Uploaded by Deepanshu Barve

deepanshu idea Generation ppt

advertisement
UNIVERSITY INSTITUTE OF TECHNOLOGY–RGPV BHOPAL
UNIVERSITY INSTITUTE OF TECHNOLOGY–RGP BHOPAL
Department
of ELECTRONICS & COMMUNICATION
Department of ELECTRONICS & COMMUNICATION
Name-Deepanshu Barve
Enrollment No.-0101EC211044
Subject-Idea Generation Lab PPT
Branch-ECE ‘A’
Semester-3rd
SUBMITED TO –Ms.AKANSHA PARHIHAR
It is a simple dustbin whose operation is controlled by arduino uno.
1.INTRODUCTION
CONTENTS
C O N T E N T S
2. CURRENT SYSTEM
3. PROPOSED SYSTEM
4. CONCLUTION
Part 01
Add
your title
INTRODUCTION
INTRODUCTION
• Currently almost a huge amount of earth is filled
with garbage and is a big problem
• This can lead to many environmental problems
• Endangers life of animals also
• Leads to atmospheric pollution
• Spreads diseases
• All these problems are due to improper waste
disposal
INSERT
LOGO
Part 02
Part 01
CURRENT
Add your title
SYSTEM
CURRENT SYSTEM
INSERT
LOGO
DRAWBACKS OF CURRENT SYSTEM
• Garbage overflow
• Unhealthy and untidy surroundings
• Cannot cope up with the amount of garbage
INSERT
LOGO
Part 03
Part 01
PROPOSED
Add
your title
SYSTEM
PROPOSED SYSTEM
• It continuously monitors the level of garbage in
the bin
• Bin opens automatically when a person
approaches the bin
• Informs authorities when it needed to be cleared
INSERT
LOGO
ABSTRACT
INSERT
LOGO
This paper presents a cost-effective design of an intelligent waste
container for small-scale cases.This system is basedon Arduino
Uno board and an ultrasonic sensor to monitor the fullness level of
the container and give SMS alerts using a GSM module and lid of
the container will automatically opens itself upon detection of human
hand by suing a PIR motion sensor.The system is powered by
lithium battery.The system provides an option of charging external
portable devices using the power bank.Finally,the system is
implemented successfully with an acceptable overall cost for the
intended application.The system performance was found
satisfactory according to the obtained test results.
COMPONENTS
1. Arduino UNO
2. HC-SRO4 Ultrasonic Sensor Module
3. TowerPro SG90 Servo Motor
4. A small dustbin with hinged lid
5. 9V Power Supply
COMPONENTS
6. Connecting Wires
7. GSM module
8. PIR motion sensor
ADRUINO UNO
•
•
It is the key component of the system
Programmed to
1.
Check the status of bin
2.
Inform the authorised person
3.
Opens when a person alproaches
GSM MODULE
It helps to send the status of the bin
to the authorised persons when the bin is full.
When the garbage level reaches its maximum
level it sends “IAM FULL” message to the reserved
authority
ULTRASONIC
SENSOR
It helps to find the waste level , and when
it exceeds a particular limit it send signals
to adruino
PIR MOTION
SENSOR
It detects the motion of the persor nearby
and when a motion is detected it will send
signals to tha adruino
SERVO MOTOR
It will rotate and opens the bin when
siganal is obtained from adruino
CIRCUIT DIAGRAM
INSERT
LOGO
Initialise
adruino,
gsm & ul
trasonic s
ensor
WORKING
Pir senso
r initialis
es
Pir senso
r detects t
he move
ment
Ultrasonic
sensor mea
sure the dis
tance
If distance i
s less than li
mit adruino
send signal
to gsm
Gsm mod
ule will se
nd sms to
desired no
Adruino
send
signal to
servo
motor
motor rot
ates and b
in opens
INSERT
LOGO
ADVANTAGES & DISADVANTAGES
ADVATAGES
* Helps in avoiding garbage
overflow
• Low operating cost
• Low maintenance
requirements
• Requires manual recharging
of mobile network subscription
• Security measures depend on
build quality and fixed
installation of the bin
• Don’t send an alert in case of
fire
DISADVANTAGES
Part 04
Part
01
Add
your title
CONCLUSION
CONCLUSION
INSERT
LOGO
By using this method of waste collection, mainly
in urban areas, becomes more easier. It helps in
reducing air pollution, traffic flow, time,
manpower and money. This project can add an
edge to the cities aiming to get smart and
people-friendly.
THANK
YOU
Download