2/3/23, 3:35 PM
2008 Nissan Xterra Remote Programming – Free Keyless Entry Remote Key Fob Programming Instructions
2008 Nissan Xterra Remote Programming
This procedure will not work for vehicles that have Intelligent Key System (also called push button ignition)
Note: You must have all remotes on hand when performing this procedure. Any remotes not used during this
procedure will become inactive.
1. Close and lock all doors with the driver’s side power lock switch located on drivers door panel.
2. Insert key into ignition (DON’T TURN) and remove it from the ignition key cylinder at least 6 times within
10 seconds (this will need to be done at approximately one second intervals). You may need to insert and
remove the key up to 10 or 12 times until your hazard lamps flash. PLEASE NOTE: Withdraw key
completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system
will not enter programming mode.
3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash. PLEASE
NOTE: Do not press the button on the remote more than one time or the programming will not be
JustAnswer
wsnAtsu
nAtsuJ
successful.
Chat w/ an expert Online
Now
Open
5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch
on drivers door panel. Within 5 seconds of locking and unlocking doors press LOCK button on the next
remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the
ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door. Test all
remotes.
How to program a replacement Nissan Keyless Remote Key Fob Transmitter
Chat w/ an expert Online Now
A Technician Will Answer Your Questions in Minutes. Chat Now. JustAnswer
Open

https://www.keyfobprogram.com/2008-nissan-xterra-remote-programming/
1/1
2/3/23, 3:37 PM
2008 Nissan Xterra Keyless Entry Remote Fob Smart Key Programming Instructions
Vehicle Make
Acura
Audi
2008 Nissan Xterra Keyless Entry Remote Fob Smart
Key Programming Instructions
BMW
Buick
Cadillac
Chevrolet
Instructions
Chrysler
Dodge
How to Program a 2008 Nissan Xterra Keyless Entry Remote Fob Smart Key
Ford
Step by Step How to Program Instructions:
Genesis
IMPORTANT: Before entering programming mode, have in possession all of the transmitters
you will be using on the vehicle. Once you program the transmitter, all previous codes will be
erased from the memory. The other transmitters will not be functional until you program the
transmitters again.
GMC
Honda
Hummer
Hyundai
1. Close and lock all doors with the driver’s side power lock/unlock switch.
Infiniti
Isuzu
2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10
seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw
key completely from ignition cylinder each time. If this procedure is performed too fast, system will not
enter programming mode.
Jaguar
Jeep
Kia
Lexus
3. Insert key into the ignition cylinder and turn to the ACC position.
Lincoln
4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash.
NOTE: Do not press the button more than one time in the above step. If the button is pressed more
than one time, the programming procedure will not be successful.
Mazda
Mercury
Mitsubishi
Nissan
Oldsmobile
Plymouth
Polestar
5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the
driver’s side power lock/unlock switch and within 5 seconds, push ANY button on the next remote.
Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing
transmitters).
6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side
power lock/unlock switch and open the driver side door.
Pontiac
Ram
Even if your original key and remote were separate, you can upgrade to a key with built-in remote
buttons.
Saturn
Scion
Subaru
Suzuki
Toyota
Volkswagen
Volvo
If you have one working key Click Here to Buy Key and Programmer.
Information
Video
Home
YouTube
Disclaimer
Privacy Policy
Go to LocateALocksmith.com
to find a Locksmith in your area.
Home | Disclaimer | YouTube | Privacy Policy
Copyright © 2023 ProgramYourRemote.com
All Rights Reserved.
Chat w/ an expert Online Now
Open
A Technician Will Answer Your Questions in Minutes. Chat Now. JustAnswer
https://www.programyourremote.com/classified/2008-nissan-xterra-keyless-entry-remote-fob-smart-key-programming-instructions-listing-5987.aspx
1/1