698 – 6000 MHz Base Station Antennas Filters Combiners and Amplifiers for Mobile Communications 2013

698–6000 Catalogue 2013 698 – 6000 MHz Base Station Antennas, Filters, Combiners and Amplifiers for Mobile Communications Photo on title page: Kathrein mobile communication products are well-prepared for up-to-date and future network requirements like e.g., mobile data services. Catalogue Issue 01/2013 All data published in previous catalogue issues hereby becomes invalid. We reserve the right to make alterations in accordance with the requirements of our customers, therefore for binding data please check valid data sheets on our homepage: www.kathrein.de Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4 and thereby respects the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The details given in our data sheets have to be f ollowed carefully when installing the antennas and accessories. In addition, please use our information brochure about mounting configurations. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. Calculation of Wind Loading on Kathrein Base Station Antennas In 1998 the co-ordinating committee of the Standardisation Group for Building Standards decided that during the harmonisation process of European standards, the DIN-Standards shall be modified and republished based on the European Pre-Standards. As a result of this harmonisation process the new edition of DIN 1055 Part 4 was finally published in 2005. This standard defines the worst case loading example created by natural wind forces on bearing structures and their individual elements. The standard thereby defines the principles for calculating the maximum loading and for confirming the bearing capacity of structures in general. One of the major changes in the calculation of the wind load under DIN 1055-4 is the definition of the value cf0. Due to these changes in the calculation formula within the standard, the calculated wind load of some Base Station Antennas is higher than previously specified on earlier data sheets. During 2009 Kathrein has migrated to calculating and specifying all wind loads in accordance with DIN 1055-4 (similar to the European Standard EN 1991-1-4) on the online data sheets. If the wind load has been calculated under the updated standard then this will be explicitly mentioned on the data sheet. The physical dimensions of our products have not been modified unless otherwise specified, nor has the actual wind loading surface area of the antennas increased in any way. “Quality leads the way” As the world’s oldest and largest antenna manufacturer, we live up to claim “Quality leads the way” on a daily basis. One of the fundamental principles is to always be on the lookout for the best solution for our customers. Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 9001 and EN ISO 14001. Internet: www.kathrein.de KATHREIN-Werke KG · Phone +49 80 31 184-0 · Fax +49 80 31 184-820 Anton-Kathrein-Straße 1 – 3 · P.O. Box 10 04 44 · D-83004 Rosenheim · Germany 790 … 960 MHz XPol 1710 … 2690 MHz XPol 790 … 960 MHz XXPol 1710 … 2690 MHz XXPol 698 – 894 MHz 1710 – 2170 MHz XPol (iRCU) XXPol (iRCU) 790 … 960 MHz 1710 … 2690 MHz XXPol 698 … 960 MHz 1710 … 2690 MHz XXXPol 698 … 960 MHz 1710 … 2690 MHz XXXXPol XXXXXPol 790 … 2690 MHz VPol Omni VPol, XPol Indoor VPol, VXPol, VHPol RET Electrical Accessories Mechanical Accessories Remote Electrical Tilt-System Splitters, Tappers and Measurement Tools Clamps, Downtilt Kits, ... List of available Catalogues for Mobile Communication Antennas and Accessories 698 – 6000 MHz Base Station Antennas, Filters, Combiners and Amplifiers for Mobile Communications 27 – 512 MHz KATHREIN-Antennas and Antenna Line Products Professional Antennas, Filters, Combiners and Multicouplers for Ground-to-Air Communications Antennas for Trains and Buses The listed catalogues are also available on CD-ROM All the listed catalogues and further product information can also be found on our homepage: www.kathrein.de In addition, you will find a list of Kathrein’s International Representatives for your local contact. For technical inquiries or orders please contact: mobilcom@kathrein.de 4 Catalogue 2013 —> Alterations to the Catalogue of 2012 Not longer in the catalogue 2013 Comments / Replacement 790 ... 960 MHz XPol 739619 739620 739489V01 741988V01 741989V01 742210V01 742218V01 742219V01 80010247V01 80010251V01 80010426V01 80010428V01 80010505V01 80010614V01 80010618V01 80010636 742233V01 80010511V01 80010290V01 80010454V01 80010492V01 80010665 80010675 80010692 739619V01 739620V01 1710 ...2690 MHz XPol Replaced by 80010679 Replaced by 80010711 Replaced by 80010678* (planned from 3Q13 onwards) 790 ... 960 MHz / 1710 ...2690 MHz XXPol 790 ... 960 MHz / 1710 ...2690 MHz XXXPol 80010290V02 Replaced by 80010753 790 ... 960 MHz / 1710 ...2690 MHz XXXXPol 80010685 80010686 730382 80010046 738449 80010147 86010147 790 ... 960 MHz VPol 80010665V01 80010675V01 80010692V01 80010685V01 80010686V01 80010046V01 Indoor VPol Replaced by 80010847 Replaced by 80010847 RET Stock clearing – Devices- and software status will remain unchanged Replaced by 86010148 Mechanical Accessories 732317 732318 732321 732322 737971 737972 737973 737974 737975 737977 85010005 85010006 Stock clearing – Replaced by 732327 Stock clearing – Replaced by 732327 Stock clearing – Replaced by 732327 Stock clearing – Replaced by 732327 Stock clearing – Replaced by 737978 Stock clearing – Replaced by 737978 Stock clearing – Replaced by 737978 Stock clearing – Replaced by 737978 Stock clearing – Replaced by 737978 Stock clearing – Replaced by 737978 Replaced by 86010076 Please note: New type numbers in the catalogue 2013 are shown and coloured in the respective register of the different antenna families. All phased out types will be available on request until end of 2013 unless otherwise announced. * Please contact us for a preliminary data sheet 5 Summary of Antenna Types, RET-Products and Accessories The articles are listed by type number in numerical order. New or changed product. Type No. Page 730... Type No. Page Page Type No. 738445 134 742264V02 85 800103.. Page 730376V02 129 738446 134 742265V02 88 80010300V01 27 730378V02 131 738450 140 742266V02 93 80010303V02 20 738546 192 742270V03 105 80010305V02 22 738908 202 742271V03 107 80010306V02 24 742272V03 109 80010307V01 24 742290 136 80010308V01 25 197 80010309V01 25 731... 731651 192 739... 732... 732327 193 734... 739619V01 18 742317 739620V01 18 742351V01 30 80010310V01 26 742352V01 68 80010360 47 80010368 132 80010375 46 80010378 40 741... 734360 201 741573 161 800100.. 734361 201 741790 152 80010046V01 734362 201 741984V01 41 734363 201 741990V01 43 734364 201 80010111 734365 201 80010121V01 98 80010430 162 80010122V01 99 80010431 165 742... 735... 735727 128 736... 137 800101.. 800104.. 150 80010425V01 742033 197 80010123V03 100 80010439V01 742034 197 80010126 154 80010442 742113 199 742192V01 135 80010456V02 80010465 800102.. 34 40 153 17 156 736347 146 742196V01 32 80010202V02 19 80010485V01 90 736349 147 742213V01 38 80010203V02 20 80010486V01 96 736350 143 742214V01 34 80010204V02 22 736854 130 742215V01 35 80010207V01 19 800105.. 742222V01 84 80010208V01 23 80010504V01 36 742223V02 86 80010215V01 23 80010510V01 65 26 80010516V01 53 80010517V01 55 737... 737398 203 742224V02 91 80010217V01 737978 194 742225V02 97 80010249 160 742226V01 83 80010274 149 742235V01 66 80010290V02 106 800106.. 738... 6 Type No. 738187 151 742236V01 63 80010291V02 108 80010605 44 738192 145 742237 61 80010292V03 110 80010606V01 45 738440 205 742263 197 80010294V02 21 80010621V01 37 Summary of Antenna Types, RET-Products and Accessories The articles are listed by type number in numerical order. New or changed product. Type No. Page 80010622 64 80010634V01 Type No. Page Type No. Page Type No. Page 80010722V01 77 85010015 196 86010100 182 21 80010723V01 78 85010016 196 86010101 182 80010642 16 80010734V01 70 85010017 196 86010102 182 80010643 16 80010735V01 71 85010058 197 86010103 182 80010644 62 80010736V01 72 85010059 197 86010104 182 80010647V01 54 80010744 61 85010060 198 86010105 182 80010651 39 80010747 148 85010061 198 86010130 180 80010652 67 80010748 158 85010075 200 86010131 180 80010664 87 80010749 159 85010076 200 86010136 183 80010665V01 92 80010753 82 85010080 174 86010137 183 80010666 95 80010761 31 86010138 183 80010667 50 80010764V01 73 860… 86010148 170 80010668 51 80010765V01 74 86010002 175 86010149 79 80010669 52 80010766V01 75 86010006 172 86010150 184 80010674 111 80010771 89 86010007 174 86010151 184 80010675V01 112 80010772 94 86010008 174 86010152 184 80010676 113 86010009 174 86010156 171 80010677 157 800108.. 86010010 174 80010679 42 80010804 122 86010011 174 K61... 80010681 33 80010805 123 86010012 174 K61335 80010682 60 80010816 56 86010013 174 80010684 124 80010817 57 86010014 174 K63... 80010685V01 125 80010825 120 86010015 174 K63236001 80010686V01 126 80010826 121 86010017 181 80010691 114 80010828V01 133 86010018 181 K75... 80010692V01 115 80010847 166 86010019 181 K751161 141 80010697 102 80010850 144 86010023 185 K7515641 142 80010698 103 80010892 118 + 119 86010026 172 80010699 104 86010029 174 86010030 176 850… 800107.. 85010002 192 86010031 177 80010709 163 85010003 192 86010032 174 80010710 164 85010008 195 86010033 174 80010711 31 85010010 48 86010046 173 80010721V01 76 85010014 196 86010054 174 204 185 7 Antenna Designs: Antenna Families Harmony of Design and Technology Omni XPol Panel Quad-band XPol Panel 800/900 XPol Panel 1800/2000/2600 8 VPol Panel 800/900 Directional Antenna Designs: Special Directional Antennas For Particular Applications Antennas for The distinguishing features of these special versions, e.g. parabolic panels or log. periodic antennas, are: – tunnel use – very small half-power beam width (high gain) – railway use – high sidelobe suppression – micro cells (street use) – also Dual-band and Multi-band versions – high gain link for repeaters – bidirectional horizontal pattern. BiDir Dual-Beam Panel LogPer 9 Antenna Designs: Antenna Families / RET-system Distinguishing features Design Compact size and elegant design are the distinguishing features of Kathrein’s antenna families. Radome The radomes cover the internal antenna components. The fiberglass material guarantees optimum performance with regards to stability, strength, UV resistance, painting and weather protection. Environmental influences Kathrein antenna designs are based on fundamental engineering knowledge and also on our decades of practical experience, during which the various constructions and materials used have proved their outstanding reliability. Environmental conditions Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regards to the following items: – Low temperature: –55 °C – High temperature (dry): +60 °C Impedance Standard Impedance for all products is 50 Ω unless otherwise stated. Great variety of According to the antenna type selected, customers can choose from different half-power beam width, half-power beam widths, gain values and electrical downtilts for panel gain values, antennas. Downtilts are either fixed or adjustable or even controlled by remote electrical downtilt electrical tilt system (RET). Low intermodulation After many years of experience in the construction of antennas and after products (typ. <–150 dBc) intensive research into the effects of intermodulation, we have been able to optimize the material and technology used for antennas (the given value refers to 3rd order products measured with 2 carriers of 20 W each). Excellent tracking Tracking states the symmetry between the +45° and –45° polarized horizontal pattern. Bad tracking values lead to interferences in the network and reduced diversity performance. Kathreins special Tracking compensation reduces the average value measured at ±60° to < 2 dB. Superior squint Squint, also often referred to as “Pattern Symmetry”, gives the symmetry of the pattern over the whole frequency range measured at the 3 dB points. Interferences and nulls in the network may be the result of bad values. In contrast to the vertical squint which is usually good, excellent squint values of the horizontal pattern are hard to reach. Kathreins superior values of ± 5 % of the half-power beam width are in line with the requirements from system suppliers. Multi-array design Besides standard single array antennas, Kathrein designs antennas providing multiple antenna arrays in one radome. These multi-array antennas do not only supply a future-proof multiplicity of diverse frequency bands for various technologies, but are also well-prepared for different MIMO-applications. The Kathrein portfolio contains a high variety of design solutions like interleaved and side-by-side antenna types or combinations of both as well as filter realizations. Excellent grounding The antennas are DC grounded according EN 50083-1. Multi-functional Depending on the type, the antennas are equipped with up to 2 attachment installation hardware points. Panels can be wall-mounted without any additional hardware. For mast-mounting, brackets and mechanical downtilt kits are available. To assist the installation technicians in aligning the panels, an azimuth adjustment tool can be supplied (see Mechanical Accessories). MTBF Statement Traditionally, passive components like antennas cannot be well calculated due to the lack of a sufficient number of components in the MTBF library. Unfortunately, this constraint results in a very inaccurate calculation. Thus, such results are technically questionable and unrealistic. In essence, antennas are made out of mechnical parts that do not show any failure rates. Only available failure rates can be calculated into an MTBF value. Consequently such components cannot be listed in any MTBF library. Remote Electical Tilt System Kathrein hereby states that RET devices, as far as the functionality and features are described within the AISG / 3GPP standard, are compliant with AISG Compliancy the standard. 10 Downtilting of Antennas: Downtilt Possibilities Mechanical downtilt For further technical information please see “Mechanical Accessories”, page 191. Electrical downtilt Description of the adjustment mechanism (protective cap removed): 1 1 2 2 ➀ Adjustment wheel with twist-lock function. ➁ Downtilt spindle with integrated scale. ➀ Thread for fixing the pro tective cap or the RCU (Remote Control Unit). ➁ Gearwheel for RCU power drive. To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gearwheel must be used for alignment. Manual adjustment procedure: General Instructions for Feederline Installation min.° – max.° for Dual-band Antennas Remove the protective cap. Set downtilt angle by rotating Screw on the protective cap the adjustment wheel. again. Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width. Remote Electrical Tilt (RET) For further technical information please see “RET”, pages 168 and 169. Description of bottom end cap (exemplary picture): Description of bottom end cap (exemplary picture): Adjustment mechanism (protective cap removed) Ventilation hole Spindle with tilting scale 7-16 female (long neck) Color coding: Correlation of each RF input to: – the corresponding adjustment mechanism – the frequency range – the polarization 11 Kathrein Antennas Product Description (Type) XXPol Panel 870–960/1710–1880 C 65°/60° 17/18dBi 2°–8°T/2°T Polarization(s): (X) Dual +45°/–45° (V) Vertical Antenna Family Frequency Range(s) Integrated Combiner Horizontal Half-power Beam Width(s) Gain Value(s) Variable / Fixed Electrical Tilt(s) 12 Characteristical Horizontal and Vertical Antenna Patterns Horizontal Patterns: 45° 30° 20° 3 0 dB dB 3 10 10 3 0 0 45° 30°/33° 20° dB 10 120° 90° 65° 10 215° 10 3 0 dB 10 dB 3 180° 3 0 0 120° 88°/90° 60°/65° dB 120° Vertical Patterns: 65° 15° 30° 10 0 65° 0 10° 10 3 10 dB dB 10° 4° 6° 10 0 15° 30° 0 6° 3 dB 0 3 3 dB 3 10 dB 3 dB 10 0 4° 13 14 Summary – Directional Antennas XPol 790...960 MHz Dual Polarization +45°/–45° Type Type No. Height [mm] 80010642 80010643 80010456V02 1298 2254 2254 XPol Panel XPol Panel XPol Panel 790–960 790–960 790–960 30° 30° 30° 18dBi 21dBi 20.5dBi 0°T 0°T 0°–10°T XPol Panel 790–960 65° 9dBi 0°T 739619V01 XPol Panel 806–960 65° 12.5dBi 0°T XPol Panel XPol Panel XPol Panel 790–960 790–960 790–960 65° 65° 65° 15dBi 15dBi 15dBi XPol Panel XPol Panel XPol Panel 790–960 790–960 790–960 65° 65° 65° XPol Panel XPol Panel 790–960 790–960 XPol Panel XPol Panel XPol Panel XPol Panel Connector position Page rearside rearside rearside 16 16 17 256 bottom or top 18 739620V01 656 bottom or top 18 0°T 6°T 0°–14°T 80010202V02 80010207V01 80010303V02 1294 1294 1294 bottom bottom bottom 19 19 20 17dBi 17dBi 16.5dBi 0°T 6°T 0°–10°T 80010203V02 80010294V02 80010634V01 1934 1934 1934 rearside rearside rearside 20 21 21 65° 65° 18dBi 17.5dBi 0°T 0°–8°T 80010204V02 80010305V02 2254 2254 rearside rearside 22 22 790–960 790–960 790–960 790–960 65° 65° 65° 65° 18dBi 18dBi 17.5dBi 18dBi 0°T 6°T 0°–10°T 0°–10°T 80010215V01 80010208V01 80010306V02 80010307V01 2574 2574 2574 2574 rearside rearside bottom rearside 23 23 24 24 XPol Panel 790–960 85° 13.5dBi 0°–14°T 80010308V01 1294 bottom 25 XPol Panel 790–960 85° 15dBi 0°–10°T 80010309V01 1934 rearside 25 XPol Panel XPol Panel XPol Panel 790–960 790–960 790–960 85° 85° 85° 17dBi 16dBi 16.5dBi 0°T 0°–10°T 0°–10°T 80010217V01 80010310V01 80010300V01 2574 2574 2574 rearside bottom rearside 26 26 27 New or changed product 15 Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 30° 18dBi 0°T Type No. Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 16 30° 80010642 s clamped d lu c in 790 – 960 824 – 894 MHz +45°, –45° 2 x 17.6 dBi 880 – 960 MHz +45°, –45° 2 x 18 dBi 33° > 30 dB 32° > 30 dB 30° > 30 dB 25 dB 25 dB 1.0 dB ±1.0° 25 dB 14.5° 14.0° 12.8° ≥ 14 dB ≥ 13 dB ≥ 12 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Frontal / lateral / rearside: 970 / 180 / 1160 N 1298 / 576 / 99 mm M (Medium) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Type No. VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply X 790 – 862 MHz +45°, –45° 2 x 17.5 dBi XPol Panel 790–960 30° 21dBi 0°T Frequency range Polarization Gain at 0° T Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above main beam 790 – 960 80010643 s clamped includ 790 – 862 MHz +45°, –45° 2 x 20.2 dBi 790 – 960 824 – 894 MHz +45°, –45° 2 x 20.4 dBi 880 – 960 MHz +45°, –45° 2 x 20.8 dBi 33° > 30 dB 32° > 30 dB 30° > 30 dB Typically: 30 dB Typically: 26 dB 2.0 dB ±2.0° Typically: 23 dB 8..4° 8.2° 7.4° > 15 dB > 15 dB > 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 1760 / 330 / 2040 N 2254 / 576 / 99 mm H (Heavy) 20.5 kg / 22.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 30° 20.5dBi 0°–10°T Type No. 790 – 960 X 30° s clamped d lu c in 80010456V02 790 – 862 MHz +45°, –45° 2 x 20.0 dBi 790 – 960 824 – 894 MHz +45°, –45° 2 x 20.2 dBi 880 – 960 MHz +45°, –45° 2 x 20.5 dBi 33° > 28 dB 32° > 29 dB 30° > 30 dB Typically: 25 dB Typically: 23 dB 2.5 dB ±2.0° Typically: 20 dB Frequency range Polarization Gain at 0° T Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 8.8° 8.5° 0.5°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T > 16 ... 13 ... 13 dB > 18 ... 18 ... 17 dB > 18 ... 16 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1760 / 330 / 2040 N 2254 / 576 / 99 mm H (Heavy) 22 kg / 24 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 9.1° For more information about additional mounting accessories please refer to page 191 17 Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 65° 9dBi Type No. Frequency range Polarization Gain Half-power beam width Copolar +45°/–45° Front-to-back ratio, copolar Cross polar ratio 0° Maindirection Sector ±60° Isolation VSWR Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Max. wind velocity Height/width/depth Category of mounting hardware Weight Frequency range Polarization Gain Half-power beam width Copolar +45°/–45° Front-to-back ratio, copolar Isolation VSWR Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Max. wind velocity Height/width/depth Category of mounting hardware Weight Scope of supply 18 X 65° 739619V01 790 – 960 790 – 880 MHz +45°, –45° 2 x 8.5 dBi Horizontal: 70° Vertical: 70° > 27 dB 880 – 960 MHz +45°, –45° 2 x 9 dBi Horizontal: 65° Vertical: 68° > 27 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB > 30 dB < 1.7 (790 –806 MHz) < 1.5 (806 –960 MHz) < –150 dBc ( 2 x 43 dBm carrier) 350 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 40 / 25 / 90 N 200 km/h 256 / 262 / 116 mm M (Medium) 3 kg XPol Panel 806–960 65° 12.5dBi Type No. 790/806 – 960 739620V01 806 – 960 806 – 880 MHz +45°, –45° 2 x 12 dBi Horizontal: 68° Vertical: 29° s clamped d lu c in 880 – 960 MHz +45°, –45° 2 x 12.5 dBi Horizontal: 65° Vertical: 27° > 30 dB > 30 dB < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 220 / 85 / 300 N 200 km/h 656 / 262 / 116 mm M (Medium) 6 kg / 8 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 65° 15dBi 0°T Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Maindirection Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 65° s clamped d lu c in 80010202V02 790 – 960 824 – 894 MHz +45°, –45° 2 x 14.7 dBi 880 – 960 MHz +45°, –45° 2 x 15 dBi 69° > 23 dB 68° > 24 dB 65° > 25 dB > 20 dB > 11 dB > 20 dB > 11 dB 0.5 dB ±2.0° > 20 dB > 11 dB 14.7° 14.3° 13.2° > 14 dB > 15 dB > 14 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom Frontal / lateral / rearside: 430 / 200 / 600 N 1294 / 259 / 99 mm M (Medium) 6.5 kg / 8.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Type No. VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply X 790 – 862 MHz +45°, –45° 2 x 14.5 dBi XPol Panel 790–960 65° 15dBi 6°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for: first sidelobe above horizon sector 0°–30° above horizon 790 – 960 s clamped includ 80010207V02 790 – 862 MHz +45°, –45° 2 x 14.5 dBi 790 – 960 824 – 894 MHz +45°, –45° 2 x 14.7 dBi 880 – 960 MHz +45°, –45° 2 x 15 dBi 66° > 30 dB 65° > 30 dB 63° > 30 dB Typically: > 20 dB Typically: > 10 dB Typically: > 20 dB Typically: > 10 dB Typically: > 20 dB Typically: > 10 dB 16° 15.7° 6°, fixed 14.6° > 13 dB > 13 dB > 14 dB > 14 dB > 16 dB > 14 dB < 1.4 < 1.3 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom Frontal / lateral / rearside: 790 / 370 / 1090 N 1294 / 259 / 99 mm M (Medium) 7.5 kg / 9.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 19 Panel Dual Polarization Half-power Beam Width 790 – 960 X 65° XPol Panel 790–960 65° 15dBi 0°–14°T Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio 0° Maindirection Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above horizon VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 80010303V02 s clamped d lu c in 790 – 862 MHz +45°, –45° 14.5 ... 14.4 ... 14.3 0° ... 7° ... 14° 790 – 960 824 – 894 MHz +45°, –45° 14.7 ... 14.5 ... 14.4 0° ... 7° ... 14° 880 – 960 MHz +45°, –45° 15 ... 14.8 ... 14.7 0° ... 7° ... 14° 67° > 24 dB 66° > 25 dB 65° > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 15.7° 15.5° 15° 0°– 14°, continuously adjustable 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T 15 ... 14 ... 15 dB 18 ... 15 ... 15 dB 18 ... 15 ... 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 440 / 210 /610 N 1294 / 259 / 99 mm M (Medium) 8.5 kg / 10.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter XPol Panel 790–960 65° 17dBi 0°T Type No. 80010203V02 s clamped includ Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±30° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon 790 – 862 MHz +45°, –45° 2 x 16.4 dBi 790 – 960 824 – 894 MHz +45°, –45° 2 x 16.6 dBi 880 – 960 MHz +45°, –45° 2 x 16.9 dBi 69° > 25 dB 67° > 25 dB 65° > 25 dB > 22 dB > 18 dB > 14 dB > 22 dB > 18 dB > 14 dB 0.5 dB ±2.0° > 22 dB > 18 dB > 14 dB 9.9° 9.5° 8.9° > 13 dB > 15 dB > 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 20 < 1.5 < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 690 / 310 / 910 N 1934 / 259 / 99 mm M (Medium) 9.5 kg / 11.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 65° 17dBi 6°T Type No. 790 – 960 X 65° s clamped d lu c in 80010294V02 Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above horizon 790 – 862 MHz +45°, –45° 2 x 16.2 dBi 790 – 960 824 – 894 MHz +45°, –45° 2 x 16.5 dBi 880 – 960 MHz +45°, –45° 2 x 16.9 dBi 69° > 25 dB 68° > 25 dB 65° > 25 dB Typ. > 20 dB Typ. > 10 dB Typ. > 20 dB Typ. > 10 dB 1.0 dB ±1.5° Typ. > 20 dB Typ. > 10 dB 9.4° 9.3° 6°, fixed 8.8° > 14 dB > 15 dB > 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 < 1.4 < 1.3 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 690 / 310 / 910 N 1934 / 259 / 99 mm M (Medium) 9.5 kg / 11.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter XPol Panel 790–960 65° 16.5dBi 0°–10°T Type No. Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped includ 80010634V01 790 – 862 MHz +45°, –45° 16.2 ... 16.4 ... 16.2 0° ... 5° ... 10° 790 – 960 824 – 894 MHz +45°, –45° 16.3 ... 16.6 ... 16.3 0° ... 5° ... 10° 880 – 960 MHz +45°, –45° 16.6 ... 16.8 ... 16.6 0° ... 5° ... 10° 69° > 24 dB 68° > 25 dB 65° > 25 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB 0.5 dB ±1.5° Typically: 20 dB > 10 dB 10° 9.9° 9.7° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 18 ... 18 ... 18 dB 18 ... 18 ... 18 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 680 / 310 / 900 N 1934 / 259 / 99 mm M (Medium) 11 kg / 13 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 21 Panel Dual Polarization Half-power Beam Width 790 – 960 X 65° XPol Panel 790–960 65° 18dBi 0°T 80010204V02 Type No. s clamped d lu c in Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Maindirection Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon 790 – 862 MHz +45°, –45° 2 x 17.2 dBi 790 – 960 824 – 894 MHz +45°, –45° 2 x 17.5 dBi 880 – 960 MHz +45°, –45° 2 x 17.8 dBi 69° > 25 dB 67° > 25 dB 65° > 25 dB > 25 dB > 14 dB > 25 dB > 14 dB 1.0 dB ±2.0° > 25 dB > 14 dB 8.5° 8.3° 7.8° > 13 dB > 14 dB > 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 < 1.4 < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 790 / 370 / 1090 N 2254 / 259 / 99 mm M (Medium) 11 kg / 13 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter XPol Panel 790–960 65° 17.5dBi 0°–8°T Type No. 80010305V02 s clamped includ 790 – 960 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Average gain (dBi) 16.8 ... 17 ... 16.7 16.9 ... 17.1 ... 16.9 17.2 ... 17.4 ... 17.0 Tilt 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° Horizontal Pattern: Half-power beam width 69° 67° 65° Front-to-back ratio, copolar > 25 dB > 25 dB > 25 dB Cross polar ratio Maindirection 0° Typically: 25 dB Typically: 25 dB Typically: 25 dB Sector ±60° Typically: > 10 dB Typically: > 10 dB Typically: > 10 dB Tracking, Avg. 0.5 dB Squint ±2.5° Vertical Pattern: Half-power beam width 9.1° 8.8° 8.5° Electrical tilt 0°– 8°, continuously adjustable Sidelobe suppression for first 0° ... 2° ... 4° ... 8° T 0° ... 2° ... 4° ... 8° T 0° ... 2° ... 4° ... 8° T sidelobe above main beam 18 ... 18 ... 18 ... 16 dB 18 ... 18 ... 18 ... 16 dB 20 ... 18 ... 17 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 22 < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 800 / 390 / 1090 N 2254 / 259 / 99 mm M (Medium) 11.5 kg / 13.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 65° 18dBi 0°T Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° ±60° Sector Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above main beam Null-fill VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790 – 866 MHz +45°, –45° 2 x 17.7 dBi 65° s clamped d lu c in 80010215V01 790 – 960 824 – 894 MHz +45°, –45° 2 x 17.9 dBi 880 – 960 MHz +45°, –45° 2 x 18 dBi 67° > 25 dB > 25 dB > 12 dB 0.5 dB ±2.0° 65° > 25 dB > 25 dB > 12 dB 7.4° 7.2° 6.8° ≥ 14 dB ≥ 15 dB Typically: –25 dB ≥ 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Type No. Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply X 69° > 25 dB > 25 dB > 12 dB XPol Panel 790–960 65° 18dBi 6°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam Null-fill 790 – 960 790 – 866 MHz +45°, –45° 2 x 17.7 dBi s clamped includ 80010208V01 790 – 960 824 – 894 MHz +45°, –45° 2 x 17.9 dBi 880 – 960 MHz +45°, –45° 2 x 18 dBi 69° > 25 dB > 25 dB > 10 dB 67° > 25 dB > 25 dB > 10 dB 0.5 dB ±2.5° 65° > 25 dB > 25 dB > 10 dB 7.4° 7.2° 6°, fixed 6.8° ≥ 16 dB ≥ 17 dB Typically: –25 dB ≥ 17 dB 50 Ω < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 23 Panel Dual Polarization Half-power Beam Width 790 – 960 X 65° XPol Panel 790–960 65° 17.5dBi 0°–10°T Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790 – 862 MHz +45°, –45° 17.0 ... 17.1 ... 17.0 0.5° ... 5° ... 9.5° 68° > 24 dB Typically: 23 dB Typically: > 10 dB 24 66° > 25 dB Typically: 23 dB Typically: > 10 dB 1.0 dB ±2.0° 880 – 960 MHz +45°, –45° 17.3 ... 17.4 ... 17.3 0.5° ... 5° ... 9.5° 65° > 25 dB Typically: 25 dB Typically: > 10 dB 7.5° 7.3° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T ≥ 17 ... 14 ... 14 dB ≥ 18 ... 15 ... 15 dB ≥ 20 ... 18 ... 18 dB < 1.5 > 30 dB < –153 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female (long neck) Bottom 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 940 / 440 / 1270 N 2574 / 259 / 99 mm H (Heavy) 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Type No. VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790 – 960 824 – 894 MHz +45°, –45° 17.1 ... 17.2 ... 17.1 0.5° ... 5° ... 9.5° s clamped d lu c in 7.7° XPol Panel 790–960 65° 18dBi 0°–10°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 80010306V02 790 – 862 MHz +45°, –45° 17.4 ... 17.5 ... 17.4 0.5° ... 5° ... 9.5° 68° > 24 dB Typically: 22 dB Typically: > 10 dB 80010307V01 790 – 960 824 – 894 MHz +45°, –45° 17.5 ... 17.6 ... 17.5 0.5° ... 5° ... 9.5° 67° > 25 dB Typically: 23 dB Typically: > 10 dB 1.0 dB ±2.0° s clamped includ 880 – 960 MHz +45°, –45° 17.7 ... 17.9 ... 17.7 0.5° ... 5° ... 9.5° 65° > 25 dB Typically: 25 dB Typically: > 10 dB 7.7° 7.5° 7.3° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T ≥ 18 ... 15 ... 15 dB ≥ 18 ... 15 ... 15 dB ≥ 18 ... 16 ... 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 13 kg / 15 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 85° 13.5dBi 0°–14°T Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±0°) Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790 – 862 MHz +45°, –45° 13.2 ... 13.3 ... 13.2 0° ... 7° ... 14° 86° > 24 dB > 20 dB Typically: 20 dB > 10 dB 85° s clamped d lu c in 80010308V01 790 – 960 824 – 894 MHz +45°, –45° 13.3 ... 13.4 ... 13.3 0° ... 7° ... 14° 85° > 24 dB > 22 dB Typically: 20 dB > 10 dB 0.5 dB ±1.5° 880 – 960 MHz +45°, –45° 13.4 ... 13.5 ... 13.4 0° ... 7° ... 14° 83° > 26 dB > 24 dB Typically: 20 dB > 10 dB 15.5° 15° 0°– 14°, continuously adjustable 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T ≥ 17 ... 16 ... 15 dB ≥ 17 ... 17 ... 16 dB ≥ 17 ... 16 ... 16 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 430 / 200 / 590 N 1294 / 259 / 99 mm M (Medium) 9 kg / 11 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Type No. VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load Height/width/depth Category of mounting hardware Weight Scope of supply X 16° XPol Panel 790–960 85° 15dBi 0°–10°T Frequency range Polarization Average Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±0°) Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam: Avg.: 790 – 960 790 – 862 MHz +45°, –45° 14.8 ... 15.0 ... 14.6 0° ... 5° ... 10° 85° > 25 dB > 21 dB Typically: 23 dB > 10 dB s clamped includ 80010309V01 790 – 960 824 – 894 MHz +45°, –45° 14.9 ... 15.1 ... 14.7 0° ... 5° ... 10° 85° > 25 dB > 21 dB Typically: 22 dB > 10 dB 0.5 dB ±3.0° 880 – 960 MHz +45°, –45° 14.8 ... 15.2 ... 15.0 0° ... 5° ... 10° 83° > 26 dB > 21 dB Typically: 22 dB > 10 dB 10.1° 9.8° 9.6° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T ≥ 15 ... 15 ... 14 dB ≥ 15 ... 15 ... 15 dB ≥ 18 ... 18 ... 18 dB ≥ 19 ... 19 ... 19 dB ≥ 20 ... 20 ... 20 dB ≥ 22 ... 22 ... 22 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 680 / 310 / 900 N (at 150 km/h) 1934 / 259 / 99 mm M (Medium) 11.5 kg / 13.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 25 Panel Dual Polarization Half-power Beam Width 790 – 960 X 85° XPol Panel 790–960 85° 17dBi 0°T 80010217V01 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±0°) Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790 – 960 824 – 894 MHz +45°, –45° 16.7 dBi 790 – 862 MHz +45°, –45° 16.6 dBi 85° > 25 dB > 24 dB > 20 dB > 15 dB 1.0 dB ±4.5° 83° > 25 dB > 24 dB > 20 dB > 13 dB 7.5° 7.3° 7.0° 16 dB 17 dB 16 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Type No. VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 26 880 – 960 MHz +45°, –45° 16.8 dBi 86° > 25 dB > 23 dB > 20 dB > 15 dB XPol Panel 790–960 85° 16dBi 0°–10°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±0°) Front-to-back ratio (180°±30°) 0° Cross polar ratio Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam s clamped d lu c in 790 – 862 MHz +45°, –45° 15.8 ... 15.6 ... 15.4 0.5° ... 5° ... 9.5° 86° > 24 dB > 20 dB Typically: 20 dB > 10 dB 80010310V01 790 – 960 824 – 894 MHz +45°, –45° 16.0 ... 15.9 ... 15.8 0.5° ... 5° ... 9.5° 85° > 24 dB > 22 dB Typically: 20 dB > 10 dB 0.5 dB ±3.5° s clamped includ 880 – 960 MHz +45°, –45° 16.2 ... 16.2 ... 16.2 0.5° ... 5° ... 9.5° 83° > 26 dB > 24 dB Typically: 20 dB > 10 dB 8.1° 7.9° 7.6° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T ≥ 18 ... 14 ... 14 dB ≥ 18 ... 17 ... 16 dB ≥ 17 ... 16 ... 16 dB < 1.5 > 30 dB < –153 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 950 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Panel Dual Polarization Half-power Beam Width XPol Panel 790–960 85° 16.5dBi 0°–10°T Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±0°) Front-to-back ratio (180°±30°) 0° Cross polar ratio Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790 – 862 MHz +45°, –45° 16.2 ... 16.2 ... 15.8 0.5° ... 5° ... 9.5° 85° > 24 dB > 21 dB Typically: 20 dB > 10 dB 790 – 960 X 85° s clamped d lu c in 80010300V01 790 – 960 824 – 894 MHz +45°, –45° 16.3 ... 16.3 ... 16.1 0.5° ... 5° ... 9.5° 85° > 25 dB > 23 dB Typically: 20 dB > 10 dB 0.5 dB ±3.5° 880 – 960 MHz +45°, –45° 16.5 ... 16.6 ... 16.5 0.5° ... 5° ... 9.5° 83° > 26 dB > 24 dB Typically: 20 dB > 10 dB 8° 7.8° 7.6° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T ≥ 18 ... 15 ... 14 dB ≥ 18 ... 17 ... 16 dB ≥ 18 ... 16 ... 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female Rearside 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 940 / 420 / 1270 N 2574 / 259 / 99 mm H (Heavy) 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 27 28 Summary – Directional Antennas XPol 1710...2690 MHz Dual Polarization +45°/–45° Type Type No. Height [mm] XPol Panel 1710–2170 30° 21dBi 0°–8°T 742351V01 1304 XPol Panel 1710–2690 65° 9.5dBi 0°T 80010711 XPol Panel 1710–2690 65° 12dBi 4°T XPol Panel 1710–2170 65° 16dBi XPol Panel 1710–2690 65° XPol Panel XPol Panel XPol Panel XPol Panel XPol Panel 1710–2200 1710–2170 1710–2200 1710–2200 1710–2690 XPol Panel XPol Panel Connector position Page bottom 30 155 bottom or top 31 80010761 278 bottom 31 0°T 742196V01 735 bottom or top 32 16.5dBi 0°–12°T 80010681 851 bottom 33 65° 65° 65° 65° 65° 18.3dBi 18dBi 18dBi 18dBi 18dBi 0°T 0°–8°T 0°–10°T 0°–15°T 0°–12°T 80010425V01 742214V01 742215V01 80010504V01 80010621V01 1302 1142 1314 1387 1410 bottom bottom bottom bottom bottom 34 34 35 36 37 1710–2200 1710–2690 65° 65° 19.5dBi 19dBi 0°–6°T 0°–6°T 742213V01 80010651 1954 1670 bottom bottom 38 39 XPol Panel XPol Panel 1710–2200 1710–2200 65° 62° 21dBi 21.2dBi 0°T 0°–6°T 80010439V01 80010378 2172 2548 bottom or top bottom 40 40 XPol Panel 1710–2170 90° 11.5dBi 0°T 741984V01 342 bottom or top 41 XPol Panel 1710–2690 85° 17dBi 2°–10°T 80010679 1390 bottom 42 XPol Panel 1710–2170 90° 18dBi 0°–6°T 741990V01 1942 bottom 43 80010605 698 bottom 44 bottom 45 ESLS ESLS HE HE Antennas with Dual-Beam XXPol Panel 1710–2200 1710–2200 40° (–30°) 40° (+30°) 17dBi 17dBi 2°–14°T 2°–14°T XXPol Panel 1710–2200 1710–2200 45° (–30°) 45° (+30°) 19.5dBi 19.5dBi 0°–10°T 80010606V01 0°–10°T 1314 Tri-Sector Pipe Antenna XPol Tri-Sector Pipe 1710–2170 65° 15.5dBi 0°–12°T 80010375 1241 bottom 46 XPol Tri-Sector Pipe 1710–2170 65° 18dBi 0°–10°T 80010360 1823 bottom 47 Flexible Sealing Frame 85010010 48 New or changed product Abbreviations: ESLS: Enhanced Side Lobe Suppression (above or below horizon) HE: High Efficiency (Antennas with high gain compared to length) 29 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2170 X 30° XPol Panel 1710–2170 30° 21dBi 0°–8°T Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Sidelobe suppression Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 30 742351V01 s clamped includ 1710 – 1880 MHz +45°, –45° 2 x 20.2 dBi 1710 – 2170 1850 – 1990 MHz +45°, –45° 2 x 20.5 dBi 1920 – 2170 MHz +45°, –45° 2 x 20.7 36° > 30 dB 35° > 30 dB 33° > 30 dB Typically: 20 dB > 10 dB > 14 dB Typically: 20 dB > 10 dB > 14 dB 0.5 dB ±1.0° Typically: 20 dB > 10 dB > 14 dB 7.4° 7.0° 6.7° 0°– 8°, continuously adjustable 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 18 ... 17 ... 16 dB 18 ... 18 ... 17 dB 18 ... 17 ... 16 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 540 / 135 / 640 N 1304 / 299 / 69 mm M (Medium) 14 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width XPol Panel 1710–2690 65° 9.5dBi Type No. Frequency range 1710 – 1990 MHz Polarization +45°, –45° Gain 8.7 dBi Horizontal Pattern: Half-power beam width Approx. 67° Front-to-back ratio, copolar > 24 dB (180°±30°) Cross polar ratio 0° Typically: 20 dB > 10 dB Cross polar ratio ±60° sector corner Vertical Pattern: Half-power beam width Approx. 66° VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Max. wind velocity Height/width/depth Category of mounting hardware Weight Scope of supply Type No. VSWR Isolation, between ports Intermodulation IM3 Max. power per input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply X 65° 80010711 s clamped d lu c in 1710 – 2690 1920 – 2200 MHz 2200 – 2490 MHz +45°, –45° +45°, –45° 9.2 dBi 9.6 dBi 2490 – 2690 MHz +45°, –45° 9.8 dBi Approx. 62° > 24 dB Approx. 55° > 22 dB Approx. 53° > 22 dB Typically: 20 dB > 9 dB Typically: 24 dB > 8 dB Typically: 24 dB > 8 dB Approx. 60° Approx. 55° Approx. 53° < 1.5 > 27 dB < –150 dBc (2 x 43 dBm carrier) 150 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 50 / 13 / 55 N 200 km/h 155 / 155 / 69 mm L (Light) 1.5 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter XPol Panel 1710–2690 65° 12dBi 4°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt 1710 – 2690 1710 – 1990 MHz +45°, –45° 2 x 11 dBi 80010761 1710 – 2690 1920 – 2200 MHz 2200 – 2490 MHz +45°, –45° +45°, –45° 2 x 11.5 dBi 2 x 12.2 dBi s clamped includ 2490 – 2690 MHz +45°, –45° 2 x 12.7 dBi 67° > 30 dB 65° > 28 dB 60° > 28 dB 58° > 27 dB Typically: > 20 dB > 8 dB Typically: > 20 dB > 8 dB Typically: > 20 dB > 8 dB Typically: > 20 dB > 8 dB 36° 3°, fixed 31° 3°, fixed 25° 4°, fixed 25° 4°, fixed < 1.5 > 28 dB < –150 dBc (2 x 43 dBm carrier) 150 W (at 50 °C ambient temperature) Bottom Frontal / lateral / rearside: 75 / 17 / 75 N 278 / 154 / 69 mm L (Light) 1.8 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter For more information about additional mounting accessories please refer to page 191 31 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2170 X 65° XPol Panel 1710–2170 65° 16dBi 0°T 742196V01 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Maindirection Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 32 s clamped d lu c in 1710 – 1880 MHz +45°, –45° 2 x 15.3 dBi 1710 – 2170 1850 – 1990 MHz +45°, –45° 2 x 15.6 dBi 1920 – 2170 MHz +45°, –45° 2 x 15.8 dBi 67° Copolar: > 30 dB Total power: > 25 dB 66° Copolar: > 30 dB Total power: > 25 dB 64° Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0.5 dB ±1.5° Typically: 25 dB > 10 dB 12.6° 11.8° 11° > 14 dB > 16 dB > 14 dB < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 185 / 65 / 220 N 735 / 155 / 69 mm L (Light) 4.5 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2690 X 65° XPol Panel 1710–2690 65° 16.5dBi 0°–12°T Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression – for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped d lu c in 80010681 Type No. 1710 – 1990 MHz +45°, –45° 2 x 15.5 dBi 67° > 25 dB Typically: 25 dB > 10 dB 10.8° 0° ... 6° ... 12° T ≥ 12 ... 13 ... 15 dB 1710 – 2690 1920 – 2200 MHz 2200 – 2490 MHz +45°, –45° +45°, –45° 2 x 16.3 dBi 2 x 16.7 dBi 64° > 25 dB Typically: 28 dB > 8 dB 60° > 23 dB Typically: 28 dB > 8 dB 9.9° 8.8° 0°– 12°, continuously adjustable 0° ... 6° ... 12° T 0° ... 6° ... 12° T ≥ 13 ... 14 ... 15 dB ≥ 13 ... 14 ... 16 dB 2490 – 2690 MHz +45°, –45° 2 x 16.7 dBi 60° > 23 dB Typically: 28 dB > 11 dB 8.4° 0° ... 6° ... 12° T ≥ 15 ... 15 ... 17 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 210 / 60 / 220 N 851 / 155 / 70 mm L (Light) 5 kg / 5.2 kg (clamps incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter For more information about additional mounting accessories please refer to page 191 33 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2170/2200 X 65° XPol Panel 1710–2200 65° 18.3dBi 0°T 80010425V01 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam First null-fill below main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1710 – 1880 MHz +45°, –45° 2 x 17.9 dBi 66° > 30 dB Typically: 20 dB > 10 dB 0.5 dB ±1.5° 64° > 30 dB Typically: 20 dB > 10 dB 6.6° 5.8° > 14 dB 6.2° 0°, fixed > 15 dB > 16 dB Typically: 25 dB Typically: 25 dB Typically: 25 dB < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom Frontal / lateral / rearside: 330 / 115 / 390 N 1302 / 155 / 69 mm M (Medium) 7 kg / 9 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Type No. VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 34 1920 – 2200 MHz +45°, –45° 2 x 18.3 dBi 67° > 30 dB Typically: 20 dB > 10 dB XPol Panel 1710–2170 65° 18dBi 0°–8°T Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio 0° Maindirection Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above horizon, Avg. 1710 – 2200 1850 – 1990 MHz +45°, –45° 2 x 18.1 dBi s clamped includ 742214V01 s clamped includ 1710 – 1880 MHz +45°, –45° 2 x 17.5 dBi 1710 – 2170 1850 – 1990 MHz +45°, –45° 2 x 17.7 dBi 1920 – 2170 MHz +45°, –45° 2 x 18 dBi 66° Copolar: 30 dB 64° Copolar: 30 dB 62° Copolar: 30 dB Avg.: 25 dB > 10 dB Avg.: 25 dB > 10 dB 1.0 dB ±2.5° Avg.: 28 dB > 10 dB 8.3° 7.8° 7.4° 0°– 8°, continuously adjustable 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 20 ... 20 ... 20 dB 20 ... 20 ... 20 dB 20 ... 20 ... 20 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 290 / 80 / 300 N 1142 / 155 / 70 mm L (Light) 4.5 kg / 6.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width XPol Panel 1710–2200 65° 18dBi 0°–10°T Type No. 1710 – 2200 X 65° s clamped includ 742215V01 1710 – 1880 MHz +45°, –45° 17.7 ... 17.8 ... 17.6 0° ... 5° ... 10° 1710 – 2200 1850 – 1990 MHz +45°, –45° 18.0 ... 18.2 ... 17.9 0° ... 5° ... 10° 1920 – 2200 MHz +45°, –45° 18.1 ... 18.2 ... 18.0 0° ... 5° ... 10° 68° Copolar: > 30 dB Totel power: > 25 dB 66° Copolar: > 30 dB Totel power: > 25 dB 64° Copolar: > 30 dB Totel power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0.5 dB ±1.5° Typically: 25 dB > 10 dB Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Maindirection Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam 6.8° 6.4° 0°– 10°, continuously adjustable 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 18 ... 18 ... 17 ... 17 dB 18 ... 18 ... 17 ... 17 dB 18 ... 18 ... 17 ... 17 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 330 / 90 / 340 N 1314 / 154 / 70 mm L (Light) 5.2 kg / 7.2 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 7.1° For more information about additional mounting accessories please refer to page 191 35 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2200 X 65° XPol Panel 1710–2200 65° 18dBi 0°–15°T ESLS Type No. 80010504V01 s clamped d lu c in 1710 – 2200 Frequency range 1710 – 1880 MHz 1880 – 1990 MHz 1920 – 2170 MHz 2000 – 2200 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain at 0° tilt 2 x 17.5 dBi 2 x 17.6 dBi 2 x 17.7 dBi 2 x 17.8 dBi Horizontal Pattern: Half-power beam width 68° 66° 64° 62° Front-to-back ratio (180°±30°) ≥ 25 dB ≥ 25 dB ≥ 25 dB ≥ 25 dB 0° Cross polar ratio 22 dB 22 dB 24 dB 26 dB Sector ±60° ≥ 10 dB ≥ 10 dB ≥ 10 dB ≥ 10 dB 1.0 dB Tracking, Avg. Squint ±2.0° Vertical Pattern: Half-power beam width 7.9° 7.5° 7.2° 7.0° Electrical tilt 0°– 15°, continuously adjustable Sidelobe suppression 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T – for first sidelobe above main beam ≥ 17 ... 20 ... 18 ... 17 dB ≥ 16 ... 20 ... 18 ... 17 dB ≥ 16 ... 20 ... 18 ... 17 dB ≥ 15 ... 20 ... 18 ... 15 dB – within 0°–20° sector above horizon ≥ 16 ... 18 ... 18 ... 16 dB ≥ 16 ... 18 ... 17 ... 16 dB ≥ 15 ... 18 ... 17 ... 16 dB ≥ 15 ... 16 ... 16 ... 15 dB Null-fill at 0° tilt 21 dB 20 dB 19 dB 18 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 36 < 1.5 > 30 dB < –153 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 360 / 100 / 370 N 1387 / 155 / 69 mm L (Light) 6.5 kg / 8.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2690 X 65° XPol Panel 1710–2690 65° 18dBi 0°–12°T ESLS Type No. Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° ±60° Sector Tracking, Avg. Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression – for first sidelobe above main beam – within 0°–20° sector above horizon VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind loa (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1710 – 1990 MHz +45°, –45° 17.4 ... 17.4 ... 17.3 0° ... 6° ... 12° 68° > 25 dB Typically: 25 dB > 10 dB 7.1° 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB ≥ 17 ... 17 ... 16 dB s clamped d lu c in 80010621V01 1710 – 2690 1920 – 2200 MHz 2200 – 2490 MHz +45°, –45° +45°, –45° 18.2 ... 18.0 ... 17.9 18.2 ... 18.1 ... 17.7 0° ... 6° ... 12° 0° ... 6° ... 12° 64° > 25 dB Typically: 25 dB > 10 dB 1.0 dB 2490 – 2690 MHz +45°, –45° 18.3 ... 18.0 ... 17.6 0° ... 6° ... 12° 61° > 25 dB Typically: 25 dB > 10 dB 6.5° 5.9° 0°– 12°, continuously adjustable 0° ... 6° ... 12° T 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB ≥ 18 ... 18 ... 18 dB ≥ 17 ... 17 ... 16 dB ≥ 16 ... 18 ... 17 dB 60° > 25 dB Typically: 25 dB > 10 dB 5.7° 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB ≥ 17 ... 17 ... 17 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 370 / 135 / 420 N 1410 / 154 / 70 mm M (Medium) 6.5 kg / 8.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 37 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2200 X 65° XPol Panel 1710–2200 65° 19.5dBi 0°–6°T Type No. 742213V01 s clamped d lu c in 1710 – 1880 MHz +45°, –45° 2 x 19 dBi 1710 – 2200 1850 – 1990 MHz +45°, –45° 2 x 19.2 dBi 1920 – 2200 MHz +45°, –45° 2 x 19.5 dBi 67° Copolar: > 30 dB Total power: > 25 dB 65° Copolar: > 30 dB Total power: > 25 dB 63° Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 0.5 dB ±2.0° Typically: 25 dB > 10 dB Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam 4.5° 4.3° 0°– 6°, continuously adjustable 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T 18 ... 18 ... 16 ... 15 dB 18 ... 18 ... 17 ... 16 dB 18 ... 18 ... 18 ... 18 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 510 / 140 / 510 N 1954 / 155 / 70 mm M (Medium) 9 kg / 11 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 38 4.7° For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width XPol Panel 1710–2690 65° 19dBi 0°–6°T Type No. Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° ±60° Sector Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1710 – 1990 MHz +45°, –45° 2 x 18.5 dBi 67° > 28 dB Typically: 25 dB > 10 dB 5.4° 0° ... 3° ... 6° T ≥ 18 ... 18 ... 17 dB 1710 – 2690 X 65° 80010651 1710 – 2690 1920 – 2170 MHz 2170 – 2490 MHz +45°, –45° +45°, –45° 2 x 19.0 dBi 2 x 19.4 dBi 63° > 28 dB Typically: 25 dB > 10 dB 1.5 dB ±3° 60° > 25 dB Typically: 25 dB > 10 dB 4.9° 4.3° 0°– 6°, continuously adjustable 0° ... 3° ... 6° T 0° ... 3° ... 6° T ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB s clamped d lu c in 2490 – 2690 MHz +45°, –45° 2 x 19.5 dBi 58° > 25 dB Typically: 28 dB > 10 dB 4.0° 0° ... 3° ... 6° T ≥ 18 ... 18 ... 17 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) Bottom 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 430 / 115 / 440 N 1670 / 155 / 70 mm M (Medium) 7 kg / 9 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 39 Panel Dual Polarization Half-power Beam Width 1710 – 2200 X 65° / 62° XPol Panel 1710–2200 65° 21dBi 0°T 80010439V01 Type No. s clamped d lu c in 1710 – 2200 Frequency range 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2000 – 2200 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain 2 x 20.5 dBi 2 x 20.8 dBi 2 x 21.1 dBi 2 x 21.2 dBi Horizontal Pattern: Half-power beam width 66° 63° 60° 58° Front-to-back ratio (180°±30°) > 30 dB > 30 dB > 30 dB > 30 dB Cross polar ratio 0° 25 dB 23 dB 23 dB 23 dB Sector ±60° > 12 dB > 12 dB > 10 dB > 10 dB 0.5 dB Tracking, Avg. Squint ±1.5° Vertical Pattern: Half-power beam width 4.2° 4° 3.7° 3.6° Electrical tilt 0°, fixed Sidelobe suppression > 15 dB – for first sidelobe above main beam > 15 dB – within 0°—30° sector above horizon First null-fill below main beam < 20 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 550 / 210 / 610 N 2172 / 155 / 89 mm M (Medium) 11.5 kg / 13.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter XPol Panel 1710–2200 62° 21.2dBi 0°–6°T Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam Null-fill at 0° tilt VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 40 1710 – 1880 MHz +45°, –45° 2 x 20.6 dBi 65° > 30 dB 25 dB > 10 dB 80010378 1710 – 2200 1850 – 1990 MHz +45°, –45° 2 x 21.1 dBi 62° > 28 dB 23 dB > 10 dB 1.0 dB ±2.5° s clamped includ 1920 – 2200 MHz +45°, –45° 2 x 21.2 dBi 60° > 28 dB 23 dB > 10 dB 3.7° 3.5° 3.3° 0°– 6°, continuously adjustable 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 18 ... 18 ... 17 dB 18 ... 17 ... 17 dB 17 ... 17 ... 17 dB 20 dB 20 dB 20 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1x, Position bottom, continuously adjustable Frontal / lateral / rearside: 660 / 260 / 730 N 2548 / 155 / 89 mm M (Medium) 13 kg / 15 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width XPol Panel 1710–2170 90° 11.5dBi Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° ±60° Sector Tracking, Avg. Squint Vertical Pattern: Half-power beam width Sidelobe supression vertical sector ±45° VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1710 – 2170 X 90° s clamped d lu c in 741984V01 1710 – 1880 MHz +45°, –45° 2 x 11.3 dBi 1710 – 2170 1850 – 1990 MHz +45°, –45° 2 x 11.5 dBi 1920 – 2170 MHz +45°, –45° 2 x 11.6 dBi 86° Copolar: > 23 dB Total power: > 23 dB 87° Copolar: > 23 dB Total power: > 23 dB 88° Copolar: > 23 dB Total power: > 23 dB Typically: 20 dB > 18 dB Typically: 25 dB > 18 dB 0.5 dB ±3.0° Typically: 20 dB > 15 dB 28° 26° 26° > 20 dB > 20 dB > 20 dB < 1.4 > 30 dB < –150 dBc (2 x 43 dBm carrier) 150 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 90 / 27 / 105 N 342 / 155 / 69 mm L (Light) 2 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter For more information about additional mounting accessories please refer to page 191 41 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2690 X 85° XPol Panel 1710–2690 85° 17dBi 2°–10°T Type No. Frequency range Polarization Gain at 2° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Max. wind velocity Height/width/depth Category of mounting hardware Weight Scope of supply 42 1710 – 1990 MHz +45°, –45° 2 x 16.4 dBi 84° > 25 dB Typically: 24 dB > 12 dB 6.9° 2° ... 6° ... 10° T ≥ 18 ... 18 ... 17 dB Preliminary Issue 80010679 1710 – 2690 1920 – 2200 MHz 2200 – 2490 MHz +45°, –45° +45°, –45° 2 x 16.6 dBi 2 x 17.0 dBi 86° > 24 dB Typically: 25 dB > 12 dB 84° > 23 dB Typically: 22 dB > 10 dB 6.0° 5.4° 2°– 10°, continuously adjustable 2° ... 6° ... 10° T 2° ... 6° ... 10° T ≥ 18 ... 18 ... 17 dB ≥ 18 ... 17 ... 17 dB s clamped d lu c in 2490 – 2690 MHz +45°, –45° 2 x 17.0 dBi 82° > 22 dB Typically: 22 dB > 10 dB 5.0° 2° ... 6° ... 10° T ≥ 18 ... 18 ... 18 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 360 / 100 / 370 N 200 km/h 1388 / 155 / 69 mm M (Medium) 6 kg / 8 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width XPol Panel 1710–2170 90° 18dBi 0°–6°T Type No. 1710 – 2170 X 90° s clamped includ 741990V01 1710 – 1880 MHz +45°, –45° 2 x 17.7 dBi 1710 – 2170 1850 – 1990 MHz +45°, –45° 2 x 18 dBi 1920 – 2170 MHz +45°, –45° 2 x 18.2 dBi 88° > 25 dB > 25 dB 88° > 25 dB > 25 dB 88° > 25 dB > 25 dB Typically: 20 dB > 10 dB Typically: 20 dB > 10 dB 0.5 dB ±2.5° Typically: 20 dB > 10 dB Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar total power Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam 4.7° 4.5° 0°– 6°, continuously adjustable 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T 17 ... 17 ... 17 ... 17 dB 18 ... 18 ... 18 ... 18 dB 18 ... 18 ... 18 ... 18 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom 1 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 510 / 185 / 610 N 1942 / 155 / 69 mm M (Medium) 11 kg / 13 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 4.9° For more information about additional mounting accessories please refer to page 191 43 Dual-Beam Panel Dual Polarization Half-power Beam Width 1710 – 2200 1710 – 2200 X X 40° 40° XXPol Panel 1710–2200/1710–2200 40°(–30°)/40°(+30°) 17/17dBi 2°–14°/2°–14°T 1710 – 2200 1850 – 1990 MHz 1920 – 2200 MHz Beam A (–30°), Beam B (+30°) +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 2° ... 7° ... 14° T 2° ... 7° ... 14° T 2° ... 7° ... 14° T 16.5 ... 16.5 ... 16.2 dBi 17.0 ... 16.8 ... 16.5 dBi 17.5 ... 17.4 ... 16.8 dBi Frequency range Azimuth direction Polarization Gain 1710 – 1880 MHz Horizontal Pattern: Half-power beam width (offset beams ±30°) Front-to-back ratio 43° Cross polar ratio –30°; +30° Maindirection Sector –60°; 0°; 0°; +60° Sidelobe suppression for sidelobes beside main beam Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply dB dB 14.5° 14° 2°–14°, continuously adjustable 13° > 16 dB < 1.5 > 28 dB < –150 dBc (2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom Frontal / lateral / rearside: 400 / 115 / 450 N 698 / 380 / 150 mm M (Medium) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 14.5° 3 1710–2200 +45° Beam B (+30°) 1710–2200 +45° Beam A (–30°) 1710–2200 –45° Beam A (–30°) 7-16 7-16 7-16 7-16 dB 10 1710–2200 –45° Beam B (+30°) Vertical0 Pattern Beam A (–30°), Beam B (+30°) 2°–14° electrical downtilt 1850 – 1990 MHz Beam A (–30°) 39° 14° 10 Beam B (+30°) 3 Vertical0 Pattern Beam A (–30°), Beam B (+30°) 2°–14° electrical downtilt 1920 – 2200 MHz 10 3 Typically: 15 dB > 8 dB Beam B (+30°) Horizontal 0 Pattern 36° Typically: 15 dB > 8 dB > 18 dB dB dB 43° 10 3 > 30 dB > 25 dB Typically: 15 dB > 8 dB Beam A (–30°) Horizontal 0 Pattern 39° Copolar: Total power: 37° 1710 – 1880 MHz 10 3 40° 36° Horizontal 0 Pattern Beam A (–30°) Beam B (+30°) 13° 10 3 dB 43° 44 s clamped includ 80010605 Type No. Vertical0 Pattern Beam A (–30°), Beam B (+30°) 2°–14° electrical downtilt For more information about additional mounting accessories please refer to page 191 Dual-Beam Panel Dual Polarization Half-power Beam Width 1710 – 2200 1710 – 2200 X X 45° 45° XXPol Panel 1710–2200/1710–2200 45°(–30°)/45°(+30°) 19.5/19.5dBi 0°–10°/0°–10°T s clamped includ 80010606V01 Type No. 1710 – 2200 1850 – 1990 MHz 1920 – 2200 MHz Beam A (– 30°), Beam B (+30°) +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 4 x 19 dBi 4 x 19.3 dBi 4 x 19.5 dBi Frequency range Azimuth direction Polarization Gain Horizontal Pattern: Half-power beam width (offset beams ±30°) Front-to-back ratio 1710 – 1880 MHz 47° Cross polar ratio Maindirection –30°; +30° –60°; 0°; 0°; +60° Sector Sidelobe suppression for sidelobes beside main beam Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply dB Typically: 18 dB > 13 dB Typically: 17 dB > 13 dB > 18 dB Typically: 16 dB > 13 dB 7.2° 7.1° 0°–10°, continuously adjustable 6.8° > 18 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom Frontal / lateral / rearside: 710 / 200 / 820 N 1314 / 380 / 150 mm M (Medium) 19 kg / 21 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Beam A (–30°) 47° 7.2° 10 Beam B (+30°) Horizontal 0 Pattern 45° > 30 dB > 25 dB 1710 – 1880 MHz 10 3 Copolar: Total power: 43° 3 1710–2200 –45° Beam B (+30°) 1710–2200 +45° Beam B (+30°) 1710–2200 +45° Beam A (–30°) 1710–2200 –45° Beam A (–30°) 7-16 7-16 7-16 7-16 dB 47° 41° Vertical0 Pattern Beam A (–30°), Beam B (+30°) 0°–10° electrical downtilt 1850 – 1990 MHz Beam A (–30°) 7.1° 45° Horizontal 0 Pattern 43° dB Vertical0 Pattern Beam A (–30°), Beam B (+30°) 0°–10° electrical downtilt 1920 – 2200 MHz 10 3 3 dB 3 10 Beam B (+30°) 43° Horizontal 0 Pattern Beam A (–30°) Beam B (+30°) 6.8° 10 3 dB dB 10 Vertical0 Pattern Beam A (–30°), Beam B (+30°) 0°–10° electrical downtilt For more information about additional mounting accessories please refer to page 191 45 0° Tri-Sector Pipe Antenna 1710 –2170 Frequency Range X Dual Polarization 65° Half-power Beam Width Adjust. Electr. Downtilt 0°– 12° 120° 240° 1710 –2170 1710 –2170 X X 65° 65° 0°– 12° 0°– 12° set by hand or by optional RCUs (Remote Control Units) XPol Tri-Sector Pipe 1710–2170 65° 15.5dBi 0°–12°T 80010375 Type No. Electrical datas per sector 1710–2170 Frequencyrange 1710–1880MHz 1850–1990MHz 1920–2170MHz Polarization+45°,–45° +45°,–45° +45°,–45° Gain 0°...4°...8°…12°T 0°...4°...8°…12°T 0°...4°...8°…12°T perInput(dBi) 15.4...15.2...15.0...14.8 15.5...15.4...15.3...14.9 15.7...15.6...15.4...14.9 Half-powerbeamwidth Horizontal: 67° Horizontal: 65° Horizontal: 62° Copolar+45°/ –45°Vertical:12.7° Vertical:12° Vertical: 11.2° Sidelobesuppressionfor 0°...4°...8°…12°T 0°...4°...8°…12°T 0°...4°...8°…12°T firstsidelobeabovehorizon16 ... 16... 15...15dB 18 ... 17... 17...16dB 18 ... 18... 16...16dB Front-to-backratio Copolar:>25dB Copolar:>25dB Copolar:>25dB Crosspolarratio Maindirection 0° Typically:20dB Typically:20dB Typically:20dB Sector ±60° Typically:>10dB Typically:>10dB Typically:>10dB compact servicearea Electricaltilt 0°– 12° 0°– 12° 0°– 12° continuouslyadjustable Isolation:Intrasystem >30dB >30dB >30dB Isolation:Intersystem >40dB >40dB >40dB Impedance50Ω50Ω50Ω VSWR <1.5 <1.5 <1.5 IntermodulationIM3 <–150dBc(2x43dBmcarrier) Max.powerperinput 250W(at50°Cambienttemperature) °  °  Mechanical specifications ° Input3x2x7-16female    ° °   °  °   °  Connectorposition Bottom–insideservicearea  ° Adjustment3x1,Positionbottom mechanismcontinuouslyadjustable insideservicearea Weight 32kg Windload 205N(at150km/h) Max.windvelocity 200km/h Naturalfrequency45–47Hz Dampingratio 0.032 Mechanicalinterface Flangeconnection12x12M atagraduateddiameterof208mm 0°– 360°continuouslyadjustable (forfurtherdetails seeapplicationnote) Packingsize 1395x315x330mm Height/diameter 1241/230and280mm 46 For more information about additional mounting accessories please refer to page 191 0° Tri-Sector Pipe Antenna 1710 –2170 Frequency Range X Dual Polarization 65° Half-power Beam Width Adjust. Electr. Downtilt 0°– 10° 120° 240° 1710 –2170 1710 –2170 X X 65° 65° 0°– 10° 0°– 10° set by hand or by optional RCUs (Remote Control Units) XPol Tri-Sector Pipe 1710–2170 65° 18dBi 0°–10°T 80010360 Type No. Electrical datas per sector 1710–2170 Frequencyrange 1710–1880MHz 1850–1990MHz 1920–2170MHz Polarization+45°,–45° +45°,–45° +45°,–45° Averagegain(dBi) 17.2...17.5...17.217.6...17.8...17.617.8...17.9...17.4 Tilt 0°...5°...10° 0°...5°...10° 0°...5°...10° Half-powerbeamwidth Horizontal: 66° Horizontal: 63° Horizontal: 60° Copolar+45°/ –45°Vertical:7° Vertical:6.7° Vertical:6.4° Electricaltilt 0°– 10° 0°– 10° 0°– 10° continuouslyadjustable Sidelobesuppressionfor 0°...5°...10°T 0°...5°...10°T 0°...5°...10°T firstsidelobeabovehorizon 17 ... 15... 15dB 17 ... 17... 15dB 17 ... 17... 15dB Front-to-backratioCopolar: >30dBCopolar: >30dBCopolar: >30dB (180°±30°) Totalpower:>25dBTotalpower:>25dBTotalpower:>25dB Isolation:Intrasystem >30dB >30dB >30dB Isolation:Intersystem >45dB >42dB >42dB Impedance50Ω50Ω50Ω VSWR <1.5 <1.5 <1.5 IntermodulationIM3 <–150dBc(2x43dBmcarrier) compact servicearea Crosspolarratio Maindirection 0° Typically:25dB Typically:20dB Typically:20dB Sector ±60° Typically:>10dB Typically:>10dB Typically:>10dB Max.powerperinput 300W(at50°Cambienttemperature) °  °  Mechanical specifications ° Input3x2x7-16female    ° °   °  °   °  Connectorposition Bottom–insideservicearea  ° Adjustment3x1,Positionbottom mechanismcontinuouslyadjustable insideservicearea Weight 56kg Windload 320N(at150km/h) Max.windvelocity 200km/h Naturalfrequency19–21Hz Dampingratio 0.032 Mechanicalinterface Flangeconnection12x12M atagraduateddiameterof208mm 0°– 360°continuouslyadjustable (forfurtherdetails seeapplicationnote) Packingsize 2030x400x400mm Height/diameter 1823/230and280mm For more information about additional mounting accessories please refer to page 191 47 Additional Options for Tri-Sector-Antennas Accessories delivered with the Tri-Sector-Pipe Antenna: 1. 2. 3. 4. Clamping ring for mounting the antenna on the customer-supplied base Lightning conductor rod Ring bolt as attachment possibility for lifting aid Wrench (SW41 + SW27) for attaching the RCU Optional Accessories: The following components may be ordered separately 1. 86010147 Remote Control Unit (RCU) 86010148 2. 85010010 Flexible Sealing Frame (Roxtec frame to seal connection between the mast and the antenna, see below 3. 738440 Azimuth Adjustment Tool, see page 205 4. 86010103 3-way power splitter for optional omni pattern Flexible Sealing Frame Type No. Outer diameter Cable diameter (6x) Cable diameter (3x) Frame-Material Sealing-Material Material of screws Accessories Required assembly tools Weight (without packaging) Packing size (L x W x H) 85010010 180 mm 15 – 42 mm 3.5 – 10.5 mm Stainless steel Halogen free cross linkable compound on ethylene-propylene rubber (EPDM) Stainless steel Mounting lubricant Socket wrench size 6 mm 1.8 kg approx. 208 x 208 x 68 mm er: on rmati e und t o f o n n i ation rther For fu rate applic index.htm a cs/ ep r to s in.de/en/m e f e r e pleas ww.kathre w 48 Summary – Directional Antennas XXPol 790...960 MHz Dual Polarization +45°/–45° Type Type No. Height [mm] Connector position Page XXPol Panel 790–862 880–960 65° 65° 14.5dBi 15dBi 0°–12°T 0°–12°T 80010667 1355 bottom 50 XXPol Panel 790–862 880–960 65° 65° 16dBi 16.5dBi 0°–10°T 0°–10°T 80010668 1934 bottom 51 XXPol Panel 790–862 880–960 65° 65° 17dBi 17.5dBi 0°–8°T 0°–8°T 80010669 2574 bottom 52 XXPol Panel 824–960 824–960 60° 60° 16dBi 16dBi 0°–10°T 0°–10°T 80010516V01 2024 rearside 53 XXPol Panel 790–960 790–960 65° 65° 17.5dBi 17.5dBi 0°–8°T 0°–8°T 80010647V01 2254 rearside 54 XXPol Panel 824–960 824–960 65° 65° 17dBi 17dBi 0°–8°T 0°–8°T 80010517V01 2631 rearside 55 XXPol Panel 790–960 790–960 90° 90° 15dBi 15dBi 0°–10°T 0°–10°T 80010816 1934 rearside 56 XXPol Panel 790–960 790–960 90° 90° 16dBi 16dBi 0°–8°T 0°–8°T 80010817 2896 rearside 57 ying , deplo as Whened antenn using r t e s i d l i s e th ers on also crid Combin e s a e pl 279) al Hyb speci (see page 49 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 X X 65° 65° XXPol Panel 790–862/880–960 65°/65° 14.5/15dBi 0°–12°/0°–12°T 80010667 Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, continuously adjustable Sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 50 s clamped includ 790 – 862 790 – 862 MHz +45°, –45° 14.3 ... 14.4 ... 14.1 0° ... 6° ... 12° 880 – 960 880 – 960 MHz +45°, –45° 14.8 ... 15.0 ... 14.6 0° ... 6° ... 12° 68° > 25 dB 64° > 25 dB 20 dB > 10 dB 20 dB > 10 dB 15.2° 0°– 12° 0° ... 6° ... 12° T ≥ 17 ... 16 ... 15 dB 13.9° 0°– 12° 0° ... 6° ... 12° T ≥ 17 ... 15 ... 15 dB < 1.5 > 28 dB, Typ. > 30 dB > 28 dB, Typ. > 30 dB (790 – 862 // 880 – 960 MHz) < –150 dBc (2 x 43 dBm carrier) 350 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 630 / 220 / 730 N 1355 / 303 / 99 mm M (Medium) 14 kg / 16 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 790–862 –45° 790–862 +45° 880–960 –45° 880–960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 X X 65° 65° XXPol Panel 790–862/880–960 65°/65° 16/16.5dBi 0°–10°/0°–10°T 80010668 Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, continuously adjustable Sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped includ 790 – 862 790 – 862 MHz +45°, –45° 15.9 ... 16.0 ... 15.8 0° ... 5° ... 10° 880 – 960 880 – 960 MHz +45°, –45° 16.3 ... 16.6 ... 16.1 0° ... 5° ... 10° 67° > 25 dB 63° > 25 dB 23 dB > 10 dB 25 dB > 10 dB 10° 0°– 10° 0° ... 5° ... 10° T ≥ 17 ... 16 ... 16 dB 9.7° 0°– 10° 0° ... 5° ... 10° T ≥ 18 ... 16 ... 16 dB < 1.5 > 28 dB, Typ. > 30 dB > 28 dB, Typ. > 30 dB (790 – 862 // 880 – 960 MHz) < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 920 / 320 / 1050 N 1934 / 303 / 99 mm M (Medium) 18 kg / 20 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790–862 –45° 790–862 +45° 880–960 –45° 880–960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 51 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 X X 65° 65° XXPol Panel 790–862/880–960 65°/65° 17/17.5dBi 0°–8°/0°–8°T 80010669 Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, continuously adjustable Sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 52 s clamped includ 790 – 862 790 – 862 MHz +45°, –45° 16.6 ... 16.9 ... 16.6 0° ... 4° ... 8° 880 – 960 880 – 960 MHz +45°, –45° 17.1 ... 17.4 ... 17.1 0° ... 4° ... 8° 67° > 25 dB 63° > 25 dB > 25 dB > 10 dB > 23 dB > 10 dB 7.7° 0°– 8° 0° ... 4° ... 8° T ≥ 18 ... 15 ... 15 dB 7.2° 0°– 8° 0° ... 4° ... 8° T ≥ 18 ... 16 ... 15 dB < 1.5 > 28 dB, Typ. > 30 dB > 28 dB, Typ. > 30 dB (790 – 862 // 880 – 960 MHz) < –150 dBc (2 x 43 dBm carrier) 350 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1270 / 430 / 1430 N 2574 / 303 / 99 mm H (Heavy) 18 kg / 20 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790–862 –45° 790–862 +45° 880–960 –45° 880–960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 2-Multi-band Panel Dual Polarization Half-power Beam Width 824 – 960 824 – 960 X X 60° 60° XXPol Panel 824–960/824–960 60°/60° 16/16dBi 0°–10°/0°–10°T 80010516V01 Type No. Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped includ 824 – 960 824 – 894 MHz 880 – 960 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 4 x 15.5 dBi 4 x 15.7 dBi 60° > 25 dB Typically: 15 dB > 10 dB 58° > 25 dB Typically: 16 dB > 10 dB 9.8° 9.3° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T ≥ 14 ... 15 ... 15 dB ≥ 14 ... 15 ... 15 dB < 1.5 Typically: > 25 dB Typically: > 28 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 4 x 7-16 female Rearside, pointing downwards 2 x, Position bottom continuously adjustable Frontal / lateral / rearside: 910 / 300 / 1150 N 2024 / 374 / 169 mm H (Heavy) 23 kg / 25 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 824–960 –45° 824–960 –45° 824–960 +45° 824–960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 53 2-Multi-band Panel Dual Polarization Half-power Beam Width 790 – 960 790 – 960 X X 65° 65° XXPol Panel 790–960/790–960 65°/65° 17.5/17.5dBi 0°–8°/0°–8°T 80010647V01 Type No. s clamped includ 790 – 960 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Average gain (dBi) 16.9 ... 17.1 ... 17.0 17.0 ... 17.2 ... 17.1 17.3 ... 17.4 ... 17.1 Tilt 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° Horizontal Pattern: Half-power beam width 66° 65° 64° Front-to-back ratio, copolar > 27 dB > 27 dB > 27 dB Cross polar ratio Maindirection 0° Typically: 25 dB Typically: 25 dB Typically: 25 dB Sector ±60° Typically: > 10 dB Typically: > 10 dB Typically: > 10 dB Tracking, Avg. 1.0 dB Squint ±2.5° Vertical Pattern: Half-power beam width 9.1° 9.0° 8.5° Electrical tilt 0°– 8°, continuously adjustable Sidelobe suppression for first 0° ... 3° ... 6° ... 8° T 0° ... 3° ... 6° ... 8° T 0° ... 3° ... 6° ... 8° T sidelobe above main beam avg. 18 ... 18 ... 16 ... 15 dB 18 ... 18 ... 16 ... 15 dB 18 ... 18 ... 16 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 54 < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 4 x 7-16 female Rearside 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1760 / 330 / 2040 N 2254 / 576 / 99 mm H (Heavy) 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790 – 960 –45° 790 – 960 +45° 790 – 960 –45° 790 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 2-Multi-band Panel Dual Polarization Half-power Beam Width 824 – 960 824 – 960 X X 65° 65° XXPol Panel 824–960/824–960 65°/65° 17/17dBi 0°–8°/0°–8°T 80010517V01 Type No. Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped includ 824 – 960 824 – 894 MHz 880 – 960 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 4 x 16.5 dBi 4 x 16.7 dBi 66° > 25 dB Typically: 16 dB > 8 dB 61° > 25 dB Typically: 17 dB > 10 dB 7.2° 6.8° 0°– 8°, continuously adjustable 0° ... 4° ... 8° T 0° ... 4° ... 8° T ≥ 15 ... 15 ... 15 dB ≥ 15 ... 16 ... 15 dB < 1.5 Typically: > 25 dB > 28 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 4 x 7-16 female Rearside, pointing downwards 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1210 / 400 / 1540 N 2631 / 374 / 169 mm H (Heavy) 28 kg / 30 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 824–960 –45° 824–960 –45° 824–960 +45° 824–960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 55 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 790 – 960 X X 90° 90° XXPol Panel 790–960/790–960 90°/90° 15/15dBi 0°–10°/0°–10°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±0°) Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 790 – 862 MHz +45°, –45° 14.5 ... 14.5 ... 14.3 0° ... 5° ... 10° 790 – 960 824 – 894 MHz +45°, –45° 14.6 ... 14.8 ... 14.5 0° ... 5° ... 10° 880 – 960 MHz +45°, –45° 14.8 ... 15.0 ... 14.8 0° ... 5° ... 10° 93° > 24 dB > 20 dB Typically: 20 dB > 10 dB 90° > 24 dB > 21 dB Typically: 20 dB > 10 dB 87° > 25 dB > 22 dB Typically: 18 dB > 10 dB 10.5° 10.2° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T ≥ 18 ... 17 ... 16 dB 10° 0° ... 5° ... 10° T ≥ 18 ... 15 ... 14 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (approx.) (at 150 km/h) Height/width/depth Category of mounting hardware Weight (approx.) Scope of supply 56 s clamped includ 80010816 Type No. 0° ... 5° ... 10° T ≥ 18 ... 16 ... 15 dB < 1.5 > 25 dB, Typ. > 27 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 4 x 7-16 female Rearside 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 910 / 380 / 1150 N 1934 / 374 / 106 mm H (Heavy) 17 kg / 19 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790 – 960 –45° 790 – 960 –45° 790 – 960 +45° 790 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 790 – 960 X X 90° 90° XXPol Panel 790–960/790–960 90°/90° 16/16dBi 0°–8°/0°–8°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±0°) Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam s clamped includ 80010817 Type No. 790 – 862 MHz +45°, –45° 15.4 ... 15.4 ... 15.0 0° ... 4° ... 8° 790 – 960 824 – 894 MHz +45°, –45° 15.7 ... 15.7 ... 15.4 0° ... 4° ... 8° 880 – 960 MHz +45°, –45° 16.0 ... 16.1 ... 15.9 0° ... 4° ... 8° 93° > 24 dB > 20 dB Typically: 20 dB > 10 dB 90° > 24 dB > 21 dB Typically: 20 dB > 10 dB 87° > 25 dB > 22 dB Typically: 18 dB > 10 dB 7.4° 7.2° 0°– 8°, continuously adjustable 0° ... 4° ... 8° T ≥ 17 ... 17 ... 15 dB 6.9° 0° ... 4° ... 8° T ≥ 17 ... 17 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 0° ... 4° ... 8° T ≥ 17 ... 17 ... 15 dB < 1.5 Intrasystem: > 27 dB, Intersystem: > 27 dB < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1270 / 400 / 1710 N 2631 / 374 / 106 mm H (Heavy) 23 kg / 25 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790 – 960 –45° 790 – 960 –45° 790 – 960 +45° 790 – 960 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 57 58 Summary – Directional Antennas XXPol 1710...2690 MHz Dual Polarization +45°/–45° Type Type No. Height [mm] Connector position Page XXPol Panel 1710–2690 1710–2690 65° 65° 16.5dBi 16.5dBi 0°–12°T 0°–12°T 80010682 855 bottom 60 XXPol Panel 1710–1880 1920–2170 65° 60° 17.5dBi 18dBi 2°–10°T 2°–10°T 80010744 1410 bottom 61 XXPol Panel 1710–2170 1710–2170 65° 65° 18dBi 18dBi 0°–8°T 0°–8°T 742237 1147 bottom 61 XXPol Panel 1710–2170 2490–2690 65° 60° 18dBi 18dBi 0°–10°T 0°–10°T 80010644 1410 bottom 62 XXPol Panel 1710–2200 1710–2200 65° 65° 18dBi 18dBi 0°–10°T 0°–10°T 742236V01 1319 bottom 63 XXPol Panel 1710–2690 1710–2690 65° 65° 18dBi 18dBi 0°–12°T 0°–12°T ESLS 80010622 1415 bottom 64 XXPol Panel 1710–2200 1710–2200 65° 65° 18dBi 18dBi 0°–15°T 0°–15°T ESLS 80010510V01 1389 bottom 65 XXPol Panel 1710–2170 1710–2170 65° 65° 19.5dBi 19.5dBi 0°–6°T 0°–6°T 742235V01 1959 bottom 66 XXPol Panel 1710–2690 1710–2690 65° 65° 19dBi 19dBi 0°–10°T 0°–10°T 80010652 1668 bottom 67 XXPol Panel 1710–2180 1710–2180 90° 90° 16.5dBi 16.5dBi 0°–10°T 0°–10°T 742352V01 1319 bottom 68 ying deploennas, n e h t W ng ted an er usi the lisso consid ombiners l dC ea pleas l Dual-ban 0 and 231) 3 a i 2 c s e e sp ag (see p Abbreviations: ESLS: Enhanced Side Lobe Suppression (above or below horizon) 59 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2690 1710 – 2690 X X 65° 65° XXPol Panel 1710–2690/1710–2690 65°/65° 16.5/16.5dBi 0°–12°/0°–12°T 80010682 Type No. Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Sector Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam 1710 – 1990 MHz +45°, –45° 4 x 15.8 dBi 0° ±60° VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 60 65° > 30 dB Typically: 25 dB > 8 dB 11° 0° ... 6° ... 12° T ≥ 12 ... 13 ... 15 dB 1710 – 2690 1920 – 2200 MHz 2200 – 2490 MHz +45°, –45° +45°, –45° 4 x 16.2 dBi 4 x 16.6 dBi 64° > 30 dB Typically: 25 dB > 8 dB 60° > 30 dB Typically: 25 dB > 10 dB 10° 9° 0°–12°, continuously adjustable 0° ... 6° ... 12° T 0° ... 6° ... 12° T ≥ 13 ... 14 ... 16 dB ≥ 13 ... 15 ... 16 dB s clamped d lu c in 2490 – 2690 MHz +45°, –45° 4 x 16.7 dBi 61° > 28 dB Typically: 25 dB > 10 dB 8.7° 0° ... 6° ... 12° T ≥ 15 ... 15 ... 17 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 440 / 100 / 460 N 855 / 323 / 71 mm M (Medium) 11 kg / 13 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width 1710...(1880)...2170 1710...(1920)...2170 X X 65° 60° XXPol Panel 1710–1880/1920–2170 65°/60° 17.5/18dBi 2°–10°/2°–10°T Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt, continuously adjustable Sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped d lu c in 80010744 Type No. 1710 – 1880 1710 – 1880 MHz +45°, –45° 2 x 17.5 dBi 65° Copolar: Total power: 1920 – 2170 1920 – 2170 MHz +45°, –45° 2 x 18 dBi > 28 dB > 25 dB 59° Copolar: > 28 dB Total power: > 25 dB Typically: 25 dB > 10 dB 0.6 dB ±1.5° Typically: 25 dB > 10 dB 0.6 dB ±1.5° 6.6° 2°– 10° 2° ... 6° ... 10° T 18 ... 16 ... 16 dB 5.9° 2°– 10° 2° ... 6° ... 10° T 18 ... 16 ... 16 dB < 1.5 > 30 dB < 1.5 > 30 dB < –150 dBc 200 W* > 30 dB < –150 dBc 200 W* 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 370 / 145 / 400 N 1410 / 155 / 89 mm M (Medium) 9 kg / 11 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) XXPol Panel 1710–2170/1710–2170 65°/65° 18/18dBi 0°–8°/0°–8°T Type No. 742237 s clamped d lu c in 1710 – 2170 Frequency range 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz Polarization +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain 4 x 17.5 dBi 4 x 17.7 dBi 4 x 18 dBi Horizontal Pattern: Half-power beam width 65° 63° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB Cross polar ratio Maindirection 0° Avg.: 25 dB Avg.: 25 dB Avg.: 25 dB Sector ±60° > 10 dB > 10 dB > 10 dB Vertical Pattern: Half-power beam width 8.3° 8° 7.5° Electrical tilt 0°–8°, continuously adjustable Sidelobe suppression for first 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T sidelobe above main beam, Avg. 20 ... 20 ... 18 dB 20 ... 20 ... 18 dB 20 ... 20 ... 18 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 590 / 135 / 610 N 1147 / 323 / 71 mm M (Medium) 12.5 kg / 14.5 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 61 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2170 2490 – 2690 X X 65° 60° XXPol Panel 1710–2170/2490–2690 65°/60° 18/18dBi 0°–10°/0°–10°T 80010644 Type No. Frequency range Polarization Gain at 0° tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, continuously adjustable Sidelobe supression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 62 1710 – 2180 1710 – 1990 MHz 1920 – 2170 MHz +45°, –45° +45°, –45° 2 x 17.5 dBi 2 x 17.7 dBi 68° > 25 dB Typically: 25 dB > 8 dB 6.7° 0°–10° 0° ... 5° ... 10° T ≥ 17 ... 17 ... 16 dB s clamped d lu c in 2490 – 2690 2490 – 2690 MHz +45°, –45° 2 x 18.0 dBi 65° > 25 dB Typically: 25 dB > 8 dB 61° > 25 dB Typically: 25 dB > 10 dB 6.3° 5.4° 0°–10° 0° ... 5° ... 10° T ≥ 17 ... 17 ... 16 dB 0° ... 5° ... 10° T ≥ 17 ... 17 ... 16 dB < 1.5 < 1.5 > 30 dB > 30 dB > 29 dB > 29 dB < –150 dBc < –150 dBc (2 x 43 dBm carrier) (2 x 43 dBm carrier) 200 W* 200 W* 400 W* 400 W* 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 370 / 145 / 400 N 1410 / 155 / 89 mm M (Medium) 10 kg / 12 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter *(at 50 °C ambient temperature) For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2200 1710 – 2200 X X 65° 65° XXPol Panel 1710–2200/1710–2200 65°/65° 18/18dBi 0°–10°/0°–10°T 742236V01 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped d lu c in 1710 – 2200 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2200 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 4 x 17.6 dBi 4 x 17.8 dBi 4 x 18 dBi 64° > 30 dB Copolar: Total power: > 25 dB 64° Copolar: > 30 dB Total power: > 25 dB 62° Copolar: > 30 dB Total power: > 25 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB Typically: 25 dB > 10 dB 7° 6.8° 6.5° 0°–10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 20 ... 18 ... 16 dB 20 ... 18 ... 16 dB 16 ... 18 ... 16 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 660 / 155 / 690 N 1319 / 323 / 71 mm M (Medium) 15 kg / 17 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 63 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2690 1710 – 2690 X X 65° 65° XXPol Panel 1710–2690/1710–2690 65°/65° 18/18dBi 0°–12°/0°–12°T ESLS Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression – for first sidelobe above main beam – within 0°–20° sector above horizon VSWR Isolation, between ports Intermodulation IM3 Max. power per input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 64 s clamped d lu c in 80010622 Type No. 1710 – 1990 MHz +45°, –45° 17.4 ... 17.4 ... 17.3 0° ... 6° ... 12° 65° > 30 dB Typically: 28 dB > 10 dB 7.1° 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB ≥ 18 ... 17 ... 15 dB 1710 – 2690 1920 – 2200 MHz 2200 – 2490 MHz +45°, –45° +45°, –45° 17.8 ... 17.6 ... 17.5 18.0 ... 17.9 ... 17.5 0° ... 6° ... 12° 0° ... 6° ... 12° 65° > 28 dB Typically: 27 dB > 8 dB 2490 – 2690 MHz +45°, –45°° 18.0 ... 17.7 ... 17.3 0° ... 6° ... 12° 61° > 28 dB Typically: 25 dB > 8 dB 6.5° 5.9° 0°– 12°, continuously adjustable 0° ... 6° ... 12° T 0° ... 6° ... 12° T ≥ 18 ... 18 ... 18 dB ≥ 18 ... 17 ... 17 dB ≥ 17 ... 17 ... 15 dB ≥ 17 ... 18 ... 16 dB 61° > 26 dB Typically: 23 dB > 10 dB 5.7° 0° ... 6° ... 12° T ≥ 18 ... 18 ... 17 dB ≥ 18 ... 18 ... 17 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 720 / 165 / 740 N 1415 / 323 / 71 mm M (Medium) 16 kg / 18 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2200 1710 – 2200 X X 65° 65° XXPol Panel 1710–2200/1710–2200 65°/65° 18/18dBi 0°–15°/0°–15°T ESLS Type No. 80010510V01 s clamped d lu c in 1710 – 2200 Frequency range 1710 – 1880 MHz 1880 – 1990 MHz 1920 – 2170 MHz 2000 – 2200 MHz Polarization +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° Gain at 0° tilt 4 x 17.5 dBi 4 x 17.6 dBi 4 x 17.7 dBi 4 x 17.8 dBi Horizontal Pattern: Half-power beam width 65° 63° 62° 62° Front-to-back ratio (180°±30°) ≥ 30 dB ≥ 30 dB ≥ 30 dB ≥ 28 dB 0° 24 dB 24 dB 24 dB 26 dB Cross polar ratio Sector ±60° ≥ 9 dB ≥ 9 dB > 10 dB ≥ 10 dB Vertical Pattern: Half-power beam width 7.9° 7.5° 7.2° 7.0° Electrical tilt 0°– 15°, continuously adjustable 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T 0° ... 5° ... 10° ... 15° T Sidelobe suppression – for first sidelobe above main beam ≥ 17 ... 20 ... 18 ... 17 dB ≥ 16 ... 20 ... 18 ... 18 dB ≥ 15 ... 19 ... 18 ... 17 dB ≥ 14 ... 18 ... 18 ... 16 dB – within 0°–20° sector above horizon ≥ 16 ... 18 ... 18 ... 16 dB ≥ 16 ... 17 ... 17 ... 16 dB ≥ 15 ... 17 ... 17 ... 16 dB ≥ 14 ... 16 ... 16 ... 15 dB Null-fill at 0° tilt 23 dB 22 dB 21 dB 20 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –153 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 700 / 160 / 720 N 1389 / 323 / 71 mm M (Medium) 17 kg / 19 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 65 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2170 1710 – 2170 X X 65° 65° XXPol Panel 1710–2170/1710–2170 65°/65° 19.5/19.5dBi 0°–6°/0°–6°T 742235V01 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio s clamped d lu c in 1710 – 2170 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 4 x 19 dBi 4 x 19.2 dBi 4 x 19.5 dBi 65° > 30 dB Copolar: Total power: > 25 dB 64° Copolar: > 30 dB Total power: > 25 dB 63° Copolar: > 30 dB Total power: > 24 dB Cross polar ratio Maindirection 0° Typically: 25 dB Typically: 25 dB Typically: 25 dB Sector ±60° > 10 dB > 10 dB > 10 dB Tracking, Avg. 0.5 dB Squint ±2.5° Vertical Pattern: Half-power beam width 4.6° 4.4° 4.2° Electrical tilt 0°– 6°, continuously adjustable Sidelobe suppression for first 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T 0° ... 2° ... 4° ... 6° T sidelobe above main beam 17 ... 17 ... 14 ... 14 dB 17 ... 17 ... 15 ... 15 dB 17 ... 17 ... 15 ... 15 dB VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 66 < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1010 / 220 / 1040 N 1959 / 323 / 71 mm M (Medium) 18 kg / 20 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2690 1710 – 2690 X X 65° 65° XXPol Panel 1710–2690/1710–2690 65°/65° 19/19dBi 0°–10°/0°–10°T Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation, between ports Intermodulation IM3 Max. power per input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped d lu c in 80010652 Type No. 1710 – 1990 MHz +45°, –45° 18.2 ... 18.4 ... 18.0 0° ... 5° ... 10° 65° > 30 dB Typically: 22 dB > 10 dB 5.5° 0° ... 5° ... 10° T ≥ 18 ... 16 ... 15 dB 1710 – 2690 1920 – 2200 MHz 2200 – 2490 MHz +45°, –45° +45°, –45° 18.7 ... 18.9 ... 18.4 18.8 ... 19.0 ... 18.3 0° ... 5° ... 10° 0° ... 5° ... 10° 65° > 26 dB Typically: 22 dB > 10 dB 2490 – 2690 MHz +45°, –45°° 18.7 ... 19.0 ... 18.3 0° ... 5° ... 10° 62° > 28 dB Typically: 22 dB > 10 dB 5.0° 4.3° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T ≥ 18 ... 16 ... 15 dB ≥ 18 ... 16 ... 15 dB 65° > 26 dB Typically: 20 dB > 10 dB 4.0° 0° ... 5° ... 10° T ≥ 18 ... 15 ... 15 dB < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 830 / 320 / 880 N 1668 / 323 / 71 mm M (Medium) 17 kg / 19 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 67 2-Multi-band Panel Dual Polarization Half-power Beam Width 1710 – 2180 1710 – 2180 X X 90° 90° XXPol Panel 1710–2180/1710–2180 90°/90° 16.5/16.5dBi 0°–10°/0°–10°T 742352V01 Type No. Frequency range Polarization Gain (average) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio s clamped includ 1710 – 2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° 16.1 ... 16.3 ... 16.0 dBi 16.2 ... 16.4 ... 16.1 dBi 16.5 ... 16.7 ... 16.2 dBi 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 88° Copolar: > 24 dB Total power: > 24 dB 90° Copolar: > 24 dB Total power: > 24 dB 88° Copolar: > 24 dB Total power: > 24 dB Cross polar ratio 0° Typically: 15 dB Typically: 15 dB Typically: 15 dB Maindirection Sector ±60° > 8 dB > 7.5 dB > 7 dB Tracking, Avg. 0.5 dB Squint 2.5° Vertical Pattern: Half-power beam width 7.4° 7° 6.5° Electrical tilt 0°–10°, continuously adjustable Sidelobe suppression for first 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T 0° ... 4° ... 8° ... 10° T sidelobe above main beam 18 ... 17 ... 16 ... 15 dB 18 ... 17 ... 16 ... 15 dB 17 ... 17 ... 16 ... 15 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 68 < 1.5 > 30 dB > 30 dB < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 4 x 7-16 female Bottom 2 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 660 / 155 / 690 N 1319 / 323 / 71 mm M (Medium) 17 kg / 19 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 Summary – Directional Antennas XPol, XXPol (iRCU) 698...894 / 1710...2170 MHz XPol Type XPol Panel iRCU XPol Panel iRCU XPol Panel iRCU Type No. Height [mm] Connector position Page 698–894 698–894 698–894 65° 65° 65° 15dBi 16dBi 17dBi 0°–16°T 0°–10°T 0°–10°T 80010734V01 80010735V01 80010736V01 1355 1934 2438 bottom bottom bottom 70 71 72 698–894 1710–2170 698–894 1710–2170 698–894 1710–2170 65° 65° 65° 65° 65° 65° 15dBi 17.5dBI 16dBi 18.5dBi 17dBi 18.5dBi 0°–16°T 0°–10°T 0°–10°T 0°–10°T 0°–10°T 0°–10°T 80010764V01 1403 bottom 73 80010765V01 1918 bottom 74 80010766V01 2438 bottom 75 698–894 1710–2170 698–894 1710–2170 698–894 1710–2170 85° 85° 85° 85° 85° 85° 14dBi 16.5dBi 15dBi 17.5dBi 16dBi 17.5dBi 0°–16°T 0°–10°T 0°–10°T 0°–10°T 0°–10°T 0°–10°T 80010721V01 1394 bottom 76 80010722V01 1828 bottom 77 80010723V01 2368 bottom 78 XXPol XXPol Panel iRCU XXPol Panel iRCU XXPol Panel iRCU XXPol Panel iRCU XXPol Panel iRCU XXPol Panel iRCU iRCU specifications (86010149) see page 79 Abbreviations: iRCU: integrated Remote Control Unit 69 Multi-band Panel 698 – 894 Half-power Beam Width 65° X Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XPol Panel iRCU 698–894 65° 15dBi 0°–16°T Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam: Average: Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply iRCU 0°–16° 80010734V01 698 – 806 MHz +45°, –45° 12.05 dBd / 14.2 dBi 698 – 894 s clamped includ 824 – 894 MHz +45°, –45° 12.65 dBd / 14.8 dBi 68° Copolar: > 30 dB Average: 32 dB 65° Copolar: > 30 dB Average: 33 dB Typically: > 24 dB > 10 dB, Avg. 15 dB Typically: > 23 dB > 10 dB, Avg. 16 dB 16° 14.8° 0°– 16°, continuously adjustable 0° ... 8° ... 16° T 0° ... 8° ... 16° T 16 ... 17 ... 17 dB 18 ... 17 ... 16 dB 16 ... 19 ... 20 dB 20 ... 20 ... 20 dB 50 Ω < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Bottom Frontal: 620 N (at 150 km/h) 1550 N (at 150 mph) Lateral: 200 N (at 150 km/h) 500 N (at 150 mph) Rearside: 710 N (at 150 km/h) 1770 N (at 150 mph) 241 km/h (150 mph) 1355 / 303 / 99 mm (53.3 / 11.9 / 3.9 inches) M (Medium) 11 kg (24 lbs) / 13 kg (27 lbs) (clamps incl.) 1430 x 315 x 115 mm (56.3 x 12.4 x 4.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 in iRCU out 8pin 8pin male female 70 698–894 +45° 698–894 –45° 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Multi-band Panel 698 – 894 Half-power Beam Width 65° X Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XPol Panel iRCU 698–894 65° 16dBi 0°–10°T Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam: Average: Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply iRCU 0°–10° 80010735V01 698 – 806 MHz +45°, –45° 13.35 dBd / 15.5 dBi 698 – 894 s clamped includ 824 – 894 MHz +45°, –45° 13.85 dBd / 16 dBi 67° Copolar: > 30 dB Average: 35 dB 65° Copolar: > 30 dB Average: 35 dB Typically: > 25 dB > 11 dB, Avg. 15 dB Typically: > 25 dB > 11 dB, Avg. 15 dB 11.3° 10° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 16 ... 17 ... 17 dB 18 ... 17 ... 16 dB 16 ... 19 ... 20 dB 20 ... 20 ... 20 dB 50 Ω < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Bottom Frontal: 900 N (at 150 km/h) 2260 N (at 150 mph) Lateral: 310 N (at 150 km/h) 760 N (at 150 mph) Rearside: 1030 N (at 150 km/h) 2580 N (at 150 mph) 241 km/h (150 mph) 1934 / 303 / 99 mm (76.1 / 11.9 / 3.9 inches) H (Heavy) 14 kg (30.9 lbs) / 16 kg (35.3 lbs) (clamps incl.) 2136 x 317 x 127 mm (84.1 x 12.5 x 5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 in iRCU out 8pin 8pin male female 698–894 +45° 698–894 –45° 7-16 7-16 For more information about additional mounting accessories please refer to page 191 71 Multi-band Panel 698 – 894 Half-power Beam Width 65° X Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XPol Panel iRCU 698–894 65° 17dBi 0°–10°T Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam: Average: Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply iRCU 0°–10° 80010736V01 698 – 806 MHz +45°, –45° 14.25 dBd / 16.4 dBi 698 – 894 s clamped includ 824 – 894 MHz +45°, –45° 14.85 dBd / 17 dBi 67° Copolar: > 30 dB Average: 35 dB 68° Copolar: > 30 dB Average: 35 dB Typically: > 25 dB > 11 dB, Avg. 15 dB Typically: > 20 dB > 11 dB, Avg. 15 dB 9.5° 8.6° 0.5°– 9.5°, continuously adjustable 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 16 ... 16 ... 16 dB 18 ... 18 ... 17 dB 18 ... 18 ... 17 dB 20 ... 20 ... 20 dB 50 Ω < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 2 x 7-16 female iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Bottom Frontal: 1160 N (at 150 km/h) 2900 N (at 150 mph) Lateral: 390 N (at 150 km/h) 970 N (at 150 mph) Rearside: 1380 N (at 150 km/h) 3450 N (at 150 mph) 241 km/h (150 mph) 2438 / 303 / 99 mm (96 / 11.9 / 3.9 inches) H (Heavy) 17 kg (37.5 lbs) / 19 kg (41.9 lbs) (clamps incl.) 2600 x 315 x 115 mm (102.4 x 12.4 x 4.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 in iRCU out 8pin 8pin male female 72 698–894 +45° 698–894 –45° 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Multi-band Panel 698 – 894 1710 – 2170 X X Half-power Beam Width 65° 65° iRCU iRCU 0°–16° 0°–10° Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XXPol Panel iRCU 698–894/1710–2170 65°/65° 15/17.5dBi 0°–16°/0°–10°T 80010764V01 Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio 698 – 894 698 – 806 MHz 824 – 894 MHz +45°, –45° +45°, –45° 12.15 dBd / 14.3 dBi 12.65 dBd / 14.8 dBi 68° Copolar: > 30 dB Average: 32 dB 65° Copolar: > 27 dB Average: 30 dB Cross polar ratio Maindirection 0° Typically: > 25 dB Typically: > 25 dB Sector ±60° > 10 dB, Avg. 15 dB > 8 dB, Avg. 14 dB Tracking, Avg. 1.5 dB 1.5 dB Squint ±2.5° ±4.0° Vertical Pattern: Half-power beam width 15° 13.5° Electrical tilt 0°– 16°, continuously adjustable Min. sidelobe suppression for 0° ... 8° ... 16° T 0° ... 8° ... 16° T first sidelobe above main beam: 17 ... 16 ... 16 dB 18 ... 16 ... 16 dB Average: 19 ... 19 ... 18 dB 22 ... 20 ... 20 dB Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply s clamped d lu c in 1710 – 2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° +45°, –45° 17.3 dBi 17.5 dBi 61° Copolar: > 30 dB Average: 34 dB 60° Copolar: > 30 dB Average: 34 dB Typically: > 25 dB > 8 dB, Avg. 14 dB 2.0 dB ±4.0° Typically: > 25 dB > 10 dB, Avg. 16 dB 1.0 dB ±1.5° 7.5° 7.5° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 18 ... 17 dB 18 ... 18 ... 17 dB 20 ... 20 ... 20 dB 20 ... 20 ... 20 dB 50 Ω < 1.5 Intrasystem: > 30 dB, Intersystem: > 35 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Bottom Frontal: 690 N (at 150 km/h) 1710 N (at 150 mph) Lateral: 260 N (at 150 km/h) 640 N (at 150 mph) Rearside: 710 N (at 150 km/h) 1770 N (at 150 mph) 241 km/h (150 mph) 1403 / 300 / 152 mm (55.2 / 11.8 / 6 inches) M (Medium) 18.5 kg (40.8 lbs) / 20.5 kg (45.2 lbs) (clamps incl.) 1646 x 322 x 190 mm (64.8 x 12.7 x 7.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 698–894 –45° 1710–2170 –45° 7-16 7-16 long neck iRCU out in iRCU out in 8pin 8pin 8pin 8pin female male female male 698–894 +45° 1710–2170 +45° 7-16 7-16 long neck For more information about additional mounting accessories please refer to page 191 73 Multi-band Panel 698 – 894 1710 – 2170 X X Half-power Beam Width 65° 65° iRCU iRCU 0°–10° 0°–10° Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XXPol Panel iRCU 698–894/1710–2170 65°/65° 16/18.5dBi 0°–10°/0°–10°T 80010765V01 Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio 698 – 894 698 – 806 MHz 824 – 894 MHz +45°, –45° +45°, –45° 13.15 dBd / 15.3 dBi 13.65 dBd / 15.8 dBi 68° Copolar: > 30 dB Average: 34 dB 65° Copolar: > 30 dB Average: 34 dB Cross polar ratio Maindirection 0° Typically: > 25 dB Typically: > 20 dB Sector ±60° > 10 dB, Avg. 16 dB > 10 dB, Avg. 14 dB Tracking, Avg. 1.0 dB 1.5 dB Squint ±2.5° ±3.0° Vertical Pattern: Half-power beam width 11.8° 10.8° Electrical tilt 0°– 10°, continuously adjustable Min. sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T first sidelobe above main beam: 16 ... 16 ... 18 dB 18 ... 18 ... 16 dB Average: 18 ... 20 ... 20 dB 20 ... 22 ... 20 dB Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply s clamped d lu c in 1710 – 2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° +45°, –45° 18 dBi 18.5 dBi 63° Copolar: > 27 dB Average: 34 dB 62° Copolar: > 27 dB Average: 34 dB Typically: > 25 dB > 8 dB, Avg. 15 dB 1.5 dB ±3.0° Typically: > 30 dB > 10 dB, Avg. 15 dB 1.0 dB ±2.5° 5.8° 5.8° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 18 ... 18 ... 18 dB 20 ... 22 ... 20 dB 20 ... 22 ... 20 dB 50 Ω < 1.5 Intrasystem: > 30 dB, Intersystem: > 35 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 2 x 8pin male iRCU out: 2 x 8pin female Bottom Frontal: 950 N (at 150 km/h) 2380 N (at 150 mph) Lateral: 360 N (at 150 km/h) 890 N (at 150 mph) Rearside: 980 N (at 150 km/h) 2460 N (at 150 mph) 241 km/h (150 mph) 1918 / 300 / 152 mm (75.5 / 11.8 / 6.0 inches) H (Heavy) 23.5 kg (51.8 lbs) / 25.5 kg (56.2 lbs) (clamps incl.) 2166 x 322 x 190 mm (85.3 x 12.7 x 7.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 iRCU out in 698–894 –45° iRCU 698–894 +45° 7-16 long neck7-16 8pin male 8pin female 74 in out 1710 –2170 1710 –2170 –45° +45° 7-16 long neck7-16 8pin female 8pin male For more information about additional mounting accessories please refer to page 191 Multi-band Panel 698 – 894 1710 – 2170 X X Half-power Beam Width 65° 65° iRCU iRCU 0°–10° 0°–10° Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XXPol Panel iRCU 698–894/1710–2170 65°/65° 17/18.5dBi 0°–10°/0°–10°T 80010766V01 Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio 698 – 894 698 – 806 MHz 824 – 894 MHz +45°, –45° +45°, –45° 14.25 dBd / 16.4 dBi 14.65 dBd / 16.8 dBi 68° Copolar: > 30 dB Average: 34 dB 65° Copolar: > 30 dB Average: 34 dB Cross polar ratio Maindirection 0° Typically: > 25 dB Typically: > 20 dB Sector ±60° > 10 dB, Avg. 15 dB > 10 dB, Avg. 12 dB Tracking, Avg. 1.0 dB Squint ±2.5° Vertical Pattern: Half-power beam width 9.5° 8.7° Electrical tilt 0°– 10°, continuously adjustable Min. sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T first sidelobe above main beam: 16 ... 16 ... 16 dB 18 ... 18 ... 16 dB Average: 18 ... 20 ... 18 dB 20 ... 20 ... 20 dB Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply s clamped d lu c in 1710 – 2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° +45°, –45° 18 dBi 18.5 dBi 63° Copolar: > 27 dB Average: 34 dB 62° Copolar: > 27 dB Average: 34 dB Typically: > 25 dB Typically: > 30 dB > 8 dB, Avg. 15 dB > 10 dB, Avg. 15 dB 1.5 dB ±3.0° 5.8° 5.8° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 18 ... 18 dB 18 ... 18 ... 18 dB 20 ... 22 ... 20 dB 20 ... 22 ... 20 dB 50 Ω < 1.5 Intrasystem: > 30 dB, Intersystem: > 35 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 1 x 8pin male iRCU out: 1 x 8pin female Bottom Frontal: 1270 N (at 150 km/h) 3170 N (at 150 mph) Lateral: 470 N (at 150 km/h) 1160 N (at 150 mph) Rearside: 1320 N (at 150 km/h) 3310 N (at 150 mph) 241 km/h (150 mph) 2438 / 300 / 152 mm (96 / 11.8 / 6.0 inches) H (Heavy) 26.5 kg (58.3 lbs) / 28.5 kg (62.7 lbs) (clamps incl.) 2656 x 320 x 190 mm (99.88 x 12.6 x 7.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 iRCU out in 698–894 –45° iRCU 698–894 +45° 7-16 long neck7-16 8pin male 8pin female in out 1710 –2170 1710 –2170 –45° +45° 7-16 long neck7-16 8pin female 8pin male For more information about additional mounting accessories please refer to page 191 75 Multi-band Panel 698 – 894 1710 – 2170 X X Half-power Beam Width 85° 85° iRCU iRCU 0°–16° 0°–10° Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XXPol Panel iRCU 698–894/1710–2170 85°/85° 14/16.5dBi 0°–16°/0°–10°T 80010721V01 Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio 698 – 894 698 – 806 MHz 824 – 894 MHz +45°, –45° 11.35 dBd / 13.5 dBi +45°, –45° 11.85 dBd / 14 dBi 1710 – 2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° +45°, –45° 16.5 dBi 16.5 dBi 85° Copolar: > 25 dB Average: 32 dB 85° Copolar: > 25 dB Average: 28 dB 88° Copolar: > 25 dB Average: 26 dB Cross polar ratio Maindirection 0° Typically: > 20 dB Typically: > 22 dB Sector ±60° > 10 dB, Avg. 14 dB > 10 dB, Avg. 15 dB Tracking, Avg. 1.5 dB Squint ±4.5° Vertical Pattern: Half-power beam width 16.5° 15.1° Electrical tilt 0°– 16°, continuously adjustable Min. sidelobe suppression for 0° ... 8° ... 16° T 0° ... 8° ... 16° T first sidelobe above main beam: 18 ... 16 ... 18 dB 18 ... 18 ... 17 dB Average: 20 ... 19 ... 19 dB 22 ... 20 ... 20 dB Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply s clamped d lu c in 85° Copolar: > 25 dB Average: 27 dB Typically: > 15 dB Typically: > 15 dB > 10 dB, Avg. 12 dB > 8 dB, Avg. 12 dB 0.5 dB ±4.0° 6.7° 6.7° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 18 ... 18 ... 16 dB 18 ... 18 ... 18 dB 22 ... 22 ... 19 dB 22 ... 22 ... 22 dB 50 Ω < 1.5 Intrasystem: > 30 dB, Intersystem: > 35 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 2 x 8pin male iRCU out: 2 x 8pin female Bottom Frontal: 670 N (at 150 km/h) 1680 N (at 150 mph) Lateral: 250 N (at 150 km/h) 610 N (at 150 mph) 700 N (at 150 km/h) 1740 N (at 150 mph Rearside: 241 km/h (150 mph) 1394 / 300 / 152 mm (54.9 / 11.8 / 6.0 inches) M (Medium) 21 kg (46.2 lbs) / 23 kg (50.6 lbs) (clamps incl.) 1616 x 322 x 190 mm (63.6 x 12.6 x 7.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 iRCU out in 698–894 –45° iRCU 698–894 +45° 7-16 long neck7-16 8pin male 8pin female 76 in out 1710 –2170 1710 –2170 –45° +45° 7-16 long neck7-16 8pin female 8pin male For more information about additional mounting accessories please refer to page 191 Multi-band Panel 698 – 894 1710 – 2170 X X Half-power Beam Width 85° 85° iRCU iRCU 0°–10° 0°–10° Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XXPol Panel iRCU 698–894/1710–2170 85°/85° 15/17.5dBi 0°–10°/0°–10°T 80010722V01 Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio 698 – 894 698 – 806 MHz 824 – 894 MHz +45°, –45° 12.5 dBd / 14.65 dBi +45°, –45° 13 dBd / 15.15 dBi 1710 – 2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° +45°, –45° 17 dBi 17.5 dBi 85° Copolar: > 28 dB Average: 31 dB 85° Copolar: > 27 dB Average: 29 dB 85° Copolar: > 25 dB Average: 28 dB Cross polar ratio Maindirection 0° Typically: > 22 dB Typically: > 24 dB Sector ±60° > 10 dB, Avg. 16 dB > 10 dB, Avg. 16 dB Tracking, Avg. 0.5 dB Squint ±4.0° Vertical Pattern: Half-power beam width 12.1° 11° Electrical tilt 0°– 10°, continuously adjustable Min. sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T first sidelobe above main beam: 16 ... 16 ... 18 dB 15 ... 18 ... 18 dB Average: 17 ... 19 ... 21 dB 16 ... 19 ... 22 dB Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply s clamped d lu c in 85° Copolar: > 25 dB Average: 28 dB Typically: > 18 dB Typically: > 18 dB > 10 dB, Avg. 12 dB > 8 dB, Avg. 12 dB 0.5 dB ±4.5° 5.5° 5.5° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 16 ... 16 ... 16 dB 16 ... 16 ... 16 dB 18 ... 18 ... 18 dB 17 ... 17 ... 18 dB 50 Ω < 1.5 Intrasystem: > 30 dB, Intersystem: > 35 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 2 x 8pin male iRCU out: 2 x 8pin female Bottom Frontal: 900 N (at 150 km/h) 2260 N (at 150 mph) Lateral: 330 N (at 150 km/h) 830 N (at 150 mph) Rearside: 940 N (at 150 km/h) 2350 N (at 150 mph) 241 km/h (150 mph) 1828 / 300 / 152 mm (71.9 / 11.8 / 6.0 inches) H (Heavy) 26 kg (57.3 lbs) / 28 kg (61.7 lbs) (clamps incl.) 2050 x 322 x 190 mm (80.7 x 12.6 x 7.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 iRCU out in 698–894 –45° iRCU 698–894 +45° 7-16 long neck7-16 8pin male 8pin female in out 1710 –2170 1710 –2170 –45° +45° 7-16 long neck7-16 8pin female 8pin male For more information about additional mounting accessories please refer to page 191 77 Multi-band Panel 698 – 894 1710 – 2170 X X Half-power Beam Width 85° 85° iRCU iRCU 0°–10° 0°–10° Dual Polarization Integrated replaceable Remote Control Unit Adjustable Electrical Downtilt XXPol Panel iRCU 698–894/1710–2170 85°/85° 16/17.5dBi 0°–10°/0°–10°T 80010723V01 Type No. A) Antenna specifications Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio 698 – 894 698 – 806 MHz 824 – 894 MHz +45°, –45° 13.5 dBd / 15.65 dBi +45°, –45° 14 dBd / 16.15 dBi 1710 – 2170 1710 – 1755 MHz 1850 – 1990 MHz 2110 – 2170 MHz +45°, –45° +45°, –45° 17.5 dBi 17.5 dBi 85° Copolar: > 28 dB Average: 31 dB 85° Copolar: > 27 dB Average: 29 dB 85° Copolar: > 25 dB Average: 28 dB Cross polar ratio Maindirection 0° Typically: > 22 dB Typically: > 24 dB Sector ±60° > 10 dB, Avg. 16 dB > 10 dB, Avg. 16 dB Tracking, Avg. 0.5 dB Squint ±4.0° Vertical Pattern: Half-power beam width 9.5° 8.5° Electrical tilt 0°– 10°, continuously adjustable Min. sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T first sidelobe above main beam: 16 ... 16 ... 18 dB 15 ... 18 ... 18 dB Average: 17 ... 19 ... 21 dB 16 ... 19 ... 22 dB Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input Input Connector position Wind load Max. wind velocity Height/width/depth Category of mounting hardware Weight Packing size Scope of supply s clamped d lu c in 85° Copolar: > 25 dB Average: 28 dB Typically: > 18 dB Typically: > 18 dB > 10 dB, Avg. 12 dB > 8 dB, Avg. 12 dB 0.5 dB ±4.5° 5.5° 5.5° 0°– 10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 16 ... 16 ... 16 dB 16 ... 16 ... 16 dB 18 ... 18 ... 18 dB 17 ... 17 ... 18 dB 50 Ω < 1.5 Intrasystem: > 30 dB, Intersystem: > 35 dB < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 300 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) iRCU in: 2 x 8pin male iRCU out: 2 x 8pin female Bottom Frontal: 1210 N (at 150 km/h) 3040 N (at 150 mph) Lateral: 450 N (at 150 km/h) 1130 N (at 150 mph) Rearside: 1270 N (at 150 km/h) 3170 N (at 150 mph 241 km/h (150 mph) 2368 / 300 / 152 mm (93.2 / 11.8 / 6.0 inches) H (Heavy) 31 kg (68.2 lbs) / 33 kg (72.6 lbs) (clamps incl.) 2596 x 322 x 190 mm (102.2 x 12.6 x 7.5 inches) Panel and 2 units of clamps 42 – 115 mm diameter iRCU specifications (86010149) see page 79 iRCU out in 698–894 –45° iRCU 698–894 +45° 7-16 long neck7-16 8pin male 8pin female 78 in out 1710 –2170 1710 –2170 –45° +45° 7-16 long neck7-16 8pin female 8pin male For more information about additional mounting accessories please refer to page 191 Integrable Remote Control Unit (iRCU) Kathrein’s 86010149 integrable Remote Control Unit (iRCU) allow operators to control the electrical tilt of compatible antennas without direct access to the antenna. • Compliant to AISG 1.1 and 3GPP/AISG 2.0 • Field replaceable without dismantling the antenna • Daisy Chain feasibility • Allow control of the antenna either locally through a laptop computer, on site desktop computer, the optional central control unit; remotely via an ethernet network or over the internet Type No. Protocols Logical interface ex factory 1) Input voltage range Power consumption Connectors 2) Hardware interfaces Adjustment time (full range) Adjustment cycles Temperature range Protection class Lightning protection Weight Packing size Dimensions (H x W x D) 86010149 Compliant to AISG 1.1 and 3GPP/AISG 2.0 AISG 2.0/3GPP 10 ... 30 V (pin 1, pin 6) < 1 W (stand by); < 10 W (motor activated) 2 x 8 pin connector according to IEC 60130-9; according to AISG Daisy chain in: male; Daisy chain out: female RS 485A/B (pin 5, pin 3); power supply (pin 1, pin 6); DC return (pin 7); according to AISG / 3GPP 40 sec (typically, depending on antenna type) > 50,000 –40 °C … +60 °C IP 24 AISG interface (each pin); 2.5 kA (10/350µs); 8 kA (8/20µs) 480 g (1.16 lbs), 1.0 G lbs 245 x 93 x 102 mm, (9.6 x 3.6 x 4 inches) 170 x 68.5 x 66 mm, (6.68 x 2.7 x 2.6 inches) 1) The protocol of the logical interface can be switched from 3GPP/AISG 2.0 to AISG 1.1 and vice versa with a vendor specific command. Please note: If the Primary of the RET system doesn’t support the standard of the ‘logical interface ex factory’, the iRCU must be switched to the appropriate standard of the Primary before installation. Please contact Kathrein for further information. 2) he tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). The connector T should be tightened by hand only! Standards EN 60950-1 (Safety) EN 55022 (Emission) EN 55024 (Immunity) ETS 300019-1-4 (Environmental) Certification: CE, FCC15.107 class B Scope of supply: Integrable Remote Control Unit For more information about additional mounting accessories please refer to page 191 79 80 Summary – Directional Antennas XXPol 790...960 / 1710...2690 MHz Dual Polarization +45°/–45° Type XXPol Panel 790–960 1710–2690 XXPol Panel 790–960 1710–2170 790–960 1710–2170 XXPol Panel XXPol Panel XXPol Panel 790–960 1710–2180 790–960 1710–2180 C C C Type No. Height [mm] Connector position Page 65° 60° 8dBi 9dBi 0°T 0°T 80010753 334 bottom 82 65° 60° 65° 60° 12dBi 14dBi 12dBi 14dBi 0°T 0°T 0°T 0°T 742226V01 579 bottom or top 83 742222V01 579 bottom or top 84 65° 65° 65° 65° 14.5dBi 0°–14°T 17.5dBi 0°–8°T 14.5dBi 0°–14°T 17.5dBi 0°–8°T 742264V02 1334 bottom 85 742223V02 1334 bottom 86 XXPol Panel 790–960 1710–2690 65° 65° 15dBi 0°–16°T 17.5dBi 2°–10°T 80010664 1403 bottom 87 XXPol Panel 790–960 1710–2180 790–960 1710–2180 790–960 1710–2180 790–960 1710–2180 790–960 1710–2690 65° 65° 65° 65° 65° 65° 65° 65° 65° 65° 16dBi 18.5dBi 16dBi 18.5dBi 16.5dBi 18.5dBi 16dBi 18.5dBi 16dBi 18.5dBi 742265V02 1933 bottom 88 80010771 1934 rearside 89 80010485V01 2038 bottom 90 742224V02 1933 bottom 91 80010665V01 1997 bottom 92 65° 65° 65° 65° 65° 65° 65° 65° 65° 65° 17dBi 0°–7°T 18.5dBi 0°–6°T 17dBi 0°–8°T 18.5dBi 0°–6°T 17dBi 0°–10°T 18.5dBi 0°–6°T 17.5dBi 4°–12°T 18.5dBi 4°–14°T 17dBi 0°–7°T 18.5dBi 0°–6°T 742266V02 2533 bottom 93 80010772 2399 rearside 94 80010666 2622 bottom 95 80010486V01 2516 bottom 96 742225V02 2533 bottom 97 XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel XXPol Panel 790–960 1710–2180 790–960 1710–2180 790–960 1710–2690 790–960 1710–2180 790–960 1710–2180 C C 0°–10°T 0°–6°T 0°–10°T 0°–6°T 2°–14°T 4°–14°T 0°–10°T 0°–6°T 0°–10°T 2°–8°T XXPol Panel 790–960 1710–2180 90° 90° 13.5dBi 0°–13°T 16.5dBi 0°–10°T 80010121V01 1384 bottom 98 XXPol Panel 790–960 1710–2180 90° 90° 15dBi 0°–10°T 18dBi 0°–6°T 80010122V01 1917 bottom 99 XXPol Panel 790–960 1710–2180 90° 90° 80010123V03 2635 bottom 100 C = integrated Combiner 16.5dBi 18dBi 0°–7°T 0°–6°T New or changed product ying deploennas, n e h t W ng ted an er usi the lisso consid ombiners l dC ea pleas l Dual-ban 0 and 231) 3 a i 2 c s e e p s ag (see p 81 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2690 X X 65° 65° XXPol Panel 790–960/1710–2690 C 65°/65° 8/9dBi Frequency range 790 – 862 MHz Polarization +45°, –45° Average gain (dBi) 2 x 7.8 dBi Horizontal Pattern: Half-power beam width Front-to-back ratio [dB] Copolar: > 25 Cross polar ratio 0° Typically: 15 dB Maindirection Sector ±60° Typically: 8 dB Vertical Pattern: Half-power beam width Impedance VSWR Isolation: Intrasystem Intermodulation IM3 Max. power Max. power per combined input Input Connector position Wind load (at 150 km/h) Max. wind velocity Height/width/depth Category of mounting hardware Weight Scope of supply 790 – 960 824 – 894 MHz +45°, –45° 2 x 8.0 dBi 67° Copolar: > 25 1710 – 2690 880 – 960 MHz 1710 – 1990 MHz 1920 – 2200 MHz 2200 – 2490 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 2 x 8.5 dBi 2 x 7.8 dBi 2 x 8.9 dBi 2 x 8.7 dBi 2 x 8.2 dBi 65° Copolar: > 25 Copolar: > 25 Typically: 18 dB Typically: 20 dB Typically: 8 dB Typically: 8 dB 75° 50 Ω < 1.5 > 30 dB 55° Copolar: > 25 Typically: 25 dB Typically: 25 dB Typically: 10 dB Typically: 10 dB 65° 60° 60° Copolar: > 25 62° Copolar: > 25 Typically: 25 dB Typically: 10 dB Typically: 25 dB Typically: 10 dB 60° 65° > 30 dB > 27 dB < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 100 W (at 50 °C ambient temperature) 350 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom Frontal / lateral / rearside: 110 / 55 / 145 N 200 km/h 334 / 260 / 145 mm L (Light) 2.8 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter 790–960 –45° 1710 –2690 –45° 82 s clamped d lu c in 80010753 Type No. 790 –960 +45° > 25 dB 1710–2690 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2170 X X 65° 65° XXPol Panel 790–960/1710–2170 65°/60° 12/14dBi 0°/0°T s clamped d lu c in 742226V01 Type No. 790 – 960 1710 – 2170 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain 2 x 11.1 dBi 2 x 11.4 dBi 2 x 11.8 dBi 2 x 12.8 dBi 2 x 13.3 dBi 2 x 13.6 dBi Horizontal Pattern: Half-power beam width 68° 67° 65° 66° 60° 60° Front-to-back ratio [dB] Copolar: > 23 Copolar: > 23 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 [dB] Total power: > 20 Total power: > 20 Total power: > 22 Total power: > 22 Total power: > 22 Total power: > 22 (180°±30°) Cross polar ratio Typically: 25 dB Typically: 25 dB Typically: 16 dB Typically: 18 dB Typically: 20 dB Maindirection 0° Typically: 25 dB ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector Tracking, Avg. 1.0 dB 0.5 dB Squint ±3.0° ±1.5° Vertical Pattern: Half-power beam width 34° 33° 30° 20° 18° 17.5° Electrical tilt 0°, fixed 0°, fixed VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 > 30 dB > 42 dB (790–960 // 1710–2170 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 200 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 200 / 90 / 250 N 579 / 262 / 139 mm M (Medium) 7.5 kg / 9.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2170 –45° 790–960 –45° 790–960 +45° 1710–2170 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 83 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2170 X X 65° 60° XXPol Panel 790–960/1710–2170 C 65°/60° 12/14dBi 0°/0°T 742222V01 Type No. s clamped d lu c in 790 – 960 1710 – 2170 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain 2 x 11.1 dBi 2 x 11.4 dBi 2 x 11.8 dBi 2 x 12.5 dBi 2 x 13.3 dBi 2 x 13.6 dBi Horizontal Pattern: Half-power beam width 68° 67° 65° 66° 60° 60° Front-to-back ratio [dB] Copolar: > 23 Copolar: > 23 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 [dB] Total power: > 20 Total power: > 20 Total power: > 22 Total power: > 22 Total power: > 22 Total power: > 22 (180°±30°) Cross polar ratio Typically: 25 dB Typically: 25 dB Typically: 18 dB Typically: 18 dB Typically: 20 dB Maindirection 0° Typically: 25 dB ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector Vertical Pattern: Half-power beam width 34° 33° 30° 20° 18° 17.5° Electrical tilt 0°, fixed 0°, fixed VSWR Isolation: Intrasystem Intermodulation IM3 Max. power Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 2 x 7-16 female Bottom or top Frontal / lateral / rearside: 200 / 90 / 250 N 579 / 262 / 139 mm M (Medium) 7.5 kg / 9.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter Integrated combiner The insertion loss is included in the given antenna gain values. 1710–2170 –45° 84 < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 790 –960 –45° 1710–2170 +45° 790 –960 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/65° 14.5/17.5dBi 0°–14°/0°–8°T s clamped d lu c in 742264V02 Type No. 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 14.1 ... 14.1 ... 13.7 14.3 ... 14.2 ... 13.8 14.5 ... 14.4 ... 13.9 17.1 ... 17.3 ... 17.1 17.2 ... 17.4 ... 17.1 17.3 ... 17.5 ... 17.2 Tilt 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° Horizontal Pattern: Half-power beam width 68° 67° 65° 65° 62° 61° Front-to-back ratio, > 30 dB > 30 dB > 30 dB > 32 dB > 32 dB > 32 dB copalar Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Maindirection 0° > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Tracking, Avg. 1.0 dB 0.5 dB Squint ±2.0° ±3.0° Vertical Pattern: Half-power beam width 16.5° 16° 15.3° 7.4° 7.1° 6.7° Electrical tilt 0°–14°, continuously adjustable 0°–8°, continuously adjustable Sidelobe supression for 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T first sidelobe above main 17 ... 16 ... 15 dB 19 ... 18 ... 18 dB 17 ... 18 ... 17 dB 17 ... 17 ... 16 dB 15 ... 15 ... 15 dB 16 ... 16 ... 15 dB beam avg. VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 > 30 dB > 45 dB, Typ. > 50 dB (790–960 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 560 / 260 / 600 N 1334 / 261 / 146 mm M (Medium) 16 kg / 18 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790 – 960 –45° 790 – 960 +45° 1710 – 2180 –45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 85 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 C 65°/65° 14.5/17.5dBi 0°–14°/0°–8°T 742223V02 Type No. s clamped d lu c in 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 14.1 ... 14.1 ... 13.7 14.5 ... 14.4 ... 13.9 17.1 ... 17.3 ... 17.1 17.2 ... 17.4 ... 17.1 17.3 ... 17.5 ... 17.2 Tilt 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° Horizontal Pattern: Half-power beam width 68° 65° 65° 62° 61° Front-to-back ratio, copalar > 30 dB > 30 dB > 32 dB > 32 dB > 32 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection > 25 dB > 25 dB 0° > 25 dB > 25 dB > 25 dB ±60° > 10 dB > 10 dB Sector > 10 dB > 10 dB > 10 dB Tracking, Avg. 1.0 dB 0.5 dB Squint ±2.0° ±3.0° Vertical Pattern: Half-power beam width 16.5° 15.3° 7.4° 7.1° 6.7° Electrical tilt 0°–14°, continuously adjustable 0°–8°, continuously adjustable Sidelobe supression for first 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T sidelobe above main beam avg. 17 ... 16 ... 15 dB 17 ... 18 ... 17 dB 17 ... 17 ... 16 dB 15 ... 15 ... 15 dB 16 ... 16 ... 15 dB VSWR Isolation: Intrasystem Intermodulation IM3 Max. power per input Total power per combined input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 250 W* 200 W* 450 W* 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 560 / 260 / 600 N 1334 / 261 / 146 mm M (Medium) 15.5 kg / 17.5 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter Integrated combiner The insertion loss is included in the given antenna gain values. * (at 50 °C ambient temperature) 1710–2180 –45° 86 < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 790 –960 –45° 1710–2180 +45° 790 –960 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2690 X X 65° 65° XXPol Panel 790–960/1710–2690 65°/65° 15/17.5dBi 0°–16°/2°–10°T 80010664 Type No. s clamped d lu c in 790 – 960 1710 – 2690 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2490 – 2690 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average gain (dBi) 14.5 ... 14.4 ... 14.2 14.6 ... 14.5 ... 14.3 14.8 ... 14.6 ... 14.4 17.2 ... 17.3 ... 16.8 17.4 ... 17.4 ... 16.9 17.6 ... 17.7 ... 17.0 17.2 ... 17.3 ... 16.7 Tilt 0° ... 8° ... 16° 0° ... 8° ... 16° 0° ... 8° ... 16° 2° ... 5° ... 10° 2° ... 5° ... 10° 2° ... 5° ... 10° 2° ... 5° ... 10° Horizontal Pattern: Half-power beam width 69° 68° 67° 63° 64° 66° 65° Front-to-back ratio, copolar (180°±30°) > 25 dB > 25 dB > 25 dB > 25 dB > 28 dB > 29 dB > 25 dB Cross polar ratio Maindirection 0° Typically: 25 dB Typically: 25 dB Typically: 25 dB Typically: 18 dB > 20 dB 20 dB 23 dB Sector ±60° > 10 dB > 9 dB > 8 dB > 9 dB > 10 dB > 10 dB > 8 dB Vertical Pattern: Half-power beam width 16.5° 16.0° 15.5° 6.2° 5.8° 5.2° 4.8° Electrical tilt 0°–16°, continuously adjustable 2°–10°, continuously adjustable Sidelobe suppression for first 0° ... 8° ... 16° T 0° ... 8° ... 16° T 0° ... 8° ... 16° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T 16 ... 15 ... 15 dB 16 ... 15 ... 15 dB 15 ... 15 ... 14 dB 14 ... 15 ... 16 dB 14 ... 15 ... 17 dB 15 ... 16 ... 17 dB 15 ... 17 ... 18 dB sidelobe above main beam Impedance VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 50 Ω < 1.5 > 30 dB > 28 dB > 30 dB (790–960 // 1710–2690) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 690 / 270 / 720 N 1403 / 300 / 152 mm M (Medium) 18 kg / 20 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790–960 –45° 790–960 +45° 1710–2690 –45° 1710–2690 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 > 30 dB 87 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/65° 16/18.5dBi 0°–10°/0°–6°T s clamped d lu c in 742265V02 Type No. 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 15.6 ... 15.5 ... 15.3 15.9 ... 15.8 ... 15.5 16.1 ... 16.0 ... 15.6 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ... 18.7 ... 18.3 Tilt 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 67° 65° 65° 65° 61° Front-to-back ratio, > 27 dB > 28 dB > 28 dB > 30 dB > 30 dB > 30 dB copalar Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Maindirection > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB 0° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector ±60° Tracking, Avg. 1.5 dB 0.5 dB Squint ±2.5° ±2.5° Vertical Pattern: Half-power beam width 10.9° 10.6° 10° 5.0° 4.8° 4.6° Electrical tilt 0.5°–9.5°, continuously adjustable 0°–6°, continuously adjustable Sidelobe supression for first 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 15 ... 16 ... 17 dB ≥ 15 ... 17 ... 19 dB ≥ 15 ... 18 ... 19 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 88 < 1.5 > 30 dB < 1.5 > 30 dB > 45 dB, Typ. > 50 dB (790–960 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 850 / 380 / 910 N 1933 / 261 / 146 mm M (Medium) 20 kg / 22 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 790 – 960 –45° 790 – 960 +45° 1710 – 2180 –45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/65° 16/18.5dBi 0°–10°/0°–6°T 80010771 Type No. s clamped d lu c in 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 15.4 ... 15.5 ... 15.2 15.5 ... 15.8 ... 15.3 15.8 ... 16.0 ... 15.4 18.3 ... 18.5 ... 18.2 18.5 ... 18.7 ... 18.3 18.2 ... 18.6 ... 18.2 Tilt 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 69° 67° 65° 65° 62° 62° Front-to-back ratio, > 27 dB > 28 dB > 28 dB > 30 dB > 30 dB > 30 dB copalar Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Maindirection > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB 0° ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector Tracking, Avg. 1.5 dB 0.5 dB Squint ±3.0° ±2.5° Vertical Pattern: Half-power beam width 11° 10.7° 10° 5.0° 4.8° 4.6° Electrical tilt 0°–10°, continuously adjustable 0°–6°, continuously adjustable Sidelobe suppression for first 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 17 ... 17 ... 17 dB ≥ 17 ... 17 ... 18 dB ≥ 17 ... 17 ... 16 dB ≥ 17 ... 16 ... 15 dB ≥ 17 ... 16 ... 15 dB ≥ 17 ... 16 ... 15 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Max. power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 > 30 dB < 1.5 < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB (790–960 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female Rearside 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 680 / 380 / 890 N 1934 / 260 / 140 mm M (Medium) 15 kg / 17 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790 – 960 –45° 790 – 960 +45° 1710 – 2180 –45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 89 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/65° 16.5/18.5dBi 2°–14°/4°–14°T 80010485V01 Type No. s clamped d lu c in 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average gain (dBi) 16.2 ... 16.0 ... 15.7 16.3 ... 16.1 ... 15.8 16.4 ... 16.2 ... 15.8 18.0 ... 18.2 ... 17.7 18.4 ... 18.5 ... 17.8 18.7 ... 18.6 ... 18.0 Tilt 2° ... 8° ... 14° 2° ... 8° ... 14° 2° ... 8° ... 14° 4° ... 9° ... 14° 4° ... 9° ... 14° 4° ... 9° ... 14° Horizontal Pattern: Half-power beam width 68° 67° 65° 66° 64° 60° Front-to-back ratio (180°±30°) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Typically: Cross polar ratio Typically: Typically: Typically: Typically: Typically: 0° Maindirection > 25 dB > 25 dB > 25 dB > 20 dB > 20 dB > 21 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Vertical Pattern: Half-power beam width 10° 9.7° 9.3° 5° 4.7° 4.5° Electrical tilt 2°–14°, continuously adjustable 4°–14°, continuously adjustable Sidelobe supression for first 2° ... 8° ... 14° T 2° ... 8° ... 14° T 2° ... 8° ... 14° T 4° ... 9° ... 14° T 4° ... 9° ... 14° T 4° ... 9° ... 14° T sidelobe above main beam 17 ... 17 ... 15 dB 17 ... 17 ... 16 dB 17 ... 17 ... 16 dB 20 ... 18 ... 15 dB 19 ... 18 ... 15 dB 18 ... 17 ... 15 dB Impedance VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 90 50 Ω < 1.5 > 30 dB > 35 dB (790–960 // 1710–2180 MHz) < –153 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 800 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 750 / 380 / 900 N 2038 / 262 / 139 mm M (Medium) 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 1710–2180 –45° 790–960 –45° 790–960 +45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 C 65°/65° 16/18.5dBi 0°–10°/0°–6°T 742224V02 Type No. s clamped d lu c in 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 15.6 ... 15.5 ... 15.3 16.1 ... 16.0 ... 15.6 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ... 18.7 ... 18.3 Tilt 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 65° 65° 65° 61° Front-to-back ratio, copolar > 27 dB > 28 dB > 30 dB > 30 dB > 30 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection > 25 dB > 25 dB 0° > 25 dB > 25 dB > 25 dB ±60° > 10 dB > 10 dB Sector > 10 dB > 10 dB > 10 dB Tracking, Avg. 1.5 dB 0.5 dB Squint ±2.5° ±2.5° Vertical Pattern: Half-power beam width 10.9° 10° 5.0° 4.8° 4.6° Electrical tilt 0.5°–9.5°, continuously adjustable 0°–6°, continuously adjustable Sidelobe supression for first 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 15 ... 16 ... 17 dB ≥ 15 ... 18 ... 19 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR Isolation: Intrasystem Intermodulation IM3 Max. power per input Total power per combined input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 250 W* < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 200 W* 450 W* 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 850 / 380 / 910 N 1933 / 261 / 146 mm M (Medium) 20 kg / 22 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter Integrated combiner The insertion loss is included in the given antenna gain values. * (at 50 °C ambient temperature) 1710–2180 –45° 790 –960 –45° 1710–2180 +45° 790 –960 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 191 91 Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2690 X X 65° 65° XXPol Panel 790–960/1710–2690 65°/65° 16/18.5dBi 0°–10°/2°–8°T 80010665V01 Type No. 790 – 960 1710 – 2690 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2300 – 2400 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.1 ... 16.1 ... 15.6 16.1 ... 16.2 ... 15.8 16.1 ... 16.2 ... 15.8 18.2 ... 18.3 ... 18.0 18.4 ... 18.4 ... 18.1 18.7 ... 18.7 ... 18.2 18.9 ... 18.7 ... 18.0 18.2 ... 18.7 ... 18.4 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 2° ... 5° ... 8° 2° ... 5° ... 8° 2° ... 5° ... 8° 2° ... 5° ... 8° 2° ... 5° ... 8° Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width 68° 67° 65° 63° 63° 62° 61° 63° Front-to-back ratio, copolar (180°±30°) > 27 dB > 27 dB > 27 dB > 25 dB > 26 dB > 26 dB > 25 dB > 26 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Typically: Typically: Maindirection > 28 dB > 27 dB 0° > 23 dB > 18 dB > 22 dB > 23 dB > 20 dB > 25 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB Vertical Pattern: Half-power beam width 10.0° 9.8° 9.5° 5.0° 4.8° 4.4° 3.9° 3.5° Electrical tilt 0°–10°, continuously adjustable 2°–8°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 2° ... 5° ... 8° T 2° ... 5° ... 8° T 2° ... 5° ... 8° T 2° ... 5° ... 8° T 2° ... 5° ... 8° T Sidelobe suppression – for first sidelobe above main beam 19 ... 15 ... 17 dB 19 ... 17 ... 18 dB 18 ... 16 ... 17 dB 17 ... 18 ... 19 dB 18 ... 18 ... 19 dB 18 ... 18 ... 19 dB 18 ... 18 ... 18 dB 17 ... 18 ... 19 dB – within 0°–20° sector above horizon 18 ... 15 ... 16 dB 18 ... 16 ... 15 dB 18 ... 16 ... 14 dB 16 ... 16 ... 17 dB 17 ... 16 ... 18 dB 17 ... 17 ... 16 dB 18 ... 18 ... 15 dB 16 ... 18 ... 14 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 92 < 1.5 > 30 dB > 28 dB > 30 dB (790–960 // 1710–2690 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 200 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 400 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 990 / 380 / 1030 N 1997 / 300 / 152 mm M (Medium) 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790–960 –45° 790–960 +45° 1710–2690 –45° 1710–2690 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/65° 17/18.5dBi 0°–7°/0°–6°T s clamped d lu c in 742266V02 Type No. 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 16.6 ... 16.6 ... 16.5 17.0 ... 16.9 ... 16.7 17.0 ... 17.1 ... 16.9 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ... 18.7 ... 18.3 Tilt 0° ... 3° ... 7° 0° ... 3° ... 7° 0° ... 3° ... 7° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 67° 65° 65° 65° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Maindirection 0° > 30 dB > 30 dB > 30 dB > 25 dB > 25 dB > 25 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector ±60° Tracking, Avg. 1.0 dB 0.5 dB Squint ±2.5° ±2.5° Vertical Pattern: Half-power beam width 8.0° 7.7° 7.2° 5.0° 4.8° 4.6° Electrical tilt 0°–7°, continuously adjustable 0°–6°, continuously adjustable Sidelobe supression for first 0° ... 3° ... 7° T 0° ... 3° ... 7° T 0° ... 3° ... 7° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 17 ... 17 ... 15 dB ≥ 17 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 > 30 dB > 45 dB, Typ. > 50 dB (790–960 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1160 / 500 / 1210 N 2533 / 261 / 146 mm H (Heavy) 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2180 –45° 790–960 –45° 790–960 +45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 93 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/65° 17/18.5dBi 0°–8°/0°–6°T s clamped d lu c in 80010772 Type No. 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 16.6 ... 16.8 ... 16.6 16.8 ... 17.0 ... 16.7 16.8 ... 17.0 ... 16.7 18.4 ... 18.5 ... 18.0 18.5 ... 18.7 ... 18.1 18.4 ... 18.6 ... 18.0 Tilt 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 67° 65° 65° 62° 62° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Maindirection 0° > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector ±60° Tracking, Avg. 1.5 dB 0.5 dB Squint ±3.0° ±2.5° Vertical Pattern: Half-power beam width 8.0° 7.9° 7.6° 5.0° 4.8° 4.6° Electrical tilt 0°–8°, continuously adjustable 0°–6°, continuously adjustable Sidelobe suppression for first 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 16 ... 17 ... 16 dB ≥ 15 ... 17 ... 18 dB ≥ 15 ... 17 ... 18 dB ≥ 17 ... 16 ... 15 dB ≥ 17 ... 16 ... 15 dB ≥ 17 ... 16 ... 15 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Max. power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 94 < 1.5 > 30 dB < 1.5 > 30 dB > 30 dB (790–960 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female Rearside 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 840 / 480 / 1160 N 2399 / 260 / 140 mm H (Heavy) 17 kg / 19 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790 – 960 –45° 790 – 960 +45° 1710 – 2180 –45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2690 X X 65° 65° XXPol Panel 790–960/1710–2690 65°/65° 17/18.5dBi 0°–10°/0°–6°T 80010666 Type No. s clamped d lu c in 790 – 960 1710 – 2690 790 – 866 MHz 824 – 896 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.8 ... 16.7 ... 16.5 17.0 ... 17.0 ... 16.8 17.1 ... 17.2 ... 17.0 18.5 ... 18.4 ... 18.1 18.5 ... 18.4 ... 18.1 18.8 ... 18.7 ... 18.2 18.2 ... 18.3 ... 18.0 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width 68° 67° 65° 62° 63° 62° 63° Front-to-back ratio, copalar (180°±30°) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Typically: Maindirection > 23 dB > 22 dB 0° > 24 dB > 18 dB > 22 dB > 23 dB > 25 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector ±60° > 10 dB > 10 dB Vertical Pattern: Half-power beam width 7.5° 7.4° 7.1° 4.5° 4.4° 4.1° 3.5° Electrical tilt 0.5°–9.5°, continuously adjustable 0°–6°, continuously adjustable Min. sidelobe supression for 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam 18 ... 16 ... 14 dB 18 ... 17 ... 15 dB 18 ... 18 ... 16 dB 17 ... 16 ... 16 dB 18 ... 18 ... 17 dB 18 ... 17 ... 17 dB 18 ... 18 ... 17 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB > 28 dB > 30 dB (790–960 // 1710–2690 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 200 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 400 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1270 /490 / 1320 N 2622 / 300 / 152 mm H (Heavy) 29 kg / 31 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790–960 –45° 790–960 +45° 1710–2690 –45° 1710–2690 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 95 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 65°/65° 17.5/18.5dBi 4°–12°/4°–14°T 790 – 960 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Average gain (dBi) 16.8 ... 16.7 ... 16.6 17.0 ... 16.8 ... 16.8 17.2 ... 17.0 ... 16.8 Tilt 4° ... 8° ... 12° 4° ... 8° ... 12° 4° ... 8° ... 12° Horizontal Pattern: Half-power beam width 68° 67° 66° Front-to-back ratio > 25 dB > 25 dB > 25 dB (180°±30°) Cross polar ratio Typically: Typically: Typically: Maindirection 0° > 23 dB > 24 dB > 25 dB Sector ±60° > 10 dB > 10 dB > 10 dB Vertical Pattern: Half-power beam width 7.5° 7.4° 7.2° Electrical tilt 4°–12°, continuously adjustable 4° ... 8° ... 12° T 4° ... 8° ... 12° T 4° ... 8° ... 12° T Sidelobe supression – for first sidelobe above main beam 18 ... 17 ... 16 dB 19 ... 18 ... 18 dB 19 ... 18 ... 18 dB – within 0°–20° sector above horizon 15 ... 15 ... 14 dB 16 ... 15 ... 14 dB 16 ... 15 ... 14 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 96 s clamped d lu c in 80010486V01 Type No. 1710 – 2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° 17.8 ... 18.1 ... 17.5 18.3 ... 18.3 ... 17.8 18.7 ... 18.7 ... 18.0 4° ... 9° ... 14° 4° ... 9° ... 14° 4° ... 9° ... 14° 66° > 25 dB 64° > 25 dB 61° > 25 dB Typically: > 18 dB > 10 dB Typically: > 18 dB > 10 dB Typically: > 20 dB > 10 dB 5° 4.8° 4.6° 4°–14°, continuously adjustable 4° ... 9° ... 14° T 4° ... 9° ... 14° T 4° ... 9° ... 14° T 20 ... 18 ... 16 dB 19 ... 19 ... 16 dB 18 ... 18 ... 18 dB 17 ... 17 ... 15 dB 17 ... 17 ... 15 dB 17 ... 17 ... 15 dB < 1.5 > 30 dB > 45 dB (790–960 // 1710–2180 MHz) < –153 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 800 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 920 / 460 / 1150 N 2516 / 262 / 139 mm H (Heavy) 28 kg / 30 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2180 –45° 790–960 –45° 790–960 +45° 1710–2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 65° 65° XXPol Panel 790–960/1710–2180 C 65°/65° 17/18.5dBi 0°–7°/0°–6°T s clamped d lu c in 742225V02 Type No. 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 16.6 ... 16.6 ... 16.5 17.0 ... 17.1 ... 16.9 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ... 18.7 ... 18.3 Tilt 0° ... 3° ... 7° 0° ... 3° ... 7° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 65° 65° 65° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection > 30 dB > 30 dB 0° > 25 dB > 25 dB > 25 dB ±60° > 10 dB > 10 dB Sector > 10 dB > 10 dB > 10 dB Tracking, Avg. 1.0 dB 0.5 dB Squint ±2.5° ±2.5° Vertical Pattern: Half-power beam width 7.7° 7.2° 5.0° 4.8° 4.6° Electrical tilt 0°–7°, continuously adjustable 0°–6°, continuously adjustable Sidelobe supression for first 0° ... 4° ... 7° T 0° ... 4° ... 7° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T sidelobe above main beam avg. ≥ 17 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR Isolation: Intrasystem Intermodulation IM3 Max. power per input Total power per combined input 250 W* Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 450 W* 200 W* 2 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1160 / 500 / 1210 N 2533 / 261 / 146 mm H (Heavy) 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Integrated combiner The insertion loss is included in the given antenna gain values. * (at 50 °C ambient temperature) 1710–2180 –45° 790 –960 –45° 1710–2180 +45° 790 –960 +45° C C 7-16 7-16 For more information about additional mounting accessories please refer to page 191 97 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 90° 90° XXPol Panel 790–960/1710–2180 90°/90° 13.5/16.5dBi 0°–13°/0°–10°T 80010121V01 Type No. s clamped d lu c in 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average gain (dBi) 13.4 ... 13.4 ... 13.1 13.6 ... 13.6 ... 13.4 13.9 ... 13.8 ... 13.5 16.4 ... 16.4 ... 16.2 16.4 ... 16.5 ... 16.0 16.4 ... 15.9 ... 15.3 Tilt 0.5° ... 6° ... 12.5° 0.5° ... 6° ... 12.5° 0.5° ... 6° ... 12.5° 0.5° ... 5° ... 10° 0.5° ... 5° ... 10° 0.5° ... 5° ... 10° Horizontal Pattern: Half-power beam width 88° 86° 88° 82° 85° 90° Front-to-back ratio, > 23 dB > 23 dB > 23 dB > 23 dB > 23 dB > 23 dB copolar Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Maindirection > 17 dB > 18 dB > 20 dB > 17 dB > 16 dB > 15 dB 0° > 10 dB > 10 dB > 13 dB > 10 dB > 12 dB > 10 dB Sector ±60° avg. 16 dB avg. 16 dB avg. 19 dB avg. 17 dB avg. 19 dB avg. 19 dB ±60° Vertical Pattern: Half-power beam width 15.0° 14.5° 14.0° 7.0° 6.6° 6.4° Electrical tilt 0.5°–12.5°, continuously adjustable 0.5°–10°, continuously adjustable Min. sidelobe supression for 0.5° ... 6° ... 12.5° T 0.5° ... 6° ... 12.5° T 0.5° ... 6° ... 12.5° T 0.5° ... 5° ... 10° T 0.5° ... 5° ... 10° T 0.5° ... 5° ... 10° T first sidelobe above main beam: 16 ... 14 ... 14 dB 16 ... 15 ... 14 dB 18 ... 16 ... 16 dB 17 ... 17 ... 16 dB 17 ... 18 ... 16 dB 18 ... 16 ... 16 dB average: 20 ... 19 ... 16 dB 20 ... 18 ... 17 dB 22 ... 20 ... 20 dB 20 ... 20 ... 18 dB 21 ... 22 ... 17 dB 20 ... 20 ... 16 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 98 < 1.5 > 30 dB > 42 dB (790–960 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 420 / 260 / 620 N 1384 / 262 / 149 mm M (Medium) 21 kg / 23 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790–960 –45° 790–960 +45° 1710 – 2180 –45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 90° 90° XXPol Panel 790–960/1710–2180 90°/90° 15/18dBi 0°–10°/0°–6°T 80010122V01 Type No. s clamped d lu c in 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 896 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average gain (dBi) 14.8 ... 14.8 ... 14.8 14.8 ... 15.0 ... 14.8 14.9 ... 15.1 ... 14.9 17.7 ... 17.8 ... 17.7 17.7 ... 18.0 ... 17.6 17.6 ... 17.8 ... 17.4 Tilt 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 88° 87° 88° 82° 85° 90° Front-to-back ratio (180°±30°) > 23 dB > 23 dB > 23 dB > 23 dB > 23 dB > 23 dB Typically: Cross polar ratio Typically: Typically: Typically: Typically: Typically: 0° > 20 dB > 17 dB > 16 dB > 15 dB Maindirection > 18 dB > 18 dB Sector ±60° > 10 dB > 10 dB > 13 dB > 10 dB > 12 dB > 10 dB ±60° avg. 16 dB avg. 16 dB avg. 19 dB avg. 17 dB avg. 19 dB avg. 19 dB Vertical Pattern: Half-power beam width 11.0° 10.9° 10.5° 5.5° 5.2° 5.0° Electrical tilt 0°–10°, continuously adjustable 0°–6°, continuously adjustable Min. sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam 18 ... 16 ... 14 dB 16 ... 16 ... 15 dB 16 ... 16 ... 15 dB 18 ... 18 ... 16 dB 18 ... 18 ... 16 dB 18 ... 16 ... 16 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB > 42 dB (790–960 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 580 / 360 / 870 N 1917 / 262 / 149 mm M (Medium) 27 kg / 29 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790–960 –45° 790–960 +45° 1710 – 2180 –45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 99 Dual-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2180 X X 90° 90° XXPol Panel 790–960/1710–2180 90°/90° 16.5/18dBi 0°–7°/0°–6°T 80010123V03 Type No. s clamped d lu c in 790 – 960 1710 – 2180 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average gain (dBi) 16.1 ... 16.2 ... 16.1 16.3 ... 16.4 ... 16.3 16.5 ... 16.6 ... 16.5 17.8 ... 17.7 ... 17.4 18.0 ... 17.9 ... 17.4 17.9 ... 17.8 ... 17.3 Tilt 0.5° ... 4° ... 7° 0.5° ... 4° ... 7° 0.5° ... 4° ... 7° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 86° 86° 86° 84° 85° 88° Front-to-back ratio, copolar > 25 dB > 25 dB > 25 dB > 23 dB > 23 dB > 23 dB Typically: Cross polar ratio Typically: Typically: Typically: Typically: Typically: > 18 dB > 20 dB > 16 dB > 16 dB > 15 dB Maindirection 0° > 18 dB > 10 dB > 10 dB > 13 dB > 10 dB > 12 dB > 10 dB Sector ±60° avg. 16 dB avg. 16 dB avg. 19 dB avg. 16 dB avg. 17 dB avg. 18 dB ±60° Tracking, Avg. 0.5 dB 0.5 dB Squint ±3.0° ±3.0° Vertical Pattern: Half-power beam width 7.3° 7.2° 6.9° 4.8° 4.5° 4.2° Electrical tilt 0.5°–7°, continuously adjustable 0°–6°, continuously adjustable Min. sidelobe supression for 0.5° ... 4° ... 7° T 0.5° ... 4° ... 7° T 0.5° ... 4° ... 7° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam 15 ... 14 ... 14 dB 15 ... 14 ... 14 dB 15 ... 14 ... 15 dB 18 ... 17 ... 16 dB 18 ... 17 ... 17 dB 18 ... 16 ... 17 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 100 < 1.5 > 30 dB > 45 dB (790–960 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 4 x 7-16 female (long neck) Bottom 2x, Position bottom, continuously adjustable Frontal / lateral / rearside: 840 / 510 / 1260 N 2635 / 262 / 149 mm H (Heavy) 33 kg / 35 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 790–960 –45° 790–960 +45° 1710 – 2180 –45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Summary – Directional Antennas XXXPol 698...960 / 1710...2690 MHz Dual Polarization +45°/–45° Type XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel XXXPol Panel Type No. Height [mm] Connector position Page 790–862 880–960 1710–2180 790–862 880–960 1710–2180 790–862 880–960 1710–2180 65° 65° 65° 65° 65° 65° 65° 65° 65° 14dBi 14dBi 17dBi 15.5dBi 16dBi 18.5dBi 16.5dBi 17dBi 18.5dBi 0°–14°T 0°–14°T 0°–8°T 0°–10°T 0°–10°T 0°–6°T 0°–7°T 0°–7°T 0°–6°T 80010697 1332 bottom 102 80010698 1932 bottom 103 80010699 2532 bottom 104 790–960 1710–1880 1920–2170 790–960 1710–2180 1710–2180 65° 65° 65° 65° 65° 65° 15dBi 17dBi 17dBi 15dBi 15dBi 15dBi 0°–14°T 0°–8°T 0°–8°T 0°–14°T 0°–14°T 0°–14°T 742270V03 1384 bottom 105 80010290V02 1540 bottom 106 790–960 1710–1880 1920–2170 790–960 1710–2180 1710–2180 65° 65° 65° 65° 65° 65° 16.5dBi 18dBi 18dBi 16.5dBi 16.5dBi 16.5dBi 0°–10°T 0°–6°T 0°–6°T 2°–14°T 0°–14°T 0°–14°T 742271V03 1933 bottom 107 80010291V02 2058 bottom 108 790–960 1710–1880 1920–2170 790–960 1710–2180 1710–2180 65° 65° 65° 65° 65° 65° 17.5dBi 18dBi 18dBi 17.5dBi 17.5dBi 17dBi 0°–7°T 0°–6°T 0°–6°T 2°–10°T 0°–10°T 0°–10°T 742272V03 2533 bottom 109 80010292V03 2598 bottom 110 790–960 1710–2170 2490–2690 790–960 1710–2170 2490–2690 790–960 1710–2170 2490–2690 790–960 1710–2690 1710–2690 65° 65° 65° 65° 65° 65° 65° 65° 65° 65° 65° 65° 15dBi 17dBi 16.5dBi 16dBi 18dBi 18dBi 17dBi 18dBi 18dBi 16dBi 16dBi 16dBi 0°–16°T 2°–10°T 2°–10°T 0°–10°T 2°–8°T 2°–8°T 0°–10°T 0°–6°T 0°–6°T 0°–10°T 2°–12°T 2°–12°T 80010674 1403 bottom 111 80010675V01 1997 bottom 112 80010676 2622 bottom 113 80010691 1997 bottom 114 698–960 1710–2690 1710–2690 65° 65° 65° 17dBi 17dBi 17dBi 1°–10°T 0°–10°T 2°–10°T 80010692V01 2622 bottom 115 New or changed product ying s, deplo a When nd Antenn using a r e b s d i e l s p on biner Tri also cband Com 2) e s a 3 e pl le d2 31 an al Trip speci ee page 2 (s 101 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 1710–2180 X X X 65° 65° 65° XXXPol Panel 790–862/880–960/1710–2180 65°/65°/65° 14/14/17dBi 0°–14°/0°–14°/0°–8°T s clamped includ 80010697 Type No. 790 – 862 880 – 960 1710 – 2180 Frequency range 790 – 862 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 13.9 ... 13.9 ... 13.3 14.2 ... 14.1 ... 13.5 16.7 ... 16.9 ... 16.7 16.9 ... 17.1 ... 16.7 16.9 ... 17.1 ... 16.8 Gain (dBi) 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 4° ... 8° 0° ... 4° ... 8° 0° ... 4° ... 8° Tilt Horizontal Pattern: Half-power beam width 68° 65° 64° 63° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 32 dB > 32 dB > 32 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection > 25 dB > 25 dB > 25 dB > 25 dB 0° > 25 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector ±60° Vertical Pattern: Half-power beam width 16.5° 15.4° 7.4° 7.1° 6.7° Electrical tilt 0°– 14° 0°– 14° 0°– 8° continuously adjustable Sidelobe suppression for 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T 0° ... 4° ... 8° T first sidelobe above main beam: average: ≥ 17 ... 17 ... 15 dB ≥ 17 ... 17 ... 16 dB ≥ 17 ... 16 ... 15 dB ≥ 17 ... 17 ... 16 dB ≥ 17 ... 17 ... 16 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Totel power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 < 1.5 > 30 dB > 30 dB > 38 dB (790...960 // 1710 – 2180 MHz) > 28 dB, Typ. > 30 dB (790 – 862 // 880 – 960MHz) < –150 dBc < –150 dBc < –150 dBc 250 W* 500 W* 250 W* 500 W* 6 x 7-16 female (long neck) Bottom 3 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 670 / 260 / 700 N 1332 / 300 / 152 mm M (Medium) 21 kg / 23 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) 790–862 –45° 102 250 W* 500 W* 790–862 +45° 880–960 –45° 880–960 +45° 7-16 7-16 1710–2180 1710–2180 –45° +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 1710–2180 X X X 65° 65° 65° XXXPol Panel 790–862/880–960/1710–2180 65°/65°/65° 15.5/16/18.5dBi 0°–10°/0°–10°/0°–6°T s clamped includ 80010698 Type No. 790 – 862 880 – 960 1710 – 2180 Frequency range 790 – 862 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Gain (dBi) 15.1 ... 15.4 ... 15.1 15.6 ... 15.9 ... 15.4 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ... 18.7 ... 18.3 Tilt 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Horizontal Pattern: Half-power beam width 68° 65° 65° 65° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Typically: Cross polar ratio Typically: Typically: Typically: Typically: Maindirection 0° > 25 dB > 27 dB > 25 dB > 25 dB > 25 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Tracking, Avg. 1.0 dB 1.0 dB 0.5 dB Squint ±2.5° ±2.5° ±2.5° Vertical Pattern: Half-power beam width 11.5° 10.1° 5.0° 4.8° 4.6° Electrical tilt, 0°– 10° 0°– 10° 0°– 6° continuously adjustable Sidelobe suppression for 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam: average: ≥ 17 ... 17 ... 17 dB ≥ 17 ... 17 ... 16 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Totel power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 < 1.5 > 30 dB > 30 dB > 38 dB (790...960 // 1710 – 2180 MHz) > 28 dB, Typ. > 30 dB (790 – 862 // 880 – 960MHz) < –150 dBc < –150 dBc < –150 dBc 250 W* 500 W* 250 W* 500 W* 250 W* 500 W* 6 x 7-16 female (long neck) Bottom 3 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 850 / 380 / 910 N 1932 / 269 / 154 mm M (Medium) 23 kg / 25 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) 790–862 –45° 880–960 –45° 880–960 +45° 7-16 7-16 790–862 +45° 1710–2180 1710–2180 –45° +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 103 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 862 880 – 960 1710–2180 X X X 65° 65° 65° XXXPol Panel 790–862/880–960/1710–2180 65°/65°/65° 16.5/17/18.5dBi 0°–7°/0°–7°/0°–6°T s clamped includ 80010699 Type No. 790 – 862 880 – 960 1710 – 2180 Frequency range 790 – 862 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.3 ... 16.4 ... 16.2 16.7 ... 16.9 ... 16.6 18.2 ... 18.5 ... 18.3 18.5 ... 18.7 ... 18.3 18.5 ... 18.7 ... 18.3 Gain (dBi) 0° ... 4° ... 7° 0° ... 4° ... 7° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° Tilt Horizontal Pattern: Half-power beam width 68° 65° 65° 65° 61° Front-to-back ratio, copolar > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection > 28 dB > 25 dB > 25 dB > 25 dB 0° > 25 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector ±60° Vertical Pattern: Half-power beam width 8.3° 7.6° 5.0° 4.8° 4.6° Electrical tilt, 0°– 7° 0°– 7° 0°– 6° continuously adjustable Sidelobe suppression for 0° ... 4° ... 7° T 0° ... 4° ... 7° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam: average: ≥ 17 ... 16 ... 16 dB ≥ 18 ... 17 ... 16 dB ≥ 18 ... 17 ... 15 dB ≥ 18 ... 18 ... 16 dB ≥ 18 ... 18 ... 16 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Totel power Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB < 1.5 < 1.5 > 30 dB > 30 dB > 38 dB (790...960 // 1710 – 2180 MHz) > 28 dB, Typ. > 30 dB (790 – 862 // 880 – 960MHz) < –150 dBc < –150 dBc < –150 dBc 250 W* 500 W* 250 W* 500 W* Bottom 3 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1160 / 500 / 1210 N 2532 / 269 / 154 mm H (Heavy) 26 kg / 28 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) 790–862 –45° 104 250 W* 500 W* 790–862 +45° 880–960 –45° 880–960 +45° 7-16 7-16 1710–2180 1710–2180 –45° +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710–1880 1920–2170 X X X 65° 65° 65° XXXPol Panel 790–960/1710–1880/1920–2170 65°/65°/65° 15/17/17dBi 0°–14°/0°–8°/0°–8°T 1710 – 1880 1710 – 1880 MHz +45°, –45° 16.8 ... 16.9 ... 16.6 0° ... 4° ... 8° s clamped includ 1920 – 2170 1920 – 2170 MHz +45°, –45° 16.9 ... 17.0 ... 16.7 0° ... 4° ... 8° 65° > 32 dB Typically: > 25 dB > 10 dB 0.5 dB ±3.0° 61° > 32 dB Typically: > 25 dB > 10 dB 0.5 dB ±3.0° 7.4° 0°– 8° 0° ... 4° ... 8° T 17 ... 17 ... 16 dB 6.7° 0°– 8° 0° ... 4° ... 8° T 16 ... 16 ... 15 dB 742270V03 Type No. 790 – 960 Frequency range 790 – 862 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° Gain (dBi) 14.4 ... 14.3 ... 14.0 14.8 ... 14.7 ... 14.2 Tilt 0° ... 7° ... 14° 0° ... 7° ... 14° Horizontal Pattern: Half-power beam width 68° 65° Front-to-back ratio, copolar > 30 dB > 30 dB Cross polar ratio Typically: Typically: Maindirection > 25 dB > 25 dB 0° ±60° > 10 dB > 10 dB Sector Tracking, Avg. 1.0 dB Squint ±2.0° Vertical Pattern: Half-power beam width 16.5° 15.3° Electrical tilt, contin. adjust. 0°– 14° Sidelobe suppression for first 0° ... 7° ... 14° T 0° ... 7° ... 14° T sidelobe above main beam avg. 17 ... 16 ... 15 dB 17 ... 18 ... 17 dB VSWR Isolation: Intrasystem Isolation: Intersystem < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB Typically: > 50 dB (790 – 960 // 1710 – 1880 MHz) Typically: > 50 dB (790 – 960 // 1920 – 2170 MHz) > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc < –150 dBc < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 500 W* 1000 W* 200 W* 200 W* 400 W* 400 W* 6 x 7-16 female (long neck) Bottom 3 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 600 / 270 / 640 N 1384 / 261 / 146 mm M (Medium) 19 kg / 21 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter * (at 50 °C ambient temperature) 1710–1880 –45° 790–960 –45° 790–960 +45° 7-16 7-16 1710 –1880 +45° 1920–2170 1920–2170 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 105 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710–2180 1710–2180 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2180/1710–2180 65°/65°/65° 15/15/15dBi 0°–14°/0°–14°/0°–14°T s clamped includ 1710 – 2180 1710 – 2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° 80010290V02 Type No. 790 – 960 Frequency range 790 – 866 MHz 824 – 894 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° +45°, –45° Average gain: (dBi) 14.4 ... 14.3 ... 14.0 14.6 ... 14.4 ... 14.2 14.9 ... 14.7 ... 14.4 1710–2180 MHz (Syst. bottom) 14.5 ... 14.5 ... 14.2 1710–2180 MHz (Syst. top) 14.0 ... 14.0 ... 13.7 Tilt 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° 0° ... 7° ... 14° Horizontal Pattern: Half-power beam width 69° 68° 67° 67° Front-to-back ratio (180°±30°) > 25 dB Cross polar ratio Typically: Maindirection 0° > 25 dB Sector ±60° > 10 dB Vertical Pattern: Half-power beam width 14.7° 14.3° 13.9° 13.8° Electrical tilt 0°–14°, continuously adjustable Syst. bottom: Syst. top: 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T Sidelobe suppression for first 0° ... 7° ... 14° T 17 ... 16 ... 16 dB 18 ... 16 ... 16 dB 18 ... 17 ... 16 dB 18 ... 16 ... 15 dB sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 63° > 25 dB Typically: > 20 dB > 10 dB 60° 13.2° 12.6° 0°–14°, continuously adjustable 0°–14°, continuously adjustable 0° ... 7° ... 14° T 0° ... 7° ... 14° T 18 ... 17 ... 17 dB 18 ... 16 ... 17 dB < 1.5 > 30 dB > 35 dB (790–960 // 1710–2180 MHz) > 30 dB (1710–2180 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 6 x 7-16 female Bottom 3x, Position bottom, continuously adjustable Frontal / lateral / rearside: 480 / 300 / 700 N 1540 / 262 / 149 mm M (Medium) 21 kg / 23 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2180 –45° bottom 106 14.8 ... 14.8 ... 14.5 15.1 ... 14.8 ... 14.4 14.4 ... 14.3 ... 13.9 14.9 ... 14.8 ... 14.2 0° ... 7° ... 14° 0° ... 7° ... 14° 1710–2180 +45° bottom 1710–2180 –45° top 790–960 –45° 7-16 7-16 790–960 +45° 7-16 7-16 7-16 1710–2180 +45° top 7-16 For more information about additional mounting accessories please refer to page 191 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710–1880 1920–2170 X X X 65° 65° 65° XXXPol Panel 790–960/1710–1880/1920–2170 65°/65°/65° 16.5/18/18dBi 0°–10°/0°–6°/0°–6°T 1710 – 1880 1710 – 1880 MHz +45°, –45° 17.8 ... 18.0 ... 17.8 0° ... 3° ... 6° s clamped includ 1920 – 2170 1920 – 2170 MHz +45°, –45° 17.9 ... 18.2 ... 17.9 0° ... 3° ... 6° 65° > 30 dB Typically: > 25 dB > 10 dB 0.5 dB ±2.5° 61° > 30 dB Typically: > 25 dB > 10 dB 0.5 dB ±2.5° 5.0° 0°– 6° 0° ... 3° ... 6° T ≥ 18 ... 17 ... 15 dB 4.6° 0°– 6° 0° ... 3° ... 6° T ≥ 18 ... 18 ... 16 dB 742271V03 Type No. 790 – 960 Frequency range 790 – 862 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° Gain (dBi) 15.9 ... 15.8 ... 15.6 16.4 ... 16.3 ... 15.9 Tilt 0° ... 5° ... 10° 0° ... 5° ... 10° Horizontal Pattern: Half-power beam width 68° 65° Front-to-back ratio, copolar > 27 dB > 28 dB Cross polar ratio Typically: Typically: Maindirection > 25 dB 0° > 25 dB > 10 dB > 10 dB Sector ±60° Tracking, Avg. 1.5 dB Squint ±2.5° Vertical Pattern: Half-power beam width 10.9° 10° Electrical tilt, contin. adjust. 0°– 10° Sidelobe suppression for first 0° ... 5° ... 10° T 0° ... 5° ... 10° T sidelobe above main beam avg. ≥ 15 ... 16 ... 17 dB ≥ 15 ... 18 ... 19 dB VSWR Isolation: Intrasystem Isolation: Intersystem < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB Typically: > 50 dB (790 – 960 // 1710 – 1880 MHz) Typically: > 50 dB (790 – 960 // 1920 – 2170 MHz) > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc < –150 dBc < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 300 W* 600 W* 200 W* 200 W* 400 W* 400 W* 6 x 7-16 female (long neck) Bottom 3 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 860 / 380 / 920 N 1933 / 261 / 146 mm M (Medium) 24 kg / 26 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter * (at 50 °C ambient temperature) 1710–1880 –45° 790–960 –45° 790–960 +45° 7-16 7-16 1710 –1880 +45° 1920–2170 1920–2170 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 107 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710–2180 1710–2180 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2180/1710–2180 65°/65°/65° 16.5/16.5/16.5dBi 2°–14°/0°–14°/0°–14°T Frequency range Polarization Average gain: (dBi) 1710–2180 MHz (Syst. bottom) 1710–2180 MHz (Syst. top) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Cross polar ratio Maindirection 0° ±60° Sector Tracking Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam 790 – 866 MHz +45°, –45° 16.2 ... 16.0 ... 15.7 790 – 960 824 – 894 MHz +45°, –45° 16.3 ... 16.1 ... 15.8 880 – 960 MHz +45°, –45° 16.4 ... 16.2 ... 15.8 2° ... 8° ... 14° 2° ... 8° ... 14° 68° > 25 dB Typically: > 25 dB > 10 dB 67° > 25 dB Typically: > 25 dB > 10 dB 1.0 dB 16.2 ... 16.2 ... 15.7 16.1 ... 16.1 ... 15.4 0° ... 7° ... 14° 16.3 ... 16.3 ... 15.8 16.3 ... 16.2 ... 15.5 0° ... 7° ... 14° 65° > 25 dB Typically: > 25 dB > 10 dB 65° > 25 dB Typically: > 18 dB > 10 dB 64° > 25 dB Typically: > 19 dB > 10 dB 1.0 dB 60° > 25 dB Typically: > 20 dB > 10 dB 9.7° 9.3° 2°–14°, continuously adjustable 2° ... 8° ... 14° T 2° ... 8° ... 14° T 2° ... 8° ... 14° T 17 ... 17 ... 15 dB 17 ... 17 ... 16 dB 17 ... 17 ... 16 dB 9.5° 9° 8.7° 0°–14°, continuously adjustable 0° ... 7° ... 14° T 0° ... 7° ... 14° T 0° ... 7° ... 14° T 18 ... 17 ... 17 dB 18 ... 17 ... 17 dB 18 ... 17 ... 17 dB < 1.5 > 30 dB > 35 dB (790–960 // 1710–2180 MHz) > 30 dB (1710–2180 // 1710–2180 MHz) < –153 dBc (2 x 43 dBm carrier) 400 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 6 x 7-16 female (long neck) Bottom 3x, Position bottom, continuously adjustable Frontal / lateral / rearside: 640 / 400 / 950 N 2058 / 262 / 149 mm M (Medium) 27 kg / 29 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1710–2180 –45° bottom 108 2° ... 8° ... 14° 15.9 ... 15.9 ... 15.5 15.8 ... 15.8 ... 15.4 0° ... 7° ... 14° 10° VSWR Isolation: Intrasystem Isolation: Intersystem s clamped includ 1710 – 2180 1710 – 2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° 80010291V02 Type No. 1710–2180 +45° bottom 1710–2180 –45° top 790–960 –45° 7-16 7-16 790–960 +45° 7-16 7-16 7-16 1710–2180 +45° top 7-16 For more information about additional mounting accessories please refer to page 191 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710–1880 1920–2170 X X X 65° 65° 65° XXXPol Panel 790–960/1710–1880/1920–2170 65°/65°/65° 17.5/18/18dBi 0°–7°/0°–6°/0°–6°T 1710 – 1880 1710 – 1880 MHz +45°, –45° 17.8 ... 18.0 ... 17.8 0° ... 3° ... 6° s clamped includ 1920 – 2170 1920 – 2170 MHz +45°, –45° 17.9 ... 18.2 ... 17.9 0° ... 3° ... 6° 65° > 30 dB Typically: > 25 dB > 10 dB 0.5 dB ±2.5° 61° > 30 dB Typically: > 25 dB > 10 dB 0.5 dB ±2.5° 5.0° 0°– 6° 0° ... 3° ... 6° T ≥ 18 ... 17 ... 15 dB 4.6° 0°– 6° 0° ... 3° ... 6° T ≥ 18 ... 18 ... 16 dB 742272V03 Type No. 790 – 960 Frequency range 790 – 862 MHz 880 – 960 MHz Polarization +45°, –45° +45°, –45° Gain (dBi) 16.9 ... 16.9 ... 16.8 17.3 ... 17.4 ... 17.2 Tilt 0° ... 3° ... 7° 0° ... 3° ... 7° Horizontal Pattern: Half-power beam width 68° 65° Front-to-back ratio, copolar > 30 dB > 30 dB Cross polar ratio Typically: Typically: Maindirection > 30 dB > 30 dB 0° ±60° > 10 dB > 10 dB Sector Tracking, Avg. 1.0 dB Squint ±2.5° Vertical Pattern: Half-power beam width 8.0° 7.2° Electrical tilt, contin. adjust. 0°– 7° Sidelobe suppression for first 0° ... 4° ... 7° T 0° ... 4° ... 7° T sidelobe above main beam avg. ≥ 17 ... 17 ... 15 dB ≥ 18 ... 17 ... 15 dB VSWR Isolation: Intrasystem Isolation: Intersystem < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB Typically: > 50 dB (790 – 960 // 1710 – 1880 MHz) Typically: > 50 dB (790 – 960 // 1920 – 2170 MHz) > 30 dB (1710 – 1880 // 1920 – 2170 MHz) < –150 dBc < –150 dBc < –150 dBc Intermodulation IM3 (2 x 43 dBm carrier) Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 500 W* 1000 W* 250 W* 250 W* 500 W* 500 W* 6 x 7-16 female (long neck) Bottom 3 x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1160 / 500 / 1210 N 2533 / 261 / 146 mm H (Heavy) 29 kg / 31 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) 1710–1880 –45° 790–960 –45° 790–960 +45° 7-16 7-16 1710 –1880 +45° 1920–2170 1920–2170 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 109 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710–2180 1710–2180 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2180/1710–2180 65°/65°/65° 17.5/17.5/17dBi 2°–10°/0°–10°/0°–10°T Frequency range Polarization Average gain: (dBi) 1710–2180 MHz (Syst. bottom) 1710–2180 MHz (Syst. top) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° ±60° Tracking, Avg. 1710–2180 MHz (Syst. bottom) 1710–2180 MHz (Syst. top) Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem 790 – 862 MHz +45°, –45° 17.0 ... 17.0 ... 16.8 790 – 960 824 – 894 MHz +45°, –45° 17.2 ... 17.2 ... 16.9 880 – 960 MHz +45°, –45° 17.4 ... 17.4 ... 17.0 2° ... 6° ... 10° 2° ... 6° ... 10° 69° > 30 dB Typically: > 25 dB > 10 dB avg. 20 dB 68° > 30 dB Typically: > 25 dB > 10 dB avg. 20 dB 1.0 dB 2° ... 6° ... 10° 17.1 ... 17.2 ... 16.6 16.5 ... 16.7 ... 16.2 0° ... 5° ... 10° 17.2 ... 17.4 ... 16.8 16.6 ... 16.8 ... 16.3 0° ... 5° ... 10° 17.2 ... 17.3 ... 16.7 16.8 ... 17.0 ... 16.3 0° ... 5° ... 10° 66° > 30 dB Typically: > 25 dB > 10 dB avg. 17 dB 65° > 30 dB Typically: > 25 dB > 10 dB avg. 16 dB 62° > 30 dB Typically: > 25 dB > 10 dB avg. 16 dB 61° > 30 dB Typically: > 25 dB > 10 dB avg. 16 dB 1.0 dB 0.5 dB ±3.5° ±3.5° 7.8° 7.6° 7.1° 2°–10°, continuously adjustable 2° ... 6° ... 10° T 2° ... 6° ... 10° T 2° ... 6° ... 10° T 17 ... 16 ... 14 dB 18 ... 16 ... 15 dB 18 ... 16 ... 15 dB < 1.5 > 30 dB 7.6° 7.5° 6.8° 0°–10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 15 ... 16 ... 15 dB 16 ... 16 ... 15 dB 16 ... 16 ... 14 dB < 1.5 < 1.5 < 1.5 < 1.5 > 30 dB > 30 dB > 30 dB > 30 dB > 36 dB (790–960 // 1710–2180 MHz) > 36 dB (1710–2180 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) 200 W (at 50 °C ambient temperature) 6 x 7-16 female Bottom 3x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1210 / 510 / 1270 N 2598 / 261 / 146 mm H (Heavy) 27 kg / 29 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Intermodulation IM3 Max. power per input Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB 1710 –2180 –45° 110 s clamped includ 1710 – 2180 1710 – 2180 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2180 MHz +45°, –45° +45°, –45° +45°, –45° 80010292V03 Type No. 1710 – 2180 +45° 790–960 –45° 790–960 +45° 7-16 7-16 1710 – 2180 1710 – 2180 –45° +45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2170 2490–2690 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2170/2490–2690 65°/65°/65° 15/17/16.5dBi 0°–16°/2°–10°/2°–10°T Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, continuously adjust. Min. sidelobe suppression for first sidelobe above main beam s clamped includ 790 – 960 1710 – 2170 2490 –2690 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 14.5 ... 14.4 ... 14.2 14.6 ... 14.5 ... 14.3 14.8 ... 14.6 ... 14.4 17.0 ... 17.0 ... 16.6 17.2 ... 17.2 ... 16.8 17.2 ... 17.2 ... 16.7 16.3 ... 16.6 ... 15.8 0° ... 8° ... 16° 0° ... 8° ... 16° 0° ... 8° ... 16° 2° ... 5° ... 10° 2° ... 5° ... 10° 2° ... 5° ... 10° 2° ... 5° ... 10° 80010674 69° 68° 67° 63° 63° 65° 65° > 25 dB Typically: > 25 dB > 10 dB > 25 dB Typically: > 25 dB > 9 dB > 25 dB Typically: > 23 dB > 8 dB > 25 dB Typically: > 18 dB > 9 dB > 25 dB Typically: > 21 dB > 9 dB > 25 dB Typically: > 23 dB > 10 dB > 25 dB Typically: > 23 dB > 8 dB 16.5° 16.0° 15° 6.2° 5.8° 5.7° 4.8° 0°–16° 2°–10° 2°–10° 0° ... 8° ... 16° T 0° ... 8° ... 16° T 0° ... 8° ... 16° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T 2° ... 5° ... 10° T 16 ... 15 ... 15 dB 16 ... 15 ... 15 dB 15 ... 15 ... 15 dB 14 ... 14 ... 15 dB 14 ... 15 ... 16 dB 14 ... 16 ... 17 dB 14 ... 16 ... 17 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB 500 W* 1000 W* < 1.5 > 28 dB > 30 dB (790–960 // 1710–2170 // 2490–2690MHz) < –150 dBc (2 x 43 dBm carrier) 200 W* 400 W* 6 x 7-16 female (long neck) Bottom 3x, Position bottom, continuously adjustable Frontal / lateral / rearside: 700 / 270 / 730 N 1403 / 300 / 152 mm M (Medium) 20 kg / 22 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2170 –45° 790–960 –45° 790–960 +45° 7-16 7-16 < 1.5 > 30 dB 200 W* 400 W* * (at 50 °C ambient temperature) 1710–2170 +45° 2490–2690 2490–2690 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 111 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2170 2490–2690 X X X 65° 65° 65° Preliminary Issue XXXPol Panel 790–960/1710–2170/2490–2690 65°/65°/65° 16/18/18dBi 0°–10°/2°–8°/2°–8°T Type No. s clamped includ 790 – 960 1710 – 2170 2490 –2690 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.0 ... 16.0 ... 15.6 16.1 ... 16.2 ... 15.8 16.1 ... 16.2 ... 15.9 18.0 ... 18.1 ... 17.8 18.1 ... 18.1 ... 17.7 18.4 ... 18.4 ... 17.8 17.5 ... 18.0 ... 17.7 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 2° ... 5° ... 8° 2° ... 5° ... 8° 2° ... 5° ... 8° 2° ... 5° ... 8° 80010675V01 Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width 68° 67° 65° 64° 65° 62° 63° Front-to-back ratio, copolar (180°±30°) > 27 dB > 27 dB > 27 dB > 22 dB > 24 dB > 26 dB > 22 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Typically: Maindirection 0° > 27 dB > 26 dB > 23 dB > 17 dB > 22 dB > 23 dB > 24 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Vertical Pattern: Half-power beam width 10.3° 10.1° 9.7° 5.0° 4.7° 4.4° 3.5° Electrical tilt, continuously adjust. 0°–10° 2°–8° 2°–8° Sidelobe suppression 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 2° ... 5° ... 8° T 2° ... 5° ... 8° T 2° ... 5° ... 8° T 2° ... 5° ... 8° T – for first sidelobe above main beam 19 ... 15 ... 15 dB 19 ... 18 ... 17 dB 19 ... 18 ... 18 dB 16 ... 18 ... 19 dB 18 ... 19 ... 19 dB 17 ... 19 ... 19 dB 16 ... 18 ... 19 dB – within 0°–20° sector above horizon 18 ... 15 ... 15 dB 18 ... 17 ... 16 dB 18 ... 17 ... 14 dB 16 ... 17 ... 18 dB 17 ... 16 ... 18 dB 17 ... 17 ... 16 dB 15 ... 17 ... 14 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply < 1.5 > 30 dB 500 W* 1000 W* < 1.5 > 28 dB > 30 dB (790–960 // 1710–2170 // 2490–2690MHz) < –150 dBc (2 x 43 dBm carrier) 200 W* 400 W* 6 x 7-16 female (long neck) Bottom 3x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1020 / 390 / 1050 N 1997 / 300 / 152 mm M (Medium) 26 kg / 28 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2170 –45° 112 < 1.5 > 28 dB 200 W* 400 W* * (at 50 °C ambient temperature) 1710–2170 +45° 790–960 –45° 790–960 +45° 7-16 7-16 2490–2690 2490–2690 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2170 2490–2690 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2170/2490–2690 65°/65°/65° 17/18/18dBi 0°–10°/0°–6°/0°–6°T Type No. s clamped includ 790 – 960 1710 – 2170 2490 –2690 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 16.8 ... 16.7 ... 16.5 17.0 ... 17.0 ... 16.8 17.1 ... 17.2 ... 17.0 18.0 ... 18.0 ... 17.6 18.0 ... 18.0 ... 17.5 18.1 ... 18.1 ... 17.4 17.8 ... 17.8 ... 17.6 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0.5° ... 5° ... 9.5° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° 0° ... 3° ... 6° 80010676 Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width 68° 67° 65° 62° 63° 62° 63° Front-to-back ratio, copolar (180°±30°) > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB > 25 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Typically: Maindirection > 24 dB > 23 dB > 22 dB > 18 dB > 22 dB > 23 dB 0° > 25 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB > 10 dB Sector ±60° Vertical Pattern: Half-power beam width 7.5° 7.4° 7.1° 4.8° 4.6° 4.4° 3.5° Electrical tilt, continuously adjust. 0.5°–9.5° 0°–6° 0°–6° Min. sidelobe suppression for 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0.5° ... 5° ... 9.5° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T first sidelobe above main beam 18 ... 16 ... 14 dB 18 ... 17 ... 15 dB 18 ... 18 ... 16 dB 18 ... 16 ... 16 dB 18 ... 18 ... 17 dB 18 ... 17 ... 17 dB 18 ... 18 ... 18 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply > 30 dB 500 W* 1000 W* < 1.5 > 28 dB > 30 dB (790–960 // 1710–2170 // 2490–2690MHz) < –150 dBc (2 x 43 dBm carrier) 200 W* 400 W* 6 x 7-16 female (long neck) Bottom 3x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1380 / 520 / 1490 N 2622 / 300 / 152 mm H (Heavy) 31 kg / 33 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2170 –45° 790–960 –45° 790–960 +45° 7-16 7-16 200 W* 400 W* * (at 50 °C ambient temperature) 1710–2170 +45° 2490–2690 2490–2690 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 113 Triple-band Panel Dual Polarization Half-power Beam Width 790 – 960 1710 – 2690 1710 – 2690 X X X 65° 65° 65° XXXPol Panel 790–960/1710–2690/1710–2690 65°/65°/65° 16/16/16dBi 0°–10°/2°–12°/2°–12°T 80010691 Type No. s clamped includ 790 – 960 1710 – 2690 1710 – 2690 Frequency range 790 – 862 MHz 824 – 894 MHz 880 – 960 MHz 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2490 – 2690 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 15.9 ... 16.0 ... 15.6 16.0 ... 16.2 ... 15.8 16.0 ... 16.3 ... 15.8 Average gain: (dBi) 15.6 ... 15.4 ... 15.2 15.5 ... 15.7 ... 15.4 15.8 ... 15.7 ... 15.1 16.0 ... 16.1 ... 15.7 1710–2690 MHz (Syst. bottom) 15.2 ... 15.2 ... 14.8 15.4 ... 15.4 ... 14.9 15.7 ... 15.4 ... 14.9 15.6 ... 15.8 ... 15.3 1710–2690 MHz (Syst. top) 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 2° ... 7° ... 12° 2° ... 7° ... 12° 2° ... 7° ... 12° 2° ... 7° ... 12° Tilt Horizontal Pattern: Half-power beam width 67° 66° 65° 63° 64° 65° 62° Front-to-back ratio, copolar (180°±30°) > 27 dB > 27 dB > 27 dB > 25 dB > 27 dB > 27 dB > 27 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Typically: Typically: Maindirection 0° > 24 dB > 24 dB > 22 dB > 18 dB > 21 dB > 21 dB > 22 dB Sector ±60° > 10 dB > 10 dB > 10 dB > 8 dB > 10 dB > 10 dB > 7 dB Vertical Pattern: Half-power beam width 10.3° 10° 9.6° 11° 10° 9.3° 7.8° Electrical tilt 0°–10°, continuously adjustable 2°–12°, continuously adjustable Min. sidelobe suppression 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T 2° ... 7° ... 12° T 2° ... 7° ... 12° T 2° ... 7° ... 12° T 2° ... 7° ... 12° T – for first sidelobe above main beam 18 ... 16 ... 15 dB 18 ... 18 ... 18 dB 18 ... 17 ... 17 dB 18 ... 18 ... 18 dB 17 ... 17 ... 17 dB 17 ... 17 ... 16 dB 18 ... 17 ... 18 dB – 20° sector 18 ... 16 ... 15 dB 18 ... 18 ... 16 dB 18 ... 17 ... 15 dB 18 ... 15 ... 15 dB 17 ... 16 ... 16 dB 17 ... 16 ... 14 dB 16 ... 15 ... 15 dB Impedance VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 50 Ω < 1.5 > 30 dB > 30 dB (790–960 // 1710–2690 MHz) > 30 dB (1710–2690 // 1710–2690MHz) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 200 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 400 W (at 50 °C ambient temperature) 6 x 7-16 female (long neck) Bottom 3x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1020 / 390 / 1050 N 1997 / 300 / 152 mm M (Medium) 26 kg / 28 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 1710–2690 –45° 114 > 28 dB 790–960 –45° 790–960 +45° 7-16 7-16 < 1.5 > 28 dB 1710–2690 +45° 1710–2690 1710–2690 +45° –45° 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 Triple-band Panel Dual Polarization Half-power Beam Width 698 – 960 1710 – 2690 1710 – 2690 X X X 65° 65° 65° XXXPol Panel 698–960/1710–2690/1710–2690 65°/65°/65° 17/17/17dBi 1°–10°/0°–10°/2°–10°T 80010692V01 Type No. Low band Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam 698– 960 698 – 820 MHz +45°, –45° 16.1 ... 16.2 ... 16.2 1.5° ... 6° ... 10° 790 – 862 MHz +45°, –45° 16.5 ... 16.7 ... 16.7 1.5° ... 6° ... 10° 824 – 894 MHz +45°, –45° 16.8 ... 16.9 ... 16.8 1.5° ... 6° ... 10° 880 – 960 MHz +45°, –45° 17.0 ... 17.2 ... 17.1 1.5° ... 6° ... 10° 69° 66° 66° 65° > 26 dB Typically: 25 dB > 9 dB > 27 dB Typically: > 23 dB > 10 dB > 27 dB Typically: > 22 dB > 10 dB > 27 dB Typically: 22 dB > 8 dB 8.5° 7.8° 7.6° 1.5°– 10°, continuously adjustable 18 ... 16 ... 16 dB 18 ... 17 ... 17 dB 1.5° ... 6° ... 10° T 1.5° ... 6° ... 10° T 17 ... 16 ... 15 dB 1.5° ... 6° ... 10° T VSWR Isolation: Intrasystem Isolation: Intersystem High band Frequency range Polarization Average gain: (dBi) 1710–2690 MHz (Syst. bottom) 1710–2690 MHz (Syst. top) Tilt Horizontal Pattern: Half-power beam width Syst. bottom: Syst. top: Front-to-back ratio, copolar (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Syst. bottom: Syst. top: Electrical tilt Min. sidelobe suppression for first sidelobe above main beam Syst. bottom: 18 ... 16 ... 16 dB 1.5° ... 6° ... 10° T 1710 – 2690 1710 – 2690 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2300 – 2400 MHz 2490 – 2690 MHz +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 0° ... 5° ... 10° 16.6 ... 16.6 ... 16.1 16.7 ... 16.8 ... 16.5 16.7 ... 16.9 ... 16.1 17.2 ... 16.7 ... 15.7 16.7 ... 17.0 ... 16.5 16.5 ... 16.5 ... 16.1 16.3 ... 16.5 ... 16.2 16.3 ... 16.5 ... 16.0 16.5 ... 16.3 ... 15.5 16.2 ... 17.0 ... 16.3 2° ... 6° ... 10° 2° ... 6° ... 10° 2° ... 6° ... 10° 2° ... 6° ... 10° 2° ... 6° ... 10° 63° 61° 61° 63° 62° 66° 60° 67° 63° 63° > 27 dB Typically: 18 dB > 8 dB > 27 dB Typically: > 23 dB > 10 dB > 26 dB Typically: > 22 dB > 10 dB > 27 dB Typically: 20 dB > 8 dB > 26 dB Typically: 20 dB > 8 dB 7.6° 6.5° 7.4° 7.2° 6.1° 6.2° 6.0° 5.5° 0°–10° (Syst. bottom), 2°–10° (Syst. top), continuously adjustable 0° ... 5° ... 10° T 17 ... 15 ... 14 dB 2° ... 6° ... 10° T Syst. top: 15 ... 17 ... 18 dB Intermodulation IM3 Max. power per input Total power 7.1° < 1.5 > 30 dB > 32 dB (698 – 960 // 1710 – 2690 MHz) > 32 dB (1710 – 2690 // 1710 – 2690MHz) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) Intermodulation IM3 Max. power per input Total power VSWR Isolation: Intrasystem Isolation: Intersystem s clamped includ 0° ... 5° ... 10° T 18 ... 17 ... 16 dB 2° ... 6° ... 10° T 16 ... 18 ... 18 dB 0° ... 5° ... 10° T 18 ... 18 ... 16 dB 2° ... 6° ... 10° T 15 ... 18 ... 18 dB 0° ... 5° ... 10° T 18 ... 18 ... 14 dB 2° ... 6° ... 10° T 18 ... 18 ... 17 dB 5.9° 4.9° 0° ... 5° ... 10° T 18 ... 18 ... 15 dB 2° ... 6° ... 10° T 16 ... 18 ... 17 dB < 1.5 > 28 dB > 32 dB (698 – 960 // 1710 – 2690 MHz) > 32 dB (1710 – 2690 // 1710 – 2690MHz) < –150 dBc (2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 400 W (at 50 °C ambient temperature) For more information about additional mounting accessories please refer to page 191 115 116 Summary – Directional Antennas XXXXPol / XXXXXPol 698...960 / 1710...2690 MHz XXXXXPol – Dual Polarization +45°/–45° Type XXXXXPol Panel 698–960 1710–2690 1710–2690 1710–2690 1710–2690 65° 65° 65° 65° 65° 17dBi 17.5dBi 17dBi 18dBi 17.5dBi Type No. Height [mm] Connector position Page 1°–10°T 2°–12°T 2°–12°T 2°–12°T 2°–12°T 80010892 2691 bottom 118 + 119 XXXXPol – Dual Polarization +45°/–45° XXXXPol Panel 790–960 790–960 1710–2180 1710–2180 65° 65° 60° 60° 16dBi 16dBi 18.5dBi 18.5dBi 0°–10°T 0°–10°T 0°–6°T 0°–6°T 80010825 1934 bottom 120 XXXXPol Panel 790–960 790–960 1710–2180 1710–2180 65° 65° 60° 60° 17dBi 17dBi 18.5dBi 18.5dBi 0°–8°T 0°–8°T 0°–6°T 0°–6°T 80010826 2399 bottom 121 XXXXPol Panel 790–862 880–960 1710–2170 2490–2690 65° 65° 65° 65° 14.5dBi 15dBi 17dBi 17dBi 0°–14°T 0°–14°T 2°–10°T 2°–10°T 80010804 1503 bottom 122 XXXXPol Panel 790–862 880–960 1710–2170 2490–2690 65° 65° 65° 65° 16dBi 16dBi 18dBi 18dBi 0°–10°T 0°–10°T 2°–8°T 2°–8°T 80010805 1997 bottom 123 XXXXPol Panel 790–960 1710–1880 1920–2170 2490–2690 65° 65° 65° 65° 15dBi 16.5dBi 16.5dBi 17dBi 0°–16°T 2°–10°T 2°–10°T 2°–10°T 80010684 1403 bottom 124 XXXXPol Panel 790–960 1710–1880 1920–2170 2490–2690 65° 65° 65° 65° 16dBi 17.5dBi 18dBi 18dBi 0°–10°T 2°–8°T 2°–8°T 2°–8°T 80010685V01 1997 bottom 125 XXXXPol Panel 790–960 1710–1880 1920–2170 2490–2690 65° 65° 65° 65° 17dBi 18dBi 18dBi 18dBi 0°–10°T 2°–8°T 2°–8°T 2°–8°T 80010686V01 2622 bottom 126 New or changed product ying , deplo as Whened antenn using r t e s i d l i the so cons ombiners dC e al a ple s Quad-ban 232) e l a g speci (see pa 117 Penta Array Panel Dual Polarization HPBW 698–960 1710–2690 1710–2690 1710–2690 1710–2690 X X X X X 65° 65° 65° 65° 65° Preliminary Issue XXXXXPol Panel 6 98–960/1710–2690/1710–2690/1710–2690/1710–2690 65°/65°/65°/65°/65° 17/17.5/17/18/17.5dBi 1°–10°/2°–12°/2°–12°/2°–12°/2°–12°T 80010892 Type No. Left side, low band Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar (180°±30°) Cross polar ratio 0° Maindirection Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt Min. sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power 698 – 820 MHz +45°, –45° 16.2 ... 16.3 ... 16.2 1.5° ... 6° ... 10° 698 – 960 790 – 862 MHz 824 – 894 MHz +45°, –45° +45°, –45° 16.6 ... 16.7 ... 16.7 16.9 ... 17.0 ... 16.9 1.5° ... 6° ... 10° 1.5° ... 6° ... 10° s clamped includ 880 – 960 MHz +45°, –45° 17.2 ... 17.4 ... 17.2 1.5° ... 6° ... 10° 69° 67° 66° 65° > 25 dB Typically: > 24 dB > 8 dB > 25 dB Typically: > 24 dB > 8 dB > 25 dB Typically: > 24 dB > 8 dB > 28 dB Typically: > 25 dB > 8 dB 8.6° 18 ... 16 ... 15 dB 1.5° ... 6° ... 10° T 7.8° 7.6° 1.5°– 10°, continuously adjustable 18 ... 17 ... 17 dB 18 ... 17 ... 17 dB 1.5° ... 6° ... 10° T 1.5° ... 6° ... 10° T 7.1° 18 ... 16 ... 16 dB 1.5° ... 6° ... 10° T < 1.5 > 30 dB > 30 dB (698 – 960 // 1710 – 2690 MHz) > 30 dB (1710 – 2690 // 1710 – 2690MHz) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) Left side, high band 1710 – 2690 1710 – 2690 Frequency range 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2300 – 2400 MHz 2490 – 2690 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average gain: (dBi) 1710–2690 MHz (Syst. bottom) 17.2 ... 17.3 ... 17.0 17.5 ... 17.5 ... 17.2 17.6 ... 17.5 ... 17.1 17.0 ... 17.2 ... 16.9 17.3 ... 17.5 ... 17.0 16.6 ... 16.6 ... 16.3 17.0 ... 16.8 ... 16.5 17.0 ... 17.0 ... 16.5 16.5 ... 16.7 ... 16.4 16.7 ... 17.0 ... 16.5 1710–2690 MHz (Syst. top) 2° ... 7° ... 12° 2° ... 7° ... 12° 2° ... 7° ... 12° 2° ... 7° ... 12° 2° ... 7° ... 12° Tilt Horizontal Pattern: Half-power beam width 64° 63° 63° 63° 67° Front-to-back ratio, copolar (180°±30°) > 26 dB > 27 dB > 27 dB > 26 dB > 25 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection 0° 17 dB 22 dB > 23 dB 17 dB 16 dB Sector ±60° > 8 dB > 8 dB > 10 dB > 8 dB > 8 dB Vertical Pattern: Half-power beam width 7.3° 6.9° 6.5° 5.7° 5.2° Electrical tilt 2°–12° (Syst. bottom), 2°– 12° (Syst. top), continuously adjustable Min. sidelobe suppression for first sidelobe above 18 ... 18 ... 16 dB 18 ... 18 ... 15 dB 18 ... 18 ... 15 dB 18 ... 17 ... 14 dB main beam Syst. bottom: 18 ... 17 ... 15 dB 18 ... 17 ... 14 dB 18 ... 18 ... 15 dB 18 ... 17 ... 14 dB 18 ... 18 ... 15 dB Syst. top: 18 ... 17 ... 15 dB 2° ... 7° ... 12° T Tilt 2° ... 7° ... 12° T 2° ... 7° ... 12° T 2° ... 7° ... 12° T 2° ... 7° ... 12° T VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power 118 < 1.5 > 28 dB > 30 dB (698 – 960 // 1710 – 2690 MHz) > 30 dB (1710 – 2690 // 1710 – 2690MHz) < –150 dBc (2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 400 W (at 50 °C ambient temperature) For more information about additional mounting accessories please refer to page 191 80010892 Type No. Right side, high band 1710 – 2690 1710 – 2690 Frequency range 1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz 2300 – 2400 MHz 2490 – 2690 MHz Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45° Average gain: (dBi) 1710–2690 MHz (Syst. bottom) 17.2 ... 17.2 ... 17.1 17.4 ... 17.4 ... 17.2 17.6 ... 17.7 ... 17.5 17.8 ... 18.1 ... 17.9 18.0 ... 18.3 ... 17.6 16.7 ... 16.7 ... 16.8 16.8 ... 16.9 ... 16.8 17.0 ... 17.2 ... 17.0 17.2 ... 17.5 ... 17.4 17.2 ... 17.6 ... 16.9 1710–2690 MHz (Syst. top) 2.5° ... 7° ... 12° 2.5° ... 7° ... 12° 2.5° ... 7° ... 12° 2.5° ... 7° ... 12° 2.5° ... 7° ... 12° Tilt Horizontal Pattern: Half-power beam width 67° 66° 66° 66° 64° Front-to-back ratio, copolar (180°±30°) > 25 dB > 25 dB > 26 dB > 28 dB > 25 dB Cross polar ratio Typically: Typically: Typically: Typically: Typically: Maindirection 17 dB 0° > 19 dB > 18 dB 17 dB 18 dB ±60° > 9 dB > 10 dB > 10 dB Sector > 9 dB > 9 dB Vertical Pattern: Half-power beam width 7.2° 6.8° 6.4° 5.6° 5.0° Electrical tilt 2.5°–12° (Syst. bottom), 2.5°– 12° (Syst. top), continuously adjustable Min. sidelobe suppression for first sidelobe above 18 ... 18 ... 18 dB 17 ... 18 ... 18 dB 18 ... 18 ... 18 dB main beam 18 ... 18 ... 18 dB Syst. bottom: 17 ... 18 ... 17 dB 18 ... 17 ... 18 dB 17 ... 15 ... 16 dB 16 ... 15 ... 16 dB 18 ... 17 ... 18 dB Syst. top: 16 ... 15 ... 15 dB Tilt 2.5° ... 7° ... 12° T 2.5° ... 7° ... 12° T 2.5° ... 7° ... 12° T 2.5° ... 7° ... 12° T 2.5° ... 7° ... 12° T VSWR Isolation: Intrasystem Isolation: Intersystem < 1.5 > 28 dB > 30 dB (698 – 960 // 1710 – 2690 MHz) > 30 dB (1710 – 2690 // 1710 – 2690MHz) < –150 dBc (2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 400 W (at 50 °C ambient temperature) 10 x 7-16 female (long neck) Bottom 5 x, Position bottom continuously adjustable Frontal / lateral / rearside: 1710 / 560 / 1760 N 200 km/h 2691 / 377 / 169 mm H (Heavy) Panel and 2 units of clamps for 42 – 115 mm diameter Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 698 – 960 –45° 698 – 960 +45° 1710 –2690 1710 –2690 –45° +45° 1710 –2690 1710 –2690 –45° +45° 1710 –2690 1710 –2690 +45° –45° 1710 –2690 1710 –2690 +45° –45° 7-16 7-16 7-16 7-16 7-16 7-16 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 119 2-Dual-band Panel Dual Polarization Half-power Beam Width 790–960 790–960 1710–2180 1710–2180 X X X X 65° 65° 60° 60° XXXXPol Panel 790–960/790–960/1710–2180/1710–2180 65°/65°/60°/60° 16/16/18.5/18.5dBi 0°–10°/0°–10°/0°–6°/0°–6°T 80010825 Type No. Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam avg. 790 – 862 MHz +45°, –45° 15.4 ... 15.7 ... 15.3 0° ... 5° ... 10° 67° > 27 dB Typically: > 25 dB > 10 dB 880 – 960 MHz +45°, –45° 15.9 ... 16.1 ... 15.4 0° ... 5° ... 10° 1710 – 1880 MHz +45°, –45° 18.4 ... 18.5 ... 18.1 0° ... 3° ... 6° 63° > 28 dB Typically: > 25 dB > 10 dB 60° > 30 dB Typically: > 25 dB > 10 dB 65° > 27 dB Typically: > 25 dB > 10 dB 1.5 dB ±3.0° 11° 1710 – 2180 1850 – 1990 MHz +45°, –45° 18.5 ... 18.7 ... 18.1 0° ... 3° ... 6° 60° > 30 dB Typically: > 25 dB > 10 dB 0.5 dB ±2.5° 1920 – 2180 MHz +45°, –45° 18.3 ... 18.5 ... 18.1 0° ... 3° ... 6° 60° > 30 dB Typically: > 25 dB > 10 dB 10.7° 10° 0°–10°, continuously adjustable 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° T ≥ 17 ... 17 ... 17 dB ≥ 17 ... 17 ... 18 dB ≥ 17 ... 17 ... 16 dB 4.8° 4.6° 0°–6°, continuously adjustable 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T ≥ 16 ... 15 ... 14 dB ≥ 17 ... 16 ... 15 dB ≥ 17 ... 16 ... 15 dB < 1.5 > 30 dB < 1.5 > 30 dB VSWR Isolation: Intrasystem Isolation: Intersystem 5.0° > 30 dB (790–960 // 790–960 MHz) > 30 dB (790–960 // 1710–2180 MHz) > 30 dB (1710–2180 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 8 x 7-16 female Bottom 4x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1540 / 330 / 1790 N 1934 / 576 / 133 mm H (Heavy) 36 kg / 38 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790–960 –45° 1710 –2180 –45° 790 – 960 –45° 1710–2180 –45° 790–960 +45° 1710 –2180 +45° 790 – 960 +45° 1710 – 2180 +45° 7-16 120 790 – 960 824 – 894 MHz +45°, –45° 15.6 ... 16.0 ... 15.4 0° ... 5° ... 10° s clamped d lu c in 7-16 7-16 7-16 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 2-Dual-band Panel Dual Polarization Half-power Beam Width 790–960 790–960 1710–2180 1710–2180 X X X X 65° 65° 60° 60° XXXXPol Panel 790–960/790–960/1710–2180/1710–2180 65°/65°/60°/60° 17/17/18.5/18.5dBi 0°–7°/0°–7°/0°–6°/0°–6°T 80010826 Type No. Frequency range Polarization Gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar Cross polar ratio Maindirection 0° Sector ±60° Tracking, Avg. Squint Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam avg. 790 – 862 MHz +45°, –45° 16.3 ... 16.5 ... 16.2 0° ... 3° ... 7° 790 – 960 824 – 894 MHz +45°, –45° 16.6 ... 16.8 ... 16.3 0° ... 3° ... 7° 67° > 27 dB Typically: > 25 dB > 10 dB 880 – 960 MHz +45°, –45° 16.6 ... 17.0 ... 16.4 0° ... 3° ... 7° 1710 – 1880 MHz +45°, –45° 18.5 ... 18.5 ... 18.1 0° ... 3° ... 6° 63° > 28 dB Typically: > 25 dB > 10 dB 60° > 30 dB Typically: > 25 dB > 10 dB 65° > 27 dB Typically: > 25 dB > 10 dB 1.5 dB ±3.0° 7.7° 1710 – 2180 1850 – 1990 MHz +45°, –45° 18.5 ... 18.5 ... 18.1 0° ... 3° ... 6° 60° > 30 dB Typically: > 25 dB > 10 dB 0.5 dB ±2.5° s clamped d lu c in 1920 – 2180 MHz +45°, –45° 18.4 ... 18.5 ... 18.1 0° ... 3° ... 6° 60° > 30 dB Typically: > 25 dB > 10 dB 7.5° 7.2° 0°–7°, continuously adjustable 0° ... 3° ... 7° T 0° ... 3° ... 7° T 0° ... 3° ... 7° T ≥ 16 ... 17 ... 16 dB ≥ 15 ... 17 ... 18 dB ≥ 15 ... 17 ... 18 dB 4.8° 4.6° 0°–6°, continuously adjustable 0° ... 3° ... 6° T 0° ... 3° ... 6° T 0° ... 3° ... 6° T ≥ 16 ... 15 ... 14 dB ≥ 17 ... 16 ... 15 dB ≥ 17 ... 16 ... 15 dB < 1.5 > 30 dB < 1.5 > 30 dB VSWR Isolation: Intrasystem Isolation: Intersystem 5.0° > 30 dB (790–960 // 790–960 MHz) > 30 dB (790–960 // 1710–2180 MHz) > 30 dB (1710–2180 // 1710–2180 MHz) < –150 dBc (2 x 43 dBm carrier) < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 250 W (at 50 °C ambient temperature) 1000 W (at 50 °C ambient temperature) 500 W (at 50 °C ambient temperature) 8 x 7-16 female Bottom 4x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1930 / 410 / 2200 N 2399 / 576 / 133 mm H (Heavy) 39 kg / 41 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790–960 –45° 1710 –2180 –45° 790 – 960 –45° 1710–2180 –45° 790–960 +45° 1710 –2180 +45° 790 – 960 +45° 1710 – 2180 +45° 7-16 7-16 7-16 7-16 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 121 Quad-band Panel Dual Polarization Half-power Beam Width 790–862 880–960 1710–2170 2490–2690 X X X X 65° 65° 65° 65° XXXXPol Panel 790–862/880–960/1710–2170/2490–2690 65°/65°/65°/65° 14.5/15/17/17dBi 0°–14°/0°–14°/2°–10°/2°–10°T Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copalar (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, continuously adjust. Sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped d lu c in 80010804 Type No. 790 – 862 790 – 862 MHz +45°, –45° 14.2 ... 14.5 ... 14.1 0° ... 7° ... 14° 880 – 960 880 – 960 MHz +45°, –45° 14.6 ... 15.1 ... 14.5 0° ... 7° ... 14° 1710 – 1880 MHz +45°, –45° 16.9 ... 17 ... 16.6 2° ... 6° ... 10° 1710 – 2170 1850 – 1990 MHz +45°, –45° 17 ... 17.1 ... 16.5 2° ... 6° ... 10° 1920 – 2170 MHz +45°, –45° 16.9 ... 17 ... 16.5 2° ... 6° ... 10° 2490 – 2690 2490 – 2690 MHz +45°, –45° 16.5 ... 17 ... 16.7 2° ... 6° ... 10° 68° 65° 62° 64° 64° 63° > 26 dB Typically: > 25 dB > 10 dB > 26 dB Typically: > 25 dB > 10 dB > 25 dB Typically: > 18 dB > 10 dB > 25 dB Typically: > 21 dB > 10 dB > 25 dB Typically: > 21 dB > 10 dB > 25 dB Typically: > 23 dB > 10 dB 13.8° 0°–14° 12.3° 0°–14° 6.8° 6.2° 2°–10° 5.8° 4.6° 2°–10° 0° ... 7° ... 14° 18 ... 18 ... 16 dB 0° ... 7° ... 14° 18 ... 18 ... 18 dB 2° ... 6° ... 10° T 18 ... 18 ... 18 dB 2° ... 6° ... 10° T 16 ... 18 ... 18 dB 2° ... 6° ... 10° T 15 ... 17 ... 18 dB 2° ... 6° ... 10° T 15 ... 15 ... 17 dB < 1.5 > 30 dB < 1.5 > 30 dB < 1.5 > 28 dB > 30 dB (790...960 // 1710–2170 MHz // 2490–2690 MHz) > 28 dB, Typ. > 30 dB (790–862 // 880–960 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W* 200 W* 1000 W* 400 W* 8 x 7-16 female (long neck) Bottom 4x, Position bottom, continuously adjustable Frontal / lateral / rearside: 750 / 290 / 780 N 1503 / 300 / 152 mm M (Medium) 25 kg / 27 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter 500 W* 1000 W* 1710 –2170 –45° 880–960 –45° 790–862 –45° 790–862 +45° 7-16 880 – 960 +45° < 1.5 > 28 dB 200 W* 400 W* * (at 50 °C ambient temperature) 1710 – 2170 +45° 2490 – 2690 2490 – 2690 –45° +45° 7-16 7-16 7-16 7-16 7-16 7-16 7-16 122 For more information about additional mounting accessories please refer to page 191 Quad-band Panel Dual Polarization Half-power Beam Width 790–862 880–960 1710–2170 2490–2690 X X X X 65° 65° 65° 65° XXXXPol Panel 790–862/880–960/1710–2170/2490–2690 65°/65°/65°/65° 16/16/18/18dBi 0°–10°/0°–10°/2°–8°/2°–8°T 80010805 Type No. Frequency range Polarization Average gain (dBi) Tilt Horizontal Pattern: Half-power beam width Front-to-back ratio, copalar (180°±30°) Cross polar ratio Maindirection 0° Sector ±60° Vertical Pattern: Half-power beam width Electrical tilt, contin. adjust. Sidelobe suppression for first sidelobe above main beam VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply s clamped d lu c in 790 – 862 790 – 862 MHz +45°, –45° 15.6 ... 15.7 ... 15.2 0° ... 5° ... 10° 880 – 960 880 – 960 MHz +45°, –45° 15.8 ... 15.9 ... 15.5 0° ... 5° ... 10° 1710 – 1880 MHz +45°, –45° 17.7 ... 17.9 ... 17.7 2° ... 5° ... 8° 1710 – 2170 1850 – 1990 MHz +45°, –45° 17.7 ... 17.9 ... 17.7 2° ... 5° ... 8° 1920 – 2170 MHz +45°, –45° 17.8 ... 18.0 ... 17.5 2° ... 5° ... 8° 2490 – 2690 2490 – 2690 MHz +45°, –45° 17.2 ... 17.8 ... 17.5 2° ... 5° ... 8° 67° 65° 64° 65° 65° 62° > 27 dB Typically: > 22 dB > 10 dB > 27 dB Typically: > 22 dB > 10 dB > 25 dB Typically: > 18 dB > 10 dB > 25 dB Typically: > 22 dB > 10 dB > 25 dB Typically: > 23 dB > 10 dB > 25 dB Typically: > 25 dB > 10 dB 10.1° 0°–10° 0° ... 5° ... 10° 18 ... 15 ... 15 dB 9.6° 0°–10° 0° ... 5° ... 10° 18 ... 18 ... 16 dB 4.7° 4.5° 2°–8° 2° ... 5° ... 8° T 18 ... 17 ... 17 dB 4.3° 3.5° 2°–8° 2° ... 5° ... 8° T 18 ... 18 ... 18 dB < 1.5 > 30 dB < 1.5 > 30 dB 2° ... 5° ... 8° T 18 ... 18 ... 18 dB < 1.5 > 28 dB > 30 dB (790...960 // 1710–2170 MHz // 2490–2690 MHz) > 28 dB, Typ. > 30 dB (790–862 // 880–960 MHz) < –150 dBc (2 x 43 dBm carrier) 250 W* 200 W* 500 W* 400 W* 8 x 7-16 female (long neck) Bottom 4x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1020 / 390 / 1050 N 1997 / 300 / 152 mm M (Medium) 30 kg / 32 kg (clamps incl.) Panel and 2 units of clamps for 50 – 115 mm diameter 250 W* 500 W* 1710 –2170 –45° 880–960 –45° 790–862 –45° 790–862 +45° 7-16 2° ... 5° ... 8° 18 ... 18 ... 17 dB 880 – 960 +45° < 1.5 > 28 dB 200 W* 400 W* * (at 50 °C ambient temperature) 1710 – 2170 +45° 2490 – 2690 2490 – 2690 –45° +45° 7-16 7-16 7-16 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 123 Quad-band Panel Dual Polarization Half-power Beam Width 790–960 1710–1880 1920–2170 2490–2690 X X X X 65° 65° 65° 65° XXXXPol Panel 790–960/1710–1880/1920–2170/2490–2690 65°/65°/65°/65° 15/16.5/16.5/17dBi 0°–16°/2°–10°/2°–10°/2°–10°T 80010684 Type No. Frequency range 790 – 862 MHz Polarization +45°, –45° Average gain (dBi) 14.5 ... 14.4 ... 14.1 Tilt 0° ... 8° ... 16° Horizontal Pattern: Half-power beam width 69° Front-to-back ratio, copolar (180°±30°) > 25 dB Cross polar ratio Typically: > 25 dB Maindirection 0° > 10 dB Sector ±60° Vertical Pattern: Half-power beam width 16.5° Electrical tilt, continuously adjust. Sidelobe suppression for 0° ... 8° ... 16° T – first sidelobe above main beam 17 ... 15 ... 16 dB – within 0°–20° sector above horizon 17 ... 15 ... 15 dB s clamped d lu c in 790 – 960 824 – 894 MHz +45°, –45° 14.6 ... 14.5 ... 14.2 0° ... 8° ... 16° 880 – 960 MHz +45°, –45° 14.8 ... 14.6 ... 14.2 0° ... 8° ... 16° 1710 – 1880 1710 – 1880 MHz +45°, –45° 16.1 ... 16.3 ... 16.1 2° ... 6° ... 10° 1920 – 2170 1920 – 2170 MHz +45°, –45° 16.3 ... 16.5 ... 16.1 2° ... 6° ... 10° 2490 – 2690 2490 – 2690 MHz +45°, –45° 16.5 ... 17.1 ... 16.6 2° ... 6° ... 10° 68° 67° 65° 64° 63° > 25 dB Typically: > 25 dB > 9 dB > 25 dB Typically: > 23 dB > 9 dB > 25 dB Typically: > 18 dB > 10 dB > 25 dB Typically: > 21 dB > 10 dB > 25 dB Typically: > 23 dB > 10 dB 16.0° 0°–16° 0° ... 8° ... 16° T 17 ... 15 ... 17 dB 17 ... 15 ... 16 dB 15.0° 6.8° 2°–10° 2° ... 6° ... 10° T 16 ... 15 ... 16 dB 15 ... 15 ... 16 dB 6.0° 2°–10° 2° ... 6° ... 10° T 15 ... 16 ... 17 dB 15 ... 16 ... 15 dB 4.8° 2°–10° 2° ... 6° ... 10° T 15 ... 16 ... 17 dB 15 ... 17 ... 14 dB VSWR Isolation: Intrasystem Isolation: Intersystem Intermodulation IM3 Max. power per input Total power Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 0° ... 8° ... 16° T 16 ... 15 ... 16 dB 16 ... 15 ... 15 dB < 1.5 < 1.5 < 1.5 < 1.5 > 30 dB > 28 dB > 28 dB > 28 dB > 30 dB (790–960 // 1710–1880 // 1710–2170 // 2490–2690 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W* 150 W* 150 W* 150 W* 1000 W* 300 W* 300 W* 300 W* 1000 W* 400 W* 8 x 7-16 female (long neck) Bottom 4x, Position bottom, continuously adjustable Frontal / lateral / rearside: 700 / 270 / 730 N 1403 / 300 / 152 mm M (Medium) 23 kg / 25 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) 1920–2170 1710–1880 –45° –45° 790–960 –45° 7-16 790–960 +45° 1710 –1880 1920–2170 +45° +45° 2490 –2690 2490 –2690 +45° –45° 7-16 7-16 7-16 7-16 7-16 7-16 7-16 124 For more information about additional mounting accessories please refer to page 191 Quad-band Panel Dual Polarization Half-power Beam Width 790–960 1710–1880 1920–2170 2490–2690 X X X X 65° 65° 65° 65° XXXXPol Panel 790–960/1710–1880/1920–2170/2490–2690 65°/65°/65°/65° 16/18/18/18dBi 0°–10°/0°–6°/0°–6°/0°–6°T 80010685V01 Type No. Frequency range 790 – 862 MHz Polarization +45°, –45° Average gain (dBi) 15.9 ... 15.9 ... 15.6 Tilt 0° ... 5° ... 10° Horizontal Pattern: Half-power beam width 67° Front-to-back ratio, copolar (180°±30°) > 27 dB Cross polar ratio Typically: > 27 dB Maindirection 0° > 10 dB Sector ±60° Vertical Pattern: Half-power beam width 10.1° Electrical tilt, continuously adjust. Sidelobe suppression 0° ... 5° ... 10° T – for first sidelobe above main beam 17 ... 15 ... 15 dB – within 0°–20° sector above horizon 17 ... 15 ... 15 dB s clamped d lu c in 790 – 960 824 – 894 MHz +45°, –45° 16.0 ... 16.0 ... 15.7 0° ... 5° ... 10° 880 – 960 MHz +45°, –45° 16.0 ... 16.1 ... 15.8 0° ... 5° ... 10° 1710 – 1880 1710 – 1880 MHz +45°, –45° 17.5 ... 17.6 ... 17.4 2° ... 4° ... 8° 1920 – 2170 1920 – 2170 MHz +45°, –45° 17.8 ... 18.0 ... 17.5 2° ... 4° ... 8° 2490 – 2690 2490 – 2690 MHz +45°, –45° 17.5 ... 18.0 ... 17.8 2° ... 4° ... 8° 66° 65° 62° 63° 63° > 27 dB Typically: > 27 dB > 10 dB > 27 dB Typically: > 22 dB > 10 dB > 25 dB Typically: > 18 dB > 10 dB > 27 dB Typically: > 23 dB > 10 dB > 26 dB Typically: > 24 dB > 10 dB 9.9° 0°–10° 0° ... 5° ... 10° T 18 ... 15 ... 16 dB 18 ... 15 ... 15 dB 9.5° 4.9° 2°–8° 2° ... 4° ... 8° T 15 ... 17 ... 18 dB 15 ... 16 ... 16 dB 4.3° 2°–8° 2° ... 4° ... 8° T 15 ... 17 ... 18 dB 15 ... 17 ... 16 dB 3.5° 2°–8° 2° ... 4° ... 8° T 15 ... 17 ... 18 dB 15 ... 17 ... 15 dB VSWR Isolation: Intrasystem Isolation: Intersystem 0° ... 5° ... 10° T 18 ... 16 ... 15 dB 18 ... 15 ... 15 dB < 1.5 > 30 dB < 1.5 < 1.5 < 1.5 > 28 dB > 28 dB > 28 dB > 32 dB (1710–1880 // 1920–2170 MHz) > 32 dB (790–960 // 1710–2170 MHz) > 32 dB (2490–2690 // 790–960 ... 1710–2170 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W* 200 W* 200 W* 200 W* 1000 W* 400 W* 8 x 7-16 female (long neck) Bottom 4x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1020 / 390 / 1050 N 1997 / 300 / 152 mm M (Medium) 29 kg / 31 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1920–2170 1710–1880 –45° –45° 790–960 –45° 7-16 790–960 +45° 1710 –1880 1920–2170 +45° +45° 2490 –2690 2490 –2690 +45° –45° 7-16 7-16 7-16 7-16 7-16 7-16 7-16 For more information about additional mounting accessories please refer to page 191 125 Quad-band Panel Dual Polarization Half-power Beam Width 790–960 1710–1880 1920–2170 2490–2690 X X X X 65° 65° 65° 65° Preliminary Issue XXXXPol Panel 790–960/1710–1880/1920–2170/2490–2690 65°/65°/65°/65° 17/18/18/18dBi 0°–10°/2°–8°/2°–8°/2°–8°T 80010686V01 Type No. Frequency range 790 – 866 MHz Polarization +45°, –45° Average gain (dBi) 16.9 ... 16.9 ... 16.7 Tilt 0.5° ... 5° ... 9.5° Horizontal Pattern: Half-power beam width 68° Front-to-back ratio, copolar (180°±30°) > 27 dB Cross polar ratio Typically: > 26 dB Maindirection 0° > 10 dB Sector ±60° Vertical Pattern: Half-power beam width 7.5° Electrical tilt, continuously adjust. Sidelobe suppression 0.5° ... 5° ... 9.5° T – for first sidelobe above main beam 19 ... 18 ... 16 dB – within 0°–20° sector above horizon 14 ... 14 ... 12 dB s clamped d lu c in 790 – 960 824 – 894 MHz +45°, –45° 17.1 ... 17.1 ... 16.9 0.5° ... 5° ... 9.5° 880 – 960 MHz +45°, –45° 17.1 ... 17.2 ... 17.1 0.5° ... 5° ... 9.5° 1710 – 1880 1710 – 1880 MHz +45°, –45° 17.5 ... 17.6 ... 17.4 2° ... 4° ... 8° 1920 – 2170 1920 – 2170 MHz +45°, –45° 17.8 ... 18.0 ... 17.5 2° ... 4° ... 8° 2490 – 2690 2490 – 2690 MHz +45°, –45° 17.5 ... 18.0 ... 17.8 2° ... 4° ... 8° 67° 65° 62° 63° 63° > 26 dB Typically: > 26 dB > 10 dB > 26 dB Typically: > 23 dB > 10 dB > 25 dB Typically: > 18 dB > 10 dB > 27 dB Typically: > 23 dB > 10 dB > 26 dB Typically: > 24 dB > 10 dB 7.3° 0.5°–9.5° 0.5° ... 5° ... 9.5° T 19 ... 19 ... 18 dB 14 ... 14 ... 13 dB 7.0° 4.9° 2°–8° 2° ... 4° ... 8° T 15 ... 17 ... 18 dB 15 ... 16 ... 16 dB 4.3° 2°–8° 2° ... 4° ... 8° T 15 ... 17 ... 18 dB 15 ... 17 ... 16 dB 3.5° 2°–8° 2° ... 4° ... 8° T 15 ... 17 ... 18 dB 15 ... 17 ... 15 dB VSWR Isolation: Intrasystem Isolation: Intersystem 0.5° ... 5° ... 9.5° T 19 ... 19 ... 19 dB 15 ... 15 ... 14 dB < 1.5 > 30 dB < 1.5 < 1.5 < 1.5 > 28 dB > 28 dB > 28 dB > 30 dB (1710–1880 // 1920–2170 MHz) > 35 dB (790–960 // 1710–2170 MHz) > 38 dB (2490–2690 // 790–960 ... 1710–2170 MHz) < –150 dBc (2 x 43 dBm carrier) 500 W* 200 W* 200 W* 200 W* 1000 W* 400 W* 8 x 7-16 female (long neck) Bottom 4x, Position bottom, continuously adjustable Frontal / lateral / rearside: 1380 / 520 / 1490 N 2622 / 300 / 152 mm H (Heavy) 34 kg / 36 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter * (at 50 °C ambient temperature) Intermodulation IM3 Max. power per input Total power Input Connector position Adjustment mechanism Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 1920–2170 1710–1880 –45° –45° 790–960 –45° 7-16 790–960 +45° 1710 –1880 1920–2170 +45° +45° 2490 –2690 2490 –2690 +45° –45° 7-16 7-16 7-16 7-16 7-16 7-16 7-16 126 For more information about additional mounting accessories please refer to page 191 Summary – Directional Antennas VPol 790...2690 MHz Vertical Polarization Type Type No. Height [mm] Connector female, type and position Page VPol Panel 870–960 20° 16.5dBi 0°T 735727 492 7-16, rearside 128 VPol Panel 790–960 65° 18.5dBi 0°T 730376V02 2574 7-16, rearside 129 VPol Panel 872–960 90° 7.5dBi 0°T 736854 262 N, bottom or top 130 VPol Panel 790–960 90° 17dBi 0°T 730378V02 2574 7-16, rearside 131 VPol – 800/900 / 1800/1900/2000 VPol Panel 1710–2180 12° 18.5dBi 0°T 80010368 299 7-16, side 132 Dual Yagi 790–960 1710–2170 C 38° 28° 14dBi 15.5dBi 0°T 0°T 80010828V01 170 7-16, rearside 133 VPol BiDir 790–960 / 1710–2170 65° 5dBi 0°T 738445 312 7-16, bottom 134 VPol BiDir 790–960 / 1710–2170 65° 5dBi 0°T 738446 312 N, bottom 134 790–2690 65° 11dBi 0°T 742192V01 300 7-16, bottom 135 VPol LogPer VVPol – 800/900 / 1800/1900/2000 VVPol Panel 824–960 1710–2170 C 90° 82° 7dBi 7dBi 0°T 0°T 742290 328 7-16, bottom or top 136 VVPol Panel 824–960 1710–2170 C 90° 82° 10dBi 11dBi 0°T 0°T 80010046V01 662 7-16, bottom or top 137 C = integrated Combiner New or changed product 127 Panel Vertical Polarization Half-power Beam Width VPol Panel 870–960 20° 16.5dBi Type No. Frequency range Polarization Gain Half-power beam width Impedance VSWR Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Packing size 870 – 960 V 20° 735727 870 – 960 MHz Vertical 16.5 dBi H-plane: 20° 33° E-plane: 50 Ω < 1.3 < –150 dBc ( 2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 7-16 female Rearside Frontal / lateral / rearside: 500 / 70 / 715 N 492 / 992 / 190 mm M (Medium) 1010 x 630 x 265 mm Material: Radiator: Aluminum. Reflector screen: Weatherproof aluminum. Radome: Fiberglass, color: White. All screws and nuts: Stainless steel. Ice protection: Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. Accessories (order separately) Weight Units per approx. antenna Type No. Description Remarks 731651 738546 85010002 85010003 1 clamp 1 clamp 1 clamp 1 clamp Mast: 28 – 60 mm diameter Mast: 50 – 115 mm diameter Mast: 110 – 220 mm diameter Mast: 210 – 380 mm diameter 128 0.8 kg 1.0 kg 2.7 kg 4.8 kg 2 2 2 2 For more information about additional mounting accessories please refer to page 191 Panel Vertical Polarization Half-power Beam Width VPol Panel 790–960 65° 18.5dBi Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon VSWR Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 790– 960 V 65° s clamped d lu c in 730376V02 17.8 dBi 790 – 960 824 – 894 MHz Vertical 18.0 dBi 68° > 25 dB 67° > 25 dB 65° > 25 dB 7.4° 7.2° 6.8° > 17 dB > 17 dB > 18 dB 790 – 862 MHz 880 – 960 MHz 18.4 dBi < 1.5 < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 7-16 female Rearside Frontal / lateral / rearside: 740 / 330 / 1270 N (at 150 km/h) 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 129 Panel Vertical Polarization Half-power Beam Width VPol Panel 872–960 90° 7.5dBi Type No. Frequency range 872 – 960 V 90° 736854 872 – 960 MHz Polarization Vertical Gain 7.5 dBi Half-power beam width H-plane: 90° E-plane: 70° Front-to-back ratio > 20 dB VSWR < 1.5 Intermodulation IM3 Max. power < –140 dBc (2 x 43 dBm carrier) 350 W (at 50 °C ambient temperature) Input N female Connector position Bottom or top Weight 1.5 kg Wind load (at 150 km/h) Frontal / lateral / rearside: 45 / 20 / 60 N Height/width/depth 262 / 155 / 49 mm Accessories (order separately) Type No. Description 734360 734361 734362 734363 734364 734365 738546 731651 85010002 85010003 2 tension bands 2 tension bands 2 tension bands 2 tension bands 2 tension bands 2 tension bands 1 clamp 1 clamp 1 clamp 1 clamp 130 Remarks Material Stainless steel Mast: 34 – 60 mm diameter Stainless steel Mast: 60 – 80 mm diameter Stainless steel Mast: 80 – 100 mm diameter Stainless steel Mast: 100 – 120 mm diameter Stainless steel Mast: 120 – 140 mm diameter Stainless steel Mast: 45 – 125 mm diameter Stainless steel Mast: 42 – 115 mm diameter Mast: 28 – 60 mm diameter Hot-dip galvanized steel Mast: 110 – 220 mm diameter Hot-dip galvanized steel Mast: 210 – 380 mm diameter Hot-dip galvanized steel Units Weight per approx. antenna 0.06 kg 0.07 kg 0.08 kg 0.09 kg 0.11 kg 0.08 kg 1.1 kg 0.8 kg 2.7 kg 4.8 kg 1 1 1 1 1 1 2 2 2 2 For more information about additional mounting accessories please refer to page 191 Panel Vertical Polarization Half-power Beam Width VPol Panel 790–960 90° 17dBi Impedance VSWR Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply V 90° s clamped includ 730378V02 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Vertical Pattern: Half-power beam width Sidelobe suppression for first sidelobe above horizon 790– 960 16.6 dBi 790 – 960 824 – 894 MHz Vertical 16.7 dBi 90° > 22 dB 90° > 22 dB 90° > 22 dB 7.1° 6.9° 6.6° > 12 dB > 12 dB > 12 dB 790 – 862 MHz 880 – 960 MHz 17.0 dBi 50 Ω < 1.5 < –150 dBc (2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 7-16 female Rearside Frontal / lateral / rearside: 930 / 410 / 1270 N 2574 / 259 / 99 mm H (Heavy) 12 kg / 14 kg (clamps incl.) Panel and 2 units of clamps for 42 – 115 mm diameter For more information about additional mounting accessories please refer to page 191 131 Multi-band Antenna Vertical Polarization Half-power Beam Width 1710 – 2180 V 12° VPol Panel 1710–2180 12° 18.5dBi 0°T 80010368 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Front-to-back ratio (180°±30°) Sidelobe suppression Vertical Pattern: Half-power beam width Electrical tilt Sidelobe supression for first sidelobe above main beam 1710 – 1880 MHz Vertical 18.1 dBi 1710 – 2180 1850 – 1990 MHz Vertical 18.4 dBi 1920 – 2180 MHz Vertical 18.7 dBi 13.3° > 30 dB > 18 dB 12.8° > 30 dB > 18 dB 12° > 30 dB > 17 dB 37° 36° 0°, fixed 36° > 18 dB > 18 dB > 18 dB VSWR Intermodulation IM3 Max. power per input Input Connector position Wind load (at 150 km/h) Height/width/depth Weight < 1.5 < –150 dBc (2 x 43 dBm carrier) 300 W (at 50 °C ambient temperature) 1 x 7-16 female Side (see picture) Frontal / lateral / rearside: 340 / 25 / 400 N 299 / 743 / 69 mm 9 kg Accessories (order separately) Type No. Description Remarks Weight approx. Units per antenna 738546 731651 85010002 85010003 1 clamp 1 clamp 1 clamp 1 clamp Mast: 42 – 115 mm diameter Mast: 28 – 60 mm diameter Mast: 110 – 220 mm diameter Mast: 210 – 380 mm diameter 1.1 kg 0.8 kg 2.7 kg 4.8 kg 2 (order separately if required) 2 (order separately if required) 2 (order separately if required) 2 (order separately if required) 132 For more information about additional mounting accessories please refer to page 191 Yagi Multi-band Antenna Dual Polarization Half-power Beam Width 790 – 960 1710 – 2170 +45° –45° 38° 28° Dual Yagi 790–960/1710–2170 C 38°/28° 14/15.5dBi 80010828V01 Type No. 790 – 960 790 – 870 MHz 870 – 960 MHz < 1.5 < 1.5 13 dBi 14 dBi +45° +45° ≥ 25 dB ≥ 25 dB Frequency range VSWR Gain (average) Polarization Front-to-back ratio Half-power beam width (avg.) horizontal vertical Max. power Input Connector position Weight Wind load Max. wind velocity Dimensions 38° 38° Integrated combiner 1710 – 2170 1710 – 1880 MHz 1920 – 2170 MHz < 1.5 < 1.5 13 dBi 15.5 dBi –45° –45° ≥ 27 dB ≥ 27 dB 32° 28° 32° 28° 100 W (at 50 °C ambient temperature) 1 x 7-16 female Rearside 6 kg / 10 kg (clamps incl.) 200 N (at 150 km/h) 215 km/h 1184 / ∅ 170 mm 22° 22° The insertion loss is included in the given antenna gain values. Please note: This antenna is suitable for tunnel applications. 790–960 +45° 1710–2170 –45° C 7-16 Material: Reflector: Aluminum, brass. Radome: Fiberglass, color: grey. Base: Weather-proof aluminum. All screws and nuts: Stainless steel. Mounting: The antenna can be mounted on a tubular mast with a diameter of 42 to 115 mm, with supplied clamps. Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. Environmental conditions: Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items: – Low temperature: –55 °C – High temperature (dry): +60 °C Environmental tests: The antenna has passed a pressure test and meets the requirements according to Official Journal of the European Communities L245/171 from 12.09.2002 for the use of the antenna in train tunnels for high speed railways. The antenna exceeds the standard as follows. Pressure difference according to L245/171: 10 kPa Pressure difference during test: 100 kPa (const. 24 h) 133 Multi-band Bidirectional Antenna 790–960/1710–2170 V Vertical Polarization 65° Half-power Beam Width VPol BiDir 790–960/1710–2170 65° 5dBi Type No. Input Frequency range VSWR Gain Impedance Polarization Intermodulation IM3 Max. power (total) Weight Half-power beam width Max. wind velocity Packing size Height/width/depth 738445 738446 1 x 7-16 female 1 x N female 790 – 960 MHz, 1710 – 2170 MHz 790 – 806 MHz: < 2.2 806 – 824 MHz: < 1.7 824 – 960 / 1710 – 2170 MHz: < 1.5 790 – 960 MHz: 5 dBi 1710 – 1880 MHz: 5.5 dBi 1880 – 2170 MHz: 6.5 dBi 50 Ω Vertical < –150 dBc ( 2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) 0.8 kg Frontal: 25 N (at 150 km/h) Lateral: 65 N (at 150 km/h) Rearside: 35 N (at 150 km/h) 200 km/h 422 x 212 x 95 mm 312 / 55 / 188 mm Material: Radiator: Tin-plated copper. Reflector: Weather-proof aluminum. Radome: High impact plastic, colour: Grey. All screws and nuts: Stainless steel. Mounting: Wall mounting: No additional mounting kit needed. For pipe mast mounting use clamps listed below (order separately). Ice protection: The radiating system is protected by the radome. Due to its very sturdy construction, the antenna remains operational even under icy conditions. Grounding: All metal parts of the antenna as well as the inner conductor are DC grounded. Accessories (order separately) Type No. 734360 734361 734362 734363 734364 734365 134 Description Remarks 2 clamps 2 clamps 2 clamps 2 clamps 2 clamps 2 clamps Mast: 34 – 60 mm diameter Mast: 60 – 80 mm diameter Mast: 80 – 100 mm diameter Mast: 100 – 120 mm diameter Mast: 120 – 140 mm diameter Mast: 45 – 125 mm diameter Weight Units per approx. antenna 60 g 70 g 80 g 90 g 110 g 80 g 1 1 1 1 1 1 Logarithmic Periodic Vertical Polarization Half-power Beam Width 790 – 2690 V 65° VPol LogPer 790–2690 65° 11dBi Type No. Frequency range VSWR Gain 742192V01 790 – 960 MHz 960 – 1710 MHz < 1.5 < 1.5 1710 – 2200 MHz 2200 – 2490 MHz 2490 – 2690 MHz < 1.5 < 1.5 < 1.6 10.8 dBi 11.0 dBi 11.2 dBi 11.0 dBi 10.8 dBi Impedance 50 Ω 50 Ω 50 Ω 50 Ω 50 Ω Polarization Vertical Vertical Vertical Vertical Vertical Front-to-back ratio > 25 dB > 25 dB > 25 dB > 22 dB > 25 dB 65° 53° 60° 50° 55° 47° 50° 45° 50° 45° < –150 dBc < –150 dBc < –150 dBc < –150 dBc < –150 dBc Half-power beam width horizontal vertical Intermodulation IM3 (2 x 43 dBm carrier) Max. power Total power Input 300 W 250 W 200 W 170 W 500 W (at 50 °C ambient temperature) 1 x 7-16 female Connector position Bottom Weight Wind load (at 150 km/h) Height/width/depth 150 W 5.5 kg Frontal / lateral / rearside: 20 / 210 / 30 N 300 / 155 / 785 mm Material: Radiator: Tin-plated copper. Reflector screen: Weather-proof aluminum. Radome: Fiberglass, color: Grey. All screws and nuts: Stainless steel Mounting: The antenna can be mounted on tubular mast with a diameter of 30 – 70 mm with supplied clamps. Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: All metal parts of the antenna as well as the inner c onductor are DC grounded. For more information about additional mounting accessories please refer to page 191 135 Dual-band Panel Vertical Polarization Half-power Beam Width 824 – 960 1710 – 2170 V V 90° 82° VVPol Panel 824–960/1710–2170 C 90°/82° 7/7dBi 742290 Type No. Frequency range Polarization Gain Half-power beam width Front-to-back ratio VSWR Intermodulation IM3 (2 x 43 dBm carrier) Max. power Input Connector position 824 – 960 MHz 1710 – 2170 MHz Vertical Vertical 7 dBi 7 dBi Horizontal: Vertical: 90° 60° > 18 dB Height/width/depth 82° 70° > 20 dB < 1.7 (824 – 960 MHz) < 1.7 (1710 – 2170 MHz) < 1.5 (870 – 960 MHz) < 1.5 (1710 – 1990 MHz) < –150 dBc < –150 dBc 100 W (at 50 °C ambient temperature) 1 x 7-16 female Bottom or top Weight Wind load (at 150 km/h) Horizontal: Vertical:       2.8 kg  Frontal / lateral / rearside: 90 / 23 / 100 N  328 / 155 / 69 mm VVPol Panel 824–960/1710–2170 C 90°/82° 10/11dBi Type No. 80010046 Frequency range(order separately) 824 – 960 MHz Accessories Polarization Type No. Description Gain Half-power beam width 734360 2 tension bands 734361 2 tension bands 734362 2 tension Front-to-back ratio bands 734363 2 tension bands VSWR 734364 2 tension bands 734365 2 tension Intermodulation IM3 bands 738546 1 clamp (2 x 43 dBm carrier) 731651 1 clamp Max. power 85010002 1 clamp Input 85010003 1 clamp Connector position 732327 1 downtilt kit Weight Wind load (at 150 km/h) Height/width/depth Vertical Remarks 10 dBi 1710 – 2170 MHz Vertical Material 11 dBi Horizontal: 90° diameterHorizontal: 82°steel Stainless Mast: 34 – 60 mm Vertical: 33° diameterVertical: 19°steel Stainless Mast: 60 – 80 mm Stainless steel Mast: 80 >– 18100 dB mm diameter > 20 dB steel Mast: diameter < 1.7100 (824– –120 960mm MHz) <Stainless 1.5 Stainless steel Mast: 120 – 140 mm diameter < 1.5 (870 – 960 MHz) Stainless Mast: <45–150 – 125 mm diameter dBc < –150 dBc steel Stainless steel Mast: 42 – 115 mm diameter Mast: 28 – 60 mm diameter Hot-dip galvanized steel 100 W (at 50 °C ambient temperature) Mast: 110 – 220 mm diameter Hot-dip galvanized steel 1 x 7-16 female Mast: 210 – 380 mm diameter Hot-dip galvanized steel Stainless steel Downtilt angle: 0° Bottom – 40° or top 5 kg Frontal / lateral / rearside: 175 / 47 / 200 N 662 / 155 / 69 mm Units Weight per approx. antenna 0.06 kg 0.07 kg 0.08 kg 0.09 kg 0.11 kg 0.08 kg 1.1 kg 0.8 kg 2.7 kg 4.8 kg 1.0 kg 1 1 1 1 1 1 2 2 2 2 1         136 For more information about additional mounting accessories please refer to page 191 Dual-band Panel Vertical Polarization Half-power Beam Width 824 – 960 1710 – 2170 V V 90° 82° VVPol Panel 824–960/1710–2170 C 90°/82° 10/11dBi Type No. Frequency range Polarization Gain Half-power beam width Front-to-back ratio VSWR Intermodulation IM3 ( 2 x 43 dBm carrier) Max. power per input Input Connector position* Wind load (at 150 km/h) Height/width/depth Category of mounting hardware Weight Scope of supply 80010046V01 824 – 960 MHz Vertical 10 dBi Horizontal: 90° Vertical: 33° > 18 dB < 1.7 (824 – 960 MHz) < 1.5 (870 – 960 MHz) < –150 dBc s clamped d lu c in 1710 – 2170 MHz Vertical 11 dBi Horizontal: 82° Vertical: 19° > 20 dB < 1.5 < –150 dBc 100 W (at 50 °C ambient temperature) 1 x 7-16 female Bottom or top Frontal / lateral / rearside: 165 / 55 / 190 N 662 / 155 / 69 mm L (Light) 824–960 VPol 5 kg (tension bands incl.) Panel and 1 unit of tension bands for 45 – 125 mm diameter 1710–2170 VPol C 7-16 Accessories Type No. Description Remarks Weight approx. Units per antenna 2 tension bands Mast: 45 – 125 mm diameter 0.08 kg 1 (included in the scope of supply) 734360 2 tension bands Mast: 34 – 60 mm diameter 0.06 kg 1 (order separately if required) 734361 2 tension bands Mast: 60 – 80 mm diameter 0.07 kg 1 (order separately if required) 734362 2 tension bands Mast: 80 – 100 mm diameter 0.08 kg 1 (order separately if required) 734363 2 tension bands Mast: 100 – 120 mm diameter 0.09 kg 1 (order separately if required) 734364 2 tension bands Mast: 120 – 140 mm diameter 0.11 kg 1 (order separately if required) 738546 1 clamp Mast: 42 – 115 mm diameter 1.1 kg 2 (order separately if required) 731651 1 clamp Mast: 28 – 60 mm diameter 0.8 kg 2 (order separately if required) 85010002 1 clamp Mast: 110 – 220 mm diameter 2.7 kg 2 (order separately if required) 85010003 1 clamp Mast: 210 – 380 mm diameter 4.8 kg 2 (order separately if required) 732327 1 downtilt kit Downtilt angle: 0° – 19° 1.0 kg 1 (order separately if required) 734365 For more information about additional mounting accessories please refer to page 191 137 138 Summary – Omnidirectional Antennas VPol, XPol 790...2700 MHz Vertical Polarization Type Type No. Connector Height female [mm] Remarks Page VPol Omni 870–960 360° 2dBi 0°T 738450 N 180 indoor/outdoor 140 VPol Omni 806–960 360° 2dBi 0°T K751161 N 348 141 VPol Omni 890–960 360° 5dBi 0°T K7515641 N 715 142 VPol Omni 870–960 360° 8dBi 0°T 736350 7-16 1543 143 VPol Omni 790–862 360° 11dBi 0°T 80010850 7-16 3237 144 VPol Omni 860–894 360° 11dBi 0°T 738192 7-16 3237 145 VPol Omni 870–960 360° 11dBi 0°T 736347 7-16 3033 146 VPol Omni 870–960 360° 10.5dBi 5°T 736349 7-16 2954 147 VVPol Omni 790–862 870–960 360° 360° 8dBi 9dBi 0°T 0°T 80010747 2 x 7-16 3237 790–960/1710–2700 360° 2dBi 0°T 80010847 N 194 870–960 1920–2170 360° 360° 9dBi 10dBi 0°T 0°T 80010274 2 x 7-16 3033 separate inputs 149 VVPol Omni 870–960/1710–1880 1920–2170 360° 360° 2dBi 2dBi 0°T 0°T 80010111 2xN 493 separate inputs 150 VPol Omni 1710–2700 360° 2dBi 0°T 80010431 N 115 165 VPol Omni 1710–1880 360° 11dBi 0°T 738187 7-16 1568 151 VPol Omni 1920–2170 360° 11dBi 0°T 741790 7-16 1387 152 VPol Omni 2500–2700 360° 11dBi 0°T 80010442 7-16 1132 153 VPol Omni VVPol Omni separate inputs 148 indoor/outdoor 166 Dual Polarization Type XPol Omni Type No. 1710–2690 360° 5dBi 0°T 80010126 Connector Height female [mm] 2xN 694 Remarks Page 154 New or changed product 139 Omnidirectional Antenna Vertical Polarization Type No. Input Connector position Frequency range VSWR Gain Impedance Intermodulation IM3 Polarization Max. power Weight Radome diameter Height V 738450 N female Bottom or top 870 – 960 MHz < 1.5 2 dBi 50 Ω < –150 dBc ( 2 x 43 dBm carrier) Vertical 100 W (at 50 °C ambient temperature) 200 g 20 mm 180 mm Material: Radiator: Brass. Radome: Fiberglass, colour: White. Mounting: One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. Grounding: All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 78° 3 0 dB 10 Vertical Pattern 140 180 mm VPol Omni 870–960 360° 2dBi 870 – 960 Omnidirectional Antenna Vertical Polarization VPol Omni 806–960 360° 2dBi Type No. V K751161 806 – 960 MHz Vertical 2 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 100 W (at 50 °C ambient temperature) 348 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 806 – 960 Mounting: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 – 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 – 54 mm diameter (connecting cable runs outside the mast). Material: Radiator: Brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Grounding: All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 78° 3 dB 10 0 Vertical Pattern Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height On the tip N female Bottom 0.74 kg 21 mm 17 N (at 150 km/h) 200 km/h 455 x 112 x 97 mm 348 mm Laterally at the tip Brackets for side mounting (see page 204) 141 Omnidirectional Antenna Vertical Polarization VPol Omni 890–960 360° 5dBi Type No. V K7515641 890 – 960 MHz Vertical 5 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 250 W (at 50 °C ambient temperature) Mounting: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 40 – 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 20 – 54 mm diameter (connecting cable runs outside the mast). Material: Radiator: Brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Grounding: All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. 715 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 890 – 960 30° 3 dB 10 0 Vertical Pattern Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height On the tip 142 N female Bottom 0.90 kg 21 mm 20 N (at 150 km/h) 200 km/h 825 x 112 x 97 mm 715 mm Laterally at the tip Brackets for side mounting (see page 204) Omnidirectional Antenna Vertical Polarization VPol Omni 870–960 360° 8dBi V 736350 Type No. 870 – 960 MHz Vertical 8 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 1543 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 870 – 960 13° 3 dB 10 0 Vertical Pattern Mechanical specifications 150 230 um maximtop mast Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 5.5 kg 51 mm 130 N (at 150 km/h) 200 km/h 1846 x 148 x 112 mm 1543 mm 104 Brackets for side mounting (see page 202 – 204) 143 Omnidirectional Antenna Vertical Polarization VPol Omni 790–894 360° 11dBi V 80010850 Type No. 790 – 862 MHz Vertical 11 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 3237 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 790 – 862 7° 3 dB 10 0 Vertical Pattern Mechanical specifications 150 230 um maximtop mast Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8.5 kg 51 mm 230 N (at 150 km/h) 180 km/h 3516 x 148 x 112 mm 3237 mm 104 144 Brackets for side mounting (see page 202 – 204) Omnidirectional Antenna Vertical Polarization VPol Omni 806–894 360° 11dBi V 738192 Type No. 806 – 894 MHz Vertical 11 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 3237 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 806 – 894 7° 3 dB 10 0 Vertical Pattern Mechanical specifications 150 230 um maximtop mast Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8.5 kg 51 mm 230 N (at 150 km/h) 180 km/h 3516 x 148 x 112 mm 3237 mm 104 Brackets for side mounting (see page 202 – 204) 145 Omnidirectional Antenna Vertical Polarization VPol Omni 870–960 360° 11dBi V 736347 Type No. 870 – 960 MHz Vertical 11 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 3033 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 870 – 960 7° 3 dB 10 0 Vertical Pattern Mechanical specifications 150 230 um maximtop mast Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8 kg 51 mm 210 N (at 150 km/h) 200 km/h 3316 x 148 x 112 mm 3033 mm 104 146 Brackets for side mounting (see page 202 – 204) Omnidirectional Antenna Vertical Polarization Fixed Electrical Downtilt 870 – 960 V 5° VPol Omni 870–960 360° 10.5dBi 5°T Frequency range Polarization Gain Electrical tilt Impedance VSWR Intermodulation IM3 Max. power 870 – 960 MHz Vertical 10.5 dBi 5°, fixed 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 2954 mm 736349 Type No. 7° 3 dB 10 0 Vertical Pattern 5° electrical downtilt Mechanical specifications 150 230 um maximtop mast Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8 kg 51 mm 210 N (at 150 km/h) 200 km/h 3316 x 148 x 112 mm 2954 mm 104 Brackets for side mounting (see page 202 – 204) 147 Dual-band Omni Antenna Vertical Polarization 870 – 960 790 – 862 V V VPol Omni 870–960/790–862 360°/360° 9/8dBi 80010747 Type No. Top system: Bottom system: 870 – 960 MHz 790 – 862 MHz Vertical Vertical 9 dBi 8 dBi Horizontal: Omni Horizontal: Omni Vertical: 11° Vertical: 16° > 30 dB 50 Ω < 1.5 < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 150 W 100 W (at 50 °C ambient temperature) Polarization Gain Half-power beam width Isolation, between ports Impedance VSWR Intermodulation IM3 Max. power per input Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductors of both systems are coupled capacitively. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 3 240 10 870–960 VPol 790–862 VPol 7-16 7-16 10 4 dB 10 16° 3 dB 11° 790–862 maximum mast top 150 40 870–960 3237 mm Frequency range 0 0 Vertical Pattern Vertical Pattern 123 Mechanical specifications 240 maximum mast top 150 40 85 48 Bottom view 870–960 MHz top system 790–862 MHz bottom system Input Connector position Weight Wind load Max. wind velocity Packing size Height Radome diameter 2 x 7-16 female Bottom 8 kg 230 N (at 150 km/h) 180 km/h 3516 x 148 x 112 mm 3237 mm 51 mm 10 4 Layout of interface 148 Brackets for side mounting (see page 202 – 204) 123 Dual-band Omni Antenna Vertical Polarization 870 – 960 1920 – 2170 V V VPol Omni 870–960/1920–2170 360°/360° 9/10dBi 80010274 Type No. Top system: Bottom system: 870 – 960 MHz 1920 – 2170 MHz Vertical Vertical 9 dBi 10 dBi Horizontal: Omni Horizontal: Omni Vertical: 11° Vertical: 9° > 30 dB 50 Ω < 1.5 < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 150 W 100 W (at 50 °C ambient temperature) Polarization Gain Half-power beam width Isolation, between ports Impedance VSWR Intermodulation IM3 Max. power per input Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductors of both systems are coupled capacitively. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 3 240 10 dB 10 9° 3 0 870–960 VPol 1920 –2170 VPol 7-16 7-16 10 4 dB 11° 1920 –2170 maximum mast top 150 40 870–960 3033 mm Frequency range 0 Vertical Pattern Vertical Pattern 123 Mechanical specifications 240 maximum mast top 150 40 85 48 Bottom view 870–960 MHz top system 1920–2170 MHz bottom system Input Connector position Weight Wind load Max. wind velocity Packing size Height Radome diameter 2 x 7-16 female Bottom 8 kg 230 N (at 150 km/h) 200 km/h 3380 x 148 x 112 mm 3033 mm 51 mm 10 4 Layout of interface Brackets for side mounting (see page 202 – 204) 123 149 Multi-band Omni Antenna 870 – 960 1710–1880 1920 – 2170 V V Vertical Polarization VVPol Omni 870–960/1710–1880/1920-2170 360°/360° 2/2dBi 80010111 Type No. Polarization Gain Isolation, between ports Impedance VSWR Intermodulation IM3 Max. power per input 493 mm Top system: Bottom system: 870 – 960 MHz 1920 – 2170 MHz 1710 – 1880 MHz Vertical Vertical 2 dBi 2 dBi > 25 dB > 25 dB 50 Ω 50 Ω < 1.5 < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 50 W (at 50 °C ambient temperature) Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Mounting: The antenna can be attached laterally at the tip of a tubular mast of 40 – 70 mm diameter with a mounting clamp supplied with the antenna. The connecting cables (not supplied) run outside the mast. Excellent grounding: The metal parts of the antenna and the mounting kit (exclusive the inner conductor of the upper unit) are DC grounded. 130 mm Frequency range 78° 3 1920–2170 Bottom N N dB 10 870– 960 1710 –1880 Top 0 Vertical Pattern Mechanical specifications VPol VPol 806–960 1710–1880 bottom system top system Input Connector position Weight Wind load Max. wind velocity Packing size Height Radome diameter 1920–2170 Layout of interface 2 x N female Bottom 0.85 kg 30 N (at 150 km/h) 200 km/h 665 x 112 x 97 mm 493 mm 30 mm Bottom view 150 Brackets for side mounting (see page 204) Omnidirectional Antenna Vertical Polarization VPol Omni 1710–1880 360° 11dBi Type No. V 738187 1710 – 1880 MHz Vertical 11 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 1568 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 1710 – 1880 7° 3 dB 10 0 Vertical Pattern Mechanical specifications 150 230 um maximtop mast Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 5.5 kg 51 mm 130 N (at 150 km/h) 200 km/h 1846 x 148 x 112 mm 1568 mm 104 Brackets for side mounting (see page 202 – 204) 151 Omnidirectional Antenna Vertical Polarization VPol Omni 1920–2170 360° 11dBi Type No. V 741790 1920 – 2170 MHz Vertical 11 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 150 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 1387 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 1920 – 2170 7° 3 dB 10 0 Vertical Pattern Mechanical specifications 130 um maximtop mast 104 152 Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 5 kg 51 mm 120 N (at 150 km/h) 200 km/h 1570 x 148 x 112 mm 1387 mm Brackets for side mounting (see page 204) Omnidirectional Antenna Vertical Polarization 2500 – 2700 V VPol Omni 2500–2700 360° 11dBi 0°T 80010442 Type No. 2500 – 2700 MHz Vertical 11 dBi 50 Ω < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 200 W (at 50 °C ambient temperature) Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50 – 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled. Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the requirements of lightning protection class II. Grounding cross-section: 22 mm2 copper. 1132 mm Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power 7° 3 dB 10 0 Vertical Pattern Mechanical specifications 130 um maximtop mast 104 Brackets for side mounting (see page 204) Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 4.5 kg 51 mm 110 N (at 150 km/h) 200 km/h 1232 x 148 x 112 mm 1132 mm 153 Omni Slimpole Antenna Dual Polarization 1710 – 2690 X XPol Omni Slimpole 1710–2690 360° 5dBi 80010126 Type No. Frequency range Polarization Gain Horizontal Pattern: Half-power beam width Deviation from circularity Vertical Pattern: Half-power beam width Electrical tilt 1710 – 1990 MHz +45°, –45° 2 x 5 dBi 1710 – 2690 1920 – 2170 MHz 2170 – 2490 MHz +45°, –45° +45°, –45° 2 x 5 dBi 2 x 5 dBi Omni ±1 dB Omni ± 1 dB 42° 40° Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power per input 0°, fixed 2490 – 2690 MHz +45°, –45° 2 x 5 dBi Omni ±1.5 dB Omni ±1.5 dB 36° 33° 50 Ω < 1.5 > 30 dB < –150 dBc (2 x 43 dBm carrier) 100 W (at 50 °C ambient temperature) 1710 – 2690 MHz: +45°/–45° Polarization 3 dB 10 Mechanical specifications Input Connector position Weight Wind load Max. wind velocity Mechanical interface 0 Horizontal Pattern 42° Packing size Height / diameter 3 dB 10 0 Vertical Pattern 0° electrical downtilt 154 2 x N-connector female Bottom Approx. 2.3 kg 50 N (at 150 km/h) 200 km/h Flange connection 8 x M6 at a graduated diameter of 136 mm (for further details see application note) 800 x 200 x 200 mm 694 / 100 mm Summary – Indoor Antennas VPol, VXPol, VHPol 790…6000 MHz Vertical Polarization Indoor – Directional Type VPol BiDir 65° VVPol Indoor 90° C Type No. Frequency range Connector female Page 5dBi 738446 790–960/1710–2170 N 134 7dBi 80010465 790–960/1710–2700 N 156 790–960/1710–2700 2xN 157 Indoor – Directional Dual Polarization VXPol Indoor 90° C 7dBi 80010677 Indoor – Multi-band Omnidirectional VPol Indoor 360° 2dBi 80010748 876–960/1710–2700 N 158 VPol Indoor 360° 2dBi 80010749 876–960/1710–2700 N 159 VPol Indoor 360° 2dBi 80010249 790–960/1425–3800/5150–6000 N 160 VPol Indoor 360° 2dBi 741573 1710–2700 N 161 VPol Indoor 360° 2dBi 80010430 1710–6000 N 162 Indoor – Omnidirectional Dual Polarization VHPol Indoor 360° 2dBi 80010709 790–960/1710–2700/2500–2700 2xN 163 VHPol Indoor 360° 2dBi 80010710 790–960/1710–2700/1710–2700 2xN 164 870–960 N 140 Indoor / Outdoor – Single-band VPol Omni 360° 2dBi 738450 Indoor / Outdoor – Dual-band Multi-band VPol Omni 360° 2dBi 80010431 1710–2700 N 165 VPol Omni 360° 2dBi 80010847 790–960/1710–2700 N 166 C = integrated Combiner New or changed product 155 Indoor Multi-band Directional Antenna Vertical Polarization Half-power Beam Width Integrated Combiner 790 – 960 1710–2700 V V 90° 90° C VVPol Indoor 790–960/1710–2700 C 90° 7dBi 80010465 Frequency range Polarization Gain Half-power beam width Impedance VSWR Max. power Input Protection class Weight Packing size Height/width/depth Material: 790 – 960 MHz / 1710 – 2700 MHz Vertical Approx. 7 dBi Horizontal: Approx. 90° 50 Ω 790 – 806 MHz: < 2.2 806 – 960 MHz: < 2.0 1710 – 2700 MHz: < 2.0 50 W (at 50 °C ambient temperature) Cable RG 223/CU of 1m length, white, with N female connector IP 30 500 g 363 x 152 x 62 mm 231 / 140 / 50 mm Reflector: Aluminum. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Mounting: Two holes of 6 mm diameter in the mounting plate. Screws are not supplied. Avoid stressing the cable. No stress on the hexagonal crimp. Minimum cable bending radius: 30 mm without tensile load. Grounding: All metal parts inclusive the inner conductor are DC grounded. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (694 – 2700 MHz). 1710–2700 VPol 790–960 VPol C N 90° 10 3 dB Type No. 0 Horizontal Pattern Mounting: Mount the attachment plate to the wall using two screws of 4 mm diameter in the position as indicated. 156 Align the antenna over the attachment plate. Pull the antenna to the stop. Indoor Multi-band Directional Antenna Vertical / Dual Polarization Half-power Beam Width Integrated Combiner 790 – 960 1710–2700 1710–2700 V X (–45°) X (+45°) 90° 90° 90° C VXPol Indoor 790–960/1710–2700 C 90° 7dBi 80010677 Type No. Protection class Weight Packing size Height/width/depth Material: Mounting: Available accessories: 790 – 960 MHz 1710 – 2700 MHz Vertical +45°, –45° Approx. 7 dBi Approx. 2 x 7 dBi Horizontal: Approx. 90° 50 Ω < 2.0 > 25 dB < –140 dBc (2 x 40 dBm carrier) 50 W (at 50 °C ambient temperature) 2x Cable RG 223/CU of 1m length, white, with N female connector IP 30 600 g 363 x 152 x 62 mm 232 / 140 / 50 mm Reflector: Aluminum. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting plates: Stainless steel. 1710–2700 XPol –45° 790–960 VPol C N N Position: Wall and ceiling possible. Two holes of 6 mm diameter in the mounting plate. Screws are not supplied. Avoid stressing the cable. No stress on the hexagonal crimp. Minimum cable bending radius: 30 mm without tensile load. Cable must be fixed. Broadband power splitters and tappers (694 – 2700 MHz). 1710–2700 XPol +45° 90° 10 3 dB Frequency range Polarization Gain Half-power beam width Impedance VSWR Isolation, between ports Intermodulation IM3 Max. power Input 0 Horizontal Pattern Mounting: Mount the attachment plate to the wall using two screws of 4 mm diameter in the position as indicated. Align the antenna over the attachment plate. Pull the antenna to the stop. 157 Indoor Multi-band Omni Antenna Vertical Polarization l 876–960 1710–2700 V The antenna needs no additional groundplane. VPol Indoor 876–960/1710–2700 360° 2dBi 80010748 Type No. Frequency range 876 – 960 MHz 1710 – 2700 MHz Vertical 2 dBi 50 Ω 876 – 890 MHz: < 2.0 890 – 960 MHz: < 1.7 1710 – 2170 MHz: < 1.6 2170 – 2700 MHz: < 2.0 < –140 dBc (2 x 40 dBm carrier) 50 W (at 50 °C ambient temperature) 1 x N female IP 30 300 g 210 mm 78 mm (without connector) Polarization Gain Impedance VSWR Intermodulation IM3 Max. power Input Protection class Weight Diameter Height Material: Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Grounding: All metal parts including the inner conductor are DC grounded. Available accessories: Broadband power splitters and tappers (694 – 2700 MHz). ∅ 210 mm min. dia. 35 mm 3 holes dia. 5 mm dia. 160 mm N connector, female 13 mm 158 Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. Indoor Multi-band Omni Antenna Vertical Polarization l 876–960 1710–2700 V The antenna needs no additional groundplane. VPol Indoor 876–960/1710–2700 360° 2dBi 80010749 Type No. Frequency range 876 – 960 MHz 1710 – 2700 MHz Vertical 2 dBi 50 Ω 876 – 890 MHz: < 2.0 890 – 960 MHz: < 1.7 1710 – 2170 MHz: < 1.6 2170 – 2700 MHz: < 2.0 < –140 dBc (2 x 40 dBm carrier) 50 W (at 50 °C ambient temperature) 1 x N female IP 30 340 g 215 mm 85 mm (without connector) Polarization Gain Impedance VSWR Intermodulation IM3 Max. power Input Protection class Weight Diameter Height Material: Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Grounding: All metal parts including the inner conductor are DC grounded. Available accessories: Broadband power splitters and tappers (694 – 2700 MHz). ∅ 215 mm min. dia. 35 mm 3 holes dia. 5 mm dia. 160 mm N connector, female 13 mm Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. 159 Indoor Multi-band Omni Antenna Vertical Polarization 790–960 1425 – 3800 5150 – 6000 V he antenna can be operated in all frequency ranges T simultaneously. l The antenna needs no additional groundplane. l VPol Indoor 790–960/1425–3800/5150–6000 360° 2dBi 80010249 Type No. Frequency range 790 – 960 MHz 1425 – 3800 MHz 5150 – 6000 MHz Vertical ≈ 2 dBi 50 Ω 790 – 806 MHz: < 1.7 806 – 960 MHz: < 1.5 1425 – 1710 MHz: < 2.0 1710 – 2200 MHz: < 1.4 2200 – 3800 MHz: < 1.6 5150 – 5300 MHz: < 2.4 5300 – 6000 MHz: < 2.0 < –140 dBc (2 x 40 dBm carrier) 50 W (at 50 °C ambient temperature) 1 x N female IP 30 466 g 277 x 277 x 169 mm 258 mm 94 mm (without connector) Polarization Gain Impedance VSWR Intermodulation IM3 Max. power Input Protection class Weight Packing size Diameter Height Material: Reflector: Aluminum. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (694 – 2700 MHz). ∅ 258 mm min. dia. 35 mm dia. 160 mm 3 holes dia. 5 mm N connector, female Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. 160 Indoor Omnidirectional Antenna Vertical Polarization 1710 – 2700 V he antenna can be operated in the total frequency range T simultaneously. l The antenna needs no additional groundplane. l VPol Indoor 1710–2700 360° 2dBi Type No. Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power Input Protection class Weight Diameter Height 741573 ∅ 100 mm 1710 – 2700 MHz Vertical 2 dBi 50 Ω 1710 – 1880 MHz: < 1.6 1850 – 1990 MHz: < 1.6 1920 – 2170 MHz: < 1.6 2170 – 2500 MHz: < 2.0 2500 – 2700 MHz: < 2.2 < –140 dBc (2 x 40 dBm carrier) 50 W (at 50 °C ambient temperature) 1 x N female IP 30 150 g 100 mm 50 mm (without connector) Material: Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Holes in the base enable a mounting on the ceiling. Screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Grounding: All metal parts including the inner conductor are DC grounded. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (694 – 2700 MHz). min. dia. 35 mm 80 mm 2 holes dia. 5 mm N connector, female 12.9 mm Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. 161 Indoor Omnidirectional Antenna Vertical Polarization 1710 – 6000 V he antenna can be operated in all frequency ranges T simultaneously. l The antenna needs no additional groundplane. l VPol Indoor 1710–6000 360° 2dBi Type No. Frequency range Polarization Gain Impedance VSWR Intermodulation IM3 Max. power Input Protection class Weight Diameter Height 80010430 ∅ 138 mm 1710 – 6000 MHz Vertical 2 dBi 50 Ω < 1.5 < –140 dBc (2 x 40 dBm carrier) 50 W (at 50 °C ambient temperature) 1 x N female IP 30 133 g 138 mm 56 mm (without connector) Material: Base: Aluminum. Protective housing: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Holes in the base enable a mounting on the ceiling. Screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (694 – 2700 MHz). min. dia. 35 mm 2 holes dia. 5 mm N connector, female dia. 88 mm Clip the protective housing into position after the antenna has been mounted with the help of two supplied screws. 162 Indoor Multi-band Omni Antenna Dual Polarization 790–960 1710 – 2700 2500 – 2700 V H he antenna can be operated in all frequency ranges T simultaneously. l The antenna needs no additional groundplane. l VHPol Indoor 790 – 960/1710–2700/2500–2700 360° 2dBi 80010709 Type No. Frequency range 790 – 960 MHz 1710 – 2700 MHz Vertical Polarization Gain Impedance VSWR 2500 – 2700 MHz Horizontal ~ 2 dBi 50 Ω 790 – 960 MHz: 2500 – 2700 MHz: < 2.0 < 2.0 1710 – 2700 MHz: < 2.0 > 30 dB < –140 dBc (2 x 40 dBm carrier) 50 W ( at 50 °C ambient temperature) 2 x N female IP 30 Approx. 500 g 277 x 277 x 169 mm 258 mm 94 mm (without connector) Isolation Intermodulation IM3 Max. power Input Protection class Weight Packing size Diameter Height Material: Reflector: Aluminum.Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connectors a hole in the ceiling is required. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (694 – 2700 MHz). 790–960 1710 –2700 VPol 2500 –2700 HPol N N min. Ø 65 mm 30 mm dia. 160 mm 3 holes dia. 5 mm N connector, female Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. 163 Indoor Multi-band Omni Antenna Dual Polarization 790–960 1710 – 2700 1710 – 2700 V H he antenna can be operated in all frequency ranges T simultaneously. l The antenna needs no additional groundplane. l VHPol Indoor 790–960/1710–2700/1710–2700 360° 2dBi 80010710 Type No. Frequency range 790 – 960 MHz 1710 – 2700 MHz Vertical Polarization Gain Impedance VSWR Isolation Intermodulation IM3 Max. power Input Protection class Weight Packing size Diameter Height 1710 – 2700 MHz Horizontal ~ 2 dBi 50 Ω 790 – 960 MHz: 1710 – 2700 MHz: < 2.0 < 2.0 1710 – 2700 MHz: < 2.0 > 30 dB < –140 dBc (2 x 40 dBm carrier) 50 W ( at 50 °C ambient temperature) 2 x N female IP 30 Approx. 1 kg 400 x 400 x 200 mm 380 mm 118 mm (without connector) Material: Reflector: Aluminum. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connectors a hole in the ceiling is required. Available accessories: Broadband power splitters (694 – 3800 MHz) and tappers (694 – 2700 MHz). 164 1710 –2700 HPol N N min. Ø 65 mm 30 mm 3 holes dia.5 mm dia. 312 mm N connector, female 790–960 1710 –2700 VPol Clip the protective housing into position after the antenna has been mounted with the help of the three supplied screws. Omnidirectional Antenna Vertical Polarization Indoor and outdoor use Type No. Input Connector position Frequency range VSWR Gain Impedance Intermodulation IM3 Polarization Max. power Weight Radome diameter Height V 80010431 N female Bottom or top 1710 – 2700 MHz < 1.8 2 dBi 50 Ω < –150 dBc (2 x 43 dBm carrier) Vertical 50 W (at 50 °C ambient temperature) 150 g 20 mm 115 mm Material: Radiator: Brass. Radome: Fiberglass, colour: White. Mounting: One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. Grounding: All metal parts of the antenna and the mounting kit are DC grounded. The inner conductor is not DC grounded. 115 mm VPol Omni 1710–2700 360° 2dBi 1710 – 2700 78° 3 dB 10 0 Vertical Pattern 165 Dual-band Omni Antenna Vertical Polarization Indoor and outdoor use 790 – 960/1710 – 2700 V VPol Omni 790–960/1710–2700 360° 2dBi Input Connector position Frequency range VSWR Gain Impedance Intermodulation IM3 Polarization Max. power Weight Wind load Radome diameter Height 1 x N female Bottom or top 790 – 960 MHz / 1710 – 2700 MHz < 2.0 2 dBi 50 Ω < –150 dBc (2 x 43 dBm carrier) Vertical 50 W (at 50 °C ambient temperature) 200 g 6 N (at 150 km/h) 30 mm 194 mm Material: Radiator: Brass. Radome: Fiberglass, colour: White. Mounting: One hole mounting (16 mm diameter) to surfaces of max. 10 mm thickness. 78° 3 dB 10 0 Vertical Pattern 166 194 mm 80010847 Type No. Summary – Remote Electrical Tilt (RET) Type Type No. Page Kathrein’s Remote Electrical Tilt System General information Data sheets of RET components 168 Slimline Remote Control Unit (RCU) 86010148 170 Antenna Line Configurator (ALC) 86010156 171 86010006 / 86010026 172 Portable Control Adapter (PCA) 86010046 173 Power Supply and Signal Cable 86010007, ... 174 Torque Screwdriver 85010080 174 DC Power and Signal Splitter 86010002 175 Lightning Protection Device 86010030 176 Earthing Clamp 86010031 177 Smart Bias Tee 78211053 / ..54 / ..55 / ..56 324 78211063 / ..64 / ..65 / ..66 324 Central Control Unit (CCU) for indoor use New or changed product 167 Kathrein’s Remote Electrical Tilt System The answer to all current and future network demands Network planning is becoming ever more complicated, especially with the advent of 3G and/or 4G (LTE). The challenge for wireless network operators is to balance coverage, capacity, call quality and costs in order to gain maximum revenue from their network. Each of the above factors affects the others and so network engineers use many different techniques However, with Kathrein’s Remote Electrical Tilt unit engineers can make the necessary adjustments with out shutting down the whole system! Further advantages of using Kathrein’s Remote Electrical Tilt (RET) system: – No need for specialized teams trained in altitude work or with special safety skills – Limited site access and/or time restrictions are not so important – No special platforms or other means of access to the antenna are required – Adjustments can be made and the relevant measurements performed speedily – Network alterations can be carried out irrespective of weather conditions – No reduction in coverage – cells remain fully operational whilst changes are being made – Operators estimate that approx. 20% of UMTS equipment can be saved by using such a RET system. 168 for establishing the right balance they are trying to achieve. One of these methods is adjusting the antenna’s downtilt. Here, the engineer must take into consideration certain facts, such as the weather, access to the cell site, availability of specialized installation teams and special equipment etc. Moreover, such an antenna adjustment can typically take several hours to perform. Since the cell site is usually switched off for safety reasons during such an adjustment, this results in lost calls and therefore revenue whilst these changes are being made. Consequently, operators tend to make fewer adjustments and so networks are often left operating unoptimized, which also eventually results in lost revenue for the operators. Kathrein’s Remote Electrical Tilt System RET components Slimline RCU (Remote Control Unit) Control Cable Lightning Protection Device Kathrein’s overall RET system works in accordance with the AISG (Antenna Interface Stan dards Group) standard and 3GPP (3rd Generation Partner ship Project). CCU (Central Control Unit) ALC (Antenna Line Configurator) Earthing Clamp Optional: (for further infor mation see filter part) Smart Bias Tee stem ET sy R f o s e etail re For d please se m brochu e t s y ET s in’s R athre K Edition 2012 KATHREIN’s Remote Electrical Tilt System Overview of related products, installation and control possibilities 99811878_Remote.indd 1 PCA (Portable Control Adapter) AISG-DTMA (Double Tower Mounted Amplifier) DC Power and Signal Splitter Smart Plex® 16.05.2012 11:25:32 169 Remote Control Unit (RCU) Remote Control Unit (RCU) for Kathrein base station antennas with adjustable electrical downtilt and appropriate mechanical interface. l l Compliant to AISG 1.1 and 3GPP/AISG 2.0 Compact size Hardware interfaces Adjustment time (full range) Adjustment cycles Temperature range Protection class Lightning protection Housing material Weight Packing size Dimensions (H x W x D) 1) l Daisy Chain feasibility Suitable for operation under outdoor condition 86010148 Type No. Protocols Logical interface ex factory 1) Input voltage range Power consumption Connectors 2) l compliant to AISG 1.1 and 3GPP/AISG 2.0 3GPP/AISG 2.0 10 ... 30 V (pin 1, pin 6) < 1 W (stand by); < 10 W (motor activated) 2 x 8 pin connector according to IEC 60130-9; according to AISG Daisy chain in: male; Daisy chain out: female RS 485A/B (pin 5, pin 3); power supply (pin 1, pin 6); DC return (pin 7); according to AISG / 3GPP 40 sec (typically, depending on antenna type) > 50,000 –40 °C … +60 °C IP 24 AISG interface (each pin) 2.5 kA (10/350 µs) 8 kA (8/20 µs) Profile: Aluminum anodized; cover: Aluminum die cast coated 455 g (0.99 lbs) 245 x 93 x 102 mm, (9.6 x 3.6 x 4 inches) 177.5 x 59.5 x 49.5 mm, (7.0 x 2.3 x 1.9 inches) he protocol of the logical interface can be switched from 3GPP/AISG 2.0 AISG 1.1 to with a vendor T specific command. Start-up operation of the RCU is only possible in a RET system supporting 3GPP/ AISG 2.0! The protocol can also be changed as follows: 3GPP to AISG 1.1: Enter “AISG1” into the additional data field “Installer’s ID” and perform a layer 2 reset or a power reset. AISG 1.1 to 3 GPP: Enter “3GPP” into the additional data filed “Installer’s ID” and perform a layer 7 reset or a power reset. After switching the protocol any other information can be entered into the “Installer’s ID” field. Please note: If the Primary of the RET system doesn’t support the standard of the ‘logical interface ex factory’, the RCU must be switched to the appropriate standard of the Primary before installation. Please contact Kathrein for further information. Daisy chain out (female) he tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). T The connector should be tightened by hand only! Standards: EN 60950-1 (Safety) EN 60950-22 (Safety – Equipment installed outdoor) EN 55022 (Emission) EN 55024 (Immunity) ETS 300019-1-4 (Environmental) UL 60950-1; 1st edition Certification: CE, FCC Scope of supply: Remote Control Unit Assembly paste 8 mm (0.31ʺ) 170 49.5 mm (1.95ʺ) 28.5 mm (1.1ʺ) Ø 46 mm (Ø 1.8ʺ) M42x1.5 173.6 mm (6.8ʺ) Bottom view of RCU 33.2 mm (1.27ʺ) 59.5 mm (2.34ʺ) 2) Daisy chain in (male) Antenna Line Configurator (ALC) For Antenna Line Devices (ALD) Antenna Line Configurator Type No. Connector* to RCU/TMA Input voltage of ALC Display Tiltsensor Output voltage to RCU’s/ TMA’s Output power (power supply to RCU’s/ TMA’s) Current monitoring measurement level Over-current protection Interface to RCU/TMA Protocol to RCU/TMA Interface Max. number of RCU’s/TMA’s Max. length of control cable 86010156 1 x 8-pin connector according to IEC 60130-9, female, conforming to AISG RF-connector (SMB male) 20 – 30 V DC Touchscreen, sunlight visible Measuring range ±80°, accuracy ±1° AISG female pin 6 (24 V DC): 20–30 V DC AISG female pin 1 (12 V DC): 10–15 V DC 10–30 V DC ** RF male (at 24 V DC): RF male (at 12 V DC): 10–15 V DC ** AISG female pin 6 (24 V DC) without load on pin 1 (12 V DC) and on RF-plug: ≤ 15 W AISG female Pin 1 (12 V DC) with max. 7.5 W load on pin 6 (24 V DC) and/or on RF plug: ≤ 7.5 W Per branch (12 V, 24 V, RF): 10–1500 mA Per branch (12 V, 24 V, RF): < 1500 mA RS 485 / power supply / RF connector (SMB male) HDLC hex-coded command set, conforming to AISG 1.1 and 3GPP / AISG 2.0 W-LAN (802.11n), USB (1.1 / 2.0) 9/1 pcs., depending on system configuration and length of control cable 200 m / 9 RCU’s (in daisy chain configuration) 150 m / 6 RCU’s (in splitter configuration) Internal memory 380 MB Weight 1 kg Protection class IP 54 Temperature range (operating) –20 ... +55 °C ambient temperature Temperature range (charging) 0 ... +40 °C ambient temperature Dimensions (H x W x D) 265 x 102 x 37 mm Packing size 400 x 280 x 85 mm Power supply LiPo-battery (14.8 V, > 2000 mAh) * T ightening torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). The connector should be tightened by hand only! ** Switchable with software Certificate: CE FCC part 15 class B UL (for external power adapter) Standards: EN 60950-22 EN 55022 EN 55024 Scope of supply: ALC Charging device (can also be used as external power supply) USB cable RET cable HF cable (SMB / 7-16) Quick Guide Transport case Optional: Car-Adapter (Type No. 86010158) 171 Central Control Unit (CCU) For Remote Electrical Tilt (RET) and Tower Mounted Amplifier (TMA) Control For indoor use Central Control Unit 86010006 Type No. Antenna Antenna Interface to RCU and TMA Protocol to RCU and TMA Interface to BTS Protocols to BTS Alarm interface to BTS Max. number of RCU’s and/or TMA’s Max. length of control cable Temperature range Packing size Dimensions (h / w / d) RS 485 / power supply HDLC hex-coded command set, acc. to AISG Ethernet (10 Base-T) and RS 232 TCP/IP, PPP, HTTP/HTML, UDP, DHCP, FTP, SNMP, ICMP/PING 8 x open collector output, user programmable Up to 27 RCU’s in daisy chain and up to 6 DTMA’s; depending on cable configuration and max. power 200 m (9 RCU’s in daisy chain configuration) –25 °C ... +55 °C ambient temperature 597 mm x 367 mm x 148 mm 19ʺ 1 HU* (43.6 mm / 483 mm / 250 mm) Antenna Total output power Antenna Power supply to RCU 86010026 3 x 8 pin connector acc. to IEC 60130-9, female, acc. to AISG DC: –48 V / max. 1.7 A DC: –48 V / max. 1.7 A AC: 100 … 240 V / 50 ... 60 Hz / max. 1.6 A 3 x +29 V DC / max. 1.7 A (in total) 3 x +13 V DC / max. 3.8 A (in total) Max. 50 W Antenna Connectors1) to RCU Power supply from BTS * HU = Height Unit 1) The tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand tightened’). The connector should be tightened by hand only. Standards: RCU RCU Certifications: Smart Bias Tee CCU Interfaces Examples of CCU – RCU connections To Splitter or to RET/TMA via Smart Bias Tee 3 x RS 485 3 x 13 V / 3 x 29 V 172 GND AC: 100 – 240 V max. 1.6 A (only 860 10006) Alarm Interface DC: –48 V max. 1.7 A 8 x Open Collector Ethernet RS 232 CCU Central Control Unit Network Interfaces RCU CE, FCC part 15 class B; UL RS 485 CCU RET Manual DC Cable Splitter AC Power Cords for 1:3 USA, UK and Germany Ethernet cable, crossed Scope of supply: Smart TMA Bias Tee Smart Bias Tee EN 60950-1 EN 55022 EN 55024 RCU RCU UL 60950-1, 1st edition Portable Control Adapter (PCA) For Remote Control Unit (RCU) For Tower Mounted Amplifier (TMA) Portable Control Adapter Type No. Connector * to RCU/TMA Input voltage of PCA Output voltage to RCU’s/ TMA’s Output power (power supply to RCU’s/ TMA’s) Current monitoring measurement level Over-current protection Interface to RCU/TMA Protocol to RCU/TMA Interface to PC Max. number of RCU’s/TMA’s Max. length of control cable Weight Temperature range Height x width x depth External power supply ** * 86010046 1 x 8-pin connector according to IEC 60130-9, female, conforming to AISG RF-connector (SMB male) 24 V DC AISG female pin 6 (24 V DC): 24 V DC ±10% AISG female pin 1 (12 V DC): 14 V DC ±7% RF male (at 24 V DC): 24 V DC ±10% *** RF male (at 12 V DC): 14 V DC ±7% *** AISG female pin 6 (24 V DC) without load on pin 1 (12 V DC) and on RF-plug: ≤ 60 W AISG female Pin 1 (12 V DC) with max. 30 W load on pin 6 (24 V DC) and/or on RF plug: ≤ 30 W Per branch (12 V, 24 V, RF): 10 – 2500 mA Per branch (12 V, 24 V, RF): < 2500 mA RS 485 / power supply / RF connector (SMB male) HDLC hex-coded command set, conforming to AISG 1.1 and 3GPP / AISG 2.0 USB 1.1/2.0 27/3 pcs., depending on system configuration and length of control cable 200 m / 9 RCU’s (in daisy chain configuration) 150 m / 6 RCU’s (in splitter configuration) 535 g (incl. external power adapter) 0 ... +55 °C ambient temperature 40 mm x 95 mm x 160 mm Input: 90 – 264 V AC, 47 – 63 Hz 24 V DC / 3.0 A Tightening torque for fixing the connector must be 0.5 – 1.0 Nm (‘hand-tightened’). The connector should be tightened by hand only! ** If powered via AISG-interface, no external power supply is required. *** Switchable with software Certificate: CE FCC part 15 class B UL (for external power adapter) Standards: EN 60950-1 EN 55022 EN 55024 System requirements for PCA Software: Windows 2000; Windows XP, Vista, Win7 (32 bit version) Scope of supply: PCA External power supply (24 V DC / 70 W) USB cable AC power cable CD-ROM with PCA software, drivers and manual Installation guide 173 Connecting Cable For Remote Electrical Tilt (RET) System For indoor and outdoor use RET Cable for power supply and control Type No. Connectors Tightening torque for fixing the connectors Construction Rated current Temperature range Protection class Cable diameter Flammability Colour Minimum bending radius: 86010007 ... 2 x 8 pin connector according IEC 60130-9, female/male 0.5 – 1 Nm (The connector should be tightened by hand or by special torque scredriver) Screen 1x twisted pair 100 Ω/1 MHz 2x power supply, 1x ground AWM style 20317 I/II A/B + 20549 + 20233 4 A (power supply) (at 50 °C air temperature) –40 °C to +80 °C, (fixed position) IP 67 (connected) 8 mm VL 1581 VW-1 CSA FT 1 Black, similar to RAL 9005 One time 60 mm, several times 120 mm. The male and female connectors of all Kathrein RET products are compatible components which are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E. Control Cable Female Length Type No. 0.5 m 1m 2m 3m 5m 10 m 20 m 25 m 40 m 50 m 60 m 80 m 100 m 86010054 86010007 86010008 86010029 86010009 86010010 86010032 86010011 86010012 86010033 86010013 86010014 86010015 Optional: Torque screwdriver for AISG connecting cable (order no. 85010080). With the torque screwdriver, Kathrein connecting cables can be easily fixed with the recommended torque of 1 Nm. 174 7 3 5 8 2 Male 6 6 1 1 4 4 8 2 7 3 5 PIN assignment according AISG: 1 +13 V DC (+12 V DC nominal) 2 not connected 3 RS485 B 4 not connected 5 RS485 A 6 +29 V DC (+24 V DC nominal) 7 DC Return 8 not connected 7 3 Old style connector: Torque screwdriver not usable New style connector: Torque screwdriver usable DC-Power and Signal Splitter For Remote Electrical Tilt (RET) Indoor and Outdoor Use AISG compliant device for splitting of DC-power and control signals from one input to three outputs. 3-way Splitter for RET 86010002 Type No. Connectors1) Rated current (power supply) Max. voltage Protection class Weight Packing size Height/width/depth 1) 4 x 8 pin connector according IEC 60130-9, 1 x male, 3 x female 3 A (at 50 °C) 60 V IP 65 250 g 114 mm x 117 mm x 117 mm 91 mm / 103 mm / 72 mm he tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘handT tightened’). The connector should be thightened by hand only! Material: Connector plate: Aluminum. Cap: Plastic. Mounting: Mast mounting (50 – 145 mm diameter) by clamp. Wall mounting by screws (not supplied). Note: Connectors must be situated at the bottom. No inverted mounting possible. Scope of supply: 3-way Splitter Clamp (50...145 mm) 2 pins (power supply, max. 3 A) 6 pins (max. 0.1 A) Input Output 1 Output 2 Output 3 175 Lightning Protection Device (LPD) For Remote Electrical Tilt (RET) Indoor and Outdoor Use The device is designed for lightning protection of control cables carrying partial lightning currents up to 25 kA (shield) and 2.5 kA (inner conductor), according IEC 61643-1, IEC 61312-3. Each pin is protected individually. Lightning Protection Device for RET Type No. Connectors1) SPD-Type Max. impuls current Max. dynamic overvoltage at spark gap (1 kV/µs) Static overvoltage (100 V/s) Grounding Max. operation current Max. operation voltage Protection class Weight Packing size Height/width/depth 1) 86010030 2 x 8 pin connector according IEC 60130-9, input: male, output: female 8 x bipolar gas tube 25 kA (housing, shield) (10/350 µs) inner conductors: 2.5 kA/pin (10/350 µs) < 700 V < 100 V Via mounting plate / clamps at metallic surfaces or via separate cable, min. cross-section 5 mm2 Cu (screw M6) 4 A at 50 °C 60 V IP 55 250 g 114 mm x 117 mm x 117 mm 91 mm / 103 mm / 72 mm he tightning torque for fixing the connector must be 0.5 – 1.0 Nm (‘handT tightened’). The connector should be thightened by hand only! Material: Connector plate: Aluminum. Cap: Plastic. Mounting: Mast mounting (50 – 145 mm diameter) by clamp. Wall mounting by screws (not supplied). Note: No decoupling elements are integrated. The coordination with additional LPD’s (device input) should be checked according to IEC 61312. Grounding of the device via the mounting plate at metallic surfaces or via additional grounding cable (not included in the delivery extend). Connectors must be situated at the bottom. No inverted mounting possible. Important: A control cable with a minimum length of 2 meters is required between Lightning Protection Device and Central Control Unit at the BTS to achieve the required decoupling. Scope of supply: 176 Lightning Protection Device Clamp (50 ... 145 mm) Earthing Clamp For Power Supply and Control Cable For Remote Control Unit (RCU) The clamp is designed for lightning protection of control cables according to EN 50164-1 Earthing clamp for RCU power supply and signal cable 86010031 Type No. Max. lightning current Contact resistance Protection class Grounding Packing size Weight 20 kA (pulse 10/350 µsec) < 3 mΩ IP 68 Via stranded grounding wire, 16 mm2, length 0.5 m, one end terminated with cable eye (10 mm lug) Plastic bag: 210 mm x 210 mm 160 g Material: Body: Stainless steel with vulcanized EthylenePropylene-Caoutchouc Screw: Stainless steel Skin: Copper alloy Grounding wire: Copper Note: The earthing clamp is suitable only for the Ka threin Power Supply and Signal Cables, Type No. 860 10007 to 860 10015, 860 10029, 860 10032, 860 10033, 860 10054 to 860 10060 or shielded cables with – shield diameter 6.1 mm – jacket diameter 7.8 mm ±0.3 mm The kit contains: 1 x Grounding kit body incl. Butyl sealing rope covered with paper 1 x Screw M6 DIN 912 1 x Grounding wire Mounting instructions: This instruction is written for qualified and experienced personnel. Please read it carefully before starting work. Any liability or responsibility for the result of improper or unsafe installation is disclaimed! Attention! Install grounding kit only where the cable runs straight. Fig. 1a Preassembled grounding kit. Fig. 1b Clean the plastic jacket at the desired grounding point and cut out a strip of 15 mm with aid of a suitable stripping tool. Remove covering paper from Butyl sealing. Wrap the grounding kit body around the cable and align it. Tighten the screw (> 6 Nm) 177 178 Summary – Electrical Accessories 380...3800 MHz Splitters Type Type No. Frequency range Remark Max. Connector Page power female 2-way Splitter 380–3800 2-way Splitter 380–3800 86010130 86010131 380 – 3800 MHz Indoor/Outdoor 380 – 3800 MHz Indoor/Outdoor 200 W 700 W N 7-16 180 180 2-way Splitter 694–2700 3-way Splitter 694–2700 4-way Splitter 694–2700 86010017 86010018 86010019 694 – 2700 MHz 694 – 2700 MHz 694 – 2700 MHz Indoor Indoor Indoor 100 W 100 W 100 W N N N 181 181 181 2-way Splitter 694–3800 2-way Splitter 694–3800 3-way Splitter 694–3800 3-way Splitter 694–3800 4-way Splitter 694–3800 4-way Splitter 694–3800 86010100 86010101 86010102 86010103 86010104 86010105 694 – 3800 MHz 694 – 3800 MHz 694 – 3800 MHz 694 – 3800 MHz 694 – 3800 MHz 694 – 3800 MHz Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor Indoor/Outdoor 200 W 700 W 200 W 700 W 200 W 700 W N 7-16 N 7-16 N 7-16 182 182 182 182 182 182 2-way Tapper 694–2700 7.0/1.0 dB 2-way Tapper 694–2700 10.4/0.4 dB 2-way Tapper 694–2700 15.1/0.1 dB 86010136 86010137 86010138 694 – 2700 MHz 694 – 2700 MHz 694 – 2700 MHz Indoor Indoor Indoor 100 W 100 W 100 W N N N 183 183 183 2-way Tapper 694–2700 7.0/1.0 dB 2-way Tapper 694–2700 10.4/0.4 dB 2-way Tapper 694–2700 15.1/0.1 dB 86010150 86010151 86010152 694 – 2700 MHz Indoor/Outdoor 694 – 2700 MHz Indoor/Outdoor 694 – 2700 MHz Indoor/Outdoor 500 W 500 W 500 W 7-16 7-16 7-16 184 184 184 Indoor 100 W N 185 Indoor 100 W N 185 Tappers Continuously adjustable ratio 2-way Tapper 790–960/1710–2170 5.0–15.0dB 2-way Tapper 870–960/1710–2500 5.0–15.0dB K63236001 86010023 790 – 960 MHz 1710 – 2170 MHz 870 – 960 MHz 1710 – 2500 MHz Measurement Tools (from Schomandl) SWR Instrument FAT 2710N FIT-USB Frequency Time Standard FN-GPS / Taref3 / Taref30 Safe One Resonal RF Safety Monitor 186 186 186 186 179 Low-loss Power Splitters Multi-band 380 – 3800 For indoor and outdoor use. 2-way Splitter 380–3800 Type No. Connector (female) Max. power (at 50 °C ambient temperature) For connecting ... antennas Frequency range VSWR Intermodulation IM3 Impedance Insertion loss Weight Packing size 86010130 86010131 N 200 W 7-16 700 W 2 380 – 3800 MHz < 1.5 < –150 dBc (2 x 43 dBm carrier) 50 Ω < 0.05 dB 750 g 870 g 300 x 75 x 75 mm Material: Brass. Surface treatment: CuSnZn3 Mounting: Bracket for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately). DC capability: DC transmission between all terminations (suitable for remote power supply systems). Environmental conditions: ETS 300 019-1-4 class 4.1 E – Low temperature: –55 °C – High temperature (dry): +60 °C IP 65 14.5 86010131 86010131 15 SW 24 7 34 86010130 35 61 input 260 86010130 36 SW 24 11 54 input 13.5 263.5 Clamps (order separately) Type 736801 736802 736803 736804 736805 180 Description Remarks 1 clamp 1 clamp 1 clamp 1 clamp 1 clamp Mast: 34 – 60 mm diameter Mast: 60 – 80 mm diameter Mast: 80 – 100 mm diameter Mast: 100 – 120 mm diameter Mast: 120 – 140 mm diameter 736805 Low-loss Power Splitters Multi-band 694 – 2700 For indoor use. 2-way Splitter 694–2700 3-way Splitter 694–2700 4-way Splitter 694–2700 Type No. Frequency range For connecting ... antennas Insertion loss Impedance VSWR 694 – 894 MHz: 790 – 2500 MHz: 2500 – 2700 MHz: Intermodulation IM3 Max. power Connector Weight Profile cross-section Packing size Max. size 86010017 86010018 86010019 694 – 2700 MHz 3 < 0.05 dB 50 Ω < 1.5 < 1.5 < 1.25 < 1.25 < 2.0 < 2.0 < –150 dBc (2 x 43 dBm carrier) 100 W (at 50 °C ambient temperature) N female approx. 0.6 kg 25 x 25 mm 242 x 110 x 95 mm 204 / 63 / 44 mm 2 Material: Housing: Aluminum. Inner conductor: Brass. DC capability: DC transmission between all terminations (suitbale for remote power supply systems). Environmental conditions: IP 52 4 < 1.5 < 1.3 < 2.0 Input 86010019 181 Low-loss Power Splitters Multi-band 694 – 3800 For indoor and outdoor use. 2-way Splitter 694–3800 3-way Splitter 694–3800 4-way Splitter 694–3800 Type No. Connector (female) Max. power (at 50 °C ambient temperature) For connecting ... antennas Frequency range VSWR 86010100 86010101 86010102 86010103 86010104 86010105 N 200 W 7-16 700 W 2 Intermodulation IM3 Impedance Insertion loss Weight Packing size 750 g 870 g N 200 W Brass. Surface treatment: CuSnZn3 Mounting: Bracket for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately). DC capability: DC transmission between all terminations (suitable for remote power supply systems). Environmental conditions: ETS 300 019-1-4 class 4.1 E – Low temperature: –55 °C – High temperature (dry): +60 °C IP 65 7-16 700 W 4 775 g 960 g 86010105 15 SW 24 7 26 N 200 W 3 694 – 3800 MHz 694 – 894 MHz: < 1.32 790 – 3800 MHz: < 1.15 < –150 dBc (2 x 43 dBm carrier) 50 Ω < 0.05 dB 760 g 900 g 300 x 75 x 75 mm Material: 34 7-16 700 W 35 61 input 64.5 260 36 25 86010104 SW 24 86010105 54 input 86010104 263.5 63 Clamps (order separately) Type 736801 736802 736803 736804 736805 182 Description Remarks 1 clamp 1 clamp 1 clamp 1 clamp 1 clamp Mast: 34 – 60 mm diameter Mast: 60 – 80 mm diameter Mast: 80 – 100 mm diameter Mast: 100 – 120 mm diameter Mast: 120 – 140 mm diameter 736805 Low-loss Power Tappers Multi-band 694 – 2700 For indoor use. P1 2-way Tapper 694–2700 7.0 /1.0dB 2-way Tapper 694–2700 10.4/0.4dB 2-way Tapper 694–2700 15.1/0.1dB Type No. Frequency range Tap Loss Input ↔ P1 Input ↔ P2 For connecting ... antennas Insertion loss Impedance VSWR 86010136 86010137 86010138 – 1.0 dB – 7.0 dB Intermodulation IM3 Max. power Connector Weight Profile cross-section Packing size Max. size 694 – 2700 MHz P2 – 0.4 dB – 0.1 dB – 10.4 dB – 15.1 dB 2 < 0.05 dB 50 Ω 694 – 790 MHz: < 2.0 790 – 2500 MHz: < 1.5 2500 – 2700 MHz: < 2.0 < –150 dBc (2 x 43 dBm carrier) 100 W (at 50 °C ambient temperature) N female 500 g 25 x 25 mm 267 x 95 x 111 mm 244 / 64 / 25 mm Material: Housing: Aluminum. Inner conductor: Brass. DC capability: DC transmission only between input and port P1. P2 is coupled capacitively. Environmental conditions: IP 52 Input 86010138 183 Low-loss Power Tappers Multi-band 694 – 2700 For indoor and outdoor use. 2-way Tapper 694–2700 7.0 /1.0dB 2-way Tapper 694–2700 10.5/0.5dB 2-way Tapper 694–2700 15.3/0.3dB Type No. Frequency range Tap Loss Input ↔ P1 Input ↔ P2 For connecting ... antennas Insertion loss Impedance VSWR Intermodulation IM3 Max. power per input Connector Weight Packing size Max. size 86010150 –1.0 dB –7.0 dB 86010151 694 – 2700 MHz 86010152 –0.5 dB –0.3 dB –10.5 dB –15.3 dB 2 < 0.05 dB 50 Ω 694 – 2700 MHz: < 1.5 < –150 dBc ( 2 x 43 dBm carrier) 500 W (at 50 °C ambient temperature) 7-16 female Approx. 1.3 kg 310 x 93 x 112 mm 244 / 90 / 55 mm Material: Housing: Aluminum. Inner conductor: Brass. DC capability: DC transmission only between input and port P1. P2 is coupled capacitively. Mounting: Bracked for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately). Environmental conditions: P1 P2 Input 86010150 IP 65 Clamps (order separately) Type No. 734360 734361 734362 734363 734364 734365 184 Description Remarks 1 tension band 1 tension band 1 tension band 1 tension band 1 tension band 1 tension band Mast: 34 – 60 mm diameter Mast: 60 – 80 mm diameter Mast: 80 – 100 mm diameter Mast: 100 – 120 mm diameter Mast: 120 – 140 mm diameter Mast: 45 – 125 mm diameter 734364 Low-loss Power Tappers Multi-band Continuously Adjustable 790–960 / 1710–2170 870–960 / 1710–2500 5.0 – 15.0 dB For indoor use. P1 K63236001: 2-way Tapper 790–960/1710–2170 5.0–15.0dB 86010023: 2-way Tapper 870–960/1710–2500 5.0–15.0dB K63236001 Type No. Frequency range 86010023 790 – 960 MHz and 870 – 960 MHz and 1710 – 2170 MHz 1710 – 2500 MHz –5.0 dB to –15.0 dB Power ratio between outputs continuously adjustable (P2 ↔ P1) For connecting ... antennas 2 Insertion loss < 0.1 dB Impedance 50 Ω VSWR 790 – 824 MHz: < 2.1 < 1.7 824 – 960 MHz: < 1.7 1710 – 2170 MHz: < 1.7 Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier) Max. power 100 W (at 50 °C ambient temperature) Connector N female Weight 0.5 kg Profile cross-section 25 x 25 mm 277 x 111 x 40 mm Packing size 249 x 111 x 40 mm Max. size 235 / 100 / 25 mm 263 / 100 / 25 mm Material: Housing: Aluminum. Inner conductor: Brass. Adjustment mechanism: ASA. DC capability: DC transmission only between input and port P1. P2 is coupled capacitively. Environmental conditions: IP 52 P2 Blocking unit Input 86010023 Splitting table P2 / P1 [dB] Splitting ratio P1 / P2 –5 –6 –7 –8 –9 –10 –11 –12 –13 –14 –15 3.2 4 5 6.3 8 10 12.6 15.8 20 25.1 31.6 Splitting attenuation PInput / P1 [dB] PInput / P2 [dB] –1.2 –1.0 –0.8 –0.6 –0.5 –0.4 –0.3 –0.3 –0.2 –0.2 –0.1 –6.2 –7.0 –7.8 –8.6 –9.5 –10.4 –11.3 –12.3 –13.2 –14.2 –15.1 185 Measurement Tools SWR Instrument FAT 2710 • LCD Display works in direct sunlight and with backlight in dark areas. • Built-in synthesized RF sweeping source. • Measured results can stored for further analysing and documentation on internal and external storage media • Time stamp and operator ID is possible • All in one analysing for antenna tuning and control • FAT 2710 measures antenna, frequency, SWR and bandwidth by sweeping band of interest • A cost-effective SWR Analyzer covering all major Cellular and mobile radio communication bands • FAT 2710 gives you quick and reliable trouble-shooting FIT-USB Directional coupler available from 25…3000 MHz Power measurement from 0,1mW to 300W Simultaneous reading of power and antenna matching Measures average power or burst power Automatic identification of CW, GSM, TETRA and DMR Insertion loss max. 0,1 dB Directivity min. 30dB VSWR measurement 1,05…∞ Frequency Time Standard FN-GPS / Taref3 / Taref30 NTP server with web interface available User Clock (500kHz…2,4MHz) with 1Hz resolution available EU or US interface available Multiple output port version available, please ask for orde • Transmitter synchronization (DVB-T) • Head end synchronization (Dect) • Radio transmission internal and external storage media • Telecommunication systems (GSM,LTE) • PC - networks Safe One – Personal RF Safety Monitor Monitors RF fields Indicates RF pollution Alarm and Silent modes Broadband coverage General Safety According to WHO ICNIRP Alarm 2W/m2 or 10W/m2 186 Please contact for technical information and orders: SCHOMANDL-Vertriebs-GmbH Bahnhofstraße 108 · D-83224 Grassau/Germany · Telephone: 08641-403-140 · Telefax: 08641-403-264 e-mail: info@schomandl.de · Internet: http://www.schomandl.de Summary – Mechanical Accessories Clamps, Downtilt Kits ... Page Mounting Configurations 188 Dimensions of Panels 189 Colour Coding for Connectors on outdoor Base Station Antennas 190 Modified Product Line of Mounting Parts 191 Clamps Downtilt kit “L” Downtilt kit “L” and “M” Downtilt kit “H” Azimuth Adjustment Kits 3 Sector Clamps Offset 2x Panel Mounting Kit Tension Band 192 193 194 195 196 197 198 199 201 Side-mounting Clamp Omnis 202 Azimuth Adjustment Tool 205 The hereinafter referred to “wind load category L - M - H” correspond to the defined “category of mounting hardware” given in the respective data sheets. 187 Mounting Configurations Small Pipe Diameter Off-set Large Pipe Diameter Flat Surface Standard Downtilt Off-set Downtilt Azimuth 188 Dimensions of Panels Antenna dimensions and detailed connector position can be found on our current data sheets. Please refer to the information on our latest data sheets which are available on our homepage: www.kathrein.de – Base station system products – Product search An example is shown below of how the antenna dimensions are displayed on our data sheets: Front view Bottom view 64 46 49 108 A B C 167* 146* 9 72 60 167 184 261* * Dimensions refer to radome Adjustment mechanism with integrated scale 189 Colour Coding for Connectors on outdoor Base Station Antennas Frequency range (MHz) First coding Second coding Third coding Frequency range is not devided Frequency range is split into 2 bandwidths or 2 separate systems within same frequency range Frequency range is split into 3 bandwidths or 3 separate systems within same frequency range Broken line Dotted line Broken line Dotted line Broken line Dotted line Base colour Red Continuous line High-band 1710 ... 2200 Base colour Blue Continuous line incl. LTE 2.6 1710 ... 2690 Base colour Yellow Continuous line Dual-band antenna Low band 694 ... 960 Dual-band filterantenna // 2.6 GHz Side-by-side 900 // 900 MHz Standard Dual-band 800 MHz // 2.6 GHz Side-by-side 800 // 900 MHz Side-by-side 2.6 // 2.6 GHz not applicable Standard Dual-band 800 MHz // 2.6 GHz Combiner Version Dual-band 800 MHz // 2.6 GHz Quad-band antenna Triple-band antenna Filterantenna Triple-band 900 MHz // 2 // 2.6 GHz 190 Filterantenna Triple-band 800 // 900 MHz // 2 GHz Stacked Triple-band 900 MHz // 2.6 // 2.6 GHz no example available yet Filterantenna Quad-band 800 // 1800 MHz // 2 // 2.6 GHz not applicable no example available yet Quad-band 800 // 1800 MHz // 2 // 2.6 GHz Modified Product Line of Mounting Parts Type Clamp Windload Classification Pole Diameter in mm Type No. light / medium ∅ 28 – 64 731651 ∅ 110 – 220 85010002 light / medium / heavy light / medium / heavy Downtilt kit ∅ 42 – 115 ∅ 210 – 380 Remark 738546 Page 192 85010003 light 732327 193 light / medium 737978 194 heavy 85010008 195 light / medium 85010014 heavy 85010015 light / medium 85010016 heavy 85010017 Downtilt kit Downtilt kit 3 Sector Clamp light / medium heavy Offset ∅ 88.9 ∅ 88.9 ∅ 114.3 ∅ 139.7 ∅ 114.3 ∅ 139.7 light / medium light / medium 742113 light / medium 85010075 heavy 85010076 Tension Band light Wall mounting adjustment angle ±30° 196 197 3 sector clamp 85010060Mounting supportClearance between pole clamp and antenna (additional clamp needed) 85010061 heavy 2x Panel Mounting Kit 742263 742317 742033 742034 85010058 85010059 196 F Azimuth Adjustment Kit Pole mounting adjustment angle ±30° (additional clamp needed) G Azimuth Adjustment Kit ∅ 34 – 60 ∅ 60 – 80 ∅ 80 – 100 ∅ 100 – 120 ∅ 120 – 140 ∅ 45 – 125 734360 734361 734362 734363 734364 734365 198 199 Additional clamp needed 200 Please note: Only usable without downtilt kit 201 New product 191 Panel Accessories Mounting Hardware Clamps Clamps Suitable for mast diameter Antenna – mast distance F Number of pieces Material – Clamp – Screws Weight 738546 731651 Type No. 85010002 85010003 28 – 60 mm 42 – 115 mm 110 – 220 mm 210 – 380 mm 25 – 28 mm 20 – 26 mm 47 – 55 mm 48 – 68 mm 1 clamp 1 clamp 1 clamp 1 clamp Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel/ Hot-dip galvanized steel/ Hot-dip galvanized steel/ Stainless steel/ Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel 0.8 kg 1.1 kg 2.7 kg 4.8 kg – Nuts A E Torque MA = G K C B F 35 ∅ D Torque: M8 => MA = 20 Nm M6 => MA = 8 Nm I H Type No. A B C D E F G H I K 731651 738546 85010002 85010003 116 mm 152 mm 280 mm 442 mm 40 mm 40 mm 100 mm 150 mm 40 mm 40 mm 50 mm 50 mm 28 – 60 mm 42 – 115 mm 110 – 220 mm 210 – 380 mm 93 mm 93 mm 93 mm 150 mm 25 – 28 mm 20 – 26 mm 47 – 55 mm 48 – 68 mm 20 Nm 25 Nm 35 Nm 35 Nm 84 mm 125 mm 240 mm 392 mm – 72 mm 72 mm 72 mm 64 mm 64 mm 64 mm 64 mm Please note: Kathrein does not recommend to use counter nuts. The additional nuts supplied are only meant as spares. 192 Standard Downtilt kit for Panel Antennas (Wind load Category “L”) Downtilt kit Type No. Preferred range of use Weight Material Screws Nuts / washers 732327 – Panel antennas with attached mounting plates – Downtilt kit without scale for universal use 1.3 kg Hot-dip galvanized steel Hot-dip galvanized steel / stainless steel Stainless steel 20 Nm / M8 20 Nm / M8 64 230 Before the adjustment, all joint screws must be loosened. After the adjustment has been completed, all loosened screws must be tightened. Recommended torque for M8 bolted connections: 20 Nm. Ø 8.5 20 Nm / M8 Mounting accessories included. Ø 8.5 45 64 115 60 20 Nm / M8 Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna. Mounting this downtilt kit enlarges the spacing between mast and antenna by 60 mm. Use the downtilt kit together with the clamps as described in the antenna datasheet. 193 Standard Downtilt kit for Panel Antennas (Wind load Category “L” and “M”) Downtilt kit Type No. Preferred range of use Weight Material Screws Nuts / washers 737978 – Panel antennas with attached mounting plates – Downtilt kit without scale for universal use 2.3 kg Hot-dip galvanized steel Hot-dip galvanized steel / stainless steel Stainless steel 20 Nm / M8 20 Nm / M8 64 336 Before the adjustment, all joint screws must be loosened. After the adjustment has been completed, all loosened screws must be tightened. 70 Ø 8.5 50 Nm / M12 Mounting accessories included. Ø 8.5 50 64 115 20 Nm / M8 Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna. Mounting this downtilt kit enlarges the spacing between mast and antenna by 70 mm. Use the downtilt kit together with the clamps as described in the antenna datasheet. 194 70 Standard Downtilt kit for Panel Antennas (Wind load Category “H”) Special downtilt kit for Panel antennas with a higher wind load. Downtilt kit 85010008 Type No. Preferred range of use Weight Material Screws Nuts – Panel antennas with a higher wind load – Panel antennas with attached mounting plates – Downtilt kit without scale for universal use 4.3 kg Hot-dip galvanized steel Hot-dip galvanized steel / stainless steel Stainless steel M10 M8 Mounting accessories included Recommended mast clamps: Type No. Description Mast diameter Weight approx. Units per antenna 738546 85010002 85010003 1 clamp 1 clamp 1 clamp 42 – 115 mm 110 – 220 mm 210 – 380 mm 1.1 kg 2.9 kg 4.8 kg 2 2 2 Recommended torque for all bolted connections: Torque M8 M10 20 Nm 50 Nm Ø 8.5 Screw size Maximum acceptable load: < 5000 N < 1300 N 100 Instructions to adjust the required downtilt angle are given in the datasheet or on the rearside of the antenna. Ø 8.5 305 65 Frontal wind load Lateral wind load 72 72 Mounting this downtilt kit enlarges the spacing between mast and antenna by 100 mm. Use the downtilt kit together with the clamps as described in the antenna datasheet. 155 100 195 All Panels Mounting Hardware Azimuth Adjustment Kits Pole mounting Wall mounting Detail Y X 358 308±1 109 MA 46 86 50 104 62±0.5 Distance B see table 43 ∅ 15 ±0.5 14 106 180±1 The azimuth adjustment kit for pole mounting can be mounted with all suitable clamps, 3-Sector clamps and 2x Panel mounting kits (with the latter only as an interface between mounting kit and antenna). Type No. Suitable for Number of pieces Distance between screws [B] Angular range Weight / kit Supplied mounting accessories Materials Max. permissible static load / kit – X direction – Y direction 85010014 85010015 85010016 85010017 2 brackets 64 mm 2 brackets 72 mm 2 brackets 64 mm 2 brackets 72 mm pole mounting ± 30° approx. 2500 g approx. 2500 g all screws Screws and dowels for wall fastening are not supplied, they must be chosen by installer according to on-site requirements. Adapter for downtilt kit Adapter for downtilt kit 7323xx series 7323xx series Parts are hot-dip galvanized steel; Captive nuts are stainless steel approx. 1260 g 2150 N 760 N ± 30° approx. 1260 g 5100 N 1350 N 2150 N 760 N Recommended torque: Screws M6: 8 Nm; Screws M8: 20 Nm; MoS2 greased. Minimum torque MA: 30 Nm; MoS2 greased 196 wall mounting 5100 N 1350 N 3 Sector Panel Arrangement 3 Sector Clamp Kit Mounting Hardware Slim and unobstrusive design. Nearly cylindrical optical appearance with small outer diameter. l Suitable for all Panels with an antenna housing width less than 400 mm (Hmax). Please note: Panels with connector position “Rearside” fit only with downtilt kit azimuth adjustment kit or offset mounted in-between. l l E 3 sector clamp Torque MA = 25 Nm F B 60 ° M8 C G A Mounting support clamp Torque MA = 7 Nm D t E 64 64 64 64 72 72 F 50 50 50 50 50 50 G 45 45 45 45 45 45 Hmax 280 361 375 400 375 400 3 Sector Clamp Kit (Antenna Wind load Category “L” and “M”) Type No. Angle between antennas Suitable for mast diameter Number of pieces Material – 3 sector clamp – Mounting support clamp – Screws / threaded stud – Nuts 742263 742317 Angle between antennas Suitable for mast diameter Number of pieces Material – 3 sector clamp – Mounting support clamp – Screws / threaded stud – Nuts 742033 Bottom view without downtilt kit 742034 120° 120° 120° 120° 88.9 mm 88.9 mm 114.3 mm 139.7 mm 2 x 3 sector clamp 2 x 3 sector clamp 2 x 3 sector clamp 2 x 3 sector clamp 2 x mounting support clamp 2 x mounting support clamp 2 x mounting support clamp 2 x mounting support clamp Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Aluminum Aluminum Aluminum Aluminum Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Hot-dip galvanized steel Stainless steel Stainless steel Stainless steel Stainless steel 3 Sector Clamp Kit (Antenna Wind load Category “H”) Type No. Weight 4 kg 4 kg 4 kg 4 kg 4 kg 4 kg Hm Type No. A B C D 742263 168 88.9 65 180 742317 199 88.9 88 213 742033 114.3 207 92 217 742034 139.7 100 236 228 85010058 114.3 207 92 217 85010059 139.7 100 236 228 All dimensions in mm. Dout is determined by mounted components. ax D ou 85010058 85010059 120° 114.3 mm 2 x 3 sector clamp 2 x mounting support clamp 120° 139.7 mm 2 x 3 sector clamp 2 x mounting support clamp Hot-dip galvanized steel Aluminum Hot-dip galvanized steel Stainless steel Hot-dip galvanized steel Aluminum Hot-dip galvanized steel Stainless steel 197 Mounting Hardware Offset for Panel Antennas Type No. Wind load category Quantity needed per antenna Material: – spacer – nuts Dimension “A” Weight Scope of supply 85010060 “L” and “M” 85010061 “H” 2 x spacer Hot-dip galvanized steel Stainless steel 64 mm 72 mm 0.65 kg 1 x spacer, Fitting accessories Recommended torque for M8 bolted connections: 20 Nm Please use the offset in combination with clamps corresponding to the pole diameter. A Mounting accessories (order separately) Possible clamps in combination with: 85010060 Type No. Description Mast diameter Weight approx. Units per antenna 731651 738546 85010002 85010003 742263 742317 742033 742034 1 clamp 1 clamp 1 clamp 1 clamp 2 x 3 sector clamp 2 x 3 sector clamp 2 x 3 sector clamp 2 x 3 sector clamp 28 – 64 mm 42 – 115 mm 110 – 220 mm 210 – 380 mm 88.9 mm 88.9 mm 114.3 mm 139.7 mm 0.8 kg 1.1 kg 2.9 kg 4.8 kg 4.0 kg 4.0 kg 4.0 kg 4.0 kg 2 2 2 2 1 1 1 1 Type No. Description Mast diameter Weight approx. Units per antenna 738546 85010002 85010003 85010058 85010059 1 clamp 1 clamp 1 clamp 2 x 3 sector clamp 2 x 3 sector clamp 42 – 115 mm 110 – 220 mm 210 – 380 mm 114.3 mm 139.7 mm 1.1 kg 2.9 kg 4.8 kg 4.0 kg 4.0 kg 2 2 2 1 1 85010061 If a downtilt kit is used, please choose the fitting one from the antenna data sheet. 198 42 77 104 90 Panel Accessories 2 x Panel Mounting Kit for Panels width 112 mm and 155 mm Use this mounting kit only for Panels with a maximum width of 160 mm. Wind load category: L (Light) or M (Medium) 2 x Panel Mounting Kit 742113 Type No. Contens Material: – Clamp and screws – Nuts and washers Weight 2 x brackets and mounting accessories Hot-dip galvanized steel Stainless steel Approx. 1.6 kg Recommended torque for M8 bolted connections: 20 Nm 90 72±0.3 10 118 75 30° 19 9 64±0.3 9 38 Ø not be kit can and g in t moun 0644 : This nnas 8001 s, please n o i t n ante Atte enna for the r these ant 010075. used 5 o g kit 8 744. F 80010 the mountin use 64±0.3 64±0.3 82.5 82.5 270 Configuration without mechanical downtilt 64±0.5 Ø9 63 0 9 –0.5 75±1 10±1 33 101 Configuration with mechanical downtilt 64±0.3 72±0.3 Use the 2 x Panel Mounting Kit together with the following mounting accessories Type No. Description Remarks 731651 738546 85010002 85010003 85010060 737978 1 clamp 1 clamp 1 clamp 1 clamp 1 offset 1 downtilt kit Mast: 28 – 60 mm diameter Mast: 42 – 115 mm diameter Mast: 110 – 220 mm diameter Mast: 210 – 380 mm diameter in combination with the clamps Downtilt angle: depending on antenna height Weight Units per approx. antenna 0.8 kg 1.1 kg 2.7 kg 4.8 kg 1.3 kg 2.3 kg 2 2 2 2 2 1 For a three sector panel arrangement, use the mounting kit type no. 742113 together with the three sector clamp 742213, 742033 or 742034. Three sector clamp 742263 does not match. If a downtilt kit is used, please choose the fitting one from the antenna datasheet. 199 2 x Panel Mounting Kit Use this mounting kit for Panels with a maximum width of 325 mm. Type No. Contens Material: – Clamp and screws – Nuts and washers Weight Hole distance “A” Windload category (Antenna) 85010075 85010076 2 x brackets and mounting accessories Hot-dip galvanized steel Stainless steel Approx. 3.3 kg 64 mm 72 mm “L” and “M” “H” Recommended torque for M8 bolted connections: 20 Nm 5 442 330 threaded bolts M8 60 18.5 64 72 A R5 0 R5 0 A 22 35 Configuration without mechanical downtilt Configuration with mechanical downtilt Mounting Accessories (order separately) Clamps (only the listed clamps are allowed!) Type No. Description Remarks 85010002 85010003 85010060 85010061 1 clamp 1 clamp 1 offset 1 offset Mast: 110 – 220 mm diameter Mast: 210 – 380 mm diameter Weight Units per approx. antenna 2.7 kg 4.8 kg 1.3 kg 1.3 kg If a downtilt kit is used, please choose the fitting one from the antenna datasheet. 200 2 2 2 2 Mounting Hardware Tension Band for Panel Antennas (Wind load Category “L”) Type No. Suitable for mast diameter Material Weight (approx.) 734360 734361 734362 734363 734364 734365 34 – 60 mm Stainless steel 0.06 kg Only 60 – 80 mm Stainless steel 0.07 kg 80 – 100 mm Stainless steel 0.08 kg 100 – 120 mm Stainless steel 0.09 kg 120 – 140 mm Stainless steel 0.11 kg 45 – 125 mm Stainless steel 0.08 kg : e note wntilt kit! s a e l P t do ithou w e l b sa u 201 Side-mounting Clamp Omnidirectional Antennas Large Pipe Type No. 738908 For masts of 94 – 125 mm diameter Antenna Mast b a b a 202 Side-mounting Bracket Omnidirectional Antennas ∅D Type No. 737398 Side-mounted bracket (for mast diameters of 40 – 105 mm) Type No. 737398 Bracket A At the bottom only 800/900 MHz 736347 736349 736350 738192 80010850 Fits for antenna type no. 1800 MHz 738187 UMTS 741790 Side-mounting is possible for four fixed distances between the tubular mast and the antenna: 800/900 MHz (holes 1 and 3) A = 100 mm = 0.3 λ A A 1800/2000 MHz (hole 2) A = 160 mm = 0.5 λ A A A A = 240 mm = 0.75 λ A A A A = 80 mm = 0.5 λ A A A et acket Bracket nna Antenna na asebase Antenna base Mast ket Bracket Bracket Bracket D Pipe D Hole Hole 3 Hole 3 3 Horizonal Radiation Pattern D D Hole Hole 1 Hole 1 1 D Spacing A Curve Pipe D D D D Horizonal Radiation Pattern 100 mm 160 mm 3 0 direction from mast to antenna 100 mm 100 mm Pipe D Curve Horizonal Radiation Pattern 0 direction from mast to antenna Spacing A 80 mm 3 240 mm D 40 mm 160 mm 3 240 mm Spacing A Curve Hole 2 D dB 40 mm Hole Hole 3 Hole 3 3 100 mm dB D dB D 0 direction from mast to antenna 203 Side-mounting Brackets Omnidirectional Antennas For mast diameters of 40 – 105 mm Type No. K61335 Bracket At the bottom only Fits for antenna type no. K75116.. K75156.. Side mounting is possible for three fixed distances between the tubular mast and the antenna: 100 mm = 0.3 λ 160 mm = 0.5 λ 240 mm = 0.75 λ Pipe D Horizontal Radiation Pattern 3 Additional gain to the nominal value of the antenna gain 100 mm 2 dB 160 mm 3 dB 240 mm 2 dB 100 mm 2.5 dB 160 mm 3.5 dB 240 mm 2.5 dB dB 40 mm Spacing A Curve 0 direction from mast to antenna 3 dB 100 mm 0 direction from mast to antenna 204 All Panels Accessories Azimuth Adjustment Tool Type No. 738440 Precise azimuth adjustment for mast mounted antennas can easily be achieved by using the azimuth adjustment tool. This tool is suitable to all types of Panels and Tri-Sector Pipe Antennas with a maximum width of 315 mm. Target object Scale Target object Elevation compensation Move the stopper to central position* Panel Clamping device Instruction: – Use a map to work out the angle between the designed antenna azimuth and target (church, building, mountain peak). – Set this angle on the scale of the adjustment tool. – Place the adjustment tool onto the antenna and tighten the clamping device. – Use the telescope to aim at the target object, if necessary, use elevation compensation. – Then rotate the antenna until the target object appears in the telescope. * Observe the position of the stopper when fitting the azimuth adjustment tool. 205 206 Filters / Duplexers Multiband Combiners Dual-Band Combiners Triple-Band Combiners Quad-Band Combiners Same-Band Combiners Hybrid Combiners Same-Band Combiner Duplex Hybrid Combiner Active Duplex Hybrid Combiner Hybrid Combiner 3-dB Couplers Hybrid Ring Junctions System Components Bias Tees Measuring Directional Couplers DC-Stops Attenuators 50-Ω Loads DTMAs 207 Summary of Filter, Combiner and Amplifier Types The articles are listed by type number in numerical order. Type No. 208 Page Type No. Page Type No. Page Type No. Page 78210161 224 78210577 322 78210850V01 319 78211133 266, 267 78210162 224 78210578 323 78210860 360 78211134 266, 267 78210164 224 78210580 343 78210874 337 78211135 266, 267 78210165 224 78210581 344 78210876 352 78211141 288, 289 78210167 225 78210583 345 78210877 351 78211142 288, 289 78210168 220, 221 78210610 353 78210900 274, 275 78211143 288, 289 78210169 220, 221 78210612 353 78210901 274, 275 78211144 288, 289 78210170 220, 221 78210613 354, 355 78210925 304, 305 78211145 356 78210171 220, 221 78210620 252, 253 78210926 306, 307 78211149 214 78210172 220, 221 78210621 252, 253 78210930 294, 295 78211159 214 78210192 228 78210622 252, 253 78210931 296, 297 78211180 262, 263 78210193 228 78210623 252, 253 78210936 298, 299 78211181 262, 263 78210215 222, 223 78210624 252, 253 78210970 240, 241 78211182 262, 263 78210216 222, 223 78210625 252, 253 78210971 240, 241 78211183 262, 263 78210257 222, 223 78210626 254, 255 78210972 240, 241 78211184 262, 263 78210264 237 78210630 264, 265 78210973 240, 241 78211185 262, 263 78210265 222, 223 78210631 264, 265 78210974 240, 241 78211190 268, 269 78210278 250, 251 78210632 264, 265 78210975 240, 241 78211191 268, 269 78210279 250, 251 78210633 264, 265 78210979 242, 243 78211192 268, 269 78210305 250, 251 78210634 264, 265 78210990 349, 350 78211193 268, 269 78210306 250, 251 78210635 264, 265 78211053 324 – 326 78211209 287 78210341 235 78210640 270, 271 78211054 324 – 326 78211210 287 78210390 218, 219 78210641 270, 271 78211055 324 – 326 78211211 287 78210391 218, 219 78210642 270, 271 78211056 324 – 326 78211212 287 78210392 217 78210643 270, 271 78211063 324 – 326 78211213 287 78210415 226 78210644 270, 271 78211064 324 – 326 78211230 300, 301 78210429 321 78210645 270, 271 78211065 324 – 326 78410235 302, 303 78210430 336 78210649 272, 273 78211066 324 – 326 78211239 216 78210440 340 78210660 244, 245 78211091 258, 259 78211240 216 78210442 340 78210661 244, 245 78211092 258, 259 78211245 357 78210457 238, 239 78210662 244, 245 78211093 258, 259 78211249 215 78210458 238, 239 78210663 244, 245 78211094 258, 259 78211259 215 78210460 238, 239 78210664 244, 245 78211095 258, 259 78410235 330 78210469 256 78210665 244, 245 78211099 260, 261 78410236 330 78210474 327 78210669 246, 247 78211102 358, 359 78410237 330 78210490 341 78210680 248, 249 78211103 346, 347 78410238 330 78210495 342 78210681 248, 249 78211104 358, 359 78410367 328 78210500 283 78210682 248, 249 78211105 346, 347 78410470 328 78210502 284 78210683 248, 249 78211106 348 78210504 285 78210800 258, 259 78211110 292, 293 78210510 338, 339 78210805 290, 291 78211120 353 78210511 338, 339 78210808 256 78211130 266, 267 78210524 310, 311 78210809 257 78211131 266, 267 78210534 286 78210810 257 78211132 266, 267 Summary of Filter, Combiner and Amplifier Types The articles are listed by type number in numerical order. Type No. Page 728954 234 790881 308, 309 791145 236 791498 308, 309 791918 330 791919 330 791920 330 791921 330 792542 226 792544 227 792699 280 792702 281 792972 331 793006 313 793301 318 793304 320 793506 312 793554 314 793555 282 K6226111 328 K6226201 329 K6226207 329 K6226211 329 K6226217 329 K6226301 329 K6226307 329 K6226311 329 K6226317 329 K6226401 328 K6226411 328 K6226501 329 K6226507 329 K6226511 329 K6226611 328 K6373621 308, 309 New Products 209 210 Filters / Duplexers 211 212 Summary of Filter and Duplexer Types Filters: Description Type No. Frequency range Max. input power Page Band-pass Filter Band-pass Filter Band-pass Filter Band-pass Filter Band-pass Filter Band-pass Filter Band-pass Filter Band-pass Filter Band-pass Filter 78211149 78211159 78211249 78211259 78211239 78211240 78210392 78210390 78210391 801 – 862 MHz 801 – 862 MHz 791 - 862 MHz 791 - 862 MHz 791 - 862 MHz 791 - 862 MHz 824 – 888 MHz 890 – 960 MHz 890 – 960 MHz 100 W 100 W 100 W 100 W 100 W 100 W 400 W 400 W 400 W 214 214 215 215 216 216 217 218, 219 218, 219 Description Type No. Frequency range Max. input power Page Duplexer 78210168 400 W 220, 221 Duplexer 78210169 400 W 220, 221 Duplexer 78210170 400 W 220, 221 Duplexer 78210171 400 W 220, 221 Duplexer 78210172 400 W 220, 221 Duplexer 78210215 400 W 222, 223 Duplexer 78210216 400 W 222, 223 Duplexer 78210257 400 W 222, 223 Duplexer 78210265 800 W 222, 223 Duplexer 78210164 500 W 224 Duplexer 78210165 500 W 224 Duplexer 78210161 500 W 224 Duplexer 78210162 500 W 224 Duplexer 78210167 250 W 225 Duplexer 792542 250 W 226 Duplexer 78210415 250 W 226 Duplexer 792544 300 W 227 Duplexer 78210192 250 W 228 Duplexer 78210193 250 W 228 Duplexers: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: Low band: High band: 824 – 835 MHz 869 – 880 MHz 824 – 835 MHz 869 – 880 MHz 824 – 835 MHz 869 – 880 MHz 835 – 851 MHz 880 – 896 MHz 835 – 851 MHz 880 – 896 MHz 824 – 851 MHz 869 – 896 MHz 824 – 851 MHz 869 – 896 MHz 824 – 846.5 MHz 869 – 891.5 MHz 824 – 846.5 MHz 869 – 891.5 MHz 890 – 915 MHz 935 – 960 MHz 890 – 915 MHz 935 – 960 MHz 890 – 915 MHz 935 – 960 MHz 890 – 915 MHz 935 – 960 MHz 880 – 915 MHz 925 – 960 MHz 1710 – 1785 MHz 1805 – 1880 MHz 1710 – 1785 MHz 1805 – 1880 MHz 1850 – 1910 MHz 1930 – 1990 MHz 1920 – 1980 MHz 2110 – 2170 MHz 1920 – 1980 MHz 2110 – 2170 MHz New Products 213 Band-pass Filter 801 - 862 MHz • Band-pass Filter for LTE800 with DVB-T suppression • Available as a single unit or for XPol antennas as a double unit • Wall or mast mounting 78211149 78211159 Diagram II 0 Attenuation/dB Attenuation/dB Typical Attenuation Curves Diagram I 0.5 1.0 801 – 862 1.5 0 5 10 2.0 20 2.5 25 3.0 30 3.5 35 4.0 40 4.5 45 5.0 770 780 790 800 810 820 830 840 850 860 870 801 – 862 15 50 770 780 790 800 810 820 830 Technical Data Type No. 78211149 Pass band Insertion loss Stop band attenuation 78211159 Single Unit Double Unit 801 - 862 MHz < 0.3 dB (typ. 0.2 dB) > 35 dB (470 - 790 MHz) VSWR < 1.2 Impedance 50 Ω Input power Intermodulation products < 100 W < -160 dBc (with 2 x 20 W) Temperature range -40 ... +65 °C DC/AISG Application Weight Mounting Dimensions (w x h x d) 214 Accessories (order separately) Type No. Bypass Connectors Clamp set suitable for mast diameter of 7-16 female 734360 34 - 60 mm Outdoor (IP 66) 734361 60 - 80 mm 1.1 kg 2.2 kg Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 105 x 180 x 60 mm 840 850 Frequency/MHz Frequency/MHz 215 x 180 x 60 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm 860 870 Band-pass Filter 791 - 862 MHz • Band-pass Filter for LTE800 with DVB-T suppression • Available as a single unit or for XPol antennas as a double unit • Wall or mast mounting 78211249 78211259 Typical Attenuation Curves Diagram I Diagram II Frequency/MHz Frequency/MHz Technical Data Type No. 78211249 Pass band Insertion loss Stop band attenuation 78211259 Single Unit Double Unit 791 - 862 MHz < 0.3 dB (typ. 0.2 dB) > 35 dB (470 - 782 MHz) VSWR < 1.2 Impedance 50 Ω Input power Intermodulation products < 100 W < -160 dBc (with 2 x 20 W) Temperature range -40 ... +65 °C DC/AISG Application Weight Mounting Dimensions (w x h x d) Type No. Bypass Connectors Accessories (order separately) Clamp set suitable for mast diameter of 7-16 female 734360 34 - 60 mm Outdoor (IP 66) 734361 60 - 80 mm 1.1 kg 2.2 kg Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 105 x 180 x 60 mm 215 x 180 x 60 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm 215 Band-pass Filter 791 - 862 MHz • Band-pass Filter for LTE800 with DVB-T suppression • Available as a single unit or for XPol antennas as a double unit • Wall or mast mounting Typical Attenuation Curves Diagram I Diagram II Frequency/MHz Frequency/MHz Technical Data Type No. Pass band Insertion loss Stop band attenuation 78211240 78211239 Single Unit Double Unit 791 - 862 MHz Typically 0.6 dB (max. 1,5 dB) > 18 dB (470 - 790 MHz) < 1.2 VSWR Impedance 50 Ω Input power < 100 W Intermodulation products < -160 dBc (with 2 x 20 W) Temperature range -40 ... +65 °C DC/AISG Connectors 7-16 female Application Outdoor (IP 66) Weight Mounting Dimensions (w x h x d) 216 Accessories (order separately) Bypass 2,9 kg Type No. 734360 5,8 kg Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 140 x 291 x 71 mm 285 x 291 x 71 mm Clamp set suitable for mast diameter of 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm • AMPS/CDMA850 Tx/Rx filter • Suppression of spurious emissions at adjacent Port 2 GSM900 Rx frequencys • Suitable for indoor applications • Built-in DC stop Port 1 Port 2 Typical Attenuation Curves Diagram I 824 888 890 960 824 888 890 960 Port 1 Technical Data Type No. Pass band Insertion loss Stop band attenuation VSWR Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 � Port 2 Mounting Weight Packing size Dimensions (w x h x d) 78210392 824 – 888 MHz < 0.5 dB (824 – 885 MHz) < 0.8 dB (885 – 886 MHz) < 1.5 dB (886 – 888 MHz) > 40 dB (890 – 960 MHz) < 1.25 50 Ω < 400 W (824 – 888 MHz) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +55 °C Port 1: 7-16 female (long neck) / Port 2: 7-16 male Diagram II Indoor Stop With 4 screws (max. 4 mm diameter) 2 kg 387 x 137 x 130 mm 89 x 73.3 x 308.5 mm (including connectors and mounting feet) 225 217 Filters / Duplexers Band-pass Band-pass Filter Filter 824 888 MHz MHz (AMPS/CDMA850) (AMPS/CDMA850) 824 – – 888 Band-pass Filter 890 - 960 MHz (GSM 900) • GSM 900 Tx/Rx preselector filter • Suppression of interfering Tx signals of an adjacent AMPS or CDMA frequency band Port 1 Port 2 • Suitable for indoor or outdoor applications • Built-in DC stop Port 1 Port 2 Technical Data Type No. Stop band Frequency spacing Subject to alteration. Pass band 78210391 0 - 888 MHz 2 MHz 0 - 889 MHz 1 MHz 890 - 960 MHz 890 - 960 MHz Insertion loss < 1.5 dB (890 - 892 MHz) < 0.8 dB (892 - 893 MHz) < 0.6 dB (893 - 905 MHz) < 0.3 dB (905 - 960 MHz) Typ. 4.0 dB (890 - 890,5 MHz) @ -5 ... +45° < 2.5 dB (890,5 - 891 MHz) < 1.5 dB (891 - 892 MHz) < 1.0 dB (892 - 893 MHz) < 0.6 dB (893 - 905 MHz) < 0.3 dB (905 - 960 MHz) Stop band attenuation > 50 dB (0 – 880 MHz) > 40 dB (880 – 885 MHz) > 30 dB (885 – 888 MHz) > 50 dB (0 – 869 MHz) > 30 dB (869 – 888.75 MHz) > 30 dB (888.75 – 889 MHz) @ -5 ... +45° < 1.25 (890 - 960 MHz) < 1.3 (891 - 960 MHz) VSWR Impedance 50 Ω Input power < 400 W (935 - 960 MHz) Intermodulation products Temperature range 936.2758e 78210390 < -160 dBc (3rd order; with 2 x 20 W) -40 ... +60 °C Connectors Port 1: 7-16 female, long neck / Port 2: 7-16 male Application Indoor or outdoor (IP66) DC/AISG transparency Port 1 ↔ Port 2 Mounting Weight Packing size Dimensions (w x h x d) www.kathrein.de Stop With 4 screws (max. 4 mm diameter) 2 kg 387 x 137 x 130 mm 114 x 84 mm x 377 mm (including connectors and mounting feet) 78210390, 78210391 Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 218 Band-pass Filter 890 - 960 MHz (GSM 900) 78210391 Typical Attenuation Curves Diagram I 0 890 – 960 20 30 10 40 50 50 60 60 70 70 80 80 90 90 885 895 905 915 925 935 945 955 Frequency/MHz 100 865 965 875 885 895 Diagram II 0.5 1.5 890 – 960 0 – 888 1.0 1.5 2.5 2.5 3.0 3.0 3.5 3.5 4.0 4.0 4.5 4.5 Type No. 885 895 905 915 925 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm 935 945 955 965 5.0 865 Frequency/MHz Clamp set suitable for mast diameter of 734360 935 945 955 965 955 965 0.5 2.0 875 925 0 2.0 5.0 865 915 Diagram II 0 1.0 905 Frequency/MHz Attenuation/dB Attenuation/dB 875 890 - 960 30 40 100 865 0 - 889 20 Clamp Set 0 - 889 875 890 - 960 885 895 905 915 925 935 945 Frequency/MHz Please Note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of a mast mounted device or even cause it to fall to the ground. These facts must be considered during the site planning process. The Band-pass Filters are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E and have passed environmental tests as recommended in ETS 300 019-2-4. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the combiners and accessories. The limits for the coupling torque of RF connectors, recommended by the connector manufacturers must be obeyed. Any previous datasheet issues have now become invalid. Page 2 of 2 78210390, 78210391 Subject to alteration. 0 – 888 0 www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 219 936.2758e 10 Attenuation/dB Attenuation/dB 78210390 Typical Attenuation Curves Diagram I Duplexer Duplexer 824 835 // 869 869 –– 880 880 MHz MHz (AMPS (AMPS A-Band) A-Band) 824 –– 835 835 851 // 880 880 –– 896 896 MHz MHz (AMPS (AMPS B-Band) B-Band) 835 –– 851 The Duplexer is designed to combine/split GSM Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • 78210168: AMPS A-Band, indoor version • 78210169: AMPS A-Band, outdoor version • 78210170: AMPS A-Band, indoor version 78210168 78210171 (indoor) mounted onto a 19˝ drawer Low band • • 78210172: AMPS B-Band, outdoor version 78210171: AMPS B-Band, indoor version Antenna High band 78210169 78210172 (outdoor) Low band Low band Antenna Low band Antenna Antenna High band High band High band 78210170 (19˝ drawer) Technical Data Type No. Pass band Low band High band Insertion loss Antenna Low band High band Antenna Isolation Low band High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 226 220 78210168 78210169 AMPS A-Band 78210170 78210171 78210172 AMPS B-Band 824 – 835 MHz 869 – 880 MHz 835 – 851 MHz 880 – 896 MHz < 0.5 dB (824 – 835 MHz) < 0.5 dB (869 – 880 MHz) < 0.5 dB (835 – 851 MHz) < 0.5 dB (880 – 896 MHz) > 85 dB (824 – 835 / 869 – 880 MHz) > 85 dB (835 – 851 / 880 – 896 MHz) < 1.25 (824 – 835 / 869 – 880 MHz) < 1.25 (835 – 851 / 880 – 896 MHz) 50 Ω 50 Ω < 400 W (high band; with max. 8 carriers) < 400 W (high band; with max. 12 carriers) < –160 dBc (3 rd order; with 2 x 20 W) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C –40 ... +60 °C –20 ... +55 °C –20 ... +55 °C –40 ... +60 °C 7-16 female 7-16 female Indoor Outdoor (IP 66) Indoor, 19˝ drawer Indoor Outdoor (IP 66) Built-in DC stop between all ports Built-in DC stop between all ports With 4 screws Wall mounting With 4 screws With 4 screws Wall mounting with 4 screws (max. 4 mm diameter) with 4 screws (max. 6 mm diameter) (max. 4 mm diameter) (max. 8 mm diameter) (max. 8 mm diameter) Mast mounting with Mast mounting with additional clamp set additional clamp set 2.8 kg 5.5 kg 3.7 kg 2.8 kg 5.5 kg 309 x 162 x 252 mm 347 x 297 x 174 mm 612 x 312 x 224 mm 309 x 162 x 252 mm 347 x 297 x 174 mm 229 x 80 x 169.6 mm 238 x 305 x 93.5 mm 19˝ drawer, 229 x 80 x 169.6 mm 238 x 305 x 93.5 mm (including connectors (including mounting 2 height units, plug- (including connectors (including mounting feet) and mounting feet) feet) in depth 170 mm and mounting feet) Filters / Duplexers Duplexer Duplexer 824 – – 835 824 835 // 869 869 –– 880 880 MHz MHz (AMPS (AMPS A-Band) A-Band) 835 – – 851 835 851 // 880 880 –– 896 896 MHz MHz (AMPS (AMPS B-Band) B-Band) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Clamp Set Typical Attenuation Curves (78210168, 78210169, 78210170) Diagram I Antenna Low band 0 Attenuation/dB Attenuation/dB Diagram II High band Antenna Antenna Low band 10 20 824 – 835 30 869 – 880 0.5 1.0 2.0 50 2.5 60 3.0 70 3.5 80 4.0 90 4.5 812 822 832 842 852 862 872 882 892 Frequency/MHz 5.0 902 802 Typical Attenuation Curves (78210171, 78210172) Diagram I 10 880 – 896 835 – 851 30 1.0 2.5 60 3.0 70 3.5 80 4.0 90 4.5 845 855 865 875 885 895 905 Frequency/MHz 852 915 862 872 882 Frequency/MHz 892 902 High band Antenna 5.0 815 880 – 896 835 – 851 1.5 50 835 842 0.5 2.0 825 832 0 40 100 815 822 Antenna Low band 0 20 812 Diagram II High band Antenna Attenuation/dB Attenuation/dB Antenna Low band 869 – 880 824 – 835 1.5 40 100 802 High band Antenna 0 825 835 845 855 865 875 885 895 Frequency/MHz 905 915 221 227 Duplexer Duplexer 824 –– 851 851 // 869 869 –– 896 896 MHz MHz (AMPS (AMPS A/B-Band) A/B-Band) 824 824 –– 846.5 846.5 // 869 869 –– 891.5 891.5 MHz MHz (AMPS (AMPS A/B-Band) A/B-Band) 824 78210215 78210257 ø4 .3 169.6 • Suitable for indoor application • Built-in DC stop 229 219 134 148 The Duplexer is designed to combine/split AMPS Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. 50 27.5 59.5 206 91.5 Low Band Antenna 78210216 High Band 229 219 175.4 134 148 ø4 .3 max. 80 27.5 59.5 91.5 206 Low Band Antenna 78210265 High Band 229 219 .3 50 max. 80 ø4 78210215, 78210257 170 134 148 78210216 71.5 max. 112 27.5 59.5 206 91.5 Low Band Antenna High Band Technical Data Type No. Pass band Low band High band Insertion loss Antenna Low band High band Antenna Isolation Low band High band VSWR Impedance Input power 78210215 78210216 78210265 AMPS A/B-Band (reduced bandwidth) 824 – 851 MHz 869 – 896 MHz 824 – 846.5 MHz 869 – 891.5 MHz < 0.5 dB (824 – 851 MHz) < 0.5 dB (869 – 896 MHz) < 0.5 dB (824 – 846.5 MHz) < 0.5 dB (869 – 891.5 MHz) > 65 dB (824 – 851 / 869 – 896 MHz) > 70 dB (824 – 846.5 / 869 – 891.5 MHz) < 1.25 (824 – 851 / 869 – 896 MHz) 50 Ω < 400 W (high band; with max. 16 carriers) < 1.25 (824 – 846.5 / 869 – 891.5 MHz) 50 Ω < 400 W (high band; < 800 W (high band; with max. 16 carriers) with max. 32 carriers) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C Intermodulation products Temperature range < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 7-16 female 222 228 78210257 AMPS A/B-Band N female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 2.6 kg 309 x 252 x 162 mm 229 x 80 x 169.6 mm 229 x 80 x 175.4 mm (including connectors and mounting feet) 7-16 female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 2.6 kg Approx. 3 kg 309 x 252 x 162 mm 309 x 252 x 162 mm 229 x 80 x 169.6 mm 229 x 112 x 170 mm (including connectors and mounting feet) Typical Attenuation Curves (78210215, 78210216) Diagram I Antenna Low band 0 10 20 824 – 851 30 Diagram II High band Antenna Attenuation/dB Attenuation/dB Antenna Low band 869 – 896 0.5 1.0 50 2.5 60 3.0 70 3.5 80 4.0 90 4.5 830 840 850 860 870 880 890 900 Frequency/MHz 5.0 810 910 Typical Attenuation Curves (78210257) Diagram I 0 10 20 824 – 846.5 30 869 – 891.5 0 2.5 60 3.0 70 3.5 80 4.0 90 4.5 840 850 860 870 880 890 900 Frequency/MHz 5.0 810 910 Typical Attenuation Curves (78210265) Diagram I 0 10 20 824 – 846.5 30 869 – 891.5 0 2.5 60 3.0 70 3.5 80 4.0 90 4.5 840 850 860 870 880 890 900 Frequency/MHz 910 880 890 900 Frequency/MHz 910 830 840 869 – 891.5 850 Antenna Low band 860 870 880 890 900 Frequency/MHz 910 High band Antenna 824 – 846.5 1.5 50 830 820 1.0 2.0 820 870 0.5 40 100 810 860 High band Antenna Diagram II High band Antenna Attenuation/dB Attenuation/dB Antenna Low band 850 824 – 846.5 1.5 50 830 840 Antenna Low band 1.0 2.0 820 830 0.5 40 100 810 820 869 – 896 Diagram II High band Antenna Attenuation/dB Attenuation/dB Antenna Low band 824 – 851 1.5 2.0 820 High band Antenna 0 40 100 810 Filters / Duplexers Duplexer Duplexer 824 824 –– 851 851 // 869 869 –– 896 896 MHz MHz (AMPS (AMPS A/B-Band) A/B-Band) 824 824 –– 846.5 846.5 // 869 869 –– 891.5 891.5 MHz MHz (AMPS (AMPS A/B-Band) A/B-Band) 5.0 810 820 830 840 869 – 891.5 850 860 870 880 890 900 Frequency/MHz 910 223 229 Duplexer Duplexer Duplexer 890 915 MHz (GSM) 890 –– 960 MHz (GSM) 890–––915 915/ /935 / 935 935 – 960 960 MHz (GSM) Duplexer The Duplexer is is designed to combine/split The combine/split 890 –and 915 /designed 935onto/from – toto 960 MHz (GSM) The Duplexer Duplexer is designed combine/split GSM Tx RxRx signals one GSM Tx and signals onto/from one GSM TxTx/Rx and Rx signals onto/from common antenna in order to saveone common Tx/Rx antenna in order to save common Tx/Rx antenna in order to save feeder cable and antenna costs. Duplexer feeder and 890 cable – 915 /antenna 935 costs. – 960 MHz (GSM) feeder cable and antenna costs. The Duplexer is designed to combine/split 782 10164: Indoor version with 7-16 female GSM Tx andIndoor Rx signals onto/from one connectors 782 78210164: 10164: Indoorversion versionwith with7-16 7-16female female connectors common Tx/Rx in 7-16/N order female to save connectors 782 10165: Indoorantenna version with feeder cableIndoor and antenna costs. connectors 782 10165: version with 7-16/N female 782 10164 (indoor) 782 10162 (outdoor) 782 78210162 10162(outdoor) (outdoor) 782Duplexer 10165: Indoor version withto7-16/N female The is designed combine/split connectors 782 10161: Indoor version with 7-16 female connectors GSM Tx and Rxversion signals onto/from 782 10164: Indoor 7-16 female one connectors mounted onto a with 19ß drawer connectors 782 Indoor version 7-16 78210161: 10161: Indoorantenna versionwith with 7-16female female common Tx/Rx in7-16 order to save 782 10162: Outdoor version with female connectors mounted onto aa19ß drawer connectors mounted onto 19ß drawer 782 10165: Indoor version with 7-16/N female feeder cable and antenna costs. connectors 782 78210164 10164(indoor) (indoor) 782 10164 (indoor) 782 10162 (outdoor) connectors 782 78210162: 10162:Outdoor Outdoorversion versionwith with7-16 7-16female female connectors 782 10161: version withwith 7-167-16 female connectors 782 10164:Indoor Indoor version female connectors mounted onto a 19ß drawer connectors 782 10161 (19ß drawer) 782 10162: Outdoor version with 7-16 female 782 10162 (outdoor) 782 10165: Indoor version with 7-16/N female Typical Attenuation Curves connectors 782 connectors 78210161 10161(19ß (19ßdrawer) drawer) Diagram I Diagram II 60 90 60 50 Typical Attenuation Curves 935 – 960 890 – 915 Diagram I Antenna → Low band High band → Antenna 3.0 1.0 4.0 2.0 4.5 2.5 0 70 5.0 100 3.0 60 70 10 875 885 895 905 915 925 935 945 955 965 975 875 80 3.5 70 Frequency/MHz 80 20 4.0 80 90 935 – 960 890 – 915 90 30 4.5 90 100 100 40 875 885 895 905 915 925 935 945 955 965 975 100 875 885 895 905 915 925 935 945 955 965 9755.0 Attenuation/dB 2.5 2.5 Technical Data 875 885 50 No. Type 895 905 915 925 935 935 – 960 890 – 915 Diagram II High band → Antenna 3.0 Antenna → Low band 3.0 0 782 3.5 3.5 0.5 895 905 915 925 935 945 955 965 975 885 4.0 Frequency/MHz 4.0 1.0 4.5 935 – 960 890 – 915 4.5 1.5 5.0 5.0 2.0 875 885 895 905 915 925 935 945 955 965 975 875 885 895 905 915 925 935 945 955 965 975 875 782 78210165 10165(indoor) (indoor) 10165 (indoor) Accessories (order separately) 885 2.5 895 915 925 935 945 Clamp Clamp set Type No. suitable for mast 10161 782 10162 782 10165 diameter of (indoor) Set Frequency/MHz 955 965 975 Frequency/MHz 782 10165 782 Frequency/MHz 905 3.0 Pass band 734 360 34 – 60 mm 3.5 70 Low band Data 890 – 915 MHz Technical Technical Data Technical High band Data 935 – 960 MHz 734 361 60 – 80 mm 4.0 80 Insertion loss Type No. Type No. Type No. 734 362 80 –782 100 mm 782 10164 782 10165 782 10161 10162 4.5 90 Antenna → Low band < 0.5 dB (890 – 915 MHz) High band → Antenna < 0.5 dB (935 – 960 MHz) Pass band 5.0 734 363 100 – 120 mm 100 band Pass Pass band Isolation 875 band 885 895 905 915 925 935 945 955 965 975 875 885 895 905 915 935 MHz 945 955 MHz 965 975 Low band 890 ––915 Low 890925 – 915 Lowband band↔ High band 915 MHz Low > 70 dB (890 – 915 /890 935 –960 960 MHz MHz) 734 364 120 – 140 mm Frequency/MHz Frequency/MHz High band 935 – High band 935 – 960 MHz High band 935 – 960 MHz VSWR < 1.25 (890 – 915 / 935 – 960 MHz) Insertion loss Insertion loss 734 365 45 – 125 mm Insertion loss Impedance 50 dB Antenna →→Low band < 0.5 dB< (890 – 915 MHz) Antenna Low 0.5 (890 ––915 Antenna → Lowband band <(935 0.5 –dB (890 915MHz) MHz) High band → Antenna < 0.5 dB 960 MHz) Input power < 500 W (high band; with max. 16 carriers) High → <<0.5 Technical Data Highband band →Antenna Antenna 0.5dB dB(935 (935––960 960MHz) MHz) Isolation Intermodulation products < –160 dBc (3rd order; with 2 x 20 W) Isolation Isolation Low band ↔ High band > 70 dB (890 – 915 / 935 – 960 MHz) Type No. range Low 70 (890 ––915 / 935 ––960 MHz) Temperature –20 ... +55>>°C –40 ... +60 °C Lowband band↔ ↔High Highband band 70dB (890 915 VSWR < 1.25 (890 –dB 915 / 935 – 960/ 935 MHz) 960 MHz) Connectors VSWR <<1.25 (890 ––915 //935 ––960 MHz) VSWR 1.25 (890 915 935 960 MHz) Impedance 50 Pass Lowband band 7-16 female N female 7-16 female 7-16 female Impedance High band 7-16 female 7-16 female 7-16 female Low band 890max. –50 915 Impedance 50 MHz Input power <7-16 500 female W (high band; with 16 carriers) Antenna 7-16 female 7-16 female 7-16 female 7-16 female High band products 935 – 960 MHz Input power <<500 (high band; with max. Intermodulation < –160 dBcW (3rd order; with 2with x 20 W) 16 Input power 500 W (high band; max. 16carriers) carriers) Application Indoor Indoor Indoor, 19ß drawer Outdoor (IP 66) Insertion loss Intermodulation products < –160 dBc (3rd order; with 2 x 20 W) Temperature rangeproducts –20 ... +55 –40 ... +60 °C Intermodulation < °C –160 dBc (3rd order; with 2 x 20 W) Special featuresrange Built-in DC stop between all ports Antenna → Low band < 0.5 dB (890 – 915 MHz) Temperature –20 ... +55 °C –40 Connectors Temperature range –20 ... +55 °C –40... ...+60 +60°C °C High band → Antenna < 0.5 dB (935 – 960 MHz) Mounting With 4 screws With 4 screws Wall mounting: With 4 screws Low band 7-16 female N female 7-16 female female Connectors 782 10164 (max. 7-16 8 mm diameter) (max. 4 mm diameter) (max. 6 mm diameter) Connectors High band 7-16 female 7-16 female 7-16 female 7-16 female Isolation Low band female NNfemale 7-16 female 7-16 Mast mounting: With additioAntenna 7-167-16 female 7-16 female 7-16 female 7-16 female Low 7-16 female female 7-16 female 7-16female female Low band band ↔ High band > 70 dB (890 – 915 / 935 –(indoor) 960 MHz) High 7-16 7-16 7-16 nal clamp set 7-16 Highband band 7-16female female 7-16female female 7-16female female Outdoor 7-16female female Application Indoor Indoor Indoor, 19ß drawer (IP 66) Antenna 7-16 female 7-16 female 7-16 female 7-16 female VSWR < 1.25 (890 – 915 / 935 – 960 MHz) Weight 2.6 kg 3.5 kg 7-16 female 5.5 kg Antenna 7-16 female 7-16 female 7-16 female Special features Built-in DC stop between all ports Application Indoor Indoor Indoor, 19ß drawer Outdoor Impedance mm Packing size 309Indoor mm x 162 mm x 252 mm x 312 x 224 mm 347 mm x 294 mm xOutdoor 174 mm (IP 66) Application Indoor 612 mm50 Indoor, 19ß drawer Mounting With 4 screws With 4 screws Wall mounting: With 4 screws (IP 66) 229 Special features Built-in DC stop between all ports Input power < 500 W (high band; with max. 16 carriers) Dimensions (w x h x d) 228.6 mm x 80 mm x 169.6 mm 19ß drawer, 2 height units, 238 mm x 93.5 mm x 305 (max. 8 mm diameter)mm (max. 4 mm diameter) 6 mm diameter) Special features Built-in DC (max. stop between all ports 219 (including connectors and mounting feet) plug-in depth 172 (including connectors and Mast mounting: With additioMounting With With screws Wall mounting: With 44screws Intermodulation products 2mm x4420 W) Mounting With44screws screws < –160 dBc (3rd order; with With screws Wall mounting: screws mounting brackets) nal clamp set 8 mm With (max. diameter) (max. 4 mm diameter) (max. 6 mm diameter) (max. mm+60 diameter) (max. 4 mm diameter) (max. 6 mm diameter) Temperature range –20 ... +55 °C –408 ... °C Weight 2.6 kg 3.5 kg 5.5 kg mounting: With additioMast Mast mounting: With additioConnectors nal mm clamp set Packing size 309 mm x 162 mm x 252 mm 612 mm x 312 mm x 224 mm 347 mm x 294 mm x 174 set 782 10161, 782 10162, 782 10164, 782 10165 Page 1nal of clamp 2 female Low band 7-16 female N female 7-16 female 7-16 Internet: http://www.kathrein.de Weight 2.6 kg 3.5 kg 5.5 kg Dimensions (w x h x d) 228.6 mm x 80 mm x 169.6 mm 19ß drawer, 2 height units, 238 mm x 93.5 mm x 305 mm Weight 2.6 kg 3.5 kg 5.5female kg High band 7-16 female and. mounting feet) 7-16 female 7-16 female 7-16 . . . . . (including connectors plug-in depth 172 mm (including connectors and KATHREIN-Werke KG Anton-Kathrein-Straße 1 –7-16 3 309 PO Box 10 04 44 mm D-83004 Rosenheim Germany Telephone +49 8031 1 84-0 Fax +49 8031 1 84-9 91 mm x 174 mm Packing size mm mm 612 mm mm mm Antenna female 7-16 Packing size 309 mmxx162 162 mmxx252 252 mmfemale 612mm mmx7-16 x312 312female mmxx224 224 mm 347 347 mmx7-16 x294 294female mm x 174 mm mounting brackets) 782 782 10164 10164 782 782 10165 10165 782 782 10161 10161 782 782 10162 10162 782 10164 782 10165 782 10161 782 10162 169.6 936.2277/b Subject alteration. 936.2277/b Subject to alteration. Subject to936.2277/b alteration. Subject totoalteration. 936.2277/b Subject to alteration. 782 10164 Frequency/MHz 60 936.2277/b Frequency/MHz 945 955 965 975 Frequency/MHz Duplexer 782 10165 (indoor) 890 – 915 / 935 – 960 MHz (GSM) 935 – 960 89010161 – 915 782 (19ß drawer) 935 – 960 890 – 915 1.5 1.5 2.0 2.0 3.5 1.5 High band → Antenna 782 1 (indo 175.2 50 50 80 40 2.5 0.5 1.0 1.0 .3 40 40 70 30 935 – 960 935 – 960 890 – 915 890 – 915 30 30 60 20 0.5 Antenna → Low band 0.5 2.00 ø4 50 10 1.5 6 20 20 Antenna Antenna→ →Low Lowband band High Highband band→ →Antenna Antenna 0 0 935 – 960 890II – 915 Diagram 76.1 High band → Antenna Diagram II 134 148 → Low band 400 High band → Antenna 782 10161 II(19ß drawer) Diagram Attenuation/dB Attenuation/dB 10 Antenna 10 935 – 960 Antenna → Low band Attenuation/dB 30 Diagram 890I– 915 Attenuation/dB 0 Attenuation/dB Attenuation/dB Attenuation/dB Attenuation/dB Attenuation/dB 782 10161: Indoor with 7-16 female Antenna → Low band version High band → Antenna Typical Attenuation Curves Typical Attenuation 0 0 connectors mounted onto a 19ßCurves drawer Diagram II Diagram 0.5 10 782Antenna 10162: Outdoor versionCurves with → 7-16 female Low Typical Antenna→ →Attenuation Lowband band High Highband band →Antenna Antenna 1.0 20 connectors 0 782 10164 (indoor) Dimensions Application Dimensions(w (wxxhhxxd) d) Special features Internet: http://www.kathrein.de Mounting 228.6 mm 19ß units, xx93.5 305 Indoor Indoor, drawer Outdoor (IPxx66) 228.6mm mmxx80 80mm mmxx169.6 169.6Indoor mm 19ßdrawer, drawer,219ß 2height height units, 238 238mm mm 93.5mm mm 305mm mm (including feet) plug-in (including (includingconnectors connectorsand andmounting mounting feet) plug-in depth 172mm mm (includingconnectors connectorsand and Built-in DC stop between alldepth ports172 mounting 782 10161, 782 10162, 782 10164, 782 10165 Page 1 of 2 brackets) mounting brackets) With 4 screws With 4 screws Wall mounting: With 4 screws (max. 8 mm diameter) (max. 4 44 mm diameter) (max.+49 6 mm . D-83004 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 Rosenheim . Germany . Telephone 8031diameter) 15084-0 . Fax 27.5 +49 8031 59.5 1 84-9 91 91.5 max. 80 Mast mounting: With additio206 782 10161, 782 10162, 782 10164, 782 10165 Page 11band of Internet: http://www.kathrein.de nal clamp set Low band Antenna High 782 10161, 782 10162, 782 10164, 782 10165 Page of22 Internet: http://www.kathrein.de Weight 2.6 kg 3.5 kg 5.5 kg . . . . . . KATHREIN-Werke KATHREIN-WerkeKG KG . Anton-Kathrein-Straße Anton-Kathrein-Straße11––33 . PO POBox Box10 1004 0444 44 . D-83004 D-83004Rosenheim Rosenheim . Germany Germany . Telephone Telephone+49 +498031 80311184-0 84-0 . Fax Fax+49 +498031 80311184-9 84-991 91 note: Packing size 309 mm x 162 mm x 252 mm 612 Please mm x 312 mm x 224 mm 347 mm x 294 mm x 174 mm Type 782 10162 (outdoor version): IP66 protection will be lost, and all Dimensions (w x h x d) 228.6 mm x 80 mm x 169.6 mm 19ßcorresponding drawer, 2 height units, 238 mm x 93.5 mm x 305 mm guarantees will become null and void, if mounting (including connectors and mounting feet) plug-in depth 172 mm (including connectors and brackets are removed or tampered with. This type is designed to opermounting brackets) ate under the environmental conditions as described in 224 Internet: http://www.kathrein.de ETS 300 019-1-4 class 4.1 E and has passed environmental tests as recommended in ETS 300 019-2-4. 782 10161, 782 10162, 782 10164, 782 10165 Page 1 of 2 As a result of more stringent legal regulations and judgements . Telephone . Fax KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany +49liability, 8031 1 we 84-0 +49 to 8031 1 84-9 regarding product are obliged point out 91 certain 782 (ou Duplexer 880 – 915 / 925 – 960 MHz (EGSM) The Duplexer is designed to combine/split EGSM Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor applications • Built-in DC Stop Typical Attenuation Curves Diagram I Attenuation/dB Antenna → Low band High band → Antenna 0 10 20 880 – 915 925 – 960 30 40 50 Low band Antenna 60 High band 70 Technical Data Subject to alteration. Pass band Low band High band Insertion loss Antenna → Low band High band → Antenna Isolation Low band ↔ High band VSWR Input power < 250 W (low band or high band) Connectors Application Special features Mounting 936.2305/c > 75 dB (880 – 915 / 925 – 960 MHz) < 1.25 (880 – 915 / 925 – 960 MHz) Weight Packing size Dimensions (w x h x d) Internet: http://www.kathrein.de 880 890 900 910 920 930 940 950 960 970 Frequency/MHz Diagram II < 0.9 dB (880 – 915 MHz) < 0.9 dB (925 – 960 MHz) 50 Temperature range 100 870 880 – 915 MHz 925 – 960 MHz Impedance Intermodulation products 90 782 10167 Antenna → Low band Attenuation/dB Type No. 80 High band → Antenna 0 0.5 1.0 880 – 915 925 – 960 1.5 < –160 dBc (3rd order; with 2 x 20 W) 2.0 –20 … +55 °C 2.5 7-16 female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 4.6 kg 347 mm x 297 mm x 174 mm 229 mm x 81 mm x 260 mm (including connectors and mounting feet) 3.0 3.5 4.0 4.5 5.0 870 880 890 900 910 920 930 940 950 960 970 Frequency/MHz 782 10167 Page 1 of 1 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 225 Duplexer Duplexer 1710 1710 –– 1785 1785 // 1805 1805 –– 1880 1880 MHz MHz (GSM (GSM 1800) 1800) The Duplexer is designed to combine/split GSM 1800 Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor applications • Built-in DC stop between all ports 792542 78210415 Low band Antenna High band Low Band Antenna High Band Typical Attenuation Curves Attenuation/dB Diagram I 0 Antenna Low band High band Antenna 10 20 30 1805 – 1880 1710 – 1785 40 50 60 Technical Data Pass band Low band High band Insertion loss Antenna Low band High band Antenna Isolation Low band High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency Mounting Weight Packing size Dimensions (w x h x d) 226 232 792542 80 78210415 90 100 1710 – 1785 MHz 1805 – 1880 MHz 1695 1715 1735 1755 1775 1795 < 0.7 dB (1710 – 1785 MHz) < 0.7 dB (1805 – 1880 MHz) > 65 dB (1710 – 1785 / 1805 – 1880 MHz) < 1.25 (1710 – 1785 / 1805 – 1880 MHz) 50 Ω < 250 W (low band or high band, with max. 8 carriers) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C 7-16 female Indoor Indoor, 19˝ drawer Built-in DC stop between all ports With 4 screws With 4 screws (max. 4 mm diameter) (max. 6 mm diameter) 1.6 kg 2.6 kg 282 x 252 x 114 mm 612 x 312 x 224 mm 192 x 42.5 x 199.6 mm 19˝ drawer, 2 height units (including connectors plug-in depth 184 mm and mounting feet) Diagram II Attenuation/dB Type No. 70 0 Antenna Low band 1815 1835 1855 1875 1895 Frequency/MHz High band Antenna 0.5 1.0 1.5 1710 – 1785 1805 – 1880 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1695 1715 1735 1755 1775 1795 1815 1835 1855 1875 1895 Frequency/MHz Filters / Duplexers Duplexer Duplexer 1850 –– 1910 1850 1910 // 1930 1930 –– 1990 1990 MHz MHz (GSM (GSM 1900) 1900) The Duplexer is designed to combine/split GSM 1900 Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor applications • Built-in DC stop Typical Attenuation Curves Low Band Antenna High Band Attenuation/dB Diagram I Antenna Low band 0 High band Antenna 10 20 30 1850 – 1910 1930 – 1990 40 50 60 70 Technical Data Pass band Low band High band Insertion loss Antenna Low band High band Antenna Isolation Low band High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 90 792544 100 1820 1840 1860 1880 1900 1920 1940 1960 1980 2000 2020 Frequency/MHz 1850 – 1910 MHz 1930 – 1990 MHz < 0.7 dB (1850 – 1910 MHz) < 0.7 dB (1930 – 1990 MHz) > 65 dB (1850 – 1910 / 1930 – 1990 MHz) < 1.25 (1850 – 1910 / 1930 – 1990 MHz) 50 Ω < 300 W (low band or high band) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C 7-16 female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 1.7 kg 282 x 252 x 114 mm 192 x 42.5 x 199.6 mm (including connectors and mounting feet) Diagram II Attenuation/dB Type No. 80 0 Antenna Low band High band Antenna 0.5 1.0 1.5 1850 – 1910 1930 – 1990 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1820 1840 1860 1880 1900 1920 1940 1960 1980 2000 2020 Frequency/MHz 233 227 Duplexer Duplexer 1920 1980 // 2110 2110 –– 2170 2170 MHz MHz (UMTS) (UMTS) 1920 – – 1980 The Duplexer is designed to combine/split UMTS Tx and Rx signals onto/from one common Tx/Rx antenna in order to save feeder cable and antenna costs. • Suitable for indoor applications • Built-in DC stop 78210193 78210192 Low band Antenna High band Typical Attenuation Curves Diagram I Low band Antenna Attenuation/dB Antenna Low band High band High band Antenna 0 10 20 30 2110 – 2170 1920 – 1980 40 50 Technical Data Pass band Low band High band Insertion loss Antenna Low band High band Antenna Isolation Low band High band VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 228 234 78210192 78210193 70 80 1920 – 1980 MHz 2110 – 2170 MHz < 0.3 dB (1920 – 1980 MHz) < 0.3 dB (2110 – 2170 MHz) 90 100 1800 1850 1900 1950 2000 2050 > 90 dB (1920 – 1980 / 2110 – 2170 MHz) < 1.25 (1920 – 1980 / 2110 – 2170 MHz) 50 Ω < 250 W (low band or high band) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +55 °C 7-16 female N female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 1.67 kg 272 x 237 x 119 mm 229 x 46 x 167.6 mm 229 x 46 x 173.4 mm (including connectors and mounting feet) Diagram II Attenuation/dB Type No. 60 0 Antenna Low band 2100 2150 2200 2250 2300 Frequency/MHz High band Antenna 0.5 1.0 1.5 1920 – 1980 2110 – 2170 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1800 1850 1900 1950 2000 2050 2100 2150 2200 2250 2300 Frequency/MHz Multiband Combiners Dual-Band Combiners Triple-Band Combiners Quad-Band Combiners 229 Summary of Multiband Combiner Types Multiband Combiners: Description Unit Type No. Frequency range By-pass Dual-Band Combiner Single 728954 Band 1: Band 2: 68 – 470 MHz 870 – 970 MHz Band 1: By-pass Band 2: Stop Dual-Band Combiner Single 78210341 Band 1: Band 2: 824 – 880 MHz 890 – 960 MHz Dual-Band Combiner Single 791145 Band 1: Band 2: Dual-Band Combiner Single 78210264 Dual-Band Combiner Single Dual-Band Combiner Max. input power Page 50 W 50 W 234 Band 1: Stop Band 2: Stop 400 W 400 W 235 50 – 1000 MHz 1600 – 2000 MHz Band 1: By-pass Band 2: Stop 100 W 50 W 236 Band 1: Band 2: 1710 - 2180 MHz 2400 – 2500 MHz Band 1: By-pass Band 2: Stop 200 W 200 W 237 78210460 Band 1: Band 2: 50 – 470 MHz 806 – 2500 MHz Band 1: By-pass Band 2: Stop 500 W 500 W 238, 239 Single 78210457 Band 1: Band 2: 87.5 – 470 MHz 806 – 2500 MHz Band 1: By-pass Band 2: By-pass 500 W 500 W 238, 239 Dual-Band Combiner Single 78210458 Band 1: Band 2: 87.5 – 470 MHz 806 – 2500 MHz Band 1: Stop Band 2: By-pass 500 W 500 W 238, 239 Dual-Band Combiner Single 78210970 Band 1: Band 2: 790 – 862 MHz 880 – 960 MHz Band 1: By-pass Band 2: By-pass 200 W 200 W 240, 241 Dual-Band Combiner Double 78210971 Band 1: Band 2: 790 – 862 MHz 880 – 960 MHz Band 1: By-pass Band 2: By-pass 200 W 200 W 240, 241 Dual-Band Combiner Single 78210972 Band 1: Band 2: 790 – 862 MHz 880 – 960 MHz Band 1: Stop Band 2: By-pass 200 W 200 W 240, 241 Dual-Band Combiner Double 78210973 Band 1: Band 2: 790 – 862 MHz 880 – 960 MHz Band 1: Stop Band 2: By-pass 200 W 200 W 240, 241 Dual-Band Combiner Single 78210974 Band 1: Band 2: 790 - 862 MHz 880 - 960 MHz Band 1: By-pass Band 2: Stop 200 W 200 W 240, 241 Dual-Band Combiner Double 78210975 Band 1: Band 2: 790 - 862 MHz 880 - 960 MHz Band 1: By-pass Band 2: Stop 200 W 200 W 240, 241 Dual-Band Combiner Double 78210979 Band 1: Band 2: 790 - 862 MHz 880 - 960 MHz Unit 1: Unit 2: Band 1: By-pass Band 1: Stop Band 2: Stop Band 2: By-pass 200 W 200 W Dual-Band Combiner Single 78210660 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz Band 1: By-pass Band 2: By-pass 650 W 350 W 244, 245 Dual-Band Combiner Double 78210661 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz Band 1: By-pass Band 2: By-pass 650 W 350 W 244, 245 Dual-Band Combiner Single 78210662 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz Band 1: Stop Band 2: By-pass 650 W 350 W 244, 245 Dual-Band Combiner Double 78210663 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz Band 1: Stop Band 2: By-pass 650 W 350 W 244, 245 Dual-Band Combiner Single 78210664 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz Band 1: By-pass Band 2: Stop 650 W 350 W 244, 245 Dual-Band Combiner Double 78210665 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz Band 1: By-pass Band 2: Stop 650 W 350 W 244, 245 Dual-Band Combiner Double 78210669 Band 1: Band 2: 470 – 960 MHz 1710 – 2700 MHz Unit 1: Unit 2: Band 1: By-pass Band 1: Stop Band 2: Stop Band 2: By-pass 650 W 350 W Dual-Band Combiner Single 78210680 Band 1: Band 2: 380 – 960 MHz 1710 – 2700 MHz Band 1: By-pass Band 2: By-pass 700 W 650 W 248, 249 Dual-Band Combiner Double 78210681 Band 1: Band 2: 380 – 960 MHz 1710 – 2700 MHz Band 1: By-pass Band 2: By-pass 700 W 650 W 248, 249 Dual-Band Combiner Single 78210682 Band 1: Band 2: 380 – 960 MHz 1710 – 2700 MHz Band 1: Stop Band 2: By-pass 700 W 650 W 248, 249 Dual-Band Combiner Double 78210683 Band 1: Band 2: 380 – 960 MHz 1710 – 2700 MHz Band 1: Stop Band 2: By-pass 700 W 650 W 248, 249 Dual-Band Combiner Single 78210278 Band 1: Band 2: 790 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: By-pass 500 W 500 W 250, 251 Dual-Band Combiner Double 78210279 Band 1: Band 2: 790 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: By-pass 500 W 500 W 250, 251 Dual-Band Combiner Single 78210305 Band 1: Band 2: 790 – 1880 MHz 1920 – 2170 MHz Band 1: Stop Band 2: By-pass 500 W 500 W 250, 251 Dual-Band Combiner Double 78210306 Band 1: Band 2: 790 – 1880 MHz 1920 – 2170 MHz Band 1: Stop Band 2: By-pass 500 W 500 W 250, 251 Dual-Band Combiner Single 78210620 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: By-pass 300 W 300 W 252, 253 Dual-Band Combiner Double 78210621 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: By-pass 300 W 300 W 252, 253 Dual-Band Combiner Single 78210622 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz Band 1: Stop Band 2: By-pass 300 W 300 W 252, 253 Dual-Band Combiner Double 78210623 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz Band 1: Stop Band 2: By-pass 300 W 300 W 252, 253 Dual-Band Combiner Single 78210624 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: Stop 300 W 300 W 252, 253 230 242, 243 246, 247 Summary of Multiband Combiner Types Multiband Combiners: Description Unit Type No. Dual-Band Combiner Double 78210625 Dual-Band Combiner Double 78210626 Dual-Band Combiner Single Dual-Band Combiner Frequency range By-pass Max. input power Page Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: Stop 300 W 300 W 252, 253 Band 1: Band 2: 1710 – 1880 MHz 1920 – 2170 MHz Unit 1: Unit 2: Band 1: By-pass Band 1: Stop Band 2: Stop Band 2: By-pass 300 W 300 W 78210469 Band 1: Band 2: 1850 – 1990 MHz 1710 – 2155 MHz DC switchable 250 W 250 W 256 Double 78210808 Band 1: Band 2: 1850 – 1990 MHz 1710 – 2155 MHz DC switchable 250 W 250 W 256 Dual-Band Combiner Single 78210809 Band 1: Band 2: 1850 – 1990 MHz 1710 – 2155 MHz Band 1: By-pass Band 2: By-pass 250 W 250 W 257 Dual-Band Combiner Double 78210810 Band 1: Band 2: 1850 – 1990 MHz 1710 – 2155 MHz Band 1: By-pass Band 2: By-pass 250 W 250 W 257 Dual-Band Combiner Single 78210800 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz Band 1: By-pass Band 2: By-pass 300 W 300 W 258, 259 Dual-Band Combiner Double 78211091 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz Band 1: By-pass Band 2: By-pass 300 W 300 W 258, 259 Dual-Band Combiner Single 78211092 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz Band 1: Stop Band 2: By-pass 300 W 300 W 258, 259 Dual-Band Combiner Double 78211093 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz Band 1: Stop Band 2: By-pass 300 W 300 W 258, 259 Dual-Band Combiner Single 78211094 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz Band 1: By-pass Band 2: Stop 300 W 300 W 258, 259 Dual-Band Combiner Double 78211095 Band 1: Band 2: 1710 – 2180 MHz 2400 – 2700 MHz Band 1: By-pass Band 2: Stop 300 W 300 W 258, 259 Dual-Band Combiner Double 78211099 Band 1: Band 2: 1710 – 2180 MHz 2400 - 2700 MHz Unit 1: Unit 2: Band 1: By-pass Band 1: Stop Band 2: Stop Band 2: By-pass 300 W 300 W Dual-Band Combiner Single 78211180 Band 1: Band 2: 690 - 2180 MHz 2400 - 2700 MHz Band 1: By-pass Band 2: By-pass 500 W 500 W 262, 263 Dual-Band Combiner Double 78211181 Band 1: Band 2: 690 - 2180 MHz 2400 - 2700 MHz Band 1: By-pass Band 2: By-pass 500 W 500 W 262, 263 Dual-Band Combiner Single 78211182 Band 1: Band 2: 690 - 2180 MHz 2400 - 2700 MHz Band 1: Stop Band 2: By-pass 500 W 500 W 262, 263 Dual-Band Combiner Double 78211183 Band 1: Band 2: 690 - 2180 MHz 2400 - 2700 MHz Band 1: Stop Band 2: By-pass 500 W 500 W 262, 263 Dual-Band Combiner Single 78211184 Band 1: Band 2: 380 - 2180 MHz 2400 - 2700 MHz Band 1: By-pass Band 2: Stop 500 W 500 W 262, 263 Dual-Band Combiner Double 78211185 Band 1: Band 2: 380 - 2180 MHz 2400 - 2700 MHz Band 1: By-pass Band 2: Stop 500 W 500 W 262, 263 Triple-Band Combiner Single 78210630 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: By-pass Band 3: By-pass 700 W 300 W 300 W 264, 265 Triple-Band Combiner Double 78210631 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: By-pass Band 3: By-pass 700 W 300 W 300 W 264, 265 Triple-Band Combiner Single 78210632 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz Band 1: Stop Band 2: Stop Band 3: By-pass 700 W 300 W 300 W 264, 265 Triple-Band Combiner Double 78210633 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz Band 1: Stop Band 2: Stop Band 3: By-pass 700 W 300 W 300 W 264, 265 Triple-Band Combiner Single 78210634 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: Stop Band 3: Stop 700 W 300 W 300 W 264, 265 Triple-Band Combiner Double 78210635 Band 1: Band 2: Band 3: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz Band 1: By-pass Band 2: Stop Band 3: Stop 700 W 300 W 300 W 264, 265 Triple-Band Combiner Single 78211130 Band 1: Band 2: Band 3: 710 – 960 MHz 1710 – 2180 MHz 2490 – 2690 MHz Band 1: By-pass Band 2: By-pass Band 3: By-pass 300 W 300 W 300 W 266, 267 Triple-Band Combiner Double 78211131 Band 1: Band 2: Band 3: 710 – 960 MHz 1710 – 2180 MHz 2490 – 2690 MHz Band 1: By-pass Band 2: By-pass Band 3: By-pass 300 W 300 W 300 W 266, 269 Triple-Band Combiner Single 78211132 Band 1: Band 2: Band 3: 710 – 960 MHz 1710 – 2180 MHz 2490 – 2690 MHz Band 1: Stop Band 2: Stop Band 3: By-pass 300 W 300 W 300 W 266, 267 Triple-Band Combiner Double 78211133 Band 1: Band 2: Band 3: 710 – 960 MHz 1710 – 2180 MHz 2490 – 2690 MHz Band 1: Stop Band 2: Stop Band 3: By-pass 300 W 300 W 300 W 266, 267 Triple-Band Combiner Single 78211134 Band 1: Band 2: Band 3: 790 - 960 MHz 1710 - 2180 MHz 2490 - 2690 MHz Band 1: Stop Band 2: By-pass Band 3: Stop 300 W 300 W 300 W 266, 267 254, 255 260, 261 231 Summary of Multiband Combiner Types Multiband Combiners: Description Triple-Band Combiner Double 78211135 Band 1: Band 2: Band 3: 790 - 960 MHz 1710 - 2180 MHz 2490 - 2690 MHz Band 1: Stop Band 2: By-pass Band 3: Stop 300 W 300 W 300 W 266, 267 Triple-Band Combiner Single 78211190 Band 1: Band 2: Band 3: 791 - 862 MHz 880 - 960 MHz 1710 - 2690 MHz Band 1: By-pass Band 2: By-pass Band 3: By-pass 300 W 300 W 300 W 268, 269 Triple-Band Combiner Double 78211191 Band 1: Band 2: Band 3: 791 - 862 MHz 880 - 960 MHz 1710 - 2690 MHz Band 1: By-pass Band 2: By-pass Band 3: By-pass 300 W 300 W 300 W 268, 269 Triple-Band Combiner Single 78211192 Band 1: Band 2: Band 3: 791 - 862 MHz 880 - 960 MHz 1710 - 2690 MHz Band 1: Stop Band 2: Stop Band 3: By-pass 300 W 300 W 300 W 268, 269 Triple-Band Combiner Double 78211193 Band 1: Band 2: Band 3: 791 - 862 MHz 880 - 960 MHz 1710 - 2690 MHz Band 1: Stop Band 2: Stop Band 3: By-pass 300 W 300 W 300 W 268, 269 Quad-Band Combiner Single 78210640 Band 1: Band 2: Band 3: Band 4: 380 – 960 MHz 1710 – 1880 MHz 920 – 2200 MHz 2500 – 2690 MHz Band 1: By-pass Band 2: By-pass Band 3: By-pass Band 4: By-pass 700 W 300 W 300 W 200 W 270, 271 Quad-Band Combiner Double 78210641 Band 1: Band 2: Band 3: Band 4: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2200 MHz 2500 – 2690 MHz Band 1: By-pass Band 2: By-pass Band 3: By-pass Band 4: By-pass 700 W 300 W 300 W 200 W 270, 271 Quad-Band Combiner Single 78210642 Band 1: Band 2: Band 3: Band 4: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2200 MHz 2500 – 2690 MHz Band 1: Stop Band 2: Stop Band 3: Stop Band 4: By-pass 700 W 300 W 300 W 200 W 270, 271 Quad-Band Combiner Double 78210643 Band 1: Band 2: Band 3: Band 4: 380 – 960 MHz 1710 – 1880 MHz 1920 – 2200 MHz 2500 – 2690 MHz Band 1: Stop Band 2: Stop Band 3: Stop Band 4: By-pass 700 W 300 W 300 W 200 W 270, 271 Quad-Band Combiner Single 78210644 Band 1: Band 2: Band 3: Band 4: 380 - 960 MHz 1710 - 1880 MHz 1920 - 2200 MHz 2500 - 2690 MHz Band 1: Stop Band 2: Stop Band 3: By-pass Band 4: Stop 700 W 300 W 300 W 200 W 270, 271 Quad-Band Combiner Double 78210645 Band 1: Band 2: Band 3: Band 4: 380 - 960 MHz 1710 - 1880 MHz 1920 - 2200 MHz 2500 - 2690 MHz Band 1: Stop Band 2: Stop Band 3: By-pass Band 4: Stop 700 W 300 W 300 W 200 W 270, 271 Quad-Band Combiner Double 78210649 Band 1: Band 2: Band 3: Band 4: 380 - 960 MHz 1710 - 1880 MHz 1920 - 2200 MHz 2500 - 2690 MHz Unit 1 Band 1: Stop Band 2: Stop Band 3: By-pass Band 4: Stop SmartPlex Dual-Band Combiner Double 78210900 Band 1: Band 2: 380 – 960 MHz 1710 – 2690 MHz Auto sense 500 W 300 W 274, 275 SmartPlex Dual-Band Combiner Double 78210901 Band 1: Band 2: 380 – 960 MHz 1710 – 2690 MHz Auto sense 500 W 300 W 274, 275 232 By-pass Page Type No. New Products Frequency range Max. input power Unit Unit 2: Band 1: Stop Band 2: Stop Band 3: Stop Band 4: By-pass 700 W 300 W 300 W 200 W 272, 273 Multiband Combiner – Frequency combinations Dual-Band Combiner, Triple-Band Combiner, Quad-Band Combiner 233 Band-pass Filter Dual-Band Combiner 80168–– 862 MHz 470 MHz 870 – 970 MHz 80 / 160 / 400 MHz GSM 900 • Designed for inhouse multiband distribution network Port 1 • Enables feeder sharing • DC by-pass between port 1 and port 3 • Built-in DC stop between port 2 and port 3 Port 2 Port 3 ø4.3 Output N coupler 40 105 111.6 Input N coupler Input N coupler 223 229.4 Typical Attenuation Curves Port 3 Port 1 68 – 470 MHz Port 2 870 – 970 MHz Attenuation/dB Diagram I Intermodulation products Temperature range Connectors Application DC transparency Port 1 Port 3 Port 2 Port 3 Port 3 Port 2 Weight Packing size Dimensions (w x h x d) 234 68 – 470 870 – 970 10 20 30 50 728954 60 70 68 – 470 MHz 870 – 970 MHz 80 90 < 0.5 dB (68 – 470 MHz) < 0.5 dB (870 – 970 MHz) > 45 dB < 1.2 50 Ω < 50 W < 50 W < –160 dBc (2 nd/3 rd order; with 2 x 20 W) –20 ... +70 °C N female Indoor By-pass (max. 2500mA) short circuited stop 0.8 kg 285 x 55 x 125 mm 229.4 x 32 x 111.6 mm (without connectors) 100 0 100 200 300 400 500 600 0 700 800 900 Frequency/MHz Diagram II Attenuation/dB Pass band Band 1 Band 2 Insertion loss Port 1 Port 3 Port 2 Port 3 Isolation Port 1 Port 2 VSWR Impedance Input power Band 1 Band 2 Port 2 Port 3 40 Technical Data Type No. Port 1 Port 3 0 1000 Port 1 Port 3 Port 2 Port 3 68 – 470 870 – 970 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 100 200 300 400 500 600 700 800 900 Frequency/MHz 1000 239 Multiband Combiners 12 15 32 18.7 Dual-Band Combiner 824 – 880 MHz AMPS / CDMA 850 890 – 960 MHz GSM 900 • Designed for co-siting purposes • Enables feeder sharing • Suitable for indoor applications • Built-in DC stop between all ports Port 1 Multiband Combiners Port 3 Port 2 Typical Attenuation Curves Diagram I Attenuation/dB Port 1 Port 3 Port 2 Port 3 0 10 20 890 – 960 824 – 880 30 40 50 Technical Data Pass band Band 1 (AMPS / CDMA 800) Band 2 (GSM 900) Insertion loss Port 1 Port 3 Port 2 Port 3 Isolation Port 1 Port 2 VSWR Impedance Input power Band 1 Band 2 Intermodulation products Temperature range Connectors Application Special features Mounting Weight Dimensions (w x h x d) 78210341 70 824 – 880 MHz 890 – 960 MHz 90 80 100 800 < 0.6 dB (824 – 880 MHz) < 0.6 dB (890 – 960 MHz) > 55 dB (824 – 880 / 890 – 960 MHz) < 1.2 (824 – 880 / 890 – 960 MHz) 50 Ω < 400 W (with max. 8 carriers) < 400 W (with max. 8 carriers) < –160 dBc (3 rd order; with 2 x 20 W) –20 ... +55 °C 7-16 female Indoor Built-in DC stop between all ports With 4 screws (max. 4 mm diameter) 3.2 kg 228 x 85 x 199.3 mm (including connectors and mounting feet) 820 840 860 880 900 Diagram II Attenuation/dB Type No. 60 0 Port 1 Port 3 920 940 960 980 1000 980 1000 Frequency/MHz Port 2 Port 3 0.5 1.0 890 – 960 824 – 880 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 800 820 840 860 880 900 920 940 960 Frequency/MHz 235 243 Dual-Band Combiner 50 – 1000 MHz 80 / 160 / 400 / GSM 900 1600 – 2000 MHz GSM 1800 • Designed for inhouse multiband distribution network • Enables feeder sharing • DC by-pass between port 1 and port 3 • Built-in DC stop between port 2 and port 3 Port 1 Port 2 Port 3 deep Port 3 Port 1 Port 2 50 – 1000 MHz 1600 – 2000 MHz Typical Attenuation Curves Diagram I Attenuation/dB Port 1 Port 3 VSWR (all ports) Impedance Input power Band 1 Band 2 Temperature range Connectors Application DC transparency Port 1 Port 3 Port 2 Port 3 Port 3 Port 2 Mounting Weight Packing size Dimensions (w x h x d) 236 242 20 1600 – 2000 50 – 1000 30 50 791145 60 70 50 – 1000 MHz 1600 – 2000 MHz 80 < 0.3 dB (50 – 1000 MHz) < 0.5 dB (1600 – 2000 MHz) 100 90 0 > 40 dB (50 – 1000 / 1600 – 2000 MHz) < 1.2 (50 – 1000 / 1600 – 2000 MHz) 50 Ω < 100 W < 50 W –30 … +60 °C N female Indoor By-pass (max. 2500mA) Short circuited Stop With 4 screws (max.4 mm diameter) 0.7 kg 220 x 40 x 140 mm 199.5 x 23 x 110.4 mm (incl. connectors) 200 400 600 800 1000 1200 1400 1600 1800 Frequency/MHz Diagram II Port 1 Port 3 Attenuation/dB Pass band Band 1 Band 2 Insertion loss Port 1 Port 3 Port 2 Port 3 Isolation Port 1 Port 2 10 40 Technical Data Type No. Port 2 Port 3 0 2000 Port 2 Port 3 0 0.1 0.2 1600 – 2000 50 – 1000 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0 200 400 600 800 1000 1200 1400 1600 1800 Frequency/MHz 2000 Dual-Band Combiner 50–- 2200 2200 MHz 50 MHz 2400 – 2500 MHz 80 160/ 400 / 400 / 900 / 1800 / UMTS 80 //160 / 900 / 1800 / UMTS 2100 WLAN • Designed for inhouse multiband distribution networks • Enables feeder sharing Port 3 • DC by-pass between ports 1 and 3 • Built-in DC stop between ports 2 and 3 Port 1 Port 2 Typical Attenuation Curves Attenuation/dB Diagram I Port 1 ↔ Port 3 Technical Data Port 2 ↔ Port 3 0 10 2400 – 2500 20 50 – 2200 30 40 50 936.2466/a 782 10264 Pass band Band 1 Band 2 Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 Isolation Port 1 ↔ Port 2 > 50 dB (50 – 2200 / 2400 – 2500 MHz) VSWR < 1.25 (50 – 2200 / 2400 – 2500 MHz) Impedance Input power Band 1 Band 2 Intermodulation products Temperature range Connectors Application Special features Mounting Weight Packing size Dimensions (w x h x d) 60 70 50 – 2200 MHz 2400 – 2500 MHz 80 90 < 0.1 dB (50 – 2200 MHz) < 0.2 dB (2400 – 2500 MHz) 100 0 50 < 200 W < 200 W < –150 dBc (3rd order; with 2 x 20 W) –20 ... +55 °C 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Diagram II Port 1 ↔ Port 3 Attenuation/dB Subject to alteration. Type No. Port 2 ↔ Port 3 0 0.1 2400 – 2500 0.2 50 – 2200 0.3 N female 0.4 Indoor 0.5 Built-in DC stop between ports 2 and 3 DC by-pass between ports 1 and 3 (max. 2500 mA) With 4 screws (max. 4 mm diameter) 0.6 0.47 kg 0.8 225 mm x 140 mm x 75 mm 86 mm x 30.4 mm x 181.4 mm (including connectors and mounting feet) 0.9 0.7 1.0 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz 782 10264 Page 1 of 1 Internet: http://www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone +49 8031 1 84-0 . Fax +49 8031 1 84-9 91 237 Dual-Band Combiner 50 - 470 MHz PMR / TETRA / TETRAPOL 790- -2500 2500MHz MHz 790 CDMA 800 // GSM GSM900 900/ /GSM GSM1800 1800/ UMTS / UMTS / WLAN CDMA 800 2100 / WLAN • Designed for co-siting purposes • Enables feeder sharing Port 3 • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications Port 1 • Wall or mast mounting • External DC stop available as an accessory Port 2 • Very low insertion loss • High input power 790 790 790 782 10458 782 10460 Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 � Port 3 Port 2 � Port 3 Isolation Port 1 � Port 2 VSWR 782 10457 87.5 - 470 MHz 790 - 2500 MHz 50 - 470 MHz 790 - 2500 MHz < 0.15 dB (87.5 - 470 MHz) < 0.15 dB (790 - 2500 MHz) < 0.15 dB (50 - 470 MHz) < 0.15 dB (790 - 2500 MHz) > 50 dB (250 - 470 / 790 - 2500 MHz) > 40 dB (87.5 - 250 MHz) > 50 dB (50 - 470 / 790 - 2500 MHz) < 1.25 (87.5 - 470 / 790 - 960 / 1710 - 2500 MHz) 936.2967c Subject to alteration. Impedance Input power Band 1 / Band 2 < 500 W / < 500 W Intermodulation products < -160 dBc (3rd order; with 2 x 20 W) Temperature range -55 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 � Port 3 Port 2 � Port 3 Mounting Weight Packing size Dimensions (w x h x d) www.kathrein.de < 1.25 (50 - 470 / 790 - 960 / 1710 - 2500 MHz) 50 � By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 4.0 kg 210 x 150 x 440 mm 122 x 64 x 364.3 mm (including mounting brackets) 78210457, 78210458 ... Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 238 Dual-Band Combiner 50 - 470 MHz PMR / TETRA / TETRAPOL 790 -- 2500 790 2500MHz MHz CDMA800 800/ GSM / GSM900 900 / GSM 1800 / UMTS / WLAN CDMA / GSM 1800 / UMTS 2100 / WLAN Typical Attenuation Curves 78210457 Diagram II Diagram I Port 1 � Port 3 Port 2 � Port 3 Attenuation/dB 10 20 790 – 2500 87.5 – 470 30 0.2 0.4 0.5 60 0.6 70 0.7 80 0.8 90 0.9 790 – 2500 87.5 – 470 0.3 50 1.0 0 250 500 750 0 1000 1250 1500 1750 2000 2250 2500 78210458 Port 1 � Port 3 750 Port 1 � Port 3 Attenuation/dB 10 20 30 500 790 – 2500 1000 1250 1500 1750 2000 2250 2500 Frequency/MHz Diagram II Port 2 � Port 3 0 87.5 – 470 250 Frequency/MHz Diagram I Port 2 � Port 3 0 0.1 0.2 40 0.4 50 0.5 60 0.6 70 0.7 80 0.8 90 0.9 790 – 2500 87.5 – 470 0.3 1.0 100 250 500 750 78210460 Port 1 � Port 3 500 750 0 20 790 – 2500 1000 1250 1500 1750 2000 2250 2500 Frequency/MHz Diagram II Port 2 � Port 3 10 50 – 470 250 Frequency/MHz Diagram I 30 0 1000 1250 1500 1750 2000 2250 2500 Port 1 � Port 3 Attenuation/dB 0 Subject to alteration. Attenuation/dB 0 0.1 40 100 Attenuation/dB Port 2 � Port 3 Port 2 � Port 3 0 0.1 0.2 50 – 470 0.3 40 0.4 50 0.5 60 0.6 70 0.7 80 0.8 90 0.9 790 – 2500 936.2967c Attenuation/dB Port 1 � Port 3 0 1.0 100 0 250 Page 2 of 2 500 750 1000 1250 1500 1750 2000 2250 2500 Frequency/MHz 78210457, 78210458 ... 0 250 500 750 1000 1250 1500 1750 2000 2250 2500 Frequency/MHz www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 239 Dual-Band Combiner 790 - 862 MHz LTE 800 880 - 960 MHz GSM 900 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC stop available as an accessory Port 3 Port 1 Port 2 78210970, 78210972, 78210974 Single Unit 78210971, 78210973, 78210975 Double Unit Technical Data Type No. 78210970 78210972 78210974 78210971 78210973 78210975 Single Unit Single Unit Double Unit Single Unit Double Unit Pass band Band 1 Band 2 Double Unit 790 - 862 MHz 880 - 960 MHz Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 < 0.4 dB, typically 0.2 dB (790 - 862 MHz) < 0.4 dB, typically 0.2 dB (880 - 960 MHz) Isolation Port 1 ↔ Port 2 > 50 dB (790 - 862 MHz / 880 - 960 MHz) VSWR < 1.25 (790 – 862 / 880 – 960 MHz) Impedance 50 Ω Input power Band 1 / Band 2 < 200 W / < 200 W Intermodulation products < -160 dBc (3rd order; with 2 x 20 W) Temperature range -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 240 By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 2.9 kg / Double Unit: 5.8 kg Single Unit: 392 x 272 x 139 mm / Double Unit: 392 x 272 x 189 mm Single Unit: 177.4 x 52.4 x 209.4 mm / Double Unit: 177.4 x 108.4 x 209.4 mm (without connectors, without mounting brackets) Dual-Band Combiner 790 - 862 MHz LTE 800 880 - 960 MHz GSM 900 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. 78210850V01 78410367 Clamp Set Clamp set suitable for mast diameter of DC stop 50-Ohm load Typical Attenuation Curves Diagram I Port 1 ↔ Port 3 Port 2 ↔ Port 3 DC stop 50-Ohm load Side view Single Unit Diagram II Port 1 ↔ Port 3 Port 2 ↔ Port 3 Side view Double Unit Top view Single Unit, Double Unit Bottom view Single Unit, Double Unit 241 Dual-Band Combiner 790 - 862 MHz LTE 800 880 - 960 MHz GSM 900 Designed to support separate DC/AISG supply for a low-band and high-band DTMA via 2 feeder cables (see application) Enables feeder sharing Can be used as a combiner near the BTS or in a reciprocal function near the antenna Suitable for indoor or outdoor applications Wall or mast mounting Double unit for XXPol antennas Built-in lightning protection External DC stop available as an accessory Unit 2 Port 3 Port 1 Port 2 Unit 1 Technical Data 78210979 Type No. Double Unit Pass band Band 1 Band 2 790 - 862 MHz 880 - 960 MHz Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 < 0.4 dB, typically 0.2 dB (790 - 862 MHz) < 0.4 dB, typically 0.2 dB (880 - 960 MHz) Isolation Port 1 ↔ Port 2 > 50 dB (790 - 862 MHz / 880 - 960 MHz) VSWR < 1.25 (790 - 862 / 880 - 960 MHz) 50 Ω Impedance Input power Band 1 / Band 2 Intermodulation products < 200 W / < 200 W < -160 dBc (3rd order; with 2 x 20 W) Temperature range -40 ... +60 °C Connectors 7-16 female (long neck) Application DC/AISG transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 242 Indoor or outdoor (IP 66) Unit 1 By-pass (max. 2500 mA) Stop Unit 2 Stop By-pass (max. 2500 mA) 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 5.8 kg 384 x 267 x 184 mm 177.4 x 209.4 x 108.4 mm (without connectors, without mounting brackets) Dual-Band Combiner 790 - 862 MHz 880 - 960 MHz LTE 800 GSM 900 Accessories (order separately) Clamp Set Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. Description 78210850V01 Diagram II Port 1 ↔ Port 3 Port 2 ↔ Port 3 50-Ohm load 50-Ohm load Application Example Smart Bias Tee Port 2 ↔ Port 3 DC stop DC stop 78410367 Typical Attenuation Curves Diagram I Port 1 ↔ Port 3 Smart Bias Tee 243 Dual-Band Combiner 470 – 960 MHz 1710 – 2700 MHz LTE 800 / CDMA 850 / GSM 900 GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas Port 1 as a double unit • Built-in lightning protection • External DC stop available as an accessory • Extremely small dimensions and low weight • Very low insertion loss Port 3 Port 2 782 10660, 782 10662, 782 10664 Single Unit 782 10661, 782 10663, 782 10665 Double Unit • High input power 470 – 960 1710 – 2700 470 – 960 470 – 960 1710 – 2700 1710 – 2700 Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 Port 3 Port 2 Port 3 Isolation Port 1 Port 2 782 10660 782 10662 Single Unit Single Unit Single Unit 782 10661 782 10663 782 10665 Double Unit Double Unit Double Unit 470 – 960 MHz 1710 – 2700 MHz < 0.1 dB (470 – 960 MHz) < 0.1 dB (1710 – 2700 MHz) > 55 dB (470 – 960 MHz) / > 65 dB (1710 – 2700 MHz) 936.3891/a Subject to alteration. VSWR < 1.2 (470 – 960 / 1710 – 2700 MHz) Impedance Input power Band 1 / Band 2 Intermodulation products 50 Ohm < 650 W / < 350 W < –160 dBc (3 rd order with 2 x 20 W) Temperature range –55 ... +60 °C Connectors Application DC/AISG transparency Port 1 Port 3 Port 2 Port 3 Lightning protection Mounting Weight 782 10664 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop 3 kA, 10/350 s pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 1.2 kg / Double Unit: 2.4 kg Packing size Single Unit: 285 x 157 x 93 mm / Double Unit: 285 x 157 x 148 mm Dimensions (w x h x d) Single Unit: 126 x 145 x 38 mm / Double Unit: 126 x 145 x 93 mm (without connectors, without mounting brackets) www.kathrein.de 782 10660, 782 10661, 782 10662, 782 10663, 782 10664, 782 10665 Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 244 suitable for mast diameter of 734 360 Port 1 Port 3 Attenuation/dB Type No. 34 – 60 mm 734 361 60 –Combiner 80 mm Dual-Band 734 362 734 363470 80 – 100 mm – 960 100 – MHz 120 mm LTE 800 / CDMA 850 / GSM 900 734 364 120 – 140 mm DC stop 1710 – 2700 MHz 784 361 10367 734 load 6050-Ohm – 80 mm 734 362 80 – 100 mm -70 Port 1 Port 3 DC stop 0 -20 -40 734 365 45 – 125 mm -50 78410367 784 10367 -100 900 1200 1500 1710 – 2700 1800 2100 2400 2700 3000 Frequency/MHz Diagram II Port 1 Port 3 -60 50-Ohm load 470 – 960 300 600 0 Attenuation/dB 782 10850 -90 -30 120 – 140 mm Port 2 Port 3 -80 -10 734 364 Description Description Typical Attenuation Curves Diagram I 100 – 120 mm 78210850V01 1710 – 2700 470 – 960 -30 -60 Clamp 50-OhmSet load 734 363 Type No. Type No. -20 -50 Attenuation/dB 782 360 10850 734 Type Type No. No. -10 GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 -40 734 365 45 – 125 mm Accessories (order separately) Clamp set suitable for mast Description diameter of 34 –DC60stop mm Port 2 Port 3 0 Port 2 Port 3 0 -70 DC stop DC stop -80 50-Ohm load 50-Ohm load -90 -0.1 -0.2 1710 – 2700 470 – 960 -0.3 -100 0 -0.4 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz -0.5 Diagram II -0.6 Attenuation/dB Port 1 Port 3 Side view Single Unit 0 Port 2 Port 3 -0.7 -0.1 -0.8 -0.2 -0.9 1710 – 2700 470 – 960 -0.3 -1.0 0 300 600 900 1200 1500 1800 -0.4 2100 2400 2700 3000 Frequency/MHz -0.5 Side view Double Unit -0.6 -0.7 Please note: As-0.8 a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. These facts must be considered during theFrequency/MHz site planning process. Top view The Dual-band Combiners are designed to operate under the environmental Single Unit, conditions as described in ETS 300 019-1-4 class 4.1 E and have passed Side view environmental tests as recommended in ETS 300 019-2-4. Double Unit Double Unit Thenote: installation team must be properly qualified and also be familiar with Please the relevant national safety regulations. As a result of more stringent legal regulations and judgements regarding product liability,given we areinobliged to sheets point out certain that may arise when The details our data have to berisks followed carefully when productsthe arecombiner used under installing andextraordinary accessories.operating conditions. 936.3891/a Subject to alteration. Extraordinary conditions,torque such asofheavy icing or exceptional dynaThe limitsoperating for the coupling RF connectors, mic recommended stress (e.g. strainby caused by oscillating support structures), may result in the connector manufacturers must the breakage of a mast mounted device or even cause it to fall to the ground. be obeyed. These facts must be considered during the site planning process. Terminate unused inputs with a suitable 50-Ohm load, Top view 784 10367. The e.g. Dual-band Combiners are designed to operate under the environmental Single Unit, conditions as described in ETS 300 019-1-4 class 4.1 E and have passed Any previous issuesinhave become environmental tests datasheet as recommended ETS now 300 019-2-4. Double Unit invalid. The installation team must be properly qualified and also be familiar with the 782 relevant national safety regulations. Page 2 of 2 782 10660, 782 10661, 782 10662, 782 10663, 782 10664, 10665 www.kathrein.de The details given in our data sheets have to be followed carefully when . Germany KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004installing Rosenheim Phone +49 8031 184-0 . Fax +49 8031 184-494 the combiner and. accessories. The limits for the coupling torque of RF connectors, recommended by the connector manufacturers must be obeyed. Terminate unused inputs with a suitable 50-Ohm load, e.g. 784 10367. Any previous datasheet issues have now become invalid. Page 2 of 2 782 10660, 782 10661, 782 10662, 782 10663, 782 10664, 782 10665 www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 245 Subject to alteration. -0.9 Extraordinary operating conditions, such as heavy icing or exceptional dynamic-1.0 stress (e.g. strain caused by oscillating support structures), may result in the breakage mast900 mounted even2100 cause it to2700 fall to3000 the ground. 0 300 of a600 1200 device 1500 or 1800 2400 936.3891/a Side view Single Unit Dual-Band Combiner 470 – 960 MHz DVB-H / CDMA 850 / GSM 900 1710 – 2700 MHz GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 • Designed to support separate DC/AISG supply for Unit 2 a low-band and high-band DTMA via 2 feeder cables (see application) • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna Suitable for indoor or outdoor applications • • Wall or mast mounting • Double unit for XPol antennas • Built-in lightning protection • Extremely small dimensions and low weight • Very low insertion loss • High input power Port 3 Port 1 Port 2 Unit 1 Application Example Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 Port 3 Port 2 Port 3 Isolation Port 1 Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 Port 2 Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 248 246 78210669 Double Unit 470 – 960 MHz 1710 – 2700 MHz < 0.1 dB (470 – 960 MHz) < 0.1 dB (1710 – 2700 MHz) > 55 dB (470 – 960 MHz) / > 65 dB (1710 – 2700 MHz) < 1.2 (470 – 960 / 1710 – 2700 MHz) 50 Ohm < 650 W / < 350 W < –160 dBc (3 rd order with 2 x 20 W) –55 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) Unit 1 Unit 2 By-pass (max. 2500 mA) Stop Stop By-pass (max. 2500 mA) 3 kA, 10/350 s pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 2.4 kg 285 x 157 x 148 mm 126 x 145 x 93 mm (without connectors, without mounting brackets) Port 1 Port 3 Attenuation/dB suitable for mast diameter of 734360 34 – 60 mm Dual-Band Combiner DVB-H / CDMA 850 / GSM 900 734363 100 – 120 mm Accessories (order 734364 120separately) – 140 mm 734365 Type No. Clamp 45 –set 125 mm suitable for mast diameter of 734360 34 – 60 mm 734361 60 – 80 mm Type No. 734362 78210850 Description 80 – 100DC mmstop 734363 100 – 120 mm 734364 120 – 140 mm 734365 45 – 125 mm 78410367 Type No. No. Type 78210850V01 78210850 78410367 78410367 50-Ohm load Description Description DC stop DC stop 50-Ohm load 50-Ohm load 1710 – 2700 MHz DC stop GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 -10 -20 1710 – 2700 470 – 960 -30 -40 Typical Attenuation Curves Clamp Set -50 Diagram I Port 1 Port 3 50-Ohm load DC stop Port 2 Port 3 -60 0 -70 -10 -80 -20 1710 – 2700 470 – 960 -30 -90 -40 -100 -50 0 300 600 900 1200 1500 -60 50-Ohm load 1800 Diagram II Port 1 Port 3 -90 -100 0 300 600 Diagram II -0.1 1200 1500 -0.2 1800 2100 2400 2700 3000 Frequency/MHz 1710 – 2700 470 – 960 Port 1 Port 3 -0.3 0 Port 2 Po 0 900 Port 2 Port 3 -0.4 -0.1 -0.5 -0.2 1710 – 2700 470 – 960 -0.6 -0.3 -0.4 -0.7 -0.5 -0.8 -0.6 -0.9 -0.7 -1.0 -0.8 0 300 600 900 1200 1500 -0.9 -1.0 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Side view Side view Top view 2 Frequency -70 -80 2100 Multiband Combiners 470 – 960 80 MHz 734362 – 100 mm Attenuation/dB 60 – 80 mm Attenuation/dB 734361 Port 2 Po 0 Attenuation/dB Type No. Top view 247 249 1800 2100 2 Frequency Dual-Band Combiner 380 - 960 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 1710 - 2700 MHz GSM1800 / UMTS 2100 / WiMAX / LTE 2600 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC stop available as an accessory • Extremely low insertion loss • High input power Port 1 Port 3 Port 2 78210680, 78210682 Single Unit 78210681, 78210683 Double Unit Technical Data 380 – 960 Type No. 78210680 78210682 78210681 78210683 1710 – 2700 380 – 960 Single Unit 1710 – 2700 Single Unit Double Unit Double Unit Pass band Band 1 Band 2 380 - 960 MHz 1710 - 2700 MHz Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 < 0.1 dB (380 – 960 MHz) < 0.1 dB (1710 – 2700 MHz) Isolation Port 1 ↔ Port 2 > 55 dB (380 – 550 MHz) / > 65 dB (550 – 960 MHz) / > 65 dB (1710 – 2700 MHz) VSWR < 1.2 (380 – 960 / 1710 – 2700 MHz) Impedance 50 Ω Input power Band 1 / Band 2 Intermodulation products < 700 W / < 700 W < -160 dBc (3rd order; with 2 x 20 W) Temperature range -55 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 248 By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Single Unit: 2 kg / Double Unit: 3.9 kg Single Unit: 365 x 207 x 150 mm / Double Unit: 365 x 207 x 214 mm Single Unit: 117 x 203.46 x 48.8 mm / Double Unit: 117 x 203.46 x 99.3 mm (without connectors, without mounting brackets) Dual-Band Combiner 380 - 960 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 1710 - 2700 MHz GSM 1800 / UMTS 2100 / WiMAX / LTE 2600 Accessories (order separately) Clamp Set Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. Type No. 78210850V01 78210850 78410367 78410367 Description Description DC stop DC stop 50-Ohm load 50-Ohm load 50-Ohm load Dimensions Typical Attenuation Curves Diagram I Port 1 ↔ Port 3 DC stop Port 2 ↔ Port 3 Side view Single unit Side view Double unit Top view Single unit Double unit Diagram II Port 1 ↔ Port 3 Port 2 ↔ Port 3 Bottom view Single unit Double unit 249 Dual-Band Combiner 790 – 1880 MHz 1920–- 2170 1920 2170MHz MHz UMTS UMTS 2100 LTE 800 / CDMA 850 / GSM 900 / GSM 1800 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or Port 3 Port 1 in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas Port 2 782 10278, 782 10305 Single Unit as a double unit • Built-in lightning protection • External DC Stop available as an accessory 782 10279, 782 10306 Double Unit Technical Data Type No. 782 10278 782 10305 782 10279 782 10306 Single Unit Single Unit Double Unit 936.2756/f Subject to alteration. Pass band Band 1 Band 2 Insertion loss Port 1 Port 3 Port 2 Port 3 Isolation Port 1 Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Double Unit 790 – 1880 MHz 1920 – 2170 MHz < 0.1 dB, typically 0.05 dB (790 – 960 MHz) / < 0.4 dB, typically 0.2 dB (1710 – 1880 MHz) < 0.4 dB, typically 0.2 dB (1920 – 2170 MHz) > 55 dB (790 – 960 MHz) > 50 dB (1710 – 1880 MHz, 1920 – 1980 MHz, 2110 – 2170 MHz) < 1.2 (790 – 960 MHz) / < 1.25 (1710 – 1880 MHz) / < 1.2 (1920 – 2170 MHz) 50 Ω < 500 W / < 500 W < –160 dBc (2nd/3rd order; with 2 x 20 W) –55 ... +60 °C Connectors 7-16 female (long neck) Application DC/AISG transparency Port 1 Port 3 Port 2 Port 3 Indoor or outdoor (IP 66) Lightning protection Mounting Weight Packing size Dimensions (w x h x d) www.kathrein.de By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) 3 kA, 10/350 s pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 3.4 kg / Double Unit: 6.6 kg Single Unit: 207 x 437 x 154 mm / Double Unit: 207 x 437 x 214 mm Single Unit: 130 x 269.9 x 43 mm / Double Unit:130 x 269.9 x 98.5 mm (without connectors, without mounting brackets) 782 10278, 782 10279, 782 10305, 782 10306 Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 250 Combiner Dual-Band Combiner 1880 MHz 1920 – 2170 MHz 0 / GSM 900 / GSM 1800 790 – 1880 MHz UMTS 1920 -–2170 1920 2170MHz MHz UMTS UMTS 2100 LTE 800 / CDMA 850 / GSM 900 / GSM 1800 r separately) Accessories (order separately) – 100 mm – 120 mm – 140 mm – 125 mm Diagram I suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 0 10 20 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 DC120stop – 140 mm 40 734 365 45 – 125 mm 50 Type No. No. Type Description Description 78210850V01 DC stop DC stop 784 10367 50-Ohm load Port 3 Port Port 2 2 Port 3 0 10 20 1920 02170 790 01880 30 1920 02170 790 01880 40 30 50 60 70 80 50-Ohm load 60 90 70 DC stop 782 10850 Diagram I Port 1 PortPort 3 1 Port 3 Attenuation/dB – 80 mm Type No. Typical Attenuation Curves Typical Attenuation Curves Clamp Set 7841036750-Ohm 50-Ohm loadload 100 500 700 900 1100 1300 1500 90 scription 1900 2100 2300 2500 Diagram II Port 1 Port 3 100 500 C stop 1700 Frequency/MHz 80 700 Ohm load Attenuation/dB – 60 mm Clamp Set Clamp set Attenuation/dB amp set le for mast meter of Port 2 Port 3 0 900 1100 0.1 1300 1500 1700 1900 2100 2300 2500 Frequency/MHz 0.2 790 01880 1920 02170 0.3 Diagram II 0.4 Side view, Single Unit Attenuation/dB Port 1 Port 3 0.6 0.1 0.7 0.2 0.8 790 01880 0.9 0.3 1.0 500 0.4 Unit Port 2 Port 3 0.5 0 700 900 1100 1920 02170 1300 1500 1700 1900 2100 2300 2500 Frequency/MHz 0.5 Side view, Double Unit 0.6 Single Earthing Instruction Unit Double Unit 0.7 0.8 0.9 1.0 500 700 900 Toothed washer Earthing cable (not included in the scope of delivery) Internal earthing1500 cable 1700 1900 2100 2300 2500 1100 1300 Washer Frequency/MHz Earthing screw Torque 6-7 Nm Unit Please note: Earthing Instruction The mounting plates can be removed by loosening the screws to always provided Single Unit(M5 x 10) and replaced with other means of mounting, Double Unit that the Top view, Single Unit, Double Unit (not included in the scope of delivery) These facts must be considered during the site planning process. The Dual-band Combiners are designed to operate under the environmental earthing cable conditions asInternal described in ETS 300 019-1-4 class 4.1 E and have passed environmental tests as recommended in ETS 300 019-2-4. Washer The installation Earthing team mustscrew be properly qualified and also be familiar with the relevant national safety regulations. Torque 6-7 Nm Bottom view, Single Unit, Double Unit Please note: The details given in our data sheets have to be followed carefully when installing the antennas, filters, combiners, amplifiers and accessories. The limits for the coupling torque of RF connectors, recommended by the be obeyed. The mounting platesconnector can be manufacturers removed bymust loosening the screws to (M5 x 10) and replaced withunused other inputs means ofamounting, always that the load,provided e.g. 784 10367. Terminate with suitable 50-Ohm max. drilled depth of 8.5 mm is respected with the choice of replacement Any previous datasheet issues have now become invalid. screws. 782 10278, 782 10279, 782 10305, 782 10306 www.kathrein.de As a result of more stringent legal regulations and judgements regarding . 83004 we . Germany . Phoneout . Fax product liability, are obliged to point risks that KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 Rosenheim +49certain 8031 184-0 +49may 8031 arise 184-494 when products are used under extraordinary operating conditions. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of a mast mounted device or even cause it to fall to the ground. These facts must be considered during the site planning process. 251 The Dual-band Combiners are designed to operate under the environmental Subject to alteration. Page 2 of 2 Extraordinary operating conditions, Toothed washersuch as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the Earthing breakage of a mast mountedcable device or even cause it to fall to the ground. Subject to alteration. As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. 936.2756/f 4 screws M5 x 10 4 spring washers 5.5 DIN 6095 nit, Unit max. drilled depth of 8.5 mm is respected with the choice of replacement screws. Dual-Band Combiner 1710 - 1880 MHz GSM 1800 1920 - 2200 MHz UMTS 2100 Designed for co-siting purposes Port 3 Port 1 Enables feeder sharing Can be used as a combiner near the BTS or in a reciprocal function near the antenna Suitable for indoor or outdoor applications Port 2 Wall or mast mounting Available as a single unit, or for XPol antennas as a double unit Built-in lightning protection External DC stop available as an accessory 78210620, 78210622, 78210624 Single Unit 78210621, 78210623, 78210625 Double Unit Technical Data Type No. 78210620 78210622 78210624 78210621 78210623 78210625 Single Unit Single Unit Double Unit Single Unit Double Unit Pass band Band 1 (GSM 1800) Band 2 (UMTS) Double Unit 1710 - 1880 MHz 1920 - 2200 MHz Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 < 0.3 dB (1710 – 1880 MHz) < 0.3 dB (1920 – 2200 MHz) Isolation Port 1 ↔ Port 2 > 55 dB (1710 – 1880) / > 50 dB (1920 – 2200 MHz) VSWR < 1.2 (1710 – 1880) / (1920 – 2200 MHz) 50 Ω Impedance Input power Band 1 / Band 2 < 300 W / < 300 W < –160 dBc (3rd order; with 2 x 20 W) Intermodulation products Temperature range -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 252 By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 2.2 kg / Double Unit: 4.3 kg Single Unit: 392 x 272 x 139 mm / Double Unit: 392 x 272 x 189 mm Single Unit: 163.5 x 195.3 x 46 mm / Double Unit: 163.5 x 195.3 x 102 mm (without connectors, without mounting brackets) Dual-Band Combiner 1710 - 1880 MHz GSM 1800 1920 - 2200 MHz UMTS 2100 Accessories (order separately) Type No. 734360 Clamp set suitable for mast diameter of 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm 793301 78410367 Typical Attenuation Curves Diagram I Port 1 ↔ Port 3 Port 2 ↔ Port 3 Diagram II Port 1 ↔ Port 3 Port 2 ↔ Port 3 34 - 60 mm 734361 Type No. Clamp Set Clamp set suitable for mast diameter of DC stop 50-Ohm load DC stop 50-Ohm load Side view Single Unit Side view Double Unit Top view Single Unit, Double Unit Bottom view Single Unit, Double Unit 253 Dual-Band Combiner 1710 - 1880 MHz GSM 1800 1920 - 2200 MHz UMTS 2100 Unit 2 • Designed to support separate DC/AISG supply for a low-band and high-band DTMA via 2 feeder cables (see application) • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Double unit for XPol antennas • Built-in lightning protection Port 3 Port 1 Unit 1 Port 2 Application Example Technical Data Type No. 1710 - 1880 1920 - 2200 1710 - 1880 Unit 1 1920 - 2200 Unit 2 78210626 Double Unit Pass band Band 1 (GSM 1800) Band 2 (UMTS) Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 Isolation Port 1 ↔ Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range 1710 - 1880 MHz 1920 - 2200 MHz < 0.3 dB (1710 – 1880 MHz) < 0.3 dB (1920 – 2200 MHz) > 55 dB (1710 – 1880 MHz) / > 50 dB (1920 – 2200 MHz) < 1.2 (1710 – 1880) / (1920 – 2200 MHz) 50 Ω < 300 W / < 300 W < –160 dBc (3rd order; with 2 x 20 W) -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 254 Unit 1 By-pass (max. 2500 mA) Stop Unit 2 Stop By-pass (max. 2500 mA) 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 4.3 kg 392 x 272 x 189 mm 163,5 x 195,3 x 102 mm (without connectors, without mounting brackets) Dual-Band Combiner 1710 - 1880 MHz GSM 1800 1920 - 2200 MHz UMTS 2100 Accessories (order separately) Type No. Clamp Set DC stop 50-Ohm load Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Dimensions Type No. Clamp set suitable for mast diameter of 793301 DC stop 78410367 50-Ohm load Front view Typical Attenuation Curves Diagram I Port 1 ↔ Port 3 Port 2 ↔ Port 3 Side view Top view Diagram II Port 1 ↔ Port 3 Port 2 ↔ Port 3 Bottom view 255 Dual-Band Combiner 1850 – 1910 / 1930 – 1990 MHz 1710 – 1755 / 2110 – 2155 MHz PCS AWS • Designed for co-siting purposes • Enables feeder sharing • Suitable for indoor or outdoor applications COM ANT • With fault detection and integrated switch for multiple DC power supply AWS PCS 782 10469 Typical Attenuation Curves Diagram I Port AWS ↔ Port ANT Pass band PCS AWS Insertion loss Port PCS ↔ Port ANT Port AWS ↔ Port ANT Isolation Port PCS ↔ Port AWS VSWR Double unit 1850 – 1910 (Rx) / 1930 – 1990 (Tx) MHz 1710 – 1755 (Rx) / 2110 – 2155 (Tx) MHz < 250 W (1850 – 1910 / 1930 – 1990 MHz) < 250 W (1710 – 1755 / 2110 – 2155 MHz) survival Polarity protection Max. Current Power supply current at PCS port operating with dummy load Lightning protection Temperature range -10 1850 – 1910 -20 –48 V DC (Port PCS, Port AWS) 1.5 A (Port ANT) -60 -70 -80 -90 -100 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 Frequency/MHz Diagram II Port Port AWS ↔ ANT Port Port PCS ↔ ANT Port Port AWS ↔ ANT 0 -0.1 -0.2 2110 – 2155 1710 – 1755 -0.3 1850 – 1910 100 mA ±20mA (+10 ... +15 V DC) 8/20 +s, 20 kA; 10/350 +s, 3 kA (Port ANT) -0.4 1930 – 1990 -0.5 –40 ... +65 °C -0.6 Connectors 7-16 female (long neck) -0.7 Application Indoor or outdoor (IP 66) Weight Dimensions (w x h x d) 2110 – 2155 -30 < –160 dBc (3 rd order; with 2 x 20 W) +10 … +15 V DC (Port PCS) +10 … +30 V DC (Port AWS) +10 … +35 V DC 1930 – 1990 1710 – 1755 -50 > 50 dB (1850 – 1910 / 1930 – 1990 MHz) > 50 dB (1710 – 1755 / 2110 – 2155 MHz) < 1.25 (1850 – 1910 / 1930 – 1990 MHz) < 1.25 (1710 – 1755 / 2110 – 2155 MHz) 50 Port PCS ↔ Port ANT 0 -40 < 0.3 dB (1850 – 1910 / 1930 – 1990 MHz) < 0.2 dB (1710 – 1755 / 2110 – 2155 MHz) Impedance Power supply voltage operational Subject to alteration. 782 10808 Single unit Input power Port PCS Port AWS Intermodulation products 936.3232 782 10469 Attenuation/dB Type No. Attenuation/dB Technical Data 2.5 kg 5 kg 122 x 296 x 64 mm 122 x 296 x 120 mm (including mounting brackets) -0.8 -0.9 -1.0 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 Frequency/MHz Internet: http://www.kathrein.de 782 10469, 782 10808 Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 256 Dual-Band Combiner 1850 – 1910 / 1930 – 1990 MHz 1710 – 1755 / 2110 – 2155 MHz PCS AWS • Designed for co-siting purposes • Enables feeder sharing • Suitable for indoor or outdoor applications COM ANT • DC by-pass between all ports • External DC stop available as an accessory AWS PCS 782 10809 Typical Attenuation Curves Attenuation/dB Diagram I Port AWS ↔ Port ANT Technical Data Pass band PCS AWS Insertion loss Port PCS ↔ Port ANT Port AWS ↔ Port ANT Isolation Port PCS ↔ Port AWS 936.3344 Subject to alteration. VSWR Impedance Input power Port PCS Port AWS Intermodulation products Lightning protection Temperature range -10 1850 – 1910 -20 1930 – 1990 1710 – 1755 2110 – 2155 -30 -40 782 10809 782 10810 -50 Single unit Double unit -60 -70 1850 – 1910 (Rx) / 1930 – 1990 (Tx) MHz 1710 – 1755 (Rx) / 2110 – 2155 (Tx) MHz -80 -90 < 0.3 dB (1850 – 1910 / 1930 – 1990 MHz) < 0.2 dB (1710 – 1755 / 2110 – 2155 MHz) -100 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 Frequency/MHz > 50 dB (1850 – 1910 / 1930 – 1990 MHz) > 50 dB (1710 – 1755 / 2110 – 2155 MHz) < 1.25 (1850 – 1910 / 1930 – 1990 MHz) < 1.25 (1710 – 1755 / 2110 – 2155 MHz) 50 < 250 W (1850 – 1910 / 1930 – 1990 MHz) < 250 W (1710 – 1755 / 2110 – 2155 MHz) < –160 dBc (3 rd order; with 2 x 20 W) 3 kA, 10/350 +s pulse –40 ... +65 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) Diagram II Port Port AWS ↔ ANT Attenuation/dB Type No. Port PCS ↔ Port ANT 0 Port Port PCS ↔ ANT Port Port AWS ↔ ANT 0 -0.1 -0.2 2110 – 2155 1710 – 1755 -0.3 1850 – 1910 -0.4 1930 – 1990 -0.5 -0.6 DC/AISG transparency By-pass between all ports (max. 2500 mA) -0.7 Weight Dimensions (w x h x d) 2.5 kg 5 kg 122 x 296 x 64 mm 122 x 296 x 120 mm (including mounting brackets) -0.8 -0.9 -1.0 1700 1750 1800 1850 1900 1950 2000 2050 2100 2150 2200 Frequency/MHz Internet: http://www.kathrein.de 782 10809, 782 10810 Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 257 Dual-Band Combiner 1710 – 2180 MHz GSM1800 / PCS1900 / AWS / UMTS2100 2400 – 2700 MHz WLAN / WiMAX / BRS/ LTE2600 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or Port 3 Port 1 in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC stop available as an accessory • Very low insertion loss Technical Data Type No. Pass band Band 1 Band 2 Insertion loss Port 1 � Port 3 Port 2 � Port 3 Isolation Port 1 � Port 2 VSWR 1710 – 2180 2400 – 2700 Packing size 258 260 2400 – 2700 1710 – 2180 2400 – 2700 78211092 78211094 78211091 78211093 78211095 Single Unit Double Unit Single Unit Double Unit Single Unit Double Unit 1710 – 2180 MHz 2400 – 2700 MHz < 0.15 dB < 0.15 dB > 60 dB < 1.25 (1710 – 2180 / 2400 – 2700 MHz) 50 Ω < 300 W / < 300 W < –160 dBc (3 rd order with 2 x 20 W) Temperature range Connectors Application Dimensions (w x h x d) 1710 – 2180 78211091, 78211093, 78211095 Double Unit 78210800 Impedance Input power Band 1 / Band 2 Intermodulation products DC/AISG transparency Port 1 � Port 3 Port 2 � Port 3 Lightning protection Mounting Weight Port 2 78210800, 78211092, 78211094 Single Unit –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop 3 kA, 10/350 s pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 2.9 kg / Double Unit: 5.7 kg Single Unit: 392 x 272 x 139 mm / Double Unit: 392 x 272 x 189 mm Single Unit: 199 x 199 x 44 mm / Double Unit: 199 x 199 x 95 mm (without connectors, without mounting brackets) Dual-Band Combiner 1710 – 2180 MHz GSM1800 / PCS1900 / AWS / UMTS2100 Accessories (order separately) Clamp set suitable for mast diameter of 734361 60 – 80 mm 734362 80 – 100 mm 734363 100 – 120 mm 734364 120 – 140 mm 734365 45 – 125 mm Type No. No. Type 78210850V01 78210850 78410367 78410367 Diagram I Port 1 � Port 3 DC stop Port 2 � Port 3 0 10 20 30 1710 2180 2400 2700 40 Multiband Combiners 34 – 60 mm Typical Attenuation Curves Attenuation/dB 734360 Clamp Set 50 50-Ohm load Description Description 60 70 DC stop DC stop 50-Ohm load 50-Ohm load 80 90 100 1500 1650 1800 1950 2100 Diagram II Port 1 � Port 3 Single Unit Side view Attenuation/dB Type No. 2400 – 2700 MHz WLAN / WiMAX / BRS/ LTE2600 2250 2400 2550 2700 2850 3000 Frequency/MHz Port 2 � Port 3 0 0.1 0.2 0.3 1710 2180 2400 2700 0.4 0.5 Double Unit Side view 0.6 0.7 0.8 0.9 1.0 1500 1650 1800 1950 2100 2250 2400 2550 2700 2850 3000 Frequency/MHz Top view Single Unit Double Unit � � � � Please note: The mounting plates can be removed by loosening the screws � to � (M5 x 12) and replaced with other means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. Bottom view Single Unit Double Unit 261 259 Dual-Band Combiner 1710 - 2180 MHz 2400 - 2700 MHz GSM 1800 / PCS 1900 / AWS / UMTS 2100 WLAN / WiMAX / BRS / LTE 2600 • Designed to support separate DC/AISG supply for a low-band and high-band DTMA via 2 feeder cables (see application) • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Double unit for XPol antennas • Built-in lightning protection • Very low insertion loss Unit 2 Port 3 Port 1 Port 2 Unit 1 Application Example Technical Data Type No. 78211099 Double Unit Pass band Band 1 (GSM 1800) Band 2 (UMTS) Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 Isolation Port 1 ↔ Port 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range 1710 - 2180 MHz 2400 - 2700 MHz < 0.15 dB < 0.15 dB > 60 dB < 1.2 (1710 – 2180) / (2400 – 2700 MHz) 50 Ω < 300 W / < 300 W < –160 dBc (3rd order; with 2 x 20 W) -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 260 Unit 1 By-pass (max. 2500 mA) Stop Unit 2 Stop By-pass (max. 2500 mA) 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 5.7 kg 392 x 272 x 189 mm 199 x 199 x 95 mm (without connectors, without mounting brackets) Dual-Band Combiner 1710 - 2180 MHz GSM 1800 / PCS 1900 / AWS / UMTS 2100 Accessories (order separately) Type No. 734360 Typical Attenuation Curves Diagram I Port 1 ↔ Port 3 Port 2 ↔ Port 3 Diagram II Port 1 ↔ Port 3 Port 2 ↔ Port 3 34 - 60 mm 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. Description 78410367 Clamp Set Clamp set suitable for mast diameter of 734361 78210850V01 2400 - 2700 MHz WLAN / WiMAX / BRS / LTE 2600 DC stop 50-Ohm load DC stop 50-Ohm load Dimensions Side view Top view Bottom view 261 Dual-Band Combiner 380 (690) - 2180 MHz 2400 - 2700 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 / GSM 1800 / UMTS 2100 WiMAX / LTE 2600 • Designed for co-siting purposes Port 3 • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications Port 1 Port 2 • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit 78211180, 78211182, 78211184 Single Unit • Built-in lightning protection 78211181, 78211183, 78211185 Double Unit • External DC stop available as an accessory • Extremely small dimensions and low weight • Very low insertion loss • High input power Technical Data Type No. Pass band Band 1 Band 2 78211180 Single Unit 78211182 Single Unit 78211184 Single Unit 78211181 Double Unit 78211183 Double Unit 78211185 Double Unit 690 - 2180 MHz 2400 - 2700 MHz 380 - 2180 MHz 2400 - 2700 MHz Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 < 0.2 dB (690 - 2180 MHz) typ. 0.1 dB < 0.15 dB (2400 - 2700 MHz) typ. 0.1 dB < 0.2 dB (380 - 2180 MHz) typ. 0.1 dB < 0.15 dB (2400 - 2700 MHz) typ. 0.1 dB Isolation Port 1 ↔ Port 2 > 50 dB (690 - 2180 MHz / 2400 - 2700 MHz) > 50 dB (380 - 2180 MHz / 2400 - 2700 MHz) < 1.22 (690 - 2180 MHz) < 1.22 (1500 - 2180 MHz) / < 1.27 (380 - 1500 MHz) < 1.2 (2400 - 2700 MHz) VSWR < 1.2 (2400 - 2700 MHz) Impedance 50 Ω Input power Band 1 / Band 2 < 500 W / < 500 W Intermodulation products < -160 dBc (3rd order; with 2 x 20 W) Temperature range -55 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3 Lightning protection Mounting Weight By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) 3 kA, 10/350 µs pulse By-pass (max. 2500 mA) Stop Without lightning protection Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 1.5 kg / Double Unit: 2.8 kg Packing size Single Unit: 266 x 196 x 130 mm / Double Unit: 266 x 196 x 180 mm Dimensions (w x h x d) Single Unit: 141 x 119 x 48 mm / Double Unit: 141 x 119 x 98.5 mm (without connectors, without mounting brackets) 262 Dual-Band Combiner 380 (690) - 2180 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 / GSM 1800 / UMTS 2100 2400 - 2700 MHz WiMAX / LTE 2600 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. Clamp set suitable for mast diameter of 78210850V01 78410367 DC stop Clamp Set DC stop 50-Ohm load 50-Ohm load Typical Attenuation Curves 263 Triple-Band Combiner 380 – 960 MHz TETRA, LTE 800, CDMA 850, GSM 900 1710 – 1880 MHz 1920 – 2170 MHz GSM 1800 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC Stop available as an accessory UMTS 2100 Port 4 Port 1 Port 2 Port 3 78210630, 78210632, 78210634 Single Unit 78210631, 78210633, 78210635 Double Unit Technical Data Type No. 78210630 78210632 78210634 78210631 78210633 78210635 Single Unit Double Unit Pass band Band 1 (TETRA ... GSM 900) Band 2 (GSM 1800) Band 3 (UMTS) Insertion loss Port 1 � Port 4 Port 2 � Port 4 Port 3 � Port 4 Isolation Port 1 � Port 2 Port 1 � Port 3 Port 2 � Port 3 VSWR Impedance Input power Band 1 / Band 2 / Band 3 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 � Port 4 Port 2 � Port 4 Port 3 � Port 4 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 262 264 Single Unit Double Unit Single Unit Double Unit 380 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz < 0.2 dB ( 380 – 960 MHz) < 0.3 dB (1710 – 1880 MHz) < 0.3 dB (1920 – 2170 MHz) > 45 dB (380 – 600 MHz) / > 50 dB (600 – 960 / 1710 – 1880 MHz) > 45 dB (380 – 600 MHz) / > 50 dB (600 – 960 / 1920 – 2170 MHz) > 50 dB (1710 – 1880 / 1920 – 2170 MHz) < 1.25 (380 – 960 / 1710 – 1880 / 1920 – 2170 MHz) 50 Ω < 700 W / < 300 W / < 300 W < –160 dBc (3rd order; with 2 x 20 W) –40 ... +60 °C 7-16 female (long neck) Indoor or outdoor (IP 66) By-pass (max. 2500 mA) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) Stop Stop By-pass (max. 2500 mA) Stop 3 kA, 10/350 s pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 3.2 kg / Double Unit: 6.3 kg Single Unit: 392 x 292 x 139 mm / Double Unit: 392 x 292 x 189 mm Single Unit: 219 x 199 x 48 mm / Double Unit: 219 x 199 x 104 mm (without connectors, without mounting brackets) Triple-Band Combiner Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 – 60 mm 734361 60 – 80 mm 734362 80 – 100 mm 734363 100 – 120 mm 734364 120 – 140 mm 734365 45 – 125 mm TypeNo. No. Type Description Description 78210850V01 78210850 78410367 78410367 1710 – 1880 MHz 1920 – 2170 MHz GSM 1800 UMTS 2100 Typical Attenuation Curves Clamp Set Diagram I Port 1 Port 4 DC stop Port 2 Port 4 Port 3 Port 4 380 960 1920 2170 1710 1880 Multiband Combiners 380 – 960 MHz TETRA, LTE 800, CDMA 850, GSM 900 50-Ohm load DC stop DC stop 50-Ohm load 50-Ohm load Side view Single Unit Diagram II Port 1 Port 4 Side view Double Unit Port 2 Port 4 Port 3 Port 4 1920 2170 380 960 1710 1880 Top view Single Unit, Double Unit Bottom view Single Unit, Double Unit Please note: The mounting plates can be removed by loosening the screws to (M5 x 12) and replaced with other means of mounting, always provided that the max. drilled depth of 7.5 mm is respected with the choice of replacement screws. 263 265 Triple-Band Combiner 790 - 960 MHz LTE 800/ CDMA 850 / GSM 900 1710 - 2180 MHz GSM 1800 / UMTS 2100 2490 - 2690 MHz LTE 2600 • Designed for co-sitting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection 78211130, 78211132, 78211134, Single Unit 78211131, 78211133, 78211135, Double Unit Technical Data Type No. 78211130 Single Unit 78211132 Single Unit 78211134 Single Unit 78211131 Double Unit 78211133 Double Unit 78211135 Double Unit Pass band Band 1 (LTE 800, GSM 900) Band 2 (GSM 1800, UMTS 2100) Band 3 (LTE 2600) 790 - 960 MHz 1710 - 2180 MHz 2490 - 2690 MHz Insertion loss Port 1 ↔ Port 4 Port 2 ↔ Port 4 Port 3 ↔ Port 4 Isolation < 0.2 dB (790 - 960 MHz) < 0.2 dB (1710 - 2180 MHz) < 0.2 dB (2490 - 2690 MHz) Port 1 ↔ Port 2 Port 1 ↔ Port 3 Port 2 ↔ Port 3 VSWR > 50 dB (790 - 960 MHz) > 50 dB (1710 - 2180 MHz) > 50 dB (2490 - 2690 MHz) < 1.25 (790 - 960 / 1710 - 2180 / 2490 - 2690 MHz) 50 Ω Impedance Input power Band 1 / Band 2 / Band 3 Intermodulation products < 300 W / < 300 W / < 300 W < -160 dBc (3rd order; with 2 x 20 W) Temperature range -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 4 Port 2 ↔ Port 4 Port 3 ↔ Port 4 Lightning protection Mounting Weight Dimensions (w x h x d) 266 By-pass (max. 2500 mA) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop Stop By-pass (max. 2500 mA) Stop By-pass (max. 2500 mA) Stop 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Single unit: 3 kg / Double unit: 5.4 kg Single Unit: 199 x 199 x 48 mm / Double Unit: 199 x 199 x 104 mm (without connectors, without mounting brackets) Triple-Band Combiner 790 - 960 MHz LTE 800/ CDMA 850 / GSM 900 Accessories (order separately) Type No. 734360 34 - 60 mm 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm 78210850V01 78410367 Clamp Set 2490 - 2690 MHz LTE 2600 Typical Attenuation Curves Diagramm I Clamp set suitable for mast diameter of 734361 Type No. 1710 - 2180 MHz GSM 1800 / UMTS 2100 Clamp set suitable for mast diameter of DC stop DC stop 50-Ohm load 50-Ohm load Diagramm II Single Unit 78211130 78211132 78211134 Double Unit 78211131 78211133 78211135 267 Triple-Band Combiner 791 - 862 MHz LTE 800 880 - 960 MHz GSM 900 1710 - 2690 MHz GSM 1800 / UMTS 2100 / LTE 2600 • Designed for co-sitting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC Stop available as an accessory Technical Data Type No. 78211190 78211192 78211191 78211193 Single Unit Single Unit Double Unit Double Unit Pass band Band 1 Band 2 Band 3 791 - 862 MHz 880 - 960 MHz 1710 - 2690 MHz Insertion loss Port 1 ↔ Port 4 Port 2 ↔ Port 4 Port 3 ↔ Port 4 < 0.40 dB typ. 0.3 dB < 0.45 dB typ. 0.3 dB < 0.15 dB typ. 0.1 dB Isolation Port 1 ↔ Port 2 Port 1 ↔ Port 3 Port 2 ↔ Port 3 > 50 dB (791 - 862 / 880 - 960 MHz) > 50 dB (791 - 862 / 1710 - 2690 MHz) > 50 dB (880 - 960 / 1710 - 2300 / 2500 - 2700 MHz) > 32 dB (2300 - 2500 MHz) VSWR < 1.2 Impedance 50 Ω Input power Band 1 / Band 2 / Band 3 Intermodulation products < 300 W / < 300 W / < 300 W < -160 dBc (3rd order; with 2 x 20 W) Temperature range -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 4 Port 2 ↔ Port 4 Port 3 ↔ Port 4 Lightning protection Mounting Weight Dimensions (w x h x d) 268 By-pass (max. 2500 mA) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop Stop By-pass (max. 2500 mA) 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Single unit: Approx. 3.2 kg / Double unit: Approx. 6.3 kg Single unit: 181.4 x 212 x 66.5 mm / Double unit: 181.4 x 212 x 137.5 mm (without connectors, without mounting brackets) Triple-Band Combiner 791 - 862 MHz LTE 800 880 - 960 MHz GSM 900 Type No. 1710 - 2690 MHz GSM 1800 / UMTS 2100 / LTE 2600 Clamp set suitable for mast diameter of 734360 Clamp Set 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. DC stop Clamp set suitable for mast diameter of 78210850V01 DC stop 78410367 50-Ohm load Dimensions 50-Ohm load Typical Attenuation Curves Double Unit Single Unit 269 Quad-Band Combiner 380 - 960 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 1710 - 1880 MHz GSM 1800 • Designed for co-siting purposes • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Available as a single unit, or for XPol antennas as a double unit • Built-in lightning protection • External DC Stop available as an accessory 1920 - 2200 MHz UMTS 2100 2500 - 2690 MHz LTE 2600 Port 5 Port 1 Port 2 Port 3 Port 4 78210640, 78210642, 78210644 Single Unit 78210641, 78210643, 78210645 Double Unit Technical Data Type No. 78210640 78210642 78210644 78210641 78210643 78210645 Single Unit Single Unit Double Unit Single Unit Double Unit Pass band Band 1 (TETRA ... GSM 900) Band 2 (GSM 1800) Band 3 (UMTS) Band 4 (LTE 2600) Double Unit 380 - 960 MHz 1710 - 1880 MHz 1920 - 2200 MHz 2500 - 2690 MHz Insertion loss Port 1 ↔ Port 5 Port 2 ↔ Port 5 Port 3 ↔ Port 5 Port 4 ↔ Port 5 < 0.2 dB (380 - 960 MHz) < 0.3 dB (1710 - 1880 MHz) < 0.3 dB (1920 - 2200 MHz) < 0.2 dB (2500 - 2690 MHz) Isolation Port 1 ↔ Port 2 Port 1 ↔ Port 3 Port 1 ↔ Port 4 Port 2 ↔ Port 3 Port 2 ↔ Port 4 Port 3 ↔ Port 4 > 45 dB (380 - 600 MHz) / > 50 dB (600 - 960 / 1710 - 1880 MHz) > 45 dB (380 - 600 MHz) / > 50 dB (600 - 960 / 1920 - 2200 MHz) > 45 dB (380 - 600 MHz) / > 50 dB (600 - 960 / 2500 - 2690 MHz) > 50 dB (1710 - 1880 / 1920 - 2200 MHz) > 50 dB (1710 - 1880 / 2500 - 2690 MHz) > 50 dB (1920 - 2200 / 2500 - 2690 MHz) VSWR < 1.25 (380 - 960 / 1710 - 1880 / 1920 - 2200 / 2500 - 2690 MHz) Impedance Input power Band 1 / Band 2 / Band 3 / Band 4 50 Ω < 700 W / < 300 W / < 300 W / < 200 W Intermodulation products < -160 dBc (3rd order; with 2 x 20 W) Temperature range -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 5 Port 2 ↔ Port 5 Port 3 ↔ Port 5 Port 4 ↔ Port 5 Lightning protection Mounting Weight By-pass (max. 2500 mA) By-pass (max. 2500 mA) By-pass (max. 2500 mA) By-pass (max. 2500 mA) Stop Stop Stop By-pass (max. 2500 mA) Stop Stop By-pass (max. 2500 mA) Stop 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Single Unit: 3.8 kg / Double Unit: 7.5 kg Packing size Single Unit: 392 x 292 x 139 mm / Double Unit: 392 x 292 x 189 mm Dimensions (w x h x d) Single Unit: 215 x 228 x 50 mm / Double Unit: 215 x 228 x 106 mm (without connectors, without mounting brackets) 270 Quad-Band Combiner 380 - 960 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 1710 - 1880 MHz GSM 1800 1920 - 2200 MHz UMTS 2100 Typical Attenuation Curves 2500 - 2690 MHz LTE 2600 Dimensions Diagram I Port 1 ↔ Port 5 Port 2 ↔ Port 5 Port 3 ↔ Port 5 Port 4 ↔ Port 5 Side view Single unit Side view Double unit Top view Single Unit Double Unit Diagram II Port 1 ↔ Port 5 Port 2 ↔ Port 5 Port 3 ↔ Port 5 Port 4 ↔ Port 5 Bottom view Single Unit Double Unit Accessories (order separately) Type No. 734360 Clamp set suitable for mast diameter of 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. Description 78210850V01 78410367 Clamp Set DC stop 50-Ohm load DC stop 50-Ohm load 1.5 W / indoor or outdoor 271 Quad-Band Combiner 380 - 960 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 1710 - 1880 MHz GSM 1800 1920 - 2200 MHz UMTS 2100 2500 - 2690 MHz LTE 2600 Unit 2 • Designed to support separate DC/AISG supply for 2100 MHz and 2600 MHz band DTMA via 2 feeder cables (see application example) • Enables feeder sharing • Can be used as a combiner near the BTS or in a reciprocal function near the antenna • Suitable for indoor or outdoor applications • Wall or mast mounting • Built-in lightning protection Unit 1 Technical Data 78210649 Type No. Double Unit Pass band Band 1 (TETRA ... GSM 900) Band 2 (GSM 1800) Band 3 (UMTS) Band 4 (LTE 2600) 380 - 960 MHz 1710 - 1880 MHz 1920 - 2200 MHz 2500 - 2690 MHz Insertion loss Port 1 ↔ Port 5 Port 2 ↔ Port 5 Port 3 ↔ Port 5 Port 4 ↔ Port 5 < 0.2 dB (380 - 960 MHz) < 0.3 dB (1710 - 1880 MHz) < 0.3 dB (1920 - 2200 MHz) < 0.2 dB (2500 - 2690 MHz) Isolation Port 1 ↔ Port 2 Port 1 ↔ Port 3 Port 1 ↔ Port 4 Port 2 ↔ Port 3 Port 2 ↔ Port 4 Port 3 ↔ Port 4 > 45 dB (380 - 600 MHz) / > 50 dB (600 - 960 / 1710 - 1880 MHz) > 45 dB (380 - 600 MHz) / > 50 dB (600 - 960 / 1920 - 2200 MHz) > 45 dB (380 - 600 MHz) / > 50 dB (600 - 960 / 2500 - 2690 MHz) > 50 dB (1710 - 1880 / 1920 - 2200 MHz) > 50 dB (1710 - 1880 / 2500 - 2690 MHz) > 50 dB (1920 - 2200 / 2500 - 2690 MHz) VSWR < 1.25 (380 - 960 / 1710 - 1880 / 1920 - 2200 / 2500 - 2690 MHz) Impedance Input power Band 1 / Band 2 / Band 3 / Band 4 Intermodulation products 50 Ω < 700 W / < 300 W / < 300 W / < 200 W < -160 dBc (3rd order; with 2 x 20 W) Temperature range -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 ↔ Port 5 Port 2 ↔ Port 5 Port 3 ↔ Port 5 Port 4 ↔ Port 5 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 272 Unit 1 Stop Stop By-pass (max. 2500 mA) Stop Unit 2 Stop Stop Stop By-pass (max. 2500 mA) 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 7.5 kg 392 x 292 x 189 mm 215 x 228 x 106 mm (without connectors, without mounting brackets) Quad-Band Combiner 1710 - 1880 MHz GSM 1800 380 - 960 MHz TETRA / LTE 800 / CDMA 850 / GSM 900 1920 - 2200 MHz UMTS 2100 2500 - 2690 MHz LTE 2600 Typical Attenuation Curves Diagram II Diagram I Port 1 ↔ Port 5 Port 2 ↔ Port 5 Port 3 ↔ Port 5 Accessories (order separately) Type No. 734360 Port 1 ↔ Port 5 Port 2 ↔ Port 5 Port 3 ↔ Port 5 Port 4 ↔ Port 5 Application Example Clamp set suitable for mast diameter of 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. Description 78410367 50-Ohm load 1.5 W / indoor or outdoor Clamp Set Port 4 ↔ Port 5 50-Ohm load 273 SmartPlex Dual-Band Combiner 380 – 960 MHz TETRA / LTE 800 / DD / CDMA / GSM 900 1710 2690 1710 – - 2690 MHzMHz GSM / /PCS / AWS / UMTS 2100 / LTE 2600 GSM PCS / AWS / UMTS 2100 / LTE • Universal multi-protocol dual-band combiner AISG 1.1 AISG 2.0 3GPP Current window alarming (CWA) Vendor specific protocols Main 2 Main 1 Div 1 Div 2 • Designed for co-siting purposes • Enables feeder sharing • 78210900: For use near the base station (BTS), thereby converting different base station DC voltages into one common feeder DC voltage (multi-BTS power supply handling) 78210901: For use near the antenna (ANT), thereby reproducing the base station DC voltages for the antenna line devices 78210901 Feeder Main AISG Feeder Div • Simultaneous support of antenna line devices (TMAs, RET units) Feeder Main • Dynamic DC/AISG by-pass: Automatic setting on Feeder Div each RF path according to the BTS and antenna line device requirements • DC power supply either from BTS via RF path, or from an external source via AISG port (782 10900) • Provides full Smart Bias Tee functionality • Suitable for indoor or outdoor applications • Wall or mast mounting • Double unit in one housing for XPol antennas • Built-in lightning protection • Very low insertion loss • High input power Technical Data Type No. Pass band Band 1 / Band 2 Insertion loss Isolation Main 1 � Main 2 / Div 1 � Div 2 VSWR Impedance Input power Band 1 / Band 2 Intermodulation products Temperature range Connectors RF AISG Power consumption DC supply Application DC/AISG transparency Lightning protection Mounting Weight Dimensions (w x h x d) 274 268 78210900 Main 2 Main 1 AISG Div 1 Div 2 78210901 (ANT) 78210900 (BTS) 380 – 960 / 1710 – 2690 MHz < 0.2 dB, typically 0.15 dB (380 – 960 / 1710 – 2690 MHz) > 60 dB (380 – 960 / 1710 – 2690 MHz) < 1.22 (380 – 960 / 1710 – 2690 MHz) 50 Ohm < 500 W / < 300 W < –160 dBc (3rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) 8-pin, IEC 60130-9 (782 10900/901: Male/female) Pin 2: -48V DC (782 10900 only), Pin 3: RS485B, Pin 5: RS485A, Pin 6: Nominal 24 V DC, Pin 7: DC return (78210900/901: Not grounded/grounded), Other pins: Not connected 2 W (idle mode) 782 10900: 7 – 30 V DC (via RF connectors) Indoor or outdoor (IP 67) For AISG 1.1, AISG 2.0, 3GPP, vendor specific protocols and for current window alarm (CWA) controlled TMAs 3 kA (10/350 s pulse), 10 kA (8/20 s pulse) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 782 10900: 6.5 kg, 782 10901: 4.9 kg 782 10900: 233 x 258 x 79 mm 782 10901: 233 x 223 x 62 mm (without connectors, without mounting brackets) Application Example SmartPlex Dual-Band Combiner 380 – 960 MHz TETRA / LTE 800 / DD / CDMA / GSM 900 1710 – - 2690 MHzMHz 1710 2690 GSM //PCS / UMTS 2100 / LTE 2600 GSM PCS/ AWS / AWS / UMTS 2100 / LTE Accessories (order separately) Typical Attenuation Curves Clamp Set Diagram I Port 1 Port 3 734360 34 – 60 mm 734361 60 – 80 mm 734362 80 – 100 mm 734363 100 – 120 mm 734364 120 – 140 mm -40 734365 45 – 125 mm -50 Type No. Description -60 78211100 78211101 -20 380 960 -30 -90 -100 0 300 600 900 Diagram II 78210901 1710 2690 -80 DC cable kit –48 VDC DC cable kit +24 VDC -10 -70 50-Ohm load 1.5 W / indoor or outdoor Port 1 Port 3 Attenuation/dB 78410367 50-Ohm load Port 2 Port 3 0 Multiband Combiners Attenuation/dB Type No. Clamp set suitable for mast diameter of 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz Port 2 Port 3 0 -0.1 -0.2 380 960 -0.3 1710 2690 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1.0 0 300 600 900 1200 1500 1800 2100 2400 2700 3000 Frequency/MHz 78210900 275 269 276 Same-Band Combiners Hybrid Combiners Same-Band Combiner Duplex Hybrid Combiner Active Duplex Hybrid Combiner Hybrid Combiner 3-dB Couplers Hybrid Ring Junctions 277 278 Summary of Same-Band Combiner and Hybrid Combiner Types Hybrid Combiners and Couplers: Description Type No. Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 2:1 Hybrid Combiner 4:4 4,7-dB Coupler 6-dB Coupler 8-dB Coupler 10-dB Coupler 15-dB Coupler Hybrid Combiner 8:4 792699 792702 793555 78210500 78210502 78210504 78210534 78211209 78211210 78211211 78211212 78211213 78211141 Hybrid Combiner 8:4 78211142 Hybrid Combiner 12:4 78211143 Hybrid Combiner 16:4 78211144 Duplex Hybrid Combiner 78210805 Active Duplex Hybrid Combiner Same-Band Combiner Same-Band Combiner Same-Band Combiner Same-Band Combiner Same-Band Combiner Same-Band Combiner Same-Band Combiner Hybrid Ring Junction Hybrid Ring Junction Hybrid Ring Junction 3-dB Coupler 3-dB Coupler 3-dB Coupler 3-dB Coupler 78211110 78210930 78210931 78210936 78211230 78211235 78210925 78210926 K6373621 790881 791498 78210524 793506 793006 793554 New Products Frequency range 806 – 960 MHz 1700 – 2200 MHz 800 – 2200 MHz 806 – 960 MHz 1710 – 2170 MHz 698 – 2690 MHz 698 – 2600 MHz 698 – 2700 MHz 698 – 2700 MHz 698 – 2700 MHz 698 – 2700 MHz 698 – 2700 MHz 790 – 960 MHz 1710 – 2690 MHz 1710 – 1880 MHz 1920 – 2170 MHz 790 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz 790 – 960 MHz 1710 – 1880 MHz 1920 – 2200 MHz 2500 – 2690 MHz Rx: 880 – 915 MHz Tx: 925 – 960 MHz Rx: 880 – 915 MHz Tx: 925 – 960 MHz 880 – 960 MHz 880 – 960 MHz 880 – 960 MHz 1710-1880 MHz 1730-1880 MHz 1920 – 2170 MHz 1920 – 2170 MHz 806 – 960 MHz 890 – 960 MHz 1710 – 1880 MHz 698 – 2690 MHz 806 – 960 MHz 1700 – 2200 MHz 800 – 2200 MHz Max. input power Connector Page 150 W per Tx/Rx port 150 W per Tx/Rx port 150 W per Tx/Rx port 60 W at each port 60 W at each port 60 W at each port 150 W at each port 150 W at each port 150 W at each port 150 W at each port 150 W at each port 150 W at each port 75 W 7-16 7-16 7-16 7-16 7-16 7-16 7-16 N - female N - female N - female N - female N - female 7-16 280 281 282 283 284 285 286 287 287 287 287 287 288, 289 75 W 7-16 288, 289 50 W 7-16 288, 289 50 W 7-16 288, 289 250 W 7-16 290, 291 250 W 7-16 292, 293 100 W at each port 100 W at each port 100 W at each port 100 W at each port 100 W at each port 100 W at each port 100 W at each port 100 W at each port 100 W at each port 50 W at each port 150 W at each port 500 W 300 W 300 W 7-16 7-16 7-16 7-16 7-16 7-16 7-16 N N N 7-16 7-16 7-16 7-16 294, 295 296, 297 298, 299 300, 301 302, 303 304, 305 306, 307 308, 309 308, 309 308, 309 310, 311 312 313 314 279 Hybrid Combiner 2:1 806 – 960 MHz 2 x 150 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 Antenna • The frequency spacing between transmitter Port 2 Tx2/Rx2 Port 1 Tx1/Rx1 signals can be as small as required • Excellent intermodulation performance • Suitable for indoor applications • Wall or 19´´ rack mounting • DC bypass between port 1 and port 3 • External DC stop available as an accessory Technical Data Type No. Frequency range Attenuation Port 1 � Port 3 Port 2 � Port 3 Port 1 � Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 � Port 3 Port 2 Mounting Weight Packing size Dimensions (w x h x d) 25 792699 806 – 960 MHz 3.1 ±0.4 dB 3.1 ±0.4 dB > 27 dB * < 1.11 50 Ω < 150 W (with max. 16 signals) < 150 W (with max. 16 signals) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +50 °C 7-16 female Indoor Bypass (max. 2500 mA) Short circuit (External DC stop available as an accessory) Wall mounting: With 4 screws (max. 7 mm diameter) 19´´ rack mounting: To be inserted on pre-installed 19´´ sliding bars (2 height units required) 10.3 kg 510 x 410 x 100 mm 336 x 444 x 64 mm * Valid if all ports are terminated with 50-Ω loads (see diagram). 280 274 Attenuation Tx/Rx1 � Tx/Rx2 / dB Attenuation Tx1 × Tx2 / dB Typical attenuation Tx/Rx1 � Tx/Rx2 vs. Antenna VSWR 20 15 1.0 1.5 2.0 Antenna VSWR Antenna VSWR Note: The input power rating of 150 W per port is specified at an ambient temperature of +55 °C with the combiner mounted vertically (see photo), without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). When installed in a 19´´ rack, it must be ensured that the max. power of 150 W is sufficienly dissipated, so that the ambient temperature does not rise above +50 °C. This can be achieved for example by the additional installation of a correspondingly dimensioned ventilator in the 19´´ rack or by reducing the maximum input power. Hybrid Combiner 2:1 1700 – 2200 MHz 2 x 150 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 Antenna • The frequency spacing between transmitter Port 2 Tx2/Rx2 Port 1 Tx1/Rx1 signals can be as small as required • Excellent intermodulation performance • Suitable for indoor applications Technical Data Type No. Frequency range Attenuation Port 1 � Port 3 Port 2 � Port 3 Port 1 � Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 � Port 3 Port 2 Mounting Weight Packing size Dimensions (w x h x d) 792702 1700 – 2200 MHz 3.1 ±0.4 dB 3.1 ±0.4 dB > 24 dB* < 1.15 50 Ω < 150 W (with max. 16 signals) < 150 W (with max. 16 signals) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +50 °C 7-16 female Indoor Bypass (max. 2500 mA) Short circuit (External DC stop available as an accessory) Wall mounting: With 4 screws (max. 7 mm diameter) 19´´ rack mounting: To be inserted on pre-installed 19´´ sliding bars (2 height units required) 9.8 kg 510 x 410 x 100 mm 336 x 444 x 64 mm * Valid if all ports are terminated with 50-Ω loads (see diagram). Attenuation Tx/Rx1 � Tx/Rx2 / dB Typical attenuation Tx/Rx1 � Tx/Rx2 vs. Antenna VSWR Antenna VSWR Note: The input power rating of 150 W per port is specified at an ambient temperature of +55 °C with the combiner mounted vertically (see photo), without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). When installed in a 19´´ rack, it must be ensured that the max. power of 150 W is sufficienly dissipated, so that the ambient temperature does not rise above +50 °C. This can be achieved for example by the additional installation of a correspondingly dimensioned ventilator in the 19´´ rack or by reducing the maximum input power. 281 275 Same-Band / Hybrid Combiners • Wall or 19´´ rack mounting • DC bypass between port 1 and port 3 • External DC stop available as an accessory Hybrid Combiner 2:1 800 – 2200 MHz 2 x 150 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 Antenna • The frequency spacing between transmitter Port 2 Tx2/Rx2 Port 1 Tx1/Rx1 signals can be as small as required • Excellent intermodulation performance • Suitable for indoor applications • Wall or 19´´ rack mounting • DC bypass between port 1 and port 3 • External DC stop available as an accessory Hybrid Combiner 2:1 800 – 2200 MHz 2 x 150 W Hybrid Combiner 2:1 Accessories (order separately) 800 – 2200 MHz Type No. Description 2 x 150 W 793 301 DC stop Accessories (order separately) Type No. DC stop Description 793 301 DC stop Technical Data Type No. Frequency range Attenuation Port 1 � Port 3 Port 2 � Port 3 Port 1 � Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 � Port 3 Port 2 Mounting Weight Packing size Dimensions (w x h x d) 793555 800 – 2200 MHz 3.1 ±1.2 dB 3.1 ±1.2 dB > 22 dB* < 1.2 50 Ω < 150 W (with max. 16 signals) < 150 W (with max. 16 signals) < –160 dBc (3 rd order; with 2 x 20 W) –20 … +50 °C 7-16 female Indoor Bypass (max. 2500 mA) Short circuit (External DC stop available as an accessory) Wall mounting: With 4 screws (max. 7 mm diameter) 19´´ rack mounting: To be inserted on pre-installed 19´´ sliding bars (2 height units required) 10 kg 510 x 410 x 100 mm 336 x 444 x 58.5 mm * Valid if all ports are terminated with 50-Ω loads (see diagram) 282 276 Attenuation Port 1 � Port 2 / dB Typical attenuation Port 1 � Port 2 vs. VSWR at Port 3 VSWR at Port 3 Note: The input power rating of 150 W per port is specified at an ambient temperature of +55 °C with the combiner mounted vertically (see photo), without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). When installed in a 19´´ rack, it must be ensured that the max. power of 150 W is sufficienly dissipated, so that the ambient temperature does not rise above +50 °C. This can be achieved for example by the additional installation of a correspondingly dimensioned ventilator in the 19´´ rack or by reducing the maximum input power. DC stop Hybrid Combiner 2:1 806 – 960 MHz 2 x 60 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 • The frequency spacing between transmitter signals can be as small as required • Excellent intermodulation performance • Suitable for indoor or outdoor applications • Wall or mast mounting • DC bypass between all ports • External DC stop available as an accessory Port 1 Port 2 Technical Data Type No. 78210500 Frequency range Attenuation Port 1 � Port 3 Port 2 � Port 3 Port 1 � Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency 806 – 960 MHz Mounting Weight Packing size Dimensions (w x h x d) Same-Band / Hybrid Combiners 3.1 ±0.5 dB 3.1 ±0.5 dB > 23 dB * < 1.15 50 Ω < 60 W < 60 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +55 °C 7-16 female (long neck) Indoor or outdoor (IP 66) Bypass between all ports (max. 2500 mA) AISG: Attenuation 3 dB with / 6 dB without external DC stop at either Port 1 or Port 2 Wall mounting: With 4 screws (max. 6.5 mm diameter) Mast mounting: With additional clamp set (see data sheet) 3.7 kg 377 x 232 x 189 mm 143.6 x 258 x 97.5 mm (including connectors) * Valid if all ports are terminated with 50-Ω loads. Note: The input power rating of 60 W per port is specified at an ambient temperature of +55 °C with the combiner mounted horizontally, without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). If mounted vertically and/or used at a lower ambient temperature, then a higher input power in accordance with the following table is possible: Max. input power per port Max. ambient temperature +55 °C +40 °C +25 °C Mounted horizontally Mounted vertically 60 W 70 W 75 W 70 W 80 W 85 W Earth screw M8 x 10 283 277 Hybrid Combiner 2:1 1710 – 2170 MHz 2 x 60 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna Port 3 • The frequency spacing between transmitter signals can be as small as required • Excellent intermodulation performance • Suitable for indoor or outdoor applications • Wall or mast mounting • DC bypass between all ports • External DC stop available as an accessory Port 1 Port 2 Technical Data 78210502 Type No. Frequency range Attenuation Port 1 � Port 3 Port 2 � Port 3 Port 1 � Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Mounting Weight Packing size Dimensions (w x h x d) 1710 – 2170 MHz 3.1 ±0.5 dB 3.1 ±0.5 dB > 22 dB * < 1.25 50 Ω < 60 W < 60 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +55 °C 7-16 female (long neck) Indoor or outdoor (IP 66) Bypass between all ports (max. 2500 mA) AISG: Attenuation 3 dB with / 6 dB without external DC stop at either Port 1 or Port 2 Wall mounting: With 4 screws (max. 6.5 mm diameter) Mast mounting: With additional clamp set 3.7 kg 377 x 232 x 189 mm 143.6 x 256 x 97.5 mm (including connectors) * Valid if all ports are terminated with 50-Ω loads. Note: The input power rating of 60 W per port is specified at an ambient temperature of +55 °C with the combiner mounted horizontally, without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). If mounted vertically and/or used at a lower ambient temperature, then a higher input power in accordance with the following table is possible: Max. input power per port Max. ambient temperature +55 °C +40 °C +25 °C 284 278 Mounted horizontally Mounted vertically 60 W 70 W 75 W 70 W 80 W 85 W Earth screw M8 x 10 Hybrid Combiner 2:1 698 – 2690 MHz 2 x 60 W • Designed for the decoupled combining of 2 transmitter or receiver signals onto one common antenna • The frequency spacing between transmitter signals can be as small as required • Excellent intermodulation performance • Suitable for indoor or outdoor applications • Wall or mast mounting • DC bypass between port 1 and port 3 Port 1 Port 3 Port 2 Technical Data 78210504 Type No. Weight Packing size Dimensions (w x h x d) 698 – 2690 MHz 3.1 ±0.5 dB 3.1 ±0.5 dB > 23 dB* < 1.2 (698 – 2170 MHz) / < 1.25 (2170 – 2690 MHz) 50 Ω Same-Band / Hybrid Combiners Frequency range Attenuation Port 1 � Port 3 Port 2 � Port 3 Port 1 � Port 2 VSWR (all ports) Impedance Input power Port 1 Port 2 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 � Port 3 Port 2 � Port 3 Mounting < 60 W < 60 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +55 °C 7-16 female (long neck) Indoor or outdoor (IP 66) Bypass (max.2:1 2500 mA) Hybrid Combiner Stop 698Wall– mounting: 2690 MHz With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 2 x 60 W 4.3 kg 385 x 345 x 168 mm 264 x 203 x 72.5 mm (without connectors, without mounting brackets) * Valid if all ports are terminated with 50-Ohm loads. Note: The input power rating of 60 W per port is specified at an ambient temperature of +55 °C with the combiner mounted vertically, without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). If used at a lower ambient temperature, then a higher input power in accordance with the following table is possible: Max. input power per port Max. ambient temperature +55 °C +40 °C +25 °C Mounted horizontally Mounted vertically 55 W 70 W 80 W 60 W 75 W 85 W 285 279 Hybrid Combiner 4:4 698 – 2690 MHz 4 x 150 W • Designed for the decoupled combining of 4 transmitter or receiver signals and distributing these signals equally onto 4 antenna outputs Output 1 Output 2 Output 3 • Suitable for indoor or outdoor applications • DC/AISG bypass Output 4 • External DC stop available as an accessory Input 1 Input 2 Technical Data Input 3 Type No. 78210534 Frequency range Input 4 698 - 2690 MHz Insertion loss Input 1...4 ↔ Output 1...4 0.35 ± 0.15 dB Power distribution loss (excluding insertion loss) Input 1...4 ↔ Output 1...4 Typically 6.3 dB 6 ± 0.75 dB Isolation Input 1...4 ↔ Input 1...4 Output 1...4 ↔ Output 1...4 > 20 dB* > 20 dB* VSWR (all ports) < 1.22 (698 - 2170 MHz) < 1.4, typ. 1.2 (2170 - 2690 MHz) Impedance 50 Ω Input power < 150 W at each input port < -160 dBc (3rd order; with 2 x 20 W) Intermodulation products Temperature range -40 ... +60 °C Connectors 7-16 female Indoor or Outdoor (IP 66) Application DC/AISG transparency Bypass (max. 2500 mA) between Input 1 ↔ Output 4 / Input 2 ↔ Output 2 / Input 3 ↔ Output 3 / Input 4 ↔ Output 1 External DC stop available as an accessory Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With mounting kit Weight 4.5 kg Packing size 453 x 125 x 273 mm Dimensions (w x h x d) 375.9 x 65 x 224.2 mm (with connectors and mounting feet) * Valid if all ports are terminated with 50-Ohm loads Note: The use of fewer than 4 inputs or outputs is possible. Any unused input ports have to be terminated with low-power 50-Ohm loads (e.g. Kathrein type 784 10367), unused output ports have to be terminated with high-power 50-Ohm loads (e.g. Kathrein lowintermodulation type 78210474). Accessories (order separately) Type No. 78210850V01 Description DC stop 78210474 50-Ohm load (80 W) 78410367 50-Ohm load (1.5 W) 78210535 Mast mounting kit 286 DC stop 50-Ohm load 50-Ohm load 4.7-, 6-, 8-, 10-, 15-dB Coupler Hybrid Combiner 2:2 698 – 2700 MHz • Suitable for indoor or outdoor applications • DC/AISG bypass Port 1 Dimensions Port 3 10 18,75 22,7 156 Port 2 6 5 102,3 64,5 86,2 Port 4 38 92,5 Technical Data Type No. 78211209 78211210 Frequency range Attenuation Port 1 ↔ Port 2 Port 1 ↔ Port 3 Port 2 ↔ Port 3 VSWR 78211211 78211212 78211213 10.0 ± 1.0 dB 0.5 ± 0.5 dB > 20 dB 15.0 ± 1.0 dB 0.2 ± 0.2 dB > 20 dB 698 – 2700 MHz 4.7 ± 1.0 dB 2.25 ± 0.5 dB > 18 dB 6.0 ± 1.0 dB 1.75 ± 0.5 dB > 20 dB 8.0 ± 1.0 dB 0.7 ± 0.3 dB > 20 dB < 1.3 < 1.25 Impedance 50 Ω Input power < 150 W at each input port Intermodulation products Temperature range < –160 dBc (3rd order; with 2 x 20 W) -40 ... +70 °C Connectors N female Application Indoor or outdoor (IP66) DC/AISG transparency Mounting Weight Dimensions (w x h x d) Bypass between Port 1 ↔ Port 3 / Port 2 ↔ Port 4 (max. 2500 mA) With 4 screws (max. 4 mm diameter) 0.8 kg 156 x 64.5 x 22.7 (without connectors and mounting feet) Note: VSWR and attenuation values only valid if all ports are terminated with 50-Ohm loads. 287 Hybrid Combiner 8 : 4 / 8 : 4 / 12 : 4 / 16 : 4 • Designed for the decoupled combining of 8/12/16 transmitter or receiver signals and distributing these signals evenly onto 4 antenna outputs. 78211141 78211142 78211143 78211144 Technical Data Type No. Frequency range Band 1 Band 2 Band 3 Band 4 78211141 78211142 78211143 78211144 698 - 960 MHz 1710 - 2690 MHz 1710 - 1880 MHz 1920 - 2170 MHz 698 - 960 MHz 1710 - 1880 MHz 1920 - 2170 MHz 698 – 960 MHz 1710 – 1880 MHz 1920 – 2170 MHz 2500 – 2690 MHz 8:4 8:4 12 : 4 Power distribution loss (excluding insertion loss) Input 1...8/12/16 ↔ Output 1...4 6 ± 0.8 dB Insertion loss Input 1...8/12/16 ↔ Output 1...4 0.7 dB Isolation between input ports Same bands Different bands Typically 6.5 dB > 22 dB > 50 dB VSWR (all ports) < 1.5 Impedance 50 Ω Input power at each input port < 75 W < 75 W Intermodulation products < 50 W -40 ... +60 °C Connectors 7-16 female Application Indoor Weight < 50 W < -160 dBc (3rd order; with 2 x 20 W) Temperature range Mounting 16 : 4 Wall mounting: With 4 screws (max. 6 mm diameter) / 19“-drawer Approx. 12 kg Approx. 19 kg Approx. 20 kg Approx. 22,5 kg Note: The use of fewer than 8/12/16 inputs or 4 outputs is possible. Any unused input ports have to be terminated with low-power 50-Ohm loads (e.g. Kathrein type 78410367), unused output ports have to be terminated with high-power 50-Ohm loads (e.g. Kathrein low intermodulation type 78210474). 288 Hybrid Combiner 8 : 4 / 8 : 4 / 12 : 4 / 16 : 4 289 Duplex Hybrid Combiner (Same-Band Combiner) 880 – 960 MHz EGSM 900 880 – 960 MHz UMTS 900 • Enables antenna and feeder sharing for two base stations in the 900 MHz frequency band • Very low insertion loss over full EGSM/UMTS 900 Tx bandwith compared to standard hybrid combiners • Double unit in one housing for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG bypass for DTMA supply (for UMTS paths only) • Rx diversity ports protected against incorrectly connected Tx power Port 3 Port 2 Port 6 Port 1 Port 4 Port 5 Typical Attenuation Curves Attenuation/dB Diagram I Port 1 � Port 3 Port 4 � Port 6 0 5 10 925 960 880 915 15 20 25 30 35 40 45 50 870 880 890 900 910 Attenuation/dB Diagram II 920 930 940 950 960 Frequency/MHz 970 Port 1 � Port 3 Port 4 � Port 6 0 0.5 1.0 925 960 880 915 1.5 2.0 2.5 3.0 Technical Data 78210805 880 – 915 MHz 925 – 960 MHz < 0.4 dB, typically 0.2 dB (925 – 960 MHz) – see Diagram I and II < 4.3 dB, typically 3.6 dB (880 – 915 MHz) – see Diagram I and II Port 2 � Port 3 / Port 5 � Port 6 < 4.0 dB, typically 3.5 dB (880 – 915 MHz) – see Diagram III and IV Isolation Port 1 � Port 2 / Port 4 � Port 5 > 25 dB (880 – 915 MHz) > 35 dB (925 – 960 MHz) VSWR < 1.2 (880 – 915 / 925 – 960 MHz) Impedance 50 Ω Input power Port 1: < 250 W Port 2: < 50 W Port 4: < 250 W Port 5: < 50 W Intermodulation products < –160 dBc (3 rd order; with 2 x 20 W) Temperature range –40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency Port 1 � Port 3 / Port 5 � Port 6 Stop Port 2 � Port 3 / Port 4 � Port 6 Bypass (max. 2500 mA) Lightning protection 3 kA, 10/350 s pulse Mounting With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Weight 6.5 kg Packing size 390 x 470 x 160 mm Dimensions (w x h x d) 287.1 x 278.6 x 71 mm (without connectors, without mounting brackets) 290 286 4.5 5.0 870 880 890 900 910 Diagram III Attenuation/dB Pass band Rx Tx Insertion loss Port 1 � Port 3 / Port 4 � Port 6 4.0 920 930 940 950 Frequency/MHz 960 970 Port 2 � Port 3 Port 5 � Port 6 0 5 10 925 960 880 915 15 20 25 30 35 40 45 50 870 880 890 900 910 Diagram IV Attenuation/dB Type No. 3.5 920 930 940 950 Frequency/MHz 960 970 Port 2 � Port 3 Port 5 � Port 6 0 0.5 1.0 925 960 880 915 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 870 880 890 900 910 920 930 940 950 Frequency/MHz 960 970 Duplex Hybrid Combiner (Same-Band Combiner) 880 – 960 MHz EGSM 900 880 – 960 MHz UMTS 900 Accessories (order separately) Clamp set suitable for mast diameter of 734360 34 – 60 mm 734361 60 – 80 mm 734362 80 – 100 mm 734363 100 – 120 mm 734364 120 – 140 mm 734365 45 – 125 mm Type No. Description 793301 78410367 Clamp Set �� DC stop 50-Ω load DC stop 50-Ω load 1.5 W indoor or outdoor �� Same-Band / Hybrid Combiners Type No. �� Application example 291 287 734362 80 – 100 mm 734363 100 – 120 mm 734364 Active Duplex Hybrid Combiner (Same-Band Combiner) 734365 880 ... 960 MHz EGSM 900 880 ... 960 MHz UMTS 900 Type No. antenna and feeder sharing for two base stations in • Enables the 900 MHz frequency band • 12 dB gain over 20 MHz Rx bandwidth (factory tunable) low insertion loss over 20 MHz Tx bandwidth (factory • Very tunable) compared to standard hybrid combiners • Double unit in one housing for XPol antennas • Suitable for indoor or outdoor applications • Supports AISG 1.1 and AISG 2.0 (default) for antenna RET control according to AISG/3GPP • Suitable standard mode (LNA) to ensure cell operation in case of DC • Bypass power down • Built-in lightning protection Type No. Pass band Rx Tx Tx Insertion loss Port 2 � Port 3 / Port 5 � Port 6 Isolation Port 1 � Port 2 / Port 4 � Port 5 Gain Gain ripple Loss in bypass mode Return loss Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) VSWR Impedance Input power Intermodulation products Environmental Characteristics Operating temperature range IP rating MTBF EMC DC and Alarm Characteristics DC supply Operating current per TMA (without RET) Alarm management Mechanical Characteristics Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) 45 – 125 mm 50-Ω load Description 793301 DC stop Port 3 Port 6 Port 1 RET Port 2 Port 4 Port 5 78211110 20 MHz within 880 ... 915 MHz (factory tunable) 20 MHz within 925 ... 960 MHz (factory tunable) < 0.2 dB (925 – 945 MHz)* – see Diagram I and II > 25 dB (880 – 900 MHz)* > 65 dB (925 – 945 MHz)* 12 dB nominal ±1 dB < 5.5 dB (DC OFF) > 18 dB (DC ON) / > 12 dB (DC OFF) < 1.6 dB (+22 ... +28 °C) > 11 dBm > 25 dBm (typically 30 dBm) < 1.25 (880 – 900 / 925 – 945 MHz)* 50 Ω Port 2 < 200 W Port 5 < 200 W < 160 dBc (5th order, with 2 x 20 W) –40 … +65 °C IP67 (see note on page 2) > 1 000 000 hours (per TMA) According to ETS 300 342-3 CWA Mode AISG Mode 9 – 19 V 9 – 30 V 80 – 120 mA Nom. 80 20 mA at 9 V Nom. 30 mA at 30 V 170 – 200 mA AISG (see note on page 2) 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Wall mounting: with 4 screws (max. 8 mm diameter) Mast mounting: with additional clamp set 6.8 kg 460 x 375 x 135 mm 369 x 209 x 68 mm (without connectors, without mounting brackets) * Tuning version 78211110V01: Rx 880 – 900 MHz, Tx 925 – 945 MHz 292 288 120 – 140 mm RET = Remote Electrical Tilt 78410367 50-Ω load AISG = Antenna Interface 1.5 Standards Group W / indoor or outdoor CWA = Current Window Alarm Frequency ordering information: When ordering please specify the required Tx-and Rx-frequencies Examples of tuning versions: 78211110V01: Rx 880 – 900 MHz, Tx 925 – 945 MHz 78211110V02: Rx 895 – 915 MHz, Tx 940 – 960 MHz Other frequencies on request. Technical Data DC stop RET Application example Active Duplex Hybrid Combiner (Same-Band Combiner) 880 ... 960 MHz UMTS 900 Clamp set suitable for mast diameter of 734360 34 – 60 mm 734361 60 – 80 mm 734362 80 – 100 mm 734363 100 – 120 mm 734364 120 – 140 mm 734365 45 – 125 mm Type No. Description DC stop Tuning example 78211110V01 Rx: 880 – 900 MHz, Tx: 925 – 945 MHz Port 2 Port 3 Diagram I 50-Ω load 15 10 880 900 5 925 945 0 DC stop -5 Attenuation/dB 50-Ω load 1.5 W / indoor or outdoor Port 5 Port 6 20 -10 -15 -20 -25 -30 870 880 890 900 910 920 Attenuation/dB Diagram II 930 940 950 Frequency/MHz 960 970 Port 2 Port 3 Port 5 Port 6 0 -0.5 -1.0 880 900 -1.5 925 945 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 870 880 890 900 910 920 Diagram III 930 940 950 Frequency/MHz 960 970 Port 1 Port 3 Port 4 Port 6 20 Gain/dB 78410367 Typical Attenuation Curves 15 10 880 900 5 925 945 0 -5 RET -10 -15 -20 -25 -30 870 880 890 900 910 920 Diagram IV 930 940 950 Frequency/MHz 960 970 Port 1 Port 3 Port 4 Port 6 15.0 14.5 14.0 880 900 13.5 925 945 13.0 12.5 12.0 11.5 11.0 Gain/dB 793301 Clamp Set Attenuation/dB Type No. Same-Band / Hybrid Combiners Accessories (order separately) Gain/dB 880 ... 960 MHz EGSM 900 10.5 10.0 870 880 890 900 910 920 930 940 950 Frequency/MHz 960 970 Application example 293 289 Same-Band Combiner 880 - 915 / 925 - 960 MHz GSM 900 880 - 915 / 925 - 960 MHz LTE / UMTS 900 (5 MHz Bandwidth) • Enables antenna and feeder sharing for two base stations in the same frequency band Port 1 • Suitable for two operators with frequency allocations within the same frequency band Port 3 • Customized 5 MHz Tx/Rx pass-band filters (factory tunable) available for inserting LTE/UMTS 900 base station • Full pass-band (without LTE/UMTS 900 5 MHz Tx/Rx frequency blocks) available for GSM 900 base station Port 2 Port 4 Port 6 Port 5 • Very low insertion loss over complete EGSM Tx/Rx bandwidth compared to standard hybrid combiners • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Tuning Examples Frequency ordering information: When ordering please specify the required Tx- and Rxfrequencies e.g. (tuning example 2) Rx1/Rx2 880 – 892 / 903 – 915 MHz, Rx3/Rx4 895 – 900 MHz Technical Data Type No. Pass band GSM 900 LTE/UMTS 900 Guard band Insertion loss Port 1 ↔ Port 3 / Port 4 ↔ Port 6 Port 2 ↔ Port 3 / Port 5 ↔ Port 6 Isolation Port 1 ↔ Port 2 VSWR Group delay variation GSM 900 LTE/UMTS 900 Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range Tx1/Tx2 925 – 937 / 948 – 960 MHz, Tx3/Tx4 940 – 945 MHz 78210930 Rx = 880 – 915 / Tx = 925 – 960 MHz (without assigned LTE/UMTS 900 5 MHz TX/Rx frequency blocks and ± 3 MHz guard bands) Rx = 880 ... 915 / Tx = 925 ... 960 MHz (factory tunable 5 MHz frequency blocks) 3 MHz (between Tx/Rx1 and Tx/Rx3, between Tx/Rx2 and Tx/Rx4) – e.g. tuning example 2: Rx1 (Rx2) = 880 – 892 / 903 – 915 and Tx1 (Tx2) = 925 – 937 / 948 – 960 MHz Rx3 (Rx4) = 895 – 900 and Tx3 (Tx4) = 940 – 945 MHz < 0.6 dB (typically 0.2 dB) – see diagram I and II for tuning example 2 < 0.6 dB (typically 0.4 dB) – see diagram III and IV for tuning example 2 > 30 dB (880 – 915 / 925 – 960 MHz) < 1.25 (pass bands) < 20 ns (200 kHz) < 50 ns (5 MHz) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < -160 dBc (3rd order; with 2 x 20 W) -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency (switchable) Port 1 ↔ Port 3 / Port 4 ↔ Port 6 (default) Port 2 ↔ Port 3 / Port 5 ↔ Port 6 (default) Stop By-pass (max. 2500 mA) Lightning protection Mounting Weight Packing size Dimensions (w x h x d) 294 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: 2 clamps needed 26 kg 685 x 645 x 252 mm 504 x 409 x 158.3 mm (without connectors, without mounting brackets) Same-Band Combiner Same-Band Combiner 880 - 915 / 925 - 960 MHz 880 - 915 / 925 - 960 MHz GSM 900 880 - 915 / 925 - 960 MHz GSM 900 LTE / UMTS 900 (5 MHz Bandwidth) 880 - 915 / 925 - 960 MHz LTE / UMTS 900 (5 MHz Bandwidth) Typical Attenuation Curves (Tuning Example 2) BTS 1 (GSM 900) Diagram I (Port 1 ↔ Port 3 / Port 4 ↔ Port 6) Diagram II (Port 1 ↔ Port 3 / Port 4 ↔ Port 6) Accessories (order separately) Type No. (Clamp) 731651 738546 85010002 85010003 Suitable for mast diameter 28 - 60 mm 42 - 115 mm 110 - 220 mm 210 - 380 mm Antenna – mast distance 25 - 28 mm 20 - 26 mm 47 - 55 mm 48 - 68 mm 1 clamp 1 clamp 1 clamp 1 clamp 0.8 kg 1.1 kg 2.7 kg 4.8 kg Number of pieces Weight 50-Ohm load Description 78410367 50-Ohm load 936.4222a Diagram IV (Port 2 ↔ Port 3 / Port 5 ↔ Port 6) Type No. Subject to alteration. BTS 2 (LTE/UMTS 900) Diagram III (Port 2 ↔ Port 3 / Port 5 ↔ Port 6) Page 2 of 2 78210930 www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 295 Same-Band Combiner 880 - 915 / 925 - 960 MHz GSM 900 880 - 915 / 925 - 960 MHz LTE / UMTS 900 (5 MHz Bandwidth) Block Diagram • Enables antenna and feeder sharing for two base stations in the same frequency band • Suitable for two operators with frequency allocations within the same frequency band • Customized 5 MHz Tx/Rx pass-band lters (factory tunable) available for inserting LTE/ UMTS 900 base station • Full pass-band (without LTE/UMTS 900 5 MHz Tx/Rx frequency blocks) available for GSM 900 base station • Very low insertion loss over complete EGSM Tx/Rx bandwidth compared to standard hybrid combiners • Single unit • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Tuning Examples Frequency ordering information: When ordering please specify the required Tx- and Rxfrequencies e.g. (tuning example 2) Rx1 880 - 892 / 903 - 915 MHz, Rx2 895 - 900 MHz Tx1 925 - 937 / 948 - 960 MHz, Tx2 940 - 945 MHz Technical Data Type No. Pass band GSM 900 LTE/UMTS 900 Guard band Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3 Isolation Port 1 ↔ Port 2 VSWR 936.4368 Subject to alteration. Group delay variation GSM 900 LTE/UMTS 900 Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range 78210931 Rx = 880 – 915 / Tx = 925 – 960 MHz (without assigned LTE/UMTS 900 5 MHz TX/Rx frequency blocks and ± 3 MHz guard bands) Rx = 880 ... 915 / Tx = 925 ... 960 MHz (factory tunable 5 MHz frequency blocks) 3 MHz (between Tx1/Rx1 and Tx2/Rx2) – e.g. tuning example 2: Rx1 = 880 – 892 / 903 – 915 and Tx1 = 925 – 937 / 948 – 960 MHz Rx2 = 895 – 900 and Tx2 = 940 – 945 MHz < 0.6 dB (typically 0.2 dB) – see diagram I and II for tuning example 2 < 0.6 dB (typically 0.4 dB) – see diagram III and IV for tuning example 2 > 30 dB (880 – 915 / 925 – 960 MHz) < 1.25 (pass bands) < 20 ns (200 kHz) < 50 ns (5 MHz) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < -160 dBc (3rd order; with 2 x 20 W) -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency (switchable) Port 1 ↔ Port 3 / Port 4 ↔ Port 6 (default) Port 2 ↔ Port 3 / Port 5 ↔ Port 6 (default) Stop By-pass (max. 2500 mA) Lightning protection Mounting Weight Packing size Dimensions (w x h x d) www.kathrein.de 3 kA, 10/350 μs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: 2 clamps needed 13 kg 395 x 685 x 252 mm 244 x 408 x 144 mm (without connectors, without mounting brackets) 78210931 Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 296 Same-Band Combiner 880 - 915 / 925 - 960 MHz 880 - 915 / 925 - 960 MHz GSM 900 LTE / UMTS 900 (5 MHz Bandwidth) Typical Attenuation Curves (Tuning Example 2) BTS 1 (GSM 900) Diagram I (Port 1 ↔ Port 3) Diagram II (Port 1 ↔ Port 3) Accessories (order separately) Type No. (Clamp) 731651 738546 85010002 85010003 Suitable for mast diameter 28 - 60 mm 42 - 115 mm 110 - 220 mm 210 - 380 mm Antenna – mast distance 25 - 28 mm 20 - 26 mm 47 - 55 mm 48 - 68 mm 1 clamp 1 clamp 1 clamp 1 clamp 0.8 kg 1.1 kg 2.7 kg 4.8 kg Number of pieces Weight Type No. Description 78410367 50-Ohm load 50-Ohm load 936.4368 Subject to alteration. BTS 2 (LTE/UMTS 900) Diagram III (Port 2 ↔ Port 3) Diagram IV (Port 2 ↔ Port 3) Page 2 of 2 78210931 www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 297 Same-Band Combiner - 890/ /925 925 -–935 880880 – 890 935MHz MHz GSM 900(10 (10MHz MHzBandwidth) Bandwidth) GSM900 902,5 - 915 / 947,5 – - 960 902.5 – 915 / 947.5 960MHz MHz GSM 900 (12,5 MHzBandwidth) Bandwidth) GSM900 (12.5 MHz • Enables antenna and feeder sharing for two base stations in the same frequency band • Suitable for two operators with frequency allocations within the same frequency band • Very low Tx/Rx insertion loss compared to standard hybrid combiners • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG bypass for DTMA supply Port 3 Port 2 Port 6 Port 4 Port 5 Port 1 Block Diagram Tuning Diagram Technical Data Type No. Pass band BTS 1 (GSM900 / Operator 1) BTS 2 (GSM900 / Operator 2) Insertion loss Port 1 � Port 3 / Port 4 � Port 6 Port 2 � Port 3 / Port 5 � Port 6 Isolation Port 1 � Port 2 / Port 4 � Port 5 VSWR Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 � Port 3 / Port 4 � Port 6 Port 2 � Port 3 / Port 5 � Port 6 Lightning protection Mounting Weight Dimensions (w x h x d) 298 296 78210936 Rx1/Rx2 = 880 – 890 MHz, Tx1/Tx2 = 925 – 935 MHz Rx3/Rx4 = 902.5 – 915 MHz, Tx3/Tx4 = 947.5 – 960 MHz < 0.5 dB, typically 0.3 dB (880 – 890 MHz) / < 0.7 dB, typically 0.4 dB (925 – 935 MHz) < 0.7 dB, typically 0.5 dB (902.5 – 915 MHz) / < 0.5 dB, typically 0.3 dB (947.5 – 960 MHz) > 30 dB (880 – 890 / 902.5 – 915 / 925 – 935 / 947.5 – 960 MHz) < 1.2 (pass bands) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < –160 dBc (3rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) Indoor or outdoor (IP66) Stop Bypass (max. 2500 mA) 3 kA, 10/350 s pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 6.9 kg 275 x 176 x 140 mm (without connectors, without mounting brackets) Same-Band Combiner 902,5 - 915 / 947,5 – - 960 902.5 – 915 / 947.5 960MHz MHz - 890/ /925 925 -–935 880880 – 890 935MHz MHz GSM 900 (12,5 MHzBandwidth) Bandwidth) GSM900 (12.5 MHz GSM 900(10 (10MHz MHzBandwidth) Bandwidth) GSM900 734361 60 – 80 mm 734362 80 – 100 mm 734363 100 – 120 mm 734364 120 – 140 mm 734365 45 – 125 mm Type No. Description 78410367 50-Ohm load Clamp Set 50-Ohm load Diagram I (Port 1 � Port 3 / Port 4 � Port 6) Diagram III (Port 2 � Port 3 / Port 5 � Port 6) 0 -5 -10 880 890 Rx1/Rx2 Attenuation/dB 34 – 60 mm BTS 2 (GSM900) 925 935 Tx1/Tx2 -15 0 -5 -10 -20 -25 -25 -30 -30 -35 -35 -40 -40 -45 -45 -50 870 880 890 900 910 920 930 940 950 Frequency/MHz 960 Diagram II (Port 1 � Port 3 / Port 4 � Port 6) 0 -0.5 -1.0 -1.5 880 890 Rx1/Rx2 -50 870 970 925 935 Tx1/Tx2 -1.0 -2.5 -3.0 -3.5 -3.5 -4.0 -4.0 -4.5 -4.5 910 920 930 940 950 Frequency/MHz 960 970 910 920 930 940 950 Frequency/MHz 902.5 915 Rx3/Rx4 -1.5 -3.0 900 900 960 970 0 -2.0 890 890 -0.5 -2.5 880 880 947.5 960 Tx3/Tx4 Diagram IV (Port 2 � Port 3 / Port 5 � Port 6) -2.0 -5.0 870 902.5 915 Rx3/Rx4 -15 -20 Attenuation/dB 734360 BTS 1 (GSM900) Attenuation/dB Clamp set suitable for mast diameter of Attenuation/dB Type No. Typical Attenuation Curves -5.0 870 880 890 900 910 947.5 960 Tx3/Tx4 920 930 940 950 Frequency/MHz 960 970 299 297 Same-Band / Hybrid Combiners Accessories (order separately) Same-Band Combiner 1710 – 1740 / 1805 – 1835 MHz LTE / GSM 1800 (30 MHz Bandwidth) 1755 – 1785 / 1850 – 1880 MHz LTE / GSM 1800 (30 MHz Bandwidth) • Enables antenna and feeder sharing for two base stations in the same frequency band • Suitable for two operators with frequency allocations within the same frequency band • Very low Tx/Rx insertion loss compared to standard hybrid combiners • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Double Unit 78211230 Technical Data Type No. 78211230 Double Unit Pass band BTS 1 (GSM1800 / Operator 1) BTS 2 (GSM1800 / Operator 2) Rx1/Rx2 = 1710 – 1740 MHz, Tx1/Tx2 = 1805 – 1835 MHz Rx3/Rx4 = 1755 – 1785 MHz, Tx3/Tx4 = 1850 – 1880 MHz Insertion loss Port 1 ↔ Port 3 / Port 4 ↔ Port 6 Port 2 ↔ Port 3 / Port 5 ↔ Port 6 < 0.6 dB (1710 - 1740 MHz) / < 0.5 dB (1805 - 1835 MHz) < 0.5 dB (1755 - 1785 MHz) / < 0.6 dB (1850 - 1880 MHz) Isolation Port 1 ↔ Port 2 / Port 4 ↔ Port 5 > 30 dB (1710 - 1740 / 1755 - 1785 / 1805 - 1835 / 1850 - 1880 MHz) VSWR Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range < 1.25 (pass bands) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < -160 dBc (3rd order; with 2 x 20 W) -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency (switchable) Port 1 ↔ Port 3 / Port 4 ↔ Port 6 Port 2 ↔ Port 3 / Port 5 ↔ Port 6 Stop By-pass (max. 2500 mA) Lightning protection Mounting Dimensions (w x h x d) 300 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Approx. 260 x 200 x 80 mm (without connectors, without mounting brackets) Same-Band Combiner 1710 – 1740 / 1805 – 1835 MHz LTE / GSM 1800 (30 MHz Bandwidth) 1755 – 1785 / 1850 – 1880 MHz LTE / GSM 1800 (30 MHz Bandwidth) Block Diagram Calculated Attenuation Curves BTS 1 (GSM 1800) Diagram I (Port 1 ↔ Port 3 / Port 4 ↔ Port 6) Frequency/MHz LTE / GSM 1800 LTE / GSM 1800 Diagram II (Port 1 ↔ Port 3 / Port 4 ↔ Port 6) 78211230 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. Description 78410367 50-Ohm load Clamp Set Frequency/MHz BTS 2 (GSM 1800) Diagram III (Port 2 ↔ Port 3 / Port 5 ↔ 6) 50-Ohm load Frequency/MHz Diagram IV (Port 2 ↔ Port 3 / Port 5 ↔ Port 6) Frequency/MHz 301 Same-Band Combiner 1730 – 1750.1/ 1825 – 1845.1 MHz 1764.9 – 1785 / 1859.9 – 1880 MHz LTE / GSM 1800 (20 MHz Bandwidth) LTE / GSM 1800 (20 MHz Bandwidth) • Enables antenna and feeder sharing for two base stations in the same frequency band • Suitable for two operators with frequency allocations within the same frequency band • Very low Tx/Rx insertion loss compared to standard hybrid combiners • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Tuning Examples Technical Data Type No. 78211235 Double Unit Pass band BTS 1 (GSM1800 / Operator 1) BTS 2 (GSM1800 / Operator 2) Rx1/Rx2 = 1730 – 1750.1 MHz, Tx1/Tx2 = 1825 – 1845.1 MHz Rx3/Rx4 = 1764.9 – 1785 MHz, Tx3/Tx4 = 1859.9 – 1880 MHz Insertion loss Port 1 ↔ Port 3 / Port 4 ↔ Port 6 Port 2 ↔ Port 3 / Port 5 ↔ Port 6 < 0.6 dB (1730 – 1750.1 MHz) / < 0.5 dB (1825 – 1845.1 MHz) < 0.5 dB (1764.9 – 1785 MHz) / < 0.6 dB (1859.9 – 1880 MHz) Isolation Port 1 ↔ Port 2 / Port 4 ↔ Port 5 > 30 dB (1730 – 1750.1 / 1764.9 – 1785 / 1825 – 1845.1 / 1859.9 – 1880 MHz) VSWR Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range < 1.25 (pass bands) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < -160 dBc (3rd order; with 2 x 20 W) -40 ... +60 °C Connectors 7-16 female (long neck) Application Indoor or outdoor (IP 66) DC/AISG transparency (switchable) Port 1 ↔ Port 3 / Port 4 ↔ Port 6 Port 2 ↔ Port 3 / Port 5 ↔ Port 6 Stop By-pass (max. 2500 mA) Lightning protection Mounting Dimensions (w x h x d) 302 3 kA, 10/350 µs pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set Approx. 260 x 200 x 80 mm (without connectors, without mounting brackets) Same-Band Combiner 1730 – 1750.1/ 1825 – 1845.1 MHz LTE / GSM 1800 (20 MHz Bandwidth) 1764.9 – 1785 / 1859.9 – 1880 MHz LTE / GSM 1800 (20 MHz Bandwidth) Block Diagram LTE / GSM 1800 LTE / GSM 1800 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Type No. Description 78410367 50-Ohm load Clamp Set 50-Ohm load 303 Same-Band Combiner 1920 – 1980 / 2110 – 2170 MHz UMTS 2100 • • • • • • • 1920 ... 1980 / 2110 ... 2170 MHz UMTS 2100 (10 MHz Bandwidth) Enables antenna and feeder sharing for two base stations in the same frequency band Customized 10 MHz Tx/Rx bandpass filters (factory tunable) available for inserting a second UMTS 2100 base station Port 2 Full pass-band (without the second UMTS 2100 10 MHz Tx/Rx frequency blocks) available for the first UMTS 2100 base station Low insertion loss over complete UMTS 2100 Tx/Rx bandwidth compared to standard hybrid combiners Double unit for XPol antennas Port 1 Port 6 Port 3 Port 4 Suitable for indoor or outdoor applications DC/AISG by-pass for DTMA supply Port 5 Frequency ordering information: When ordering please specify the required Tx- and Rx-frequencies e.g. (tuning example 1) Rx1/Rx2 1950 – 1965 MHz, Rx3/Rx4 1970 – 1980 MHz TX1/Tx2 2140 – 2155 MHz, TX3/Tx4 2160 – 2170 MHz Block Diagram Tuning Examples 1 2 3 Technical Data Type No. Pass band BTS 1 (UMTS 2100) BTS 2 (UMTS 2100) 936.4181/c Subject to alteration. Guard band 78210925 Rx = 1920 – 1980 / Tx = 2110 – 2170 MHz (without assigned BTS 2 10 MHz Tx/Rx frequency blocks and ±5 MHz guard bands) Rx = 1920 ... 1980 / Tx = 2110 ... 2170 MHz (factory tunable 10 MHz frequency blocks) 5 MHz (between Tx1/Rx1 and Tx3/Rx3, between Tx2/Rx2 and Tx4/Rx4 e.g. tuning example 1: Rx1 (Rx2) = 1950 – 1965 and Tx1 (Tx2) = 2140 – 2155 MHz Rx3 (Rx4) = 1970 – 1980 and Tx3 (Tx4) = 2160 – 2170 MHz Insertion loss Port 1 Port 3 / Port 4 Port 6 Port 2 Port 3 / Port 5 Port 6 < 1.2 dB – see diagram I and II for tuning example 1 < 1.2 dB – see diagram III and IV for tuning example 1 Isolation Port 1 Port 2 / Port 4 Port 5 > 30 dB (1920 – 1980 / 2110 – 2170 MHz) VSWR Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 Port 3 / Port 4 Port 6 Port 2 Port 3 / Port 5 Port 6 Lightning protection Mounting Weight Packing size Dimensions (w x h x d) www.kathrein.de < 1.25 (pass bands) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) Indoor or outdoor (IP66) Stop By-pass (max. 2500 mA) 3 kA, 10/350 s pulse Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 7 kg 425 x 315 x 180 mm 243 x 240 x 100 mm (without connectors, without mounting brackets) 78210925 Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 304 Same-Band Combiner 1920 – 1980 / 2110 – 2170 MHz 1920 ... 1980 / 2110 ... 2170 MHz UMTS 2100 UMTS 2100 (10 MHz Bandwidth) Accessories (order separately) 34 – 60 mm 734 361 60 – 80 mm 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 734 365 45 – 125 mm Type No. 78410367 BTS 2 (UMTS 2100) BTS 1 (UMTS 2100) Diagram I (Port 1 Port 3 / Port 4 Port 6) Description 50-Ohm load 0 5 1950 – 1965 Rx 10 15 0 5 10 1970 – 1980 Rx 20 25 25 30 30 35 35 40 40 45 45 50 1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200 2160 – 2170 Tx 15 20 50 1900 1930 1960 1990 Clamp Set 50-Ohm load 2140 – 2155 Tx Diagram III (Port 2 Port 3 / Port 5 6) Attenuation/dB 734 360 734 362 Typical Attenuation Curves (Tuning Example 1) Clamp set suitable for mast diameter of Attenuation/dB Type No. 2020 2050 2080 2110 2140 2170 2200 Frequency/MHz Frequency/MHz 0.5 1.0 1950 – 1965 Rx 2140 – 2155 Tx 1.5 Diagram IV (Port 2 Port 3 / Port 5 Port 6) Attenuation/dB Attenuation/dB Diagram II (Port 1 Port 3 / Port 4 Port 6) 0 0 0.5 1.0 1.5 2.0 2.0 2.5 2.5 3.0 3.0 3.5 3.5 4.0 4.0 4.5 4.5 5.0 1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200 2160 – 2170 Tx 1970 – 1980 Rx 5.0 1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200 Frequency/MHz Frequency/MHz Please note: These facts must be considered during the site planning process. The Same-band Combiner is designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E and have passed environmental tests as recommended in ETS 300 019-2-4. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas, filters, combiners, amplifiers and accessories. The limits for the coupling torque of RF connectors, recommended by the connector manufacturers must be obeyed. Terminate unused inputs with a suitable 50-Ohm load, e.g. 784 10367. Any previous datasheet issues have now become invalid. Page 2 of 2 78210925 www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 305 936.4181/c Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of a mast mounted device or even cause it to fall to the ground. Subject to alteration. As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. Same-Band Combiner 1920 – 1980 / 2110 – 2170 MHz UMTS 2100 1920 ... 1980 / 2110 ... 2170 MHz UMTS 2100 (15 MHz Bandwidth) • Enables antenna and feeder sharing for two base stations in the same frequency band • Customized 15 MHz Tx/Rx bandpass filters (factory tunable) available for inserting a second UMTS 2100 base station Full • pass-band (without the second UMTS 2100 15 MHz Tx/Rx frequency blocks) available for the first UMTS 2100 base station Low insertion loss over complete UMTS 2100 Tx/Rx band• width compared to standard hybrid combiners • Double unit for XPol antennas • Suitable for indoor or outdoor applications • DC/AISG by-pass for DTMA supply Port 2 Port 1 Port 6 Port 3 Port 4 Port 5 Block Diagram Frequency ordering information: When ordering please specify the required Tx- and Rx-frequencies e.g. (tuning example 1) Rx1/Rx2 1935 – 1950 MHz, Rx3/Rx4 1965 – 1980 MHz, Tx1/Tx2 2125 – 2140 MHz, Tx3/Tx4 2155 – 2170 MHz Tuning Examples 1 2 Technical Data 78210926 Type No. Pass band BTS 1 (UMTS 2100) Rx = 1920 – 1980 / Tx = 2110 – 2170 MHz (without assigned BTS 2 15 MHz Tx/Rx frequency blocks and ±15 MHz guard bands) Rx = 1920 ... 1980 / Tx = 2110 ... 2170 MHz (factory tunable 15 MHz frequency blocks) 15 MHz (between Tx1/Rx1 and Tx3/Rx3, between Tx2/Rx2 and Tx4/Rx4 e.g. tuning example 1: Rx1 (Rx2) = 1935 – 1950 and Tx1 (Tx2) = 2125 – 2140 MHz Rx3 (Rx4) = 1965 – 1980 and Tx3 (Tx4) = 2155 – 2170 MHz BTS 2 (UMTS 2100) Guard band Insertion loss Port 1 � Port 3 / Port 4 Port 2 � Port 3 / Port 5 Isolation Port 1 � Port 2 / Port 4 VSWR Impedance Input power Tx1 / Tx2 / Tx3 / Tx4 Intermodulation products Temperature range Connectors Application DC/AISG transparency Port 1 � Port 3 / Port 4 Port 2 � Port 3 / Port 5 Lightning protection Packing size Mounting Weight Dimensions (w x h x d) 306 292 � Port 6 � Port 6 < 1.2 dB < 1.2 dB � Port 5 > 28 dB (1920 – 1980 / 2110 – 2170 MHz) < 1.25 (pass bands) 50 Ω < 100 W / < 100 W / < 100 W / < 100 W < –160 dBc (3 rd order; with 2 x 20 W) –40 … +60 °C 7-16 female (long neck) Indoor or outdoor (IP66) � Port 6 � Port 6 Stop By-pass (max. 2500 mA) 3 kA, 10/350 s pulse 425 x 315 x 180 mm Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 7 kg 246 x 256 x 102 mm (without connectors, without mounting brackets) Same-Band Combiner 1920 – 1980 / 2110 – 2170 MHz 1920 ... 1980 / 2110 ... 2170 MHz UMTS 2100 UMTS 2100 (15 MHz Bandwidth) Accessories (order separately) Typical Attenuation Curves (Tuning Example 1) Type No. Clamp set suitable for mast diameter of 734 360 34 – 60 mm 734 361 60 – 80 mm 734 362 80 – 100 mm 734 363 100 – 120 mm 734 364 120 – 140 mm 20 20 734 365 45 – 125 mm 25 25 30 30 35 35 40 40 45 45 78410367 50-Ohm load 10 15 1935 – 1950 Rx 50 1900 1930 1960 1990 Clamp Set 50-Ohm load 2125 – 2140 Tx Frequency/MHz Attenuation/dB 0 0.5 1.5 1935 – 1950 Rx 2125 – 2140 Tx 0 5 10 15 Frequency/MHz 0 1.0 1.5 2.5 2.5 3.0 3.0 3.5 3.5 4.0 4.0 4.5 4.5 Frequency/MHz 2020 2050 2080 2110 2140 2170 2200 0.5 2.0 2020 2050 2080 2110 2140 2170 2200 2155 – 2170 Tx Diagram IV (Port 2 � Port 3 / Port 5 � Port 6) 2.0 5.0 1900 1930 1960 1990 1965 – 1980 Rx 50 1900 1930 1960 1990 2020 2050 2080 2110 2140 2170 2200 Diagram II (Port 1 � Port 3 / Port 4 � Port 6) 1.0 Attenuation/dB Attenuation/dB 5 Diagram III (Port 2 � Port 3 / Port 5 � 6) 1965 – 1980 Rx 5.0 1900 1930 1960 1990 2155 – 2170 Tx 2020 2050 2080 2110 2140 2170 2200 Frequency/MHz 307 293 Same-Band / Hybrid Combiners Description Diagram I (Port 1 � Port 3 / Port 4 � Port 6) 0 Attenuation/dB Type No. BTS 2 (UMTS 2100) BTS 1 (UMTS 2100) Hybrid Ring Junction (180° Hybrid) 806 – 960 MHz / 1710 – 1880 MHz The hybrid ring junction can be used: • as a power splitter with a ratio of 1:1, • for the decoupled combining of two transmitters with arbitrarily low frequency spacing ( at 3 dB loss), • for the decoupled combining of two receivers with arbitrarily low frequency spacing, • for the decoupled combining of two transmitter/receiver units, whose integrated duplexers are within the same frequency range, Port 1 Port 2 Port 3 • as component to form combiners. Port 4 K6373621 790881 Description: The hybrid ring junction has four ports, two of which are decoupled from each other. For example effective power entering into port 1 is distributed into ports 2 and 4, port 3 is decoupled and without power if ports 2 and 4 are ideally matched. In practice an absorber of suitable power at port 3 is to be planned for according to the mismatch of ports 2 and 4. Decoupled combining can be made via ports 1 and 3 or 2 and 4. 2 λ /4 Port 4 Port 1 Port 3 Port 2 λ /4 1 3 λ /4 3/4λ 4 Technische Daten Typ Nr. K6373621 790881 791498 Frequency range 806 - 960 MHz 890 - 960 MHz 1710 - 1880 MHz Attenuation 1 ↔ 2 or 1 ↔ 4 3.1 ±0.4 dB (see diagram I) 3 ±0.3 dB (see diagram I) 3 ±0.4 dB (see diagram I) Attenuation 1 ↔ 3 or 2 ↔ 4 See diagram II See diagram II > 25 dB VSWR < 1.2 < 1.3 Impedance 50 Ω 50 Ω Input power < 100 W per input < 50 W per input Connectors N female N female Application Indoor Indoor With 2 screws (max. 4.5 mm diameter) With 4 screws (max. 4.5 mm diameter) 0.32 kg 0.25 kg Approx. 160 mm x 40 mm x 105 mm 90 mm x 40 mm x 110 mm 150 mm x 30 mm x 87 mm (including connectors) 80 mm x 26 mm x 106 mm (including connectors) Mounting Weight Packing size Dimensions (w x h x d) Note: VSWR and attenuation values are measured when the remaining ports are terminated with 50-Ω loads 308 Hybrid Ring Junction (180° Hybrid) 806 – 960 MHz / 1710 – 1880 MHz Typical Attenuation Curves K6373621 Diagram I Diagram I Diagram II 790881 Diagram II 791498 Diagram I 309 3-dB Coupler Hybrid Combiner 2 : 2 698 – 2690 MHz • Can be used for the decoupled combining of 2 transmitters Port 1 onto a common antenna with frequency spacing as narrow as desired (3 dB loss) – see application example 1 Port 3 • Can be used for the decoupled combining of 2 transmitters onto two antennas with frequency spacing as narrow as desired – see application example 2 • Can be used as a decoupled 2-way splitter – see application example 3 Port 2 • Can be used as a frequency-independant 90° phase shifter (90° Hybrid) Port 4 • Suitable for indoor or outdoor applications • DC/AISG by-pass • External DC stop available as an accessory Diagram Technical Data Type No. 782 10524 Frequency range Attenuation Port 1 Port 2 Port 1 Port 3 Port 2 Port 3 698 – 2690 MHz Directivity VSWR 936.4198 Subject to alteration. Impedance Input power Intermodulation products Temperature range Connectors Application DC/AISG transparency 3.1 ±0.5 dB 3.1 ±0.5 dB See diagram ↔ ↔ > 20 dB < 1.25 < –160 dBc (3 rd order; with 2 x 20 W) 50 Ω < 150 W at each input port Accessories (order separately) –40 ... +70 °C 7-16 female Indoor or outdoor (IP66) By-pass between Port 1 Port 3 / Port 2 Port 4 (max. 2500 mA) External DC stop available as an accessory Mounting Weight With 4 screws (max. 6.5 mm diameter) 1.5 kg Packing size Dimensions (w x h x d) 268 x 115 x 203 mm 205.4 x 60 x 104 mm (without connectors and mounting feet) Type No. 782 10850V01 10850 782 Description DC stop 782 10474 50-Ohm load (80 W) 784 10367 50-Ohm load (1.5 W) DC stop 50-Ohm load 50-Ohm load Note: VSWR and attenuation values only valid if all ports are terminated with 50-Ohm loads. www.kathrein.de 782 10524 Page 1 of 2 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 310 3-dB Coupler Hybrid Combiner 2 : 2 698 – 2690 MHz Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of a mast mounted device or even cause it to fall to the ground. These facts must be considered during the site planning process. The 3-dB Coupler is designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E and have passed environmental tests as recommended in ETS 300 019-2-4. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the coupler and accessories. The limits for the coupling torque of RF connectors, recommended by the connector manufacturers must be obeyed. Any previous datasheet issues have now become invalid. Page 2 of 2 782 10524 www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 311 936.4198 As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. Subject to alteration. Please note: 3-dB Coupler Hybrid Combiner 2:2 806 – 960 MHz The 3-dB coupler can be used: – as a decoupled power splitter with a ratio of 1:1, – for the decoupled combining of two transmitters with frequency spacing as narrow as desired (at 3 dB loss), – for the decoupled combining of two receivers with frequency spacing as narrow as desired, – for the decoupled combining of two transmitter/receiver units, whose integrated duplexers are within the same frequency range, – as a frequency-independent 90° phase shifter, – as a component to form combiners. earth screw M6 Intermodulation products Temperature range Connectors Application Mounting Weight Packing size Dimensions (w x h x d) 806 – 960 MHz 3 ±0.4 dB (see diagram I) See diagram II > 30 dB < 1.1 50 Ω < 500 W total power at two inputs, with max. 350 W at one input < –160 dBc (3 rd order; with 2 x 20 W) –30 ... +70 °C 7-16 female Indoor or outdoor (IP66) With 2 screws (max. 6 mm diameter) 1.8 kg 160 x 95 x 65 mm 136 x 46.5 x 94 mm (including connectors) 12 3.0 13 3.5 Frequency/MHz 1 3 2 4 960 Diagram II 793506 Note: VSWR and attenuation values are measured when the remaining ports are terminated with 50-Ω loads. 312 302 2.5 806 Typical attenuation 2 3 vs. VSWR at port 1 Attenuation 2 3 / dB Frequency range Attenuation 1 � 2 1 � 3 Attenuation 2 � 3 Directivity VSWR Impedance Input power Typical attenuation between ports 1 2 resp. 1 3 vs. frequency coupler 7-16 Technical Data Type No. Attenuation 1 3 / dB Diagram I Attenuation 1 2 / dB Function: The 3-dB coupler has four ports, two of which are decoupled from each other. For example effective power entering into port 1 is distributed into ports 2 and 3. Port 4 is decoupled and without power if ports 2 and 3 are ideally matched. In practice an absorber of suitable power at port 4 is to be planned in accordance with the mismatch of ports 2 and 3. Decoupled combining can be achieved via the diagonally opposite ports 2 and 3 or 1 and 4. 25 20 15 1.0 1.5 2.0 VSWR at port 1 (with 50-� load at port 4) 3-dB Coupler Hybrid Combiner 2:2 1700 – 2200 MHz The 3-dB coupler can be used: – as a decoupled power splitter with a ratio of 1:1, – for the decoupled combining of two transmitters with frequency spacing as narrow as desired (at 3 dB loss), – for the decoupled combining of two receivers with frequency spacing as narrow as desired, – for the decoupled combining of two transmitter/receiver units, whose integrated duplexers are within the same frequency range, – as a frequency-independent 90° phase shifter, – as a component to form combiners. Directivity VSWR Impedance Input power Intermodulation products Temperature range Connectors Application Mounting Weight Packing size Dimensions (w x h x d) 2.5 7-16 female Indoor or outdoor (IP66) With 2 screws (max. 5.5 mm diameter) 1.3 kg 160 x 95 x 65 mm 94 x 59.5 x 89 mm (including connectors) Note: VSWR and attenuation values are measured when the remaining ports are terminated with 50-Ω loads. 1 3 2 4 2200 25 20 15 1.0 1.5 2.0 VSWR at port 1 (with 50-��load at port 4) 313 303 Same-Band / Hybrid Combiners Frequency/MHz Typical attenuation 2 3 vs. VSWR at port 1 1700 – 2200 MHz 3 ±0.4 dB (see diagram I) See diagram II 50 Ω < 300 W total power at two inputs, with max. 200 W at one input < –160 dBc (3 rd order; with 2 x 20 W) –30 ... +70 °C 13 3.5 Diagram II 793006 > 25 dB < 1.15 12 3.0 1700 Attenuation 2 3 / dB Frequency range Attenuation 1 � 2 1 � 3 Attenuation 2 � 3 Typical attenuation between ports 1 2 resp. 1 3 vs. frequency coupler 7-16 Technical Data Type No. Attenuation 1 3 / dB Diagram I earth screw M6 Attenuation 1 2 / dB Function: The 3-dB coupler has four ports, two of which are decoupled from each other. For example effective power entering into port 1 is distributed into ports 2 and 3. Port 4 is decoupled and without power if ports 2 and 3 are ideally matched. In practice an absorber of suitable power at port 4 is to be planned in accordance with the mismatch of ports 2 and 3. Decoupled combining can be achieved via the diagonally opposite ports 2 and 3 or 1 and 4. 3-dB Coupler Hybrid Combiner 2:2 800 – 2200 MHz The 3-dB coupler can be used: – as a decoupled power splitter with a ratio of 1 : 1, – for the decoupled combining of two transmitters with frequency spacing as narrow as desired (at 3 dB loss), – for the decoupled combining of two receivers with frequency spacing as narrow as desired, – for the decoupled combining of two transmitter/receiver units whose integrated duplexers are within the same frequency range, – as a frequency-independent 90° phase shifter, – as a combiner component. Diagram I Directivity VSWR Impedance Input power Intermodulation products Temperatur range Connectors Application Mounting Weight Packing size Dimensions (w x h x d) 4.0 50 Ω < 300 W total power at two inputs, with max. 200 W at one input < –160 dBc (3 rd order; with 2 x 20 W) –30 … +70 °C 7-16 female Indoor or outdoor (IP66) With 2 screws (max. 5.5 mm diameter) 1.3 kg 160 x 95 x 65 mm 104.9 x 50.2 x 93.9 mm (including connectors) 13 Frequency/MHz 1 3 2 4 2200 Diagram II Typical attenuation 2 3 vs. VSWR at port 1 800 – 2200 MHz 3 ±1.2 dB (see diagram I) See diagram II Note: VSWR and attenuation values are measured when the remaining ports are terminated with 50-Ω loads. 314 304 3.0 800 793554 > 20 dB < 1.2 12 2.0 Attenuation 2 3 / dB Frequency range Attenuation 1 � 2 � 3 Attenuation 2 � 3 Typical attenuation between ports 1 2 resp. 1 3 vs. frequency coupler 7-16 Technical Data Type No. Attenuation 1 3 / dB earth screw M6 Attenuation 1 2 / dB Function: The 3-dB coupler has four ports, two of which are decoupled from each other. For example effective power entering into port 1 is distributed into the ports 2 and 3. Port 4 is decoupled and without power if ports 2 and 3 are ideally matched. In practice an absorber of suitable power at port 4 is to be planned for according to the mismatch of ports 2 and 3. Decoupled combining can be achived via the diagonally opposite ports 2 and 3 respectively 1 and 4. VSWR at port 1 (with 50-��load at port 4) System Components Bias Tees Measuring Directional Couplers DC-Stops Attenuators 50-Ω Loads 315 316 Summary of System Components Types System Components: Description Type No. DC Stop DC Stop Bias Tee Bias Tee AISG Bias Tee, outdoor Bias Tee, outdoor (AISG) Smart Bias Tee Smart Bias Tee Smart Bias Tee Smart Bias Tee Smart Bias Tee Smart Bias Tee Smart Bias Tee Smart Bias Tee 50-Ω Load (7-16 female) Low IM 50-Ω Load (N male) 50-Ω Load (7-16 male) 50-Ω Load (7-16 female) 50-Ω Load (N male) 50-Ω Load (N female) 50-Ω Load (N male) 50-Ω Load (N female) 50-Ω Load (N male) 50-Ω Load (7-16 female) 50-Ω Load (7-16 male) 50-Ω Load (N female) 50-Ω Load (N male) 50-Ω Load (7-16 female) 50-Ω Load (7-16 male) 50-Ω Load (N female) 50-Ω Load (N male) 50-Ω Load (7-16 female) Attenuator 3 dB Attenuator 6 dB Attenuator 10 dB Attenuator 20 dB Attenuator 3 dB Attenuator 6 dB Attenuator 10 dB Attenuator 20 dB Measuring Directional Coupler 793301 78210850V01 793304 78210429 78210577 78210578 78211053 78211054 78211055 78211056 78211063 78211064 78211065 78211066 78210474 K6226611 78410367 78410470 K6226111 K6226401 K6226411 K6226201 K6226211 K6226207 K6226217 K6226301 K6226311 K6226307 K6226317 K6226501 K6226511 K6226507 78410235 78410236 78410237 78410238 791918 791919 791920 791921 792972 Frequency range Max. input power Page 800 – 2170 MHz 250 – 2700 MHz 800 – 2170 MHz 800 – 2170 MHz 690 – 2700 MHZ 690 – 2700 MHZ 690 – 2700 MHz 690 – 2700 MHz 690 – 2700 MHz 690 – 2700 MHz 690 – 2700 MHz 690 – 2700 MHz 690 – 2700 MHz 690 – 2700 MHz 800 – 2700 MHz 0 – 2700 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 2700 MHz 0 – 1000 MHz 0 – 1000 MHz 0 – 1000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 0 – 4000 MHz 824 – 960 MHz 960 – 2500 MHz 750 W 750 W 250 W 250 W 250 W 250 W 750 W 750 W 750 W 750 W 750 W 750 W 750 W 750 W 80 W 0.5 W 1.5 W 1.5 W 2W 10 W 10 W 25 W 25 W 25 W 25 W 50 W 50 W 50 W 50 W 100 W 100 W 100 W 2W 2W 2W 2W 15 W 12 W 10 W 10 W 800 W 200 W 318 319 320 321 322 323 324 – 326 324 – 326 324 – 326 324 – 326 324 – 326 324 – 326 324 – 326 324 – 326 327 328 328 328 328 328 328 329 329 329 329 329 329 329 329 329 329 329 330 330 330 330 330 330 330 330 331 New Products 317 DC Stop 800 – 2170 MHz DC Stop is used in dual- or multi-band antenna systems where one or more antenna systems require a DC supply for an installed mast head amplifier. The DC Stop prevents DC voltage from being shorted within the non-biased antenna system(s) and isolates the corresponding base station output(s) from DC voltage. • Low RF signal insertion loss • High DC signal isolation from port 1 to port 2 and vice versa • Suitable for indoor or outdoor applications 70.4 39.5 M29x1.5 793 301 DC - Stop 800–2170 MHz 32 Application Example Technical Data Type No. Frequency range Insertion loss Port 1 � Port 2 Isolation Port 1 � Port 2 VSWR Impedance Input power Intermodulation products Temperature range Connectors Port 1 Port 2 Application Weight Dimensions (w x h x d) 318 308 793 301 Port 2 800 – 2170 MHz < 0.1 dB (800 – 2170 MHz) > 70 dB (DC) < 1.1 ( 800 – 2000 MHz) < 1.2 (2000 – 2170 MHz 50 Ω < 750 W (800 – 2170 MHz) < –160 dBc (3rd order; with 2 x 20 W) –40 ... +70 °C 7-16 male 7-16 female Indoor or outdoor (IP 67) 0.32 kg 70.4 mm x 39.5 mm x 32 mm (including connectors and earthing screw of 6 mm diameter) Port 1 DC Stop 250 - 2700 MHz DC Stop is used in dual- or multi-band antenna systems where one or more antenna systems require a DC supply for an installed mast head amplifier. The DC Stop prevents DC voltage from being shorted within the non-biased antenna system(s) and isolates the corresponding base station output(s) from DC voltage. • Low RF signal insertion loss • High DC signal isolation from port 1 to port 2 and vice versa • Isolation of AISG signals • Suitable for indoor or outdoor applications 70.4 39.5 M29x1.5 78210850 DC - Stop 250–2700 MHz 32 Technical Data Type No. 78210850V01 Frequency range 250 - 2700 MHz Insertion loss Port 1 ↔ Port 2 < 0.1 dB (250 - 2700 MHz) Isolation Port 1 ↔ Port 2 VSWR Impedance Input power Intermodulation products Temperature range DC Stop > 23 dB (AISG 2.176 MHz) < 1.5 (250 - 380 MHz) < 1.25 (380 - 690 MHz) < 1.1 (690 - 2700 MHz) 50 Ω < 750 W (250 - 2700 MHz) < -160 dBc (3rd order; with 2 x 20 W) 7-16 male 7-16 female Application Indoor or outdoor (IP 67) Dimensions (w x h x d) Port 1 -40 ... +70 °C Connectors Port 1 Port 2 Weight Port 2 0.32 kg 70.4 mm x 39.5 mm x 32 mm (including connectors and earthing screw of 6 mm diameter) 319 Bias Tee 800 – 2170 MHz The Bias Tee is suitable to feed DC voltage into the feeder cable of a receiving and/or transmitting antenna system in order to provide the operating voltage for a mast head amplifier. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken to protect against static discharge and lightning ensure a high level of reliability and operational safety. 16 35.4 793 304 Bias Tee 800–2170 MHz Antenna BTS DC DC 6.5 6.5 28.5 47 88 Application Example Technical Data Type No. Frequency range Insertion loss BTS � Antenna Isolation BTS � Antenna BTS � DC VSWR Impedance Input power BTS DC Intermodulation products Lightning protection Temperature range Connectors BTS Antenna Port DC Application Weight Packing size Dimensions (w x h x d) 320 310 793304 Antenna 800 – 2170 MHz < 0.1 dB (800 – 2170 MHz) > 70 dB (DC) > 70 dB (DC) < 1.1 (800 – 2170 MHz) 50 Ω < 250 W (800 – 2170 MHz) < 1000 mA / 0 ... +30 VDC < –160 dBc (3rd order; with 2 x 20 W) 5 kA, 8/20 s pulse –40 ... +70 °C 7-16 male 7-16 female SMB male Indoor 0.6 kg 145 x 145 x 50 mm 88 x 47 x 35.4 mm (including connectors and earthing screw of 6 mm diameter) BTS Port DC Bias Tee 800 – 2170 MHz The Bias Tee is suitable to feed DC voltage and AISG control signals into the feeder cable in order to provide operating voltage and control signals via the RF feeder cable to the TMA or RCU. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage and AISG control signal (2.176 MHz) is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken in conjunction with the CCU-LOC to protect against static discharge and lightning ensure a high level of reliability and operational safety. 16 35.4 793 304 Bias Tee Bias Tee 800–2170 MHz 800–2170 MHz Antenna BTS Antenna BTS DC DC/AISG DC 6.5 6.5 28.5 47 88 Application Example Type No. Frequency range Insertion loss BTS � Antenna Isolation BTS � Antenna BTS � DC/AISG VSWR Impedance Input power BTS DC/AISG Lightning protection Intermodulation products Temperature range Connectors Port 1 BTS Port 2 Antenna Port DC/AISG Application Weight Packing size Dimensions (w x h x d) 78210429 800 – 2170 MHz Port 2 Feeder < 0.1 dB (800 – 2170 MHz) > 70 dB (DC) > 70 dB (DC) < 1.1 (800 – 2170 MHz) 50 Ω Port 1 BTS Port DC/AISG < 250 W (800 – 2170 MHz) < 1.8 A / 13 VDC < 0.8 A / 29 VDC 3 kA, 10/350 s pulse < –160 dBc (3rd order; with 2 x 20 W) –40 ... +70 °C 7-16 male 7-16 female SMB male Indoor 0.6 kg 145 x 145 x 50 mm 88 x 47 x 35.4 mm (including connectors and earthing screw of 6 mm diameter) 321 311 System Components Technical Data Bias Tee 690 – 2700 MHz The Bias Tee is suitable to feed DC voltage into the feeder ca-ble of a receiving and/or transmitting antenna system in order to provide the operating voltage for a mast head amplifier. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken to protect against static discharge and lightning ensure a high level of reliability and operational safety. Application Example Technical Data Type No. Frequency range Insertion loss Port 1 � Port 2 Isolation Port 1 � Port 2 Port 1 � DC VSWR Impedance Input power Port 1 DC Intermodulation products Lightning protection Temperature range Connectors Port 1 (BTS) Port 2 (Antenna) Port DC Application Weight Packing size Dimensions (w x h x d) 322 312 Port DC Port 2 Antenna 78210577 690 – 2700 MHz < 0.1 dB (690 – 2700 MHz) > 70 dB (DC) > 70 dB (DC) < 1.1 (690 – 2700 MHz) 50 Ω < 250 W (690 – 2700 MHz) < 1 A / 0 ... +30 VDC < –160 dBc (3rd order; with 2 x 20 W) 3 kA, 10/350 s pulse –40 ... +70 °C 7-16 male 7-16 female SMA female Indoor or outdoor (IP 66) 0.47 kg 128 x 75 x 88 mm 85.4 x 45 x 46.2 mm (including connectors and earthing screw of 6 mm diameter) Port 1 BTS Bias Tee (AISG) 690 – 2700 MHz The Bias Tee is suitable to feed DC voltage and AISG control signals into the feeder cable in order to provide operating voltage and control signals via the RF feeder cable to the TMA or RCU. • The Bias Tee provides low RF signal insertion loss from the BTS to the antenna port and vice versa. • The DC voltage and AISG control signal (2.176 MHz) is fed from the DC port to the antenna port while providing a high level of DC isolation from the DC to the BTS port and from the antenna to the BTS port. • The measures taken in conjunction with the CCU-LOC to protect against static discharge and lightning ensure a high level of reliability and operational safety. Application Example Technical Data Frequency range Insertion loss Port 1 � Port 2 Isolation Port 1 � Port 2 Port 1 � Port DC/AISG VSWR Impedance Input power Port 1 Port DC/AISG Intermodulation products Lightning protection Temperature range Connectors Port 1 (BTS) Port 2 (Antenna) Port DC/AISG Application Weight Packing size Dimensions (w x h x d) 78210578 Port DC/AISG 690 – 2700 MHz Port 2 Antenna < 0.1 dB (690 – 2700 MHz) > 70 dB (DC) > 70 dB (DC) < 1.1 (690 – 2700 MHz) 50 Ω < 250 W (690 – 2700 MHz) < 1 A / 0 ... +30 VDC < –160 dBc (3rd order; with 2 x 20 W) 3 kA, 10/350 s pulse –40 ... +70 °C Port 1 BTS 7-16 male 7-16 female SMA female Indoor or outdoor (IP 66) 0.47 kg 128 x 75 x 88 mm 85.4 x 45 x 46.2 mm (including connectors and earthing screw of 6 mm diameter) 323 313 System Components Type No. Smart Bias Tee 690 – 2700 MHz The Smart Bias Tee combines the performance of a standard Bias Tee (e.g. type 78210577) with the function of an additional modem (AISG standard) in order to provide either DC voltage as well as remote control signals via an RF feeder cable to a TMA or RCU. The Smart Bias Tee provides low RF signal insertion loss from port 1 to port 2 and vice versa.The measures taken to protect against static discharge and lightning ensure a high level of reliability and operational safety. 78211053, 78211063: +8 ... 14 VDC (DC on pin1) version for use near the BTS, in order to feed-in DC voltage and RCU control signals into a feeder cable (only required for TMAs and RCUs with power supply below 15 VDC) 78211054, 78211064: +8 ... 14 VDC (DC on pin1) version for use near the antenna, in order to control an RCU (only required if no TMA is in use) 78211055, 78211065: +8 ... 32 VDC (DC on pin6) version for use near the BTS, in order to feed-in DC voltage and RCU control signals into a feeder cable 78211054 78211056 Port 1 Antenna Port 2 Feeder 78211064 78211066 Port 2 Feeder Port 1 Antenna 78211056, 78211066: +8 ... 32 VDC (DC on pin6) version for use near the antenna, in order to control an RCU (only required if no TMA is in use) 78211053 78211055 Port 1 BTS Port 2 Feeder Abbreviations: RCU = Remote Control Unit for remote electrical control of antenna tilt BTS = Base Transceiver Station TMA = Tower Mounted APSOL¿HU AISG = Antenna Interface Standards Group Port 1 = Port for BTS or for Antenna Port 2 = Port for Feeder Cable Port DC/RCU = Port for DC voltage and Remote Control Unit signals 78211063 78211065 Port 1 BTS Port 2 Feeder 936.3819h Subject to alteration. Pin connections: www.kathrein.de 78211053, 78211054 ... Page 1 of 4 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 324 Smart Bias Tee 690 – 2700 MHz Technical Data Type No. Port 1: 7-16 male Port 2: 7-16 female Type No. Port 1: 7-16 female Port 2: 7-16 male 78211053 78211054 78211055 78211056 +8 ... +14 VDC / BTS +8 ... +14 VDC / Antenna +8 ... +32 VDC / BTS +8 ... +32 VDC / Antenna BTS Antenna BTS Antenna Feeder Feeder Feeder Feeder 78211063 78211064 78211065 78211066 +8 ... +14 VDC / BTS +8 ... +14 VDC / Antenna +8 ... +32 VDC / BTS +8 ... +32 VDC / Antenna BTS Antenna BTS Antenna Feeder Feeder Feeder Feeder Frequency range 690 - 2700 MHz Insertion loss 3RUWļ3RUW < 0.1 dB (690 - 2700 MHz) Isolation for DC and RCU signals 3RUWļ3RUW 3RUWļ3RUW'&5&8 3RUWļ3RUW'&5&8 > 70 dB > 70 dB > 0 dB VSWR < 1.1 (690 - 2700 MHz) ȍ Impedance Input power Port 1 or Port 2 Port DC/RCU Power consumption Lightning protection Intermodulation products Temperature range Modem carrier frequency Application < 750 W (690 - 2700 MHz) < 2.5 A / +8 ... +14 VDC < 750 W (690 - 2700 MHz) < 2.5 A / +8 ... +32 VDC Typically 0.6 W N$ȝVSXOVH < – 160 dBc (3rd order; with 2 x 20 W) -40 ... +60 °C 2.176 MHz Indoor or outdoor (IP 66) 167 x 102 x 86 mm Dimensions (w x h x d) 81 x 81 x 46 mm (without connectors) Dimensional drawings: 78211053, 78211055 78211063, 78211065 78211054, 78211056 78211064, 78211066 Page 2 of 4 78211053, 78211054 ... www.kathrein.de KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 325 Subject to alteration. 0.8 kg Packing size (w x h x d) 936.3819h Weight Smart Bias Tee 690 – 2700 MHz Block diagrams: Application Examples: Port 1 (Antenna) 78211054 or 78211056 Port 2 (Feeder) Port DC/RCU (RCU) Port 2 (Feeder) Port DC/RCU (CCU) 78211053 or 78211055 78211053 or 78211055 Port 1 (BTS) Port 1 (Antenna) Port DC/RCU (RCU) Subject to alteration. 78211064 or 78211066 Port 2 (Feeder) Port 2 (Feeder) 936.3819h 78211063 or 78211065 Port 1 (BTS) www.kathrein.de 78211063 or 78211065 Port DC/RCU (CCU) 78211053, 78211054 ... Page 3 of 4 KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494 326 50-Ohm Load 698 – 2700 MHz 80 W • Designed as 50-Ohm termination wherever improved intermodulation performance compared to standard loads is required • Excellent intermodulation performance • Suitable for indoor or outdoor applications • Wall or mast mounting • Built-in DC stop RF Port Technical Data 78210474 Type No. Frequency range VSWR Impedance Input power Intermodulation products Temperature range Connector Application DC/AISG transparency Mounting Weight Packing size Dimensions (w x h x d) 698 – 2700 MHz < 1.12 50 Ω < 80 W (see table) < –160 dBc (3rd order; with 2 x 20 W) –40 … +55 °C 7-16 female (long neck) Indoor or outdoor (IP 66) Built-in DC stop AISG: Attenuation up to 3 dB when used in a network Wall mounting: With 4 screws (max. 6.5 mm diameter) Mast mounting: With additional clamp set (see data sheet) 3.1 kg 377 x 232 x 189 mm 143.6 x 216 x 79.2 mm (including connector) Note: The RF port connector should always point downwards if mounted outdoors. The input power rating of 80 W is specified at an ambient temperature of +40 °C with the combiner mounted vertically, without additional cooling, and while respecting the safety standard EN IEC 60950 (max. surface temperature +90 °C). The max. power rating increases or decreases with falling or rising ambient temperature and depending on horizontal or vertical mounting in accordance with the following table: Max. input power Max. ambient temperature +55 °C +40 °C +25 °C 320 Mounted horizontally Mounted vertically 50 W 70 W 90 W 60 W 80 W 100 W 327 50-Ohm Load 0 ... 4000 MHz 0.5 ... 100 W • Standard 50-Ohm terminations for small and medium power • Suitable for terminating open ports on RF equipment for indoor and/or outdoor applications 0.5 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz 1000 – 2000 MHz 2000 – 2700 MHz Application Weight Packing size Dimensions K6226611 N male 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor 40 g 90 x 60 x 25 mm 33 / 21 mm diameter K 62 26 61 1 1.5 Watt * Type No. Connector Frequency range VSWR 0 – 2000 MHz 2000 – 4000 MHz Application Weight Packing size Dimensions 78410367 7-16 male 78410470 7-16 female 0 – 4000 MHz < 1.10 < 1.30 Indoor or outdoor (IP65) 120 g Approx. 50 x 90 x 100 mm 40 / 32 mm diameter 42 / 29 mm diameter 784 10367 2 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz 1000 – 2000 MHz 2000 – 2700 MHz Application Weight Packing size Dimensions K6226111 N male 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor 40 g 90 x 60 x 25 mm 30 / 21 mm diameter K 62 26 11 1 10 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz 1000 – 2000 MHz 2000 – 2700 MHz Application Weight Packing size Dimensions (w x h x d) 328 318 K6226401 N female K6226411 N male 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor Approx. 250 g 50 x 90 x 100 mm 40 x 82 x 77 mm 40 x 82 x 85 mm (including connector) (including connector) K 62 26 40 1 50-Ohm Load 0 ... 4000 MHz 0.5 ... 100 W 25 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz 1000 – 2000 MHz 2000 – 2700 MHz Application Weight Packing size Dimensions (w x h x d) K6226201 K6226211 N female N male 35 x 94 x 113 mm (incl. connector) K6226207 K6226217 7-16 female 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor Approx. 0.5 kg 50 x 100 x 135 mm 35 x 94 x 121 mm 35 x 94 x 125 mm (incl. connector) (incl. connector) 7-16 male 35 x 94 x 124 mm (incl. connector) K 62 26 20 1 50 Watt * Type No. Connector Frequency range VSWR 0 – 1000 MHz 1000 – 2000 MHz 2000 – 2700 MHz Application Weight Packing size Dimensions (w x h x d) K6226301 K6226311 N female N male 67 x 90 x 130 mm (incl. connector) K6226307 K6226317 7-16 female 0 – 2700 MHz < 1.08 < 1.15 < 1.20 Indoor Approx. 0.8 kg 80 x 95 x 145 mm 67 x 90 x 138 mm 67 x 90 x 134 mm (incl. connector) (incl. connector) 7-16 male 67 x 90 x 133 mm (incl. connector) K 62 26 30 1 Type No. Connector Frequency range VSWR 0 – 1000 MHz Application Weight Packing size Dimensions (w x h x d) K6226501 K6226511 K6226507 N female N male 0 – 1000 MHz < 1.08 Indoor Approx. 2.4 kg 130 x 195 x 180 mm 114 x 161 x 156 mm (including connector) 7-16 female 114 x 153 x 156 mm (including connector) 114 x 170 x 156 mm (including connector) System Components 100 Watt * K 62 26 50 1 * Rated power at 40 °C ambient temperature. The max. power rating increases or decreases with falling or rising ambient temperature. Note: The 50-Ohm load, type 782 010474, should be used if intermodulation requirements are of high priority. 329 319 Attenuator 2 – 15 W 0 – 4000 MHz Air-cooled attenuator for low power rating • Signal attenuation for test, measuring or tuning purposes • Good matching over large frequency range • Closed metal housing, very stable and RF proof • Free choice of mounting position due to convection-cooling Technical Data Type No. Attenuation Frequency range VSWR 78410235 3 ±0.3 dB Impedance Max. power Connectors 78410236 78410237 6 ±0.3 dB 10 ±0.3 dB 0 – 4000 MHz < 1.12 78410238 20 ±0.5 dB 50 Ω 2W N IP65 Outdoor 60 g 49 x 21 mm IP rating Application Weight Dimensions (L x diameter) Air-cooled attenuator for medium power rating System Components • Signal attenuation for test, measuring or tuning purposes • Good matching over large frequency range • Closed metal housing, very stable and RF proof • Free choice of mounting position due to convection-cooling Technical Data Type No. 791918 Attenuation Max. power Frequency range VSWR 3 ±0.3 dB 15 W Impedance Connectors IP rating Application Weight Dimensions (L x diameter) 330 791919 791920 791921 6 ±0.3 dB 10 ±0.3 dB 12 W 10 W 0 – 4000 MHz < 1.15 20 ±0.5 dB 10 W 50 Ω N IP65 Outdoor 70 g 50 x 26 mm 321 Measuring Directional Coupler 824 – 2500 MHz The Measuring Directional Coupler provides measurement ports for monitoring the forward and reflected power of a RF signal. • Easy implementation into existing RF systems due to male/female connectors • Input and output ports are reciprocal in nature • Front panel mounting possible via flange • Suitable for indoor applications Forward Port Output Port Input Port Reflected Port 102.8 Technical Data Type No. Frequency range Insertion loss Input port � Output port Coupling attenuation Input port � Forward port Output port � Reflected port Directivity VSWR Input port, Output port Forward port, Reflected port 792972 824 – 2500 MHz < 0.05 dB (824 – 2500 MHz) 32.0 ±0.75 dB (824 – 960 MHz) 28.5 ±1.50 dB (1710 – 2500 MHz) 32.0 ±0.75 dB (824 – 960 MHz) 28.5 ±1.50 dB (1710 – 2500 MHz) > 28 dB (824 – 2200 MHz) > 25 dB (2200 – 2500 MHz) < 1.04 (824 – 960 MHz) < 1.08 (960 – 2500 MHz) < 1.2 (824 – 2500 MHz) Impedance 50 Ω Input power < 800 W (824 – 960 MHz) < 200 W (960 – 2500 MHz) < –160 dBc (3rd order; with 2 x 20 W) –20 … +55 °C Intermodulation products Temperature range Connectors Input port Output port Forward port, Reflected port Application Mounting Weight Dimensions (w x h x d) 322 7-16 male 7-16 female MCX female Indoor Front panel mounting possible with 4 screws (max. 2.5 mm diameter) 0.26 kg 32 x 32 x 102.3 mm 331 332 DTMAs 333 Summary of DTMA Types DTMAs: Description Type No. DTMA-800-12-AISG DTMA-850-12-AISG-CWA DTMA-800-900-12-AISG-CWA 78210430 78210874 78210510 DTMA-800-900-12-AISG-CWA 78210511 DTMA-900-12-32-AISG-CWA 78210440 UL: 832 – 862 / DL: 791 – 821 MHz UL: 824 – 849 / DL: 869 – 894 MHz UL: 832 – 862 / DL: 791 – 821 MHz UL: 880 – 915 / DL: 925 – 960 MHz UL: 832 – 862 / DL: 791 – 821 MHz UL: 880 – 915 / DL: 925 – 960 MHz UL: 880 – 915 / DL: 925 – 960 MHz DTMA-900-12-32-AISG-CWA 78210442 UL: 880 – 915 / DL: 925 – 960 MHz DTMA-900-32-AISG-CWA DTMA-900-12-AISG-CWA DTMA-1800-12-CWA DTMA-1800-12-AISG DTMA-1800-12-AISG-CWA DTMA-1800-UMTS-12-AISG-CWA DTMA-1800-UMTS-12-AISG-CWA 78210490 78210495 78210580 78210581 78210583 78211103 78211105 DTMA-1800-UMTS-12-AISG DTMA-1800-UMTS-12-AISG-D 78211106 78210990 DTMA-AWS-12-AISG-CWA DTMA-1900-12-AISG-CWA DTMA-UMTS-12-AISG-CWA DTMA-UMTS-12-AISG-CWA DTMA-UMTS-12-AISG-CWA DTMA-UMTS-24-AISG-CWA DTMA-UMTS-12-AISG DTMA-UMTS-12-AISG-CWA DTMA-UMTS-BYP1800-12-AISG-CWA 78210877 78210876 78210610 78210612 78211120 78210613 78211145 78211245 78211102 DTMA-UMTS-BYP1800-12-AISG-CWA 78211104 DTMA-2600-12-AISG 78210860 UL: 880 – 915 / DL: 925 – 960 MHz UL: 880 – 915 / DL: 925 – 960 MHz UL: 1710 – 1785 / DL: 1805 – 1880 MHz UL: 1710 – 1785 / DL: 1805 – 1880 MHz UL: 1710 – 1785 / DL: 1805 – 1880 MHz UL: 1710 – 1785 / DL: 1805 – 1880 MHz UL: 1710 – 1785 / DL: 1805 – 1880 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz UL: 1710 – 1785 / DL: 1805 – 1880 MHz UL: 1710 – 1785 / DL: 1805 – 1880 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz UL: 1710 – 1770 / DL: 2110 – 2170 MHz UL: 1850 – 1910 / DL: 1930 – 1990 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz UL: 1920 – 1980 / DL: 2110 – 2170 MHz Bypass: 1710 – 1880 UL: 1920 – 1980 / DL: 2110 – 2170 MHz Bypass: 1710 – 1880 UL: 2500 – 2570 / DL: 2620 – 2690 MHz New Products 334 Frequency range UL = Up Link / DL = Down Link Gain Page 12 dB 12 dB 12 dB 336 337 338, 339 12 dB 338, 339 12/32 dB 12/32 dB 32 dB 12 dB 12 dB 12 dB 12 dB 12 dB 12 dB 340 341 342 343 344 345 346, 347 346, 347 12 dB 12 dB 348 349, 350 12 dB 12 dB 12 dB 12 dB 12 dB 24 dB 12 dB 12 dB 12 dB 351 352 353 353 353 354, 355 356 357 358, 359 12 dB 358, 359 12 dB 360 340 antenna outputs Gain ● ● ● ● ● ● ● ● ● 78210580 78210581 78210583 78211103 78211105 78211106 AISG* Low CWA 12dB 24dB ● ● 78210490 ●¹ ●¹ ● = default; * = AISG2.0 (default) & AISG1.1 (optional); Low CWA (Current Window Alarm) = 170 - 200mA; High CWA (Current Window Alarm) = 230 - 295mA; ¹ = Current Window Alarm 800 - 900mA ● ● 78210442 ● ● ● ● 78211104 78210860 ● ● ● ● 78211102 78210440 ● ● 78211245 ● ● ● ● ● ● ● ● ● ● ● ● AISG* ● ● ● 78211145 2100 2600 ● Low CWA 78210613 ● ● ● ● ● ● ● ● ● ● ● 78210612 ● High CWA 78211120 ● AISG* ● ● Low CWA ● ● ● ● High CWA 78210876 ●¹ Low CWA ● High CWA ● AISG* 78210877 ● AWS Low CWA ● ● ● 78210495 1900 High CWA 78210990 ● ● ● 78210442 ● ● ● ● ● ● ● ● ● ● ● ● ● 1800 78210440 2 outputs 78210874 4 outputs ● AISG* ● Low CWA ● High CWA ● AISG* 78210511 Low CWA 78210510 High CWA ● 900 High CWA ● Low CWA ● 850 RF-Bypass ● AISG* ● 800 AISG* 78210430 Frequency/MHz Choose your DTMA High CWA 32dB 335 DTMA-800-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Compact line • Double unit for easy use with XPol antennas • Supports AISG 1.1 and 2.0 (default) • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down Ant 0 • Built-in lightning protection AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt Ant 1 Technical Data Type No. 78210430 DTMA-800-12-AISG (12 dB gain) Tx Characteristics Frequency range Insertion loss Ripple Input power (per input) Intermodulation products in RX band Return loss 791 - 821 MHz Typically 0.25 dB Node B0 AISG and DC-Port < 0.3 dB < 100 W (+50 dBm) CW < -117 dBm (2 Tx carriers at +43 dBm) RET > 18 dB Rx Characteristics Frequency range 832 - 862 MHz Loss in by-pass mode Typically 2.0 dB Return loss Gain > 16 dB (DC ON) 12 dB nominal Noise figure Typically 1.2 dB 3 order intercept point (OIP3) Typically 30 dBm rd Environmental Characteristics Operating temperature range IP rating -40 ... +65 °C IP67* MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current per DTMA (without RET) Alarm management 10 - 30 V Nom. 155 mA at 10 V Nom. 60 mA at 30 V AISG Mechanical Characteristics Material Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) * see note on data sheet 336 Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 30 V DC, pin 7: DC return, other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 6.2 kg 250 x 450 x 210 mm 176 x 246.6 x 103.6 mm (without connectors, without mounting brackets) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Node B 1 DTMA-850-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • Supports CWA, AISG 1.1 and AISG 2.0 (default) • AISG setting swichable • CWA and AISG configuration • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt CWA = Current Window Alarm Ant 0 Ant 1 • Built-in lightning protection Technical Data 78210874 Type No. Node B 0 DTMA-850-12-AISG-CWA (12 dB gain) RET Node B 1 Tx Characteristics Frequency range 869 - 894 MHz Insertion loss Typically 0.35 dB Input power (per input) Intermodulation products in RX band < 100 W (+50 dBm) < -117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 824 - 849 MHz Loss in bypass mode Return loss Typically 1.5 dB (DC OFF) > 18 dB (DC ON) / > 15 dB (DC OFF) 12 dB nominal Gain Noise figure Typically 1.6 dB Output 1-dB compression point > 10 dBm 3rd order intercept point (OIP3) Typically 25 dBm Environmental Characteristics Operating temperature range -40 ... +65 °C IP rating IP67* MTBF > 1 200 000 hours (per TMA) EMC FCC Part 15 DC and Alarm Characteristics DC supply CWA Mode AISG Mode 9 - 19 V 9 - 30 V Operating current per TMA 80 - 130 mA Nom. 50 mA at 12 V Alarm management 170 - 180 mA AISG* Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm Aluminium housing 734361 60 - 80 mm 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 6: 9 - 30 V DC, pin 3: RS485B, pin 5: RS485A, pin 7: DC return, other pins: Not connected) 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Mechanical Characteristics Material Accessories (order separately) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 4.9 kg 400 x 250 x 150 mm 168 x 275 x 73 mm (without connectors, without mounting brackets) * see note on data sheet 337 DTMA-800-900-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • • • • • • • Double unit for easy use with XPol antennas Suitable for antenna RET control according to AISG/3GPP standard Bypass mode to ensure cell operation in case of DC power down Supports CWA, AISG 1.1 and AISG 2.0 (default) Built-in lightning protection AISG setting switchable CWA and AISG configurations AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt CWA = Current Window Alarm Ant 1 Ant 0 Technical Data Type No. 78210510 CWA alarm 170 - 200 mA 78210511 DTMA-800-900-12-AISG-CWA 230 - 295 mA 800 MHz Tx Characteristics Frequency range 791 - 821 MHz Insertion loss Typically 0.5 dB Input power (per input) Intermodulation products in RX band Return loss < 100 W (+50 dBm) / < 1.6 kW (+62 dBm) peak < -116 dBm (2 Tx carriers at +43 dBm) > 18 dB 800 MHz Rx Characteristics Frequency range 832 - 862 MHz Loss in bypass mode Typically 2.0 dB Return loss Gain > 18 dB (DC ON) / > 14 dB (DC OFF) 12 dB nominal Noise figure Typically 1.5 dB 3 order intercept point (OIP3) Typically 25 dBm rd 900 MHz Tx Characteristics Frequency range Insertion loss Input power (per input) Intermodulation products in RX band Return loss 925 - 960 MHz Typically 0.5 dB < 100 W (+50 dBm) / < 1.6 kW (+62 dBm) peak < -116 dBm (2 Tx carriers at +43 dBm) > 18 dB 900 MHz Rx Characteristics Frequency range 880 - 915 MHz Loss in bypass mode Typically 2.0 dB Return loss Gain > 18 dB (DC ON) / > 14 dB (DC OFF) 12 dB nominal Noise figure Typically 1.5 dB 3rd order intercept point (OIP3) Typically 25 dBm Environmental Characteristics Operating temperature range IP rating * see note on data sheet 338 -40 ... +65 °C IP67* Node B 0 Node B 1 DTMA-800-900-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 Lightning protection 3 kA, 10/350 µs pulse DC and Alarm Characteristics CWA Mode AISG Mode DC supply 9 - 19 V DC 9 - 31 V DC Operating current per DTMA (without RET) 80 - 120 mA Nom. 300 mA at 10 V Nom. 100 mA at 30 V 78210510: 170 - 200 mA 78210511: 230 - 295 mA AISG Alarm management Mechanical Characteristics Material Connectors Aluminium housing RF AISG Mounting Weight Dimensions (w x h x d) 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 - 31 V DC, pin 7: DC return, other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 11 kg Approx. 210 x 240 x 140 mm (without connectors, without mounting brackets) 339 DTMA-900-12-32-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • • • • • • • • Double units for easy use with XPol antennas Gain setting switchable from 12 dB (default) to 32 dB Both versions support CWA, AISG 1.1 and AISG 2.0 (default) 782 10440: CWA alarm 170 – 200 mA / 800 – 900 mA 782 10442: CWA alarm 230 – 295 mA / 800 – 900 mA AISG and gain setting switchable as described on page 2 CWA and AISG configurations as described on page 2 Suitable for antenna RET control according to AISG/3GPP standard By-pass mode to ensure cell operation in case of DC power down Built-in lightning protection RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Technical Data Type No. 78210440 CWA alarm 170 – 200 mA / 800 – 900 mA DTMA-900-12-32-AISG-CWA (12/32 dB gain) CWA alarm 230 – 295 mA / 800 – 900 mA DTMA-900-12-32-AISG-CWA (12/32 dB gain) 78210442 Tx Characteristics Frequency range 925 – 960 MHz Insertion loss* Typically 0.5 dB Input power (per input) < 180 W (+52.5 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range Loss in by-pass mode Return loss Gain Noise figure Input 3rd order intercept point (IIP3) 880 – 915 MHz Typically 4 dB (DC OFF) > 16 dB (DC ON) 12/32 dB nominal Typically 1.3 dB Typically 5 dBm Environmental Characteristics Operating temperature range IP rating MTBF EMC –40 … +55 °C IP 67* > 1 000 000 hours (per TMA) According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current per TMA (without RET) Alarm management 12 dB gain 32 dB gain Mechanical Characteristics Material Connectors RF AISG Weight Packing size Mounting Dimensions (w x h x d) * see note on data sheet 340 334 CWA Mode 8.5 – 19 V (12 dB gain) 8.5 – 15 V (32 dB gain) 80 – 130 mA (12 dB gain) 360 – 400 mA (32 dB gain) 782 10440: 170 – 200 mA 782 10442: 230 – 295 mA 800 – 900 mA AISG Mode 10 – 30 V < 110 mA (12 dB gain) < 350 mA (32 dB gain) AISG* Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 – 30 V DC, pin 7: DC return, other pins: not connected) 8.7 kg 342 x 579 x 212 mm Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 250 x 353 x 94 mm (without connectors, without mounting brackets) Accessories (order separately) Type No. 734360 734361 734362 734363 734364 734365 Clamp set suitable for mast diameter of 34 60 80 100 120 45 – – – – – – 60 80 100 120 140 125 mm mm mm mm mm mm DTMA-900-32-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Compact line • Double unit for easy use with XPol antennas • Supports CWA, AISG 1.1 and AISG 2.0 (default) • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down Ant 1 Ant 0 • Built-in lightning protection • AISG setting swichable AISG = Antenna Interface Standards Group • CWA and AISG configuration RET = Remote Electrical Tilt CWA = Current Window Alarm Technical Data 78210490 Type No. DTMA-900-32-AISG-CWA Tx Characteristics Frequency range 925 - 960 MHz Insertion loss < 0.8 dB Input power (per input) Intermodulation products in RX band Node B 0 < -115 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB RET Block Diagram Rx Characteristics Frequency range Node B 1 < 100 W (+50 dBm) / < 1.6 kW (+62 dBm) peak 880 - 915 MHz Loss in bypass mode Return loss < 4.0 dB > 16 dB (DC ON) / > 12 dB (DC OFF) Gain 32 dB ±1 dB Noise figure ≤ 2.2 dB Input 1-dB compression point > -7 dBm 3rd order intercept point (OIP3) < 37 dBm Environmental Characteristics Operating temperature range -40 ... +55 °C IP rating IP67* MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics CWA Mode AISG Mode DC supply 7 - 15 V DC 10 - 32 V DC Operating current per DTMA (without RET) 300 - 410 mA Nom. 400 mA at 10 V Nom. 150 mA at 30 V Alarm management 800 - 900 mA AISG* Mechanical Characteristics Material Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm Aluminium housing 734361 60 - 80 mm 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 - 30 V DC, pin 7: DC return, other pins: Not connected) 734362 80 - 100 mm 734363 100 - 120 mm Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 734364 120 - 140 mm 734365 45 - 125 mm 6.2 kg 270 x 495 x 190 mm 185 x 265 x 105 mm (without connectors, without mounting brackets) * see note on data sheet 341 DTMA-900-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Compact line • Double unit for easy use with XPol antennas • Supports CWA, AISG 1.1 and AISG 2.0 (default) • Suitable for antenna RET control according to AISG/3GPP standard • Built-in lightning protection • AISG setting swichable • CWA and AISG configuration Ant 1 Ant 0 • By-pass mode to ensure cell operation in case of DC power down AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt CWA = Current Window Alarm Technical Data 78210495 Type No. DTMA-900-12-AISG-CWA Tx Characteristics Frequency range 925 - 960 MHz Insertion loss Typ. 0.5 dB Input power (per input) Intermodulation products in RX band Node B 1 < 100 W (+50 dBm) / < 1.6 kW (+62 dBm) peak Node B 0 < -115 dBm (2 Tx carriers at +43 dBm) Return loss RET > 18 dB Rx Characteristics Frequency range 880 - 915 MHz Loss in bypass mode Return loss Typ. 1.8 dB > 16 dB (DC ON) / > 12 dB (DC OFF) Gain 12 dB nominal Noise figure Typ. 1.5 dB Output 1-dB compression point 3 order intercept point (OIP3) rd > 15 dBm Typically 30 dBm Environmental Characteristics Operating temperature range -40 ... +55 °C IP rating IP67* MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics CWA Mode AISG Mode DC supply 7 - 19 V DC 10 - 30 V DC Operating current per DTMA (without RET) 80 - 120 mA Nom. 155 mA at 10 V Nom. 63 mA at 30 V Alarm management 170 - 200 mA AISG* Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) * see note on data sheet 342 Node B1 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm Aluminium housing 734361 60 - 80 mm 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 - 30 V DC, pin 7: DC return, other pins: Not connected) 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 734365 45 - 125 mm Mechanical Characteristics Material Node B0 6.2 kg 270 x 495 x 190 mm 185 x 265 x 105 mm (without connectors, without mounting brackets) DTMA-1800-12-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Compact line • Double units for easy use with XPol antennas • Alarm management: CWA • Bypass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 0 Ant 1 CWA = Current Window Alarm Ant 0 Ant 1 BTS 0 BTS 1 DTMA BTS 0 BTS 1 Technical Data Type No. Tx Characteristics Frequency range Insertion loss Input power (per input) Intermodulation products in Rx band Return loss 78210580 DTMA-1800-12-CWA (12 dB gain) 1805 – 1880 MHz Typically 0.25 dB < 200 W (+53 dBm) CW / < 1.6 kW (+62 dBm) peak < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB Rx Characteristics Frequency range Loss in bypass mode Return loss Gain Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) 1710 – 1785 MHz Typically 1.7 dB (DC OFF) > 16 dB (DC ON) 12 dB nominal Typically 1.0 dB > 10 dBm Typically 30 dBm Environmental Characteristics Operating temperature range IP rating MTBF EMC –40 … +65 °C IP67* > 1 000 000 hours (per TMA) According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current per DTMA (without RET) Alarm management Mechanical Characteristics Material Connectors Mounting Weight Packing size Dimensions (w x h x d) * see note on data sheet 326 CWA Mode 7 – 15 V Typically 80 mA 230 – 290 mA Aluminium housing 7-16 female (long neck) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 4 kg 235 405 x 405 235 x 175 mm 218 x 169 x 74.3 mm (without connectors, without mounting brackets) Accessories (order separately) Type No. 734 360 734 361 734 362 734 363 734 364 734 365 Clamp set suitable for mast diameter of 34 – 60 mm 60 – 80 mm 80 – 100 mm 100 – 120 mm 120 – 140 mm 45 – 125 mm 343 DTMA-1800-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Compact line • Double units for easy use with XPol antennas • Supports AISG 1.1 and AISG 2.0 (default) • Suitable for antenna RET control according to AISG/3GPP standard • Bypass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 1 Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group Ant 0 Ant 1 BTS 0 AISG port DTMA BTS 0 BTS 1 BTS 1 RET Technical Data Tx Characteristics Frequency range Insertion loss Input power (per input) Intermodulation products in Rx band Return loss 78210581 DTMA-1800-12-AISG (12 dB gain) 1805 – 1880 MHz Typically 0.25 dB < 200 W (+53 dBm) CW / < 1.6 kW (+62 dBm) peak < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB Rx Characteristics Frequency range Loss in bypass mode Return loss Gain Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) 1710 – 1785 MHz Typically 1.7 dB (DC OFF) > 16 dB (DC ON) 12 dB nominal Typically 1.0 dB > 10 dBm Typically 30 dBm Environmental Characteristics Operating temperature range IP rating MTBF EMC –40 … +65 °C IP67* > 1 000 000 hours (per TMA) According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current per DTMA (without RET) Alarm management AISG Mode 10 – 30 V Nom. 130 mA at 10 V Nom. 50 mA at 30 V AISG Mechanical Characteristics Material Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) * see note on data sheet 344 Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 – 30 V DC, pin 7: DC return, other pins: not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 4 kg 235 x 405 x 175 mm 169 x 218 x 74.3 mm (without connectors, without mounting brackets) Accessories (order separately) Type No. 734 360 734 361 734 362 734 363 734 364 734 365 Clamp set suitable for mast diameter of 34 – 60 mm 60 – 80 mm 80 – 100 mm 100 – 120 mm 120 – 140 mm 45 – 125 mm DTMAs Type No. 327 DTMA-1800-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double units for easy use with XPol antennas • Supports CWA, AISG 1.1 and AISG 2.0 (default) • AISG setting switchable • CWA and AISG configurations • Suitable for antenna RET control according to AISG/3GPP standard • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 1 Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group Ant 0 Ant 1 DTMA BTS 0 BTS 0 AISG port BTS 1 BTS 1 RET Technical Data Type No. 936. Subject to alteration. Tx Characteristics Frequency range Insertion loss Input power (per input) Intermodulation products in Rx band Return loss 78210583 DTMA-1800-12-AISG-CWA (12 dB gain) 1805 – 1880 MHz Typically 0.25 dB < 200 W (+53 dBm) CW / < 1.6 kW (+62 dBm) peak < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB Rx Characteristics Frequency range Loss in by-pass mode Return loss Gain Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) 1710 – 1785 MHz Typically 1.7 dB (DC OFF) > 16 dB (DC ON) 12 dB nominal Typically 1.0 dB > 10 dBm Typically 30 dBm Environmental Characteristics Operating temperature range IP rating MTBF EMC –40 … +65 °C IP67* > 1 000 000 hours (per TMA) According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current per DTMA (without RET) Alarm management Mechanical Characteristics Material Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) seenote noteon ondata page 2 ** see sheet www.kathrein.de CWA 7 – 19 V 80 – 120 mA 170 – 200 mA Node B0 Node B1 AISG Mode 10 – 30 V Nom. 1 mA at 10 V Nom. mA at 30 V AISG* Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 4 kg 405 x 235 x 175 mm 218 x 169 x 74.3 mm (without connectors, without mounting brackets) Accessories (order separately) Type No. 734360 734361 734362 734363 734364 734365 Clamp set suitable for mast diameter of 34 – 60 mm 60 – 80 mm 80 – 100 mm 100 – 120 mm 120 – 140 mm 45 – 125 mm 78210583 Page 1 of 2 KATHREIN-Werke KG · Anton-Kathrein-Straße 1 – 3 · P.O. Box 10 04 44 · 83004 Rosenheim · Germany · Phone +49 8031 184-0 · Fax +49 8031 184-494 345 DTMA-1800-UMTS-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • Suitable for antenna RET control according to AISG/3GPP standard • Bypass mode to ensure cell operation in case of DC power down • Supports CWA, AISG 1.1 and AISG 2.0 (default) Ant 1 • Built-in lightning protection Ant 0 • AISG setting switchable • CWA and AISG configurations AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt CWA = Current Window Alarm Technical Data Type No. CWA alarm 78211103 78211105 DTMA-1800-UMTS-12-AISG-CWA 170 - 200 mA Node B 0 Node B 1 RET 230 - 295 mA 1800 MHz Tx Characteristics Frequency range Insertion loss Input power (per input) Intermodulation products in RX band Return loss 1805 - 1880 MHz Typically 0.5 dB < 100 W (+50 dBm) / < 1.6 kW (+62 dBm) peak Loss in bypass mode Return loss Gain Noise figure Output 1-dB compression point 3 order intercept point (OIP3) rd > 18 dB 1710 - 1785 MHz Typically 2.0 dB > 18 dB (DC ON) / > 12 dB (DC OFF) 12 dB nominal Typically 1.5 dB > 10 dBm Typically 25 dBm UMTS Tx Characteristics Frequency range 2110 - 2170 MHz Insertion loss Typically 0.4 dB Input power (per input) Intermodulation products in RX band Return loss < 100 W (+50 dBm) / < 1.6 kW (+62 dBm) peak < -117 dBm (2 Tx carriers at +43 dBm) > 18 dB UMTS Rx Characteristics Frequency range Loss in bypass mode Return loss Gain Noise figure Output 1-dB compression point 3rd order intercept point (OIP3) 1920 - 1980 MHz Typically 2.0 dB > 18 dB (DC ON) / > 12 dB (DC OFF) 12 dB nominal Typically 1.4 dB > 10 dBm Typically 25 dBm Environmental Characteristics Operating temperature range 346 Type No. < -117 dBm (2 Tx carriers at +43 dBm) 1800 MHz Rx Characteristics Frequency range Accessories (order separately) -40 ... +65 °C Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm DTMA-1800-UMTS-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) IP rating IP67* MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 Lightning protection 3 kA, 10/350 µs pulse DC and Alarm Characteristics CWA Mode AISG Mode DC supply 9 - 19 V DC 9 - 31 V DC Operating current per DTMA (without RET) 80 - 120 mA Nom. 300 mA at 10 V Nom. 100 mA at 30 V 78211103: 170 - 200 mA 78211105: 230 - 295 mA AISG* Alarm management Mechanical Characteristics Material Aluminium housing Connectors RF AISG Mounting 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 - 31 V DC, pin 7: DC return, other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Weight 8.0 kg Dimensions (w x h x d) 168 x 274 x 124 mm (without connectors, without mounting brackets) * see note on page 3 GSM 1800 GSM 1800 347 DTMA-1800-UMTS-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Compact line • Double units for easy use with XXPol antennas • Supports AISG 1.1 and 2.0 (default) AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt Ant 1 • Suitable for antenna RET control according to AISG/3GPP standard Ant 0 • Bypass mode to ensure cell operation in case of DC power down • Built-in lightning protection • DC Supply via Node B0, Node B1 or both Node B 0 RET 0 Technical Data 78211106 DTMA-1800-UMTS-12-AISG (12 dB gain) Type No. Tx Characteristics Frequency range 1805 - 1880 MHz 2110 - 2170 MHz Insertion loss Typically 0.5 dB Typically 0.4 dB Input power (per input) < 100 W (+50 dBm) / < 1.6 kw (+62 dBm) peak Intermodulation products in RX band < -117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 1710 - 1785 MHz Return loss 1920 - 1980 MHz > 18 dB (DC ON) / > 14 dB (DC OFF) Loss in bypass mode Typically 2.0 dB (DC OFF) 12 dB nominal Gain Noise figure Typically 1.5 dB Output 1-dB compression point 3rd order intercept point (OIP3) Typically 1.4 dB > 10 dBm Typically 25 dBm Environmental Characteristics Operating temperature range IP rating -40 ... +65 °C IP67* MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics DC supply 10 - 30 V Operating current per DTMA (without RET) Alarm management Nom. 300 mA at 10 V Nom. 100 mA at 30 V AISG* Mechanical Characteristics Material Connectors Aluminium housing RF AISG Mounting Weight Dimensions (w x h x d) * see note on data sheet 348 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 - 30 V DC, pin 7: DC return, other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 8.0 kg 168 x 274 x 120 mm (without connectors, without mounting brackets) RET 1 Node B 1 DTMA-1800-UMTS-12-AISG-D Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • • • • • • • Compact line Double units for easy use with XXPol antennas Supports AISG 1.1 and 2.0 (default) Suitable for antenna RET control according to AISG/3GPP standard Bypass mode to ensure cell operation in case of DC power down Built-in lightning protection DC Supply via Node B0, Node B1 or both AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt Ant 1 Ant 0 Technical Data 78210990 Type No. DTMA-1800-UMTS-12-AISG-D (12 dB gain) Tx Characteristics Node B0 AISG and DC-Port Node B 1 RET Connector configuration Frequency range Insertion loss Input power (per input) Intermodulation products in RX band 1805 - 1880 MHz 2110 - 2170 MHz Typically 0.5 dB Typically 0.3 dB < 100 W (+50 dBm) < -117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 1710 - 1785 MHz Return loss 1920 - 1980 MHz > 16 dB (DC ON) / > 12 dB (DC OFF) Loss in bypass mode Gain Typically 2.3 dB (DC OFF) 12 dB nominal Noise figure Typically 1.4 dB rd 3 order intercept point (OIP3) Typically 30 dBm Environmental Characteristics Operating temperature range IP rating -40 ... +65 °C IP67* MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics DC supply 10 - 30 V Operating current per DTMA (without RET) Alarm management Nom. 175 mA at 10 V Nom. 65 mA at 30 V AISG* Mechanical Characteristics Material Connectors Aluminium housing RF AISG Mounting Weight Packing size Dimensions (w x h x d) 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 - 30 V DC, pin 7: DC return, other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp set 6.5 kg 300 x 435 x 190 mm 220 x 220 x 80 mm (without connectors, without mounting brackets) * see note on data sheet 349 DTMA-1800-UMTS-12-AISG-D Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Blockdiagram 350 DTMA-AWS-12-AISG-CWA Fullband Duplex Tower Mounted Amplifier (Masthead Amplifier) • • • • • Double unit for easy use with XPol antennas Supports CWA, AISG 1.1 and AISG 2.0 (default) AISG setting swichable CWA and AISG configuration Suitable for antenna RET control according to AISG/3GPP standard • Compact size • Built-in lightning protection AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt CWA = Current Window Alarm Ant 0 Ant 1 Technical Data Node B 0 78210877 Type No. DTMA-AWS-12-AISG-CWA (12 dB gain) Node B 1 Tx Characteristics Frequency range 2110 - 2170 MHz Insertion loss Typically 0.3 dB Input power RET < 100 W (+50 dBm) Intermodulation products in RX band < -125 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 1710 - 1770 MHz Loss in bypass mode Return loss Typically 2.0 dB (DC OFF) > 18 dB (DC ON) / > 15 dB (DC OFF) Gain 12 dB nominal Noise figure Typically 1.3 dB Output 1-dB compression point > 10 dBm 3rd order intercept point (OIP3) Typically 25 dBm Environmental Characteristics Operating temperature range -40 ... +65 °C IP rating IP67* MTBF > 1 200 000 hours (per TMA) EMC According to EN 301 489-8 DC and Alarm Characteristics CWA Mode AISG Mode 9 - 19 V 9 - 30 V Operating current per TMA 80 - 130 mA Nom. 50 mA at 12 V Alarm management 170 - 180 mA AISG* DC supply Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm Aluminium housing 734362 80 - 100 mm 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 6: 9 - 30 V DC, pin 3: RS485B, pin 5: RS485A, pin 7: DC return, other pins: Not connected) 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm Mechanical Characteristics Material Accessories (order separately) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 2.5 kg 325 x 240 x 130 mm 152 x 174 x 50 mm (without connectors, without mounting brackets) 351 DTMA-1900-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • Supports CWA, AISG 1.1 and AISG 2.0 (default) • AISG setting swichable • CWA and AISG configuration AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt CWA = Current Window Alarm Ant 0 • Suitable for antenna RET control according to AISG/3GPP standard Ant 1 • By-pass mode to ensure cell operation in case of DC power down • Built-in lightning protection Technical Data 78210876 Type No. DTMA-1900-12-AISG-CWA (12 dB gain) Tx Characteristics Frequency range Node B 0 Node B 1 RET 1930 - 1990 MHz Insertion loss Typically 0.3 dB Input power (per input) Intermodulation products in RX band < 100 W (+50 dBm) < -117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Rx Characteristics Frequency range 1850 - 1910 MHz Loss in bypass mode Return loss Typically 2.0 dB (DC OFF) > 18 dB (DC ON) / > 15 dB (DC OFF) 12 dB nominal Gain Noise figure Typically 1.4 dB Output 1-dB compression point 3rd order intercept point (OIP3) > 10 dBm Typically 25 dBm Environmental Characteristics Operating temperature range -40 ... +65 °C IP rating IP67* MTBF > 1 200 000 hours (per TMA) EMC FCC Part 15 DC and Alarm Characteristics DC supply CWA Mode AISG Mode 9 - 19 V 9 - 30 V Operating current per TMA 80 - 130 mA Nom. 50 mA at 12 V Alarm management 170 - 180 mA AISG* Mechanical Characteristics Material Connectors Aluminium housing RF AISG Mounting Weight Packing size Dimensions (w x h x d) 352 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 - 30 V DC, pin 7: DC return, other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 4.6 kg 395 x 290 x 180 mm 168 x 275 x 61 mm (without connectors, without mounting brackets) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm DTMA-UMTS-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Slimline design • Double units for easy use with XPol antennas Supports: CWA, AISG CWA, 1.1 and AISG1.1 2.0and AISG 2.0 versions support AISG • Both 78210612 782 10610default defaultsetting: setting: AISG 1.1 AISG 2.0 default setting: AISG 2.0 782 10612 • AISG setting switchable as described on data sheet • CWA and AISG configurations as described on data sheet • Suitable for antenna RET control according to AISG/3GPP standard • Bypass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 1 Ant 0 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Technical Data Type No. Default setting AISG 1.1 170 – 200 mA Default setting AISG 2.0 170 – 200 mA 78210610 DTMA-UMTS-12-AISG-CWA (12 dB gain) 78210612 DTMA-UMTS-12-AISG-CWA (12 dB gain) Node B0 78211120 Default setting AISG 2.0 230 – 295 mA DTMA-UMTS-12-AISG-CWA (12 dB gain) Tx Characteristics Frequency range 2110 – 2170 MHz Insertion loss < 0.3 dB (typically 0.15 dB) Ripple < 0.1 dB Input power (per input) < 160 W (+52 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB RET Node B1 Rx Characteristics Frequency range 1920 – 1980 MHz Loss in bypass mode < 2.5 dB (DC OFF) Return loss > 18 dB (DC ON) / > 12 dB (DC OFF) Gain 12 ±1.0 dB (+22 … +28 °C) / 12 ±1.2 dB (– 40 ... +65 °C) Gain ripple < ±0.3 dB Noise figure* < 1.3 dB (+22 ... +28 °C) Output 1-dB compression point > 11 dBm 3rd order intercept point (OIP3) > 25 dBm (typically 30 dBm) DC and Alarm Characteristics DC supply Operating current per TMA (without RET) Alarm management 78210610 78210612 78211120 Mechanical Characteristics Material Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) –40 … +65 °C IP67 * > 1 000 000 hours (per TMA) According to ETS 300 342-3 CWA Mode 9 – 19 V 80 – 120 mA 170 – 200 mA 170 – 200 mA 230 – 295 mA AISG Mode 9 – 30 V Nom. 95 mA at 9 V Nom. 35 mA at 30 V AISG Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 3.8 kg 262 x 502 x 214 mm 160 x 205 x 63 mm (without connectors, without mounting brackets) Node B0 Node B1 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 – 60 mm 734361 60 – 80 mm 734362 80 – 100 mm 734363 100 – 120 mm 734364 120 – 140 mm 734365 45 – 125 mm * Noise figure NF = DTMAs Environmental Characteristics Operating temperature range IP rating MTBF EMC NF1920 MHz + 2 x NF1950 MHz + NF1980 MHz 4 (Additional variation at –40 ... +65 °C: NF < 0.3 dB) 339 353 DTMA-UMTS-24-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Slimline design • Double unit for easy use with XPol antennas • Supports CWA, AISG 1.1 and AISG 2.0 (default) • AISG setting switchable as described on data sheet • CWA and AISG configurations as described on data sheet • Suitable for antenna RET control according to AISG/3GPP standard • Bypass mode to ensure cell operation in case of DC power down • Built-in lightning protection Ant 0 Ant 1 RET = Remote Electrical Tilt AISG = Antenna Interface Standards Group CWA = Current Window Alarm Technical Data Type No. Tx Characteristics Frequency range Insertion loss Ripple Input power (per input) Intermodulation products in Rx band Return loss 78210613 DTMA-UMTS-24-AISG-CWA (24 dB gain) 2110 – 2170 MHz < 0.3 dB (typically 0.15 dB) < 0.1 dB < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak 1920 – 1980 MHz < 2.5 dB (DC OFF) > 18 dB (DC ON) / > 12 dB (DC OFF) 24 ±1.0 dB (+22 … +28 °C) / 24 ±1.2 dB (– 40 ... +65 °C) < ±0.3 dB < 1.4 dB (+22 ... +28 °C) > 18 dBm > 25 dBm (typically 30 dBm) Environmental Characteristics Operating temperature range IP rating MTBF EMC –40 … +65 °C IP67 * > 1 000 000 hours (per TMA) According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current per TMA (without RET) Alarm management Mounting Weight Packing size Dimensions (w x h x d) * Noise figure NF = CWA Mode 9 – 15 V 130 – 340 mA 380 – 420 mA AISG Mode 9 – 30 V Nom. 210 mA at 9 V Nom. 70 mA at 30 V AISG Aluminium housing 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 – 30 V DC, pin 7: DC return, other pins: not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 3.8 kg 262 x 502 x 214 mm 160 x 205 x 63 mm (without connectors, without mounting brackets) * see note on data sheet NF1920 MHz + 2 x NF1950 MHz + NF1980 MHz 4 (Additional variation at –40 ... +60 °C: NF < 0.4 dB) 342 354 RET Node B1 < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB Rx Characteristics Frequency range Loss in bypass mode Return loss Gain Gain ripple Noise figure* Output 1-dB compression point 3rd order intercept point (OIP3) Mechanical Characteristics Material Connectors RF AISG Node B0 Node B0 Node B1 Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 – 60 mm 734361 60 – 80 mm 734362 80 – 100 mm 734363 100 – 120 mm 734364 120 – 140 mm 734365 45 – 125 mm DTMA-1800-UMTS-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm 355 DTMA-UMTS-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Slimeline design • Double units for easy use with XPol antennas • Supports AISG 1.1 and 2.0 (default) • AISG setting switchable • Suitable for antenna RET control according to AISG/3GPP standard • Bypass mode to ensure cell operation in case of DC power down • Built-in lightning protection • Low weight Ant 0 Ant 1 AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt e B0 Node G and AISG DC-Port RET Node B1 B Technical Data 78211145 DTMA-UMTS-12-AISG (12 dB gain) Tx Characteristics Frequency range Insertion loss Ripple Input power (per input) Intermodulation products in RX band Return loss 2110 – 2170 MHz Typically 0.2 dB < 0.1 dB < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak < –117 dBm (2 Tx carriers at +43 dBm) > 18 dB Rx Characteristics Frequency range Loss in bypass mode Return loss Gain Noise figure 3rd order intercept point (OIP3) 1920 – 1980 MHz Typically 2.0 dB (DC OFF) > 18 dB (DC ON) Typically 12 dB Typically 1.4 dB Typically 30 dBm Environmental Characteristics Operating temperature range IP rating MTBF EMC –40 ... +65 °C IP67* > 1 000 000 hours (per TMA) According to ETS 300 342-3 DC and Alarm Characteristics DC supply Operating current (without RET) Alarm management AISG Mode 10 – 30 V Nom. 130 mA at 10 V Nom. 50 mA at 30 V AISG* Mechanical Characteristics Material Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) * see note on data sheet 356 Aluminium housing 7-16 female (long neck) 8-pin female, IEC 30130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 - 30 V DC, pin 7: DC return, other pins: Not connected) Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 3 kg 217 x 397 x 170 mm 138 x 191 x 71.6 mm (without connectors, without mounting brackets) Accessories (order separately) Type No. 734 360 734 361 734 362 734 363 734 364 734 365 Clamp set suitable for mast diameter of 34 – 60 mm 60 – 80 mm 80 – 100 mm 100 – 120 mm 120 – 140 mm 45 – 125 mm DTMAs Type No. 329 DTMA-UMTS-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • • • • • • • • Compact line Double units for easy use with XPol antennas Supports CWA, AISG 1.1 and 2.0 (default) AISG setting switchable as described on page 2 Suitable for antenna RET control according to AISG/3GPP standard By-pass mode to ensure cell operation in case of DC power down Built-in lightning protection Low weight Ant 0 AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt Ant 1 Technical Data Type No. 78211245 DTMA-UMTS-12-AISG-CWA (12 dB gain) Tx Characteristics Frequency range 2110 - 2170 MHz Insertion loss Typically 0.2 dB Ripple Input power (per input) Intermodulation products in RX band Node B0 AISG and DC-Port < 0.1 dB < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak < -117 dBm (2 Tx carriers at +43 dBm) Return loss Node B 1 RET Blockdiagram > 18 dB Rx Characteristics Frequency range Loss in by-pass mode Return loss 1920 - 1980 MHz Typically 2.0 dB (DC OFF) > 18 dB (DC ON) Gain Typically 12 dB Noise figure Typically 1.4 dB rd 3 order intercept point (OIP3) Typically 30 dBm Environmental Characteristics Operating temperature range -40 ... +65 °C IP rating IP67* MTBF > 1 000 000 hours (per TMA) EMC According to ETS 300 342-3 DC and Alarm Characteristics DC supply 7 - 19 V 10 - 30 V Operating current (without RET) 80 - 120 mA Nom. 130 mA at 10 V Nom. 50 mA at 30 V Alarm management 170 - 200 mA AISG* Mechanical Characteristics Material Connectors RF AISG Mounting Weight Packing size Dimensions (w x h x d) Node B0 Node B1 AISG Mode Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm Aluminium housing 734361 60 - 80 mm 7-16 female (long neck) 8-pin female, IEC 30130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 10 - 30 V DC, pin 7: DC return, other pins: Not connected) 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set 734365 45 - 125 mm 3 kg 217 x 397 x 170 mm 138 x 191 x 71.6 mm (without connectors, without mounting brackets) * see note on data sheet 357 DTMA-UMTS-BYP1800-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) • Double unit for easy use with XPol antennas • RF-Bypass for 1800 MHz • Suitable for antenna RET control according to AISG/3GPP standard • Bypass mode to ensure cell operation in case of DC power down Ant 0 • Supports CWA, AISG 1.1 and AISG 2.0 (default) • Built-in lightning protection • AISG setting switchable • CWA and AISG configuration AISG = Antenna Interface Standards Group RET = Remote Electrical Tilt CWA = Current Window Alarm BYP = RF-BYPass Node B 0 RET Node B 1 Technical Data Type No. CWA alarm 78211102 78211104 DTMA-UMTS-BYP1800-12-AISG-CWA (12 dB gain) 170 - 200 mA 230 - 295 mA UMTS 2100 Tx Characteristics Frequency range 2110 - 2170 MHz Insertion loss Typically 0.3 dB Input power (per input) Intermodulation products in RX band Return loss < 100 W (+50 dBm) < -117 dBm (2 Tx carriers at +43 dBm) > 18 dB UMTS 2100 Rx Characteristics Frequency range Loss in bypass mode Return loss Gain Noise figure 1920 - 1980 MHz Typically 2.0 dB (DC OFF) > 18 dB (DC ON) / > 12 dB (DC OFF) 12 dB nominal Typically 1.4 dB Output 1-dB compression point > 10 dBm 3 order intercept point (OIP3) Typically 25 dBm rd 1800 MHz Bypass Characteristics Frequency range 1800 Insertion loss 1710 - 1880 MHz Input power (per input) Intermodulation products in RX band Return loss 1710 - 1880 MHz Typically 0.2 dB < 100 W (+50 dBm) < -117 dBm (2 Tx carriers at +43 dBm) > 18 dB Environmental Characteristics Operating temperature range IP rating -40 ... +65 °C IP67* MTBF > 1 000 000 hours (per TMA) EMC According to ETS 301 489-8 Lightning protection 358 3 kA, 10/350 µs pulse Ant 1 DTMA-UMTS-BYP1800-12-AISG-CWA Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) DC and Alarm Characteristics CWA Mode AISG Mode DC supply 9 - 19 V DC 9 - 30 V DC Operating current 80 - 120 mA Nom. 100 mA at 12 V 78211102: 170 - 200 mA 78211104: 230 - 295 mA AISG* Alarm management Mechanical Characteristics Material Connectors Aluminium housing RF AISG 7-16 female (long neck) 8-pin female, IEC 60130-9 (Pin 3: RS485B, pin 5: RS485A, pin 6: 9 - 31 V DC, pin 7: DC return, other pins: Not connected) Mounting Wall mounting: With 4 screws (max. 8 mm diameter) Mast mounting: With additional clamp set Weight 4.0 kg Dimensions (w x h x d) 209 x 224 x 55 mm (without connectors, without mounting brackets) * see note on datasheet Accessories (order separately) Type No. Clamp set suitable for mast diameter of 734360 34 - 60 mm 734361 60 - 80 mm 734362 80 - 100 mm 734363 100 - 120 mm 734364 120 - 140 mm 734365 45 - 125 mm 359 DTMA-2600-12-AISG DTMA-2600-12-AISG Fullband Double Dual Duplex Tower Mounted Amplifier Fullband Double Dual Duplex Tower Mounted Amplifier (Masthead Amplifier) (Masthead Amplifier) • Double unit for easy use with XPol antennas • Double unit for easy use with XPol antennas • Supports AISG 1.1 and AISG 2.0 (default) • Supports AISG 1.1 and AISG 2.0 (default) • Suitable for antenna RET control according to AISG/3GPP standard • Suitable for antenna RET control according to AISG/3GPP standard • DC/AISG bypass between ports “Node B0 or Node B1” and “Ant 0” for DC/AISG ports “Node (incl. B0 orshort Nodecircuit B1” and “Ant 0” for supportbypass of RETbetween integrated antennas protection) •the the support of RET integrated antennas (incl. short circuit protection) • Bypass mode to ensure cell operation in case of DC power down • Bypass mode to ensure cell operation in case of DC power down • Built-in lightning protection • Built-in lightning protection Ant 0 Ant 0 Ant 1 Ant 1 RET = Remote Electrical Tilt RET = =Antenna RemoteInterface ElectricalStandards Tilt AISG Group AISG = Antenna Interface Standards Group Technical Data Technical Data Type No. Type No. Node B0 Node B0 RET RET 78210860 78210860 DTMA-2600-12-AISG (12 dB gain) DTMA-2600-12-AISG (12 dB gain) Tx Characteristics Tx Characteristics Frequency range 2620 – 2690 MHz Frequency range 2620 – 2690 MHz Insertion loss Typically 0.3 dB Insertion loss Typically 0.3 dB Ripple < 0.35 dB Ripple < 0.35 dB Input power (per input) < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak Input power (per input) < 100 W (+50 dBm) CW / < 1.6 kW (+62 dBm) peak Intermodulation products products inIntermodulation Rx band < –117 dBm (2 Tx carriers at +43 dBm) in Rx band < –117 dBm (2 Tx carriers at +43 dBm) Return loss > 18 dB Return loss > 18 dB Rx Characteristics Rx Characteristics Frequency 2500 Frequencyrange range 2500––2570 2570MHz MHz Loss Typically Lossininbypass bypassmode mode Typically22dB dB Return >>18 Returnloss loss 18dB dB(DC (DCON) ON) Gain 12 Gain 12dB dBnominal nominal Noise Typically Noisefigure figure Typically1.2 1.2dB dB Output 1-dB compression point > 13 dBm Output 1-dB compression point > 13 dBm 3rd3rdorder Typically orderintercept interceptpoint point(OIP3) (OIP3) Typically30 30dBm dBm Environmental Characteristics Environmental Characteristics Operating –40 Operatingtemperature temperaturerange range –40… …+65 +65°C °C IPIPrating IP67 (see note on rating IP67 (see note ondata datasheet) sheet) MTBF >>11000 MTBF 000000 000hours hours(per (perTMA) TMA) EMC According EMC AccordingtotoETS ETS300 300342-3 342-3 DC DCand andAlarm AlarmCharacteristics Characteristics DC 10 DCsupply supply 10––30 30VV Operating Nom. Operatingcurrent currentper perDTMA DTMA Nom.175 175mA mAatat10 10VVDC DC (without Nom. Accessories (withoutRET) RET) Nom.70 70mA mAatat30 30VVDC DC Accessories (order (order separately) separately) Alarm AISG Alarmmanagement management AISG Clamp Mechanical Clamp set set MechanicalCharacteristics Characteristics Type suitable TypeNo. No. suitable for for mast mast Material Aluminium Material Aluminiumhousing housing diameter diameter of of Connectors RF 7-16 Connectors RF 7-16female female(long (longneck) neck) 8-pin AISG 8-pinfemale, female,IEC IEC60130-9 60130-9 AISG 734360 34 734360 34 –– 60 60 mm mm (Pin (Pin3:3:RS485B, RS485B,pin pin5:5:RS485A, RS485A,pin pin6:6: 10 10––30 30VVDC, DC, pin 734361 60 pin7:7:DC DCreturn, return,other otherpins: pins:not notconnected) connected) 734361 60 –– 80 80 mm mm Mounting Wall Mounting Wallmounting: mounting:With With44screws screws(max. (max.88mm mmdiameter) diameter) 734362 80 – 100 mm 734362 80 – 100 mm Mast Mastmounting: mounting:With Withadditional additionalclamp clampset set Weight 3.5 734363 100 – 120 mm Weight 3.5kg kg 734363 100 – 120 mm Packing 217 Packingsize size 217xx407 407xx144 144mm mm 734364 120 734364 120 –– 140 140 mm mm Dimensions 165.3 Dimensions(w(wx xh hx xd)d) 165.3xx236.4 236.4xx65.1 65.1mm mm 734365 45 – 125 mm (without connectors, without mounting brackets) 45 – 125 mm (without connectors, without mounting brackets) 734365 * see note on data sheet 360 332 332 Node B1 Node B1 Clamp Set Subsidiaries/Affiliates mobilcom@kathrein.de Internet: www.kathrein.de KATHREIN-Werke KG · Phone +49 80 31 184-0 · Fax +49 80 31 184-820 Anton-Kathrein-Straße 1 – 3 · P.O. Box 10 04 44 · D-83004 Rosenheim · Germany 9981.1964/1212/4/ZWT/MM For technical information, orders, catalogues or CD-ROM, please contact: Subject to alteration. An actual list of Kathrein’s International Representatives can be found on our homepage: www.kathrein.de

698 – 6000 MHz Base Station Antennas Filters Combiners and Amplifiers for Mobile Communications 2013

Add this document to collection(s)

Add this document to saved

Suggest us how to improve StudyLib