabled of WCEL - If parameters
AMRWithEDCH and HSUPAenabled are
set to enabled, special value 'Not defined'
is not allowed.
HSUPAEnabled of WCEL - If parameters
AMRWithEDCH and HSUPAenabled are
set to enabled, special value 'Not defined'
is not allowed.
AMRWithEDCH of RNFC - If parameters
AMRWithEDCH and HSUPAenabled are
set to enabled, special value 'Not defined'
is not allowed.
AMRWithEDCH of RNFC - If parameters
AMRWithEDCH and HSUPAenabled are
set to enabled, special value 'Not defined'
is not allowed.
PTTEnabled of RNFC - If use of HSUPA
is enabled for PTT with the parameter
PTTEnabled (value > 2) and HSUPA is
enabled with the parameter HSUPAenabled, the special value 'Not defined' is
not allowed.
Interfaces
RAC<->RNC, EM<->RNC, RACApp<>RAC
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
Related features
HSUPA (optional) AND HSUPA with
HSUPA (optional) AND ( HSUPA with
Simultaneous AMR Voice Call (optional) Simultaneous AMR Voice Call (optional)
OR Optimised push to talk experience
(optional) )
HSPAQoSEnabled (HSPA QoS enabled)
DN70456011
Id:0900d80580a2e11c
Confidential
351
Summary of changes
352
Radio Network Parameters in Flexi Direct
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
HSDPAenabled of WCEL - The system
HSDPAenabled of WCEL - The system
checks if HSDPA is enabled in the cell
checks if HSDPA is enabled in the cell
before HSPA QoS features are activated. before HSPA QoS features are activated.
HSUPAEnabled of WCEL - The system HSUPAEnabled of WCEL - The system
checks if HSUPA is enabled in the cell
checks if HSUPA is enabled in the cell
before CS voice over HSPA is activated. before CS voice over HSPA is activated.
NBAPCommMode of WBTS - If this
parameter has value 1 (NB/RSxxx), then
the system prevents activation of HSPA
streaming and CS voice over HSPA
functionality to the cell belonging to that
NodeB.
NBAPCommMode of WBTS - If this
parameter has value 1 (NB/RSxxx), then
the system prevents activation of HSPA
streaming and CS voice over HSPA
functionality to the cell belonging to that
NodeB.
FDPCHEnabled of WCEL - The system
checks if Fractional DPCH is enabled in
the cell before CS voice over HSPA is
activated.
FDPCHEnabled of WCEL - The system
checks if Fractional DPCH is enabled in
the cell before CS voice over HSPA is
activated.
CPCEnabled of WCEL - The system
CPCEnabled of WCEL - The system
checks if CPC is enabled in the cell
checks if CPC is enabled in the cell
before CS voice over HSPA is activated. before CS voice over HSPA is activated.
AMRWithEDCH of RNFC - The system
checks if support of AMR multi HSPA
RAB is enabled before CS voice over
HSPA is activated.
DCellHSDPAEnabled of WCEL HSPAQoSEnabled must have the same
value in both cells of the DC HSDPA cell
pair.
AMRWithHSDSCH of RNFC - The
system checks if support of AMR multi
HSDPA RAB is enabled before CS voice
over HSPA is activated.
AMRWithEDCH of RNFC - The system
checks if support of AMR multi HSPA
RAB is enabled before CS voice over
HSPA is activated.
FRLCEnabled of RNFC - The system
checks that support of Flexible RLC is
enabled before CS voice over HSPA is
activated.
AMRWithHSDSCH of RNFC - The
system checks if support of AMR multi
HSDPA RAB is enabled before CS voice
over HSPA is activated.
HSDPADynamicResourceAllocation of
RNFC - The system checks if HSDPA
Dynamic Resource Allocation is activated before HSPA QoS features are
activated.
FRLCEnabled of RNFC - The system
checks that support of Flexible RLC is
enabled before CS voice over HSPA is
activated.
EDCHQOSClasses of RNHSPA - The
use of E-DCH can be prevented for given
traffic classes by this parameter
HSDSCHQoSclasses of RNHSPA - The
use of HS-DSCH can be prevented for
given traffic classes by this parameter.
HSDPADynamicResourceAllocation of
RNFC - The system checks if HSDPA
Dynamic Resource Allocation is activated before HSPA QoS features are
activated.
EDCHQOSClasses of RNHSPA - The
use of E-DCH can be prevented for given
traffic classes by this parameter
HSPANBRValues of RNHSPA - If HSPA
streaming is activated to the cell, then
HSDSCHQoSclasses of RNHSPA - The
Nominal Bit Rates defined by HSPANBR- use of HS-DSCH can be prevented for
Values are used in that cell.
given traffic classes by this parameter.
DN70456011
QoSPriorityMapping of RNPS - If a QoS
feature is activated to the cell, then priorities are defined byId:0900d80580a2e11c
QoSPriorityMapping
parameter also for High Confidential
Speed transport
channels.
HSPANBRValues of RNHSPA - If HSPA
streaming is activated to the cell, then
353
Nominal Bit Rates defined by HSPANBRValues are used in that cell.
QoSPriorityMapping of RNPS - If a QoS
Summary of changes
Radio Network Parameters in Flexi Direct
IncomingLTEISHO (Incoming ISHO from LTE)
Field
Description
Issue 05E
The parameter indicates if incoming
ISHO from LTE is enabled in the cell or
not.
Issue 06
The parameter indicates if incoming
ISHO from LTE is enabled in the cell ...or
not.
This parameter affects also feature
SRVCC from LTE and CSFB with HO.
SRVCC functionality is activated in the
cell only if both parameters SRVCCEnabled (for RNC) and IncomingLTEISHO
(for cell) are in state Enabled. CSFB functionality is activated in the cell only if both
parameters CSFBEnabled (for RNC) and
IncomingLTEISHO (for cell) are in state
Enabled.
LAC (Location area code)
Field
Related parameters
Issue 05E
PLMNid of IUPS - LAI (Location Area
Identification) consists of PLMNid and
LAC.
PLMNid of IUCS - LAI (Location Area
Identification) consists of PLMNid and
LAC.
Issue 06
RAC of WCEL - Routing area identification consists of LAI and RAC. The max
number of different LAI + different RAI +
different URAId is limited to 32.
URAId of WCEL - Location area identification (LAI) consists of PLMNId and LAC.
The max number of different LAI + different RAI + different URAId is limited to 32.
PLMNid of IUO - Location area identification (LAI) consists of PLMNId and LAC.
The max number of different LAI + different RAI + different URAId is limited to 32.
UsersPerHSSCCHCode (Max nbr of conv users per reserved HS-SCCH code)
354
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Summary of changes
Issue 05E
Issue 06
Description
This parameter defines the maximum
number of simultaneous HSPA conversational users that are admitted per one
reserved HS-SCCH code.
This parameter defines the maximum
number of simultaneous HSPA conversational users that are admitted per one
reserved HS-SCCH code.
Users counted here are CS voice
over HSPA users and push to talk (PTT)
users. One CS voice over HSPA user has
the same impact than 3 push to talk
users.
The maximum number of HS-SCCH
codes is defined with the parameter
WCEL-MaxNbrOfHSSCCHCodes.
CS voice over HSPA is enabled with
the WCEL-HSPAQoSEnabled parameter.
Optimized push to talk experience is
enabled with the RNFC-PTTEnabled
parameter.
Default value
30
32
Related parameters
MaxNbrOfHSSCCHCodes of WCEL The amount of HS-SCCH codes is
defined with the parameter MaxNbrOfHSSCCHCodes.
HSPAQoSEnabled of WCEL - The
parameter is used just if CS voice over
HSPA is activated in the cell.
Related features
HSDPA (optional) AND HSDPA
Dynamic Resource Allocation (optional)
AND QoS Aware HSPA Scheduling
(optional) AND HSDPA with Simultaneous AMR Voice Call (optional) AND
Fractional DPCH (optional) AND
HSUPA (optional) AND Continuous
Packet Connectivity (optional) AND CS
Voice Over HSPA (optional)
CS Voice Over HSPA (optional) OR
Optimised push to talk experience
(optional)
PrxMaxOrigTargetBTS (Max target received wide band original power for BTS)
Field
Issue 05E
Related parameters
Issue 06
PrxMaxTargetBTS of WCEL - The value
of the PrxMaxOrigTargetBTS must be
greater than or equal to the value of
parameter PrxMaxTargetBTS.
PrxMaxTargetBTS (Maximum target received wide band power for BTS)
DN70456011
Id:0900d80580a2e11c
Confidential
355
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Related parameters
Issue 05E
Issue 06
PrxNoise of WCEL - The value of the Prx- PrxNoise of WCEL - The value of the PrxMaxTargetBTS is relative to the system MaxTargetBTS is relative to the system
noise, PrxNoise.
noise, PrxNoise.
PrxLoadMarginEDCH of WCEL - Value
of the PrxMaxTargetBTS must be higher
than or equal to the value of the PrxLoadMarginEDCH.
PrxLoadMarginEDCH of WCEL - Value
of the PrxMaxTargetBTS must be higher
than or equal to the value of the PrxLoadMarginEDCH.
PrxMaxOrigTargetBTS of WCEL - The
value of the PrxMaxTargetBTS must be
smaller than or equal to the value of
parameter PrxMaxOrigTargetBTS.
MBLBInactivityEnabled (MBLB in Inactivity Enabled)
Field
Issue 05E
Issue 06
Description
This parameter defines if Multi-Band
Load Balancing is enabled when inactivity is detected in Cell_DCH state. If this
parameter is enabled, Multi-Band Load
Balancing is done with handover based
on (CM) measurements on Cell_DCH
state.
Changes in the parameter are
applied in upcoming inactivity detected
events in Cell_DCH state.
When this parameter is enabled,
HSPA capability based HO, MIMO capability based HO and DC-HSDPA capability based HO are not done in case of
inactivity detected in Cell_DCH state.
This parameter defines if Multi-Band
Load Balancing is enabled when inactivity is detected in Cell_DCH state. If this
parameter is enabled, Multi-Band Load
Balancing is done with handover based
on (CM) measurements on Cell_DCH
state.
When this parameter is enabled,
HSPA capability based HO, MIMO capability based HO and DC-HSDPA capability based HO are not done in case of
inactivity detected in Cell_DCH state.
Modification
onLine
objectLocking
MBLBMobilityEnabled (MBLB in Mobility Enabled)
Field
356
Issue 05E
Issue 06
Description
This parameter defines if Multi-Band
Load Balancing is enabled due to mobility
in Cell_DCH state. If this parameter is
enabled, Multi-Band Load Balancing is
done with handover based on (CM) measurements on Cell_DCH state.
Changes in the parameter are
applied in upcoming inactivity detected
events in Cell_DCH state.
This parameter defines if Multi-Band
Load Balancing is enabled due to mobility
in Cell_DCH state. If this parameter is
enabled, Multi-Band Load Balancing is
done with handover based on (CM) measurements on Cell_DCH state.
Modification
onLine
objectLocking
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Summary of changes
MBLBRABSetupEnabled (MBLB in RAB Setup Enabled)
Field
Issue 05E
Issue 06
Description
This parameter defines whether MultiBand Load Balancing is enabled in the
RAB setup phase. If enabled, Multi-Band
Load Balancing is done with blind handover, which is based on the RACH measurement from the source or target cell.
Note! To enable blind handover based on
source cell measurement RACHIntraFreqMesQuant should be set to value
RSCP. Blind handover based on target
cell measurements is enabled when this
parameter is enabled.
Changes in the parameter are
applied in upcoming RAB setups.
When this parameter is enabled,
Directed RRC connection setup for
HSDPA layer functionality is not applied
anymore (WCEL-DirectedRRCForHSDPALayerEnabled). In addition, the functionality of Directed RRC connection
setup is limited.
This parameter defines whether MultiBand Load Balancing is enabled in the
RAB setup phase. If enabled, Multi-Band
Load Balancing is done with blind handover, which is based on the RACH measurement from the source or target cell.
Note! To enable blind handover based on
source cell measurement RACHIntraFreqMesQuant should be set to value
RSCP. Blind handover based on target
cell measurements is enabled when this
parameter is enabled.
When this parameter is enabled,
Directed RRC connection setup for
HSDPA layer functionality is not applied
anymore (WCEL-DirectedRRCForHSDPALayerEnabled). In addition, the functionality of Directed RRC connection
setup is limited.
Modification
onLine
objectLocking
MBLBRABSetupMultiRAB (MBLB in RAB Setup for Multi RAB)
Field
Range and step
Issue 05E
Issue 06
0 (disabled), 1 (enabled when UE is in
Cell_FACH/Cell_PCH state), 2 (enabled
when UE is in Cell_DCH state), 3
(enabled when UE is in
Cell_DCH/Cell_FACH/Cell_PCH)
0 (Disabled), 1 (Enabled when UE is in
Cell_FACH/Cell_PCH state), 2 (Enabled
when UE is in Cell_DCH state), 3
(Enabled when UE is in
Cell_DCH/Cell_FACH/Cell_PCH)
MBLBStateTransEnabled (MBLB in State Transition Enabled)
DN70456011
Id:0900d80580a2e11c
Confidential
357
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Issue 05E
Issue 06
Description
This parameter defines if Multi-Band
Load Balancing is enabled in state transition to Cell_DCH state. If this parameter
is enabled, Multi-Band Load Balancing is
done with layering (new frequency given)
which is based on RACH measurement
from the source or target cell. Note! To
enable layering based on source cell
measurement, RACHIntraFreqMesQuant should be set to value
RSCP. Layering based on target cell
measurements is enabled when this
parameter is enabled.
Changes in the parameter are
applied in upcoming state transitions to
Cell_DCH state.
When this parameter is enabled,
WCEL-HSDPALayeringCommonChEnabled is not applied anymore.
This parameter defines if Multi-Band
Load Balancing is enabled in state transition to Cell_DCH state. If this parameter
is enabled, Multi-Band Load Balancing is
done with layering (new frequency given)
which is based on RACH measurement
from the source or target cell. Note! To
enable layering based on source cell
measurement, RACHIntraFreqMesQuant should be set to value
RSCP. Layering based on target cell
measurements is enabled when this
parameter is enabled.
When this parameter is enabled,
WCEL-HSDPALayeringCommonChEnabled is not applied anymore.
Modification
onLine
objectLocking
PtxTargetPSMin (Min DCH PS target for dynamic HSDPA pwr allocation)
Field
Related parameters
Issue 05E
Issue 06
HSDPAenabled of WCEL - Dynamic
target threshold PtxTargetPS is applicable only if HSDPA is enabled.
HSDPAenabled of WCEL - Dynamic
target threshold PtxTargetPS is applicable only if HSDPA is enabled.
PtxTargetPSMax of WCEL - PtxTargetPSMin must be lower than or equal to
the PtxTargetPSMax.
PtxTargetPSMax of WCEL - PtxTargetPSMin must be lower than or equal to
the PtxTargetPSMax.
HSDPADynamicResourceAllocation of
RNFC - Dynamic target threshold PtxTargetPS is applicable only if HSDPA
Dynamic Resource Allocation is enabled.
HSDPADynamicResourceAllocation of
RNFC - Dynamic target threshold PtxTargetPS is applicable only if HSDPA
Dynamic Resource Allocation is enabled.
PtxTargetPSMaxtHSRACH of WCEL The system checks whether the value
PtxTargetPSMin is lower than or equal to
the PtxTargetPSMaxHSRACH.
PrxTargetPSMin (Min PS target in HSPA-DCH interference sharing)
358
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
PrxNoise of WCEL - Value of the param- PrxNoise of WCEL - Value of the parameter is defined in the relation to the value eter is defined in the relation to the value
of the parameter PrxNoise.
of the parameter PrxNoise.
PrxTargetPSMax of WCEL - Parameter
must have a value lower than or equal to
the value of PrxTargetPSMax.
PrxTargetPSMax of WCEL - Parameter
must have a value lower than or equal to
the value of PrxTargetPSMax.
PrxTargetPSMaxtHSRACH of WCEL The system checks whether the value
PrxTargetPSMin is lower than or equal to
the PrxTargetPSMaxHSRACH.
MultiplePLMNListIncluded (Multiple PLMN List Included)
Field
Issue 05E
Issue 06
Description
This parameter defines if Multiple PLMN
List is broadcasted in the cell or not. If
MultiplePLMNListIncluded is set to 'Multiple PLMN List broadcasted', the Multiple
PLMN List is broadcasted in the cell. Otherwise, if MultiplePLMNListIncluded is
set to 'Multiple PLMN List not broadcasted', the Multiple PLMN List is not
broadcasted in the cell.
This parameter defines if Multiple PLMN
List is broadcasted in the cell or not. If
MultiplePLMNListIncluded is set to 'Multiple PLMN List broadcasted', the Multiple
PLMN List is broadcasted in the cell. Otherwise, if MultiplePLMNListIncluded is
set to 'Multiple PLMN List not broadcasted', the Multiple PLMN List is not
broadcasted in the cell. Multiple PLMN
list can contain all of the Primary
PLMNids that belong to different Operators.
Related parameters
MIBPLMNIdIncluded of RNFC - This
parameter defines if the PLMN identity
broadcasted in the MIB is included in the
multiple PLMN list.
MOCNenabled of RNFC - This parameter
is applicaple if MOCNenabled is set to
'Enabled'.
MOCNenabled of RNFC - This parameter
is applicaple if MOCNenabled is set to
'Enabled'.
NrtFmcgIdentifier (NRT FMCG Identifier)
Field
Interfaces
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
NrtFmciIdentifier (NRT FMCI Identifier)
DN70456011
Id:0900d80580a2e11c
Confidential
359
Summary of changes
Field
Interfaces
Radio Network Parameters in Flexi Direct
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
NrtFmcsIdentifier (NRT FMCS Identifier)
Field
Interfaces
Issue 05E
RAC<->RNC, EM<->RNC, RACApp<>RAC
Issue 06
RAC<->RNC, EM<->RNC, RACApp<>RAC, RNC->OMS topology, RNC>OMS topology UI
NbrOfSCCPCHs (Number of SCCPCHs)
Field
Description
Issue 05E
Issue 06
This parameter defines how many
SCCPCHs are configured for the cell.
If only one SCCPCH is used, it
carries FACH-c, FACH-u, and PCH. If
two SCCPCHs are used, the first
SCCPCH always carries only PCH, and
the second SCCPCH always carries
FACH-u and FACH-C. If three SCCPCHs
are used, the third SCCPCH carries
FACH-s and FACH-c-idle.
The recommended value of the transmission power of the SCCPCH depends
on the number of SCCPCHs.
The third SCCPCH is needed only if
SAB is available.
This parameter defines how many
SCCPCHs are configured for the cell.
If only one SCCPCH is used, it
carries FACH-c, FACH-u, and PCH. If
two SCCPCHs are used, the first
SCCPCH always carries only PCH, and
the second SCCPCH always carries
FACH-u and FACH-C. If three SCCPCHs
are used, the third SCCPCH carries
FACH-s and FACH-c-idle.
The recommended value of the transmission power of the SCCPCH depends
on the number of SCCPCHs.
The third SCCPCH is needed only if
SAB is available.
SAB can also be used with 2
SCCPCH configuration. If two SCCPCHs
are used with SAB, the first SCCPCH
always carries only PCH, and the second
SCCPCH always carries FACH-u and
FACH-c/FACH-s.
360
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Related parameters
Summary of changes
Issue 05E
Issue 06
PtxSCCPCH1 of WCEL - A recommended value of the transmission power
(Ptx) of the each SCCPCH depends on
the number of SCCPCHs.
PtxSCCPCH1 of WCEL - A recommended value of the transmission power
(Ptx) of the each SCCPCH depends on
the number of SCCPCHs.
PtxSCCPCH2 of WCEL - A recommended value of the transmission power
(Ptx) of the each SCCPCH depends on
the number of SCCPCHs.
PtxSCCPCH2 of WCEL - A recommended value of the transmission power
(Ptx) of the each SCCPCH depends on
the number of SCCPCHs.
PtxSCCPCH3 of WCEL - A recommended value of the transmission power
(Ptx) of the each SCCPCH depends on
the number of SCCPCHs.
PtxSCCPCH3 of WCEL - A recommended value of the transmission power
(Ptx) of the each SCCPCH depends on
the number of SCCPCHs.
PtxSCCPCH2SF128 of WCEL - A recommended value of the transmission power
(Ptx) of the each SCCPCH depends on
the number of SCCPCHs.
PtxSCCPCH2SF128 of WCEL - A recommended value of the transmission power
(Ptx) of the each SCCPCH depends on
the number of SCCPCHs.
SABEnabled of WCEL - SABEnabled can
be enabled if either NbrOfSCCPCHs
equals to 2 and NforCTCH is greater than
10 or NbrOfSCCPCHs is 3. To enable
SABEnabled directly with value 3 of
NbrOfSCCPCHs, both the values must
be applied in same operation.
Related features
Basic functions (standard) OR Service
Area Broadcast (optional)
Basic functions (standard) OR Service
Area Broadcast (optional) OR SAB
Support with 2 SCCPCHs (optional)
CPICHtoRefRABoffset (Offset of the P-CPICH and reference service powers)
Field
Issue 05E
Issue 06
Default value
2
0
Related parameters
PtxDLabsMax of WCEL - PtxDLabsMax
defines the planned maximum downlink
code power of the radio link when it
includes one or more PS NRT DCHs.
PtxDLabsMax of WCEL - PtxDLabsMax
defines the planned maximum downlink
code power of the radio link when it
includes one or more PS NRT DCHs.
PtxDPCHmax of WBTS - PtxDPCHmax
defines the maximum code channel
output power for the power control
dynamic range of BTS.
SectorID of WCEL - VALUE OF WCELWCEL-CPICHtoRefRABoffset have to be
identical in all wcels with same sector Id.
PtxDPCHmax of WBTS - PtxDPCHmax
defines the maximum code channel
output power for the power control
dynamic range of BTS.
NforCTCH (Period of CTCH allocation (N))
DN70456011
Id:0900d80580a2e11c
Confidential
361
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Description
Issue 05E
This parameter defines the period of
CTCH allocation on FACH carrying
CTCH. This parameter along with the
CBS frame offset (K) parameter determines the maximum capacity of the
CTCH.
CTCH capacity is calculated by the
following formula:
(((MaxSFNK)/N)*sizeof(SFN))/length of system
frame, where
MaxSFN = maximum system frame
number = 4096 and
sizeof(SFN) = Transport Block size
= 168 bits and
length of system frame = 4096*10 ms
= 40.96 second
=> CTCH capacity = (((4096K)/N)*168 bits)/40.96 s
Related parameters
KforCTCH of WCEL - The parameters N
and K form CBS DRX Level1 information
which is broadcast as system information
in the System Information Block Type 5
or 6.
Issue 06
This parameter defines the period of
CTCH allocation on FACH carrying
CTCH. This parameter along with the
CBS frame offset (K) parameter determines the maximum capacity of the
CTCH. NforCTCH parameter is applicable when WCEL-SABEnabled is set as
Enabled.
CTCH capacity is calculated by the
following formula:
(((MaxSFNK)/N)*sizeof(SFN))/length of system
frame, where
MaxSFN = maximum system frame
number = 4096 and
sizeof(SFN) = Transport Block size
= 168 bits and
length of system frame = 4096*10 ms
= 40.96 second
=> CTCH capacity = (((4096K)/N)*168 bits)/40.96 s
When NforCTCH > 10 and two SCCPCHs are configured to a cell, then
CTCH can be activated in this cell. CTCH
capacity is smaller with this feature but
capacity is twice from above formula as 2
Transport Blocks will be sent per TTI.
SABEnabled of WCEL - WCEL-SABEnabled is enabled and WCEL-NbrOfSCCPCHs equals to 2 then NforCTCH must
be greater than 10
NbrOfSCCPCHs of WCEL - NforCTCH is
applicable if the number of the SCCPCHs
is 3.
Related features
Service Area Broadcast (optional)
Service Area Broadcast (optional) OR
SAB Support with 2 SCCPCHs (optional)
PowerOffsetLastPreamblePRACHmessage (Power offset last preamble and PRACH
message)
Field
Default value
Issue 05E
2
Issue 06
-3
PowerRampStepPRACHpreamble (Power ramp step on PRACH preamble)
362
Id:0900d80580a2e11c
Confidential
DN70456011
Radio Network Parameters in Flexi Direct
Field
Default value
Summary of changes
Issue 05E
2
Issue 06
3
QHCS (Quality threshold level for HCS)
Field
Description
Issue 05E
Issue 06
This parameter defines the quality
threshold level (CPICH Ec/No) for
applying prioritised hierarchical cell reselection for a cell. It is needed only if
HCS is used.
The parameter is used for cell selection and re-selection in both idle and connected mode.
This parameter defines the quality
threshold level (CPICH Ec/No or CPICH
RSCP) for applying prioritised hierarchical cell re-selection for a cell. It is needed
only if HCS is used.
The parameter is used for cell selection and re-selection in both idle and connected mode.
Please notice that if CPICH RSCP is
set as quality measure with the WCELCellSelQualMeas parameter then the
parameter value range -24 … 0 (step 0.5)
means RSCP values -115 dBm … -67
dBm (values 0…48 for RSCP in SIBs).
RACHCapacity (RACH Capacity)
Field
Description
Issue 05E
Issue 06
The parameter defines the HW capacity
reserved for a RACH transport channel in
the BTS. RACH Capacity is indicated as
the number of decoded RACH messages
in a 10 ms radio frame. In case of WBTS
with 3GPP interface, parameter modification requires object locking. It is recommeded to use parameter value 4 if
functionality RRC connection setup on
common channels and/or HS
Cell_FACH feature are configured to be
used in this cell.
The parameter defines the HW capacity
reserved for a RACH transport channel in
the BTS. RACH Capacity is indicated as
the number of decoded RACH messages
in a 10 ms radio frame. In case of WBTS
with 3GPP interface, parameter modification requires object locking. It is recommended to use parameter value 4 if
functionality RRC connection setup on
common channels and/or HS
Cell_FACH feature are configured to be
used in this cell.
RACHIntraFreqMesQuant (RACH Intra Frequency Measurement Quantity)
DN70456011
Id:0900d80580a2e11c
Confidential
363
Summary of changes
Radio Network Parameters in Flexi Direct
Field
Description
Issue 05E
Issue 06
This parameter defines the intra-frequency measurement quantity for RACH
measurements. It is defined in SIB11,
SIB11bis, and SIB12 to the UE. The UE
reports the measurement results in the
requested quantity in RACH messages.
Bl