PANEL ANTENNAS
WITH TWO LOW BAND ARRAYS
22 | April 2015
TwinLine
Quad antennas with two
multiband arrays housed
in an optimally designed
package for low windload.
Ideal for site/technology
sharing.
April 2015 | 23
(2x) 698-960 / 1695-2690 / 1695-2690 MHz
5980300
5980300A
5980300G
5980300DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt
•
•
•
•
•
Twin tri band antenna, dual polarisation, 12 connectors
Independent tilt on each band 0-10° / 0-12° / 0-12°
Lightweight TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5980300
Remote Electrical Tilt AISG1.1
5980300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5980300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator
5980300DG
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
R1
R2
Y1
Y3
Ultra Wide Band Bottom System
1695-2690 MHz Ports
(4x) 7/16-DIN Female Long Neck
Y2
Y4
Ultra Wide Band Top System
1695-2690 MHz Ports
(4x) 7/16-DIN Female Long Neck
Ultra Low Band
698-960 MHz Ports
Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)
Tilt 0°
Tilt Mid Value
Tilt Max Value
R1-R2
(4x) 7/16-DIN Female Long Neck
Y1-Y3 (Bottom)
Y2-Y4 (Top)
700
800
900
1800
2100
2600
1800
2100
2600
15.5
15.5
15.2
16.5
16.4
16.2
17.4
17.3
17.0
17.1
17.1
17.1
17.5
17.5
17.4
18.0
18.0
17.8
17.1
17.1
17.1
17.5
17.5
17.4
18.0
18.0
17.8
Input Impedance
50Ω
50Ω
50Ω
VSWR
< 1.5
< 1.5
< 1.5
Polarisation
±45°
Horizontal Beamwidth (-3 dB)
75°
Vertical Beamwidth (-3 dB)
8.6°
±45°
68°
65°
65°
7.5°
6.7°
7.0°
±45°
63°
61°
65°
6.4°
5.2°
6.5°
63°
61°
5.9°
4.7°
Electrical Downtilt Range
0-10°
0-12°
0-12°
Inter/Intra Band Isolation
> 30 dB, > 28 dB from 0° to 2° tilt
> 30 dB, > 28 dB from 0° to 2° tilt
> 30 dB, > 28 dB from 0° to 2° tilt
18 dB Typical
18 dB Typical
18 dB Typical
> 30 dB
> 25 dB
> 30 dB
> 25 dB
> 30 dB
> 25 dB
Maximum Power (Per Port)
250 W
200 W
200 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
< -110 dBm
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back
Ratio
@ 180°
@ 180° ±30°
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
(MCDU)
RET-Ready
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt
(RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas
with factory embedded motors (for antenna sharing or two technologies). Refer to ordering
options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
24 | April 2015
(2x) 698-960 / 1695-2690 / 1695-2690 MHz
5980300
5980300A
5980300G
5980300DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt
Environmental
Packaging
Operating Temperature Range
-40° C to +60° C
Environmental
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
59 kg
Includes 0900181/00 Kit
ETS 300 019
RoHS Compliant
Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth)
2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
48 kg
Shroud
Outdoor Fibreglass, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 150 km/h
Frontal: 990 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 555 N
Rear: 920 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
698-960 MHz
YELLOW
1695-2690 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 25
(2x) 790-960 / 1710-2170 / 2500-2690 MHz
5982200
5982200A
5982200G
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
• Twin tri band antenna, dual polarisation, 12 connectors
• Independent tilt on each band 0-10° / 0-12° / 0-12°
LTE 800 Ready
LTE 2600 Ready
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0
• Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options
Model Number
Manual Electrical Tilt
5982200
Remote Electrical Tilt AISG1.1
5982200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5982200G
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
RED and GREEN Rings
Low Band
790-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
YELLOW Rings
High Band (Top Array)
2500-2690 MHz Ports
(4x) 7/16-DIN Female Long Neck
BLUE Rings
High Band (Bottom Array)
1710-2170 MHz Ports
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)
Tilt 0°
Tilt Mid Value
Tilt Max Value
Low Band (RED or GREEN)
High Band (BLUE)
High Band (YELLOW)
790...880...960
1710...1880
1900...2170
2500...2690
16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4
16.5...16.9
16.4...16.7
16.3...16.5
16.9...17.3
16.7...17.2
16.5...17.0
17.4...17.8
17.3...17.7
17.2...17.5
Input Impedance
50Ω
50Ω
50Ω
VSWR
< 1.5
< 1.5
< 1.5
Polarisation
±45°
±45°
Horizontal Beamwidth (-3 dB)
75°...68°...63°
65°
±45°
62°
60°
Vertical Beamwidth (-3 dB)
7°
7°
5°
Electrical Downtilt Range
0-10°
0-12°
0-12°
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
45 dB Typical
45 dB Typical
45 dB Typical
> 30 dB
> 30 dB
> 30 dB
18 dB Typical
18 dB Typical
18 dB Typical
Intra Band Isolation
Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back Ratio
> 30 dB
> 30 dB
> 30 dB
Maximum Power (Per Port)
200 W
160 W
160 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET Module Part Number
(one per antenna)
MDCU-A0000
for AISG1.1 protocol (one unit included in 5982200A)
MDCU-G0000
for 3GPP/AISG2.0 protocol (one unit included in 5982200G)
Environmental
Operating Temperature Range
Environmental
RoHS
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
26 | April 2015
(2x) 790-960 / 1710-2170 / 2500-2690 MHz
5982200
5982200A
5982200G
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
Packaging
Mechanical Characteristics
Dimensions (Height x Width x Depth)
2700 x 442 x 152 mm (219 mm with Rear Connectors)
Weight (Excluding Mounting Accessories)
56 kg
Shroud
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3 | 70 kg
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 160 km/h
Frontal: 1300 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 220 N
Rear: 1700 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
Not available
---
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
790-960 MHz
GREEN
790-960 MHz
BLUE
1710-2170 MHz
YELLOW
2500-2690 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 27
(2x) 790-960 / 1710-2170 / 2500-2690 MHz
5982200 lv
5982200A lv
(lightweight version)
5982200G lv
5982200DG lv
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
•
•
•
•
•
Twin tri band antenna, dual polarisation, 12 connectors
Independent tilt on each band 0-10° / 0-12° / 0-12°
Lightweight TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5982200 lv
Remote Electrical Tilt AISG1.1
5982200A lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5982200G lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22)
5982200DG lv
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
RED and GREEN Rings
Low Band
790-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
YELLOW Rings
High Band (Top Array)
2500-2690 MHz Ports
(4x) 7/16-DIN Female Long Neck
BLUE Rings
High Band (Bottom Array)
1710-2170 MHz Ports
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Low Band (RED or GREEN)
Frequency Bands (MHz)
Gain (dBi)
Tilt 0°
Tilt Mid Value
Tilt Max Value
High Band (BLUE)
High Band (YELLOW)
790...880...960
1710...1880
1900...2170
2500...2690
16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4
16.5...16.9
16.4...16.7
16.3...16.5
16.9...17.3
16.7...17.2
16.5...17.0
17.2...17.6
17.1...17.5
17.0...17.3
Input Impedance
50Ω
50Ω
50Ω
VSWR
< 1.5
< 1.5
< 1.5
Polarisation
±45°
Horizontal Beamwidth (-3 dB)
75°...68°...63°
±45°
65°
±45°
62°
60°
Vertical Beamwidth (-3 dB)
7°
7°
5°
Electrical Downtilt Range
0-10°
0-12°
0-12°
> 28 dB
> 27 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
Intra Band Isolation
Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back Ratio
45 dB Typical
45 dB Typical
45 dB Typical
> 28 dB (900 Band)
> 27 dB (800 Band)
> 30 dB
> 30 dB
18 dB Typical
18 dB Typical
18 dB Typical
> 25 dB
> 25 dB
> 30 dB
Maximum Power (Per Port)
200 W
160 W
160 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
28 | April 2015
(2x) 790-960 / 1710-2170 / 2500-2690 MHz
5982200 lv
5982200A lv
(lightweight version)
5982200G lv
5982200DG lv
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
Environmental
Packaging
Operating Temperature Range
-40° C to +60° C
Environmental
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
59 kg
Includes 0900181/00 Kit
ETS 300 019
RoHS Compliant
Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth)
2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
48 kg
Shroud
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
at 150 km/h
Wind Load
(EN1991-4-1)
at 160 km/h
Mounting Kit Options
Survival: 200 km/h
Frontal: 990 N
Lateral: 555 N
Rear: 920 N
Highest value: 1450 N at 110°
Frontal: 1130 N
Lateral: 630 N
Rear: 1045 N
Highest value: 1650 N at 110°
Part Number
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
790-960 MHz
GREEN
790-960 MHz
BLUE
1710-2170 MHz
YELLOW
2500-2690 MHz
2683
432
RED
153
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
1865
Location of the MDCU
for RET Control
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 29
(2x) 790-960 / 1710-2170 / 1710-2170 MHz
5980200
5980200A
5980200G
5980200DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
• Twin tri band antenna, dual polarisation, 12 connectors
• Independent tilt on each band 0-10° / 0-12° / 0-12°
LTE 800 Ready
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0
• Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options
Model Number
Manual Electrical Tilt
5980200
Remote Electrical Tilt AISG1.1
5980200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5980200G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22)
5980200DG
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
RED and GREEN Rings
WHITE Rings
BLUE Rings
Low Band
790-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
High Band (Top Array)
1710-2170 MHz Ports
(Wide Band)
(4x) 7/16-DIN Female Long Neck
High Band (Bottom Array)
1710-2170 MHz Ports
(Wide Band Optimised for UMTS)
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Low Band (RED or GREEN)
Frequency Bands (MHz)
790...880
880...960
1710...1880
1900...2170
1710...1880
1900...2170
17.2
17.5
16.5...16.7
16.3...16.5
16.0...16.3
16.7...17.2
16.5...17.0
16.3...16.5
16.5...16.9
16.4...16.7
16.3...16.5
16.9...17.3
16.7...17.2
16.5...17.0
Gain (dBi)
Tilt 0°
Tilt Mid Value
Tilt Max Value
High Band (WHITE)
High Band (BLUE)
Input Impedance
50Ω
50Ω
50Ω
VSWR
< 1.5
< 1.4
< 1.4
Polarisation
Horizontal Beamwidth (-3 dB)
±45°
75°
±45°
68°
65°
65°
7°
7°
62°
Vertical Beamwidth (-3 dB)
7°
Electrical Downtilt Range
0-10°
0-12°
0-12°
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
45 dB Typical
45 dB Typical
45 dB Typical
> 29 dB
> 30 dB
> 30 dB
18 dB Typical
18 dB Typical
18 dB Typical
Intra Band Isolation
Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back Ratio
7°
±45°
62°
7°
> 30 dB
> 30 dB
> 30 dB
Maximum Power (Per Port)
200 W
160 W
160 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
30 | April 2015
(2x) 790-960 / 1710-2170 / 1710-2170 MHz
5980200
5980200A
5980200G
5980200DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
Environmental
Packaging
Operating Temperature Range
-40° C to +60° C
Environmental
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3 | 70 kg
ETS 300 019
RoHS Compliant
Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth)
2700 x 442 x 152 mm (219 mm with Rear Connectors)
Weight (Excluding Mounting Accessories)
56 kg
Shroud
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 160 km/h (EN1991-4-1)
Frontal: 1512 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 512 N
Rear: 1418 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
790-960 MHz
GREEN
790-960 MHz
WHITE
1710-2170 MHz
BLUE
1710-2170 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 31
(2x) 790-960 / 1710-2170 / 1710-2170 MHz
5980200 lv
5980200A lv
(lightweight version)
5980200G lv
5980200DG lv
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
•
•
•
•
•
Twin tri band antenna, dual polarisation, 12 connectors
Independent tilt on each band 0-10° / 0-12° / 0-12°
Lightweight TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5980200 lv
Remote Electrical Tilt AISG1.1
5980200A lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5980200G lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22)
5980200DG lv
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
RED and GREEN Rings
Low Band
790-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
WHITE Rings
High Band (Top Array)
1710-2170 MHz Ports
(Wide Band)
(4x) 7/16-DIN Female Long Neck
BLUE Rings
High Band (Bottom Array)
1710-2170 MHz Ports
(Wide Band Optimised for UMTS)
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Low Band (RED or GREEN)
Frequency Bands (MHz)
790...880
880...960
1710...1880
1900...2170
1710...1880
1900...2170
17.2
17.5
16.5...16.7
16.3...16.5
16.0...16.3
16.7...17.2
16.5...17.0
16.3...16.5
16.5...16.9
16.4...16.7
16.3...16.5
16.9...17.3
16.7...17.2
16.5...17.0
Gain (dBi)
Tilt 0°
Tilt Mid Value
Tilt Max Value
High Band (WHITE)
High Band (BLUE)
Input Impedance
50Ω
50Ω
50Ω
VSWR
< 1.5
< 1.4
< 1.4
Polarisation
Horizontal Beamwidth (-3 dB)
±45°
75°
±45°
68°
±45°
65°
62°
65°
7°
7°
7°
62°
Vertical Beamwidth (-3 dB)
7°
Electrical Downtilt Range
0-10°
0-12°
0-12°
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
45 dB Typical
45 dB Typical
45 dB Typical
> 29 dB
> 30 dB
> 30 dB
18 dB Typical
18 dB Typical
18 dB Typical
> 30 dB
> 30 dB
> 30 dB
Maximum Power (Per Port)
200 W
160 W
160 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
< -110 dBm
Intra Band Isolation
Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back Ratio
7°
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
32 | April 2015
(2x) 790-960 / 1710-2170 / 1710-2170 MHz
5980200 lv
5980200A lv
(lightweight version)
5980200G lv
5980200DG lv
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
Environmental
Packaging
Operating Temperature Range
-40° C to +60° C
Environmental
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
59 kg
Includes 0900181/00 Kit
ETS 300 019
RoHS Compliant
Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth)
2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
48 kg
Shroud
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
at 150 km/h
Wind Load
(EN1991-4-1)
at 160 km/h
Mounting Kit Options
Survival: 200 km/h
Frontal: 990 N
Lateral: 555 N
Rear: 920 N
Highest value: 1450 N at 110°
Frontal: 1130 N
Lateral: 630 N
Rear: 1045 N
Highest value: 1650 N at 110°
Part Number
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
GREEN
790-960 MHz
WHITE
1710-2170 MHz
BLUE
1710-2170 MHz
432
790-960 MHz
153
RED
1865
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
2683
Location of the MDCU or MDDU
for RET Control
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 33
(2x) 698-960 / 1695-2690 MHz
5961300
5961300A
5961300G
5961300DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt
•
•
•
•
•
Twin dual band antenna, dual polarisation, 8 connectors
Independent tilt on each band 0-10° / 0-10°
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5961300
Remote Electrical Tilt AISG1.1
5961300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5961300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator
5961300DG
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.
R1
R2
Ultra Low Band
698-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
Y1
Y2
Ultra Wide Band
1695-2690 MHz Ports
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)
Tilt 0°
Tilt 5°
Tilt 10°
R1-R2
Y1-Y2
700
800
900
1800
2100
2600
15.5
15.5
15.2
16.5
16.4
16.2
17.4
17.3
17.0
17.7
17.7
17.7
18.1
18.1
18.0
18.5
18.5
18.2
Input Impedance
50Ω
50Ω
VSWR
< 1.5
< 1.5
Polarisation
±45°
±45°
Horizontal Beamwidth (-3 dB)
75°
68°
65°
65°
63°
61°
Vertical Beamwidth (-3 dB)
8.6°
7.5°
6.7°
6.1°
5.3°
4.2°
Electrical Downtilt Range
0-10°
0-10°
Inter/Intra Band Isolation
> 30 dB, > 28 dB from 0° to 2° tilt
> 30 dB, > 28 dB from 0° to 2° tilt
18 dB Typical
18 dB Typical
> 30 dB
> 25 dB
> 30 dB
> 25 dB
Maximum Power (Per Port)
250 W
200 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back
Ratio
@ 180°
@ 180° ±30°
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
34 | April 2015
(2x) 698-960 / 1695-2690 MHz
5961300
5961300A
5961300G
5961300DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt
Mechanical Characteristics
Packaging
Dimensions (Height x Width x Depth)
2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
44 kg
Shroud
Outdoor Fibreglass, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 150 km/h
Frontal: 990 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 555 N
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
55 kg
Includes 0900181/00 Kit
Rear: 920 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
698-960 MHz
YELLOW
1695-2690 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 35
(2x) 790-960 / 1710-2170 MHz
5961200
5961200A
5961200G
5961200DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt
• Twin dual band Antenna, dual polarisation, 8 connectors
• Independent tilt on each band 0-10° / 0-10°
LTE 800 Ready
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0
• Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options
Model Number
Manual Electrical Tilt
5961200
Remote Electrical Tilt AISG1.1
5961200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5961200G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12)
5961200DG
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.
RED | GREEN Rings
Low Band
790-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
WHITE | BLUE Rings
High Band
1710-2170 MHz Ports (Wide Band)
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Low Band (RED or GREEN)
Frequency Bands (MHz)
Gain (dBi)
Tilt 0°
Tilt 5°
Tilt 10°
High Band (WHITE or BLUE)
790...880...960 MHz
1710...1880
1900...2170
16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4
17.8...18.2
17.7...18.0
17.6...17.8
18.2...18.6
18.0...18.5
17.8...18.3
Input Impedance
50Ω
50Ω
VSWR
< 1.5
< 1.5
Polarisation
±45°
±45°
Horizontal Beamwidth (-3 dB)
Vertical Beamwidth (-3 dB)
Electrical Downtilt Range
Intra Band Isolation
Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back Ratio
75°...68°...63°
65°
62°
7.0°
5.5°
5.0°
0-10°
0-10°
> 28 dB
> 30 dB, > 28 dB from 0° to 2° tilt
45 dB Typical
45 dB Typical
> 25 dB for 790-880 MHz
> 28 dB for 880-960 MHz
> 30 dB
18 dB Typical
18 dB Typical
> 30 dB
> 30 dB
Maximum Power (Per Port)
200 W
160 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control
RET-Ready
Unit (MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
36 | April 2015
(2x) 790-960 / 1710-2170 MHz
5961200
5961200A
5961200G
5961200DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt
Mechanical Characteristics
Packaging
Dimensions (Height x Width x Depth)
2700 x 442 x 152 mm
Weight (Excluding Mounting Accessories)
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3 | 67 kg
52 kg
Shroud
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 160 km/h (EN1991-4-1)
Frontal: 1512 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 512 N
Rear: 1418 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
790-960 MHz
GREEN
790-960 MHz
BLUE
1710-2170 MHz
WHITE
1710-2170 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 37
(2x) 790-960 / 1710-2170 MHz
5961200 lv
5961200A lv
(lightweight version)
5961200G lv
5961200DG lv
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt
•
•
•
•
•
Twin dual band antenna, dual polarisation, 8 connectors
Independent tilt on each band 0-10° / 0-10°
Lightweight TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
LTE 800 Ready
Ordering Options
Model Number
Manual Electrical Tilt
5961200 lv
Remote Electrical Tilt AISG1.1
5961200A lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5961200G lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12)
5961200DG lv
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.
RED | GREEN Rings
Low Band
WHITE | BLUE Rings
High Band
Electrical Characteristics
(4x) 7/16-DIN Female Long Neck
1710-2170 MHz Ports
(4x) 7/16-DIN Female Long Neck
Low Band (RED or GREEN)
Frequency Bands (MHz)
Gain (dBi)
790-960 MHz Ports
Tilt 0°
Tilt 5°
Tilt 10°
High Band (WHITE or BLUE)
790...880...960 MHz
1710...1880
1900...2170
16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4
17.8...18.2
17.7...18.0
17.6...17.8
18.2...18.6
18.0...18.5
17.8...18.3
Input Impedance
50Ω
50Ω
VSWR
< 1.5
< 1.5
Polarisation
±45°
Horizontal Beamwidth (-3 dB)
±45°
75°...68°...63°
65°
62°
Vertical Beamwidth (-3 dB)
7.0°
5.5°
5.0°
Electrical Downtilt Range
0-10°
0-10°
Intra Band Isolation
Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back Ratio
> 28 dB
> 30 dB, > 28 dB from 0° to 2° tilt
45 dB Typical
45 dB Typical
> 25 dB for 790-880 MHz
> 28 dB for 880-960 MHz
> 30 dB
18 dB Typical
18 dB Typical
> 30 dB
> 30 dB
Maximum Power (Per Port)
200 W
160 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control
RET-Ready
Unit (MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
38 | April 2015
(2x) 790-960 / 1710-2170 MHz
5961200 lv
5961200A lv
(lightweight version)
5961200G lv
5961200DG lv
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt
Mechanical Characteristics
Packaging
Dimensions (Height x Width x Depth)
2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3 | 59 kg
44 kg
Shroud
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load
(EN1991-4-1)
Survival: 200 km/h
at 150 km/h
Frontal: 990 N
Lateral: 555 N
Rear: 920 N
Highest value: 1450 N at 110°
at 160 km/h
Frontal: 1130 N
Lateral: 630 N
Rear: 1045 N
Highest value: 1650 N at 110°
Mounting Kit Options
Part Number
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
790-960 MHz
GREEN
790-960 MHz
BLUE
1710-2170 MHz
WHITE
1710-2170 MHz
2683
432
RED
153
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
1865
Location of the MDCU or MDDU
for RET Control
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 39
(2x) 698-960 MHz
5920300
5920300A
5920300G
5920300DG
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
•
•
•
•
•
Twin low band, dual polarisation, 4 connectors
Independent tilt on each band 0-10°
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5920300
Remote Electrical Tilt AISG1.1
5920300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5920300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator
5920300DG
Access Ports Description (Connectors)
This antenna is built with two identical Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded
connectors located at the bottom face. See image on the following page.
R1
R2
Ultra Low Band
698-960 MHz Ports
Electrical Characteristics
R1-R2
Frequency Bands (MHz)
Gain (dBi)
(4x) 7/16-DIN Female Long Neck
Tilt 0°
Tilt 5°
Tilt 10°
700
800
900
15.5
15.5
15.2
16.5
16.4
16.2
17.4
17.3
17.0
Input Impedance
50Ω
VSWR
< 1.5
Polarisation
±45°
Horizontal Beamwidth (-3 dB)
75°
Vertical Beamwidth (-3 dB)
8.6°
68°
65°
7.5°
6.7°
Electrical Downtilt Range
0-10°
Inter/Intra Band Isolation
> 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back
Ratio
18 dB Typical
@ 180°
@ 180° ±30°
> 30 dB
> 25 dB
Maximum Power (Per Port)
250 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
40 | April 2015
(2x) 698-960 MHz
5920300
5920300A
5920300G
5920300DG
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
Mechanical Characteristics
Packaging
Dimensions (Height x Width x Depth)
2863 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
35 kg
Shroud
Outdoor Fibreglass, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 150 km/h
Frontal: 990 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 555 N
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
66 kg
Includes 0900181/00 Kit
Rear: 920 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
698-960 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 41
(2x) 790-960 MHz
5920200
5920200A
5920200G
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
• Twin 900 MHz antenna, dual polarisation, 4 connectors
• Independent tilt on each band 0-10°
LTE Ready
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0
• Single RET module to control both tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options
Model Number
Manual Electrical Tilt
5920200
Remote Electrical Tilt AISG1.1
5920200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5920200G
Access Ports Description (Connectors)
This antenna is built with two identical 900 MHz Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded
connectors located at the bottom face. See image on the following page.
RED Rings
Ultra Low Band Right
790-960 MHz Ports
(2x) 7/16-DIN Female Long Neck
GREEN Rings
Ultra Low Band Left
790-960 MHz Ports
(2x) 7/16-DIN Female Long Neck
Electrical Characteristics
RED or GREEN Ports
Frequency Bands (MHz)
Gain (dBi)
790...880...960 MHz
Tilt 0°
Tilt 5°
Tilt 10°
16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4
Input Impedance
50Ω
VSWR
< 1.4
Polarisation
±45°
Horizontal Beamwidth (-3 dB)
65° (±6°)
Vertical Beamwidth (-3 dB)
7.3°
Electrical Downtilt Range
0-10°
Intra Band Isolation
> 30 dB, > 28 dB from 0° to 2° tilt
Isolation Between Left & Right Arrays
> 30 dB
Upper Sidelobe Rejection
(20° sector above main beam)
18 dB Typical
Null Fill (First Null Below Main Beam)
< 20 dB
Front-to-Back Ratio
> 30 dB
Maximum Power (Per Port)
200 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET Module Part Number
(one per antenna)
MDCU-A0000
for AISG1.1 protocol (one unit included in 5920200A)
MDCU-G0000
for 3GPP/AISG2.0 protocol (one unit included in 5920200G)
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
42 | April 2015
(2x) 790-960 MHz
5920200
5920200A
5920200G
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
Mechanical Characteristics
Dimensions (Height x Width x Depth)
2700 x 442 x 152 mm
Weight (Excluding Mounting Accessories)
45 kg
Shroud
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 160 km/h
Frontal: 1300 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 220 N
Rear: 1700 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
Not available
---
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
790-960 MHz
GREEN
790-960 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 43
(2x) 790-960 MHz
5920200 lv
5920200A lv
(lightweight version)
5920200G lv
5920200DG lv
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
•
•
•
•
•
Twin 800-900 antenna, dual polarisation, 4 connectors
Independent tilt on each band 0-10°
Lightweight TwinLine platform
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
LTE Ready
EXTREMELY PROFILED - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5920200 lv
Remote Electrical Tilt AISG1.1
5920200A lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5920200G lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22)
5920200DG lv
Access Ports Description (Connectors)
This antenna is built with two identical Extended Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colourcoded connectors located at the bottom face. See image on the following page.
RED Rings
Extended Low Band
790-960 MHz Ports
GREEN Rings
Extended Low Band
790-960 MHz Ports
Electrical Characteristics
(2x) 7/16-DIN Female Long Neck
Low Band (RED or GREEN Ports)
Frequency Bands (MHz)
Gain (dBi)
(2x) 7/16-DIN Female Long Neck
790...880...960 MHz
Tilt 0°
Tilt 5°
Tilt 10°
16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4
Input Impedance
50Ω
VSWR
< 1.5
Polarisation
±45°
Horizontal Beamwidth (-3 dB)
73°...68°...63°
Vertical Beamwidth (-3 dB)
7.3°
Electrical Downtilt Range
0-10°
Inter/Intra Band Isolation
> 28 dB
Upper Sidelobe Rejection
(20° sector above main beam)
18 dB Typical
Front-to-Back Ratio
> 30 dB
Maximum Power (Per Port)
200 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control
RET-Ready
Unit (MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
44 | April 2015
(2x) 790-960 MHz
5920200 lv
5920200A lv
(lightweight version)
5920200G lv
5920200DG lv
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
Mechanical Characteristics
Packaging
Dimensions (Height x Width x Depth)
2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
51 kg
Includes 0900181/00 Kit
37 kg
Shroud
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 150 km/h (EN1991-4-1)
Frontal: 990 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 555 N
Rear: 920 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
1983
RED
790-960 MHz
GREEN
790-960 MHz
1865
153
432
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 45
(2x) 698-960 / 1695-2180 / 2490-2690 MHz
5978600
5978600A
5978600G
5978600DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 16.5 / 17.5 / 18.0 dBi | Variable Tilt
•
•
•
•
•
Twin tri band antenna, dual polarisation, 12 connectors
Independent tilt on each band 0-10° / 0-10° / 0-10°
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5978600
Remote Electrical Tilt AISG1.1
5978600A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5978600G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator
5978600DG
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
R1
R2
Ultra Low Band
698-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
B1
B2
Wide Band
1695-2180 MHz Ports
(4x) 7/16-DIN Female Long Neck
Y1
Y2
LTE 2600
2490-2690 MHz Ports
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)
Tilt 0°
Tilt 5°
Tilt 10°
R1-R2
B1-B2
Y1-Y2
700
800
900
1800
2100
2600
14.5
14.5
14.2
15.5
15.4
15.1
16.4
16.3
16.0
17.4
17.4
17.4
17.7
17.7
17.6
18.0
18.0
17.7
Input Impedance
50Ω
50Ω
50Ω
VSWR
< 1.5
< 1.5
< 1.5
Polarisation
±45°
±45°
±45°
Horizontal Beamwidth (-3 dB)
75°
68°
65°
65°
63°
61°
Vertical Beamwidth (-3 dB)
12°
10°
9.4°
6.1°
5.3°
4.2°
Electrical Downtilt Range
0-10°
0-10°
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from 0° to 2° tilt
> 30 dB
> 28 dB from
0° to 2° tilt
18 dB Typical
18 dB Typical
18 dB Typical
> 30 dB
> 25 dB
> 30 dB
> 25 dB
> 30 dB
> 25 dB
Maximum Power (Per Port)
250 W
200 W
200 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
< -110 dBm
Inter/Intra Band Isolation
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back
Ratio
0-10°
@ 180°
@ 180° ±30°
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator
(one per antenna)
Multi-Device Control
Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical
downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to
ordering options.
Multi-Device Dual Unit
(MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in
antennas with factory embedded motors (for antenna sharing or two technologies).
Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
46 | April 2015
(2x) 698-960 / 1695-2180 / 2490-2690 MHz
5978600
5978600A
5978600G
5978600DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 16.5 / 17.5 / 18.0 dBi | Variable Tilt
Environmental
Packaging
Operating Temperature Range
-40° C to +60° C
Environmental
Carton Box
2.15 x 0.55 x 0.28 m
0.33 m3
50 kg
Includes 0900181/00 Kit
ETS 300 019
RoHS Compliant
Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth)
1915 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
40 kg
Shroud
Outdoor Fibreglass, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 150 km/h
Frontal: 635 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 395 N
Rear: 656 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
698-960 MHz
BLUE
1695-2180 MHz
YELLOW
2490-2690 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 47
(2x) 698-960 / 1695-2690 MHz
5963300
5963300A
5963300G
5963300DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt
•
•
•
•
•
Twin dual band antenna, dual polarisation, 8 connectors
Independent tilt on each band 0-10° / 0-10°
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5963300
Remote Electrical Tilt AISG1.1
5963300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5963300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator
5963300DG
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.
R1
R2
Ultra Low Band
698-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
Y1
Y2
Ultra Wide Band
1695-2690 MHz Ports
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)
Tilt 0°
Tilt 5°
Tilt 10°
R1-R2
Y1-Y2
700
800
900
1800
2100
2600
14.5
14.5
14.2
15.5
15.4
15.1
16.4
16.3
16.0
17.7
17.7
17.7
18.1
18.1
18.0
18.5
18.5
18.2
Input Impedance
50Ω
50Ω
VSWR
< 1.5
< 1.5
Polarisation
±45°
±45°
Horizontal Beamwidth (-3 dB)
75°
68°
65°
65°
63°
61°
Vertical Beamwidth (-3 dB)
12°
10°
9.4°
6.1°
5.3°
4.2°
Electrical Downtilt Range
0-10°
0-10°
Inter/Intra Band Isolation
> 30 dB, > 28 dB from 0° to 2° tilt
> 30 dB, > 28 dB from 0° to 2° tilt
18 dB Typical
18 dB Typical
> 30 dB
> 25 dB
> 30 dB
> 25 dB
Maximum Power (Per Port)
250 W
200 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back
Ratio
@ 180°
@ 180° ±30°
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
48 | April 2015
(2x) 698-960 / 1695-2690 MHz
5963300
5963300A
5963300G
5963300DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt
Mechanical Characteristics
Packaging
Dimensions (Height x Width x Depth)
1915 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
33 kg
Shroud
Outdoor Fibreglass, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 150 km/h
Frontal: 635 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 395 N
Carton Box
2.15 x 0.55 x 0.28 m
0.33 m3
43 kg
Includes 0900181/00 Kit
Rear: 656 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
698-960 MHz
YELLOW
1695-2690 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 49
(2x) 790-960 / 1710-2170 MHz
5963200
5963200A
5963200G
5963200DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 68° / 68° | 16.5 / 18.1 dBi | Variable Tilt
•
•
•
•
•
Twin dual band antenna, dual polarisation, 8 connectors
Independent tilt on each band 0-10° / 0-10°
TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies
Ordering Options
Model Number
Manual Electrical Tilt
5963200
Remote Electrical Tilt AISG1.1
5963200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5963200G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12)
5963200DG
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.
RED | GREEN Rings
Low Band
790-960 MHz Ports
(4x) 7/16-DIN Female Long Neck
WHITE | BLUE Rings
High Band
1710-2170 MHz Ports
(4x) 7/16-DIN Female Long Neck
Electrical Characteristics
Low Band (RED or GREEN)
Frequency Bands (MHz)
Gain (dBi)
Tilt 0°
Tilt 5°
Tilt 10°
High Band (WHITE or BLUE)
790...880...960 MHz
1710...1880
1900...2170
15.5...16.0...16.5
15.5...16.0...16.5
15.4...15.9...16.4
17.3...17.6
17.2...17.4
17.2...17.3
17.6...18.1
17.4...17.9
17.3...17.7
Input Impedance
50Ω
50Ω
VSWR
< 1.5
< 1.5
Polarisation
±45°
±45°
Horizontal Beamwidth (-3 dB)
72°...68°...65°
65°
Vertical Beamwidth (-3 dB)
9°
6°
Electrical Downtilt Range
0-10°
0-10°
Intra Band Isolation
> 25 dB
> 28 dB
Isolation Between Bands
> 30 dB
> 30 dB
Isolation Between Left & Right Arrays
> 30 dB
> 30 dB
18 dB Typical
18 dB Typical
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back Ratio
64°
6°
> 30 dB
> 30 dB
Maximum Power (Per Port)
200 W
160 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control
RET-Ready
Unit (MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
50 | April 2015
(2x) 790-960 / 1710-2170 MHz
5963200
5963200A
5963200G
5963200DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 68° / 68° | 16.5 / 18.1 dBi | Variable Tilt
Mechanical Characteristics
Packaging
Dimensions (Height x Width x Depth)
1920 x 442 x 152 mm
Weight (Excluding Mounting Accessories)
Carton Box
2.23 x 0.55 x 0.28 m
0.343 m3 | 52 kg
41.5 kg
Shroud
Outdoor Plastic, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load
(EN1991-4-1)
Survival: 200 km/h
at 150 km/h
Frontal: 945 N
Lateral: 320 N
Rear: 886 N
at 160 km/h
Frontal: 1075 N
Lateral: 365 N
Rear: 1008 N
Mounting Kit Options
Part Number
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
790-960 MHz
GREEN
790-960 MHz
BLUE
1710-2170 MHz
WHITE
1710-2170 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 51
(2x) 698-960 MHz
5918300
5918300A
5918300G
5918300DG
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 16.5 dBi | Variable Tilt
•
•
•
•
•
Twin low band, dual polarisation, 4 connectors
Independent tilt on each band 0-10°
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
Ordering Options
Model Number
Manual Electrical Tilt
5918300
Remote Electrical Tilt AISG1.1
5918300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator
5918300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator
5918300DG
Access Ports Description (Connectors)
This antenna is built with two identical Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded
connectors located at the bottom face. See image on the following page.
R1
R2
Ultra Low Band
698-960 MHz Ports
Electrical Characteristics
R1-R2
Frequency Bands (MHz)
Gain (dBi)
(4x) 7/16-DIN Female Long Neck
Tilt 0°
Tilt 5°
Tilt 10°
700
800
900
14.5
14.5
14.2
15.5
15.4
15.1
16.4
16.3
16.0
Input Impedance
50Ω
VSWR
< 1.5
Polarisation
±45°
Horizontal Beamwidth (-3 dB)
75°
Vertical Beamwidth (-3 dB)
12°
68°
65°
10°
9.4°
Electrical Downtilt Range
0-10°
Inter/Intra Band Isolation
> 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection
(20° sector above main beam)
Front-to-Back
Ratio
18 dB Typical
@ 180°
@ 180° ±30°
> 30 dB
> 25 dB
Maximum Power (Per Port)
250 W
Intermodulation
3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET)
Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range
Environmental
RoHS Compliant
-40° C to +60° C
ETS 300 019
Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
52 | April 2015
(2x) 698-960 MHz
5918300
5918300A
5918300G
5918300DG
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 16.5 dBi | Variable Tilt
Mechanical Characteristics
Packaging
Dimensions (Height x Width x Depth)
1915 x 432 x 153 mm
Weight (Excluding Mounting Accessories)
24 kg
Shroud
Outdoor Fibreglass, Grey RAL7035
Wind Speed
Operational: 160 km/hr
Wind Load at 150 km/h
Frontal: 635 N
Mounting Kit Options
Part Number
Survival: 200 km/h
Lateral: 395 N
Carton Box
2.15 x 0.55 x 0.28 m
0.33 m3
34 kg
Includes 0900181/00 Kit
Rear: 656 N
Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm
0900181/00
3.4 kg
Brackets for pole 70 to 150 mm
0900182/00
3.9 kg
Kit to add mechanical tilt to above brackets
0900396/00
2.3 kg
Bottom View of Antenna
Dimensions (in mm)
Location of the MDCU or MDDU
for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
RED
698-960 MHz
Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
April 2015 | 53