Chapter 1 Introduction and Basic Concepts
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications
by Çengel & Cimbala
CHAPTER 1
INTRODUCTION AND BASIC CONCEPTS
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of The McGraw-Hill Companies, Inc.
(“McGraw-Hill”) and protected by copyright and other state and federal laws. By
opening and using this Manual the user agrees to the following restrictions, and if the
recipient does not agree to these restrictions, the Manual should be promptly returned
unopened to McGraw-Hill: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated
textbook. No other use or distribution of this Manual is permitted. This Manual
may not be sold and may not be distributed to or used by any student or other
third party. No part of this Manual may be reproduced, displayed or distributed
in any form or by any means, electronic or otherwise, without the prior written
permission of McGraw-Hill.
1-1
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
Introduction, Classification, and System
1-1C
Solution
We are to define internal, external, and open-channel flows.
Analysis
External flow is the flow of an unbounded fluid over a surface such as a plate, a wire, or a pipe. The flow
in a pipe or duct is internal flow if the fluid is completely bounded by solid surfaces. The flow of liquids in a pipe is
called open-channel flow if the pipe is partially filled with the liquid and there is a free surface, such as the flow of
water in rivers and irrigation ditches.
Discussion
As we shall see in later chapters, there different approximations are used in the analysis of fluid flows based
on their classification.
1-2C
Solution
We are to define incompressible and compressible flow, and discuss fluid compressibility.
Analysis
A fluid flow during which the density of the fluid remains nearly constant is called incompressible flow.
A flow in which density varies significantly is called compressible flow. A fluid whose density is practically independent
of pressure (such as a liquid) is commonly referred to as an “incompressible fluid,” although it is more proper to refer to
incompressible flow. The flow of compressible fluid (such as air) does not necessarily need to be treated as compressible
since the density of a compressible fluid may still remain nearly constant during flow – especially flow at low speeds.
Discussion
It turns out that the Mach number is the critical parameter to determine whether the flow of a gas can be
approximated as an incompressible flow. If Ma is less than about 0.3, the incompressible approximation yields results that
are in error by less than a couple percent.
1-3C
Solution
We are to define the no-slip condition and its cause.
Analysis
A fluid in direct contact with a solid surface sticks to the surface and there is no slip. This is known as
the no-slip condition, and it is due to the viscosity of the fluid.
Discussion
There is no such thing as an inviscid fluid, since all fluids have viscosity.
1-4C
Solution
We are to define forced flow and discuss the difference between forced and natural flow. We are also to
discuss whether wind-driven flows are forced or natural.
Analysis
In forced flow, the fluid is forced to flow over a surface or in a tube by external means such as a pump or a
fan. In natural flow, any fluid motion is caused by natural means such as the buoyancy effect that manifests itself as the rise
of the warmer fluid and the fall of the cooler fluid. The flow caused by winds is natural flow for the earth, but it is
forced flow for bodies subjected to the winds since for the body it makes no difference whether the air motion is caused
by a fan or by the winds.
Discussion
As seen here, the classification of forced vs. natural flow may depend on your frame of reference.
1-2
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
1-5C
Solution
We are to define a boundary layer, and discuss its cause.
Analysis
When a fluid stream encounters a solid surface that is at rest, the fluid velocity assumes a value of zero at
that surface. The velocity then varies from zero at the surface to the freestream value sufficiently far from the surface. The
region of flow in which the velocity gradients are significant and frictional effects are important is called the
boundary layer. The development of a boundary layer is caused by the no-slip condition.
Discussion
As we shall see later, flow within a boundary layer is rotational (individual fluid particles rotate), while that
outside the boundary layer is typically irrotational (individual fluid particles move, but do not rotate).
1-6C
Solution
We are to discuss the differences between classical and statistical approaches.
Analysis
The classical approach is a macroscopic approach, based on experiments or analysis of the gross behavior
of a fluid, without knowledge of individual molecules, whereas the statistical approach is a microscopic approach based
on the average behavior of large groups of individual molecules.
Discussion
The classical approach is easier and much more common in fluid flow analysis.
1-7C
Solution
We are to define a steady-flow process.
Analysis
A process is said to be steady if it involves no changes with time anywhere within the system or at the
system boundaries.
Discussion
The opposite of steady flow is unsteady flow, which involves changes with time.
1-8C
Solution
We are to define stress, normal stress, shear stress, and pressure.
Analysis
Stress is defined as force per unit area, and is determined by dividing the force by the area upon which it
acts. The normal component of a force acting on a surface per unit area is called the normal stress, and the tangential
component of a force acting on a surface per unit area is called shear stress. In a fluid at rest, the normal stress is called
pressure.
Discussion
the pressure.
1-9C
Solution
Fluids in motion may have additional normal stresses, but when a fluid is at rest, the only normal stress is
We are to define system, surroundings, and boundary.
Analysis
A system is defined as a quantity of matter or a region in space chosen for study. The mass or region
outside the system is called the surroundings. The real or imaginary surface that separates the system from its
surroundings is called the boundary.
Discussion
Some authors like to define closed systems and open systems, while others use the notation “system” to
mean a closed system and “control volume” to mean an open system. This has been a source of confusion for students for
many years. [See the next question for further discussion about this.]
1-3
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
1-10C
Solution
We are to discuss when a system is considered closed or open.
Analysis
Systems may be considered to be closed or open, depending on whether a fixed mass or a volume in space
is chosen for study. A closed system (also known as a control mass or simply a system) consists of a fixed amount of
mass, and no mass can cross its boundary. An open system, or a control volume, is a properly selected region in space.
Discussion
In thermodynamics, it is more common to use the terms open system and closed system, but in fluid
mechanics, it is more common to use the terms system and control volume to mean the same things, respectively.
Mass, Force, and Units
1-11C
Solution
We are to discuss the difference between pound-mass and pound-force.
Analysis
Pound-mass lbm is the mass unit in English system whereas pound-force lbf is the force unit in the
English system. One pound-force is the force required to accelerate a mass of 32.174 lbm by 1 ft/s2. In other words, the
weight of a 1-lbm mass at sea level on earth is 1 lbf.
Discussion
It is not proper to say that one lbm is equal to one lbf since the two units have different dimensions.
1-12C
Solution
We are to discuss the difference between kg-mass and kg-force.
Analysis
The unit kilogram (kg) is the mass unit in the SI system, and it is sometimes called kg-mass, whereas kgforce (kgf) is a force unit. One kg-force is the force required to accelerate a 1-kg mass by 9.807 m/s2. In other words, the
weight of 1-kg mass at sea level on earth is 1 kg-force.
Discussion
dimensions.
It is not proper to say that one kg-mass is equal to one kg-force since the two units have different
1-13C
Solution
We are to calculate the net force on a car cruising at constant velocity.
Analysis
There is no acceleration, thus the net force is zero in both cases.
Discussion
By Newton’s second law, the force on an object is directly proportional to its acceleration. If there is zero
acceleration, there must be zero net force.
1-4
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
1-14
Solution
A plastic tank is filled with water. The weight of the combined system is to be determined.
Assumptions
The density of water is constant throughout.
Properties
The density of water is given to be ρ = 1000 kg/m3.
Analysis
The mass of the water in the tank and the total mass are
mtank=3 kg
V = 0.2
mw =ρV =(1000 kg/m3)(0.2 m3) = 200 kg
mtotal = mw + mtank = 200 + 3 = 203 kg
m
3
Thus,
⎛ 1 N
⎞
W = mg = (203 kg)(9.81 m/s 2 ) ⎜
= 1991 N ≅ 1990 N
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
where we give the final answer to three significant digits.
Discussion
Note the unity conversion factor in the above equation.
1-15
Solution
determined.
The interior dimensions of a room are given. The mass and weight of the air in the room are to be
Assumptions
The density of air is constant throughout the room.
Properties
The density of air is given to be ρ = 1.16 kg/m3.
Analysis
The mass of the air in the room is
m = ρV = (1.16 kg/m3 )(6 × 6 × 8 m3 ) = 334.1 kg ≅ 334 kg
ROOM
AIR
6X6X8 m
3
Thus,
⎛ 1 N
⎞
W = mg = (334.1 kg)(9.81 m/s 2 ) ⎜
= 3277 N ≅ 3280 N
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
Discussion
Note that we round our final answers to three significant digits, but use extra digit(s) in intermediate
calculations. Considering that the mass of an average man is about 70 to 90 kg, the mass of air in the room is probably
larger than you might have expected.
1-16
Solution
The variation of gravitational acceleration above sea level is given as a function of altitude. The height at
which the weight of a body decreases by 1% is to be determined.
z
Analysis
The weight of a body at the elevation z can be expressed as
W = mg = m(9.807 − 3.32 × 10−6 z)
In our case,
W = 0.99Ws = 0.99mgs = 0.99(m)(9.807)
Substituting,
0.99 ( 9.807 ) = ( 9.807 − 3.32 × 10 −6 z ) ⎯⎯
→ z = 29 ,540 m ≅ 29,500 m
where we have rounded off the final answer to three significant digits.
0
Sea level
Discussion
This is more than three times higher than the altitude at which a typical commercial jet flies, which is about
30,000 ft (9140 m). So, flying in a jet is not a good way to lose weight – diet and exercise are always the best bet.
1-5
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
1-17E
Solution
An astronaut takes his scales with him to the moon. It is to be determined how much he weighs on the
spring and beam scales on the moon.
Analysis
(a) A spring scale measures weight, which is the local gravitational force applied on a body:
⎛
1 lbf
W = mg = (150 lbm)(5.48 ft/s 2 )⎜
⎜ 32.2 lbm ⋅ ft/s 2
⎝
⎞
⎟ = 25.5 lbf
⎟
⎠
(b) A beam scale compares masses and thus is not affected by the variations in gravitational acceleration. The beam scale
reads what it reads on earth,
W = 150 lbf
Discussion
The beam scale may be marked in units of weight (lbf), but it really compares mass, not weight. Which
scale would you consider to be more accurate?
1-18
Solution
determined.
The acceleration of an aircraft is given in g’s. The net upward force acting on a man in the aircraft is to be
Analysis
From Newton's second law, the applied force is
⎛ 1 N
⎞
F = ma = m( 6 g ) = (90 kg)(6 × 9.81 m/s 2 ) ⎜
= 5297 N ≅ 5300 N
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
where we have rounded off the final answer to three significant digits.
Discussion
The man feels like he is six times heavier than normal. You get a similar feeling when riding an elevator to
the top of a tall building, although to a much lesser extent.
1-19 [Also solved by EES on enclosed CD]
Solution
A rock is thrown upward with a specified force. The acceleration of the rock is to be determined.
The weight of the rock is
Analysis
⎛ 1 N
W = mg = (5 kg)(9.79 m/s 2 ) ⎜
2
⎝ 1 kg ⋅ m/s
⎞
⎟ = 48.95 N ≅ 49.0 N
⎠
Then the net force that acts on the rock is
Fnet = Fup − Fdown = 150 − 48.95 = 101.05 N
From Newton's second law, the acceleration of the rock becomes
a=
Discussion
F 101.05 N ⎛⎜ 1 kg ⋅ m/s 2
=
5 kg ⎜⎝
1N
m
Rock
⎞
⎟ = 20.2 m/s 2
⎟
⎠
This acceleration is more than twice the acceleration at which it would fall (due to gravity) if dropped.
1-6
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
1-20
Solution
The previous problem is recalculated using EES. The entire EES solution is to be printed out, including the
numerical results with proper units.
Analysis
The EES Equations window is printed below, followed by the Solution window.
W=m*g"[N]"
m=5"[kg]"
g=9.79"[m/s^2]"
"The force balance on the rock yields the net force acting on the rock as"
F_net = F_up - F_down"[N]"
F_up=150"[N]"
F_down=W"[N]"
"The acceleration of the rock is determined from Newton's second law."
F_net=a*m
"To Run the program, press F2 or click on the calculator icon from the Calculate menu"
SOLUTION
Variables in Main
a=20.21 [m/s^2]
F_down=48.95 [N]
F_net=101.1 [N]
F_up=150 [N]
g=9.79 [m/s^2]
m=5 [kg]
W=48.95 [N]
The final results are W = 49.0 N and a = 20.2 m/s2, to three significant digits, which agree with the results of the previous
problem.
Discussion
Items in quotation marks in the EES Equation window are comments. Units are in square brackets.
1-21
Solution
Gravitational acceleration g and thus the weight of bodies decreases with increasing elevation. The percent
reduction in the weight of an airplane cruising at 13,000 m is to be determined.
Properties
The gravitational acceleration g is 9.807 m/s2 at sea level and 9.767 m/s2 at an altitude of 13,000 m.
Analysis
Weight is proportional to the gravitational acceleration g, and thus the percent reduction in weight is
equivalent to the percent reduction in the gravitational acceleration, which is determined from
Δg
9.807 − 9.767
× 100 =
× 100 = 0.41%
g
9.807
Therefore, the airplane and the people in it will weigh 0.41% less at 13,000 m altitude.
% Reduction in weight = % Reduction in g =
Discussion
Note that the weight loss at cruising altitudes is negligible. Sorry, but flying in an airplane is not a good
way to lose weight. The best way to lose weight is to carefully control your diet, and to exercise.
1-7
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
Modeling and Solving Problems, and Precision
1-22C
Solution
We are to discuss the difference between accuracy and precision.
Analysis
Accuracy refers to the closeness of the measured or calculated value to the true value whereas precision
represents the number of significant digits or the closeness of different measurements of the same quantity to each
other. A measurement or calculation can be very precise without being very accurate, and vice-versa. When
measuring the boiling temperature of pure water at standard atmospheric conditions, for example, a temperature
measurement of 97.861°C is very precise, but not as accurate as the less precise measurement of 99.0°C.
Discussion
Accuracy and precision are often confused; both are important for quality engineering measurements.
1-23C
Solution
We are to discuss the difference between analytical and experimental approaches.
Analysis
The experimental approach (testing and taking measurements) has the advantage of dealing with the
actual physical system, and getting a physical value within the limits of experimental error. However, this approach is
expensive, time consuming, and often impractical. The analytical approach (analysis or calculations) has the advantage
that it is fast and inexpensive, but the results obtained are subject to the accuracy of the assumptions and idealizations made
in the analysis.
Discussion
Most engineering designs require both analytical and experimental components, and both are important.
Nowadays, computational fluid dynamics (CFD) is often used in place of pencil-and-paper analysis and/or experiments.
1-24C
Solution
We are to discuss the importance of modeling in engineering.
Analysis
Modeling makes it possible to predict the course of an event before it actually occurs, or to study
various aspects of an event mathematically without actually running expensive and time-consuming experiments.
When preparing a mathematical model, all the variables that affect the phenomena are identified, reasonable assumptions
and approximations are made, and the interdependence of these variables are studied. The relevant physical laws and
principles are invoked, and the problem is formulated mathematically. Finally, the problem is solved using an appropriate
approach, and the results are interpreted.
Discussion
In most cases of actual engineering design, the results are verified by experiment – usually by building a
prototype. CFD is also being used more and more in the design process.
1-25C
Solution
We are to discuss choosing a model.
Analysis
The right choice between a crude and complex model is usually the simplest model that yields adequate
results. Preparing very accurate but complex models is not necessarily a better choice since such models are not much use
to an analyst if they are very difficult and time consuming to solve. At a minimum, the model should reflect the essential
features of the physical problem it represents.
Discussion
Cost is always an issue in engineering design, and “adequate” is often determined by cost.
1-8
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
1-26C
Solution
We are to discuss how differential equations arise in the study of a physical problem.
Analysis
The description of most scientific problems involves equations that relate the changes in some key
variables to each other, and the smaller the increment chosen in the changing variables, the more accurate the description.
In the limiting case of infinitesimal changes in variables, we obtain differential equations, which provide precise
mathematical formulations for the physical principles and laws by representing the rates of changes as derivatives.
Discussion
As we shall see in later chapters, the differential equations of fluid mechanics are known, but very difficult
to solve except for very simple geometries. Computers are extremely helpful in this area.
1-27C
Solution
We are to discuss the value of engineering software packages.
Analysis
Software packages are of great value in engineering practice, and engineers today rely on software
packages to solve large and complex problems quickly, and to perform optimization studies efficiently. Despite the
convenience and capability that engineering software packages offer, they are still just tools, and they cannot replace
traditional engineering courses. They simply cause a shift in emphasis in the course material from mathematics to physics.
Discussion
While software packages save us time by reducing the amount of number-crunching, we must be careful to
understand how they work and what they are doing, or else incorrect results can occur.
1-28
Solution
We are to determine a positive real root of the following equation using EES: 2x3 – 10x0.5 – 3x = -3.
Analysis
Using EES software, copy the following lines and paste on a blank EES screen to verify the solution:
2*x^3-10*x^0.5-3*x = -3
Answer:
x = 2.063 (using an initial guess of x = 2)
Discussion
To obtain the solution in EES, click on the icon that looks like a calculator, or Calculate-Solve.
1-29
Solution
We are to solve a system of 2 equations and 2 unknowns using EES.
Analysis
Using EES software, copy the following lines and paste on a blank EES screen to verify the solution:
x^3-y^2=7.75
3*x*y+y=3.5
Answers:
x = 2.0, y = 0.50.
Discussion
To obtain the solution in EES, click on the icon that looks like a calculator, or Calculate-Solve.
1-9
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
1-30
Solution
We are to solve a system of 3 equations with 3 unknowns using EES.
Analysis
Using EES software, copy the following lines and paste on a blank EES screen to verify the solution:
2*x-y+z=5
3*x^2+2*y=z+2
x*y+2*z=8
Answers: x = 1.141, y = 0.8159, z = 3.535.
Discussion
To obtain the solution in EES, click on the icon that looks like a calculator, or Calculate-Solve.
1-31
Solution
We are to solve a system of 3 equations with 3 unknowns using EES.
Analysis
Using EES software, copy the following lines and paste on a blank EES screen to verify the solution:
x^2*y-z=1
x-3*y^0.5+x*z=-2
x+y-z=2
Answers: x = 1, y = 1, z = 0.
Discussion
To obtain the solution in EES, click on the icon that looks like a calculator, or Calculate-Solve.
Review Problems
1-32
Solution
The gravitational acceleration changes with altitude. Accounting for this variation, the weights of a body at
different locations are to be determined.
Analysis
the relation
The weight of an 80-kg man at various locations is obtained by substituting the altitude z (values in m) into
⎛
1N
W = mg = (80 kg)(9.807 − 3.32 × 10 − 6 z m/s 2 )⎜
⎜ 1 kg ⋅ m/s 2
⎝
Sea level:
Denver:
Mt. Ev.:
⎞
⎟
⎟
⎠
(z = 0 m): W = 80×(9.807-3.32x10-6×0) = 80×9.807 = 784.6 N
(z = 1610 m): W = 80×(9.807-3.32x10-6×1610) = 80×9.802 = 784.2 N
(z = 8848 m): W = 80×(9.807-3.32x10-6×8848) = 80×9.778 = 782.2 N
Discussion
We report 4 significant digits since the values are so close to each other. The percentage difference in
weight from sea level to Mt. Everest is only about -0.3%, which is negligible for most engineering calculations.
1-10
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 1 Introduction and Basic Concepts
1-33
Solution
A man is considering buying a 12-oz steak for $3.15, or a 320-g steak for $2.80. The steak that is a better
buy is to be determined.
Assumptions
The steaks are of identical quality.
Analysis
To make a comparison possible, we need to express the cost of each steak on a common basis. We choose 1
kg as the basis for comparison. Using proper conversion factors, the unit cost of each steak is determined to be
⎛ $3.15 ⎞ ⎛ 16 oz ⎞ ⎛ 1 lbm ⎞
⎟⎟ = $9.26/kg
Unit Cost = ⎜
⎟⎜
⎟ ⎜⎜
⎝ 12 oz ⎠ ⎝ 1 lbm ⎠ ⎝ 0.45359 kg ⎠
12 ounce steak:
320 gram steak:
⎛ $2.80 ⎞ ⎛ 1000 g ⎞
⎟⎟ = $8.75/kg
⎟⎟ ⎜⎜
Unit Cost = ⎜⎜
⎝ 320 g ⎠ ⎝ 1 kg ⎠
Therefore, the steak at the international market is a better buy.
Discussion
Notice the unity conversion factors in the above equations.
1-34
Solution
The thrust developed by the jet engine of a Boeing 777 is given to be
85,000 pounds. This thrust is to be expressed in N and kgf.
Analysis
Noting that 1 lbf = 4.448 N and 1 kgf = 9.81 N, the thrust developed is
expressed in two other units as
Thrust in N:
Thrust in kgf:
4.448 N ⎞
5
Thrust = (85,000 lbf )⎛⎜
⎟ = 3.78 × 10 N
⎝ 1 lbf ⎠
⎛ 1 kgf ⎞
4
Thrust = (37.8 × 10 5 N )⎜
⎟ = 3.85 × 10 kgf
⎝ 9.81 N ⎠
Discussion
Because the gravitational acceleration on earth is close to 10 m/s2, it turns out that the two force units N and
kgf differ by nearly a factor of 10. This can lead to confusion, and we recommend that you do not use the unit kgf.
Design and Essay Problem
1-35
Solution
We are to write an essay on mass- and volume-measurement devices.
Discussion
Students’ essays should be unique and will differ from each other.
KJ
1-11
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications
by Çengel & Cimbala
CHAPTER 2
PROPERTIES OF FLUIDS
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of The McGraw-Hill Companies, Inc.
(“McGraw-Hill”) and protected by copyright and other state and federal laws. By
opening and using this Manual the user agrees to the following restrictions, and if the
recipient does not agree to these restrictions, the Manual should be promptly returned
unopened to McGraw-Hill: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated
textbook. No other use or distribution of this Manual is permitted. This Manual
may not be sold and may not be distributed to or used by any student or other
third party. No part of this Manual may be reproduced, displayed or distributed
in any form or by any means, electronic or otherwise, without the prior written
permission of McGraw-Hill.
2-1
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
Density and Specific Gravity
2-1C
Solution
We are to discuss the difference between intensive and extensive properties.
Analysis
Intensive properties do not depend on the size (extent) of the system but extensive properties do depend
on the size (extent) of the system.
Discussion
An example of an intensive property is temperature. An example of an extensive property is mass.
2-2C
Solution
We are to define specific gravity and discuss its relationship to density.
Analysis
The specific gravity, or relative density, is defined as the ratio of the density of a substance to the density
of some standard substance at a specified temperature (the standard is water at 4°C, for which ρH2O = 1000 kg/m3). That
is, SG = ρ / ρ H2O . When specific gravity is known, density is determined from ρ = SG × ρ H2O .
Discussion
Specific gravity is dimensionless and unitless [it is just a number without dimensions or units].
2-3C
Solution
We are to discuss the applicability of the ideal gas law.
Analysis
A gas can be treated as an ideal gas when it is at a high temperature and/or a low pressure relative to its
critical temperature and pressure.
Discussion
Air and many other gases at room temperature and pressure can be approximated as ideal gases without any
significant loss of accuracy.
2-4C
Solution
We are to discuss the difference between R and Ru.
Analysis
Ru is the universal gas constant that is the same for all gases, whereas R is the specific gas constant that is
different for different gases. These two are related to each other by R = Ru / M , where M is the molar mass (also called
the molecular weight) of the gas.
Discussion
Since molar mass has dimensions of mass per mole, R and Ru do not have the same dimensions or units.
2-2
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-5
Solution
A balloon is filled with helium gas. The number of moles and the mass of helium are to be determined.
Assumptions
At specified conditions, helium behaves as an ideal gas.
Properties
The universal gas constant is Ru = 8.314 kPa.m3/kmol.K. The molar mass of helium is 4.0 kg/kmol.
Analysis
The volume of the sphere is
V =
4 3 4
π r = π (3 m) 3 = 113.1 m 3
3
3
Assuming ideal gas behavior, the number of moles of He is determined from
N=
He
D=6m
20°C
200 kPa
3
(200 kPa)(113.1 m )
PV
=
= 9.286 kmol
Ru T (8.314 kPa ⋅ m 3 /kmol ⋅ K)(293 K)
Then the mass of He is determined from
m = NM = (9.286 kmol)(4.0 kg/kmol) = 37.1 kg
Discussion
Although the helium mass may seem large (about half the mass of an adult man!), it is much smaller than
that of the air it displaces, and that is why helium balloons rise in the air.
2-6
Solution
A balloon is filled with helium gas. The effect of the balloon diameter on the mass of helium is to be
investigated, and the results are to be tabulated and plotted.
The EES Equations window is shown below, followed by the Solution window and the parametric table.
Analysis
"Given Data"
{D=6"[m]"}
{P=200"[kPa]"}
T=20"[C]"
P=100"[kPa]"
R_u=8.314"[kJ/kmol*K]"
"Solution"
P*V=N*R_u*(T+273)
V=4*pi*(D/2)^3/3"[m^3]"
m=N*MOLARMASS(Helium)"[kg]"
D [m]
0.5
2.111
3.722
5.333
6.944
8.556
10.17
11.78
13.39
15
Discussion
m [kg]
0.01075
0.8095
4.437
13.05
28.81
53.88
90.41
140.6
206.5
290.4
500
P = 200 kPa
P = 100 kPa
400
m [kg]
300
200
100
0
0
2
4
6
8
10
12
14
D [m]
Mass of Helium in Balloon as function of Diameter
Mass increases with diameter as expected, but not linearly since volume is proportional to D3.
2-3
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-7
Solution
An automobile tire is inflated with air. The pressure rise of air in the tire when the tire is heated and the
amount of air that must be bled off to reduce the temperature to the original value are to be determined.
Assumptions
1 At specified conditions, air behaves as an ideal gas. 2 The volume of the tire remains constant.
Properties
The gas constant of air is R = 0.287 kPa⋅m3/kg⋅K.
Analysis
Initially, the absolute pressure in the tire is
P1 = Pg + Patm = 210 + 100 = 310 kPa
Treating air as an ideal gas and assuming the volume of the tire to remain
constant, the final pressure in the tire is determined from
323K
P1V1 P2V 2
T
(310kPa) = 336 kPa
=
⎯
⎯→ P2 = 2 P1 =
298K
T1
T2
T1
Tire
25°C
Thus the pressure rise is
ΔP = P2 − P1 = 336 − 310 = 26.0 kPa
210 kPa
The amount of air that needs to be bled off to restore pressure to its original value is
m1 =
m2 =
Discussion
P1V
(310kPa)(0.025m 3 )
=
= 0.0906kg
RT1 (0.287kPa ⋅ m 3 /kg ⋅ K)(298K)
P2V
(310kPa)(0.025m 3 )
=
= 0.0836kg
RT2 (0.287kPa ⋅ m 3 /kg ⋅ K)(323K)
Δm = m1 − m 2 = 0.0906 − 0.0836 = 0.0070 kg
Notice that absolute rather than gage pressure must be used in calculations with the ideal gas law.
2-8E
Solution
An automobile tire is under-inflated with air. The amount of air that needs to be added to the tire to raise its
pressure to the recommended value is to be determined.
Assumptions
1 At specified conditions, air behaves as an ideal gas. 2 The volume of the tire remains constant.
Properties
The gas constant of air is R = 0.3704 psia⋅ft3/lbm⋅R.
Analysis
The initial and final absolute pressures in the tire are
P1 = Pg1 + Patm = 20 + 14.6 = 34.6 psia
P2 = Pg2 + Patm = 30 + 14.6 = 44.6 psia
Tire
0.53 ft3
90°F
20 psia
Treating air as an ideal gas, the initial mass in the tire is
(34.6 psia)(0.53 ft 3 )
PV
m1 = 1 =
= 0.0900 lbm
RT1 (0.3704 psia ⋅ ft 3 /lbm ⋅ R)(550 R)
Noting that the temperature and the volume of the tire remain constant, the final mass in the tire becomes
(44.6 psia)(0.53 ft 3 )
PV
m2 = 2 =
= 0.1160 lbm
RT2 (0.3704 psia ⋅ ft 3 /lbm ⋅ R)(550 R)
Thus the amount of air that needs to be added is Δm = m2 − m1 = 0.1160 − 0.0900 = 0.0260 lbm
Discussion
Notice that absolute rather than gage pressure must be used in calculations with the ideal gas law.
2-4
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-9E
Solution
A rigid tank contains slightly pressurized air. The amount of air that needs to be added to the tank to raise
its pressure and temperature to the recommended values is to be determined.
Assumptions
1 At specified conditions, air behaves as an ideal gas. 2 The volume of the tank remains constant.
Properties
The gas constant of air is R = 0.3704 psia⋅ft3/lbm⋅R.
Analysis
Treating air as an ideal gas, the initial volume and the final mass in the tank are determined to be
V =
m2 =
3
m1 RT1 (20 lbm)(0.3704 psia ⋅ ft /lbm ⋅ R)(530 R)
=
= 196.3 ft 3
P1
20 psia
(35 psia)(196.3 ft 3 )
P2V
=
= 33.73 lbm
RT2 (0.3704 psia ⋅ ft 3 /lbm ⋅ R)(550 R)
Air, 20 lbm
20 psia
70°F
Thus the amount of air added is
Δm = m2 − m1 = 33.73 − 20.0 = 13.7 lbm
Discussion
As the temperature slowly decreases due to heat transfer, the pressure will also decrease.
2-5
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-10
Solution
A relation for the variation of density with elevation is to be obtained, the density at 7 km elevation is to be
calculated, and the mass of the atmosphere using the correlation is to be estimated.
Assumptions 1 Atmospheric air behaves as an ideal gas. 2 The earth is perfectly spherical with a radius of 6377 km at sea
level, and the thickness of the atmosphere is 25 km.
The density data are given in tabular form as a function of radius and elevation, where r = z + 6377 km:
ρ, kg/m3
1.225
1.112
1.007
0.9093
0.8194
0.7364
0.6601
0.5258
0.4135
0.1948
0.08891
0.04008
1.4
1.2
1
3
z, km
0
1
2
3
4
5
6
8
10
15
20
25
r, km
6377
6378
6379
6380
6381
6382
6383
6385
6387
6392
6397
6402
ρ, kg/m
Properties
0.8
0.6
0.4
0.2
0
0
5
10
15
20
25
z, km
Analysis
Using EES, (1) Define a trivial function “rho= a+z” in the Equation window, (2) select new parametric table
from Tables, and type the data in a two-column table, (3) select Plot and plot the data, and (4) select Plot and click on curve
fit to get curve fit window. Then specify 2nd order polynomial and enter/edit equation. The results are:
ρ(z) = a + bz + cz2 = 1.20252 – 0.101674z + 0.0022375z2 for the unit of kg/m3,
(or, ρ(z) = (1.20252 – 0.101674z + 0.0022375z2)×109 for the unit of kg/km3)
where z is the vertical distance from the earth surface at sea level. At z = 7 km, the equation gives ρ = 0.600 kg/m3.
(b) The mass of atmosphere is evaluated by integration to be
m=
∫
V
ρdV =
∫
h
z =0
(a + bz + cz 2 )4π (r0 + z ) 2 dz = 4π
∫
h
z =0
(a + bz + cz 2 )(r02 + 2r0 z + z 2 )dz
[
]
= 4π ar02 h + r0 (2a + br0 )h 2 / 2 + (a + 2br0 + cr02 )h 3 / 3 + (b + 2cr0 )h 4 / 4 + ch 5 / 5
where r0 = 6377 km is the radius of the earth, h = 25 km is the thickness of the atmosphere. Also, a = 1.20252,
b = -0.101674, and c = 0.0022375 are the constants in the density function. Substituting and multiplying by the factor 109 to
convert the density from units of kg/km3 to kg/m3, the mass of the atmosphere is determined to be approximately
m = 5.09×1018 kg
EES Solution for final result:
a=1.2025166
b=-0.10167
c=0.0022375
r=6377
h=25
m=4*pi*(a*r^2*h+r*(2*a+b*r)*h^2/2+(a+2*b*r+c*r^2)*h^3/3+(b+2*c*r)*h^4/4+c*h^5/5)*1E+9
Discussion
At 7 km, the density of the air is approximately half of its value at sea level.
2-6
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
Vapor Pressure and Cavitation
2-11C
Solution
We are to define vapor pressure and discuss its relationship to saturation pressure.
Analysis
The vapor pressure Pv of a pure substance is defined as the pressure exerted by a vapor in phase
equilibrium with its liquid at a given temperature. In general, the pressure of a vapor or gas, whether it exists alone or in
a mixture with other gases, is called the partial pressure. During phase change processes between the liquid and vapor
phases of a pure substance, the saturation pressure and the vapor pressure are equivalent since the vapor is pure.
Discussion
Partial pressure is not necessarily equal to vapor pressure. For example, on a dry day (low relative
humidity), the partial pressure of water vapor in the air is less than the vapor pressure of water. If, however, the relative
humidity is 100%, the partial pressure and the vapor pressure are equal.
2-12C
Solution
We are to discuss whether the boiling temperature of water increases as pressure increases.
Analysis
Yes. The saturation temperature of a pure substance depends on pressure; in fact, it increases with pressure.
The higher the pressure, the higher the saturation or boiling temperature.
Discussion
This fact is easily seen by looking at the saturated water property tables. Note that boiling temperature and
saturation pressure at a given pressure are equivalent.
2-13C
Solution
increases.
We are to determine if temperature increases or remains constant when the pressure of a boiling substance
Analysis
If the pressure of a substance increases during a boiling process, the temperature also increases since the
boiling (or saturation) temperature of a pure substance depends on pressure and increases with it.
Discussion
We are assuming that the liquid will continue to boil. If the pressure is increased fast enough, boiling may
stop until the temperature has time to reach its new (higher) boiling temperature. A pressure cooker uses this principle.
2-14C
Solution
We are to define and discuss cavitation.
Analysis
In the flow of a liquid, cavitation is the vaporization that may occur at locations where the pressure
drops below the vapor pressure. The vapor bubbles collapse as they are swept away from the low pressure regions,
generating highly destructive, extremely high-pressure waves. This phenomenon is a common cause for drop in
performance and even the erosion of impeller blades.
Discussion
The word “cavitation” comes from the fact that a vapor bubble or “cavity” appears in the liquid. Not all
cavitation is undesirable. It turns out that some underwater vehicles employ “super cavitation” on purpose to reduce drag.
2-7
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-15
Solution
The minimum pressure in a piping system to avoid cavitation is to be determined.
Properties
The vapor pressure of water at 40°C is 7.38 kPa.
Analysis
To avoid cavitation, the pressure anywhere in the flow should not be allowed to drop below the vapor (or
saturation) pressure at the given temperature. That is,
Pmin = Psat @ 40°C = 7.38 kPa
Therefore, the pressure should be maintained above 7.38 kPa everywhere in flow.
Discussion
Note that the vapor pressure increases with increasing temperature, and thus the risk of cavitation is greater
at higher fluid temperatures.
2-16
Solution
The minimum pressure in a pump is given. It is to be determined if there is a danger of cavitation.
Properties
The vapor pressure of water at 20°C is 2.339 kPa.
Analysis
To avoid cavitation, the pressure everywhere in the flow should remain above the vapor (or saturation)
pressure at the given temperature, which is
Pv = Psat @ 20°C = 2.339 kPa
The minimum pressure in the pump is 2 kPa, which is less than the vapor pressure. Therefore, a there is danger of
cavitation in the pump.
Discussion
Note that the vapor pressure increases with increasing temperature, and thus there is a greater danger of
cavitation at higher fluid temperatures.
2-17E
Solution
The minimum pressure in a pump is given. It is to be determined if there is a danger of cavitation.
Properties
The vapor pressure of water at 70°F is 0.3632 psia.
Analysis
To avoid cavitation, the pressure everywhere in the flow should remain above the vapor (or saturation)
pressure at the given temperature, which is
Pv = Psat @ 70° F = 0.3632 psia
The minimum pressure in the pump is 0.1 psia, which is less than the vapor pressure. Therefore, there is danger of
cavitation in the pump.
Discussion
Note that the vapor pressure increases with increasing temperature, and the danger of cavitation increases at
higher fluid temperatures.
2-18
Solution
The minimum pressure in a pump to avoid cavitation is to be determined.
Properties
The vapor pressure of water at 25°C is 3.17 kPa.
Analysis
To avoid cavitation, the pressure anywhere in the system should not be allowed to drop below the vapor (or
saturation) pressure at the given temperature. That is,
Pmin = Psat @ 25°C = 3.17 kPa
Therefore, the lowest pressure that can exist in the pump is 3.17 kPa.
Discussion
Note that the vapor pressure increases with increasing temperature, and thus the risk of cavitation is greater
at higher fluid temperatures.
2-8
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
Energy and Specific Heats
2-19C
Solution
We are to discuss the difference between macroscopic and microscopic forms of energy.
Analysis
The macroscopic forms of energy are those a system possesses as a whole with respect to some outside
reference frame. The microscopic forms of energy, on the other hand, are those related to the molecular structure of a
system and the degree of the molecular activity, and are independent of outside reference frames.
Discussion
We mostly deal with macroscopic forms of energy in fluid mechanics.
2-20C
Solution
We are to define total energy and identify its constituents.
Analysis
The sum of all forms of the energy a system possesses is called total energy. In the absence of magnetic,
electrical, and surface tension effects, the total energy of a system consists of the kinetic, potential, and internal
energies.
Discussion
All three constituents of total energy (kinetic, potential, and internal) need to be considered in an analysis of
a general fluid flow.
2-21C
Solution
We are to list the forms of energy that contribute to the internal energy of a system.
Analysis
The internal energy of a system is made up of sensible, latent, chemical, and nuclear energies. The
sensible internal energy is due to translational, rotational, and vibrational effects.
Discussion
We deal with the flow of a single phase fluid in most problems in this textbook; therefore, latent, chemical,
and nuclear energies do not need to be considered.
2-22C
Solution
We are to discuss the relationship between heat, internal energy, and thermal energy.
Analysis
Thermal energy is the sensible and latent forms of internal energy. It does not include chemical or
nuclear forms of energy. In common terminology, thermal energy is referred to as heat. However, like work, heat is not a
property, whereas thermal energy is a property.
Discussion
Technically speaking, “heat” is defined only when there is heat transfer, whereas the energy state of a
substance can always be defined, even if no heat transfer is taking place.
2-23C
Solution
We are to define and discuss flow energy.
Analysis
Flow energy or flow work is the energy needed to push a fluid into or out of a control volume. Fluids at
rest do not possess any flow energy.
Discussion
Flow energy is not a fundamental quantity, like kinetic or potential energy. However, it is a useful concept
in fluid mechanics since fluids are often forced into and out of control volumes in practice.
2-9
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-24C
Solution
We are to compare the energies of flowing and non-flowing fluids.
Analysis
A flowing fluid possesses flow energy, which is the energy needed to push a fluid into or out of a
control volume, in addition to the forms of energy possessed by a non-flowing fluid. The total energy of a non-flowing
fluid consists of internal and potential energies. If the fluid is moving as a rigid body, but not flowing, it may also have
kinetic energy (e.g., gasoline in a tank truck moving down the highway at constant speed with no sloshing). The total
energy of a flowing fluid consists of internal, kinetic, potential, and flow energies.
Discussion
Flow energy is not to be confused with kinetic energy, even though both are zero when the fluid is at rest.
2-25C
Solution
We are to explain how changes in internal energy can be determined.
Analysis
Using specific heat values at the average temperature, the changes in the specific internal energy of ideal
gases can be determined from Δu = c v,avg ΔT . For incompressible substances, cp ≅ cv ≅ c and Δu = c avg ΔT .
Discussion
If the fluid can be treated as neither incompressible nor an ideal gas, property tables must be used.
2-26C
Solution
We are to explain how changes in enthalpy can be determined.
Analysis
Using specific heat values at the average temperature, the changes in specific enthalpy of ideal gases can be
determined from Δh = c p,avg ΔT . For incompressible substances, cp ≅ cv ≅ c and Δh = Δu + vΔP ≅ c avg ΔT + vΔP .
Discussion
If the fluid can be treated as neither incompressible nor an ideal gas, property tables must be used.
Coefficient of Compressibility
2-27C
Solution
We are to discuss the coefficient of compressibility and the isothermal compressibility.
Analysis
The coefficient of compressibility represents the variation of pressure of a fluid with volume or density
at constant temperature. Isothermal compressibility is the inverse of the coefficient of compressibility, and it represents
the fractional change in volume or density corresponding to a change in pressure.
Discussion
The coefficient of compressibility of an ideal gas is equal to its absolute pressure.
2-28C
Solution
We are to define the coefficient of volume expansion.
Analysis
The coefficient of volume expansion represents the variation of the density of a fluid with temperature at
constant pressure. It differs from the coefficient of compressibility in that the latter represents the variation of pressure of
a fluid with density at constant temperature.
Discussion
The coefficient of volume expansion of an ideal gas is equal to the inverse of its absolute temperature.
2-10
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-29C
Solution
We are to discuss the sign of the coefficient of compressibility and the coefficient of volume expansion.
Analysis
The coefficient of compressibility of a fluid cannot be negative, but the coefficient of volume expansion can
be negative (e.g., liquid water below 4°C).
This is the reason that ice floats on water.
Discussion
2-30
Solution
The percent increase in the density of an ideal gas is given for a moderate pressure. The percent increase in
density of the gas when compressed at a higher pressure is to be determined.
Assumptions
The gas behaves an ideal gas.
Analysis
For an ideal gas, P = ρRT and (∂P / ∂ρ ) T = RT = P / ρ , and thus κ ideal gas = P . Therefore, the coefficient
of compressibility of an ideal gas is equal to its absolute pressure, and the coefficient of compressibility of the gas increases
with increasing pressure.
ΔP
ΔP
and rearranging
Substituting κ = P into the definition of the coefficient of compressibility κ ≅ −
≅
Δv / v Δρ / ρ
gives
Δρ
ρ
=
ΔP
P
Therefore, the percent increase of density of an ideal gas during isothermal compression is equal to the percent
increase in pressure.
At 10 atm:
At 100 atm:
Δρ
ΔP 11 − 10
=
= 10%
ρ
P
10
Δρ ΔP 101 − 100
=
=
= 1%
ρ
P
100
=
Therefore, a pressure change of 1 atm causes a density change of 10% at 10 atm and a density change of 1% at 100 atm.
Discussion
If temperature were also allowed to change, the relationship would not be so simple.
2-31
Solution
Using the definition of the coefficient of volume expansion and the expression β ideal gas = 1 / T , it is to be
shown that the percent increase in the specific volume of an ideal gas during isobaric expansion is equal to the percent
increase in absolute temperature.
Assumptions
The gas behaves an ideal gas.
Analysis The coefficient of volume expansion β can be expressed as β =
Noting that β ideal gas = 1 / T for an ideal gas and rearranging give
Δv / v
1 ⎛ ∂v ⎞
.
⎟ ≈
⎜
ΔT
v ⎝ ∂T ⎠ P
Δv ΔT
=
v
T
Therefore, the percent increase in the specific volume of an ideal gas during isobaric expansion is equal to the
percent increase in absolute temperature.
Discussion
We must be careful to use absolute temperature (K or R), not relative temperature (oC or oF).
2-11
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-32
Solution
Water at a given temperature and pressure is compressed to a high pressure isothermally. The increase in
the density of water is to be determined.
Assumptions 1 The isothermal compressibility is constant in the given pressure range. 2 An approximate analysis is
performed by replacing differential changes by finite changes.
Properties
The density of water at 20°C and 1 atm pressure is ρ1 = 998 kg/m3. The isothermal compressibility of water
is given to be α = 4.80 × 10-5 atm-1.
Analysis
When differential quantities are replaced by differences and the properties α and β are assumed to be
constant, the change in density in terms of the changes in pressure and temperature is expressed approximately as
Δρ = αρΔP − βρΔT
The change in density due to a change of pressure from 1 atm to 800 atm at constant temperature is
Δρ = αρΔP = (4.80 × 10 −5 atm -1 )(998 kg/m 3 )(800 − 1)atm = 38.3 kg/m3
Discussion
Note that the density of water increases from 998 to 1036.3 kg/m3 while being compressed, as expected.
This problem can be solved more accurately using differential analysis when functional forms of properties are available.
2-33
Solution
Water at a given temperature and pressure is heated to a higher temperature at constant pressure. The
change in the density of water is to be determined.
Assumptions 1 The coefficient of volume expansion is constant in the given temperature range. 2 An approximate
analysis is performed by replacing differential changes in quantities by finite changes.
Properties
The density of water at 15°C and 1 atm pressure is ρ1 = 999.1 kg/m3. The coefficient of volume expansion
at the average temperature of (15+95)/2 = 55°C is β = 0.484 × 10-3 K-1.
Analysis
When differential quantities are replaced by differences and the properties α and β are assumed to be
constant, the change in density in terms of the changes in pressure and temperature is expressed approximately as
Δρ = αρΔP − βρΔT
The change in density due to the change of temperature from 15°C to 95°C at constant pressure is
Δρ = −βρΔT = −(0.484 × 10 −3 K -1 )(999.1 kg/m 3 )(95 − 15)K = −38.7 kg/m3
Discussion
Noting that Δρ = ρ 2 − ρ1 , the density of water at 95°C and 1 atm is
ρ 2 = ρ1 + Δρ = 999.1 + (−38.7) = 960.4 kg/m 3
which is very close to the listed value of 961.5 kg/m3 at 95°C in water table in the Appendix. This is mostly due to β
varying with temperature almost linearly. Note that the density of water decreases while being heated, as expected. This
problem can be solved more accurately using differential analysis when functional forms of properties are available.
2-12
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-34
Solution
Saturated refrigerant-134a at a given temperature is cooled at constant pressure. The change in the density
of the refrigerant is to be determined.
Assumptions 1 The coefficient of volume expansion is constant in the given temperature range. 2 An approximate
analysis is performed by replacing differential changes in quantities by finite changes.
Properties
The density of saturated liquid R-134a at 10°C is ρ1 =1261 kg/m3. The coefficient of volume expansion at
the average temperature of (10+0)/2 = 5°C is β = 0.00269 K-1.
Analysis
When differential quantities are replaced by differences and the properties α and β are assumed to be
constant, the change in density in terms of the changes in pressure and temperature is expressed approximately as
Δρ = αρΔP − βρΔT
The change in density due to the change of temperature from 10°C to 0°C at constant pressure is
Δρ = −βρΔT = −(0.00269 K -1 )(1261 kg/m 3 )(0 − 10)K = 33.9 kg/m3
Discussion
Noting that Δρ = ρ 2 − ρ1 , the density of R-134a at 0°C is
ρ 2 = ρ1 + Δρ = 1261+ 33.9 = 1294.9 kg/m 3
which is almost identical to the listed value of 1295 kg/m3 at 0°C in R-134a table in the Appendix. This is mostly due to β
varying with temperature almost linearly. Note that the density increases during cooling, as expected.
2-35
Solution
A water tank completely filled with water can withstand tension caused by a volume expansion of 2%. The
maximum temperature rise allowed in the tank without jeopardizing safety is to be determined.
Assumptions 1 The coefficient of volume expansion is constant. 2 An approximate analysis is performed by replacing
differential changes in quantities by finite changes. 3 The effect of pressure is disregarded.
Properties
The average volume expansion coefficient is given to be β = 0.377 × 10-3 K-1.
Analysis
When differential quantities are replaced by differences and the properties α and β are assumed to be
constant, the change in density in terms of the changes in pressure and temperature is expressed approximately as
Δρ = αρΔP − βρΔT
A volume increase of 2% corresponds to a density decrease of 2%, which can be expressed as Δρ = −0.02ρ . Then the
decrease in density due to a temperature rise of ΔT at constant pressure is
−0.02ρ = −βρΔT
Solving for ΔT and substituting, the maximum temperature rise is determined to be
ΔT =
0.02
β
=
0.02
= 53.0 K = 53.0 °C
0.377 × 10 − 3 K -1
Discussion
This result is conservative since in reality the increasing pressure will tend to compress the water and
increase its density.
2-13
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-36
Solution
A water tank completely filled with water can withstand tension caused by a volume expansion of 1%. The
maximum temperature rise allowed in the tank without jeopardizing safety is to be determined.
Assumptions 1 The coefficient of volume expansion is constant. 2 An approximate analysis is performed by replacing
differential changes in quantities by finite changes. 3 The effect of pressure is disregarded.
Properties
The average volume expansion coefficient is given to be β = 0.377 × 10-3 K-1.
Analysis
When differential quantities are replaced by differences and the properties α and β are assumed to be
constant, the change in density in terms of the changes in pressure and temperature is expressed approximately as
Δρ = αρΔP − βρΔT
A volume increase of 1% corresponds to a density decrease of 1%, which can be expressed as Δρ = −0.01ρ . Then the
decrease in density due to a temperature rise of ΔT at constant pressure is
−0.01ρ = −βρΔT
Solving for ΔT and substituting, the maximum temperature rise is determined to be
ΔT =
0.01
β
=
0.01
= 26.5 K = 26.5 °C
0.377 × 10 − 3 K -1
Discussion
This result is conservative since in reality the increasing pressure will tend to compress the water and
increase its density. The change in temperature is exactly half of that of the previous problem, as expected.
2-14
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-37
Solution
The density of seawater at the free surface and the bulk modulus of elasticity are given. The density and
pressure at a depth of 2500 m are to be determined.
Assumptions 1 The temperature and the bulk modulus of elasticity of seawater is constant. 2 The gravitational
acceleration remains constant.
Properties
The density of seawater at free surface where the pressure is given to be 1030 kg/m3, and the bulk modulus
of elasticity of seawater is given to be 2.34 × 109 N/m2.
The coefficient of compressibility or the bulk modulus of elasticity of fluids is expressed as
Analysis
⎛ ∂P ⎞
κ = ρ ⎜⎜ ⎟⎟
⎝ ∂ρ ⎠ T
κ=ρ
or
dP
dρ
(at constant T )
The differential pressure change across a differential fluid height of dz is given as
z=0
dP = ρgdz
z
Combining the two relations above and rearranging,
κ=ρ
ρgdz
dz
= gρ 2
dρ
dρ
dρ
→
ρ
2
=
gdz
2500 m
κ
Integrating from z = 0 where ρ = ρ 0 = 1030 kg/m 3 to z = z where ρ = ρ gives
dρ
ρ
∫ρ
ρ
0
2
g
κ∫
=
z
0
dz
→
1
ρ0
−
1
ρ
=
gz
κ
Solving for ρ gives the variation of density with depth as
ρ=
1
1
/
−
ρ
( 0 ) ( gz / κ )
Substituting into the pressure change relation dP = ρgdz and integrating from z = 0 where P = P0 = 98 kPa to z = z where
P = P gives
∫
dP = ∫
P
z
0
P0
gdz
(1 / ρ0 ) − ( gz / κ )
→
⎛
⎞
1
P = P0 + κ ln ⎜⎜
⎟⎟
⎝ 1 − ( ρ 0 gz / κ ) ⎠
which is the desired relation for the variation of pressure in seawater with depth. At z = 2500 m, the values of density and
pressure are determined by substitution to be
ρ=
1
1 /(1030 kg/m ) − (9.81 m/s )(2500 m) /(2.34 × 10 9 N/m 2 )
3
2
= 1041 kg/m 3
⎛
⎞
1
⎟
P = (98,000 Pa) + (2.34 × 10 9 N/m 2 ) ln⎜⎜
3
2
9
2 ⎟
⎝ 1 − (1030 kg/m )(9.81 m/s )(2500 m) /( 2.34 × 10 N/m ) ⎠
= 2.550 × 10 7 Pa
= 25.50 MPa
since 1 Pa = 1 N/m2 = 1 kg/m⋅s2 and 1 kPa = 1000 Pa.
Discussion
Note that if we assumed ρ = ρo = constant at 1030 kg/m3, the pressure at 2500 m would be P = P0 + ρgz =
0.098 + 25.26 = 25.36 MPa. Then the density at 2500 m is estimated to be
Δρ = ραΔP = (1030)(2340 MPa) −1 (25.26 MPa) = 11.1 kg/m 3 and thus ρ = 1041 kg/m3
2-15
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
Viscosity
2-38C
Solution
We are to define and discuss viscosity.
Analysis
Viscosity is a measure of the “stickiness” or “resistance to deformation” of a fluid. It is due to the
internal frictional force that develops between different layers of fluids as they are forced to move relative to each other.
Viscosity is caused by the cohesive forces between the molecules in liquids, and by the molecular collisions in gases. In
general, liquids have higher dynamic viscosities than gases.
Discussion
The ratio of viscosity μ to density ρ often appears in the equations of fluid mechanics, and is defined as the
kinematic viscosity, ν = μ /ρ.
2-39C
Solution
We are to discuss Newtonian fluids.
Analysis
Fluids whose shear stress is linearly proportional to the velocity gradient (shear strain) are called
Newtonian fluids. Most common fluids such as water, air, gasoline, and oils are Newtonian fluids.
Discussion
In the differential analysis of fluid flow, only Newtonian fluids are considered in this textbook.
2-40C
Solution
We are to compare the settling speed of balls dropped in water and oil; namely, we are to determine which
will reach the bottom of the container first.
Analysis
When two identical small glass balls are dropped into two identical containers, one filled with water and the
other with oil, the ball dropped in water will reach the bottom of the container first because of the much lower
viscosity of water relative to oil.
Discussion
Oil is very viscous, with typical values of viscosity approximately 800 times greater than that of water at
room temperature.
2-41C
Solution
We are to discuss how dynamic viscosity varies with temperature in liquids and gases.
Analysis
(a) The dynamic viscosity of liquids decreases with temperature. (b) The dynamic viscosity of gases
increases with temperature.
Discussion
A good way to remember this is that a car engine is much harder to start in the winter because the oil in the
engine has a higher viscosity at low temperatures.
2-42C
Solution
We are to discuss how kinematic viscosity varies with temperature in liquids and gases.
Analysis
(a) For liquids, the kinematic viscosity decreases with temperature. (b) For gases, the kinematic
viscosity increases with temperature.
Discussion
You can easily verify this by looking at the appendices.
2-16
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-43
Solution
A block is moved at constant velocity on an inclined surface. The force that needs to be applied in the
horizontal direction when the block is dry, and the percent reduction in the required force when an oil film is applied on the
surface are to be determined.
Assumptions 1 The inclined surface is plane (perfectly flat, although tilted). 2 The friction coefficient and the oil film
thickness are uniform. 3 The weight of the oil layer is negligible.
The absolute viscosity of oil is given to be μ = 0.012 Pa⋅s = 0.012 N⋅s/m2.
Properties
Analysis
(a) The velocity of the block is constant, and thus its
acceleration and the net force acting on it are zero. A free body diagram of the
block is given. Then the force balance gives
F1
F x = 0 : F1 − F f cos 20° − FN 1 sin 20° = 0 (1)
∑
∑F
y
FN 1 cos 20° − F f sin 20° − W = 0
= 0:
Friction force: F f = fFN 1
(2)
V= 0.8 m/s
Ff
200
y
0
FN1
200
W = 150 N
20
(3)
x
Substituting Eq. (3) into Eq. (2) and solving for FN1 gives
150 N
W
=
= 177.0 N
FN 1 =
cos 20° − f sin 20° cos 20° − 0.27 sin 20°
Then from Eq. (1):
F1 = F f cos 20° + FN1 sin 20° = (0.27 ×177 N) cos 20° + (177 N) sin 20° = 105.5 N
(b) In this case, the friction force is replaced by the shear force
applied on the bottom surface of the block due to the oil. Because
of the no-slip condition, the oil film sticks to the inclined surface
at the bottom and the lower surface of the block at the top. Then
the shear force is expressed as
Fshear = τ w As
V
= μ As
h
= ( 0.012 N ⋅ s/m 2 )( 0.5 × 0.2 m 2 )
V= 0.8 m/s
50 cm
F2
0
20
0.8 m/s
4 × 10-4 m
0.4 mm
Fshear = τwAs
FN2
W = 150 N
= 2.4 N
Replacing the friction force by the shear force in part (a),
∑F
∑F
x
= 0:
F2 − Fshear cos 20° − FN 2 sin 20° = 0
(4)
y
= 0:
FN 2 cos 20° − Fshear sin 20° − W = 0
(5)
Eq. (5) gives FN 2 = ( Fshear sin 20° + W ) / cos 20° = [(2.4 N) sin 20° + (150 N)] / cos 20° = 160.5 N
Substituting into Eq. (4), the required horizontal force is determined to be
F2 = Fshear cos 20° + FN 2 sin 20° = (2.4 N) cos 20° + (160.5 N) sin 20° = 57.2 N
Then, our final result is expressed as
F − F2
105.5 − 57.2
Percentage reduction in required force = 1
× 100% =
× 100% = 45.8%
F1
105.5
Discussion
Note that the force required to push the block on the inclined surface reduces significantly by oiling the
surface.
2-17
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-44
Solution
The velocity profile of a fluid flowing though a circular pipe is given. The friction drag force exerted on the
pipe by the fluid in the flow direction per unit length of the pipe is to be determined.
Assumptions
The viscosity of the fluid is constant.
Analysis
The wall shear stress is determined from its definition to be
nμu max
d ⎛
rn ⎞
− nr n −1
⎜1 −
⎟
u
=
−
=
μ
max
n ⎟
n
⎜
dr ⎝ R ⎠ r = R
R
R
r =R
r=R
Note that the quantity du /dr is negative in pipe flow, and the negative sign
is added to the τw relation for pipes to make shear stress in the positive
(flow) direction a positive quantity. (Or, du /dr = - du /dy since y = R – r).
Then the friction drag force exerted by the fluid on the inner surface of the
pipe becomes
nμu max
F = τ w Aw =
( 2πR ) L = 2nπμu max L
R
Therefore, the drag force per unit length of the pipe is
τ w = −μ
du
dr
= − μu max
u(r) = umax(1-rn/Rn)
R
r
0
umax
F / L = 2nπμu max .
Discussion
Note that the drag force acting on the pipe in this case is independent of the pipe diameter.
2-18
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-45
Solution
A thin flat plate is pulled horizontally through an oil layer sandwiched between two plates, one stationary
and the other moving at a constant velocity. The location in oil where the velocity is zero and the force that needs to be
applied on the plate are to be determined.
Assumptions
1 The thickness of the plate is negligible. 2 The velocity profile in each oil layer is linear.
Properties
The absolute viscosity of oil is given to be μ = 0.027 Pa⋅s = 0.027 N⋅s/m2.
Analysis
(a) The velocity profile in each oil layer relative to the fixed wall is as shown in the figure below. The point
of zero velocity is indicated by point A, and its distance from the lower plate is determined from geometric considerations
(the similarity of the two triangles in the lower oil layer) to be
2.6 − y A
1
=
0.3
yA
→ yA = 0.60 mm
Fixed wall
h1=1 mm
V = 1 m/s
h2=2.6 mm
y
F
A
yA
Vw= 0.3 m/s
Moving wall
(b) The magnitudes of shear forces acting on the upper and lower surfaces of the plate are
Fshear, upper = τ w, upper As = μAs
1 m/s
du
V −0
= μAs
= (0.027 N ⋅ s/m 2 )(0.2 × 0.2 m 2 )
= 1.08 N
dy
h1
1.0 × 10 -3 m
Fshear, lower = τ w, lower As = μAs
V − Vw
[1 − (−0.3)] m/s
du
= 0.54 N
= μAs
= (0.027 N ⋅ s/m 2 )(0.2 × 0.2 m 2 )
dy
h2
2.6 × 10 -3 m
Noting that both shear forces are in the opposite direction of motion of the plate, the force F is determined from a force
balance on the plate to be
F = Fshear, upper + Fshear, lower = 1.08 + 0.54 = 1.62 N
Discussion
motion.
Note that wall shear is a friction force between a solid and a liquid, and it acts in the opposite direction of
2-19
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-46
Solution
A frustum shaped body is rotating at a constant
angular speed in an oil container. The power required to
maintain this motion and the reduction in the required power
input when the oil temperature rises are to be determined.
Assumptions The thickness of the oil layer remains constant.
Properties
The absolute viscosity of oil is given to be μ =
0.1 Pa⋅s = 0.1 N⋅s/m2 at 20°C and 0.0078 Pa⋅s at 80°C.
Analysis
The velocity gradient anywhere in the oil of
film thickness h is V/h where V = ωr is the tangential
velocity. Then the wall shear stress anywhere on the surface of
the frustum at a distance r from the axis of rotation is
ωr
du
V
τw = μ
=μ =μ
dr
h
h
The shear force acting on differential area dA on the surface,
the torque it generates, and the shaft power associated with it
are expressed as
dF = τ w dA = μ
T=
μω
h
∫
ωr
h
dA
dT = rdF = μ
ωr 2
h
μω 2
W sh = ωT =
h
r 2 dA
A
Case
D = 12 cm
L = 12 cm
d = 4 cm
z
SAE 10W oil of
film thickness h
r
dA
∫r
2
dA
A
Top surface: For the top surface, dA = 2πrdr . Substituting and integrating,
μω 2
W sh, top =
h
∫
D/2
r =0
r 2 (2πr )dr =
2πμω 2
h
∫
D/2
r =0
r 3 dr =
2πμω 2 r 4
h
4
D/2
=
πμω 2 D 4
32h
r =0
πμω 2 d 4
Bottom surface: A relation for the bottom surface is obtained by replacing D by d, W sh, bottom =
32 h
Side surface: The differential area for the side surface can be expressed as dA = 2πrdz . From geometric considerations, the
d D−d
variation of radius with axial distance is expressed as r = +
z.
2
2L
2L
4πL
D−d
Differentiating gives dr =
dr . Therefore, dA = 2πdz =
rdr . Substituting and integrating,
dz or dz =
D−d
D−d
2L
μω 2
W sh, top =
h
∫
D/2
r =0
4πμω 2 L
4πL
rdr =
r
D−d
h( D − d )
2
∫
D/2
r =d / 2
4πμω 2 L r 4
r dr =
h( D − d ) 4
D/2
=
3
r =d / 2
πμω 2 L( D 2 − d 2 )
16 h( D − d )
Then the total power required becomes
2 L[1 − (d / D ) 4 )] ⎤
πμω 2 D 4 ⎡
4
+
+
d
D
W sh, total = W sh, top + W sh, bottom + W sh, side =
1
(
/
)
⎥,
⎢
D−d
32h ⎣
⎦
where d/D = 4/12 = 1/3. Substituting,
π (0.1 N ⋅ s/m 2 )(200 /s) 2 (0.12 m) 4
W sh, total =
32(0.0012 m)
⎡
2(0.12 m)[1 − (1 / 3) 4 )] ⎤⎛ 1 W ⎞
4
⎟ = 270 W
⎢1 + (1 / 3) +
⎥⎜
(0.12 − 0.04) m ⎥⎦⎝ 1 Nm/s ⎠
⎢⎣
Noting that power is proportional to viscosity, the power required at 80°C is
μ
0.0078 N ⋅ s/m 2
(270 W) = 21.1 W
W sh, total, 80°C = 80°C W sh, total, 20°C =
μ 20°C
0.1 N ⋅ s/m 2
Therefore, the reduction in the requires power input at 80°C is Reduction = Wsh, total, 20°C − Wsh, total, 80°C = 270 − 21.1 = 249 W ,
which is about 92%.
Discussion
Note that the power required to overcome shear forces in a viscous fluid greatly depends on temperature.
-
2-20
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-47
Solution
A clutch system is used to transmit torque through an oil film between two identical disks. For specified
rotational speeds, the transmitted torque is to be determined.
Assumptions
1 The thickness of the oil film is uniform. 2 The rotational speeds of the disks remain constant.
Properties
The absolute viscosity of oil is given to be μ = 0.38 N⋅s/m2.
Driving
shaft
Driven
shaft
30 cm
3 mm
SAE 30W oil
Analysis
The disks are rotting in the same direction at different angular speeds of ω1 and of ω2 . Therefore, we can
assume one of the disks to be stationary and the other to be rotating at an angular speed of ω1 − ω 2 . The velocity gradient
anywhere in the oil of film thickness h is V /h where V = (ω1 − ω 2 )r is the tangential velocity. Then the wall shear stress
anywhere on the surface of the faster disk at a distance r from the axis of rotation can be expressed as
(ω − ω 2 )r
du
V
τw = μ
=μ =μ 1
dr
h
h
h
Then the shear force acting on a differential area dA on the surface and the
torque generation associated with it can be expressed as
ω2r
(ω − ω 2 )r
dF = τ w dA = μ 1
(2πr )dr
ω1r
h
dT = rdF = μ
(ω1 − ω 2 )r 2
2πμ (ω1 − ω 2 ) 3
r dr
(2πr )dr =
h
h
Integrating,
T=
2πμ (ω1 − ω 2 )
h
∫
D/2
r =0
r 3 dr =
2πμ (ω1 − ω 2 ) r 4
h
4
D/2
=
πμ (ω1 − ω 2 ) D 4
r =0
32h
Noting that ω = 2π n , the relative angular speed is
⎛ 1 min ⎞
ω1 − ω2 = 2π ( n1 − n2 ) = ( 2π rad/rev ) ⎡⎣(1450 − 1398 ) rev/min ⎤⎦ ⎜
⎟ = 5.445 rad/s ,
⎝ 60 s ⎠
Substituting, the torque transmitted is determined to be
T=
π (0.38 N ⋅ s/m 2 )(5.445 /s)(0.30 m) 4
32(0.003 m)
= 0.55 N ⋅ m
Discussion Note that the torque transmitted is proportional to the fourth power of disk diameter, and is inversely
proportional to the thickness of the oil film.
2-21
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-48
Solution
We are to investigate the effect of oil film thickness on the transmitted torque.
Analysis
The previous problem is reconsidered. Using EES software, the effect of oil film thickness on the
torque transmitted is investigated. Film thickness varied from 0.1 mm to 10 mm, and the results are tabulated and
πμ (ω1 − ω 2 ) D 4
. The EES Equations window is printed below, followed by the
plotted. The relation used is T =
32h
tabulated and plotted results.
mu=0.38
n1=1450 "rpm"
w1=2*pi*n1/60 "rad/s"
n2=1398 "rpm"
w2=2*pi*n2/60 "rad/s"
D=0.3 "m"
Tq=pi*mu*(w1-w2)*(D^4)/(32*h)
18
Torque transmitted
T, Nm
16.46
8.23
4.11
2.74
2.06
1.65
0.82
0.41
0.27
0.21
0.16
16
14
12
Tq [Nm]
Film thickness
h, mm
0.1
0.2
0.4
0.6
0.8
1
2
4
6
8
10
10
8
6
4
2
0
0
0.002
0.004
0.006
0.008
0.01
h [m]
Conclusion Torque transmitted is inversely proportional to oil film thickness, and the film thickness should be as small as
possible to maximize the transmitted torque.
Discussion
value of h.
To obtain the solution in EES, we set up a parametric table, specify h, and let EES calculate T for each
2-22
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-49
Solution
A multi-disk Electro-rheological “ER” clutch is considered. The ER fluid has a shear stress that is expressed
as τ = τ y + μ (du dy ) . A relationship for the torque transmitted by the clutch is to be obtained, and the numerical value of
the torque is to be calculated.
Assumptions 1 The thickness of the oil layer between the disks is constant. 2 The Bingham plastic model for shear stress
expressed as τ = τ y + μ (du dy ) is valid.
The constants in shear stress relation are given to be μ = 0.1 Pa⋅s and τy = 2.5 kPa.
Properties
h = 1.2 mm
Shell
R2
R1
Output shaft
Input shaft
Plates mounted on shell
Plates mounted on input shaft
Variable magnetic field
Analysis (a) The velocity gradient anywhere in the oil of film thickness h is V/h where V = ωr is the tangential velocity
relative to plates mounted on the shell. Then the wall shear stress anywhere on the surface of a plate mounted on the input
shaft at a distance r from the axis of rotation is expressed as
ωr
du
V
=τ y + μ =τ y + μ
dr
h
h
Then the shear force acting on a differential area dA on the surface of a disk and the torque generation associated with it are
expressed as
ωr ⎞
⎛
dF = τ w dA = ⎜τ y + μ
⎟(2πr )dr
h ⎠
⎝
τ w =τ y + μ
⎛
ωr ⎞
ωr 3 ⎞
⎛
2
⎟dr
dT = rdF = r ⎜τ y + μ
⎟(2πr )dr = 2π ⎜⎜τ y r + μ
h ⎟⎠
h ⎠
⎝
⎝
Integrating,
T = 2π
∫
R2
r = R1
⎡ r 3 μωr 4 ⎤ 2
⎛
⎤
⎡τ y
μω 4
ωr 3 ⎞
⎟⎟dr = 2π ⎢τ y
⎜⎜τ y r 2 + μ
+
= 2π ⎢ ( R 23 − R13 ) +
( R 2 − R14 )⎥
⎥
h
3
4
3
4
h
h
⎦
⎣
⎠
⎝
⎣
⎦ r = R1
R
This is the torque transmitted by one surface of a plate mounted on the input shaft. Then the torque transmitted by both
surfaces of N plates attached to input shaft in the clutch becomes
⎡τ y
⎤
μω 4
T = 4πN ⎢ ( R 23 − R13 ) +
( R 2 − R14 )⎥
4h
⎣ 3
⎦
(b) Noting that ω = 2πn = 2π (2400 rev/min) = 15,080 rad/min = 251.3 rad/s and substituting,
⎤
⎡ 2500 N/m 2
(0.1 N ⋅ s/m 2 )(251.3 /s)
T = (4π )(11) ⎢
[(0.20 m) 3 − (0.05 m ) 3 ] +
[(0.20 m) 4 − (0.05 m ) 4 ]⎥ = 2060 N ⋅ m
3
4(0.0012 m)
⎦
⎣
Discussion
Can you think of some other potential applications for this kind of fluid?
2-23
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-50
Solution
A multi-disk magnetorheological “MR” clutch is considered The MR fluid has a shear stress that is
expressed as τ = τ y + K ( du dy ) m . A relationship for the torque transmitted by the clutch is to be obtained, and the
numerical value of the torque is to be calculated.
Assumptions 1 The thickness of the oil layer between the disks is constant. 2 The Herschel-Bulkley model for shear stress
expressed as τ = τ y + K ( du dy ) m is valid.
Properties
The constants in shear stress relation are given to be τy = 900 Pa, K = 58 Pa⋅sm , and m = 0.82.
h = 1.2 mm
Shell
R2
R1
Output shaft
Input shaft
Plates mounted on shell
Plates mounted on input shaft
Variable magnetic field
Analysis (a) The velocity gradient anywhere in the oil of film thickness h is V/h where V = ωr is the tangential velocity
relative to plates mounted on the shell. Then the wall shear stress anywhere on the surface of a plate mounted on the input
shaft at a distance r from the axis of rotation is expressed as
m
m
ωr m
du
V
τ w = τ y + K ⎛⎜ ⎞⎟ = τ y + K ⎛⎜ ⎞⎟ = τ y + K ⎛⎜ ⎞⎟
⎝h⎠
⎝ h ⎠
⎝ dr ⎠
Then the shear force acting on a differential area dA on the surface of a disk and the torque generation associated with it are
expressed as
m +2 ⎞
m
m
⎛
⎛
⎛
ω mr
⎛ ωr ⎞ ⎞⎟
⎛ ωr ⎞ ⎞⎟
2
⎟dr
⎜
⎜
⎜
dF = τ w dA = τ y + K ⎜ ⎟ (2πr )dr and dT = rdF = r τ y + K ⎜ ⎟ (2πr )dr = 2π τ y r + K m
⎜
⎜
⎟
⎜
⎝ h ⎠ ⎟⎠
⎝ h ⎠ ⎟⎠
h
⎝
⎝
⎠
⎝
Integrating,
R
m+ 2 ⎞
R2 ⎛
⎤
⎡τ y
⎡ r 3 Kω m r m + 3 ⎤ 2
ω mr
Kω m
3
3
2
⎜
⎟
τ yr + K m
π
=
−
+
+
2
(
)
( R 2m + 3 − R1m + 3 )⎥
T = 2π
dr = 2π ⎢τ y
R
R
⎢
⎥
2
1
m
m
⎟
R1 ⎜
3 (m + 3)h ⎦ R
(m + 3)h
h
⎦
⎣ 3
⎣
⎝
⎠
1
This is the torque transmitted by one surface of a plate mounted on the input shaft. Then the torque transmitted by both
surfaces of N plates attached to input shaft in the clutch becomes
⎤
⎡τ y
Kω m
T = 4πN ⎢ ( R 23 − R13 ) +
( R 2m + 3 − R1m + 3 )⎥
m
(m + 3)h
⎦
⎣ 3
(b) Noting that ω = 2πn = 2π (2400 rev/min) = 15,080 rad/min = 251.3 rad/s and substituting,
∫
0.82
⎡ 900 N/m 2
⎤
58 N ⋅ s0.82 /m 2 ) ( 251.3 /s )
(
3
3
⎡
⎤
⎡( 0.20 m )3.82 − ( 0.05 m )3.82 ⎤ ⎥
⎢
T = ( 4π )(11)
0.20 m ) − ( 0.05 m ) +
(
0.82
⎣
⎦
⎣
⎦⎥
3
⎢
( 0.82 + 3)( 0.0012 m )
⎣
⎦
= 103.4 N ≅ 103 kN ⋅ m
Discussion
Can you think of some other potential applications for this kind of fluid?
2-24
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-51
Solution
determined.
The torque and the rpm of a double cylinder viscometer are given. The viscosity of the fluid is to be
Assumptions 1 The inner cylinder is completely submerged in oil. 2 The
viscous effects on the two ends of the inner cylinder are negligible. 3 The fluid
is Newtonian.
Analysis
Substituting the given values, the viscosity of the fluid is
determined to be
(0.8 N ⋅ m)(0.0012 m)
TA
=
= 0.0231 N ⋅ s/m 2
μ=
2 3
2
3
-1
4π R n L 4π (0.075 m) (200 / 60 s )(0.75 m)
R
l = 0.12 cm
fluid
Discussion
This is the viscosity value at the temperature that existed during
the experiment. Viscosity is a strong function of temperature, and the values
can be significantly different at different temperatures.
2-52E
Solution
The torque and the rpm of a double cylinder viscometer are
given. The viscosity of the fluid is to be determined.
Assumptions 1 The inner cylinder is completely submerged in the fluid. 2
The viscous effects on the two ends of the inner cylinder are negligible. 3 The
fluid is Newtonian.
Analysis Substituting the given values, the viscosity of the fluid is determined
to be
(1.2 lbf ⋅ ft)(0.05/12 ft)
TA
=
= 9.97 × 10 −5 lbf ⋅ s/ft 2
μ=
2 3
2
3
-1
4π R nL 4π (5.6 / 12 ft) (250 / 60 s )(3 ft)
R
l = 0.05 in
fluid
Discussion
This is the viscosity value at temperature that existed during
the experiment. Viscosity is a strong function of temperature, and the values can be significantly different at different
temperatures.
2-25
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-53
Solution
The velocity profile for laminar one-dimensional flow through a circular pipe is given. A relation for
friction drag force exerted on the pipe and its numerical value for water are to be determined.
Assumptions
1 The flow through the circular pipe is one-dimensional. 2 The fluid is Newtonian.
Properties
The viscosity of water at 20°C is given to be 0.0010 kg/m⋅s.
⎛
r2 ⎞
The velocity profile is given by u (r ) = u max ⎜⎜1 − 2 ⎟⎟
⎝ R ⎠
where R is the radius of the pipe, r is the radial distance from the center of
the pipe, and umax is the maximum flow velocity, which occurs at the
center, r = 0. The shear stress at the pipe surface is expressed as
Analysis
τ w = −μ
du
dr
r =R
= − μu max
− 2r
d ⎛
r2 ⎞
⎟
⎜1 −
= − μu max 2
2 ⎟
⎜
dr ⎝ R ⎠ r = R
R
=
r =R
u(r) = umax(1-r2/R2)
R
r
0
umax
2μu max
R
Note that the quantity du/dr is negative in pipe flow, and the negative sign is added to the τw relation for pipes to make
shear stress in the positive (flow) direction a positive quantity. (Or, du/dr = −du/dy since y = R – r). Then the friction drag
force exerted by the fluid on the inner surface of the pipe becomes
2 μu max
F D = τ w As =
( 2πRL ) = 4πμLu max
R
⎞
⎛
1N
⎟ = 0.565 N
Substituting we get FD = 4πμLu max = 4π (0.0010 kg/m ⋅ s)(15 m)(3 m/s)⎜
⎜ 1 kg ⋅ m/s 2 ⎟
⎠
⎝
Discussion
In the entrance region and during turbulent flow, the velocity gradient is greater near the wall, and thus the
drag force in such cases will be greater.
2-54
Solution
The velocity profile for laminar one-dimensional flow through a circular pipe is given. A relation for
friction drag force exerted on the pipe and its numerical value for water are to be determined.
Assumptions
Properties
1 The flow through the circular pipe is one-dimensional. 2 The fluid is Newtonian.
The viscosity of water at 20°C is given to be 0.0010 kg/m⋅s.
⎛
r ⎞
The velocity profile is given by u (r ) = u max ⎜⎜1 − 2 ⎟⎟
⎝ R ⎠
where R is the radius of the pipe, r is the radial distance from the center of
the pipe, and umax is the maximum flow velocity, which occurs at the
center, r = 0. The shear stress at the pipe surface can be expressed as
u(r) = umax(1-r2/R2)
2
Analysis
τ w = −μ
du
dr
r =R
= − μu max
− 2r
d ⎛
r2 ⎞
⎟
⎜1 −
= − μu max 2
2 ⎟
⎜
dr ⎝ R ⎠ r = R
R
=
r =R
2μu max
R
R
r
0
umax
Note that the quantity du/dr is negative in pipe flow, and the negative sign is added to the τw relation for pipes to make
shear stress in the positive (flow) direction a positive quantity. (Or, du/dr = −du/dy since y = R – r). Then the friction drag
force exerted by the fluid on the inner surface of the pipe becomes
2 μu max
F D = τ w As =
( 2πRL ) = 4πμLu max
R
⎞
⎛
1N
⎟ = 0.942 N
Substituting, we get FD = 4πμLu max = 4π (0.0010 kg/m ⋅ s)(15 m)(5 m/s)⎜
2
⎜ 1 kg ⋅ m/s ⎟
⎠
⎝
Discussion
In the entrance region and during turbulent flow, the velocity gradient is greater near the wall, and thus the
drag force in such cases will be larger.
2-26
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
Surface Tension and Capillary Effect
2-55C
Solution
We are to define and discuss surface tension.
Analysis
The magnitude of the pulling force at the surface of a liquid per unit length is called surface tension σs.
It is caused by the attractive forces between the molecules. The surface tension is also surface energy (per unit area) since it
represents the stretching work that needs to be done to increase the surface area of the liquid by a unit amount.
Discussion
Surface tension is the cause of some very interesting phenomena such as capillary rise and insects that can
walk on water.
2-56C
Solution
We are to analyze the pressure difference between inside and outside of a soap bubble.
Analysis
The pressure inside a soap bubble is greater than the pressure outside, as evidenced by the stretch of
the soap film.
Discussion
You can make an analogy between the soap film and the skin of a balloon.
2-57C
Solution
We are to define and discuss the capillary effect.
Analysis
The capillary effect is the rise or fall of a liquid in a small-diameter tube inserted into the liquid. It is
caused by the net effect of the cohesive forces (the forces between like molecules, like water) and adhesive forces (the
forces between unlike molecules, like water and glass). The capillary effect is proportional to the cosine of the contact
angle, which is the angle that the tangent to the liquid surface makes with the solid surface at the point of contact.
Discussion
The contact angle determines whether the meniscus at the top of the column is concave or convex.
2-58C
Solution
We are to determine whether the level of liquid in a tube will rise or fall due to the capillary effect.
Analysis
The liquid level in the tube will drop since the contact angle is greater than 90°, and cos(110°) < 0.
Discussion
This liquid must be a non-wetting liquid when in contact with the tube material. Mercury is an example of a
non-wetting liquid with a contact angle (with glass) that is greater than 90o.
2-59C
Solution
We are to compare the capillary rise in small and large diameter tubes.
Analysis
The capillary rise is inversely proportional to the diameter of the tube, and thus capillary rise is greater in
the smaller-diameter tube.
Discussion
Note however, that if the tube diameter is large enough, there is no capillary rise (or fall) at all. Rather, the
upward (or downward) rise of the liquid occurs only near the tube walls; the elevation of the middle portion of the liquid in
the tube does not change for large diameter tubes.
2-27
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-60E
Solution
A slender glass tube is inserted into kerosene. The capillary rise of kerosene in the tube is to be determined.
Assumptions 1 There are no impurities in the kerosene, and no contamination on the
surfaces of the glass tube. 2 The kerosene is open to the atmospheric air.
Properties
The surface tension of kerosene-glass at 68°F (20°C) is σs =
0.028×0.06852 = 0.00192 lbf/ft. The density of kerosene at 68°F is ρ = 51.2 lbm/ft3.
The contact angle of kerosene with the glass surface is given to be 26°.
Substituting the numerical values, the capillary rise is determined to be
Analysis
h=
2 ( 0.00192 lbf/ft )( cos26° )
⎛ 32.2 lbm ⋅ ft/s 2 ⎞
2σ s cosφ
=
⎜
ρ gR
( 51.2 lbm/ft 3 )( 32.2 ft/s2 ) ( 0.015 / 12 ft ) ⎝ 1 lbf ⎟⎠
= 0.0539 ft = 0.650 in
Discussion
The capillary rise in this case more than half of an inch, and thus it is clearly noticeable.
2-61
A glass tube is inserted into a liquid, and the capillary rise is measured.
Solution
The surface tension of the liquid is to be determined.
Assumptions 1 There are no impurities in the liquid, and no contamination on the
surfaces of the glass tube. 2 The liquid is open to the atmospheric air.
Properties
The density of the liquid is given to be 960 kg/m3. The contact angle is
given to be 15°.
h
Air
Liquid
Analysis
Substituting the numerical values, the surface tension is determined from
the capillary rise relation to be
⎞
ρgRh (960 kg/m 3 )(9.81 m/s 2 )(0.0019 / 2 m)(0.005 m) ⎛⎜
1N
⎟ = 0.0232 N/m
σs =
=
2
⎟
⎜
2 cos φ
2(cos 15°)
1
kg
m/s
⋅
⎠
⎝
Discussion
Since surface tension depends on temperature, the value determined is valid at the liquid’s temperature.
2-62
Solution
The diameter of a soap bubble is given. The gage pressure inside the bubble is to be determined.
Assumptions
The soap bubble is in atmospheric air.
Properties
The surface tension of soap water at 20°C is σs = 0.025 N/m.
Analysis
The pressure difference between the inside and the outside of a
bubble is given by
4σ s
ΔPbubble = Pi − P0 =
R
In the open atmosphere P0 = Patm, and thus ΔPbubble is equivalent to the gage
pressure. Substituting,
P0
Soap
bubble
P
4(0.025 N/m)
= 100 N/m 2 = 100 Pa
0.002/2 m
4(0.025 N/m)
=
= 4 N/m 2 = 4 Pa
0.05/2 m
Pi , gage = ΔPbubble =
Pi , gage = ΔPbubble
Discussion
Note that the gage pressure in a soap bubble is inversely proportional to the radius. Therefore, the excess
pressure is larger in smaller bubbles.
2-28
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-63
Solution
Nutrients dissolved in water are carried to upper parts of plants. The
height to which the water solution rises in a tree as a result of the capillary effect is to
be determined.
Assumptions 1 The solution can be treated as water with a contact angle of 15°. 2
The diameter of the tube is constant. 3 The temperature of the water solution is 20°C.
Properties
The surface tension of water at 20°C is σs = 0.073 N/m. The density of
water solution can be taken to be 1000 kg/m3. The contact angle is given to be 15°.
Substituting the numerical values, the capillary rise is determined to be
Analysis
h=
⎛ 1 kg ⋅ m/s 2
2σ s cos φ
2(0.073 N/m)(cos 15°)
⎜
=
ρgR
1N
(1000 kg/m 3 )(9.81 m/s 2 )(2.5 × 10 −6 m) ⎜⎝
⎞
⎟ = 5.75 m
⎟
⎠
Discussion
Other effects such as the chemical potential difference also cause the
fluid to rise in trees.
2-64
Solution
The force acting on the movable wire of a liquid film suspended on a U-shaped wire frame is measured. The
surface tension of the liquid in the air is to be determined.
Assumptions 1 There are no impurities in the liquid, and no contamination on the surfaces of the wire frame. 2 The liquid
is open to the atmospheric air.
Substituting the numerical values, the surface tension is determined from the surface tension force relation
Analysis
to be
σs =
F
0.012 N
=
= 0.075 N/m
2b 2(0.08 m)
b
Liquid
film
F
Discussion
The surface tension depends on temperature. Therefore, the value
determined is valid at the temperature of the liquid.
2-29
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-65
Solution
A steel ball floats on water due to the surface tension effect. The maximum diameter of the ball is to be
determined, and the calculations are to be repeated for aluminum.
σ
Assumptions 1 The water is pure, and its
temperature is constant. 2 The ball is dropped on
water slowly so that the inertial effects are negligible.
3 The contact angle is taken to be 0° for maximum
diameter.
Properties
The surface tension of water at 20°C
is σs = 0.073 N/m. The contact angle is taken to be
0°. The densities of steel and aluminum are given to
be ρsteel = 7800 kg/m3 and ρAl = 2700 kg/m3.
W = mg
Analysis
The surface tension force and the
weight of the ball can be expressed as
Fs = πDσ s
and W = mg = ρgV = ρgπD 3 / 6
When the ball floats, the net force acting on the ball in the vertical direction is zero. Therefore, setting Fs = W and solving
for diameter D gives D =
6σ s
. Substititing the known quantities, the maximum diameters for the steel and aluminum
ρg
balls become
D steel =
6σ s
=
ρg
⎛ 1 kg ⋅ m/s 2
⎜
1N
(7800 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
6(0.073 N/m)
⎞
⎟ = 2.4 × 10 −3 m = 2.4 mm
⎟
⎠
⎛ 1 kg ⋅ m/s 2 ⎞
⎟ = 4.1× 10 −3 m = 4.1 mm
⎜
⎟
⎜
1
N
(2700 kg/m )(9.81 m/s ) ⎝
⎠
Discussion
Note that the ball diameter is inversely proportional to the square root of density, and thus for a given
material, the smaller balls are more likely to float.
D Al =
6σ s
=
ρg
6(0.073 N/m)
3
2
Review Problems
2-66
Solution
The pressure in an automobile tire increases during a trip while its volume remains constant. The percent
increase in the absolute temperature of the air in the tire is to be determined.
Assumptions
1 The volume of the tire remains constant. 2 Air is an ideal gas.
Analysis
the trip are
Noting that air is an ideal gas and the volume is constant, the ratio of absolute temperatures after and before
P1V1 P2V 2
T
P
310 kPa
= 1.069
=
→ 2 = 2 =
T1
T2
T1
P1 290 kPa
Therefore, the absolute temperature of air in the tire will increase by 6.9% during this trip.
Discussion
This may not seem like a large temperature increase, but if the tire is originally at 20oC (293.15 K), the
temperature increases to 1.069(293.15 K) = 313.38 K or about 40.2oC.
2-30
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-67
Solution
A large tank contains nitrogen at a specified temperature and pressure. Now some nitrogen is allowed to
escape, and the temperature and pressure of nitrogen drop to new values. The amount of nitrogen that has escaped is to be
determined.
Assumptions
Analysis
The tank is insulated so that no heat is transferred.
Treating N2 as an ideal gas, the initial and the final masses in the tank are determined to be
(800kPa)(20m 3 )
PV
m1 = 1 =
= 180.9 kg
RT1 (0.2968kPa ⋅ m 3 /kg ⋅ K)(298K)
(600kPa)(20m 3 )
PV
m2 = 2 =
= 138.0 kg
RT2 (0.2968kPa ⋅ m 3 /kg ⋅ K)(293K)
N2
800 kPa
25°C
3
20 m
Thus the amount of N2 that escaped is Δm = m1 − m2 = 180.9 − 138.0 = 42.9 kg
Discussion
refrigeration.
Gas expansion generally causes the temperature to drop. This principle is used in some types of
2-68
Solution
Suspended solid particles in water are considered. A relation is to be developed for the specific gravity of
the suspension in terms of the mass fraction Cs , mass and volume fraction Cs , vol of the particles.
Assumptions 1 The solid particles are distributed uniformly in water so that the solution is homogeneous. 2 The effect of
dissimilar molecules on each other is negligible.
Analysis
Consider solid particles of mass ms and volume Vs dissolved in a fluid of mass mf and volume Vm. The total
volume of the suspension (or mixture) is
V m = V s +V f
Dividing by Vm and using the definition Cs, vol = V s / V m give
1 = C s ,vol +
Vf
Vm
→
Vf
Vm
= 1− C s ,vol
(1)
The total mass of the suspension (or mixture) is
mm = ms + m f
Dividing by mm and using the definition C s, mass = m s / mm give
1 = C s ,mass +
mf
mm
= C s ,mass +
ρ fV f
ρ mV m
→
ρf
ρm
= (1 − C s ,mass )
Vm
Vf
(2)
Combining equations 1 and 2 gives
ρ f 1 − C s ,mass
=
1 − C s ,vol
ρm
When the fluid is water, the ratio ρ f / ρ m is the inverse of the definition of specific gravity. Therefore, the desired relation
for the specific gravity of the mixture is
SG m =
ρ m 1 − Cs ,vol
=
ρ f 1 − Cs ,mass
which is the desired result.
Discussion
As a quick check, if there were no particles at all, SGm = 0, as expected.
2-31
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-69
Solution
The specific gravities of solid particles and carrier fluids of a slurry are given. The relation for the specific
gravity of the slurry is to be obtained in terms of the mass fraction Cs , mass and the specific gravity SGs of solid particles.
Assumptions 1 The solid particles are distributed uniformly in water so that the solution is homogeneous. 2 The effect of
dissimilar molecules on each other is negligible.
Analysis
Consider solid particles of mass ms and volume Vs dissolved in a fluid of mass mf and volume Vm. The total
volume of the suspension (or mixture) is V m = V s +V f .
Dividing by Vm gives
1=
Vs V f
→
+
Vm Vm
Vf
Vm
= 1−
Vs
SG m
m / ρs
m ρ
= 1− s
= 1 − s m = 1 − Cs ,mass
Vm
SG s
mm / ρ m
mm ρ s
(1)
since ratio of densities is equal two the ratio of specific gravities, and m s / mm = C s, mass . The total mass of the suspension
(or mixture) is mm = m s + m f . Dividing by mm and using the definition C s, mass = m s / mm give
1 = Cs ,mass +
mf
mm
= Cs ,mass +
ρ fVf
ρ mVm
→
Vf
ρm
=
ρ f (1 − C s ,mass )V m
(2)
Taking the fluid to be water so that ρm / ρ f = SG m and combining equations 1 and 2 give
SG m =
1 − Cs ,mass SG m / SG s
1 − Cs ,mass
Solving for SGm and rearranging gives
SG m =
1
1 + Cs, mass ( 1 SG s −1)
which is the desired result.
Discussion
As a quick check, if there were no particles at all, SGm = 0, as expected.
2-70E
Solution
The minimum pressure on the suction side of a water pump is given. The maximum water temperature to
avoid the danger of cavitation is to be determined.
Properties
The saturation temperature of water at 0.95 psia is 100°F.
Analysis
To avoid cavitation at a specified pressure, the fluid temperature everywhere in the flow should remain
below the saturation temperature at the given pressure, which is
Tmax = Tsat @ 0.95 psia = 100°F
Therefore, T must remain below 100°F to avoid the possibility of cavitation.
Discussion
Note that saturation temperature increases with pressure, and thus cavitation may occur at higher pressure at
locations with higher fluid temperatures.
2-32
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-71
Solution
determined.
Air in a partially filled closed water tank is evacuated. The absolute pressure in the evacuated space is to be
Properties
The saturation pressure of water at 60°C is 19.94 kPa.
Analysis
When air is completely evacuated, the vacated space is filled with water vapor, and the tank contains a
saturated water-vapor mixture at the given pressure. Since we have a two-phase mixture of a pure substance at a specified
temperature, the vapor pressure must be the saturation pressure at this temperature. That is,
Pv = Psat @ 60°C = 19.94 kPa ≅ 19.9 kPa
Discussion
If there is any air left in the container, the vapor pressure will be less. In that case the sum of the component
pressures of vapor and air would equal 19.94 kPa.
2-72
Solution
The variation of the dynamic viscosity of water with absolute temperature is given. Using tabular data, a
relation is to be obtained for viscosity as a 4th-order polynomial. The result is to be compared to Andrade’s equation in the
form of μ = D ⋅ e B / T .
The viscosity data are given in tabular form as
T (K)
273.15
278.15
283.15
293.15
303.15
313.15
333.15
353.15
373.15
μ (Pa⋅s)
0.0018
1.787×10
1.519×10-3
1.307×10-3
1.002×10-3
7.975×10-4
6.529×10-4
4.665×10-4
3.547×10-4
2.828×10-4
-3
0.0016
0.0014
0.0012
μ
Properties
0.001
0.0008
0.0006
Analysis Using EES, (1) Define a trivial
0.0004
function “a=mu+T” in the equation window, (2)
select new parametric table from Tables, and
0.0002
type the data in a two-column table, (3) select
270
292
314
Plot and plot the data, and (4) select plot and
T
click on “curve fit” to get curve fit window.
Then specify polynomial and enter/edit equation. The equations and plot are shown here.
336
358
380
μ = 0.489291758 - 0.00568904387T + 0.0000249152104T2 - 4.86155745×10-8T3 + 3.56198079×10-11T4
μ = 0.000001475*EXP(1926.5/T) [used initial guess of a0=1.8×10-6 and a1=1800 in mu=a0*exp(a1/T)]
At T = 323.15 K, the polynomial and exponential curve fits give
Polynomial: μ(323.15 K) = 0.0005529 Pa⋅s
(1.1% error, relative to 0.0005468 Pa⋅s)
(4.7% error, relative to 0.0005468 Pa⋅s)
Exponential: μ(323.15 K) = 0.0005726 Pa⋅s
Discussion
This problem can also be solved using an Excel worksheet, with the following results:
Polynomial:
A = 0.4893, B = -0.005689, C = 0.00002492, D = -0.000000048612, and E = 0.00000000003562
1864.06 T
Andrade’s equation: μ = 1.807952 E − 6* e
2-33
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-73
Solution
The velocity profile for laminar one-dimensional flow between two parallel plates is given. A relation for
friction drag force exerted on the plates per unit area of the plates is to be obtained.
[
u ( y ) = 4u max y h − ( y h )2
Assumptions 1 The flow between the plates is one-dimensional. 2 The
fluid is Newtonian.
[
The velocity profile is given by u ( y ) = 4u max y h − ( y h )2
Analysis
]
where h is the distance between the two plates, y is the vertical distance
from the bottom plate, and umax is the maximum flow velocity that occurs at
midplane. The shear stress at the bottom surface can be expressed as
τw
du
=μ
dy
= 4 μu max
y =0
d ⎛ y y2 ⎞
⎛ 1 2y ⎞
⎟
⎜ −
= 4 μu max ⎜ − 2 ⎟
2 ⎟
⎜
dy ⎝ h h ⎠ y =0
⎝h h ⎠
y =0
4 μu max
=
h
h
umax
y
0
Because of symmetry, the wall shear stress is identical at both bottom and top plates. Then the friction drag force exerted by
the fluid on the inner surface of the plates becomes
8μu max
Aplate
FD = 2τ w A plate =
h
Therefore, the friction drag per unit plate area is
8μu max
FD / Aplate =
h
Discussion
Note that the friction drag force acting on the plates is inversely proportional to the distance between plates.
2-74
Solution
The laminar flow of a Bingham plastic fluid in a horizontal pipe
of radius R is considered. The shear stress at the pipe wall and the friction drag
force acting on a pipe section of length L are to be determined.
Assumptions
R
r
1 The fluid is a Bingham plastic with τ = τ y + μ (du dr ) where
τy is the yield stress. 2 The flow through the pipe is one-dimensional.
0
u(r)
τy
ΔP 2
(r − R 2 ) +
(r − R ) where ΔP/L is the pressure drop along
4 μL
μ
the pipe per unit length, μ is the dynamic viscosity, r is the radial distance from the centerline. Its gradient at the pipe wall
(r = R) is
The velocity profile is given by u (r ) =
Analysis
du
dr
=
r =R
τy
⎞
d ⎛ ΔP 2
⎜⎜
(r − R 2 ) +
(r − R ) ⎟⎟
dr ⎝ 4 μL
μ
⎠
r=R
⎛
ΔP τ y
= ⎜⎜ 2r
+
⎝ 4 μL μ
⎞
1 ΔP
⎟⎟
= ⎛⎜
R + τ y ⎞⎟
⎠
⎠ r =R μ ⎝ 2L
Substituing into τ = τ y + μ (du dr ) , the wall shear stress at the pipe surface becomes
τw =τ y + μ
du
dr
r=R
=τ y +
ΔP
ΔP
R + τ y = 2τ y +
R
2L
2L
Then the friction drag force exerted by the fluid on the inner surface of the pipe becomes
ΔP ⎞
ΔP ⎞
⎛
⎛
FD = τ w As = ⎜ 2τ y +
R ⎟( 2πRL ) = 2πRL⎜ 2τ y +
R ⎟ = 4πRLτ y + πR 2 ΔP
2L ⎠
2L ⎠
⎝
⎝
Discussion
Note that the total friction drag is proportional to yield shear stress and the pressure drop.
2-34
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
]
Chapter 2 Properties of Fluids
2-75
Solution
A circular disk immersed in oil is used as a damper, as shown in the figure. It is to be shown that the
damping torque is Tdamping = Cω where C = 0.5πμ(1 a + 1 b )R 4 .
Assumptions 1 The thickness of the oil layer on each
side remains constant. 2 The velocity profiles are linear
on both sides of the disk. 3 The tip effects are negligible.
4 The effect of the shaft is negligible.
R
Analysis
The velocity gradient anywhere in the oil
of film thickness a is V/a where V = ωr is the tangential
velocity. Then the wall shear stress anywhere on the
upper surface of the disk at a distance r from the axis of
rotation can be expressed as
y
a
b
du
V
ωr
τw = μ
=μ =μ
dy
a
a
Then the shear force acting on a differential area dA on
the surface and the torque it generates can be expressed as
ωr
dA
dF = τ w dA = μ
a
ωr 2
dA
dT = rdF = μ
a
Noting that dA = 2πrdr and integrating, the torque on the top surface is determined to be
Ttop =
μω
a
∫
r 2 dA =
A
μω
a
∫
R
r =0
r 2 (2πr )dr =
2πμω
a
∫
R
r =0
r 3 dr =
2πμω r 4
4
a
R
=
r =0
Disk
Damping oil
πμωR 4
2a
The torque on the bottom surface is obtained by replaying a by b,
πμωR 4
Tbottom =
2b
The total torque acting on the disk is the sum of the torques acting on the top and bottom surfaces,
πμωR 4 ⎛ 1 1 ⎞
Tdamping, total = Tbottom + Ttop =
⎜ + ⎟
2 ⎝a b⎠
or,
πμR 4 ⎛ 1 1 ⎞
Tdamping, total = Cω where C =
⎜ + ⎟
2 ⎝a b⎠
This completes the proof.
Discussion
Note that the damping torque (and thus damping power) is inversely proportional to the thickness of oil
films on either side, and it is proportional to the 4th power of the radius of the damper disk.
2-35
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-76E
Solution
A glass tube is inserted into mercury. The capillary drop of mercury in the tube is to be determined.
Assumptions 1 There are no impurities in mercury, and no contamination on the surfaces of the glass tube. 2 The mercury
is open to the atmospheric air.
Properties
The surface tension of mercury-glass in atmospheric air at 68°F (20°C) is σs = 0.440×0.06852 = 0.03015
lbf/ft. The density of mercury is ρ = 847 lbm/ft3 at 77°F, but we can also use this value at 68°F. The contact angle is given
to be 140°.
Substituting the numerical values, the capillary drop is determined to be
Analysis
2 ( 0.03015 lbf/ft )( cos140° )
⎛ 32.2 lbm ⋅ ft/s 2 ⎞
2σ cosφ
h= s
=
ρ gR
(847 lbm/ft 3 )( 32.2 ft/s2 ) ( 0.45 / 12 ft ) ⎜⎝ 1 lbf ⎟⎠
Air
Mercury
h
= −0.00145 ft = -0.0175 in
Discussion
The negative sign indicates capillary drop instead of rise. The drop is
very small in this case because of the large diameter of the tube.
2-77
Solution
A relation is to be derived for the capillary rise of a liquid between two large parallel plates a distance t
apart inserted into a liquid vertically. The contact angle is given to be φ.
Assumptions
There are no impurities in the liquid, and no contamination on the surfaces of the plates.
Analysis
The magnitude of the capillary rise between two large parallel plates can be determined from a force
balance on the rectangular liquid column of height h and width w between the plates. The bottom of the liquid column is at
the same level as the free surface of the liquid reservoir, and thus the pressure there must be atmospheric pressure. This will
balance the atmospheric pressure acting from the top surface, and thus these two effects will cancel each other. The weight
of the liquid column is
t
W = mg = ρgV = ρg (w × t × h)
Equating the vertical component of the surface tension force to the weight gives
W = Fsurface
→
ρg ( w × t × h) = 2wσ s cos φ
Canceling w and solving for h gives the capillary rise to be
Capillary rise:
h=
h
Air
Liquid
2σ s cos φ
ρgt
W
Discussion
The relation above is also valid for non-wetting liquids (such as mercury in glass), and gives a capillary
drop instead of a capillary rise.
2-36
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 2 Properties of Fluids
2-78
Solution
A journal bearing is lubricated with oil whose viscosity is
known. The torques needed to overcome the bearing friction during start-up
and steady operation are to be determined.
Assumptions 1 The gap is uniform, and is completely filled with oil. 2 The
end effects on the sides of the bearing are negligible. 3 The fluid is
Newtonian.
Properties
The viscosity of oil is given to be 0.1 kg/m⋅s at 20°C, and
0.008 kg/m⋅s at 80°C.
Analysis
The radius of the shaft is R = 0.04 m. Substituting the given
values, the torque is determined to be
R
l = 0.08 cm
fluid
At start up at 20°C:
4π 2 (0.04 m) 3 (500 / 60 s -1 )(0.30 m)
4π 2 R 3 n L
T=μ
= (0.1 kg/m ⋅ s)
= 0.79 N ⋅ m
0.0008 m
A
During steady operation at 80°C:
4π 2 (0.04 m) 3 (500 / 60 s -1 )(0.30 m)
4π 2 R 3 n L
= (0.008 kg/m ⋅ s)
= 0.063 N ⋅ m
T=μ
0.0008 m
A
Discussion
Note that the torque needed to overcome friction reduces considerably due to the decrease in the viscosity
of oil at higher temperature.
Design and Essay Problems
2-79 to 2-81
Solution
Students’ essays and designs should be unique and will differ from each other.
KJ
2-37
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications
by Çengel & Cimbala
CHAPTER 3
PRESSURE AND FLUID STATICS
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of The McGraw-Hill Companies, Inc.
(“McGraw-Hill”) and protected by copyright and other state and federal laws. By
opening and using this Manual the user agrees to the following restrictions, and if the
recipient does not agree to these restrictions, the Manual should be promptly returned
unopened to McGraw-Hill: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated
textbook. No other use or distribution of this Manual is permitted. This Manual
may not be sold and may not be distributed to or used by any student or other
third party. No part of this Manual may be reproduced, displayed or distributed
in any form or by any means, electronic or otherwise, without the prior written
permission of McGraw-Hill.
3-1
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
Pressure, Manometer, and Barometer
3-1C
Solution
We are to discuss the difference between gage pressure and absolute pressure.
Analysis
The pressure relative to the atmospheric pressure is called the gage pressure, and the pressure relative
to an absolute vacuum is called absolute pressure.
Discussion
Most pressure gages (like your bicycle tire gage) read relative to atmospheric pressure, and therefore read
the gage pressure.
3-2C
Solution
We are to explain nose bleeding and shortness of breath at high elevation.
Analysis
Atmospheric air pressure which is the external pressure exerted on the skin decreases with increasing
elevation. Therefore, the pressure is lower at higher elevations. As a result, the difference between the blood pressure
in the veins and the air pressure outside increases. This pressure imbalance may cause some thin-walled veins such
as the ones in the nose to burst, causing bleeding. The shortness of breath is caused by the lower air density at higher
elevations, and thus lower amount of oxygen per unit volume.
Discussion
People who climb high mountains like Mt. Everest suffer other physical problems due to the low pressure.
3-3C
Solution
We are to examine a claim about absolute pressure.
Analysis
No, the absolute pressure in a liquid of constant density does not double when the depth is doubled. It
is the gage pressure that doubles when the depth is doubled.
Discussion
This is analogous to temperature scales – when performing analysis using something like the ideal gas law,
you must use absolute temperature (K), not relative temperature (oC), or you will run into the same kind of problem.
3-4C
Solution
We are to compare the pressure on the surfaces of a cube.
Analysis
Since pressure increases with depth, the pressure on the bottom face of the cube is higher than that on
the top. The pressure varies linearly along the side faces. However, if the lengths of the sides of the tiny cube suspended
in water by a string are very small, the magnitudes of the pressures on all sides of the cube are nearly the same.
Discussion
In the limit of an “infinitesimal cube”, we have a fluid particle, with pressure P defined at a “point”.
3-5C
Solution
We are to define Pascal’s law and give an example.
Analysis
Pascal’s law states that the pressure applied to a confined fluid increases the pressure throughout by
the same amount. This is a consequence of the pressure in a fluid remaining constant in the horizontal direction. An
example of Pascal’s principle is the operation of the hydraulic car jack.
Discussion
The above discussion applies to fluids at rest (hydrostatics). When fluids are in motion, Pascal’s principle
does not necessarily apply. However, as we shall see in later chapters, the differential equations of incompressible fluid
flow contain only pressure gradients, and thus an increase in pressure in the whole system does not affect fluid motion.
3-2
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-6C
Solution
We are to compare the volume and mass flow rates of two fans at different elevations.
Analysis
The density of air at sea level is higher than the density of air on top of a high mountain. Therefore, the
volume flow rates of the two fans running at identical speeds will be the same, but the mass flow rate of the fan at sea level
will be higher.
Discussion
In reality, the fan blades on the high mountain would experience less frictional drag, and hence the fan
motor would not have as much resistance – the rotational speed of the fan on the mountain would be slightly higher than
that at sea level.
3-7
Solution
The pressure in a vacuum chamber is measured by a vacuum gage. The
absolute pressure in the chamber is to be determined.
24 kPa
Pabs
The absolute pressure in the chamber is determined from
Analysis
Pabs = Patm − Pvac = 92 − 24 = 68 kPa
Discussion
Patm = 92 kPa
We must remember that “vacuum pressure” is the negative of gage pressure – hence the negative sign.
3-8E
Solution
The pressure in a tank is measured with a manometer by measuring the differential height of the manometer
fluid. The absolute pressure in the tank is to be determined for two cases: the manometer arm with the (a) higher and (b)
lower fluid level being attached to the tank.
Assumptions
The fluid in the manometer is incompressible.
Properties
The specific gravity of the fluid is given to be SG = 1.25. The density of water at 32°F is 62.4 lbm/ft3.
Analysis
The density of the fluid is obtained by multiplying its specific gravity by the density of water,
ρ = SG × ρ H O = (1.25)(62.4 lbm/ft 3 ) = 78.0 lbm/ft 3
2
The pressure difference corresponding to a differential height of 28 in between the two arms of the manometer is
⎛
1lbf
ΔP = ρgh = (78 lbm/ft 3 )(32.174 ft/s 2 )(28/12 ft)⎜
⎜ 32.174 lbm ⋅ ft/s 2
⎝
Then the absolute pressures in the tank for the two cases become:
⎞⎛ 1ft 2
⎟⎜
⎟⎜ 144 in 2
⎠⎝
⎞
⎟ = 1.26 psia
⎟
⎠
Patm
(a) The fluid level in the arm attached to the tank is higher (vacuum):
Pabs = Patm − Pvac = 12.7 − 1.26 = 11.44 psia ≅ 11.4 psia
Air
28 in
SG= 1.25
(b) The fluid level in the arm attached to the tank is lower:
Pabs = Pgage + Patm = 12.7 + 1.26 = 13.96 psia ≅ 14.0 psia
Discussion
The final results are reported to three significant digits. Note
that we can determine whether the pressure in a tank is above or below
atmospheric pressure by simply observing the side of the manometer arm
with the higher fluid level.
3-3
Patm = 12.7 psia
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-9
Solution
The pressure in a pressurized water tank is measured by a multi-fluid manometer. The gage pressure of air
in the tank is to be determined.
Assumptions The air pressure in the tank is uniform (i.e., its variation with elevation is negligible due to its low density),
and thus we can determine the pressure at the air-water interface.
The densities of mercury, water, and oil are given to be 13,600, 1000, and 850 kg/m3, respectively.
Properties
Analysis
Starting with the pressure at point 1 at the air-water interface, and moving along the tube by adding (as we
go down) or subtracting (as we go up) the ρgh terms until we reach point 2, and setting the result equal to Patm since the
tube is open to the atmosphere gives
P1 + ρ water gh1 + ρ oil gh2 − ρ mercury gh3 = Patm
Air
1
Solving for P1,
P1 = Patm − ρ water gh1 − ρ oil gh2 + ρ mercury gh3
or,
h1
P1 − Patm = g ( ρ mercury h3 − ρ water h1 − ρ oil h2 )
h3
Noting that P1,gage = P1 - Patm and substituting,
Water
h2
P1, gage = (9.81 m/s 2 )[(13,600 kg/m 3 )(0.46 m) − (1000 kg/m 3 )(0.2 m)
⎛
1N
- (850 kg/m 3 )(0.3 m)]⎜
⎜ 1 kg ⋅ m/s 2
⎝
= 56.9 kPa
⎞⎛ 1 kPa ⎞
⎟⎜
⎟⎝ 1000 N/m 2 ⎟⎠
⎠
Discussion
Note that jumping horizontally from one tube to the next and realizing that pressure remains the same in the
same fluid simplifies the analysis greatly.
3-10
Solution
The barometric reading at a location is given in height of mercury column. The atmospheric pressure is to
be determined.
Properties
The density of mercury is given to be 13,600 kg/m3.
Analysis
The atmospheric pressure is determined directly from
⎛ 1N
⎞ ⎛ 1 kPa ⎞
Patm = ρ gh = (13,600 kg/m3 )( 9.81 m/s 2 ) ( 0.750 m ) ⎜
2 ⎟⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠ ⎝ 1000 N/m ⎠
= 100.1 kPa ≅ 100 kPa
Discussion
We round off the final answer to three significant digits. 100 kPa is a fairly typical value of atmospheric
pressure on land slightly above sea level.
3-4
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-11
Solution
The gage pressure in a liquid at a certain depth is given. The gage pressure in the same liquid at a different
depth is to be determined.
Assumptions
The variation of the density of the liquid with depth is negligible.
Analysis
The gage pressure at two different depths of a liquid can be expressed as P1 = ρgh1 and P2 = ρgh2 .
Taking their ratio,
P2 ρgh2 h2
=
=
ρgh1 h1
P1
h1
Solving for P2 and substituting gives
1
P2 =
h2
h2
12 m
(28 kPa) = 112 kPa
P1 =
3m
h1
2
Note that the gage pressure in a given fluid is proportional to depth.
Discussion
3-12
Solution
The absolute pressure in water at a specified depth is given. The local atmospheric pressure and the
absolute pressure at the same depth in a different liquid are to be determined.
Assumptions
The liquid and water are incompressible.
Properties
The specific gravity of the fluid is given to be SG = 0.85. We take the density of water to be 1000 kg/m3.
Then density of the liquid is obtained by multiplying its specific gravity by the density of water,
ρ = SG × ρ H 2O = (0.85)(1000 kg/m 3 ) = 850 kg/m 3
(a) Knowing the absolute pressure, the atmospheric pressure can be determined from
Analysis
Patm = P − ρ gh
⎛ 1 kPa ⎞
= (145 kPa) − (1000 kg/m 3 )(9.81 m/s 2 )(5 m) ⎜
= 96.0 kPa
2 ⎟
⎝ 1000 N/m ⎠
(b) The absolute pressure at a depth of 5 m in the other liquid is
Patm
h
P
P = Patm + ρ gh
⎛ 1 kPa ⎞
= (96.0 kPa) + (850 kg/m3 )(9.81 m/s 2 )(5 m) ⎜
2 ⎟
⎝ 1000 N/m ⎠
= 137.7 kPa ≅ 138 kPa
Discussion
Note that at a given depth, the pressure in the lighter fluid is lower, as expected.
3-13E
Solution
It is to be shown that 1 kgf/cm2 = 14.223 psi.
Analysis
Noting that 1 kgf = 9.80665 N, 1 N = 0.22481 lbf, and 1 in = 2.54 cm, we have
⎛ 0.22481 lbf
1 kgf = 9.80665 N = (9.80665 N )⎜⎜
1N
⎝
⎞
⎟⎟ = 2.20463 lbf
⎠
2
⎛ 2.54 cm ⎞
⎟⎟ = 14.223 lbf/in 2 = 14.223 psi
1 kgf/cm 2 = 2.20463 lbf/cm 2 = (2.20463 lbf/cm 2 )⎜⎜
1
in
⎝
⎠
Discussion
This relationship may be used as a conversion factor.
and
3-5
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-14E
Solution
The weight and the foot imprint area of a person are given. The pressures this man exerts on the ground
when he stands on one and on both feet are to be determined.
Assumptions
The weight of the person is distributed uniformly on foot imprint area.
Analysis
The weight of the man is given to be 200 lbf. Noting that
pressure is force per unit area, the pressure this man exerts on the ground is
(a) On one foot:
(a) On both feet:
Discussion
both feet.
W 200 lbf
=
= 5.56 lbf/in 2 = 5.56 psi
A 36 in 2
W
200 lbf
=
= 2.78 lbf/in 2 = 2.78 psi
P=
2 A 2 × 36 in 2
P=
Note that the pressure exerted on the ground (and on the feet) is reduced by half when the person stands on
3-15
Solution
The mass of a woman is given. The minimum imprint area per shoe needed to enable her to walk on the
snow without sinking is to be determined.
Assumptions 1 The weight of the person is distributed uniformly on the imprint area of the shoes. 2 One foot carries the
entire weight of a person during walking, and the shoe is sized for walking conditions (rather than standing). 3 The weight
of the shoes is negligible.
Analysis
The mass of the woman is given to be 70 kg. For a pressure of 0.5 kPa on the
snow, the imprint area of one shoe must be
A=
W mg (70 kg)(9.81 m/s 2 ) ⎛⎜
1N
=
=
2
⎜
P
P
0.5 kPa
⎝ 1 kg ⋅ m/s
⎞⎛ 1 kPa ⎞
⎟⎜
⎟ = 1.37 m 2
⎟⎝ 1000 N/m 2 ⎠
⎠
Discussion
This is a very large area for a shoe, and such shoes would be impractical to use. Therefore, some sinking of
the snow should be allowed to have shoes of reasonable size.
3-16
Solution
The vacuum pressure reading of a tank is given. The absolute pressure in the tank is to be determined.
Properties
The density of mercury is given to be ρ = 13,590 kg/m3.
Analysis
The atmospheric (or barometric) pressure can be expressed as
Patm = ρ g h
⎛
1N
= (13,590 kg/m 3 )(9.807 m/s 2 )(0.755 m)⎜⎜
2
⎝ 1 kg ⋅ m/s
= 100.6 kPa
⎞⎛ 1 kPa
⎟⎜
⎟⎜ 1000 N/m 2
⎠⎝
Pabs
⎞
⎟
⎟
⎠
30kPa
Patm = 755mmHg
Then the absolute pressure in the tank becomes
Pabs = Patm − Pvac = 100.6 − 30 = 70.6 kPa
Discussion
The gage pressure in the tank is the negative of the vacuum pressure, i.e., Pgage = −30.0 kPa.
3-6
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-17E
Solution
A pressure gage connected to a tank reads 50 psi. The absolute pressure in the tank is to be determined.
Properties
The density of mercury is given to be ρ = 848.4 lbm/ft3.
Analysis
The atmospheric (or barometric) pressure can be expressed as
Pabs
Patm = ρ g h
50 psia
⎛
⎞ ⎛ 1 ft 2 ⎞
1 lbf
= (848.4 lbm/ft 3 )(32.174 ft/s 2 )(29.1/12 ft) ⎜
⎟
2 ⎜
2 ⎟
⎝ 32.174 lbm ⋅ ft/s ⎠⎝ 144 in ⎠
= 14.29 psia
Then the absolute pressure in the tank is
Pabs = Pgage + Patm = 50 + 14.29 = 64.29 psia ≅ 64.3 psia
Discussion
This pressure is more than four times as much as standard atmospheric pressure.
3-18
Solution
A pressure gage connected to a tank reads 500 kPa. The absolute pressure
in the tank is to be determined.
The absolute pressure in the tank is determined from
Analysis
Pabs = Pgage + Patm = 500 + 94 = 594 kPa
Discussion
500 kPa
Pabs
Patm = 94 kPa
This pressure is almost six times greater than standard atmospheric pressure.
3-19
Solution
A mountain hiker records the barometric reading before and after a hiking trip. The vertical distance
climbed is to be determined.
Assumptions The variation of air density and the gravitational acceleration with
altitude is negligible.
Properties
The density of air is given to be ρ = 1.20 kg/m .
780 mbar
3
h=?
Analysis
Taking an air column between the top and the bottom of the mountain
and writing a force balance per unit base area, we obtain
Wair / A = Pbottom − Ptop
930 mbar
( ρgh) air = Pbottom − Ptop
⎛
1N
(1.20 kg/m 3 )(9.81 m/s 2 )(h)⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞⎛
1 bar
⎟⎜
⎟⎜ 100,000 N/m 2
⎠⎝
⎞
⎟ = (0.930 − 0.780) bar
⎟
⎠
It yields h = 1274 m ≅ 1270 m (to 3 significant digits), which is also the distance climbed.
Discussion
A similar principle is used in some aircraft instruments to measure elevation.
3-7
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-20
Solution
A barometer is used to measure the height of a building by recording reading at the bottom and at the top of
the building. The height of the building is to be determined.
Assumptions
The variation of air density with altitude is negligible.
Properties
The density of air is given to be ρ = 1.18 kg/m3. The density of mercury is 13,600 kg/m3.
Analysis
Atmospheric pressures at the top and at the bottom of the building are
730 mmHg
Ptop = (ρ g h) top
Pbottom
⎛
⎞⎛ 1 kPa ⎞
1 N
= (13,600 kg/m3 )(9.807 m/s 2 )(0.730 m) ⎜
2 ⎟⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠⎝ 1000 N/m ⎠
= 97.36 kPa
= ( ρ g h )bottom
⎛ 1N
⎞⎛ 1 kPa ⎞
= (13,600 kg/m3 )(9.807 m/s 2 )(0.755 m) ⎜
2 ⎟⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠⎝ 1000 N/m ⎠
= 100.70 kPa
h
755 mmHg
Taking an air column between the top and the bottom of the building, we write a force balance per unit base area,
Wair / A = Pbottom − Ptop
( ρ gh )air = Pbottom − Ptop
and
⎛ 1 N
⎞⎛ 1 kPa ⎞
(1.18 kg/m3 )(9.807 m/s 2 )(h) ⎜
= (100.70 − 97.36) kPa
2 ⎟⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠⎝ 1000 N/m ⎠
which yields h = 288.6 m ≅ 289 m, which is also the height of the building.
Discussion
There are more accurate ways to measure the height of a building, but this method is quite simple.
3-21
Solution
The previous problem is reconsidered. The EES solution is to be printed out, including proper units.
Analysis
The EES Equations window is printed below, followed by the Solution window.
P_bottom=755"[mmHg]"
P_top=730"[mmHg]"
g=9.807 "[m/s^2]" "local acceleration of gravity at sea level"
rho=1.18"[kg/m^3]"
DELTAP_abs=(P_bottom-P_top)*CONVERT('mmHg','kPa')"[kPa]" "Delta P reading from the
barometers, converted from mmHg to kPa."
DELTAP_h =rho*g*h/1000 "[kPa]"
"Equ. 1-16. Delta P due to the air fluid column height, h,
between the top and bottom of the building."
"Instead of dividing by 1000 Pa/kPa we could have multiplied rho*g*h by the EES function,
CONVERT('Pa','kPa')"
DELTAP_abs=DELTAP_h
SOLUTION
Variables in Main
DELTAP_abs=3.333 [kPa]
g=9.807 [m/s^2]
P_bottom=755 [mmHg]
rho=1.18 [kg/m^3]
Discussion
DELTAP_h=3.333 [kPa]
h=288 [m]
P_top=730 [mmHg]
To obtain the solution in EES, simply click on the icon that looks like a calculator, or Calculate-Solve.
3-8
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-22
Solution
A diver is moving at a specified depth from the water surface. The pressure exerted on the surface of the
diver by the water is to be determined.
Assumptions
The variation of the density of water with depth is negligible.
Properties
The specific gravity of sea water is given to be SG = 1.03. We take the density of water to be 1000 kg/m3.
Analysis
The density of the sea water is obtained by multiplying its specific gravity
by the density of water which is taken to be 1000 kg/m3:
Patm
ρ = SG × ρ H O = (1.03)(1000 kg/m3 ) = 1030 kg/m3
Sea
2
h
The pressure exerted on a diver at 30 m below the free surface of the sea is
the absolute pressure at that location:
P
P = Patm + ρ gh
⎛ 1 kPa ⎞
= (101 kPa) + (1030 kg/m3 )(9.807 m/s 2 )(30 m) ⎜
2 ⎟
⎝ 1000 N/m ⎠
= 404 kPa
Discussion
This is about 4 times the normal sea level value of atmospheric pressure.
3-23E
Solution
A submarine is cruising at a specified depth from the water
surface. The pressure exerted on the surface of the submarine by water is to be
determined.
Assumptions
Patm
Sea
The variation of the density of water with depth is negligible.
Properties
The specific gravity of sea water is given to be SG = 1.03. The
density of water at 32°F is 62.4 lbm/ft3.
h
P
Analysis
The density of the seawater is obtained by multiplying its specific
gravity by the density of water,
ρ = SG × ρ H 2O = (1.03)(62.4 lbm/ft 3 ) = 64.27 lbm/ft 3
The pressure exerted on the surface of the submarine cruising 300 ft below the free surface of the sea is the absolute
pressure at that location:
P = Patm + ρ gh
⎛
⎞ ⎛ 1 ft 2 ⎞
1 lbf
= (14.7 psia) + (64.27 lbm/ft 3 )(32.174 ft/s 2 )(300 ft) ⎜
2 ⎟⎜
2 ⎟
⎝ 32.174 lbm ⋅ ft/s ⎠⎝ 144 in ⎠
= 148.6 psia ≅ 149 psia
where we have rounded the final answer to three significant digits.
Discussion
This is more than 10 times the value of atmospheric pressure at sea level.
3-9
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-24
Solution
A gas contained in a vertical piston-cylinder device is pressurized by a spring and by the weight of the
piston. The pressure of the gas is to be determined.
Fspring
Analysis
Drawing the free body diagram of the piston and balancing the vertical forces yields
PA = Patm A + W + Fspring
Thus,
P = Patm +
Patm
mg + Fspring
A
(4 kg)(9.807 m/s 2 ) + 60 N ⎛ 1 kPa
= (95 kPa) +
⎜
2
35 × 10−4 m 2
⎝ 1000 N/m
Discussion
⎞
⎟ = 123.4 kPa ≅ 123 kPa
⎠
P
W = mg
This setup represents a crude but functional way to control the pressure in a tank.
3-25
Solution
The previous problem is reconsidered. The effect of the spring force in the range of 0 to 500 N on the
pressure inside the cylinder is to be investigated. The pressure against the spring force is to be plotted, and results are to be
discussed.
The EES Equations window is printed below, followed by the tabulated and plotted results.
Analysis
g=9.807"[m/s^2]"
P_atm= 95"[kPa]"
m_piston=4"[kg]"
{F_spring=60"[N]"}
A=35*CONVERT('cm^2','m^2')"[m^2]"
W_piston=m_piston*g"[N]"
F_atm=P_atm*A*CONVERT('kPa','N/m^2')"[N]"
"From the free body diagram of the piston, the balancing vertical forces yield:"
F_gas= F_atm+F_spring+W_piston"[N]"
P_gas=F_gas/A*CONVERT('N/m^2','kPa')"[kPa]"
260
Results:
Pgas [kPa]
0
55.56
111.1
166.7
222.2
277.8
333.3
388.9
444.4
500
106.2
122.1
138
153.8
169.7
185.6
201.4
217.3
233.2
249.1
Discussion
240
220
P gas [kPa]
Fspring [N]
200
180
160
140
120
100
0
100
200
300
F
[N]
spring
400
500
The relationship is linear, as expected.
3-10
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-26 [Also solved using EES on enclosed DVD]
Solution
Both a pressure gage and a manometer are attached to a tank of gas to measure its pressure. For a specified
reading of gage pressure, the difference between the fluid levels of the two arms of the manometer is to be determined for
mercury and water.
Properties
The densities of water and mercury are given to be ρwater = 1000 kg/m3 and be ρHg = 13,600 kg/m3.
Analysis
The gage pressure is related to the vertical distance h between the two fluid levels by
Pgage = ρ g h
⎯⎯
→
h=
Pgage
80 kPa
ρg
(a) For mercury,
AIR
⎛ 1 kN/m 2
⎜
=
h=
ρ Hg g (13600 kg/m 3 )(9.807 m/s 2 ) ⎜⎝ 1 kPa
Pgage
80 kPa
⎞⎛ 1000 kg/m ⋅ s 2
⎟⎜
⎟⎜
1 kN
⎠⎝
⎞
⎟ = 0.60 m
⎟
⎠
⎞⎛ 1000 kg/m ⋅ s 2
⎟⎜
⎟⎜
1 kN
⎠⎝
⎞
⎟ = 8.16 m
⎟
⎠
h
(b) For water,
h=
Pgage
ρ H 2O g
=
⎛ 1 kN/m 2
⎜
(1000 kg/m 3 )(9.807 m/s 2 ) ⎜⎝ 1 kPa
80 kPa
Discussion
The manometer with water is more precise since the column height is bigger (better resolution). However, a
column of water more than 8 meters high would be impractical, so mercury is the better choice of manometer fluid here.
3-11
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-27
Solution
The previous problem is reconsidered. The effect of the manometer fluid density in the range of 800 to
13,000 kg/m3 on the differential fluid height of the manometer is to be investigated. Differential fluid height is to be plotted
as a function of the density, and the results are to be discussed.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
Function fluid_density(Fluid$)
If fluid$='Mercury' then fluid_density=13600 else fluid_density=1000
end
{Input from the diagram window. If the diagram window is hidden, then all of the input must come from the
equations window. Also note that brackets can also denote comments - but these comments do not appear
in the formatted equations window.}
{Fluid$='Mercury'
P_atm = 101.325
DELTAP=80
"kpa"
"kPa Note how DELTAP is displayed on the Formatted Equations Window."}
g=9.807
"m/s2, local acceleration of gravity at sea level"
"Get the fluid density, either Hg or H2O, from the function"
rho=Fluid_density(Fluid$)
"To plot fluid height against density place {} around the above equation. Then set up the parametric table
and solve."
DELTAP = RHO*g*h/1000
"Instead of dividing by 1000 Pa/kPa we could have multiplied by the EES function, CONVERT('Pa','kPa')"
h_mm=h*convert('m','mm')
"The fluid height in mm is found using the built-in CONVERT function."
P_abs= P_atm + DELTAP
"To make the graph, hide the diagram window and remove the {}brackets from Fluid$ and from P_atm.
Select New Parametric Table from the Tables menu. Choose P_abs, DELTAP and h to be in the table.
Choose Alter Values from the Tables menu. Set values of h to range from 0 to 1 in steps of 0.2. Choose
Solve Table (or press F3) from the Calculate menu. Choose New Plot Window from the Plot menu.
Choose to plot P_abs vs h and then choose Overlay Plot from the Plot menu and plot DELTAP on the same
scale."
Tank Fluid Gage and Absolute Pressures vs Manom eter Fluid Height
Results:
ρ [kg/m3]
800
2156
3511
4867
6222
7578
8933
10289
11644
13000
220
Manometer Fluid: Mercury
200
Pressure, kPa
hmm [mm]
10197
3784
2323
1676
1311
1076
913.1
792.8
700.5
627.5
240
180
Absolute Pressure
160
140
120
100
Gage Pressure
80
60
40
20
0
0.00
0.20
0.40
0.60
0.80
1.00
M anom eter Fluid Height, m
3-12
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
Manom eter Fluid Height vs Manom eter Fluid Density
11000
8800
h mm [m m ]
6600
4400
2200
0
0
2000
4000
6000
8000
10000 12000 14000
ρ [kg/m ^3]
Discussion
Many comments are provided in the Equation window above to help you learn some of the features of EES.
3-28
Solution
The air pressure in a tank is measured by an oil manometer. For a
given oil-level difference between the two columns, the absolute pressure in the
tank is to be determined.
Properties
Analysis
The density of oil is given to be ρ = 850 kg/m3.
AIR
0.45 m
The absolute pressure in the tank is determined from
P = Patm + ρ gh
⎛ 1 kPa ⎞
= (98 kPa) + (850 kg/m3 )(9.81 m/s 2 )(0.45 m) ⎜
⎟
1000 N/m 2 ⎠
⎝
= 101.75 kPa ≅ 102 kPa
Patm = 98 kPa
Discussion
If a heavier liquid, such as water, were used for the manometer fluid, the column height would be smaller,
and thus the reading would be less precise (lower resolution).
3-13
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-29
Solution
The air pressure in a duct is measured by a mercury manometer. For a given mercury-level difference
between the two columns, the absolute pressure in the duct is to be determined.
Properties
The density of mercury is given to be ρ = 13,600 kg/m3.
Analysis
(a) The pressure in the duct is above atmospheric pressure since the fluid
column on the duct side is at a lower level.
(b) The absolute pressure in the duct is determined from
Air
15 mm
P
P = Patm + ρ gh
⎛ 1 N
⎞⎛ 1 kPa ⎞
= (100 kPa) + (13,600 kg/m3 )(9.81 m/s 2 )(0.015 m) ⎜
2 ⎟⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠⎝ 1000 N/m ⎠
= 102.00 kPa ≅ 102 kPa
Discussion
When measuring pressures in a fluid flow, the difference between two pressures is usually desired. In this
case, the difference is between the measurement point and atmospheric pressure.
3-30
Solution
The air pressure in a duct is measured by a mercury manometer. For a given mercury-level difference
between the two columns, the absolute pressure in the duct is to be determined.
Properties
The density of mercury is given to be ρ = 13,600 kg/m3.
Analysis
lower level.
(a) The pressure in the duct is above atmospheric pressure since the fluid column on the duct side is at a
(b) The absolute pressure in the duct is determined from
P = Patm + ρ gh
⎛ 1 N
⎞ ⎛ 1 kPa ⎞
= (100 kPa) + (13,600 kg/m3 )(9.81 m/s 2 )(0.030 m) ⎜
2 ⎟⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠ ⎝ 1000 N/m ⎠
= 104.00 kPa ≅ 104 kPa
Discussion
The final result is given to three significant digits.
3-14
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-31
Solution
The systolic and diastolic pressures of a healthy person are given in mm of Hg. These pressures are to be
expressed in kPa, psi, and meters of water column.
Assumptions
Both mercury and water are incompressible substances.
Properties
We take the densities of water and mercury to be 1000 kg/m3 and 13,600 kg/m3, respectively.
Analysis
Using the relation P = ρgh for gage pressure, the high and low pressures are expressed as
⎛
1N
Phigh = ρghhigh = (13,600 kg/m 3 )(9.81 m/s 2 )(0.12 m)⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞⎛ 1 kPa
⎟⎜
⎟⎜ 1 000 N/m 2
⎠⎝
⎞
⎟ = 16.0 kPa
⎟
⎠
⎛ 1N
⎞⎛ 1 kPa ⎞
⎟⎜
⎟ = 10.7 kPa
Plow = ρghlow = (13,600 kg/m 3 )(9.81 m/s 2 )(0.08 m)⎜
⎜ 1 kg ⋅ m/s 2 ⎟⎜ 1000 N/m 2 ⎟
⎝
⎠⎝
⎠
Noting that 1 psi = 6.895 kPa,
⎛ 1 psi ⎞
⎛ 1 psi ⎞
⎟⎟ = 2.32 psi and
⎟⎟ = 1.55 psi
Phigh = (16.0 kPa)⎜⎜
Plow = (10.7 k Pa)⎜⎜
⎝ 6.895 kPa ⎠
⎝ 6.895 kPa ⎠
For a given pressure, the relation P = ρgh is expressed for mercury and water as P = ρ water gh water and
P = ρ mercury ghmercury . Setting these two relations equal to each other and solving for water height gives
P = ρ water ghwater = ρ mercury ghmercury
Therefore,
hwater, high =
hwater, low =
ρ mercury
ρ water
ρ mercury
ρ water
hmercury, high =
hmercury, low =
→
hwater =
13,600 kg/m 3
1000 kg/m 3
13,600 kg/m 3
1000 kg/m 3
ρ mercury
ρ water
hmercury
h
(0.12 m) = 1.63 m
(0.08 m) = 1.09 m
Discussion
Note that measuring blood pressure with a water monometer would involve water column heights higher
than the person’s height, and thus it is impractical. This problem shows why mercury is a suitable fluid for blood pressure
measurement devices.
3-32
Solution
A vertical tube open to the atmosphere is connected to the vein in the arm of a person. The height that the
blood rises in the tube is to be determined.
Assumptions
1 The density of blood is constant. 2 The gage pressure of blood is 120 mmHg.
Properties
The density of blood is given to be ρ = 1050 kg/m3.
Analysis
For a given gage pressure, the relation P = ρgh can be expressed for
mercury and blood as P = ρ blood ghblood and P = ρ mercury ghmercury . Setting these two
Blood
h
relations equal to each other we get
P = ρ blood ghblood = ρ mercury ghmercury
Solving for blood height and substituting gives
ρ mercury
13,600 kg/m 3
hblood =
hmercury =
(0.12 m) = 1.55 m
ρ blood
1050 kg/m 3
Discussion
Note that the blood can rise about one and a half meters in a tube connected to the vein. This explains why
IV tubes must be placed high to force a fluid into the vein of a patient.
3-15
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-33
Solution
A man is standing in water vertically while being completely submerged. The difference between the
pressure acting on his head and the pressure acting on his toes is to be determined.
Assumptions
Water is an incompressible substance, and thus the density does not change with depth.
Properties
We take the density of water to be ρ =1000 kg/m3.
Analysis
The pressures at the head and toes of the person can be expressed as
Phead = Patm + ρghhead
and
hhead
Ptoe = Patm + ρgh toe
where h is the vertical distance of the location in water from the free surface. The pressure
difference between the toes and the head is determined by subtracting the first relation
above from the second,
htoe
Ptoe − Phead = ρgh toe − ρghhead = ρg (h toe − hhead )
Substituting,
⎛
⎞⎛ 1kPa ⎞
1N
⎟⎜
⎟ = 17.7 kPa
Ptoe − Phead = (1000 kg/m 3 )(9.81 m/s 2 )(1.80 m - 0)⎜
⎜ 1kg ⋅ m/s 2 ⎟⎜ 1000 N/m 2 ⎟
⎝
⎠⎝
⎠
Discussion
This problem can also be solved by noting that the atmospheric pressure (1 atm = 101.325 kPa) is
equivalent to 10.3-m of water height, and finding the pressure that corresponds to a water height of 1.8 m.
3-34
Solution
Water is poured into the U-tube from one arm and oil from the other arm. The water column height in one
arm and the ratio of the heights of the two fluids in the other arm are given. The height of each fluid in that arm is to be
determined.
Assumptions
Both water and oil are incompressible substances.
Properties
The density of oil is given to be ρoil = 790 kg/m3. We take the density of water to be ρw =1000 kg/m3.
Analysis
The height of water column in the left arm of the manometer is given to be hw1 = 0.70 m. We let the height
of water and oil in the right arm to be hw2 and ha, respectively. Then, ha = 6hw2. Noting that both arms are open to the
atmosphere, the pressure at the bottom of the U-tube can be expressed as
Pbottom = Patm + ρ w gh w1
and
Pbottom = Patm + ρ w gh w2 + ρ a gha
Setting them equal to each other and simplifying,
ρ w gh w1 = ρ w gh w2 + ρ a gha
→
ρ w h w1 = ρ w h w2 + ρ a ha
→
Noting that ha = 6hw2 and we take ρa =ρoil, the water and oil column heights in the
second arm are determined to be
0.7 m = h w2 + (790/1000)6h w2 →
0.7 m = 0.122 m + (790/1000)ha →
h w1 = h w2 + ( ρ a / ρ w )ha
Water
h w2 = 0.122 m
ha = 0.732 m
oil
ha
hw1
hw2
Discussion
Note that the fluid height in the arm that contains oil is higher. This is
expected since oil is lighter than water.
3-16
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-35
Solution
The hydraulic lift in a car repair shop is to lift cars. The fluid gage pressure that must be maintained in the
reservoir is to be determined.
W = mg
Assumptions The weight of the piston of the lift is negligible.
Analysis
Pressure is force per unit area, and thus the gage pressure required is simply the
ratio of the weight of the car to the area of the lift,
Pgage =
(2000 kg)(9.81 m/s 2 ) ⎛⎜
mg
1 kN
W
=
=
2
2
⎜
A πD / 4
π (0.30 m) / 4 ⎝ 1000 kg ⋅ m/s 2
Patm
⎞
⎟ = 278 kN/m 2 = 278 kPa
⎟
⎠
P
Note that the pressure level in the reservoir can be reduced by using a piston with a larger area.
Discussion
3-36
Solution
Fresh and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube
manometer. The pressure difference between the two pipelines is to be determined.
Assumptions 1 All the liquids are incompressible. 2 The effect
of air column on pressure is negligible.
Properties
The densities of seawater and mercury are given to
be ρsea = 1035 kg/m3 and ρHg = 13,600 kg/m3. We take the density
of water to be ρw =1000 kg/m3.
Air
hsea
hair
Analysis
Starting with the pressure in the fresh water pipe
(point 1) and moving along the tube by adding (as we go down) or
subtracting (as we go up) the ρgh terms until we reach the sea
water pipe (point 2), and setting the result equal to P2 gives
Sea
water
Fresh
water
hw
P1 + ρ w gh w − ρ Hg ghHg − ρ air ghair + ρ sea ghsea = P2
hHg
Mercury
Rearranging and neglecting the effect of air column on pressure,
P1 − P2 = − ρ w gh w + ρ Hg ghHg − ρ sea ghsea = g ( ρ Hg hHg − ρ w hw − ρ sea hsea )
Substituting,
P1 − P2 = (9.81 m/s 2 )[(13600 kg/m 3 )(0.1 m)
⎛
1 kN
− (1000 kg/m 3 )(0.6 m) − (1035 kg/m 3 )(0.4 m)]⎜
⎜ 1000 kg ⋅ m/s 2
⎝
⎞
⎟
⎟
⎠
= 3.39 kN/m 2 = 3.39 kPa
Therefore, the pressure in the fresh water pipe is 3.39 kPa higher than the pressure in the sea water pipe.
Discussion
A 0.70-m high air column with a density of 1.2 kg/m3 corresponds to a pressure difference of 0.008 kPa.
Therefore, its effect on the pressure difference between the two pipes is negligible.
3-17
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-37
Solution
Fresh and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube
manometer. The pressure difference between the two pipelines is to be determined.
Assumptions
All the liquids are incompressible.
Properties
The densities of seawater and mercury are given to be ρsea = 1035 kg/m3 and ρHg = 13,600 kg/m3. We take
the density of water to be ρw =1000 kg/m3. The specific gravity of oil is given to be 0.72, and thus its density is 720 kg/m3.
Analysis
Starting with the pressure in the fresh water pipe (point 1) and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms until we reach the sea water pipe (point 2), and setting the result equal
to P2 gives
P1 + ρ w gh w − ρ Hg ghHg − ρ oil ghoil + ρ sea ghsea = P2
Rearranging,
P1 − P2 = − ρ w gh w + ρ Hg ghHg + ρ oil ghoil − ρ sea ghsea
= g ( ρ Hg hHg + ρ oil hoil − ρ w hw − ρ sea hsea )
Substituting,
P1 − P2 = (9.81 m/s 2 )[(13600 kg/m 3 )(0.1 m) + (720 kg/m 3 )(0.7 m) − (1000 kg/m 3 )(0.6 m)
⎛
1 kN
− (1035 kg/m 3 )(0.4 m)]⎜
⎜ 1000 kg ⋅ m/s 2
⎝
⎞
⎟
⎟
⎠
= 8.34 kN/m 2 = 8.34 kPa
Therefore, the pressure in the fresh water pipe is 8.34 kPa higher than the pressure in the sea water pipe.
Oil
hsea
Fresh
water
hoil
Sea
water
hw
hHg
Mercury
Discussion
The result is greater than that of the previous problem since the oil is heavier than the air.
3-18
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-38E
Solution
The pressure in a natural gas pipeline is measured by a double U-tube manometer with one of the arms
open to the atmosphere. The absolute pressure in the pipeline is to be determined.
Assumptions 1 All the liquids are incompressible. 2 The effect of air column on pressure is negligible. 3 The pressure
throughout the natural gas (including the tube) is uniform since its density is low.
Properties
We take the density of water to be ρw = 62.4 lbm/ft3. The specific gravity of mercury is given to be 13.6,
and thus its density is ρHg = 13.6×62.4 = 848.6 lbm/ft3.
Analysis
Starting with the pressure at point 1 in the natural gas pipeline, and moving along the tube by adding (as we
go down) or subtracting (as we go up) the ρgh terms until we reach the free surface of oil where the oil tube is exposed to
the atmosphere, and setting the result equal to Patm gives
P1 − ρ Hg ghHg − ρ water ghwater = Patm
Solving for P1,
P1 = Patm + ρ Hg ghHg + ρ water gh1
Substituting,
⎛
1 lbf
P = 14.2 psia + (32.2 ft/s 2 )[(848.6 lbm/ft 3 )(6/12 ft) + (62.4 lbm/ft 3 )(27/12 ft)]⎜
⎜ 32.2 lbm ⋅ ft/s 2
⎝
= 18.1 psia
⎞⎛ 1 ft 2
⎟⎜
⎟⎜ 144 in 2
⎠⎝
⎞
⎟
⎟
⎠
Air
10in
Water
hw
hHg
Natural
gas
Mercury
Discussion
Note that jumping horizontally from one tube to the next and realizing that pressure remains the same in the
same fluid simplifies the analysis greatly. Also, it can be shown that the 15-in high air column with a density of 0.075
lbm/ft3 corresponds to a pressure difference of 0.00065 psi. Therefore, its effect on the pressure difference between the two
pipes is negligible.
3-19
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-39E
Solution
The pressure in a natural gas pipeline is measured by a double U-tube manometer with one of the arms
open to the atmosphere. The absolute pressure in the pipeline is to be determined.
Assumptions 1 All the liquids are incompressible. 2 The pressure throughout the natural gas (including the tube) is
uniform since its density is low.
Properties
We take the density of water to be ρw = 62.4 lbm/ft3. The specific gravity of mercury is given to be 13.6,
and thus its density is ρHg = 13.6×62.4 = 848.6 lbm/ft3. The specific gravity of oil is given to be 0.69, and thus its density is
ρoil = 0.69×62.4 = 43.1 lbm/ft3.
Analysis
Starting with the pressure at point 1 in the natural gas pipeline, and moving along the tube by adding (as we
go down) or subtracting (as we go up) the ρgh terms until we reach the free surface of oil where the oil tube is exposed to
the atmosphere, and setting the result equal to Patm gives
P1 − ρ Hg ghHg + ρ oil ghoil − ρ water gh water = Patm
Solving for P1,
P1 = Patm + ρ Hg gh Hg + ρ water gh1 − ρ oil ghoil
Substituting,
P1 = 14.2 psia + (32.2 ft/s 2 )[(848.6 lbm/ft 3 )(6/12 ft) + (62.4 lbm/ft 3 )(27/12 ft)
= 17.7 psia
⎛
1lbf
− (43.1lbm/ft 3 )(15/12 ft)]⎜
⎜ 32.2 lbm ⋅ ft/s 2
⎝
⎞⎛ 1ft 2
⎟⎜
⎟⎜ 144 in 2
⎠⎝
⎞
⎟
⎟
⎠
Oil
Water
hw
hHg
Natural
gas
hoil
Mercury
Discussion
Note that jumping horizontally from one tube to the next and realizing that pressure remains the same in the
same fluid simplifies the analysis greatly.
3-20
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-40
Solution
The gage pressure of air in a pressurized water tank is measured simultaneously by both a pressure gage
and a manometer. The differential height h of the mercury column is to be determined.
Assumptions The air pressure in the tank is uniform (i.e., its variation with elevation is negligible due to its low density),
and thus the pressure at the air-water interface is the same as the indicated gage pressure.
Properties
We take the density of water to be ρw =1000 kg/m3. The specific gravities of oil and mercury are given to
be 0.72 and 13.6, respectively.
Analysis
Starting with the pressure of air in the tank (point 1), and moving along the tube by adding (as we go down)
or subtracting (as we go up) the ρgh terms until we reach the free surface of oil where the oil tube is exposed to the
atmosphere, and setting the result equal to Patm gives
P1 + ρ w gh w − ρ Hg ghHg − ρ oil ghoil = Patm
65 kPa
Rearranging,
Air
P1 − Patm = ρ oil ghoil + ρ Hg ghHg − ρ w gh w
hoil
or,
P1,gage
ρw g
Water
= ρ s,oil hoil + ρ s, Hg hHg − h w
hw
Substituting,
⎛
⎞⎛ 1000 kg ⋅ m/s 2
65 kPa
⎜
⎟⎜
⎜ (1000 kg/m 3 )(9.81 m/s 2 ) ⎟⎜ 1 kPa. ⋅ m 2
⎝
⎠⎝
hHg
⎞
⎟ = 0.72 × (0.75 m) + 13.6 × hHg − 0.3 m
⎟
⎠
Solving for hHg gives hHg = 0.47 m. Therefore, the differential height of the mercury column must be 47 cm.
Discussion
Double instrumentation like this allows one to verify the measurement of one of the instruments by the
measurement of another instrument.
3-21
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-41
Solution
The gage pressure of air in a pressurized water tank is measured simultaneously by both a pressure gage
and a manometer. The differential height h of the mercury column is to be determined.
Assumptions The air pressure in the tank is uniform (i.e., its variation with elevation is negligible due to its low density),
and thus the pressure at the air-water interface is the same as the indicated gage pressure.
Properties
We take the density of water to be ρw =1000 kg/m3. The specific gravities of oil and mercury are given to
be 0.72 and 13.6, respectively.
Analysis
Starting with the pressure of air in the tank (point 1), and moving along the tube by adding (as we go down)
or subtracting (as we go up) the ρgh terms until we reach the free surface of oil where the oil tube is exposed to the
atmosphere, and setting the result equal to Patm gives
P1 + ρ w gh w − ρ Hg ghHg − ρ oil ghoil = Patm
45 kPa
Rearranging,
P1 − Patm = ρ oil ghoil + ρ Hg ghHg − ρ w gh w
Air
hoil
or,
P1,gage
ρw g
Water
= SG oil hoil + SG Hg hHg − h w
hw
Substituting,
⎛ 1000 kg ⋅ m/s 2
⎜
]
(1000 kg/m 3 )(9.81 m/s 2 ) ⎜⎝ 1 kPa. ⋅ m 2
45 kPa
hHg
⎞
⎟ = 0.72 × (0.75 m) + 13.6 × hHg − 0.3 m
⎟
⎠
Solving for hHg gives hHg = 0.32 m. Therefore, the differential height of the mercury column must be 32 cm.
Discussion
Double instrumentation like this allows one to verify the measurement of one of the instruments by the
measurement of another instrument.
3-42
Solution
The top part of a water tank is divided into two compartments, and a fluid with an unknown density is
poured into one side. The levels of the water and the liquid are measured. The density of the fluid is to be determined.
Assumptions
water.
1 Both water and the added liquid are incompressible substances. 2 The added liquid does not mix with
Properties
We take the density of water to be ρ =1000 kg/m3.
Analysis
Both fluids are open to the atmosphere. Noting that the pressure
of both water and the added fluid is the same at the contact surface, the pressure
at this surface can be expressed as
Pcontact = Patm + ρ f ghf = Patm + ρ w gh w
Fluid
Water
hf
hw
Simplifying, we have ρf ghf = ρ w ghw . Solving for ρf gives
ρf =
hw
45 cm
ρw =
(1000 kg/m3 ) = 562.5 kg/m3 ≅ 563 kg/m3
80 cm
hf
Discussion
Note that the added fluid is lighter than water as expected (a heavier fluid would sink in water).
3-22
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-43
Solution
A load on a hydraulic lift is to be raised by pouring oil from a thin tube. The height of oil in the tube
required in order to raise that weight is to be determined.
Assumptions 1 The cylinders of the lift are vertical. 2 There are no leaks. 3 Atmospheric pressure act on both sides, and
thus it can be disregarded.
Properties
The density of oil is given to be ρ =780 kg/m3.
Analysis
Noting that pressure is force per unit area, the gage pressure in the fluid under the load is simply the ratio of
the weight to the area of the lift,
Pgage =
mg
(500 kg)(9.81 m/s 2 ) ⎛⎜
W
1 kN
=
=
A πD 2 / 4
π (1.20 m) 2 / 4 ⎜⎝ 1000 kg ⋅ m/s 2
⎞
⎟ = 4.34 kN/m 2 = 4.34 kPa
⎟
⎠
The required oil height that will cause 4.34 kPa of pressure rise is
Pgage = ρgh →
h=
Pgage
ρg
=
⎛ 1000 kg ⋅ m/s 2
⎜
(780 kg/m 3 )(9.81 m/s 2 ) ⎜⎝ 1kN/m 2
4.34 kN/m 2
⎞
⎟ = 0.567 m
⎟
⎠
Therefore, a 500 kg load can be raised by this hydraulic lift by simply raising the oil level in the tube by 56.7 cm.
LOAD
500 kg
h
1.2 m
Discussion
1 cm
Note that large weights can be raised by little effort in hydraulic lift by making use of Pascal’s principle.
3-23
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-44E
Solution
Two oil tanks are connected to each other through a mercury manometer. For a given differential height,
the pressure difference between the two tanks is to be determined.
Assumptions 1 Both the oil and mercury are incompressible fluids. 2
The oils in both tanks have the same density.
Properties
The densities of oil and mercury are given to be ρoil =
45 lbm/ft3 and ρHg = 848 lbm/ft3.
Analysis
Starting with the pressure at the bottom of tank 1
(where pressure is P1) and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms until we reach the
bottom of tank 2 (where pressure is P2) gives
10 in
32 in
P1 + ρ oil g (h1 + h2 ) − ρ Hg gh2 − ρ oil gh1 = P2
where h1 = 10 in and h2 = 32 in. Rearranging and simplifying,
Mercury
P1 − P2 = ρ Hg gh2 − ρ oil gh 2 = ( ρ Hg − ρ oil ) gh2
Substituting,
⎛
1lbf
ΔP = P1 − P2 = (848 - 45 lbm/ft 3 )(32.2 ft/s 2 )(32/12 ft)⎜⎜
2
⎝ 32.2 lbm ⋅ ft/s
⎞⎛ 1ft 2
⎟⎜
⎟⎜ 144 in 2
⎠⎝
⎞
⎟ = 14.9 psia
⎟
⎠
Therefore, the pressure in the left oil tank is 14.9 psia higher than the pressure in the right oil tank.
Discussion
Note that large pressure differences can be measured conveniently by mercury manometers. If a water
manometer were used in this case, the differential height would be over 30 ft.
3-45
Solution
The standard atmospheric pressure is expressed in terms of mercury, water, and glycerin columns.
Assumptions The densities of fluids are constant.
Properties
The specific gravities are given to be SG = 13.6 for mercury, SG = 1.0 for water, and SG = 1.26 for
glycerin. The standard density of water is 1000 kg/m3, and the standard atmospheric pressure is 101,325 Pa.
Analysis
The atmospheric pressure is expressed in terms of a fluid column height as
Patm
→ h=
Patm = ρgh = SGρ w gh
SGρ w g
Substituting,
(a) Mercury:
h=
⎛ 1 kg ⋅ m/s 2
Patm
101,325 N/m 2
=
3
2 ⎜
SGρ w g 13.6(1000 kg/m )(9.81 m/s ) ⎝ 1 N/m 2
(b) Water:
h=
⎛ 1 kg ⋅ m/s 2
Patm
101,325 N/m 2
=
3
2 ⎜
SGρ w g 1(1000 kg/m )(9.81 m/s ) ⎝ 1 N/m 2
(c) Glycerin:
h=
⎛ 1 kg ⋅ m/s 2
Patm
101,325 N/m 2
=
3
2 ⎜
SGρ w g 1.26(1000 kg/m )(9.81 m/s ) ⎝ 1 N/m 2
⎞
⎟ = 0.759 m
⎠
⎞
⎟ = 10.3 m
⎠
⎞
⎟ = 8.20 m
⎠
Discussion
Using water or glycerin to measure atmospheric pressure requires very long vertical tubes (over 10 m for
water), which is not practical. This explains why mercury is used instead of water or a light fluid.
3-24
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-46
Solution
A glass filled with water and covered with a thin paper is inverted. The pressure at the bottom of the glass
is to be determined.
Assumptions 1 Water is an incompressible substance. 2 The weight of the paper is negligible. 3 The atmospheric
pressure is 100 kPa.
Pbottom
Properties
We take the density of water to be ρ =1000 kg/m3.
Analysis
The paper is in equilibrium, and thus the net force acting on the
paper must be zero. A vertical force balance on the paper involves the pressure
forces on both sides, and yields
P1 Aglass = Patm Aglass
→
P1 = Patm
That is, the pressures on both sides of the paper must be the same.
The pressure at the bottom of the glass is determined from the hydrostatic
pressure relation to be
Patm = Pbottom + ρghglass
→
P1
Pbottom = Patm − ρghglass
Substituting,
⎞⎛ 1kPa ⎞
⎛
1N
Patm
⎟ = 99.0 kPa
⎟⎜
Pbottom = (100 kPa) − (1000 kg/m 3 )(9.81 m/s 2 )(0.1 m)⎜
2
⎜ 1kg ⋅ m/s ⎟⎜ 1000 N/m 2 ⎟
⎠
⎠⎝
⎝
Discussion
Note that there is a vacuum of 1 kPa at the bottom of the glass, and thus there is an upward pressure force
acting on the water body, which balanced by the weight of water. As a result, the net downward force on water is zero, and
thus water does not flow down.
3-25
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-47
Solution
Two chambers with the same fluid at their base are separated by a piston. The gage pressure in each air
chamber is to be determined.
Piston
Assumptions 1 Water is an incompressible substance. 2 The
variation of pressure with elevation in each air chamber is
A
air B
negligible because of the low density of air.
air
Properties
We take the density of water to be ρ =1000
D
kg/m3.
50 cm
The piston is in equilibrium, and thus the net
Analysis
force acting on the piston must be zero. A vertical force
balance on the piston involves the pressure force exerted by
water on the piston face, the atmospheric pressure force, and
the piston weight, and yields
PC Apiston = Patm Apiston + W piston
→
PC = Patm +
C
30 cm
30 cm
25 cm
E
W piston
water
Apiston
90 cm
The pressure at the bottom of each air chamber is determined
from the hydrostatic pressure relation to be
Pair A = PE = PC + ρg CE = Patm +
W piston
Pair B = PD = PC − ρg CD = Patm +
W piston
Apiston
Apiston
+ ρg CE
→
Pair
− ρg CD
→
Pair B, gage =
A, gage
=
W piston
Apiston
W piston
Apiston
+ ρg CE
− ρg CD
Substituting,
⎛ 1N
25 N
+ (1000 kg/m3 )(9.81 m/s 2 )(0.25 m) ⎜
2
2
π ( 0.3 m) / 4
⎝ 1 kg ⋅ m/s
Pair A, gage =
Pair B, gage =
25 N
π ( 0.3 m) 2 / 4
Discussion
⎛ 1N
− (1000 kg/m3 )(9.81 m/s 2 )(0.25 m) ⎜
2
⎝ 1 kg ⋅ m/s
⎞
2
⎟ = 2806 N/m = 2.81 kPa
⎠
⎞
2
⎟ = −2099 N/m = −2.10 kPa
⎠
Note that there is a vacuum of about 2 kPa in tank B which pulls the water up.
3-26
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-48
Solution
A double-fluid manometer attached to an air pipe is considered. The specific gravity of one fluid is known,
and the specific gravity of the other fluid is to be determined.
Assumptions 1 Densities of liquids are constant. 2 The air pressure in the tank is uniform (i.e., its variation with elevation
is negligible due to its low density), and thus the pressure at the air-water interface is the same as the indicated gage
pressure.
Properties
kg/m3.
The specific gravity of one fluid is given to be 13.55. We take the standard density of water to be 1000
Analysis
Starting with the pressure of air in the tank, and moving along the tube by adding (as we go down) or
subtracting (as we go up) the ρgh terms until we reach the free surface where the oil tube is exposed to the atmosphere,
and setting the result equal to Patm give
Pair + ρ 1 gh1 − ρ 2 gh2 = Patm
→
Pair − Patm = SG 2 ρ w gh2 − SG1 ρ w gh1
Rearranging and solving for SG2,
SG 2 = SG1
⎞ ⎛ 1000 kg ⋅ m/s 2 ⎞
( 76 − 100 ) kPa
h1 Pair − Patm
0.22 m ⎛
+
= 13.55
+⎜
⎟⎜
⎟ = 1.34
3
2
0.40 m ⎝ (1000 kg/m )(9.81 m/s )(0.40 m) ⎠ ⎝ 1 kPa ⋅ m 2 ⎠
ρ w gh2
h2
Air
P = 76 kPa
40 cm
22 cm
Fluid 2
SG2
Fluid 1
SG1
Discussion
Note that the right fluid column is higher than the left, and this would imply above atmospheric pressure in
the pipe for a single-fluid manometer.
3-27
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-49
Solution
The pressure difference between two pipes is measured by a double-fluid manometer. For given fluid
heights and specific gravities, the pressure difference between the pipes is to be calculated.
Assumptions
All the liquids are incompressible.
Properties
The specific gravities are given to be 13.5 for mercury, 1.26 for glycerin, and 0.88 for oil. We take the
standard density of water to be ρw =1000 kg/m3.
Analysis
Starting with the pressure in the water pipe (point A) and moving along the tube by adding (as we go down)
or subtracting (as we go up) the ρgh terms until we reach the oil pipe (point B), and setting the result equal to PB give
PA + ρ w gh w + ρ Hg gh Hg − ρ gly ghgly + ρ pil ghoil = PB
Rearranging and using the definition of specific gravity,
PB − PA = SG w ρ w ghw + SG Hg ρ w ghHg − SG gly ρ w ghgly + SG oil ρ w ghoil
= g ρ w ( SG w hw + SG Hg hHg − SG gly hgly + SG oil hoil )
Substituting,
⎛
1 kN
PB − PA = (9.81 m/s 2 )(1000 kg/m 3 )[1(0.6 m) + 13.5(0.2 m) − 1.26(0.45 m) + 0.88(0.1 m)]⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟
⎟
⎠
= 27.7 kN/m 2 = 27.7 kPa
Therefore, the pressure in the oil pipe is 27.7 kPa higher than the pressure in the water pipe.
A
Water,
SG=1.0
Glycerin,
SG=1.26
Oil
SG=0.88
60 cm
10 cm
B
15 cm
20 cm
Mercury,
SG=13.56
Discussion
Using a manometer between two pipes is not recommended unless the pressures in the two pipes are
relatively constant. Otherwise, an over-rise of pressure in one pipe can push the manometer fluid into the other pipe,
creating a short circuit.
3-28
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-50
Solution
The fluid levels in a multi-fluid U-tube manometer change as a result of a pressure drop in the trapped air
space. For a given pressure drop and brine level change, the area ratio is to be determined.
Assumptions 1 All the liquids are incompressible. 2 Pressure in the brine pipe remains constant. 3 The variation of
pressure in the trapped air space is negligible.
Properties
The specific gravities are given to be 13.56 for mercury and 1.1 for brine. We take the standard density of
water to be ρw =1000 kg/m3.
Analysis
It is clear from the problem statement and the figure that the brine pressure is much higher than the air
pressure, and when the air pressure drops by 0.7 kPa, the pressure difference between the brine and the air space also
increases by the same amount. Starting with the air pressure (point A) and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms until we reach the brine pipe (point B), and setting the result equal to PB
before and after the pressure change of air give
Before:
PA1 + ρ w gh w + ρ Hg ghHg, 1 − ρ br ghbr,1 = PB
After:
PA2 + ρ w gh w + ρ Hg ghHg, 2 − ρ br gh br,2 = PB
Subtracting,
PA2 − PA1 + ρ Hg gΔhHg − ρ br gΔh br = 0 →
PA1 − PA 2
= SG Hg ΔhHg − SG br Δhbr = 0
ρw g
(1)
where ΔhHg and Δh br are the changes in the differential mercury and brine column heights, respectively, due to the drop
in air pressure. Both of these are positive quantities since as the mercury-brine interface drops, the differential fluid heights
for both mercury and brine increase. Noting also that the volume of mercury is constant, we have A1 ΔhHg,left = A2 ΔhHg, right
and
PA2 − PA1 = −0.7 kPa = −700 N/m 2 = −700 kg/m ⋅ s 2
Δh br = 0.005 m
ΔhHg = ΔhHg,right + ΔhHg,left = Δhbr + Δhbr A2 /A 1 = Δhbr (1 + A2 /A 1 )
Substituting,
700 kg/m ⋅ s 2
(1000 kg/m 3 )(9.81 m/s 2 )
= [13.56 × 0.005(1 + A2 /A1 ) - .1.1× 0.005] m
It gives
A2/A1 = 0.134
A
Air
B
Brine
pipe
Water
Area, A1
SG=1.1
Mercury
SG=13.56
Δhb = 5 mm
Area, A2
Discussion
In addition to the equations of hydrostatics, we also utilize conservation of mass in this problem.
3-29
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-51
Solution
Two water tanks are connected to each other through a mercury manometer with inclined tubes. For a given
pressure difference between the two tanks, the parameters a and θ are to be determined.
Assumptions
Both water and mercury are incompressible liquids.
Properties
kg/m3.
The specific gravity of mercury is given to be 13.6. We take the standard density of water to be ρw =1000
Analysis
Starting with the pressure in the tank A and moving along the tube by adding (as we go down) or
subtracting (as we go up) the ρgh terms until we reach tank B, and setting the result equal to PB give
PA + ρ w ga + ρ Hg g 2a − ρ w ga = PB
→
2 ρ Hg ga = PB − PA
Rearranging and substituting the known values,
a=
⎛ 1000 kg ⋅ m/s 2
PB − PA
20 kN/m 2
⎜
=
2 ρ Hg g
1 kN
2(13.6)(1000 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
⎞
⎟ = 0.0750 m = 7.50 cm
⎟
⎠
From geometric considerations,
26.8 sin θ = 2a
(cm)
Therefore,
sin θ =
Water
A
2a
2 × 7.50
=
= 0.560
26.8
26.8
θ = 34.0°
→
a
26.8 cm
2a
a
θ
Discussion
Water
B
Mercury
Note that vertical distances are used in manometer analysis. Horizontal distances are of no consequence.
3-30
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-52
Solution
A multi-fluid container is connected to a U-tube. For the given specific gravities and fluid column heights,
the gage pressure at A and the height of a mercury column that would create the same pressure at A are to be determined.
1 All the liquids are incompressible. 2 The multi-fluid container is open to the atmosphere.
Assumptions
Properties
The specific gravities are given to be 1.26 for glycerin and 0.90 for oil. We take the standard density of
water to be ρw =1000 kg/m3, and the specific gravity of mercury to be 13.6.
Analysis
Starting with the atmospheric pressure on the top surface
of the container and moving along the tube by adding (as we go down) or
subtracting (as we go up) the ρgh terms until we reach point A, and
setting the result equal to PA give
70 cm
Oil
SG=0.90
30 cm
Water
20 cm
Glycerin
SG=1.26
A
Patm + ρ oil ghoil + ρ w gh w − ρ gly ghgly = PA
Rearranging and using the definition of specific gravity,
PA − Patm = SG oil ρ w ghoil + SG w ρ w ghw − SG gly ρ w ghgly
or
PA,gage = g ρ w ( SG oil hoil + SG w hw − SG gly hgly )
90 cm
15 cm
Substituting,
⎛
1 kN
PA, gage = (9.81 m/s 2 )(1000 kg/m 3 )[0.90(0.70 m) + 1(0.3 m) − 1.26(0.70 m)]⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟
⎟
⎠
= 0.471 kN/m 2 = 0.471 kPa
The equivalent mercury column height is
h Hg =
Discussion
manometers.
PA, gage
ρ Hg g
=
⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
(13.6)(1000 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
0.471 kN/m 2
⎞
⎟ = 0.00353 m = 0.353 cm
⎟
⎠
Note that the high density of mercury makes it a very suitable fluid for measuring high pressures in
3-31
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
Fluid Statics: Hydrostatic Forces on Plane and Curved Surfaces
3-53C
Solution
We are to define resultant force and center of pressure.
Analysis
The resultant hydrostatic force acting on a submerged surface is the resultant of the pressure forces
acting on the surface. The point of application of this resultant force is called the center of pressure.
Discussion
The center of pressure is generally not at the center of the body, due to hydrostatic pressure variation.
3-54C
Solution
We are to examine a claim about hydrostatic force.
Analysis
Yes, because the magnitude of the resultant force acting on a plane surface of a completely submerged
body in a homogeneous fluid is equal to the product of the pressure PC at the centroid of the surface and the area A of the
surface. The pressure at the centroid of the surface is PC = P0 + ρghC where hC is the vertical distance of the centroid
from the free surface of the liquid.
Discussion
We have assumed that we also know the pressure at the liquid surface.
3-55C
Solution
We are to consider the effect of plate rotation on the hydrostatic force on the plate surface.
Analysis
There will be no change on the hydrostatic force acting on the top surface of this submerged horizontal flat
plate as a result of this rotation since the magnitude of the resultant force acting on a plane surface of a completely
submerged body in a homogeneous fluid is equal to the product of the pressure PC at the centroid of the surface and the
area A of the surface.
Discussion
If the rotation were not around the centroid, there would be a change in the force.
3-56C
Solution
We are to explain why dams are bigger at the bottom than at the top.
Analysis
Dams are built much thicker at the bottom because the pressure force increases with depth, and the
bottom part of dams are subjected to largest forces.
Discussion
Dam construction requires an enormous amount of concrete, so tapering the dam in this way saves a lot of
concrete, and therefore a lot of money.
3-57C
Solution
We are to explain how to determine the horizontal component of hydrostatic force on a curved surface.
Analysis
The horizontal component of the hydrostatic force acting on a curved surface is equal (in both magnitude
and the line of action) to the hydrostatic force acting on the vertical projection of the curved surface.
Discussion
We could also integrate pressure along the surface, but the method discussed here is much simpler and
yields the same answer.
3-32
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-58C
Solution
We are to explain how to determine the vertical component of hydrostatic force on a curved surface.
Analysis
The vertical component of the hydrostatic force acting on a curved surface is equal to the hydrostatic
force acting on the horizontal projection of the curved surface, plus (minus, if acting in the opposite direction) the
weight of the fluid block.
Discussion
We could also integrate pressure along the surface, but the method discussed here is much simpler and
yields the same answer.
3-59C
Solution
We are to explain how to determine the line of action on a circular surface.
Analysis
The resultant hydrostatic force acting on a circular surface always passes through the center of the circle
since the pressure forces are normal to the surface, and all lines normal to the surface of a circle pass through the center of
the circle. Thus the pressure forces form a concurrent force system at the center, which can be reduced to a single
equivalent force at that point. If the magnitudes of the horizontal and vertical components of the resultant hydrostatic force
are known, the tangent of the angle the resultant hydrostatic force makes with the horizontal is tan α = FV / FH .
Discussion
This fact makes analysis of circular-shaped surfaces simple. There is no corresponding simplification for
shapes other than circular, unfortunately.
3-60
Solution
A car is submerged in water. The hydrostatic force on the door and its line of action are to be determined
for the cases of the car containing atmospheric air and the car is filled with water.
Assumptions 1 The bottom surface of the lake is horizontal. 2 The door can be approximated as a vertical rectangular
plate. 3 The pressure in the car remains at atmospheric value since there is no water leaking in, and thus no compression of
the air inside. Therefore, we can ignore the atmospheric pressure in calculations since it acts on both sides of the door.
Properties
We take the density of lake water to be 1000 kg/m3 throughout.
Analysis
(a) When the car is well-sealed and thus the pressure inside the car is the atmospheric pressure, the average
pressure on the outer surface of the door is the pressure at the centroid (midpoint) of the surface, and is determined to be
Pavg = PC = ρ ghC = ρ g ( s + b / 2 )
⎛
1 kN
= (1000 kg/m3 )( 9.81 m/s 2 ) ( 8 + 1.1 / 2 m ) ⎜
2
⎝ 1000 kg ⋅ m/s
⎞
2
⎟ = 83.88 kN/m
⎠
Then the resultant hydrostatic force on the door becomes
s=8m
FR = Pave A = (83.88 kN/m 2 )(0.9 m × 1.1 m) = 83.0 kN
The pressure center is directly under the midpoint of the plate, and its distance
from the surface of the lake is determined to be
yP = s +
b
b2
1.1
1.12
+
= 8+
+
= 8.56 m
2 12(8 + 1.1 / 2)
2 12( s + b / 2)
Door, 1.1 m × 0.9 m
(b) When the car is filled with water, the net force normal to the surface of the door is zero since the pressure on both sides
of the door will be the same.
Discussion
Note that it is impossible for a person to open the door of the car when it is filled with atmospheric air. But
it takes little effort to open the door when car is filled with water, because then the pressure on each side of the door is the
same.
3-33
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-61E
Solution
The height of a water reservoir is controlled by a cylindrical gate hinged to the reservoir. The hydrostatic
force on the cylinder and the weight of the cylinder per ft length are to be determined.
Assumptions 1 The hinge is frictionless. 2 Atmospheric pressure acts on both sides of the gate, and thus it can be ignored
in calculations for convenience.
Properties
We take the density of water to be 62.4 lbm/ft3 throughout.
Analysis
(a) We consider the free body diagram of the liquid block enclosed by the circular surface of the cylinder
and its vertical and horizontal projections. The hydrostatic forces acting on the vertical and horizontal plane surfaces as
well as the weight of the liquid block per ft length of the cylinder are:
Horizontal force on vertical surface:
FH = Fx = Pave A = ρghC A = ρg ( s + R / 2) A
1 lbf
⎛
⎞
= (62.4 lbm/ft 3 )(32.2 ft/s 2 )(13 + 2 / 2 ft)(2 ft × 1 ft)⎜
⎟
2
⎝ 32.2 lbm ⋅ ft/s ⎠
= 1747 lbf
Vertical force on horizontal surface (upward):
s = 13 ft
R=2 ft
Fy = Pavg A = ρ ghC A = ρ ghbottom A
1 lbf
⎛
⎞
= ( 62.4 lbm/ft 3 )( 32.2 ft/s 2 ) (15 ft )( 2 ft × 1 ft ) ⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
= 1872 lbf
b=R
=2 ft
FH
Weight of fluid block per ft length (downward):
W = mg = ρgV = ρg ( R 2 − πR 2 / 4 )(1 ft) = ρgR 2 (1 − π / 4 )(1 ft)
W
FV
1 lbf
⎞
⎛
= (62.4 lbm/ft 3 )(32.2 ft/s 2 )(2 ft) 2 (1 - π/4)(1 ft)⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
= 54 lbf
Therefore, the net upward vertical force is
FV = F y − W = 1872 − 54 = 1818 lbf
Then the magnitude and direction of the hydrostatic force acting on the cylindrical surface become
FR = FH2 + FV2 = 1747 2 + 18182 = 2521 lbf ≅ 2520 lbf
tan θ =
FV 1818 lbf
=
= 1.041 → θ = 46.1°
FH 1747 lbf
Therefore, the magnitude of the hydrostatic force acting on the cylinder is 2521 lbf per ft length of the cylinder, and its line
of action passes through the center of the cylinder making an angle 46.1° upwards from the horizontal.
(b) When the water level is 15-ft high, the gate opens and the reaction force at the bottom of the cylinder becomes zero.
Then the forces other than those at the hinge acting on the cylinder are its weight, acting through the center, and the
hydrostatic force exerted by water. Taking a moment about the point A where the hinge is and equating it to zero gives
FR Rsinθ − Wcyl R = 0
→
Wcyl = FR sinθ = (2521 lbf)sin46.1° = 1817 lbf ≅ 1820 lbf (per ft)
Discussion
The weight of the cylinder per ft length is determined to be 1820 lbf, which corresponds to a mass of 1820
lbm, and to a density of 145 lbm/ft3 for the material of the cylinder.
3-34
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-62
Solution
An above the ground swimming pool is filled with water. The hydrostatic force on each wall and the
distance of the line of action from the ground are to be determined, and the effect of doubling the wall height on the
hydrostatic force is to be assessed.
Assumptions Atmospheric pressure acts on both sides of the wall of the pool, and thus it can be ignored in calculations
for convenience.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and is determined to be
Pavg = PC = ρ ghC = ρ g( h / 2 )
⎛ 1N
⎞
= (1000 kg/m3 )( 9.81 m/s 2 ) (1.5 / 2 m ) ⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
2
= 7357.5 N/m
2h/3
FR
h = 1.5 m
h/3
Then the resultant hydrostatic force on each wall becomes
FR = Pavg A = ( 7357.5 N/m 2 ) ( 4 m × 1.5 m ) = 44,145 N ≅ 44.1 kN
The line of action of the force passes through the pressure center, which is 2h/3 from the free surface and h/3 from the
bottom of the pool. Therefore, the distance of the line of action from the ground is
yP =
h 1.5
=
= 0.50 m (from the bottom)
3
3
If the height of the walls of the pool is doubled, the hydrostatic force quadruples since
FR = ρghC A = ρg (h / 2)(h × w) = ρgwh 2 / 2
and thus the hydrostatic force is proportional to the square of the wall height, h2.
Discussion
This is one reason why above-ground swimming pools are not very deep, whereas in-ground swimming
pools can be quite deep.
3-35
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-63E
Solution
A dam is filled to capacity. The total hydrostatic force on the dam, and the pressures at the top and the
bottom are to be determined.
Assumptions
convenience.
Atmospheric pressure acts on both sides of the dam, and thus it can be ignored in calculations for
Properties
We take the density of water to be 62.4 lbm/ft3 throughout.
Analysis
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and is determined to be
Pavg = ρ ghC = ρ g ( h / 2 )
1 lbf
⎛
⎞
= ( 62.4 lbm/ft 3 )( 32.2 ft/s 2 ) ( 200 / 2 ft ) ⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
2
= 6240 lbf/ft
2h/3
FR
h=200 ft
h/3
Then the resultant hydrostatic force acting on the dam becomes
FR = Pave A = ( 6240 lbf/ft 2 ) ( 200 ft × 1200 ft ) = 1.50 × 109 lbf
Resultant force per unit area is pressure, and its value at the top and the bottom of the dam becomes
Ptop = ρgh top = 0 lbf/ft 2
1 lbf
⎛
⎞
= 12 , 480 lbf/ft 2 ≅ 12,500 lbf/ft 2
Pbottom = ρ ghbottom = ( 62.4 lbm/ft 3 )( 32.2 ft/s 2 ) ( 200 ft ) ⎜
2 ⎟
32.2
lbm
ft/s
⋅
⎝
⎠
Discussion
The values above are gave pressures, of course. The gage pressure at the bottom of the dam is about 86.6
psig, or 101.4 psia, which is almost seven times greater than standard atmospheric pressure.
3-64
Solution
A room in the lower level of a cruise ship is considered. The hydrostatic force acting on the window and
the pressure center are to be determined.
Assumptions
convenience.
Atmospheric pressure acts on both sides of the window, and thus it can be ignored in calculations for
Properties
The specific gravity of sea water is given to be 1.025, and thus its density is 1025 kg/m3.
Analysis
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and is determined to be
⎛ 1N
⎞
Pavg = PC = ρ ghC = (1025 kg/m3 )( 9.81 m/s 2 ) ( 5 m ) ⎜
= 50 , 276 N/m 2
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
5m
Then the resultant hydrostatic force on each wall becomes
FR = Pavg A = Pavg [π D 2 / 4] = (50 , 276 N/m 2 )[π ( 0.3 m) 2 / 4] = 3554 N ≅ 3550 N
The line of action of the force passes through the pressure center, whose vertical
distance from the free surface is determined from
yP = yC +
I xx ,C
yC A
= yC +
FR
D=0.3 m
π R4 / 4
R2
( 0.15 m )2
= yC +
= 5+
= 5.0011 m ≅ 5.00 m
2
4 yC
4( 5 m )
yC π R
Discussion
For small surfaces deep in a liquid, the pressure center nearly coincides with the centroid of the surface.
Here, in fact, to three significant digits in the final answer, the center of pressure and centroid are coincident.
3-36
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-65
Solution
The cross-section of a dam is a quarter-circle. The hydrostatic force on the dam and its line of action are to
be determined.
Assumptions
convenience.
Atmospheric pressure acts on both sides of the dam, and thus it can be ignored in calculations for
Properties
We take the density of water to be 1000 kg/m3 throughout.
Analysis
We consider the free body diagram of the liquid block enclosed by the circular surface of the dam and its
vertical and horizontal projections. The hydrostatic forces acting on the vertical and horizontal plane surfaces as well as the
weight of the liquid block are:
Horizontal force on vertical surface:
FH = Fx = Pavg A = ρ ghC A = ρ g( R / 2 )A
Fy = 0
⎛ 1N
⎞
= (1000 kg/m3 )( 9.81 m/s 2 ) (10 / 2 m )(10 m × 100 m ) ⎜
2 ⎟
⋅
1
kg
m/s
⎝
⎠
7
= 4.905 × 10 N
R = 10 m
FH
Vertical force on horizontal surface is zero since it coincides with the free
surface of water. The weight of fluid block per m length is
FV = W = ρgV = ρg[ w × πR 2 / 4]
W
⎛
1N
= (1000 kg/m 3 )(9.81 m/s 2 )[(100 m)π (10 m) 2 /4]⎜⎜
1
kg
⋅ m/s 2
⎝
⎞
⎟
⎟
⎠
= 7.705 × 10 7 N
Then the magnitude and direction of the hydrostatic force acting on the surface of the dam become
FR = FH2 + FV2 =
tanθ =
( 4.905 ×10 N ) + ( 7.705 ×10 N )
7
FV 7.705 × 107 N
=
= 1.571
FH 4.905 × 107 N
2
7
→
2
= 9.134 × 107 N ≅ 9.13 × 107 N
θ = 57.5°
Therefore, the line of action of the hydrostatic force passes through the center of the curvature of the dam, making 57.5°
downwards from the horizontal.
Discussion
If the shape were not circular, it would be more difficult to determine the line of action.
3-37
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-66
Solution
A rectangular plate hinged about a horizontal axis along its upper edge blocks a fresh water channel. The
plate is restrained from opening by a fixed ridge at a point B. The force exerted to the plate by the ridge is to be determined.
Assumptions
convenience.
Atmospheric pressure acts on both sides of the plate, and thus it can be ignored in calculations for
Properties
We take the density of water to be 1000 kg/m3 throughout.
A
Analysis
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and is determined to be
Pavg = PC = ρ ghC = ρ g( h / 2 )
s=1m
⎛
⎞
1 kN
= (1000 kg/m3 )( 9.81 m/s 2 ) ( 4 / 2 m ) ⎜
= 19.62 kN/m 2
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠
Then the resultant hydrostatic force on each wall becomes
FR = Pavg A = (19.62 kN/m 2 ) ( 4 m × 5 m ) = 392 kN
The line of action of the force passes through the pressure center, which is 2h/3
from the free surface,
yP =
FR
h=4m
Fridge
B
2h 2 × (4 m)
=
= 2.667 m
3
3
Taking the moment about point A and setting it equal to zero gives
∑M
A
=0
→
FR ( s + y P ) = Fridge AB
Solving for Fridge and substituting, the reaction force is determined to be
s + yP
(1 + 2.667) m
FR =
(392 kN) = 288 kN
Fridge =
5m
AB
Discussion
The difference between FR and Fridge is the force acting on the hinge at point A.
3-38
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-67
Solution
The previous problem is reconsidered. The effect of water depth on the force exerted on the plate by the
ridge as the water depth varies from 0 to 5 m in increments of 0.5 m is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
g=9.81 "m/s2"
rho=1000 "kg/m3"
s=1"m"
w=5 "m"
A=w*h
P_ave=rho*g*h/2000 "kPa"
F_R=P_ave*A "kN"
y_p=2*h/3
F_ridge=(s+y_p)*F_R/(s+h)
Dept
h, m
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Pave,
kPa
0
2.453
4.905
7.358
9.81
12.26
14.72
17.17
19.62
22.07
24.53
FR
kN
0.0
6.1
24.5
55.2
98.1
153.3
220.7
300.4
392.4
496.6
613.1
yp
m
0.00
0.33
0.67
1.00
1.33
1.67
2.00
2.33
2.67
3.00
3.33
Fridge
kN
0
5
20
44
76
117
166
223
288
361
443
450
400
350
300
Fridge, kN
250
200
150
100
50
0
0
1
2
3
4
5
h, m
Discussion
The force on the ridge does not increase linearly, as we may have suspected.
3-39
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-68E
Solution
The flow of water from a reservoir is controlled by an L-shaped gate hinged at a point A. The required
weight W for the gate to open at a specified water height is to be determined.
Assumptions 1 Atmospheric pressure acts on both sides of the gate, and thus it can be ignored in calculations for
convenience. 2 The weight of the gate is negligible.
We take the density of water to be 62.4 lbm/ft3 throughout.
Properties
8 ft
Analysis
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and is determined to be
W
Pavg = ρ ghC = ρ g ( h / 2 )
A
1 lbf
⎛
⎞
= ( 62.4 lbm/ft )( 32.2 ft/s ) (12 / 2 ft ) ⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
2
= 374.4 lbf/ft
3
2
Then the resultant hydrostatic force acting on the dam becomes
FR
s = 3 ft
B
h=12 ft
FR = Pavg A = ( 374.4 lbf/ft 2 ) (12 ft × 5 ft ) = 22,464 lbf
The line of action of the force passes through the pressure center, which is 2h/3
from the free surface,
yP =
2h 2 × (12 ft)
=
= 8 ft
3
3
Taking the moment about point A and setting it equal to zero gives
∑M
A
=0
→
FR ( s + y P ) = W AB
Solving for W and substituting, the required weight is determined to be
s + yP
(3 + 8) ft
FR =
(22,464 lbf) = 30,900 lbf
W=
8 ft
AB
Discussion
Note that the required weight is inversely proportional to the distance of the weight from the hinge.
3-40
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-69E
Solution
The flow of water from a reservoir is controlled by an L-shaped gate hinged at a point A. The required
weight W for the gate to open at a specified water height is to be determined.
Assumptions 1 Atmospheric pressure acts on both sides of the gate, and thus it can be ignored in calculations for
convenience. 2 The weight of the gate is negligible.
We take the density of water to be 62.4 lbm/ft3 throughout.
Properties
8 ft
Analysis
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and is determined to be
W
Pavg = ρ ghC = ρ g ( h / 2 )
B
A
s = 7 ft
1 lbf
⎛
⎞
= ( 62.4 lbm/ft 3 )( 32.2 ft/s 2 ) ( 8 / 2 ft ) ⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
2
= 249.6 lbf/ft
Then the resultant hydrostatic force acting on the dam becomes
FR
h=8 ft
FR = Pavg A = ( 249.6 lbf/ft 2 ) ( 8 ft × 5 ft ) = 9984 lbf
The line of action of the force passes through the pressure center, which is 2h/3
from the free surface,
2h 2 × (8 ft)
=
= 5.333 ft
3
3
yP =
Taking the moment about point A and setting it equal to zero gives
∑M
A
=0
→
FR ( s + y P ) = W AB
Solving for W and substituting, the required weight is determined to be
W=
Discussion
( 7 + 5.333) ft
s + yP
FR =
( 9984 lbf ) = 15,390 lbf ≅ 15,400 lbf
8 ft
AB
Note that the required weight is inversely proportional to the distance of the weight from the hinge.
3-41
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-70
Solution
Two parts of a water trough of semi-circular cross-section are held together by cables placed along the
length of the trough. The tension T in each cable when the trough is full is to be determined.
Assumptions 1 Atmospheric pressure acts on both sides of the trough wall, and thus it can be ignored in calculations for
convenience. 2 The weight of the trough is negligible.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
To expose the cable tension, we consider half of the trough whose cross-section is quarter-circle. The
hydrostatic forces acting on the vertical and horizontal plane surfaces as well as the weight of the liquid block are:
Horizontal force on vertical surface:
FH = Fx = Pavg A = ρ ghC A = ρ g( R / 2 )A
⎛ 1N
⎞
= (1000 kg/m3 )( 9.81 m/s 2 ) ( 0.5 / 2 m ) (0.5 m × 3 m) ⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
= 3679 N
T
θ
R = 0.5 m
The vertical force on the horizontal surface is zero, since it coincides with the
free surface of water. The weight of fluid block per 3-m length is
FV = W = ρgV = ρg[ w × πR 2 / 4]
⎛
1N
= (1000 kg/m )(9.81 m/s )[(3 m)π (0.5 m) /4]⎜⎜
1
kg
⋅ m/s 2
⎝
= 5779 N
3
2
2
⎞
⎟
⎟
⎠
FH
FR
A
W
Then the magnitude and direction of the hydrostatic force acting on the surface of the 3-m long section of the trough
become
FR = FH2 + FV2 = (3679 N) 2 + (5779 N) 2 = 6851 N
tan θ =
FV
5779 N
=
= 1.571
FH 3679 N
→ θ = 57.5°
Therefore, the line of action passes through the center of the curvature of the trough, making 57.5° downwards from the
horizontal. Taking the moment about point A where the two parts are hinged and setting it equal to zero gives
∑M
A
=0
→
FR Rsin( 90 − 57.5 )° = TR
Solving for T and substituting, the tension in the cable is determined to be
T = FR sin ( 90 − 57.5 ) ° = ( 6851 N ) sin ( 90 − 57.5 ) ° = 3681 N ≅ 3680 N
Discussion
This problem can also be solved without finding FR by finding the lines of action of the horizontal
hydrostatic force and the weight.
3-42
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-71
Solution
Two parts of a water trough of triangular cross-section are held together by cables placed along the length
of the trough. The tension T in each cable when the trough is filled to the rim is to be determined.
Assumptions 1 Atmospheric pressure acts on both sides of the trough wall, and thus it can be ignored in calculations for
convenience. 2 The weight of the trough is negligible.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
To expose the cable tension, we consider half of the trough whose cross-section is triangular. The water
height h at the midsection of the trough and width of the free surface are
T
b
h = L sin θ = (0.75 m)sin45° = 0.530 m
b = L cos θ = (0.75 m)cos45° = 0.530 m
The hydrostatic forces acting on the vertical and horizontal plane surfaces as
well as the weight of the liquid block are determined as follows:
0.75 m
FH
W
Horizontal force on vertical surface:
FH = Fx = Pavg A = ρ ghC A = ρ g ( h / 2 ) A
45°
A
⎛ 1N
⎞
= (1000 kg/m3 )( 9.81 m/s 2 ) ( 0.530 / 2 m ) (0.530 m × 6 m) ⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
= 8267 N
The vertical force on the horizontal surface is zero since it coincides with the free surface
of water. The weight of fluid block per 6-m length is
FV = W = ρgV = ρg[ w × bh / 2]
⎛
1N
= (1000 kg/m 3 )(9.81 m/s 2 )[(6 m)(0.530 m)(0.530 m)/2]⎜
⎜ 1 kg ⋅ m/s 2
⎝
= 8267 N
⎞
⎟
⎟
⎠
The distance of the centroid of a triangle from a side is 1/3 of the height of the triangle for that side. Taking the moment
about point A where the two parts are hinged and setting it equal to zero gives
∑M
A
=0
→
W
b
h
+ FH = Th
3
3
Solving for T and substituting, and noting that h = b, the tension in the cable is determined to be
T=
Discussion
FH + W ( 8267 + 8267 ) N
=
= 5511 N ≅ 5510 N
3
3
The analysis is simplified because of the symmetry of the trough.
3-43
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-72
Solution
Two parts of a water trough of triangular cross-section are held together by cables placed along the length
of the trough. The tension T in each cable when the trough is filled to the rim is to be determined.
Assumptions 1 Atmospheric pressure acts on both sides of the trough wall, and thus it can be ignored in calculations for
convenience. 2 The weight of the trough is negligible.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
To expose the cable tension, we consider half of the trough whose cross-section is triangular. The water
height is given to be h = 0.4 m at the midsection of the trough, which is equivalent to the width of the free surface b since
tan 45° = b/h = 1. The hydrostatic forces acting on the vertical and horizontal plane surfaces as well as the weight of the
liquid block are determined as follows:
b
T
Horizontal force on vertical surface:
FH = Fx = Pavg A = ρ ghC A = ρ g ( h / 2 ) A
⎛ 1N
⎞
= (1000 kg/m3 )( 9.81 m/s 2 ) ( 0.4 / 2 m ) (0.4 m × 3 m) ⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
= 2354 N
0.4 m
FH
W
45°
A
The vertical force on the horizontal surface is zero since it coincides with the free surface
of water. The weight of fluid block per 3-m length is
FV = W = ρgV = ρg[ w × bh / 2]
⎛
1N
= (1000 kg/m 3 )(9.81 m/s 2 )[(3 m)(0.4 m)(0.4 m)/2]⎜⎜
2
⎝ 1 kg ⋅ m/s
= 2354 N
⎞
⎟
⎟
⎠
The distance of the centroid of a triangle from a side is 1/3 of the height of the triangle for that side. Taking the moment
about point A where the two parts are hinged and setting it equal to zero gives
∑M
A
=0
→
W
b
h
+ FH = Th
3
3
Solving for T and substituting, and noting that h = b, the tension in the cable is determined to be
T=
FH + W ( 2354 + 2354 ) N
=
= 1569 N ≅ 1570 N
3
3
Discussion
The tension force here is a factor of about 3.5 smaller than that of the previous problem, even though the
trough is more than half full.
3-44
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-73
Solution
A retaining wall against mud slide is to be constructed by rectangular concrete blocks. The mud height at
which the blocks will start sliding, and the blocks will tip over are to be determined.
Assumptions
convenience.
Atmospheric pressure acts on both sides of the wall, and thus it can be ignored in calculations for
Properties
The density is given to be 1800 kg/m3 for the mud, and 2700 kg/m3 for concrete blocks.
Analysis
ground are
(a) The weight of the concrete wall per unit length (L = 1 m) and the friction force between the wall and the
⎛
1N
W block = ρgV = (2700 kg/m 3 )(9.81 m/s 2 )[0.2 × 0.8 × 1 m 3 )⎜⎜
2
⎝ 1 kg ⋅ m/s
Ffriction = μW block = 0.3(4238 N ) = 1271 N
⎞
⎟ = 4238 N
⎟
⎠
t =0.2 m
The hydrostatic force exerted by the mud to the wall is
FH = Fx = Pavg A = ρ ghC A = ρ g ( h / 2 ) A
⎛ 1N
⎞
= (1800 kg/m )( 9.81 m/s ) ( h / 2 ) (1× h ) ⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
2
= 8829h N
3
0.8 m
h
2
Setting the hydrostatic and friction forces equal to each other gives
FH
W
Ffriction
A
FH = Ffriction
→ 8829 h 2 = 1271
→
h = 0.38 m
(b) The line of action of the hydrostatic force passes through the pressure center, which is 2h/3 from the free surface. The
line of action of the weight of the wall passes through the midplane of the wall. Taking the moment about point A and
setting it equal to zero gives
∑M
A
=0
→
W block (t / 2) = FH (h / 3) →
W block (t / 2) = 8829h 3 / 3
Solving for h and substituting, the mud height for tip over is determined to be
t⎞
⎛ 3W
h = ⎜ block ⎟
⎝ 2 × 8829 ⎠
Discussion
1/ 3
⎛ 3 × 4238 × 0.2 ⎞
=⎜
⎟
⎝ 2 × 8829 ⎠
1/ 3
= 0.52 m
The concrete wall will slide before tipping. Therefore, sliding is more critical than tipping in this case.
3-45
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-74
Solution
A retaining wall against mud slide is to be constructed by rectangular concrete blocks. The mud height at
which the blocks will start sliding, and the blocks will tip over are to be determined.
Assumptions
convenience.
Atmospheric pressure acts on both sides of the wall, and thus it can be ignored in calculations for
Properties
The density is given to be 1800 kg/m3 for the mud, and 2700 kg/m3 for concrete blocks.
Analysis
ground are
(a) The weight of the concrete wall per unit length (L = 1 m) and the friction force between the wall and the
⎛
1N
W block = ρgV = (2700 kg/m 3 )(9.81 m/s 2 )[0.4 × 0.8 × 1 m 3 )⎜⎜
2
⎝ 1 kg ⋅ m/s
Ffriction = μW block = 0.3(8476 N ) = 2543 N
⎞
⎟ = 8476 N
⎟
⎠
t =0.4 m
The hydrostatic force exerted by the mud to the wall is
FH = Fx = Pavg A = ρ ghC A = ρ g ( h / 2 ) A
0.8 m
⎛ 1N
⎞
= (1800 kg/m3 )( 9.81 m/s 2 ) ( h / 2 ) (1× h ) ⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
2
= 8829h N
Setting the hydrostatic and friction forces equal to each other gives
FH = Ffriction
→ 8829 h 2 = 2543
→
h
FH
W
Ffriction
A
h = 0.54 m
(b) The line of action of the hydrostatic force passes through the pressure center, which is 2h/3 from the free surface. The
line of action of the weight of the wall passes through the midplane of the wall. Taking the moment about point A and
setting it equal to zero gives
∑M
A
=0
→
W block (t / 2) = FH (h / 3) →
W block (t / 2) = 8829h 3 / 3
Solving for h and substituting, the mud height for tip over is determined to be
t⎞
⎛ 3W
h = ⎜ block ⎟
⎝ 2 × 8829 ⎠
Discussion
case.
1/ 3
⎛ 3 × 8476 × 0.3 ⎞
=⎜
⎟
⎝ 2 × 8829 ⎠
1/ 3
= 0.76 m
Note that the concrete wall will slide before tipping. Therefore, sliding is more critical than tipping in this
3-46
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-75 [Also solved using EES on enclosed DVD]
Solution
A quarter-circular gate hinged about its upper edge controls the flow of water over the ledge at B where the
gate is pressed by a spring. The minimum spring force required to keep the gate closed when the water level rises to A at
the upper edge of the gate is to be determined.
Assumptions 1 The hinge is frictionless. 2 Atmospheric pressure acts on both sides of the gate, and thus it can be ignored
in calculations for convenience. 3 The weight of the gate is negligible.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
We consider the free body diagram of the liquid block enclosed by the circular surface of the gate and its
vertical and horizontal projections. The hydrostatic forces acting on the vertical and horizontal plane surfaces as well as the
weight of the liquid block are determined as follows:
A
Horizontal force on vertical surface:
FH = Fx = Pave A = ρghC A = ρg ( R / 2) A
W
⎛
1 kN
= (1000 kg/m 3 )(9.81 m/s 2 )(3 / 2 m)(4 m × 3 m)⎜
⎜ 1000 kg ⋅ m/s 2
⎝
= 176.6 kN
Vertical force on horizontal surface (upward):
⎞
⎟
⎟
⎠
Fx
R=3m
Fs
B
Fy
Fy = Pavg A = ρ ghC A = ρ ghbottom A
⎛
1 kN
= (1000 kg/m3 )( 9.81 m/s 2 ) ( 3 m ) (4 m × 3 m) ⎜
1000
kg ⋅ m/s 2
⎝
⎞
⎟ = 353.2 kN
⎠
The weight of fluid block per 4-m length (downwards):
W = ρ gV = ρ g ⎡⎣ w × π R 2 / 4 ⎤⎦
⎛
1 kN
= (1000 kg/m3 )( 9.81 m/s 2 ) ⎡⎣( 4 m ) π (3 m) 2 /4 ⎤⎦ ⎜
2
⎝ 1000 kg ⋅ m/s
Therefore, the net upward vertical force is
⎞
⎟ = 277.4 kN
⎠
FV = F y − W = 353.2 − 277.4 = 75.8 kN
Then the magnitude and direction of the hydrostatic force acting on the surface of the 4-m long quarter-circular section of
the gate become
FR = FH2 + FV2 = (176.6 kN) 2 + (75.8 kN) 2 = 192.2 kN
tan θ =
FV
75.8 kN
=
= 0.429
FH 176.6 kN
→ θ = 23.2°
Therefore, the magnitude of the hydrostatic force acting on the gate is 192.2 kN, and its line of action passes through the
center of the quarter-circular gate making an angle 23.2° upwards from the horizontal.
The minimum spring force needed is determined by taking a moment about the point A where the hinge is, and
setting it equal to zero,
∑M
A
=0
→ FR R sin(90 − θ ) − Fspring R = 0
Solving for Fspring and substituting, the spring force is determined to be
Fspring = FR sin(90 - θ ) = (192.2 kN) sin(90° − 23.2°) = 177 kN
Discussion
Several variations of this design are possible. Can you think of some of them?
3-47
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-76
Solution
A quarter-circular gate hinged about its upper edge controls the flow of water over the ledge at B where the
gate is pressed by a spring. The minimum spring force required to keep the gate closed when the water level rises to A at
the upper edge of the gate is to be determined.
Assumptions 1 The hinge is frictionless. 2 Atmospheric pressure acts on both sides of the gate, and thus it can be ignored
in calculations for convenience. 3 The weight of the gate is negligible.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
We consider the free body diagram of the liquid block enclosed by the circular surface of the gate and its
vertical and horizontal projections. The hydrostatic forces acting on the vertical and horizontal plane surfaces as well as the
weight of the liquid block are determined as follows:
Horizontal force on vertical surface:
FH = Fx = Pave A = ρghC A = ρg ( R / 2) A
A
⎛
1 kN
= (1000 kg/m 3 )(9.81 m/s 2 )(4 / 2 m)(4 m × 4 m)⎜
⎜ 1000 kg ⋅ m/s 2
⎝
= 313.9 kN
Vertical force on horizontal surface (upward):
⎞
⎟
⎟
⎠
W
Fx
R=4m
Fs
F y = Pave A = ρghC A = ρghbottom A
B
⎛
1 kN
= (1000 kg/m 3 )(9.81 m/s 2 )(4 m)(4 m × 4 m)⎜
⎜ 1000 kg ⋅ m/s 2
⎝
= 627.8 kN
⎞
⎟
⎟
⎠
Fy
The weight of fluid block per 4-m length (downwards):
W = ρgV = ρg [ w × πR 2 / 4]
⎛
1 kN
= (1000 kg/m 3 )(9.81 m/s 2 )[(4 m)π (4 m) 2 /4]⎜⎜
2
⎝ 1000 kg ⋅ m/s
= 493.1 kN
Therefore, the net upward vertical force is
FV = F y − W = 627.8 − 493.1 = 134.7 kN
⎞
⎟
⎟
⎠
Then the magnitude and direction of the hydrostatic force acting on the surface of the 4-m long quarter-circular section of
the gate become
FR = FH2 + FV2 = (313.9 kN) 2 + (134.7 kN) 2 = 341.6 kN
FV
134.7kN
=
= 0.429 → θ = 23.2°
FH 313.9 kN
Therefore, the magnitude of the hydrostatic force acting on the gate is 341.6 kN, and its line of action passes through the
center of the quarter-circular gate making an angle 23.2° upwards from the horizontal.
tan θ =
The minimum spring force needed is determined by taking a moment about the point A where the hinge is, and
setting it equal to zero,
∑M
A
=0
→ FR R sin(90 − θ ) − Fspring R = 0
Solving for Fspring and substituting, the spring force is determined to be
Fspring = FR sin ( 90 - θ ) = (341.6 kN)sin ( 90° − 23.2° ) = 314 kN
Discussion
If the previous problem is solved using a program like EES, it is simple to repeat with different values.
3-48
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
Buoyancy
3-77C
Solution
We are to define and discuss the buoyant force.
Analysis
The upward force a fluid exerts on an immersed body is called the buoyant force. The buoyant force is
caused by the increase of pressure in a fluid with depth. The magnitude of the buoyant force acting on a submerged
body whose volume is V is expressed as FB = ρ f gV . The direction of the buoyant force is upwards, and its line of
action passes through the centroid of the displaced volume.
Discussion
If the buoyant force is greater than the body’s weight, it floats.
3-78C
Solution
We are to compare the buoyant force on two spheres.
Analysis
The magnitude of the buoyant force acting on a submerged body whose volume is V is expressed as
FB = ρ f gV , which is independent of depth. Therefore, the buoyant forces acting on two identical spherical balls
submerged in water at different depths is the same.
Discussion
Buoyant force depends only on the volume of the object, not its density.
3-79C
Solution
We are to compare the buoyant force on two spheres.
Analysis
The magnitude of the buoyant force acting on a submerged body whose volume is V is expressed as
FB = ρ f gV , which is independent of the density of the body ( ρ f is the fluid density). Therefore, the buoyant forces
acting on the 5-cm diameter aluminum and iron balls submerged in water is the same.
Discussion
Buoyant force depends only on the volume of the object, not its density.
3-80C
Solution
We are to compare the buoyant forces on a cube and a sphere.
Analysis
The magnitude of the buoyant force acting on a submerged body whose volume is V is expressed as
FB = ρ f gV , which is independent of the shape of the body. Therefore, the buoyant forces acting on the cube and
sphere made of copper submerged in water are the same since they have the same volume.
Discussion
The two objects have the same volume because they have the same mass and density.
3-49
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-81C
Solution
We are to discuss the stability of a submerged and a floating body.
Analysis
A submerged body whose center of gravity G is above the center of buoyancy B, which is the centroid
of the displaced volume, is unstable. But a floating body may still be stable when G is above B since the centroid of
the displaced volume shifts to the side to a point B’ during a rotational disturbance while the center of gravity G of
the body remains unchanged. If the point B’ is sufficiently far, these two forces create a restoring moment, and return the
body to the original position.
Stability analysis like this is critical in the design of ship hulls, so that they are least likely to capsize.
Discussion
3-82
Solution
The density of a liquid is to be determined by a hydrometer by establishing division marks in water and in
the liquid, and measuring the distance between these marks.
We take the density of pure water to be 1000 kg/m3.
Properties
Analysis
A hydrometer floating in water is in static equilibrium, and the buoyant force FB exerted by the liquid must
always be equal to the weight W of the hydrometer, FB = W.
FB = ρgV sub = ρghAc
mark for water
where h is the height of the submerged portion of the hydrometer and Ac is the
cross-sectional area which is constant.
In pure water:
W = ρ w ghw Ac
In the liquid:
W = ρ liquid ghliquid Ac
0.5 cm
10 cm
W
Liquid
Setting the relations above equal to each other (since both equal the weight of
the hydrometer) gives
ρ w ghw Ac = ρ liquid ghliquid Ac
FB
Solving for the liquid density and substituting,
ρliquid =
hwater
10 cm
(1000 kg/m 3 ) = 1053 kg/m3 ≅ 1050 kg/m3
ρ water =
hliquid
(10 − 0.5 ) cm
Discussion
Note that for a given cylindrical hydrometer, the product of the fluid density and the height of the
submerged portion of the hydrometer is constant in any fluid.
3-50
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-83E
Solution
A concrete block is lowered into the sea. The tension in the rope is to be determined before and after the
block is immersed in water.
Assumptions
1 The buoyancy force in air is negligible. 2 The weight of the rope is negligible.
Properties
The density of steel block is given to be 494 lbm/ft3.
Analysis
(a) The forces acting on the concrete block in air are its downward weight and the upward pull action
(tension) by the rope. These two forces must balance each other, and thus the tension in the rope must be equal to the
weight of the block:
V = 4π R 3 / 3 = 4π (1.5 ft ) /3 = 14.137 ft 3
3
FT
FT = W = ρconcrete gV
1 lbf
⎛
⎞
= ( 494 lbm/ft 3 )( 32.2 ft/s 2 )(14.137 ft 3 ) ⎜
= 6984 lbf ≅ 6980 lbf
2 ⎟
⋅
32.2
lbm
ft/s
⎝
⎠
(b) When the block is immersed in water, there is the additional force of buoyancy
acting upwards. The force balance in this case gives
1 lbf
⎛
⎞
= 882 lbf
FB = ρ f gV = ( 62.4 lbm/ft 3 )( 32.2 ft/s 2 )(14.137 ft 3 ) ⎜
2 ⎟
32.2
lbm
ft/s
⋅
⎝
⎠
FT,water = W − FB = 6984 − 882 = 6102 lbf ≅ 6100 lbf
W
FB
Discussion
Note that the weight of the concrete block and thus the tension of the rope
decreases by (6984 – 6102)/6984 = 12.6% in water.
3-84
Solution
An irregularly shaped body is weighed in air and then in water with a spring scale. The volume and the
average density of the body are to be determined.
Properties
We take the density of water to be 1000 kg/m3.
Assumptions
1 The buoyancy force in air is negligible. 2 The body is completely submerged in water.
Analysis
The mass of the body is
m=
Wair
7200 N
=
g
9.81 m/s 2
⎛ 1 kg ⋅ m/s 2
⎜
⎜
1N
⎝
⎞
⎟ = 733.9 kg
⎟
⎠
Water
FB
Mass,
m V
The difference between the weights in air and in water is due to the buoyancy
force in water,
FB = Wair − W water = 7200 − 4790 = 2410 N
Noting that FB = ρ water gV , the volume of the body is determined to be
V=
FB
ρ water g
=
2410 N
(1000 kg/m3 )( 9.81 m/s2 )
Air
Wwater = 4790 N
Wwir=6800 N
= 0.2457 m3 ≅ 0.246 m3
Then the density of the body becomes
ρ=
m
733.9 kg
=
= 2987 kg/m3 ≅ 2990 kg/m3
V 0.2457 m3
Discussion
The volume of the body can also be measured by observing the change in the volume of the container when
the body is dropped in it (assuming the body is not porous).
3-51
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-85
Solution
The height of the portion of a cubic ice block that extends above the water surface is measured. The height
of the ice block below the surface is to be determined.
Assumptions
sea.
1 The buoyancy force in air is negligible. 2 The top surface of the ice block is parallel to the surface of the
Properties
The specific gravities of ice and seawater are given to be 0.92 and 1.025, respectively, and thus the
corresponding densities are 920 kg/m3 and 1025 kg/m3.
Analysis
The weight of a body floating in a fluid is equal to the buoyant force acting on it (a consequence of vertical
force balance from static equilibrium). Therefore, in this case the average density of the body must be equal to the density
of the fluid since
W = FB → ρ body gV total = ρ fluid gV submerged
Vsubmerged
V total
=
ρ body
Ice block
Sea
ρ fluid
W
The cross-sectional of a cube is constant, and thus the “volume ratio” can be
replaced by “height ratio”. Then,
hsubmerged
htotal
=
ρ body
ρ fluid
→
ρ
h
= ice
h + 0.10 ρ water
10 cm
→
h
h
0.92
=
h + 0.10 1.025
FB
where h is the height of the ice block below the surface. Solving for h gives
h = 0.876 m = 87.6 cm
Discussion
Note that the 0.92/1.025 = 90% of the volume of an ice block remains under water. For symmetrical ice
blocks this also represents the fraction of height that remains under water.
3-86
Solution
A man dives into a lake and tries to lift a large rock. The force that the man needs to apply to lift it from the
bottom of the lake is to be determined.
Assumptions
1 The rock is c completely submerged in water. 2 The buoyancy force in air is negligible.
Properties
The density of granite rock is given to be 2700 kg/m3. We take the density of water to be 1000 kg/m3.
The weight and volume of the rock are
⎛
⎞
1N
⎟ = 1668 N
W = mg = (170 kg)(9.81 m/s 2 )⎜⎜
2 ⎟
⋅
1
kg
m/s
⎝
⎠
170 kg
m
3
= 0.06296 m
V = =
ρ 2700 kg/m 3
The buoyancy force acting on the rock is
Analysis
⎛ 1N
⎞
= 618 N
FB = ρ water gV = (1000 kg/m3 )( 9.81 m/s 2 )( 0.06296 m3 ) ⎜
2 ⎟
⋅
1
kg
m/s
⎝
⎠
The weight of a body submerged in water is equal to the weigh of the body in air
minus the buoyancy force,
Win water = Win air − FB = 1668 − 618 = 1050 N
Discussion
This force corresponds to a mass of m =
Water
W
FB
Fnet =W - FB
⎞
Win water
1050 N ⎛ 1 N
=
= 107 kg . Therefore, a
2 ⎜
2 ⎟
g
9.81 m/s ⎝ 1 kg ⋅ m/s ⎠
person who can lift 107 kg on earth can lift this rock in water.
3-52
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-87
Solution
An irregularly shaped crown is weighed in air and then in water with a spring scale. It is to be determined if
the crown is made of pure gold.
Assumptions
1 The buoyancy force in air is negligible. 2 The crown is completely submerged in water.
Properties
We take the density of water to be 1000 kg/m3. The density of gold is given to be 19300 kg/m3.
Analysis
The mass of the crown is
m=
Wair
31.4 N
=
g
9.81 m/s 2
⎛ 1 kg ⋅ m/s 2
⎜
⎜ 1N
⎝
⎞
⎟ = 3.20 kg
⎟
⎠
The difference between the weights in air and in water is due to the buoyancy
force in water, and thus
FB = Wair − W water = 31.4 − 28.9 = 2.50 N
Water
Noting that FB = ρ water gV , the volume of the crown is determined to be
V =
FB
ρ water g
=
2.50 N
3
2
(1000 kg/m )(9.81 m/s )
Air
Crown,
m, V
= 2.548 × 10 − 4 m 3
Then the density of the crown becomes
ρ=
FB
Wwater = 2.95 kgf
Wwir = 3.20 kgf
3.20 kg
m
=
= 12,560 kg/m 3
V 2.548 ×10 − 4 m 3
which is considerably less than the density of gold. Therefore, the crown is NOT made of pure gold.
Discussion
This problem can also be solved without doing any under-water weighing as follows: We would weigh a
bucket half-filled with water, and drop the crown into it. After marking the new water level, we would take the crown out,
and add water to the bucket until the water level rises to the mark. We would weigh the bucket again. Dividing the weight
difference by the density of water and g will give the volume of the crown. Knowing both the weight and the volume of the
crown, the density can easily be determined.
3-53
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-88
Solution
The average density of a person is determined by weighing the person in air and then in water. A relation is
to be obtained for the volume fraction of body fat in terms of densities.
Assumptions 1 The buoyancy force in air is negligible. 2 The body is considered to consist of fat and muscle only. 3 The
body is completely submerged in water, and the air volume in the lungs is negligible.
Analysis
The difference between the weights of the person in air and in
water is due to the buoyancy force in water. Therefore,
FB = Wair − W water
→ ρ water gV = W air − W water
Knowing the weights and the density of water, the relation above gives the volume of
the person. Then the average density of the person can be determined from
m W /g
ρ ave = = air
V
V
Under assumption #2, the total mass of a person is equal to the sum of the masses of the fat and muscle tissues, and the
total volume of a person is equal to the sum of the volumes of the fat and muscle tissues. The volume fraction of body fat is
the ratio of the fat volume to the total volume of the person. Therefore,
V = V fat + V muscle where V fat = x fatV
m = m fat + m muscle
and
V muscle = x muscleV = (1 - x fat )V
Water
Air
Noting that mass is density times volume, the last relation can be written as
ρ aveV = ρ fatV fat + ρ muscleV muscle
ρ aveV = ρ fat x fatV + ρ muscle (1 − x fat )V
Person,
m,V
Canceling the V and solving for xfat gives the desired relation,
xfat =
ρ muscle − ρ avg
ρ muscle − ρfat
Wwater
Wair
Discussion
Weighing a person in water in order to determine its volume is
not practical. A more practical way is to use a large container, and measuring
the change in volume when the person is completely submerged in it.
3-54
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-89
Solution
The volume of the hull of a boat is given. The amounts of load the boat can carry in a lake and in the sea
are to be determined.
Assumptions
1 The dynamic effects of the waves are disregarded. 2 The buoyancy force in air is negligible.
Properties
kg/m3.
The density of sea water is given to be 1.03×1000 = 1030 kg/m3. We take the density of water to be 1000
Analysis
The weight of the unloaded boat is
⎛
1 kN
Wboat = mg = (8560 kg)(9.81 m/s 2 )⎜
⎜ 1000 kg ⋅ m/s 2
⎝
⎞
⎟ = 84.0 kN
⎟
⎠
The buoyancy force becomes a maximum when the entire hull of the boat is submerged
in water, and is determined to be
⎛
⎞
1 kN
⎟ = 1472 kN
FB ,lake = ρ lake gV = (1000 kg/m 3 )(9.81 m/s 2 )(150 m 3 )⎜⎜
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠
⎛
⎞
1 kN
⎟ = 1516 kN T
FB,sea = ρ sea gV = (1030 kg/m 3 )(9.81 m/s 2 )(150 m 3 )⎜⎜
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠
he total weight of a floating boat (load + boat itself) is equal to the buoyancy
force. Therefore, the weight of the maximum load is
Wload
FB
Wboat
Wload, lake = FB , lake − Wboat = 1472 − 84 = 1388 kN
Wload, sea = FB ,sea − W boat = 1516 − 84 = 1432 kN
The corresponding masses of load are
mload,lake =
mload,sea =
Wload,lake
g
Wload,lsea
g
=
=
1388 kN ⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
9.81 m/s 2 ⎝
⎞
⎟ = 141,500 kg ≅ 142,000 kg
⎠
1432 kN ⎛ 1000 kg ⋅ m/s 2 ⎞
⎜
⎟ = 145,970 kg ≅ 146,000 kg
1 kN
9.81 m/s 2 ⎝
⎠
Discussion
Note that this boat can carry nearly 4500 kg more load in the sea than it can in fresh water. Fully-loaded
boats in sea water should expect to sink into water deeper when they enter fresh water, such as a river where the port may
be.
3-55
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
Fluids in Rigid-Body Motion
3-90C
Solution
We are to discuss when a fluid can be treated as a rigid body.
Analysis
A moving body of fluid can be treated as a rigid body when there are no shear stresses (i.e., no motion
between fluid layers relative to each other) in the fluid body.
Discussion
When there is no relative motion between fluid particles, there are no viscous stresses, and pressure (normal
stress) is the only stress.
3-91C
Solution
Analysis
zero.
We are to compare the pressure at the bottom of a glass of water moving at various velocities.
The water pressure at the bottom surface is the same for all cases since the acceleration for all four cases is
Discussion
When any body, fluid or solid, moves at constant velocity, there is no acceleration, regardless of the
direction of the movement.
3-92C
Solution
We are to compare the pressure in a glass of water for stationary and accelerating conditions.
Analysis
The pressure at the bottom surface is constant when the glass is stationary. For a glass moving on a
horizontal plane with constant acceleration, water will collect at the back but the water depth will remain constant at the
center. Therefore, the pressure at the midpoint will be the same for both glasses. But the bottom pressure will be low at
the front relative to the stationary glass, and high at the back (again relative to the stationary glass). Note that the
pressure in all cases is the hydrostatic pressure, which is directly proportional to the fluid height.
Discussion
We ignore any sloshing of the water.
3-93C
Solution
We are to analyze the pressure in a glass of water that is rotating.
Analysis
When a vertical cylindrical container partially filled with water is rotated about its axis and rigid body
motion is established, the fluid level will drop at the center and rise towards the edges. Noting that hydrostatic pressure is
proportional to fluid depth, the pressure at the mid point will drop and the pressure at the edges of the bottom surface
will rise due to the rotation.
Discussion
The highest pressure occurs at the bottom corners of the container.
3-56
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-94
Solution
A water tank is being towed by a truck on a level road, and the angle the free surface makes with the
horizontal is measured. The acceleration of the truck is to be determined.
ax
Assumptions 1 The road is horizontal so that acceleration has no vertical component (az = 0).
2 Effects of splashing, breaking, driving over bumps, and climbing hills are assumed to be
secondary, and are not considered. 3 The acceleration remains constant.
θ = 15°
Analysis
We take the x-axis to be the direction of motion, the z-axis to be the upward
vertical direction. The tangent of the angle the free surface makes with the horizontal is
Water
ax
tan θ =
tank
g+a
z
Solving for ax and substituting,
a x = ( g + a z ) tan θ = (9.81 m/s 2 + 0) tan 15° = 2.63 m/s 2
Discussion
Note that the analysis is valid for any fluid with constant density since we used no information that pertains
to fluid properties in the solution.
3-95
Solution
Two water tanks filled with
water, one stationary and the other moving
upwards at constant acceleration. The tank with
the higher pressure at the bottom is to be
determined.
8
Assumptions 1 The acceleration remains
constant. 2 Water is an incompressible
substance.
Tank A
•
Tank B
2
az = 5
z
Water
•
Properties
We take the density of water to
be 1000 kg/m3.
•
2
1
Water
0
2
•
g
1
The pressure difference between two points 1 and 2 in an incompressible fluid is given by
Analysis
P2 − P1 = − ρa x ( x 2 − x1 ) − ρ ( g + a z )( z 2 − z1 )
or
P1 − P2 = ρ ( g + a z )( z 2 − z1 )
since ax = 0. Taking point 2 at the free surface and point 1 at the tank bottom, we have P2 = Patm and z 2 − z1 = h and thus
P1, gage = Pbottom = ρ ( g + a z )h
Tank A: We have az = 0, and thus the pressure at the bottom is
PA,
bottom
⎛
1 kN
= ρgh A = (1000 kg/m 3 )(9.81 m/s 2 )(8 m)⎜⎜
1000
kg ⋅ m/s 2
⎝
⎞
⎟ = 78.5 kN/m 2
⎟
⎠
Tank B: We have az = +5 m/s2, and thus the pressure at the bottom is
⎛
1 kN
= ρ ( g + a z )h B = (1000 kg/m 3 )(9.81 + 5 m/s 2 )(2 m)⎜⎜
1000
kg ⋅ m/s 2
⎝
Therefore, tank A has a higher pressure at the bottom.
PB ,
bottom
⎞
⎟ = 29.6 kN/m 2
⎟
⎠
Discussion
We can also solve this problem quickly by examining the relation Pbottom = ρ ( g + a z )h . Acceleration for
tank B is about 1.5 times that of Tank A (14.81 vs 9.81 m/s2), but the fluid depth for tank A is 4 times that of tank B (8 m
vs 2 m). Therefore, the tank with the larger acceleration-fluid height product (tank A in this case) will have a higher
pressure at the bottom.
3-57
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-96
Solution
A water tank is being towed on an uphill road at constant acceleration. The angle the free surface of water
makes with the horizontal is to be determined, and the solution is to be repeated for the downhill motion case.
Uphill
motion
Horizontal
G
g
Downhill
motion
G
g
Free
surface
θ
az
Water
tank
G
a = 5 m/s 2
ax
-θ
G
a = 5 m/s 2
az
ax
z
z
α = 20°
α = 20°
x
x
Assumptions 1 Effects of splashing, breaking, driving over bumps, and climbing hills are assumed to be secondary, and
are not considered. 2 The acceleration remains constant.
Analysis
We take the x- and z-axes as shown in the figure. From geometrical considerations, the horizontal and
vertical components of acceleration are
a x = a cos α
a z = a sin α
The tangent of the angle the free surface makes with the horizontal is
tan θ =
ax
(5 m/s 2 ) cos 20°
a cos α
=
=
= 0.4078
g + a z g + a sin α 9.81 m/s 2 + (5 m/s 2 ) sin 20°
→
θ = 22.2°
When the direction of motion is reversed, both ax and az are in negative x- and z-direction, respectively, and thus become
negative quantities,
a x = − a cos α
a z = −a sin α
Then the tangent of the angle the free surface makes with the horizontal becomes
tan θ =
ax
− (5 m/s 2 ) cos 20°
a cos α
=
=
= −0.5801
g + a z g + a sin α 9.81 m/s 2 − (5 m/s 2 ) sin 20°
→
θ = - 30.1°
Discussion
Note that the analysis is valid for any fluid with constant density, not just water, since we used no
information that pertains to water in the solution.
3-58
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-97E
Solution
A vertical cylindrical tank open to the atmosphere is rotated about the centerline. The angular velocity at
which the bottom of the tank will first be exposed, and the maximum water height at this moment are to be determined.
ω
2 ft
z
0
r
Assumptions 1 The increase in the rotational speed is very slow so that the liquid in the container always acts as a rigid
body. 2 Water is an incompressible fluid.
Analysis
Taking the center of the bottom surface of the rotating vertical cylinder as the origin (r = 0, z = 0), the
equation for the free surface of the liquid is given as
z s ( r ) = h0 −
ω2
4g
( R 2 − 2r 2 )
where h0 = 1 ft is the original height of the liquid before rotation. Just before dry spot appear at the center of bottom
surface, the height of the liquid at the center equals zero, and thus zs(0) = 0. Solving the equation above for ω and
substituting,
ω=
4 gh0
=
R2
4 ( 32.2 ft/s 2 ) (1 ft )
(1 ft )
2
= 11.35 rad/s ≅ 11.4 rad/s
Noting that one complete revolution corresponds to 2π radians, the rotational speed of the container can also be expressed
in terms of revolutions per minute (rpm) as
n =
ω 11.35 rad/s ⎛ 60 s ⎞
=
⎜
⎟ = 108 rpm
2π 2π rad/rev ⎝ 1 min ⎠
Therefore, the rotational speed of this container should be limited to 108 rpm to avoid any dry spots at the bottom surface
of the tank.
The maximum vertical height of the liquid occurs a the edges of the tank (r = R = 1 ft), and it is
z s ( R ) = h0 +
Discussion
property.
ω2R2
4g
= (1 ft ) +
(11.35 rad/s) 2 (1 ft) 2
4(32.2 ft/s 2 )
= 2.00 ft
Note that the analysis is valid for any liquid since the result is independent of density or any other fluid
3-59
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-98
Solution
A cylindrical tank is being transported on a level road at constant acceleration. The allowable water height
to avoid spill of water during acceleration is to be determined.
ax = 4 m/s2
Δz
θ
htank =60 cm
Water
tank
D=40 cm
Assumptions 1 The road is horizontal during acceleration so that acceleration has no vertical component (az = 0). 2
Effects of splashing, breaking, driving over bumps, and climbing hills are assumed to be secondary, and are not considered.
3 The acceleration remains constant.
Analysis
We take the x-axis to be the direction of motion, the z-axis to be the upward vertical direction, and the
origin to be the midpoint of the tank bottom. The tangent of the angle the free surface makes with the horizontal is
ax
4
=
= 0.4077 (and thus θ = 22.2°)
g + a z 9.81 + 0
The maximum vertical rise of the free surface occurs at the back of the tank, and the vertical midplane experiences no rise
or drop during acceleration. Then the maximum vertical rise at the back of the tank relative to the midplane is
tan θ =
Δz max = ( D / 2) tan θ = [(0.40 m)/2] × 0.4077 = 0.082 m = 8.2 cm
Therefore, the maximum initial water height in the tank to avoid spilling is
hmax = htank − Δz max = 60 − 8.2 = 51.8 cm
Discussion
Note that the analysis is valid for any fluid with constant density, not just water, since we used no
information that pertains to water in the solution.
3-60
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-99
Solution
A vertical cylindrical container partially filled with a liquid is rotated at constant speed. The drop in the
liquid level at the center of the cylinder is to be determined.
ω
Free
surface
ho = 60 cm
zs
z
r
g
R = 20 cm
Assumptions 1 The increase in the rotational speed is very slow so that the liquid in the container always acts as a rigid
body. 2 The bottom surface of the container remains covered with liquid during rotation (no dry spots).
Analysis
Taking the center of the bottom surface of the rotating vertical cylinder as the origin (r = 0, z = 0), the
equation for the free surface of the liquid is given as
z s ( r ) = h0 −
ω2
4g
( R 2 − 2r 2 )
where h0 = 0.6 m is the original height of the liquid before rotation, and
ω = 2πn = 2π (120 rev/min)⎛⎜
1 min ⎞
⎟ = 12.57 rad/s
⎝ 60 s ⎠
Then the vertical height of the liquid at the center of the container where r = 0 becomes
z s ( 0 ) = h0 −
ω 2R2
4g
= (0.60 m ) −
(12.57 rad/s) 2 (0.20 m) 2
4(9.81 m/s 2 )
= 0.44 m
Therefore, the drop in the liquid level at the center of the cylinder is
Δhdrop, center = h0 − z s (0) = 0.60 − 0.44 = 0.16 m
Discussion
Note that the analysis is valid for any liquid since the result is independent of density or any other fluid
property. Also, our assumption of no dry spots is validated since z0(0) is positive.
3-61
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-100
Solution
The motion of a fish tank in the cabin of an elevator is considered. The pressure at the bottom of the tank
when the elevator is stationary, moving up with a specified acceleration, and moving down with a specified acceleration is
to be determined.
Fish Tank
2
•
az = 3 m/s2
h = 40 cm
z
0
Water
•
g
1
Assumptions
1 The acceleration remains constant. 2 Water is an incompressible substance.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
The pressure difference between two points 1 and 2 in an incompressible fluid is given by
P2 − P1 = − ρa x ( x 2 − x1 ) − ρ ( g + a z )( z 2 − z1 )
or
P1 − P2 = ρ ( g + a z )( z 2 − z1 )
since ax = 0. Taking point 2 at the free surface and point 1 at the tank bottom, we have P2 = Patm and z 2 − z1 = h and thus
P1, gage = Pbottom = ρ ( g + a z )h
(a) Tank stationary: We have az = 0, and thus the gage pressure at the tank bottom is
⎛
1 kN
P bottom = ρgh = (1000 kg/m 3 )(9.81 m/s 2 )(0.4 m)⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟ = 3.92 kN/m 2 = 3.92 kPa
⎟
⎠
(b) Tank moving up: We have az = +3 m/s2, and thus the gage pressure at the tank bottom is
⎛
1 kN
P bottom = ρ ( g + a z )h B = (1000 kg/m 3 )(9.81 + 3 m/s 2 )(0.4 m)⎜⎜
1000
kg ⋅ m/s 2
⎝
⎞
⎟ = 5.12 kN/m 2 = 5.12 kPa
⎟
⎠
(c) Tank moving down: We have az = -3 m/s2, and thus the gage pressure at the tank bottom is
⎛
1 kN
P bottom = ρ ( g + a z )h B = (1000 kg/m 3 )(9.81 − 3 m/s 2 )(0.4 m)⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟ = 2.72 kN/m 2 = 2.72 kPa
⎟
⎠
Discussion
Note that the pressure at the tank bottom while moving up in an elevator is almost twice that while moving
down, and thus the tank is under much greater stress during upward acceleration.
3-62
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-101
Solution
A vertical cylindrical milk tank is rotated at constant speed, and the pressure at the center of the bottom
surface is measured. The pressure at the edge of the bottom surface is to be determined.
ω
Free
surface
zs
ho
z
0
g
r
R = 1.50 m
Assumptions 1 The increase in the rotational speed is very slow so that the liquid in the container always acts as a rigid
body. 2 Milk is an incompressible substance.
Properties
The density of the milk is given to be 1030 kg/m3.
Analysis
Taking the center of the bottom surface of the rotating vertical cylinder as the origin (r = 0, z = 0), the
equation for the free surface of the liquid is given as
z s ( r ) = h0 −
ω2
4g
( R 2 − 2r 2 )
where R = 1.5 m is the radius, and
⎛ 1 min ⎞
⎟ = 1.2566 rad/s
⎝ 60 s ⎠
ω = 2πn = 2π (12 rev/min)⎜
The fluid rise at the edge relative to the center of the tank is
⎛
ω 2R2
Δh = z s ( R ) − z s (0) = ⎜⎜ h0 +
4g
⎝
2 2
⎞ ⎛
⎟ − ⎜ h0 − ω R
⎟ ⎜
4g
⎠ ⎝
⎞ ω 2 R 2 (1.2566 rad/s) 2 (1.50 m) 2
⎟=
=
= 1.1811 m
⎟
2g
2(9.81 m/s 2 )
⎠
The pressure difference corresponding to this fluid height difference is
⎛
1 kN
ΔP bottom = ρgΔh = (1030 kg/m 3 )(9.81 m/s 2 )(1.1811 m)⎜
⎜ 1000 kg ⋅ m/s 2
⎝
⎞
⎟ = 1.83 kN/m 2 = 1.83 kPa
⎟
⎠
Then the pressure at the edge of the bottom surface becomes
Pbottom, edge = Pbottom, center + ΔPbottom = 130 + 1.83 = 131.83 kPa ≅ 132 kPa
Discussion
Note that the pressure is 1.4% higher at the edge relative to the center of the tank, and there is a fluid level
difference of 1.18 m between the edge and center of the tank, and these differences should be considered when designing
rotating fluid tanks.
3-63
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-102
Solution
Milk is transported in a completely filled horizontal cylindrical tank accelerating at a specified rate. The
maximum pressure difference in the tanker is to be determined.
ax = - 3 m/s2
•
1
z
x
0
•
2
g
Assumptions
1 The acceleration remains constant. 2 Milk is an incompressible substance.
Properties
The density of the milk is given to be 1020 kg/m3.
Analysis
We take the x- and z- axes as shown. The horizontal acceleration is in the negative x direction, and thus ax
is negative. Also, there is no acceleration in the vertical direction, and thus az = 0. The pressure difference between two
points 1 and 2 in an incompressible fluid in linear rigid body motion is given by
P2 − P1 = − ρa x ( x 2 − x1 ) − ρ ( g + a z )( z 2 − z1 )
→
P2 − P1 = − ρa x ( x 2 − x1 ) − ρg ( z 2 − z1 )
The first term is due to acceleration in the horizontal direction and the resulting compression effect towards the back of the
tanker, while the second term is simply the hydrostatic pressure that increases with depth. Therefore, we reason that the
lowest pressure in the tank will occur at point 1 (upper front corner), and the higher pressure at point 2 (the lower rear
corner). Therefore, the maximum pressure difference in the tank is
ΔPmax = P2 − P1 = − ρa x ( x 2 − x1 ) − ρg ( z 2 − z1 ) = −[a x ( x 2 − x1 ) + g ( z 2 − z1 )]
[
]
⎛
1 kN
= −(1020 kg/m 3 ) (−2.5 m/s 2 )(7 m) + (9.81 m/s 2 )(−3 m) ⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟
⎟
⎠
= (17.9 + 30.0) kN/m 2 = 47.9 kPa
since x1 = 0, x2 = 7 m, z1 = 3 m, and z2 = 0.
Discussion
Note that the variation of pressure along a horizontal line is due to acceleration in the horizontal direction
while the variation of pressure in the vertical direction is due to the effects of gravity and acceleration in the vertical
direction (which is zero in this case).
3-64
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-103
Solution
Milk is transported in a completely filled horizontal cylindrical tank decelerating at a specified rate. The
maximum pressure difference in the tanker is to be determined.
Assumptions
1 The acceleration remains constant. 2 Milk is an incompressible substance.
Properties
1020 kg/m3.
The density of the milk is given to be
ax = 3 m/s2
g
Analysis
We take the x- and z- axes as shown.
The horizontal deceleration is in the x direction, and
thus ax is positive. Also, there is no acceleration in
the vertical direction, and thus az = 0. The pressure
difference between two points 1 and 2 in an
incompressible fluid in linear rigid body motion is
given by
P2 − P1 = − ρa x ( x 2 − x1 ) − ρ ( g + a z )( z 2 − z1 )
•
z
2
•
1
x
P2 − P1 = − ρa x ( x 2 − x1 ) − ρg ( z 2 − z1 )
→
The first term is due to deceleration in the horizontal direction and the resulting compression effect towards the front of the
tanker, while the second term is simply the hydrostatic pressure that increases with depth. Therefore, we reason that the
lowest pressure in the tank will occur at point 1 (upper front corner), and the higher pressure at point 2 (the lower rear
corner). Therefore, the maximum pressure difference in the tank is
ΔPmax = P2 − P1 = − ρa x ( x 2 − x1 ) − ρg ( z 2 − z1 ) = −[a x ( x 2 − x1 ) + g ( z 2 − z1 )]
[
]
⎛
1 kN
= −(1020 kg/m 3 ) (2.5 m/s 2 )(−7 m) + (9.81 m/s 2 )(−3 m) ⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟
⎟
⎠
= (17.9 + 30.0) kN/m 2 = 47.9 kPa
since x1 = 7 m, x2 = 0, z1 = 3 m, and z2 = 0.
Discussion
Note that the variation of pressure along a horizontal line is due to acceleration in the horizontal direction
while the variation of pressure in the vertical direction is due to the effects of gravity and acceleration in the vertical
direction (which is zero in this case).
3-104
Solution
A vertical U-tube partially filled with
alcohol is rotated at a specified rate about one of its arms.
The elevation difference between the fluid levels in the two
arms is to be determined.
Assumptions
z
1 Alcohol is an incompressible fluid.
Analysis
Taking the base of the left arm of the U-tube
as the origin (r = 0, z = 0), the equation for the free surface
of the liquid is given as
z s ( r ) = h0 −
ω2
4g
( R 2 − 2r 2 )
where h0 = 0.20 m is the original height of the liquid before rotation,
and ω = 4.2 rad/s. The fluid rise at the right arm relative to the fluid
level in the left arm (the center of rotation) is
⎛
ω2R2
Δh = z s ( R ) − z s (0) = ⎜⎜ h0 +
4g
⎝
Discussion
h0 =
20 cm
⎞ ⎛
ω2R2
⎟ − ⎜ h0 −
⎟ ⎜
4g
⎠ ⎝
0
r
R = 25 cm
⎞ ω 2 R 2 (4.2 rad/s) 2 (0.25 m) 2
⎟=
=
= 0.056 m
⎟
2g
2(9.81 m/s 2 )
⎠
The analysis is valid for any liquid since the result is independent of density or any other fluid property.
3-65
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-105
Solution
A vertical cylindrical tank is completely filled with gasoline, and the tank is rotated about its vertical axis at
a specified rate. The pressures difference between the centers of the bottom and top surfaces, and the pressures difference
between the center and the edge of the bottom surface are to be determined.
D = 1.20 m
h=3m
z
0
r
Assumptions 1 The increase in the rotational speed is very slow so that the liquid in the container always acts as a rigid
body. 2 Gasoline is an incompressible substance.
Properties
The density of the gasoline is given to be 740 kg/m3.
Analysis
is given by
The pressure difference between two points 1 and 2 in an incompressible fluid rotating in rigid body motion
P2 − P1 =
ρω 2
(r22 − r12 ) − ρg ( z 2 − z1 )
2
where R = 0.60 m is the radius, and
1 min ⎞
ω = 2πn = 2π (70 rev/min)⎛⎜
⎟ = 7.330 rad/s
⎝ 60 s ⎠
(a) Taking points 1 and 2 to be the centers of the bottom and top surfaces, respectively, we have r1 = r2 = 0 and
z 2 − z1 = h = 3 m . Then,
Pcenter, top − Pcenter, bottom = 0 − ρg ( z 2 − z1 ) = − ρgh
⎛
1 kN
= −(740 kg/m 3 )(9.81 m/s 2 )(3 m)⎜⎜
1000
kg ⋅ m/s 2
⎝
⎞
⎟ = 21.8 kN/m 2 = 21.8 kPa
⎟
⎠
(b) Taking points 1 and 2 to be the center and edge of the bottom surface, respectively, we have r1 = 0 , r2 = R , and
z 2 = z1 = 0 . Then,
Pedge, bottom − Pcenter, bottom =
ρω 2
( R 22 − 0) − 0 =
ρω 2 R 2
2
2
3
2
(740 kg/m )(7.33 rad/s) (0.60 m) 2
=
2
⎛
1 kN
⎜
⎜ 1000 kg ⋅ m/s 2
⎝
⎞
⎟ = 7.16 kN/m 2 = 7.16 kPa
⎟
⎠
Discussion
Note that the rotation of the tank does not affect the pressure difference along the axis of the tank. But the
pressure difference between the edge and the center of the bottom surface (or any other horizontal plane) is due entirely to
the rotation of the tank.
3-66
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-106
Solution
The previous problem is reconsidered. The effect of rotational speed on the pressure difference between the
center and the edge of the bottom surface of the cylinder as the rotational speed varies from 0 to 500 rpm in increments of
50 rpm is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
g=9.81 "m/s2"
rho=740 "kg/m3"
R=0.6 "m"
h=3 "m"
omega=2*pi*n_dot/60 "rad/s"
DeltaP_axis=rho*g*h/1000 "kPa"
DeltaP_bottom=rho*omega^2*R^2/2000 "kPa"
Rotation rate
n , rpm
0
50
100
150
200
250
300
350
400
450
500
Angular speed
ω, rad/s
0.0
5.2
10.5
15.7
20.9
26.2
31.4
36.7
41.9
47.1
52.4
ΔPcenter-edge
kPa
0.0
3.7
14.6
32.9
58.4
91.3
131.5
178.9
233.7
295.8
365.2
400
350
ΔP, kPa
300
250
200
150
100
50
0
0
100
200
300
400
500
n, rpm
Discussion
The pressure rise with rotation rate is not linear, but rather quadratic.
3-67
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-107
Solution
A water tank partially filled with water is being towed by a truck on a level road. The maximum
acceleration (or deceleration) of the truck to avoid spilling is to be determined.
ax
Assumptions 1 The road is horizontal so that acceleration has no
vertical component (az = 0). 2 Effects of splashing, breaking, driving
over bumps, and climbing hills are assumed to be secondary, and are
not considered. 3 The acceleration remains constant.
Δh = 2 ft
ax
g + az
→
hw = 6 ft
x
0
a x = g tan θ
L=20 ft
where az = 0 and, from geometric considerations, tanθ is tan θ =
a x = g tan θ = g
Water
tank
z
Analysis
We take the x-axis to be the direction of motion, the zaxis to be the upward vertical direction. The shape of the free surface
just before spilling is shown in figure. The tangent of the angle the free
surface makes with the horizontal is given by
tan θ =
θ
Δh
. Substituting, we get
L/2
Δh
2 ft
= (32.2 ft/s 2 )
= 6.44 m/s 2
L/2
(20 ft)/2
The solution can be repeated for deceleration by replacing ax by – ax. We obtain ax = -6.44 m/s2.
Discussion
Note that the analysis is valid for any fluid with constant density since we used no information that pertains
to fluid properties in the solution.
3-108E
Solution
A water tank partially filled with water is being towed by a truck on a level road. The maximum
acceleration (or deceleration) of the truck to avoid spilling is to be determined.
Assumptions 1 The road is horizontal so that deceleration has no vertical component (az = 0). 2 Effects of splashing and
driving over bumps are assumed to be secondary, and are not considered. 3 The deceleration remains constant.
Analysis
We take the x-axis to be the direction of motion,
the z-axis to be the upward vertical direction. The shape of the
free surface just before spilling is shown in figure. The tangent
of the angle the free surface makes with the horizontal is given
by
tan θ =
−a x
g + az
→
ax
θ
a x = − g tan θ
Water
tank
z
where az = 0 and, from geometric considerations, tanθ is
Δh
tan θ =
L/2
Substituting,
0
Δh
0.5 ft
a x = − g tan θ = − g
= −(32.2 ft/s 2 )
= -4.08 ft/s 2
L/2
(8 ft)/2
Δh = 0.5 ft
hw = 3 ft
x
L= 8 ft
Discussion
Note that the analysis is valid for any fluid with constant density since we used no information that pertains
to fluid properties in the solution.
3-68
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-109
Solution
Water is transported in a completely filled horizontal cylindrical tanker accelerating at a specified rate. The
pressure difference between the front and back ends of the tank along a horizontal line when the truck accelerates and
decelerates at specified rates.
ax = - 3 m/s2
1
•
0
z
•
2
x
g
Assumptions
1 The acceleration remains constant. 2 Water is an incompressible substance.
Properties
We take the density of the water to be 1000 kg/m3.
Analysis
(a) We take the x- and z- axes as shown. The horizontal acceleration is in the negative x direction, and thus
ax is negative. Also, there is no acceleration in the vertical direction, and thus az = 0. The pressure difference between two
points 1 and 2 in an incompressible fluid in linear rigid body motion is given by
P2 − P1 = − ρa x ( x 2 − x1 ) − ρ ( g + a z )( z 2 − z1 )
→
P2 − P1 = − ρa x ( x 2 − x1 )
since z2 - z1 = 0 along a horizontal line. Therefore, the pressure difference between the front and back of the tank is due to
acceleration in the horizontal direction and the resulting compression effect towards the back of the tank. Then the pressure
difference along a horizontal line becomes
⎛
1 kN
ΔP = P2 − P1 = − ρa x ( x 2 − x1 ) = −(1000 kg/m 3 )(−3 m/s 2 )(7 m)⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟ = 21 kN/m 2 = 21 kPa
⎟
⎠
since x1 = 0 and x2 = 7 m.
(b) The pressure difference during deceleration is determined the way, but ax = 4 m/s2 in this case,
⎛
1 kN
ΔP = P2 − P1 = − ρa x ( x 2 − x1 ) = −(1000 kg/m 3 )(4 m/s 2 )(7 m)⎜⎜
1000
kg ⋅ m/s 2
⎝
⎞
⎟ = −28 kN/m 2 = −28 kPa
⎟
⎠
Discussion
Note that the pressure is higher at the back end of the tank during acceleration, but at the front end during
deceleration (during breaking, for example) as expected.
3-69
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
Review Problems
3-110
Solution
One section of the duct of an air-conditioning system is laid underwater. The upward force the water
exerts on the duct is to be determined.
Assumptions 1 The diameter given is the outer diameter of the duct (or, the thickness of the duct material is negligible). 2
The weight of the duct and the air in is negligible.
Properties
The density of air is given to be ρ = 1.30 kg/m3. We take the density of water to be 1000 kg/m3.
Analysis
Noting that the weight of the duct and the air in it is negligible, the net upward force acting on the duct is
the buoyancy force exerted by water. The volume of the underground section of the duct is
V = AL = (πD 2 / 4) L = [π (0.15 m) 2 /4](20 m) = 0.3534 m 3
Then the buoyancy force becomes
D =15 cm
⎛
1 kN
FB = ρgV = (1000 kg/m )(9.81 m/s )(0.3534 m )⎜
⎜ 1000 kg ⋅ m/s 2
⎝
3
2
3
⎞
⎟ = 3.47 kN
⎟
⎠
L = 20 m
FB
Discussion
The upward force exerted by water on the duct is 3.47 kN, which is equivalent to the weight of a mass of
354 kg. Therefore, this force must be treated seriously.
3-111
Solution
A helium balloon tied to the ground carries 2 people. The acceleration of the balloon when it is first
released is to be determined.
Assumptions
The weight of the cage and the ropes of the balloon is negligible.
Properties
The density of air is given to be ρ = 1.16 kg/m3. The density of helium gas is 1/7th of this.
Analysis
The buoyancy force acting on the balloon is
Vballoon = 4π r 3 / 3 = 4π ( 5 m ) / 3 = 523.6 m3
3
⎛ 1 N
⎞
FB = ρair gVballoon = (1.16 kg/m 3 )(9.81 m/s 2 )(523.6 m 3 ) ⎜
= 5958.4 N
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
The total mass is
Helium
balloon
⎛ 1.16
⎞
kg/m3 ⎟ (523.6 m3 ) = 86.8 kg
mHe = ρ HeV = ⎜
7
⎝
⎠
mtotal = mHe + mpeople = 86.8 + 2 × 70 = 226.8 kg
The total weight is
⎛ 1 N
⎞
W = mtotal g = (226.8 kg)(9.81 m/s 2 ) ⎜
= 2224.9 N
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
Thus the net force acting on the balloon is
Fnet = FB − W = 5958.6 − 2224.9 = 3733.5 N
Then the acceleration becomes
F
3733.5 N ⎛ 1 kg ⋅ m/s 2 ⎞
2
a = net =
⎜
⎟ = 16.5 m/s
mtotal 226.8 kg ⎝ 1 N
⎠
m = 140 kg
Discussion
This is almost twice the acceleration of gravity – aerodynamic drag on the balloon acts quickly to slow
down the acceleration.
3-70
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-112
Solution
The previous problem is reconsidered. The effect of the number of people carried in the balloon on
acceleration is to be investigated. Acceleration is to be plotted against the number of people, and the results are to be
discussed.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
"Given Data:"
rho_air=1.16"[kg/m^3]" "density of air"
g=9.807"[m/s^2]"
d_balloon=10"[m]"
m_1person=70"[kg]"
{NoPeople = 2} "Data suppied in Parametric Table"
"Calculated values:"
rho_He=rho_air/7"[kg/m^3]" "density of helium"
r_balloon=d_balloon/2"[m]"
V_balloon=4*pi*r_balloon^3/3"[m^3]"
m_people=NoPeople*m_1person"[kg]"
m_He=rho_He*V_balloon"[kg]"
m_total=m_He+m_people"[kg]"
"The total weight of balloon and people is:"
W_total=m_total*g"[N]"
"The buoyancy force acting on the balloon, F_b, is equal to the weight of the air displaced by the
balloon."
F_b=rho_air*V_balloon*g"[N]"
"From the free body diagram of the balloon, the balancing vertical forces must equal the product of the
total mass and the vertical acceleration:"
F_b- W_total=m_total*a_up
30
No. People
1
2
3
4
5
6
7
8
9
10
25
20
a up [m /s^2]
Aup [m/s2]
28.19
16.46
10.26
6.434
3.831
1.947
0.5204
-0.5973
-1.497
-2.236
15
10
5
0
-5
1
2
3
4
5
6
7
8
9
10
NoPeople
As expected, the more people, the slower the acceleration. In fact, if more than 7 people are on board, the
Discussion
balloon does not rise at all.
3-71
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-113
Solution
determined.
A balloon is filled with helium gas. The maximum amount of load the balloon can carry is to be
Assumptions
The weight of the cage and the ropes of the balloon is negligible.
Properties
The density of air is given to be ρ = 1.16 kg/m3. The density of
helium gas is 1/7th of this.
Analysis
In the limiting case, the net force acting on the balloon will be zero.
That is, the buoyancy force and the weight will balance each other:
W = mg = FB
mtotal =
Thus,
FB 5958.4 N
=
= 607.4 kg
g
9.81 m/s 2
Helium
balloon
mpeople = mtotal − mHe = 607.4 − 86.8 = 520.6 kg ≅ 521 kg
When the net weight of the balloon and its cargo exceeds the weight of the
Discussion
air it displaces, the balloon/cargo is no longer “lighter than air”, and therefore cannot rise.
3-114E
Solution
m
The pressure in a steam boiler is given in kgf/cm2. It is to be expressed in psi, kPa, atm, and bars.
Analysis
We note that 1 atm = 1.03323 kgf/cm2, 1 atm = 14.696 psi, 1 atm = 101.325 kPa, and 1 atm = 1.01325 bar
(inner cover page of text). Then the desired conversions become:
In atm:
⎛
1 atm
P = (75 kgf/cm 2 )⎜
⎜ 1.03323 kgf/cm 2
⎝
⎞
⎟ = 72.6 atm
⎟
⎠
In psi:
⎛
1 atm
P = (75 kgf/cm 2 ) ⎜
2
⎝ 1.03323 kgf/cm
⎞ ⎛ 14.696 psi ⎞
⎟ = 1067 psi ≅ 1070 psi
⎟⎜
⎠ ⎝ 1 atm ⎠
In kPa:
⎛
⎞ ⎛ 101.325 kPa ⎞
1 atm
P = (75 kgf/cm 2 ) ⎜
⎟ = 7355 kPa ≅ 7360 kPa
2 ⎟⎜
1.03323
kgf/cm
⎝
⎠ ⎝ 1 atm ⎠
In bars:
⎛
⎞ ⎛ 1 .01325 bar ⎞
1 atm
P = (75 kgf/cm 2 ) ⎜
⎟ = 73.55 bar ≅ 73.6 bar
2 ⎟⎜
1.03323
kgf/cm
⎝
⎠ ⎝ 1 atm ⎠
Note that the units atm, kgf/cm2, and bar are almost identical to each other. All final results are given to
Discussion
three significant digits, but conversion ratios are typically precise to at least five significant digits.
3-72
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-115
Solution
A barometer is used to measure the altitude of a plane relative to the ground. The barometric readings at the
ground and in the plane are given. The altitude of the plane is to be determined.
Assumptions
The variation of air density with altitude is negligible.
Properties
The densities of air and mercury are given to be ρair = 1.20 kg/m3 and ρmercury = 13,600 kg/m3.
Analysis
Atmospheric pressures at the location of the plane and the ground level are
Pplane = ( ρ g h) plane
⎞⎛ 1 kPa ⎞
⎛
1N
⎟⎜
⎟
= (13,600 kg/m 3 )(9.81 m/s 2 )(0.690 m)⎜
⎜ 1 kg ⋅ m/s 2 ⎟⎜ 1000 N/m 2 ⎟
⎝
⎠⎝
⎠
= 92.06 kPa
Pground = ( ρ g h) ground
⎛
1N
= (13,600 kg/m 3 )(9.81 m/s 2 )(0.753 m)⎜
⎜ 1 kg ⋅ m/s 2
⎝
= 100.46 kPa
⎞⎛ 1 kPa
⎟⎜
⎟⎜ 1000 N/m 2
⎠⎝
⎞
⎟
⎟
⎠
Taking an air column between the airplane and the ground and writing a force
balance per unit base area, we obtain
Wair / A = Pground − Pplane
h
( ρ g h) air = Pground − Pplane
⎞⎛ 1 kPa ⎞
⎛
1N
⎟ = (100.46 − 92.06) kPa
⎟⎜
(1.20 kg/m 3 )(9.81 m/s 2 )(h)⎜
2
⎜ 1 kg ⋅ m/s ⎟⎜ 1000 N/m 2 ⎟
⎠
⎠⎝
⎝
It yields h = 714 m, which is also the altitude of the airplane.
Discussion
0 Sea level
Obviously, a mercury barometer is not practical on an airplane – an electronic barometer is used instead.
3-116
Solution
A 10-m high cylindrical container is filled with equal volumes of water and oil. The pressure difference
between the top and the bottom of the container is to be determined.
Properties
The density of water is given to be ρ = 1000 kg/m3. The
specific gravity of oil is given to be 0.85.
Analysis
The density of the oil is obtained by multiplying its specific
gravity by the density of water,
Oil
SG = 0.85
ρ = SG × ρ H O = (0.85)(1000 kg/m3 ) = 850 kg/m3
h = 10 m
2
The pressure difference between the top and the bottom of the cylinder
is the sum of the pressure differences across the two fluids,
Water
ΔPtotal = ΔPoil + ΔPwater = ( ρ gh )oil + ( ρ gh ) water
⎛ 1 kPa ⎞
= ⎣⎡(850 kg/m3 )(9.81 m/s 2 )(5 m) + (1000 kg/m3 )(9.81 m/s 2 )(5 m) ⎦⎤ ⎜
2 ⎟
⎝ 1000 N/m ⎠
= 90.7 kPa
Discussion
The pressure at the interface must be the same in the oil and the water. Therefore, we can use the rules for
hydrostatics across the two fluids, since they are at rest and there are no appreciable surface tension effects.
3-73
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-117
Solution
The pressure of a gas contained in a vertical piston-cylinder device is measured to be 500 kPa. The mass of
the piston is to be determined.
Patm
Assumptions
There is no friction between the piston and the cylinder.
Analysis
forces yield
Drawing the free body diagram of the piston and balancing the vertical
W = PA − Patm A
( m ) ( 9.81
mg = ( P − Patm ) A
m/s
2
) = ( 500 − 100
P
kPa ) ( 30 × 10
−4
⎛ 1000 kg/m ⋅ s ⎞
m )⎜
⎟
1 kPa
⎝
⎠
2
W = mg
2
Solution of the above equation yields m = 122 kg.
Discussion
The gas cannot distinguish between pressure due to the piston weight and atmospheric pressure – both
“feel” like a higher pressure acting on the top of the gas in the cylinder.
3-118
Solution
The gage pressure in a pressure cooker is maintained constant at 100 kPa by a petcock. The mass of the
petcock is to be determined.
Assumptions
There is no blockage of the pressure release valve.
Analysis
Atmospheric pressure is acting on all surfaces of the petcock, which balances itself out. Therefore, it can
be disregarded in calculations if we use the gage pressure as the cooker pressure. A force balance on the petcock (ΣFy = 0)
yields
Patm
W = Pgage A
(100 kPa)(4 × 10−6 m 2 ) ⎛ 1000 kg/m ⋅ s 2 ⎞
⎜
⎟
9.81 m/s 2
1 kPa
g
⎝
⎠
= 0.0408 kg = 40.8 g
m=
Pgage A
=
P
The higher pressure causes water in the cooker to boil at a higher temperature.
Discussion
W = mg
3-119
Solution
A glass tube open to the atmosphere is attached to a water pipe, and the pressure at the bottom of the tube is
measured. It is to be determined how high the water will rise in the tube.
Properties
The density of water is given to be ρ = 1000 kg/m3.
Analysis
The pressure at the bottom of the tube can be expressed as
P = Patm + ( ρ g h ) tube
Solving for h,
P − Patm
h=
ρg
Patm= 92 atm
h
Water
⎛ 1 kg ⋅ m/s 2 ⎞ ⎛ 1000 N/m 2 ⎞
(115 − 92) kPa
⎜
⎟
⎜
⎟
(1000 kg/m3 )(9.8 m/s 2 ) ⎝ 1 N
⎠ ⎝ 1 kPa ⎠
= 2.35 m
Discussion
Even though the water is flowing, the water in the tube itself is at rest. If the pressure at the tube bottom had
been given in terms of gage pressure, we would not have had to take into account the atmospheric pressure term.
=
3-74
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-120
Solution
The average atmospheric pressure is given as Patm = 101.325 (1 − 0.02256 z )
5.256
where z is the altitude in
km. The atmospheric pressures at various locations are to be determined.
Analysis
Atmospheric pressure at various locations is obtained by substituting the altitude z values in km into the
. (1 − 0.02256z )5.256 . The results are tabulated below.
relation Patm = 101325
Atlanta:
Denver:
M. City:
Mt. Ev.:
Discussion
(z = 0.306 km): Patm = 101.325(1 - 0.02256×0.306)5.256 = 97.7 kPa
(z = 1.610 km): Patm = 101.325(1 - 0.02256×1.610)5.256 = 83.4 kPa
(z = 2.309 km): Patm = 101.325(1 - 0.02256×2.309)5.256 = 76.5 kPa
(z = 8.848 km): Patm = 101.325(1 - 0.02256×8.848)5.256 = 31.4 kPa
It may be surprising, but the atmospheric pressure on Mt. Everest is less than 1/3 that at sea level!
3-121
Solution
The air pressure in a duct is measured by an inclined manometer. For a given vertical level difference, the
gage pressure in the duct and the length of the differential fluid column are to be determined.
Assumptions
The manometer fluid is an incompressible substance.
Properties
The density of the liquid is given to be ρ = 0.81 kg/L = 810 kg/m3.
Analysis
The gage pressure in the duct is determined from
Pgage = Pabs − Patm = ρ gh
⎛ 1N
⎞ ⎛ 1 Pa ⎞
= (810 kg/m3 )(9.81 m/s 2 )(0.08 m) ⎜
⎟
2 ⎟⎜
1 kg ⋅ m/s ⎠ ⎝ 1N/m 2 ⎠
⎝
= 636 Pa
The length of the differential fluid column is
Air
L
L = h / sinθ = ( 8 cm ) / sin35° = 13.9 cm
8 cm
35°
Discussion
Note that the length of the differential fluid column is extended considerably by inclining the manometer
arm for better readability (and therefore higher precision).
3-122E
Solution
Equal volumes of water and oil are poured into a U-tube from different arms, and the oil side is pressurized
until the contact surface of the two fluids moves to the bottom and the liquid levels in both arms become the same. The
excess pressure applied on the oil side is to be determined.
Assumptions 1 Both water and oil are incompressible substances. 2 Oil does not mix with water. 3 The cross-sectional
area of the U-tube is constant.
Properties
The density of oil is given to be ρoil = 49.3 lbm/ft3. We take the density of water to be ρw = 62.4 lbm/ft3.
Analysis
Noting that the pressure of both the water and the oil is the same
at the contact surface, the pressure at this surface can be expressed as
Pcontact = Pblow + ρ a gha = Patm + ρ w gh w
Water
Noting that ha = hw and rearranging,
Blown
air
Oil
Pgage, blow = Pblow − Patm = ( ρ w − ρoil ) gh
⎛
⎞ ⎛ 1 ft 2 ⎞
1 lbf
= ( 62.4- 49.3 lbm/ft 3 )( 32.2 ft/s 2 ) ( 30/12 ft ) ⎜
⎟
⎜
⎟
32.2 lbm ⋅ ft/s 2 ⎠ ⎝ 144 in 2 ⎠
⎝
= 0.227 psi
30 in
Discussion
When the person stops blowing, the oil rises and some water flows into the right arm. It can be shown that
when the curvature effects of the tube are disregarded, the differential height of water is 23.7 in to balance 30-in of oil.
3-75
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-123
Solution
It is given that an IV fluid and the blood pressures balance each other when the bottle is at a certain height,
and a certain gage pressure at the arm level is needed for sufficient flow rate. The gage pressure of the blood and elevation
of the bottle required to maintain flow at the desired rate are to be determined.
Assumptions
1 The IV fluid is incompressible. 2 The IV bottle is open to the atmosphere.
Properties
The density of the IV fluid is given to be ρ = 1020 kg/m3.
Analysis
(a) Noting that the IV fluid and the blood pressures balance each other when the bottle is 1.2 m above the
arm level, the gage pressure of the blood in the arm is simply equal to the gage pressure of the IV fluid at a depth of 1.2 m,
Pgage, arm = Pabs − Patm = ρgharm- bottle
Patm
⎛
1 kN
= (1020 kg/m 3 )(9.81 m/s 2 )(1.20 m)⎜
⎜ 1000 kg ⋅ m/s 2
⎝
= 12.0 kPa
⎞⎛ 1 kPa
⎟⎜
⎟⎜ 1 kN/m 2
⎠⎝
⎞
⎟
⎟
⎠
(b) To provide a gage pressure of 20 kPa at the arm level, the height of the bottle from
the arm level is again determined from Pgage, arm = ρgharm- bottle to be
harm- bottle =
=
IV
Bottle
1.2 m
Pgage, arm
ρg
⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
(1020 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
20 kPa
⎞⎛ 1 kN/m 2
⎟⎜
⎟⎜ 1 kPa
⎠⎝
⎞
⎟ = 2.0 m
⎟
⎠
Discussion
Note that the height of the reservoir can be used to control flow rates in gravity driven flows. When there is
flow, the pressure drop in the tube due to friction should also be considered. This will result in raising the bottle a little
higher to overcome pressure drop.
3-76
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-124
Solution
A gasoline line is connected to a pressure gage through a double-U manometer. For a given reading of the
pressure gage, the gage pressure of the gasoline line is to be determined.
Assumptions
1 All the liquids are incompressible. 2 The effect of air column on pressure is negligible.
Properties
The specific gravities of oil, mercury, and gasoline are given to be 0.79, 13.6, and 0.70, respectively. We
take the density of water to be ρw = 1000 kg/m3.
Analysis
Starting with the pressure indicated by the pressure gage and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms until we reach the gasoline pipe, and setting the result equal to Pgasoline
gives
Pgage − ρ w ghw + ρoil ghoil − ρ Hg ghHg − ρ gasoline ghgasoline = Pgasoline
Rearranging,
Pgasoline = Pgage − ρ w g( hw − SGoil hoil + SGHg hHg + SGgasoline hgasoline )
Substituting,
Pgasoline = 370 kPa -(1000 kg/m3 )(9.81 m/s 2 )[(0.45 m) − 0.79( 0.5 m) + 13.6( 0.1 m) + 0.70( 0.22 m)]
⎛
⎞ ⎛ 1 kPa ⎞
1 kN
×⎜
2 ⎟⎜
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠ ⎝ 1 kN/m ⎠
= 354.6 kPa ≅ 355 kPa
Therefore, the pressure in the gasoline pipe is 15.4 kPa lower than the pressure reading of the pressure gage.
Pgage = 370 kPa
Oil
45 cm
Gasoline
Air
22 cm
50 cm
10 cm
Water
Mercury
Note that sometimes the use of specific gravity offers great convenience in the solution of problems that
Discussion
involve several fluids.
3-77
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-125
Solution
A gasoline line is connected to a pressure gage through a double-U manometer. For a given reading of the
pressure gage, the gage pressure of the gasoline line is to be determined.
Assumptions
1 All the liquids are incompressible. 2 The effect of air column on pressure is negligible.
Properties
The specific gravities of oil, mercury, and gasoline are given to be 0.79, 13.6, and 0.70, respectively. We
take the density of water to be ρw = 1000 kg/m3.
Analysis
Starting with the pressure indicated by the pressure gage and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms until we reach the gasoline pipe, and setting the result equal to Pgasoline
gives
Pgage − ρ w gh w + ρ alcohol ghalcohol − ρ Hg ghHg − ρ gasoline ghgasoline = Pgasoline
Rearranging,
Pgasoline = Pgage − ρ w g (h w − SG alcohol hs,alcohol + SG Hg hHg + SG gasoline hs,gasoline )
Substituting,
Pgasoline = 240 kPa -(1000 kg/m3 )(9.81 m/s 2 )[(0.45 m) − 0.79( 0.5 m) + 13.6( 0.1 m) + 0.70( 0.22 m)]
⎛
⎞ ⎛ 1 kPa ⎞
1 kN
×⎜
2 ⎟⎜
2 ⎟
⋅
1000
kg
m/s
⎝
⎠ ⎝ 1 kN/m ⎠
= 224.6 kPa ≅ 225 kPa
Therefore, the pressure in the gasoline pipe is 15.4 kPa lower than the pressure reading of the pressure gage.
Pgage = 240 kPa
Oil
45 cm
Gasoline
Air
22 cm
50 cm
10 cm
Water
Mercury
Note that sometimes the use of specific gravity offers great convenience in the solution of problems that
Discussion
involve several fluids.
3-78
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-126E
Solution
A water pipe is connected to a double-U manometer whose free arm is open to the atmosphere. The
absolute pressure at the center of the pipe is to be determined.
Assumptions
1 All the liquids are incompressible. 2 The solubility of the liquids in each other is negligible.
Properties
The specific gravities of mercury and oil are given to be 13.6 and 0.80, respectively. We take the density of
water to be ρw = 62.4 lbm/ft3.
Analysis
Starting with the pressure at the center of the water pipe, and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms until we reach the free surface of oil where the oil tube is exposed to the
atmosphere, and setting the result equal to Patm gives
Pwater pipe − ρ water gh water + ρ alcohol ghalcohol − ρ Hg ghHg − ρ oil ghoil = Patm
Solving for Pwater
pipe,
Pwater pipe = Patm + ρ water g (h water − SG oil halcohol + SG Hg hHg + SG oil hoil )
Substituting,
Pwater pipe = 14.2 psia + (62.4 lbm/ft 3 )(32.2 ft/s 2 )[(35/12 ft) − 0.80(60/12 ft) + 13.6(15/12 ft)
⎛
1 lbf
+ 0.8(40/12 ft)] × ⎜
⎜ 32.2 lbm ⋅ ft/s 2
⎝
= 22.3 psia
⎞⎛ 1 ft 2
⎟⎜
⎟⎜ 144 in 2
⎠⎝
⎞
⎟
⎟
⎠
Therefore, the absolute pressure in the water pipe is 22.3 psia.
Oil
Oil
35 in
40 in
60 in
15 in
Water
Mercury
Note that jumping horizontally from one tube to the next and realizing that pressure remains the same in the
Discussion
same fluid simplifies the analysis greatly.
3-79
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-127
Solution
The pressure of water flowing through a pipe is measured by an arrangement that involves both a pressure
gage and a manometer. For the values given, the pressure in the pipe is to be determined.
Assumptions
1 All the liquids are incompressible. 2 The effect of air column on pressure is negligible.
Properties
kg/m3.
The specific gravity of gage fluid is given to be 2.4. We take the standard density of water to be ρw = 1000
Analysis
Starting with the pressure indicated by the pressure gage and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms until we reach the water pipe, and setting the result equal to Pwater give
Pgage + ρ w gh w1 − ρ gage ghgage − ρ w gh w2 = Pwater
Rearranging,
Pwater = Pgage + ρ w g ( hw1 − SG gage hgage − hw2 ) = Pgage + ρ w g ( h2 − SG gage L1sinθ − L2sinθ )
Noting that sin θ = 8 / 12 = 0.6667 and substituting,
Pwater = 30 kPa + (1000 kg/m 3 )(9.81 m/s 2 )[(0.50 m) − 2.4(0.06 m)0.6667 − (0.06 m)0.6667]
⎛
1 kN
× ⎜⎜
1000
kg ⋅ m/s 2
⎝
= 33.6 kPa
⎞⎛ 1 kPa ⎞
⎟⎜
⎟⎝ 1 kN/m 2 ⎟⎠
⎠
Therefore, the pressure in the gasoline pipe is 3.6 kPa over the reading of the pressure gage.
P0=30 kPa
Air
Pipe
Water
Water
h2 = 50 cm
150C
L2=6 cm
h1 =8 cm
θ
L1=6 cm
Gage fluid
SG=2.4
Discussion
Note that even without a manometer, the reading of a pressure gage can be in error if it is not placed at the
same level as the pipe when the fluid is a liquid.
3-80
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-128
Solution
A U-tube filled with mercury except the 18-cm high portion at the top. Oil is poured into the left arm,
forcing some mercury from the left arm into the right one. The maximum amount of oil that can be added into the left arm
is to be determined.
Assumptions
1 Both liquids are incompressible. 2 The U-tube is perfectly vertical.
Properties
The specific gravities are given to be 2.72 for oil and 13.6 for mercury.
Analysis
Initially, the mercury levels in both tubes are the same. When oil is poured into the left arm, it will push the
mercury in the left down, which will cause the mercury level in the right arm to rise. Noting that the volume of mercury is
constant, the decrease in the mercury volume in left column must be equal to the increase in the mercury volume in the
right arm. Therefore, if the drop in mercury level in the left arm is x, the rise in the mercury level in the right arm h
corresponding to a drop of x in the left arm is
V left = V right
→
π (2d ) 2 x = πd 2 h
h = 4x
→
The pressures at points A and B are equal PA = PB and thus
Patm + ρ oil g ( hoil + x ) = Patm + ρ Hg gh Hg
→ SG oil ρ w g ( hoil + x ) = SG Hg ρ w g ( 5 x )
Solving for x and substituting,
x=
2.72 (18 cm )
SG oil hoil
=
= 0.75 cm
5SG Hg − SG oil 5 × 13.6 − 2.72
Therefore, the maximum amount of oil that can be added into the left arm is
V oil, max = π (2d / 2) 2 (hoil + x ) = π (2 cm) 2 (18 + 0.75 cm) = 236 cm 3 = 0.236 L
Oil
SG=2.72
hoil = 18 cm
h = 4x
A
x
2d
B
d = 2 cm
Mercury
SG=13.6
Discussion
involved.
Note that the fluid levels in the two arms of a U-tube can be different when two different fluids are
3-81
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-129
Solution
The pressure buildup in a teapot may cause the water to overflow through the service tube. The maximum
cold-water height to avoid overflow under a specified gage pressure is to be determined.
Assumptions 1 Water is incompressible. 2 Thermal expansion and the amount of water in the service tube are negligible.
3 The cold water temperature is 20°C.
Properties
The density of water at 20°C is ρw = 998.0 kg/m3.
Analysis
From geometric considerations, the vertical distance between the bottom of the teapot and the tip of the
service tube is
htip = 4 + 12 cos 40° = 13.2 cm
This would be the maximum water height if there were no pressure build-up inside by the steam. The steam pressure inside
the teapot above the atmospheric pressure must be balanced by the water column inside the service tube,
Pv, gage = ρ w gΔh w
or,
Δh w =
Pv, gage
ρw g
=
⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
(998.0 kg/m )(9.81 m/s ) ⎜⎝
0.32 kPa
3
2
⎞⎛ 1 kN/m 2
⎟⎜
⎟⎜ 1 kPa
⎠⎝
⎞
⎟ = 0.033 m = 3.3 cm
⎟
⎠
Therefore, the water level inside the teapot must be 3.3 cm below the tip of the service tube. Then the maximum initial
water height inside the teapot to avoid overflow becomes
h w, max = h tip − Δh w = 13.2 − 3.3 = 9.9 cm
vapor
Pv
400
12 cm
hw
4 cm
Heat
Discussion
We can obtain the same result formally by starting with the vapor pressure in the teapot and moving along
the service tube by adding (as we go down) or subtracting (as we go up) the ρgh terms until we reach the atmosphere, and
setting the result equal to Patm:
Patm + Pv , gage − ρ w gh w = Patm
→
Pv , gage = ρ w gh w
3-82
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-130
Solution
The pressure buildup in a teapot may cause the water to overflow through the service tube. The maximum
cold-water height to avoid overflow under a specified gage pressure is to be determined by considering the effect of
thermal expansion.
Assumptions
1 The amount of water in the service tube is negligible. 3 The cold water temperature is 20°C.
Properties
The density of water is ρw = 998.0 kg/m3 at 20°C, and ρw = 957.9 kg/m3 at 100°C
Analysis
From geometric considerations, the vertical distance between the bottom of the teapot and the tip of the
service tube is
htip = 4 + 12 cos 40° = 13.2 cm
This would be the maximum water height if there were no pressure build-up inside by the steam. The steam pressure inside
the teapot above the atmospheric pressure must be balanced by the water column inside the service tube,
Pv, gage = ρ w gΔh w
or,
Δh w =
Pv, gage
ρw g
=
⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
(998.0 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
0.32 kPa
⎞⎛ 1 kN/m 2
⎟⎜
⎟⎜ 1 kPa
⎠⎝
⎞
⎟ = 0.033 m = 3.3 cm
⎟
⎠
Therefore, the water level inside the teapot must be 3.4 cm below the tip of the service tube. Then the height of hot water
inside the teapot to avoid overflow becomes
hw = htip − Δhw = 13.2 − 3.4 = 9.8 cm
The specific volume of water is 1/998 m3/kg at 20°C and 1/957.9 m3/kg at 100°C. Then the percent drop in the volume of
water as it cools from 100°C to 20°C is
Volume reduction =
v 100°C − v 20°C 1 / 957.9 − 1 / 998.0
= 0.040 or 4.0%
=
1 / 957.9
v 100°C
Volume is proportional to water height, and to allow for thermal
expansion, the volume of cold water should be 4% less.
Therefore, the maximum initial water height to avoid overflow
should be
hw, max = (1 − 0.040)h w = 0.96 × 9.8 cm = 9.4 cm
vapor
Pv
400
12 cm
hw
4 cm
Heat
Discussion
Note that the effect of thermal expansion can be quite significant.
3-83
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-131
Solution
The temperature of the atmosphere varies with altitude z as T = T0 − βz , while the gravitational
acceleration varies by g ( z ) = g 0 /(1 + z / 6,370,320) 2 . Relations for the variation of pressure in atmosphere are to be
obtained (a) by ignoring and (b) by considering the variation of g with altitude.
Assumptions
The air in the troposphere behaves as an ideal gas.
(a) Pressure change across a differential fluid layer of thickness dz in the vertical z direction is
dP = − ρgdz
P
P
From the ideal gas relation, the air density can be expressed as ρ =
. Then,
=
RT R (T0 − β z )
P
dP = −
gdz
R (T0 − βz )
Separating variables and integrating from z = 0 where P = P0 to z = z where P = P,
Analysis
z
gdz
dP
=−
P0 P
0 R (T0 − β z )
Performing the integrations.
∫
P
∫
T − βz
g
P
=
ln 0
P0 Rβ
T0
Rearranging, the desired relation for atmospheric pressure for the case of constant g becomes
ln
g
⎛ β z ⎞ βR
P = P0 ⎜⎜1 − ⎟⎟
⎝ T0 ⎠
(b) When the variation of g with altitude is considered, the procedure remains the same but the expressions become more
complicated,
g0
P
dz
R(T0 − βz ) (1 + z / 6,370,320) 2
Separating variables and integrating from z = 0 where P = P0 to z = z where P = P,
dP = −
∫
P
dP
=−
P
∫
z
g 0 dz
R (T0 − β z )(1 + z / 6,370,320) 2
Performing the integrations,
P0
ln P
P
P0
0
g
1 + kz
1
1
= 0
−
ln
2
Rβ (1 + kT0 / β )(1 + kz ) (1 + kT0 / β )
T0 − β z
z
0
where R = 287 J/kg⋅K = 287 m2/s2⋅K is the gas constant of air. After some manipulations, we obtain
⎡
⎛ 1
g0
1 + kz
1
⎜
P = P0 exp ⎢−
⎜ 1 + 1 / kz + 1 + kT / β ln 1 − βz / T
+
β
R
(
kT
)
0 ⎝
0
0
⎣⎢
⎞⎤
⎟⎥
⎟
⎠⎦⎥
where T0 = 288.15 K, β = 0.0065 K/m, g0 = 9.807 m/s2, k = 1/6,370,320 m-1, and z is the elevation in m..
Discussion
When performing the integration in part (b), the following expression from integral tables is used, together
with a transformation of variable x = T0 − β z ,
dx
a + bx
1
1
=
−
ln
x
x(a + bx ) 2 a (a + bx ) a 2
∫
Also, for z = 11,000 m, for example, the relations in (a) and (b) give 22.62 and 22.69 kPa, respectively.
3-84
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-132
Solution
The variation of pressure with density in a thick gas layer is given. A relation is to be obtained for pressure
as a function of elevation z.
Assumptions
The property relation P = Cρ n is valid over the entire region considered.
Analysis
The pressure change across a differential fluid layer of thickness dz in the vertical z direction is given as,
dP = − ρgdz
Also, the relation P = Cρ n can be expressed as C = P / ρ n = P0 / ρ 0n , and thus
ρ = ρ 0 ( P / P0 ) 1 / n
Substituting,
dP = − gρ 0 ( P / P0 ) 1 / n dz
Separating variables and integrating from z = 0 where P = P0 = Cρ 0n to z = z where P = P,
∫
P
P0
( P / P0 ) −1 / n dP = − ρ 0 g
z
∫ dz
0
Performing the integrations.
( P / P0 ) −1 / n +1
P0
− 1/ n + 1
P
= − ρ 0 gz
P0
→
⎛ P
⎜
⎜P
⎝ 0
⎞
⎟
⎟
⎠
( n −1) / n
−1 = −
n − 1 ρ 0 gz
n
P0
Solving for P,
⎛ n − 1 ρ 0 gz ⎞
⎟
P = P0 ⎜⎜1 −
n
P0 ⎟⎠
⎝
n /( n −1)
which is the desired relation.
Discussion
The final result could be expressed in various forms. The form given is very convenient for calculations as
it facilitates unit cancellations and reduces the chance of error.
3-85
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-133
Solution
A pressure transducer is used to measure pressure by generating analogue signals, and it is to be calibrated
by measuring both the pressure and the electric current simultaneously for various settings, and the results are to be
tabulated. A calibration curve in the form of P = aI + b is to be obtained, and the pressure corresponding to a signal of 10
mA is to be calculated.
Assumptions
Mercury is an incompressible liquid.
Properties
The specific gravity of mercury is given to be 13.56, and thus its density is 13,560 kg/m3.
Analysis
For a given differential height, the pressure can be calculated from
P = ρgΔh
For Δh = 28.0 mm = 0.0280 m, for example,
⎛
1 kN
P = 13.56(1000 kg/m 3 )(9.81 m/s 2 )(0.0280 m)⎜
⎜ 1000 kg ⋅ m/s 2
⎝
⎞⎛ 1 kPa ⎞
⎟⎜
= 3.72 kPa
⎟⎝ 1 kN/m 2 ⎟⎠
⎠
Repeating the calculations and tabulating, we have
Δh(mm)
P(kPa)
I (mA)
28.0
3.72
4.21
181.5
24.14
5.78
297.8
39.61
6.97
413.1
54.95
8.15
765.9
101.9
11.76
1027
136.6
14.43
1149
152.8
15.68
1362
181.2
17.86
1458
193.9
18.84
1536
204.3
19.64
A plot of P versus I is given below. It is clear that the pressure varies linearly with the current, and using EES, the best
curve fit is obtained to be
Multimeter
P = 13.00I - 51.00
(kPa) for 4.21 ≤ I ≤ 19.64 .
For I = 10 mA, for example, we would get P = 79.0 kPa.
Pressure
transducer
225
Valve
180
P, kPa
135
Pressurized
Air, P
90
Rigid container
Δh
45
0
4
6
8
10
12
14
16
18
Mercury
SG=13.5
6
20
I, mA
Discussion
Manometer
Note that the calibration relation is valid in the specified range of currents or pressures.
3-86
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-134
Solution
A system is equipped with two pressure gages and a manometer. For a given differential fluid height, the
pressure difference ΔP = P2 - P1 is to be determined.
Assumptions
1 All the liquids are incompressible. 2 The effect of air column on pressure is negligible.
Properties
The specific gravities are given tone 2.67 for the gage fluid and 0.87 for oil. We take the standard density
of water to be ρw = 1000 kg/m3.
Analysis
Starting with the pressure indicated by the pressure gage 2 and moving along the tube by adding (as we go
down) or subtracting (as we go up) the ρgh terms and ignoring the air spaces until we reach the pressure gage 1, and
setting the result equal to P1 give
P2 − ρ gage ghgage + ρ oil ghoil = P1
Rearranging,
P2 − P1 = ρ w g ( SG gage hgage − SG oil hoil )
Substituting,
⎛
1 kN
P2 − P1 = (1000 kg/m 3 )(9.81 m/s 2 )[2.67(0.08 m) − 0.87(0.65 m)]⎜⎜
2
⎝ 1000 kg ⋅ m/s
= −3.45 kPa
⎞⎛ 1 kPa ⎞
⎟⎜
⎟⎝ 1 kN/m 2 ⎟⎠
⎠
Therefore, the pressure reading of the left gage is 3.45 kPa lower than that of the right gage.
Air
Manometer
fluid, SG=2.67
Δh
Oil
SG=0.87
P2
P1
Discussion
The negative pressure difference indicates that the pressure differential across the oil level is greater than
the pressure differential corresponding to the differential height of the manometer fluid.
3-87
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-135
Solution
An oil pipeline and a rigid air tank are connected to each other by a manometer. The pressure in the
pipeline and the change in the level of manometer fluid due to a air temperature drop are to be determined.
Assumptions 1 All the liquids are incompressible. 2 The effect of air column on pressure is negligible. 3 The air volume
in the manometer is negligible compared with the volume of the tank.
Properties
The specific gravities are given to be 2.68 for oil and 13.6 for mercury. We take the standard density of
water to be ρw = 1000 kg/m3. The gas constant of air is 0.287 kPa⋅m3/kg⋅K.
Analysis
(a) Starting with the oil pipe and moving along the tube by adding (as we go down) or subtracting (as we
go up) the ρgh terms until we reach the air tank, and setting the result equal to Pair give
Poil + ρ oil ghoil + ρ Hg ghHg = Pair
The absolute pressure in the air tank is determined from the ideal-gas relation PV = mRT to be
mRT (15 kg)(0.287 kPa ⋅ m 3 /kg ⋅ K)(80 + 273)K
Pair =
=
= 1169 kPa
V
1.3 m 3
Then the absolute pressure in the oil pipe becomes
Poil = Pair − ρoil ghoil − ρ Hg ghHg
⎛
⎞ ⎛ 1 kPa ⎞
1 kN
= 1169 kPa − (1000 kg/m3 ) (9.81 m/s 2 ) ⎣⎡ 2.68(0.75 m) + 13.6 ( 0.20 m ) ⎦⎤ ⎜
2 ⎟⎜
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠ ⎝ 1 kN/m ⎠
= 1123 kPa ≅ 1120 kPa
(b) The pressure in the air tank when the temperature drops to 20°C becomes
mRT (15 kg)(0.287 kPa ⋅ m 3 /kg ⋅ K)(20 + 273)K
Pair =
=
= 970 kPa
V
1.3 m 3
When the mercury level in the left arm drops a distance x, the rise in the mercury level in the right arm y becomes
V left = V right →
π (3d ) 2 x = πd 2 y
→
y = 9 x and y vert = 9x sin 50°
and the mercury fluid height will change by x + 9x sin 50° or 7.894x. Then,
Poil + ρ oil g ( hoil + x ) + ρ Hg g (hHg − 7.894 x ) = Pair → SG oil ( hoil + x ) + SG Hg ( hHg − 7.894 x ) =
Pair − Poil
ρw g
Substituting,
⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
(1000 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
which yields x = 0.194 m = 19.4 cm . Therefore, the oil-mercury
interface will drop 19.4 cm as a result of the temperature drop of air.
2.68(0.75 + x) + 13.6(0.20 − 7.894 x) =
(970 − 1123) kPa
⎞⎛ 1 kN/m 2
⎟⎜
⎟⎜ 1 kPa
⎠⎝
⎞
⎟
⎟
⎠
B
Air, 80 0C
A, Oil
SG=2.68
hoil = 75
hHg = Δh = 20 cm
3d
d = 4 mm
500
Discussion
Mercury
SG=13.6
Note that the pressure in constant-volume gas chambers is very sensitive to temperature changes.
3-88
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-136
Solution
The density of a wood log is to be measured by tying lead weights to it until both the log and the weights
are completely submerged, and then weighing them separately in air. The average density of a given log is to be determined
by this approach.
Properties
The density of lead weights is given to be 11,300 kg/m3. We take the density of water to be 1000 kg/m3.
Analysis
The weight of a body is equal to the buoyant force when the body is floating in a fluid while being
completely submerged in it (a consequence of vertical force balance from static equilibrium). In this case the average
density of the body must be equal to the density of the fluid since
W = FB
ρ body gV = ρ fluid gV
→
→
ρ body = ρ fluid
Lead, 34 kg
Therefore,
ρ ave =
m total mlead + mlog
=
= ρ water
V total
V lead +V log
→
V log = V lead +
mlead + mlog
Log, 1540 N
ρ water
FB
where
Water
V lead =
mlog =
mlead
ρ lead
Wlog
g
=
=
34 kg
11,300 kg/m
3
= 3.01× 10 −3 m 3
1540 N ⎛ 1 kg ⋅ m/s 2
⎜
1N
9.81 m/s 2 ⎜⎝
⎞
⎟ = 157.0 kg
⎟
⎠
Substituting, the volume and density of the log are determined to be
Vlog = Vlead +
ρ log =
m log
Vlog
=
mlead + mlog
ρ water
157 kg
0.194 m
3
= 3.01×10 −3 m 3 +
(34 + 157) kg
1000 kg/m 3
= 0.194 m 3
= 809 kg/m 3
Discussion
Note that the log must be completely submerged for this analysis to be valid. Ideally, the lead weights must
also be completely submerged, but this is not very critical because of the small volume of the lead weights.
3-89
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-137 [Also solved using EES on enclosed DVD]
Solution
A rectangular gate that leans against the floor with an angle of 45° with the horizontal is to be opened from
its lower edge by applying a normal force at its center. The minimum force F required to open the water gate is to be
determined.
Assumptions 1 Atmospheric pressure acts on both sides of the gate, and thus it can be ignored in calculations for
convenience. 2 Friction at the hinge is negligible.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
The length of the gate and the distance of the upper edge of the gate (point B) from the free surface in the
plane of the gate are
3m
= 4.243 m
sin 45°
b=
and
s=
0. 5 m
= 0.7071 m
sin 45°
The average pressure on a surface is the pressure at the centroid (midpoint) of
the surface, and multiplying it by the plate area gives the resultant hydrostatic
on the surface,
FR
0.5 m
B
FR = Pavg A = ρ ghC A
⎛
⎞
1 kN
= (1000 kg/m )( 9.81 m/s ) ( 2 m ) ( 5 × 4.243 m ) ⎜
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠
= 416 kN
3
2
3m
2
A
45°
F
The distance of the pressure center from the free surface of water along the plane of
the gate is
yP = s +
4.243
4.243 2
b
b2
+
= 0.7071 +
+
= 3.359 m
2
12(0.7071 + 4.243 / 2)
2 12( s + b / 2)
The distance of the pressure center from the hinge at point B is
L P = y P − s = 3.359 − 0.7071 = 2.652 m
Taking the moment about point B and setting it equal to zero gives
∑M
B
=0
→
FR L P = Fb / 2
Solving for F and substituting, the required force is determined to be
F=
2 FR L P 2( 416 kN)(2.652 m)
=
= 520 kN
4.243 m
b
Discussion
The applied force is inversely proportional to the distance of the point of application from the hinge, and
the required force can be reduced by applying the force at a lower point on the gate.
3-90
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-138
Solution
A rectangular gate that leans against the floor with an angle of 45° with the horizontal is to be opened from
its lower edge by applying a normal force at its center. The minimum force F required to open the water gate is to be
determined.
Assumptions 1 Atmospheric pressure acts on both sides of the gate, and thus it can be ignored in calculations for
convenience. 2 Friction at the hinge is negligible.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
The length of the gate and the distance of the upper edge of the gate
(point B) from the free surface in the plane of the gate are
3m
= 4.243 m
sin 45°
b=
and
s=
1.2 m
= 1.697 m
sin 45°
FR
1.2 m
The average pressure on a surface is the pressure at the centroid (midpoint) of the
surface, and multiplying it by the plate area gives the resultant hydrostatic on the
surface,
B
3m
FR = Pavg A = ρ ghC A
⎛
⎞
1 kN
= (1000 kg/m3 )( 9.81 m/s 2 ) ( 2.7 m ) ( 5 × 4.243 m 2 ) ⎜
2 ⎟
1000
kg
m/s
⋅
⎝
⎠
= 562 kN
A
45°
F
The distance of the pressure center from the free surface of water along the plane of
the gate is
yP = s +
b
b2
4.243
4.243 2
+
= 1.697 +
+
= 4.211 m
2
12(1.697 + 4.243 / 2)
2 12( s + b / 2)
The distance of the pressure center from the hinge at point B is
L P = y P − s = 4.211 − 1.697 = 2.514 m
Taking the moment about point B and setting it equal to zero gives
∑M
B
=0
→
FR L P = Fb / 2
Solving for F and substituting, the required force is determined to be
F=
2 FR L P 2(562 N)(2.514 m)
=
= 666 kN
4.243 m
b
Discussion
The applied force is inversely proportional to the distance of the point of application from the hinge, and
the required force can be reduced by applying the force at a lower point on the gate.
3-91
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-139
Solution
A rectangular gate hinged about a horizontal axis along its upper edge is restrained by a fixed ridge at point
B. The force exerted to the plate by the ridge is to be determined.
Assumptions
convenience.
Atmospheric pressure acts on both sides of the gate, and thus it can be ignored in calculations for
Properties
We take the density of water to be 1000 kg/m3 throughout.
Analysis
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and multiplying it by the plate area gives the resultant
hydrostatic force on the gate,
2m
FR = Pavg A = ρ ghC A
A
⎛
⎞
1 kN
= (1000 kg/m3 )( 9.81 m/s 2 ) ( 3.5 m ) ( 3 × 6 m 2 ) ⎜
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠
= 618 kN
yp
3m
The vertical distance of the pressure center from the free surface of water is
FR
3
32
b
b2
= 2+ +
= 3.71 m
yP = s + +
2 12( s + b / 2)
2 12(2 + 3 / 2)
Discussion
You can calculate the force at point B required to hold back the gate by setting the net moment around
hinge point A to zero.
3-140
Solution
A rectangular gate hinged about a horizontal axis along its upper edge is restrained by a fixed ridge at point
B. The force exerted to the plate by the ridge is to be determined.
Assumptions
convenience.
Atmospheric pressure acts on both sides of the gate, and thus it can be ignored in calculations for
Properties
We take the density of water to be 1000 kg/m3 throughout.
Analysis
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and multiplying it by the wetted plate area gives the resultant
hydrostatic force on the gate,
A
FR = Pave A = ρghC A
⎛
1 kN
= (1000 kg/m 3 )(9.81 m/s 2 )(1 m)[2 × 6 m 2 ]⎜⎜
2
⎝ 1000 kg ⋅ m/s
= 118 kN
⎞
⎟
⎟
⎠
The vertical distance of the pressure center from the free surface of water is
yP =
3m
yP
FR
h=2m
2h 2(2 m )
=
= 1.33 m
3
3
Discussion
Compared to the previous problem (with higher water depth), the force is much smaller, as expected. Also,
the center of pressure on the gate is much lower (closer to the ground) for the case with the lower water depth.
3-92
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-141E
Solution
A semicircular tunnel is to be built under a lake. The total hydrostatic force acting on the roof of the tunnel
is to be determined.
Fy
Assumptions Atmospheric pressure acts on both sides of the
tunnel, and thus it can be ignored in calculations for convenience.
Properties
throughout.
We take the density of water to be 62.4 lbm/ft3
Analysis
We consider the free body diagram of the liquid
block enclosed by the circular surface of the tunnel and its vertical
(on both sides) and horizontal projections. The hydrostatic forces
acting on the vertical and horizontal plane surfaces as well as the
weight of the liquid block are determined as follows:
Fx
Fx
W
R = 15 ft
Horizontal force on vertical surface (each side):
FH = Fx = Pavg A = ρ ghC A = ρ g ( s + R / 2 ) A
1 lbf
⎛
⎞
= ( 62.4 lbm/ft 3 )( 32.2 ft/s 2 ) (135 + 15 / 2 ft )(15 ft × 800 ft ) ⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
= 1.067 × 108 lbf (on each side of the tunnel)
Vertical force on horizontal surface (downward):
Fy = Pavg A = ρ ghC A = ρ ghtop A
1 lbf
⎛
⎞
= ( 62.4 lbm/ft 3 )( 32.2 ft/s 2 ) (135 ft )( 30 ft × 800 ft ) ⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
= 2.022 × 108 lbf
Weight of fluid block on each side within the control volume (downward):
W = mg = ρgV = ρg ( R 2 − πR 2 / 4 )(2000 ft)
1 lbf
⎞
⎛
= (62.4 lbm/ft 3 )(32.2 ft/s 2 )(15 ft) 2 (1 - π/4)(800 ft)⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
= 2.410 × 10 6 lbf (on each side)
Therefore, the net downward vertical force is
FV = Fy + 2W = 2.022 × 108 + 2 × 0.02410 × 106 = 2.07 × 108 lbf
This is also the net force acting on the tunnel since the horizontal forces acting on the right and left side of the tunnel
cancel each other since they are equal and opposite.
Discussion
The weight of the two water bocks on the sides represents only about 2.4% of the total vertical force on the
tunnel. Therefore, to obtain a reasonable first approximation for deep tunnels, these volumes can be neglected, yielding FV
= 2.02 × 108 lbf. A more conservative approximation would be to estimate the force on the bottom of the lake if the tunnel
were not there. This yields FV = 2.25 × 108 lbf. The actual force is between these two estimates, as expected.
3-93
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-142
Solution
A hemispherical dome on a level surface filled with water is to be lifted by attaching a long tube to the top
and filling it with water. The required height of water in the tube to lift the dome is to be determined.
Assumptions 1 Atmospheric pressure acts on both sides of the dome, and thus it can be ignored in calculations for
convenience. 2 The weight of the tube and the water in it is negligible.
We take the density of water to be 1000 kg/m3 throughout.
Properties
Analysis
We take the dome and the water in it as the system. When the dome is about to rise, the reaction force
between the dome and the ground becomes zero. Then the free body diagram of this system involves the weights of the
dome and the water, balanced by the hydrostatic pressure force from below. Setting these forces equal to each other gives
∑F
y
= 0:
FV = Wdome + W water
ρg (h + R )πR 2 = m dome g + m water g
Solving for h gives
h=
h
m dome + m water
ρπR 2
−R =
m dome + ρ[4πR 3 / 6]
ρπR 2
−R
R=3m
Substituting,
h=
(50,000 kg) + 4π (1000 kg/m 3 )(3 m) 3 / 6
(1000 kg/m 3 )π (3 m) 2
− (3 m) = 0.77 m
FV
Therefore, this dome can be lifted by attaching a tube which is 77 cm long.
Discussion
Note that the water pressure in the dome can be changed greatly
by a small amount of water in the vertical tube.
3-94
W
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-143
Solution
The water in a reservoir is restrained by a triangular wall. The total force (hydrostatic + atmospheric) acting
on the inner surface of the wall and the horizontal component of this force are to be determined.
Assumptions 1 Atmospheric pressure acts on both sides of the gate, and thus it can be ignored in calculations for
convenience. 2 Friction at the hinge is negligible.
Properties
throughout.
We take the density of water to be 1000 kg/m3
Analysis The length of the wall surface underwater is
b=
yp
25 m
= 28.87 m
sin 60°
FR
h = 25 m
The average pressure on a surface is the pressure at the centroid
(midpoint) of the surface, and multiplying it by the plate area gives
the resultant hydrostatic force on the surface,
FR = Pavg A = ( Patm + ρ ghC ) A
⎛ 1N
⎞
= ⎣⎡100 , 000 N/m 2 + (1000 kg/m3 )( 9.81 m/s 2 ) (12.5 m ) ⎦⎤ (150 × 28.87 m 2 ) ⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
8
= 9.64 × 10 N
Noting that
⎛ 1 kg ⋅ m/s 2
P0
100,000 N/m 2
⎜
=
ρg sin 60° (1000 kg/m 3 )(9.81 m/s 2 ) sin 60° ⎜⎝ 1 N
⎞
⎟ = 11.77 m
⎟
⎠
the distance of the pressure center from the free surface of water along the wall surface is
yp = s+
b
+
2
b2
P0
⎛
b
12⎜⎜ s + +
ρ
g
2
sin θ
⎝
⎞
⎟⎟
⎠
= 0+
28.87 m
+
2
(28.87 m) 2
= 17.1 m
28.87 m
⎞
⎛
+ 11.77 m ⎟
12⎜ 0 +
2
⎠
⎝
The magnitude of the horizontal component of the hydrostatic force is simply FRsin θ,
FH = FR sin θ = (9.64 × 10 8 N)sin60° = 8.35 × 10 8 N
Discussion
walls.
Atmospheric pressure is usually ignored in the analysis for convenience since it acts on both sides of the
3-95
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-144
Solution
A U-tube that contains water in its right arm and another liquid in its left arm is rotated about an axis closer
to the left arm. For a known rotation rate at which the liquid levels in both arms are the same, the density of the fluid in the
left arm is to be determined.
Assumptions 1 Both the fluid and the water are incompressible fluids. 2 The
two fluids meet at the axis of rotation, and thus there is only water to the right of
the axis of rotation.
We take the density of water to be 1000 kg/m3.
Properties
1
•
Water
Fluid
•
1*
Analysis
The pressure difference between two points 1 and 2 in an
incompressible fluid rotating in rigid body motion (the same fluid) is given by
P2 − P1 =
ρω 2
2
h = 10 cm
(r22
− r12 ) − ρg ( z 2
− z1 )
z
where
•
2
1 min ⎞
ω = 2πn = 2π (30 rev/min)⎛⎜
⎟ = 3.14 rad/s
⎝ 60 s ⎠
(for both arms of the U-tube).
R1 = 5 cm
r
R2 = 15 cm
The pressure at point 2 is the same for both fluids, so are the pressures at points 1 and 1* (P1 = P1* = Patm). Therefore,
P2 − P1 is the same for both fluids. Noting that z 2 − z1 = −h for both fluids and expressing P2 − P1 for each fluid,
Water: P2 − P1 * =
Fluid: P2 − P1 =
ρ wω 2
2
ρ fω2
2
(0 − R 22 ) − ρ w g (−h) = ρ w (−ω 2 R 22 / 2 + gh )
(0 − R12 ) − ρ f g (−h ) = ρ f (−ω 2 R12 / 2 + gh )
Setting them equal to each other and solving for ρf gives
− ( 3.14 rad/s ) ( 0.15 m ) + ( 9.81 m/s 2 ) ( 0.10 m )
−ω 2 R22 / 2 + gh
=
ρ
(1000 kg/m3 ) = 794 kg/m3
w
2
2
2
−ω 2 R12 / 2 + gh
− ( 3.14 rad/s ) ( 0.05 m ) + ( 9.81 m/s ) ( 0.10 m )
2
ρf =
Discussion
2
Note that this device can be used to determine relative densities, though it wouldn’t be very practical.
3-96
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-145
Solution
A vertical cylindrical tank is completely filled with gasoline, and the tank is rotated about its vertical axis at
a specified rate while being accelerated upward. The pressures difference between the centers of the bottom and top
surfaces, and the pressures difference between the center and the edge of the bottom surface are to be determined.
Assumptions 1 The increase in the rotational speed is very slow so
that the liquid in the container always acts as a rigid body. 2 Gasoline
is an incompressible substance.
The density of the gasoline is given to be 740 kg/m3.
Properties
Analysis
The pressure difference between two points 1 and 2 in
an incompressible fluid rotating in rigid body motion is given by
5 m/s2
ρω 2
(r22 − r12 ) − ρg ( z 2 − z1 ) . The effect of linear
2
acceleration in the vertical direction is accounted for by replacing g by
g + a z . Then,
P2 − P1 =
P2 − P1 =
ρω 2
2
D=1m
h=2m
z
(r22 − r12 ) − ρ ( g + a z )( z 2 − z1 )
0
r
where R = 0.50 m is the radius, and
ω = 2πn = 2π (90 rev/min)⎛⎜
1 min ⎞
⎟ = 9.425 rad/s
⎝ 60 s ⎠
(a) Taking points 1 and 2 to be the centers of the bottom and top surfaces, respectively, we have r1 = r2 = 0 and
z 2 − z1 = h = 3 m . Then,
Pcenter, top − Pcenter, bottom = 0 − ρ ( g + a z )( z 2 − z1 ) = − ρ ( g + a z )h
⎛
1 kN
= −(740 kg/m 3 )(9.81 m/s 2 + 5)(2 m)⎜⎜
1000
kg ⋅ m/s 2
⎝
⎞
⎟ = 21.8 kN/m 2 = 21.9 kPa
⎟
⎠
(b) Taking points 1 and 2 to be the center and edge of the bottom surface, respectively, we have r1 = 0 , r2 = R , and
z 2 = z1 = 0 . Then,
Pedge, bottom − Pcenter, bottom =
ρω 2
( R 22 − 0) − 0 =
ρω 2 R 2
2
2
(740 kg/m 3 )(9.425 rad/s) 2 (0.50 m) 2
=
2
⎛
1 kN
⎜
⎜ 1000 kg ⋅ m/s 2
⎝
⎞
⎟ = 8.22 kN/m 2 = 8.22 kPa
⎟
⎠
Discussion
Note that the rotation of the tank does not affect the pressure difference along the axis of the tank.
Likewise, the vertical acceleration does not affect the pressure difference between the edge and the center of the bottom
surface (or any other horizontal plane).
3-97
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-146
Solution
A rectangular water tank open to the atmosphere is accelerated to the right on a level surface at a specified
rate. The maximum pressure in the tank above the atmospheric level is to be determined.
Vent
1.5 m
θ
•
ax = 2 m/s2
Water
tank
h0 =2.5 m
•
2
1
L =5 m
Assumptions 1 The road is horizontal during acceleration so that acceleration has no vertical component (az = 0). 2
Effects of splashing, breaking and driving over bumps are assumed to be secondary, and are not considered. 3 The vent is
never blocked, and thus the minimum pressure is the atmospheric pressure.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
We take the x-axis to be the direction of motion, the z-axis to be the upward vertical direction. The tangent
of the angle the free surface makes with the horizontal is
ax
2
=
= 0.2039 (and thus θ = 11.5°)
g + a z 9.81 + 0
The maximum vertical rise of the free surface occurs at the back of the tank, and the vertical midsection experiences no rise
or drop during acceleration. Then the maximum vertical rise at the back of the tank relative to the neutral midplane is
tan θ =
Δz max = ( L / 2) tan θ = [(5 m)/2] × 0.2039 = 0.510 m
which is less than 1.5 m high air space. Therefore, water never reaches the ceiling, and the maximum water height and the
corresponding maximum pressure are
hmax = h0 + Δz max = 2.50 + 0.510 = 3.01 m
⎛
1 kN
Pmax = P1 = ρghmax = (1000 kg/m 3 )(9.81 m/s 2 )(3.01 m)⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟ = 29.5 kN/m 2 = 29.5 kPa
⎟
⎠
Discussion
It can be shown that the gage pressure at the bottom of the tank varies from 29.5 kPa at the back of the tank
to 24.5 kPa at the midsection and 19.5 kPa at the front of the tank.
3-98
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-147
Solution
The previous problem is reconsidered. The effect of acceleration on the slope of the free surface of water in
the tank as the acceleration varies from 0 to 5 m/s2 in increments of 0.5 m/s2 is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
g=9.81 "m/s2"
rho=1000 "kg/m3"
L=5 "m"
h0=2.5 "m"
a_z=0
tan(theta)=a_x/(g+a_z)
h_max=h0+(L/2)*tan(theta)
P_max=rho*g*h_max/1000 "kPa"
Acceleration
ax, m/s2
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Free surface
angle, θ°
0.0
2.9
5.8
8.7
11.5
14.3
17.0
19.6
22.2
24.6
27.0
Maximum height
hmax, m
2.50
2.63
2.75
2.88
3.01
3.14
3.26
3.39
3.52
3.65
3.77
Maximum pressure
Pmax, kPa
24.5
25.8
27.0
28.3
29.5
30.8
32.0
33.3
34.5
35.8
37.0
30
25
θ°
20
15
10
5
0
0
1
2
3
ax , m/s
Discussion
2
4
5
Note that water never reaches the ceiling, and a full free surface is formed in the tank.
3-99
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-148
Solution
An elastic air balloon submerged in water is attached to the base of the tank. The change in the tension
force of the cable is to be determined when the tank pressure is increased and the balloon diameter is decreased in
accordance with the relation P = CD-2.
Assumptions 1 Atmospheric pressure acts on all surfaces, and thus it can be
ignored in calculations for convenience. 2 Water is an incompressible fluid. 3
The weight of the balloon and the air in it is negligible.
Properties
P1=100 kPa
We take the density of water to be 1000 kg/m3.
D1=30 cm
The tension force on the cable holding the balloon is determined
Analysis
from a force balance on the balloon to be
Water
Fcable = FB − Wballoon ≅ FB
The buoyancy force acting on the balloon initially is
⎞
1N
⎟ = 138.7 N
⎜
2 ⎟
⎜
6
6
⎝ 1 kg ⋅ m/s ⎠
The variation of pressure with diameter is given as P = CD −2 , which is equivalent to D = C / P . Then the final diameter
of the ball becomes
C / P2
P
P1
D2
0.1 MPa
=
=
→ D 2 = D1 1 = (0.30 m)
= 0.075 m
P2
P2
1.6 MPa
D1
C / P1
FB ,1 = ρ w gV balloon,1 = ρ w g
πD13
= (1000 kg/m 3 )(9.81 m/s 2 )
π (0.30 m) 3 ⎛
The buoyancy force acting on the balloon in this case is
FB , 2 = ρ w gV balloon, 2 = ρ w g
πD 23
6
= (1000 kg/m 3 )(9.81 m/s 2 )
⎞
⎟ = 2.2 N
⎜ 1 kg ⋅ m/s 2 ⎟
⎠
⎝
π (0.075 m) 3 ⎛⎜
6
1N
Then the percent change in the cable for becomes
Change% =
Fcable,1 − Fcable,2
Fcable,1
* 100 =
FB,1 − FB,2
FB,1
* 100 =
138.7 − 2.2
* 100 = 98.4% .
138.7
Therefore, increasing the tank pressure in this case results in 98.4% reduction in cable tension.
Discussion
We can obtain a relation for the change in cable tension as follows:
Change% =
FB ,1 − FB ,2
FB ,1
* 100 =
ρ w gV balloon,1 − ρ w gV balloon,2
ρ w gV balloon,1
3 ⎞
⎛ ⎛
⎛ V balloon,2 ⎞
⎛
⎟ = 100⎜1 − D 2 ⎟ = 100⎜1 − ⎜ P1
= 100⎜1 −
⎜ D3 ⎟
⎜ V balloon,1 ⎟
⎜ ⎜⎝ P2
1 ⎠
⎝
⎠
⎝
⎝
⎞
⎟⎟
⎠
3/ 2
⎞
⎟
⎟
⎠
3-100
* 100
.
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-149
Solution
The previous problem is reconsidered. The effect of the air pressure above the water on the cable force as
the pressure varies from 0.1 MPa to 10 MPa is to be investigated.
The EES Equations window is printed below, followed by the tabulated and plotted results.
Analysis
P1=0.1 "MPa"
Change=100*(1-(P1/P2)^1.5)
100
%Change in
cable tension
0.0
64.6
80.8
87.5
93.2
95.6
96.8
98.9
99.4
99.6
99.7
99.8
99.8
99.9
99.9
99.9
80
Change in FB, %
Tank pressure
P2, MPa
0.1
0.2
0.3
0.4
0.6
0.8
1
2
3
4
5
6
7
8
9
10
60
40
20
0
0
2
4
6
8
10
P2, MPa
Discussion
The change in cable tension is at first very rapid, but levels off as the balloon shrinks to nearly zero
diameter at high pressure.
3-150
Solution
An iceberg floating in seawater is considered. The volume fraction of the iceberg submerged in seawater is
to be determined, and the reason for their turnover is to be explained.
Assumptions
1 The buoyancy force in air is negligible. 2 The density of iceberg and seawater are uniform.
Properties
The densities of iceberg and seawater are given to be 917 kg/m3 and 1042 kg/m3, respectively.
Analysis
(a) The weight of a body floating in a fluid is equal to the buoyant force acting on it (a consequence of
vertical force balance from static equilibrium). Therefore,
W = FB
Iceberg
ρ body gV total = ρ fluid gV submerged
Sea
V submerged
V total
=
ρ body
ρ fluid
=
ρ iceberg
ρ seawater
=
917
= 0.880 or 88%
1042
W
Therefore, 88% of the volume of the iceberg is submerged in this case.
(b) Heat transfer to the iceberg due to the temperature difference between the
seawater and an iceberg causes uneven melting of the irregularly shaped iceberg.
The resulting shift in the center of mass causes the iceberg to turn over.
Discussion
FB
The submerged fraction depends on the density of seawater, and this fraction can differ in different seas.
3-101
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
3-151
Solution
A cylindrical container equipped with a manometer is inverted and pressed into water. The differential
height of the manometer and the force needed to hold the container in place are to be determined.
F
h
Manometer fluid
SG=2.1
Air
D = 30 cm
20 cm
B
A
•
Water
•
Assumptions 1 Atmospheric pressure acts on all surfaces, and thus it can be ignored in calculations for convenience. 2
The variation of air pressure inside cylinder is negligible.
Properties
We take the density of water to be 1000 kg/m3. The density of the manometer fluid is
ρ mano = SG × ρ w = 2.1(1000 kg/m3 ) = 2100 kg/m3
Analysis
The pressures at point A and B must be the same since they are on the same horizontal line in the same
fluid. Then the gage pressure in the cylinder becomes
⎛ 1N
⎞
= (1000 kg/m3 )(9.81 m/s 2 )(0.20 m) ⎜
= 1962 N/m 2 = 1962 Pa
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
The manometer also indicates the gage pressure in the cylinder. Therefore,
Pair, gage = ρ w ghw
Pair, gage = ( ρ gh )mano → h =
Pair, gage
ρ mano g
=
⎛ 1 kg ⋅ m/s 2
1962 N/m 2
3
2 ⎜
(2100 kg/m )(9.81 m/s ) ⎝ 1 kN/m 2
⎞
⎟ = 0.0950 m = 9.50 cm
⎠
A force balance on the cylinder in the vertical direction yields
F + W = Pair, gage Ac
Solving for F and substituting,
F = Pair, gage
π D2
4
− W = (1962 N/m
2
)
π ( 0.30 m )
4
2
− 79 N = 59.7 N
Discussion
We could also solve this problem by considering the atmospheric pressure, but we would obtain the same
result since atmospheric pressure would cancel out.
3-102
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 3 Pressure and Fluid Statics
Design and Essay Problems
3-152
Solution
We are to discuss the design of shoes that enable people to walk on water.
Discussion
Students’ discussions should be unique and will differ from each other.
3-153
Solution
We are to discuss how to measure the volume of a rock without using any volume measurement devices.
Analysis
The volume of a rock can be determined without using any volume measurement devices as follows: We
weigh the rock in the air and then in the water. The difference between the two weights is due to the buoyancy force, which
is equal to FB = ρ water gV body . Solving this relation for Vbody gives the volume of the rock.
Discussion
techniques.
Since this is an open-ended design problem, students may come up with different, but equally valid
KJ
3-103
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications
by Çengel & Cimbala
CHAPTER 4
FLUID KINEMATICS
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of The McGraw-Hill Companies, Inc.
(“McGraw-Hill”) and protected by copyright and other state and federal laws. By
opening and using this Manual the user agrees to the following restrictions, and if the
recipient does not agree to these restrictions, the Manual should be promptly returned
unopened to McGraw-Hill: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated
textbook. No other use or distribution of this Manual is permitted. This Manual
may not be sold and may not be distributed to or used by any student or other
third party. No part of this Manual may be reproduced, displayed or distributed
in any form or by any means, electronic or otherwise, without the prior written
permission of McGraw-Hill.
4-1
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
Introductory Problems
4-1C
Solution
We are to define and explain kinematics and fluid kinematics.
Analysis
Kinematics means the study of motion. Fluid kinematics is the study of how fluids flow and how to
describe fluid motion. Fluid kinematics deals with describing the motion of fluids without considering (or even
understanding) the forces and moments that cause the motion.
Discussion
Fluid kinematics deals with such things as describing how a fluid particle translates, distorts, and rotates,
and how to visualize flow fields.
4-2
Solution
We are to write an equation for centerline speed through a nozzle, given that the flow speed increases
parabolically.
Assumptions
1 The flow is steady. 2 The flow is axisymmetric. 3 The water is incompressible.
Analysis
A general equation for a parabola in the x direction is
u = a + b ( x − c)
General parabolic equation:
2
(1)
We have two boundary conditions, namely at x = 0, u = uentrance and at x = L, u = uexit. By inspection, Eq. 1 is satisfied by
setting c = 0, a = uentrance and b = (uexit - uentrance)/L2. Thus, Eq. 1 becomes
Parabolic speed:
u = uentrance +
( uexit − uentrance )
L2
x2
(2)
Discussion
You can verify Eq. 2 by plugging in x = 0 and x = L.
4-3
Solution
location.
For a given velocity field we are to find out if there is a stagnation point. If so, we are to calculate its
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The velocity field is
G
G
G
V = ( u , v ) = ( 0.5 + 1.2 x ) i + ( −2.0 − 1.2 y ) j
(1)
At a stagnation point, both u and v must equal zero. At any point (x,y) in the flow field, the velocity components u and v are
obtained from Eq. 1,
Velocity components:
u = 0.5 + 1.2 x
v = −2.0 − 1.2 y
(2)
x = −0.4167
y = −1.667
(3)
Setting these to zero yields
Stagnation point:
0 = 0.5 + 1.2 x
0 = −2.0 − 1.2 y
So, yes there is a stagnation point; its location is x = -0.417, y = -1.67 (to 3 digits).
Discussion
If the flow were three-dimensional, we would have to set w = 0 as well to determine the location of the
stagnation point. In some flow fields there is more than one stagnation point.
4-2
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-4
Solution
location.
For a given velocity field we are to find out if there is a stagnation point. If so, we are to calculate its
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The velocity field is
G
G
2 G
V = ( u, v ) = a 2 − ( b − cx ) i + −2cby + 2c 2 xy j
(
) (
)
(1)
At a stagnation point, both u and v must equal zero. At any point (x,y) in the flow field, the velocity components u and v are
obtained from Eq. 1,
Velocity components:
u = a 2 − ( b − cx )
2
v = −2cby + 2c 2 xy
(2)
b−a
c
y=0
(3)
Setting these to zero and solving simultaneously yields
Stagnation point:
0 = a 2 − ( b − cx )
2
x=
v = −2cby + 2c xy
2
So, yes there is a stagnation point; its location is x = (b – a)/c, y = 0.
Discussion
If the flow were three-dimensional, we would have to set w = 0 as well to determine the location of the
stagnation point. In some flow fields there is more than one stagnation point.
Lagrangian and Eulerian Descriptions
4-5C
Solution
We are to define the Lagrangian description of fluid motion.
Analysis
In the Lagrangian description of fluid motion, individual fluid particles (fluid elements composed of a
fixed, identifiable mass of fluid) are followed.
Discussion
The Lagrangian method of studying fluid motion is similar to that of studying billiard balls and other solid
objects in physics.
4-6C
Solution
We are to compare the Lagrangian method to the study of systems and control volumes and determine to
which of these it is most similar.
Analysis
The Lagrangian method is more similar to system analysis (i.e., closed system analysis). In both cases,
we follow a mass of fixed identity as it moves in a flow. In a control volume analysis, on the other hand, mass moves into
and out of the control volume, and we don’t follow any particular chunk of fluid. Instead we analyze whatever fluid
happens to be inside the control volume at the time.
Discussion
to a point.
In fact, the Lagrangian analysis is the same as a system analysis in the limit as the size of the system shrinks
4-3
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-7C
Solution
description.
We are to define the Eulerian description of fluid motion, and explain how it differs from the Lagrangian
Analysis
In the Eulerian description of fluid motion, we are concerned with field variables, such as velocity,
pressure, temperature, etc., as functions of space and time within a flow domain or control volume. In contrast to the
Lagrangian method, fluid flows into and out of the Eulerian flow domain, and we do not keep track of the motion of
particular identifiable fluid particles.
Discussion
The Eulerian method of studying fluid motion is not as “natural” as the Lagrangian method since the
fundamental conservation laws apply to moving particles, not to fields.
4-8C
Solution
We are to determine whether a measurement is Lagrangian or Eulerian.
Analysis
Since the probe is fixed in space and the fluid flows around it, we are not following individual fluid
particles as they move. Instead, we are measuring a field variable at a particular location in space. Thus this is an Eulerian
measurement.
Discussion
If a neutrally buoyant probe were to move with the flow, its results would be Lagrangian measurements –
following fluid particles.
4-9C
Solution
We are to determine whether a measurement is Lagrangian or Eulerian.
Analysis
Since the probe moves with the flow and is neutrally buoyant, we are following individual fluid particles as
they move through the pump. Thus this is a Lagrangian measurement.
Discussion
If the probe were instead fixed at one location in the flow, its results would be Eulerian measurements.
4-10C
Solution
We are to determine whether a measurement is Lagrangian or Eulerian.
Analysis
Since the weather balloon moves with the air and is neutrally buoyant, we are following individual “fluid
particles” as they move through the atmosphere. Thus this is a Lagrangian measurement. Note that in this case the “fluid
particle” is huge, and can follow gross features of the flow – the balloon obviously cannot follow small scale turbulent
fluctuations in the atmosphere.
Discussion
When weather monitoring instruments are mounted on the roof of a building, the results are Eulerian
measurements.
4-11C
Solution
We are to determine whether a measurement is Lagrangian or Eulerian.
Analysis
Relative to the airplane, the probe is fixed and the air flows around it. We are not following individual fluid
particles as they move. Instead, we are measuring a field variable at a particular location in space relative to the moving
airplane. Thus this is an Eulerian measurement.
Discussion
The airplane is moving, but it is not moving with the flow.
4-4
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-12C
Solution
We are to compare the Eulerian method to the study of systems and control volumes and determine to
which of these it is most similar.
Analysis
The Eulerian method is more similar to control volume analysis. In both cases, mass moves into and out
of the flow domain or control volume, and we don’t follow any particular chunk of fluid. Instead we analyze whatever fluid
happens to be inside the control volume at the time.
Discussion
In fact, the Eulerian analysis is the same as a control volume analysis except that Eulerian analysis is
usually applied to infinitesimal volumes and differential equations of fluid flow, whereas control volume analysis usually
refers to finite volumes and integral equations of fluid flow.
4-13C
Solution
flow.
We are to define a steady flow field in the Eulerian description, and discuss particle acceleration in such a
Analysis
A flow field is defined as steady in the Eulerian frame of reference when properties at any point in the
flow field do not change with respect to time. In such a flow field, individual fluid particles may still experience non-zero
acceleration – the answer to the question is yes.
Discussion
Although velocity is not a function of time in a steady flow field, its total derivative with respect to time
G
G
a = dV / dt is not necessarily zero since the acceleration is composed of a local (unsteady) part which is zero and an
(
)
advective part which is not necessarily zero.
4-14C
Solution
We are to list three alternate names for material derivative.
Analysis
The material derivative is also called total derivative, particle derivative, Eulerian derivative,
Lagrangian derivative, and substantial derivative. “Total” is appropriate because the material derivative includes both
local (unsteady) and convective parts. “Particle” is appropriate because it stresses that the material derivative is one
following fluid particles as they move about in the flow field. “Eulerian” is appropriate since the material derivative is used
to transform from Lagrangian to Eulerian reference frames. “Lagrangian” is appropriate since the material derivative is
used to transform from Lagrangian to Eulerian reference frames. Finally, “substantial” is not as clear of a term for the
material derivative, and we are not sure of its origin.
Discussion
All of these names emphasize that we are following a fluid particle as it moves through a flow field.
4-5
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-15
Solution
We are to calculate the material acceleration for a given velocity field.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
The velocity field is
Analysis
G
G
G
V = ( u , v ) = (U 0 + bx ) i − byj
(1)
The acceleration field components are obtained from its definition (the material acceleration) in Cartesian coordinates,
∂u
∂u
∂u
∂u
+u
+v
+w
= 0 + (U 0 + bx ) b + ( −by ) 0 + 0
∂t
∂x
∂y
∂z
∂v
∂v
∂v
∂v
ay =
+ u + v + w = 0 + (U 0 + bx ) 0 + ( −by )( −b ) +0
∂t
∂x
∂y
∂z
ax =
(2)
where the unsteady terms are zero since this is a steady flow, and the terms with w are zero since the flow is twodimensional. Eq. 2 simplifies to
ax = b (U 0 + bx )
Material acceleration components:
In terms of a vector,
Material acceleration vector:
ay = b2 y
(3)
G
G
G
a = b (U 0 + bx ) i + b 2 yj
(4)
Discussion
For positive x and b, fluid particles accelerate in the positive x direction. Even though this flow is steady,
there is still a non-zero acceleration field.
4-16
Solution
particle.
For a given pressure and velocity field, we are to calculate the rate of change of pressure following a fluid
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
Analysis
The pressure field is
P = P0 −
Pressure field:
ρ⎡
2U 0 bx + b 2 ( x 2 + y 2 ) ⎤
2⎣
⎦
(1)
By definition, the material derivative, when applied to pressure, produces the rate of change of pressure following a fluid
particle. Using Eq. 1 and the velocity components from the previous problem,
∂P
∂P
DP ∂P
+u
+v
+
=
∂x
∂y
∂t
Dt N
Steady
(
∂P
w
∂z
N
(2)
Two-dimensional
)
(
= (U 0 + bx ) − ρU 0 b − ρ b 2 x + ( −by ) − ρ b 2 y
)
where the unsteady term is zero since this is a steady flow, and the term with w is zero since the flow is two-dimensional.
Eq. 2 simplifies to the following rate of change of pressure following a fluid particle:
(
)
DP
2
= ρ ⎡ −U 0 b − 2U 0 b 2 x + b3 y 2 − x 2 ⎤
⎣
⎦
Dt
(3)
Discussion
The material derivative can be applied to any flow property, scalar or vector. Here we apply it to the
pressure, a scalar quantity.
4-6
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-17
Solution
For a given velocity field we are to calculate the acceleration.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The velocity components are
Velocity components:
u = 1.1 + 2.8 x + 0.65 y
v = 0.98 − 2.1x − 2.8 y
(1)
The acceleration field components are obtained from its definition (the material acceleration) in Cartesian coordinates,
∂u
∂u
∂u
∂u
+u
+v
+w
= 0 + (1.1 + 2.8 x + 0.65 y )( 2.8 ) + ( 0.98 − 2.1x − 2.8 y )( 0.65 ) + 0
∂t
∂x
∂y
∂z
∂v
∂v
∂v
∂v
+ u + v + w = 0 + (1.1 + 2.8 x + 0.65 y )( −2.1) + ( 0.98 − 2.1x − 2.8 y )( −2.8 ) +0
ay =
∂t
∂x
∂y
∂z
ax =
(2)
where the unsteady terms are zero since this is a steady flow, and the terms with w are zero since the flow is twodimensional. Eq. 2 simplifies to
Acceleration components:
ax = 3.717 + 6.475 x
a y = −5.054 + 6.475 y
(3)
At the point (x,y) = (-2,3), the acceleration components of Eq. 3 are
Acceleration components at (-2,3):
ax = −9.233 ≅ -9.23
a y = 14.371 ≅ 14.4
Discussion
The final answers are given to three significant digits. No units are given in either the problem statement or
the answers. We assume that the coefficients have appropriate units.
4-18
Solution
For a given velocity field we are to calculate the acceleration.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The velocity components are
Velocity components:
u = 0.20 + 1.3 x + 0.85 y
v = −0.50 + 0.95 x − 1.3 y
(1)
The acceleration field components are obtained from its definition (the material acceleration) in Cartesian coordinates,
∂u
∂u
∂u
∂u
+u
+v
+w
= 0 + ( 0.20 + 1.3 x + 0.85 y )(1.3) + ( −0.50 + 0.95 x − 1.3 y )( 0.85 ) + 0
∂t
∂x
∂y
∂z
∂v
∂v
∂v
∂v
+ u + v + w = 0 + ( 0.20 + 1.3 x + 0.85 y )( 0.95 ) + ( −0.50 + 0.95 x − 1.3 y )( −1.3 ) +0
ay =
∂t
∂x
∂y
∂z
ax =
(2)
where the unsteady terms are zero since this is a steady flow, and the terms with w are zero since the flow is twodimensional. Eq. 2 simplifies to
Acceleration components:
ax = −0.165 + 2.4975 x
a y = 0.84 + 2.4975 y
(3)
At the point (x,y) = (1,2), the acceleration components of Eq. 3 are
Acceleration components at (1,2):
ax = 2.3325 ≅ 2.33
a y = 5.835 ≅ 5.84
Discussion
The final answers are given to three significant digits. No units are given in either the problem statement or
the answers. We assume that the coefficients have appropriate units.
4-7
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-19
Solution
We are to generate an expression for the fluid acceleration for a given velocity.
Assumptions
1 The flow is steady. 2 The flow is axisymmetric. 3 The water is incompressible.
Analysis
In Problem 4-2 we found that along the centerline,
u = uentrance +
Speed along centerline of nozzle:
( uexit − uentrance )
x2
(1)
∂u
∂u
∂u
∂u
+u
+v
+w
∂x
∂y
∂t
∂z
(2)
L2
To find the acceleration in the x-direction, we use the material acceleration,
ax =
Acceleration along centerline of nozzle:
The first term in Eq. 2 is zero because the flow is steady. The last two terms are zero because the flow is axisymmetric,
which means that along the centerline there can be no v or w velocity component. We substitute Eq. 1 for u to obtain
Acceleration along centerline of nozzle:
ax = u
( uexit − uentrance ) 2 ⎞ ( uexit − uentrance )
∂u ⎛
= ⎜ uentrance +
x ⎟ ( 2)
x
⎜
⎟
∂x ⎝
L2
L2
⎠
(3)
or
ax = 2uentrance
Discussion
( uexit − uentrance )
L2
x+2
( uexit − uentrance )
L4
2
x3
(4)
Fluid particles are accelerated along the centerline of the nozzle, even though the flow is steady.
4-20
Solution
We are to write an equation for centerline speed through a diffuser, given that the flow speed decreases
parabolically.
Assumptions
1 The flow is steady. 2 The flow is axisymmetric.
Analysis
A general equation for a parabola in x is
General parabolic equation:
u = a + b ( x − c)
2
(1)
We have two boundary conditions, namely at x = 0, u = uentrance and at x = L, u = uexit. By inspection, Eq. 1 is satisfied by
setting c = 0, a = uentrance and b = (uexit - uentrance)/L2. Thus, Eq. 1 becomes
Parabolic speed:
Discussion
u = uentrance +
( uexit − uentrance )
L2
x2
(2)
You can verify Eq. 2 by plugging in x = 0 and x = L.
4-8
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-21
Solution
We are to generate an expression for the fluid acceleration for a given velocity, and then calculate its value
at two x locations.
Assumptions
1 The flow is steady. 2 The flow is axisymmetric.
Analysis
In the previous problem, we found that along the centerline,
u = uentrance +
Speed along centerline of diffuser:
( uexit − uentrance )
2
L
x2
(1)
To find the acceleration in the x-direction, we use the material acceleration,
Acceleration along centerline of diffuser:
ax =
∂u
∂u
∂u
∂u
+w
+u
+v
∂z
∂t
∂x
∂y
(2)
The first term in Eq. 2 is zero because the flow is steady. The last two terms are zero because the flow is axisymmetric,
which means that along the centerline there can be no v or w velocity component. We substitute Eq. 1 for u to obtain
Acceleration along centerline of diffuser:
( uexit − uentrance ) x 2 ⎞ ( uexit − uentrance ) x
∂u ⎛
= ⎜ uentrance +
ax = u
⎟⎟ ( 2 )
∂x ⎜⎝
L2
L2
⎠
or
ax = 2uentrance
( uexit − uentrance )
2
L
x+2
( uexit − uentrance )
2
4
L
x3
(3)
At the given locations, we substitute the given values. At x = 0,
Acceleration along centerline of diffuser at x = 0:
ax ( x = 0 ) = 0
(4)
At x = 1.0 m,
Acceleration along centerline of diffuser at x = 1.0 m:
ax ( x = 1.0 m ) = 2 ( 30.0 m/s )
( −25.0 m/s )
( −25.0 m/s )
3
(1.0 m ) + 2
(1.0 m )
2
4
( 2.0 m )
( 2.0 m )
2
(5)
= -297 m/s 2
Discussion
ax is negative implying that fluid particles are decelerated along the centerline of the diffuser, even though
the flow is steady. Because of the parabolic nature of the velocity field, the acceleration is zero at the entrance of the
diffuser, but its magnitude increases rapidly downstream.
4-9
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
Flow Patterns and Flow Visualization
4-22C
Solution
We are to define streamline and discuss what streamlines indicate.
Analysis
A streamline is a curve that is everywhere tangent to the instantaneous local velocity vector. It
indicates the instantaneous direction of fluid motion throughout the flow field.
Discussion
If a flow field is steady, streamlines, pathlines, and streaklines are identical.
4-23
Solution
For a given velocity field we are to generate an equation for the streamlines.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
The steady, two-dimensional velocity field of Problem 4-15 is
G
G
G
V = ( u , v ) = (U 0 + bx ) i − byj
(1)
Analysis
Velocity field:
For two-dimensional flow in the x-y plane, streamlines are given by
Streamlines in the x-y plane:
dy ⎞
v
=
dx ⎟⎠along a streamline u
(2)
We substitute the u and v components of Eq. 1 into Eq. 2 and rearrange to get
dy
−by
=
dx U 0 + bx
We solve the above differential equation by separation of variables:
−∫
dy
dx
=
by ∫ U 0 + bx
Integration yields
1
1
1
− ln ( by ) = ln (U 0 + bx ) + ln C1
b
b
b
(3)
where we have set the constant of integration as the natural logarithm of some constant C1, with a constant in front in order
to simplify the algebra (notice that the factor of 1/b can be removed from each term in Eq. 3). When we recall that ln(ab) =
lna + lnb, and that –lna = ln(1/a), Eq. 3 simplifies to
Equation for streamlines:
y=
C
U
( 0 + bx )
(4)
The new constant C is related to C1, and is introduced for simplicity.
Discussion
Each value of constant C yields a unique streamline of the flow.
4-10
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-24E
Solution
For a given velocity field we are to plot several
streamlines for a given range of x and y values.
3
Assumptions 1 The flow is steady. 2 The flow is two-dimensional in
the x-y plane.
2
Analysis
From the solution to the previous problem, an equation
for the streamlines is
1
Streamlines in the x-y plane:
y=
C
(U 0 + bx )
(1)
y 0
(ft)
Constant C is set to various values in order to plot the streamlines.
Several streamlines in the given range of x and y are plotted in Fig. 1.
The direction of the flow is found by calculating u and v at
some point in the flow field. We choose x = 1 ft, y = 1 ft. At this point u
= 9.6 ft/s and v = –4.6 ft/s. The direction of the velocity at this point is
obviously to the lower right. This sets the direction of all the
streamlines. The arrows in Fig. 1 indicate the direction of flow.
-1
-2
-3
0
1
Discussion
The flow is type of converging channel flow.
4-25C
Solution
We are to determine what kind of flow visualization is seen in a photograph.
2
3
x (ft)
4
5
FIGURE 1
Streamlines (solid blue curves) for the given
velocity field; x and y are in units of ft.
Analysis
Since the picture is a snapshot of dye streaks in water, each streak shows the time history of dye that was
introduced earlier from a port in the body. Thus these are streaklines. Since the flow appears to be steady, these streaklines
are the same as pathlines and streamlines.
Discussion
It is assumed that the dye follows the flow of the water. If the dye is of nearly the same density as the water,
this is a reasonable assumption.
4-26C
Solution
We are to define pathline and discuss what pathlines indicate.
Analysis
A pathline is the actual path traveled by an individual fluid particle over some time period. It indicates
the exact route along which a fluid particle travels from its starting point to its ending point. Unlike streamlines, pathlines
are not instantaneous, but involve a finite time period.
Discussion
If a flow field is steady, streamlines, pathlines, and streaklines are identical.
4-27C
Solution
We are to define streakline and discuss the difference between streaklines and streamlines.
Analysis
A streakline is the locus of fluid particles that have passed sequentially through a prescribed point in
the flow. Streaklines are very different than streamlines. Streamlines are instantaneous curves, everywhere tangent to the
local velocity, while streaklines are produced over a finite time period. In an unsteady flow, streaklines distort and then
retain features of that distorted shape even as the flow field changes, whereas streamlines change instantaneously with the
flow field.
Discussion
If a flow field is steady, streamlines and streaklines are identical.
4-11
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-28C
Solution
We are to determine what kind of flow visualization is seen in a photograph.
Analysis
Since the picture is a snapshot of dye streaks in water, each streak shows the time history of dye that was
introduced earlier from a port in the body. Thus these are streaklines. Since the flow appears to be unsteady, these
streaklines are not the same as pathlines or streamlines.
Discussion
It is assumed that the dye follows the flow of the water. If the dye is of nearly the same density as the water,
this is a reasonable assumption.
4-29C
Solution
We are to determine what kind of flow visualization is seen in a photograph.
Analysis
Since the picture is a snapshot of smoke streaks in air, each streak shows the time history of smoke that was
introduced earlier from the smoke wire. Thus these are streaklines. Since the flow appears to be unsteady, these streaklines
are not the same as pathlines or streamlines.
Discussion
It is assumed that the smoke follows the flow of the air. If the smoke is neutrally buoyant, this is a
reasonable assumption. In actuality, the smoke rises a bit since it is hot; however, the air speeds are high enough that this
effect is negligible.
4-30C
Solution
We are to determine what kind of flow visualization is seen in a photograph.
Analysis
Since the picture is a time exposure of air bubbles in water, each white streak shows the path of an
individual air bubble. Thus these are pathlines. Since the outer flow (top and bottom portions of the photograph) appears to
be steady, these pathlines are the same as streaklines and streamlines.
Discussion
It is assumed that the air bubbles follow the flow of the water. If the bubbles are small enough, this is a
reasonable assumption.
4-31C
Solution
We are to define timeline and discuss how timelines can be produced in a water channel. We are also to
describe an application where timelines are more useful than streaklines.
Analysis
A timeline is a set of adjacent fluid particles that were marked at the same instant of time. Timelines
can be produced in a water flow by using a hydrogen bubble wire. There are also techniques in which a chemical reaction is
initiated by applying current to the wire, changing the fluid color along the wire. Timelines are more useful than streaklines
when the uniformity of a flow is to be visualized. Another application is to visualize the velocity profile of a boundary layer
or a channel flow.
Discussion
Timelines differ from streamlines, streaklines, and pathlines even if the flow is steady.
4-32C
Solution
For each case we are to decide whether a vector plot or contour plot is most appropriate, and we are to
explain our choice.
Analysis
In general, contour plots are most appropriate for scalars, while vector plots are necessary when vectors are
to be visualized.
(a) A contour plot of speed is most appropriate since fluid speed is a scalar.
(b) A vector plot of velocity vectors would clearly show where the flow separates. Alternatively, a vorticity contour
plot of vorticity normal to the plane would also show the separation region clearly.
(c) A contour plot of temperature is most appropriate since temperature is a scalar.
(d) A contour plot of this component of vorticity is most appropriate since one component of a vector is a scalar.
Discussion
There are other options for case (b) – temperature contours can also sometimes be used to identify a
separation zone.
4-12
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-33
Solution
For a given velocity field we are to generate an equation for the streamlines and sketch several streamlines
in the first quadrant.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The velocity field is given by
G
G
G
V = ( u , v ) = ( 0.5 + 1.2 x ) i + ( −2.0 − 1.2 y ) j
(1)
For two-dimensional flow in the x-y plane, streamlines are given by
dy ⎞
v
=
⎟
dx ⎠along a streamline u
Streamlines in the x-y plane:
(2)
We substitute the u and v components of Eq. 1 into Eq. 2 and rearrange to get
dy −2.0 − 1.2 y
=
dx
0.5 + 1.2 x
We solve the above differential equation by separation of variables:
dy
dx
=
−2.0 − 1.2 y 0.5 + 1.2 x
→
dy
dx
∫ −2.0 − 1.2 y = ∫ 0.5 + 1.2 x
Integration yields
−
1
1
1
ln ( −2.0 − 1.2 y ) =
ln ( 0.5 + 1.2 x ) −
ln C1
1.2
1.2
1.2
where we have set the constant of integration as the natural logarithm of
some constant C1, with a constant in front in order to simplify the
algebra. When we recall that ln(ab) = lna + lnb, and that –lna = ln(1/a),
Eq. 3 simplifies to
Equation for streamlines:
y=
5
y
4
3
2
C
− 1.667
1.2 ( 0.5 + 1.2 x )
1
The new constant C is related to C1, and is introduced for simplicity. C
can be set to various values in order to plot the streamlines. Several
streamlines in the upper right quadrant of the given flow field are shown
in Fig. 1.
The direction of the flow is found by calculating u and v at some
point in the flow field. We choose x = 3, y = 3. At this point u = 4.1 and v
= -5.6. The direction of the velocity at this point is obviously to the lower
right. This sets the direction of all the streamlines. The arrows in Fig. 1
indicate the direction of flow.
Discussion
6
(3)
0
0
1
2
3
4
5
x
FIGURE 1
Streamlines (solid black curves) for the
given velocity field.
The flow appears to be a counterclockwise turning flow in the upper right quadrant.
4-13
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-34
Solution
For a given velocity field we are to generate a velocity
vector plot in the first quadrant.
Scale:
6
Assumptions 1 The flow is steady. 2 The flow is two-dimensional in
the x-y plane.
Analysis
The velocity field is given by
G
G
G
V = ( u , v ) = ( 0.5 + 1.2 x ) i + ( −2.0 − 1.2 y ) j
5
y 4
3
(1)
2
At any point (x,y) in the flow field, the velocity components u and v are
obtained from Eq. 1,
Velocity components:
u = 0.5 + 1.2 x
v = −2.0 − 1.2 y
10 m/s
1
0
(2)
0
To plot velocity vectors, we simply pick an (x,y) point, calculate u and v
from Eq. 2, and plot an arrow with its tail at (x,y), and its tip at
(x+Su,y+Sv) where S is some scale factor for the vector plot. For the
vector plot shown in Fig. 1, we chose S = 0.2, and plot velocity
vectors at several locations in the first quadrant.
1
2
3
The flow appears to be a counterclockwise turning flow in the upper right quadrant.
4-35
Solution
For a given velocity field we are to generate an acceleration vector plot in the first quadrant.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The velocity field is given by
G
G
G
V = ( u , v ) = ( 0.5 + 1.2 x ) i + ( −2.0 − 1.2 y ) j
(1)
At any point (x,y) in the flow field, the velocity components u and v are
obtained from Eq. 1,
u = 0.5 + 1.2 x
v = −2.0 − 1.2 y
Scale:
(2)
5
4
y
(3)
3
2
1
0
0
where the unsteady terms are zero since this is a steady flow, and the terms
with w are zero since the flow is two-dimensional. Eq. 3 simplifies to
Acceleration components:
ax = 0.6 + 1.44 x
a y = 2.4 + 1.44 y
10 m/s2
6
The acceleration field is obtained from its definition (the material
acceleration),
Acceleration components:
∂u
∂u
∂u
∂u
+u
+v
+w
= 0 + ( 0.5 + 1.2 x )(1.2 ) + 0 + 0
ax =
∂t
∂x
∂y
∂z
∂v
∂v
∂v
∂v
+ u + v + w = 0 + 0 + ( −2.0 − 1.2 y )( −1.2 ) +0
ay =
∂t
∂x
∂y
∂z
5
FIGURE 1
Velocity vectors for the given velocity field.
The scale is shown by the top arrow.
Discussion
Velocity components:
4
x
(4)
1
2
3
4
5
x
FIGURE 1
Acceleration vectors for the velocity field.
The scale is shown by the top arrow.
To plot the acceleration vectors, we simply pick an (x,y) point, calculate ax
and ay from Eq. 4, and plot an arrow with its tail at (x,y), and its tip at (x+Sax,y+Say) where S is some scale factor for
the vector plot. For the vector plot shown in Fig. 1, we chose S = 0.15, and plot acceleration vectors at several
locations in the first quadrant.
Discussion
Since the flow is a counterclockwise turning flow in the upper right quadrant, the acceleration vectors point
to the upper right (centripetal acceleration).
4-14
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-36
For the given velocity field, the location(s) of stagnation point(s) are to be determined. Several velocity
Solution
vectors are to be sketched and the velocity field is to be described.
Assumptions 1 The flow is steady and incompressible. 2 The flow is two-dimensional, implying no z-component of
velocity and no variation of u or v with z.
Analysis
(a) The velocity field is
G
G
G
V = ( u , v ) = (1 + 2.5 x + y ) i + ( −0.5 − 1.5 x − 2.5 y ) j
Scale:
(1)
5
G
G
Since V is a vector, all its components must equal zero in order for V
itself to be zero. Setting each component of Eq. 1 to zero,
Simultaneous equations:
x = -0.421 m
4
3
u = 1 + 2.5 x + y = 0
v = −0.5 − 1.5 x − 2.5 y = 0
y
2
We can easily solve this set of two equations and two unknowns
simultaneously. Yes, there is one stagnation point, and it is located at
Stagnation point:
10 m/s
1
0
y = 0.0526 m
(b) The x and y components of velocity are calculated from Eq. 1 for
several (x,y) locations in the specified range. For example, at the point (x =
2 m, y = 3 m), u = 9.00 m/s and v = -11 m/s. The magnitude of velocity (the
speed) at that point is 14.21 m/s. At this and at an array of other locations,
the velocity vector is constructed from its two components, the results of
which are shown in Fig. 1. The flow can be described as a
counterclockwise turning, accelerating flow from the upper left to the lower
right. The stagnation point of Part (a) does not lie in the upper right
quadrant, and therefore does not appear on the sketch.
-1
0
1
2
3
4
5
x
FIGURE 1
Velocity vectors in the upper right quadrant
for the given velocity field.
Discussion
The stagnation point location is given to three significant digits. It will be verified in Chap. 9 that this flow
field is physically valid because it satisfies the differential equation for conservation of mass.
4-15
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-37
For the given velocity field, the material acceleration is to be calculated at a particular point and plotted at
Solution
several locations in the upper right quadrant.
Assumptions 1 The flow is steady and incompressible. 2 The flow is two-dimensional, implying no z-component of
velocity and no variation of u or v with z.
Analysis
(a) The velocity field is
G
G
G
V = ( u , v ) = (1 + 2.5 x + y ) i + ( −0.5 − 1.5 x − 2.5 y ) j
(1)
Using the velocity field of Eq. 1 and the equation for material acceleration in Cartesian coordinates, we write expressions
for the two non-zero components of the acceleration vector:
ax =
∂u
∂u
+u
∂t
∂x
+v
∂u
∂y
+w
∂u
∂z
Scale:
= 0 + (1 + 2.5 x + y )( 2.5 ) + ( −0.5 − 1.5 x − 2.5 y )(1) + 0
10 m/s2
5
4
and
ay =
∂v
∂v
+u
∂t
∂x
+v
∂v
∂y
+w
∂v
∂z
= 0 + (1 + 2.5 x + y )( −1.5 ) + ( −0.5 − 1.5 x − 2.5 y )( −2.5 ) + 0
3
y
2
1
At (x = 2 m, y = 3 m), ax = 11.5 m/s2 and ay = 14.0 m/s2.
(b) The above equations are applied to an array of x and y values in the
upper right quadrant, and the acceleration vectors are plotted in Fig. 1.
Discussion
The acceleration vectors plotted in Fig. 1 point to the upper
right, increasing in magnitude away from the origin. This agrees
qualitatively with the velocity vectors of Fig. 1 of the previous problem;
namely, fluid particles are accelerated to the right and are turned in the
counterclockwise direction due to centripetal acceleration towards the
upper right. Note that the acceleration field is non-zero, even though the
flow is steady.
0
-1
0
1
2
3
4
5
x
FIGURE 1
Acceleration vectors in the upper right
quadrant for the given velocity field.
4-16
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-38
Solution
For a given velocity field we are to plot a velocity magnitude contour plot at five given values of speed.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the r-θ plane.
Analysis
Since ur = 0, and since ω is positive, the speed is equal to
the magnitude of the θ-component of velocity,
V=
Speed:
2
ur + uθ = uθ = ω r
N
2
2
1
0
Thus, contour lines of constant speed are simply circles of constant radius
given by
r=
Contour line of constant speed:
y
(m) 0
ω
-1
For example, at V = 2.0 m/s, the corresponding contour line is a circle
of radius 2.0 m,
Contour line at constant speed V = 2.0 m/s:
0.5 1.0 1.5
V
2.0 m/s
r=
= 2.0 m
1.0 1/s
We plot a circle at a radius of 2.0 m and repeat this simple calculation for
the four other values of V. We plot the contours in Fig. 1. The speed
increases linearly from the center of rotation (the origin).
2.0
-2
-2
-1
0
1
2
2.5
x (m)
FIGURE 1
Contour plot of velocity magnitude for solid
body rotation. Values of speed are labeled in
units of m/s.
Discussion
The contours are equidistant apart because of the linear nature of the velocity field.
4-39
Solution
For a given velocity field we are to plot a velocity magnitude contour plot at five given values of speed.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the r-θ plane.
Analysis
Since ur = 0, and since K is positive, the speed is equal to
the magnitude of the θ-component of velocity,
V=
Speed:
ur + uθ
N
2
0
2
K
= uθ =
r
Thus, contour lines of constant speed are simply circles of constant radius
given by
r=
Contour line of constant speed:
K
V
For example, at V = 2.0 m/s, the corresponding contour line is a circle
of radius 0.50 m,
Contour line at constant speed V = 2.0 m/s:
r=
1.0 m 2 /s
= 0.50 m
2.0 m/s
We plot a circle at a radius of 0.50 m and repeat this simple calculation for
the four other values of V. We plot the contours in Fig. 1. The speed near
the center is faster than that further away from the center.
Discussion
2
1.5
1
2.0
y
(m) 0
2.5
1.0
-1
0.5
-2
-2
-1
0
1
2
x (m)
FIGURE 1
Contour plot of velocity magnitude for a line
vortex. Values of speed are labeled in units
of m/s.
The contours are not equidistant apart because of the nonlinear nature of the velocity field.
4-17
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-40
Solution
For a given velocity field we are to plot a velocity magnitude contour plot at five given values of speed.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the r-θ plane.
Analysis
The velocity field is
Line source:
ur =
m
2π r
uθ = 0
(1)
Since uθ = 0, and since m is positive, the speed is equal to the magnitude of the r-component of velocity,
Speed:
m
V = ur 2 + uθ 2 = ur =
N
2π r
(2)
0
Thus, contour lines of constant speed are simply circles of constant radius
given by
Contour line of constant speed:
⎛ m ⎞
⎜ 2π ⎟
m
⎠
r=
=⎝
V
2π V
1.5
(3)
For example, at V = 2.0 m/s, the corresponding contour line is a circle
of radius 0.50 m,
Contour line at speed V = 2.0 m/s:
2
1.0 m 2 /s
r=
= 0.50 m
2.0 m/s
1
2.0
y
(m) 0
2.5
(4)
We plot a circle at a radius of 0.50 m and repeat this simple calculation for
the four other values of V. We plot the contours in Fig. 1. The flow slows
down as it travels further from the origin.
Discussion
The contours are not equidistant apart because of the
nonlinear nature of the velocity field.
1.0
-1
0.5
-2
-2
-1
0
1
2
x (m)
FIGURE 1
Contour plot of velocity magnitude for a line
source. Values of speed are labeled in units
of m/s.
4-18
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
Motion and Deformation of Fluid Elements
4-41C
Solution
We are to name and describe the four fundamental types of motion or deformation of fluid particles.
Analysis
1. Translation – a fluid particle moves from one location to another.
2. Rotation – a fluid particle rotates about an axis drawn through the particle.
3. Linear strain or extensional strain – a fluid particle stretches in a direction such that a line segment in that
direction is elongated at some later time.
4. Shear strain – a fluid particle distorts in such a way that two lines through the fluid particle that are initially
perpendicular are not perpendicular at some later time.
Discussion
In a complex fluid flow, all four of these occur simultaneously.
4-42
Solution
For a given velocity field, we are to determine whether the flow is rotational or irrotational.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
Analysis
The velocity field is
G
G
G
V = ( u , v ) = (U 0 + bx ) i − byj
(1)
By definition, the flow is rotational if the vorticity is non-zero. So, we calculate the vorticity. In a 2-D flow in the x-y plane,
the only non-zero component of vorticity is in the z direction, i.e. ζz,
Vorticity component in the z direction:
ζz =
∂v ∂u
−
= 0−0 = 0
∂x ∂y
(1)
Since the vorticity is zero, this flow is irrotational.
Discussion
We shall see in Chap. 10 that the fluid very close to the walls is rotational due to important viscous effects
near the wall (a boundary layer). However, in the majority of the flow field, the irrotational approximation is reasonable.
4-19
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-43
Solution
For a given velocity field we are to generate an equation for the x location of a fluid particle along the x-axis
as a function of time.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The velocity field is
Velocity field:
G
G
G
V = ( u , v ) = (U 0 + bx ) i − byj
(1)
We start with the definition of u following a fluid particle,
x-component of velocity of a fluid particle:
dxparticle
dt
= u = U 0 + bxparticle
(2)
where we have substituted u from Eq. 1. We rearrange and separate variables, dropping the “particle” subscript for
convenience,
dx
= dt
U 0 + bx
(3)
Integration yields
1
1
ln (U 0 + bx ) = t − ln C1
b
b
(4)
where we have set the constant of integration as the natural logarithm of some constant C1, with a constant in front in order
to simplify the algebra. When we recall that ln(ab) = lna + lnb, Eq. 4 simplifies to
ln ( C1 (U 0 + bx ) ) = t
from which
U 0 + bx = C2 ebt
(5)
where C2 is a new constant defined for convenience. We now plug in the known initial condition that at t = 0, x = xA to find
constant C2 in Eq. 5. After some algebra,
Fluid particle’s x location at time t:
Discussion
x = xA′ =
1
⎡(U 0 + bxA ) ebt − U 0 ⎤⎦
b⎣
(6)
We verify that at t = 0, x = xA in Eq. 6.
4-20
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-44
Solution
For a given velocity field we are to generate an equation for the change in length of a line segment moving
with the flow along the x-axis.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
Using the results of the previous problem,
Location of particle A at time t:
xA ′ =
1
⎡(U 0 + bxB ) ebt − U 0 ⎤⎦
b⎣
(1)
xB′ =
1
⎡(U 0 + bxB ) ebt − U 0 ⎤⎦
b⎣
(2)
and
Location of particle B at time t:
Since length ξ = xB – xA and length ξ + Δξ = xB′ – xA′, we write an expression for Δξ,
Change in length of the line segment:
Δξ = ( xB′ − xA′ ) − ( xB − xA )
1
1
⎡⎣(U 0 + bxB ) ebt − U 0 ⎤⎦ − ⎡⎣(U 0 + bxA ) ebt − U 0 ⎤⎦ − ( xB − xA )
b
b
= xB ebt − xA ebt − xB + xA
=
(3)
Eq. 3 simplifies to
Change in length of the line segment:
Discussion
(
)
Δξ = ( xB − xA ) ebt − 1
(4)
We verify from Eq. 4 that when t = 0, Δξ = 0.
4-21
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-45
Solution
By examining the increase in length of a line segment along the axis of a converging duct, we are to
generate an equation for linear strain rate in the x direction and compare to the exact equation given in this chapter.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
From the previous problem, we have an expression for the change in length of the line segment AB,
(
)
Δξ = ( xB − xA ) ebt − 1
Change in length of the line segment:
(1)
The fundamental definition of linear strain rate is the rate of increase in length of a line segment per unit length of the line
segment. For the case at hand,
Linear strain rate in x direction: ε xx =
d (ξ + Δξ ) − ξ d Δξ d Δξ
=
=
ξ
dt
dt ξ
dt xB − xA
(2)
We substitute Eq. 1 into Eq. 2 to obtain
Linear strain rate in x direction:
ε xx
(
)
bt
d ( xB − xA ) e − 1
d bt
e −1
=
=
dt
xB − xA
dt
(
)
(3)
In the limit as t → 0, we apply the first two terms of the series expansion for ebt,
Series expansion for ebt:
ebt = 1 + bt +
( bt )
2
+ ... ≈ 1 + bt
2!
(4)
Finally, for small t we approximate the time derivative as 1/t, yielding
Linear strain rate in x direction:
ε xx →
1
(1 + bt − 1) = b
t
(5)
∂u
=b
∂x
(6)
Comparing to the equation for εxx,
Linear strain rate in x direction:
ε xx =
Equations 5 and 6 agree, verifying our algebra.
Discussion
Although we considered a line segment on the x-axis, it turns out that εxx = b everywhere in the flow, as
seen from Eq. 6. We could also have taken the analytical time derivative of Eq. 3, yielding εxx = bebt. Then, as t → 0, εxx →
b.
4-22
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-46
Solution
time.
For a given velocity field we are to generate an equation for the y location of a fluid particle as a function of
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The velocity field is
Velocity field:
G
G
G
V = ( u , v ) = (U 0 + bx ) i − byj
(1)
We start with the definition of v following a fluid particle,
y-component of velocity of a fluid particle:
dyparticle
dt
= v = −byparticle
(2)
where we have substituted v from Eq. 1. We and rearrange and separate variables, dropping the “particle” subscript for
convenience,
dy
= −bdt
y
(3)
ln ( y ) = −bt − ln C1
(4)
Integration yields
where we have set the constant of integration as the natural logarithm of some constant C1, with a constant in front in order
to simplify the algebra. When we recall that ln(ab) = lna + lnb, Eq. 4 simplifies to
ln ( C1 y ) = −t
from which
y = C2 e −bt
(5)
where C2 is a new constant defined for convenience. We now plug in the known initial condition that at t = 0, y = yA to find
constant C2 in Eq. 5. After some algebra,
Fluid particle’s y location at time t:
y = yA′ = yA e −bt
(6)
Discussion
The fluid particle approaches the x-axis exponentially with time. The fluid particle also moves downstream
in the x direction during this time period. However, in this particular problem v is not a function of x, so the streamwise
movement is irrelevant (u and v act independently of each other).
4-23
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-47
Solution
direction.
For a given velocity field we are to generate an equation for the change in length of a line segment in the y
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
Using the results of the previous problem,
Location of particle A at time t:
yA′ = yA e −bt
(1)
yB′ = yB e − bt
(2)
and
Location of particle B at time t:
Since length η = yB – yA and length η + Δη = yB′ – yA′, we write an expression for Δη,
Change in length of the line segment:
Δη = ( yB′ − yA′ ) − ( yB − yA ) = yB e − bt − yA e − bt − ( yB − yA ) = yB e − bt − yA e − bt − yB + yA
which simplifies to
Change in length of the line segment:
Discussion
(
)
Δη = ( yB − yA ) e − bt − 1
(3)
We verify from Eq. 3 that when t = 0, Δη = 0.
4-24
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-48
Solution
By examining the increase in length of a line segment as it moves down a converging duct, we are to
generate an equation for linear strain rate in the y direction and compare to the exact equation given in this chapter.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
From the previous problem we have an expression for the change in length of the line segment AB,
(
)
Δη = ( yB − yA ) e − bt − 1
Change in length of the line segment:
(1)
The fundamental definition of linear strain rate is the rate of increase in length of a line segment per unit length of the line
segment. For the case at hand,
Linear strain rate in y direction:
ε yy =
d (η + Δη ) − η d Δη d Δη
=
=
η
dt
dt η
dt yB − yA
(2)
We substitute Eq. 1 into Eq. 2 to obtain
Linear strain rate in y direction:
ε yy
(
)
− bt
d ( y B − yA ) e − 1
d − bt
=
=
e −1
dt
yB − yA
dt
(
)
(3)
In the limit as t → 0, we apply the first two terms of the series expansion for e-bt,
Series expansion for e-bt:
e − bt = 1 + ( −bt ) +
( −bt )
2
+ ... ≈ 1 − bt
2!
(4)
Finally, for small t we approximate the time derivative as 1/t, yielding
Linear strain rate in y direction:
ε yy →
1
(1 − bt − 1) = −b
t
(5)
∂v
= −b
∂y
(6)
Comparing to the equation for ε,
Linear strain rate in y direction:
ε yy =
Equations 5 and 6 agree, verifying our algebra.
Discussion
Since v does not depend on x location in this particular problem, the algebra is simple. In a more general
case, both u and v depend on both x and y, and a numerical integration scheme is required. We could also have taken the
analytical time derivative of Eq. 3, yielding εyy = –be–bt. Then, as t → 0, εxx → –b.
4-25
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-49E
Solution
For a given velocity field and an initially square fluid particle, we are to calculate and plot its location and
shape after a given time period.
Assumptions
x-y plane.
1 The flow is steady. 2 The flow is two-dimensional in the
3
Analysis
Using the results of Problems 4-43 and 4-46, we can
calculate the location of any point on the fluid particle after the elapsed
time. We pick 6 points along each edge of the fluid particle, and plot their x
and y locations at t = 0 and at t = 0.2 s. For example, the point at the lower
left corner of the particle is initially at x = 0.25 ft and y = 0.75 ft at t = 0. At
t = 0.2 s,
2
Time t = 0
Time t = 0.2 s
1
y 0
x-location of lower left corner of the fluid particle at time t = 0.2 s:
1 ⎡
x=
( 5.0 ft/s + ( 4.6 1/s )( 0.25 ft ) ) e( 4.6 1/s)(0.2 s) − 5.0 ft/s ⎤⎦ = 2.268 ft
4.6 1/s ⎣
-1
-2
and
y-location of lower left corner of the fluid particle at time t = 0.2 s:
y = ( 0.75 ft ) e
− ( 4.6 1/s )( 0.2 s )
-3
= 0.2989 ft
0
1
2
3
4
5
x
We repeat the above calculations at all the points along the edges of the
fluid particle, and plot both their initial and final positions in Fig. 1 as dots.
Finally, we connect the dots to draw the fluid particle shape. It is clear
from the results that the fluid particle shrinks in the y direction and
stretches in the x direction. However, it does not shear or rotate.
FIGURE 1
Movement and distortion of an initially
square fluid particle in a converging duct; x
and y are in units of ft. Streamlines (solid
blue curves) are also shown for reference.
Discussion
The flow is irrotational since fluid particles do not rotate.
4-50E
Solution
By analyzing the shape of a fluid particle, we are to verify that the given flow field is incompressible.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
Since the flow is two-dimensional, we assume unit depth (1 ft) in the z direction (into the page in the
figure). In the previous problem, we calculated the initial and final locations of several points on the perimeter of an
initially square fluid particle. At t = 0, the particle volume is
Fluid particle volume at t = 0 s:
V = ( 0.50 ft )( 0.50 ft )(1.0 ft ) = 0.25 ft 3
(1)
At t = 0.2 s, the lower left corner of the fluid particle has moved to x = 2.2679 ft, y = 0.29889 ft, and the upper right corner
has moved to x = 3.5225 ft, y = 0.49815 ft. Since the fluid particle remains rectangular, we can calculate the fluid particle
volume from these two corner locations,
Fluid particle volume at t = 0.2 s:
V = ( 3.5225 ft − 2.2679 ft )( 0.49815 ft − 0.29889 ft )(1.0 ft ) = 0.2500 ft 3
(2)
Thus, to at least four significant digits, the fluid particle volume has not changed, and the flow is therefore
incompressible.
Discussion
The fluid particle stretches in the horizontal direction and shrinks in the vertical direction, but the net
volume of the fluid particle does not change.
4-26
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-51
Solution
For a given velocity field we are to use volumetric strain rate to verify that the flow field is incompressible..
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
The velocity field is
Analysis
Velocity field:
G
G
G
V = ( u , v ) = (U 0 + bx ) i − byj
(1)
We use the equation for volumetric strain rate in Cartesian coordinates, and apply Eq. 1,
Volumetric strain rate:
1 DV
∂u ∂v ∂w
= ε xx + ε yy + ε zz =
+
+
= b + ( −b ) + 0 = 0
V Dt
∂x ∂y ∂z
(2)
Where εzz = 0 since the flow is two-dimensional. Since the volumetric strain rate is zero everywhere, the flow is
incompressible.
Discussion
The fluid particle stretches in the horizontal direction and shrinks in the vertical direction, but the net
volume of the fluid particle does not change.
4-52
Solution
For a given steady two-dimensional velocity field, we are to calculate the x and y components of the
acceleration field.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
The velocity field is
G
G
G
V = ( u , v ) = (U + a1 x + b1 y ) i + (V + a2 x + b2 y ) j
Analysis
(1)
The acceleration field is obtained from its definition (the material acceleration). The x-component is
x-component of material acceleration:
∂u
∂u
∂u
∂u
ax =
+u
+v
+w
= (U + a1 x + b1 y ) a1 + (V + a2 x + b2 y ) b1
∂t
∂x
∂y N
∂z
N
Steady
(2)
Two-D
The y-component is
y-component of material acceleration:
∂v
∂v
∂v
∂v
+u +v + w
ay =
= (U + a1 x + b1 y ) a2 + (V + a2 x + b2 y ) b2
∂
∂
∂z
x
y
∂
t
N
N
Steady
Discussion
(3)
Two-D
If there were a z-component, it would be treated in the same fashion.
4-27
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-53
Solution
We are to find a relationship among the coefficients that causes the flow field to be incompressible.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
problem,
We use the equation for volumetric strain rate in Cartesian coordinates, and apply Eq. 1 of the previous
Volumetric strain rate:
1 DV
∂u ∂v ∂w
= a1 + b2
= ε xx + ε yy + ε zz =
+
+
V Dt
∂x ∂y N
∂z
(1)
Two-D
We recognize that when the volumetric strain rate is zero everywhere, the flow is incompressible. Thus, the desired
relationship is
a1 + b2 = 0
Relationship to ensure incompressibility:
(2)
Discussion
If Eq. 2 is satisfied, the flow is incompressible, regardless of the values of the other coefficients.
4-54
Solution
For a given velocity field we are to calculate the linear strain rates in the x and y directions.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
We use the equations for linear strain rates in Cartesian coordinates, and apply Eq. 1 of Problem 4-52,
Linear strain rates:
Discussion
directions.
ε xx =
∂u
= a1
∂x
ε yy =
∂v
= b2
∂y
(1)
In general, since coefficients a1 and b2 are non-zero, fluid particles stretch (or shrink) in the x and y
4-55
Solution
For a given velocity field we are to calculate the shear strain rate in the x-y plane.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
We use the equation for shear strain rate εxy in Cartesian coordinates, and apply Eq. 1 of Problem 4-52,
Shear strain rate in x-y plane:
1 ⎛ ∂u ∂v ⎞ 1
+ ⎟ = ( b1 + a2 )
2 ⎝ ∂y ∂x ⎠ 2
ε xy = ε yx = ⎜
(1)
Note that by symmetry εyx = εxy.
Discussion
directions.
In general, since coefficients b1 and a2 are non-zero, fluid particles distort via shear strain in the x and y
4-28
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-56
Solution
For a given velocity field we are to form the 2-D strain rate tensor and determine the conditions necessary
for the x and y axes to be principal axes.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
The two-dimensional form of the strain rate tensor is
⎛ ε xx
ε xy ⎞
⎟
ε
ε
yy ⎠
⎝ yx
ε ij = ⎜
2-D strain rate tensor:
(1)
We use the linear strain rates and the shear strain rate from the previous two problems to generate the tensor,
2-D strain rate tensor:
⎛ ε xx
ε ij = ⎜
⎝ ε yx
⎛
ε xy ⎞ ⎜
⎟=⎜
ε yy ⎠ ⎜ 1
⎜
⎝2
a1
( b1 + a2 )
1
( b1 + a2 ) ⎞⎟
2
⎟
⎟
b2
⎟
⎠
(2)
If the x and y axes were principal axes, the diagonals of εij would be non-zero, and the off-diagonals would be zero. Here
the off-diagonals go to zero when
Condition for x and y axes to be principal axes:
b1 + a2 = 0
(3)
For the more general case in which Eq. 3 is not satisfied, the principal axes can be calculated using tensor
Discussion
algebra.
4-57
Solution
For a given velocity field we are to calculate the vorticity vector and discuss its orientation.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
G
We use the equation for vorticity vector ζ in Cartesian coordinates, and apply Eq. 1 of Problem 4-52,
Analysis
Vorticity vector:
⎛
⎞ ⎛
⎞
G
⎜ ∂w
∂w ⎟ G ⎛ ∂v ∂u ⎞ G
∂v ⎟ G ⎜ ∂u
ζ =⎜
−
−
⎟i + ⎜
⎟ j + ⎜ − ⎟ k = ( a2 − b1 ) k
∂z N
∂x ⎟
∂z ⎟ ⎜ N
∂y N
⎜N
⎝ ∂x ∂y ⎠
⎜
⎟ ⎝ Two-D Two-D
Two-D
⎠
⎝ Two-D
⎠
G
(1)
The only non-zero component of vorticity is in the z (or –z) direction.
Discussion
For any two-dimensional flow in the x-y plane, the vorticity vector must point in the z (or –z) direction. The
sign of the z-component of vorticity in Eq. 1 obviously depends on the sign of a2 – b1.
4-29
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-58
Solution
For the given velocity field we are to calculate the two-dimensional linear strain rates from fundamental
principles and compare with the given equation.
Assumptions
1 The flow is incompressible. 2 The flow is steady. 3 The flow is two-dimensional.
First, for convenience, we number the equations in the problem statement:
G
G
G
V = ( u , v ) = ( a + by ) i + 0 j
Velocity field:
(1)
Analysis
( x + ( a + by ) dt , y )
Lower left corner at t + dt:
ε xx =
Linear strain rate in Cartesian coordinates:
∂u
∂x
ε yy =
∂v
∂y
(2)
(3)
(a)
The lower right corner of the fluid particle moves the same amount as the lower left corner since u does not
depend on y position. Thus,
( x + dx + ( a + by ) dt, y )
Lower right corner at t + dt:
(4)
Similarly, the top two corners of the fluid particle move to the right at speed a + b(y+dy)dt. Thus,
Upper left corner at t + dt:
( x + ( a + b ( y + dy ) ) dt, y + dy )
(5)
( x + dx + ( a + b ( y + dy ) ) dt, y + dy )
(6)
and
Upper right corner at t + dt:
(b)
From the fundamental definition of linear strain rate in the x-direction, we consider the lower edge of the fluid
particle. Its rate of increase in length divided by its original length is found by using Eqs. 2 and 4,
εxx:
Length of lower edge at t + dt
⎡
Length of lower
P edge at t ⎤
⎢ x + dx + ( a + by ) dt − ( x + ( a + by ) dt ) −
⎥
dx
1
⎥=0
ε xx = ⎢
⎥
dt ⎢
dx
⎢
⎥
⎣
⎦
(6)
We get the same result by considering the upper edge of the fluid particle. Similarly, using the left edge of the fluid particle
and Eqs. 2 and 5 we get
εyy:
ε yy
left edge at t ⎤
⎡ Length of left
edgeat t + dt Length ofP
⎢
⎥
y + dy − y −
dy
1
= ⎢
⎥=0
dt ⎢
dy
⎥
⎣⎢
⎦⎥
(7)
We get the same result by considering the right edge of the fluid particle. Thus both the x- and y-components of linear strain
rate are zero for this flow field.
(c)
From Eq. 3 we calculate
Linear strain rates:
ε xx =
∂u
=0
∂x
ε yy =
∂v
=0
∂y
(8)
Discussion
Although the algebra in this problem is rather straight-forward, it is good practice for the more general case
(a later problem).
4-30
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-59
Solution
We are to verify that the given flow field is incompressible using two different methods.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional.
Analysis
(a)
The volume of the fluid particle at time t is.
Volume at time t:
V ( t ) = dxdydz
(1)
where dz is the length of the fluid particle in the z direction. At time t + dt, we assume that the fluid particle’s dimension dz
remains fixed since the flow is two-dimensional. Thus its volume is dz times the area of the rhombus shown in Fig. P4-58,
as illustrated in Fig. 1,
Volume at time t + dt:
V ( t + dt ) = dxdydz
(2)
(b)
We use the equation for volumetric strain rate in Cartesian
coordinates, and apply the results of the previous problem,
Volumetric strain rate:
1 DV
= ε xx + ε yy + ε zz = 0 + 0 + 0 = 0
V Dt
(3)
Where εzz = 0 since the flow is two-dimensional. Since the volumetric
strain rate is zero everywhere, the flow is incompressible.
dy
dy
Since Eqs. 1 and 2 are equal, the volume of the fluid particle has not
changed, and the flow is therefore incompressible.
dx
dx
FIGURE 1
The area of a rhombus is equal to its base
times its height, which here is dxdy.
Discussion
Although the fluid particle deforms with time, its height, its depth, and the length of its horizontal edges
remain constant.
4-31
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-60
Solution
For the given velocity field we are to calculate the two-dimensional shear strain rate in the x-y plane from
fundamental principles and compare with the given equation.
Assumptions 1 The flow is incompressible. 2 The flow is steady. 3 The
flow is two-dimensional.
( x + ( a + b ( y + dy )) dt, y + dy )
Analysis
(a)
The shear strain rate is
bdydt
Shear strain rate in Cartesian coordinates: ε xy =
1 ⎛ ∂u ∂v ⎞
+ ⎟
⎜
2 ⎝ ∂y ∂x ⎠
(1)
β
dy
From the fundamental definition of shear strain rate in the x-y plane, we
consider the bottom edge and the left edge of the fluid particle, which
intersect at 90o at the lower left corner at time t. We define angle α between
the lower edge and the left edge of the fluid particle, and angle β, the
complement of α (Fig. 1). The rate of decrease of angle α over time
interval dt is obtained from application of trigonometry. First, we calculate
angle β,
Angle β at time t + dt:
⎛ bdydt ⎞
⎟ = arctan ( bdt ) ≈ bdt
⎝ dy ⎠
β = arctan ⎜
(2)
The approximation is valid for very small angles. As the time interval dt →
0, Eq. 2 is correct. At time t + dt, angle α is
Angle α at time t + dt:
α=
π
2
−β ≈
π
2
− bdt
dy
α
dx
( x + ( a + by ) dt , y )
( x + dx + ( a + by ) dt, y )
FIGURE 1
A magnified view of the deformed fluid
particle at time t + dt, with the location of
three corners indicated, and angles α and β
defined.
(3)
During this time interval, α changes from 90o (π/2 radians) to the expression given by Eq. 2. Thus the rate of change of α is
Rate of change of angle α:
⎡
⎤
1 ⎢⎛ π
dα
⎞ π ⎥
= ⎢⎜ − bdt ⎟ −
⎥ = −b
dt
dt ⎢⎝ 2
2 ⎥
⎠ N
α at t
⎣ α at t + dt
⎦
(4)
Finally, since shear strain rate is defined as half of the rate of decrease of angle α,
ε xy = −
Shear strain rate:
(b)
1 dα b
=
2
2 dt
(5)
From Eq. 1 we calculate
Shear strain rate:
b
1 ⎛ ∂u ∂v ⎞ 1
+ ⎟ = (b + 0) =
2
2 ⎝ ∂y ∂x ⎠ 2
ε xy = ⎜
(6)
Both methods for obtaining the shear strain rate agree (Eq. 5 and Eq. 6).
Discussion
Although the algebra in this problem is rather straight-forward, it is good practice for the more general case
(a later problem).
4-32
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-61
Solution
For the given velocity field we are to calculate the two-dimensional rate of rotation in the x-y plane from
fundamental principles and compare with the given equation.
Assumptions
1 The flow is incompressible. 2 The flow is steady. 3 The flow is two-dimensional.
( x + ( a + b ( y + dy )) dt, y + dy )
Analysis
(a)
The rate of rotation in Cartesian coordinates is
Rate of rotation in Cartesian coordinates:
1 ⎛ ∂v ∂u ⎞
− ⎟
2 ⎝ ∂x ∂y ⎠
ωz = ⎜
bdydt
(1)
β
From the fundamental definition of rate of rotation in the x-y plane, we
consider the bottom edge and the left edge of the fluid particle, which
intersect at 90o at the lower left corner at time t. We define angle β in Fig.
1, where β is the negative of the angle of rotation of the left edge of the
fluid particle (negative because rotation is mathematically positive in the
counterclockwise direction). We calculate angle β using trigonometry,
Angle β at time t + dt:
⎛ bdydt ⎞
⎟ = arctan ( bdt ) ≈ bdt
⎝ dy ⎠
β = arctan ⎜
dx
( x + ( a + by ) dt , y )
( x + dx + ( a + by ) dt, y )
(2)
The approximation is valid for very small angles. As the time interval dt →
0, Eq. 2 is correct. Meanwhile, the bottom edge of the fluid particle has not
rotated at all. Thus, the average angle of rotation of the two line segments
(lower and left edges) at time t + dt is
AVG =
dy
1
b
( 0 − β ) ≈ − dt
2
2
FIGURE 1
A magnified view of the deformed fluid
particle at time t + dt, with the location of
three corners indicated, and angle β defined.
(3)
Thus the average rotation rate during time interval dt is
Rate of rotation in x-y plane:
(b)
ωz =
d ( AVG )
b
1⎛ b ⎞
− dt ⎟ = −
⎜
2
dt ⎝ 2 ⎠
(4)
b
1 ⎛ ∂v ∂u ⎞ 1
− ⎟ = (0 − b) = −
2
2 ⎝ ∂x ∂y ⎠ 2
(5)
dt
=
From Eq. 1 we calculate
Rate of rotation:
ωz = ⎜
Both methods for obtaining the rate of rotation agree (Eq. 4 and Eq. 5).
Discussion
The rotation rate is negative, indicating clockwise rotation about the z-axis. This agrees with our intuition as
we follow the fluid particle.
4-62
Solution
We are to determine whether the shear flow of Problem 4-22 is rotational or irrotational, and we are to
calculate the vorticity in the z direction.
Analysis
(a)
Since the rate of rotation is non-zero, it means that the flow is rotational.
(b)
Vorticity is defined as twice the rate of rotation, or twice the angular velocity. In the z direction,
Vorticity component:
Discussion
⎛ b⎞
ζ z = 2ω z = 2 ⎜ − ⎟ = −b
2
⎝
⎠
(1)
Vorticity is negative, indicating clockwise rotation about the z-axis.
4-33
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-63
Solution
We are to prove the given expression for flow in the xy-plane.
Assumptions
1 The flow is incompressible and two-dimensional.
Analysis
For flow in the xy-plane, we are to show that:
1 ⎛ ∂v ∂u ⎞
− ⎟
2 ⎝ ∂x ∂y ⎠
ω = ωz = ⎜
Rate of rotation:
(1)
By definition, the rate of rotation (angular velocity) at a point is the average rotation rate of two initially perpendicular lines
that intersect at the point. In this particular problem, Line a (PA) and Line b (PB) are initially perpendicular, and intersect at
point P. Line a rotates by angle αa, and Line b rotates by angle αb, Thus, the average angle of rotation is
αa + αb
Average angle of rotation:
(2)
2
During time increment dt, point P moves a distance udt to the right and vdt up (to first order, assuming dt is very small).
∂u ⎞
∂v ⎞
⎛
⎛
dx ⎟ dt to the right and ⎜ v + dx ⎟ dt up, and point B moves a distance
Similarly, point A moves a distance ⎜ u +
x
∂
∂x ⎠
⎝
⎠
⎝
αb
⎛
⎛
∂u ⎞
∂v ⎞
dy ⎟ dt to the right and ⎜ v + dy ⎟ dt up. Since point A is initially
⎜u +
y
y ⎠
∂
∂
⎝
⎠
⎝
at distance dx to the right of point P, the horizontal distance from point P′
to point A′ at the later time t2 is
Line b
∂u
dx +
dxdt
∂x
B′
On the other hand, point A is at the same vertical level as point P at time
t1. Thus, the vertical distance from point P′ to point A′ at time t2 is
∂v
dxdt
∂x
A′
∂v
dy + dydt
∂y
∂u
dydt
∂y
∂v
dxdt
∂x
Line a
(3)
αa
Similarly, point B is located at distance dy vertically above point P at time
t1, and thus the horizontal distance from point P′ to point B′ at time t2 is
−
Fluid element
at time t2
∂u
− dydt
∂y
P′
dx +
∂u
dxdt
∂x
(4)
FIGURE 1
A close-up view of the distorted fluid element
at time t2.
and
Vertical distance from point P′ to point B′ at time t2:
dy +
∂v
dydt
∂y
(5)
We mark the horizontal and vertical distances between point A′ and point P′ and between point B′ and point P′ at time t2 in
Fig. 1. From the figure we see that
Angle αa in terms of velocity components:
⎛ ∂v
⎞
⎛ ∂v
⎞
⎜ ∂x dxdt ⎟
⎜ ∂x dxdt ⎟
⎞ ∂v
−1
−1 ⎛ ∂v
dt
α a = tan ⎜
⎟ ≈ tan ⎜
⎟ = tan ⎜ dt ⎟ ≈
u
∂
dx
x
x
∂
∂
⎝
⎠
⎜⎜ dx +
⎟
⎜
⎟
dxdt ⎟
⎜
⎟
∂x
⎝
⎠
⎝
⎠
−1
(6)
The first approximation in Eq. 6 is due to the fact that as the size of the fluid element shrinks to a point, dx → 0, and at the
same time dt → 0. Thus, the second term in the denominator is second-order compared to the first-order term dx and can be
neglected. The second approximation in Eq. 6 is because as dt → 0 angle αa is very small, and tanαa → αa. Similarly, angle
αb is written in terms of velocity components as
4-34
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
∂u
⎛
⎞
⎛ ∂u
⎞
⎜ − ∂y dydt ⎟
⎜ − ∂y dydt ⎟
⎛ ∂u ⎞
∂u
−1
−1
⎟ ≈ tan ⎜
⎟ = tan −1 ⎜ − dt ⎟ ≈ − dt
α b = tan ⎜
∂
v
∂
∂y
dy
y
⎜ dy + dydt ⎟
⎜
⎟
⎝
⎠
⎜
⎟
⎜
⎟
∂y
⎝
⎠
⎝
⎠
(7)
Finally then, the average rotation angle (Eq. 2) becomes
Average angle of rotation:
αa + αb
2
=
∂u ⎞ dt ⎛ ∂v ∂u ⎞
1 ⎛ ∂v
dt ⎟ = ⎜ − ⎟
⎜ dt −
2 ⎝ ∂x
∂y ⎠ 2 ⎝ ∂x ∂y ⎠
(8)
and the average rate of rotation (angular velocity) of the fluid element about point P in the x-y plane becomes
ω = ωz =
Discussion
d ⎛ αa + αb
dt ⎝⎜ 2
⎞ 1 ⎛ ∂v ∂u ⎞
⎟= ⎜ − ⎟
⎠ 2 ⎝ ∂x ∂y ⎠
(9)
Eq. 9 can be extended to three dimensions by performing a similar analysis in the x-z and y-z planes.
4-35
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-64
Solution
We are to prove the given expression.
Assumptions
1 The flow is incompressible and two-dimensional.
Analysis
αb
Fluid element
at time t2
We are to prove the following:
Linear strain rate in x-direction:
ε xx =
∂u
∂x
(1)
By definition, the rate of linear strain is the rate of increase in length of a
line segment in a given direction divided by the original length of the line
segment in that direction. During time increment dt, point P moves a
distance udt to the right and vdt up (to first order, assuming dt is very
∂u ⎞
⎛
dx dt to the right and
small). Similarly, point A moves a distance ⎜ u +
∂x ⎟⎠
⎝
∂v ⎞
⎛
⎜ v + ∂x dx ⎟ dt up. Since point A is initially at distance dx to the right of
⎝
⎠
point P, its position to the right of point P′ at the later time t2 is
dx +
∂u
dxdt
∂x
(2)
On the other hand, point A is at the same vertical level as point P at time
t1. Thus, the vertical distance from point P′ to point A′ at time t2 is
Vertical distance from point P′ to point A′ at time t2:
B′
A′
Line a
∂v
dxdt
∂x
αa
P′
dx +
∂u
dxdt
∂x
FIGURE 1
A close-up view of the distorted fluid element
at time t2.
∂v
dxdt
∂x
(3)
We mark the horizontal and vertical distances between point A′ and point P′ at time t2 in Fig. 1. From the figure we see that
Linear strain rate in the x direction as line PA changes to P′A′ :
A ′ in x direction
⎛ Length of P′
⎞
Length of PA in x direction
P
⎜
⎟
∂u
dx +
dxdt −
dx
⎜
⎟ d ∂u
d
∂u
∂x
⎟ = ⎜⎛ dt ⎟⎞ =
ε xx = ⎜
dt ⎜
dx
dt
x
∂
∂x
⎟
⎝
⎠
N
Length of PA in x direction
⎜
⎟
⎜
⎟
⎝
⎠
(4)
Thus Eq. 1 is verified.
Discussion
The distortion of the fluid element is exaggerated in Fig. 1. As time increment dt and fluid element length
dx approach zero, the first-order approximations become exact.
4-36
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-65
Solution
We are to prove the given expression.
Assumptions
1 The flow is incompressible and two-dimensional.
Analysis
αa-b
αb
We are to prove the following:
Shear strain rate in xy-plane:
1 ⎛ ∂u ∂v ⎞
+ ⎟
2 ⎝ ∂y ∂x ⎠
ε xy = ⎜
Line b
(1)
B′
By definition, the shear strain rate at a point is half of the rate of decrease
of the angle between two initially perpendicular lines that intersect at the
point. In Fig. P4-63, Line a (PA) and Line b (PB) are initially
perpendicular, and intersect at point P. Line a rotates by angle αa, and
Line b rotates by angle αb. The angle between these two lines changes
from π/2 at time t1 to αa-b at time t2 as sketched in Fig. 1. The shear strain
rate at point P for initially perpendicular lines in the x and y directions is
thus
ε xy = −
1 d
α a-b
2 dt
A′
∂v
dy + dydt
∂y
Line a
αa
∂u
− dydt
∂y
P′
dx +
∂v
dxdt
∂x
∂u
dxdt
∂x
(2)
During time increment dt, point P moves a distance udt to the right and vdt
up (to first order, assuming dt is very small). Similarly, point A moves a
∂u ⎞
∂v ⎞
⎛
⎛
distance ⎜ u +
dx ⎟ dt to the right and ⎜ v + dx ⎟ dt up, and point B
∂x ⎠
∂x ⎠
⎝
⎝
FIGURE 1
A close-up view of the distorted fluid element
at time t2.
⎛
⎛
∂u ⎞
∂v ⎞
dy ⎟ dt to the right and ⎜ v + dy ⎟ dt up. Since point A is initially at distance dx to the right of
moves a distance ⎜ u +
∂y ⎠
∂y ⎠
⎝
⎝
point P, its position to the right of point P′ at the later time t2 is
Horizontal distance from point P′ to point A′ at time t2:
dx +
∂u
dxdt
∂x
(3)
On the other hand, point A is at the same vertical level as point P at time t1. Thus, the vertical distance from point P′ to
point A′ at time t2 is
Vertical distance from point P′ to point A′ at time t2:
∂v
dxdt
∂x
(3)
Similarly, point B is located at distance dy vertically above point P at time t1, and thus we write
Horizontal distance from point P′ to point B′ at time t2:
−
∂u
dydt
∂y
(4)
and
Vertical distance from point P′ to point B′ at time t2:
dy +
∂v
dydt
∂y
(5)
We mark the horizontal and vertical distances between point A′ and point P′ and between point B′ and point P′ at time t2 in
Fig. 1. From the figure we see that
Angle αa in terms of velocity components:
⎛ ∂v
⎞
⎛ ∂v
⎞
⎜ ∂x dxdt ⎟
⎜ ∂x dxdt ⎟
⎞ ∂v
−1
−1
−1 ⎛ ∂v
α a = tan ⎜
dt
⎟ ≈ tan ⎜
⎟ = tan ⎜ dt ⎟ ≈
∂
u
∂
dx
x
⎝
⎠ ∂x
⎜⎜ dx +
⎜⎜
⎟⎟
dxdt ⎟⎟
∂x
⎝
⎠
⎝
⎠
(6)
4-37
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
The first approximation in Eq. 6 is due to the fact that as the size of the fluid element shrinks to a point, dx → 0, and at the
same time dt → 0. Thus, the second term in the denominator is second-order compared to the first-order term dx and can be
neglected. The second approximation in Eq. 6 is because as dt → 0 angle αa is very small, and tanαa → αa. Similarly,
Angle αb in terms of velocity components:
∂u
⎛
⎞
⎛ ∂u
⎞
⎜ − ∂y dydt ⎟
⎜ − ∂y dydt ⎟
⎛ ∂u ⎞
∂u
⎟ ≈ tan −1 ⎜
⎟ = tan −1 ⎜ − dt ⎟ ≈ − dt
α b = tan −1 ⎜
v
∂
dy
∂y
⎜ dy + dydt ⎟
⎜
⎟
⎝ ∂y ⎠
⎜
⎟
⎜
⎟
∂y
⎝
⎠
⎝
⎠
(7)
Angle αa-b at time t2 is calculated from Fig. 1 as
Angle αa-b at time t2 in terms of velocity components:
α a-b =
π
2
+ αb − αa =
π
2
−
∂u
∂v
dt − dt
∂y
∂x
(8)
where we have used Eqs. 6 and 7. Finally then, the shear strain rate (Eq. 2) becomes
Shear strain rate, initially perpendicular lines in the x and y directions:
α a-b at t2
⎛
α a-bPat t1 ⎞
∂v
π ⎟ 1 ⎛ ∂u ∂v ⎞
1 d
1 1 ⎜ π ∂u
+ ⎟
ε xy = −
α a-b ≈ −
dt − dt −
⎜ −
⎟= ⎜
∂x
2 dt
2 dt ⎜ 2 ∂y
2 ⎟ 2 ⎝ ∂y ∂x ⎠
⎜
⎟
⎝
⎠
(9)
which agrees with Eq. 1. Thus, Eq. 1 is proven.
Discussion
y-z plane.
Eq. 9 can be easily extended to three dimensions by performing a similar analysis in the x-z plane and in the
4-66
Solution
For a given linear strain rate in the x-direction, we are to calculate the linear strain rate in the y-direction.
Analysis
Since the flow is incompressible, the volumetric strain rate must be zero. In two dimensions,
Volumetric strain rate in the x-y plane:
1 DV
∂u ∂v
= ε xx + ε yy =
+
=0
∂x ∂y
V Dt
(1)
Thus, the linear strain rate in the y-direction is the negative of that in the x-direction,
Linear strain rate in y-direction:
ε yy =
∂v
∂u
=−
= -2.5 1/s
∂y
∂x
(2)
Discussion
The fluid element stretches in the x-direction since εxx is positive. Because the flow is incompressible, the
fluid element must shrink in the y-direction, yielding a value of εyy that is negative.
4-38
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-67
Solution
axis.
We are to calculate the vorticity of fluid particles in a tank rotating in solid body rotation about its vertical
Assumptions
1 The flow is steady. 2 The z-axis is in the vertical direction.
Analysis
G
G
Vorticity ζ is twice the angular velocity ω . Here,
G
ω = 360
Angular velocity:
G
rot ⎛ 1 min ⎞ ⎛ 2π rad ⎞ G
k = 37.70k rad/s
⎜
⎟
⎜
⎟
min ⎝ 60 s ⎠ ⎝ rot ⎠
G
where k is the unit vector in the vertical (z) direction. The vorticity is thus
G
G
G
G
ζ = 2ω = 2 × 37.70k rad/s = 75.4k rad/s
Vorticity:
Discussion
upward.
(1)
(2)
Because the water rotates as a solid body, the vorticity is constant throughout the tank, and points vertically
4-68
Solution
We are to calculate the angular speed of a tank rotating about its vertical axis.
Assumptions
1 The flow is steady. 2 The z-axis is in the vertical direction.
G
G
Vorticity ζ is twice the angular velocity ω . Thus,
G
G
G
G ζ −55.4k rad/s
(1)
ω= =
= −27.7 k rad/s
Angular velocity:
2
2
G
where k is the unit vector in the vertical (z) direction. The angular velocity is negative, which by definition is in the
clockwise direction about the vertical axis. We express the rate of rotation in units of rpm,
Analysis
Rate of rotation:
Discussion
n = −27.7
rad ⎛ 60 s ⎞⎛ rot ⎞
rot
= −265
= -265 rpm
⎜
⎟⎜
⎟
s ⎝ 1 min ⎠⎝ 2π rad ⎠
min
(2)
Because the vorticity is constant throughout the tank, the water rotates as a solid body.
4-69
Solution
For a tank of given rim radius and speed, we are to calculate the magnitude of the component of vorticity in
the vertical direction.
Assumptions
1 The flow is steady. 2 The z-axis is in the vertical direction.
Analysis
The linear speed at the rim is equal to rrimωz. Thus,
ωz =
Component of angular velocity in z-direction:
Vrim 2.6 m/s
=
= 7.429 rad/s
rrim
0.35 m
(1)
G
G
Vorticity ζ is twice the angular velocity ω . Thus,
z-component of vorticity:
ζ z = 2ω z = 2 ( 7.429 rad/s ) = 14.86 rad/s ≅ 15.0 rad/s
(2)
Discussion
Radian is a non-dimensional unit, so we can insert it into Eq. 1. The final answer is given to two significant
digits for consistency with the given information.
4-39
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-70C
Solution
We are to explain the relationship between vorticity and rotationality.
Analysis
Vorticity is a measure of the rotationality of a fluid particle. If a particle rotates, its vorticity is non-zero.
Mathematically, the vorticity vector is twice the angular velocity vector.
Discussion
If the vorticity is zero, the flow is called irrotational.
4-71
Solution
direction.
For a given deformation of a fluid particle in one direction, we are to calculate its deformation in the other
Assumptions
1 The flow is incompressible. 2 The flow is two-dimensional in the x-y plane.
Analysis
Since the flow is incompressible and two-dimensional, the area of the fluid element must remain constant
(volumetric strain rate must be zero in an incompressible flow). The area of the original fluid particle is a2. Hence, the
vertical dimension of the fluid particle at the later time must be a2/2a = a/2.
Discussion
direction.
Since the particle stretches by a factor of two in the x-direction, it shrinks by a factor of two in the y-
4-72
Solution
deformation.
We are to calculate the percentage change in fluid density for a fluid particle undergoing two-dimensional
Assumptions
1 The flow is two-dimensional in the x-y plane.
Analysis
The area of the original fluid particle is a2. Assuming that the mass of the fluid particle is m and its
dimension in the z-direction is also a, the initial density is ρ = m/V = m/a3. As the particle moves and deforms, its mass
must remain constant. If its dimension in the z-direction remains equal to a, the density at the later time is
Density at the later time:
ρ=
m
m
m
=
= 1.013 3
a
V (1.06a )( 0.931a )( a )
(1)
Compared to the original density, the density has increased by about 1.3%.
Discussion
The fluid particle has stretched in the x-direction and shrunk in the y-direction, but there is nevertheless a
net decrease in volume, corresponding to a net increase in density.
4-73
Solution
For a given velocity field we are to calculate the vorticity.
Analysis
The velocity field is
G
G
G
G
V = ( u , v, w ) = ( 3.0 + 2.0 x − y ) i + ( 2.0 x − 2.0 y ) j + ( 0.5 xy ) k
(1)
In Cartesian coordinates, the vorticity vector is
Vorticity vector in Cartesian coordinates:
G
⎛ ∂w ∂v ⎞ G ⎛ ∂u ∂w ⎞ G ⎛ ∂v ∂u ⎞ G
− ⎟i + ⎜
−
⎟ j + ⎜ ∂x − ∂y ⎟ k
⎝ ∂y ∂z ⎠ ⎝ ∂z ∂x ⎠
⎝
⎠
ζ =⎜
(2)
We substitute the velocity components u = 3.0 + 2.0x – y, v = 2.0x – 2.0y, and w = 0.5xy from Eq. 1 into Eq. 2 to obtain
G
G
G
G
G
G
G
ζ = ( 0.5 x − 0 ) i + ( 0 − 0.5 y ) j + ( 2.0 − ( −1) ) k = ( 0.5 x ) i − ( 0.5 y ) j + ( 3.0 ) k
Vorticity vector:
(3)
Discussion
The vorticity is non-zero implying that this flow field is rotational.
4-40
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-74
Solution
We are to determine if the flow is rotational, and if so calculate the z-component of vorticity.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
The velocity field is given by
Analysis
G
G
⎛ y ⎞G
V = ( u, v ) = ⎜ V ⎟ i + 0 j
⎝ h⎠
Velocity field, Couette flow:
(1)
If the vorticity is non-zero, the flow is rotational. So, we calculate the z-component of vorticity,
ζz =
z-component of vorticity:
V
V
∂v ∂u
−
= 0− = −
∂x ∂y
h
h
(2)
Since vorticity is non-zero, this flow is rotational. Furthermore, the vorticity is negative, implying that particles rotate in
the clockwise direction.
Discussion
The vorticity is constant at every location in this flow.
4-75
Solution
For the given velocity field for Couette flow, we are to calculate the two-dimensional linear strain rates and
the shear strain rate.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
Analysis
The linear strain rates in the x direction and in the y direction are
ε xx =
Linear strain rates:
∂u
=0
∂x
ε yy =
∂v
=0
∂y
(1)
The shear strain rate in the x-y plane is
Shear strain rate:
1 ⎛ ∂u ∂v ⎞ 1 ⎛ V
⎞ V
+ ⎟ = ⎜ + 0⎟ =
2 ⎝ ∂y ∂x ⎠ 2 ⎝ h
⎠ 2h
ε xy = ⎜
(2)
Fluid particles in this flow have non-zero shear strain rate.
Discussion
Since the linear strain rates are zero, fluid particles deform (shear), but do not stretch in either the horizontal
or vertical directions.
4-41
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-76
Solution
For the Couette flow velocity field we are to form the 2-D strain rate tensor and determine if the x and y
axes are principal axes.
Assumptions
Analysis
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
The two-dimensional strain rate tensor, εij, is
⎛ ε xx
ε xy ⎞
⎟
ε
ε
yy ⎠
⎝ yx
ε ij = ⎜
2-D strain rate tensor:
(1)
We use the linear strain rates and the shear strain rate from the previous problem to generate the tensor,
2-D strain rate tensor:
⎛ ε xx
ε ij = ⎜
⎝ ε yx
⎛
ε xy ⎞ ⎜ 0
⎟=⎜
ε yy ⎠ ⎜ V
⎜
⎝ 2h
V ⎞
2h ⎟⎟
0 ⎟⎟
⎠
(2)
Note that by symmetry εyx = εxy. If the x and y axes were principal axes, the diagonals of εij would be non-zero, and the offdiagonals would be zero. Here we have the opposite case, so the x and y axes are not principal axes.
Discussion
The principal axes can be calculated using tensor algebra.
4-42
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
Reynolds Transport Theorem
4-77C
Solution
(a) False: The statement is backwards, since the conservation laws are naturally occurring in the system form.
(b) False: The RTT can be applied to any control volume, fixed, moving, or deforming.
(c) True: The RTT has an unsteady term and can be applied to unsteady problems.
(d) True: The extensive property B (or its intensive form b) in the RTT can be any property of the fluid – scalar, vector, or
even tensor.
4-78
Solution
For the case in which Bsys is the mass m of a system, we are to use the RTT to derive the equation of
conservation of mass for a control volume.
Analysis
The general form of the Reynolds transport theorem is given by
dBsys
General form of the RTT:
dt
=
d
dt
G G
∫
CV
ρ bdV + ∫ ρ bVr ⋅ ndA
CS
(1)
Setting Bsys = m means that b = m/m = 1. Plugging these and dm/dt = 0 into Eq. 1 yields
0=
Conservation of mass for a CV:
Discussion
d
dt
∫
CV
G G
ρ dV + ∫ ρVr ⋅ ndA
CS
(2)
Eq. 2 is general and applies to any control volume – fixed, moving, or even deforming.
4-79
G
Solution
For the case in which Bsys is the linear momentum mV of a system, we are to use the RTT to derive the
equation of conservation of linear momentum for a control volume.
Analysis Newton’s second law is
G
G
G
G
dV
d
(1)
Newton’s second law for a system:
∑ F = ma = m dt = dt mV sys
G
G
G
Setting Bsys = mV means that b = mV m = V . Plugging these and Eq. 1 into the equation of the previous problem yields
( )
G
G
∑ F = dt ( mV )
d
sys
=
d
dt
G
G G G
)
G G G
)
(
∫
ρVdV + ∫ ρV Vr ⋅ n dA
∫
ρVdV + ∫ ρV Vr ⋅ n dA
CV
CS
or simply
Conservation of linear momentum for a CV:
G d
∑ F = dt
Discussion
CV
G
CS
(
(2)
Eq. 2 is general and applies to any control volume – fixed, moving, or even deforming.
4-43
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-80
G
Solution
For the case in which Bsys is the angular momentum H of a system, we are to use the RTT to derive the
equation of conservation of angular momentum for a control volume.
The conservation of angular momentum is expressed as
Analysis
G
G
G
G
Setting Bsys = H means that b = r × mV
(
)
d G
∑ M = dt H
Conservation of angular momentum for a system:
(1)
sys
G G
m = r × V , noting that m = constant for a system. Plugging these and Eq. 1 into
the equation of Problem 4-78 yields
G
d G
∑ M = dt H
sys
=
d
dt
∫
CV
G
(G )
G
( G )(
G G
)
ρ r × V dV + ∫ ρ r × V Vr ⋅ n dA
CS
or simply
Conservation of angular momentum for a CV:
G d
G G
G G G G
∑ M = dt ∫CV ρ r × V dV + ∫CS ρ r × V Vr ⋅ n dA
(
)
(
)(
)
(2)
Discussion
Eq. 2 is general and applies to any control volume – fixed, moving, or even deforming.
4-81
Solution
F(t) is to be evaluated from the given expression.
Analysis
The integral is
F (t ) =
d
dt
∫
x = Bt
x = At
e −2 x dx
2
(1)
We could try integrating first, and then differentiating, but we can instead use the 1-D Leibnitz theorem. Here,
G ( x,t ) = e −2 x (G is not a function of time in this simple example). The limits of integration are a(t) = At and b(t) = Bt.
2
Thus,
F (t ) = ∫
b
a
=
db
da
∂G
dx + G ( b,t ) −
G ( a,t )
∂t
dt
dt
0
+ Be
−2 b 2
− Ae
(2)
−2 a 2
or
F ( t ) = Be − B t − Ae− A t
2 2
Discussion
2 2
(3)
You are welcome to try to obtain the same solution without using the Leibnitz theorem.
4-44
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
Review Problems
4-82
Solution
We are to determine if the flow is rotational, and if so calculate the z-component of vorticity.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
The velocity components are given by
Analysis
Velocity components, 2-D Poiseuille flow:
u=
(
1 dP 2
y − hy
2 μ dx
)
v=0
(1)
If the vorticity is non-zero, the flow is rotational. So, we calculate the z-component of vorticity,
z-component of vorticity:
ζz =
∂v ∂u
1 dP
1 dP
−
= 0−
(2 y − h) = −
(2 y − h)
∂x ∂y
2 μ dx
2 μ dx
(2)
Since vorticity is non-zero, this flow is rotational. Furthermore, in the lower half of the flow (y < h/2) the vorticity is
negative (note that dP/dx is negative). Thus, particles rotate in the clockwise direction in the lower half of the flow.
Similarly, particles rotate in the counterclockwise direction in the upper half of the flow.
Discussion
The vorticity varies linearly across the channel.
4-83
Solution
For the given velocity field for 2-D Poiseuille flow, we are to calculate the two-dimensional linear strain
rates and the shear strain rate.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
Analysis
The linear strain rates in the x direction and in the y direction are
ε xx =
Linear strain rates:
∂u
=0
∂x
ε yy =
∂v
=0
∂y
(1)
The shear strain rate in the x-y plane is
Shear strain rate:
⎞ 1 dP
1 ⎛ ∂u ∂v ⎞ 1 ⎛ 1 dP
+ ⎟= ⎜
(2 y − h) + 0⎟ =
( 2 y − h)
2 ⎝ ∂y ∂x ⎠ 2 ⎝ 2 μ dx
⎠ 4μ dx
ε xy = ⎜
(2)
Fluid particles in this flow have non-zero shear strain rate.
Discussion
Since the linear strain rates are zero, fluid particles deform (shear), but do not stretch in either the horizontal
or vertical directions.
4-45
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-84
Solution
For the 2-D Poiseuille flow velocity field we are to form the 2-D strain rate tensor and determine if the x
and y axes are principal axes.
Assumptions
Analysis
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
The two-dimensional strain rate tensor, εij, in the x-y plane,
⎛ ε xx
ε xy ⎞
⎟
ε
ε
yy ⎠
⎝ yx
ε ij = ⎜
2-D strain rate tensor:
(1)
We use the linear strain rates and the shear strain rate from the previous problem to generate the tensor,
⎛
1 dP
0
( 2 y − h ) ⎞⎟
ε xy ⎞ ⎜
4 μ dx
⎟=⎜
ε yy ⎠ ⎜ 1 dP
0
( 2 y − h)
⎜
⎝ 4μ dx
⎛ ε xx
ε ij = ⎜
⎝ ε yx
⎟
⎟
⎟
⎠
(2)
Note that by symmetry εyx = εxy. If the x and y axes were principal axes, the diagonals of εij would be non-zero, and the offdiagonals would be zero. Here we have the opposite case, so the x and y axes are not principal axes.
Discussion
The principal axes can be calculated using tensor algebra.
4-85
Solution
For a given velocity field we are to plot several pathlines
for fluid particles released from various locations and over a specified time
period.
1.5
Assumptions 1 The flow is steady. 2 The flow is incompressible. 3 The
flow is two-dimensional in the x-y plane.
Properties
1
For water at 40oC, μ = 6.53×10-4 kg/m⋅s.
Analysis
Since the flow is steady, pathlines, streamlines, and
streaklines are all straight horizontal lines. We simply need to integrate
velocity component u with respect to time over the specified time period.
The horizontal velocity component is
u=
(
1 dP 2
y − hy
2μ dx
)
(1)
tend
tstart
(
0.5
0
0
0.5
1
1.5
x (m)
We integrate as follows:
x = xstart + ∫
y
(mm)
udt = 0 + ∫
10 s
0
⎛ 1 dP 2
⎞
y − hy ⎟ dt
⎜
⎝ 2μ dx
⎠
(
)
)
1 dP 2
x=
y − hy (10 s )
2 μ dx
(2)
FIGURE 1
Pathlines for the given velocity field at t =
12 s. Note that the vertical scale is greatly
expanded for clarity (x is in m, but y is in
mm).
We substitute the given values of y and the values of μ and dP/dx into Eq. 2 to calculate the ending x position of each
pathline. We plot the pathlines in Fig. 1.
Discussion
Streaklines introduced at the same locations and developed over the same time period would look identical
to the pathlines of Fig. 1.
4-46
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-86 [Also solved using EES on enclosed DVD]
Solution
For a given velocity field we are to plot several streaklines at a given time for dye released from various
locations over a specified time period.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
Properties
For water at 40oC, μ = 6.53×10-4 kg/m⋅s.
Analysis
Since the flow is steady, pathlines, streamlines, and
streaklines are all straight horizontal lines. We simply need to integrate
velocity component u with respect to time over the specified time period.
The horizontal velocity component is
u=
(
1 dP 2
y − hy
2μ dx
)
1
(1)
We integrate as follows to obtain the final x location of the first dye
particle released:
x = xstart + ∫
tend
tstart
(
udt = 0 + ∫
10 s
0
⎛ 1 dP 2
⎞
y − hy ⎟ dt
⎜
⎝ 2μ dx
⎠
(
1.5
y
(mm)
0.5
)
)
1 dP 2
x=
y − hy × (10 s )
2 μ dx
(2)
0
0
0.5
1
1.5
x (m)
We substitute the given values of y and the values of μ and dP/dx into Eq.
2 to calculate the ending x position of the first released dye particle of each
streakline. The last released dye particle is at x = xstart = 0, because it hasn’t
had a chance to go anywhere. We connect the beginning and ending points
to plot the streaklines (Fig. 1).
FIGURE 1
Streaklines for the given velocity field at t =
10 s. Note that the vertical scale is greatly
expanded for clarity (x is in m, but y is in
mm).
Discussion
These streaklines are introduced at the same locations and
are developed over the same time period as the pathlines of the previous problem. They are identical since the flow is
steady.
4-47
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-87
Solution
For a given velocity field we are to plot several streaklines at a given time for dye released from various
locations over a specified time period.
Assumptions 1 The flow is steady. 2 The flow is incompressible. 3 The
flow is two-dimensional in the x-y plane.
Properties
1.5
For water at 40oC, μ = 6.53×10-4 kg/m⋅s.
Analysis
Since the flow is steady, pathlines, streamlines, and
streaklines are all straight horizontal lines. The horizontal velocity
component is
u=
(
1 dP 2
y − hy
2μ dx
)
(1)
In the previous problem we generated streaklines at t = 10 s. Imagine the
dye at the source being suddenly cut off at that time, but the streaklines are
observed 2 seconds later, at t = 12 s. The dye streaks will not stretch any
further, but will simply move at the same horizontal speed for 2 more
seconds. At each y location, the x locations of the first and last dye particle
are thus
first dye particle of streakline:
(
)
(2)
(
)
(3)
x=
1 dP 2
y − hy (12 s )
2 μ dx
x=
1 dP 2
y − hy ( 2 s )
2μ dx
and
last dye particle of streakline:
1
y
(mm)
0.5
0
0
0.5
1
1.5
x (m)
FIGURE 1
Streaklines for the given velocity field at t =
12 s. Note that the vertical scale is greatly
expanded for clarity (x is in m, but y is in
mm).
We substitute the given values of y and the values of μ and dP/dx into Eqs. 2 and 3 to calculate the ending and beginning x
positions of the first released dye particle and the last released dye particle of each streakline. We connect the beginning
and ending points to plot the streaklines (Fig. 1).
Discussion
Both the left and right ends of each dye streak have moved by the same amount compared to those of the
previous problem.
4-88
Solution
For a given velocity field we are to compare streaklines at two different times and comment about linear
strain rate in the x direction.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is two-dimensional in the x-y plane.
Properties
For water at 40oC, μ = 6.53×10-4 kg/m⋅s.
Analysis
Comparing the results of the previous two problems we see that the streaklines have not stretched at all –
they have simply convected downstream. Thus, based on the fundamental definition of linear strain rate, it is zero:
ε xx = 0
Linear strain rate in the x direction:
Discussion
(1)
Our result agrees with that of Problem 4-83.
4-48
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-89
Solution
For a given velocity field we are to plot several timelines
at a specified time. The timelines are created by hydrogen bubbles
released from a vertical wire at x = 0.
1.5
Assumptions 1 The flow is steady. 2 The flow is incompressible. 3 The
flow is two-dimensional in the x-y plane.
Properties
For water at 40oC, μ = 6.53×10-4 kg/m⋅s.
Analysis
Since the flow is steady, pathlines, streamlines, and
streaklines are all straight horizontal lines, but timelines are completely
different from any of the others. To simulate a timeline, we integrate
velocity component u with respect to time over the specified time period
from t = 0 to t = tend. We introduce the bubbles at x = 0 and at many values
of y (we used 50 in our simulation). By connecting these x locations with
a line, we simulate a timeline. The horizontal velocity component is
(
1 dP 2
u=
y − hy
2μ dx
x-velocity component:
)
tend
tstart
→
x=
(
udt = 0 + ∫
tend
0
t4
t3
t2
t1
0.5
0
0
0.5
x (m)
1
1.5
FIGURE 1
Timelines for the given velocity field at t =
12.5 s, generated by a simulated hydrogen
bubble wire at x = 0. Timelines created at t5
= 10.0 s, t4 = 7.5 s, t3 = 5.0 s, t2 = 2.5 s, and
t1 = 0 s. Note that the vertical scale is greatly
expanded for clarity (x is in m, but y is in
mm).
⎛ 1 dP 2
⎞
y − hy ⎟ dt
⎜
dx
2
μ
⎝
⎠
(
t5
(1)
We integrate as follows to find the x position on the timeline at tend:
x = xstart + ∫
1
y
(mm)
)
)
1 dP 2
y − hy tend
2 μ dx
We substitute the values of y and the values of μ and dP/dx into the above equation to calculate the ending x position of
each point in the timeline. We repeat for the five values of tend. We plot the timelines in Fig. 1.
Discussion
Each timeline has the exact shape of the velocity profile.
4-90
Solution
We are to determine if the flow is rotational, and if so calculate the θ-component of vorticity.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is axisymmetric about the x axis.
Analysis
The velocity components are given by
u=
(
1 dP 2
r − R2
4 μ dx
)
ur = 0
uθ = 0
(1)
If the vorticity is non-zero, the flow is rotational. So, we calculate the θ-component of vorticity,
θ-component of vorticity:
ζθ =
∂ur ∂u
1 dP
r dP
−
= 0−
2r = −
∂z ∂r
4 μ dx
2 μ dx
(2)
Since the vorticity is non-zero, this flow is rotational. The vorticity is positive since dP/dx is negative. In this coordinate
system, positive vorticity is counterclockwise with respect to the positive θ direction. This agrees with our intuition since in
the top half of the flow, θ points out of the page, and the rotation is counterclockwise. Similarly, in the bottom half of the
flow, θ points into the page, and the rotation is clockwise.
Discussion
The vorticity varies linearly across the pipe from zero at the centerline to a maximum at the pipe wall.
4-49
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-91
Solution
For the given velocity field for axisymmetric Poiseuille flow, we are to calculate the linear strain rates and
the shear strain rate.
Assumptions
1 The flow is steady. 2 The flow is incompressible. 3 The flow is axisymmetric about the x axis.
Analysis
The linear strain rates in the x direction and in the r direction are
ε xx =
Linear strain rates:
∂u
=0
∂x
ε rr =
∂ur
=0
∂r
(1)
Thus there is no linear strain rate in either the x or the r direction. The shear strain rate in the x-r plane is
Shear strain rate:
1 ⎛ ∂u
∂u ⎞
1⎛
1 dP
⎞
r dP
ε xr = ⎜ r + ⎟ = ⎜ 0 +
2r ⎟ =
2 ⎝ ∂x ∂r ⎠ 2 ⎝
4 μ dx ⎠ 4μ dx
(2)
Fluid particles in this flow have non-zero shear strain rate.
Discussion
Since the linear strain rates are zero, fluid particles deform (shear), but do not stretch in either the horizontal
or radial directions.
4-92
Solution
For the axisymmetric Poiseuille flow velocity field we are to form the axisymmetric strain rate tensor and
determine if the x and r axes are principal axes.
Assumptions
Analysis
1 The flow is steady. 2 The flow is incompressible. 3 The flow is axisymmetric about the x axis.
The axisymmetric strain rate tensor, εij, is
⎛ ε rr
ε ij = ⎜
Axisymmetric strain rate tensor:
⎝ ε xr
ε rx ⎞
⎟
ε xx ⎠
(1)
We use the linear strain rates and the shear strain rate from the previous problem to generate the tensor,
Axisymmetric strain rate tensor:
⎛ ε rr
ε ij = ⎜
⎝ ε xr
⎛
0
ε rx ⎞ ⎜⎜
=
⎟
ε xx ⎠ ⎜ r dP
⎜
⎝ 4 μ dx
r dP ⎞
4 μ dx ⎟⎟
⎟
0 ⎟
⎠
(2)
Note that by symmetry εrx = εxr. If the x and r axes were principal axes, the diagonals of εij would be non-zero, and the offdiagonals would be zero. Here we have the opposite case, so the x and r axes are not principal axes.
Discussion
The principal axes can be calculated using tensor algebra.
4-50
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-93
Solution
We are to determine the location of stagnation point(s) in a given velocity field.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
The velocity components are
Analysis
x-component of velocity:
u=
x2 + y 2 + b2
−V x
4
2 2
π L x + 2 x y + 2 x2b2 + y 4 − 2 y 2b2 + b4
(1)
v=
x2 + y 2 − b2
−V y
π L x 4 + 2 x 2 y 2 + 2 x 2b2 + y 4 − 2 y 2b2 + b4
(2)
and
y-component of velocity:
Both u and v must be zero at a stagnation point. From Eq. 1, u can be zero only when x = 0. From Eq. 2, v can be zero either
when y = 0 or when x2 + y2 –b2 = 0. Combining the former with the result from Eq. 1, we see that there is a stagnation
point at (x,y) = (0,0), i.e. at the origin,
Stagnation point:
u = 0 and v = 0 at ( x, y ) = (0, 0)
(3)
Combining the latter with the result from Eq. 1, there appears to be another stagnation point at (x,y) = (0,b). However, at
that location, Eq. 2 becomes
y-component of velocity:
v=
0
0
−V b
=
π L b 4 − 2b 2 b 2 + b 4 0
(4)
This point turns out to be a singularity point in the flow. Thus, the location (0,b) is not a stagnation point after all.
Discussion
There is only one stagnation point in this flow, and it is at the origin.
4-51
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-94
Solution
We are to draw a velocity vector plot for a given velocity field.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
We generate an array of x and y values in the given range and calculate u and v from Eqs. 1 and 2
respectively at each location. We choose an appropriate scale factor for the vectors and then draw arrows to form the
velocity vector plot (Fig. 1).
10 m/s
Scale:
FIGURE 1
V
Velocity vector plot for the
0.02
vacuum cleaner; the scale
factor for the velocity vectors
is shown on the legend. x and
y
y values are in meters. The
vacuum cleaner inlet is at the
0.01
point x = 0, y = 0.02 m.
0
-0.03
-0.02
-0.01
0
0.01
0.02
0.03
x
It is clear from the velocity vector plot how the air gets sucked into the vacuum cleaner from all directions. We also see that
there is no flow through the floor.
Discussion
We discuss this problem in more detail in Chap. 10.
4-95
Solution
We are to calculate the speed of air along the floor due to a vacuum cleaner, and find the location of
maximum speed.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
Analysis
At the floor, y = 0. Setting y = 0 in Eq. 2 of Problem 4-93 shows that v = 0, as expected – no flow through
the floor. Setting y = 0 in Eq. 1 of Problem 4-93 results in the speed along the floor,
Speed on the floor:
u=
x 2 + b2
−V x
−V x x 2 + b 2
=
π L x 4 + 2 x 2b2 + b4 π L x 2 + b2
(
)
=
2
−V x
π L ( x 2 + b2 )
(1)
We find the maximum speed be differentiating Eq. 1 and setting the result to zero,
Maximum speed on the floor:
⎡
du −V ⎢ −2 x 2
=
dx π L ⎢ x 2 + b 2
⎣⎢
(
)
2
+
⎤
1 ⎥
=0
x 2 + b2 ⎥
⎦⎥
(2)
After some algebraic manipulation, we find that Eq. 2 has solutions at x = b and x = -b. It is at x = b and x = -b where we
expect the best performance. At the origin, directly below the vacuum cleaner inlet, the flow is stagnant. Thus, despite our
intuition, the vacuum cleaner will work poorly directly below the inlet.
Discussion
Try some experiments at home to verify these results!
4-52
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-96
Solution
For a given expression for u, we are to find an expression for v such that the flow field is incompressible.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane.
The x-component of velocity is given as
Analysis
u = a + b ( x − c)
x-component of velocity:
2
(1)
In order for the flow field to be incompressible, the volumetric strain rate must be zero,
Volumetric strain rate:
1 DV
∂u ∂v ∂w
=0
= ε xx + ε yy + ε zz =
+
+
∂x ∂y N
∂z
V Dt
(2)
Two-D
This gives us a necessary condition for v,
∂v
∂u
=−
∂y
∂x
Necessary condition for v:
(3)
We substitute Eq. 1 into Eq. 3 and integrate to solve for v,
Expression for v:
∂v
∂u
=−
= −2b ( x − c )
∂y
∂x
∂v
v = ∫ dy = ∫ ( −2b ( x − c ) ) dy + f ( x )
∂y
Note that we must add an arbitrary function of x rather than a simple constant of integration since this is a partial integration
with respect to y. v is a function of both x and y. The result of the integration is
Expression for v:
Discussion
v = −2b ( x − c ) y + f ( x)
(4)
We verify by plugging Eqs. 1 and 4 into Eq. 2,
Volumetric strain rate:
1 DV ∂u ∂v
=
+
= 2b ( x − c ) − 2b ( x − c ) = 0
∂x ∂y
V Dt
(5)
Since the volumetric strain rate is zero for any function f(x), Eqs. 1 and 4 represent an incompressible flow field.
4-53
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-97
Solution
For a given velocity field we are to determine if the flow is rotational or irrotational.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the r-θ plane.
Analysis
The velocity components for flow over a circular cylinder of radius r are
⎛ a2 ⎞
ur = V cos θ ⎜ 1 − 2 ⎟
⎝ r ⎠
⎛ a2 ⎞
uθ = −V sin θ ⎜1 + 2 ⎟
⎝ r ⎠
(1)
Since the flow is assumed to be two-dimensional in the r-θ plane, the only non-zero component of vorticity is in the z
direction. In cylindrical coordinates,
1 ⎛ ∂ ( ruθ ) ∂ur
−
r ⎝ ∂r
∂θ
ζ z = ⎜⎜
Vorticity component in the z direction:
⎞
⎟⎟
⎠
(2)
We plug in the velocity components of Eq. 1 into Eq. 2 to solve for ζz,
⎛
1⎡ ∂ ⎛
a2
⎜⎜ −V sin θ ⎜ r +
r ⎣⎢ ∂r ⎝
r
⎝
ζz = ⎢
⎞⎤ 1 ⎡
⎤
a2
a2
⎟ ⎥ = ⎢ −V sin θ + V 2 sin θ + V sin θ − V 2 sin θ ⎥ = 0
r
r
r
⎠ ⎦⎥
⎣
⎦
⎞⎞
⎛ a2
⎟ ⎟⎟ + V sin θ ⎜1 − 2
⎠⎠
⎝ r
(3)
Hence, since the vorticity is everywhere zero, this flow is irrotational.
Discussion
Fluid particles distort as they flow around the cylinder, but their net rotation is zero.
4-98
Solution
For a given velocity field we are to find the location of the stagnation point.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the r-θ plane.
Analysis
The stagnation point occurs when both components of
velocity are zero. We set ur = 0 and uθ = 0 in Eq. 1 of the previous
problem,
⎛ a2
ur = V cos θ ⎜1 − 2
⎝ r
⎞
⎟ =0
⎠
⎛ a2
uθ = −V sin θ ⎜1 + 2
⎝ r
⎞
⎟=0
⎠
V
Stagnation
point
y
Either cos θ = 0 or r 2 = a 2
r=a
(1)
Either sin θ = 0 or r = − a
2
x
2
FIGURE 1
The stagnation point on the upstream half of
the flow field is located at the nose of the
cylinder at r = a and θ = 180o.
The second part of the uθ condition in Eq. 1 is obviously impossible since
cylinder radius a is a real number. Thus sinθ = 0, which means that θ = 0o
or 180o. We are restricted to the left half of the flow (x < 0); therefore we
choose θ = 180o. Now we look at the ur condition in Eq. 1. At θ = 180o, cosθ = -1, and thus we conclude that r must equal
a. Summarizing,
Stagnation point:
r=a
θ = −180o
(2)
Or, in Cartesian coordinates,
Stagnation point:
x = −a
y=0
(3)
The stagnation point is located at the nose of the cylinder (Fig. 1).
Discussion
This result agrees with our intuition, since the fluid must divert around the cylinder at the nose.
4-54
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-99
Solution
For a given stream function we are to generate an equation
for streamlines, and then plot several streamlines in the upstream half of
the flow field.
Assumptions
r-θ plane.
0.2
1 The flow is steady. 2 The flow is two-dimensional in the
y (m) 0
Analysis
(a) The stream function is
⎛
ψ = V sin θ ⎜ r −
⎝
a2 ⎞
⎟
r ⎠
-0.1
(1)
First we multiply both sides of Eq. 1 by r, and then solve the quadratic
equation for r using the quadratic rule. This gives us an equation for r as a
function of θ, with ψ, a, and V as parameters,
Equation for a streamline:
0.1
ψ ± ψ 2 + 4a 2V 2 sin 2 θ
r=
2V sin θ
(2)
-0.2
-0.4
-0.3
-0.2
x (m)
-0.1
0
FIGURE 1
Streamlines corresponding to flow over a
circular cylinder. Only the upstream half of
the flow field is plotted.
(b) For the particular case in which V = 1.00 m/s and cylinder radius a = 10.0 cm, we choose various values of ψ in Eq. 2,
and plot streamlines in the upstream half of the flow (Fig. 1). Each value of ψ corresponds to a unique streamline.
Discussion
The stream function is discussed in greater detail in Chap. 9.
4-100
Solution
For a given velocity field we are to calculate the linear strain rates εrr and εθθ in the r-θ plane.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the r-θ plane.
Analysis
We substitute the equation of Problem 4-97 into that of Problem 4-91,
ε rr =
Linear strain rate in r direction:
∂ur
a2
= 2V cos θ 3
∂r
r
(1)
and
Linear strain rate in θ direction:
1 ⎡ ∂u
⎤
1⎡
⎛
a2 ⎞
⎛
a2 ⎞⎤
a2
εθθ = ⎢ θ + ur ⎥ = ⎢ −V cos θ ⎜1 + 2 ⎟ + V cos θ ⎜ 1 − 2 ⎟ ⎥ = −2V cos θ 3
r ⎣ ∂θ
r ⎠
r
⎦ r ⎣⎢
⎝
⎝ r ⎠ ⎥⎦
(2)
The linear strain rates are non-zero, implying that fluid line segments do stretch (or shrink) as they move about in
the flow field.
Discussion
The linear strain rates decrease rapidly with distance from the cylinder.
4-55
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 4 Fluid Kinematics
4-101
Solution
We are to discuss whether the flow field of the previous problem is incompressible or compressible.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the r-θ plane.
Analysis
case,
For two-dimensional flow we know that a flow is incompressible if its volumetric strain rate is zero. In that
1 DV
∂u ∂v
= ε xx + ε yy =
+
=0
V Dt
∂x ∂y
(1)
∂u 1 ⎡ ∂u
1 DV
⎤
= ε rr + ε rθ = r + ⎢ θ + ur ⎥ = 0
∂r r ⎣ ∂θ
V Dt
⎦
(2)
1 DV
a2
a2
= 2V cos θ 3 − 2V cos θ 3 = 0
V Dt
r
r
(3)
Volumetric strain rate, incompressible 2-D flow in the x-y plane:
We can extend Eq. 1 to cylindrical coordinates by writing
Volumetric strain rate, incompressible 2-D flow in the r-θ plane:
Plugging in the results of the previous problem we see that
Volumetric strain rate for flow over a circular cylinder:
Since the volumetric strain rate is zero everywhere, the flow is incompressible.
Discussion
In Chap. 9 we show that Eq. 2 can be obtained from the differential equation for conservation of mass.
4-102
Solution
For a given velocity field we are to calculate the shear strain rate εrθ.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the r-θ plane.
Analysis
We substitute the equation of Problem 4-97 into that of Problem 4-91,
Shear strain rate in r-θ plane:
1⎡ ∂ ⎛u
ε rθ = ⎢ r ⎜ θ
2 ⎣ ∂r ⎝ r
=
⎞ 1 ∂ur ⎤
⎟ + r ∂θ ⎥
⎠
⎦
⎛ a2
a2 ⎞ 1 ⎛
1 ⎡ ∂ ⎛ V sin θ
− V sin θ 3 ⎟ + ⎜ −V sin θ ⎜ 1 − 2
⎢r ⎜ −
r
2 ⎣⎢ ∂r ⎝
r ⎠ r ⎝⎜
⎝ r
⎞ ⎞⎤
⎟ ⎟⎟ ⎥
⎠ ⎠ ⎦⎥
(1)
⎡1
a2 1 a2 ⎤
a2
1
= V sin θ ⎢ + 3 3 − + 3 ⎥ = 2V sin θ 3
r r ⎦
2
r
r
⎣r
which reduces to
Shear strain rate in r-θ plane:
ε rθ = 2V sin θ
a2
r3
(2)
The shear strain rate is non-zero, implying that fluid line segments do deform with shear as they move about in the
flow field.
Discussion
The shear strain rate decreases rapidly (as r-3) with distance from the cylinder.
KJ
4-56
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications
by Çengel & Cimbala
CHAPTER 5
MASS, BERNOULLI, AND ENERGY
EQUATIONS
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of The McGraw-Hill Companies, Inc.
(“McGraw-Hill”) and protected by copyright and other state and federal laws. By
opening and using this Manual the user agrees to the following restrictions, and if the
recipient does not agree to these restrictions, the Manual should be promptly returned
unopened to McGraw-Hill: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated
textbook. No other use or distribution of this Manual is permitted. This Manual
may not be sold and may not be distributed to or used by any student or other
third party. No part of this Manual may be reproduced, displayed or distributed
in any form or by any means, electronic or otherwise, without the prior written
permission of McGraw-Hill.
5-1
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
Conservation of Mass
5-1C
Solution
We are to name some conserved and non-conserved quantities.
Analysis
Mass, energy, momentum, and electric charge are conserved, and volume and entropy are not
conserved during a process.
Discussion
Students may think of other answers that may be equally valid.
5-2C
Solution
We are to discuss mass and volume flow rates and their relationship.
Analysis
Mass flow rate is the amount of mass flowing through a cross-section per unit time whereas volume flow
rate is the amount of volume flowing through a cross-section per unit time.
Discussion
Mass flow rate has dimensions of mass/time while volume flow rate has dimensions of volume/time.
5-3C
Solution
We are to discuss the mass flow rate entering and leaving a control volume.
Analysis
The amount of mass or energy entering a control volume does not have to be equal to the amount of mass
or energy leaving during an unsteady-flow process.
Discussion
If the process is steady, however, the two mass flow rates must be equal; otherwise the amount of mass
would have to increase or decrease inside the control volume, which would make it unsteady.
5-4C
Solution
We are to discuss steady flow through a control volume.
Analysis
Flow through a control volume is steady when it involves no changes with time at any specified position.
Discussion
This applies to any variable we might consider – pressure, velocity, density, temperature, etc.
5-5C
Solution
We are to discuss whether the flow is steady through a given control volume.
Analysis
No, a flow with the same volume flow rate at the inlet and the exit is not necessarily steady (unless the
density is constant). To be steady, the mass flow rate through the device must remain constant.
Discussion
If the question had stated that the two mass flow rates were equal, then the answer would be yes.
5-2
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-6E
Solution
A garden hose is used to fill a water bucket. The volume and mass flow rates of water, the filling time, and
the discharge velocity are to be determined.
Assumptions
splashing.
1 Water is an incompressible substance. 2 Flow through the hose is steady. 3 There is no waste of water by
Properties
We take the density of water to be 62.4 lbm/ft3.
Analysis
(a) The volume and mass flow rates of water are
V = AV = ( π D 2 / 4 )V = [ π ( 1 / 12 ft) 2 / 4 ]( 8 ft/s) = 0.04363 ft 3 /s ≅ 0.0436 ft 3 /s
= ρV = (62.4 lbm/ft 3 )(0.04363 ft 3 /s) = 2.72 lbm/s
m
(b) The time it takes to fill a 20-gallon bucket is
Δt =
⎞
⎛ 1 ft 3
20 gal
V
⎟ = 61.3 s
⎜
=
V 0.04363 ft 3 /s ⎜⎝ 7.4804 gal ⎟⎠
(c) The average discharge velocity of water at the nozzle exit is
Ve =
0.04363 ft 3 /s
V
V
=
=
= 32 ft/s
Ae πDe2 / 4 [π (0.5 / 12 ft) 2 / 4]
Discussion
Note that for a given flow rate, the average velocity is inversely proportional to the square of the velocity.
Therefore, when the diameter is reduced by half, the velocity quadruples.
5-7
Solution
Air is accelerated in a nozzle. The mass flow rate and the exit area of the nozzle are to be determined.
Assumptions
Flow through the nozzle is steady.
Properties
The density of air is given to be 2.21 kg/m3 at the inlet, and 0.762 kg/m3 at the exit.
Analysis
(a) The mass flow rate of air is determined from the inlet conditions to be
m = ρ 1 A1V1 = (2.21 kg/m 3 )(0.008 m 2 )(30 m/s) = 0.530 kg/s
1 = m
2 = m
.
(b) There is only one inlet and one exit, and thus m
Then the exit area of the nozzle is determined to be
m = ρ 2 A2V 2 ⎯
⎯→ A2 =
Discussion
m
ρ 2V 2
=
0.530 kg/s
3
(0.762 kg/ m )(180 m/s)
V1 = 30 m/s
A1 = 80 cm2
AIR
V2 = 180 m/s
= 0.00387 m 2 = 38.7 cm 2
Since this is a compressible flow, we must equate mass flow rates, not volume flow rates.
5-3
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-8
Solution
Air is expanded and is accelerated as it is heated by a hair dryer of constant diameter. The percent increase
in the velocity of air as it flows through the drier is to be determined.
Assumptions
Flow through the nozzle is steady.
Properties
The density of air is given to be 1.20 kg/m3 at the inlet, and 1.05 kg/m3 at the exit.
Analysis
1 = m
2 = m
. Then,
There is only one inlet and one exit, and thus m
m 1 = m 2
V2
ρ1 AV1 = ρ 2 AV2
V2 ρ1 1.20 kg/m3
=
=
= 1.14
V1 ρ 2 1.05 kg/m3
V1
(or, an increase of 14%)
Therefore, the air velocity increases 14% as it flows through the hair drier.
It makes sense that the velocity increases since the density decreases, but the mass flow rate is constant.
Discussion
5-9E
Solution
The ducts of an air-conditioning system pass through an open area. The inlet velocity and the mass flow rate
of air are to be determined.
Assumptions
Flow through the air conditioning duct is steady.
Properties
The density of air is given to be 0.078 lbm/ft3 at the inlet.
Analysis
The inlet velocity of air and the mass flow rate through the duct are
V1 =
V1
V1
450 ft 3 /min
=
=
= 825 ft/min = 13.8 ft/s
A1 π D 2 / 4 π (10/12 ft )2 / 4
450 ft3/min
AIR
D = 10 in
m = ρ 1V1 = (0.078 lbm/ft 3 )(450 ft 3 / min) = 35.1 lbm/min = 0.585 lbm/s
Discussion
The mass flow rate though a duct must remain constant in steady flow; however, the volume flow rate
varies since the density varies with the temperature and pressure in the duct.
5-10
Solution
A rigid tank initially contains air at atmospheric conditions. The tank is connected to a supply line, and air
is allowed to enter the tank until the density rises to a specified level. The mass of air that entered the tank is to be
determined.
Properties
The density of air is given to be 1.18 kg/m3 at the beginning, and 7.20 kg/m3 at the end.
Analysis
We take the tank as the system, which is a control volume since mass crosses the boundary. The mass
balance for this system can be expressed as
Mass balance:
min − m out = Δmsystem → mi = m 2 − m1 = ρ 2V − ρ 1V
Substituting, mi = ( ρ 2 − ρ 1 )V = [(7.20 - 1.18) kg/m 3 ](1 m 3 ) = 6.02 kg
V1 = 1 m3
ρ1 =1.18 kg/m3
Therefore, 6.02 kg of mass entered the tank.
Discussion
Tank temperature and pressure do not enter into the calculations.
5-4
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-11
Solution
The ventilating fan of the bathroom of a building runs continuously. The mass of air “vented out” per day is
to be determined.
Assumptions
Flow through the fan is steady.
Properties
The density of air in the building is given to be 1.20 kg/m3.
Analysis
The mass flow rate of air vented out is
m air = ρVair = (1.20 kg/m 3 )(0.030 m 3 /s ) = 0.036 kg/s
Then the mass of air vented out in 24 h becomes
m = m air Δt = (0.036 kg/s)(24 × 3600 s) = 3110 kg
Discussion
Note that more than 3 tons of air is vented out by a bathroom fan in one day.
5-12
Solution
A desktop computer is to be cooled by a fan at a high elevation where the air density is low. The mass flow
rate of air through the fan and the diameter of the casing for a given velocity are to be determined.
Assumptions
Flow through the fan is steady.
Properties
The density of air at a high elevation is given to be 0.7 kg/m3.
Analysis
The mass flow rate of air is
m air = ρVair = (0.7 kg/m 3 )(0.34 m 3 /min ) = 0.238 kg/min = 0.0040 kg/s
If the mean velocity is 110 m/min, the diameter of the casing is
πD
V = AV =
V
4
2
→
D=
4V
=
πV
4(0.34 m 3 /min)
= 0.063 m
π (110 m/min)
Therefore, the diameter of the casing must be at least 6.3 cm to ensure that the mean velocity does not exceed 110 m/min.
Discussion
This problem shows that engineering systems are sized to satisfy given imposed constraints.
5-13
Solution
A smoking lounge that can accommodate 15 smokers is considered. The required minimum flow rate of air
that needs to be supplied to the lounge and the diameter of the duct are to be determined.
Assumptions
Infiltration of air into the smoking lounge is negligible.
Properties
The minimum fresh air requirements for a smoking lounge is given to be 30 L/s per person.
Analysis
The required minimum flow rate of air that needs to be supplied to the lounge is determined directly from
Vair =Vair per person ( No. of persons)
= (30 L/s ⋅ person)(15 persons) = 450 L/s = 0.45 m 3 /s
The volume flow rate of fresh air can be expressed as
V = VA = V (πD 2 / 4 )
Solving for the diameter D and substituting,
4(0.45 m 3 /s)
4V
=
= 0.268 m
D=
πV
π (8 m/s)
Smoking Lounge
15 smokers
30 L/s person
Therefore, the diameter of the fresh air duct should be at least 26.8 cm if the velocity of air is not to exceed 8 m/s.
Discussion
Fresh air requirements in buildings must be taken seriously to avoid health problems.
5-5
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-14
Solution
The minimum fresh air requirements of a residential building is specified to be 0.35 air changes per hour.
The size of the fan that needs to be installed and the diameter of the duct are to be determined.
The volume of the building and the required minimum volume flow rate of fresh air are
Analysis
V room = (2.7 m)(200 m 2 ) = 540 m 3
V = V room × ACH = (540 m 3 )(0.35/h ) = 189 m 3 / h = 189,000 L/h = 3150 L/min
The volume flow rate of fresh air can be expressed as
V = VA = V (πD 2 / 4 )
House
0.35 ACH
Solving for the diameter D and substituting,
D=
4V
=
πV
200 m2
4(189 / 3600 m 3 /s)
= 0.106 m
π (6 m/s)
Therefore, the diameter of the fresh air duct should be at least 10.6 cm if the velocity of air is not to exceed 6 m/s.
Discussion
Fresh air requirements in buildings must be taken seriously to avoid health problems.
5-6
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
Mechanical Energy and Pump Efficiency
5-15C
Solution
We are to discuss mechanical energy and how it differs from thermal energy.
Analysis
Mechanical energy is the form of energy that can be converted to mechanical work completely and
directly by a mechanical device such as a propeller. It differs from thermal energy in that thermal energy cannot be
converted to work directly and completely. The forms of mechanical energy of a fluid stream are kinetic, potential, and
flow energies.
Discussion
It would be nice if we could convert thermal energy completely into work. However, this would violate the
second law of thermodynamics.
5-16C
Solution
We are to define and discuss mechanical efficiency.
Analysis
Mechanical efficiency is defined as the ratio of the mechanical energy output to the mechanical energy
input. A mechanical efficiency of 100% for a hydraulic turbine means that the entire mechanical energy of the fluid is
converted to mechanical (shaft) work.
Discussion
No real fluid machine is 100% efficient, due to frictional losses, etc. – the second law of thermodynamics.
5-17C
Solution
We are to define and discuss pump-motor efficiency.
Analysis
The combined pump-motor efficiency of a pump/motor system is defined as the ratio of the increase in the
mechanical energy of the fluid to the electrical power consumption of the motor,
W pump
E mech,out − E mech,in ΔE mech,fluid
=
=
η pump - motor = η pumpη motor =
W
W
W
elect,in
elect,in
elect,in
The combined pump-motor efficiency cannot be greater than either of the pump or motor efficiency since both pump and
motor efficiencies are less than 1, and the product of two numbers that are less than one is less than either of the numbers.
Discussion
Since many pumps are supplied with an integrated motor, pump-motor efficiency is a useful parameter.
5-18C
Solution
We are to define and discuss turbine, generator, and turbine-generator efficiency.
Analysis
Turbine efficiency, generator efficiency, and combined turbine-generator efficiency are defined as follows:
W shaft,out
Mechanical energy output
=
η turbine =
Mechanical energy extracted from the fluid | ΔE
|
mech,fluid
η generator
Electrical power output W elect,out
=
=
Mechanical power input W shaft,in
η turbine -gen = η turbineη generaor =
Discussion
W elect,out
− E
E mech,in
mech,out
=
W elect,out
| ΔE mech,fluid |
Most turbines are connected directly to a generator, so the combined efficiency is a useful parameter.
5-7
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-19
Solution
A river is flowing at a specified velocity, flow rate, and elevation. The total mechanical energy of the river
water per unit mass, and the power generation potential of the entire river are to be determined.
Assumptions 1 The elevation given is the elevation of the free surface of the river. 2 The velocity given is the average
velocity. 3 The mechanical energy of water at the turbine exit is negligible.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
Noting that the sum of the flow energy and the potential energy is constant for a given fluid body, we can
take the elevation of the entire river water to be the elevation of the free surface, and ignore the flow energy. Then the total
mechanical energy of the river water per unit mass becomes
V2
e mech = pe + ke = gh +
2
3 m/s
River
2
⎛
(3 m/s ) ⎞⎛ 1 kJ/kg ⎞
⎟⎜
= ⎜⎜ (9.81 m/s 2 )(90 m) +
⎟⎝ 1000 m 2 /s 2 ⎟⎠
2
⎠
⎝
90 m
= 0.887 kJ/kg
The power generation potential of the river water is obtained by multiplying the total
mechanical energy by the mass flow rate,
m = ρV = (1000 kg/m 3 )(500 m 3 /s) = 500,000 kg/s
W max = E mech = m e mech = (500,000 kg/s)(0.887 kg/s) = 444,000 kW = 444 MW
Therefore, 444 MW of power can be generated from this river as it discharges into the lake if its power potential can be
recovered completely.
Discussion
Note that the kinetic energy of water is negligible compared to the potential energy, and it can be ignored in
the analysis. Also, the power output of an actual turbine will be less than 444 MW because of losses and inefficiencies.
5-8
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-20
Solution
A hydraulic turbine-generator is generating electricity from the water of a large reservoir. The combined
turbine-generator efficiency and the turbine efficiency are to be determined.
Assumptions
negligible.
1 The elevation of the reservoir remains constant. 2 The mechanical energy of water at the turbine exit is
Analysis
We take the free surface of the reservoir to be point 1 and the turbine exit to be point 2. We also take the
turbine exit as the reference level (z2 = 0), and thus the potential energy at points 1 and 2 are pe1 = gz1 and pe2 = 0. The flow
energy P/ρ at both points is zero since both 1 and 2 are open to the atmosphere (P1 = P2 = Patm). Further, the kinetic energy
at both points is zero (ke1 = ke2 = 0) since the water at point 1 is essentially motionless, and the kinetic energy of water at
turbine exit is assumed to be negligible. The potential energy of water at point 1 is
⎛ 1 kJ/kg ⎞
pe1 = gz1 = (9.81 m/s 2 )(70 m)⎜
⎟ = 0.687 kJ/kg
1
⎝ 1000 m 2 /s 2 ⎠
Then the rate at which the mechanical energy of the fluid is supplied
to the turbine become
ΔE mech,fluid = m (e mech,in − e mech,out ) = m ( pe1 − 0) = m pe1
The combined turbine-generator and the turbine efficiency are
determined from their definitions,
η turbine-gen =
η turbine =
750 kW
70 m
= (1500 kg/s)(0.687 kJ/kg)
= 1031 kW
W elect,out
750 kW
=
= 0.727 or 72.7%
| ΔE mech,fluid | 1031 kW
Generator
Turbine
2
W shaft,out
800 kW
=
= 0.776 or 77.6%
| ΔE mech,fluid | 1031 kW
Therefore, the reservoir supplies 1031 kW of mechanical energy to the turbine, which converts 800 kW of it to shaft work
that drives the generator, which generates 750 kW of electric power.
Discussion
This problem can also be solved by taking point 1 to be at the turbine inlet, and using flow energy instead of
potential energy. It would give the same result since the flow energy at the turbine inlet is equal to the potential energy at
the free surface of the reservoir.
5-9
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-21
Solution
Wind is blowing steadily at a certain velocity. The mechanical energy of air per unit mass, the power
generation potential, and the actual electric power generation are to be determined.
Assumptions 1 The wind is blowing steadily at a constant uniform velocity. 2 The efficiency of the wind turbine is
independent of the wind speed.
Properties
The density of air is given to be ρ = 1.25 kg/m3.
Analysis
Kinetic energy is the only form of mechanical energy the wind possesses, and it can be converted to work
entirely. Therefore, the power potential of the wind is its kinetic energy, which is V2/2 per unit mass, and m V 2 / 2 for a
given mass flow rate:
V 2 (12 m/s ) 2 ⎛ 1 kJ/kg ⎞
e mech = ke =
=
⎟ = 0.072 kJ/kg
⎜
2
2
⎝ 1000 m 2 /s 2 ⎠
m = ρVA = ρV
πD 2
4
= (1.25 kg/m 3 )(12 m/s)
π (50 m) 2
4
= 29,452 kg/s
mech = ( 29 , 452 kg/s )( 0.072 kJ/kg ) = 2121 kW ≅ 2120 kW
Wmax = E mech = me
The actual electric power generation is determined by multiplying the power generation potential by the efficiency,
W elect = η wind turbineW max = (0.30)(2121 kW) = 636 kW
Therefore, 636 kW of actual power can be generated by this wind turbine at the stated conditions.
Wind
Wind
turbine
12 m/s
50 m
Discussion
The power generation of a wind turbine is proportional to the cube of the wind velocity, and thus the power
generation will change strongly with the wind conditions.
5-10
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-22
Solution
The previous problem is reconsidered. The effect of wind velocity and the blade span diameter on wind
power generation as the velocity varies from 5 m/s to 20 m/s in increments of 5 m/s, and the diameter varies from 20 m to
80 m in increments of 20 m is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
D1=20 "m"
D2=40 "m"
D3=60 "m"
D4=80 "m"
Eta=0.30
rho=1.25 "kg/m3"
m1_dot=rho*V*(pi*D1^2/4); W1_Elect=Eta*m1_dot*(V^2/2)/1000 "kW"
m2_dot=rho*V*(pi*D2^2/4); W2_Elect=Eta*m2_dot*(V^2/2)/1000 "kW"
m3_dot=rho*V*(pi*D3^2/4); W3_Elect=Eta*m3_dot*(V^2/2)/1000 "kW"
m4_dot=rho*V*(pi*D4^2/4); W4_Elect=Eta*m4_dot*(V^2/2)/1000 "kW"
D, m
20
V, m/s
5
10
15
20
5
10
15
20
5
10
15
20
5
10
15
20
40
60
80
m, kg/s
1,963
3,927
5,890
7,854
7,854
15,708
23,562
31,416
17,671
35,343
53,014
70,686
31,416
62,832
94,248
125,664
Welect, kW
7
59
199
471
29
236
795
1885
66
530
1789
4241
118
942
3181
7540
8000
D = 80 m
7000
6000
WElect
5000
D = 60 m
4000
3000
D = 40 m
2000
1000
0
4
D = 20 m
6
8
10
12
14
16
18
20
V, m/s
Discussion
Wind turbine power output is obviously nonlinear with respect to both velocity and diameter.
5-11
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-23E
Solution
A differential thermocouple indicates that the temperature of water rises a certain amount as it flows
through a pump at a specified rate. The mechanical efficiency of the pump is to be determined.
Assumptions 1 The pump is adiabatic so that there is no heat transfer with the surroundings, and the temperature rise of
water is completely due to frictional heating. 2 Water is an incompressible substance.
Properties
We take the density of water to be ρ = 62.4 lbm/ft3 and its specific heat to be C = 1.0 Btu/lbm⋅°F.
Analysis
The increase in the temperature of water is due to the conversion of mechanical energy to thermal energy,
and the amount of mechanical energy converted to thermal energy is equal to the increase in the internal energy of water,
m = ρV = (62.4 lbm/ft 3 )(1.5 ft 3/s) = 93.6 lbm/s
ΔT =0.072°F
E mech, loss = ΔU = m cΔT
1 hp
⎞
⎛
= (93.6 lbm/s)(1.0 Btu/lbm ⋅ °F)(0.072°F)⎜
⎟ = 9.53 hp
0.7068
Btu/s
⎠
⎝
The mechanical efficiency of the pump is determined from the general
definition of mechanical efficiency,
η pump = 1 −
E mech,loss
9.53 hp
= 1−
= 0.647 or 64.7%
27 hp
W
Pump
27 hp
mech, in
Discussion
Note that despite the conversion of more than one-third of the mechanical power input into thermal energy,
the temperature of water rises by only a small fraction of a degree. Therefore, the temperature rise of a fluid due to
frictional heating is usually negligible in heat transfer analysis.
5-12
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-24
Solution
Water is pumped from a lake to a storage tank at a specified rate. The overall efficiency of the pump-motor
unit and the pressure difference between the inlet and the exit of the pump are to be determined.
Assumptions 1 The elevations of the tank and the lake remain constant. 2 Frictional losses in the pipes are negligible. 3
The changes in kinetic energy are negligible. 4 The elevation difference across the pump is negligible.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
(a) We take the free surface of the lake to be point 1 and the free surfaces of the storage tank to be point 2.
We also take the lake surface as the reference level (z1 = 0), and thus the potential energy at points 1 and 2 are pe1 = 0 and
pe2 = gz2. The flow energy at both points is zero since both 1 and 2 are open to the atmosphere (P1 = P2 = Patm). Further, the
kinetic energy at both points is zero (ke1 = ke2 = 0) since the water at both locations is essentially stationary. The mass flow
rate of water and its potential energy at point 2 are
m = ρV = (1000 kg/m 3 )(0.070 m 3/s) = 70 kg/s
⎛ 1 kJ/kg ⎞
pe1 = gz1 = (9.81 m/s 2 )(20 m)⎜
⎟ = 0.196 kJ/kg
⎝ 1000 m 2 /s 2 ⎠
Then the rate of increase of the mechanical energy of water becomes
ΔE mech,fluid = m (e mech,out − e mech,in ) = m ( pe 2 − 0) = m pe 2 = (70 kg/s)(0.196 kJ/kg) = 13.7 kW
The overall efficiency of the combined pump-motor unit is determined from its definition,
η pump-motor =
ΔE mech,fluid 13.7 kW
=
= 0.672 or 67.2%
20.4 kW
W elect,in
(b) Now we consider the pump. The change in the mechanical energy of
water as it flows through the pump consists of the change in the flow
energy only since the elevation difference across the pump and the
change in the kinetic energy are negligible. Also, this change must be
equal to the useful mechanical energy supplied by the pump, which is
13.7 kW:
P − P1
ΔE mech,fluid = m (e mech,out − e mech,in ) = m 2
= VΔP
ρ
2
Storage
tank
20 m
Pump
1
Solving for ΔP and substituting,
ΔP =
ΔE mech,fluid
13.7 kJ/s ⎛ 1 kPa ⋅ m 3
⎜
=
0.070 m 3 /s ⎜⎝ 1 kJ
V
⎞
⎟ = 196 kPa
⎟
⎠
Therefore, the pump must boost the pressure of water by 196 kPa in
order to raise its elevation by 20 m.
Discussion
Note that only two-thirds of the electric energy consumed by the pump-motor is converted to the
mechanical energy of water; the remaining one-third is wasted because of the inefficiencies of the pump and the motor.
5-13
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
Bernoulli Equation
5-25C
Solution
We are to define streamwise acceleration and discuss how it differs from normal acceleration.
Analysis
The acceleration of a fluid particle along a streamline is called streamwise acceleration, and it is due to a
change in speed along a streamline. Normal acceleration (or centrifugal acceleration), on the other hand, is the
acceleration of a fluid particle in the direction normal to the streamline, and it is due to a change in direction.
Discussion
In a general fluid flow problem, both streamwise and normal acceleration are present.
5-26C
Solution
We are to express the Bernoulli equation in three different ways.
Analysis
The Bernoulli equation is expressed in three different ways as follows:
P
+
V2
+ gz = constant
2
(a) In terms of energies:
ρ
(b) In terms of pressures:
P+ρ
(c) in terms of heads:
P V2
+
+ z = H = constant
ρg 2 g
V2
+ ρgz = constant
2
Discussion
You could, of course, express it in other ways, but these three are the most useful.
5-27C
Solution
We are to discuss the three major assumptions used in the derivation of the Bernoulli equation.
Analysis
The three major assumptions used in the derivation of the Bernoulli equation are that the flow is steady,
there is negligible frictional effects, and the flow is incompressible.
Discussion
If any one of these assumptions is not valid, the Bernoulli equation should not be used. Unfortunately, many
people use it anyway, leading to errors.
5-28C
Solution
We are to define and discuss static, dynamic, and hydrostatic pressure.
Analysis
Static pressure P is the actual pressure of the fluid. Dynamic pressure ρV 2/2 is the pressure rise when
the fluid in motion is brought to a stop isentropically. Hydrostatic pressure ρgz is not pressure in a real sense since its
value depends on the reference level selected, and it accounts for the effects of fluid weight on pressure. The sum of
static, dynamic, and hydrostatic pressures is constant when flow is steady and incompressible, and when frictional effects
are negligible.
Discussion
The incompressible Bernoulli equation states that the sum of these three pressures is constant along a
streamline; this approximation is valid only for steady and incompressible flow with negligible frictional effects.
5-14
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-29C
Solution
We are to define and discuss pressure head, velocity head, and elevation head.
Analysis
The sum of the static and dynamic pressures is called the stagnation pressure, and it is expressed as
2
Pstag = P + ρV / 2 . The stagnation pressure can be measured by a Pitot tube whose inlet is normal to the flow.
Discussion
Stagnation pressure, as its name implies, is the pressure obtained when a flowing fluid is brought to rest
isentropically, at a so-called stagnation point.
5-30C
Solution
We are to define and discuss pressure head, velocity head, and elevation head.
Analysis
The pressure head P/ρg is the height of a fluid column that produces the static pressure P. The velocity
head V 2/2 is the elevation needed for a fluid to reach the velocity V during frictionless free fall. The elevation head z is
the height of a fluid relative to a reference level.
Discussion
It is often convenient in fluid mechanics to work with head – pressure expressed as an equivalent column
height of fluid.
5-31C
Solution
We are to define hydraulic grade line and compare it to energy grade line.
Analysis
The curve that represents the sum of the static pressure and the elevation heads, P/ρg + z, is called the
hydraulic grade line or HGL. The curve that represents the total head of the fluid, P/ρg + V 2/2g + z, is called the energy
line or EGL. Thus, in comparison, the energy grade line contains an extra kinetic-energy-type term. For stationary bodies
such as reservoirs or lakes, the EL and HGL coincide with the free surface of the liquid.
Discussion
The hydraulic grade line can rise or fall along flow in a pipe or duct as the cross-sectional area increases or
decreases, whereas the energy grade line always decreases unless energy is added to the fluid (like with a pump).
5-32C
Solution
We are to discuss the hydraulic grade line in open-channel flow and at the outlet of a pipe.
Analysis
For open-channel flow, the hydraulic grade line (HGL) coincides with the free surface of the liquid. At
the exit of a pipe discharging to the atmosphere, HGL coincides with the elevation of the pipe outlet.
Discussion
We are assuming incompressible flow, and the pressure at the pipe outlet is atmospheric.
5-33C
Solution
We are to discuss the maximum rise of a jet of water from a tank.
Analysis
With no losses and a 100% efficient nozzle, the water stream could reach to the water level in the tank, or
20 meters. In reality, friction losses in the hose, nozzle inefficiencies, orifice losses, and air drag would prevent attainment
of the maximum theoretical height.
Discussion
In fact, the actual maximum obtainable height is much smaller than this ideal theoretical limit.
5-15
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-34C
Solution
We are to discuss the effect of liquid density on the operation of a siphon.
Analysis
The lower density liquid can go over a higher wall, provided that cavitation pressure is not reached.
Therefore, oil may be able to go over a higher wall than water.
Discussion
However, frictional losses in the flow of oil in a pipe or tube are much greater than those of water since the
viscosity of oil is much greater than that of water. When frictional losses are considered, the water may actually be able to
be siphoned over a higher wall than the oil, depending on the tube diameter and length, etc.
5-35C
Solution
We are to explain how and why a siphon works, and its limitations.
Analysis
Siphoning works because of the elevation and thus pressure difference between the inlet and exit of a tube.
The pressure at the tube exit and at the free surface of a liquid is the atmospheric pressure. When the tube exit is below the
free surface of the liquid, the elevation head difference drives the flow through the tube. At sea level, 1 atm pressure can
support about 10.3 m of cold water (cold water has a low vapor pressure). Therefore, siphoning cold water over a 7 m wall
is theoretically feasible.
Discussion
In actual practice, siphoning is also limited by frictional effects in the tube, and by cavitation.
5-36C
Solution
We are to compare siphoning at sea level and on a mountain.
Analysis
At sea level, a person can theoretically siphon water over a wall as high as 10.3 m. At the top of a high
mountain where the pressure is about half of the atmospheric pressure at sea level, a person can theoretically siphon water
over a wall that is only half as high. An atmospheric pressure of 58.5 kPa is insufficient to support a 8.5 meter high
siphon.
Discussion
In actual practice, siphoning is also limited by frictional effects in the tube, and by cavitation.
5-37C
Solution
We are to analyze the pressure change in a converging duct.
Analysis
As the duct converges to a smaller cross-sectional area, the velocity increases. By Bernoulli’s equation, the
pressure therefore decreases. Thus Manometer A is correct since the pressure on the right side of the manometer is
obviously smaller. According to the Bernoulli approximation, the fluid levels in the manometer are independent of the flow
direction, and reversing the flow direction would have no effect on the manometer levels. Manometer A is still correct if
the flow is reversed.
Discussion
In reality, it is hard for a fluid to expand without the flow separating from the walls. Thus, reverse flow with
such a sharp expansion would not produce as much of a pressure rise as that predicted by the Bernoulli approximation.
5-16
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-38C
Solution
We are to discuss and compare two different types of manometer arrangements in a flow.
Analysis
Arrangement 1 consists of a Pitot probe that measures the stagnation pressure at the pipe centerline, along
with a static pressure tap that measures static pressure at the bottom of the pipe. Arrangement 2 is a Pitot-static probe that
measures both stagnation pressure and static pressure at nearly the same location at the pipe centerline. Because of this,
arrangement 2 is more accurate. However, it turns out that static pressure in a pipe varies with elevation across the pipe
cross section in much the same way as in hydrostatics. Therefore, arrangement 1 is also very accurate, and the elevation
difference between the Pitot probe and the static pressure tap is nearly compensated by the change in hydrostatic pressure.
Since elevation changes are not important in either arrangement, there is no change in our analysis when the water is
replaced by air.
Discussion
Ignoring the effects of gravity, the pressure at the centerline of a turbulent pipe flow is actually somewhat
smaller than that at the wall due to the turbulent eddies in the flow, but this effect is small.
5-39
Solution
A water pipe bursts as a result of freezing, and water shoots up into the air a certain height. The gage
pressure of water in the pipe is to be determined.
Assumptions 1 The flow is steady, incompressible, and irrotational with negligible frictional effects (so that the Bernoulli
equation is applicable). 2 The water pressure in the pipe at the burst section is equal to the water main pressure. 3 Friction
between the water and air is negligible. 4 The irreversibilities that may occur at the burst section of the pipe due to abrupt
expansion are negligible.
Properties
We take the density of water to be 1000 kg/m3.
2
Analysis
This problem involves the conversion of flow, kinetic,
and potential energies to each other without involving any pumps,
turbines, and wasteful components with large frictional losses, and thus
it is suitable for the use of the Bernoulli equation. The water height
will be maximum under the stated assumptions. The velocity inside the
hose is relatively low (V1 ≅ 0) and we take the burst section of the pipe
as the reference level (z1 = 0). At the top of the water trajectory V2 = 0,
and atmospheric pressure pertains. Then the Bernoulli equation
simplifies to
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P1
P
= atm + z2
ρg
ρg
→
P1 − Patm
= z2 →
ρg
34 m
1
Water Pipe
P1,gage
ρg
= z2
Solving for P1,gage and substituting,
⎞
1 kN
⎛ 1 kPa ⎞⎛⎜
⎟ = 334 kPa
P1,gage = ρgz2 = (1000 kg/m 3 )(9.81 m/s 2 )(34 m )⎜
⎟
⎝ 1 kN/m 2 ⎠⎜⎝ 1000 kg ⋅ m/s 2 ⎟⎠
Therefore, the pressure in the main must be at least 334 kPa above the atmospheric pressure.
Discussion
The result obtained by the Bernoulli equation represents a limit, since frictional losses are neglected, and
should be interpreted accordingly. It tells us that the water pressure (gage) cannot possibly be less than 334 kPa (giving us a
lower limit), and in all likelihood, the pressure will be much higher.
5-17
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-40
Solution
The velocity of an aircraft is to be measured by a Pitot-static probe. For a given differential pressure
reading, the velocity of the aircraft is to be determined.
Assumptions 1 The air flow over the aircraft is steady, incompressible,
and irrotational with negligible frictional effects (so that the Bernoulli
equation is applicable). 2 Standard atmospheric conditions exist. 3 The
wind effects are negligible.
Properties
The density of the atmosphere at an elevation of 3000 m is ρ
= 0.909 kg/m3.
Analysis
We take point 1 at the entrance of the tube whose opening is
parallel to flow, and point 2 at the entrance of the tube whose entrance is
normal to flow. Noting that point 2 is a stagnation point and thus V2 = 0 and
z1 = z2, the application of the Bernoulli equation between points 1 and 2
gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
V12 P2 − P1
=
ρg
2g
→
V12 Pstag − P1
=
ρ
2
Solving for V1 and substituting,
V1 =
2( Pstag − P1 )
ρ
=
2(3000 N/m 2 ) ⎛ 1 kg ⋅ m/s 2 ⎞
⎜
⎟ = 81.2 m/s = 292 km/h
⎟
0.909 kg/m 3 ⎜⎝ 1 N
⎠
2
since 1 Pa = 1 N/m and 1 m/s = 3.6 km/h.
Discussion
Note that the velocity of an aircraft can be determined by simply measuring the differential pressure on a
Pitot-static probe.
5-41
Solution
The bottom of a car hits a sharp rock and a small hole develops at the bottom of its gas tank. For a given
height of gasoline, the initial velocity of the gasoline out of the hole is to be determined. Also, the variation of velocity with
time and the effect of the tightness of the lid on flow rate are to be discussed.
Assumptions 1 The flow is steady, incompressible, and irrotational with negligible frictional effects (so that the Bernoulli
equation is applicable). 2 The air space in the tank is at atmospheric pressure. 3 The splashing of the gasoline in the tank
during travel is not considered.
Analysis
This problem involves the conversion of flow, kinetic, and potential energies to each other without
involving any pumps, turbines, and wasteful components with large frictional losses, and thus it is suitable for the use of the
Bernoulli equation. We take point 1 to be at the free surface of gasoline in the tank so that P1 = Patm (open to the
atmosphere) V1 ≅ 0 (the tank is large relative to the outlet), and z1 = 0.3 m and z2 = 0 (we take the reference level at the
hole. Also, P2 = Patm (gasoline discharges into the atmosphere). Then the Bernoulli equation simplifies to
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
z1 =
Gas Tank
V22
2g
1
Solving for V2 and substituting,
30 cm
V2 = 2 gz1 = 2(9.81 m/s 2 )(0.3 m) = 2.43 m/s
Therefore, the gasoline will initially leave the tank with a velocity of 2.43 m/s.
2
V2
The Bernoulli equation applies along a streamline, and streamlines generally do not make sharp turns. The
Discussion
velocity will be less than 2.43 m/s since the hole is probably sharp-edged and it will cause some head loss. As the gasoline
level is reduced, the velocity will decrease since velocity is proportional to the square root of liquid height. If the lid is
tightly closed and no air can replace the lost gasoline volume, the pressure above the gasoline level will be reduced, and the
velocity will be decreased.
5-18
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-42E [Also solved using EES on enclosed DVD]
Solution
The drinking water needs of an office are met by large water bottles with a plastic hose inserted in it. The
minimum filling time of an 8-oz glass is to be determined when the bottle is full and when it is near empty.
Assumptions 1 The flow is steady, incompressible, and irrotational with negligible frictional effects (so that the Bernoulli
equation is applicable). 2 All losses are neglected to obtain the minimum filling time.
Analysis
We take point 1 to be at the free surface of water in the bottle and point 2 at the exit of the tube so that P1 =
P2 = Patm (the bottle is open to the atmosphere and water discharges into the atmosphere), V1 ≅ 0 (the bottle is large relative
to the tube diameter), and z2 = 0 (we take point 2 as the reference level). Then the Bernoulli equation simplifies to
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
z1 =
V22
2g
→
V2 = 2 gz1
Substituting, the discharge velocity of water and the filling time are determined as follows:
(a) Full bottle (z1 = 3.5 ft):
0.25 in
V2 = 2(32.2 ft/s )(3.5 ft) = 15.0 ft/s
2
A = πD 2 / 4 = π (0.25 / 12 ft) 2 / 4 = 3.41 × 10−4 ft 2
V
V
0.00835 ft 3
Δt = =
=
= 1.6 s
AV2 (3.41× 10− 4 ft 2 )(15 ft/s )
V
1.5 ft
1
(b) Empty bottle (z1 = 2 ft):
V2 = 2(32.2 ft/s 2 )(2 ft) = 11.3 ft/s
2 ft
3
V
V
0.00835 ft
Δt = =
=
= 2.2 s
AV2 (3.41× 10 − 4 ft 2 )(11.3 ft/s )
V
2
Discussion
The siphoning time is determined assuming frictionless flow, and
thus this is the minimum time required. In reality, the time will be longer because of
friction between water and the tube surface.
5-43
Solution
The static and stagnation pressures in a horizontal pipe are measured. The velocity at the center of the pipe
is to be determined.
Assumptions The flow is steady, incompressible, and irrotational with negligible frictional effects in the short distance
between the two pressure measurement locations (so that the Bernoulli equation is applicable).
Analysis
We take points 1 and 2 along the centerline of the pipe, with point 1 directly under the piezometer and
point 2 at the entrance of the Pitot-static probe (the stagnation point).
This is a steady flow with straight and parallel streamlines, and thus the
static pressure at any point is equal to the hydrostatic pressure at that
point. Noting that point 2 is a stagnation point and thus V2 = 0 and z1 =
35 cm
20 cm
z2, the application of the Bernoulli equation between points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
V12 P2 − P1
=
ρg
2g
Water
1
2
V
Substituting the P1 and P2 expressions give
V12 P2 − P1 ρg (hpitot + R ) − ρg (hpiezo + R ) ρg (hpitot − hpiezo )
=
=
=
= hpitot − hpiezo
2g
ρg
ρg
ρg
Solving for V1 and substituting,
V1 = 2 g (hpitot − hpiezo ) = 2(9.81 m/s 2 )[(0.35 − 0.20) m] = 1.72 m/s
Discussion
Note that to determine the flow velocity, all we need is to measure the height of the excess fluid column in
the Pitot-static probe.
5-19
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-44
Solution
A water tank of diameter Do and height H open to the atmosphere is initially filled with water. An orifice of
diameter D with a smooth entrance (no losses) at the bottom drains to the atmosphere. Relations are to be developed for the
time required for the tank to empty completely and half-way.
Assumptions 1 The orifice has a smooth entrance, and thus the frictional losses are negligible. 2 The flow is steady,
incompressible, and irrotational with negligible frictional effects (so that the Bernoulli equation is applicable).
Analysis
We take point 1 at the free surface of the tank, and point 2 at the exit of orifice. We take the reference level
at the orifice (z2 = 0), and take the positive direction of z to be upwards. Noting that the fluid at both points is open to the
atmosphere (and thus P1 = P2 = Patm) and that the fluid velocity at the free surface is very low (V1 ≅ 0), the Bernoulli
equation between these two points simplifies to
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
z1 =
V22
2g
→
V2 = 2 gz1
For generality, we express the water height in the tank at any time t by z, and the discharge velocity by V2 = 2 gz . Note
that water surface in the tank moves down as the tank drains, and thus z is a variable whose value changes from H at the
beginning to 0 when the tank is emptied completely.
We denote the diameter of the orifice by D, and the diameter of the tank by Do. The flow rate of water from the
tank is obtained by multiplying the discharge velocity by the orifice cross-sectional area,
πD 2
V = AorificeV 2 =
2 gz
1 Tank
Water
4
Then the amount of water that flows through the orifice during a differential time
interval dt is
H
πD 2
D0
dV =Vdt =
2 gz dt
(1)
4
D
which, from conservation of mass, must be equal to the decrease in the volume of
water in the tank,
πD 2
2
(2)
dV = Atank (−dz ) = − 0 dz
4
where dz is the change in the water level in the tank during dt. (Note that dz is a negative quantity since the positive
direction of z is upwards. Therefore, we used –dz to get a positive quantity for the amount of water discharged). Setting
Eqs. (1) and (2) equal to each other and rearranging,
πD 2
D2
D02
1
πD 2
−1
2 gz dt = − 0 dz
→
dt = − 02
dz = −
z 2 dz
2
4
4
2 gz
D
D 2g
The last relation can be integrated easily since the variables are separated. Letting tf be the discharge time and integrating it
from t = 0 when z = zi = H to t = tf when z = zf gives
∫
tf
dt = −
t =0
D02
D2 2g
∫
zf
z −1 / 2 dz →
z = z1
tf = -
1
D02
z2
D2 2 g
1
2
zf
=
(
2g
2 D02
D2
z1
)
zi − z f =
D02
D2
⎛ 2z
2 z f ⎞⎟
i
⎜
−
⎜ g
g ⎟
⎝
⎠
Then the discharging time for the two cases becomes as follows:
(a) The tank empties halfway:
zi = H and zf = H/2:
tf =
D02
D2
(b) The tank empties completely:
zi = H and zf = 0:
tf =
D02
D2
⎛ 2H
H ⎞⎟
⎜
−
⎜ g
g ⎟⎠
⎝
2H
g
Discussion
Note that the discharging time is inversely proportional to the square of the orifice diameter. Therefore, the
discharging time can be reduced to one-fourth by doubling the diameter of the orifice.
5-20
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-45
Solution
Water discharges to the atmosphere from the orifice at the bottom of a pressurized tank. Assuming
frictionless flow, the discharge rate of water from the tank is to be determined.
1
Assumptions 1 The orifice has a smooth entrance, and thus the frictional losses are
Air, 300 kPa
negligible. 2 The flow is steady, incompressible, and irrotational with negligible frictional
effects (so that the Bernoulli equation is applicable).
Properties
We take the density of water to be 1000 kg/m3.
Analysis
We take point 1 at the free surface of the tank, and point 2 at the exit of
orifice, which is also taken to be the reference level (z2 = 0). Noting that the fluid velocity
at the free surface is very low (V1 ≅ 0) and water discharges into the atmosphere (and
thus P2 = Patm), the Bernoulli equation simplifies to
P1 V12
P V2
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
Water
Tank
3m
2
10 cm
V22 P1 − P2
=
+ z1
2g
ρg
Solving for V2 and substituting, the discharge velocity is determined to
V2 =
2( P1 − P2 )
ρ
+ 2 gz1 =
2(300 − 100) kPa ⎛ 1000 N/m 2
⎜
1000 kg/m 3 ⎜⎝ 1 kPa
⎞⎛ 1 kg ⋅ m/s 2
⎟⎜
⎟⎜
1N
⎠⎝
⎞
⎟ + 2(9.81 m/s 2 )(3 m)
⎟
⎠
= 21.4 m/s
Then the initial rate of discharge of water becomes
π (0.10 m)
πD
V = AorificeV 2 =
V2 =
(21.4 m/s) = 0.168 m 3 /s
4
4
2
2
Discussion
Note that this is the maximum flow rate since the frictional effects are ignored. Also, the velocity and the
flow rate will decrease as the water level in the tank decreases.
5-21
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-46
Solution
The previous problem is reconsidered. The effect of water height in the tank on the discharge velocity as the
water height varies from 0 to 5 m in increments of 0.5 m is to be investigated.
The EES Equations window is printed below, followed by the tabulated and plotted results.
Analysis
g=9.81 "m/s2"
rho=1000 "kg/m3"
d=0.10 "m"
P1=300 "kPa"
P_atm=100 "kPa"
V=SQRT(2*(P1-P_atm)*1000/rho+2*g*h)
Ac=pi*D^2/4
V_dot=Ac*V
22.5
22
V, m/s
0.00
0.50
1.00
1.50
2.00
2.50
3.00
3.50
4.00
4.50
5.00
20.0
20.2
20.5
20.7
21.0
21.2
21.4
21.6
21.9
22.1
22.3
Discussion
V , m3/s
0.157
0.159
0.161
0.163
0.165
0.166
0.168
0.170
0.172
0.174
0.175
21.5
V, m/s
h, m
21
20.5
20
0
1
2
3
4
5
h, m
Velocity appears to change nearly linearly with h in this range of data, but the relationship is not linear.
5-22
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-47E
Solution
A siphon pumps water from a large reservoir to a lower tank which is initially empty. Water leaves the tank
through an orifice. The height the water will rise in the tank at equilibrium is to be determined.
Assumptions 1 The flow is steady, incompressible, and irrotational
with negligible frictional effects (so that the Bernoulli equation is
applicable). 2 Both the tank and the reservoir are open to the
atmosphere. 3 The water level of the reservoir remains constant.
Analysis
We take the reference level to be at the bottom of the
tank, and the water height in the tank at any time to be h. We take point
1 to be at the free surface of reservoir, point 2 at the exit of the siphon,
which is placed at the bottom of the tank, and point 3 at the free surface
of the tank, and point 4 at the exit of the orifice at the bottom of the
tank. Then z1 = 20 ft, z2 = z4 = 0, z3 = h, P1 = P3 = P4 = Patm (the
reservoir is open to the atmosphere and water discharges into the
atmosphere) P2 = Patm+ρgh (the hydrostatic pressure at the bottom of
the tank where the siphon discharges), and V1 ≅ V3 ≅ 0 (the free
surfaces of reservoir and the tank are large relative to the tube
diameter). Then the Bernoulli equation between 1-2 and 3-4 simplifies
to
P1 V12
P V2
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P3 V32
P V2
+
+ z3 = 4 + 4 + z 4
ρg 2 g
ρg 2 g
→
Patm
P + ρgh V22
+ z1 = atm
+
2g
ρg
ρg
h=
V42
2g
→
1
2 in
Reservoir
15 ft
3
h
Water
Tank
2
4
→ V2 = 2 gz1 − 2 gh = 2 g ( z1 − h )
V4 = 2 gh
Noting that the diameters of the tube and the orifice are the same, the flow rates of water into and out of the tank will be the
same when the water velocities in the tube and the orifice are equal since
V2 = V4
→
AV2 = AV4 → V2 = V4
Setting the two velocities equal to each other gives
V2 = V4 →
2 g ( z1 − h ) = 2 gh
→
z1 − h = h
→ h=
z1 15 ft
=
= 7.5 ft
2
2
Therefore, the water level in the tank will stabilize when the water level rises to
7.5 ft.
Discussion
This result is obtained assuming negligible friction. The result would be somewhat different if the friction in
the pipe and orifice were considered.
5-23
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-48
Solution
Water enters an empty tank steadily at a specified rate. An orifice at the bottom allows water to escape.
The maximum water level in the tank is to be determined, and a relation for water height z as a function of time is to be
obtained.
Assumptions 1 The orifice has a smooth entrance, and thus the frictional losses are negligible. 2 The flow through the
orifice is steady, incompressible, and irrotational with negligible frictional effects (so that the Bernoulli equation is
applicable).
Analysis
(a) We take point 1 at the free surface of the tank, and point 2 at the exit of orifice. We take the reference
level at the orifice (z2 = 0), and take the positive direction of z to be upwards. Noting that the fluid at both points is open to
the atmosphere (and thus P1 = P2 = Patm) and that the fluid velocity at the free surface is very low (V1 ≅ 0) (it becomes zero
when the water in the tank reaches its maximum level), the Bernoulli equation between these two points simplifies to
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
z1 =
V22
2g
→
m
V2 = 2 gz1
1
Then the mass flow rate through the orifice for a water height of z becomes
m out
πD0
= ρVout = ρAorificeV 2 = ρ
4
2
2 gz
1
→ z=
2g
⎛ 4m out
⎜
⎜ ρπD 2
0
⎝
⎞
⎟
⎟
⎠
Water Tank
2
Setting z = hmax and m out = m in (the incoming flow rate) gives the desired relation for the
maximum height the water will reach in the tank,
DT
z
2
D0
2
D0
⎛ 4m in ⎞
⎟
⎜
⎜ ρπD 2 ⎟
0 ⎠
⎝
(b) The amount of water that flows through the orifice and the increase in the amount of water in the tank during a
differential time interval dt are
πD02
dm out = m out dt = ρ
2 gz dt
4
πDT2
dm tank = ρAtank dz = ρ
dz
4
The amount of water that enters the tank during dt is dmin = m in dt (Recall that m in = constant). Substituting them into the
hmax =
1
2g
conservation of mass relation dm tank = dm in − dm out gives
dm tank = m in dt − m out dt
→
ρ
⎛
πD02
dz = ⎜ m in − ρ
⎜
4
4
⎝
πDT2
⎞
2 gz ⎟dt
⎟
⎠
Separating the variables, and integrating it from z = 0 at t = 0 to z = z at time t = t gives
1
4
ρπDT2 dz
m in − 14 ρπD02 2 gz
= dt
→
∫
z
z =0
1
4
ρπDT2 dz
m in − 14 ρπD02 2 gz
∫
t
= dt = t
t =0
Performing the integration, the desired relation between the water height z and time t is obtained to be
1
2
2
1
⎛
⎜ 1 ρπD 2 2 gz − m ln min − 4 ρπD0 2 gz
0
in
4
m in
2 g ) 2 ⎜⎝
ρπDT2
( 14 ρπD02
⎞
⎟=t
⎟
⎠
Discussion
Note that this relation is implicit in z, and thus we can’t obtain a relation in the form z = f(t). Substituting a z
value in the left side gives the time it takes for the fluid level in the tank to reach that level. Equation solvers such as EES
can easily solve implicit equations like this.
5-24
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-49E
Solution
Water flows through a horizontal pipe that consists of two sections at a specified rate. The differential
height of a mercury manometer placed between the two pipe sections is to be determined.
Assumptions 1The flow through the pipe is steady, incompressible, and irrotational with negligible frictional effects (so
that the Bernoulli equation is applicable). 2 The losses in the reducing section are negligible.
The densities of mercury and water are ρHg = 847 lbm/ft3 and ρw = 62.4 lbm/ft3.
Properties
Analysis
We take points 1 and 2 along the centerline of the pipe over the two tubes of the manometer. Noting that z1
= z2, the Bernoulli equation between points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P1 − P2 =
ρ w (V22 − V12 )
2
(1)
We let the differential height of the mercury manometer be h and the distance between the centerline and the mercury level
in the tube where mercury is raised be s. Then the pressure difference P2 – P1 can also be expressed as
P1 + ρ w g ( s + h) = P2 + ρ w gs + ρ Hg gh
→
P1 − P2 = ( ρ Hg − ρ w ) gh
h=
ρ w (V 22 − V12 )
V 22 − V12
=
2 g ( ρ Hg − ρ w ) 2 g ( ρ Hg / ρ w − 1)
(2)
Combining Eqs. (1) and (2) and solving for h,
ρ w (V 22 − V12 )
2
= ( ρ Hg − ρ w ) gh
→
Calculating the velocities and substituting,
V1 =
V2 =
⎛ 0.13368 ft 3
1 gal/s
V
V
⎜
=
=
A1 πD12 / 4 π (4/12 ft) 2 / 4 ⎜⎝
1 gal
⎞
⎟ = 1.53 ft/s
⎟
⎠
⎛ 0.13368 ft 3
1 gal/s
V
V
⎜
=
=
2
2
A2 πD 2 / 4 π (2/12 ft) / 4 ⎜⎝
1 gal
⎞
⎟ = 6.13 ft/s
⎟
⎠
4 in
1
2
2 in
s
h
h=
(6.13 ft/s) − (1.53 ft/s)
2
2
2(32.2 ft/s 2 )(847 / 62.4 − 1)
= 0.0435 ft = 0.52 in
Therefore, the differential height of the mercury column will be 0.52 in.
Discussion
In reality, there are frictional losses in the pipe, and the pressure at location 2 will actually be smaller than
that estimated here, and therefore h will be larger than that calculated here.
5-25
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-50
Solution
An airplane is flying at a certain altitude at a given speed. The pressure on the stagnation point on the nose
of the plane is to be determined, and the approach to be used at high velocities is to be discussed.
Assumptions 1 The air flow over the aircraft is steady, incompressible, and irrotational with negligible frictional effects
(so that the Bernoulli equation is applicable). 2 Standard atmospheric conditions exist. 3 The wind effects are negligible.
Properties
The density of the atmospheric air at an elevation of 12,000 m is ρ = 0.312 kg/m3.
Analysis
We take point 1 well ahead of the plane at the level of the nose, and point 2 at the nose where the flow
comes to a stop. Noting that point 2 is a stagnation point and thus V2 = 0 and z1 = z2, the application of the Bernoulli
equation between points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
V12 P2 − P1
=
ρg
2g
V12 Pstag − Patm Pstag, gage
=
=
ρ
ρ
2
→
Solving for Pstag, gage and substituting,
Pstag, gage =
ρV12
2
=
⎞
(0.312 kg/m3 )(200 / 3.6 m/s)2 ⎛ 1 N
⎜
⎟ = 481 N/m 2 = 481 Pa
2⎟
⎜
2
⋅
1
kg
m/s
⎝
⎠
since 1 Pa = 1 N/m2 and 1 m/s = 3.6 km/h.
Altitude
12,000 m
2
1
200 km/h
Discussion
A flight velocity of 1050 km/h = 292 m/s corresponds to a Mach number much greater than 0.3 (the speed
of sound is about 340 m/s at room conditions, and lower at higher altitudes, and thus a Mach number of 292/340 = 0.86).
Therefore, the flow can no longer be assumed to be incompressible, and the Bernoulli equation given above cannot be used.
This problem can be solved using the modified Bernoulli equation that accounts for the effects of compressibility, assuming
isentropic flow.
5-26
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-51
Solution
A Pitot-static probe is inserted into the duct of an air heating system parallel to flow, and the differential
height of the water column is measured. The flow velocity and the pressure rise at the tip of the Pitot-static probe are to be
determined.
Assumptions 1 The flow through the duct is steady, incompressible, and irrotational with negligible frictional effects (so
that the Bernoulli equation is applicable). 2 Air is an ideal gas.
Properties
We take the density of water to be ρ = 1000 kg/m3. The gas constant of air is R = 0.287 kPa⋅m3/kg⋅K.
Analysis
We take point 1 on the side of the probe where the entrance is parallel to flow and is connected to the static
arm of the Pitot-static probe, and point 2 at the tip of the probe where the entrance is normal to flow and is connected to the
dynamic arm of the Pitot-static probe. Noting that point 2 is a stagnation point and thus V2 = 0 and z1 = z2, the application
of the Bernoulli equation between points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P1 V12 P2
+
=
ρg 2 g ρg
→
V =
2( P2 − P1 )
ρ air
where the pressure rise at the tip of the Pitot-static probe is
⎛
1N
P2 − P1 = ρ w gh = (1000 kg/m 3 )(9.81 m/s 2 )(0.024 m)⎜⎜
2
⎝ 1 kg ⋅ m/s
⎞
⎟
⎟
⎠
Air
2
V
1
= 235 N/m 2 = 235 Pa
Also,
ρ air =
P
98 kPa
=
= 1.074 kg/m 3
RT (0.287 kPa ⋅ m 3 /kg ⋅ K )(45 + 273 K )
h=2.4 cm
Substituting,
V1 =
2(235 N/m 2 ) ⎛⎜ 1 kg ⋅ m/s 2
1N
1.074 kg/m 3 ⎜⎝
⎞
⎟ = 20.9 m/s
⎟
⎠
Note that the flow velocity in a pipe or duct can be measured easily by a Pitot-static probe by inserting the
Discussion
probe into the pipe or duct parallel to flow, and reading the differential pressure height. Also note that this is the velocity at
the location of the tube. Several readings at several locations in a cross-section may be required to determine the mean flow
velocity.
5-27
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-52
Solution
The water in an above the ground swimming pool is to be emptied by unplugging the orifice of a horizontal
pipe attached to the bottom of the pool. The maximum discharge rate of water is to be determined.
Assumptions 1 The orifice has a smooth entrance, and all frictional losses are negligible. 2 The flow is steady,
incompressible, and irrotational with negligible frictional effects (so that the Bernoulli equation is applicable).
Analysis
We take point 1 at the free surface of the pool, and point 2 at the exit of pipe. We take the reference level at
the pipe exit (z2 = 0). Noting that the fluid at both points is open to the atmosphere (and thus P1 = P2 = Patm) and that the
fluid velocity at the free surface is very low (V1 ≅ 0), the Bernoulli equation between these two points simplifies to
P1 V12
P V2
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
z1 =
V22
2g
→
V2 = 2 gz1
The maximum discharge rate occurs when the water height in the pool is a maximum, which is the case at the beginning
and thus z1 = h. Substituting, the maximum flow velocity and discharge rate become
V 2,max = 2 gh = 2(9.81 m/s 2 )(2 m) = 6.26 m/s
π (0.03 m)
πD
Vmax = ApipeV 2, max =
V 2, max =
(6.26 m/s) = 0.00443 m 3 /s = 4.43 L/s
4
4
2
2
1
Swimming pool
2m
3 cm
10 m
2
m
25 m
Discussion
The result above is obtained by disregarding all frictional effects. The actual flow rate will be less because
of frictional effects during flow and the resulting pressure drop. Also, the flow rate will gradually decrease as the water
level in the pipe decreases.
5-28
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-53
Solution
The water in an above the ground swimming pool is to be emptied by unplugging the orifice of a horizontal
pipe attached to the bottom of the pool. The time it will take to empty the tank is to be determined.
Assumptions 1 The orifice has a smooth entrance, and all frictional losses are negligible. 2 The flow is steady,
incompressible, and irrotational with negligible frictional effects (so that the Bernoulli equation is applicable).
Analysis
We take point 1 at the free surface of water in the pool, and point 2 at the exit of pipe. We take the reference
level at the pipe exit (z2 = 0). Noting that the fluid at both points is open to the atmosphere (and thus P1 = P2 = Patm) and that
the fluid velocity at the free surface is very low (V1 ≅ 0), the Bernoulli equation between these two points simplifies to
P1 V12
P V2
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
z1 =
V22
2g
→
V2 = 2 gz1
For generality, we express the water height in the pool at any time t by z, and the discharge velocity by V2 = 2 gz . Note
that water surface in the pool moves down as the pool drains, and thus z is a variable whose value changes from h at the
beginning to 0 when the pool is emptied completely.
We denote the diameter of the orifice by D, and the diameter of the pool by Do. The flow rate of water from the pool is
obtained by multiplying the discharge velocity by the orifice cross-sectional area,
πD 2
V = AorificeV 2 =
2 gz
4
Then the amount of water that flows through the orifice during a differential time interval dt is
πD 2
dV = Vdt =
2 gz dt
(1)
4
which, from conservation of mass, must be equal to the decrease in the volume of water in the pool,
πD 2
(2)
dV = Atank (−dz ) = − 0 dz
4
where dz is the change in the water level in the pool during dt. (Note that dz is a negative quantity since the positive
direction of z is upwards. Therefore, we used –dz to get a positive quantity for the amount of water discharged). Setting
Eqs. (1) and (2) equal to each other and rearranging,
πD 2
D2
D02
1
πD 2
−1
2 gz dt = − 0 dz
dt = − 02
dz = −
z 2 dz
→
4
4
2 gz
D
D 2 2g
The last relation can be integrated easily since the variables are separated. Letting tf be the discharge time and integrating it
from t = 0 when z = h to t = tf when z = 0 (completely drained pool) gives
∫
tf
dt = −
t =0
D02
D
2
2g ∫
0
z
−1 / 2
z = z1
dz →
tf =-
D02
D
2
2g
1
0
z2
1
2
=
2 D02
D
z1
Substituting, the draining time of the pool will be
( 10 m) 2
2( 2 m)
tf =
= 70,950 s = 19.7 h
2
( 0.03 m ) 9.81 m/s 2
2
2g
h=
D02
D2
2h
g
1
Swimming pool
2m
This is the minimum discharging time
Discussion
since it is obtained by neglecting all friction; the
actual discharging time will be longer. Note that the
discharging time is inversely proportional to the
square of the orifice diameter. Therefore, the
discharging time can be reduced to one-fourth by
doubling the diameter of the orifice.
D0= 10 m
D=3 cm
2
m
25 m
5-29
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-54
Solution
The previous problem is reconsidered. The effect of the discharge pipe diameter on the time required to
empty the pool completely as the diameter varies from 1 to 10 cm in increments of 1 cm is to be investigated.
The EES Equations window is printed below, followed by the tabulated and plotted results.
Analysis
g=9.81 "m/s2"
rho=1000 "kg/m3"
h=2 "m"
D=d_pipe/100 "m"
D_pool=10 "m"
V_initial=SQRT(2*g*h) "m/s"
Ac=pi*D^2/4
V_dot=Ac*V_initial*1000 "m3/s"
t=(D_pool/D)^2*SQRT(2*h/g)/3600
"hour"
Discussion
Discharge time
t, h
177.4
44.3
19.7
11.1
7.1
4.9
3.6
2.8
2.2
1.8
160
140
120
t, hour
Pipe diameter
D, m
1
2
3
4
5
6
7
8
9
10
180
100
80
60
40
20
0
1
2
3
4
5
6
7
8
9
10
D, cm
As you can see from the plot, the discharge time is drastically reduced by increasing the pipe diameter.
5-30
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-55
Solution
Air flows upward at a specified rate through an inclined pipe whose diameter is reduced through a reducer.
The differential height between fluid levels of the two arms of a water manometer attached across the reducer is to be
determined.
Assumptions 1 The flow through the duct is steady, incompressible and irrotational with negligible frictional effects (so
that the Bernoulli equation is applicable). 2 Air is an ideal gas. 3 The effect of air column on the pressure change is
negligible because of its low density. 4 The air flow is parallel to the entrance of each arm of the manometer, and thus no
dynamic effects are involved.
Properties
We take the density of water to be ρ = 1000 kg/m3. The gas constant of air is R = 0.287 kPa⋅m3/kg⋅K.
Analysis
We take points 1 and 2 at the lower and upper connection points, respectively, of the two arms of the
manometer, and take the lower connection point as the reference level. Noting that the effect of elevation on the pressure
change of a gas is negligible, the application of the Bernoulli equation between points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
→
P1 − P2 = ρ air
V 22 − V12
2
2
Air 1
P
110 kPa
=
= 1.19 kg/m 3
3
RT (0.287 kPa ⋅ m /kg ⋅ K )(50 + 273 K )
0.045 m3/s
V
V
=
=
= 15.9 m/s
V1 =
A1 πD12 / 4 π (0.06 m)2 / 4
h
0.045 m 3 /s
V
V
=
=
= 35.8 m/s
V2 =
A2 πD 22 / 4 π (0.04 m) 2 / 4
Substituting,
⎞
(35.8 m/s) 2 − (15.9 m/s) 2 ⎛⎜
1N
⎟ = 612 N/m 2 = 612 Pa The differential height of
P1 − P2 = (1.19 kg/m 3 )
2
⎜
⎟
2
⋅
1
kg
m/s
⎝
⎠
water in the manometer corresponding to this pressure change is determined from ΔP = ρ water gh to be
where
ρ air =
h=
⎛ 1 kg ⋅ m/s 2
P1 − P2
612 N/m 2
⎜
=
3
2 ⎜
ρ water g (1000 kg/m )(9.81 m/s ) ⎝ 1 N
⎞
⎟ = 0.0624 m = 6.24 cm
⎟
⎠
When the effect of air column on pressure change is considered, the pressure change becomes
ρ (V 2 − V12 )
P1 − P2 = air 2
+ ρ air g ( z 2 − z1 )
2
⎞
⎡ (35.8 m/s) 2 − (15.9 m/s) 2
⎤⎛
1N
⎟
= (1.19 kg/m 3 ) ⎢
+ (9.81 m/s 2 )(0.2 m)⎥⎜
2
⎟
⎜
2
⎣⎢
⎦⎥⎝ 1 kg ⋅ m/s ⎠
Discussion
= (612 + 2) N/m 2 = 614 N/m 2 = 614 Pa
This difference between the two results (612 and 614 Pa) is less than 1%. Therefore, the effect of air column on pressure
change is, indeed, negligible as assumed. In other words, the pressure change of air in the duct is almost entirely due to
velocity change, and the effect of elevation change is negligible. Also, if we were to account for the Δz of air flow, then it
would be more proper to account for the Δz of air in the manometer by using ρwater - ρair instead of ρwater when calculating h.
The additional air column in the manometer tends to cancel out the change in pressure due to the elevation difference in the
flow in this case.
5-31
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-56E
Solution
Air is flowing through a venturi meter with known diameters and measured pressures. A relation for the
flow rate is to be obtained, and its numerical value is to be determined.
Assumptions 1The flow through the venturi is steady, incompressible, and irrotational with negligible frictional effects
(so that the Bernoulli equation is applicable). 2 The effect of air column on the pressure change is negligible because of its
low density, and thus the pressure can be assumed to be uniform at a given cross-section of the venturi meter (independent
of elevation change). 3 The flow is horizontal (this assumption is usually unnecessary for gas flow.).
The density of air is given to be ρ = 0.075 lbm/ft3.
Properties
Analysis
We take point 1 at the main flow section and point 2 at the throat along the centerline of the venturi meter.
Noting that z1 = z2, the application of the Bernoulli equation between points 1 and 2 gives
P1 V12
P V2
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
→
P1 − P2 = ρ
V 22 − V12
2
(1)
The flow is assumed to be incompressible and thus the density is constant. Then the conservation of mass relation for this
single stream steady flow device can be expressed as
V1 = V2 = V
A1V1 = A2V 2 = V
→
→ V1 =
V
A1
and
V2 =
V
(2)
A2
Substituting into Eq. (1),
(V / A2 ) 2 − (V / A1 ) 2 ρV 2
P1 − P2 = ρ
=
2
2 A22
Solving for V gives the desired relation for the flow rate,
V = A2
2( P1 − P2 )
12.2 psia
⎛ A22 ⎞
⎟
⎜1 −
⎜ A2 ⎟
1
⎠
⎝
Air
11.8 psia
2
1
2.6 in
1.8 in
(3)
ρ [1 − ( A2 / A1 ) 2 ]
The flow rate for the given case can be determined by substituting the given values into this relation to be
πD 2
V =
4
2( P1 − P2 )
2
ρ [1 − ( D 2 / D1 ) ]
4
=
π (1.8 / 12 ft) 2
4
⎛ 144 lbf/ft 2
⎜
(0.075 lbm/ft 3 )[1 - (1.8/2.6) 4 ] ⎜⎝ 1 psi
2(12.2 − 11.8) psi
⎞⎛ 32.2 lbm ⋅ ft/s 2
⎟⎜
⎟⎜
1 lbf
⎠⎝
⎞
⎟
⎟
⎠
= 4.48 ft 3 /s
Venturi meters are commonly used as flow meters to measure the flow rate of gases and liquids by simply
Discussion
measuring the pressure difference P1 - P2 by a manometer or pressure transducers. The actual flow rate will be less than the
value obtained from Eq. (3) because of the friction losses along the wall surfaces in actual flow. But this difference can be
as little as 1% in a well-designed venturi meter. The effects of deviation from the idealized Bernoulli flow can be accounted
for by expressing Eq. (3) as
V = C c A2
2( P1 − P2 )
ρ [1 − ( A2 / A1 ) 2 ]
where Cc is the venturi discharge coefficient whose value is less than 1 (it is as large as 0.99 for well-designed venturi
meters in certain ranges of flow). For Re > 105, the value of venturi discharge coefficient is usually greater than 0.96.
5-32
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-57
Solution
The gage pressure in the water mains of a city at a particular location is given. It is to be determined if this
main can serve water to neighborhoods that are at a given elevation relative to this location.
Assumptions
Water is incompressible and thus its density is constant.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
Noting that the gage pressure at a dept of h in a fluid is given by Pgage = ρ water gh , the height of a fluid
column corresponding to a gage pressure of 400 kPa is determined to be
h=
Pgage
ρ water g
=
⎛ 1 kg ⋅ m/s 2
⎜
1N
(1000 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
400,000 N/m 2
⎞
⎟ = 40.8 m
⎟
⎠
Water Main,
400 kPa
which is less than 50 m. Therefore, this main cannot serve water to
neighborhoods that are 50 m above this location.
Discussion
Note that h must be much greater than 50 m for water to have enough pressure to serve the water needs of
the neighborhood.
5-33
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-58
Solution
A hand-held bicycle pump with a liquid reservoir is used as an atomizer by forcing air at a high velocity
through a small hole. The minimum speed that the piston must be moved in the cylinder to initiate the atomizing effect is to
be determined.
Assumptions 1The flows of air and water are steady, incompressible, and irrotational with negligible frictional effects (so
that the Bernoulli equation is applicable). 2 Air is an ideal gas. 3 The liquid reservoir is open to the atmosphere. 4 The
device is held horizontal. 5 The water velocity through the tube is low.
Properties
We take the density of water to be ρ = 1000 kg/m3. The
gas constant of air is R = 0.287 kPa⋅m3/kg⋅K.
Air
2
1
3
Analysis
We take point 1 at the exit of the hole, point 2 in air far
from the hole on a horizontal line, point 3 at the exit of the tube in air
stream (so that points 1 and 3 coincide), and point 4 at the free surface
of the liquid in the reservoir (P2 = P4 = Patm and P1 = P3). We also take
the level of the hole to be the reference level (so that z1 = z2 = z3 =0 and
z4 = -h). Noting that V2 ≅ V3 ≅ V4 ≅ 0, the Bernoulli equation for the air
and water streams becomes
Water (3-4):
Air (1-2):
P3 V 32
P V2
+
+ z3 = 4 + 4 + z4
ρg 2 g
ρg 2 g
P V2
P1 V12
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
→
→
P1 Patm
=
+ (−h ) →
ρg
ρg
P1 V12 Patm
+
=
ρg 2 g
ρg
→ V1 =
Liquid
rising
4
P1 − Patm = − ρ water gh
2( Patm − P1 )
ρ air
(1)
(2)
where
ρ air =
95 kPa
P
=
= 1.13 kg/m 3
RT (0.287 kPa ⋅ m 3 /kg ⋅ K )(20 + 273 K )
Combining Eqs. (1) and (2) and substituting the numerical values,
V1 =
2( Patm − P1 )
ρ air
=
2 ρ water gh
ρ air
=
2(1000 kg/m 3 )(9.81 m/s 2 )(0.1 m )
1.13 kg/m 3
= 41.7 m/s
Taking the flow of air to be steady and incompressible, the conservation of mass for air can be expressed as
2
πD hole
A
/4
Vpiston =Vhole → V piston Apiston = V hole Ahole → V piston = hole V hole =
V1
2
Apiston
πD piston / 4
Simplifying and substituting, the piston velocity is determined to be
V piston
⎛ D
= ⎜ hole
⎜ D piston
⎝
2
2
⎞
⎟ V1 = ⎛⎜ 0.3 cm ⎞⎟ (41.7 m/s) = 0.15 m/s
⎟
⎝ 5 cm ⎠
⎠
Discussion
In reality, the piston velocity must be higher to overcome the losses. Also, a lower piston velocity will do the
job if the diameter of the hole is reduced.
5-34
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-59
Solution
The water height in an airtight pressurized tank is given. A hose pointing straight up is connected to the
bottom of the tank. The maximum height to which the water stream could rise is to be determined.
2
Assumptions 1 The flow is steady, incompressible, and irrotational with
negligible frictional effects (so that the Bernoulli equation is applicable). 2 The
friction between the water and air is negligible.
Properties
2 atm
3
We take the density of water to be 1000 kg/m .
h
Analysis
We take point 1 at the free surface of water in the tank, and point
2 at the top of the water trajectory. Also, we take the reference level at the
bottom of the tank. At the top of the water trajectory V2 = 0, and atmospheric
pressure pertains. Noting that z1 = 20 m, P1,gage = 2 atm, P2 = Patm, and that the
fluid velocity at the free surface of the tank is very low (V1 ≅ 0), the Bernoulli
equation between these two points simplifies to
P1 V12
P V2
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
→
P
P1
+ z1 = atm + z 2 →
ρg
ρg
1
z2 =
20 m
P1,gage
P1 − Patm
+ z1 =
+ z1
ρg
ρg
Substituting,
z2 =
⎛ 101,325 N/m 2 ⎞⎛ 1 kg ⋅ m/s2 ⎞
2 atm
⎜
⎟⎜
⎟ + 20 = 40.7 m
⎟⎜ 1 N
⎟
1 atm
(1000 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
⎠⎝
⎠
Therefore, the water jet can rise as high as 40.7 m into the sky from the ground.
Discussion
The result obtained by the Bernoulli equation represents the upper limit, and should be interpreted
accordingly. It tells us that the water cannot possibly rise more than 40.7 m (giving us an upper limit), and in all likelihood,
the rise will be much less because of frictional losses.
5-35
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-60
Solution
A Pitot-static probe equipped with a water manometer is held parallel to air flow, and the differential height
of the water column is measured. The flow velocity of air is to be determined.
Assumptions 1The flow of air is steady, incompressible, and irrotational with negligible frictional effects (so that the
Bernoulli equation is applicable). 2 The effect of air column on the pressure change is negligible because of its low density,
and thus the air column in the manometer can be ignored.
Properties
We take the density of water to be ρ = 1000 kg/m3. The density of air is given to be 1.25 kg/m3.
Analysis
We take point 1 on the side of the probe where the entrance is parallel to flow and is connected to the static
arm of the Pitot-static probe, and point 2 at the tip of the probe where the entrance is normal to flow and is connected to the
dynamic arm of the Pitot-static probe. Noting that point 2 is a stagnation point and thus V2 = 0 and z1 = z2, the application
of the Bernoulli equation between points 1 and 2 gives
P1 V12
P V2
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P1 V12 P2
+
=
ρg 2 g ρg
→
V1 =
2( P2 − P1 )
ρ air
(1)
The pressure rise at the tip of the Pitot-static probe is simply the pressure change indicated by the differential water column
of the manometer,
P2 − P1 = ρ water gh
(2)
Combining Eqs. (1) and (2) and substituting, the flow velocity is determined to be
V1 =
2 ρ water gh
ρ air
=
2(1000 kg/m 3 )(9.81 m/s 2 )(0.073 m)
1.25 kg/m 3
Air
1
= 33.8 m/s
Pitot
tube
7.3 cm
2
Manometer
Discussion
Note that flow velocity in a pipe or duct can be measured easily by a Pitot-static probe by inserting the
probe into the pipe or duct parallel to flow, and reading the differential height. Also note that this is the velocity at the
location of the tube. Several readings at several locations in a cross-section may be required to determine the mean flow
velocity.
5-36
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-61E
Solution
A Pitot-static probe equipped with a differential pressure gage is used to measure the air velocity in a duct.
For a given differential pressure reading, the flow velocity of air is to be determined.
Assumptions The flow of air is steady, incompressible,
and irrotational with negligible frictional effects (so that the
Bernoulli equation is applicable).
ΔP = 0.15 psi
Properties
The gas constant of air is R = 0.3704
psia⋅ft3/lbm⋅R.
Analysis
We take point 1 on the side of the probe
where the entrance is parallel to flow and is connected to the
static arm of the Pitot-static probe, and point 2 at the tip of
the probe where the entrance is normal to flow and is
connected to the dynamic arm of the Pitot-static probe.
Noting that point 2 is a stagnation point and thus V2 = 0 and
z1 = z2, the application of the Bernoulli equation between
points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P1 V12 P2
+
=
ρg 2 g ρg
→
Air
1
70°F
13.4 psia
V1 =
Pitot
tube
2
2( P2 − P1 )
ρ
where
ρ=
13.4 psia
P
=
= 0.0683 lbm/ft 3
RT (0.3704 psia ⋅ ft 3 /lbm ⋅ R )(70 + 460 R )
Substituting the given values, the flow velocity is determined to be
V1 =
⎛ 144 lbf/ft 2
⎜
0.0683 lbm/ft 3 ⎜⎝ 1 psi
2(0.15 psi )
⎞⎛ 32.2 lbm ⋅ ft/s 2
⎟⎜
⎟⎜
1 lbf
⎠⎝
⎞
⎟ = 143 ft/s
⎟
⎠
Discussion
Note that flow velocity in a pipe or duct can be measured easily by a Pitot-static probe by inserting the
probe into the pipe or duct parallel to flow, and reading the pressure differential. Also note that this is the velocity at the
location of the tube. Several readings at several locations in a cross-section may be required to determine the mean flow
velocity.
5-37
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-62
Solution
In a power plant, water enters the nozzles of a hydraulic turbine at a specified pressure. The maximum
velocity water can be accelerated to by the nozzles is to be determined.
Assumptions 1The flow of water is steady, incompressible, and irrotational with negligible frictional effects (so that the
Bernoulli equation is applicable). 2 Water enters the nozzle with a low velocity.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
We take points 1 and 2 at the inlet and exit of the nozzle, respectively. Noting that V1 ≅ 0 and z1 = z2, the
application of the Bernoulli equation between points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P1
P
V2
= atm + 2
ρg
ρg 2 g
→
V2 =
2( P1 − Patm )
ρ
100 kPa
Water
V
Substituting the given values, the nozzle exit velocity is determined to be
V1 =
2(700 − 100) kPa ⎛ 1000 N/m 2
⎜
1000 kg/m 3 ⎜⎝ 1 kPa
⎞⎛ 1 kg ⋅ m/s 2
⎟⎜
⎟⎜
1N
⎠⎝
⎞
⎟ = 34.6 m/s
⎟
⎠
1
700 kPa
Turbine
nozzzle
2
Discussion
This is the maximum nozzle exit velocity, and the actual
velocity will be less because of friction between water and the walls of the
nozzle.
Energy Equation
5-63C
Solution
fluid.
We are to analyze whether temperature can decrease during steady adiabatic flow of an incompressible
Analysis
It is impossible for the fluid temperature to decrease during steady, incompressible, adiabatic flow of an
incompressible fluid, since this would require the entropy of an adiabatic system to decrease, which would be a violation of
the 2nd law of thermodynamics.
Discussion
The entropy of a fluid can decrease, but only if we remove heat.
5-64C
Solution
We are to determine if frictional effects are negligible in the steady adiabatic flow of an incompressible
fluid if the temperature remains constant.
Analysis
Yes, the frictional effects are negligible if the fluid temperature remains constant during steady,
incompressible flow since any irreversibility such as friction would cause the entropy and thus temperature of the fluid to
increase during adiabatic flow.
Discussion
Thus, this scenario would never occur in real life since all fluid flows have frictional effects.
5-38
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-65C
Solution
We are to define and discuss irreversible head loss.
Analysis
Irreversible head loss is the loss of mechanical energy due to irreversible processes (such as friction) in
piping expressed as an equivalent column height of fluid, i.e., head. Irreversible head loss is related to the mechanical
e mech loss, piping E mech loss, piping
=
energy loss in piping by h L =
.
g
m g
Discussion
hL is always positive. It can never be negative, since this would violate the second law of thermodynamics.
5-66C
Solution
We are to define and discuss useful pump head.
Useful pump head is the useful power input to the pump expressed as an equivalent column height of
w pump, u W pump, u
=
fluid. It is related to the useful pumping power input by hpump =
.
g
m g
Analysis
Discussion
Part of the power supplied to the pump is not useful, but rather is wasted because of irreversible losses in
the pump. This is the reason that pumps have a pump efficiency that is always less than one.
5-67C
Solution
We are to define and discuss the kinetic energy correction factor.
Analysis
The kinetic energy correction factor is a correction factor to account for the fact that kinetic energy
using average velocity is not the same as the actual kinetic energy using the actual velocity profile (the square of a
sum is not equal to the sum of the squares of its components). The effect of kinetic energy factor is usually negligible,
especially for turbulent pipe flows. However, for laminar pipe flows, the effect of α is sometimes significant.
Discussion
Even though the effect of ignoring α is usually insignificant, it is wise to keep α in our analyses to increase
accuracy and so that we do not forget about it in situations where it is significant, such as in some laminar pipe flows.
5-68C
Solution
We are to analyze the cause of some strange behavior of a water jet.
Analysis
The problem does not state whether the water in the tank is open to the atmosphere or not. Let’s assume that
the water surface is exposed to atmospheric pressure. By the Bernoulli equation, the maximum theoretical height to which
the water stream could rise is the tank water level, which is 20 meters above the ground. Since the water rises above the
tank level, the tank cover must be airtight, containing pressurized air above the water surface. In other words, the water in
the tank is not exposed to atmospheric pressure.
Discussion
Alternatively, a pump would have to pressurize the water somewhere in the hose.
5-39
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-69
Solution
Underground water is pumped to a pool at a given elevation. The maximum flow rate and the pressures at
the inlet and outlet of the pump are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The elevation difference between the inlet and the outlet of the
pump is negligible. 3 We assume the frictional effects in piping to be negligible since the maximum flow rate is to be
determined, E mech loss, pipping = 0. 4 The effect of the kinetic energy correction factors is negligible, α = 1.
Properties
We take the density of water to be 1 kg/L = 1000 kg/m3.
Analysis
(a) The pump-motor draws 3-kW of power, and is 70% efficient. Then the useful mechanical (shaft) power
it delivers to the fluid is
W pump, u = η pump- motor W electric = (0.70)(3 kW) = 2.1 kW
We take point 1 at the free surface of underground water, which is also taken as the reference level (z1 = 0), and point 2 at
the free surface of the pool. Also, both 1 and 2 are open to the atmosphere (P1 = P2 = Patm), the velocities are negligible at
both points (V1 ≅ V2 ≅ 0), and frictional losses in piping are disregarded. Then the energy equation for steady
incompressible flow through a control volume between these two points that includes the pump and the pipes reduces to
⎞
⎛P
⎞
⎛P
V2
V2
m ⎜ 1 + α 1 1 + gz1 ⎟⎟ + W pump = m ⎜⎜ 2 + α 2 2 + gz 2 ⎟⎟ + W turbine + E mech,loss
2
⎜ρ
2
2
⎠
⎝ ρ
⎠
⎝
Pool
and
In the absence of a turbine, E
= E
+ E
mech, loss
mech loss, pump
mech loss, piping
W pump, u = W pump − E mech loss, pump .
30 m
Thus, W pump, u = m gz 2 .
Then the mass and volume flow rates of water become
m =
W pump, u
gz 2
=
1
⎛ 1000 m /s ⎞
⎟ = 7.14 kg/s
⎜
⎟
1 kJ
(9.81 m/s )(30 m) ⎜⎝
⎠
2.1 kJ/s
2
2
2
Pump
7.14 kg/s
m
V = =
= 7.14 × 10 −3 m 3 /s
ρ 1000 kg/m 3
(b) We take points 3 and 4 at the inlet and the exit of the pump, respectively, where the flow velocities are
V
V
V
V
7.14 × 10 −3 m 3 /s
7.14 × 10 −3 m 3 /s
=
=
=
=
=
=
= 3.64 m/s
1
.
86
m/s
,
V3 =
V
4
A3 πD32 / 4
A4 πD 42 / 4
π (0.07 m) 2 / 4
π (0.05 m) 2 / 4
We take the pump as the control volume. Noting that z3 = z4, the energy equation for this control volume reduces to
⎛P
⎞
⎞
⎛P
V2
V2
ρα (V32 − V 42 ) W pump, u
m ⎜ 3 + α 3 3 + gz 3 ⎟ + W pump = m ⎜ 4 + α 4 4 + gz 4 ⎟ + W turbine + E mech loss, pump → P4 − P3 =
+
⎟
⎜ ρ
⎜ ρ
⎟
2
2
2
V
⎠
⎝
⎝
⎠
Substituting,
2
2
(1000 kg/m3 )(1.0) ⎡(1.86 m/s ) − ( 3.64 m/s ) ⎤ ⎛
1 kN
⎣
⎦
P4 − P3 =
⎜
2
2
⎝ 1000 kg ⋅ m/s
= ( −4.9 + 294.1) kN/m 2 = 289.2 kPa ≅ 289 kPa
⎞
2.1 kJ/s
⎛ 1 kN ⋅ m ⎞
⎟+
⎜
⎟
-3
3
⎠ 7.14 × 10 m /s ⎝ 1 kJ ⎠
In an actual system, the flow rate of water will be less because of friction in the pipes. Also, the effect of
Discussion
flow velocities on the pressure change across the pump is negligible in this case (under 2%) and can be ignored.
5-40
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-70
Solution
Underground water is pumped to a pool at a given elevation. For a given head loss, the flow rate and the
pressures at the inlet and outlet of the pump are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The elevation difference between the inlet and the outlet of the
pump is negligible. 3 The effect of the kinetic energy correction factors is negligible, α = 1.
Properties
We take the density of water to be 1 kg/L = 1000 kg/m3.
Analysis
(a) The pump-motor draws 3-kW of power, and is 70% efficient. Then the useful mechanical (shaft) power
it delivers to the fluid is
W pump, u = η pump - motor W electric = (0.70 )(3 kW) = 2.1 kW
We take point 1 at the free surface of underground water, which is also taken as the reference level (z1 = 0), and point 2 at
the free surface of the pool. Also, both 1 and 2 are open to the atmosphere (P1 = P2 = Patm), and the velocities are negligible
at both points (V1 ≅ V2 ≅ 0). Then the energy equation for steady incompressible flow through a control volume between
these two points that includes the pump and the pipes reduces to
⎛P
⎞
⎛P
⎞
V2
V2
m ⎜⎜ 1 + α 1 1 + gz1 ⎟⎟ + W pump = m ⎜⎜ 2 + α 2 2 + gz 2 ⎟⎟ + W turbine + E mech,loss
2
2
⎝ρ
⎠
⎝ ρ
⎠
In the absence of a turbine, E mech, loss = E mech loss, pump + E mech loss, piping and W pump, u = W pump − E mech loss, pump and thus
W pump, u = m gz 2 + E mech loss, piping
2
Noting that E mech, loss = m gh L , the mass and volume flow rates of water become
m =
=
W pump, u
gz 2 + gh L
=
Pool
W pump, u
g ( z 2 + hL )
30 m
⎛ 1000 m 2 /s 2 ⎞
⎜
⎟ = 6.116 kg/s
⎟
1 kJ
(9.81 m/s )(30 + 5 m) ⎜⎝
⎠
2.1 kJ/s
2
1
Pump
6.116 kg/s
m
V = =
= 6.116m 3 / s ≅ 6.12 × 10 −3 m 3 /s
3
ρ 1000 kg/m
(b) We take points 3 and 4 at the inlet and the exit of the pump, respectively, where the flow velocities are
V
V
V
V
6.116 × 10 −3 m 3 /s
6.116 × 10 −3 m 3 /s
V3 =
V
,
=
=
=
1
.
589
m/s
=
=
=
= 3.115 m/s
4
A3 πD32 / 4
A4 πD 42 / 4
π (0.07 m) 2 / 4
π (0.05 m) 2 / 4
We take the pump as the control volume. Noting that z3 = z4, the energy equation for this control volume reduces to
⎛P
⎞
⎞
⎛P
V2
V2
ρα (V32 − V 42 ) W pump, u
m ⎜ 3 + α 3 3 + gz 3 ⎟ + W pump = m ⎜ 4 + α 4 4 + gz 4 ⎟ + W turbine + E mech loss, pump → P4 − P3 =
+
⎟
⎜ ρ
⎜ ρ
⎟
2
2
2
V
⎠
⎝
⎝
⎠
Substituting,
2
2
(1000 kg/m3 )(1.0) ⎡(1.589 m/s ) − ( 3.115 m/s ) ⎤ ⎛
⎞
1 kN
2.1 kJ/s
⎛ 1 kN ⋅ m ⎞
⎣
⎦
P4 − P3 =
+
⎜
⎜
⎟
2 ⎟
-3
3
2
1000
kg
m/s
6.116
10
m
/s
⋅
×
⎝ 1 kJ ⎠
⎝
⎠
= ( −3.6 + 343.4 ) kN/m 2 = 339.8 kPa ≅ 340 kPa
Discussion
Note that frictional losses in the pipes causes the flow rate of water to decrease. Also, the effect of flow
velocities on the pressure change across the pump is negligible in this case (about 1%) and can be ignored.
5-41
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-71E
Solution
In a hydroelectric power plant, the elevation difference, the power generation, and the overall turbinegenerator efficiency are given. The minimum flow rate required is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The
water levels at the reservoir and the discharge site remain
constant. 3 We assume the flow to be frictionless since the
minimum flow rate is to be determined, E mech,loss = 0.
Properties
lbm/ft3.
We take the density of water to be ρ = 62.4
Analysis
We take point 1 at the free surface of the
reservoir and point 2 at the free surface of the discharge water
stream, which is also taken as the reference level (z2 = 0). Also,
both 1 and 2 are open to the atmosphere (P1 = P2 = Patm), the
velocities are negligible at both points (V1 = V2 = 0), and
frictional losses are disregarded. Then the energy equation in
terms of heads for steady incompressible flow through a control
volume between these two points that includes the turbine and
the pipes reduces to
1
Water
240 ft
2
Turbine
Generator
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L → hturbine, e = z1
2g
2g
ρg
ρg
Substituting and noting that W turbine, elect = η turbine -gen m ghturbine, e , the extracted turbine head and the mass and volume flow
rates of water are determined to be
hturbine, e = z1 = 240 ft
m =
W turbine,elect
η turbine-gen ghturbine
=
⎛ 25,037 ft 2 /s 2
⎜
0.83(32.2 ft/s 2 )(240 ft) ⎜⎝ 1 Btu/lbm
100 kW
⎞⎛ 0.9478 Btu/s ⎞
⎟⎜
⎟ = 370 lbm/s
⎟⎝
1 kW
⎠
⎠
m
370 lbm/s
= 5.93 ft 3 /s
V = =
ρ 62.4 lbm/ft 3
Therefore, the flow rate of water must be at least 5.93 ft3/s to generate the desired electric power while overcoming friction
losses in pipes.
Discussion
In an actual system, the flow rate of water will be more because of frictional losses in pipes.
5-42
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-72E
Solution
In a hydroelectric power plant, the elevation difference, the head loss, the power generation, and the overall
turbine-generator efficiency are given. The flow rate required is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The
water levels at the reservoir and the discharge site remain
constant.
Properties
lbm/ft3.
We take the density of water to be ρ = 62.4
Analysis
We take point 1 at the free surface of the
reservoir and point 2 at the free surface of the discharge water
stream, which is also taken as the reference level (z2 = 0). Also,
both 1 and 2 are open to the atmosphere (P1 = P2 = Patm), the
velocities are negligible at both points (V1 = V2 = 0). Then the
energy equation in terms of heads for steady incompressible
flow through a control volume between these two points that
includes the turbine and the pipes reduces to
1
Water
240 ft
2
Turbine
Generator
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + hturbine, e + h L → hturbine, e = z1 − h L
ρg
ρg
2g
2g
Substituting and noting that W turbine, elect = η turbine -gen m ghturbine, e , the extracted turbine head and the mass and volume flow
rates of water are determined to be
hturbine, e = z1 − h L = 240 − 36 = 204 ft
m =
W turbine,elect
η turbine-gen ghturbine
=
⎛ 25,037 ft 2 /s 2
⎜
0.83(32.2 ft/s 2 )(204 ft) ⎜⎝ 1 Btu/lbm
100 kW
⎞⎛ 0.9478 Btu/s ⎞
⎟⎜
⎟ = 435 lbm/s
⎟⎝
1 kW
⎠
⎠
435 lbm/s
m
= 6.98 ft 3 /s
V = =
3
ρ 62.4 lbm/ft
Therefore, the flow rate of water must be at least 6.98 ft3/s to generate the desired electric power while overcoming friction
losses in pipes.
Discussion
Note that the effect of frictional losses in the pipes is to increase the required flow rate of water to generate a
specified amount of electric power.
5-43
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-73 [Also solved using EES on enclosed DVD]
Solution
A fan is to ventilate a bathroom by replacing the entire volume of air once every 10 minutes while air
velocity remains below a specified value. The wattage of the fan-motor unit, the diameter of the fan casing, and the pressure
difference across the fan are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 Frictional losses
along the flow (other than those due to the fan-motor inefficiency) are
negligible. 3 The fan unit is horizontal so that z = constant along the flow (or,
the elevation effects are negligible because of the low density of air). 4 The
effect of the kinetic energy correction factors is negligible, α = 1.
1
Air
8 m/s
D
2
The density of air is given to be 1.25 kg/m3.
Properties
Analysis
(a) The volume of air in the bathroom is V = 2 m × 3 m × 3 m = 18 m3.
Then the volume and mass flow rates of air through the casing must be
V
18 m 3
V =
=
= 0.03 m 3 /s
Δt 10 × 60 s
m = ρV = (1.25 kg/m 3 )(0.03 m 3 /s) = 0.0375 kg/s
We take points 1 and 2 on the inlet and exit sides of the fan, respectively. Point 1 is sufficiently far from the fan so that P 1
= Patm and the flow velocity is negligible (V1 = 0). Also, P2 = Patm. Then the energy equation for this control volume
between the points 1 and 2 reduces to
⎛P
⎞
⎛P
⎞
V2
V2
m ⎜⎜ 1 + α 1 1 + gz1 ⎟⎟ + W pump = m ⎜⎜ 2 + α 2 2 + gz 2 ⎟⎟ + W turbine + E mech,loss →
2
2
⎝ρ
⎠
⎝ ρ
⎠
V2
W fan, u = m α 2 2
2
since E mech, loss = E mech loss, pump in this case and W pump, u = W pump − E mech loss, pump . Substituting,
V2
(8 m/s) 2
W fan, u = m α 2 2 = (0.0375 kg/s)(1.0)
2
2
and
W fan, elect =
W fan, u
η fan-motor
=
⎛
1N
⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞⎛ 1 W ⎞
⎟⎜
⎟⎝ 1 N ⋅ m/s ⎟⎠ = 1.2 W
⎠
1.2 W
= 2.4 W
0.5
Therefore, the electric power rating of the fan/motor unit must be 2.4 W.
(b) For air mean velocity to remain below the specified value, the diameter of the fan casing should be
4(0.03 m 3 /s)
4V
→ D2 =
=
= 0.069 m = 6.9 cm
V = A2V 2 = (πD 22 / 4 )V 2
πV 2
π (8 m/s)
(c) To determine the pressure difference across the fan unit, we take points 3 and 4 to be on the two sides of the fan on a
horizontal line. Noting that z3 = z4 and V3 = V4 since the fan is a narrow cross-section and neglecting flow loses (other than
the loses of the fan unit, which is accounted for by the efficiency), the energy equation for the fan section reduces to
W fan, u W fan, u
P
P
m 3 + W fan, u = m 4
→ P4 − P3 =
=
m / ρ
ρ
ρ
V
⎛ 1 N ⋅ m/s ⎞
2
⎜
⎟ = 40 N/m = 40 Pa
0.03 m /s ⎝ 1 W ⎠
Therefore, the fan will raise the pressure of air by 40 Pa before discharging it.
Substituting ,
P4 − P3 =
1.2 W
3
Discussion
Note that only half of the electric energy consumed by the fan-motor unit is converted to the mechanical
energy of air while the remaining half is converted to heat because of imperfections.
5-44
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-74
Solution
Water is pumped from a large lake to a higher reservoir. The head loss of the piping system is given. The
mechanical efficiency of the pump is to be determined.
2
Assumptions 1 The flow is steady and incompressible. 2 The
elevation difference between the lake and the reservoir is constant.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Reservoir
25 m
Analysis
We choose points 1 and 2 at the free surfaces of the
lake and the reservoir, respectively, and take the surface of the lake as
the reference level (z1 = 0). Both points are open to the atmosphere (P1
= P2 = Patm) and the velocities at both locations are negligible (V1 = V2
= 0). Then the energy equation for steady incompressible flow through
a control volume between these two points that includes the pump and
the pipes reduces to
Pump
1
Lake
⎛P
⎞
⎛P
⎞
V2
V2
m ⎜⎜ 1 + α 1 1 + gz1 ⎟⎟ + W pump = m ⎜⎜ 2 + α 2 2 + gz 2 ⎟⎟ + W turbine + E mech,loss → W pump, u = m gz 2 + E mech loss, piping
2
2
⎝ρ
⎠
⎝ ρ
⎠
since, in the absence of a turbine, E mech, loss = E mech loss, pump + E mech loss, piping and W pump, u = W pump − E mech loss, pump . Noting
that E mech loss, piping = m gh L , the useful pump power is
W pump,u = m gz 2 + m gh L = ρVg ( z 2 + h L )
⎛
1 kN
= (1000 kg/m 3 )(0.025 m 3 /s)(9.81m / s 2 )[(25 + 7) m]⎜
⎜ 1000 kg ⋅ m/s 2
⎝
= 7.85 kNm/s = 7.85 kW
⎞
⎟
⎟
⎠
Then the mechanical efficiency of the pump becomes
η pump =
W pump, u 7.85 kW
=
= 0.785 = 78.5%
10 kW
W shaft
Discussion
A more practical measure of performance of the pump is the overall efficiency, which can be obtained by
multiplying the pump efficiency by the motor efficiency.
5-45
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-75
Solution
The previous problem is reconsidered. The effect of head loss on mechanical efficiency of the pump. as the
head loss varies 0 to 20 m in increments of 2 m is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
g=9.81 "m/s2"
rho=1000 "kg/m3"
z2=25 "m"
W_shaft=10 "kW"
V_dot=0.025 "m3/s"
W_pump_u=rho*V_dot*g*(z2+h_L)/1000 "kW"
Eta_pump=W_pump_u/W_shaft
Pumping power
Wpump, u
6.13
6.38
6.62
6.87
7.11
7.36
7.60
7.85
8.09
8.34
8.58
8.83
9.07
9.32
9.56
9.81
Efficiency
1
ηpump
0.613
0.638
0.662
0.687
0.711
0.736
0.760
0.785
0.809
0.834
0.858
0.883
0.907
0.932
0.956
0.981
0.95
0.9
0.85
ηpump
Head Loss,
hL, m
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0.8
0.75
0.7
0.65
0.6
0
2
4
6
8
10
12
14
16
hL, m
Note that the useful pumping power is used to raise the fluid and to overcome head losses. For a given
Discussion
power input, the pump that overcomes more head loss is more efficient.
5-46
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-76
Solution
A pump with a specified shaft power and efficiency is used to raise water to a higher elevation. The
maximum flow rate of water is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The elevation difference between the reservoirs is constant. 3
We assume the flow in the pipes to be frictionless since the maximum flow rate is to be determined, E mech loss, piping = 0.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
We choose points 1 and 2 at the free surfaces of the lower and upper reservoirs, respectively, and take the
surface of the lower reservoir as the reference level (z1 = 0). Both points are open to the atmosphere (P1 = P2 = Patm) and the
velocities at both locations are negligible (V1 = V2 = 0). Then the energy equation for steady incompressible flow through a
control volume between these two points that includes the pump and the pipes reduces to
⎛P
⎞
⎛P
⎞
V2
V2
m ⎜⎜ 1 + α 1 1 + gz1 ⎟⎟ + W pump = m ⎜⎜ 2 + α 2 2 + gz 2 ⎟⎟ + W turbine + E mech,loss → W pump, u = m gz 2 = ρVgz 2
2
2
⎝ρ
⎠
⎝ ρ
⎠
since E mech, loss = E mech loss, pump in this case and W pump, u = W pump − E mech loss, pump .
2
The useful pumping power is
W pump, u = η pump W pump, shaft = (0.82)(7 hp) = 5.74 hp
Substituting, the volume flow rate of water is determined to be
V =
W pump, u
ρgz 2
=
⎛ 745.7 W ⎞⎛ 1 N ⋅ m/s ⎞⎛ 1 kg ⋅ m/s 2
⎟⎜
⎜
⎟⎜
1N
(1000 kg/m 3 )(9.81 m/s 2 )(15 m) ⎜⎝ 1 hp ⎟⎠⎝ 1 W ⎠⎜⎝
5.74 hp
⎞
⎟
⎟
⎠
PUMP
15 m
= 0.0291 m 3 /s
1
Water
This is the maximum flow rate since the frictional effects are ignored.
Discussion
In an actual system, the flow rate of water will be less because of friction in pipes.
5-47
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-77
Solution
Water flows at a specified rate in a horizontal pipe whose diameter is decreased by a reducer. The pressures
are measured before and after the reducer. The head loss in the reducer is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The pipe is horizontal. 3 The kinetic energy correction factors
are given to be α1 = α2 = α = 1.05.
We take the density of water to be ρ = 1000 kg/m3.
Properties
Analysis
We take points 1 and 2 along the centerline of the pipe before and after the reducer, respectively. Noting
that z1 = z2, the energy equation for steady incompressible flow through a control volume between these two points reduces
to
P
V2
P1
V2
+ α 1 1 + z1 + h pump, u = 2 + α 2 2 + z 2 + hturbine, e + h L
ρg
ρg
2g
2g
→
hL =
P1 − P2 α (V12 − V 22 )
+
2g
ρg
where
V1 =
V
V
0.035 m 3 /s
=
=
= 1.98 m/s
A1 πD12 / 4 π (0.15 m) 2 / 4
V2 =
V
V
0.035 m 3 /s
=
=
= 6.96 m/s
A2 πD 22 / 4 π (0.08 m) 2 / 4
1
470 kPa
15 cm
Water
440 kPa
2
8 cm
Reducer
Substituting, the head loss in the reducer is determined to be
⎛ 1 kN/m 2
⎜
(1000 kg/m 3 )(9.81 m/s 2 ) ⎜⎝ 1 kPa
= 3.06 − 2.38 = 0.68 m
hL =
(470 - 440) kPa
⎞⎛ 1000 kg ⋅ m/s 2
⎟⎜
⎟⎜
1 kN
⎠⎝
⎞ 1.05[(1.98 m/s ) 2 − (6.96 m/s) 2 ]
⎟+
⎟
2(9.81 m/s 2 )
⎠
Note that the 0.79 m of the head loss is due to frictional effects and 2.27 m is due to the increase in velocity.
Discussion
This head loss corresponds to a power potential loss of
⎛
1N
E mech loss, piping = ρVgh L = (1000 kg/m 3 )(0.035 m 3 /s)(9.81 m/s 2 )(0.79 m)⎜⎜
1
kg
⋅ m/s 2
⎝
5-48
⎞⎛ 1 W ⎞
⎟⎜
⎟⎝ 1 N ⋅ m/s ⎟⎠ = 271 W
⎠
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-78
Solution
A hose connected to the bottom of a tank is equipped with a nozzle at the end pointing straight up. The
water is pressurized by a pump, and the height of the water jet is measured. The minimum pressure rise supplied by the
pump is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 Friction between the water and air as well as friction in the hose
is negligible. 3 The water surface is open to the atmosphere.
We take the density of water to be ρ = 1000 kg/m3.
Properties
Analysis
We take point 1 at the free surface of water in the tank, and point 2 at the top of the water trajectory where
V2 = 0 and P1 = P2 = Patm. Also, we take the reference level at the bottom of the tank. Noting that z1 = 20 m and z2 = 27 m,
hL =0 (to get the minimum value for required pressure rise), and that the fluid velocity at the free surface of the tank is very
low (V1 ≅ 0), the energy equation for steady incompressible flow through a control volume between these two points that
includes the pump and the water stream reduces to
P
V2
P1
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
ρg
ρg
2g
2g
→
2
hpump, u = z 2 − z1
Substituting,
hpump, u = 27 − 20 = 7 m
27 m
1
A water column height of 7 m corresponds to a pressure rise of
20 m
⎞
⎛
1N
⎟
ΔPpump, min = ρghpump, u = (1000 kg/m 3 )(9.81 m/s 2 )(7 m)⎜⎜
2⎟
1000
kg
m/s
⋅
⎠
⎝
= 68.7 kN/m 2 = 68.7 kPa
Therefore, the pump must supply a minimum pressure rise of 68.7 kPa.
Discussion
The result obtained above represents the minimum value, and should be interpreted accordingly. In reality, a
larger pressure rise will need to be supplied to overcome friction.
5-79
Solution
The available head of a hydraulic turbine and its overall efficiency are given. The electric power output of
this turbine is to be determined.
Assumptions
1 The flow is steady and incompressible. 2 The available head remains constant.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
When the turbine head is available, the corresponding power output is
determined from
Eff.=78%
Turbine
W turbine = η turbine m ghturbine = η turbine ρVghturbine
Generator
Substituting,
⎛
1N
W turbine = 0.78(1000 kg/m 3 )(0.25 m 3 /s)(9.81 m/s 2 )(85 m)⎜⎜
2
⎝ 1 kg ⋅ m/s
Discussion
⎞⎛
1 kW
⎞
⎟⎜
⎟⎝ 1000 N ⋅ m/s ⎟⎠ = 163 kW
⎠
The power output of a hydraulic turbine is proportional to the available turbine head and the flow rate.
5-49
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-80
Solution
An entrepreneur is to build a large reservoir above the lake level, and pump water from the lake to the
reservoir at night using cheap power, and let the water flow from the reservoir back to the lake during the day, producing
power. The potential revenue this system can generate per year is to be determined.
Assumptions 1 The flow in each direction is steady and
incompressible. 2 The elevation difference between the lake
and the reservoir can be taken to be constant, and the elevation
change of reservoir during charging and discharging is
disregarded. 3 The given unit prices remain constant. 4 The
system operates every day of the year for 10 hours in each
mode.
Properties
kg/m3.
3
Reservoir
2
Pumpturbine
40 m
Lake 4
1
We take the density of water to be ρ = 1000
Analysis
We choose points 1 and 2 at the free surfaces of the lake and the reservoir, respectively, and take the surface
of the lake as the reference level. Both points are open to the atmosphere (P1 = P2 = Patm) and the velocities at both locations
are negligible (V1 = V2 = 0). Then the energy equation in terms of heads for steady incompressible flow through a control
volume between these two points that includes the pump (or the turbine) and the pipes reduces to
Pump mode:
P
V2
P1
V2
+ α 1 1 + z1 + h pump, u = 2 + α 2 2 + z 2 + hturbine, e + h L →
ρg
ρg
2g
2g
hpump, u = z 2 + h L = 40 + 4 = 44 m
Turbine mode: (switch points 1 and 2 so that 1 is on inlet side)
→
hturbine, e = z1 − h L = 40 − 4 = 36 m
The pump and turbine power corresponding to these heads are
W pump, elect =
=
W pump, u
η pump-motor
=
ρVghpump, u
η pump-motor
(1000 kg/m 3 )(2 m 3 /s)(9.81 m/s 2 )(44 m) ⎛
1N
⎜
⎜ 1 kg ⋅ m/s 2
0.75
⎝
⎞⎛
1 kW
⎞
⎟⎜
⎟⎝ 1000 N ⋅ m/s ⎟⎠ = 1151 kW
⎠
W turbine = η turbine-gen m ghturbine, e = η turbine-gen ρVghturbine, e
⎛
1N
= 0.75(1000 kg/m 3 )(2 m 3 /s)(9.81 m/s 2 )(36 m)⎜⎜
2
⎝ 1 kg ⋅ m/s
⎞⎛
1 kW
⎞
⎟⎜
⎟⎝ 1000 N ⋅ m/s ⎟⎠ = 530 kW
⎠
Then the power cost of the pump, the revenue generated by the turbine, and the net income (revenue minus cost) per year
become
Cost = W pump, elect Δt × Unit price = (1151 kW)(365 × 10 h/year)($0.03/kWh) = $126,035/year
Revenue = W turbine Δt × Unit price = (530 kW)(365 × 10 h/year)($0.08/kWh) = $154,760/year
Net income = Revenue – Cost = 154,760 –126,035 = $28,725/year ≅ $28,700/year
Discussion
It appears that this pump-turbine system has a potential annual income of about $29,000. A decision on
such a system will depend on the initial cost of the system, its life, the operating and maintenance costs, the interest rate,
and the length of the contract period, among other things.
5-50
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-81
Solution
Water flows through a horizontal pipe at a specified rate. The pressure drop across a valve in the pipe is
measured. The corresponding head loss and the power needed to overcome it are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The pipe is given to be horizontal (otherwise the elevation
difference across the valve is negligible). 3 The mean flow velocities at the inlet and the exit of the valve are equal since
the pipe diameter is constant.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
We take the valve as the control volume, and points 1 and 2 at the inlet and exit of the valve, respectively.
Noting that z1 = z2 and V1 = V2, the energy equation for steady incompressible flow through this control volume reduces to
P
V2
P1
V2
+ α 1 1 + z1 + h pump, u = 2 + α 2 2 + z 2 + hturbine, e + h L
ρg
ρg
2g
2g
→
Substituting,
hL =
hL =
P1 − P2
ρg
Valve
⎛ 1000 kg ⋅ m/s 2 ⎞
2 kN/m 2
⎜
⎟ = 0.204 m
3
2 ⎜
⎟
1 kN
(1000 kg/m )(9.81 m/s ) ⎝
⎠
Water
1
2
20 L/s
The useful pumping power needed to overcome this head loss is
ΔP=2 kPa
W pump, u = m gh L = ρVgh L
⎛
1N
= (1000 kg/m 3 )(0.020 m 3 /s)(9.81 m/s 2 )(0.204 m)⎜⎜
2
⎝ 1 kg ⋅ m/s
⎞⎛ 1 W ⎞
⎟⎜
⎟⎝ 1 N ⋅ m/s ⎟⎠ = 40 W
⎠
Therefore, this valve would cause a head loss of 0.204 m, and it would take 40 W of useful pumping power to overcome it.
Discussion
The required useful pumping power could also be determined from
⎛ 1W ⎞
W pump = VΔP = (0.020 m 3 /s)(2000 Pa)⎜
⎟ = 40 W
⎝ 1 Pa ⋅ m 3 /s ⎠
5-51
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-82E
Solution
A hose connected to the bottom of a pressurized tank is equipped with a nozzle at the end pointing straight
up. The minimum tank air pressure (gage) corresponding to a given height of water jet is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 Friction between water and air as well as friction in the hose is
negligible. 3 The water surface is open to the atmosphere.
2
Properties
We take the density of water to be ρ = 62.4 lbm/ft3.
Analysis
We take point 1 at the free surface of water in the tank, and point
2 at the top of the water trajectory where V2 = 0 and P1 = P2 = Patm. Also, we
take the reference level at the bottom of the tank. Noting that z1 = 66 ft and z2 =
90 ft, hL = 0 (to get the minimum value for the required air pressure), and that
the fluid velocity at the free surface of the tank is very low (V1 ≅ 0), the energy
equation for steady incompressible flow through a control volume between these
two points reduces to
P1
1
90 ft
66 ft
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
2g
2g
ρg
ρg
or
P1, gage
P1 − Patm
= z 2 − z1 →
= z 2 − z1
ρg
ρg
Rearranging and substituting, the gage pressure of pressurized air in the tank is determined to be
1 lbf
⎛
⎞ ⎛ 1 psi ⎞
= 10.4 psi
P1, gage = ρ g ( z2 − z1 ) = ( 62.4 lbm/ft 3 )( 32.2 ft/s 2 ) ( 90 − 66 ft ) ⎜
2 ⎟⎜
2 ⎟
⋅
32
.
2
lbm
ft/s
⎝
⎠ ⎝ 144 lbf/ft ⎠
Therefore, the gage air pressure on top of the water tank must be at least 10.4 psi.
Discussion
The result obtained above represents the minimum value, and should be interpreted accordingly. In reality, a
larger pressure will be needed to overcome friction.
5-83
Solution
A water tank open to the atmosphere is initially filled with water. A sharp-edged orifice at the bottom drains
to the atmosphere. The initial discharge velocity from the tank is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The tank is open to the atmosphere. 3 The kinetic energy
correction factor at the orifice is given to be α2 = α = 1.2.
Analysis
We take point 1 at the free surface of the tank, and point 2 at the exit of the orifice. Noting that the fluid at
both points is open to the atmosphere (and thus P1 = P2 = Patm) and that the fluid velocity at the free surface of the tank is
very low (V1 ≅ 0), the energy equation between these two points (in terms of heads) simplifies to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
2g
2g
ρg
ρg
1
which yields
z1 + α 2
V 22
= z 2 + hL
2g
Water
2m
Solving for V2 and substituting,
V 2 = 2 g ( z 1 − z 2 − h L ) / α = 2(9.81 m/s 2 )( 2 − 0.3 m ) / 1.2 = 5.27 m/s
2
10 cm
Discussion
This is the velocity that will prevail at the beginning. The mean flow velocity will decrease as the water
level in the tank decreases.
5-52
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-84
Solution
Water enters a hydraulic turbine-generator system with a known flow rate, pressure drop, and efficiency.
The net electric power output is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 All losses in the turbine are accounted for by turbine efficiency
and thus hL = 0. 3 The elevation difference across the turbine is negligible. 4 The effect of the kinetic energy correction
factors is negligible, α1 = α2 = α = 1.
Properties
We take the density of water to be 1000 kg/m3 and the density of mercury to be 13,560 kg/m3.
Analysis
We choose points 1 and 2 at the inlet and the exit of the turbine, respectively. Noting that the elevation
effects are negligible, the energy equation in terms of heads for the turbine reduces to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + hturbine, e + h L
2g
2g
ρg
ρg
→
P1 − P2 α (V12 − V 22 )
+
2g
ρ water g
hturbine, e =
(1)
where
V1 =
0.6 m 3 /s
V
V
=
= 8.49 m/s
A1 πD12 / 4 π (0.30 m) 2 / 4
1
We
Turbine
0.6 m 3 /s
V
V
=
=
= 12.2 m/s
V2 =
2
A2 πD 2 / 4 π (0.25 m) 2 / 4
Generator
The pressure drop corresponding to a differential height of 1.2 m in the mercury
manometer is
2
P1 − P2 = ( ρ Hg − ρ water ) gh
⎛
1 kN
= [(13,560 − 1000) kg/m 3 ](9.81 m/s 2 )(1.2 m)⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟
⎟
⎠
= 148 kN/m 2 = 148 kPa
Substituting into Eq. (1), the turbine head is determined to be
hturbine, e =
⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
(1000 kg/m )(9.81 m/s ) ⎜⎝
148 kN/m 2
3
2
⎞
(8.49 m/s ) 2 − (12.2 m/s) 2
⎟ + (1.0)
= 15.1 − 3.9 = 11.2 m
⎟
2(9.81 m/s 2 )
⎠
Then the net electric power output of this hydroelectric turbine becomes
W turbine = η turbine-gen m ghturbine, e = η turbine-gen ρVghturbine, e
⎛
1N
= 0.83(1000 kg/m 3 )(0.6 m 3 /s)(9.81 m/s 2 )(11.2 m)⎜⎜
1
kg
⋅ m/s 2
⎝
⎞⎛
1 kW
⎞
⎟⎜
⎟⎝ 1000 N ⋅ m/s ⎟⎠ = 55 kW
⎠
Discussion
It appears that this hydroelectric turbine will generate 55 kW of electric power under given conditions. Note
that almost half of the available pressure head is discarded as kinetic energy. This demonstrates the need for a larger turbine
exit area and better recovery. For example, the power output can be increased to 74 kW by redesigning the turbine and
making the exit diameter of the pipe equal to the inlet diameter, D2 = D1. Further, if a much larger exit diameter is used and
the exit velocity is reduced to a very low level, the power generation can increase to as much as 92 kW.
5-53
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-85
Solution
The velocity profile for turbulent flow in a circular pipe is given. The kinetic energy correction factor for
this flow is to be determined.
Analysis
The velocity profile is given by u (r ) = u max (1 − r / R ) 1 / n with n = 7 The kinetic energy correction factor is
then expressed as
1
α=
A
3
⎛ u (r ) ⎞
⎜
⎟ dA = 1
3
A ⎜ V avg ⎟
AV avg
⎝
⎠
∫
∫ u (r )
3
dA =
A
1
3
πR 2V avg
∫
R
r =0
3 ⎛
u max
⎜1 −
⎝
3
3
2u max
r ⎞n
⎟ (2πr )dr = 2 3
R⎠
R V avg
3
r ⎞n
⎛
⎜1 − ⎟ rdr
r =0 ⎝
R⎠
∫
R
where the average velocity is
V avg =
1
1
u (r )dA =
A A
πR 2
∫
r⎞
⎛
u max ⎜1 − ⎟
r =0
⎝ R⎠
∫
R
1/ n
( 2πr ) dr =
r⎞
⎛
⎜1 − ⎟
r =0 ⎝
R⎠
2u max
∫
R2
R
1/ n
rdr
From integral tables,
∫
( a + bx ) n xdx =
( a + bx ) n + 2
b ( n + 2)
2
−
a ( a + bx ) n +1
u(r)
2r
b ( n + 1)
2
Then,
R
∫
R
u (r )rdr =
r =0
r⎞
⎛
⎜1 − ⎟
r =0 ⎝
R⎠
∫
R
1/ n
rdr =
1
+2
n
1
+1
n
(1 − r / R )
(1 − r / R )
−
1 1
1 1
( + 2)
( n + 1)
2 n
R
R2
=
n2R2
( n + 1)(2n + 1)
r =0
R
∫
R
u (r ) 3 rdr =
r =0
r⎞
⎛
⎜1 − ⎟
r =0 ⎝
R⎠
∫
R
3/ n
rdr =
3
+2
n
3
+1
n
(1 − r / R )
(1 − r / R )
−
1 3
1 3
( + 2)
( n + 1)
2 n
R
R2
=
n2R2
( n + 3)( 2n + 3)
r =0
Substituting,
V avg =
2u max
R2
2n 2 u max
n2R2
=
= 0.8167u max
( n + 1)( 2n + 1) ( n + 1)(2n + 1)
and
α=
3
⎛ 2n 2 u max ⎞
2u max
⎟
⎜
R 2 ⎜⎝ (n + 1)(2n + 1) ⎟⎠
−3
(n + 1) 3 (2n + 1) 3
(7 + 1) 3 (2 × 7 + 1) 3
n2R2
= 1.06
=
= 4
(n + 3)(2n + 3) 4n (n + 3)(2n + 3) 4 × 7 4 (7 + 3)(2 × 7 + 3)
Discussion
Note that ignoring the kinetic energy correction factor results in an error of just 6% in this case in the
kinetic energy term (which may be small itself). Considering that the uncertainties in some terms are usually more that 6%,
we can usually ignore this correction factor in turbulent pipe flow analyses. However, for laminar pipe flow analyses, α is
equal to 2.0 for fully developed laminar pipe flow, and ignoring α may lead to significant errors.
5-54
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-86
Solution
A pump is pumping oil at a specified rate. The pressure rise of oil in the pump is measured, and the motor
efficiency is specified. The mechanical efficiency of the pump is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The elevation difference across the pump is negligible. 3 All the
losses in the pump are accounted for by the pump efficiency and thus hL = 0. 4 The kinetic energy correction factors are
given to be α1 = α2 = α = 1.05.
The density of oil is given to be ρ = 860 kg/m3.
Properties
Analysis
We take points 1 and 2 at the inlet and the exit of the pump, respectively. Noting that z1 = z2, the energy
equation for the pump reduces to
P1
V2
P
V2
+ α 1 1 + z1 + h pump, u = 2 + α 2 2 + z 2 + hturbine, e + h L
ρg
ρg
2g
2g
→
hpump, u =
P2 − P1 α (V 22 − V12 )
+
2g
ρg
where
18 kW
V1 =
2
0.1 m 3 /s
V
V
=
=
= 19.9 m/s
A1 πD12 / 4 π (0.08 m) 2 / 4
Pump
Motor
0.1 m 3 /s
V
V
=
=
= 8.84 m/s
V2 =
A2 πD 22 / 4 π (0.12 m) 2 / 4
Substituting, the useful pump head and the corresponding useful pumping power
are determined to be
hpump, u =
⎛ 1 kg ⋅ m/s 2
⎜
1N
(860 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
400,000 N/m 2
1
Oil
⎞ 1.05[ (8.84 m/s ) 2 − (19.9 m/s) 2 ]
⎟+
= 47.4 − 17.0 = 30.4 m
⎟
2(9.81 m/s 2 )
⎠
⎛
1 kN
W pump,u = ρVghpump, u = (860 kg/m 3 )(0.1 m 3 /s)(9.81 m/s 2 )(30.4 m)⎜⎜
1000
kg ⋅ m/s 2
⎝
⎞⎛ 1 kW ⎞
⎟⎜
⎟⎝ 1 kN ⋅ m/s ⎟⎠ = 25.6 kW
⎠
Then the shaft pumping power and the mechanical efficiency of the pump become
W pump,shaft = η motor W electric = (0.90)(35 kW) = 31.5 kW
W
25.6 kW
η pump = pump, u =
= 0.813 = 81.3%
Wpump, shaft 31.5 kW
Discussion
The overall efficiency of this pump/motor unit is the product of the mechanical and motor efficiencies,
which is 0.9 × 0.813 = 0.73.
5-55
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-87E
Solution
Water is pumped from a lake to a nearby pool by a pump with specified power and efficiency. The head
loss of the piping system and the mechanical power used to overcome it are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The elevation difference between the lake and the free surface of
the pool is constant. 3 All the losses in the pump are accounted for by the pump efficiency and thus hL represents the losses
in piping.
Properties
We take the density of water to be ρ = 62.4 lbm/ft3.
Analysis
The useful pumping power and the corresponding useful pumping head are
W pump, u = η pump W pump = (0.73)(12 hp) = 8.76 hp
h pump, u =
=
W pump, u
m g
=
W pump, u
ρVg
⎛ 32.2 lbm ⋅ ft/s 2
⎜
1 lbf
(62.4 lbm/ft 3 )(1.2 ft 3 /s)(32.2 ft/s 2 ) ⎜⎝
8.76 hp
⎞⎛ 550 lbf ⋅ ft/s ⎞
⎟⎜⎜
⎟⎟ = 64.3 ft
⎟
1 hp
⎠
⎠⎝
We choose points 1 and 2 at the free surfaces of the lake and the pool, respectively. Both points are open to the atmosphere
(P1 = P2 = Patm) and the velocities at both locations are negligible (V1 = V2 = 0). Then the energy equation for steady
incompressible flow through a control volume between these two points that includes the pump and the pipes reduces to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
ρg
ρg
2g
2g
Substituting, the head loss is determined to be
→
Pool
h L = h pump, u + z1 − z 2
2
h L = h pump, u − ( z 2 − z1 ) = 64.3 − 35 = 29.3 ft
Pump
35 ft
Lake
Then the power used to overcome it becomes
1
E mech loss, piping = ρVgh L
1 lbf
⎛
= (62.4 lbm/ft 3 )(1.2 ft 3 /s)(32.2 ft/s 2 )(29.3 ft )⎜
⎝ 32.2 lbm ⋅ ft/s 2
= 4.0 hp
1 hp
⎞⎛
⎞
⎟⎜
⎟
⎠⎝ 550 lbf ⋅ ft/s ⎠
Discussion
Note that the pump must raise the water an additional height of 29.3 ft to overcome the frictional losses in
pipes, which requires an additional useful pumping power of about 4 hp.
5-56
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-88
Solution
A fireboat is fighting fires by drawing sea water and discharging it through a nozzle. The head loss of the
system and the elevation of the nozzle are given. The shaft power input to the pump and the water discharge velocity are to
be determined.
Assumptions
1 The flow is steady and incompressible. 2 The effect of the kinetic energy correction factors is negligible,
Properties
The density of sea water is given to be ρ =1030 kg/m3.
α = 1.
2
Analysis
We take point 1 at the free surface of the sea and point
2 at the nozzle exit. Noting that P1 = P2 = Patm and V1 ≅ 0 (point 1 is at
the free surface; not at the pipe inlet), the energy equation for the
control volume between 1 and 2 that includes the pump and the piping
system reduces to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
ρg
ρg
2g
2g
4m
1
Fireboat
→
hpump, u = z 2 − z1 + α 2
V 22
+ hL
2g
where the water discharge velocity is
V2 =
0.1 m3 /s
V
V
=
=
= 50.93 m/s ≅ 50.9 m/s
A2 π D22 / 4 π (0.05 m) 2 / 4
Substituting, the useful pump head and the corresponding useful pump power are
determined to be
hpump, u = (4 m) + (1)
(50.93 m/s) 2
2(9.81 m/s 2 )
+ (3 m) = 139.2 m
⎛
1 kN
W pump,u = ρVghpump, u = (1030 kg/m 3 )(0.1 m 3 /s)(9.81 m/s 2 )(139.2 m)⎜
⎜ 1000 kg ⋅ m/s 2
⎝
= 140.7 kW
⎞⎛ 1 kW ⎞
⎟⎜
⎟⎝ 1 kN ⋅ m/s ⎟⎠
⎠
Then the required shaft power input to the pump becomes
W pump, shaft =
Discussion
W pump, u
η pump
=
140.7 kW
= 201 kW
0.70
Note that the pump power is used primarily to increase the kinetic energy of water.
5-57
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
Review Problems
5-89
Solution
A water tank open to the atmosphere is initially filled with water. The tank discharges to the atmosphere
through a long pipe connected to a valve. The initial discharge velocity from the tank and the time required to empty the
tank are to be determined.
Assumptions 1 The flow is incompressible. 2 The draining pipe is horizontal. 3 The tank is considered to be empty when
the water level drops to the center of the valve.
(a) Substituting the known quantities, the discharge velocity can be expressed as
Analysis
V=
2 gz
2 gz
=
= 0.1212 gz
1.5 + fL / D
1.5 + 0.015(100 m)/(0.10 m)
Then the initial discharge velocity becomes
V1 = 0.1212 gz1 = 0.1212(9.81 m/s 2 )(2 m) = 1.54 m/s
z
D0
D
where z is the water height relative to the center of the orifice at that time.
(b) The flow rate of water from the tank can be obtained by multiplying the
discharge velocity by the pipe cross-sectional area,
πD
V = ApipeV 2 =
0.1212 gz
4
Then the amount of water that flows through the pipe during a differential time interval dt is
2
πD
dV = Vdt =
0.1212 gz dt
(1)
4
which, from conservation of mass, must be equal to the decrease in the volume of water in the tank,
2
dV = Atan k (−dz ) = −
πD02
dz
(2)
4
where dz is the change in the water level in the tank during dt. (Note that dz is a negative quantity since the positive
direction of z is upwards. Therefore, we used –dz to get a positive quantity for the amount of water discharged). Setting
Eqs. (1) and (2) equal to each other and rearranging,
πD 2
4
0.1212 gz dt = −
πD02
4
dz → dt = −
D02
dz
D2
0.1212 gz
=−
D02
D 2 0.1212 g
z
− 12
dz
The last relation can be integrated easily since the variables are separated. Letting tf be the discharge time and integrating it
from t = 0 when z = z1 to t = tf when z = 0 (completely drained tank) gives
∫
tf
D02
dt = −
t =0
D
2
0.1212 g ∫
0
z
−1 / 2
z = z1
dz → t f = -
1
D02
D
2
0
z2
0.1212 g
1
2
2 D02
=
z1
D
2
0.1212 g
1
z12
Simplifying and substituting the values given, the draining time is determined to be
tf =
Discussion
2 D02
D
2
z1
2(10 m) 2
=
0.1212 g
(0.1 m) 2
2m
0.1212(9.81 m/s 2 )
= 25,940 s = 7.21 h
The draining time can be shortened considerably by installing a pump in the pipe.
5-58
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-90
Solution
The rate of accumulation of water in a pool and the rate of discharge are given. The rate supply of water to
the pool is to be determined.
Assumptions 1 Water is supplied and discharged steadily. 2 The rate of
evaporation of water is negligible. 3 No water is supplied or removed
through other means.
Analysis
The conservation of mass principle applied to the pool
requires that the rate of increase in the amount of water in the pool be equal
to the difference between the rate of supply of water and the rate of
discharge. That is,
dmpool
= m i − m e
dt
→
m i =
dmpool
dt
+ m e
→
dVpool Vi =
+ Ve
dt
since the density of water is constant and thus the conservation of mass is equivalent to conservation of volume. The rate of
discharge of water is
Ve = AeV e = (πD 2 /4)Ve = [π (0.05 m) 2 /4](5 m/s) = 0.00982 m 3 /s
The rate of accumulation of water in the pool is equal to the cross-section of the pool times the rate at which the water level
rises,
dV pool
dt
= Across-sectionV level = (3 m × 4 m)(0.015 m/min) = 0.18 m 3 /min = 0.00300 m 3 /s
Substituting, the rate at which water is supplied to the pool is determined to be
dVpool Vi =
+ Ve = 0.003 + 0.00982 = 0.01282 m3 /s ≅ 0.0128 m 3 /s
dt
Therefore, water is supplied at a rate of 0.01282 m3/s = 12.82 L/s.
Discussion
This is a very simple application of the conservation of mass equations.
5-91
Solution
A fluid is flowing in a circular pipe. A relation is to be obtained for the average fluid velocity in terms of
V(r), R, and r.
Analysis
Choosing a circular ring of area dA = 2πrdr as our differential area, the mass flow rate through a crosssectional area can be expressed as
∫
∫
dr
R
m = ρV (r )dA = ρV (r )2π r dr
0
A
R
r
Setting this equal to and solving for Vavg,
Vavg =
Discussion
2
R2
∫ V ( r ) r dr
R
0
If V were a function of both r and θ, we would also need to integrate with respect to θ.
5-59
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-92
Solution
Air is accelerated in a nozzle. The density of air at the nozzle exit is to be determined.
Assumptions
Flow through the nozzle is steady.
Properties
The density of air is given to be 4.18 kg/m3 at the inlet.
Analysis
1 = m
2 = m
. Then,
There is only one inlet and one exit, and thus m
m 1 = m 2
ρ 1 A1V1 = ρ 2 A2V 2
A V
120 m/s
ρ 2 = 1 1 ρ1 = 2
(4.18 kg/m 3 ) = 2.64 kg/m 3
380 m/s
A2 V 2
Discussion
nozzle.
1
AIR
2
Note that the density of air decreases considerably despite a decrease in the cross-sectional area of the
5-93
Solution
The air in a hospital room is to be replaced every 20 minutes. The minimum diameter of the duct is to be
determined if the air velocity is not to exceed a certain value.
Assumptions 1 The volume occupied by the furniture etc in the room is negligible. 2 The incoming conditioned air does
not mix with the air in the room.
Analysis
The volume of the room is
V = (6 m)(5 m)(4 m) = 120 m3
To empty this air in 20 min, the volume flow rate must be
Hospital Room
6×5×4 m
10 bulbs
120 m 3
V
=
= 0.10 m 3 /s
V =
Δt 20 × 60 s
If the mean velocity is 5 m/s, the diameter of the duct is
πD
V
V = AV =
4
2
→
D=
4V
=
πV
4(0.10 m 3 /s)
= 0.16 m
π (5 m/s)
Therefore, the diameter of the duct must be at least 0.16 m to ensure that the air in the room is exchanged completely within
20 min while the mean velocity does not exceed 5 m/s.
Discussion
This problem shows that engineering systems are sized to satisfy certain constraints imposed by certain
considerations.
5-60
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-94
Solution
Water discharges from the orifice at the bottom of a pressurized tank. The time it will take for half of the
water in the tank to be discharged and the water level after 10 s are to be determined.
Assumptions 1 The flow is incompressible, and the frictional effects are negligible. 2 The tank air pressure above the
water level is maintained constant.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
We take point 1 at the free surface of the tank, and point 2 at the exit of orifice. We take the positive
direction of z to be upwards with reference level at the orifice (z2 = 0). Fluid at point 2 is open to the atmosphere (and thus
P2 = Patm) and the velocity at the free surface is very low (V1 ≅ 0). Then,
P1 V12
P V2
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P1
P
V2
+ z1 = atm + 2
ρg
ρg 2 g
→
V2 = 2 gz1 + 2 P1,gage / ρ
or, V2 = 2 gz + 2 P1,gage / ρ where z is the water height in the tank at any time t. Water surface moves down as the tank
drains, and the value of z changes from H initially to 0 when the tank is emptied completely.
We denote the diameter of the orifice by D, and the diameter of the tank by Do. The flow rate of water from the
tank is obtained by multiplying the discharge velocity by the orifice cross-sectional area,
πD 2
V = AorificeV 2 =
2 gz + 2 P1,gage / ρ
4
Then the amount of water that flows through the orifice during a differential time interval dt is
πD 2
(1)
dV = Vdt =
2 gz + 2 P1,gage / ρ dt
4
which, from conservation of mass, must be equal to the decrease in the volume of water in the tank,
πD 2
dV = Atank (−dz ) = − 0 dz
(2)
4
where dz is the change in the water level in the tank during dt. (Note that dz is a negative quantity since the positive
direction of z is upwards. Therefore, we used –dz to get a positive quantity for the amount of water discharged). Setting
Eqs. (1) and (2) equal to each other and rearranging,
D2
πD 2
1
πD 2
dz
dt = − 02
2 gz + 2 P1,gage / ρ dt = − 0 dz
→
2 gz + 2 P1,gage / ρ
4
4
D
The last relation can be integrated since the variables are separated. Letting tf be the discharge time and integrating it from t
= 0 when z = z0 to t = t when z = z gives
1
2
2 z 0 2 P1, gage
2 z 2 P1, gage D0
Air, 450 kPa
+
−
+
= 2t
g
g
D
ρg 2
ρg 2
where
2 P1,gage
ρg
2
=
⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
(1000 kg/m )(9.81 m/s ) ⎜⎝
2(450 − 100) kN/m 2
3
2 2
⎞
⎟ = 7.274 s 2
⎟
⎠
Water tank
D0
z0= 3 m
The time for half of the water in the tank to be discharged (z = z0 /2) is
2(3 m)
9.81 m/s 2
+ 7.274 s 2 −
2(1.5 m)
9.81 m/s 2
2(3 m)
+ 7.274 s 2 =
(0.1 m) 2
(2 m) 2
D=10 cm
t
→ t = 22.0 s
2z
2
(0.1 m) 2
(10 s) → z =2.31 m
9.81 m/s 2
(2 m) 2
9.81 m/s 2
Discussion
Note that the discharging time is inversely proportional to the square of the orifice diameter. Therefore, the
discharging time can be reduced to one-fourth by doubling the diameter of the orifice.
(b) Water level after 10s is
+ 7.274 s 2 −
5-61
+ 7.274 s 2 =
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-95
Solution
Air flows through a pipe that consists of two sections at a specified rate. The differential height of a water
manometer placed between the two pipe sections is to be determined.
Assumptions 1The flow through the pipe is steady, incompressible, and irrotational with negligible friction (so that the
Bernoulli equation is applicable). 2 The losses in the reducing section are negligible. 3 The pressure difference across an air
column is negligible because of the low density of air, and thus the air column in the manometer can be ignored.
The density of air is given to be ρair = 1.20 kg/m3. We take the density of water to be ρw = 1000 kg/m3.
Properties
Analysis
We take points 1 and 2 along the centerline of the pipe over the two tubes of the manometer. Noting that z1
= z2 (or, the elevation effects are negligible for gases), the Bernoulli equation between points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P1 − P2 =
ρair (V22 − V12 )
2
(1)
We let the differential height of the water manometer be h. Then the pressure difference P2 – P1 can also be expressed as
P1 − P2 = ρ w gh
(2)
Combining Eqs. (1) and (2) and solving for h,
ρ air (V 22 − V12 )
2
= ρ w gh
→
ρ (V 2 − V12 )
V 2 − V12
h = air 2
= 2
2 gρ w
2 gρ w / ρ air
20 cm
Air
200 L/s
2
1
10 cm
Calculating the velocities and substituting,
V1 =
0.2 m 3 /s
V
V
=
=
= 6.37 m/s
A1 πD12 / 4 π (0.2 m) 2 / 4
V2 =
0.2 m 3 /s
V
V
=
=
= 25.5 m/s
A2 πD 22 / 4 π (0.1 m) 2 / 4
h=
(25.5 m/s) 2 − (6.37 m/s ) 2
2(9.81 m/s 2 )(1000 / 1.20)
h
Water
= 0.037 m = 3.7 cm
Therefore, the differential height of the water column will be 3.7 cm.
Discussion
Note that the differential height of the manometer is inversely proportional to the density of the manometer
fluid. Therefore, heavy fluids such as mercury are used when measuring large pressure differences.
5-62
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-96 [Also solved using EES on enclosed DVD]
Solution
Air flows through a horizontal duct of variable cross-section. For a given differential height of a water
manometer placed between the two pipe sections, the downstream velocity of air is to be determined, and an error analysis
is to be conducted.
Assumptions 1 The flow through the duct is steady, incompressible, and irrotational with negligible friction (so that the
Bernoulli equation is applicable). 2 The losses in this section of the duct are negligible. 3 The pressure difference across an
air column is negligible because of the low density of air, and thus the air column in the manometer can be ignored.
The gas constant of air is R = 0.287 kPa⋅m3/kg⋅K. We take the density of water to be ρw = 1000 kg/m3.
Properties
Analysis
We take points 1 and 2 along the centerline of the duct over the two tubes of the manometer. Noting that z1
= z2 (or, the elevation effects are negligible for gases) and V1 ≅ 0, the Bernoulli equation between points 1 and 2 gives
P1 V12
P V2
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
where
P1 − P2 = ρ w gh
and
ρ air =
→
P1
P V2
= 2 + 2
ρg ρg 2 g
→
V2 =
2( P1 − P2 )
ρ air
(1)
V1<<V2
P
100 kPa
=
= 1.17 kg/m 3
RT (0.287 kPa ⋅ m 3 /kg ⋅ K)(298 K)
Air
2
1
V2
Substituting into (1), the downstream velocity of air V2 is determined to be
V2 =
2 ρ w gh
ρ air
=
2(1000 kg/m 3 )(9.81 m/s 2 )(0.08 m)
1.17 kg/m 3
= 36.6 m/s
(2)
h
Water
Therefore, the velocity of air increases from a low level in the first section to 36.6
m/s in the second section.
Error Analysis We observe from Eq. (2) that the velocity is proportional to the square root of the differential height of the
manometer fluid. That is, V 2 = k h .
dh
Taking the differential: dV 2 = 12 k
h
dV 2 1 dh 1
dV2 dh
±2 mm
Dividing by V2:
= 2k
→
=
=
= ± 0.013
V2
2h 2 × 80 mm
V2
h k h
Therefore, the uncertainty in the velocity corresponding to an uncertainty of 2 mm in the differential height of water is
1.3%, which corresponds to 0.013×(36.6 m/s) = 0.5m/s. Then the discharge velocity can be expressed as
V2 = 36.6 ± 0.5 m/s
The error analysis does not include the effects of friction in the duct; the error due to frictional losses is
Discussion
most likely more severe than the error calculated here.
5-63
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-97
Solution
A tap is opened on the wall of a very large tank that contains air. The maximum flow rate of air through the
tap is to be determined, and the effect of a larger diameter lead section is to be assessed.
Assumptions Flow through the tap is steady, incompressible, and irrotational with negligible friction (so that the flow rate
is maximum, and the Bernoulli equation is applicable).
Properties
The gas constant of air is R = 0.287 kPa⋅m3/kg⋅K.
Analysis
The density of air in the tank is
ρ air =
P
102 kPa
=
= 1.21 kg/m 3
RT (0.287 kPa ⋅ m 3 /kg ⋅ K)(293 K)
We take point 1 in the tank, and point 2 at the exit of the tap along the same horizontal line. Noting that z1 = z2 (or, the
elevation effects are negligible for gases) and V1 ≅ 0, the Bernoulli equation between points 1 and 2 gives
P1 V12
P V2
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
→
P1
P V2
= 2 + 2
ρg ρg 2 g
→
V2 =
2( P1 − P2 )
ρ air
Substituting, the discharge velocity and the flow rate becomes
V2 =
2( P1 − P2 )
ρ air
=
2(102 − 100) kN/m ⎛ 1000 kg ⋅ m/s
⎜
⎜
1 kN
1.21 kg/m 3
⎝
2
2
⎞
⎟ = 57.5 m/s
⎟
⎠
πD 2
π (0.02 m)
V = AV 2 =
V2 =
(57.5 m/s) = 0.0181 m 3 /s
4
4
2
2
100 kPa
20°C
1
2 cm
2
Air
102 kPa
2 cm
4 cm
This is the maximum flow rate since it is determined by assuming
frictionless flow. The actual flow rate will be less.
Adding a 2-m long larger diameter lead section will have no effect on the flow rate since the flow is frictionless
(by using the Bernoulli equation, it can be shown that the velocity in this section increases, but the pressure decreases, and
there is a smaller pressure difference to drive the flow through the tab, with zero net effect on the discharge rate).
Discussion
If the pressure in the tank were 300 kPa, the flow is no longer incompressible, and thus the problem in that
case should be analyzed using compressible flow theory.
5-64
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-98
Solution
Water is flowing through a venturi meter with known diameters and measured pressures. The flow rate of
water is to be determined for the case of frictionless flow.
Assumptions 1 The flow through the venturi is steady, incompressible, and irrotational with negligible friction (so that the
Bernoulli equation is applicable). 2 The flow is horizontal so that elevation along the centerline is constant. 3 The pressure
is uniform at a given cross-section of the venturi meter (or the elevation effects on pressure measurement are negligible).
We take the density of water to be ρ = 1000 kg/m3.
Properties
Analysis
We take point 1 at the main flow section and point 2 at the throat along the centerline of the venturi meter.
Noting that z1 = z2, the application of the Bernoulli equation between points 1 and 2 gives
P1 V12
P V2
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
P1 − P2 = ρ
→
V 22 − V12
2
(1)
The flow is assumed to be incompressible and thus the density is constant. Then the conservation of mass relation for this
single stream steady flow device can be expressed as
V1 = V2 = V
→
A1V1 = A2V 2 = V
→ V1 =
V
A1
and
V2 =
Substituting into Eq. (1),
(V / A2 ) 2 − (V / A1 ) 2 ρV 2
=
P1 − P2 = ρ
2
2 A22
430 kPa
120 kPa
⎛ A22 ⎞
⎜1 −
⎟
⎜ A2 ⎟
1 ⎠
⎝
Solving for V gives the desired relation for the flow rate,
V = A2
V
(2)
A2
1
4 cm
7 cm
2
2( P1 − P2 )
(3)
ρ [1 − ( A2 / A1 ) 2 ]
The flow rate for the given case can be determined by substituting the given values into this relation to be
πD 2
V =
4
2
2( P1 − P2 )
ρ[1 − ( D 2 / D1 ) ]
4
=
π (0.04 m) 2
4
⎛ 1000 kg ⋅ m/s 2
⎜
1 kN
(1000 kg/m 3 )[1 - (4/7) 4 ] ⎜⎝
2(430 − 120) kN/m 2
⎞
⎟ = 0.0331 m 3 /s
⎟
⎠
Discussion
Venturi meters are commonly used as flow meters to measure the flow rate of gases and liquids by simply
measuring the pressure difference P1 - P2 by a manometer or pressure transducers. The actual flow rate will be less than the
value obtained from Eq. (3) because of the friction losses along the wall surfaces in actual flow. But this difference can be
as little as 1% in a well-designed venturi meter. The effects of deviation from the idealized Bernoulli flow can be accounted
for by expressing Eq. (3) as
V = C d A2
2( P1 − P2 )
ρ [1 − ( A2 / A1 ) 2 ]
where Cd is the venturi discharge coefficient whose value is less than 1 (it is as large as 0.99 for well-designed venturi
meters in certain ranges of flow). For Re > 105, the value of venturi discharge coefficient is usually greater than 0.96.
5-65
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-99E
Solution
A hose is connected to the bottom of a water tank open to the atmosphere. The hose is equipped with a
pump and a nozzle at the end. The maximum height to which the water stream could rise is to be determined.
Assumptions 1 The flow is incompressible with negligible friction. 2 The
friction between the water and air is negligible. 3 We take the head loss to be
zero (hL = 0) to determine the maximum rise of water jet.
Properties
2
We take the density of water to be 62.4 lbm/ft3.
Analysis
We take point 1 at the free surface of the tank, and point 2 at the
top of the water trajectory where V2 = 0. We take the reference level at the
bottom of the tank. Noting that the fluid at both points is open to the atmosphere
(and thus P1 = P2 = Patm) and that the fluid velocity at the free surface is very
low (V1 ≅ 0), the energy equation for a control volume between these two points
(in terms of heads) simplifies to
1
h
80 ft
P
V2
P1
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
→ z1 + h pump, u = z 2
ρg
ρg
2g
2g
where the useful pump head is
ΔPpump
⎛ 144 lbf/ft 2 ⎞⎛ 32.2 lbm ⋅ ft/s 2 ⎞
10 psi
⎟⎜
⎜
⎟ = 23.1 ft
=
hpump, u =
⎟
1 lbf
ρg
(62.4 lbm/ft 3 )(32.2 ft/s 2 ) ⎜⎝ 1 psi ⎟⎠⎜⎝
⎠
Substituting, the maximum height rise of water jet from the ground level is determined to be
z2 = z1 + hpump, u = 80 + 23.1 = 103.1 ft ≅ 103 ft
Discussion
The actual rise of water will be less because of the frictional effects between the water and the hose walls
and between the water jet and air.
5-100
Solution
A wind tunnel draws atmospheric air by a large fan. For a given air velocity, the pressure in the tunnel is to
be determined.
Assumptions 1The flow through the pipe is steady, incompressible, and irrotational with negligible friction (so that the
Bernoulli equation is applicable). 2 Air is and ideal gas.
Properties
The gas constant of air is R = 0.287 kPa⋅m3/kg⋅K.
Analysis
We take point 1 in atmospheric air before it enters the wind tunnel (and thus P1 = Patm and V1 ≅ 0), and point
2 in the wind tunnel. Noting that z1 = z2 (or, the elevation effects are negligible for gases), the Bernoulli equation between
points 1 and 2 gives
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
P2 = P1 −
ρV22
2
(1)
where
ρ=
Wind tunnel
1
20°C
101.3 kPa
P
101.3 kPa
=
= 1.205 kg/m 3
RT (0.287 kPa ⋅ m 3 /kg ⋅ K)(293 K)
80 m/s 2
Substituting, the pressure in the wind tunnel is determined to be
P2 = (101.3 kPa ) − (1.205 kg/m 3 )
(80 m/s) 2
2
⎞⎛ 1 kPa ⎞
⎛ 1N
⎟
⎜⎜
= 97.4 kPa
2 ⎟⎜
2⎟
1
kg
m/s
⋅
⎠⎝ 1000 N/m ⎠
⎝
Discussion
Note that the velocity in a wind tunnel increases at the expense of pressure. In reality, the pressure will be
even lower because of losses.
5-66
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-101
Solution
Water flows through the enlargement section of a horizontal pipe at a specified rate. For a given head loss,
the pressure change across the enlargement section is to be determined.
Assumptions 1 The flow through the pipe is steady and incompressible. 2 The pipe is horizontal. 3 The kinetic energy
correction factors are given to be α1 = α2 = α = 1.05.
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
We take points 1 and 2 at the inlet and exit of the enlargement section along the centerline of the pipe.
Noting that z1 = z2 , the energy equation for a control volume between these two points (in terms of heads) simplifies to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
2g
2g
ρg
ρg
where the inlet and exit velocities are
0.025 m 3 /s
V
V
=
=
= 8.84 m/s
V1 =
A1 πD12 / 4 π (0.06 m) 2 / 4
→
P2 − P1 = ρ
Water
0.025 m3/s
0.025 m 3 /s
V
V
=
=
= 2.63 m/s
V2 =
A2 πD 22 / 4 π (0.11 m) 2 / 4
α (V12 − V 22 )
2
− ρgh L
6 cm
1
2 11 cm
Substituting, the change in static pressure across the enlargement section is determined to be
⎛ 1.05[(8.84 m/s) 2 − (2.63 m/s) 2 ]
⎞⎛
1N
− (9.81 m/s 2 )(0.45 m) ⎟⎜
P2 − P1 = (1000 kg/m 3 )⎜
⎟⎜ 1 kg ⋅ m/s 2
⎜
2
⎝
⎠⎝
= 33.0 kPa
⎞⎛ 1 kPa ⎞
⎟⎜
⎟⎝ 1000 N/m 2 ⎟⎠
⎠
Therefore, the water pressure increases by 33 kPa across the enlargement section.
Discussion
Note that the pressure increases despite the head loss in the enlargement section. This is due to dynamic
pressure being converted to static pressure. But the total pressure (static + dynamic) decreases by 0.45 m (or 4.41 kPa) as a
result of frictional effects.
5-102
Solution
A water tank open to the atmosphere is initially filled with water. A sharp-edged orifice at the bottom drains
to the atmosphere through a long pipe with a specified head loss. The initial discharge velocity is to be determined.
Assumptions 1 The flow is incompressible. 2 The draining pipe is horizontal.
3 There are no pumps or turbines in the system. 4 The effect of the kinetic
energy correction factor is negligible, α = 1.
Analysis
We take point 1 at the free surface of the tank, and point 2 at the
exit of the pipe. We take the reference level at the centerline of the orifice (z2 =
0. Noting that the fluid at both points is open to the atmosphere (and thus P1 =
P2 = Patm) and that the fluid velocity at the free surface is very low (V1 ≅ 0), the
energy equation between these two points (in terms of heads) simplifies to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
2g
2g
ρg
ρg
→
z1 = α 2
1
Water
2m
100 m
V 22
+ hL
2g
10 cm
2
where α2 = 1 and the head loss is given to be hL = 1.5 m. Solving for V2 and substituting, the discharge velocity of water is
determined to be
V 2 = 2 g ( z1 − h L ) = 2(9.81 m/s 2 )(2 − 1.5) m = 3.13 m/s
Discussion
Note that this is the discharge velocity at the beginning, and the velocity will decrease as the water level in
the tank drops. The head loss in that case will change since it depends on velocity.
5-67
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-103
Solution
The previous problem is reconsidered. The effect of the tank height on the initial discharge velocity of water
from the completely filled tank as the tank height varies from 2 to 20 m in increments of 2 m at constant heat loss is to be
investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
g=9.81 "m/s2"
rho=1000 "kg/m3"
h_L=1.5 "m"
D=0.10 "m"
V_initial=SQRT(2*g*(z1-h_L)) "m/s"
16
14
Tank height,
z1, m
2
3
4
5
6
7
8
9
10
11
12
Discussion
Head Loss,
hL, m
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
Initial velocity
Vinitial, m/s
3.13
5.42
7.00
8.29
9.40
10.39
11.29
12.13
12.91
13.65
14.35
Vinitial, m/s
12
10
8
6
4
2
2
4
6
8
10
12
z1, m
The dependence of V on height is not linear, but rather V changes as the square root of z1.
5-68
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 5 Mass, Bernoulli, and Energy Equations
5-104
Solution
A water tank open to the atmosphere is initially filled with water. A sharp-edged orifice at the bottom drains
to the atmosphere through a long pipe equipped with a pump with a specified head loss. The required pump head to assure a
certain velocity is to be determined.
Assumptions 1 The flow is incompressible. 2 The draining pipe is horizontal. 3 The effect of the kinetic energy correction
factor is negligible, α = 1.
Analysis
We take point 1 at the free surface of the tank, and point 2 at the exit of the pipe. We take the reference
level at the centerline of the orifice (z2 = 0), and take the positive direction of z to be upwards. Noting that the fluid at both
points is open to the atmosphere (and thus P1 = P2 = Patm) and that the fluid velocity at the free surface is very low (V1 ≅ 0),
the energy equation between these two points (in terms of heads) simplifies to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
ρg
ρg
2g
2g
→
z1 + hpump, u = α 2
where α2 = 1 and the head loss is given to be hL = 1.5 m. Solving for hpump, u
and substituting, the required useful pump head is determined to be
hpump, u =
V 22
− z1 + h L =
2g
(6 m/s) 2
2(9.81 m/s 2 )
− (2 m) + (1.5 m) = 1.15 m
V 22
+ hL
2g
1
Water
2m
Pump
100 m
Discussion
Note that this is the required useful pump head at the beginning,
and it will need to be increased as the water level in the tank drops to make up
for the lost elevation head to maintain the constant discharge velocity.
2
10 cm
Design and Essay Problems
5-105 to 5-109
Solution
Students’ essays and designs should be unique and will differ from each other.
5-110
Solution
We are to evaluate a proposed modification to a wind turbine.
Analysis
Using the mass and the Bernoulli equations, it can be shown that this is a bad idea – the velocity at the exit
of nozzle is equal to the wind velocity. (The velocity at nozzle inlet is much lower). Sample calculation using EES using a
wind velocity of 10 m/s:
V0=10 "m/s"
rho=1.2 "kg/m3"
g=9.81 "m/s2"
A1=2 "m2"
A2=1 "m2"
A1*V1=A2*V2
P1/rho+V1^2/2=V2^2/2
m=rho*A1*V1
m*V0^2/2=m*V2^2/2
V0 =10 m/s
V2 =10 m/s
V1 =5 m/s
Results:
V1 = 5 m/s, V2 = 10 m/s, m = 12 kg/s (mass flow rate).
Discussion
Students’ approaches may be different, but they should come to the same conclusion – this does not help.
KJ
5-69
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications
by Çengel & Cimbala
CHAPTER 6
MOMENTUM ANALYSIS OF FLOW
SYSTEMS
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of The McGraw-Hill Companies, Inc.
(“McGraw-Hill”) and protected by copyright and other state and federal laws. By
opening and using this Manual the user agrees to the following restrictions, and if the
recipient does not agree to these restrictions, the Manual should be promptly returned
unopened to McGraw-Hill: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated
textbook. No other use or distribution of this Manual is permitted. This Manual
may not be sold and may not be distributed to or used by any student or other
third party. No part of this Manual may be reproduced, displayed or distributed
in any form or by any means, electronic or otherwise, without the prior written
permission of McGraw-Hill.
6-1
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
Newton’s Laws and Conservation of Momentum
6-1C
Solution
We are to express Newton’s three laws.
Analysis
Newton’s first law states that “a body at rest remains at rest, and a body in motion remains in motion at
the same velocity in a straight path when the net force acting on it is zero.” Therefore, a body tends to preserve its state
or inertia. Newton’s second law states that “the acceleration of a body is proportional to the net force acting on it and is
inversely proportional to its mass.” Newton’s third law states “when a body exerts a force on a second body, the second
body exerts an equal and opposite force on the first.”
Discussion
As we shall see in later chapters, the differential equation of fluid motion is based on Newton’s second law.
6-2C
Solution
We are to discuss if momentum is a vector, and its direction.
G
Analysis
Since momentum ( mV ) is the product of a vector (velocity) and a scalar (mass), momentum must be a
vector that points in the same direction as the velocity vector.
Discussion
equation.
6-3C
Solution
In the general case, we must solve three components of the linear momentum equation, since it is a vector
We are to discuss the conservation of momentum principle.
Analysis
The conservation of momentum principle is expressed as “the momentum of a system remains constant
when the net force acting on it is zero, and thus the momentum of such systems is conserved”. The momentum of a
body remains constant if the net force acting on it is zero.
Discussion
Momentum is not conserved in general, because when we apply a force, the momentum changes.
6-4C
Solution
We are to discuss Newton’s second law for rotating bodies.
Analysis
Newton’s second law of motion, also called the angular momentum equation, is expressed as “the rate of
change of the angular momentum of a body is equal to the net torque acting it.” For a non-rigid body with zero net
torque, the angular momentum remains constant, but the angular velocity changes in accordance with Iω = constant
where I is the moment of inertia of the body.
Discussion
Angular momentum is analogous to linear momentum in this way: Linear momentum does not change
unless a force acts on it. Angular momentum does not change unless a torque acts on it.
6-5C
Solution
We are to compare the angular momentum of two rotating bodies
Analysis
No. The two bodies do not necessarily have the same angular momentum. Two rigid bodies having the
same mass and angular speed may have different angular momentums unless they also have the same moment of inertia I.
Discussion
momentum.
The reason why flywheels have most of their mass at the outermost radius, is to maximize the angular
6-2
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
Linear Momentum Equation
6-6C
Solution
We are to discuss the importance of the RTT, and its relationship to the linear momentum equation.
Analysis
The relationship between the time rates of change of an extensive property for a system and for a
control volume is expressed by the Reynolds transport theorem (RTT), which provides the link between the system and
G
G
control volume concepts. The linear momentum equation is obtained by setting b = V and thus B = mV in the Reynolds
transport theorem.
Discussion
Newton’s second law applies directly to a system of fixed mass, but we use the RTT to transform from the
system formulation to the control volume formulation.
6-7C
Solution
We are to describe and discuss body forces and surface forces.
Analysis
The forces acting on the control volume consist of body forces that act throughout the entire body of the
control volume (such as gravity, electric, and magnetic forces) and surface forces that act on the control surface (such as
the pressure forces and reaction forces at points of contact). The net force acting on a control volume is the sum of all body
and surface forces. Fluid weight is a body force, and pressure is a surface force (acting per unit area).
Discussion
In a general fluid flow, the flow is influenced by both body and surface forces.
6-8C
Solution
We are to discuss surface forces in a control volume analysis.
Analysis
All surface forces arise as the control volume is isolated from its surroundings for analysis, and the
effect of any detached object is accounted for by a force at that location. We can minimize the number of surface forces
exposed by choosing the control volume (wisely) such that the forces that we are not interested in remain internal,
and thus they do not complicate the analysis. A well-chosen control volume exposes only the forces that are to be
determined (such as reaction forces) and a minimum number of other forces.
Discussion
There are many choices of control volume for a given problem. Although there are not really “wrong” and
“right” choices of control volume, there certainly are “wise” and “unwise” choices of control volume.
6-9C
Solution
We are to discuss the momentum flux correction factor, and its significance.
The momentum-flux correction factor β enables us to express the momentum flux in terms of the mass flow
G G G
G
ρV (V ⋅ n )dAc = β m V avg . The value of β is unity for uniform flow, such as a jet flow,
rate and mean flow velocity as
Analysis
∫
Ac
nearly unity for fully developed turbulent pipe flow (between 1.01 and 1.04), but about 1.3 for fully developed laminar pipe
flow. So it is significant and should be considered in laminar flow; it is often ignored in turbulent flow.
Discussion
Even though β is nearly unity for many turbulent flows, it is wise not to ignore it.
6-3
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-10C
Solution
Analysis
We are to discuss the momentum equation for steady one-D flow with no external forces.
The momentum equation for steady one-dimensional flow for the case of no external forces is
G
G
G
− ∑ β mV
∑ F = 0 = ∑ β mV
out
in
where the left hand side is the net force acting on the control volume (which is zero here), the first term on the right hand
side is the incoming momentum flux, and the second term on the right is the outgoing momentum flux by mass.
Discussion
This is a special simplified case of the more general momentum equation, since there are no forces. In this
case we can say that momentum is conserved.
6-11C
Solution
We are to explain why we can usually work with gage pressure rather than absolute pressure.
Analysis
In the application of the momentum equation, we can disregard the atmospheric pressure and work with
gage pressures only since the atmospheric pressure acts in all directions, and its effect cancels out in every direction.
Discussion
In some applications, it is better to use absolute pressure everywhere, but for most practical engineering
problems, it is simpler to use gage pressure everywhere, with no loss of accuracy.
6-12C
Solution
We are to compare the reaction force on two fire hoses.
Analysis
The fireman who holds the hose backwards so that the water makes a U-turn before being discharged
will experience a greater reaction force. This is because of the vector nature of the momentum equation. Specifically, the
inflow and outflow terms end up with the same sign (they add together) for the case with the U-turn, whereas they have
opposite signs (one partially cancels out the other) for the case without the U-turn.
Discussion
Direction is not an issue with the conservation of mass or energy equations, since they are scalar equations.
6-13C
Solution
We are to discuss if the upper limit of a rocket’s velocity is limited to V, its discharge velocity.
Analysis
No, V is not the upper limit to the rocket’s ultimate velocity. Without friction the rocket velocity will
continue to increase (i.e., it will continue to accelerate) as more gas is expelled out the nozzle.
Discussion
This is a simple application of Newton’s second law. As long as there is a force acting on the rocket, it will
continue to accelerate, regardless of how that force is generated.
6-14C
Solution
We are to describe how a helicopter can hover.
Analysis
A helicopter hovers because the strong downdraft of air, caused by the overhead propeller blades,
manifests a momentum in the air stream. This momentum must be countered by the helicopter lift force.
Discussion
In essence, the helicopter stays aloft by pushing down on the air with a net force equal to its weight.
6-4
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-15C
Solution
We are to discuss the power required for a helicopter to hover at various altitudes.
Analysis
Since the air density decreases, it requires more energy for a helicopter to hover at higher altitudes,
because more air must be forced into the downdraft by the helicopter blades to provide the same lift force. Therefore, it
takes more power for a helicopter to hover on the top of a high mountain than it does at sea level.
Discussion
This is consistent with the limiting case – if there were no air, the helicopter would not be able to hover at
all. There would be no air to push down.
6-16C
Solution
We are to discuss helicopter performance in summer versus winter.
Analysis
In winter the air is generally colder, and thus denser. Therefore, less air must be driven by the blades to
provide the same helicopter lift, requiring less power. Less energy is required in the winter.
Discussion
However, it is also harder for the blades to move through the denser cold air, so there is more torque
required of the engine in cold weather.
6-17C
Solution
We are to discuss if the force required to hold a plate stationary doubles when the jet velocity doubles.
Analysis
No, the force will not double. In fact, the force required to hold the plate against the horizontal water
stream will increase by a factor of 4 when the velocity is doubled since
F = m V = ( ρAV )V = ρAV 2
and thus the force is proportional to the square of the velocity.
Discussion
You can think of it this way: Since momentum flux is mass flow rate times velocity, a doubling of the
velocity doubles both the mass flow rate and the velocity, increasing the momentum flux by a factor of four.
6-18C
Solution
We are to discuss the acceleration of a cart hit by a water jet.
Analysis
The acceleration is not be constant since the force is not constant. The impulse force exerted by the
water on the plate is F = m V = ( ρAV )V = ρAV 2 , where V is the relative velocity between the water and the plate, which is
moving. The magnitude of the plate acceleration is thus a = F/m. But as the plate begins to move, V decreases, so the
acceleration must also decrease.
Discussion
It is the relative velocity of the water jet on the cart that contributes to the cart’s acceleration.
6-19C
Solution
We are to discuss the maximum possible velocity of a cart hit by a water jet.
Analysis
The maximum possible velocity for the plate is the velocity of the water jet. As long as the plate is
moving slower than the jet, the water exerts a force on the plate, which causes it to accelerate, until terminal jet velocity is
reached.
Discussion
Once the relative velocity is zero, the jet supplies no force to the cart, and thus it cannot accelerate further.
6-5
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-20
Solution
It is to be shown that the force exerted by a liquid jet of velocity V on a stationary nozzle is proportional to
2
V , or alternatively, to m 2 .
Assumptions 1 The flow is steady and incompressible. 2 The nozzle is given to be stationary. 3 The nozzle involves a
90° turn and thus the incoming and outgoing flow streams are normal to each other. 4 The water is discharged to the
atmosphere, and thus the gage pressure at the outlet is zero.
FRx
Analysis
We take the nozzle as the control volume, and the flow
direction at the outlet as the x axis. Note that the nozzle makes a 90°
turn, and thus it does not contribute to any pressure force or momentum
flux term at the inlet in the x direction. Noting that m = ρAV where A
is the nozzle outlet area and V is the average nozzle outlet velocity, the
momentum equation for steady one-dimensional flow in the x direction
reduces to
G
G
G
F=
βm V −
β m V
→ FRx = β m out V out = β m V
∑
∑
y
V
x
Nozzle
Liquid
∑
out
in
where FRx is the reaction force on the nozzle due to liquid jet at the nozzle outlet. Then,
m
m 2
=β
ρA
ρA
Therefore, the force exerted by a liquid jet of velocity V on this stationary nozzle is proportional to V2, or
alternatively, to m 2 .
m = ρAV
or FRx = βm V = β m
→ FRx = βm V = βρ AVV = βρAV 2
Discussion
If there were not a 90o turn, we would need to take into account the momentum flux and pressure
contributions at the inlet.
6-21
Solution
A water jet of velocity V impinges on a plate moving toward the water jet with velocity ½V. The force
required to move the plate towards the jet is to be determined in terms of F acting on the stationary plate.
Assumptions 1 The flow is steady and incompressible. 2 The plate is vertical and the jet is normal to plate. 3 The pressure
on both sides of the plate is atmospheric pressure (and thus its effect cancels out). 4 Fiction during motion is negligible. 5
There is no acceleration of the plate. 6 The water splashes off the sides of the plate in a plane normal to the jet. 6 Jet flow is
nearly uniform and thus the effect of the momentum-flux correction factor is negligible, β ≅ 1.
Analysis
We take the plate as the control volume. The relative velocity between the plate and the jet is V when the
plate is stationary, and 1.5V when the plate is moving with a velocity ½V towards the plate. Then the momentum equation
for steady one-dimensional flow in the horizontal direction reduces to
1/2V
G
G
G
F=
βm V −
β m V → − FR = −m i Vi → FR = m iVi
V
∑
∑
out
∑
in
Stationary plate: ( Vi = V and
Moving plate:
( Vi = 1.5V and
m i = ρAVi = ρAV ) → FR = ρAV 2 = F
Waterjet
m i = ρAVi = ρA(1.5V ) )
→ FR = ρA(1.5V ) 2 = 2.25 ρAV 2 = 2.25 F
Therefore, the force required to hold the plate stationary against the oncoming water jet becomes 2.25 times greater
when the jet velocity becomes 1.5 times greater.
Discussion
Note that when the plate is stationary, V is also the jet velocity. But if the plate moves toward the stream
with velocity ½V, then the relative velocity is 1.5V, and the amount of mass striking the plate (and falling off its sides) per
unit time also increases by 50%.
6-6
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-22
Solution
A 90° elbow deflects water upwards and discharges it to the atmosphere at a specified rate. The gage
pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place are to be determined.
Assumptions 1 The flow is steady, frictionless, incompressible, and irrotational (so that the Bernoulli equation is
applicable). 2 The weight of the elbow and the water in it is negligible. 3 The water is discharged to the atmosphere, and
thus the gage pressure at the outlet is zero. 4 The momentum-flux correction factor for each inlet and outlet is given to be β
= 1.03.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
(a) We take the elbow as the control volume, and designate the entrance by 1 and the outlet by 2. We also
designate the horizontal coordinate by x (with the direction of flow as being the positive direction) and the vertical
coordinate by z. The continuity equation for this one-inlet one-outlet steady flow system is m 1 = m 2 = m = 30 kg/s. Noting
that m = ρAV , the mean inlet and outlet velocities of water are
25 kg/s
m
m
=
=
= 3.18 m/s
2
ρA ρ (πD / 4) (1000 kg/m 3 )[π (0.1 m) 2 / 4]
Noting that V1 = V2 and P2 = Patm, the Bernoulli equation for a streamline going through the center of the reducing elbow is
expressed as
V1 = V 2 = V =
P V2
P1 V12
+
+ z1 = 2 + 2 + z2 → P1 − P2 = ρg ( z2 − z1 ) → P1, gage = ρg ( z2 − z1 )
ρg 2 g
ρg 2 g
Substituting,
⎛
1 kN
P1, gage = (1000 kg/m3 )( 9.81 m/s 2 ) ( 0.35 m ) ⎜
1000
kg ⋅ m/s 2
⎝
⎞
2
⎟ = 3.434 kN/m = 3.434 kPa ≅ 3.43 kPa
⎠
G
G
G
F=
βm V −
β m V . We let the x- and z(b) The momentum equation for steady one-dimensional flow is
∑
∑
out
∑
in
components of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. We also
use gage pressures to avoid dealing with the atmospheric pressure which acts on all surfaces. Then the momentum
equations along the x and y axes become
FRx + P1,gage A1 = 0 − βm (+V1 ) = − βm V
z
FRz = β m (+V 2 ) = β m V
x
Solving for FRx and FRz, and substituting the given values,
FRz
FRx = − βm V − P1, gage A1
⎛
1N
= −1.03(25 kg/s)(3.18 m/s)⎜⎜
2
⎝ 1 kg ⋅ m/s
= −109 N
⎞
⎟ − (3434 N/m 2 )[π (0.1 m) 2 / 4]
⎟
⎠
⎛
1N
FRy = βm V = 1.03(25 kg/s)(3.18 m/s)⎜⎜
1
kg
⋅ m/s 2
⎝
and
2
2
FR = FRx
+ FRy
= (−109) 2 + 81.9 2 = 136 N,
2
35 cm
FRx
Water
25 kg/s
1
⎞
⎟ = 81.9 N
⎟
⎠
θ = tan -1
FRy
FRx
= tan -1
81.9
= −37° = 143°
− 109
Discussion
Note that the magnitude of the anchoring force is 136 N, and its line of action makes 143° from the positive
x direction. Also, a negative value for FRx indicates the assumed direction is wrong, and should be reversed.
6-7
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-23
Solution
A 180° elbow forces the flow to make a U-turn and discharges it to the atmosphere at a specified rate. The
gage pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place are to be determined.
Assumptions 1 The flow is steady, frictionless, one-dimensional, incompressible, and irrotational (so that the Bernoulli
equation is applicable). 2 The weight of the elbow and the water in it is negligible. 3 The water is discharged to the
atmosphere, and thus the gage pressure at the outlet is zero. 4 The momentum-flux correction factor for each inlet and
outlet is given to be β = 1.03.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
(a) We take the elbow as the control volume, and designate the entrance by 1 and the outlet by 2. We also
designate the horizontal coordinate by x (with the direction of flow as being the positive direction) and the vertical
coordinate by z. The continuity equation for this one-inlet one-outlet steady flow system is m 1 = m 2 = m = 30 kg/s. Noting
that m = ρAV , the mean inlet and outlet velocities of water are
25 kg/s
m
m
=
=
= 3.18 m/s
2
ρA ρ (πD / 4) (1000 kg/m 3 )[π (0.1 m) 2 / 4]
Noting that V1 = V2 and P2 = Patm, the Bernoulli equation for a streamline going through the center of the reducing elbow is
expressed as
V1 = V 2 = V =
P V2
P1 V12
+
+ z1 = 2 + 2 + z2 → P1 − P2 = ρg ( z2 − z1 ) → P1, gage = ρg ( z2 − z1 )
ρg 2 g
ρg 2 g
Substituting,
⎛
1 kN
P1, gage = (1000 kg/m3 )( 9.81 m/s 2 ) ( 0.70 m ) ⎜
1000
kg ⋅ m/s 2
⎝
⎞
2
⎟ = 6.867 kN/m = 6.867 kPa ≅ 6.87 kPa
⎠
(b) The momentum equation for steady one-dimensional flow is
G
G
G
∑ F = ∑ βm V − ∑ βm V .
out
We let the x- and z-
in
components of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. We also
use gage pressures to avoid dealing with the atmospheric pressure which acts on all surfaces. Then the momentum
equations along the x and z axes become
FRx + P1,gage A1 = βm (−V 2 ) − β m (+V1 ) = −2 βm V
2
FRz = 0
z
Solving for FRx and substituting the given values,
FRx = −2 βm V − P1, gage A1
⎛
1N
= −2 × 1.03(25 kg/s)(3.18 m/s)⎜⎜
2
⎝ 1 kg ⋅ m/s
= −218 N
x
⎞
⎟ − (6867 N/m 2 )[π (0.1 m) 2 / 4]
⎟
⎠
and FR = FRx = - 218 N since the y-component of the anchoring force is zero.
Therefore, the anchoring force has a magnitude of 218 N and it acts in the negative
x direction.
Discussion
35 cm
FRz
FRx
Water
25 kg/s
1
Note that a negative value for FRx indicates the assumed direction is wrong, and should be reversed.
6-8
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-24E
Solution
A horizontal water jet strikes a vertical stationary plate normally at a specified velocity. For a given
anchoring force needed to hold the plate in place, the flow rate of water is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water splatters off the sides of the plate in a plane normal to
the jet. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the
atmospheric pressure which is disregarded since it acts on the entire control surface. 4 The vertical forces and momentum
fluxes are not considered since they have no effect on the horizontal reaction force. 5 Jet flow is nearly uniform and thus the
effect of the momentum-flux correction factor is negligible, β ≅ 1.
Properties
We take the density of water to be 62.4 lbm/ft3.
Analysis
We take the plate as the control volume such that it contains the entire plate and cuts through the water jet
and the support bar normally, and the direction of flow as the positive direction of x axis. The momentum equation for
steady one-dimensional flow in the x (flow) direction reduces in this case to
G
G
G
βm V −
βm V
→ − FRx = − m V1 → FR = m V1
F=
∑
∑
out
∑
in
We note that the reaction force acts in the opposite direction to flow, and we should not forget the negative sign for forces
and velocities in the negative x-direction. Solving for m and substituting the given values,
m =
FRx 350 lbf
=
30 ft/s
V1
⎛ 32.2 lbm ⋅ ft/s 2
⎜
⎜
1 lbf
⎝
⎞
⎟ = 376 lbm/s
⎟
⎠
FRx = 350 lbf
m
Then the volume flow rate becomes
1
Waterjet
376 lbm/s
m
V = =
= 6.02 ft 3 /s
ρ 62.4 lbm/ft 3
Therefore, the volume flow rate of water under stated assumptions must be 6.02 ft3/s.
Discussion
In reality, some water will be scattered back, and this will add to the reaction force of water. The flow rate in
that case will be less.
6-9
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-25
Solution
A reducing elbow deflects water upwards and discharges it to the atmosphere at a specified rate. The
anchoring force needed to hold the elbow in place is to be determined.
Assumptions 1 The flow is steady, frictionless, one-dimensional, incompressible, and irrotational (so that the Bernoulli
equation is applicable). 2 The weight of the elbow and the water in it is considered. 3 The water is discharged to the
atmosphere, and thus the gage pressure at the outlet is zero. 4 The momentum-flux correction factor for each inlet and
outlet is given to be β = 1.03.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
The weight of the elbow and the water in it is
25 cm2
W = mg = (50 kg)(9.81 m/s 2 ) = 490.5 N = 0.4905 kN
2
45°
We take the elbow as the control volume, and designate the
FRz
entrance by 1 and the outlet by 2. We also designate the
FRx
horizontal coordinate by x (with the direction of flow as being
the positive direction) and the vertical coordinate by z. The
150 m2
Water
continuity equation for this one-inlet one-outlet steady flow
30 kg/s
W
system is m 1 = m 2 = m = 30 kg/s. Noting that m = ρAV , the
1
inlet and outlet velocities of water are
30 kg/s
m
V1 =
=
= 2.0 m/s
ρA1 (1000 kg/m 3 )(0.0150 m 2 )
30 kg/s
m
=
= 12 m/s
V2 =
ρA2 (1000 kg/m 3 )(0.0025 m 2 )
Taking the center of the inlet cross section as the reference level (z1 = 0) and noting that P2 = Patm, the Bernoulli equation
for a streamline going through the center of the reducing elbow is expressed as
⎛ V 2 − V12
⎞
⎛ V 2 − V12
⎞
P1 V12
P V2
+
+ z1 = 2 + 2 + z2 → P1 − P2 = ρg ⎜⎜ 2
+ z2 − z1 ⎟⎟ → P1, gage = ρg ⎜⎜ 2
+ z2 ⎟⎟
ρg 2 g
ρg 2 g
⎝ 2g
⎠
⎝ 2g
⎠
Substituting,
⎛ (12 m/s) 2 − (2 m/s) 2
⎞⎛
⎞
1 kN
⎟ = 73.9 kN/m 2 = 73.9 kPa
P1, gage = (1000 kg/m3 )(9.81 m/s 2 )⎜
+ 0.4 ⎟⎜⎜
2
2⎟
⎜
⎟
2(9.81 m/s )
⎝
⎠⎝ 1000 kg ⋅ m/s ⎠
The momentum equation for steady one-dimensional flow is
G
G
G
∑ F = ∑ βm V − ∑ βm V . We let the x- and z- components
out
in
of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. We also use gage
pressures to avoid dealing with the atmospheric pressure which acts on all surfaces. Then the momentum equations along
the x and z axes become
FRx + P1,gage A1 = β m V 2 cos θ − βm V1 and FRz − W = βm V 2 sin θ
Solving for FRx and FRz, and substituting the given values,
⎛
⎞
1 kN
− 73.9 kN/m 2 )( 0.0150 m 2 )
FRx = β m (V2 cos θ − V )1 − P1, gage A1 = 1.03( 30 kg/s)[(12cos45°-2) m/s] ⎜
2 ⎟ (
⎝ 1000 kg ⋅ m/s ⎠
= −0.908 kN
⎛
⎞
1 kN
⎟ + 0.4905 kN = 0.753 kN
FRz = βm V 2 sin θ + W = 1.03(30 kg/s)(12sin45° m/s)⎜⎜
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠
F
0.753
2
2
+ FRz
= (−0.908) 2 + (0.753) 2 = 1.18 kN, θ = tan -1 Rz = tan -1
= −39.7°
FR = FRx
− 0.908
FRx
Discussion
Note that the magnitude of the anchoring force is 1.18 kN, and its line of action makes –39.7° from +x
direction. Negative value for FRx indicates the assumed direction is wrong.
6-10
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-26
Solution
A reducing elbow deflects water upwards and discharges it to the atmosphere at a specified rate. The
anchoring force needed to hold the elbow in place is to be determined.
Assumptions 1 The flow is steady, frictionless, one-dimensional, incompressible, and irrotational (so that the Bernoulli
equation is applicable). 2 The weight of the elbow and the water in it is considered. 3 The water is discharged to the
atmosphere, and thus the gage pressure at the outlet is zero. 4 The momentum-flux correction factor for each inlet and
outlet is given to be β = 1.03.
Properties
We take the density of water to be 1000 kg/m3.
110°
2
The weight of the elbow and the water in it is
Analysis
25 cm2
W = mg = (50 kg)(9.81 m/s 2 ) = 490.5 N = 0.4905 kN
We take the elbow as the control volume, and designate the entrance
by 1 and the outlet by 2. We also designate the horizontal coordinate
FRz
by x (with the direction of flow as being the positive direction) and
150 m2
the vertical coordinate by z. The continuity equation for this one-inlet
FRx
one-outlet steady flow system is m 1 = m 2 = m = 30 kg/s. Noting that
Water 1
W
m = ρAV , the inlet and outlet velocities of water are
30 kg/s
30 kg/s
m
V1 =
=
= 2.0 m/s
ρA1 (1000 kg/m 3 )(0.0150 m 2 )
30 kg/s
m
=
= 12 m/s
V2 =
ρA2 (1000 kg/m 3 )(0.0025 m 2 )
Taking the center of the inlet cross section as the reference level (z1 = 0) and noting that P2 = Patm, the Bernoulli equation
for a streamline going through the center of the reducing elbow is expressed as
⎞
⎛ V 2 − V12
⎞
⎛ V 2 − V12
P1 V12
P V2
+ z2 ⎟⎟
+
+ z1 = 2 + 2 + z2 → P1 − P2 = ρg ⎜⎜ 2
+ z2 − z1 ⎟⎟ → P1, gage = ρg ⎜⎜ 2
ρg 2 g
ρg 2 g
⎠
⎝ 2g
⎠
⎝ 2g
⎛ (12 m/s)2 − (2 m/s)2
or, P1, gage = (1000 kg/m3 )(9.81 m/s2 )⎜
⎜
⎝
2
2(9.81 m/s )
⎞⎛
⎞
1 kN
⎟ = 73.9 kN/m 2 = 73.9 kPa
+ 0.4 ⎟⎜⎜
⎟ 1000 kg ⋅ m/s 2 ⎟
⎠
⎠⎝
The momentum equation for steady one-dimensional flow is
G
G
G
∑ F = ∑ βm V − ∑ βm V . We let the x- and y- components
out
in
of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. We also use gage
pressures to avoid dealing with the atmospheric pressure which acts on all surfaces. Then the momentum equations along
the x and z axes become
FRx + P1,gage A1 = βm V 2 cos θ − βm V1
and
FRy − W = β m V 2 sin θ
Solving for FRx and FRz, and substituting the given values,
FRx = βm (V 2 cos θ − V1 ) − P1, gage A1
⎛
1 kN
= 1.03(30 kg/s)[(12cos110° - 2) m/s]⎜
⎜ 1000 kg ⋅ m/s 2
⎝
FRz
⎞
⎟ − (73.9 kN/m 2 )(0.0150 m 2 ) = −1.297 kN
⎟
⎠
⎞
⎛
1 kN
⎟ + 0.4905 kN = 0.8389 kN
= βm V 2 sin θ + W = 1.03(30 kg/s)(12sin110° m/s)⎜
⎜ 1000 kg ⋅ m/s 2 ⎟
⎠
⎝
2
2
FR = FRx
+ FRz
= (−1.297) 2 + 0.8389 2 = 1.54 kN
and
θ = tan -1
FRz
0.8389
= tan -1
= −32.9°
− 1.297
FRx
Discussion
Note that the magnitude of the anchoring force is 1.54 kN, and its line of action makes –32.9° from +x
direction. Negative value for FRx indicates assumed direction is wrong, and should be reversed.
6-11
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-27
Solution
Water accelerated by a nozzle strikes the back surface of a cart moving horizontally at a constant velocity.
The braking force and the power wasted by the brakes are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water splatters off the sides of the plate in all directions in
the plane of the back surface. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the
splattered water is the atmospheric pressure which is disregarded since it acts on all surfaces. 4 Fiction during motion is
negligible. 5 There is no acceleration of the cart. 7 The motions of the water jet and the cart are horizontal. 6 Jet flow is
nearly uniform and thus the effect of the momentum-flux correction factor is negligible, β ≅ 1.
Analysis
We take the cart as the control volume, and the
direction of flow as the positive direction of x axis. The relative
velocity between the cart and the jet is
V r = V jet − Vcart = 15 − 10 = 10 m/s
5 m/s
15 m/s
Waterjet
FRx
Therefore, we can view the cart as being stationary and the jet moving
with a velocity of 10 m/s. Noting that water leaves the nozzle at 15 m/s
and the corresponding mass flow rate relative to nozzle exit is 25 kg/s,
the mass flow rate of water striking the cart corresponding to a water jet
velocity of 10 m/s relative to the cart is
m r =
Vr
10 m/s
(25 kg/s) = 16.67 kg/s
m jet =
15 m/s
V jet
The momentum equation for steady one-dimensional flow in the x (flow) direction reduces in this case to
G
G
G
βm V −
βm V
→ FRx = −m i Vi → Fbrake = −m r V r
F=
∑
∑
out
∑
in
We note that the brake force acts in the opposite direction to flow, and we should not forget the negative sign for forces and
velocities in the negative x-direction. Substituting the given values,
⎛
1N
Fbrake = − m r V r = −(16.67 kg/s)( +10 m/s)⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞
⎟ = −166.7 N ≅ −167 N
⎟
⎠
The negative sign indicates that the braking force acts in the opposite direction to motion, as expected. Noting that work is
force times distance and the distance traveled by the cart per unit time is the cart velocity, the power wasted by the brakes is
⎛ 1W ⎞
W = FbrakeVcart = (166.7 N)(5 m/s)⎜
⎟ = 833 W
⎝ 1 N ⋅ m/s ⎠
Discussion
Note that the power wasted is equivalent to the maximum power that can be generated as the cart velocity is
maintained constant.
6-28
Solution
Water accelerated by a nozzle strikes the back surface of a cart moving horizontally. The acceleration of the
cart if the brakes fail is to be determined.
5 m/s
Analysis
The braking force was determined in previous problem
to be 167 N. When the brakes fail, this force will propel the cart
forward, and the acceleration will be
a=
F
167 N ⎛⎜ 1 kg ⋅ m/s 2
=
m cart 300 kg ⎜⎝
1N
15 m/s
300 kg
FRx
Waterjet
⎞
⎟ = 0.556 m/s 2
⎟
⎠
Discussion
This is the acceleration at the moment the brakes fail. The acceleration will decrease as the relative velocity
between the water jet and the cart (and thus the force) decreases.
6-12
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-29E
Solution
A water jet hits a stationary splitter, such that half of the flow is diverted upward at 45°, and the other half is
directed down. The force required to hold the splitter in place is to be determined.
Assumptions 1 The flow is steady and incompressible. 2
The water jet is exposed to the atmosphere, and thus the
pressure of the water jet before and after the split is the
atmospheric pressure which is disregarded since it acts on all
surfaces. 3 The gravitational effects are disregarded. 4 Jet flow
is nearly uniform and thus the effect of the momentum-flux
correction factor is negligible, β ≅ 1.
Properties
We take the density of water to be 62.4 lbm/ft3.
Analysis
The mass flow rate of water jet is
20 ft/s
FRz
100 ft3/s
45°
FRx
45°
m = ρV = (62.4 lbm/ft 3 )(100 ft 3 /s) = 6240 lbm/s
We take the splitting section of water jet, including the splitter as the control volume, and designate the entrance by 1 and
the outlet of either arm by 2 (both arms have the same velocity and mass flow rate). We also designate the horizontal
coordinate by x with the direction of flow as being the positive direction and the vertical coordinate by z.
G
G
G
The momentum equation for steady one-dimensional flow is
F=
βm V −
β m V . We let the x- and y-
∑
∑
out
∑
in
components of the anchoring force of the splitter be FRx and FRz, and assume them to be in the positive directions. Noting
that V2 = V1 = V and m 2 = 12 m , the momentum equations along the x and z axes become
FRx = 2( 12 m )V 2 cos θ − m V1 = m V (cos θ − 1)
FRz = 12 m (+V 2 sin θ ) + 12 m (−V 2 sin θ ) − 0 = 0
Substituting the given values,
1 lbf
⎛
⎞
FRx = ( 6240 lbm/s ) (20 ft/s)(cos45° - 1) ⎜
= − − 1135 lbf ≅ -1140 lbf
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
FRz = 0
The negative value for FRx indicates the assumed direction is wrong, and should be reversed. Therefore, a force of 1140 lbf
must be applied to the splitter in the opposite direction to flow to hold it in place. No holding force is necessary in the
vertical direction. This can also be concluded from the symmetry.
Discussion
In reality, the gravitational effects will cause the upper stream to slow down and the lower stream to speed
up after the split. But for short distances, these effects are indeed negligible.
6-13
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-30E
Solution
The previous problem is reconsidered. The effect of splitter angle on the force exerted on the splitter as the
half splitter angle varies from 0 to 180° in increments of 10° is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
g=32.2 "ft/s2"
rho=62.4 "lbm/ft3"
V_dot=100 "ft3/s"
V=20 "ft/s"
m_dot=rho*V_dot
F_R=-m_dot*V*(cos(theta)-1)/g "lbf"
8000
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
Discussion
m , lbm/s
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
6240
FR, lbf
0
59
234
519
907
1384
1938
2550
3203
3876
4549
5201
5814
6367
6845
7232
7518
7693
7752
7000
6000
5000
FR, lbf
θ, °
4000
3000
2000
1000
0
0
20
40
60
80
θ, °
100
120
140
160
180
The force rises from zero at θ = 0o to a maximum at θ = 180o, as expected, but the relationship is not linear.
6-14
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-31
Solution
A horizontal water jet impinges normally upon a vertical plate which is held on a frictionless track and is
initially stationary. The initial acceleration of the plate, the time it takes to reach a certain velocity, and the velocity at a
given time are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water always splatters in the plane of the retreating plate. 3
The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the atmospheric
pressure which is disregarded since it acts on all surfaces. 4 The tract is nearly frictionless, and thus fiction during motion is
negligible. 5 The motions of the water jet and the cart are horizontal. 6 The velocity of the jet relative to the plate remains
constant, Vr = Vjet = V. 7 Jet flow is nearly uniform and thus the effect of the momentum-flux correction factor is negligible,
β ≅ 1.
We take the density of water to be 1000 kg/m3.
Properties
Analysis
(a) We take the vertical plate on the frictionless track as the control volume, and the direction of flow as the
positive direction of x axis. The mass flow rate of water in the jet is
m = ρVA = (1000 kg/m 3 )(18 m/s)[π (0.05 m) 2 / 4] = 35.34 kg/s
The momentum equation for steady one-dimensional flow in the x (flow) direction reduces in this case to
G
G
G
βm V −
βm V
→ FRx = −m i Vi → FRx = −m V
F=
∑
∑
∑
out
in
where FRx is the reaction force required to hold the plate in place. When the plate is released, an equal and opposite impulse
force acts on the plate, which is determined to
⎛
1N
Fplate = − FRx = m V = (35.34 kg/s)(18 m/s)⎜⎜
1
kg
⋅ m/s 2
⎝
⎞
⎟ = 636 N
⎟
⎠
18 m/s
Then the initial acceleration of the plate becomes
a=
Fplate
m plate
636 N ⎛ 1 kg ⋅ m/s 2
⎜
=
1000 kg ⎜⎝ 1 N
1000 kg
⎞
⎟ = 0.636 m/s 2
⎟
⎠
Waterjet
This acceleration will remain constant during motion since the force acting
on the plate remains constant.
Frictionless track
FRx
(b) Noting that a = dV/dt = ΔV/Δt since the acceleration a is constant, the time it takes for the plate to reach a velocity of 9
m/s is
Δt =
ΔV plate
a
=
(9 − 0) m/s
0.636 m/s 2
= 14.2 s
(c) Noting that a = dV/dt and thus dV = adt and that the acceleration a is constant, the plate velocity in 20 s becomes
V plate = V0, plate + aΔt = 0 + (0.636 m/s 2 )(20 s) = 12.7 m/s
Discussion
The assumption that the relative velocity between the water jet and the plate remains constant is valid only
for the initial moments of motion when the plate velocity is low unless the water jet is moving with the plate at the same
velocity as the plate.
6-15
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-32
Solution
A 90° reducer elbow deflects water downwards into a smaller diameter pipe. The resultant force exerted on
the reducer by water is to be determined.
Assumptions 1 The flow is steady, frictionless, one-dimensional, incompressible, and irrotational (so that the Bernoulli
equation is applicable). 2 The weight of the elbow and the water in it is disregarded since the gravitational effects are
negligible. 3 The momentum-flux correction factor for each inlet and outlet is given to be β = 1.04.
Properties
We take the density of water to be 1000 kg/m3.
FRz
Analysis
We take the elbow as the control volume, and designate the
entrance by 1 and the outlet by 2. We also designate the horizontal coordinate by
x (with the direction of flow as being the positive direction) and the vertical
coordinate by z. The continuity equation for this one-inlet one-outlet steady flow
system is m 1 = m 2 = m = 353.4 kg/s. Noting that m = ρAV , the mass flow rate
of water and its outlet velocity are
30 cm
FRx
Water
5 m/s
m = ρV1 A1 = ρV1 (πD12 / 4) = (1000 kg/m 3 )(5 m/s)[π (0.3 m) 2 / 4] = 353.4 kg/s
353.4 kg/s
m
m
=
=
= 20 m/s
2
ρA2 ρπD 2 / 4 (1000 kg/m 3 )[π (0.15 m) 2 / 4]
The Bernoulli equation for a streamline going through the center of the reducing elbow is expressed as
V2 =
P V2
P1 V12
+
+ z1 = 2 + 2 + z2
ρg 2 g
ρg 2 g
→
15 cm
⎞
⎛ V 2 − V22
+ z1 − z2 ⎟⎟
P2 = P1 + ρg ⎜⎜ 1
⎠
⎝ 2g
Substituting, the gage pressure at the outlet becomes
⎛ (5 m/s)2 − (20 m/s)2
⎞⎛
⎞⎛ 1 kPa ⎞
1 kN
⎟⎜
P2 = (300 kPa) + (1000 kg/m3 )(9.81 m/s2 )⎜
+ 0.5 ⎟⎜⎜
⎟ = 117.4 kPa
2
2⎟
2
⎜
⎟
2(9.81 m/s )
⎝
⎠⎝ 1000 kg ⋅ m/s ⎠⎝ 1 kN/m ⎠
G
G
G
The momentum equation for steady one-dimensional flow is
F=
βm V −
β m V . We let the x- and z- components
∑
∑
out
∑
in
of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. Then the momentum
equations along the x and z axes become
FRx + P1,gage A1 = 0 − β m V1
FRz − P2,gage A2 = βm (−V 2 ) − 0
Note that we should not forget the negative sign for forces and velocities in the negative x or z direction. Solving for FRx
and FRz, and substituting the given values,
FRz
⎞
⎛
π (0.3 m) 2
1 kN
⎟ − (300 kN/m 2 )
FRx = − β m V1 − P1, gage A1 = −1.04(353.4 kg/s)(5 m/s)⎜⎜
= −23.0 kN
2 ⎟
4
⎝ 1000 kg ⋅ m/s ⎠
⎞
⎛
π (0.15 m) 2
1 kN
⎟ + (117.4 kN/m 2 )
= −5.28 kN and
= − β m V 2 + P2, gage A1 = −1.04(353.4 kg/s)(20 m/s)⎜⎜
2 ⎟
4
⎝ 1000 kg ⋅ m/s ⎠
2
2
FR = FRx
+ FRz
= (−23.0) 2 + (−5.28) 2 = 23.6 kN
θ = tan -1
FRz
− 5.28
= tan -1
= 12.9°
FRx
− 23.0
Discussion
The magnitude of the anchoring force is 23.6 kN, and its line of action makes 12.9° from +x direction.
Negative values for FRx and FRy indicate that the assumed directions are wrong, and should be reversed.
6-16
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-33 [Also solved using EES on enclosed DVD]
Solution
A wind turbine with a given span diameter and efficiency is subjected to steady winds. The power generated
and the horizontal force on the supporting mast of the turbine are to be determined.
Assumptions 1 The wind flow is steady and incompressible. 2 The efficiency of the turbine-generator is independent of
wind speed. 3 The frictional effects are negligible, and thus none of the incoming kinetic energy is converted to thermal
energy. 4 Wind flow is uniform and thus the momentum-flux correction factor is nearly unity, β ≅ 1.
Properties
The density of air is given to be 1.25 kg/m3.
Analysis
(a) The power potential of the wind is its kinetic
energy, which is V2/2 per unit mass, and m V 2 / 2 for a given mass
flow rate:
Wind
V1
2
1
D V2
⎛ 1 m/s ⎞
V1 = (25 km/h)⎜
⎟ = 6.94 m/s
⎝ 3.6 km/h ⎠
m = ρ1V1 A1 = ρ1V1
πD 2
4
= (1.25 kg/m 3 )(6.94 m/s)
2
V
(6.94 m/s)
W max = m ke1 = m 1 = (55,200 kg/s)
2
2
π (90 m) 2
4
2
= 55,200 kg/s
⎛
1 kN
⎜
⎜ 1000 kg ⋅ m/s 2
⎝
FR
⎞⎛ 1 kW ⎞
⎟⎜
⎟⎝ 1 kN ⋅ m/s ⎟⎠ = 1330 kW
⎠
Then the actual power produced becomes
W act = η wind turbineW max = (0.32)(1330 kW) = 426 kW
(b) The frictional effects are assumed to be negligible, and thus the portion of incoming kinetic energy not converted to
electric power leaves the wind turbine as outgoing kinetic energy. Therefore,
V2
V2
m ke 2 = m ke1 (1 − η wind turbine ) → m 2 = m 1 (1 − η wind turbine )
2
2
or
V 2 = V1 1 − η wind turbine = (6.94 m/s) 1 - 0.32 = 5.72 m/s
We choose the control volume around the wind turbine such that the wind is normal to the control surface at the inlet and
the outlet, and the entire control surface is at the atmospheric pressure. The momentum equation for steady one-dimensional
G
G
G
flow is
βm V −
β m V . Writing it along the x-direction (without forgetting the negative sign for forces and
F=
∑
∑
out
∑
in
velocities in the negative x-direction) and assuming the flow velocity through the turbine to be equal to the wind velocity
give
⎛
1 kN
FR = m V 2 − m V1 = m (V 2 − V1 ) = (55,200 kg/s)(5.72 - 6.94 m/s)⎜⎜
2
⎝ 1000 kg ⋅ m/s
⎞
⎟ = −67.3 kN
⎟
⎠
The negative sign indicates that the reaction force acts in the negative x direction, as expected.
Discussion
This force acts on top of the tower where the wind turbine is installed, and the bending moment it generates
at the bottom of the tower is obtained by multiplying this force by the tower height.
6-17
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-34E
Solution
A horizontal water jet strikes a curved plate, which deflects the water back to its original direction. The
force required to hold the plate against the water stream is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water jet
is exposed to the atmosphere, and thus the pressure of the water jet and
the splattered water is the atmospheric pressure, which is disregarded
since it acts on all surfaces. 3 Friction between the plate and the surface it
is on is negligible (or the friction force can be included in the required
force to hold the plate). 4 There is no splashing of water or the
deformation of the jet, and the reversed jet leaves horizontally at the same
velocity and flow rate. 5 Jet flow is nearly uniform and thus the
momentum-flux correction factor is nearly unity, β ≅ 1.
Properties
2
140 ft/s
Waterjet
1
FRx
3 in
140 ft/s
We take the density of water to be 62.4 lbm/ft3.
Analysis
We take the plate together with the curved water jet as the control volume, and designate the jet inlet by 1
and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of incoming flow as being the
positive direction). The continuity equation for this one-inlet one-outlet steady flow system is m 1 = m 2 = m where
m = ρVA = ρV [πD 2 / 4] = (62.4 lbm/ft 3 )(140 ft/s)[π (3 / 12 ft) 2 / 4] = 428.8 lbm/s
G
G
G
The momentum equation for steady one-dimensional flow is
F=
βm V −
β m V . Letting the reaction force to hold
∑
∑
out
∑
in
the plate be FRx and assuming it to be in the positive direction, the momentum equation along the x axis becomes
FRx = m (−V 2 ) − m (+V1 ) = −2m V
Substituting,
1 lbf
⎛
FRx = −2 ( 428.8 lbm/s ) (140 ft/s) ⎜
32.2
lbm ⋅ ft/s 2
⎝
⎞
⎟ = −3729 lbf ≅ −3730 lbf
⎠
Therefore, a force of 3730 lbf must be applied on the plate in the negative x direction to hold it in place.
Discussion
Note that a negative value for FRx indicates the assumed direction is wrong (as expected), and should be
reversed. Also, there is no need for an analysis in the vertical direction since the fluid streams are horizontal.
6-18
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-35E
Solution
A horizontal water jet strikes a bent plate, which deflects the water by 135° from its original direction. The
force required to hold the plate against the water stream is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure
of the water jet and the splattered water is the atmospheric pressure, which is disregarded since it acts on all surfaces. 3
Frictional and gravitational effects are negligible. 4 There is no splattering of water or the deformation of the jet, and the
reversed jet leaves horizontally at the same velocity and flow rate. 5 Jet flow is nearly uniform and thus the momentum-flux
correction factor is nearly unity, β ≅ 1.
Properties
We take the density of water to be 62.4 lbm/ft3.
Analysis
We take the plate together with the curved water jet as the control volume, and designate the jet inlet by 1
and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of incoming flow as being the
positive direction), and the vertical coordinate by z. The continuity equation for this one-inlet one-outlet steady flow system
is m 1 = m 2 = m where
m = ρVA = ρV [πD 2 / 4] = (62.4 lbm/ft 3 )(140 ft/s)[π (3 / 12 ft) 2 / 4] = 428.8 lbm/s
G
G
G
The momentum equation for steady one-dimensional flow is
F=
βm V −
β m V . We let the x- and z- components
∑
∑
∑
out
in
of the anchoring force of the plate be FRx and FRz, and assume them to be in the positive directions. Then the momentum
equations along the x and y axes become
FRx = m (−V 2 ) cos 45° − m (+V1 ) = −m V (1 + cos 45°)
FRz = m (+V 2 ) sin 45° = m V sin 45°
2
140 ft/s
1 lbf
⎛
⎞
FRx = −2(428.8 lbm/s)(140 ft/s)(1 + cos45°)⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
= −6365 lbf
1 lbf
⎛
⎞
= 1318 lbf
FRz = (428.8 lbm/s)(140 ft/s)sin45°⎜
2 ⎟
⎝ 32.2 lbm ⋅ ft/s ⎠
( −6365)
FRz
FRx
Substituting the given values,
and FR = FRx2 + FRz2 =
135°
2
+ 13182 = 6500 lbf ,
θ = tan -1
3 in
FRy
FRx
= tan -1
1
Waterjet
1318
= −11.7° = 168.3° ≅ 168°
−6365
Discussion
Note that the magnitude of the anchoring force is 6500 lbf, and its line of action is 168° from the positive x
direction. Also, a negative value for FRx indicates the assumed direction is wrong, and should be reversed.
6-19
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-36
Solution
Firemen are holding a nozzle at the end of a hose while trying to extinguish a fire. The average water outlet
velocity and the resistance force required of the firemen to hold the nozzle are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure
of the water jet is the atmospheric pressure, which is disregarded since it acts on all surfaces. 3 Gravitational effects and
vertical forces are disregarded since the horizontal resistance force is to be determined. 5 Jet flow is nearly uniform and
thus the momentum-flux correction factor can be taken to be unity, β ≅ 1.
Properties
We take the density of water to be 1000 kg/m3.
FRz
Analysis
(a) We take the nozzle and the horizontal
portion of the hose as the system such that water enters the
control volume vertically and outlets horizontally (this way
the pressure force and the momentum flux at the inlet are in
the vertical direction, with no contribution to the force balance
in the horizontal direction), and designate the entrance by 1
and the outlet by 2. We also designate the horizontal
coordinate by x (with the direction of flow as being the
positive direction). The average outlet velocity and the mass
flow rate of water are determined from
V=
FRx
5 m3/min
5 m 3 /min
V
V
=
=
= 1768 m/min = 29.5 m/s
A πD 2 / 4 π (0.06 m) 2 / 4
m = ρV = (1000 kg/m 3 )(5 m 3 /min) = 5000 kg/min = 83.3 kg/s
(b) The momentum equation for steady one-dimensional flow is
G
G
G
∑ F = ∑ βm V − ∑ βm V . We let horizontal force
out
in
applied by the firemen to the nozzle to hold it be FRx, and assume it to be in the positive x direction. Then the momentum
equation along the x direction gives
⎛ 1N ⎞
e − 0 = mV
= ( 83.3 kg/s ) (29.5 m/s) ⎜
FRx = mV
= 2457 N ≅ 2460 N
2 ⎟
⎝ 1kg ⋅ m/s ⎠
Therefore, the firemen must be able to resist a force of 2460 N to hold the nozzle in place.
Discussion
The force of 2460 N is equivalent to the weight of about 250 kg. That is, holding the nozzle requires the
strength of holding a weight of 250 kg, which cannot be done by a single person. This demonstrates why several firemen
are used to hold a hose with a high flow rate.
6-20
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-37
Solution
A horizontal jet of water with a given velocity strikes a flat plate that is moving in the same direction at a
specified velocity. The force that the water stream exerts against the plate is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water splatters in all directions in the plane of the plate. 3
The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the atmospheric
pressure, which is disregarded since it acts on all surfaces. 4 The vertical forces and momentum fluxes are not considered
since they have no effect on the horizontal force exerted on the plate. 5 The velocity of the plate, and the velocity of the
water jet relative to the plate, are constant. 6 Jet flow is nearly uniform and thus the momentum-flux correction factor can
be taken to be unity, β ≅ 1.
Properties
We take the density of water to be 1000 kg/m3.
10 m/s
Analysis
We take the plate as the control volume, and the flow
direction as the positive direction of x axis. The relative velocity
between the plate and the jet is
30 m/s
FRx
Waterjet
5 cm
V r = V jet − V plate = 30 − 10 = 20 m/s
Therefore, we can view the plate as being stationary and the jet to be
moving with a velocity of 20 m/s. The mass flow rate of water relative
to the plate [i.e., the flow rate at which water strikes the plate] is
πD 2
π (0.05 m)2
m r = ρVr A = ρVr
= (1000 kg/m3 )(20 m/s)
= 39.27 kg/s
4
4
The momentum equation for steady one-dimensional flow is
G
G
G
∑ F = ∑ βm V − ∑ βm V . We let the horizontal reaction
out
in
force applied to the plate in the negative x direction to counteract the impulse of the water jet be FRx. Then the momentum
equation along the x direction gives
⎞
⎛ 1N
⎟ = 785 N
− FRx = 0 − m Vi → FRx = m r V r = (39.27 kg/s)(20 m/s)⎜
⎜ 1kg ⋅ m/s 2 ⎟
⎠
⎝
Therefore, the water jet applies a force of 785 N on the plate in the direction of motion, and an equal and opposite force
must be applied on the plate if its velocity is to remain constant.
Discussion
Note that we used the relative velocity in the determination of the mass flow rate of water in the momentum
analysis since water will enter the control volume at this rate. (In the limiting case of the plate and the water jet moving at
the same velocity, the mass flow rate of water relative to the plate will be zero since no water will be able to strike the
plate).
6-21
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-38
Solution
The previous problem is reconsidered. The effect of the plate velocity on the force exerted on the plate as
the plate velocity varies from 0 to 30 m/s in increments of 3 m/s is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
rho=1000 "kg/m3"
D=0.05 "m"
V_jet=30 "m/s"
18 00
Ac=pi*D^2/4
V_r=V_jet-V_plate
m_dot=rho*Ac*V_r
F_R=m_dot*V_r "N"
16 00
14 00
Vplate, m/s
0
3
6
9
12
15
18
21
24
27
30
Vr, m/s
30
27
24
21
18
15
12
9
6
3
0
FR, N
1767
1431
1131
866
636
442
283
159
70.7
17.7
0
F R, N
12 00
10 00
800
600
400
200
0
0
5
10
15
20
Vplate, m /s
25
30
Discussion
When the plate velocity reaches 30 m/s, there is no relative motion between the jet and the plate; hence,
there can be no force acting.
6-22
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-39E
Solution
A fan moves air at sea level at a specified rate. The force required to hold the fan and the minimum power
input required for the fan are to be determined.
Assumptions 1 The flow of air is steady and incompressible. 2 Standard atmospheric conditions exist so that the pressure
at sea level is 1 atm. 3 Air leaves the fan at a uniform velocity at atmospheric pressure. 4 Air approaches the fan through a
large area at atmospheric pressure with negligible velocity. 5 The frictional effects are negligible, and thus the entire
mechanical power input is converted to kinetic energy of air (no conversion to thermal energy through frictional effects). 6
Wind flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, β ≅ 1.
Properties
The gas constant of air is R = 0.3704
psi⋅ft3/lbm⋅R. The standard atmospheric pressure at sea level is
1 atm = 14.7 psi.
2000 cfm
Analysis
(a) We take the control volume to be a
horizontal hyperbolic cylinder bounded by streamlines on the
sides with air entering through the large cross-section (section
1) and the fan located at the narrow cross-section at the end
(section 2), and let its centerline be the x axis. The density,
mass flow rate, and discharge velocity of air are
14.7 psi
P
ρ=
=
= 0.0749 lbm/ft 3
RT (0.3704 psi ⋅ ft 3 /lbm ⋅ R)(530 R)
m = ρV = (0.0749 lbm/ft 3 )(2000 ft 3/min) = 149.8 lbm/min = 2.50 lbm/s
V2 =
2000 ft 3 /min
V
V
=
=
= 636.6 ft/min = 10.6 ft/s
2
A2 πD 2 / 4
π (2 ft) 2 / 4
The momentum equation for steady one-dimensional flow is
G
Fan
2
1
24 in
G
G
∑ F = ∑ βm V − ∑ βm V . Letting the reaction force to hold
out
in
the fan be FRx and assuming it to be in the positive x (i.e., the flow) direction, the momentum equation along the x axis
becomes
1 lbf
⎛
⎞
FRx = m (V 2 ) − 0 = m V = (2.50 lbm/s)(10.6 ft/s)⎜
⎟ = 0.82 lbf
2
⎝ 32.2 lbm ⋅ ft/s ⎠
Therefore, a force of 0.82 lbf must be applied (through friction at the base, for example) to prevent the fan from moving in
the horizontal direction under the influence of this force.
(b) Noting that P1 = P2 = Patm and V1 ≅ 0, the energy equation for the selected control volume reduces to
⎞
⎛P V2
⎞
⎛P V2
m ⎜ 1 + 1 + gz1 ⎟ + W pump, u = m ⎜ 2 + 2 + gz 2 ⎟ + W turbine + E mech,loss →
⎟
⎜
⎟
⎜ρ
2
2
⎠
⎝ ρ
⎠
⎝
2
V
W fan, u = m 2
2
Substituting,
V2
(10.6 ft/s) 2 ⎛
1 lbf
W fan,u = m 2 = (2.50 lbm/s)
⎜
2
2
⎝ 32.2 lbm ⋅ ft/s 2
1W
⎞⎛
⎞
⎟⎜
⎟ = 5.91 W
0.73756
lbf
ft/s
⋅
⎠
⎠⎝
Therefore, a useful mechanical power of 5.91 W must be supplied to air. This is the minimum required power input required
for the fan.
Discussion
The actual power input to the fan will be larger than 5.91 W because of the fan inefficiency in converting
mechanical power to kinetic energy.
6-23
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-40
Solution
A helicopter hovers at sea level while being loaded. The volumetric air flow rate and the required power
input during unloaded hover, and the rpm and the required power input during loaded hover are to be determined.
Assumptions 1 The flow of air is steady and incompressible. 2 Air leaves the blades at a uniform velocity at atmospheric
pressure. 3 Air approaches the blades from the top through a large area at atmospheric pressure with negligible velocity. 4
The frictional effects are negligible, and thus the entire mechanical power input is converted to kinetic energy of air (no
conversion to thermal energy through frictional effects). 5 The change in air pressure with elevation is negligible because
of the low density of air. 6 There is no acceleration of the helicopter, and thus the lift generated is equal to the total weight.
7 Air flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, β ≅ 1.
The density of air is given to be 1.18 kg/m3.
Properties
Analysis
(a) We take the control volume to be a vertical hyperbolic cylinder bounded by streamlines on the sides
with air entering through the large cross-section (section 1) at the top and the fan located at the narrow cross-section at the
bottom (section 2), and let its centerline be the z axis with upwards being the positive direction.
G
G
G
The momentum equation for steady one-dimensional flow is
F=
βm V −
β m V . Noting that the only
∑
∑
out
∑
in
force acting on the control volume is the total weight W and it acts in the negative z direction, the momentum equation
along the z axis gives
1
W
W = m V 2 = ( ρAV 2 )V 2 = ρAV 22
V2 =
− W = m (−V 2 ) − 0
→
→
15 m
ρA
where A is the blade span area,
A = πD 2 / 4 = π (15 m) 2 / 4 = 176.7 m 2
2
Then the discharge velocity, volume flow rate, and the mass flow rate
of air in the unloaded mode become
V 2,unloaded =
m unloaded g
=
ρA
(10,000 kg)(9.81 m/s 2 )
(1.18 kg/m 3 )(176.7 m 2 )
= 21.7 m/s
Vunloaded = AV2 ,unloaded = (176.7 m 2 ) ( 21.7 m/s ) = 3834 m3 /s ≅ 3830 m3 /s
m unloaded = ρVunloaded = (1.18 kg/m 3 )(3834 m 3/s) = 4524 kg/s
Sea level
Load
15,000 kg
Noting that P1 = P2 = Patm, V1 ≅ 0, the elevation effects are negligible, and the frictional effects are disregarded, the energy
equation for the selected control volume reduces to
⎛P V2
⎞
⎛P V2
⎞
V2
m ⎜⎜ 1 + 1 + gz1 ⎟⎟ + W pump, u = m ⎜⎜ 2 + 2 + gz 2 ⎟⎟ + W turbine + E mech,loss → W fan, u = m 2
2
2
2
⎝ρ
⎠
⎝ ρ
⎠
Substituting,
2
21.7 m/s ) ⎛
⎛ V22 ⎞
⎞ ⎛ 1 kW ⎞
(
1 kN
= ( 4524 kg/s )
Wunloaded fan,u = ⎜ m
⎟
⎜
⎟ = 1065 kW ≅ 1070 kW
2 ⎟⎜
2
⎝ 1000 kg ⋅ m/s ⎠ ⎝ 1 kN ⋅ m/s ⎠
⎝ 2 ⎠ unloaded
(b) We now repeat the calculations for the loaded helicopter, whose mass is 10,000+15,000 = 25,000 kg:
m loaded g
(25,000 kg)(9.81 m/s 2 )
=
= 34.3 m/s
ρA
(1.18 kg/m 3 )(176.7 m 2 )
= ρVloaded = ρAV2, loaded = (1.18 kg/m 3 )(176.7 m 2 )(34.3 m/s) = 7152 kg/s
V 2,loaded =
m loaded
⎛ V2 ⎞
⎞ ⎛ 1 kW ⎞
(34.3 m/s) 2 ⎛
1 kN
Wloaded fan,u = ⎜ m 2 ⎟
= ( 7152 kg/s )
⎜
⎟ = 4207 kW ≅ 4210 kW
2 ⎟⎜
2
⎝ 1000 kg ⋅ m/s ⎠ ⎝ 1 kN ⋅ m/s ⎠
⎝ 2 ⎠loaded
Noting that the average flow velocity is proportional to the overhead blade rotational velocity, the rpm of the loaded
helicopter blades becomes
V 2,loaded
V 2,loaded
n
34.3
= loaded
→ n loaded =
(400 rpm) = 632 rpm
V 2 = kn →
n unloaded =
21.7
V 2, unloaded n unloaded
V 2, unloaded
Discussion
The actual power input to the helicopter blades will be considerably larger than the calculated power input
because of the fan inefficiency in converting mechanical power to kinetic energy.
6-24
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-41
Solution
A helicopter hovers on top of a high mountain where the air density considerably lower than that at sea
level. The blade rotational velocity to hover at the higher altitude and the percent increase in the required power input to
hover at high altitude relative to that at sea level are to be determined.
Assumptions 1 The flow of air is steady and incompressible. 2 The air leaves the blades at a uniform velocity at
atmospheric pressure. 3 Air approaches the blades from the top through a large area at atmospheric pressure with negligible
velocity. 4 The frictional effects are negligible, and thus the entire mechanical power input is converted to kinetic energy of
air. 5 The change in air pressure with elevation while hovering at a given location is negligible because of the low density
of air. 6 There is no acceleration of the helicopter, and thus the lift generated is equal to the total weight. 7 Air flow is
nearly uniform and thus the momentum-flux correction factor can be taken to be unity, β ≅ 1.
Properties
The density of air is given to be 1.18 kg/m3 at sea level, and 0.79 kg/m3 on top of the mountain.
Analysis
(a) We take the control volume to be a vertical hyperbolic cylinder bounded by streamlines on the sides
with air entering through the large cross-section (section 1) at the top and the fan located at the narrow cross-section at the
bottom (section 2), and let its centerline be the z axis with upwards being the positive direction.
G
G
G
The momentum equation for steady one-dimensional flow is
F=
βm V −
βm V . Noting that the only force
∑
∑
out
∑
in
acting on the control volume is the total weight W and it acts in the negative z direction, the momentum equation along the z
axis gives
W
− W = m (−V 2 ) − 0
→
→
W = m V 2 = ( ρAV 2 )V 2 = ρAV 22
V2 =
ρA
where A is the blade span area. Then for a given weight W, the ratio of discharge velocities becomes
V 2,mountain
V 2,sea
=
W / ρ mountain A
W / ρ sea A
=
ρ sea
1.18 kg/m 3
=
ρ mountain
= 1.222
0.79 kg/m 3
Noting that the average flow velocity is proportional to the overhead blade rotational velocity, the rpm of the helicopter
blades on top of the mountain becomes
n = kV2
→
n mountain V 2, mountain
=
n sea
V 2,sea
→
n mountain =
V 2, mountain
V 2,sea
n sea = 1.222(400 rpm) = 489 rpm
Noting that P1 = P2 = Patm, V1 ≅ 0, the elevation effect are negligible, and the frictional effects are disregarded, the energy
equation for the selected control volume reduces to
⎞
⎛P V2
⎞
⎛P V2
V2
m ⎜ 1 + 1 + gz1 ⎟ + W pump, u = m ⎜ 2 + 2 + gz 2 ⎟ + W turbine + E mech,loss → W fan, u = m 2
1
⎟
⎜ ρ
⎟
⎜ρ
2
2
2
⎠
⎝
⎠
⎝
or
V2
V2
V3
Wfan,u = m 2 = ρAV2 2 = ρA 2 =
2
2
2
3
1
2
⎛ W ⎞
⎟ =
⎟
⎝ ρA ⎠
ρA⎜⎜
1 .5
1
2
⎛W ⎞
⎟⎟
⎝ ρA ⎠
ρA⎜⎜
=
15 m
W 1 .5
2 ρA
2
Then the ratio of the required power input on top of the mountain to
that at sea level becomes
Wmountain fan,u 0.5W 1.5 / ρ mountain A
=
Wsea fan,u
0.5W 1.5 / ρsea A
ρsea
ρ mountain
=
1.18 kg/m3
= 1.222
0.79 kg/m3
Therefore, the required power input will increase by 22.2% on top of
the mountain relative to the sea level.
Sea level
Load
15,000 kg
Discussion
Note that both the rpm and the required power input to the helicopter are inversely proportional to the
square root of air density. Therefore, more power is required at higher elevations for the helicopter to operate because air is
less dense, and more air must be forced by the blades into the downdraft.
6-25
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-42
Solution
The flow rate in a channel is controlled by a sluice gate by raising or lowering a vertical plate. A relation for
the force acting on a sluice gate of width w for steady and uniform flow is to be developed.
Assumptions 1 The flow is steady, incompressible, frictionless, and uniform (and thus the Bernoulli equation is
applicable.) 2 Wall shear forces at surfaces are negligible. 3 The channel is exposed to the atmosphere, and thus the
pressure at free surfaces is the atmospheric pressure. 4 The flow is horizontal. 5 Water flow is nearly uniform and thus the
momentum-flux correction factor can be taken to be unity, β ≅ 1.
Analysis
We take point 1 at the free surface of the upstream flow before the gate and point 2 at the free surface of the
downstream flow after the gate. We also take the bottom surface of the channel as the reference level so that the elevations
of points 1 and 2 are y1 and y2, respectively. The application of the Bernoulli equation between points 1 and 2 gives
P V2
P1 V12
+
+ y1 = 2 + 2 + y 2
ρg 2 g
ρg 2 g
→
V 22 − V12 = 2 g( y1 − y 2 )
(1)
The flow is assumed to be incompressible and thus the density is constant. Then the conservation of mass relation for this
single stream steady flow device can be expressed as
V1 = V2 = V
→
A1V1 = A2V 2 = V
→ V1 =
V
V
=
A1 wy1
and
V2 =
V
V
=
(2)
A2 wy 2
Substituting into Eq. (1),
⎛ V
⎜
⎜ wy
⎝ 2
2
2
⎞ ⎛ V ⎞
2 g ( y1 − y 2 )
⎟ −⎜
⎟ = 2 g ( y1 − y 2 ) → V = w
⎟ ⎜ wy ⎟
1 / y 22 − 1 / y12
⎠ ⎝ 1⎠
2 g ( y1 − y 2 )
→ V = wy 2
1 − y 22 / y12
(3)
Substituting Eq. (3) into Eqs. (2) gives the following relations for velocities,
V1 =
y2
y1
2 g ( y1 − y 2 )
1−
y 22
/
y12
V2 =
and
2 g ( y1 − y 2 )
(4)
1 − y 22 / y12
We choose the control volume as the water body surrounded by the vertical cross-sections of the upstream and downstream
flows, free surfaces of water, the inner surface of the sluice gate, and the bottom surface of the channel. The momentum
G
G
G
equation for steady one-dimensional flow is
F=
βm V −
β m V . The force acting on the sluice gate FRx is
∑
∑
∑
out
in
horizontal since the wall shear at the surfaces is negligible, and it is equal and opposite to the force applied on water by the
sluice gate. Noting that the pressure force acting on a vertical surface is equal to the product of the pressure at the centroid
of the surface and the surface area, the momentum equation along the x direction gives
y ⎞
y ⎞
⎛
⎛
− FRx + P1 A1 − P2 A2 = m V 2 − m V1 → − FRx + ⎜ ρg 1 ⎟( wy1 ) − ⎜ ρg 2 ⎟( wy 2 ) = m (V 2 − V1 )
2
2 ⎠
⎝
⎠
⎝
Rearranging, the force acting on the sluice gate is determined to be
FRx = m (V1 − V 2 ) +
w
ρg ( y12 − y 22 )
2
1
(5)
FRx
where V1 and V2 are given in Eq. (4).
V1
Note that for y1 >> y2, Eq. (3) simplifies to
Discussion
V = y 2 w 2gy1 or V 2 = 2gy1 which is the Toricelli equation for
y1
2
Sluice gate
y2
V2
frictionless flow from a tank through a hole a distance y1 below the free
surface.
6-26
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-43
Solution
Water enters a centrifugal pump axially at a specified rate and velocity, and leaves in the normal direction
along the pump casing. The force acting on the shaft in the axial direction is to be determined.
Properties
We take the density of water to be 1000 kg/m3.
Assumptions 1 The flow is steady and incompressible. 2 The forces
acting on the piping system in the horizontal direction are negligible. 3
The atmospheric pressure is disregarded since it acts on all surfaces.
z
x
0.12 m3/s
7 m/s
Analysis
We take the pump as the control volume, and the inlet
direction of flow as the positive direction of x axis. The momentum
equation for steady one-dimensional flow in the x (flow) direction
reduces in this case to
G
G
G
F=
βm V −
βm V
→ − FRx = − m Vi → FRx = m Vi = ρVVi
∑
∑
mV
FRx
∑
out
in
Note that the reaction force acts in the opposite direction to flow, and we should not forget the negative sign for forces and
velocities in the negative x-direction. Substituting the given values,
⎛
1N
Fbrake = (1000 kg/m 3 )(0.12 m 3 /s)(7 m/s)⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞
⎟ = 840 N
⎟
⎠
Discussion
To find the total force acting on the shaft, we also need to do a force balance for the vertical direction, and
find the vertical component of the reaction force.
Angular Momentum Equation
6-44C
Solution
We are to discuss how the angular momentum equation is obtained from the RTT.
Analysis
The angular momentum equation is obtained by replacing B in the Reynolds transport theorem by the
G
G G
total angular momentum H sys , and b by the angular momentum per unit mass r × V .
Discussion
The RTT is a general equation that holds for any property B, either scalar or (as in this case) vector.
6-45C
Solution
We are to express the angular momentum equation for a specific (restricted) control volume.
G
G
G
G
Analysis
The angular momentum equation in this case is expressed as Iα = −r × m V where α is the angular
G
G
acceleration of the control volume, and r is the vector from the axis of rotation to any point on the line of action of F .
Discussion
This is a simplification of the more general angular momentum equation (many terms have dropped out).
6-46C
Solution
We are to express the angular momentum equation in scalar form about a specified axis.
Analysis
M =
∑
∑
out
The angular momentum equation about a given fixed axis in this case can be expressed in scalar form as
rm V −
rm V where r is the moment arm, V is the magnitude of the radial velocity, and m is the mass
∑
in
flow rate.
Discussion
This is a simplification of the more general angular momentum equation (many terms have dropped out).
6-27
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-47
Solution
Water is pumped through a piping section. The moment acting on the elbow for the cases of downward and
upward discharge is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water is discharged to the atmosphere, and thus the gage
pressure at the outlet is zero. 3 Effects of water falling down during upward discharge is disregarded. 4 Pipe outlet diameter
is small compared to the moment arm, and thus we use average values of radius and velocity at the outlet.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
We take the entire pipe as the control volume, and designate the
inlet by 1 and the outlet by 2. We also take the x and y coordinates as shown.
The control volume and the reference frame are fixed. The conservation of mass
equation for this one-inlet one-outlet steady flow system is m 1 = m 2 = m , and
V1 = V 2 = V since Ac = constant. The mass flow rate and the weight of the
horizontal section of the pipe are
r2 = 1 m
r1 = 2 m
MA
A
•
G
m V1
W
G
m V 2
m = ρAcV = (1000 kg/m 3 )[π (0.12 m) 2 / 4](4 m/s ) = 45.24 kg/s
⎛
1N
W = mg = (15 kg/m )(2 m )(9.81 m/s 2 )⎜⎜
2
⎝ 1 kg ⋅ m/s
⎞
⎟ = 294.3 N/m
⎟
⎠
(a) Downward discharge: To determine the moment acting on the pipe at point A, we need to take the moment of all
forces and momentum flows about that point. This is a steady and uniform flow problem, and all forces and momentum
flows are in the same plane. Therefore, the angular momentum equation in this case can be expressed as
M =
rm V −
rm V where r is the moment arm, all moments in the counterclockwise direction are positive, and all
∑
∑
out
∑
in
in the clockwise direction are negative.
The free body diagram of the pipe section is given in the figure. Noting that the moments of all forces and
momentum flows passing through point A are zero, the only force that will yield a moment about point A is the weight W of
the horizontal pipe section, and the only momentum flow that will yield a moment is the outlet stream (both are negative
since both moments are in the clockwise direction). Then the angular momentum equation about point A becomes
M A − r1W = −r2 m V 2
Solving for MA and substituting,
⎛
1N
M A = r1W − r2 m V 2 = (1 m)(294.3 N) - (2 m)(45.54 kg/s)(4 m/s)⎜⎜
⋅ m/s 2
1
kg
⎝
⎞
⎟ = −70.0 N ⋅ m
⎟
⎠
The negative sign indicates that the assumed direction for MA is wrong, and should be reversed. Therefore, a moment of 70
N⋅m acts at the stem of the pipe in the clockwise direction.
(b) Upward discharge: The moment due to discharge stream is positive in this case, and the moment acting on the pipe at
point A is
⎛
1N
M A = r1W + r2 m V 2 = (1 m)(294.3 N) + (2 m)(45.54 kg/s)(4 m/s)⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞
⎟ = 659 N ⋅ m
⎟
⎠
Discussion
Note direction of discharge can make a big difference in the moments applied on a piping system. This
problem also shows the importance of accounting for the moments of momentums of flow streams when performing
evaluating the stresses in pipe materials at critical cross-sections.
6-28
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-48E
Solution
A two-armed sprinkler is used to generate electric power. For a specified flow rate and rotational speed, the
power produced is to be determined.
Assumptions 1 The flow is cyclically steady (i.e., steady from a
frame of reference rotating with the sprinkler head). 2 The water is
discharged to the atmosphere, and thus the gage pressure at the nozzle
outlet is zero. 3 Generator losses and air drag of rotating components
are neglected. 4 The nozzle diameter is small compared to the moment
arm, and thus we use average values of radius and velocity at the outlet.
Electric
generator
ω
3
We take the density of water to be 62.4 lbm/ft .
Properties
Analysis
We take the disk that encloses the sprinkler arms as the
control volume, which is a stationary control volume. The conservation
of mass equation for this steady flow system is m 1 = m 2 = m . Noting
that the two nozzles are identical, we have m nozzle = m / 2 or
V
/ 2 since the density of water is constant. The average
= V
nozzle
V jet
total
jet outlet velocity relative to the nozzle is
⎛ 1 ft 3 ⎞
V
4 gal/s
⎜
⎟ = 392.2 ft/s
V jet = nozzle =
2
A jet
[π (0.5 / 12 ft) / 4] ⎜⎝ 7.480 gal ⎟⎠
V jet
m total = 8 gal/s
m nozzleV r
The angular and tangential velocities of the nozzles are
1 min ⎞
⎟ = 26.18 rad/s
⎝ 60 s ⎠
= rω = (2 ft)(26.18 rad/s) = 52.36 ft/s
ω = 2πn = 2π (250 rev/min)⎛⎜
V nozzle
Mshaft
•
The velocity of water jet relative to the control volume (or relative to a
fixed location on earth) is
V r = V jet − V nozzle = 392.2 − 52.36 = 339.8 ft/s
The
∑
angular momentum
M =
rm V −
rm V
∑
out
∑
equation can be expressed as
where
all
moments
in
the
r = 2 ft
m nozzleV r
in
counterclockwise direction are positive, and all in the clockwise
direction are negative. Then the angular momentum equation about the
axis of rotation becomes
− M shaft = −2rm nozzleV r
or
M shaft = rm total V r
Substituting, the torque transmitted through the shaft is determined to be
1 lbf
⎛
⎞
M shaft = rm total V r = (2 ft)(66.74 lbm/s)(339.8 ft/s)⎜
⎟ = 1409 lbf ⋅ ft
⎝ 32.2 lbm ⋅ ft/s 2 ⎠
since m total = ρVtotal = (62.4 lbm/ft 3 )(8 / 7.480 ft 3 /s ) = 66.74 lbm/s . Then the power generated becomes
1 kW
⎞
⎛
W = 2πn M shaft = ωM shaft = (26.18 rad/s)(1409 lbf ⋅ ft)⎜
⎟ = 50.0 kW
⎝ 737.56 lbf ⋅ ft/s ⎠
Therefore, this sprinkler-type turbine has the potential to produce 50 kW of power.
Discussion
This is, of course, the maximum possible power. The actual power generated would be much smaller than
this due to all the irreversible losses that we have ignored in this analysis.
6-29
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-49E
Solution
A two-armed sprinkler is used to generate electric power. For a specified flow rate and rotational speed, the
moment acting on the rotating head when the head is stuck is to be determined.
V jet
m nozzleV r
Electric
generator
Mshaft
ω
•
r = 2 ft
m nozzleV r
m total = 8 gal/s
V jet
Assumptions 1 The flow is uniform and steady. 2 The water is discharged to the atmosphere, and thus the gage pressure
at the nozzle outlet is zero. 3 The nozzle diameter is small compared to the moment arm, and thus we use average values of
radius and velocity at the outlet.
Properties
We take the density of water to be 62.4 lbm/ft3.
Analysis
We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control
volume. The conservation of mass equation for this steady flow system is m 1 = m 2 = m . Noting that the two nozzles are
identical, we have m nozzle = m / 2 or Vnozzle = Vtotal / 2 since the density of water is constant. The average jet outlet velocity
relative to the nozzle is
V jet =
⎛ 1 ft 3 ⎞
Vnozzle
4 gal/s
⎜
⎟ = 392.2 ft/s
=
A jet
[π (0.5 / 12 ft) 2 / 4] ⎜⎝ 7.480 gal ⎟⎠
The angular momentum equation can be expressed as
∑ M = ∑ rm V − ∑ rm V
out
where all moments in the
in
counterclockwise direction are positive, and all in the clockwise direction are negative. Then the angular momentum
equation about the axis of rotation becomes
− M shaft = −2rm nozzleV jet
or
M shaft = rm totalV jet
Substituting, the torque transmitted through the shaft is determined to be
1 lbf
⎛
M shaft = rm totalV jet = ( 2 ft )( 66.74 lbm/s )( 392.2 ft/s ) ⎜
2
⎝ 32.2 lbm ⋅ ft/s
⎞
⎟ = 1626 lbf ⋅ ft ≅ 1630 lbf ⋅ ft
⎠
since m total = ρVtotal = (62.4 lbm/ft 3 )(8 / 7.480 ft 3 /s ) = 66.74 lbm/s .
Discussion
When the sprinkler is stuck and thus the angular velocity is zero, the torque developed is maximum since
V nozzle = 0 and thus V r = V jet = 392.2 ft/s , giving M shaft, max = 1630 lbf ⋅ ft . But the power generated is zero in this case
since the shaft does not rotate.
6-30
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-50
Solution
A three-armed sprinkler is used to water a garden. For a specified flow rate and resistance torque, the
angular velocity of the sprinkler head is to be determined.
Assumptions 1 The flow is uniform and cyclically steady (i.e., steady from a frame of reference rotating with the
sprinkler head). 2 The water is discharged to the atmosphere, and thus the gage pressure at the nozzle outlet is zero. 3 Air
drag of rotating components are neglected. 4 The nozzle diameter is small compared to the moment arm, and thus we use
average values of radius and velocity at the outlet.
V jet
Properties
We take the density of water to be 1000 kg/m3 = 1 kg/L.
Electric
Analysis
We take the disk that encloses the sprinkler arms as the
generator
control volume, which is a stationary control volume. The conservation
of mass equation for this steady flow system is m 1 = m 2 = m . Noting
that the three nozzles are identical, we have m nozzle = m / 3 or
ω
V
/ 3 since the density of water is constant. The average jet
=V
nozzle
total
outlet velocity relative to the nozzle and the mass flow rate are
V jet =
⎛ 1m3 ⎞
Vnozzle
40 L/s
⎜
⎟ = 117.9 m/s
=
A jet
3[π (0.012 m) 2 / 4] ⎜⎝ 1000 L ⎟⎠
Vtotal = 40 L/s
m total = ρVtotal = (1 kg/L )(40 L/s ) = 40 kg/s
The angular momentum equation can be expressed as
M =
rm V −
rm V
∑
∑
out
∑
m nozzleV r
in
where all moments in the counterclockwise direction are positive, and
all in the clockwise direction are negative. Then the angular
momentum equation about the axis of rotation becomes
−T0 = −3rm nozzleV r
or
V jet
m nozzleV r
To = 50 N⋅m
T0 = rm total V r
•
r = 40 cm
Solving for the relative velocity Vr and substituting,
⎛ 1 kg ⋅ m/s 2
T0
50 N ⋅ m
⎜
Vr =
=
rm total (0.40 m)(40 kg/s) ⎜⎝
1N
⎞
⎟ = 3.1 m/s
⎟
⎠
Then the tangential and angular velocity of the nozzles become
V nozzle = V jet − V r = 117.9 − 3.1 = 114.8 m/s
m nozzleV r
Vnozzle 114.8 m/s
=
= 287 rad/s
0.4 m
r
ω 287 rad/s ⎛ 60 s ⎞
=
n =
⎜
⎟ = 2741 rpm ≅ 2740 rpm
2π
2π
⎝ 1 min ⎠
ω=
Therefore, this sprinkler will rotate at 2740 revolutions per minute (to three significant digits).
Discussion
The actual rotation rate will be somewhat lower than this due to air friction as the arms rotate.
6-31
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-51
Solution
A Pelton wheel is considered for power generation in a hydroelectric power plant. A relation is to be
obtained for power generation, and its numerical value is to be obtained.
Mshaft
ω
Vj - rω
r
Shaft
β
Vj - rω
Nozzle
rω
Vj
Assumptions 1 The flow is uniform and cyclically steady. 2 The water is discharged to the atmosphere, and thus the gage
pressure at the nozzle outlet is zero. 3 Friction and losses due to air drag of rotating components are neglected. 4 The nozzle
diameter is small compared to the moment arm, and thus we use average values of radius and velocity at the outlet.
Properties
We take the density of water to be 1000 kg/m3 = 1 kg/L.
Analysis
The tangential velocity of buckets corresponding to an angular velocity of ω = 2πn is V bucket = rω . Then
the relative velocity of the jet (relative to the bucket) becomes
V r = V j − V bucket = V j − rω
We take the imaginary disk that contains the Pelton wheel as the control volume. The inlet velocity of the fluid into this
control volume is Vr, and the component of outlet velocity normal to the moment arm is Vrcosβ. The angular momentum
equation can be expressed as
M =
rm V −
rm V where all moments in the counterclockwise direction are
∑
∑
∑
out
in
positive, and all in the clockwise direction are negative. Then the angular momentum equation about the axis of rotation
becomes
− M shaft = rm V r cos β − rm V r
or M shaft = rm V r (1 − cos β ) = rm (V j − rω )(1 − cos β )
Noting that W shaft = 2πn M shaft = ωM shaft and m = ρV , the shaft power output of a Pelton turbine becomes
W shaft = ρVrω (V j − rω )(1 − cos β )
which is the desired relation. For given values, the shaft power output is determined to be
⎛ 1 MW ⎞
W shaft = (1000 kg/m 3 )(10 m 3 /s )(2 m)(15.71 rad/s)(50 - 2 × 15.71 m/s)(1 - cos160°)⎜ 6
⎟ = 11.3 MW
⎝ 10 N ⋅ m/s ⎠
where
1 min ⎞
⎟ = 15.71 rad/s
⎝ 60 s ⎠
ω = 2πn = 2π (150 rev/min)⎛⎜
Discussion
The actual power will be somewhat lower than this due to air drag and friction. Note that this is the shaft
power; the electrical power generated by the generator connected to the shaft is be lower due to generator inefficiencies.
6-32
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-52
Solution
The previous problem is reconsidered. The effect of β on the power generation as β varies from 0° to 180°
is to be determined, and the fraction of power loss at 160° is to be assessed.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
rho=1000 "kg/m3"
r=2 "m"
V_dot=10 "m3/s"
V_jet=50 "m/s"
n_dot=150 "rpm"
omega=2*pi*n_dot/60
V_r=V_jet-r*omega
m_dot=rho*V_dot
W_dot_shaft=m_dot*omega*r*V_r*(1-cos(Beta))/1E6 "MW"
W_dot_max=m_dot*omega*r*V_r*2/1E6 "MW"
Efficiency=W_dot_shaft/W_dot_max
Angle,
β°
Max power,
Actual power,
Efficiency,
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
11.7
0.00
0.09
0.35
0.78
1.37
2.09
2.92
3.84
4.82
5.84
6.85
7.84
8.76
9.59
10.31
10.89
11.32
11.59
11.68
0.000
0.008
0.030
0.067
0.117
0.179
0.250
0.329
0.413
0.500
0.587
0.671
0.750
0.821
0.883
0.933
0.970
0.992
1.000
W max , MW
η
W shaft , MW
12
Wmax
10
Wshaft
8
Wshaft
6
4
2
0
0
Discussion
20
40
60
80
β, °
100
120
140
160
180
The efficiency of a Pelton wheel for β =160° is 0.97. Therefore, at this angle, only 3% of the power is lost.
6-33
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-53
Solution
A centrifugal blower is used to deliver atmospheric air. For a given angular speed and power input, the
volume flow rate of air is to be determined.
Impeller
shroud
G
V 2,t
b2
G
V1,t
r2
r2
b1
r1
r1
In
ω
ω
Shaft
Impeller
blade
Impeller
Impeller region
Assumptions 1 The flow is steady in the mean. 2 Irreversible losses are negligible. 3 The tangential components of air
velocity at the inlet and the outlet are said to be equal to the impeller velocity at respective locations.
The gas constant of air is 0.287 kPa⋅m3/kg⋅K. The density of air at 20°C and 95 kPa is
Properties
ρ=
95 kPa
P
=
= 1.130 kg/m 3
RT (0.287 kPa ⋅ m 3 /kg ⋅ K)(293 K)
Analysis
In the idealized case of the tangential fluid velocity being equal to the blade angular velocity both at the
inlet and the outlet, we have V1,t = ωr1 and V 2,t = ωr2 , and the torque is expressed as
Tshaft = m (r2V 2,t − r1V1,t ) = m ω (r22 − r12 ) = ρVω (r22 − r12 )
where the angular velocity is
1 min ⎞
⎟ = 83.78 rad/s
⎝ 60 s ⎠
ω = 2πn = 2π (800 rev/min)⎛⎜
Then the shaft power becomes
W shaft = ωTshaft = ρVω 2 (r22 − r12 )
Solving for V and substituting, the volume flow rate of air is determined to
V =
W shaft
ρω
2
( r22
− r12 )
=
⎛ 1 kg ⋅ m/s 2
⎜
1N
(1.130 kg/m 3 )(83.78 rad/s) 2 [(0.30 m) 2 - (0.15 m) 2 ] ⎜⎝
120 N ⋅ m/s
⎞
⎟ = 0.224 m 3 /s
⎟
⎠
The normal velocity components at the inlet and the outlet are
0.224 m 3 /s
V
=
= 3.90 m/s
2πr1b1 2π (0.15 m)(0.061 m)
0.224 m 3 /s
V
=
=
= 3.50 m/s
2πr2 b2 2π (0.30 m)(0.034 m)
V1,n =
V 2, n
Discussion
Note that the irreversible losses are not considered in this analysis. In reality, the flow rate and the normal
components of velocities will be smaller.
6-34
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-54
Solution
A centrifugal blower is used to deliver atmospheric air at a specified rate and angular speed. The minimum
power consumption of the blower is to be determined.
α2 = 50°
Impeller
shroud
G
V2
b2
b1
G
V1
r2
r2
r1
In
Shaft
r1
ω
ω
Impeller
blade
Impeller
Impeller region
Assumptions
1 The flow is steady in the mean. 2 Irreversible losses are negligible.
Properties
The density of air is given to be 1.25 kg/m3.
Analysis
outlet are
We take the impeller region as the control volume. The normal velocity components at the inlet and the
0.70 m 3 /s
V
=
= 6.793 m/s
2πr1b1 2π (0.20 m)(0.082 m)
0.70 m 3 /s
V
=
=
= 4.421 m/s
2πr2 b2 2π (0.45 m)(0.056 m)
V1,n =
V 2, n
The tangential components of absolute velocity are:
α1 = 0°:
V1,t = V1,n tan α 1 = 0
α2 = 60°:
V 2,t = V 2,n tan α 1 = (4.421 m/s ) tan 50° = 5.269 m/s
The angular velocity of the propeller is
1 min ⎞
ω = 2πn = 2π (700 rev/min)⎛⎜
⎟ = 73.30 rad/s
⎝ 60 s ⎠
m = ρV = (1.25 kg/m 3 )(0.7 m 3 /s) = 0.875 kg/s
Normal velocity components V1,n and V2,n as well pressure acting on the inner and outer circumferential areas pass through
the shaft center, and thus they do not contribute to torque. Only the tangential velocity components contribute to torque, and
the application of the angular momentum equation gives
⎛
1N
Tshaft = m (r2V 2,t − r1V1,t ) = (0.875 kg/s)[(0.45 m)(5.269 m/s) - 0]⎜⎜
⋅ m/s 2
1
kg
⎝
⎞
⎟ = 2.075 N ⋅ m
⎟
⎠
Then the shaft power becomes
⎛ 1W ⎞
W = ωTshaft = (73.30 rad/s)(2.075 N ⋅ m)⎜
⎟ = 152 W
⎝ 1 N ⋅ m/s ⎠
Discussion
The actual required shaft power is greater than this, due to the friction and other irreversibilities that we
have neglected in our analysis. Nevertheless, this is a good first approximation.
6-35
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-55
Solution
The previous problem is reconsidered. The effect of discharge angle α2 on the minimum power input
requirements as α2 varies from 0° to 85° in increments of 5° is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
rho=1.25 "kg/m3"
r1=0.20 "m"
b1=0.082 "m"
r2=0.45 "m"
b2=0.056 "m"
V_dot=0.70 "m3/s"
V1n=V_dot/(2*pi*r1*b1) "m/s"
V2n=V_dot/(2*pi*r2*b2) "m/s"
Alpha1=0
V1t=V1n*tan(Alpha1) "m/s"
V2t=V2n*tan(Alpha2) "m/s"
n_dot=700 "rpm"
omega=2*pi*n_dot/60 "rad/s"
m_dot=rho*V_dot "kg/s"
T_shaft=m_dot*(r2*V2t-r1*V1t) "Nm"
W_dot_shaft=omega*T_shaft "W"
1600
1400
1200
Wshaft, W
1000
800
600
400
200
0
0
10
20
30
40
α2
Angle,
α2°
V2,t,
m/s
Torque,
Tshaft, Nm
Shaft power,
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
0.00
0.39
0.78
1.18
1.61
2.06
2.55
3.10
3.71
4.42
5.27
6.31
7.66
9.48
12.15
16.50
25.07
50.53
0.00
0.15
0.31
0.47
0.63
0.81
1.01
1.22
1.46
1.74
2.07
2.49
3.02
3.73
4.78
6.50
9.87
19.90
0
11
23
34
46
60
74
89
107
128
152
182
221
274
351
476
724
1459
50
60
70
80
90
W shaft , W
Discussion
When α2 = 0, the shaft power is also zero as expected, since there is no turning at all. As α2 approaches 90o,
the required shaft power rises rapidly towards infinity. We can never reach α2 = 90o because this would mean zero flow
normal to the outlet, which is impossible.
6-36
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-56E
Solution
Water enters the impeller of a centrifugal pump radially at a specified flow rate and angular speed. The
torque applied to the impeller is to be determined.
Impeller
shroud
G
V 2,t
b2
G
V1
r2
r2
b1
r1
In
r1
Impeller
ω
ω
Shaft
Impeller
blade
Impeller region
Assumptions
1 The flow is steady in the mean. 2 Irreversible losses are negligible.
Properties
We take the density of water to be 62.4 lbm/ft3.
Analysis
Water enters the impeller normally, and thus V1,t = 0 . The tangential component of fluid velocity at the
outlet is given to be V 2,t = 180 ft/s . The inlet radius r1 is unknown, but the outlet radius is given to be r2 = 1 ft. The angular
velocity of the propeller is
ω = 2πn = 2π (500 rev/min)⎛⎜
1 min ⎞
⎟ = 52.36 rad/s
⎝ 60 s ⎠
The mass flow rate is
m = ρV = (62.4 lbm/ft 3 )(80/60 ft 3 /s) = 83.2 lbm/s
Only the tangential velocity components contribute to torque, and the application of the angular momentum equation gives
1 lbf
⎛
⎞
Tshaft = m (r2V 2,t − r1V1,t ) = (83.2 lbm/s)[(1 ft)(180 ft/s) - 0]⎜
⎟ = 465 lbf ⋅ ft
⎝ 32.2 lbm ⋅ ft/s 2 ⎠
Discussion
This shaft power input corresponding to this torque is
1 kW
⎛
⎞
W = 2πn Tshaft = ωTshaft = (52.36 rad/s)(465 lbf ⋅ ft)⎜
⎟ = 33.0 kW
⎝ 737.56 lbf ⋅ ft/s ⎠
Therefore, the minimum power input to this pump should be 33 kW.
6-37
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-57
Solution
A centrifugal pump is used to supply water at a specified rate and angular speed. The minimum power
consumption of the pump is to be determined.
Impeller
shroud
α2 = 60°
b2
G
V2
r2
b1
G
V1
r2
r1
In
r1
Shaft
ω
ω
Impeller
blade
Impeller
Impeller region
Assumptions
1 The flow is steady in the mean. 2 Irreversible losses are negligible.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
outlet are
We take the impeller region as the control volume. The normal velocity components at the inlet and the
0.15 m 3 /s
V
=
= 2.296 m/s
2πr1b1 2π (0.13 m)(0.080 m)
0.15 m 3 /s
V
=
=
= 2.274 m/s
2πr2 b2 2π (0.30 m)(0.035 m)
V1,n =
V 2, n
The tangential components of absolute velocity are:
α1 = 0°:
α2 = 60°:
V1,t = V1,n tan α 1 = 0
V 2,t = V 2,n tan α 1 = (2.274 m/s ) tan 60° = 3.938 m/s
The angular velocity of the propeller is
1 min ⎞
ω = 2πn = 2π (1200 rev/min)⎛⎜
⎟ = 125.7 rad/s
⎝ 60 s ⎠
m = ρV = (1000 kg/m 3 )(0.15 m 3 /s) = 150 kg/s
Normal velocity components V1,n and V2,n as well pressure acting on the inner and outer circumferential areas pass through
the shaft center, and thus they do not contribute to torque. Only the tangential velocity components contribute to torque, and
the application of the angular momentum equation gives
⎛
1 kN
Tshaft = m (r2V 2,t − r1V1,t ) = (150 kg/s)[(0.30 m)(3.938 m/s) - 0]⎜⎜
1000
kg ⋅ m/s 2
⎝
⎞
⎟ = 177.2 kN ⋅ m
⎟
⎠
Then the shaft power becomes
⎛ 1 kW ⎞
W = ωTshaft = (125.7 rad/s)(177.2 kN ⋅ m)⎜
⎟ = 22.3 kW
⎝ 1 kN ⋅ m/s ⎠
Discussion
larger.
Note that the irreversible losses are not considered in analysis. In reality, the required power input will be
6-38
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
Review Problems
6-58
Solution
Water is flowing into and discharging from a pipe U-section with a secondary discharge section normal to
return flow. Net x- and z- forces at the two flanges that connect the pipes are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The weight of the U-turn and the water in it is negligible. 4 The
momentum-flux correction factor for each inlet and outlet is given to be β = 1.03.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
The flow velocities of the 3 streams are
8 kg/s
3
m
m 1
30 kg/s
V1 = 1 =
=
= 15.3 m/s
ρA1 ρ (πD12 / 4) (1000 kg/m 3 )[π (0.05 m) 2 / 4]
V2 =
2
22 kg/s
m 2
m 2
22 kg/s
=
=
= 2.80 m/s
ρA2 ρ (πD 22 / 4) (1000 kg/m 3 )[π (0.10 m) 2 / 4]
FRz
1
m
m 3
8 kg/s
=
= 11.3 m/s
V3 = 3 =
ρA3 ρ (πD32 / 4 ) (1000 kg/m 3 )[π (0.03 m) 2 / 4]
FRx
30 kg/s
We take the entire U-section as the control volume. We designate the horizontal coordinate by x with the direction of
incoming flow as being the positive direction and the vertical coordinate by z. The momentum equation for steady oneG
G
G
βm V −
β m V . We let the x- and z- components of the anchoring force of the cone be FRx
F=
dimensional flow is
∑
∑
∑
out
in
and FRz, and assume them to be in the positive directions. Then the momentum equations along the x and z axes become
→ FRx = − P1 A1 − P2 A2 − β (m 2V 2 + m 1V1 )
FRx + P1 A1 + P2 A2 = β m 2 (−V 2 ) − βm 1V1
→ FRz = β m 3V 3
FRz + 0 = m 3V 3 - 0
Substituting the given values,
FRx = −[(200 − 100) kN/m 2 ]
π (0.05 m) 2
− [(150 − 100) kN/m 2 ]
π (0.10 m) 2
4
4
⎡
⎞⎤
⎛
⎞
⎛
1 kN
1 kN
⎟
⎟ + (30 kg/s)(15.3 m/s)⎜
− 1.03⎢(22 kg/s)(2.80 m/s)⎜
⎜ 1000 kg ⋅ m/s 2 ⎟⎥⎥
⎜ 1000 kg ⋅ m/s 2 ⎟
⎢⎣
⎠⎦
⎝
⎠
⎝
= −0.733 kN = −733 N
⎞
⎛
1N
⎟ = 93.1 N
FRz = 1.03(8 kg/s)(11.3 m/s)⎜⎜
2 ⎟
⎝ 1 kg ⋅ m/s ⎠
The negative value for FRx indicates the assumed direction is wrong, and should be reversed. Therefore, a force of 733 N
acts on the flanges in the opposite direction. A vertical force of 93.1 N acts on the flange in the vertical direction.
Discussion
To assess the significance of gravity forces, we estimate the weight of the weight of water in the U-turn and
compare it to the vertical force. Assuming the length of the U-turn to be 0.5 m and the average diameter to be 7.5 cm, the
mass of the water becomes
m = ρV = ρAL = ρ
πD 2
4
L = (1000 kg/m 3 )
π (0.075 m) 2
4
(0.5 m) = 2.2 kg
whose weight is 2.2×9.81 = 22 N, which is much less than 93.1, but still significant. Therefore, disregarding the
gravitational effects is a reasonable assumption if great accuracy is not required.
6-39
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-59
Solution
A fireman was hit by a nozzle held by a tripod with a rated holding force. The accident is to be investigated
by calculating the water velocity, the flow rate, and the nozzle velocity.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure
of the water jet is the atmospheric pressure, which is disregarded since it acts on all surfaces. 3 Gravitational effects and
vertical forces are disregarded since the horizontal resistance force is to be determined. 4 Jet flow is nearly uniform and
thus the momentum-flux correction factor can be taken to be unity, β ≅ 1.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
We take the nozzle and the horizontal portion of the hose as the system such that water enters the control
volume vertically and outlets horizontally (this way the pressure force and the momentum flux at the inlet are in the vertical
direction, with no contribution to the force balance in the horizontal direction, and designate the entrance by 1 and the
outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction).
G
G
G
F=
βm V −
β m V . We let the horizontal
The momentum equation for steady one-dimensional flow is
∑
∑
out
∑
in
force applied by the tripod to the nozzle to hold it be FRx, and assume it to be in the positive x direction. Then the
momentum equation along the x direction becomes
FRx = m Ve − 0 = m V = ρAVV = ρ
πD 2
4
V2
⎛ 1 kg ⋅ m/s 2
→ (1800 N)⎜
⎜
1N
⎝
2
⎞
⎟ = (1000 kg/m 3 ) π (0.05 m) V 2
⎟
4
⎠
Solving for the water outlet velocity gives V = 30.3 m/s. Then the water flow rate becomes
Nozzle
FRx
π (0.05 m)
πD
V = AV =
V=
(30.3 m/s) = 0.0595 m 3 /s
4
4
2
2
D = 5 cm
When the nozzle was released, its acceleration must have been
a nozzle =
F
m nozzle
=
1800 N ⎛⎜ 1 kg ⋅ m/s 2
10 kg ⎜⎝
1N
⎞
⎟ = 180 m/s 2
⎟
⎠
Tripod
Assuming the reaction force acting on the nozzle and thus its acceleration to remain constant, the time it takes for the
nozzle to travel 60 cm and the nozzle velocity at that moment were (note that both the distance x and the velocity V are zero
at time t = 0)
2(0.6 m)
2x
=
= 0.0816 s
x = 12 at 2 → t =
a
180 m/s 2
V = at = (180 m/s 2 )(0.0816 s) = 14.7 m/s
Thus we conclude that the nozzle hit the fireman with a velocity of 14.7 m/s.
Discussion
Engineering analyses such as this one are frequently used in accident reconstruction cases, and they often
form the basis for judgment in courts.
6-40
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-60
Solution
During landing of an airplane, the thrust reverser is lowered in the path of the exhaust jet, which deflects the
exhaust and provides braking. The thrust of the engine and the braking force produced after the thrust reverser is deployed
are to be determined.
Assumptions 1 The flow of exhaust gases is steady and one-dimensional. 2 The exhaust gas stream is exposed to the
atmosphere, and thus its pressure is the atmospheric pressure. 3 The velocity of exhaust gases remains constant during
reversing. 4 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, β ≅ 1.
(a) The thrust exerted on an airplane is simply the momentum flux of the combustion gases in the reverse
Analysis
direction,
⎛
1N
Thrust = m exVex = (18 kg/s)(250 m/s)⎜⎜
2
⎝ 1 kg ⋅ m/s
⎞
⎟ = 4500 N
⎟
⎠
(b) We take the thrust reverser as the control volume such that it cuts through both exhaust streams normally and the
connecting bars to the airplane, and the direction of airplane as the positive direction of x axis. The momentum equation for
steady one-dimensional flow in the x direction reduces to
G
G
G
βm V −
βm V
→ FRx = m (V )cos20° − m (−V ) → FRx = (1 + cos 20°)m Vi
F=
∑
∑
∑
out
in
Substituting, the reaction force is determined to be
FRx = (1 + cos 20°)(18 kg/s)(250 m/s) = 8729 N
The breaking force acting on the plane is equal and opposite to this force,
Fbreaking = 8729 N ≅ 8730 N
Therefore, a braking force of 8730 N develops in the opposite direction to flight.
α = 160°
160°
m V
Control
volume
250 m/s
m V
FRx
FRx
x
Discussion
This problem can be solved more generally by measuring the reversing angle from the direction of exhaust
gases (α = 0 when there is no reversing). When α < 90°, the reversed gases are discharged in the negative x direction, and
the momentum equation reduces to
FRx = m (−V )cosα − m (−V )
→
FRx = (1 − cos α )m Vi
This equation is also valid for α >90° since cos(180°-α) = - cosα. Using α = 160°, for example, gives
FRx = (1 − cos 160 )m Vi = (1 + cos 20)m Vi , which is identical to the solution above.
6-41
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-61
Solution
The previous problem is reconsidered. The effect of thrust reverser angle on the braking force exerted on
the airplane as the reverser angle varies from 0 (no reversing) to 180° (full reversing) in increments of 10° is to be
investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
V_jet=250 "m/s"
m_dot=18 "kg/s"
F_Rx=(1-cos(alpha))*m_dot*V_jet "N"
Braking force
Fbrake, N
9000
8000
0
68
271
603
1053
1607
2250
2961
3719
4500
5281
6039
6750
7393
7947
8397
8729
8932
9000
7000
6000
Fbrake, N
Reversing
angle,
α°
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
5000
4000
3000
2000
1000
0
0
20
40
60
80
α, °
100
120
140
160
180
Discussion
As expected, the braking force is zero when the angle is zero (no deflection), and maximum when the angle
is 180o (completely reversed). Of course, it is impossible to completely reverse the flow, since the jet exhaust cannot be
directed back into the engine.
6-42
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-62E
Solution
The rocket of a spacecraft is fired in the opposite direction to motion. The deceleration, the velocity change,
and the thrust are to be determined.
Assumptions 1 The flow of combustion gases is steady and one-dimensional during the firing period, but the flight of the
spacecraft is unsteady. 2 There are no external forces acting on the spacecraft, and the effect of pressure force at the nozzle
outlet is negligible. 3 The mass of discharged fuel is negligible relative to the mass of the spacecraft, and thus the spacecraft
may be treated as a solid body with a constant mass. 4 The nozzle is well-designed such that the effect of the momentumflux correction factor is negligible, and thus β ≅ 1.
Analysis
(a) We choose a reference frame in which the control
volume moves with the spacecraft. Then the velocities of fluid steams
become simply their relative velocities (relative to the moving body).
We take the direction of motion of the spacecraft as the positive
direction along the x axis. There are no external forces acting on the
spacecraft, and its mass is nearly constant. Therefore, the spacecraft can
be treated as a solid body with constant mass, and the momentum
equation in this case is
G
G
G
G
G
dVspace
d (mV ) CV
0=
+
β m V −
βm V → mspace
= −m f V f
dt
dt
out
in
∑
∑
18000 lbm
1500 ft/s
x
5000 ft/s
150 lbm/s
Noting that the motion is on a straight line and the discharged gases
move in the positive x direction (to slow down the spacecraft), we write
the momentum equation using magnitudes as
mspace
dVspace
dt
= −m f V f
→
dVspace
dt
=−
m f
mspace
Vf
Substituting, the deceleration of the spacecraft during the first 5 seconds is determined to be
dVspace
m f
150 lbm/s
a space =
=−
Vf = −
(5000 ft/s) = - 41.7 ft/s 2
dt
mspace
18,000 lbm
(b) Knowing the deceleration, which is constant, the velocity change of the spacecraft during the first 5 seconds is
determined from the definition of acceleration a space = dVspace / dt to be
dVspace = a space dt
→ ΔVspace = a space Δt = (-41.7 ft/s 2 )(5 s) = −209 ft/s
(c) The thrust exerted on the system is simply the momentum flux of the combustion gases in the reverse direction,
1 lbf
⎛
Thrust = FR = −m f V f = − (150 lbm/s )( 5000 ft/s ) ⎜
2
⎝ 32.2 lbm ⋅ ft/s
⎞
⎟ = −23, 290 lbf ≅ −23,300 lbf
⎠
Therefore, if this spacecraft were attached somewhere, it would exert a force of 23,300 lbf (equivalent to the weight of
23,300 lbm of mass on earth) to its support in the negative x direction.
Discussion
In Part (b) we approximate the deceleration as constant. However, since mass is lost from the spacecraft
during the time in which the jet is on, a more accurate solution would involve solving a differential equation. Here, the time
span is short, and the lost mass is likely negligible compared to the total mass of the spacecraft, so the more complicated
analysis is not necessary.
6-43
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-63
Solution
A horizontal water jet strikes a vertical stationary flat plate normally at a specified velocity. For a given
flow velocity, the anchoring force needed to hold the plate in place is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water splatters off the sides of the plate in a plane normal to
the jet. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the
atmospheric pressure which is disregarded since it acts on the entire control surface. 4 The vertical forces and momentum
fluxes are not considered since they have no effect on the horizontal reaction force. 5 Jet flow is nearly uniform and thus the
momentum-flux correction factor can be taken to be unity, β ≅ 1.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
We take the plate as the control volume such that it contains the entire plate and cuts through the water jet
and the support bar normally, and the direction of flow as the positive direction of x axis. We take the reaction force to be in
the negative x direction. The momentum equation for steady one-dimensional flow in the x (flow) direction reduces in this
case to
G
G
G
βm V −
βm V
→ − FRx = − m iVi → FRx = m V
F=
∑
∑
out
∑
in
We note that the reaction force acts in the opposite direction to flow, and we should not forget the negative sign for forces
and velocities in the negative x-direction. The mass flow rate of water is
π (0.05 m)
πD
m = ρV = ρAV = ρ
V = (1000 kg/m 3 )
(30 m/s) = 58.90 kg/s
4
4
2
2
30 m/s
FRx
Substituting, the reaction force is determined to be
FRx = ( 58.90 kg/s )( 30 m/s ) = 1767 N ≅ 1770 N
5 cm
Therefore, a force of 1770 N must be applied to the plate in the opposite direction
to the flow to hold it in place.
Discussion
In reality, some water may be scattered back, and this would add to the reaction force of water.
6-44
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-64
Solution
A water jet hits a stationary cone, such that the flow is diverted equally in all directions at 45°. The force
required to hold the cone in place against the water stream is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure
of the water jet before and after the split is the atmospheric pressure which is disregarded since it acts on all surfaces. 3 The
gravitational effects are disregarded. 4 Jet flow is nearly uniform and thus the momentum-flux correction factor can be
taken to be unity, β ≅ 1.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
The mass flow rate of water jet is
π (0.05 m)
πD
m = ρV = ρAV = ρ
V = (1000 kg/m 3 )
(30 m/s) = 58.90 kg/s
4
4
2
2
We take the diverting section of water jet, including the cone as the control volume, and designate the entrance by 1 and the
outlet after divergence by 2. We also designate the horizontal coordinate by x with the direction of flow as being the
positive direction and the vertical coordinate by y.
G
G
G
F=
βm V −
β m V . We let the x- and y- components
The momentum equation for steady one-dimensional flow is
∑
∑
out
∑
in
of the anchoring force of the cone be FRx and FRy, and assume them to be in the positive directions. Noting that V2 = V1 = V
and m 2 = m 1 = m , the momentum equations along the x and y axes become
FRx = m V 2 cos θ − m V1 = m V (cos θ − 1)
FRy = 0 (because of symmetry about x axis)
30 m/s
FRx
Substituting the given values,
⎛
1N
FRx = (58.90 kg/s)(30 m/s)(cos45° - 1)⎜⎜
2
⎝ 1 kg ⋅ m/s
= −518 N
⎞
⎟
⎟
⎠
5 cm
FRy = 0
The negative value for FRx indicates that the assumed direction is wrong, and should be reversed. Therefore, a force of 518
N must be applied to the cone in the opposite direction to flow to hold it in place. No holding force is necessary in the
vertical direction due to symmetry and neglecting gravitational effects.
Discussion
In reality, the gravitational effects will cause the upper part of flow to slow down and the lower part to
speed up after the split. But for short distances, these effects are negligible.
6-45
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-65
Solution
An ice skater is holding a flexible hose (essentially weightless) which directs a stream of water horizontally
at a specified velocity. The velocity and the distance traveled in 5 seconds, and the time it takes to move 5 m and the
velocity at that moment are to be determined.
Assumptions 1 Friction between the skates and ice is negligible. 2 The flow of water is steady and one-dimensional (but
the motion of skater is unsteady). 3 The ice skating arena is level, and the water jet is discharged horizontally. 4 The mass
of the hose and the water in it is negligible. 5 The skater is standing still initially at t = 0. 6 Jet flow is nearly uniform and
thus the momentum-flux correction factor can be taken to be unity, β ≅ 1.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
(a) The mass flow rate of water through the hose is
m = ρAV = ρ
πD 2
4
V = (1000 kg/m 3 )
π (0.02 m) 2
4
(10 m/s) = 3.14 kg/s
The thrust exerted on the skater by the water stream is simply the momentum flux of the water stream, and it acts in the
reverse direction,
⎛
1N
F = Thrust = m V = (3.14 kg/s)(10 m/s)⎜⎜
2
⎝ 1 kg ⋅ m/s
⎞
⎟ = 31.4 N (constant)
⎟
⎠
The acceleration of the skater is determined from Newton’s 2nd law of motion F = ma where m is the mass of the skater,
a=
F 31.4 N ⎛⎜ 1 kg ⋅ m/s 2
=
m 60 kg ⎜⎝
1N
⎞
⎟ = 0.523 m/s 2
⎟
⎠
Note that thrust and thus the acceleration of the skater is constant. The velocity of the skater and the distance traveled in 5 s
are
Vskater = at = (0.523 m/s 2 )(5 s) = 2.62 m/s
F
x = 12 at 2 = 12 (0.523 m/s 2 )(5 s) 2 = 6.54 m
10 m/s
(b) The time it will take to move 5 m and the velocity at that moment are
x = 12 at 2
→
t=
2x
=
a
2(5 m)
0.523 m/s 2
D=2 cm
Hose
= 4.4 s
Vskater = at = (0.523 m/s 2 )(4.4 s) = 2.3 m/s
Discussion
In reality, the velocity of the skater will be lower because of friction on ice and the resistance of the hose to
follow the skater. Also, in the β m V expressions, V is the fluid stream speed relative to a fixed point. Therefore, the correct
expression for thrust is F = m (V jet − Vskater ) , and the analysis above is valid only when the skater speed is low relative to
the jet speed. An exact analysis would result in a differential equation.
6-46
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-66
Solution
Indiana Jones is to ascend a building by building a platform, and mounting four water nozzles pointing
down at each corner. The minimum water jet velocity needed to raise the system, the time it will take to rise to the top of
the building and the velocity of the system at that moment, the additional rise when the water is shut off, and the time he
has to jump from the platform to the roof are to be determined.
Assumptions 1 The air resistance is negligible. 2 The flow of water is steady and one-dimensional (but the motion of
platform is unsteady). 3 The platform is still initially at t = 0. 4 Jet flow is nearly uniform and thus the momentum-flux
correction factor can be taken to be unity, β ≅ 1.
Properties
We take the density of water to be 1000 kg/m3.
(a) The total mass flow rate of water through the 4 hoses and the total weight of the platform are
π (0.05 m) 2
πD 2
m = ρAV = 4 ρ
V = 4(1000 kg/m 3 )
(15 m/s) = 118 kg/s
4
4
⎛
⎞
1N
⎟ = 1472 N
W = mg = (150 kg)(9.81 m/s 2 )⎜
⎜ 1 kg ⋅ m/s 2 ⎟
⎝
⎠
We take the platform as the system. The momentum equation for steady one-dimensional flow is
G
G
G
βm V −
β m V . The minimum water jet velocity needed to raise the platform is determined by setting the net
F=
Analysis
∑
∑
out
∑
in
force acting on the platform equal to zero,
− W = m (−V min ) − 0
→
W = m V min = ρAV min V min = 4 ρ
πD 2
4
2
V min
Solving for Vmin and substituting,
Vmin =
W
=
ρπD 2
⎛ 1kg ⋅ m/s 2 ⎞
1472 N
⎜
⎟ = 13.7 m/s
⎟
1N
(1000 kg/m 3 )π (0.05 m) 2 ⎜⎝
⎠
(b) We let the vertical reaction force (assumed upwards) acting on the platform be FRz. Then the momentum equation in the
vertical direction becomes
⎛ 1kg ⋅ m/s 2 ⎞
⎟ = −298 N
FRz − W = m (−V ) − 0 = m V → FRz = W − m V = (1472 N) - (118 kg/s)(15 m/s)⎜⎜
⎟
1N
⎠
⎝
The upward thrust acting on the platform is equal and opposite to this reaction force, and thus F = 298 N. Then the
acceleration and the ascending time to rise 10 m and the velocity at that moment become
a=
F 298 N ⎛⎜ 1 kg ⋅ m/s 2
=
m 150 kg ⎜⎝
1N
x = 12 at 2
→ t=
⎞
⎟ = 2.0 m/s 2
⎟
⎠
2(10 m)
2x
=
= 3.2 s
a
2 m/s 2
z
FRy
x
V = at = (2 m/s 2 )(3.2 s) = 6.4 m/s
(c) When water is shut off at 10 m height (where the velocity is 6.4 m/s), the
platform will decelerate under the influence of gravity, and the time it takes to
come to a stop and the additional rise above 10 m become
V = V0 − gt = 0 → t =
D=5 cm
15 m/s
V0
6.4 m/s
=
= 0.65 s
g
9.81 m/s 2
z = V0 t − 12 gt 2 = (6.4 m/s)(0.65 s) - 12 (9.81 m/s 2 )(0.65 s) 2 = 2.1 m
Therefore, Jones has 2×0.65 = 1.3 s to jump off from the platform to the roof since it takes another 0.65 s for the platform
to descend to the 10 m level.
Discussion
Like most stunts in the Indiana Jones movies, this would not be practical in reality.
6-47
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-67E
Solution
A box-enclosed fan is faced down so the air blast is directed downwards, and it is to be hovered by
increasing the blade rpm. The required blade rpm, air outlet velocity, the volumetric flow rate, and the minimum
mechanical power are to be determined.
Assumptions 1 The flow of air is steady and incompressible. 2 The air leaves the blades at a uniform velocity at
atmospheric pressure, and thus the momentum-flux correction factor can be taken to be unity, β ≅ 1. 3 Air approaches the
blades from the top through a large area at atmospheric pressure with negligible velocity. 4 The frictional effects are
negligible, and thus the entire mechanical power input is converted to kinetic energy of air (no conversion to thermal
energy through frictional effects). 5 The change in air pressure with elevation is negligible because of the low density of
air. 6 There is no acceleration of the fan, and thus the lift generated is equal to the total weight.
Properties
The density of air is given to be 0.078 lbm/ft3.
Analysis
(a) We take the control volume to be a vertical hyperbolic cylinder bounded by streamlines on the sides
with air entering through the large cross-section (section 1) at the top and the fan located at the narrow cross-section at the
bottom (section 2), and let its centerline be the z axis with upwards being the positive direction.
G
G
G
F=
βm V −
β m V . Noting that the only
The momentum equation for steady one-dimensional flow is
∑
∑
out
∑
in
force acting on the control volume is the total weight W and it acts in the negative z direction, the momentum equation
along the z axis gives
W
− W = m (−V 2 ) − 0
→
→
W = m V 2 = ( ρAV 2 )V 2 = ρAV 22
V2 =
ρA
where A is the blade span area,
A = πD 2 / 4 = π (3 ft) 2 / 4 = 7.069 ft 2
1
FRy
Then the discharge velocity to produce 5 lbf of upward force becomes
V2 =
⎛ 32.2 lbm ⋅ ft/s 2
⎜
1 lbf
(0.078 lbm/ft )(7.069 ft ) ⎜⎝
5 lbf
3
2
⎞
⎟ = 17.1 ft/s
⎟
⎠
(b) The volume flow rate and the mass flow rate of air are determined from their
definitions,
600 rpm
V = AV 2 = (7.069 ft 2 )(17.1 ft/s) = 121 ft 3 /s
2
m = ρV = (0.078 lbm/ft 3 )(121 ft 3/s) = 9.43 lbm/s
(c) Noting that P1 = P2 = Patm, V1 ≅ 0, the elevation effects are negligible, and the frictional effects are disregarded, the
energy equation for the selected control volume reduces to
⎛P V2
⎞
⎞
⎛P V2
m ⎜ 1 + 1 + gz1 ⎟ + W pump, u = m ⎜ 2 + 2 + gz 2 ⎟ + W turbine + E mech,loss →
⎟
⎜
⎟
⎜ρ
2
2
⎠
⎝ ρ
⎠
⎝
2
V
W fan, u = m 2
2
Substituting,
2
V
(18.0 ft/s) 2 ⎛
1 lbf
W fan,u = m 2 = (9.43 lbm/s)
⎜
2
2
⎝ 32.2 lbm ⋅ ft/s 2
1W
⎞⎛
⎞
⎟⎜
⎟ = 64.3 W
⎠⎝ 0.73756 lbf ⋅ ft/s ⎠
Therefore, the minimum mechanical power that must be supplied to the air stream is 64.3 W.
Discussion
The actual power input to the fan will be considerably larger than the calculated power input because of the
fan inefficiency in converting mechanical work to kinetic energy.
6-48
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-68
Solution
A parachute slows a soldier from his terminal velocity VT to his landing velocity of VF. A relation is to be
developed for the soldier’s velocity after he opens the parachute at time t = 0.
Assumptions 1 The air resistance is proportional to the velocity squared (i.e. F = -kV2). 2 The variation of the air
properties with altitude is negligible. 3 The buoyancy force applied by air to the person (and the parachute) is negligible
because of the small volume occupied and the low density of air. 4 The final velocity of the soldier is equal to its terminal
velocity with his parachute open.
Analysis
The terminal velocity of a free falling object is reached when the air resistance (or air drag) equals the
weight of the object, less the buoyancy force applied by the fluid, which is negligible in this case,
mg
Fair resistance = W →
kV F2 = mg →
k= 2
VF
This is the desired relation for the constant of proportionality k. When the parachute is deployed and the soldier starts to
decelerate, the net downward force acting on him is his weight less the air resistance,
⎛ V2 ⎞
mg
Fnet = W − Fair resistance = mg − kV 2 = mg − 2 V 2 = mg ⎜⎜1 − 2 ⎟⎟
Fair resistance
VF
⎝ VF ⎠
dV
gives
Substituting it into Newton’s 2nd law relation Fnet = ma = m
dt
⎛ V2 ⎞
dV
mg ⎜⎜1 − 2 ⎟⎟ = m
dt
⎝ VF ⎠
Canceling m and separating variables, and integrating from t = 0 when V = VT to
t = t when V = V gives
dV
Using
1−V
2
∫a
dx
/ V F2
− x2
integration limits,
2
1
2V F
= gdt
=
→
a+x
1
ln
2a a − x
∫
V
dV
VT V 2
F
−V
2
=
g
V F2
∫
t
0
dt
Parachute
W = mg
from integral tables and applying the
⎛ VF + V
V + VT ⎞ gt
⎜⎜ ln
⎟=
− ln F
−
V
V
V F − VT ⎟⎠ V F2
F
⎝
Rearranging, the velocity can be expressed explicitly as a function of time as
V = VF
Discussion
VT + V F + (VT − V F )e −2 gt / VF
VT + V F − (VT − V F )e − 2 gt / VF
Note that as t → ∞, the velocity approaches the landing velocity of VF, as expected.
6-49
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-69
Solution
An empty cart is to be driven by a horizontal water jet that enters from a hole at the rear of the cart. A
relation is to be developed for cart velocity versus time.
Assumptions 1 The flow of water is steady, one-dimensional, incompressible, and horizontal. 2 All the water which
enters the cart is retained. 3 The path of the cart is level and frictionless. 4 The cart is initially empty and stationary, and
thus V = 0 at time t = 0. 5 Friction between water jet and air is negligible, and the entire momentum of water jet is used to
drive the cart with no losses. 6 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be
unity, β ≅ 1.
Analysis
We note that the water jet velocity VJ is constant, but the car velocity V is variable. Noting that
m = ρA(V J − V ) where A is the cross-sectional area of the water jet and VJ - V is the velocity of the water jet relative to the
Cart
cart, the mass of water in the cart at any time t is
m0
t
t
t
m w = m dt = ρA(V J − V )dt = ρAV J t − ρA Vdt (1)
∫
0
∫
∫
0
0
Also,
V
Waterjet
dm w
= m = ρA(V J − V )
dt
We take the cart as the moving control volume. The net force acting on the cart in this case is equal to the momentum flux
of the water jet. Newton’s 2nd law F = ma = d(mV)/dt in this case can be expressed as
F=
d (m totalV )
dt
where
F=
∑ βm V − ∑ βm V = (m V )
in
= m VJ = ρA(VJ − V )VJ
in
out
and
d (m total V ) d [(m c + m w )V ]
dm w
dV d (m wV )
dV
dV
=
= mc
+
= mc
+ mw
+V
dt
dt
dt
dt
dt
dt
dt
dV
= (m c + m w )
+ ρA(V J − V )V
dt
Note that in β m V expressions, we used the fluid stream velocity relative to a fixed point. Substituting,
ρA(VJ − V )VJ = (mc + mw )
dV
+ ρA(VJ − V )V
dt
ρA(VJ − V )(VJ − V ) = (mc + mw )
→
dV
dt
Noting that mw is a function of t (as given by Eq. 1) and separating variables,
dV
dt
=
2
mc + mw
ρA(VJ − V )
→
dV
dt
=
t
2
ρA(VJ − V )
mc + ρAVJ t − ρA Vdt
∫
0
Integrating from t = 0 when V = 0 to t = t when V = V gives the desired integral,
∫
V
0
Discussion
dV
=
ρA(VJ − V ) 2
∫
t
dt
o
mc + ρAVJ t − ρA Vdt
∫
t
0
Note that the time integral involves the integral of velocity, which complicates the solution.
6-50
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-70
Solution
A plate is maintained in a horizontal position by frictionless vertical guide rails. The underside of the plate
is subjected to a water jet. The minimum mass flow rate m min to just levitate the plate is to be determined, and a relation is
to be obtained for the steady state upward velocity. Also, the integral that relates velocity to time when the water is first
turned on is to be obtained.
Assumptions 1 The flow of water is steady and one-dimensional. 2 The water jet splatters in the plane of he plate. 3 The
vertical guide rails are frictionless. 4 Times are short, so the velocity of the rising jet can be considered to remain constant
with height. 5 At time t = 0, the plate is at rest. 6 Jet flow is nearly uniform and thus the momentum-flux correction factor
can be taken to be unity, β ≅ 1.
Analysis
G
F=
∑
∑
(a) We take the plate as the system. The momentum equation for steady one-dimensional flow is
G
G
βm V −
β m V . Noting that m = ρAV J where A is the cross-sectional area of the water jet and W = mpg, the
∑
out
in
minimum mass flow rate of water needed to raise the plate is determined by setting the net force acting on the plate equal to
zero,
− W = 0 − m min V J
→
W = m min V J →
m min = ρAm p g
m p g = m min (m min / AV J ) →
For m > m min , a relation for the steady state upward velocity V is obtained setting the upward impulse applied by water jet
to the weight of the plate (during steady motion, the plate velocity V is constant, and the velocity of water jet relative to
plate is VJ –V),
W = m (V J − V )
m p g = ρA(V J − V ) 2
→
→ VJ −V =
(b) At time t = 0 the plate is at rest (V = 0), and it is subjected to water
jet with m > m min and thus the net force acting on it is greater than the
weight of the plate, and the difference between the jet impulse and the
weight will accelerate the plate upwards. Therefore, Newton’s 2nd law
F = ma = mdV/dt in this case can be expressed as
m (V J − V ) − W = m p a
→
ρA(V J − V ) 2 − m p g = m p
mpg
ρA
V
m p dV
0
ρ A(VJ − V ) − m p g
2
=∫
t
t =0
dt
→
t=∫
Guide
rails
W = mp g
dV
dt
V
m p dV
0
ρ A(VJ − V )2 − m p g
Discussion
This integral can be performed with the help of integral tables. But the
relation obtained will be implicit in V.
6-51
mpg
m
−
ρA
ρA
FRz
Separating the variables and integrating from t = 0 when V = 0 to t = t
when V = V gives the desired integral,
∫
→ V=
mp
.
m
Nozzle
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-71
Solution
Water enters a centrifugal pump axially at a specified rate and velocity, and leaves at an angle from the
axial direction. The force acting on the shaft in the axial direction is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The forces acting on the piping system in the horizontal
direction are negligible. 3 The atmospheric pressure is disregarded since it acts on all surfaces. 4 Water flow is nearly
uniform at the outlet and thus the momentum-flux correction factor can be taken to be unity, β ≅ 1.
Properties
We take the density of water to be 1000 kg/m3.
Analysis
From conservation of mass we have m 1 = m 2 = m , and thus
V1 = V2 and Ac1V1 = Ac 2V 2 . Noting that the discharge area is half the inlet
area, the discharge velocity is twice the inlet velocity. That is,
A
Ac1V 2 = c1 V1 = 2V1 = 2(5 m/s ) = 10 m/s
Ac 2
We take the pump as the control volume, and the inlet direction of flow as
the positive direction of x axis. The linear momentum equation in this case
in the x direction reduces to
G
G
G
βm V −
β m V
→ − FRx = m V 2 cosθ − m V1 →
F=
∑
∑
out
∑
z
x
60 °
m V
FRx
n
FRx = m (V1 − V 2 cosθ )
in
where the mass flow rate it
m = ρV = (1000 kg/m 3 )(0.20 m 3 /s) = 200 kg/s
Substituting the known quantities, the reaction force is determined to be (note that cos60° = 0.5)
⎛
1N
FRx = (200 kg/s)[(5 m/s) - (10 m/s)cos60]⎜⎜
2
⎝ 1 kg ⋅ m/s
⎞
⎟=0
⎟
⎠
Discussion
Note that at this angle of discharge, the bearing is not subjected to any horizontal loading. Therefore, the
loading in the system can be controlled by adjusting the discharge angle.
6-72
Solution
Water enters the impeller of a turbine through its outer edge of diameter D with velocity V making an angle
α with the radial direction at a mass flow rate of m , and leaves the impeller in the radial direction. The maximum power
sinα .
that can be generated is to be shown to be Wshaft = π nmDV
Assumptions
negligible.
α
1 The flow is steady in the mean. 2 Irreversible losses are
Analysis
We take the impeller region as the control volume. The
tangential velocity components at the inlet and the outlet are V1,t = 0 and
G
V
r2 =D/2
G
V
V 2,t = V sin α .
Normal velocity components as well pressure acting on the inner and
outer circumferential areas pass through the shaft center, and thus they do not
contribute to torque. Only the tangential velocity components contribute to
torque, and the application of the angular momentum equation gives
Tshaft = m (r2V 2,t − r1V1,t ) = m r2V 2,t − 0 = m D(V sin α ) / 2
ω
Tshaft
Impeller region
The angular velocity of the propeller is ω = 2πn . Then the shaft power
becomes
W shaft = ωTshaft = 2πn m D (V sin α ) / 2
Simplifying, the maximum power generated becomes W shaft = πn m DV sin α which is the desired relation.
Discussion
The actual power is less than this due to irreversible losses that are not taken into account in our analysis.
6-52
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-73
Solution
A two-armed sprinkler is used to water a garden. For specified flow rate and discharge angles, the rates of
rotation of the sprinkler head are to be determined.
θ
r = 0.45 m
•
θ
Assumptions 1 The flow is uniform and cyclically steady (i.e., steady from a frame of reference rotating with the
sprinkler head). 2 The water is discharged to the atmosphere, and thus the gage pressure at the nozzle outlet is zero. 3
Frictional effects and air drag of rotating components are neglected. 4 The nozzle diameter is small compared to the
moment arm, and thus we use average values of radius and velocity at the outlet.
We take the density of water to be 1000 kg/m3 = 1 kg/L.
Properties
Analysis
We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control
volume. The conservation of mass equation for this steady flow system is m 1 = m 2 = m . Noting that the two nozzles are
identical, we have m nozzle = m / 2 or Vnozzle = Vtotal / 2 since the density of water is constant. The average jet outlet velocity
relative to the nozzle is
V jet =
⎛ 1m3 ⎞
Vnozzle
60 L/s
⎜
⎟ = 95.49 m/s
=
2
A jet
2[π (0.02 m) / 4] ⎜⎝ 1000 L ⎟⎠
The angular momentum equation can be expressed as
∑ M = ∑ rm V − ∑ rm V . Noting that there are no external
out
in
moments acting, the angular momentum equation about the axis of rotation becomes
0 = −2rm nozzleV r cos θ
→
Vr = 0
→
V jet,t −V nozzle = 0
Noting that the tangential component of jet velocity is V jet, t = V jet cos θ , we have
V nozzle = V jet cos θ = (95.49 m/s)cosθ
Also noting that V nozzle = ωr = 2πn r , and angular speed and the rate of rotation of sprinkler head become
1) θ = 0°: ω =
Vnozzle ( 95.49 m/s ) cos0
=
= 212 rad/s
0.45 m
r
and
n =
ω 212 rad/s ⎛ 60 s ⎞
=
⎜
⎟ = 2026 rpm ≅ 2030 rpm
2π
2π
⎝ 1 min ⎠
2) θ = 30°: ω =
Vnozzle ( 95.49 m/s ) cos30°
ω 184 rad/s ⎛ 60 s ⎞
=
= 184 rad/s and n =
=
⎜
⎟ = 1755 rpm ≅ 1760 rpm
0.45 m
2π
2π
r
⎝ 1 min ⎠
3) θ = 60°: ω =
Vnozzle ( 95.49 m/s ) cos60°
ω 106 rad/s ⎛ 60 s ⎞
=
= 106 rad/s and n =
=
⎜
⎟ = 1013 rpm ≅ 1010 rpm
0.45 m
2π
2π
r
⎝ 1 min ⎠
Discussion
Final results are given to three significant digits, as usual. The rate of rotation in reality will be lower
because of frictional effects and air drag.
6-53
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-74
Solution
The previous problem is reconsidered. The effect of discharge angle θ on the rate of rotation n as θ varies
from 0 to 90° in increments of 10° is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
D=0.02 "m"
r=0.45 "m"
n_nozzle=2 "number of nozzles"
Ac=pi*D^2/4
V_jet=V_dot/Ac/n_nozzle
V_nozzle=V_jet*cos(theta)
V_dot=0.060 "m3/s"
omega=V_nozzle/r
n_dot=omega*60/(2*pi)
Angle,
θ°
0
10
20
30
40
50
60
70
80
90
n
rpm
2026
1996
1904
1755
1552
1303
1013
693
352
0
ω
rad/s
212
209
199
184
163
136
106
73
37
0
Vnozzle ,
m/s
95.5
94.0
89.7
82.7
73.2
61.4
47.7
32.7
16.6
0.0
2250
n, rpm
1800
1350
900
450
0
0
10
20
30
40
θ, °
50
60
70
80
90
Discussion
The maximum rpm occurs when θ = 0o, as expected, since this represents purely tangential outflow. When θ
o
= 90 , the rpm drops to zero, as also expected, since the outflow is purely radial and therefore there is no torque to spin the
sprinkler.
6-54
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems
6-75
Solution
A stationary water tank placed on wheels on a frictionless surface is propelled by a water jet that leaves the
tank through a smooth hole. Relations are to be developed for the acceleration, the velocity, and the distance traveled by
the tank as a function of time as water discharges.
Assumptions 1 The orifice has a smooth entrance, and thus the frictional losses are negligible. 2 The flow is steady,
incompressible, and irrotational (so that the Bernoulli equation is applicable). 3 The surface under the wheeled tank is level
and frictionless. 4 The water jet is discharged horizontally and rearward. 5 The mass of the tank and wheel assembly is
negligible compared to the mass of water in the tank. 4 Jet flow is nearly uniform and thus the momentum-flux correction
factor can be taken to be unity, β ≅ 1.
Analysis
(a) We take point 1 at the free surface of the tank, and point 2 at
the outlet of the hole, which is also taken to be the reference level (z2 = 0) so that
the water height above the hole at any time is z. Noting that the fluid velocity at
the free surface is very low (V1 ≅ 0), it is open to the atmosphere (P1 = Patm), and
water discharges into the atmosphere (and thus P2 = Patm), the Bernoulli equation
simplifies to
V22
V12
P
P1
+
+ z1 = 2 +
+ z2
ρg 2 g
ρg 2 g
→
z=
VJ2
2g
+0
→
1
z
x
D
VJ = 2 gz
D0
VJ
2
The discharge rate of water from the tank through the hole is
m = ρAV J = ρ
πD02
4
VJ = ρ
πD02
4
2 gz
The momentum equation for steady one-dimensional flow is
G
G
G
∑ F = ∑ βm V − ∑ βm V . Applying it to the water tank,
out
in
the horizontal force that acts on the tank is determined to be
F = m V e − 0 = m V J = ρ
πD02
2 gz = ρgz
πD02
4
2
The acceleration of the water tank is determined from Newton’s 2nd law of motion F = ma where m is the mass of water in
the tank, m = ρV tank = ρ (πD 2 / 4 ) z ,
a=
2
F ρ gz (π D0 / 2 )
=
m ρ z (π D 2 / 4 )
a = 2g
→
D02
D2
Note that the acceleration of the tank is constant.
(b) Noting that a = dV/dt and thus dV = adt and acceleration a is constant, the velocity is expressed as
D02
t
D2
(c) Noting that V = dx/dt and thus dx = Vdt, the distance traveled by the water tank is determined by integration to be
V = at
→
dx = Vdt
→
V = 2g
dx = 2 g
D02
tdt
D2
→
x=g
D02 2
t
D2
since x = 0 at t = 0.
Discussion
In reality, the flow rate discharge velocity and thus the force acting on the water tank will be less because of
the frictional losses at the hole. But these losses can be accounted for by incorporating a discharge coefficient.
Design and Essay Problems
6-76
Solution
Students’ essays and designs should be unique and will differ from each other.
KJ
6-55
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications
by Çengel & Cimbala
CHAPTER 7
DIMENSIONAL ANALYSIS AND MODELING
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of The McGraw-Hill Companies, Inc.
(“McGraw-Hill”) and protected by copyright and other state and federal laws. By
opening and using this Manual the user agrees to the following restrictions, and if the
recipient does not agree to these restrictions, the Manual should be promptly returned
unopened to McGraw-Hill: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated
textbook. No other use or distribution of this Manual is permitted. This Manual
may not be sold and may not be distributed to or used by any student or other
third party. No part of this Manual may be reproduced, displayed or distributed
in any form or by any means, electronic or otherwise, without the prior written
permission of McGraw-Hill.
7-1
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Dimensions and Units, Primary Dimensions
7-1C
Solution
We are to explain the difference between a dimension and a unit, and give examples.
Analysis
A dimension is a measure of a physical quantity (without numerical values), while a unit is a way to
assign a number to that dimension. Examples are numerous – length and meter, temperature and oC, weight and lbf, mass
and kg, time and second, power and watt,…
Discussion
units.
7-2C
Solution
When performing dimensional analysis, it is important to recognize the difference between dimensions and
We are to append the given table with other parameters and their primary dimensions.
Analysis
Students’ tables will differ, but they should add entries such as angular velocity, kinematic viscosity, work,
energy, power, specific heat, thermal conductivity, torque or moment, stress, etc.
Discussion
This problem should be assigned as an ongoing homework problem throughout the semester, and then
collected towards the end. Individual instructors can determine how many entries to be required in the table.
7-3C
Solution
We are to list the seven primary dimensions and explain their significance.
Analysis
The seven primary dimensions are mass, length, time, temperature, electrical current, amount of light,
and amount of matter. Their significance is that all other dimensions can be formed by combinations of these seven
primary dimensions.
Discussion
One of the first steps in a dimensional analysis is to write down the primary dimensions of every variable or
parameter that is important in the problem.
7-4
Solution
We are to write the primary dimensions of the universal ideal gas constant.
Analysis
From the given equation,
Primary dimensions of the universal ideal gas constant:
⎧ m
⎫
× L3 ⎪
⎧ pressure × volume ⎫ ⎪⎪ t 2 L
⎪
{Ru } = ⎨
⎬=⎨
⎬=
⎩ mol × temperature ⎭ ⎪ N × T ⎪
⎩⎪
⎭⎪
⎧ mL2 ⎫
⎨ 2
⎬
⎩ t TN ⎭
Or, in exponent form, {Ru} = {m1 L2 t-2 T-1 N-1}.
Discussion
the result.
The standard value of Ru is 8314.3 J/kmol⋅K. You can verify that these units agree with the dimensions of
7-2
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-5
Solution
We are to write the primary dimensions of atomic weight.
Analysis
By definition, atomic weight is mass per mol,
{M } = ⎧⎨
mass ⎫ ⎧ m ⎫
⎬= ⎨ ⎬
⎩ mol ⎭ ⎩ N ⎭
Primary dimensions of atomic weight:
(1)
Or, in exponent form, {M} = {m1 N-1}.
Discussion
In terms of primary dimensions, atomic mass is not dimensionless, although many authors treat it as such.
Note that mass and amount of matter are defined as two separate primary dimensions.
7-6
Solution
We are to write the primary dimensions of the universal ideal gas constant in the alternate system where
force replaces mass as a primary dimension.
Analysis
From Newton’s second law, force equals mass times acceleration. Thus, mass is written in terms of force as
Primary dimensions of mass in the alternate system:
2
force
⎫ ⎧ F ⎫ ⎧ Ft ⎫
{mass} = ⎧⎨
⎬=⎨ 2⎬=⎨
⎬
⎩ acceleration ⎭ ⎩ L/t ⎭ ⎩ L ⎭
(1)
We substitute Eq. 1 into the results of Problem 7-4,
Primary dimensions of the universal ideal gas constant:
⎧ Ft 2 2 ⎫
L ⎪
⎧ mL ⎫ ⎪
FL
{Ru } = ⎨ 2 ⎬ = ⎨⎪ L 2 ⎬⎪ = ⎧⎨ ⎫⎬
⎩ Nt T ⎭ ⎪ Nt T ⎪ ⎩ TN ⎭
⎪⎩
⎪⎭
2
(2)
Or, in exponent form, {Ru} = {F1 L1 T-1 N-1}.
Discussion
Eq. 2.
The standard value of Ru is 8314.3 J/kmol⋅K. You can verify that these units agree with the dimensions of
7-3
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-7
Solution
We are to write the primary dimensions of the specific ideal gas constant, and verify are result by
comparing to the standard SI units of Rair.
Analysis
We can approach this problem two ways. If we have already worked through Problem 7-4, we can use our
results. Namely,
Primary dimensions of specific ideal gas constant:
{R }
gas
⎧ mL2 ⎫
⎧ R ⎫ ⎪⎪ 2 ⎪⎪ ⎧ L2 ⎫
= ⎨ u ⎬ = ⎨ Nt T ⎬ = ⎨ 2 ⎬
⎩ M ⎭ ⎪ m ⎪ ⎩t T⎭
⎩⎪ N ⎭⎪
(1)
Or, in exponent form, {Rgas} = {L2 t-2 T-1}. Alternatively, we can use either form of the ideal gas law,
Primary dimensions of specific ideal gas constant:
{R }
gas
⎧ m
⎫
× L3 ⎪ ⎧ 2 ⎫
⎧ pressure × volume ⎫ ⎪⎪ t 2 L
L
⎪
=⎨
⎬=⎨
⎬= ⎨ 2 ⎬
t
×
×
mass
temperature
m
T
⎩
⎭ ⎪
⎪ ⎩ T⎭
⎪⎩
⎭⎪
(2)
For air, Rair = 287.0 J/kg⋅K. We transform these units into primary dimensions,
Primary dimensions of the specific ideal gas constant for air:
⎧ mL2 ⎫
⎧
J ⎫ ⎪⎪ t 2 ⎪⎪
{Rair } = ⎨287.0
⎬=⎨
⎬=
kg×K ⎭ ⎪ m × T ⎪
⎩
⎩⎪
⎭⎪
⎧ L2 ⎫
⎨ 2 ⎬
⎩t T⎭
(3)
Equation 3 agrees with Eq. 1 and Eq. 2, increasing our confidence that we have performed the algebra correctly.
Discussion
Notice that numbers, like the value 287.0 in Eq. 3 have no influence on the dimensions.
7-8
Solution
We are to write the primary dimensions of torque and list its units.
Analysis
Torque is the product of a length and a force,
Primary dimensions of torque:
G
⎫ ⎧ L ⎫
⎬ = ⎨m ⎬
{M } = ⎧⎨⎩length × mass length
time ⎭ ⎩ t ⎭
2
2
2
(1)
G
Or, in exponent form, { M } = {m1 L2 t-2}. The common units of torque are newton-meter (SI) and inch-pound
(English). In primary units, however, we write the primary SI units according to Eq. 1,
Primary SI units:
Units of torque = kg ⋅ m 2 /s 2
and in primary English units,
Primary English units:
Units of torque = lbm ⋅ ft 2 /s 2
Discussion
Since torque is the product of a force and a length, it has the same dimensions as energy. Primary units are
not required for dimensional analysis, but are often useful for unit conversions and for verification of proper units when
solving a problem.
7-4
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-9
Solution
We are to determine the primary dimensions of each variable.
Analysis
(a) Energy is force times length (the same dimensions as work),
Primary dimensions of energy:
2
mass × length
⎫ ⎧ mL ⎫
length
×
=
⎬
⎨
2 ⎬
time2
⎩
⎭ ⎩ t ⎭
{E} = {force × length} = ⎧⎨
(1)
Or, in exponent form, {E} = {m1 L2 t-2}.
(b) Specific energy is energy per unit mass,
Primary dimensions of specific energy:
energy ⎫ ⎧ mass × length 2
1 ⎫ ⎧ L2 ⎫
×
{e} = ⎧⎨
⎬=⎨
⎬=⎨ ⎬
mass ⎭ ⎩ t 2 ⎭
time 2
⎩ mass ⎭ ⎩
(2)
Or, in exponent form, {e} = { L2 t-2}.
(c) Power is the rate of change of energy, i.e. energy per unit time,
Primary dimensions of power:
2
1 ⎫ ⎧ mL2 ⎫
⎧ energy ⎫ ⎧ mass × length
W = ⎨
×
⎬=⎨
⎬=⎨
⎬
2
time ⎭ ⎩ t 3 ⎭
time
⎩ time ⎭ ⎩
{ }
(3)
Or, in exponent form, { W } = {m1 L2 t-3}.
Discussion
In dimensional analysis it is important to distinguish between energy, specific energy, and power.
7-10
Solution
We are to determine the primary dimensions of electrical voltage.
Analysis
From the hint,
Primary dimensions of voltage:
⎧ mass × length 2
power ⎫ ⎪⎪
time3
{voltage} = ⎨⎧
⎬=⎨
current
⎩ current ⎭ ⎪
⎪⎩
⎫
2
⎪⎪ ⎧ mL ⎫
=
⎬ ⎨ 3 ⎬
⎪ ⎩ t I ⎭
⎪⎭
(1)
Or, in exponent form, {E} = {m1 L2 t-3 I-1}.
Discussion
dimensions.
We see that all dimensions, even those of electrical properties, can be expressed in terms of primary
7-5
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-11
Solution
Analysis
current,
We are to write the primary dimensions of electrical resistance.
From Ohm’s law, we see that resistance has the dimensions of voltage difference divided by electrical
Primary dimensions of resistance:
⎧ mass × length 2 ⎫
⎪
⎪ ⎧ mL2 ⎫
3
ΔE
{R} = ⎨⎧ ⎬⎫ = ⎨⎪ time × current ⎪⎬ = ⎨ 3 2 ⎬
current
⎩ I ⎭ ⎪
⎪ ⎩t I ⎭
⎩⎪
⎭⎪
Or, in exponent form, {R} = {m1 L2 t-3 I-2}, where we have also used the result of the previous problem.
Discussion
All dimensions can be written in terms of primary dimensions.
7-12
Solution
We are to determine the primary dimensions of each variable.
Analysis
(a) Acceleration is the rate of change of velocity,
Primary dimensions of acceleration:
{a} = ⎨⎧
velocity ⎫ ⎧ length
1 ⎫ ⎧L ⎫
×
⎬=⎨
⎬=⎨ 2⎬
⎩ time ⎭ ⎩ time time ⎭ ⎩ t ⎭
(1)
Or, in exponent form, {a} = { L1 t-2}.
(b) Angular velocity is the rate of change of angle,
Primary dimensions of angular velocity:
{ω} = ⎧⎨
angle ⎫ ⎧ 1 ⎫ ⎧ 1 ⎫
⎬=⎨
⎬=⎨ ⎬
⎩ time ⎭ ⎩ time ⎭ ⎩ t ⎭
(2)
Or, in exponent form, {ω} = { t-1}.
(c) Angular acceleration is the rate of change of angular velocity,
Primary dimensions of angular acceleration:
angular velocity ⎫ ⎧ 1
1 ⎫ ⎧1⎫
×
{α = ω } = ⎨⎧
⎬=⎨
⎬=⎨ 2⎬
time
⎩
⎭ ⎩ time time ⎭ ⎩ t ⎭
(3)
Or, in exponent form, {α} = { t-2}.
Discussion
In Part (b) we note that the unit of angle is radian, which is a dimensionless unit. Therefore the dimensions
of angle are unity.
7-6
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-13
Solution
We are to write the primary dimensions of angular momentum and list its units.
Analysis
Angular momentum is the product of length, mass, and velocity,
Primary dimensions of angular momentum:
G
length ⎫ ⎧ mL2 ⎫
⎧
(1)
H = ⎨length × mass ×
⎬=⎨
⎬
t
time
⎩
⎭ ⎩
⎭
G
Or, in exponent form, { H } = {m1 L2 t-1}. We write the primary SI units according to Eq. 1,
{ }
Units of angular momentum =
Primary SI units:
kg ⋅ m 2
s
and in primary English units,
Units of angular momentum =
Primary English units:
lbm ⋅ ft 2
s
Discussion
Primary units are not required for dimensional analysis, but are often useful for unit conversions and for
verification of proper units when solving a problem.
7-14
Solution
We are to determine the primary dimensions of each variable.
Analysis
(a) Specific heat is energy per unit mass per unit temperature,
Primary dimensions of specific heat at constant pressure:
{c }
p
⎧ mL2 ⎫
⎧
⎫ ⎪⎪ t 2 ⎪⎪ ⎧ L2 ⎫
energy
=⎨
⎬=⎨
⎬=⎨ 2 ⎬
⎩ mass × temperature ⎭ ⎪ m × T ⎪ ⎩ t T ⎭
⎩⎪
⎭⎪
(1)
Or, in exponent form, {cp} = { L2 t-2 T-1}.
(b) Specific weight is density times gravitational acceleration,
⎧ mass length ⎫ ⎧ m ⎫
=⎨ 2 2⎬
Primary dimensions of specific weight: { ρ g} = ⎨
2 ⎬
⎩ volume time ⎭ ⎩ L t ⎭
(2)
Or, in exponent form, {ρg} = {m1 L-2 t-2}.
(c) Specific enthalpy has dimensions of energy per unit mass,
⎧ mL2
⎧ energy ⎫ ⎪⎪ t 2
Primary dimensions of specific enthalpy: {h} = ⎨
⎬=⎨
⎩ mass ⎭ ⎪ m
⎪⎩
⎫
2
⎪⎪ ⎧ L ⎫
⎬=⎨ 2 ⎬
⎪ ⎩t ⎭
⎪⎭
(3)
Or, in exponent form, {h} = { L2 t-2}.
Discussion
As a check, from our study of thermodynamics we know that dh = cpdT for an ideal gas. Thus, the
dimensions of dh must equal the dimensions of cp times the dimensions of dT. Comparing Eqs. 1 and 3 above, we see that
this is indeed the case.
7-7
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-15
Solution
We are to determine the primary dimensions of thermal conductivity.
Analysis
The primary dimensions of Q conduction are energy/time, and the primary dimensions of dT/dx are
temperature/length. From the given equation,
Primary dimensions of thermal conductivity:
⎧
⎫ ⎧ mL2 ⎫
energy
⎪⎪
⎪⎪ ⎪⎪ t 3 ⎪⎪ ⎧ mL ⎫
time
{k } = ⎨
⎬=⎨
⎬=⎨ 3 ⎬
⎪ length 2 × temperature ⎪ ⎪ L × T ⎪ ⎩ t T ⎭
length ⎪⎭ ⎪⎩
⎪⎩
⎪⎭
(1)
Or, in exponent form, {k} = {m1 L1 t-3 T-1}. We obtain a value of k from a reference book. E.g. kcopper = 401 W/m⋅K. These
units have dimensions of power/length⋅temperature. Since power is energy/time, we see immediately that Eq. 1 is correct.
Alternatively, we can transform the units of k into primary units,
Primary SI units of thermal conductivity:
kcopper = 401
kg ⋅ m
W ⎛ N m ⎞⎛ kg m ⎞
= 401 3
2 ⎟
m K ⎜⎝ s W ⎟⎜
N
s
s ⋅K
⎠⎝
⎠
(2)
Discussion
We have used the principle of dimensional homogeneity to determine the primary dimensions of k. Namely,
we utilized the fact that the dimensions of both terms of the given equation must be identical.
7-16
Solution
We are to determine the primary dimensions of each variable.
Analysis
(a) Heat generation rate is energy per unit volume per unit time,
Primary dimensions of heat generation rate:
⎧ mL2
energy
⎫ ⎪⎪ t 2
{ g } = ⎧⎨
⎬=⎨ 3
⎩ volume × time ⎭ ⎪ L t
⎩⎪
⎫
⎪⎪ ⎧ m ⎫
⎬=⎨ 3⎬
⎪ ⎩ Lt ⎭
⎭⎪
(1)
Or, in exponent form, { g } = {m1 L-1 t-3}.
(b) Heat flux is energy per unit area per unit time,
Primary dimensions of heat flux:
⎧ mL2
energy ⎫ ⎪⎪ t 2
{q} = ⎧⎨
⎬=⎨ 2
⎩ area × time ⎭ ⎪ L t
⎩⎪
⎫
⎪⎪ ⎧ m ⎫
⎬=⎨ 3⎬
⎪ ⎩t ⎭
⎭⎪
(2)
Or, in exponent form, { q } = {m1 t-3}.
(c) Heat flux is energy per unit area per unit time per unit temperature,
Primary dimensions of heat transfer coefficient:
⎧ mL2 ⎫
⎪⎪ ⎧ m ⎫
⎧
⎫ ⎪⎪
energy
t2
{h} = ⎨
⎬=⎨ 2
⎬=⎨ 3 ⎬
⎩ area × time × temperature ⎭ ⎪ L × t × T ⎪ ⎩ t T ⎭
⎪⎩
⎪⎭
(3)
Or, in exponent form, {h} = {m1 t-3 T-1}.
Discussion
variables.
In the field of heat transfer it is critical that one be careful with the dimensions (and units) of heat transfer
7-8
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-17
Solution
dimensions.
We are to choose three properties or constants and write out their names, their SI units, and their primary
Analysis
There are many options. For example,
Students may choose cv (specific heat at constant volume). The units are kJ/kg⋅K, which is energy per mass per
temperature. Thus,
Primary dimensions of specific heat at constant volume:
⎧ mL2 ⎫
⎧
⎫ ⎪⎪ t 2 ⎪⎪ ⎧ L2 ⎫
energy
{cv } = ⎨
⎬=⎨
⎬=⎨ 2 ⎬
⎩ mass × temperature ⎭ ⎪ m × T ⎪ ⎩ t T ⎭
⎩⎪
⎭⎪
(1)
Or, in exponent form, {cv} = { L2 t-2 T-1}.
Students may choose v (specific volume). The units are m3/kg, which is volume per mass. Thus,
volume ⎫ ⎧ L3 ⎫
⎬=⎨ ⎬
⎩ mass ⎭ ⎩ m ⎭
{v } = ⎧⎨
Primary dimensions of specific volume:
(2)
Or, in exponent form, {v} = {m-1 L3}.
Students may choose hfg (latent heat of vaporization). The units are kJ/kg, which is energy per mass. Thus,
Primary dimensions of latent heat of vaporization:
{h }
fg
⎧ mL2
⎧ energy ⎫ ⎪⎪ t 2
=⎨
⎬=⎨
⎩ mass ⎭ ⎪ m
⎪⎩
⎫
2
⎪⎪ ⎧ L ⎫
=
⎬ ⎨ 2⎬
⎪ ⎩t ⎭
⎪⎭
(3)
Or, in exponent form, {hfg} = {L2 t-2}. (The same dimensions hold for hf and hg.)
Students may choose sf (specific entropy of a saturated liquid). The units are kJ/kg⋅K, which is energy per mass per
temperature. Thus,
Primary dimensions of specific entropy of a saturated liquid:
⎧ mL2 ⎫
⎧
⎫ ⎪⎪ t 2 ⎪⎪ ⎧ L2 ⎫
energy
sf = ⎨
⎬=⎨
⎬=⎨ 2 ⎬
⎩ mass × temperature ⎭ ⎪ m × T ⎪ ⎩ t T ⎭
⎪⎩
⎪⎭
{ }
(4)
Or, in exponent form, {sf} = { L2 t-2 T-1}. (The same dimensions hold for sfg and sg.)
Discussion
Students’ answers will vary. There are some other choices.
7-9
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-18E
Solution
dimensions.
We are to choose three properties or constants and write out their names, their SI units, and their primary
Analysis
There are many options. For example,
Students may choose cv (specific heat at constant volume). The units are Btu/lbm⋅R, which is energy per mass per
temperature. Thus,
Primary dimensions of specific heat at constant volume:
⎧ mL2 ⎫
⎧
⎫ ⎪⎪ t 2 ⎪⎪ ⎧ L2 ⎫
energy
{cv } = ⎨
⎬=⎨
⎬=⎨ 2 ⎬
⎩ mass × temperature ⎭ ⎪ m × T ⎪ ⎩ t T ⎭
⎩⎪
⎭⎪
(1)
Or, in exponent form, {cv} = { L2 t-2 T-1}.
Students may choose v (specific volume). The units are ft3/lbm, which is volume per mass. Thus,
volume ⎫ ⎧ L3 ⎫
⎬=⎨ ⎬
⎩ mass ⎭ ⎩ m ⎭
{v } = ⎧⎨
Primary dimensions of specific volume:
(2)
Or, in exponent form, {v} = {m-1 L3}.
Students may choose hfg (latent heat of vaporization). The units are Btu/lbm, which is energy per mass. Thus,
Primary dimensions of latent heat of vaporization:
{h }
fg
⎧ mL2
⎧ energy ⎫ ⎪⎪ t 2
=⎨
⎬=⎨
⎩ mass ⎭ ⎪ m
⎪⎩
⎫
2
⎪⎪ ⎧ L ⎫
=
⎬ ⎨ 2⎬
⎪ ⎩t ⎭
⎪⎭
(3)
Or, in exponent form, {hfg} = {L2 t-2}. (The same dimensions hold for hf and hg.)
Students may choose sf (specific entropy of a saturated liquid). The units are Btu/lbm⋅R, which is energy per mass per
temperature. Thus,
Primary dimensions of specific entropy of a saturated liquid:
⎧ mL2 ⎫
⎧
⎫ ⎪⎪ t 2 ⎪⎪ ⎧ L2 ⎫
energy
sf = ⎨
⎬=⎨
⎬=⎨ 2 ⎬
⎩ mass × temperature ⎭ ⎪ m × T ⎪ ⎩ t T ⎭
⎪⎩
⎪⎭
{ }
(4)
Or, in exponent form, {sf} = { L2 t-2 T-1}. (The same dimensions hold for sfg and sg.)
Discussion
Students’ answers will vary. There are some other choices.
7-10
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Dimensional Homogeneity
7-19C
Solution
We are to explain the law of dimensional homogeneity.
Analysis
The law of dimensional homogeneity states that every additive term in an equation must have the same
dimensions. As a simple counter example, an equation with one term of dimensions length and another term of dimensions
temperature would clearly violate the law of dimensional homogeneity – you cannot add length and temperature. All terms
in the equation must have the same dimensions.
Discussion
If in the solution of an equation you realize that the dimensions of two terms are not equivalent, this is a
sure sign that you have made a mistake somewhere!
7-20
Solution
We are to determine the primary dimensions of the gradient operator, and then verify that primary
dimensions of each additive term in the equation are the same.
Analysis
(a) By definition, the gradient operator is a three-dimensional derivative operator. For example, in Cartesian coordinates,
Gradient operator in Cartesian coordinates:
G ⎛ ∂ ∂ ∂ ⎞ G ∂ G ∂ G ∂
∇=⎜ , , ⎟=i
+j
+k
∂x
∂y
∂z
⎝ ∂x ∂y ∂z ⎠
Therefore its dimensions must be 1/length. Thus,
Primary dimensions of the gradient operator:
G
{∇} = ⎧⎨⎩ L1 ⎫⎬⎭
G
Or, in exponent form, { ∇ } = { L-1}.
(b) Similarly, the primary dimensions of a time derivative (∂/∂t) are 1/time. Also, the primary dimensions of velocity are
length/time, and the primary dimensions of acceleration are length/time2. Thus each term in the given equation can be
written in terms of primary dimensions,
G
G
{a} = ⎧⎨
{a} = ⎨⎧
length ⎫
2 ⎬
⎩ time ⎭
⎧ length ⎫
G
⎪⎧ ∂V ⎪⎫ ⎪⎪ time ⎪⎪ ⎧ length ⎫
⎨ ⎬=⎨
⎬=⎨
2 ⎬
⎩⎪ ∂t ⎭⎪ ⎪ time ⎪ ⎩ time ⎭
⎩⎪
⎭⎪
L⎫
2 ⎬
⎩t ⎭
G
⎪⎧ ∂V ⎪⎫ ⎧ L ⎫
⎨ ⎬=⎨ 2⎬
⎩⎪ ∂t ⎭⎪ ⎩ t ⎭
G G G
1
length ⎫ ⎧ length ⎫
×
×
⎬=⎨
⎬
{(V ⋅∇ )V } = ⎨⎩⎧ length
time length time ⎭ ⎩ time ⎭
2
G G G
{(V ⋅ ∇ )V } = ⎩⎧⎨ tL ⎭⎫⎬
2
Indeed, all three additive terms have the same dimensions, namely {L1 t-2}.
Discussion
If the dimensions of any of the terms were different from the others, it would be a sure sign that an error
was made somewhere in deriving or copying the equation.
7-11
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-21
Solution
We are to determine the primary dimensions of each additive term in the equation, and we are to verify that
the equation is dimensionally homogeneous.
Analysis
The primary dimensions of the time derivative (∂/∂t) are 1/time. The primary dimensions of the gradient
vector are 1/length, and the primary dimensions of velocity are length/time. Thus each term in the equation can be written
in terms of primary dimensions,
⎧ mass×length ⎫
G
⎪⎪
⎧⎪ F ⎫⎪ ⎧ force ⎫ ⎪⎪
time 2
⎨ ⎬=⎨
⎬=⎨
⎬
mass
⎪⎩ m ⎪⎭ ⎩ mass ⎭ ⎪
⎪
⎪⎩
⎪⎭
G
⎪⎧ F ⎪⎫ ⎧ L ⎫
⎨ ⎬=⎨ 2⎬
⎩⎪ m ⎭⎪ ⎩ t ⎭
⎧ length ⎫
G
⎧⎪ ∂V ⎫⎪ ⎪⎪ time ⎪⎪
⎨
⎬=⎨
⎬
⎩⎪ ∂t ⎭⎪ ⎪ time ⎪
⎪⎩
⎪⎭
G
⎧⎪ ∂V ⎫⎪ ⎧ L ⎫
⎨ ⎬=⎨ 2⎬
⎩⎪ ∂t ⎭⎪ ⎩ t ⎭
1
length ⎫
×
×
⎬
{(V ⋅∇ )V } = ⎧⎨⎩ length
time length time ⎭
{(V ⋅∇ )V } = ⎧⎨⎩ tL ⎫⎬⎭
G G G
G G G
2
Indeed, all three additive terms have the same dimensions, namely {L1 t-2}.
Discussion
The dimensions are, in fact, those of acceleration.
7-22
Solution
We are to determine the primary dimensions of each additive term in Eq. 1, and we are to verify that the
equation is dimensionally homogeneous.
Analysis
The primary dimensions of the material derivative (D/Dt) are 1/time. The primary dimensions of volume are
length3, and the primary dimensions of velocity are length/time. Thus each term in the equation can be written in terms of
primary dimensions,
length 3 ⎫ ⎧ 1 ⎫
⎧ 1 DV ⎫ ⎧ 1
=
×
⎨
⎬ ⎨
⎬=⎨
⎬
3
time ⎭ ⎩ time ⎭
⎩V Dt ⎭ ⎩ length
⎧ 1 DV ⎫ ⎧ 1 ⎫
⎨
⎬=⎨ ⎬
⎩V Dt ⎭ ⎩ t ⎭
⎧ length ⎫
⎧ ∂u ⎫ ⎪⎪ time ⎪⎪ ⎧ 1 ⎫
⎨ ⎬=⎨
⎬=⎨
⎬
⎩ ∂x ⎭ ⎪ length ⎪ ⎩ time ⎭
⎩⎪
⎭⎪
⎧ ∂u ⎫ ⎧ 1 ⎫
⎨ ⎬=⎨ ⎬
⎩ ∂x ⎭ ⎩ t ⎭
⎧ length ⎫
⎧ ∂v ⎫ ⎪⎪ time ⎪⎪ ⎧ 1 ⎫
⎨ ⎬=⎨
⎬=⎨
⎬
⎩ ∂y ⎭ ⎪ length ⎪ ⎩ time ⎭
⎩⎪
⎭⎪
⎧ ∂v ⎫ ⎧ 1 ⎫
⎨ ⎬=⎨ ⎬
⎩ ∂y ⎭ ⎩ t ⎭
⎧ length ⎫
⎧ ∂w ⎫ ⎪⎪ time ⎪⎪ ⎧ 1 ⎫
⎨ ⎬=⎨
⎬=⎨
⎬
⎩ ∂z ⎭ ⎪ length ⎪ ⎩ time ⎭
⎪⎩
⎪⎭
⎧ ∂w ⎫ ⎧ 1 ⎫
⎨ ⎬=⎨ ⎬
⎩ ∂z ⎭ ⎩ t ⎭
Indeed, all four additive terms have the same dimensions, namely {t-1}.
Discussion
If the dimensions of any of the terms were different from the others, it would be a sure sign that an error
was made somewhere in deriving or copying the equation.
7-12
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-23
Solution
We are to determine the primary dimensions of each additive term, and we are to verify that the equation is
dimensionally homogeneous.
Analysis
The primary dimensions of the velocity components are length/time. The primary dimensions of coordinates
r and z are length, and the primary dimensions of coordinate θ are unity (it is a dimensionless angle). Thus each term in the
equation can be written in terms of primary dimensions,
length ⎫
⎧
length
⎧⎪ 1 ∂ ( rur ) ⎫⎪ ⎪⎪ 1
time ⎪⎪ = ⎧ 1 ⎫
×
⎨
⎬=⎨
⎬ ⎨
⎬
length
⎪ ⎩ time ⎭
⎩⎪ r ∂r ⎭⎪ ⎪ length
⎩⎪
⎭⎪
⎧⎪ 1 ∂ ( rur ) ⎫⎪ ⎧ 1 ⎫
⎨
⎬=⎨ ⎬
⎩⎪ r ∂r ⎭⎪ ⎩ t ⎭
length ⎫
⎧
⎧ 1 ∂uθ ⎫
⎪⎪ 1
⎪⎪ ⎧ 1 ⎫
× time ⎬ = ⎨
⎨
⎬ == ⎨
⎬
1 ⎪ ⎩ time ⎭
⎩ r ∂θ ⎭
⎪ length
⎪⎩
⎪⎭
⎧ 1 ∂uθ ⎫ ⎧ 1 ⎫
⎨
⎬=⎨ ⎬
⎩ r ∂θ ⎭ ⎩ t ⎭
⎧ length ⎫
⎧ ∂u z ⎫ ⎪⎪ time ⎪⎪ ⎧ 1 ⎫
⎨
⎬=⎨
⎬=⎨
⎬
⎩ ∂z ⎭ ⎪ length ⎪ ⎩ time ⎭
⎩⎪
⎭⎪
⎧ ∂u z ⎫ ⎧ 1 ⎫
⎨
⎬=⎨ ⎬
⎩ ∂z ⎭ ⎩ t ⎭
Indeed, all three additive terms have the same dimensions, namely {t-1}.
Discussion
If the dimensions of any of the terms were different from the others, it would be a sure sign that an error
was made somewhere in deriving or copying the equation.
7-13
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-24
Solution
We are to determine the primary dimensions of each additive term in the equation, and we are to verify that
the equation is dimensionally homogeneous.
Analysis
The primary dimensions of heat transfer rate are energy/time. The primary dimensions of mass flow rate are
mass/time, and those of specific heat are energy/mass⋅temperature, as found in Problem 7-14. Thus each term in the
equation can be written in terms of primary dimensions,
⎧ mL2
⎧ energy ⎫ ⎪⎪ t 2
Q = ⎨
⎬=⎨
⎩ time ⎭ ⎪ t
⎩⎪
{}
⎫
2
⎪⎪ ⎧ mL ⎫
⎬=⎨ 3 ⎬
⎪ ⎩ t ⎭
⎭⎪
⎧
⎫
{Q } = ⎨ mL
⎬
t
⎩
2
3
⎭
T }
{mC
⎧
⎫
mL2
2
2
⎧ mass
⎫ ⎪⎪ m
energy
⎪⎪ ⎧ mL ⎫
=⎨
×
× temperature ⎬ = ⎨ × t × T ⎬ = ⎨ 3 ⎬
⎩ time mass × temperature
⎭ ⎪ t m×T
⎪ ⎩ t ⎭
⎪⎩
⎪⎭
mL
T }=⎨
{mC
⎬
t
T }
{mC
⎧
⎫
mL2
⎪ ⎧ mL2 ⎫
2
⎧ mass
⎫ ⎪⎪ m
energy
⎪
=⎨
×
× temperature ⎬ = ⎨ × t × T ⎬ = ⎨ 3 ⎬
⎩ time mass × temperature
⎭ ⎪ t m×T
⎪ ⎩ t ⎭
⎩⎪
⎭⎪
mL
T }=⎨
{mC
⎬
t
p out
p in
⎧
p out
⎩
2
3
⎧
p in
⎩
⎫
⎭
2
3
⎫
⎭
Indeed, all three additive terms have the same dimensions, namely {m1 L2 t-3}.
Discussion
We could also have left the temperature difference in parentheses as a temperature difference (same
dimensions as the individual temperatures), and treated the equation as having only two terms.
7-25
Solution
We are to determine the primary dimensions of each additive term, and we are to verify that the equation is
dimensionally homogeneous.
Analysis
The primary dimensions of the time derivative (d/dt) are 1/time. The primary dimensions of density are
mass/length3, those of volume are length3, those of area are length2, and those of velocity are length/time. The primary
G
G
dimensions of unit vector n are unity, i.e. {1} (in other words n has no dimensions). Finally, the primary dimensions of b,
which is defined as B per unit mass, are {B/m}. Thus each term in the equation can be written in terms of primary
dimensions,
⎧ dBsys ⎫ ⎧ B ⎫
⎨
⎬=⎨
⎬
⎩ dt ⎭ ⎩ time ⎭
⎧d
⎨
⎩ dt
{∫
CS
∫
CV
⎧ dBsys ⎫ ⎧ B ⎫
⎨
⎬=⎨ ⎬
⎩ dt ⎭ ⎩ t ⎭
⎧ 1
⎫
B
mass
×
×
× length 3 ⎬
3
⎩ time length mass
⎭
⎫
ρ bdV ⎬ = ⎨
G G
⎭
}
⎧ mass
⎫
B
length
×
×
× 1× length 2 ⎬
3
⎩ length mass time
⎭
ρ bVr ⋅ ndA = ⎨
⎧d
⎨
⎩ dt
∫
{∫
ρ bVr ⋅ ndA = ⎨ ⎬
CS
CV
⎫
⎭
⎧B⎫
⎩t⎭
}
⎧B⎫
⎩t⎭
ρ bdV ⎬ = ⎨ ⎬
G G
Indeed, all three additive terms have the same dimensions, namely {B t-1}.
Discussion
The RTT for property B has dimensions of rate of change of B.
7-14
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-26
Solution
We are to determine the primary dimensions of the first three additive term, and we are to verify that those
terms are dimensionally homogeneous. Then we are to evaluate the dimensions of the adsorption coefficient.
Analysis
The primary dimensions of the time derivative (d/dt) are 1/time. Those of As are length2, those of V are
length3, those of c are mass/length3, and those of V are length3/time. Thus the primary dimensions of the first three terms
are
⎧
⎨V
⎩
mass ⎫
⎧
3 ⎪
⎪
dc ⎫ ⎪
⎧ mass ⎫
3 length ⎪
⎬ = ⎨length
⎬=⎨
⎬
time ⎪ ⎩ time ⎭
dt ⎭ ⎪
⎪⎭
⎩⎪
{S} = ⎧⎨
{V c} = ⎧⎨⎩ length
time
3
⎧ dc ⎫ ⎧ m ⎫
⎨V ⎬ = ⎨ ⎬
⎩ dt ⎭ ⎩ t ⎭
mass ⎫
⎬
⎩ time ⎭
{S} = ⎧⎨
mass ⎫ ⎧ mass ⎫
⎬=⎨
⎬
length 3 ⎭ ⎩ time ⎭
{V c} = ⎧⎨⎩ mt ⎫⎬⎭
×
m⎫
⎬
⎩t ⎭
Indeed, the first three additive terms have the same dimensions, namely {m1 t-1}. Since the equation must be dimensionally
homogeneous, the last term must have the same dimensions as well. We use this fact to find the dimensions of kw,
mass ⎫
{cAs kw } = ⎧⎨
⎬
⎩ time ⎭
⎫
mass
⎧ mass ⎫ ⎧
⎪⎪ time ⎪⎪ ⎪⎪
⎪⎪
time
{k w } = ⎨
⎬=⎨
⎬
⎪ cAs ⎪ ⎪ mass 3 × length 2 ⎪
⎩⎪
⎭⎪ ⎩⎪ length
⎭⎪
{kw } = ⎧⎨
L⎫
⎬
⎩t⎭
Or, in exponent form, {kw} = {L1 t-1}. The dimensions of wall adsorption coefficient are those of velocity.
Discussion
In fact, some authors call kw a “deposition velocity”.
7-15
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Nondimensionalization of Equations
7-27C
Solution
Analysis
problem.
We are to give the primary reason for nondimensionalizing an equation.
The primary reason for nondimensionalizing an equation is to reduce the number of parameters in the
Discussion
As shown in the examples in the text, nondimensionalization of an equation reduces the number of
independent parameters in the problem, simplifying the analysis.
7-28
Solution
We are to nondimensionalize all the variables, and then re-write the equation in nondimensionalized form.
Assumptions
1 The air in the room is well mixed so that c is only a function of time.
Analysis
(a) We nondimensionalize the variables by inspection according to their dimensions,
Nondimensionalized variables:
A
c
L2
S
V
V
, t* = t 3 , As * = 2s , k w * = k w , and S * =
V * = 3 , c* =
climit
L
L
L
V
climitV
(b) We substitute these into the equation to generate the nondimensionalized equation,
V *L3
d ( c*climit )
− V c*c − ( c*c ) A *L2 ⎛⎜ k * V
=
S
c
V
*
s
w
limit
limit
limit
⎜
L2
⎛ L3 ⎞
⎝
d ⎜ t* ⎟
⎝ V ⎠
(
)
⎞
⎟⎟
⎠
(1)
We notice that every term in Eq. 1 contains the quantity V climit . We divide every term by this quantity to get a
nondimensionalized form of the equation,
Nondimensionalized equation:
V*
dc*
= S * − c* − c*As *kw *
dt*
No dimensionless groups have arisen in this nondimensionalization.
Discussion
Since all the characteristic scales disappear, no dimensionless groups have arisen. Since there are no
dimensionless parameters, one solution in nondimensionalized variables is valid for all combinations of L, V , and climit.
7-16
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-29
Solution
We are to nondimensionalize the equation, and identify the dimensionless parameters that appear in the
nondimensionalized equation.
Assumptions
1 The flow is steady. 2 The flow is incompressible.
Analysis
We plug the nondimensionalized variables into the equation. For example, u = u*U and x = x*L in the first
term. The result is
U ∂u * U ∂v * U ∂w *
+
+
=0
L ∂x * L ∂y * L ∂z *
or, after simplifying,
Nondimensionalized incompressible flow relationship:
∂u * ∂v * ∂w *
+
+
=0
∂x * ∂y * ∂z *
(1)
There are no nondimensional parameters in the nondimensionalized equation. The original equation comes from pure
kinematics – there are no fluid properties involved in the equation, and therefore it is not surprising that no nondimensional
parameters appear in the nondimensionalized form of the equation, Eq. 1.
Discussion
We show in Chap. 9 that the equation given in this problem is the differential equation for conservation of
mass for an incompressible flow field – the incompressible continuity equation.
7-30
Solution
We are to nondimensionalize the equation of motion and identify the dimensionless parameters that appear
in the nondimensionalized equation.
Analysis
is
We plug in the nondimensionalized variables. For example, u = u*V and x = x*L in the first term. The result
L3 f 1 DV * V ∂u * V ∂v * V ∂w *
=
+
+
L3 V * Dt * L ∂x * L ∂y * L ∂z *
or, after simplifying,
⎛ fL ⎞ 1 DV * ∂u * ∂v * ∂w *
=
+
+
⎜ ⎟
⎝ V ⎠ V * Dt * ∂x * ∂y * ∂z *
(1)
We recognize the nondimensional parameter in parentheses in Eq. 1 as St, the Strouhal number. We can re-write Eq. 1 as
Nondimensionalized oscillating compressible flow relationship:
1 DV * ∂u * ∂v * ∂w *
St
=
+
+
V * Dt * ∂x * ∂y * ∂z *
Discussion
We show in Chap. 9 that the given equation of motion is the differential equation for conservation of mass
for an unsteady, compressible flow field – the general continuity equation. We may also use angular frequency ω (radians
per second) in place of physical frequency f (cycles per second), with the same result.
7-17
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-31
Solution
We are to determine the primary dimensions of the stream function, nondimensionalize the variables, and
then re-write the definition of ψ in nondimensionalized form.
Assumptions
1 The flow is incompressible. 2 The flow is two-dimensional in the x-y plane.
Analysis
(a) We use that fact that all equations must be dimensionally homogeneous. We solve for the dimensions of
ψ,
Primary dimensions of stream function:
2
L
⎫ ⎧L ⎫
× L⎬ = ⎨ ⎬
⎩t
⎭ ⎩ t ⎭
{ψ } = {u} × { y} = ⎨⎧
Or, in exponent form, {ψ} = {L2 t-1}.
(b) We nondimensionalize the variables by inspection according to their dimensions,
Nondimensionalized variables:
x
y
x* =
y* =
L
L
u* = u
t
L
v* = v
t
L
ψ* =ψ
t
L2
(c) We generate the nondimensionalized equations,
⎛ L2 ⎞
∂ψ * ⎜ ⎟
⎛ L⎞
⎝ t ⎠
u *⎜ ⎟ =
*
t
y
∂
( L)
⎝ ⎠
⎛ L2 ⎞
∂ψ * ⎜ ⎟
⎛ L⎞
⎝ t ⎠
v *⎜ ⎟ = −
*
t
x
∂
( L)
⎝ ⎠
We notice that every term in both parts of the above equation contains the ratio L/t. We divide every term by L/t to get the
final nondimensionalized form of the equations,
Nondimensionalized stream function equations:
u* =
∂ψ *
∂y *
v* = −
∂ψ *
∂x *
No dimensionless groups have arisen in this nondimensionalization.
Discussion
Since all the nondimensionalized variables scale with L and t, no dimensionless groups have arisen.
7-18
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-32
Solution
We are to nondimensionalize the equation of motion and identify the dimensionless parameters that appear
in the nondimensionalized equation.
G
G
Analysis
We plug the nondimensionalized variables into the equation. For example, t = t*/ω and V = V∞V * in the
first term on the right hand side. The result is
G
G
∂V * U 2 G G G
2
V * ⋅∇ * V *
+
ω L F / m * = ωU
L
∂t *
(
)
(
)
or, after simplifying by multiplying each term by L/ V∞2,
G
2
G G G
⎛ωL ⎞ G
⎛ ω L ⎞ ∂V *
+ V * ⋅∇ * V *
⎜
⎟ F /m *= ⎜
⎟
⎝ V∞ ⎠
⎝ V∞ ⎠ ∂t *
(
)
(
)
(1)
We recognize the nondimensional parameter in parentheses in Eq. 1 as St, the Strouhal number. We re-write Eq. 1 as
Nondimensionalized Newton’s second law for incompressible oscillatory
G
G
G G G
∂V *
2
+ V * ⋅∇ * V *
flow:
(St ) F / m * = (St )
∂t *
(
)
(
)
Discussion
We used angular frequency ω in this problem. The same result would be obtained if we used physical
frequency. Equation 1 is the basis for forming the differential equation for conservation of linear momentum for an
unsteady, incompressible flow field.
7-33
Solution
We are to nondimensionalize the Bernoulli equation and generate an expression for the pressure coefficient.
Assumptions
other terms.
1 The flow is incompressible. 2 Gravitational terms in the Bernoulli equation are negligible compared to the
Analysis
We nondimensionalize the equation by dividing each term by the dynamic pressure,
Nondimensionalization:
P
1
ρV∞ 2
2
+
1
ρV∞ 2 ,
2
P∞
V2
=
+1
2
1
V∞
ρV∞ 2
2
Rearranging,
Pressure coefficient:
Cp =
P − P∞
V2
= 1− 2
1
V∞
ρV∞ 2
2
Discussion
Pressure coefficient is a useful dimensionless parameter that is inversely related to local air speed – as local
air speed V increases, Cp decreases.
7-19
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Dimensional Analysis and Similarity
7-34C
Solution
We are to list the three primary purposes of dimensional analysis.
Analysis
The three primary purposes of dimensional analysis are:
1. To generate nondimensional parameters that help in the design of experiments and in the reporting of
experimental results.
2. To obtain scaling laws so that prototype performance can be predicted from model performance.
3. To (sometimes) predict trends in the relationship between parameters.
Discussion
Dimensional analysis is most useful for difficult problems that cannot be solved analytically.
7-35C
Solution
prototype.
We are to list and describe the three necessary conditions for complete similarity between a model and a
Analysis
The three necessary conditions for complete similarity between a model and a prototype are:
1. Geometric similarity – the model must be the same shape as the prototype, but scaled by some constant scale
factor.
2. Kinematic similarity – the velocity at any point in the model flow must be proportional (by a constant scale
factor) to the velocity at the corresponding point in the prototype flow.
3. Dynamic similarity – all forces in the model flow scale by a constant factor to corresponding forces in the
prototype flow.
Discussion
Complete similarity is achievable only when all three of the above similarity conditions are met.
7-36
Solution
For a scale model of a submarine being tested in air, we are to calculate the wind tunnel speed required to
achieve similarity with the prototype submarine that moves through water at a given speed.
Assumptions 1 Compressibility of the air is assumed to be negligible. 2 The wind tunnel walls are far enough away so as
to not interfere with the aerodynamic drag on the model sub. 3 The model is geometrically similar to the prototype.
Properties
For water at T = 15oC and atmospheric pressure, ρ = 999.1 kg/m3 and μ = 1.138 × 10-3 kg/m⋅s. For air at T =
o
25 C and atmospheric pressure, ρ = 1.184 kg/m3 and μ = 1.849 × 10-5 kg/m⋅s.
Analysis
Similarity is achieved when the Reynolds number of the model is equal to that of the prototype,
Re m =
Similarity:
ρ pVp Lp
ρ mVm Lm
= Re p =
μm
μp
(1)
We solve Eq. 1 for the unknown wind tunnel speed,
⎛μ
Vm = Vp ⎜ m
⎜ μp
⎝
⎞ ⎛ ρ p ⎞ ⎛ Lp ⎞
⎟⎟ ⎜
⎟⎜
⎟
⎠ ⎝ ρ m ⎠ ⎝ Lm ⎠
⎛ 1.849 × 10−5 kg/m ⋅ s ⎞ ⎛ 999.1 kg/m3 ⎞
8 = 61.4 m/s
= ( 0.560 m/s ) ⎜
⎟⎜
3 ⎟( )
−3
⎝ 1.138 × 10 kg/m ⋅ s ⎠ ⎝ 1.184 kg/m ⎠
Discussion
At this air temperature, the speed of sound is around 346 m/s. Thus the Mach number in the wind tunnel is
equal to 61.4/346 = 0.177. This is sufficiently low that the incompressible flow approximation is reasonable.
7-20
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-37
Solution
For a scale model of a submarine being tested in air, we are to calculate the wind tunnel speed required to
achieve similarity with the prototype submarine that moves through water at a given speed.
Assumptions 1 Compressibility of the air is assumed to be negligible. 2 The wind tunnel walls are far enough away so as
to not interfere with the aerodynamic drag on the model sub. 3 The model is geometrically similar to the prototype.
Properties
For water at T = 15oC and atmospheric pressure, ρ = 999.1 kg/m3 and μ = 1.138 × 10-3 kg/m⋅s. For air at T =
o
25 C and atmospheric pressure, ρ = 1.184 kg/m3 and μ = 1.849 × 10-5 kg/m⋅s.
Analysis
Similarity is achieved when the Reynolds number of the model is equal to that of the prototype,
Rem =
Similarity:
ρ pVp Lp
ρ mVm Lm
= Re p =
μm
μp
(1)
We solve Eq. 1 for the unknown wind tunnel speed,
⎛μ
Vm = Vp ⎜ m
⎜
⎝ μp
⎞ ⎛ ρ p ⎞ ⎛ Lp ⎞
⎛ 1.849 × 10 −5 kg/m ⋅ s ⎞⎛ 999.1 kg/m 3 ⎞
= 0.560 m/s ⎜
24 ) = 184 m/s
⎟⎜
⎟
⎜
⎟
⎟⎜
3 ⎟(
−3
⎟
⎝ 1.138 × 10 kg/m ⋅ s ⎠⎝ 1.184 kg/m ⎠
⎠ ⎝ ρ m ⎠ ⎝ Lm ⎠
At this air temperature, the speed of sound is around 346 m/s. Thus the Mach number in the wind tunnel is equal to
184/346 = 0.532. The Mach number is sufficiently high that the incompressible flow approximation is not
reasonable. The wind tunnel should be run at a flow speed at which the Mach number is less than one-third of the
speed of sound. At this lower speed, the Reynolds number of the model will be too small, but the results may still be
usable, either by extrapolation to higher Re, or if we are fortunate enough to have Reynolds number independence,
as discussed in Section 7-5.
Discussion
It is also unlikely that a small instructional wind tunnel can achieve such a high speed.
7-21
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-38E
Solution
For a prototype parachute and its model we are to calculate drag coefficient, and determine the wind tunnel
speed that ensures dynamic similarity. Then we are to estimate the aerodynamic drag on the model.
Assumptions
1 The model is geometrically similar to the prototype.
Properties
For air at 60oF and standard atmospheric pressure, ρ = 0.07633 lbm/ft3 and μ = 1.213 × 10-5 lbm/ft⋅s.
Analysis
(a) The aerodynamic drag on the prototype parachute is equal to the total weight. We can then easily
calculate the drag coefficient CD,
Drag coefficient:
CD =
FD ,p
1
2
ρ pVp 2 Ap
230 lbf
=
1
2
( 0.07633 lbm/ft ) ( 20 ft/s ) π (
3
2
24 ft )
2
⎛ 32.2 lbm ft ⎞
⎜ lbf s 2 ⎟ = 1.07
⎝
⎠
4
(b) We must match model and prototype Reynolds numbers in order to achieve dynamic similarity,
Rem =
Similarity:
ρ pVp Lp
ρ mVm Lm
= Re p =
μm
μp
(1)
We solve Eq. 1 for the unknown wind tunnel speed,
Wind tunnel speed:
⎛μ
Vm = Vp ⎜ m
⎜ μp
⎝
⎞ ⎛ ρ p ⎞ ⎛ Lp ⎞
⎟⎟ ⎜
⎟⎜
⎟ = ( 20 ft/s )(1)(1)(12 ) = 240 ft/s
⎠ ⎝ ρ m ⎠ ⎝ Lm ⎠
(2)
(c) As discussed in the text, if the fluid is the same and dynamic similarity between the model and the prototype is
achieved, the aerodynamic drag force on the model is the same as that on the prototype. Thus,
Aerodynamic drag on model:
FD ,m = FD ,p = 230 lbf
(3)
Discussion
We should check that the wind tunnel speed of Eq. 2 is not too high that the incompressibility
approximation becomes invalid. The Mach number at this speed is about 240/1120 = 0.214. Since this is less than 0.3,
compressibility is not an issue in this model test. The drag force on the model is quite large, and a fairly hefty drag balance
must be available to measure such a large force.
7-22
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-39
Solution
We are to discuss why one would pressurize a wind tunnel.
Analysis
As we see in some of the example problems and homework problems in this chapter, it is often difficult to
achieve a high-enough wind tunnel speed to match the Reynolds number between a small model and a large prototype.
Even if we were able to match the speed, the Mach number would often be too high. A pressurized wind tunnel has higher
density air. At the same Reynolds number, the larger density leads to a lower air speed requirement. In other words, a
pressurized wind tunnel can achieve higher Reynolds numbers for the same scale model.
If the pressure were to be increased by a factor of 1.5, the air density would also go up by a factor of 1.5 (ideal gas
law), assuming that the air temperature remains constant. Then the Reynolds number, Re = ρVL/μ, would go up by
approximately 1.5. Note that we are also assuming that the viscosity does not change significantly with pressure, which is a
reasonable assumption.
Discussion
The speed of sound is not a strong function of pressure, so Mach number is not affected significantly by
pressurizing the wind tunnel. However, the power requirement for the wind tunnel blower increases significantly as air
density is increased, so this must be taken into account when designing the wind tunnel.
7-40
Solution
We are to estimate the drag on a prototype submarine in water, based on aerodynamic drag measurements
performed in a wind tunnel.
Assumptions 1 The model is geometrically similar. 2 The wind tunnel is run at conditions which ensure similarity
between model and prototype.
Properties
For water at T = 15oC and atmospheric pressure, ρ = 999.1 kg/m3 and μ = 1.138 × 10-3 kg/m⋅s. For air at T =
o
25 C and atmospheric pressure, ρ = 1.184 kg/m3 and μ = 1.849 × 10-5 kg/m⋅s.
Analysis
Since the Reynolds numbers have been matched, the nondimensionalized drag coefficient of the model
equals that of the prototype,
FD ,m
ρ mVm Lm
2
2
=
FD ,p
ρ pVp 2 Lp 2
(1)
We solve Eq. 1 for the unknown aerodynamic drag force on the prototype, FD,p,
2
⎛ ρ p ⎞ ⎛ Vp ⎞ ⎛ Lp ⎞
⎛ 999.1 kg/m ⋅ s ⎞ ⎛ 0.560 m/s ⎞
2
= FD ,m ⎜
(8) = 10.3 N
⎟⎜
⎟ ⎜
⎟ = ( 2.3 N ) ⎜
⎟⎜
⎟
⎝ 1.184 kg/m ⋅ s ⎠ ⎝ 61.4 m/s ⎠
⎝ ρ m ⎠ ⎝ Vm ⎠ ⎝ Lm ⎠
2
FD ,p
2
where we have used the wind tunnel speed calculated in Problem 7-36.
Discussion
Although the prototype moves at a much slower speed than the model, the density of water is much higher
than that of air, and the prototype is eight times larger than the model. When all of these factors are combined, the drag
force on the prototype is much larger than that on the model.
7-23
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-41E
Solution
The concept of similarity will be utilized to determine the speed of the wind tunnel.
Assumptions 1 Compressibility of the air is ignored (the validity of this assumption will be discussed later). 2 The wind
tunnel walls are far enough away so as to not interfere with the aerodynamic drag on the model car. 3 The model is
geometrically similar to the prototype. 4 Both the air in the wind tunnel and the air flowing over the prototype car are at
standard atmospheric pressure.
Properties
For air at T = 25oC and atmospheric pressure, ρ = 1.184 kg/m3 and μ = 1.849 × 10-5 kg/m⋅s.
Analysis
Since there is only one independent Π in this problem, similarity is achieved if Π2,m = Π2,p, where Π2 is the
Reynolds number. Thus, we can write
Π 2,m = Re m =
ρ pVp Lp
ρ mVm Lm
= Π 2,p = Re p =
μm
μp
which can be solved for the unknown wind tunnel speed for the model tests, Vm,
⎛μ
Vm = Vp ⎜ m
⎜ μp
⎝
⎞ ⎛ ρ p ⎞ ⎛ Lp ⎞
⎟⎟ ⎜
⎟⎜
⎟ = ( 60.0 mph )(1)(1)( 4 ) = 240 mph
⎠ ⎝ ρ m ⎠ ⎝ Lm ⎠
Thus, to ensure similarity, the wind tunnel should be run at 240 miles per hour (to three significant digits).
Discussion
This speed is quite high, and the wind tunnel may not be able to run at that speed. We were never given the
actual length of either car, but the ratio of Lp to Lm is known because the prototype is four times larger than the scale model.
The problem statement contains a mixture of SI and English units, but it does not matter since we use ratios in the algebra.
7-42E
Solution
wind tunnel.
We are to estimate the drag on a prototype car, based on aerodynamic drag measurements performed in a
Assumptions 1 The model is geometrically similar. 2 The wind tunnel is run at conditions which ensure similarity
between model and prototype.
Properties
For air at T = 25oC and atmospheric pressure, ρ = 1.184 kg/m3 and μ = 1.849 × 10-5 kg/m⋅s.
Analysis
Following the example in the text, since the Reynolds numbers have been matched, the nondimensionalized
drag coefficient of the model equals that of the prototype,
FD ,m
ρ mVm Lm
2
2
=
FD ,p
ρ pVp 2 Lp 2
(1)
We solve Eq. 1 for the unknown aerodynamic drag force on the prototype, FD,p,
⎛ ρ p ⎞ ⎛ Vp ⎞ ⎛ Lp ⎞
⎛ 60.0 mph ⎞
2
= FD ,m ⎜
⎟⎜
⎟ ⎜
⎟ = ( 36.5 lbf )(1) ⎜
⎟ ( 4 ) = 36.5 lbf
⎝ 240 mph ⎠
⎝ ρ m ⎠ ⎝ Vm ⎠ ⎝ Lm ⎠
2
FD ,p
2
2
where we have used the wind tunnel speed calculated in the previous problem.
Discussion
Since the air properties of the wind tunnel are identical to those of the air flowing around the prototype car,
it turns out that the aerodynamic drag force on the prototype is the same as that on the model. This would not be the case if
the wind tunnel air were at a different temperature or pressure compared to that of the prototype.
7-24
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-43
Solution
We are to discuss whether cold or hot air in a wind tunnel is better, and we are to support our answer by
comparing air at two given temperatures.
Properties
For air at atmospheric pressure and at T = 10oC, ρ = 1.246 kg/m3 and μ = 1.778 × 10-5 kg/m⋅s. At T = 50oC,
3
ρ = 1.092 kg/m and μ = 1.963 × 10-5 kg/m⋅s.
Analysis
As we see in some of the example problems and homework problems in this chapter, it is often difficult to
achieve a high-enough wind tunnel speed to match the Reynolds number between a small model and a large prototype.
Even if we were able to match the speed, the Mach number would often be too high. Cold air has higher density than warm
air. In addition, the viscosity of cold air is lower than that of hot air. Thus, at the same Reynolds number, the colder air
leads to a lower air speed requirement. In other words, a cold wind tunnel can achieve higher Reynolds numbers than
can a hot wind tunnel for the same scale model, all else being equal. We support our conclusion by comparing air at two
temperatures,
Comparison of Reynolds numbers:
ρcoldVL
Re cold
μcold
ρ
μ
1.246 kg/m3 1.963 × 10−5 kg/m ⋅ s
=
= cold hot =
= 1.26
ρ hotVL
Re hot
ρ hot μcold 1.092 kg/m3 1.778 × 10−5 kg/m ⋅ s
μhot
Thus we see that the colder wind tunnel can achieve approximately 26% higher Reynolds number, all else being
equal.
Discussion
There are other issues however. First of all, the denser air of the cold wind tunnel is harder to pump – the
cold wind tunnel may not be able to achieve the same wind speed as the hot wind tunnel. Furthermore, the speed of sound
is proportional to the square root of temperature. Thus, at colder temperatures, the Mach number is higher than at warmer
temperatures for the same value of V, and compressibility effects are therefore more significant at lower temperatures.
7-44
Solution
We are to calculate the speed and angular velocity (rpm) of a spinning baseball in a water channel such that
flow conditions are dynamically similar to that of the actual baseball moving and spinning in air.
Properties
For air at T = 20oC and atmospheric pressure, ρ = 1.204 kg/m3 and μ = 1.825 × 10-5 kg/m⋅s. For water at T =
o
20 C and atmospheric pressure, ρ = 998.0 kg/m3 and μ = 1.002 × 10-3 kg/m⋅s.
Analysis
The model (in the water) and the prototype (in the air) are actually the same baseball, so their characteristic
lengths are equal, Lm = Lp. We match Reynolds number,
Re m =
ρ pVp Lp
ρ mVm Lm
= Re p =
μm
μp
(1)
and solve for the required water tunnel speed for the model tests, Vm,
⎛μ
Vm = Vp ⎜ m
⎜ μp
⎝
⎞ ⎛ ρ p ⎞⎛ Lp ⎞
⎛ 1.002 × 10 −3 kg/m ⋅ s ⎞ ⎛ 1.204 kg/m3 ⎞
1 = 5.30 mph
= ( 80.0 mph ) ⎜
⎟⎜
⎟⎜
⎟
⎟⎜
3 ⎟( )
−5
⎟ ρ m Lm
⎝ 1.825 × 10 kg/m ⋅ s ⎠ ⎝ 998.0 kg/m ⎠
⎠⎝
⎠
⎠⎝
(2)
We also match Strouhal numbers, recognizing that n is proportional to f,
St m =
f p Lp
f m Lm
= St p =
Vm
Vp
→
nm Lm np Lp
=
Vm
Vp
(3)
from which we solve for the required spin rate in the water tunnel,
⎛ Lp
nm = np ⎜
⎝ Lm
⎞ ⎛ Vm
⎟ ⎜⎜
⎠ ⎝ Vp
⎞
⎛ 5.30 mph ⎞
⎟ = ( 300 rpm )(1) ⎜
⎟ = 19.9 rpm
⎟
⎝ 80.0 mph ⎠
⎠
(4)
Discussion
Because of the difference in fluid properties between air and water, the required water tunnel speed is much
lower than that in air. In addition, the spin rate is much lower, making flow visualization easier.
7-25
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Dimensionless Parameters and the Method of Repeating Variables
7-45
Solution
We are to verify that the Archimedes number is dimensionless.
Analysis
Archimedes number is defined as
Archimedes number:
Ar =
ρ s gL3
( ρs − ρ )
μ2
(1)
We know the primary dimensions of density, gravitational acceleration, length, and viscosity. Thus,
Primary dimensions of Archimedes number:
⎧m L 3 ⎫
⎪ 3 2 L m⎪
{Ar} = ⎪⎨ L t 2 3 ⎪⎬ = {1}
L ⎪
⎪ m
⎪⎭
⎩⎪ L2 t 2
(2)
Discussion
If the primary dimensions were not unity, we would assume that we made an error in the dimensions of one
or more of the parameters.
7-46
Solution
We are to verify that the Grashof number is dimensionless.
Analysis
Grashof number is defined as
Grashof number:
Gr =
g β ΔT L3 ρ 2
μ2
(1)
We know the primary dimensions of density, gravitational acceleration, length, temperature, and viscosity. The dimensions
of coefficient of thermal expansion β are 1/temperature. Thus,
Primary dimensions of Grashof number:
⎧ L 1 3 m2 ⎫
⎪⎪ 2 TL 6 ⎪⎪
Gr
=
{ } ⎨ t T 2 L ⎬ = {1}
m
⎪
⎪
⎪⎭
L2 t 2
⎩⎪
(2)
Discussion
If the primary dimensions were not unity, we would assume that we made an error in the dimensions of one
or more of the parameters.
7-26
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-47
Solution
We are to verify that the Rayleigh number is dimensionless, and determine what other established
nondimensional parameter is formed by the ratio of Ra and Gr.
Analysis
Rayleigh number is defined as
Ra =
Rayleigh number:
g β ΔT L3 ρ 2 c p
kμ
(1)
We know the primary dimensions of density, gravitational acceleration, length, temperature, and viscosity. The dimensions
of coefficient of thermal expansion β are 1/temperature, those of specific heat cp are length2/time2⋅temperature (Problem 714), and those of thermal conductivity k are mass⋅length/time3⋅temperature. Thus,
Primary dimensions of Rayleigh number:
⎧ L 1 3 m 2 L2 ⎫
⎪ 2 TL 6 2 ⎪⎪
L t T = {1}
{Ra} = ⎪⎨ t T mL m
⎬
⎪
⎪
t 3 T Lt
⎪⎭
⎩⎪
(2)
We take the ratio of Ra and Gr:
g β ΔT L3 ρ 2 c p
Ratio of Rayleigh number and Grashof number:
Ra
kμ
=
Gr
g β ΔT L3 ρ 2
=
cp μ
k
(3)
μ2
We recognize Eq. 3 as the Prandtl number,
Prandtl number:
Pr =
Ra c p μ ρ c p μ ν
=
=
=
Gr
ρk
α
k
(4)
Discussion
Many of the established nondimensional parameters are formed by the ratio or product of two (or more)
other established nondimensional parameters.
7-27
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-48
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are five parameters in this problem; n = 5,
h = f (ω , ρ , g , R )
List of relevant parameters:
n=5
(1)
Step 2 The primary dimensions of each parameter are listed,
h
ω
ρ
g
R
{L }
{t }
{m L }
{L t }
{L }
−1
1
1 −3
1 −2
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. Following the guidelines outlined in this chapter, we
elect not to pick the viscosity. We choose
ω, ρ, and R
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = hω a1 ρ b1 R c1
{( L )( t
1
−1
) (m L ) (L )
a1
1 −3
b1
1
c1
}
mass:
{m } = {m }
0 = b1
b1 = 0
time:
{t } = {t }
0 = − a1
a1 = 0
0 = 1 − 3b1 + c1
c1 = −1
0
b1
− a1
0
{L } = { L L
length:
1 −3b1
0
Lc1
}
The dependent Π is thus
Π 1:
Π1 =
h
R
The second Pi (the only independent Π in this problem) is generated:
{Π 2 } =
Π 2 = gω a2 ρ b2 R c2
mass:
{m } = {m }
time:
{ t } = {t
0
0
b2
−2 − a2
t
}
{( L t
1 −2
)( t ) ( m L ) ( L )
−1
a2
1 −3
b2
1
c2
}
0 = b2
b2 = 0
0 = −2 − a2
a2 = −2
7-28
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
length:
{L } = {L L
0
1 −3b2
Lc2
}
c2 = −1
0 = 1 − 3b2 + c2
0 = 1 + c2
which yields
Π 2:
Π2 =
g
ω2R
If we take Π2 to the power –1/2 and recognize that ωR is the speed of the rim, we see that Π2 can be modified into a
Froude number,
Modified Π2:
Π 2 = Fr =
ωR
gR
Step 6 We write the final functional relationship as
Relationship between Πs:
h
= f ( Fr )
R
(2)
Discussion
In the generation of the first Π, h and R have the same dimensions. Thus, we could have immediately
written down the result, Π1 = h/R. Notice that density ρ does not appear in the result. Thus, density is not a relevant
parameter after all.
7-29
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-49
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are seven parameters in this problem; n = 7,
h = f ( ω , ρ , g , R, t , μ )
List of relevant parameters:
n=7
(1)
Step 2 The primary dimensions of each parameter are listed,
h
ω
ρ
g
R
t
μ
{L }
{t }
{m L }
{L t }
{L }
{t }
{m L t }
−1
1
1 −3
1 −2
1
1
1 −1 −1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 7−3 = 4
Step 4 We need to choose three repeating parameters since j = 3. For convenience we choose the same repeating
parameters that we used in the previous problem,
ω, ρ, and R
Repeating parameters:
Step 5 The first two Πs are identical to those of the previous problem:
Π 1:
Π1 =
h
R
and
Π 2:
Π2 =
ωR
gR
where Π2 is identified as a form of the Froude number. The third Π is formed with time t. Since repeating parameter ω
has dimensions of 1/time, it is the only one that remains in the Π. Thus, without the formal algebra,
Π 3 = ωt
Π 3:
Finally, Π4 is generated with liquid viscosity,
{Π 4 } =
Π 4 = μω a4 ρ b4 R c4
mass:
{m } = {m m }
time:
{t } = { t
length:
0
1
0
{L } = { L
0
b4
−1 − a4
t
−1 −3b1
L
}
Lc1
}
{( m L t
1 −1 −1
)( t ) ( m L ) ( L )
a4
−1
1 −3
b4
1
c4
}
0 = 1 + b4
b4 = −1
0 = −1 − a4
a4 = −1
0 = −1 − 3b4 + c4
c4 = −2
c4 = 1 + 3b4
The final Π is thus
7-30
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Π 4:
Π4 =
μ
ρΩR 2
(2)
If we invert Π4 and recognize that ωR is the speed of the rim, it becomes clear that Π4 of Eq. 2 can be modified into a
Reynolds number,
Modified Π4:
ρω R 2
= Re
μ
(3)
h
= f ( Fr, ωt , Re )
R
(4)
Π4 =
Step 6 We write the final functional relationship as
Relationship between Πs:
Discussion
Notice that this time density ρ does appear in the result. There are other acceptable answers, but this one has
the most established dimensionless groups.
7-31
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-50
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are five parameters in this problem; n = 5,
f k = f (V , ρ , μ , D )
List of relevant parameters:
n=5
Step 2 The primary dimensions of each parameter are listed,
fk
V
ρ
μ
D
{t }
{L t }
{m L }
{m L t }
{L }
−1
1 −1
1 −3
1 −1 −1
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. Following the guidelines outlined in this chapter, we
elect not to pick the viscosity. We choose
V, ρ, and D
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = f kV a1 ρ b1 D c1
mass:
{m } = { m }
time:
{t } = { t
0
−1
)( L t ) ( m L ) ( L )
1 −1
t
}
{L } = {L L
Lc1
0
−1 − a1
a1
−3b1
}
a1
1 −3
b1
1
c1
}
0 = b1
b1 = 0
0 = −1 − a1
a1 = −1
0 = a1 − 3b1 + c1
c1 = 1
b1
0
length:
{( t
The dependent Π is thus
Π 1:
Π1 =
fk D
= St
V
where we have identified this Pi as the Strouhal number.
The second Pi (the only independent Π in this problem) is generated:
{Π 2 } =
Π 2 = μV a2 ρ b2 D c2
mass:
{m } = {m m }
time:
{t } = { t
0
0
1
b2
−1 − a2
t
}
{( m L t
1 −1 − 1
)( L t ) ( m L ) ( L )
1 −1
a2
1 −3
b2
1
c2
}
0 = 1 + b2
b2 = −1
0 = −1 − a2
a2 = −1
7-32
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
length:
{L } = {L
0
L L−3b2 Lc2
−1 a2
}
c2 = −1
0 = −1 + a2 − 3b2 + c2
0 = −1 − 1 + 3 + c2
which yields
Π 2:
Π2 =
μ
ρVD
We recognize this Π as the inverse of the Reynolds number. So, after inverting,
Modified Π2:
Π2 =
ρVD
= Reynolds number = Re
μ
Step 6 We write the final functional relationship as
Relationship between Πs:
St = f ( Re )
Discussion
We cannot tell from dimensional analysis the exact form of the functional relationship. However,
experiments verify that the Strouhal number is indeed a function of Reynolds number.
7-33
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-51
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are six parameters in this problem; n = 6,
f k = f (V , ρ , μ , D, c )
List of relevant parameters:
n=6
(1)
Step 2 The primary dimensions of each parameter are listed,
fk
V
ρ
μ
D
c
{t }
{L t }
{m L }
{m L t }
{L }
{L t }
−1
1 −1
1 −3
1 −1 −1
1
1 −1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 6−3 = 3
Step 4 We need to choose three repeating parameters since j = 3. Following the guidelines outlined in this chapter, we
elect not to pick the viscosity. We choose
V, ρ, and D
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = f kV a1 ρ b1 D c1
mass:
{m } = {m }
time:
{t } = { t
0
−1
)( L t ) ( m L ) ( L )
1 −1
t
}
{L } = {L L
Lc1
0
−1 − a1
a1
−3b1
}
a1
1 −3
b1
1
c1
}
0 = b1
b1 = 0
0 = −1 − a1
a1 = −1
0 = a1 − 3b1 + c1
c1 = 1
b1
0
length:
{( t
The dependent Π is thus
Π 1:
Π1 =
fk D
= St
V
where we have identified this Pi as the Strouhal number.
The second Pi (the first independent Π in this problem) is generated:
{Π 2 } =
Π 2 = μV a2 ρ b2 D c2
mass:
{m } = {m m }
time:
{t } = { t
0
0
1
b2
−1 − a2
t
}
{( m L t
1 −1 − 1
)( L t ) ( m L ) ( L )
1 −1
a2
1 −3
b2
1
c2
}
0 = 1 + b2
b2 = −1
0 = −1 − a2
a2 = −1
7-34
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
length:
{L } = {L
L L−3b2 Lc2
−1 a2
0
}
c2 = −1
0 = −1 + a2 − 3b2 + c2
0 = −1 − 1 + 3 + c2
which yields
Π 2:
Π2 =
μ
ρVD
We recognize this Π as the inverse of the Reynolds number. So, after inverting,
Modified Π2:
Π2 =
ρVD
= Reynolds number = Re
μ
The third Pi (the second independent Π in this problem) is generated:
{Π 3 } =
Π 3 = cV a3 ρ b3 D c3
mass:
{m } = {m }
time:
{t } = { t
length:
0
b3
0
{L } = {L L
0
−1 − a3
1 a3
t
}
L−3b3 Lc3
}
{( L t
1 −1
)( L t ) ( m L ) ( L )
1 −1
a3
1 −3
b3
1
c3
}
0 = b3
b3 = 0
0 = −1 − a3
a3 = −1
0 = 1 + a3 − 3b3 + c3
c3 = 0
0 = 1 − 1 + c3
which yields
Π 3:
Π3 =
c
V
We recognize this Π as the inverse of the Mach number. So, after inverting,
Modified Π3:
Π3 =
V
= Mach number = Ma
c
Step 6 We write the final functional relationship as
Relationship between Πs:
St = f ( Re, Ma )
Discussion
We have shown all the details. After you become comfortable with the method of repeating variables, you
can do some of the algebra in your head.
7-35
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-52
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are five parameters in this problem; n = 5,
W = f (ω , ρ , μ , D )
List of relevant parameters:
n=5
(1)
Step 2 The primary dimensions of each parameter are listed,
W
ω
ρ
μ
D
{m L t }
{t }
{m L }
{m L t }
{L }
1 2 −3
−1
1 −3
1 −1 −1
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. Following the guidelines outlined in this chapter, we
elect not to pick the viscosity. We choose
ω, ρ, and D
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = W ω a1 ρ b1 D c1
mass:
{m } = {m m }
time:
{t } = { t
0
1
0
−3 − a1
t
{L } = {L L
length:
0
b1
2
−3b1
}
Lc1
}
{( m L t
1 2 −3
)( t ) ( m L ) ( L )
−1
a1
1 −3
b1
1
c1
}
0 = 1 + b1
b1 = −1
0 = −3 − a1
a1 = −3
0 = 2 − 3b1 + c1
c1 = −5
The dependent Π is thus
Π1 =
Π 1:
W
= NP
ρ D5ω 3
where we have defined this Pi as the power number (Table 7-5).
The second Pi (the only independent Π in this problem) is generated:
{Π 2 } =
Π 2 = μω a2 ρ b2 D c2
mass:
{m } = {m m }
0
1
b2
{( m L t
1 −1 −1
)( t ) ( m L ) ( L )
−1
a2
1 −3
b2
1
c2
}
b2 = −1
0 = 1 + b2
7-36
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
{t } = { t
time:
length:
0
{L } = {L
0
−1 − a2
t
−1 −3b2
L
}
Lc2
}
0 = −1 − a2
a2 = −1
0 = −1 − 3b2 + c2
c2 = −2
0 = −1 + 3 + c2
which yields
Π 2:
Π2 =
μ
ρ D 2ω
Since Dω is the speed of the tip of the rotating stirrer blade, we recognize this Π as the inverse of a Reynolds number. So,
after inverting,
Modified Π2:
Π2 =
ρ D 2ω ρ ( Dω ) D
=
= Reynolds number = Re
μ
μ
Step 6 We write the final functional relationship as
N P = f ( Re )
Relationship between Πs:
(2)
Discussion
After some practice you should be able to do some of the algebra with the exponents in your head. Also, we
usually expect a type of Reynolds number when we combine viscosity with a density, a length, and some kind of speed, be
it angular speed or linear speed.
7-53
Solution
We are to determine the dimensionless relationship between the given parameters
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
The dimensional analysis is identical to the previous problem except that we add two additional
independent parameters, both of which have dimensions of length. The two Πs of the previous problem remain. We get two
additional Πs since n is now equal to 7 instead of 5. There is no need to go through all the algebra for the two additional Πs
– since their dimensions match those of one of the repeating variables (D), we know that all the exponents in the Π will be
zero except the exponent for D, which will be –1. The two additional Πs are
Π3 and Π4:
Π3 =
Dtank
D
Π4 =
hsurface
D
The final functional relationship is
Relationship between Πs:
D
h
⎛
⎞
N P = f ⎜ Re, tank , surface ⎟
D
D ⎠
⎝
(1)
Discussion
We could also manipulate our Πs so that we have other length ratios like hsurface/Dtank, etc. Any such
combination is acceptable.
7-37
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-54
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are five parameters in this problem; n = 5,
δ = f ( x, V , ρ , μ )
List of relevant parameters:
n=5
(1)
Step 2 The primary dimensions of each parameter are listed,
δ
x
{L }
{L }
1
ρ
V
μ
{L t } { m L } {m L t }
1 −1
1
1 −3
1 −1 −1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. We pick length scale x, density ρ, and freestream
velocity V.
x, ρ , and V
Repeating parameters:
Step 5 The Πs are generated. Note that for the first Π we can do the algebra in our heads since the relationship is
very simple. Namely, the dimensions of δ are identical to those of one of the repeating variables (x). In such a case
we know that all the exponents in the Π group are zero except the one for x, which is –1. The dependent Π is thus
Π 1:
Π1 =
δ
x
The second Π is formed with viscosity,
{Π 2 } =
Π 2 = μ x a ρ bV c
mass:
{m } = { m m }
time:
{t } = { t
length:
{L } = { L
0
1 −1 −1
)( L ) ( m L ) ( L t ) }
1
a
1 −3
b
1 −1
c
1
b
0 = 1+ b
b = −1
−1 − c
}
0 = −1 − c
c = −1
0 = −1 + a − 3b + c
0 = −1 + a + 3 − 1
a = −1
0
0
{( m L t
−1 a
t
L L−3b Lc
}
which yields
Π 2:
Π2 =
μ
ρVx
We recognize this Π as the inverse of the Reynolds number,
7-38
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Modified Π2 = Reynolds number based on x:
Π 2 = Re x
ρVx
μ
Step 6 We write the final functional relationship as
δ
Relationship between Πs:
x
= f ( Re x )
Discussion
We cannot determine the form of the relationship by purely dimensional reasoning since there are two Πs.
However, in Chap. 10 we shall see that for a laminar boundary layer, Π1 is proportional to the square root of Π2.
7-55
Solution
We are to create a scale for volume flow rate and then define an appropriate Richardson number.
Analysis
By “back of the envelope” reasoning (or by inspection), we define a volume flow rate scale as L2V. Then
the Richardson number can be defined as
Richardson number:
Ri =
L5 g Δρ
L5 g Δρ
Lg Δρ
=
=
2
2
2
ρV 2
ρV
ρ LV
(
)
(1)
Discussion
It is perhaps more clear from the form of Eq. 1 that Richardson number is a ratio of buoyancy forces to
inertial forces.
7-39
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-56
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are six parameters in this problem; n = 6,
u = f ( μ , V , h, ρ , y )
List of relevant parameters:
n=6
(1)
Step 2 The primary dimensions of each parameter are listed,
u
μ
V
h
ρ
y
{L t }
{m L t }
{L t }
{L }
{m L }
{L }
1 −1
1 −1 −1
1 −1
1 −3
1
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 6−3 = 3
Step 4 We need to choose three repeating parameters since j = 3. Following the guidelines outlined in this chapter, we
elect not to pick the viscosity. It is better to pick a fixed length (h) rather than a variable length (y); otherwise y would
appear in each Pi, which would not be desirable. We choose
V, ρ, and h
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = uV a1 ρ b1 h c1
mass:
{m } = {m }
time:
{t } = { t
length:
0
1 −1
−1 − a1
t
{L } = {L L L
1 a1
}
−3b1
Lc1
}
)( L t ) ( m L ) ( L )
1 −1
a1
1 −3
b1
1
c1
}
0 = b1
b1 = 0
0 = −1 − a1
a1 = −1
0 = 1 + a1 − 3b1 + c1
c1 = 0
b1
0
0
{( L t
The dependent Π is thus
Π1 =
Π 1:
u
V
The second Pi (the first independent Π in this problem) is generated:
{Π 2 } =
Π 2 = μV a2 ρ b2 h c2
mass:
{m } = {m m }
0
1
b2
{( m L t
1 −1 − 1
)( L t ) ( m L ) ( L )
1 −1
a2
1 −3
b2
1
c2
}
b2 = −1
0 = 1 + b2
7-40
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
{t } = { t
time:
length:
0
{L } = {L
−1 − a2
t
}
L L−3b2 Lc2
−1 a2
0
}
0 = −1 − a2
a2 = −1
0 = −1 + a2 − 3b2 + c2
c2 = −1
0 = −1 − 1 + 3 + c2
which yields
Π 2:
Π2 =
μ
ρVh
We recognize this Π as the inverse of the Reynolds number. So, after inverting,
Modified Π2:
Π2 =
ρVh
= Reynolds number = Re
μ
The third Pi (the second independent Π in this problem) is generated:
{Π 3 } =
Π 3 = yV a3 ρ b3 hc3
{( L )( L t
1
1 −1
) (m L ) (L )
a3
1 −3
b3
1
c3
}
mass:
{m } = { m }
0 = b3
b3 = 0
time:
{t } = {t }
0 = − a3
a3 = 0
0 = 1 + a3 − 3b3 + c3
c3 = −1
length:
0
b3
− a3
0
{L } = {L L
0
1 a3
L−3b3 Lc3
}
0 = 1 + c3
which yields
Π 3:
Π3 =
y
h
Step 6 We write the final functional relationship as
Relationship between Πs:
u
y⎞
⎛
= f ⎜ Re, ⎟
V
h
⎝
⎠
(2)
Discussion
We notice in the first and third Πs that when the parameter on which we are working has the same
dimensions as one of the repeating parameters, the Π is simply the ratio of those two parameters (here u/V and y/h).
7-41
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-57
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are seven parameters in this problem; n = 7,
u = f ( μ , V , h, ρ , y, t )
List of relevant parameters:
n=7
(1)
Step 2 The primary dimensions of each parameter are listed,
u
μ
V
h
ρ
y
t
{L t }
{m L t }
{L t }
{L }
{m L }
{L }
{t }
1 −1
1 −1 −1
1 −1
1 −3
1
1
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 7−3 = 4
Step 4 We need to choose three repeating parameters since j = 3. Following the guidelines outlined in this chapter, we do
not pick the viscosity. It is better to pick a fixed length (h) rather than a variable length (y); otherwise y would appear in
each Pi, which would not be desirable. It would also not be wise to have time appear in each parameter. We choose
V, ρ, and h
Repeating parameters:
Step 5 The Πs are generated. The first three Πs are identical to those of the previous problem, so we do not include
the details here. The fourth Π is formed by joining the new parameter t to the repeating variables,
{Π 4 } =
Π 4 = tV a4 ρ b4 h c4
{( t )( L t
1
1 −1
) (m L ) (L )
a4
1 −3
b4
1
c4
}
mass:
{m } = {m }
0 = b4
b4 = 0
time:
{t } = {t t }
0 = 1 − a4
a4 = 1
0 = a4 − 3b4 + c4
c4 = −1
length:
0
b4
1 − a4
0
{L } = {L L
0
a1
−3b4
Lc4
}
This Π is thus
Π4 =
Π 4:
tV
h
Step 6 Combining this result with the first three Πs from the previous problem,
Relationship between Πs:
Discussion
u
y tV ⎞
⎛
= f ⎜ Re, , ⎟
V
h
h ⎠
⎝
(2)
As t → ∞, Π4 becomes irrelevant and the result degenerates into that of the previous problem.
7-42
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-58
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are four parameters in this problem; n = 4,
(
c = f k , T , Rgas
List of relevant parameters:
)
n=4
(1)
Step 2 The primary dimensions of each parameter are listed; the ratio of specific heats k is dimensionless.
c
k
T
{L t }
{1}
{T }
1 −1
Rgas
{L t
2 −2
1
T −1
}
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (T, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−3 =1
Thus we expect only one Π.
Step 4 We need to choose three repeating parameters since j = 3. We only have one choice in this problem, since there are
only three independent parameters on the right-hand side of Eq. 1. However, one of these is already dimensionless, so it is a
Π all by itself. In this situation we reduce j by one and continue,
j = 3 −1 = 2
Reduction:
If this revised value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−2 = 2
We now expect two Πs. We choose two repeating parameters since j = 2,
T and Rgas
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = cT a1 Rgas b1
time:
{ t } = {t
temperature:
length:
}
{( L t
1 −1
)( T ) ( L t
1
a1
2 −2
T −1
)
b1
}
0 = −1 − 2b1
b1 = −1/ 2
{T } = {T }
a1 = b1
a1 = −1/ 2
{L } = {L L }
0 = 1 + 2b1
b1 = −1/ 2
0
0
0
−1− 2 b1
a1 − b1
1 2 b1
Fortunately the two results for exponent b1 agree. The dependent Π is thus
Π 1:
Π1 =
c
RgasT
7-43
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
The independent Π is already known,
Π 2:
Π2 = k
Step 6 We write the final functional relationship as
Relationship between Πs:
c
RgasT
= f (k )
(2)
Discussion
We cannot tell from dimensional analysis the exact form of the functional relationship. However, in this
case the result agrees with the known equation for speed of sound in an ideal gas, c = kRgasT .
7-44
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-59
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are five parameters in this problem; n = 5,
c = f ( k , T , Ru , M )
List of relevant parameters:
n=5
(1)
Step 2 The primary dimensions of each parameter are listed; the ratio of specific heats k is dimensionless.
c
k
T
{L t }
{1}
{T }
1 −1
Ru
{m L t
1 2 −2
1
M
T −1 N −1
}
{m N }
1
−1
Step 3 As a first guess, j is set equal to 5, the number of primary dimensions represented in the problem (m, T, L, N, and
t).
j =5
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−5 = 0
Obviously we cannot have zero Πs. We check that we have not missed a relevant parameter. Convinced that we have
included all the relevant parameters we reduce j by 1:
j = 5 −1 = 4
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−4 =1
Step 4 We need to choose four repeating parameters since j = 4. We only have one choice in this problem, since there are
only four independent parameters on the right-hand side of Eq. 1. However, one of these is already dimensionless, so it is a
Π all by itself. In this situation we reduce j by one (again) and continue,
j = 4 −1 = 3
Reduction:
If this revised value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
We now expect two Πs. Since j = 3 we choose three repeating parameters,
T, M, and Ru
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = cT a1 M b1 Ru c1
time:
{t } = {t
mass:
{m } = {m
0
0
−1 −2 c1
t
b1
}
m c1
}
{( L t
1 −1
)( T ) ( m n ) ( m L t
1
a1
1
−1
b1
0 = −1 − 2c1
0 = b1 + c1
b1 = −c1
1 2 −2
T −1 N −1
)
c1
}
c1 = −1/ 2
b1 = 1/ 2
7-45
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
amount of
matter:
temperature:
length:
{N } = {N
0
− b1
{T } = {T
0
a1
N − c1
T − c1
}
}
{L } = {L L }
0
1 2 c1
0 = −b1 − c1
b1 = −c1
b1 = 1/ 2
0 = a1 − c1
a1 = c1
a1 = −1/ 2
c1 = −1/ 2
0 = 1 + 2c1
Fortunately the two results for exponent b1 agree, and the two results for exponent c1 agree. (If they did not agree, we would
search for algebra mistakes. Finding none we would suspect that j is not correct or that we are missing a relevant parameter
in the problem.) The dependent Π is thus
Π 1:
Π1 =
c M
RuT
The independent Π is already known,
Π 2:
Π2 = k
Step 6 We write the final functional relationship as
Relationship between Πs:
Discussion
Π1 =
c M
RuT
= f (k )
(2)
Since we know that Rgas = Ru/M, we see that the result here is the same as that of the previous problem.
7-46
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-60
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are three parameters in this problem; n = 3,
(
c = f T , Rgas
List of relevant parameters:
)
n=3
(1)
Step 2 The primary dimensions of each parameter are listed,
c
T
{L t }
{T }
1 −1
Rgas
{L t
2 −2
1
T −1
}
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (T, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n − j = 3−3 = 0
Obviously this is not correct, so we re-examine our initial assumptions. We can add another variable, k (the ratio of specific
heats) to our List of relevant parameters. This problem would then be identical to Problem 7-58. Instead, for instructional
purposes we reduce j by one and continue,
j = 3 −1 = 2
Reduction:
If this revised value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n − j = 3− 2 =1
We now expect only one Π.
Step 4 We need to choose two repeating parameters since j = 2. We only have one choice in this problem, since there are
only two independent parameters on the right-hand side of Eq. 1,
Repeating parameters:
T and Rgas
Step 5 The dependent Π is generated:
{Π1} =
Π1 = cT a1 Rgas b1
time:
{ t } = {t
temperature:
length:
}
{( L t
1 −1
)( T ) ( L t
1
a1
2 −2
T −1
)
b1
}
0 = −1 − 2b1
b1 = −1/ 2
{T } = {T }
a1 = b1
a1 = −1/ 2
{L } = {L L }
0 = 1 + 2b1
b1 = −1/ 2
0
0
0
−1− 2 b1
a1 − b1
1 2 b1
Fortunately the two results for exponent b1 agree. The dependent Π is thus
7-47
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Π 1:
Π1 =
c
RgasT
Step 6 Since there is only one Π, it is a function of nothing. This is only possible if we set the Π equal to a constant. We
write the final functional relationship as
Relationship between Πs:
Π1 =
c
RgasT
= constant
(2)
Discussion
Our result represents an interesting case of “luck”. Although we failed to include the ratio of specific heats k
in our analysis, we nevertheless obtain the correct result. In fact, if we set the constant in Eq. 2 as the square root of k, our
result agrees with the known equation for speed of sound in an ideal gas, c = kRgasT .
7-48
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-61
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters, and
compare to the known equation for an ideal gas.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are three parameters in this problem; n = 3,
c = f ( P, ρ )
List of relevant parameters:
n=3
(1)
Step 2 The primary dimensions of each parameter are listed,
c
P
ρ
{L t }
{m L t }
{m L }
1 −1
1 −1 −2
1 −3
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n − j = 3−3 = 0
Obviously this is not correct, so we re-examine our initial assumptions. If we are convinced that c is a function of only P
and ρ, we reduce j by one and continue,
j = 3 −1 = 2
Reduction:
If this revised value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n − j = 3− 2 =1
We now expect only one Π.
Step 4 We need to choose two repeating parameters since j = 2. We only have one choice in this problem, since there are
only two independent parameters on the right-hand side of Eq. 1,
P and ρ
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = cP a1 ρ b1
time:
{t } = {t
mass:
{m } = {m
length:
0
−1 −2 a1
0
{L } = {L L
0
t
a1
}
mb1
1 −2 a1
}
L−3b1
}
{( L t
1 −1
)( m L
1 −1 −2
t
) (m L )
a1
1 −3
b1
}
0 = −1 − 2a1
a1 = −1/ 2
0 = a1 + b1
b1 = 1/ 2
0 = 1 − a1 − 3b1
0=0
0 = 1+ −
1
2
3
2
Fortunately the exponents for length agree with those of mass and time. The dependent Π is thus
7-49
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Π 1:
Π1 = c
ρ
P
Step 6 Since there is only one Π, it is a function of nothing. This is only possible if we set the Π equal to a constant. We
write the final functional relationship as
Relationship between Πs:
Π1 = c
ρ
P
= constant, or c = constant
P
ρ
(2)
The ideal gas equation is P = ρRgasT, or P/ρ = RgasT. Thus, Eq. 2 can be written as
Alternative result using ideal gas law:
c = constant RgasT
(3)
Equation 3 is indeed consistent with the equation c = kRgasT .
Discussion
There is no way to obtain the value of the constant in Eq. 2 or 3 solely by dimensional analysis, but it turns
out that the constant is the square root of k.
7-50
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-62
Solution
We are to use dimensional analysis to find a functional relationship between FD and variables V, L, and μ.
Assumptions 1 We assume Re << 1 so that the creeping flow approximation applies. 2 Gravitational effects are irrelevant.
3 No parameters other than those listed in the problem statement are relevant to the problem.
We follow the step-by-step method of repeating variables.
Analysis
Step 1 There are four variables and constants in this problem; n = 4. They are listed in functional form, with the
dependent variable listed as a function of the independent variables and constants:
FD = f (V , L, μ )
List of relevant parameters:
n=4
Step 2 The primary dimensions of each parameter are listed.
FD
V
L
μ
{m L t }
{L t }
{L }
{m L t }
1 1 −2
1 −1
1 −1 −1
1
Step 3 As a first guess, we set j equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the number of Πs expected is
Number of expected Πs:
k = n− j = 4−3 =1
Step 4 Now we need to choose three repeating parameters since j = 3. Since we cannot choose the dependent variable, our
only choices are V, L, and μ.
Step 5 Now we combine these repeating parameters into a product with the dependent variable FD to create the
dependent Π,
Π1 = FDV a1 Lb1 μ c1
Dependent Π:
(1)
We apply the primary dimensions of Step 2 into Eq. 1 and force the Π to be dimensionless,
Dimensions of Π1:
{Π1} = {m0 L0 t 0 } = {FDV a Lb μ c } =
1
1
1
{( m L t
1 1 −2
)( L t ) ( L ) ( m L
1 −1
a1
1
b1
1 −1 −1
t
)
c1
}
Now we equate the exponents of each primary dimension to solve for exponents a1 through c1.
mass:
time:
length:
{m } = {m m }
0
1
{ t } = {t
0
c1
−2 − a1 − c1
t
t
}
{L } = {L L L L }
0
1 a1
b1
− c1
0 = 1 + c1
c1 = −1
0 = −2 − a1 − c1
a1 = −1
0 = 1 + a1 + b1 − c1
b1 = −1
Equation 1 thus becomes
Π 1:
Π1 =
FD
μVL
(2)
Step 6 We now write the functional relationship between the nondimensional parameters. In the case at hand, there is
only one Π, which is a function of nothing. This is possible only if the Π is constant. Putting Eq. 2 into standard functional
form,
7-51
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Relationship between Πs:
Π1 =
FD
= f ( nothing ) = constant
μVL
(3)
FD = constant ⋅ μVL
(4)
or
Result of dimensional analysis:
Thus we have shown that for creeping flow around an object, the aerodynamic drag force is simply a constant multiplied by
μVL, regardless of the shape of the object.
Discussion
This result is very significant because all that is left to do is find the constant, which will be a function of
the shape of the object (and its orientation with respect to the flow).
7-52
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-63
Solution
We are to find the functional relationship between the given parameters and name any established
dimensionless parameters.
Assumptions
1 The given parameters are the only ones relevant to the flow at hand.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are five parameters in this problem; n = 5,
( (
)
V = f d p , ρp − ρ , μ, g
List of relevant parameters:
)
n=5
(1)
Step 2 The primary dimensions of each parameter are listed,
V
dp
{L t }
{L }
1 −1
( ρ p - ρ)
μ
g
{m L } {m L t } {L t }
1 −3
1
1 −1 −1
1 −2
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. We pick length scale dp, density difference (ρp - ρ), and
gravitational constant g.
(
)
d p , ρ p -ρ , and g
Repeating parameters:
Step 5 The Πs are generated. Note that for the first Π we do the algebra in our heads since the relationship is very
simple. The dependent Π is
Π1 = a Froude number:
Π1 =
V
gd p
This Π is a type of Froude number. Similarly, the Π formed with viscosity is generated,
(
Π2 = μ d pa ρ p − ρ
)
b
{Π 2 } =
gc
mass:
{m } = { m m }
time:
{t } = { t
length:
0
1
0
{L } = { L
0
t
−1 a
}
L L−3b Lc
1 −1 −1
)( L ) ( m L ) ( L t ) }
1
a
1 −3
0 = −1 − 2c
}
0 = −1 + a − 3b + c
0 = −1 + a + 3 −
b
1 −2
c
b = −1
0 = 1+ b
b
−1 − 2 c
{( m L t
1
2
c=−
1
2
a=−
3
2
which yields
7-53
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Π 2:
μ
Π2 =
(ρ
p
)
3
− ρ dp2 g
We recognize this Π as the inverse of a kind of Reynolds number if we split the dp terms to separate them into a length
scale and (when combined with g) a velocity scale. The final form is
Modified Π2 = a Reynolds number:
Π2 =
(ρ
p
)
− ρ d p gd p
μ
Step 6 We write the final functional relationship as
Relationship between Πs:
(
)
⎛ ρ p − ρ d p gd p ⎞
⎟
= f⎜
⎜
⎟
μ
gd p
⎝
⎠
V
(2)
Discussion
We cannot determine the form of the relationship by purely dimensional reasoning since there are two Πs.
However, in Chap. 10 we shall see that Π1 is a constant times Π2.
7-54
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-64
Solution
conditions.
We are to develop an equation for the settling speed of an aerosol particle falling in air under creeping flow
Assumptions 1 The particle falls at steady speed V. 2 The Reynolds number is small enough that the creeping flow
approximation is valid.
Analysis
We start by recognizing that as the particle falls at steady settling speed, its net weight W must equal the
aerodynamic drag FD on the particle. We also know that W is proportional to (ρp - ρ)gdp3. Thus,
Equating forces:
(
)
W = constant1 ρ p − ρ gd p 3 = FD = constant 2 μVd p
(1)
where we have converted the notation of the previous problem, and we have defined two different constants. The two
constants in Eq. 1 can be combined into one new constant for simplicity. Solving for V,
Settling speed:
If we divide both sides of Eq. 2 by
(ρ
V = constant
p
)
− ρ gd p 2
μ
(2)
gd p we see that the functional relationship given by Eq. 2 of the previous problem is
consistent.
Discussion
This result is valid only if the Reynolds number is much smaller than one, as will be discussed in Chap. 10.
If the particle is less dense than the fluid (e.g. bubbles rising in water), our result is still valid, but the particle rises instead
of falls.
7-65
Solution
We are to determine how the settling speed of an aerosol particle falling in air under creeping flow
conditions changes when certain parameters are doubled.
Assumptions 1 The particle falls at steady speed V. 2 The Reynolds number is small enough that the creeping flow
approximation is valid.
Analysis
From the results of the previous problem, we see that if particle size doubles, the settling speed increases
by a factor of 22 = 4. Similarly, if density difference doubles, the settling speed increases by a factor of 21 = 2.
Discussion
This result is valid only if the Reynolds number remains much smaller than unity, as will be discussed in
Chap. 10. As the particle’s settling speed increases by a factor of 2 or 4, the Reynolds number will also increase by that
same factor. If the new Reynolds number is not small enough, the creeping flow approximation will be invalid and our
results will not be correct, although the error will probably be small.
7-55
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-66
Solution
We are to generate a nondimensional relationship between the given parameters.
Assumptions
problem.
1 The flow is fully developed. 2 The fluid is incompressible. 3 No other parameters are significant in the
Analysis
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters.
Step 1 All the relevant parameters in the problem are listed in functional form:
ΔP = f (V , ε , ρ , μ , D, L )
List of relevant parameters:
n=7
Step 2 The primary dimensions of each parameter are listed:
ΔP
ε
ρ
μ
D
L
{L }
{m L }
{m L t }
{L }
{L }
V
{m L t } {L t }
1 −1 −2
1 −1
1 −3
1
1 −1 −1
1
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 7−3 = 4
Step 4 We need to choose three repeating parameters since j = 3. Following the guidelines listed in Table 7-3, we cannot
pick the dependent variable, ΔP. We cannot choose any two of parameters ε, L, and D since their dimensions are
identical. It is not desirable to have μ or ε appear in all the Πs. The best choice of repeating parameters is thus V, D, and ρ.
V, D, and ρ
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = ΔPV a1 D b1 ρ c1
mass:
{m } = {m m }
time:
{t } = { t
length:
0
1
0
{L } = {L
0
}
)( L t ) ( L ) ( m L )
1 −1
a1
1
b1
1 −3
c1
}
c1 = −1
0 = −2 − a1
a1 = −2
0 = −1 + a1 + b1 − 3c1
b1 = 0
}
L Lb1 L−3c1
−1 a1
1 −1 −2
0 = 1 + c1
c1
−2 − a1
t
{( m L t
0 = −1 − 2 + b1 + 3
The dependent Π is thus
Π 1:
Π1 =
ΔP
ρV 2
From Table 7-5, the established nondimensional parameter most similar to our Π1 is the Euler number Eu. No
manipulation is required.
We form the second Π with μ. By now we know that we will generate a Reynolds number,
Π 2 = μV a2 D b2 ρ c2
Π2 =
ρVD
= Reynolds number = Re
μ
7-56
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
The final two Π groups are formed with ε and then with L. The algebra is trivial for these cases since their dimension
(length) is identical to that of one of the repeating variables (D). The results are
Π 3 = εV a3 D b3 ρ c3
Π 4 = LV a4 D b4 ρ c4
Π3 =
Π4 =
ε
D
= Roughness ratio
L
= Length-to-diameter ratio or aspect ratio
D
Step 6 We write the final functional relationship as
Relationship between Πs:
Eu =
ΔP
ε L⎞
⎛
= f ⎜ Re, , ⎟
2
D D⎠
ρV
⎝
(1)
Discussion
The result applies to both laminar and turbulent fully developed pipe flow; it turns out, however, that the
second independent Π (roughness ratio) is not nearly as important in laminar pipe flow as in turbulent pipe flow. Since ΔP
drops linearly with distance down the pipe, we know that ΔP is linearly proportional to L/D. It is not possible to determine
the functional relationships between the other Πs by dimensional reasoning alone.
7-57
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-67
Solution
We are to determine by what factor volume flow rate increases in the case of fully developed laminar pipe
flow when pipe diameter is doubled.
Assumptions 1 The flow is steady. 2 The flow is fully developed, meaning that dP/dx is constant and the velocity profile
does not change downstream.
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters.
Analysis
Step 1 All the relevant parameters in the problem are listed in functional form:
dP ⎞
⎛
V = f ⎜ D, μ ,
dx ⎟⎠
⎝
List of relevant parameters:
n=4
Step 2 The primary dimensions of each parameter are listed:
V
D
{L t }
{L }
3 −1
μ
dP/dx
{m L t } {m L
1 −1 −1
1
1 −2 −2
t
}
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−3 =1
Step 4 We need to choose three repeating parameters since j = 3. Here we must pick all three independent parameters,
D, μ, and dP/dx
Repeating parameters:
Step 5 The Π is generated:
{Π1} =
a
Π1 = V ( dP / dx ) 1 D b1 μ c1
mass:
time:
{m } = {m
0
{t } = {t
0
length:
a1
}
−1 −2 a1 − c1
t
{L } = {L L
0
m c1
3 −2 a1
t
}
Lb1 L− c1
}
{( L t
3 −1
)( m L
1 −2 −2
t
) (L ) (m L
a1
1
b1
1 −1 −1
t
)
c1
}
0 = a1 + c1
c1 = −a1
0 = −1 − 2a1 − c1
a1 = −1
0 = −1 − 2a1 + a1
c1 = 1
0 = 3 − 2a1 + b1 − c1
b1 = −4
b1 = −3 + 2a1 + c1
The dependent Π is thus
Π 1:
Π1 =
V μ
dP
D4
dx
Step 6 Since there is only one Π, we set it equal to a constant. We write the final functional relationship as
7-58
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Relationship between Πs:
Π1 = constant,
D 4 dP
V = constant
μ dx
(1)
We see immediately that if the pipe diameter is doubled with all other parameters fixed, the volume flow rate will
increase by a factor of 24 = 16.
Discussion
We will see in Chap. 9 that the constant is π/8. There is no way to obtain the value of the constant from
dimensional analysis alone.
7-59
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-68
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are four parameters in this problem; n = 4,
(
Q = f m , c p , (Tout − Tin )
List of relevant parameters:
)
n=4
(1)
Step 2 The primary dimensions of each parameter are listed,
Q
m
{m L t }
{m t }
1 2 −3
Tout- Tin
cp
{L t
1 −1
2 −2
T −1
{T }
}
1
Step 3 As a first guess, j is set equal to 4, the number of primary dimensions represented in the problem (m, T, L, and t).
j=4
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−4 = 0
Obviously this is not correct, so we re-examine our initial assumptions. We are convinced that our list of parameters is
sufficient, so we reduce j by one and continue,
j = 4 −1 = 3
Reduction:
If this revised value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−3 =1
We now expect only one Π.
Step 4 We need to choose three repeating parameters since j = 3. We only have one choice in this problem, since there are
only three independent parameters on the right-hand side of Eq. 1,
m , c p , and (Tout − Tin )
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
a1 c b1 (T − T )c1
Π1 = Qm
out
in
p
{( m L t
1 2 −3
)( m t ) ( L t
1 −1
a1
2 −2
T −1
) (T )
b1
1
c1
}
mass:
{m } = {m }
0 = 1 + a1
a1 = −1
length:
{L } = {L L }
0 = 2 + 2b1
b1 = −1
temperature:
{T } = {T
}
c1 = b1
c1 = −1
time:
{t } = {t
}
0 = −3 − a1 − 2b1
3 = 1+ 2
1+ a1
0
0
0
0
2
2 b1
− b1 + c1
−3 − a1 − 2 b1
Fortunately the result for the time exponents is consistent with that of the other dimensions. The dependent Π is thus
7-60
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Π 1:
Π1 =
Q
p (Tout − Tin )
mc
Step 6 Since there is only one Π, it is a function of nothing. This is only possible if we set the Π equal to a constant. We
write the final functional relationship as
Relationship between Πs:
Π1 =
Q
= constant
p (Tout − Tin )
mc
(2)
Discussion
When there is only one Π, we know the functional relationship to within some (unknown) constant. In this
p (Tout − Tin ) . There is no way
particular case, comparing to Eq. 1 of Problem 7-24, we see that the constant is unity, Q = mc
to obtain the constant in Eq. 2 from dimensional analysis; however, one experiment would be sufficient to determine the
constant.
Experimental Testing and Incomplete Similarity
7-69C
Solution
We are to define wind tunnel blockage and discuss its acceptable limit. We are also to discuss the source of
measurement errors at high values of blockage.
Analysis
Wind tunnel blockage is defined as the ratio of model frontal area to cross-sectional area of the testsection. The rule of thumb is that the blockage should be no more than 7.5%. If the blockage were significantly higher than
this value, the flow would have to accelerate around the model much more than if the model were in an unbounded
situation. Hence, similarity would not be achieved. We might expect the aerodynamic drag on the model to be too high
since the effective freestream speed is too large due to the blockage.
Discussion
increases.
7-70C
Solution
There are formulas to correct for wind tunnel blockage, but they become less and less reliable as blockage
We are to discuss the rule of thumb concerning Mach number and incompressibility.
Analysis
The rule of thumb is that the Mach number must stay below about 0.3 in order for the flow field to be
considered “incompressible”. What this really means is that compressibility effects, although present at all Mach
numbers, are negligibly small compared to other effects driving the flow. If Ma is larger than about 0.3 in a wind tunnel
test, the model flow field loses both kinematic and dynamic similarity, and the measured results are questionable. Of
course, the error increases as Ma increases.
Discussion
Compressible flow is discussed in detail in Chap. 12. There you will see where the value 0.3 comes from.
7-61
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-71C
Solution
We are to discuss some situations in which a model should be larger than its prototype.
Analysis
There are many possible situations, and students’ examples should vary. Generally, any flow field that is
very small and/or very fast benefits from simulation with a larger model. In most cases these are situations in which we
want the model to be larger and slower so that experimental measurements and flow visualization are easier. Here are a few
examples:
−
−
−
−
−
−
Modeling a hard disk drive.
Modeling insect flight.
Modeling the settling of very small particles in air or water.
Modeling the motion of water droplets in clouds.
Modeling flow through very fine tubing.
Modeling biological systems like blood flow through capillaries, flow in the bronchi of lungs, etc.
Discussion
You can think of several more examples.
7-72C
Solution
We are to discuss the purpose of a moving ground belt
and suggest an alternative.
Analysis
From the frame of reference of a moving car, both the air
and the ground approach the car at freestream speed. When we test a
model car in a wind tunnel, the air approaches at freestream speed, but
the ground (floor of the wind tunnel) is stationary. Therefore we are not
modeling the same flow. A boundary layer builds up on the wind tunnel
floor, and the flow under the car cannot be expected to be the same as
that under a real car. A moving ground belt solves this problem. Another
way to say the same thing is to say that without the moving ground belt,
there would not be kinematic similarity between the underside of the
model and the underside of the prototype.
If a moving ground belt is unavailable, we could instead install
a false wall – i.e., a thin flat plate just above the boundary layer on
the floor of the wind tunnel. A sketch is shown in Fig. 1. At least then
the boundary layer will be very thin and will not have as much influence
on the flow under the model.
Discussion
V
Wind tunnel
test section
False wall
FIGURE 1
A false wall along the floor of a wind tunnel
to reduce the size of the ground boundary
layer.
We discuss boundary layer growth in Chap. 10.
7-62
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-73
Solution
We are to show that Froude number and Reynolds number are the dimensionless parameters that appear in a
problem involving shallow water waves.
Assumptions
viscosity μ.
1 Wave speed c is a function only of depth h, gravitational acceleration g, fluid density ρ, and fluid
Analysis
We perform a dimensional analysis using the method of repeating variables.
Step 1 There are five parameters in this problem; n = 5,
c = f ( h, ρ , μ , g )
List of relevant parameters:
n=5
Step 2 The primary dimensions of each parameter are listed,
c
h
{L t }
{L }
1 −1
ρ
μ
g
{ m L } {m L t } {L t }
1 −3
1
1 −1 −1
1 −2
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. We pick length scale h, density difference ρ, and
gravitational constant g.
h, ρ , and g
Repeating parameters:
Step 5 The Πs are generated. Note that for the first Π we do the algebra in our heads since the relationship is very
simple. The dependent Π is
Π1 = Froude number:
c
Π1 = Fr =
(1)
gh
This Π is the Froude number. Similarly, the Π formed with viscosity is generated,
{Π 2 } =
Π 2 = μ ha ρ b g c
mass:
{m } = { m m }
time:
{t } = { t
length:
0
1
0
{L } = { L
0
t
−1 a
}
L L−3b Lc
1 −1 −1
)( L ) ( m L ) ( L t ) }
a
1
b
1 −3
0 = −1 − 2c
}
1 −2
c
b = −1
0 = 1+ b
b
−1 − 2 c
{( m L t
0 = −1 + a − 3b + c
0 = −1 + a + 3 −
1
2
c=−
1
2
a=−
3
2
which yields
Π 2:
μ
Π2 =
3
ρh2 g
7-63
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
We can manipulate this Π into the Reynolds number if we invert it and then multiply by Fr (Eq. 1) The final form is
Modified Π2 = Reynolds number:
Π 2 = Re =
ρ ch
μ
Step 6 We write the final functional relationship as
Fr =
Relationship between Πs:
Discussion
c
gh
= f ( Re ) where Re =
ρ ch
μ
As discussed in this chapter, it is often difficult to match both Fr and Re between a model and a prototype.
7-74
Solution
We are to nondimensionalize experimental pipe data, plot
the data, and determine if Reynolds number independence has been
achieved. We are then to extrapolate to a higher speed.
Assumptions 1 The flow is fully developed. 2 The flow is steady and
incompressible.
Properties
For water at T = 20 C and atmospheric pressure, ρ =
998.0 kg/m3 and μ = 1.002 × 10-3 kg/m⋅s.
o
Analysis
(a) We convert each data point in the table from V and ΔP
to Reynolds number and Euler number. The calculations at the last
(highest speed) data point are shown here:
Reynolds number:
ρVD ( 998.0 kg/m ) ( 50 m/s )( 0.104 m )
=
= 5.18 × 10
Re =
μ
1.002 × 10
6
0.307
Reynolds number
independence
Eu 0.306
0.305
0.304
0
(1)
kg/m ⋅ s
2
Re × 10-6
4
6
FIGURE 1
Nondimensionalized experimental data from
a section of pipe.
and
Euler number:
758, 700 N/m 2
ΔP
⎛ kg m ⎞
Eu =
=
⎟ = 0.304
2
2 ⎜
2
3
ρV
998.0 kg/m ( 50 m/s ) ⎝ s N ⎠
(
0.308
0.303
3
−3
0.309
(2)
)
We plot Eu versus Re in Fig. 1. Although there is experimental scatter in the data, it appears that Reynolds number
independence has been achieved beyond a Reynolds number of about 2 × 106. The average value of Eu based on the last 6
data points is 0.3042.
(b) We extrapolate to higher speeds. At V = 80 m/s, we calculate ΔP, assuming that Eu remains constant to higher values of
Re,
Extrapolated value:
2
2⎛ s N ⎞
2
ΔP = Eu × ρV 2 = 0.3042 998.0 kg/m3 ( 80 m/s ) ⎜
⎟ = 1, 940, 000 N/m
kg
m
⎝
⎠
(
)
(3)
Discussion
It is shown in Chap. 8 that Reynolds number independence is indeed achieved at high-enough values of Re.
The threshold value above which Re independence is achieved is a function of relative roughness height, ε/D.
7-64
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-75
Solution
We are to calculate the wind tunnel blockage of a model truck in a wind tunnel and determine if it is within
acceptable limits.
Assumptions 1 The frontal area is equal to truck width times height. (Note that the actual area of the truck may be
somewhat smaller than this due to rounded corners and the air gap under the truck, but a truck looks nearly like a rectangle
from the front, so this is not a bad approximation.)
Analysis
Blockage:
Wind tunnel blockage is defined as the ratio of model frontal area to cross-sectional area of the test-section,
Blockage =
Amodel
Awind tunnel
=
( 0.159 m )( 0.257 m )
= 0.034 = 3.4%
(1.2 m )(1.0 m )
(1)
The rule of thumb is that the blockage should be no more than 7.5%. Since we are well below this value, we need not worry
about blockage effects.
Discussion
model.
The length of the model does not enter our analysis since we are only concerned with the frontal area of the
7-76C
Solution
We are to discuss whether Reynolds number independence has been achieved, and whether the researchers
can be confident about it.
Analysis
We remove the last four data points from Table 7-7 and from Fig. 7-41. From the remaining data it appears
that the drag coefficient is beginning to level off, but is still decreasing with Re. Thus, the researchers do not know if
they have achieved Reynolds number independence or not.
Discussion
The wind tunnel speed is too low to achieve Reynolds number independence.
7-65
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-77E
Solution
We are to calculate the size and scale of the model truck to be constructed, and calculate its maximum
Reynolds number. Then we are to determine whether this model in this wind tunnel will achieve Reynolds number
independence.
Assumptions 1 The model will be constructed carefully so as to achieve approximate geometric similarity. 2 The wind
tunnel air is at the same temperature and pressure as that flowing over the prototype truck.
Properties
For air at T = 80oF and atmospheric pressure, ρ = 0.07350 lbm/ft3 and μ = 1.248 × 10-5 lbm/ft⋅s.
Analysis
(a) The rule of thumb about blockage is that we should keep the blockage below 7.5%. Thus, the frontal
area of the model truck must be no more than 0.075 × Awind tunnel. The ratio of height to width of the full-scale truck is Hp/Wp
= 12/8.33 = 1.44. Thus, for the geometrically similar model truck,
Wm =
Equation for model truck width:
Am 7.5% Awind tunnel
=
1.44Wm
Hm
(1)
We solve Eq. 1 for Wm,
Model truck width:
Wm =
) = 4.56 in
(2)
Wm = 4.56 in, H m = 6.57 in, Lm = 28.5 in
(3)
7.5% Awind tunnel
=
1.44
(
0.075 400 in 2
1.44
Scaling the height and length geometrically,
Model truck dimensions:
These dimensions represent a model that is scaled at approximately 1:22.
(b) At the maximum speed, with Re based on truck width,
Maximum Re:
ρWmVmax ( 0.07350 lbm/ft ) ( 4.56 in )(160 ft/s ) ⎛ 1 ft ⎞
5
=
⎜ 12 in ⎟ = 3.58×10
1.248 × 10−5 lbm/ft ⋅ s
μ
⎝
⎠
3
Re =
(4)
(c) Based on the data of Fig. 7-41, this Reynolds number is shy of the value needed to achieve Reynolds number
independence.
Discussion
The students should run at the highest wind tunnel speed. Their measured values of CD will probably be
higher than those of the prototype, but the relative difference in CD due to their modifications should still be valid.
7-66
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-78
Solution
We are to calculate and plot CD as a function of Re for a given set of wind tunnel measurements, and
determine if dynamic similarity and/or Reynolds number independence have been achieved. Finally, we are to estimate the
aerodynamic drag force acting on the prototype car.
Assumptions 1 The model car is geometrically similar to the prototype car. 2 The aerodynamic drag on the strut holding
the model car is negligible.
Properties
For air at atmospheric pressure and at T = 25oC, ρ =
3
1.184 kg/m and μ = 1.849 × 10-5 kg/(m s).
0.6
Analysis
We calculate CD and Re for the last data point listed in
the given table (at the fastest wind tunnel speed),
Model drag coefficient at last data point:
F
CD ,m = 1 D ,m2
2 ρ mVm Am
0.5
CD 0.45
⎛ kg m ⎞
s 2 N ⎟⎠
4.91 N
=
1
2
(1.184 kg/m ) (55 m/s )
3
0.55
⎜
2 (1.69 m )(1.30 m ) ⎝
0.4
162
0.35
= 0.319
0.3
and
0
Model Reynolds number at last data point:
ρ VW
Re m = m m m
μm
(1.184 kg/m ) ( 55 m/s ) ⎛⎜⎝ 1.69
16
3
=
⎞
m⎟
⎠
(1)
1.849 × 10−5 kg/m ⋅ s
1
2
Re × 10-5
3
4
FIGURE 1
Aerodynamic drag coefficient as a function
of Reynolds number – results
nondimensionalized from wind tunnel test
data on a model car.
= 3.72 ×105
We repeat the above calculations for all the data points in the given table, and we plot CD verses Re in Fig. 1.
Have we achieved dynamic similarity? Well, we have geometric similarity between model and prototype, but the
Reynolds number of the prototype car is
3
ρ pVpWp (1.184 kg/m ) ( 29 m/s )(1.69 m )
Reynolds number of prototype car: Rep =
=
= 3.14 × 106
μp
1.849 × 10−5 kg/m ⋅ s
(2)
where the width and speed of the prototype are used in the calculation of Rep. Comparison of Eqs. 1 and 2 reveals that the
prototype Reynolds number is more than eight times larger than that of the model. Since we cannot match the independent
Πs in the problem, dynamic similarity has not been achieved.
Have we achieved Reynolds number independence? From Fig. 1 we see that Reynolds number independence
has indeed been achieved – at Re greater than about 3 × 105, CD has leveled off to a value of about 0.32 (to two significant
digits).
Since we have achieved Reynolds number independence, we can extrapolate to the full scale prototype, assuming
that CD remains constant as Re is increased to that of the full scale prototype.
Aerodynamic drag on the prototype:
⎛ s2 N ⎞
1
1
2
FD ,p = ρ pVp 2 Ap CD ,p = 1.184 kg/m 3 ( 29 m/s ) (1.69 m )(1.30 m ) 0.32 ⎜
⎟ = 350 N
2
2
⎝ kg m ⎠
(
Discussion
)
We give our final result to two significant digits.
7-67
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Review Problems
7-79C
Solution
(a) False: Kinematic similarity is a necessary but not sufficient condition for dynamic similarity.
(b) True: You cannot have dynamic similarity if the model and prototype are not geometrically similar.
(c) True: You cannot have kinematic similarity if the model and prototype are not geometrically similar.
(d) False: It is possible to have kinematic similarity (scaled velocities at corresponding points), yet not have dynamic
similarity (forces do not scale at corresponding points).
7-80C
Solution
We are to think of and describe a prototype and model flow in which there is geometric but not kinematic
similarity even though Rem = Rep.
Students’ responses will vary. Here are some examples:
Analysis
−
−
−
A model car is being tested in a wind tunnel such that there is geometric similarity and the wind tunnel speed is
adjusted so that Rem = Rep. However, there is not a moving ground belt, so there is not kinematic similarity
between the model and prototype.
A model airplane is being tested in a wind tunnel such that there is geometric similarity and the wind tunnel speed
is adjusted so that Rem = Rep. However, the Mach numbers are quite different, and therefore kinematic similarity is
not achieved.
A model of a river or waterfall or other open surface flow problem in which there is geometric similarity and the
speed is adjusted so that Rem = Rep. However, the Froude numbers do not match and therefore the velocity fields
are not similar and kinematic similarity is not achieved.
Discussion
There are many more acceptable cases that students may imagine.
7-81C
Solution
We are to find at least three established nondimensional parameters not listed in Table 7-5, and list these
following the format of that table.
Analysis
Students’ responses will vary. Here are some examples:
Name
Definition
Bingham
number
Bm =
Elasticity
number
El =
Galileo number
Ga =
Ratio of significance
τL
μV
yield stress
viscous stress
tc μ
ρ L2
elastic force
inertial force
gD 3 ρ 2
gravitational force
viscous force
μ
2
In the above, tc is a characteristic time.
Discussion
There are many more established dimensionless parameters in the literature. Some sneaky students may
make up their own!
7-68
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-82
Solution
We are to determine the primary dimensions of each variable, and then show that Hooke’s law is
dimensionally homogeneous.
Analysis
(a) Moment of inertia has dimensions of length4,
Primary dimensions of moment of inertia:
{I } = {length 4 } = {L4 }
(1)
(b) Modulus of elasticity has the same dimensions as pressure,
Primary dimensions of modulus of elasticity:
force ⎫ ⎧ mass × length
1 ⎫ ⎧ m ⎫
×
{E} = ⎧⎨
⎬=⎨
⎬=⎨
⎬
2
time
length 2 ⎭ ⎩ Lt 2 ⎭
⎩ area ⎭ ⎩
(2)
Or, in exponent form, {E} = {m1 L-1 t-2}.
(c) Strain is defined as change in length per unit length, so it is dimensionless.
⎧ length ⎫
⎬ = {1}
⎩ length ⎭
{ε } = ⎨
Primary dimensions of strain:
(3)
(d) Stress is force per unit area, again just like pressure.
Primary dimensions of stress:
force ⎫ ⎧ mass × length ⎫ ⎧ m ⎫
=⎨ 2⎬
⎬=⎨
2
2 ⎬
⎩ area ⎭ ⎩ time × length ⎭ ⎩ Lt ⎭
{σ } = ⎧⎨
(4)
Or, in exponent form, {σ} = {m1 L-1 t-2}.
(e) Hooke’s law is σ = Eε. We write the primary dimensions of both sides:
⎧ m ⎫
⎧ m
⎫ ⎧ m ⎫
Primary dimensions of Hooke’s law: {σ } = ⎨ 2 ⎬ = { Eε } = ⎨ 2 × 1⎬ = ⎨ 2 ⎬
⎩ Lt ⎭
⎩ Lt
⎭ ⎩ Lt ⎭
(5)
Or, in exponent form, the dimensions of both sides of the equation are {m1 L-1 t-2}. Thus we see that Hooke’s law is indeed
dimensionally homogeneous.
Discussion
somewhere.
If the dimensions of Eq. 5 were not homogeneous, we would surely expect that we made an error
7-69
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-83
Solution
We are to find the functional relationship between the given parameters and name any established
dimensionless parameters.
Assumptions
1 The given parameters are the only ones relevant to the flow at hand.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are five parameters in this problem; n = 5,
z d = f ( F , L, E , I )
List of relevant parameters:
n=5
(1)
Step 2 The primary dimensions of each parameter are listed,
zd
F
L
E
I
{L }
{m L t }
{L }
{m L t }
{L }
1
1 1 −2
1 −1 −2
1
4
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. We cannot pick both length L and moment of inertia I
since their dimensions differ only by a power. We also notice that we cannot choose F, L, and E since these three
parameters can form a Π all by themselves. So, we set j = 3 – 1 = 2, and we choose two repeating parameters, expecting
5 – 2 = 3 Πs,
Repeating parameters:
L and E
Step 5 The Πs are generated. Note that for the first Π we do the algebra in our heads since zd has the same
dimensions as L. The dependent Π is
Π 1:
Π1 =
zd
L
This Π is not an established dimensionless group, although it is a ratio of two lengths, similar to an aspect ratio.
We form the second Π with force F:
{Π 2 } =
Π 2 = FLa E b
mass:
{m } = { m m }
time:
{t } = {t
length:
{L } = { L L L }
0
0
0
1
b
−2 −2 b
t
1 a
}
−b
{( m L t
1 1 −2
)( L ) ( m L
1
a
1 −1 −2
t
)}
b
0 = 1+ b
b = −1
0 = −2 − 2b
b = −1
0 = 1+ a − b
a = −1 + b
a = −2
which yields
7-70
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Π 2:
Π2 =
F
L2 E
We do not recognize Π2 as a named dimensionless parameter.
The final Π is formed with moment of inertia. Since {I} = {L4}, there is no need to go through the algebra – we
write
Π 3:
Π3 =
I
L4
Again, we do not recognize Π2 as a named dimensionless parameter.
Step 6 We write the final functional relationship as
Relationship between Πs:
Discussion
zd
⎛ F I ⎞
= f⎜ 2 , 4⎟
L
⎝LE L ⎠
(2)
We cannot determine the form of the relationship by purely dimensional reasoning since there are three Πs.
7-71
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-84
Solution
We are to generate dimensionless relationships among given parameters, and then we are to discuss how ΔP
decreases if the time is doubled.
1 The given parameters are the only relevant ones in the problem.
Assumptions
(a) We perform dimensional analyses using the method of repeating variables. First we analyze ΔP:
Analysis
Step 1 There are four parameters in this problem; n = 4,
ΔP = f ( t , c, E )
List of relevant parameters:
n=4
(1)
Step 2 The primary dimensions of each parameter are listed,
ΔP
t
c
E
{m L t }
{t }
{L t }
{m L t }
1 −1 −2
1 −1
1
1 2 −2
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−3 =1
Step 4 We need to choose three repeating parameters since j = 3. We pick all the independent parameters – time t, speed
of sound c, and energy E,
Repeating parameters:
t , c, and E
Step 5 The dependent Π is generated:
{Π1} =
Π1 = ΔP × t a1 cb1 E c1
mass:
length:
time:
{m } = { m m }
0
1
{L } = {L
0
{t } = {t
0
c1
−1 b1
L L2 c1
}
−2 a1 − b1 −2 c1
t t t
{( m L t
1 −1 −2
)( t ) ( L t ) ( m L t )
1
a1
1 −1
b1
1 2 −2
c1
}
0 = 1 + c1
c1 = −1
0 = −1 + b1 + 2c1
b1 = 3
b1 = 1 − 2c1
}
a1 = 3
0 = −2 + a1 − b1 − 2c1
a1 = 2 + b1 + 2c1
The dependent Π is thus
Π1 for ΔP:
Π1 =
t 3 c 3 ΔP
E
This Π is not an established one, so we leave it as is.
Step 6 We write the final functional relationship as
Relationship between Πs:
ΔP = constant
E
t 3c3
(2)
7-72
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
We perform a similar dimensional analysis using the same repeating variables, but this time for radius r. We do
not show the algebra since the Π can be found by inspection. We get
Π1 =
Π1 for r:
r
ct
Since this is the only Π, it must be equal to a constant,
Relationship between Πs:
r = constant ⋅ ct
(3)
(b) From Eq. 2 we see that if t is doubled, ΔP decreases by a factor of 23 = 8.
Discussion
The pressure rise across the blast wave decays rapidly with time (and with distance from the explosion).
The speed of sound depends on temperature. If the explosion is of sufficient strength, T will increase significantly and c
will not remain constant.
7-85
Solution
We are to find an alternate definition of Archimedes number, and list it following the format of Table 7-5.
Then we are to find an established Π group that is similar.
Analysis
Students’ responses will vary. There seems to be a plethora of definitions of Archimedes number. Here is
the one most appropriate for buoyant fluids:
Name
Definition
Archimedes
number
Ar =
gLΔρ
ρV 2
Ratio of significance
buoyant force
inertial force
In the above, Δρ is a characteristic density difference in the fluid (due to buoyancy) and ρ is a characteristic or average
density of the fluid. A glance through Table 7-5 shows that the Richardson number is very similar to this alternative
definition of Ar. In fact, the alternate form of Ri (Problem 7-55) is identical to our new Ar.
Discussion
Some students may find other definitions that are also valid. For example, Δρ/ρ may be replaced by ΔT/T.
7-73
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-86
Solution
We are to generate a dimensionless relationship between the given parameters.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane. 3 The flow is fully developed.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are five parameters in this problem; n = 5,
⎛ dP
⎞
u = f ⎜ h,
, μ, y ⎟
dx
⎝
⎠
List of relevant parameters:
n=5
(1)
Step 2 The primary dimensions of each parameter are listed,
u
h
{L t }
{L }
1 −1
μ
dP/dx
{m L
1 −2 −2
1
t
y
} {m L t }
1 −1 −1
{L }
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. We cannot pick both h and y since they have the same
dimensions. We choose
h, dP/dx, and μ
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
b1
⎛ dP ⎞ c1
Π1 = uh a1 ⎜
⎟ μ
⎝ dx ⎠
mass:
{m } = {m
time:
{t } = {t
length:
0
0
m c1
}
−1 −2 b1 − c1
{L } = {L L
0
b1
t
t
}
1 a1 −2b1 − c1
L
L
}
{( L t
1 −1
)( L ) ( m L
1
a1
1 −2 −2
t
) (m L
b1
1 −1 − 1
t
)
c1
}
0 = b1 + c1
c1 = −b1
0 = −1 − 2b1 − c1
b1 = −1
0 = −1 − b1
c1 = 1
a1 = −2
0 = 1 + a1 − 2b1 − c1
0 = 1 + a1 + 1
The dependent Π is thus
Π 1:
μu
Π1 =
h
2
dP
dx
The independent Π is generated with variable y. Since {y} = {L}, and this is the same as one of the repeating variables (h),
Π2 is simply y/h,
7-74
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Π2 =
Π 2:
y
h
Step 6 We write the final functional relationship as
Relationship between Πs:
Π1 =
μu
⎛ y⎞
= f⎜ ⎟
dP
⎝h⎠
h2
dx
(2)
Discussion
If we were to solve this problem exactly (using the methods of Chap. 9) we would see that the functional
relationship of Eq. 2 is correct.
7-87
Solution
We are to generate a dimensionless relationship between the given parameters and then analyze the
behavior of umax when an independent variable is doubled.
Assumptions
1 The flow is steady. 2 The flow is two-dimensional in the x-y plane. 3 The flow is fully developed.
Analysis
(a) A step-by-step dimensional analysis procedure could be performed. However, we notice that umax has
the same dimensions as u. Therefore the algebra would be identical to that of the previous problem except that there is only
one Π instead of two since y is no longer a parameter. The result is
Relationship between Πs:
Π1 =
μ umax
dP
h
dx
= constant = C
2
(1)
or
Final relationship for umax:
umax = C
h 2 dP
μ dx
(2)
Alternatively, we can use the results of the previous problem directly. Namely, since we know that the maximum velocity
occurs at the centerline, y/h = 1/2 there, and is a constant. Hence, Eq. 2 of the previous problem reduces to Eq. 1 of the
present problem.
(b) If h doubles, we see from Eq. 2 that umax will increase by a factor of 22 = 4.
(c) If dP/dx doubles, we see from Eq. 2 that umax will increase by a factor of 21 = 2.
(d) Since there is only one Π in this problem, we would need to conduct only one experiment to determine the constant C in
Eq. 2.
Discussion
The constant turns out to be -1/8, but there is no way to determine this from dimensional analysis alone. To
obtain the constant, we would need to either do an experiment, or solve the problem exactly using the methods discussed in
Chap. 9.
7-75
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-88 [Also solved using EES on enclosed DVD]
Solution
We are to generate a relationship for Darcy friction factor f in terms of Euler number Eu. We are then to
plot f as a function of Re and discuss whether Reynolds number independence has been achieved.
Assumptions 1 The flow is fully developed. 2 The flow is steady and
incompressible.
0.0495
Properties
For water at T = 20 C and atmospheric pressure, ρ =
998.0 kg/m3 and μ = 1.002 × 10-3 kg/m⋅s.
0.0494
o
0.0493
0.0492
Analysis
(a) Since the flow is fully developed, the control volume
cuts through two cross sections in which the velocity profiles are
identical. The flow is also steady, so the control volume momentum
equation in the horizontal (x) direction reduces to
0.0491
f
0.0489
0.0488
Conservation of momentum:
∑F = ∑F
x
x , pressure
0.0487
(1)
+ ∑ Fx , shear stress = 0
0.0486
0.0485
We multiply pressure by cross-sectional area to obtain the pressure force,
and wall shear stress times inner pipe wall surface area to obtain the shear
stress force,
∑ Fx, pressure = ΔP
π D2
4
Reynolds number
independence
0.049
∑F
x , shear stress
= −τ wπ DL
(2)
Note the negative sign in the shear stress term since τw points to the left.
We substitute Eq. 2 into Eq. 1. After some algebra,
ΔP =
Result:
0
2
Re × 10-6
4
6
FIGURE 1
Nondimensionalized experimental data from
a section of pipe.
4τ w L
D
(3)
Finally, we divide both sides of Eq. 3 by ρV2 to convert ΔP into an Euler number,
Eu =
Nondimensional relationship:
4τ w L 1 L ⎛ 8τ w ⎞
ΔP
=
=
⎜
⎟
2
ρV
ρV 2 D 2 D ⎝ ρV 2 ⎠
(4)
We recognize the term in parentheses on the right as the Darcy friction factor. Thus,
Final nondimensional relationship:
Eu =
1 L
f
2D
or
f =2
D
Eu
L
(5)
(b) We use Eq. 5 to calculate f at each data point of Table P7-74. We plot f as a function of Re in Fig. 1. We see that the
behavior of f mimics that of Eu (as it must because of Eq. 5 where we see that f is just a constant times Eu). Since
Eu shows Reynolds number independence for Re greater than about 2 × 106, so does f. We see Reynolds number
independence for Re greater than about 2 × 106. From the plot, the extrapolated value of f at large Re is about
0.04867, which agrees with Eq. 5 when we plug in the Re-independent value of Eu,
Extrapolated value of f:
f =2
0.104 m
D
Eu = 2
( 0.3042 ) = 0.0487
L
1.3 m
(6)
Discussion
We show in Chap. 8 (the Moody chart) that f does indeed flatten out at high enough values of Re, depending
on the relative roughness height, ε/D.
7-76
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-89
Solution
We are to create characteristic scales so that we can define a desired established dimensionless parameter.
Analysis
(a) For Froude number we need a velocity scale, a length scale, and gravity. We already have a length
scale and gravity. We create a velocity scale as V ′ / L . We then define a Froude number as
Fr =
Froude number:
V
gL
=
V ′
L gL
=
V ′
gL3
(b) For Reynolds number we need a velocity scale, a length scale, and kinematic viscosity. Of these we only have the
kinematic viscosity, so we need to create a velocity scale and a length scale. After a “back of the envelope” analysis, we
create a velocity scale as V ′ / L where L is some undefined characteristic length scale. Thus,
Re =
Reynolds number:
LV
ν
=
LV ′ V ′
=
Lν
ν
Note that in this case, the length scales drop out, so it doesn’t matter that we could not define a length scale from the given
parameters.
(c) For Richardson number we need a length scale, the gravitational constant, a volume flow rate, a density, and a density
difference. Of these we have all but the volume flow rate, so we create a volume flow rate scale as V ′ L . Thus,
Richardson number:
Discussion
Ri =
L5 g Δρ
L5 g Δρ
L3 g Δρ
=
=
2
2
2
ρV
ρ V ′L
ρ V ′
( )
( )
You can verify that each of the parameters above is dimensionless.
7-77
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-90
Solution
We are to find the functional relationship between the given parameters and name any established
dimensionless parameters.
Assumptions
1 The given parameters are the only ones relevant to the flow at hand.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are seven parameters in this problem; n = 7,
V = f ( d , D, ρ , μ , h, g )
List of relevant parameters:
n=7
(1)
Step 2 The primary dimensions of each parameter are listed,
V
d
D
{L t }
{L }
{L }
1 −1
1
ρ
μ
{m L } {m L t }
1 −3
1
1 −1 −1
h
g
{L }
{L t }
1
1 −2
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 7−3 = 4
Step 4 We need to choose three repeating parameters since j = 3. We pick length scale h, fluid density ρ, and gravitational
constant g.
h, ρ , and g
Repeating parameters:
Step 5 The Πs are generated. Note that in this case we do the algebra in our heads since these relationships are very
simple. The dependent Π is
Π1 = a Froude number:
Π1 =
V
gh
This Π is a type of Froude number. Similarly, the two length-scale Πs are obtained easily,
Π 2:
Π2 =
d
h
Π3 =
D
h
and
Π 3:
Finally, the Π formed with viscosity is generated,
{Π 4 } =
Π 4 = μ h a4 ρ b4 g c4
mass:
{m } = {m m }
time:
{t } = { t
0
0
1
b4
−1 −2 c4
t
}
{( m L t
1 −1 −1
)( L ) ( m L ) ( L t )
1
a4
1 −3
b4
1 −2
c4
}
b4 = −1
0 = 1 + b4
0 = −1 − 2c4
c4 = −
1
2
7-78
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
length:
{L } = {L
0
L L−3b4 Lc4
−1 a4
}
0 = −1 + a4 − 3b4 + c4
0 = −1 + a4 + 3 −
a4 = −
1
2
3
2
which yields
Π 4:
Π4 =
μ
3
ρh2 g
We recognize this Π as the inverse of a kind of Reynolds number. We also split the h terms to separate them into a length
scale and (when combined with g) a velocity scale. The final form is
Modified Π4 = a Reynolds number:
Π4 =
ρ h gh
μ
Step 6 We write the final functional relationship as
Relationship between Πs:
⎛ d D ρ h gh
= f⎜ , ,
⎜h h
μ
gh
⎝
V
⎞
⎟
⎟
⎠
(2)
Discussion
You may choose different repeating variables, and may generate different nondimensional groups. If you do
the algebra correctly, your answer is not “wrong” – you just may not get the same dimensionless groups.
7-79
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-91
Solution
We are to find a dimensionless relationship among the given parameters.
Assumptions
1 The given parameters are the only ones relevant to the flow at hand.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are seven parameters in this problem; n = 7,
tempty = f ( d , D, ρ , μ , h, g )
List of relevant parameters:
n=7
(1)
Step 2 The primary dimensions of each parameter are listed,
tempty
d
D
{t }
{L }
{L }
1
1
ρ
μ
{m L } {m L t }
1 −3
1
1 −1 −1
h
g
{L }
{L t }
1
1 −2
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 7−3 = 4
Step 4 We need to choose three repeating parameters since j = 3. We pick length scale h, fluid density ρ, and gravitational
constant g. (Note: these are the same repeating parameters as in the previous problem.)
h, ρ , and g
Repeating parameters:
Step 5 The Πs are generated. We leave out the details since the algebra is trivial and can be done by inspection in
most cases. The dependent Π is
Π 1:
Π1 = tempty
g
h
The rest of the Πs are identical to those of the previous problem.
Step 6 We write the final functional relationship as
Relationship between Πs:
tempty
⎛ d D ρ h gh ⎞
g
= f⎜ , ,
⎟
⎜h h
h
μ ⎟⎠
⎝
(2)
Discussion
You may choose different repeating variables, and may generate different nondimensional groups. If you do
the algebra correctly, your answer is not “wrong” – you just may not get the same dimensionless groups.
7-80
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-92
Solution
We are to calculate the temperature of water in a model test to ensure similarity with the prototype, and we
are to predict the time required to empty the prototype tank.
Assumptions 1 The parameters specified in the previous problem are the only parameters relevant to the problem. 2 The
model and prototype are geometrically similar.
Properties
For ethylene glycol at 60oC, ν = μ/ρ = 4.75×10-6 m2/s (given).
Analysis
(a) We use the functional relationship obtained in the previous problem,
tempty
Dimensionless relationship:
⎛ d D ρ h gh ⎞
g
= f⎜ , ,
⎟
⎜h h
h
μ ⎟⎠
⎝
(1)
Since the model and prototype are geometrically similar, (d/h)model = (d/h)prototype and (D/h)model = (D/h)prototype. Thus, we are
left with only one Π to match to ensure similarity. Namely, the Reynolds number parameter in Eq. 1 must be matched
between model and prototype. Since g remains the same in either case, and using “m” for model and “p” for prototype,
⎛ ρ h gh ⎞
⎛ ρ h gh
⎜
⎟ =⎜
⎜ μ ⎟
⎜
⎝
⎠m ⎝ μ
Similarity:
3
⎞
ρ p ⎛ hp ⎞ 2
ρ
⎟ or m =
⎜ ⎟
⎟
μ m μ p ⎝ hm ⎠
⎠p
(2)
We recognize that ν = μ/ρ, and we know that hp/hm = 4. Thus, Eq. 2 reduces to
−3
Similarity:
−3
⎛ h ⎞2
ν m = ν p ⎜ p ⎟ = 4.75 × 10−6 m 2 /s ( 4 ) 2 = 5.94 × 10−7 m 2 /s
⎝ hm ⎠
(3)
For similarity we need to find the temperature of water where the kinematic viscosity is 5.94×10-7 m2/s. By interpolation
from the property tables, the designers should run the model tests at a water temperature of 45.8oC.
(b) At dynamically similar conditions, Eq. 1 yields
At dynamically similar conditions:
⎛
g⎞ ⎛
g⎞
⎜⎜ tempty
⎟⎟ = ⎜⎜ tempty
⎟
h ⎠p ⎝
h ⎟⎠ m
⎝
→ tempty,p = tempty,m
hp
hm
= 4.53 min 4 = 9.06 min
(5)
Discussion
We set up Eqs. 3 and 5 in terms of ratios of hp to hm so that the actual dimensions are not needed – just the
ratio is needed, and it is given.
7-81
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-93
Solution
doubled.
For the simplified case in which V depends only on h and g, we are to determine how V increases when h is
Assumptions
1 The given parameters are the only ones relevant to the problem.
Analysis
We employ the dimensional analysis results of Problem 7-90. Dropping d, D, ρ, and μ from the list of
parameters, we are left with n = 3,
V = f ( h, g )
List of relevant parameters:
n=3
(1)
We perform the analysis in our heads –only one Π remains, and it is therefore set to a constant. The final result of the
dimensional analysis is
V
Relationship between Πs:
gh
= constant
(2)
Thus, when h is doubled, we can easily calculate the factor by which V increases,
V2
Increase in V:
gh2
=
V1
gh1
or V2 = V1
h2
= V1 2
h1
Thus, when h increases by a factor of 2, V increases by a factor of
(3)
2.
Discussion
We don’t need to know the constant in Eq. 2 to solve the problem. However, it turns out that the constant is
2 (see Chap. 5).
7-94
Solution
We are to verify the dimensions of particle relaxation time τp, and then identify the established
dimensionless parameter formed by nondimensionalization of τp.
Analysis
First we obtain the primary dimensions of τp,
Primary dimensions of τp:
{τ }
p
⎧m
2 ⎫
⎪⎪ L3 × L ⎪⎪
=⎨
⎬ = {t}
⎪ m ⎪
⎩⎪ Lt ⎭⎪
A characteristic time scale for the air flow is L/V. Thus, we nondimensionalize τp,
Nondimensionalized particle relaxation time:
τ p* = τ p =
ρ p d p2 V
18μ L
From Table 7-5 we recognize this as the Stokes number, Stk,
Stokes number:
Discussion
Stk =
ρ p d p 2V
18μ L
Stokes number is useful when studying the flow of aerosol particles.
7-82
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-95
Solution
We are to compare the primary dimensions of each given property in mass-based and force-based primary
dimensions, and discuss.
Analysis
From previous problems and examples in this chapter, we can write down the primary dimensions of each
property in the mass-based system. We use the fundamental definitions of these quantities to generate the primary
dimensions in the force-based system:
(a) For pressure P the primary dimensions are
Mass-based primary dimensions
Force-based primary dimensions
{P} = ⎧⎨
m ⎫
2 ⎬
⎩t L⎭
{P} = ⎧⎨
force ⎫ ⎧ F ⎫
⎬=⎨ 2⎬
⎩ area ⎭ ⎩ L ⎭
G
(b) For moment M the primary dimensions are
Mass-based primary dimensions
G
Force-based primary dimensions
G
M = {force × moment arm} = {FL}
{ }
{M } = ⎧⎨⎩m Lt ⎫⎬⎭
2
2
(c) For energy E the primary dimensions are
Mass-based primary dimensions
Force-based primary dimensions
⎧
{E} = {force × distance} = {FL}
{E} = ⎨m
⎩
L2 ⎫
⎬
t2 ⎭
We see that (in these three examples anyway), the forced-base cases have only two primary dimensions represented (F and
L), whereas the mass-based cases have three primary dimensions represented (m, L, and t). Some authors would prefer the
force-based system because of its reduced complexity when dealing with forces, pressures, energies, etc.
Discussion
Not all variables have a simpler form in the force-based system. Mass itself for example has primary
dimensions of {m} in the mass-based system, but has primary dimensions of {Ft2/L} in the force-based system. In
problems involving mass, mass flow rates, and/or density, the force-based system may not have any advantage.
7-83
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-96
Solution
The pressure difference between the inside of a soap bubble and the outside air is to be analyzed with
dimensional analysis and the method of repeating variables using the force-based system of primary dimensions.
Assumptions 1 The soap bubble is neutrally buoyant in the air, and gravity is not relevant. 2 No other variables or
constants are important in this problem.
Analysis
The step-by-step method of repeating variables is employed.
Step 1 There are three variables and constants in this problem; n = 3,
ΔP = f ( R, σ s )
n=3
(1)
Step 2 The primary dimensions of each parameter are listed. The dimensions of pressure are force per area and those of
surface tension are force per length.
ΔP
R
σs
{F L }
{L }
{F L }
1 −2
1 −1
1
Step 3 As a first guess, j is set equal to 2, the number of primary dimensions represented in the problem (F and L).
j=2
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n − j = 3− 2 =1
Step 4 We choose two repeating parameters since j = 2. Our only choice is R and σs since ΔP is the dependent variable.
Step 5 The dependent Π is generated:
{Π1} = {F0 L0 } =
Π1 = ΔPR a1 σ s b1
force:
length:
{F } = {F F }
0
0
−2
La1 L− b1
}
1 −2
) L (F L )
a1
1 −1
b1
}
0 = 1 + b1
b1 = −1
0 = −2 + a1 − b1
a1 = 1
1 b1
{L } = {L
{( F L
a1 = 2 + b1
Eq. 1 thus becomes
Π 1:
Π1 =
ΔPR
(2)
σs
From Table 7-5, the established nondimensional parameter most similar to Eq. 2 is the Weber number, defined as a
pressure times a length divided by surface tension. There is no need to further manipulate this Π.
Step 6 We now write the functional relationship between the nondimensional parameters. Since there is only one Π, it is a
function of nothing, which means it must be a constant,
Relationship between Πs:
Π1 =
ΔPR
σs
= f ( nothing ) = constant
→
ΔP = constant
σs
R
(3)
The result using force-based primary dimensions is indeed identical to the previous result using the mass-based system.
Discussion
Because only two primary dimensions are represented in the problem when using the force-based system,
the algebra is in fact a lot easier.
7-84
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-97
Solution
We are to a third established nondimensional parameter that is formed by the product or ratio of two given
established nondimensional parameters.
Analysis
(a) The product of Reynolds number and Prandtl number yields
Reynolds number times Prandtl number:
Re × Pr =
ρ LV cP μ ρ LVcP
×
=
μ
k
k
(1)
We recognize Eq. 1 as the Peclet number,
Pe = Re × Pr =
Peclet number:
ρ LVcP
k
=
LV
α
(2)
(b) The ratio of Schmidt number and Prandtl number yields
μ
Schmidt number divided by Prandtl number:
k
Sc ρ DAB
=
=
μ
c
ρ cP DAB
Pr
P
k
(3)
We recognize Eq. 3 as the Lewis number,
Le =
Lewis number:
k
Sc
α
=
=
Pr ρ cP DAB DAB
(4)
(c) The product of Reynolds number and Schmidt number yields
Reynolds number times Schmidt number:
Re × Sc =
ρ LV
μ
LV
×
=
μ
ρ DAB DAB
(5)
We recognize Eq. 5 as the Sherwood number,
Sherwood number:
Discussion
Sh = Re × Sc =
LV
DAB
(6)
Can you find any other such combinations from Table 7-5?
7-85
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-98
Solution
We are to determine the relationship between four established nondimensional parameters, and then try to
form the Stanton number by some combination of only two other established dimensionless parameters.
Analysis
We manipulate Re, Nu, and Pr, guided by the known result. After some trial and error,
Stanton number:
Lh
Nu
h
k
=
=
St =
ρ
Re × Pr ρVL μ cP
c pV
×
μ
k
(1)
We recognize from Table 7-5 (or from the previous problem) that Peclet number is equal to the product of Reynolds
number and Prandtl number. Thus,
Stanton number:
Lh
Nu
h
k
=
=
St =
ρ LVcP ρ c pV
Pe
k
(2)
Discussion
Not all named, established dimensionless parameters are independent of other named, established
dimensionless parameters.
7-99
Solution
We are to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
First we do some thinking. If we imagine traveling at the same speed as the bottom plate, the flow would
be identical to that of Problem 7-56 except that the top plate speed would be (Vtop – Vbottom) instead of just V. The step-bystep method of repeating variables is otherwise identical to that of Problem 7-56, and the details are not included here. The
final functional relationship is
Relationship between Πs:
Vtop
u
y⎞
⎛
= f ⎜ Re, ⎟
− Vbottom
h⎠
⎝
(1)
where
Reynolds number:
Re =
ρ (Vtop − Vbottom ) h
μ
(2)
Discussion
It is always wise to look for shortcuts like this to save us time.
7-100
Solution
We are to determine the primary dimensions of electrical charge.
Analysis
The fundamental definition of electrical current is charge per unit time. Thus,
Primary dimensions of charge:
{q} = {current × time} = {I t}
(1)
Or, in exponent form, {q} = {t1 I1}.
Discussion
dimensions.
We see that all dimensions, even those of electrical properties, can be expressed in terms of primary
7-86
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-101
Solution
We are to determine the primary dimensions of electrical capacitance.
Analysis
Electrical capacitance C is measured in units of farads (F). By definition, a one-farad capacitor with an
applied electric potential of one volt across it will store one coulomb of electrical charge. Thus,
Primary dimensions of capacitance:
⎧
⎪ It
{C} = {charge / voltage} = ⎨⎪ 2
⎪ mL
⎩⎪ t 3 I
⎫
⎪⎪ ⎧ I 2 t 4 ⎫
⎬=⎨
2 ⎬
⎪ ⎩ mL ⎭
⎭⎪
(1)
where the primary dimensions of voltage are obtained from Problem 7-10, and those of electric charge are obtained from
the previous problem. Or, in exponent form, {C} = {m-1 L-2 t4 I2}.
Discussion
dimensions.
7-102
Solution
our result.
We see that all dimensions, even those of electrical properties, can be expressed in terms of primary
We are to determine the primary dimensions of electrical time constant RC, and discuss the significance of
Analysis
The primary dimensions of electrical resistance are obtained from Problem 7-11. Those of electrical
capacitance C are obtained from the previous problem. Thus,
Primary dimensions of electrical time constant RC:
⎧ mL2 I 2 t 4 ⎫
×
⎬ = {t}
3 2
mL2 ⎭
⎩t I
{RC} = {resistance × capacitance} = ⎨
(1)
Thus we see that the primary dimensions of RC are those of time. This explains why a resistor and capacitor in series is
often used in timing circuits.
Discussion
The cut-off frequency of the low-pass filter is proportional to 1/R⋅C. If the resistor and the capacitor were to
swap places we would have a high-pass rather than a low-pass filter.
7-103
Solution
We are to determine the primary dimensions of both sides of the equation, and we are to verify that the
equation is dimensionally homogeneous.
Analysis
The primary dimensions of the time derivative (d/dt) are 1/time. The primary dimensions of capacitance are
current2×time4 / (mass×length2), as obtained from Problem 7-101. Thus both sides of the equation can be written in terms of
primary dimensions,
{I } = {current}
⎧
mass × length 2
2
4
dE ⎪⎪ current × time current × time3
C
=⎨
time
dt ⎪ mass × length 2
⎩⎪
{I } = {I}
⎫
⎪⎪
⎬ = {current}
⎪
⎭⎪
⎧ dE ⎫
⎨C
⎬ = {I}
⎩ dt ⎭
Indeed, both sides of the equation have the same dimensions, namely {I}.
Discussion
Current is one of our seven primary dimensions. These results verify our algebra in Problem 7-101.
7-87
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-104
Solution
We are to find the functional relationship between the given parameters, and then answer some questions
about scaling.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
(a) The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the Πs).
Step 1 There are four parameters in this problem; n = 4,
(
δ P = f ρ ,V , D
List of relevant parameters:
)
n=4
(1)
Step 2 The primary dimensions of each parameter are listed,
δP
ρ
V
D
{m L t }
{m L }
{L t }
{L }
1 −1 −2
1 −3
3 −1
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j =3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−3 =1
Step 4 We need to choose three repeating parameters since j = 3. We only have one choice in this problem, since there are
only three independent parameters on the right-hand side of Eq. 1,
ρ, V , and D
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = δ P ρ a1V b1 D c1
{( m L t
1 −1 −2
)( m L ) ( L t ) ( L )
1 −3
a1
3 −1
b1
1
c1
}
mass:
{m } = {m }
0 = 1 + a1
a1 = −1
time:
{t } = {t }
0 = −2 − b1
b1 = −2
0 = −1 − 3a1 + 3b1 + c1
c1 = 4
length:
1+ a1
0
−2 − b1
0
{L } = {L
0
−1 −3a1 3b1 c1
L
L L
}
The dependent Π is thus
Π 1:
Π1 =
D 4δ P
ρV 2
Step 6 Since there is only one Π, it is a function of nothing. This is only possible if we set the Π equal to a constant. We
write the final functional relationship as
Relationship between Πs:
Π1 =
D 4δ P
= constant
ρV 2
(2)
7-88
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
(b) We re-write Eq. 2 as
Equation for δP:
δ P = constant
ρV 2
D4
(3)
Thus, if we double the size of the cyclone, the pressure drop will decrease by a factor of 24 = 16.
(c) Also from Eq. 3 we see that if we double the volume flow rate, the pressure drop will increase by a factor of 22 =
4.
Discussion
The pressure drop would be smallest for the largest cyclone operating at the smallest volume flow rate.
(This agrees with our intuition.)
7-89
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-105
Solution
We are to find the functional relationship between the given parameters, and then answer some questions
about scaling.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
(a) The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the Πs).
Step 1 There are five parameters in this problem; n = 5,
(
w = f q p , E f , μ , Dp
List of relevant parameters:
)
n=5
(1)
Step 2 The primary dimensions of each parameter are listed,
w
qp
{L t }
{I t }
1 −1
μ
Ef
{m L t
1 1 −3 − 1
1 1
I
Dp
} {m L t }
{L }
1 −1 −1
1
where the primary dimensions of voltage are obtained from Problem 7-10, and those of electric charge are obtained from
Problem 7-100.
Step 3 As a first guess, j is set equal to 4, the number of primary dimensions represented in the problem (m, L, t, and I).
j=4
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−4 =1
Step 4 We need to choose four repeating parameters since j = 4. We only have one choice in this problem, since there are
only four independent parameters on the right-hand side of Eq. 1,
qp, E, Dp, and μ
Repeating parameters:
Step 5 The dependent Π is generated:
{Π1} =
Π1 = wq p a1 E f b1 μ c1 D p d1
{I } = {I
current:
mass:
time:
length:
0
{m } = {m
0
{t } = {t
0
I
}
b1
m c1
a1 − b1
{L } = {L L L
0
1 −1
}
−1 a1 −3b1 − c1
t t
{( L t
t
1 b1 − c1 d1
L
)( I t ) ( m L t
1 1
a1
1 1 −3 −1
I
) (m L
b1
1 −1 −1
t
) (L )
c1
1
d1
}
0 = a1 − b1
a1 = b1
0 = b1 + c1
c1 = −b1 = − a1
}
0 = −1 + a1 − 3b1 − c1
}
0 = 1 + b1 − c1 + d1
a1 = b1 = −1
c1 = 1
d1 = 1
The dependent Π is thus
Π 1:
Π1 =
wμ D p
qp E f
7-90
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Step 6 Since there is only one Π, it is a function of nothing. This is only possible if we set the Π equal to a constant. We
write the final functional relationship as
Relationship between Πs:
Π1 =
wμ D p
qp E
= constant
(2)
(b) We re-write Eq. 2 as
Equation for w:
w = constant
qp E f
μ Dp
(3)
Thus, if we double the electric field strength, the drift velocity will increase by a factor of 2.
(c) Also from Eq. 3 we see that if we double the particle size, the drift velocity will decrease by a factor of 2.
Discussion
These results agree with our intuition. Certainly we would expect the drift velocity to increase if we
increase the field strength. Also, larger particles have more aerodynamic drag, so for the same charge, we would expect a
larger dust particle to drift more slowly than a smaller dust particle.
7-91
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-106
Solution
We are to generate a dimensionless functional relationship between the given parameters and then compare
our results with a known exact analytical solution.
Assumptions
problem.
Analysis
1 There is no flow (hydrostatics). 2 The parameters listed here are the only relevant parameters in the
(a) We perform a dimensional analysis using the method of repeating variables.
Step 1 There are five parameters in this problem; n = 6,
h = f ( ρ , g , σ s , D, φ )
List of relevant parameters:
n=6
(1)
Step 2 The primary dimensions of each parameter are listed,
h
ρ
g
σs
D
φ
{L }
{m L }
{L t }
{m t }
{L }
{1}
1 −3
1
1 −2
1 −2
1
Note that the dimensions of the contact angle are unity (angles are dimensionless).
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 6−3 = 3
Step 4 We need to choose three repeating parameters since j = 3. We cannot choose φ since it is dimensionless. We
choose a length (D) and a density (ρ). We’d rather have gravitational constant g than surface tension σs in our Πs. So, we
choose
ρ, g, D
Repeating parameters:
Step 5 The dependent Π is generated. Since h has the same dimensions as D, we immediately write
Π 1:
Π1 =
h
D
The first independent Π is generated by combining σs with the repeating parameters,
{Π 2 } =
Π 2 = σ s ρ a2 g b2 D c2
mass:
{m } = {m m }
time:
{t } = { t
length:
0
1
0
{L } = {L
0
a2
−2 −2 b2
t
}
−3a2 b2 c2
L L
}
{( m t
1 −2
)( m L ) ( L t ) ( L )
1 −3
a2
1 −2
b2
1
c2
}
0 = 1 + a2
a2 = −1
0 = −2 − 2b2
b2 = −1
0 = −3a2 + b2 + c2
c2 = −2
c2 = 3a2 − b2
The first independent Π is thus
Π 2:
Π2 =
σs
ρ gD 2
Finally, the third Π (second independent Π) is simply angle φ itself since it is dimensionless,
7-92
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
Π3 = φ
Π 3:
Step 6 We write the final functional relationship as
⎛ σs
⎞
h
= f⎜
,φ ⎟
2
D
⎝ ρ gD
⎠
Relationship between Πs:
(2)
(b) From Chap. 2 we see that the exact analytical solution is
h=
Exact relationship:
4σ s
cos φ
ρ gD
(3)
Comparing Eqs. 2 and 3, we see that they are indeed of the same form. In fact,
Functional relationship:
Π1 = constant × Π 2 × cos Π 3
(4)
Discussion
We cannot determine the constant in Eq. 4 by dimensional analysis. However, one experiment is enough to
establish the constant. Or, in this case we can find the constant exactly. Viscosity is not relevant in this problem since there
is no fluid motion.
7-107
Solution
tube.
Assumptions
parameter.
We are to find a functional relationship for the time scale required for the liquid to climb up the capillary
1 trise is a function of the same parameters listed in the previous problem, but there is another relevant
Analysis
Since this is an unsteady problem, the rise time will surely depend also on fluid viscosity μ. The list of
parameters now involves seven parameters,
List of relevant parameters:
trise = f ( ρ , g , σ s , D, φ , μ )
n=7
(1)
and we expect four Πs. We choose the same repeating parameters and the algebra is similar to that of the previous problem.
It turns out that
Π 1:
Π1 = trise
g
D
The second and third Π are the same as those of the previous problem. Finally, the fourth Π is formed by combining μ
with the repeating parameters. We expect some kind of Reynolds number. We can do the algebra in our head. Specifically,
a velocity scale can be formed as gD . Thus,
Π 4:
Π 4 = Re =
ρ D gD
μ
The final functional relationship is
Relationship between Πs:
Discussion
trise
⎛ σs
⎞
g
= f⎜
, φ , Re ⎟
2
D
ρ
gD
⎝
⎠
If we would have defined a time scale as
(2)
D / g , we could have written Π1 by inspection as well, saving
ourselves some algebra.
7-93
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-108
Solution
We are to use dimensional analysis to find the functional relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are four parameters in this problem; n = 4,
I = f ( P, c, ρ )
List of relevant parameters:
n=4
(1)
Step 2 The dimensions of I are those of power per area. The primary dimensions of each parameter are listed,
I
P
ρ
c
{m t } {m L t } {L t } { m L }
1 −3
1 −1 −2
1 −1
1 −3
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−3 =1
Step 4 We need to choose three repeating parameters since j = 3. The problem is that the three independent parameters
form a Π all by themselves (c2ρ/P is dimensionless). Let’s see what happens if we don’t notice this, and we pick all three
independent parameters as repeating variables,
P, ρ , and c
Repeating parameters:
Step 5 The Π is generated:
{Π1} =
Π1 = I × P a ρ b c c
mass:
{m } = { m m m }
time:
{t } = {t
length:
0
0
1
t
−a
t
1 −3
}
L−3b Lc
}
)( m L
1 −1 −2
t
) (m L ) (L t ) }
a
1 −3
b
1 −1
c
0 = 1+ a + b
a = −1 − b
0 = −3 − 2a − c
c = −1 + 2b
b
−3 −2 a − c
{L } = { L
0
a
{( m t
c = −3 − 2a
0 = − a − 3b + c
c = −1 + 2b
c = a + 3b
This is a situation in which two of the equations agree, but we cannot solve for unique exponents. If we knew b, we could
get a and c. The problem is that any value of b we choose will make the Π dimensionless. For example, if we choose b = 1,
we find that a = –2 and c = 1, yielding
Π1 for the case with b = 1:
Π1 =
I ρc
P2
Since there is only one Π, we write
Functional relationship for the case with b = 1:
I = constant ×
P2
ρc
(2)
7-94
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
However, if we choose a different value of b, say b = –1, then a = 0 and c = –3, yielding
Π1 for the case with b = –1:
Π1 =
I
ρ c3
Since there is only one Π, we write
I = constant × ρ c3
Functional relationship for the case with b = –1:
(3)
Similarly, you can come up with a whole family of possible answers, depending on your choice of b. We double check our
algebra and realize that any value of b works. Hence the problem is indeterminate with three repeating variables.
We go back now and realize that something is wrong. As stated previously, the problem is that the three
independent parameters can form a dimensionless group all by themselves. This is another case where we have to reduce j
by 1. Setting j = 3 – 1 = 2, we choose two repeating parameters,
ρ and c
Repeating parameters:
We jump to Step 5 of the method of repeating variables,
Step 5 The first Π is generated:
{Π1} =
Π1 = I ρ a c b
mass:
{m } = { m m }
time:
{t } = {t
length:
{L } = { L
0
1
0
−3 − b
t
−3 a
0
a
}
Lb
}
{( m t
1 −3
)( m L ) ( L t ) }
1 −3
a
1 −1
b
0 = 1+ a
a = −1
0 = −3 − b
b = −3
0 = −3a + b
b = −3
b = 3a
Fortunately, the results for time and length agree. The dependent Π is thus
Π 1:
Π1 =
I
ρ c3
We form the second Π with sound pressure P,
{Π 2 } =
Π 2 = Pρ ec f
mass:
{m } = { m m }
time:
{t } = { t
length:
0
1
0
{L } = { L
0
−2 − f
t
−1 −3e
e
}
L Lf
}
{( m L t
1 −1 −2
)( m L ) ( L t )
1 −3
e
1 −1
f
}
0 = 1+ e
e = −1
0 = −2 − f
f = −2
0 = −1 − 3e + f
f = −2
f = 1 + 3e
The second Π is thus
Π 2:
Π2 =
P
ρ c2
Step 6 We write the final functional relationship as
7-95
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
⎛ P ⎞
I
= f⎜ 2⎟
3
ρc
⎝ ρc ⎠
Relationship between Πs:
(4)
(b) We try the force-based primary dimension system instead.
Step 1 There are four parameters in this problem; n = 4,
I = f ( P, c, ρ )
List of relevant parameters:
n=4
(5)
Step 2 The dimensions of I are those of power per area. The primary dimensions of each parameter are listed,
I
P
ρ
c
{F L t } {F L } {L t } {F t L }
1 −1 −1
1 −2
1 −1
1 2
−4
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (F, L, and t).
Again, however, the three independent parameters form a dimensionless group all by themselves. Thus we lower j by 1.
j=2
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 4−2 = 2
Step 4 We need to choose two repeating parameters since j = 2. We pick the same two parameters as in Part (a),
ρ and c
Repeating parameters:
Step 5 The first Π is generated:
{Π1} =
Π1 = I × ρ b c c
{( F L t
{F } = { F F }
force:
0
{t } = {t
time:
0
length:
1
t t
{L } = { L
−1 −4 b
0
}
L Lc
}
)( F t L ) ( L t ) }
1 2
b
−4
c
1 −1
0 = 1+ b
b = −1
0 = −1 + 2b − c
c = −3
b
−1 2 b − c
1 −1 −1
c = −1 + 2b
c = −3
0 = −1 − 4b + c
c = 1 + 4b
Again the two results for length and time agree. The dependent Π is thus
Π 1:
Π1 =
I
ρ c3
We form the second Π with sound pressure P,
{Π 2 } =
Π2 = P × ρ ec f
force:
{F } = { F F }
0
1
e
{( F L
1 −2
)( F t L ) ( L t )
1 2
−4
e
1 −1
f
}
e = −1
0 = 1+ e
7-96
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
time:
length:
{t } = {t
0
{L } = { L
0
−2 e − f
−2
t
0 = −2e − f
}
L−4 e Lf
f = −2
f = −2e
}
0 = −2 − 4e + f
f = −2
f = 2 + 4e
The second Π is thus
Π 2:
Π2 =
P
ρ c2
Step 6 We write the final functional relationship as
Relationship between Πs:
I
ρ c3
⎛ P ⎞
= f⎜ 2⎟
⎝ ρc ⎠
(6)
Discussion
Equations 4 and 6 are the same. This exercise shows that you should get the same results using mass-based
or force-based primary dimensions.
7-97
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
7-109
Solution
We are to find the dimensionless relationship between the given parameters.
Assumptions
1 The given parameters are the only relevant ones in the problem.
Analysis
Πs).
The step-by-step method of repeating variables is employed to obtain the nondimensional parameters (the
Step 1 There are now five parameters in this problem; n = 5,
I = f ( P, c, ρ , r )
List of relevant parameters:
n=5
(1)
Step 2 The dimensions of I are those of power per area. The primary dimensions of each parameter are listed,
I
P
ρ
c
r
{m t } {m L t } {L t } { m L }
1 −3
1 −1 −2
1 −1
1 −3
{L }
1
Step 3 As a first guess, j is set equal to 3, the number of primary dimensions represented in the problem (m, L, and t).
j=3
Reduction:
If this value of j is correct, the expected number of Πs is
Number of expected Πs:
k = n− j = 5−3 = 2
Step 4 We need to choose three repeating parameters since j = 3. We pick the three simplest independent parameters (r
instead of P),
r , ρ , and c
Repeating parameters:
Step 5 The first Π is generated:
{Π1} =
Π1 = I × r a ρ b c c
mass:
{m } = { m m }
time:
{t } = { t
length:
0
1
0
{L } = { L L
0
a
b
−3 − c
t
−3b
{( m t
}
Lc
}
1 −3
)( L ) ( m L ) ( L t ) }
a
1
1 −3
b
1 −1
c
0 = 1+ b
b = −1
0 = −3 − c
c = −3
0 = a − 3b + c
a=0
a = 3b − c
The first Π is thus
Π 1:
Π1 =
I
ρ c3
We form the second Π with sound pressure P,
{Π 2 } =
Π2 = P × r d ρ ec f
mass:
{m } = { m m }
0
1
e
{( m L t
1 −1 −2
)( L ) ( m L ) ( L t )
1
d
1 −3
e
1 −1
f
}
e = −1
0 = 1+ e
7-98
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 7 Dimensional Analysis and Modeling
time:
length:
{t } = { t
0
{L } = { L
0
−2 − f
t
−1 d
}
L L−3e Lf
}
0 = −2 − f
f = −2
0 = −1 + d − 3e + f
d =0
d = 1 + 3e − f
The second Π is thus
Π 2:
Π2 =
P
ρ c2
Step 6 We write the final functional relationship as
Relationship between Πs:
⎛ P ⎞
I
= f⎜ 2⎟
3
ρc
⎝ ρc ⎠
(2)
Discussion
This is an interesting case in which we added another independent parameter (r), yet this new parameter
does not even appear in the final functional relationship! The list of independent parameters is thus over specified. (It turns
out that P is a function of r, so r is not needed in the problem.) The result here is identical to the result of the previous
problem. It turns out that the function in Eq. 2 is a constant times Π22, which yields the correct analytical equation for I,
namely
Analytical result:
I = constant ×
P2
ρc
(3)
KJ
7-99
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications
by Çengel & Cimbala
CHAPTER 8
FLOW IN PIPES
PROPRIETARY AND CONFIDENTIAL
This Manual is the proprietary property of The McGraw-Hill Companies, Inc.
(“McGraw-Hill”) and protected by copyright and other state and federal laws. By
opening and using this Manual the user agrees to the following restrictions, and if the
recipient does not agree to these restrictions, the Manual should be promptly returned
unopened to McGraw-Hill: This Manual is being provided only to authorized
professors and instructors for use in preparing for the classes using the affiliated
textbook. No other use or distribution of this Manual is permitted. This Manual
may not be sold and may not be distributed to or used by any student or other
third party. No part of this Manual may be reproduced, displayed or distributed
in any form or by any means, electronic or otherwise, without the prior written
permission of McGraw-Hill.
8-1
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
Laminar and Turbulent Flow
8-1C
Solution
We are to discuss why pipes are usually circular in cross section.
Analysis
Liquids are usually transported in circular pipes because pipes with a circular cross section can withstand
large pressure differences between the inside and the outside without undergoing any significant distortion.
Discussion
Piping for gases at low pressure are often non-circular (e.g., air conditioning and heating ducts in buildings).
8-2C
Solution
We are to define and discuss Reynolds number for pipe and duct flow.
Analysis
Reynolds number is the ratio of the inertial forces to viscous forces, and it serves as a criterion for
determining the flow regime. At large Reynolds numbers, for example, the flow is turbulent since the inertia forces are
large relative to the viscous forces, and thus the viscous forces cannot prevent the random and rapid fluctuations of the
fluid. It is defined as follows:
a
VD
Re =
(a) For flow in a circular tube of inner diameter D:
ν
Re =
(b) For flow in a rectangular duct of cross-section a × b:
where Dh =
b
VD h
ν
4 Ac
4ab
2ab
=
=
is the hydraulic diameter.
p
2( a + b) ( a + b)
D
Discussion
Since pipe flows become fully developed far enough downstream, diameter is the
appropriate length scale for the Reynolds number. In boundary layer flows, however, the boundary layer
grows continually downstream, and therefore downstream distance is a more appropriate length scale.
8-3C
Solution
We are to compare the Reynolds number in air and water.
Analysis
Reynolds number is inversely proportional to kinematic viscosity, which is much smaller for water than for
air (at 25°C, νair = 1.562×10-5 m2/s and νwater = μ ⁄ρ = 0.891×10-3/997 = 8.9×10-7 m2/s). Therefore, noting that Re = VD/ν,
the Reynolds number is higher for motion in water for the same diameter and speed.
Discussion
Of course, it is not possible to walk as fast in water as in air – try it!
8-4C
Solution
We are to express the Reynolds number for a circular pipe in terms of mass flow rate.
Analysis
Reynolds number for flow in a circular tube of diameter D is expressed as
VD
4m
m
m
μ
Re =
where V = Vavg =
=
=
and ν =
ν
ρ Ac ρ (π D 2 / 4 ) ρπ D 2
ρ
Discussion
m
D
Substituting,
Re =
V
VD
ν
=
4m
4mD
4m
=
. Thus, Re =
2
Dμ
π
ρπ D ( μ / ρ ) π D μ
This result holds only for circular pipes.
8-2
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-5C
Solution
We are to compare the pumping requirement for water and oil.
Analysis
Engine oil requires a larger pump because of its much larger viscosity.
Discussion
The density of oil is actually 10 to 15% smaller than that of water, and this makes the pumping requirement
smaller for oil than water. However, the viscosity of oil is orders of magnitude larger than that of water, and is therefore the
dominant factor in this comparison.
8-6C
Solution
We are to discuss the Reynolds number for transition from laminar to turbulent flow.
Analysis
The generally accepted value of the Reynolds number above which the flow in a smooth pipe is turbulent is
4000. In the range 2300 < Re < 4000, the flow is typically transitional between laminar and turbulent.
Discussion
In actual practice, pipe flow may become turbulent at Re lower or higher than this value.
8-7C
Solution
We are to compare pipe flow in air and water.
Analysis
Reynolds number is inversely proportional to kinematic viscosity, which is much smaller for water than for
air (at 25°C, νair = 1.562×10-5 m2/s and νwater = μ ⁄ρ = 0.891×10-3/997 = 8.9×10-7 m2/s). Therefore, for the same diameter and
speed, the Reynolds number will be higher for water flow, and thus the flow is more likely to be turbulent for water.
Discussion
The actual viscosity (dynamic viscosity) μ is larger for water than for air, but the density of water is so
much greater than that of air that the kinematic viscosity of water ends up being smaller than that of air.
8-8C
Solution
We are to define and discuss hydraulic diameter.
Analysis
For flow through non-circular tubes, the Reynolds number and the friction factor are based on the hydraulic
diameter Dh defined as Dh =
4 Ac
where Ac is the cross-sectional area of the tube and p is its perimeter. The hydraulic
p
diameter is defined such that it reduces to ordinary diameter D for circular tubes since D h =
4 Ac 4πD 2 / 4
=
=D.
πD
p
Discussion
Hydraulic diameter is a useful tool for dealing with non-circular pipes (e.g., air conditioning and heating
ducts in buildings).
8-9C
Solution
We are to define and discuss hydrodynamic entry length.
Analysis
The region from the tube inlet to the point at which the boundary layer merges at the centerline is
called the hydrodynamic entrance region, and the length of this region is called hydrodynamic entry length. The entry
length is much longer in laminar flow than it is in turbulent flow. But at very low Reynolds numbers, Lh is very small
(e.g., Lh = 1.2D at Re = 20).
Discussion
The entry length increases with increasing Reynolds number, but there is a significant change in entry
length when the flow changes from laminar to turbulent.
8-3
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-10C
Solution
We are to compare the wall shear stress at the inlet and outlet of a pipe.
Analysis
The wall shear stress τw is highest at the tube inlet where the thickness of the boundary layer is nearly
zero, and decreases gradually to the fully developed value. The same is true for turbulent flow.
Discussion
We are assuming that the entrance is well-rounded so that the inlet flow is nearly uniform.
8-11C
Solution
We are to discuss the effect of surface roughness on pressure drop in pipe flow.
Analysis
In turbulent flow, tubes with rough surfaces have much higher friction factors than the tubes with smooth
surfaces, and thus surface roughness leads to a much larger pressure drop in turbulent pipe flow. In the case of
laminar flow, the effect of surface roughness on the friction factor and pressure drop is negligible.
Discussion
The effect of roughness on pressure drop is significant for turbulent flow, as seen in the Moody chart.
Fully Developed Flow in Pipes
8-12C
Solution
We are to discuss how the wall shear stress varies along the flow direction in a pipe.
Analysis
The wall shear stress τw remains constant along the flow direction in the fully developed region in both
laminar and turbulent flow.
Discussion
However, in the entrance region, τw starts out large, and decreases until the flow becomes fully developed.
8-13C
Solution
We are to discuss the fluid property responsible for development of a velocity boundary layer.
Analysis
The fluid viscosity is responsible for the development of the velocity boundary layer.
Discussion
You can think of it this way: As the flow moves downstream, more and more of it gets slowed down near
the wall due to friction, which is due to viscosity in the fluid.
8-14C
Solution
We are to discuss the velocity profile in fully developed pipe flow.
Analysis
direction.
In the fully developed region of flow in a circular pipe, the velocity profile does not change in the flow
Discussion
This is, in fact, the definition of fully developed – namely, the velocity profile remains of constant shape.
8-4
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-15C
Solution
We are to discuss the relationship between friction factor and pressure loss in pipe flow.
Analysis
The friction factor for flow in a tube is proportional to the pressure loss. Since the pressure loss along
the flow is directly related to the power requirements of the pump to maintain flow, the friction factor is also proportional
to the power requirements to overcome friction. The applicable relations are
m ΔPL
m ΔPL
Wpump =
Wpump =
and
ρ
ρ
Discussion
This type of pressure loss due to friction is an irreversible loss. Hence, it is always positive (positive being
defined as a pressure drop down the pipe). A negative pressure loss would violate the second law of thermodynamics.
8-16C
Solution
We are to discuss the value of shear stress at the center of a pipe.
Analysis
The shear stress at the center of a circular tube during fully developed laminar flow is zero since the
shear stress is proportional to the velocity gradient, which is zero at the tube center.
Discussion
This result is due to the axisymmetry of the velocity profile.
8-17C
Solution
We are to discuss whether the maximum shear stress in a turbulent pipe flow occurs at the wall.
Analysis
Yes, the shear stress at the surface of a tube during fully developed turbulent flow is maximum since
the shear stress is proportional to the velocity gradient, which is maximum at the tube surface.
Discussion
This result is also true for laminar flow.
8-18C
Solution
We are to discuss the change in head loss when the pipe length is doubled.
Analysis
In fully developed flow in a circular pipe with negligible entrance effects, if the length of the pipe is
doubled, the head loss also doubles (the head loss is proportional to pipe length in the fully developed region of flow).
Discussion
If entrance lengths are not negligible, the head loss in the longer pipe would be less than twice that of the
shorter pipe, since the shear stress is larger in the entrance region than in the fully developed region.
8-19C
Solution
We are to examine a claim about volume flow rate in laminar pipe flow.
Analysis
Yes, the volume flow rate in a circular pipe with laminar flow can be determined by measuring the velocity
at the centerline in the fully developed region, multiplying it by the cross-sectional area, and dividing the result by 2. This
works for fully developed laminar pipe flow in round pipes since V = Vavg Ac = (V max / 2) Ac .
Discussion
This is not true for turbulent flow, so one must be careful that the flow is laminar before trusting this
measurement. It is also not true if the pipe is not round, even if the flow is fully developed and laminar.
8-5
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-20C
Solution
We are to examine a claim about volume flow rate in laminar pipe flow.
Analysis
No, the average velocity in a circular pipe in fully developed laminar flow cannot be determined by simply
measuring the velocity at R/2 (midway between the wall surface and the centerline). The average velocity is Vmax/2, but the
velocity at R/2 is
⎛
3V
r2 ⎞
= max , which is much larger than Vmax/2.
V ( R / 2) = V max ⎜⎜1 − 2 ⎟⎟
4
R
⎝
⎠ r =R / 2
Discussion
There is, of course, a radial location in the pipe at which the local velocity is equal to the average velocity.
Can you find that location?
8-21C
Solution
Analysis
We are to compare the head loss when the pipe diameter is halved.
In fully developed laminar flow in a circular pipe, the head loss is given by
2
2
2
64 L V
64 L V
64ν L V
LV
=
=
=
hL = f
D 2 g Re D 2 g V D / ν D 2 g
D D 2g
The average velocity can be expressed in terms of the flow rate as V =
V
V
. Substituting,
=
Ac πD 2 / 4
⎛ V ⎞ 64ν 4 LV
128νLV
⎜
⎟
⎜ πD 2 / 4 ⎟ = D 2 2 gπD 2 = gπD 4
⎝
⎠
Therefore, at constant flow rate and pipe length, the head loss is inversely proportional to the 4th power of diameter, and
thus reducing the pipe diameter by half increases the head loss by a factor of 16.
hL =
64ν L
D 2 2g
Discussion
This is a very significant increase in head loss, and shows why larger diameter tubes lead to much smaller
pumping power requirements.
8-22C
Solution
We are to discuss why the friction factor is higher in turbulent pipe flow compared to laminar pipe flow.
Analysis
In turbulent flow, it is the turbulent eddies due to enhanced mixing that cause the friction factor to be
larger. This turbulent mixing leads to a much larger wall shear stress, which translates into larger friction factor.
Discussion
Another way to think of it is that the turbulent eddies cause the turbulent velocity profile to be much fuller
(closer to uniform flow) than the laminar velocity profile.
8-23C
Solution
We are to define and discuss turbulent viscosity.
Analysis
Turbulent viscosity μt is caused by turbulent eddies, and it accounts for momentum transport by
turbulent eddies. It is expressed as τ t = − ρ u ′v ′ = μ t
∂u
where u is the mean value of velocity in the flow direction and
∂y
u ′ and u ′ are the fluctuating components of velocity.
Discussion
Turbulent viscosity is a derived, or non-physical quantity. Unlike the viscosity, it is not a property of the
fluid; rather, it is a property of the flow.
8-6
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-24C
Solution
We are to discuss the dimensions of a constant in a head loss expression.
Analysis
We compare the dimensions of the two sides of the equation h L = 0.0826 fL
V 2
D5
. Using curly brackets to
mean “the dimensions of”, we have {L} = {0.0826} ⋅ {1}{L} ⋅ {L3 t −1} ⋅ {L−5 } , and the dimensions of the constant are thus
2
{0.0826} = {L−1t 2 } .
Therefore, the constant 0.0826 is not dimensionless. This is not a dimensionally homogeneous
equation, and it cannot be used in any consistent set of units.
Discussion
Engineers often create dimensionally inhomogeneous equations like this. While they are useful for
practicing engineers, they are valid only when the proper units are used for each variable, and this can occasionally lead to
mistakes. For this reason, the present authors do not encourage their use.
8-25C
Solution
We are to discuss the change in head loss due to a decrease in viscosity by a factor of two.
In fully developed laminar flow in a circular pipe, the pressure loss and the head loss are given by
ΔP
32 μLV
32 μLV
ΔPL =
and
hL = L =
2
ρg
D
ρgD 2
When the flow rate and thus the average velocity are held constant, the head loss becomes proportional to viscosity.
Therefore, the head loss is reduced by half when the viscosity of the fluid is reduced by half.
Analysis
Discussion
This result is not valid for turbulent flow – only for laminar flow. It is also not valid for laminar flow in
situations where the entrance length effects are not negligible.
8-26C
Solution
We are to discuss the relationship between head loss and pressure drop in pipe flow.
Analysis
The head loss is related to pressure loss by h L = ΔPL / ρg . For a given fluid, the head loss can be converted
to pressure loss by multiplying the head loss by the acceleration of gravity and the density of the fluid. Thus, for constant
density, head loss and pressure drop are linearly proportional to each other.
Discussion
This result is true for both laminar and turbulent pipe flow.
8-27C
Solution
We are to discuss if the friction factor is zero for laminar pipe flow with a perfectly smooth surface.
Analysis
During laminar flow of air in a circular pipe with perfectly smooth surfaces, the friction factor is not zero
because of the no-slip boundary condition, which must hold even for perfectly smooth surfaces.
Discussion
If we compare the friction factor for rough and smooth surfaces, roughness has no effect on friction factor
for fully developed laminar pipe flow unless the roughness height is very large. For turbulent pipe flow, however,
roughness very strongly impacts the friction factor.
8-28C
Solution
We are to explain why friction factor is independent of Re at very large Re.
Analysis
At very large Reynolds numbers, the flow is fully rough and the friction factor is independent of the
Reynolds number. This is because the thickness of viscous sublayer decreases with increasing Reynolds number, and it
be comes so thin that the surface roughness protrudes into the flow. The viscous effects in this case are produced in the
main flow primarily by the protruding roughness elements, and the contribution of the viscous sublayer is negligible.
Discussion
This effect is clearly seen in the Moody chart – at large Re, the curves flatten out horizontally.
8-7
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-29E
Solution
The pressure readings across a pipe are given. The flow rates are to be determined for three different
orientations of horizontal, uphill, and downhill flow.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The flow is laminar (to be verified). 4 The pipe involves no components such as bends, valves, and
connectors. 5 The piping section involves no work devices such as pumps and turbines.
Properties
respectively.
The density and dynamic viscosity of oil are given to be ρ = 56.8 lbm/ft3 and μ = 0.0278 lbm/ft⋅s,
Analysis
The pressure drop across the pipe and the cross-sectional area of the pipe are
ΔP = P1 − P2 = 120 − 14 = 106 psi
Ac = πD 2 / 4 = π (0.5 / 12 ft) 2 / 4 = 0.001364 ft 2
Oil
D = 0.5 in
(a) The flow rate for all three cases can be determined from
L = 120 ft
(ΔP − ρgL sin θ )πD 4
V =
128μL
where θ is the angle the pipe makes with the horizontal. For the horizontal case, θ = 0 and thus sin θ = 0. Therefore,
⎛ 144 lbf/ft 2 ⎞⎛ 32.2 lbm ⋅ ft/s 2 ⎞
(106 psi)π (0.5/12 ft) 4
ΔPπD 4
⎟⎜
⎜
⎟ = 0.0109 ft 3 /s
=
Vhoriz =
⎟
128μL 128(0.0278 lbm/ft ⋅ s)(120 ft) ⎜⎝ 1 psi ⎟⎠⎜⎝
1 lbf
⎠
(b) For uphill flow with an inclination of 20°, we have θ = +20°, and
1 psi ⎞⎛
1 lbf
⎞
⎟⎜
⎟ = 16.2 psi
2
2
144
lbf/ft
32
.
2
lbm
ft/s
⋅
⎠⎝
⎝
⎠
⎛
ρgL sin θ = (56.8 lbm/ft 3 )(32.2 ft/s 2 )(120 ft ) sin 20°⎜
( ΔP − ρgL sin θ )πD 4
=
Vuphill =
128μL
=
20°
(106 − 16.2 psi)π (0.5/12 ft) ⎛⎜ 144 lbf/ft
128(0.0278 lbm/ft ⋅ s)(120 ft) ⎜⎝ 1 psi
4
2
⎞⎛ 32.2 lbm ⋅ ft/s
⎟⎜
⎟⎜
1 lbf
⎠⎝
2
⎞
⎟ = 0.00923 ft 3 /s
⎟
⎠
(c) For downhill flow with an inclination of 20°, we have θ = -20°, and
(ΔP − ρgL sin θ )πD
Vdownhill =
128μL
20°
4
⎛ 144 lbf/ft 2 ⎞⎛ 32.2 lbm ⋅ ft/s 2 ⎞
⎜
⎟⎜
⎟ = 0.0126 ft 3 /s
⎜ 1 psi ⎟⎜
⎟
1
lbf
⎝
⎠⎝
⎠
The flow rate is the highest for downhill flow case, as expected. The average fluid velocity and the Reynolds number in this
case are
0.0126 ft 3 /s
V
=
= 9.24 ft/s
V=
Ac 0.001364 ft 2
=
[106 − (−16.2) psi]π (0.5/12 ft) 4
128(0.0278 lbm/ft ⋅ s)(120 ft)
Re =
ρVD (56.8 lbm/ft 3 )(9.24 ft/s)(0.5/12 ft)
=
= 787
0.0278 lbm/ft ⋅ s
μ
which is less than 2300. Therefore, the flow is laminar for all three cases, and the analysis above is valid.
Discussion
Note that the flow is driven by the combined effect of pressure difference and gravity. As can be seen from
the calculated rates above, gravity opposes uphill flow, but helps downhill flow. Gravity has no effect on the flow rate in
the horizontal case. Downhill flow can occur even in the absence of an applied pressure difference.
8-8
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-30
Solution
Oil is being discharged by a horizontal pipe from a storage tank open to the atmosphere. The flow rate of oil
through the pipe is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The entrance and exit loses are negligible. 4 The flow is laminar (to be verified). 5 The pipe involves no
components such as bends, valves, and connectors. 6 The piping section involves no work devices such as pumps and
turbines.
Properties
The density and kinematic viscosity of oil are given to be ρ = 850 kg/m3 and ν = 0.00062 m2/s, respectively.
The dynamic viscosity is calculated to be
μ = ρν = (850 kg/m 3 )(0.00062 m 2 / s ) = 0.527 kg/m ⋅ s
Analysis
The pressure at the bottom of the tank is
P1,gage = ρgh
⎛
1 kN
= (850 kg/m )(9.81 m/s )(3 m )⎜⎜
1000
kg ⋅ m/s 2
⎝
3
2
Oil
tank
⎞
⎟
⎟
⎠
3m
5 mm
= 25.02 kN/m 2
Disregarding inlet and outlet losses, the pressure drop across the pipe is
ΔP = P1 − P2 = P1 − Patm = P1,gage = 25.02 kN/m 2 = 25.02 kPa
The flow rate through a horizontal pipe in laminar flow is determined from
2
ΔPπ D 4 ( 25.02 kN/m ) π ( 0.005 m ) ⎛ 1000 kg ⋅ m/s 2
Vhoriz =
=
⎜
128μ L
128 ( 0.527 kg/m ⋅ s )( 40 m ) ⎝
1 kN
The average fluid velocity and the Reynolds number in this case are
4
V=
⎞
3
−8
−8
3
⎟ = 1.821× 10 m /s ≅ 1.82 × 10 m /s
⎠
V
V
1.821× 10 −8 m 3 /s
=
=
= 9.27 × 10 − 4 m/s
Ac πD 2 / 4
π (0.005 m) 2 / 4
Re =
ρVD (850 kg/m 3 )(9.27 × 10 − 4 m/s)(0.005 m)
= 0.0075
=
μ
0.527 kg/m ⋅ s
which is less than 2300. Therefore, the flow is laminar and the analysis above is valid.
Discussion
The flow rate will be even less when the inlet and outlet losses are considered, especially when the inlet is
not well-rounded.
8-9
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-31
Solution
The average flow velocity in a pipe is given. The pressure drop, the head loss, and the pumping power are
to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The pipe involves no components such as bends, valves, and connectors. 4 The piping section involves no
work devices such as pumps and turbines.
Properties
respectively.
The density and dynamic viscosity of water are given to be ρ = 999.7 kg/m3 and μ = 1.307×10-3 kg/m⋅s,
Analysis
(a) First we need to determine the flow regime. The Reynolds number of the flow is
Re =
ρVD (999.7 kg/m 3 )(1.2 m/s)(2 × 10 -3 m)
= 1836
=
μ
1.307 × 10 -3 kg/m ⋅ s
Water
which is less than 2300. Therefore, the flow is laminar. Then the
friction factor and the pressure drop become
64
64
f =
=
= 0.0349
Re 1836
2
L ρV
15 m (999.7 kg/m 3 )(1.2 m/s) 2
ΔP = ΔPL = f
= 0.0349
D 2
0.002 m
2
D = 0.2 cm
1.2 m/s
L = 15 m
⎞⎛ 1 kPa ⎞
⎛
1 kN
⎟⎟⎜
⎜⎜
⎟ = 188 kPa
2
⎝ 1000 kg ⋅ m/s ⎠⎝ 1 kN/m ⎠
(b) The head loss in the pipe is determined from
ΔPL
(1.2 m/s) 2
L V2
15 m
= f
= 0.0349
= 19.2 m
hL =
D 2g
ρg
0.002 m 2(9.81 m/s 2 )
(c) The volume flow rate and the pumping power requirements are
V = VAc = V (πD 2 / 4) = (1.2 m/s)[π (0.002 m) 2 / 4] = 3.77 × 10 −6 m 3 / s
⎛ 1000 W ⎞
W pump = VΔP = (3.77 × 10 −6 m 3 / s)(188 kPa )⎜
⎟ = 0.71 W
⎝ 1 kPa ⋅ m 3 /s ⎠
Therefore, power input in the amount of 0.71 W is needed to overcome the frictional losses in the flow due to viscosity.
If the flow were instead turbulent, the pumping power would be much greater since the head loss in the pipe
Discussion
would be much greater.
8-10
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-32
Solution
The flow rate through a specified water pipe is given. The pressure drop, the head loss, and the pumping
power requirements are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The pipe involves no components such as bends, valves, and connectors. 4 The piping section involves no
work devices such as pumps and turbines.
Properties
The density and dynamic viscosity of water are given to be ρ = 999.1 kg/m3 and μ = 1.138×10-3 kg/m⋅s,
respectively. The roughness of stainless steel is 0.002 mm.
Analysis
First we calculate the average velocity and the Reynolds number to determine the flow regime:
V
V
0.008 m 3 / s
V=
=
=
= 6.366 m / s
2
Ac πD / 4 π (0.04 m) 2 / 4
ρVD (999.1 kg/m 3 )(6.366 m/s)(0.04 m)
Re =
=
= 2.236 × 10 5
μ
1.138 × 10 −3 kg/m ⋅ s
Water
D = 4 cm
8 L/s
which is greater than 4000. Therefore, the flow is turbulent. The
relative roughness of the pipe is
2 × 10 −6 m
ε/D=
= 5 × 10 −5
0.04 m
The friction factor can be determined from the Moody chart, but to avoid the reading error, we
Colebrook equation using an equation solver (or an iterative scheme),
⎛ε / D
⎛ 5 × 10 −5
1
2.51
1
2.51 ⎞⎟
= −2.0 log⎜
+
→
= −2.0 log⎜
+
⎜
⎜
⎟
f
f
2.236 × 10 5 f
⎝ 3.7 Re f ⎠
⎝ 3.7
It gives f = 0.01573. Then the pressure drop, head loss, and the required power input become
ΔP = ΔPL = f
hL =
30 m (999.1 kg/m 3 )(6.366 m/s) 2
L ρV 2
= 0.01573
0.04 m
2
D 2
L = 30 m
determine it from the
⎞
⎟
⎟
⎠
⎛
⎞⎛ 1 kPa ⎞
1 kN
⎜⎜
⎟⎟⎜
= 239 kPa
2 ⎟
⎝ 1000 kg ⋅ m/s ⎠⎝ 1 kN/m ⎠
ΔPL
30 m (6.366 m/s) 2
L V2
= f
= 0.01573
= 24.4 m
ρg
0.04 m 2(9.81 m/s 2 )
D 2g
⎛ 1 kW
⎞
W pump = VΔP = (0.008 m 3 / s )(239 kPa )⎜
⎟ = 1.91 kW
3
⎝ 1 kPa ⋅ m /s ⎠
Therefore, useful power input in the amount of 1.91 kW is needed to overcome the frictional losses in the pipe.
Discussion
The friction factor could also be determined easily from the explicit Haaland relation. It would give f =
0.0155, which is sufficiently close to 0.0157. Also, the friction factor corresponding to ε = 0 in this case is 0.0153, which
indicates that stainless steel pipes in this case can be assumed to be smooth with an error of about 2%. Also, the power
input determined is the mechanical power that needs to be imparted to the fluid. The shaft power will be more than this due
to pump inefficiency; the electrical power input will be even more due to motor inefficiency.
8-11
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-33E
Solution
determined.
The flow rate and the head loss in an air duct is given. The minimum diameter of the duct is to be
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The duct involves no components such as bends, valves, and connectors. 4 Air is an ideal gas. 5 The duct is
smooth since it is made of plastic, ε ≈ 0. 6 The flow is turbulent (to be verified).
Properties
The density, dynamic viscosity, and kinematic viscosity of air at 100°F are ρ = 0.07088 lbm/ft3, μ =
0.04615 lbm/ft⋅h, and ν = 0.6512 ft2/s = 1.809×10-4 ft2/s.
Analysis
The average velocity, Reynolds number, friction factor, and the head loss relations can be expressed as (D is
in ft, V is in ft/s, Re and f are dimensionless)
V
V
12 ft 3 / s
=
=
2
Ac πD / 4 πD 2 / 4
VD
VD
=
Re =
ν
1.809 × 10 − 4 ft 2 / s
V=
Air
D
12 ft3/s
⎛ 2.51 ⎞
⎛ε / D
2.51 ⎞⎟
⎟
= −2.0 log⎜
= −2.0 log⎜
+
⎟
⎟
⎜
⎜
3
.
7
Re f ⎠
f
⎝ Re f ⎠
⎝
L V2
L V2
V2
400 ft
hL = f
→ 50 = f
= f
D 2g
D 2g
D 2(32.2 ft/s 2 )
This is a set of 4 equations in 4 unknowns, and solving them with an equation solver gives
1
D = 0.88 ft,
L = 400 ft
f = 0.0181, V = 19.8 ft/s, and Re = 96,040
Therefore, the diameter of the duct should be more than 0.88 ft if the head loss is not to exceed 50 ft. Note that Re > 4000,
and thus the turbulent flow assumption is verified.
The diameter can also be determined directly from the third Swamee-Jain formula to be
⎡
⎛ LV 2
D = 0.66 ⎢ε 1.25 ⎜⎜
⎢
⎝ gh L
⎣
⎞
⎟
⎟
⎠
4.75
⎛ L
+ νV 9.4 ⎜⎜
⎝ gh L
⎞
⎟⎟
⎠
5.2 ⎤ 0.04
⎥
⎥
⎦
5.2
⎡
⎞ ⎤
⎛
400 ft
⎟ ⎥
= 0.66 ⎢0 + (0.180 × 10 −3 ft 2 / s )(12 ft 3 / s ) 9.4 ⎜⎜
2
⎟
⎢
⎝ (32.2 ft/s )(50 ft) ⎠ ⎥⎦
⎣
= 0.89 ft
0.04
Note that the difference between the two results is less than 2%. Therefore, the simple Swamee-Jain relation
Discussion
can be used with confidence.
8-12
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-34
Solution
In fully developed laminar flow in a circular pipe, the velocity at r = R/2 is measured. The velocity at the
center of the pipe (r = 0) is to be determined.
Assumptions
The flow is steady, laminar, and fully developed.
The velocity profile in fully developed laminar flow in a circular pipe is given by
⎛
r2 ⎞
u (r ) = u max ⎜⎜1 − 2 ⎟⎟
⎝ R ⎠
where umax is the maximum velocity which occurs at pipe center, r = 0. At r =R/2,
⎛ ( R / 2) 2 ⎞
3u
1
⎟ = u max ⎛⎜1 − ⎞⎟ = max
u ( R / 2) = u max ⎜⎜1 −
2
⎟
4
⎝ 4⎠
R
⎠
⎝
Analysis
u(r) = umax(1-r2/R2)
R
r
Solving for umax and substituting,
4u ( R / 2 ) 4 ( 6 m/s )
umax =
=
= 8.00 m/s
3
3
which is the velocity at the pipe center.
0
umax
Discussion
The relationship used here is valid only for fully developed laminar flow. The result would be much
different if the flow were turbulent.
8-35
Solution
The velocity profile in fully developed laminar flow in a circular pipe is given. The average and maximum
velocities as well as the flow rate are to be determined.
Assumptions
The flow is steady, laminar, and fully developed.
The velocity profile in fully developed laminar flow in a circular pipe is given by
⎛
r2 ⎞
u (r ) = u max ⎜⎜1 − 2 ⎟⎟
⎝ R ⎠
The velocity profile in this case is given by
Analysis
u (r ) = 4(1 − r 2 / R 2 )
u(r) = umax(1-r2/R2)
R
r
Comparing the two relations above gives the maximum velocity to be
umax = 4.00 m/s. Then the average velocity and volume flow rate
become
u
4 m/s
Vavg = max =
= 2.00 m/s
2
2
0
umax
V = V avg Ac = V avg (πR 2 ) = (2 m/s)[π (0.02 m) 2 ] = 0.00251 m 3 /s
Discussion
A unique feature of fully developed laminar pipe flow is that the maximum velocity is exactly twice the
average velocity. This is not the case for turbulent pipe flow, since the velocity profile is much fuller.
8-13
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-36
Solution
The velocity profile in fully developed laminar flow in a circular pipe is given. The average and maximum
velocities as well as the flow rate are to be determined.
Assumptions
Analysis
The flow is steady, laminar, and fully developed.
The velocity profile in fully developed laminar flow in a circular pipe is given by
⎛
r2 ⎞
u (r ) = u max ⎜⎜1 − 2 ⎟⎟
⎝ R ⎠
The velocity profile in this case is given by
u(r) = umax(1-r2/R2)
R
u (r ) = 4(1 − r / R )
2
2
r
Comparing the two relations above gives the maximum velocity to be umax
= 4.00 m/s. Then the average velocity and volume flow rate become
u
4 m/s
Vavg = max =
= 2.00 m/s
2
2
V = V A = V (πR 2 ) = (2 m/s)[π (0.07 m) 2 ] = 0.0308 m 3 /s
avg
c
0
umax
avg
Discussion
Compared to the previous problem, the average velocity remains the same since the maximum velocity (at
the centerline) remains the same, but the volume flow rate increases as the diameter increases.
8-37
Solution
Air enters the constant spacing between the glass cover and the plate of a solar collector. The pressure drop
of air in the collector is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The roughness effects are negligible, and thus the inner surfaces are considered to be smooth, ε ≈ 0. 4 Air is an
ideal gas. 5 The local atmospheric pressure is 1 atm.
Properties
The properties of air at 1 atm and 45° are ρ = 1.109 kg/m3, μ = 1.941×10-5 kg/m⋅s, and ν = 1.750×10-5 m2/s.
Analysis
Mass flow rate, cross-sectional area, hydraulic diameter, average velocity, and the Reynolds number are
m = ρV = (1.11 kg/m 3 )(0.15 m 3 /s ) = 0.1665 kg/s
Ac = a × b = (1 m)(0.03 m) = 0.03 m 2
Glass cover
Air
0.15 m3/s
5m
4 Ac
4(0.03 m 2 )
=
= 0.05825 m
2(1 + 0.03) m
p
V
0.15 m 3 / s
=
=5m/ s
V=
Ac
0.03 m 2
Collector plate
VD h (5 m/s)(0.05825 m)
Insulation
Re =
=
= 1.664 × 10 4
2
−5
υ
1.750 × 10 m /s
Since Re is greater than 4000, the flow is turbulent. The friction factor corresponding to this Reynolds number for a smooth
flow section (ε/D = 0) can be obtained from the Moody chart. But to avoid reading error, we use the Colebrook equation,
Dh =
⎛ε / D
2.51
= −2.0 log⎜
+
⎜
f
⎝ 3.7 Re f
which gives f = 0.0271. Then the pressure drop becomes
1
ΔP = ΔPL = f
⎞
⎟ →
⎟
⎠
⎛
2.51 ⎞⎟
= −2.0 log⎜ 0 +
⎜
f
16,640 f ⎟⎠
⎝
1
(1.11 kg/m 3 )(5 m/s) 2
L ρV 2
5m
= 0.0271
D 2
0.05825 m
2
⎛
1N
⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞⎛ 1 Pa ⎞
⎟⎜
= 32.3 Pa
⎟⎝ 1 N/m 2 ⎟⎠
⎠
Discussion
The friction factor could also be determined easily from the explicit Haaland relation. It would give f =
0.0270, which is sufficiently close to 0.0271.
8-14
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-38
Solution
Oil flows through a pipeline that passes through icy waters of a lake. The pumping power needed to
overcome pressure losses is to be determined.
Assumptions The flow is steady and incompressible. 2 The flow section considered is away from the entrance, and thus
the flow is fully developed. 3 The roughness effects are negligible, and thus the inner surfaces are considered to be smooth,
ε ≈ 0.
Properties
The properties of oil are given to be ρ = 894 kg/m3 and μ = 2.33 kg/m⋅s.
Analysis
The volume flow rate and the Reynolds number in this case are
π (0.4 m) 2
πD 2
V = VAc = V
= (0.5 m/s)
= 0.0628 m 3 /s
4
4
(Icy lake, 0°C)
Oil
10°C
0.5 m/s
ρVD (894 kg/m 3 )(0.5 m/s)(0.4 m)
Re =
=
= 76.7
μ
2.33 kg/m ⋅ s
D = 0.4 m
L = 300 m
which is less than 2300. Therefore, the flow is laminar, and the friction factor is
64
64
f =
=
= 0.834
Re 76.7
Then the pressure drop in the pipe and the required pumping power become
ΔP = ΔPL = f
300 m (894 kg/m 3 )(0.5 m/s) 2
L ρV 2
= 0.834
0.4 m
2
D 2
⎛
⎞⎛ 1 kPa ⎞
1 kN
⎜⎜
⎟⎟⎜
⎟ = 69.9 kPa
2
1000
kg
m/s
⋅
⎝
⎠⎝ 1 kN/m ⎠
⎞
⎛ 1 kW
W pump = VΔP = (0.0628 m 3 /s)(69.9 kPa )⎜
⎟ = 4.39 kW
3
⎝ 1 kPa ⋅ m /s ⎠
Discussion
The power input determined is the mechanical power that needs to be imparted to the fluid. The shaft power
will be much more than this due to pump inefficiency; the electrical power input will be even more due to motor
inefficiency.
8-39
Solution
Laminar flow through a square channel is considered. The change in the head loss is to be determined when
the average velocity is doubled.
Assumptions
developed.
Analysis
1 The flow remains laminar at all times. 2 The entrance effects are negligible, and thus the flow is fully
The friction factor for fully developed laminar flow in a square channel is
ρVD
56.92
where Re =
f =
Re
μ
V
Then the head loss for laminar flow can be expressed as
h L ,1 = f
μL
L V 2 56.92 L V 2 56.92μ L V 2
=
=
= 28.46V
ρVD D 2 g
Re D 2 g
D 2g
ρgD 2
which shows that the head loss is proportional to the average velocity. Therefore, the head loss doubles when the average
velocity is doubled. This can also be shown as
hL ,2 = 28.46V2
Discussion
⎛
μL
μL
μL ⎞
⎜
⎟ = 2hL ,1
2 = 28.46( 2V )
2 = 2⎜ 28.46V
ρgD
ρgD
ρgD 2 ⎟⎠
⎝
The conclusion above is also valid for laminar flow in channels of different cross-sections.
8-15
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-40
Solution
Turbulent flow through a smooth pipe is considered. The change in the head loss is to be determined when
the average velocity is doubled.
Assumptions 1 The flow remains turbulent at all times. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The inner surface of the pipe is smooth.
Analysis
The friction factor for the turbulent flow in smooth pipes is given as
ρVD
f = 0.184 Re −0.2 where Re =
μ
Then the head loss of the fluid for turbulent flow can be expressed as
h L ,1 = f
⎛ ρVD ⎞
L V2
L V2
⎟⎟
= 0.184 Re − 0.2
= 0.184⎜⎜
D 2g
D 2g
⎝ μ ⎠
−0.2
⎛ ρD ⎞
L V2
⎟⎟
= 0.184⎜⎜
D 2g
⎝ μ ⎠
−0.2
L V 1.8
D 2g
which shows that the head loss is proportional to the 1.8th power of the average velocity. Therefore, the head loss increases
by a factor of 21.8 = 3.48 when the average velocity is doubled. This can also be shown as
−0.2
−0.2
⎛ ρD ⎞
⎛ ρD ⎞
L V21.8
L (2V )1.8
⎟⎟
⎟⎟
= 0.184⎜⎜
hL ,2 = 0.184⎜⎜
D 2g
D 2g
⎝ μ ⎠
⎝ μ ⎠
0
.
2
−
⎡
⎛ ρD ⎞
L V 1.8 ⎤
⎟⎟
⎥ = 21.8 hL ,1 = 3.48hL ,1
= 21.8 ⎢0.184⎜⎜
D 2g ⎥
⎢⎣
⎝ μ ⎠
⎦
For fully rough flow in a rough pipe, the friction factor is independent of the Reynolds
number and thus the flow velocity. Therefore, the head loss increases by a factor of 4
in this case since
V
L V2
D 2g
and thus the head loss is proportional to the square of the average velocity when f, L, and D are constant.
h L ,1 = f
Discussion
Most flows in practice are in the fully rough regime, and thus the head loss is generally assumed to be
proportional to the square of the average velocity for all kinds of turbulent flow. Note that we use diameter D here in place
of hydraulic diameter Dh. For a square duct, it turns out that Dh = D, so this is a valid approximation.
8-16
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-41
Solution
Air enters a rectangular duct. The fan power needed to overcome the pressure losses is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 Air is an ideal gas. 4 The duct involves no components such as bends, valves, and connectors. 5 The flow
section involves no work devices such as fans or turbines
Properties
The properties of air at 1 atm and 35°C are ρ = 1.145 kg/m3, μ = 1.895×10-5 kg/m⋅s, and ν = 1.655×10-5
2
m /s. The roughness of commercial steel surfaces is ε = 0.000045 m.
Analysis
The hydraulic diameter, the volume flow rate, and the Reynolds number in this case are
4 Ac
4(0.15 m)(0.20 m)
4ab
Dh =
=
=
= 0.1714 m
7m
p
2(a + b)
2(0.15 + 0.20) m
V = VA = V (a × b) = (7 m/s)(0.15 × 0.20 m 2 ) = 0.21 m 3 /s
c
Re =
ρVD h (1.145 kg/m 3 )(7 m/s)(0.1714 m)
=
= 72,490
μ
1.895 × 10 −5 kg/m ⋅ s
which is greater than 4000. Therefore, the flow is turbulent. The relative
roughness of the pipe is
15 cm
Air
7 m/s
20 cm
4.5 × 10 −5 m
= 2.625 × 10 − 4
ε / Dh =
0.1714 m
The friction factor can be determined from the Moody chart, but to avoid the reading error, we determine it from the
Colebrook equation using an equation solver (or an iterative scheme),
⎛ 2.625 × 10 −4
⎛ ε / Dh
1
2.51 ⎞⎟
2.51 ⎞⎟
→
= −2.0 log⎜
+
= −2.0 log⎜
+
⎜
⎟
⎜
3.7
f
f
72,490 f ⎟⎠
Re f ⎠
⎝
⎝ 3.7
It gives f = 0.02034. Then the pressure drop in the duct and the required pumping power become
1
ΔP = ΔPL = f
(1.145 kg/m 3 )(7 m/s) 2
L ρV 2
7m
= 0.02034
D 2
0.1714 m
2
⎛
1N
⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞⎛ 1 Pa ⎞
⎟⎜
⎟⎝ 1 N/m 2 ⎟⎠ = 23.3 Pa
⎠
⎛ 1W ⎞
Wpump = V ΔP = ( 0.21 m3 /s ) ( 23.3 Pa ) ⎜
⎟ = 4.90 W
3
⎝ 1 Pa ⋅ m /s ⎠
Discussion
The friction factor could also be determined easily from the explicit Haaland relation. It would give f =
0.02005, which is sufficiently close to 0.02034. Also, the power input determined is the mechanical power that needs to be
imparted to the fluid. The shaft power will be much more than this due to fan inefficiency; the electrical power input will be
even more due to motor inefficiency.
8-17
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-42E
Solution
Water passes through copper tubes at a specified rate. The pumping power required per ft length to maintain
flow is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The pipe involves no components such as bends, valves, and connectors. 4 The piping section involves no
work devices such as pumps and turbines.
Properties
The density and dynamic viscosity of water at 60°F are ρ = 62.36 lbm/ft3 and μ = 2.713 lbm/ft⋅h =
-4
7.536×10 lbm/ft⋅s. The roughness of copper tubing is 5×10-6 ft.
Analysis
First we calculate the average velocity and the Reynolds number to determine the flow regime:
m
m
1.2 lbm / s
=
=
= 6.272 ft/s
V=
2
ρAc ρ (πD / 4 ) (62.36 lbm/ft 3 )[π (0.75/12 ft) 2 / 4]
ρVD (62.36 lbm/ft 3 )(6.272 ft/s)(0.75/12 ft)
=
= 32,440
μ
7.536 × 10 − 4 lbm/ft ⋅ s
which is greater than 4000. Therefore, the flow is turbulent. The relative
roughness of the pipe is
Re =
ε/D=
Water
D = 0.75 in
1.2 lbm/s
5 × 10 −6 ft
= 8 × 10 −5
0.75 / 12 ft
The friction factor can be determined from the Moody chart, but to avoid the reading error, we determine it from the
Colebrook equation using an equation solver (or an iterative scheme),
⎛ε / D
2.51
= −2.0 log⎜
+
⎜
f
⎝ 3.7 Re f
1
⎞
⎟ →
⎟
⎠
⎛ 8 × 10 −5
2.51 ⎞⎟
= −2.0 log⎜
+
⎜
f
32,440 f ⎟⎠
⎝ 3.7
1
It gives f = 0.02328. Then the pressure drop and the required power input become
ΔP = ΔPL = f
(62.36 lbm/ft 3 )(6.272 ft/s) 2 ⎛
L ρV 2
1 ft
1 lbf
⎞
2
= 0.02328
⎜
⎟ = 14.2 lbf/ft
D 2
0.75/12 ft
2
⎝ 32.2 lbm ⋅ ft/s ⎠
1W
m ΔP (1.2 lbm/s)(14.2 lbf/ft 2 ) ⎛
⎞
=
W pump = VΔP =
⎜
⎟ = 0.37 W (per ft length)
ρ
⎝ 0.737 lbf ⋅ ft/s ⎠
62.36 lbm/ft 3
Therefore, useful power input in the amount of 0.37 W is needed per ft of tube length to overcome the frictional losses in
the pipe.
Discussion
The friction factor could also be determined easily from the explicit Haaland relation. It would give f =
0.02305, which is sufficiently close to 0.02328. Also, the friction factor corresponding to ε = 0 in this case is 0.02306,
which indicates that copper pipes can be assumed to be smooth with a negligible error. Also, the power input determined is
the mechanical power that needs to be imparted to the fluid. The shaft power will be more than this due to pump
inefficiency; the electrical power input will be even more due to motor inefficiency.
8-18
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-43
Solution
The pressure of oil in a pipe which discharges into the atmosphere is measured at a certain location. The
flow rates are to be determined for 3 different orientations.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The flow is laminar (to be verified). 4 The pipe involves no components such as bends, valves, and
connectors. 5 The piping section involves no work devices such as pumps and turbines.
Properties
The density and dynamic viscosity of oil are given to be ρ = 876 kg/m3 and μ = 0.24 kg/m⋅s.
Analysis
The pressure drop across the pipe and the cross-sectional area are
ΔP = P1 − P2 = 135 − 88 = 47 kPa
Ac = πD 2 / 4 = π (0.015 m) 2 / 4 = 1.767 × 10 − 4 m 2
135 kPa
(a) The flow rate for all three cases can be determined from,
(ΔP − ρgL sin θ )πD 4
V =
128μL
where θ is the angle the pipe makes with the horizontal. For the horizontal
case, θ = 0 and thus sin θ = 0. Therefore,
(47 kPa)π (0.015 m) 4 ⎛⎜ 1 kg ⋅ m/s 2
ΔPπD 4
=
Vhoriz =
128μL 128(0.24 kg/m ⋅ s)(15 m) ⎜⎝ 1 N
⎞⎛ 1000 N/m 2
⎟⎜
⎟⎜ 1 kPa
⎠⎝
Oil
L = 15 m
D = 1.5 cm
⎞
⎟ = 1.62 × 10 −5 m 3 /s
⎟
⎠
(b) For uphill flow with an inclination of 8°, we have θ = +8°, and
(ΔP − ρgL sin θ )πD 4
Vuphill =
128μL
=
[(47,000 Pa − (876 kg/m 3 )(9.81 m/s 2 )(15 m) sin 8°]π (0.015 m) 4
128(0.24 kg/m ⋅ s)(15 m)
⎛ 1 kg ⋅ m/s 2
⎜
⎜ 1 Pa ⋅ m 2
⎝
⎞
⎟
⎟
⎠
= 1.00 × 10 −5 m 3 /s
(c) For downhill flow with an inclination of 8°, we have θ = -8°, and
(ΔP − ρgL sin θ )πD 4
Vdownhill =
128μL
=
[(47,000 Pa − (876 kg/m 3 )(9.81 m/s 2 )(15 m) sin( −8°)]π (0.015 m) 4
128(0.24 kg/m ⋅ s)(15 m)
⎛ 1 kg ⋅ m/s 2
⎜
⎜ 1 Pa ⋅ m 2
⎝
⎞
⎟
⎟
⎠
= 2.24 × 10 −5 m 3 /s
The flow rate is the highest for downhill flow case, as expected. The average fluid velocity and the Reynolds number in this
case are
V=
2.24 × 10 −5 .m 3 /s
V
=
= 0.127 m/s
Ac 1.767 × 10 - 4 m 2
Re =
ρVD (876 kg/m 3 )(0.127 m/s)(0.015 m)
=
= 7. 0
0.24 kg/m ⋅ s
μ
which is less than 2300. Therefore, the flow is laminar for all three cases, and the analysis above is valid.
Discussion
Note that the flow is driven by the combined effect of pressure difference and gravity. As can be seen from
the calculated rates above, gravity opposes uphill flow, but helps downhill flow. Gravity has no effect on the flow rate in
the horizontal case.
8-19
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-44
Solution
Glycerin is flowing through a horizontal pipe which discharges into the atmosphere at a specified flow rate.
The absolute pressure at a specified location in the pipe, and the angle θ that the pipe must be inclined downwards for the
pressure in the entire pipe to be atmospheric pressure are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The flow is laminar (to be verified). 4 The pipe involves no components such as bends, valves, and
connectors. 5 The piping section involves no work devices such as pumps and turbines.
Properties
The density and dynamic viscosity of glycerin at 40°C are given to be ρ = 1252 kg/m3 and μ = 0.27 kg/m⋅s.
Analysis
(a) The flow rate for horizontal or inclined pipe can be determined from
(ΔP − ρgL sin θ )πD 4
V =
(1)
128μL
where θ is the angle the pipe makes with the horizontal. For the
horizontal case, θ = 0 and thus sin θ = 0. Therefore,
ΔPπD 4
Vhoriz =
128μL
Solving for ΔP and substituting,
ΔP =
128μLVhoriz
πD
4
=
Glycerin
D = 2 cm
0.035 L/s
L = 25 m
(2)
128(0.27 kg/m ⋅ s)(25 m)(0.035 × 10 -3 m 3 /s) ⎛⎜
1 kN
4
2
⎜
π (0.02 m)
⎝ 1000 kg ⋅ m/s
⎞
⎟
⎟
⎠
= 60.2 kN/m 2 = 60.2 kPa
Then the pressure 25 m before the pipe exit becomes
ΔP = P1 − P2
→
P1 = P2 + ΔP = 100 + 60.2 = 160.2 kPa
(b) When the flow is gravity driven downhill with an inclination θ, and the pressure in the entire pipe is constant at the
atmospheric pressure, the hydrostatic pressure rise with depth is equal to pressure drop along the pipe due to frictional
effects. Setting ΔP = P1 – P2 = 0 in Eq. (1) and substituting, θ is determined to be
ρg sin θπD 4
Vdownhill =
128μ
0.035 × 10 −3 m 3 /s =
− (1252 kg/m 3 )(9.81 m/s 2 ) sin θπ (0.02 m) 4
128(0.27 kg/m ⋅ s)
→
θ = −11.3°
Therefore, the pipe must be inclined 11.3° downwards from the horizontal to maintain flow in the pipe at the same rate.
Verification: The average fluid velocity and the Reynolds number in this case are
V=
0.035 × 10 −3 m 3 /s
V
V
=
=
= 0.111 m/s
Ac πD 2 / 4
π (0.02 m) 2 / 4
Re =
ρVD (1252 kg/m 3 )(0.111 m/s)(0.02 m)
=
= 10.3
μ
0.27 kg/m ⋅ s
which is less than 2300. Therefore, the flow is laminar, as assumed, and the analysis above is valid.
Discussion
Note that the flow is driven by the combined effect of pressure difference and gravity. Gravity has no effect
on the flow rate in the horizontal case, but it governs the flow alone when there is no pressure difference across the pipe.
8-20
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-45
Solution
Air in a heating system is distributed through a rectangular duct made of commercial steel at a specified
rate. The pressure drop and head loss through a section of the duct are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 Air is an ideal gas. 4 The duct involves no components such as bends, valves, and connectors. 5 The flow
section involves no work devices such as fans or turbines.
Properties
The roughness of commercial steel surfaces is ε = 0.000045 m. The dynamic viscosity of air at 40°C is μ =
1.918×10-5 kg/m⋅s, and it is independent of pressure. The density of air listed in that table is for 1 atm. The density at 105
kPa and 315 K can be determined from the ideal gas relation to be
ρ=
105 kPa
P
=
= 1.169 kg/m 3
RT (0.287 kPa ⋅ m 3 /kg.K)(40 + 273 K)
Air duct
0.2 m × 0.3 m
Analysis
The hydraulic diameter, average velocity, and
Reynolds number are
4 Ac
4(0.3 m)(0.20 m)
4ab
=
=
= 0.24 m
Dh =
2(a + b)
2(0.3 + 0.20) m
p
Air
43°C
0.5 m3/s
0.5.m 3 /s
V
V
V=
=
=
= 8.333 m/s
Ac a × b (0.3 m)(0.2 m)
Re =
L = 40
ρVDh (1.169 kg/m 3 )(8.333 m/s)(0.24 m)
=
= 121,900
μ
1.918 × 10 −5 kg/m ⋅ s
which is greater than 4000. Therefore, the flow is turbulent. The relative roughness of the duct is
4.5 × 10 −5 m
= 1.875 × 10 − 4
0.24 m
The friction factor can be determined from the Moody chart, but to avoid the reading error, we determine it from the
Colebrook equation using an equation solver (or an iterative scheme),
ε / Dh =
⎞
⎛ 1.875 × 10 −4
⎛ ε / Dh
2.51 ⎞⎟
1
2.51
⎟
→
= −2.0 log⎜
+
= −2.0 log⎜
+
⎟
⎜
⎟
⎜ 3.7
3
.
7
Re
f
f
f
121
,
900
f
⎠
⎝
⎠
⎝
It gives f = 0.01833. Then the pressure drop in the duct and the head loss become
1
ΔP = ΔPL = f
hL =
L ρV 2
40 m (1.169 kg/m 3 )(8.333 m/s) 2
= 0.01833
D 2
0.24 m
2
⎛
1N
⎜
⎜ 1 kg ⋅ m/s 2
⎝
⎞
⎟ = 124 N/m 2 = 124 Pa
⎟
⎠
ΔPL
L V2
40 m (8.333 m/s) 2
= f
= 0.01833
= 10.8 m
ρg
D 2g
0.24 m 2(9.81 m/s 2 )
Discussion
The required pumping power in this case is
⎛ 1W ⎞
W pump = VΔP = (0.5 m 3 /s)(124 Pa )⎜
⎟ = 62 W
⎝ 1 Pa ⋅ m 3 /s ⎠
Therefore, 62 W of mechanical power needs to be imparted to the fluid. The shaft power will be more than this due to fan
inefficiency; the electrical power input will be even more due to motor inefficiency. Also, the friction factor could be
determined easily from the explicit Haaland relation. It would give f = 0.0181, which is sufficiently close to 0.0183.
8-21
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-46
Solution
Glycerin is flowing through a smooth pipe with a specified average velocity. The pressure drop per 10 m of
the pipe is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The pipe involves no components such as bends, valves, and connectors. 4 The piping section involves no
work devices such as pumps and turbines.
Properties
respectively.
The density and dynamic viscosity of glycerin at 40°C are given to be ρ = 1252 kg/m3 and μ = 0.27 kg/m⋅s,
Analysis
The volume flow rate and the Reynolds number are
V = VAc = V (πD 2 / 4) = (3.5 m/s)[π (0.05 m) 2 / 4] = 0.006872 m 3 /s
Re =
ρVD h (1252 kg/m 3 )(3.5 m/s)(0.05 m)
=
= 811.5
μ
0.27 kg/m ⋅ s
Glycerin
3.5 m/s
which is less than 2300. Therefore, the flow is laminar, and the friction
factor for this circular pipe is
64
64
f =
=
= 0.07887
Re 811.5
Then the pressure drop in the pipe becomes
ΔP = ΔPL = f
L ρV 2
10 m (1252 kg/m 3 )(3.5 m/s) 2
= 0.07887
D 2
0.05 m
2
D = 5 cm
L = 10 m
⎞⎛ 1 kPa
⎛
1 kN
⎟⎟⎜
⎜⎜
2
1000
kg
m/s
⋅
⎠⎝ 1 kN/m
⎝
⎞
⎟ = 121 kPa
⎠
The required pumping power in this case is
⎛ 1 kW
⎞
W pump = VΔP = (0.006872 m 3 /s )(121 kPa )⎜
⎟ = 0.83 kW
⎝ 1 kPa ⋅ m 3 /s ⎠
Therefore, 0.83 kW of mechanical power needs to be imparted to the fluid. The shaft power will be more than this due to
pump inefficiency; the electrical power input will be even more due to motor inefficiency.
Discussion
8-22
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-47
Solution
In the previous problem, the effect of the pipe diameter on the pressure drop for the same constant flow rate
is to be investigated by varying the pipe diameter from 1 cm to 10 cm in increments of 1 cm.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
g=9.81
Vdot=3.5*pi*(0.05)^2/4
Ac=pi*D^2/4
rho= 1252
nu=mu/rho
mu=0.27
L= 10
V=Vdot/Ac
"Reynolds number"
Re=V*D/nu
f=64/Re
DP=f*(L/D)*rho*V^2/2000 "kPa"
W=Vdot*DP "kW"
D, m
ΔP, kPa
V, m/s
Re
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.1
75600
4725
933.3
295.3
121
58.33
31.49
18.46
11.52
7.56
87.5
21.88
9.722
5.469
3.5
2.431
1.786
1.367
1.08
0.875
4057
2029
1352
1014
811.5
676.2
579.6
507.2
450.8
405.7
80000
70000
60000
DP, kPa
50000
40000
30000
20000
10000
0
0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09
0.1
D, m
Discussion
The pressure drop decays quite rapidly with increasing diameter – by several orders of magnitude, in fact.
We conclude that larger diameter pipes are better when pressure drop is of concern. Of course, bigger pipes cost more and
take up more space, so there is typically an optimum pipe size that is a compromise between cost and practicality.
8-23
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-48E
Solution
Air is flowing through a square duct made of commercial steel at a specified rate. The pressure drop and
head loss per ft of duct are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 Air is an ideal gas. 4 The duct involves no components such as bends, valves, and connectors. 5 The flow
section involves no work devices such as fans or turbines.
Properties
The density and dynamic viscosity of air at 1 atm and 60°F are ρ = 0.07633 lbm/ft3, μ = 0.04365 lbm/ft⋅h,
and ν = 0.5718 ft2/s = 1.588×10-4 ft2/s. The roughness of commercial steel surfaces is ε = 0.00015 ft.
The hydraulic diameter, the average velocity, and the Reynolds number in this case are
Analysis
Dh =
4 Ac 4a 2
=
= a = 1 ft
4a
p
V
V 1200 ft 3 /min
= 2 =
= 1200 ft/min = 20 ft/s
V =
Ac a
(1 ft) 2
Re =
VD h
=
(20 ft/s)(1 ft)
Air duct
1 ft × 1 ft
= 1.259 × 10 5
Air
ν
L = 1 ft
1.588 × 10 − 4 ft 2 /s
60°F
which is greater than 4000. Therefore, the flow is turbulent.
1200 cfm
The relative roughness of the duct is
0.00015 ft
ε / Dh =
= 1.5 ×10 − 4
1 ft
The friction factor can be determined from the Moody chart, but to avoid the reading error, we determine it from the
Colebrook equation using an equation solver (or an iterative scheme),
⎞
⎛ ε / Dh
⎛ 1.5 × 10 −4
2.51 ⎞⎟
1
2.51
⎟
= −2.0 log⎜
+
→
= −2.0 log⎜
+
⎜ 3.7
⎟
⎟
⎜ 3.7
Re
f
f
f
125
,
900
f
⎝
⎠
⎠
⎝
It gives f = 0.0180. Then the pressure drop in the duct and the head loss become
1
ΔP = ΔPL = f
hL =
Discussion
1 ft (0.07633 lbm/ft 3 )(20 ft/s) 2
L ρV 2
= 0.0180
1 ft
2
D 2
1 lbf
⎛
⎞
−3
2
⎜
⎟ = 8.53 × 10 lbf/ft
32
.
2
lbm
⋅
ft/s
⎝
⎠
ΔPL
L V2
1 ft (20 ft/s) 2
= f
= 0.0180
= 0.112 ft
ρg
D 2g
1 ft 2(32.2 ft/s 2 )
The required pumping power in this case is
1W
⎞
⎛
W pump = VΔP = (1200 / 60 ft 3 /s)(8.53 ×10 −3 lbf/ft 2 )⎜
⎟ = 0.231 W (per ft length)
⎝ 0.737 lbf ⋅ ft/s ⎠
Therefore, 0.231 W of mechanical power needs to be imparted to the fluid per ft length of the duct. The shaft power will be
more than this due to fan inefficiency; the electrical power input will be even more due to motor inefficiency. Also, the
friction factor could be determined easily from the explicit Haaland relation. It would give f = 0.0178, which is sufficiently
close to 0.0180.
8-24
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-49
Solution
Liquid ammonia is flowing through a copper tube at a specified mass flow rate. The pressure drop, the head
loss, and the pumping power required to overcome the frictional losses in the tube are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The pipe involves no components such as bends, valves, and connectors. 4 The piping section involves no
work devices such as pumps and turbines.
Properties
The density and dynamic viscosity of liquid ammonia at -20°C are ρ = 665.1 kg/m3 and μ = 2.361×10-4
kg/m⋅s. The roughness of copper tubing is 1.5×10-6 m.
Analysis
First we calculate the average velocity and the Reynolds number to determine the flow regime:
0.15 kg/s
m
m
=
=
= 11.49 m/s
V=
2
ρAc ρ (πD / 4 ) (665.1 kg/m 3 )[π (0.005 m) 2 / 4]
ρVD (665.1 kg/m 3 )(11.49 m/s)(0.005 m)
=
= 1.618 × 10 5
μ
2.361× 10 − 4 kg/m ⋅ s
which is greater than 4000. Therefore, the flow is turbulent. The
relative roughness of the pipe is
Re =
Ammonia
D = 5 mm
0.15 kg/s
L = 30 m
1.5 × 10 −6 m
ε/D=
= 3 × 10 − 4
0.005 m
The friction factor can be determined from the Moody chart, but to avoid the reading error, we determine it from the
Colebrook equation using an equation solver (or an iterative scheme),
⎞
⎛ 3 × 10 −4
⎛ε / D
1
2.51 ⎞⎟
1
2.51
⎟
→
= −2.0 log⎜
+
= −2.0 log⎜
+
5
⎟
⎜ 3.7
⎜ 3.7 Re f ⎟
×
f
f
1
.
618
10
f
⎠
⎝
⎠
⎝
It gives f = 0.01819. Then the pressure drop, the head loss, and the useful pumping power required become
ΔP = ΔPL = f
L ρV 2
D 2
30 m ( 665.1 kg/m ) (11.49 m/s ) ⎛
1 kN
⎜
0.005 m
2
1000
kg ⋅ m/s 2
⎝
3
= 0.01819
hL =
2
⎞ ⎛ 1 kPa
⎟⎜
2
⎠ ⎝ 1 kN/m
⎞
⎟ = 4792 kPa ≅ 4790 kPa
⎠
ΔPL
L V2
30 m (11.49 m/s) 2
= f
= 0.01819
= 734 m
ρg
0.005 m 2(9.81 m/s 2 )
D 2g
m ΔP (0.15 kg/s )(4792 kPa ) ⎛ 1 kW
⎞
=
= 1.08 kW
W pump = VΔP =
⎜
3
3 ⎟
ρ
665.1 kg/m
⎝ 1 kPa ⋅ m /s ⎠
Therefore, useful power input in the amount of 1.08 kW is needed to overcome the frictional losses in the tube.
Discussion
The friction factor could also be determined easily from the explicit Haaland relation. It would give f =
0.0180, which is sufficiently close to 0.0182. The friction factor corresponding to ε = 0 in this case is 0.0163, which is
about 10% lower. Therefore, the copper tubes in this case are nearly “smooth”.
Also, the power input determined is the mechanical power that needs to be imparted to the fluid. The shaft power
will be more than this due to pump inefficiency; the electrical power input will be even more due to motor inefficiency.
8-25
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-50 [Also solved using EES on enclosed DVD]
Solution
Water is flowing through a brass tube bank of a heat exchanger at a specified flow rate. The pressure drop
and the pumping power required are to be determined. Also, the percent reduction in the flow rate of water through the
tubes is to be determined after scale build-up on the inner surfaces of the tubes.
Assumptions 1 The flow is steady, horizontal, and incompressible. 2 The entrance effects are negligible, and thus the
flow is fully developed (this is a questionable assumption since the tubes are short, and it will be verified). 3 The inlet, exit,
and header losses are negligible, and the tubes involve no components such as bends, valves, and connectors. 4 The piping
section involves no work devices such as pumps and turbines.
Properties
The density and dynamic viscosity of water at 20°C are ρ = 983.3 kg/m3 and μ = 0.467×10-3 kg/m⋅s,
respectively. The roughness of brass tubing is 1.5×10-6 m.
Analysis
First we calculate the average velocity and the
Reynolds number to determine the flow regime:
0.015 m 3 /s
V
V
=
=
= 2.387 m/s
V=
Ac N tune (πD 2 / 4 ) 80[π (0.01 m) 2 / 4]
Re =
80 tubes
ρVD h (983.3 kg/m 3 )(2.387 m/s)(0.01 m)
=
= 50,270
μ
0.467 × 10 −3 kg/m ⋅ s
which is greater than 4000. Therefore, the flow is turbulent. The
1.5 m
relative roughness of the pipe is
1.5 × 10 −6 m
1 cm
= 1.5 × 10 − 4
ε/D=
Water
0.01 m
The friction factor can be determined from the Moody chart, but to avoid the reading error, we determine it from the
Colebrook equation using an equation solver (or an iterative scheme),
⎛ 1.5 × 10 −4
⎛ε / D
1
2.51 ⎞⎟
1
2.51 ⎞⎟
→
= −2.0 log⎜
+
= −2.0 log⎜
+
⎜
⎜ 3.7 Re f ⎟
3 .7
f
f
50,270 f ⎟⎠
⎝
⎠
⎝
It gives f = 0.0214. Then the pressure drop, the head loss, and the useful pumping power required become
⎞⎛ 1 kPa ⎞
L ρV 2
1.5 m (983.3 kg/m 3 )(2.387 m/s) 2 ⎛
1 kN
⎟
⎜
= 8.99 kPa
ΔP = ΔPL = f
= 0.0214
2 ⎟⎜
2 ⎟
⎜
D 2
0.01 m
2
⎝ 1000 kg ⋅ m/s ⎠⎝ 1 kN/m ⎠
⎛ 1 kW
⎞
W pump = VΔP = (0.015 m 3 /s)(8.99 kPa )⎜
⎟ = 0.135 kW
3
⎝ 1 kPa ⋅ m /s ⎠
Therefore, useful power input in the amount of 0.135 kW is needed to overcome the frictional losses in the tube. The
hydrodynamic entry length in this case is
L h, turbulent ≈ 10 D = 10(0.01 m) = 0.1 m
which is much less than 1.5 m. Therefore, the assumption of fully developed flow is valid. (The effect of the entry region is
to increase the friction factor, and thus the pressure drop and pumping power).
After scale buildup: When 1-mm thick scale builds up on the inner surfaces (and thus the diameter is reduced to 0.8 cm
from 1 cm) with an equivalent roughness of 0.4 mm, and the useful power input is fixed at 0.135 kW, the problem can be
formulated as follows (note that the flow rate and thus the average velocity are unknown in this case):
V=
V
V
=
Ac N tune (πD 2 / 4)
Re =
ρVD
→
μ
ε/D=
Re =
→
V=
V
(1)
80[π (0.008 m) 2 / 4]
(983.3 kg/m 3 )V (0.008 m)
(2)
0.467 × 10 −3 kg/m ⋅ s
0.0004 m
= 0.05
0.008 m
8-26
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
⎛ε / D
2.51
= −2.0 log⎜
+
⎜
3
.
7
f
Re f
⎝
1
ΔP = f
L ρV 2
D 2
→ ΔP = f
W pump = 0.135 kW →
⎞
⎟ →
⎟
⎠
1.5 m (983.3 kg/m 3 )V 2
0.008 m
2
VΔP = 0.135
⎛ 0.05
2.51
= −2.0 log⎜
+
⎜
3
.
7
f
Re f
⎝
1
⎛
1 kN
⎜
⎜ 1000 kg ⋅ m/s 2
⎝
⎞
⎟
⎟
⎠
(3)
⎞⎛ 1 kPa ⎞
⎟⎜
⎟⎝ 1 kN/m 2 ⎟⎠ (4)
⎠
(5)
Solving this system of 5 equations in 5 unknown (f, Re, V, ΔP, and V ) using an equation solver (or a trial-and-error
approach, by assuming a velocity value) gives
f = 0.0723, Re = 28,870, V = 1.714 m/s, ΔP = 19.6 kPa, and V = 0.00689 m3/s = 6.89 L/s
Then the percent reduction in the flow rate becomes
Reduction ratio =
Vclean −Vdirty 15 − 6.89
=
= 0.54 = 54%
15
V
clean
Therefore, for the same pump input, the flow rate will be reduced to less than half of the original flow rate when the pipes
were new and clean.
Discussion
The friction factor could also be determined easily from the explicit Haaland relation. Also, the power
input determined is the mechanical power that needs to be imparted to the fluid. The shaft power will be more than this due
to pump inefficiency; the electrical power input will be even more due to motor inefficiency.
Minor Losses
8-51C
Solution
We are to define minor loss and minor loss coefficient.
Analysis
The head losses associated with the flow of a fluid through fittings, valves, bends, elbows, tees, inlets,
exits, enlargements, contractions, etc. are called minor losses, and are expressed in terms of the minor loss coefficient as
h
KL = 2 L
V /( 2 g )
Discussion
Basically, any irreversible loss that is not due to friction in long, straight sections of pipe is a minor loss.
8-52C
Solution
We are to define equivalent length and its relationship to the minor loss coefficient.
Analysis
Equivalent length is the length of a straight pipe which would give the same head loss as the minor loss
component. It is related to the minor loss coefficient by
D
Lequiv = K L
f
Discussion
Equivalent length is not as universal as minor loss coefficient because it depends on the roughness and
Reynolds number of the equivalent straight section of pipe.
8-27
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-53C
Solution
We are to discuss the effect of rounding a pipe inlet.
Analysis
The effect of rounding of a pipe inlet on the loss coefficient is (c) very significant.
Discussion
In fact, the minor loss coefficient changes from 0.8 for a reentrant pipe inlet to about 0.03 for a wellrounded pipe inlet – quite a significant improvement.
8-54C
Solution
We are to discuss the effect of rounding on a pipe outlet.
Analysis
The effect of rounding of a pipe exit on the loss coefficient is (a) negligible.
Discussion
At any pipe outlet, all the kinetic energy is wasted, and the minor loss coefficient is equal to α, which is
about 1.05 for fully developed turbulent pipe flow. Rounding of the outlet does not help.
8-55C
Solution
We are to compare the minor losses of a gradual expansion and a gradual contraction.
Analysis
A gradual expansion, in general, has a greater minor loss coefficient than a gradual contraction in
pipe flow. This is due to the adverse pressure gradient in the boundary layer, which may lead to flow separation.
Discussion
Note, however, that pressure is “recovered” in a gradual expansion. In other words, the pressure rises in the
direction of flow. Such a device is called a diffuser.
8-56C
Solution
We are to discuss ways to reduce the head loss in a pipe flow with bends.
Analysis
Another way of reducing the head loss associated with turns is to install turning vanes inside the elbows.
Discussion
There are many other possible answers, such as: reduce the inside wall roughness of the pipe, use a
larger diameter pipe, shorten the length of pipe as much as possible, etc.
8-57C
Solution
We are to compare two different ways to reduce the minor loss in pipe bends.
Analysis
The loss coefficient is lower for flow through a 90° miter elbow with well-designed vanes (KL ≈ 0.2) than it
is for flow through a smooth curved bend (KL ≈ 0.9). Therefore, using miter elbows with vanes results in a greater
reduction in pumping power requirements.
Discussion
Both values are for threaded elbows. The loss coefficients for flanged elbows are much lower.
8-28
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-58
Solution
Water is to be withdrawn from a water reservoir by drilling a hole at the bottom surface. The flow rate of
water through the hole is to be determined for the well-rounded and sharp-edged entrance cases.
Assumptions 1 The flow is steady and incompressible. 2 The reservoir is open to
the atmosphere so that the pressure is atmospheric pressure at the free surface. 3 The
effect of the kinetic energy correction factor is disregarded, and thus α = 1.
Analysis
The loss coefficient is KL = 0.5 for the sharp-edged entrance, and KL
= 0.03 for the well-rounded entrance. We take point 1 at the free surface of the
reservoir and point 2 at the exit of the hole. We also take the reference level at the
exit of the hole (z2 = 0). Noting that the fluid at both points is open to the atmosphere
(and thus P1 = P2 = Patm) and that the fluid velocity at the free surface is zero (V1 =
0), the energy equation for a control volume between these two points (in terms of
heads) simplifies to
P
V2
P1
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + hturbine, e + h L
ρg
ρg
2g
2g
where the head loss is expressed as h L = K L
z1 = α 2
V 22
V2
+ KL 2
2g
2g
→
z1 = α 2
1
Water
Dhole= 1.5 cm
3m
2
V 22
+ hL
2g
V2
. Substituting and solving for V2 gives
2g
→ 2 gz1 = V 22 (α 2 + K L )
→
V2 =
2 gz1
2 gz1
=
α2 + KL
1+ K L
since α2 = 1. Note that in the special case of KL = 0, it reduces to the Toricelli equation V 2 = 2gz 1 , as expected. Then the
volume flow rate becomes
πD hole
V = AcV 2 =
4
2
2 gz1
1+ K L
Substituting the numerical values, the flow rate for both cases are determined to be
πDhole
Well-rounded entrance: V =
4
2 gz1
π (0.015 m ) 2
=
1+ KL
4
2(9.81 m/s 2 )(3 m)
= 1.34 × 10−3 m3 /s
1 + 0.03
πD hole
V =
4
2 gz1
π (0.015m ) 2
=
1+ K L
4
2(9.81 m/s 2 )(3 m)
= 1.11× 10 −3 m 3 /s
1 + 0.5
2
2
Sharp-edged entrance:
Discussion
The flow rate in the case of frictionless flow (KL = 0) is 1.36×10-3 m3/s. Note that the frictional losses cause
the flow rate to decrease by 1.5% for well-rounded entrance, and 18.5% for the sharp-edged entrance.
8-29
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-59
Solution
Water is discharged from a water reservoir through a circular hole of diameter D at the side wall at a
vertical distance H from the free surface. A relation for the “equivalent diameter” of the sharp-edged hole for use in
frictionless flow relations is to be obtained.
Assumptions 1 The flow is steady and incompressible. 2 The reservoir is open to the atmosphere so that the pressure is
atmospheric pressure at the free surface. 3 The effect of the kinetic energy correction factor is disregarded, and thus α = 1.
Analysis
The loss coefficient is KL = 0.5 for the sharp-edged entrance, and KL = 0 for the “frictionless” flow. We take
point 1 at the free surface of the reservoir and point 2 at the exit of the hole, which is also taken to be the reference level (z2
= 0). Noting that the fluid at both points is open to the atmosphere (and thus P1 = P2 = Patm) and that the fluid velocity at the
free surface is zero (V1 = 0), the energy equation for a control volume between these two points (in terms of heads)
simplifies to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + hturbin e, e + h L
ρg
ρg
2g
2g
where the head loss is expressed as h L = K L
H =α2
V 22
V2
+ KL 2
2g
2g
→
→
H = α2
V 22
+ hL
2g
V2
. Substituting and solving for V2 gives
2g
2 gH = V 22 (α 2 + K L )
→
V2 =
2 gH
2 gH
=
1+ K L
α2 + KL
since α2 = 1. Then the volume flow rate becomes
πD
V = AcV 2 =
4
2
2 gH
1+ K L
(1)
Note that in the special case of KL = 0 (frictionless flow), the velocity relation reduces to the Toricelli equation,
V 2,frictionless = 2 gH . The flow rate in this case through a hole of De (equivalent diameter) is
V = Ac ,equivV 2,frictionless =
2
πDequiv
2 gH
4
Setting Eqs. (1) and (2) equal to each other gives the desired relation for the
equivalent diameter,
2
πDequiv
πD 2 2 gH
2 gH =
4
4
1+ K L
(2)
1
H
Water
D
2
which gives
Dequiv =
D
D
=
= 0.904 D
( 1 + K L )1 / 4 ( 1 + 0.5 )1 / 4
Dequiv < D
Note that the effect of frictional losses of a sharp-edged entrance is to reduce the diameter by about 10%.
Discussion
2
= (0.904 D ) 2 = 0.82 D 2 .
Also, noting that the flow rate is proportional to the square of the diameter, we have V ∝ Dequiv
Therefore, the flow rate through a sharp-edged entrance is about 18% less compared to the frictionless entrance case.
8-30
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-60
Solution
Water is discharged from a water reservoir through a circular hole of diameter D at the side wall at a
vertical distance H from the free surface. A relation for the “equivalent diameter” of the slightly rounded hole for use in
frictionless flow relations is to be obtained.
Assumptions 1 The flow is steady and incompressible. 2 The reservoir is open to the atmosphere so that the pressure is
atmospheric pressure at the free surface. 3 The effect of the kinetic energy correction factor is disregarded, and thus α = 1.
The loss coefficient is KL = 0.12 for the slightly rounded entrance, and KL = 0 for the “frictionless” flow.
We take point 1 at the free surface of the reservoir and point 2 at the exit of the hole, which is also taken to be the
reference level (z2 = 0). Noting that the fluid at both points is open to the atmosphere (and thus P1 = P2 = Patm) and that the
fluid velocity at the free surface is zero (V1 = 0), the energy equation for a control volume between these two points (in
terms of heads) simplifies to
Analysis
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + hturbin e, e + h L
ρg
ρg
2g
2g
where the head loss is expressed as h L = K L
H =α2
V 22
V2
+ KL 2
2g
2g
→
→
H = α2
V 22
+ hL
2g
V2
. Substituting and solving for V2 gives
2g
2 gH = V 22 (α 2 + K L )
→
V2 =
2 gH
2 gH
=
1+ K L
α2 + KL
since α2 = 1. Then the volume flow rate becomes
πD
V = AcV 2 =
4
2
2 gH
1+ K L
(1)
Note that in the special case of KL = 0 (frictionless flow), the velocity relation reduces to the Toricelli equation,
V 2,frictionless = 2gz1 . The flow rate in this case through a hole of De (equivalent diameter) is
V = Ac ,equivV 2,frictionless =
2
πDequiv
2 gH
4
Setting Eqs. (1) and (2) equal to each other gives the desired relation
for the equivalent diameter,
2
πDequiv
πD 2 2 gH
2 gH =
4
4
1+ K L
(2)
1
H
Water
D
2
which gives
Dequiv =
Dequiv < D
D
D
=
= 0.972 D
1/ 4
(1 + KL )
( 1 + 0.12 )1 / 4
Note that the effect of frictional losses of a slightly rounded entrance is to reduce the diameter by about 3%.
Discussion
2
= (0.972 D ) 2 = 0.945D 2 .
Also, noting that the flow rate is proportional to the square of the diameter, we have V ∝ Dequiv
Therefore, the flow rate through a slightly rounded entrance is about 5% less compared to the frictionless entrance case.
8-31
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-61
Solution
A horizontal water pipe has an abrupt expansion. The water velocity and pressure in the smaller diameter
pipe are given. The pressure after the expansion and the error that would have occurred if the Bernoulli Equation had been
used are to be determined.
Assumptions 1 The flow is steady, horizontal, and incompressible. 2 The flow at both the inlet and the outlet is fully
developed and turbulent with kinetic energy corrections factors of α1 = α2 = 1.06 (given).
Properties
We take the density of water to be ρ = 1000 kg/m3.
Analysis
Noting that ρ = const. (incompressible flow), the downstream velocity of water is
A1
D12
πD12 / 4
(0.08 m) 2
(10 m/s) = 2.5 m/s
=
V
=
V
V1 =
1
1
A2
πD 22 / 4
(0.16 m) 2
D 22
The loss coefficient for sudden expansion and the head loss can be calculated from
m 1 = m 2 → ρV1 A1 = ρV 2 A2 → V 2 =
⎛
A
K L = ⎜⎜1 − small
⎜
Alarge
⎝
2
2 2
⎞
2
⎟ = ⎛⎜1 − D1 ⎞⎟ = ⎛⎜1 − 0.08
⎜ 0.16 2
⎟⎟
⎜ D2 ⎟
⎝
2 ⎠
⎝
⎠
2
⎞
⎟ = 0.5625
⎟
⎠
V2
(10 m/s) 2
h L = K L 1 = (0.5625)
= 2.87 m
2g
2(9.81 m/s 2 )
2
Water
1
8 cm
16 cm
10 m/s
Noting that z1 = z2 and there are no pumps or turbines
300 kPa
involved, the energy equation for the expansion section can be
expressed in terms of heads as
P1
V2
P
V2
P1
V2 P
V2
+ α 1 1 + z1 + hpump,u = 2 + α 2 2 + z 2 + hturbine, e + h L
→
+ α 1 1 = 2 + α 2 2 + hL
ρg
ρg
ρg
2g
2g
2 g ρg
2g
Solving for P2 and substituting,
⎧⎪α V 2 − α 2V 2 2
⎫⎪
− gh L ⎬
P2 = P1 + ρ ⎨ 1 1
2
⎪⎩
⎪⎭
⎧⎪1.06(10 m/s) 2 − 1.06(2.5 m/s) 2
⎫⎪⎛
⎞⎛ 1 kPa ⎞
1 kN
⎟⎟⎜
= (300 kPa) + (1000 kg/m 3 )⎨
− (9.81 m/s 2 )(2.87 m)⎬⎜⎜
⎟
2
2
1000
kg
m/s
⋅
⎪⎩
⎪⎭⎝
⎠⎝ 1 kN/m ⎠
= 322 kPa
Therefore, despite the head (and pressure) loss, the pressure increases from 300 kPa to 321 kPa after the expansion. This is
due to the conversion of dynamic pressure to static pressure when the velocity is decreased.
When the head loss is disregarded, the downstream pressure is determined from the Bernoulli equation to be
V 2 − V2 2
P1 V12 P2 V 22
P V2
P1 V12
+
+ z1 = 2 + 2 + z 2 →
+
=
+
→ P1 = P1 + ρ 1
ρg 2 g
ρg 2 g
ρg 2 g ρg 2 g
2
Substituting,
⎞⎛ 1 kPa ⎞
(10 m/s) 2 − (2.5 m/s) 2 ⎛
1 kN
⎟⎟⎜
⎜⎜
P2 = (300 kPa) + (1000 kg/m 3 )
⎟ = 347 kPa
2
2
⎝ 1000 kg ⋅ m/s ⎠⎝ 1 kN/m ⎠
Therefore, the error in the Bernoulli equation is
Error = P2, Bernoulli – P2 = 347 – 322 = 25.0 kPa
Note that the use of the Bernoulli equation results in an error of (347 – 322) / 322 = 0.078 or 7.8%.
Discussion
It is common knowledge that higher pressure upstream is necessary to cause flow, and it may come as a
surprise that the downstream pressure has increased after the abrupt expansion, despite the loss. This is because the sum of
the three Bernoulli terms which comprise the total head, consisting of pressure head, velocity head, and elevation head,
namely [P/ρg + ½V2/g+ z], drives the flow. With a geometric flow expansion, initially higher velocity head is converted to
downstream pressure head, and this increase outweighs the non-convertible and non-recoverable head loss term.
8-32
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
Piping Systems and Pump Selection
8-62C
Solution
We are to compare the flow rate and pressure drop in two pipes of different diameters in series.
Analysis
For a piping system that involves two pipes of different diameters (but of identical length, material, and
roughness) connected in series, (a) the flow rate through both pipes is the same and (b) the pressure drop through the
smaller diameter pipe is larger.
Discussion
The wall shear stress on the smaller pipe is larger, friction factor f is larger, and thus the head loss is higher.
8-63C
Solution
We are to compare the flow rate and pressure drop in two pipes of different diameters in parallel.
Analysis
For a piping system that involves two pipes of different diameters (but of identical length, material, and
roughness) connected in parallel, (a) the flow rate through the larger diameter pipe is larger and (b) the pressure drop
through both pipes is the same.
Discussion
Since the two pipes separate from each other but then later re-join, the pressure drop between the two
junctions must be the same, regardless of which pipe segment is under consideration.
8-64C
Solution
We are to compare the pressure drop of two different-length pipes in parallel.
Analysis
The pressure drop through both pipes is the same since the pressure at a point has a single value, and the
inlet and exits of these the pipes connected in parallel coincide.
Discussion
The length, diameter, roughness, and number and type of minor losses are all irrelevant – for any two pipes
in parallel, both have the same pressure drop.
8-65C
Solution
We are to discuss whether the required pump head is equal to the elevation difference when irreversible
head losses are negligible.
Analysis
Yes, when the head loss is negligible, the required pump head is equal to the elevation difference between
the free surfaces of the two reservoirs.
Discussion
A pump in a piping system may: (1) raise the fluid’s elevation, and/or (2) increase the fluid’s kinetic energy,
and/or (3) increase the fluid’s pressure, and/or (4) overcome irreversible losses. In this case, (2), (3), and (4) are zero or
negligible; thus only (1) remains.
8-66C
Solution
We are to explain how the operating point of a pipe/pump system is determined.
Analysis
The pump installed in a piping system operates at the point where the system curve and the
characteristic curve intersect. This point of intersection is called the operating point.
Discussion
The volume flow rate “automatically” adjusts itself to reach the operating point.
8-33
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-67C
Solution
We are to draw a pump head versus flow
rate chart and identify several parameters.
Head
Analysis
The plot of the head loss versus the flow
rate is called the system curve. The experimentally
determined pump head and pump efficiency versus the
flow rate curves are called characteristic curves. The
pump installed in a piping system operates at the point
where the system curve and the characteristic curve
intersect. This point of intersection is called the
operating point.
Discussion
and the .
hpump
ηpump
System (demand)
curve
Operating
point
By matching the system (demand) curve
Supply
curve
Flow rate
8-34
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-68 [Also solved using EES on enclosed DVD]
Solution
The pumping power input to a piping system with two parallel pipes between two reservoirs is given. The
flow rates are to be determined.
Reservoir B
zB=2 m
Assumptions 1 The flow is steady and incompressible. 2
The entrance effects are negligible, and thus the flow is fully
developed. 3 The elevations of the reservoirs remain constant.
4 The minor losses and the head loss in pipes other than the
parallel pipes are said to be negligible. 5 The flows through
both pipes are turbulent (to be verified).
Reservoir A
zA=2 m
25 m
3 cm
1
2
Properties
The density and dynamic viscosity of water at
20°C are ρ = 998 kg/m3 and μ = 1.002×10-3 kg/m⋅s. Plastic
pipes are smooth, and their roughness is zero, ε = 0.
5 cm
Pump
Analysis
This problem cannot be solved directly since the velocities (or flow rates) in the pipes are not known.
Therefore, we would normally use a trial-and-error approach here. However, nowadays the equation solvers such as EES are
widely available, and thus below we will simply set up the equations to be solved by an equation solver. The head supplied
by the pump to the fluid is determined from
(998 kg/m 3 )V (9.81 m/s 2 )hpump, u
ρVgh pump, u
W elect,in =
→ 7000 W =
(1)
0.68
η pump -motor
We choose points A and B at the free surfaces of the two reservoirs. Noting that the fluid at both points is open to the
atmosphere (and thus PA = PB = Patm) and that the fluid velocities at both points are zero (VA = VB =0), the energy equation
for a control volume between these two points simplifies to
PA
V2
P
V2
+ α A A + z A + h pump, u = B + α B B + z B + hturbine, e + h L
→ h pump, u = ( z B − z A ) + h L
2g
2g
ρg
ρg
or
h pump, u = (9 − 2) + h L (2)
where
h L = h L ,1 = h L ,2
(3) (4)
We designate the 3-cm diameter pipe by 1 and the 5-cm diameter pipe by 2. The average velocity, Reynolds number,
friction factor, and the head loss in each pipe are expressed as
V1
V1
V1
=
→ V1 =
2
Ac,1 πD1 / 4
π (0.03m) 2 / 4
V
V2
V2
→ V2 =
V2 = 2 =
2
Ac ,2 πD 2 / 4
π (0.05m) 2 / 4
V1 =
Re 1 =
ρV1 D1
μ
Re 2 =
ρV 2 D 2
μ
→ Re 1 =
1.002 × 10 −3 kg/m ⋅ s
→ Re 2 =
(998 kg/m 3 )V 2 (0.05 m)
1.002 × 10 −3 kg/m ⋅ s
⎛ε / D
2.51
1
= −2.0 log⎜
+
⎜ 3.7
Re1 f 1
f1
⎝
f2
L1 V12
D1 2 g
h L ,2 = f 2
L 2 V 22
D2 2 g
→
→
h L ,1 = f 1
(7)
(8)
⎛
2.51
= −2.0 log⎜ 0 +
⎜
Re1 f 1
f1
⎝
⎞
⎟ (9)
⎟
⎠
⎞
⎛
⎟ → 1 = −2.0 log⎜ 0 + 2.51
⎟
⎜
Re 2 f 2
f2
⎠
⎝
⎞
⎟ (10
⎟
⎠
⎞
⎟ →
⎟
⎠
⎛ε / D
2.51
2
= −2.0 log⎜
+
⎜ 3.7
Re 2 f 2
⎝
h L,1 = f 1
(6)
(998 kg/m 3 )V1 (0.03 m)
1
1
(5)
1
V12
25 m
0.03 m 2(9.81 m/s 2 )
h L ,2 = f 2
V 22
25 m
0.05 m 2(9.81 m/s 2 )
8-35
(11)
(12)
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
V = V1 + V2
(13)
This is a system of 13 equations in 13 unknowns, and their simultaneous solution by an equation solver gives
V = 0.0183 m 3 /s,
V1 = 0.0037 m 3 /s,
V2 = 0.0146 m 3 /s ,
V1 = 5.30 m/s, V2 = 7.42 m/s, h L = h L,1 = h L, 2 = 19.5 m , hpump,u = 26.5 m
Re1 = 158,300,
Re2 = 369,700, f1 = 0.0164, f2 = 0.0139
Note that Re > 4000 for both pipes, and thus the assumption of turbulent flow is verified.
Discussion
This problem can also be solved by using an iterative approach, but it will be very time consuming.
Equation solvers such as EES are invaluable for this kind of problems.
8-36
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-69E
Solution
The flow rate through a piping system connecting two reservoirs is given. The elevation of the source is to
be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed. 3 The elevations of the reservoirs remain constant. 4 There are no pumps or turbines in the piping system.
Properties
The density and dynamic viscosity of water at 70°F are ρ = 62.30 lbm/ft3 and μ = 2.360 lbm/ft⋅h =
-4
6.556×10 lbm/ft⋅s. The roughness of cast iron pipe is ε = 0.00085 ft.
Analysis
The piping system involves 120 ft of 2-in diameter piping, a well-rounded entrance (KL = 0.03), 4 standard
flanged elbows (KL = 0.3 each), a fully open gate valve (KL = 0.2), and a sharp-edged exit (KL = 1.0). We choose points 1
and 2 at the free surfaces of the two reservoirs. Noting that the fluid at both points is open to the atmosphere (and thus P1 =
P2 = Patm), the fluid velocities at both points are zero (V1 = V2 =0), the free surface of the lower reservoir is the reference
level (z2 = 0), and that there is no pump or turbine (hpump,u = hturbine = 0), the energy equation for a control volume between
these two points simplifies to
P1
V2
P
V2
+ α 1 1 + z1 + h pump, u = 2 + α 2 2 + z 2 + hturbine, e + h L
ρg
ρg
2g
2g
→
z1 = h L
2
⎛ L
⎞V
+
KL ⎟
where h L = h L ,total = h L,major + h L ,minor = ⎜ f
⎝ D
⎠ 2g
since the diameter of the piping system is constant. The average velocity in the
pipe and the Reynolds number are
V
V
10/60 ft 3 /s
V=
=
=
= 7.64 ft/s
Ac πD 2 / 4 π (2 / 12 ft) 2 / 4
∑
ρVD (62.3 lbm/ft 3 )(7.64 ft/s)(2/12 ft)
=
= 60,700
μ
1.307 × 10 −3 lbm/ft ⋅ s
which is greater than 4000. Therefore, the flow is turbulent. The relative
roughness of the pipe is
1
z1
Re =
0.00085 ft
= 0.0051
ε/D=
2 / 12 ft
The friction factor can be determined from the Moody chart, but to avoid the
reading error, we determine it from the Colebrook equation using an equation
solver (or an iterative scheme),
⎛ε / D
⎛ 0.0051
1
2.51 ⎞⎟
1
2.51 ⎞⎟
= −2.0 log⎜
+
→
= −2.0 log⎜
+
⎜
⎟
⎜
3.7 Re f
3. 7
f
f
60,700 f ⎟⎠
⎝
⎠
⎝
It gives f = 0.0320. The sum of the loss coefficients is
∑K
L
120 ft
2 in
10 ft3/min
2
= K L ,entrance + 4 K L,elbow + K L, valve + K L,exit = 0.03 + 4 × 0.3 + 0.2 + 1.0 = 2.43
Then the total head loss and the elevation of the source become
2
2
120 ft
⎛ L
⎞V
⎛
⎞ (7.64 ft/s)
+
= ⎜ (0.0320)
+ 2.43⎟
hL = ⎜ f
KL ⎟
= 23.1 ft
2/12 ft
⎝ D
⎠ 2g ⎝
⎠ 2(32.2 ft/s 2 )
∑
z1 = h L = 23.1 ft
Therefore, the free surface of the first reservoir must be 23.1 ft above the free surface of the lower reservoir to ensure water
flow between the two reservoirs at the specified rate.
Discussion
Note that fL/D = 23.0 in this case, which is almost 10 folds of the total minor loss coefficient. Therefore,
ignoring the sources of minor losses in this case would result in an error of about 10%.
8-37
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-70
Solution
A water tank open to the atmosphere is initially filled with water. A sharp-edged orifice at the bottom drains
to the atmosphere. The initial velocity from the tank and the time required to empty the tank are to be determined.
Assumptions 1 The flow is uniform and incompressible. 2 The flow is turbulent so that the tabulated value of the loss
coefficient can be used. 3 The effect of the kinetic energy correction factor is negligible, α = 1.
The loss coefficient is KL = 0.5 for a sharp-edged entrance.
Properties
Analysis
(a) We take point 1 at the free surface of the tank, and point 2 at the exit of the orifice. We also take the
reference level at the centerline of the orifice (z2 = 0), and take the positive direction of z to be upwards. Noting that the
fluid at both points is open to the atmosphere (and thus P1 = P2 = Patm) and that the fluid velocity at the free surface is very
low (V1 ≅ 0), the energy equation for a control volume between these two points (in terms of heads) simplifies to
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
2g
2g
ρg
ρg
where the head loss is expressed as h L = K L
z1 = α 2
V22
V2
+ KL 2
2g
2g
→
→
z1 = α 2
V 22
+ hL
2g
V2
. Substituting and solving for V2 gives
2g
2 gz1 = V22 (α 2 + K L )
→
V2 =
1
2 gz1
α2 + KL
Water tank
where α2 = 1. Noting that initially z1 = 2 m, the initial velocity is determined to be
V2 =
2 gz1
=
1+ K L
3m
2(9.81 m/s 2 )(2 m)
= 5.11 m/s
1 + 0.5
2m
10 cm
2
The average discharge velocity through the orifice at any given time, in general, can be expressed as
V2 =
2 gz
1+ K L
where z is the water height relative to the center of the orifice at that time.
(b) We denote the diameter of the orifice by D, and the diameter of the tank by D0. The flow rate of water from the tank can
be obtained by multiplying the discharge velocity by the orifice area,
πD
V = AorificeV 2 =
4
2
2 gz
1+ K L
Then the amount of water that flows through the orifice during a differential time interval dt is
dV = Vdt =
πD 2
4
2 gz
dt
1+ K L
(1)
which, from conservation of mass, must be equal to the decrease in the volume of water in the tank,
dV = Atank (−dz ) = −
πD02
dz
(2)
4
where dz is the change in the water level in the tank during dt. (Note that dz is a negative quantity since the positive
direction of z is upwards. Therefore, we used –dz to get a positive quantity for the amount of water discharged). Setting
Eqs. (1) and (2) equal to each other and rearranging,
πD 2
4
πD 2
D2
2 gz
dt = − 0 dz → dt = − 02
1+ K L
4
D
1+ K L
dz
2 gz
→ dt = −
1 + K L −1 / 2
z
dz
2g
D02
D
2
The last relation can be integrated easily since the variables are separated. Letting tf be the discharge time and integrating it
from t = 0 when z = z1 to t = tf when z = 0 (completely drained tank) gives
∫
tf
dt = −
t =0
D02
D
2
1+ K L
2g
∫
0
z
−1 / 2
z = z1
dz →
tf =-
D02
D
2
− 1 +1
1+ K L z 2
2 g − 12 + 1
8-38
0
=
z1
2 D02
D
2
1+ K L 1/ 2
z1
2g
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
Simplifying and substituting the values given, the draining time is determined to be
tf =
D02
D
2
2 z1 (1 + K L )
(3 m) 2
=
g
(0.1 m) 2
2(2 m)(1 + 0.5)
9.81 m/s 2
= 704 s = 11.7 min
Discussion
The effect of the loss coefficient KL on the draining time can be assessed by setting it equal to zero in the
draining time relation. It gives
t f ,zero loss =
D02
D2
2 z1
(3 m) 2
=
g
(0.1 m) 2
2(2 m)
9.81 m/s 2
= 575 s = 9.6 min
Note that the loss coefficient causes the draining time of the tank to increase by (11.7- 9.6)/11.7 = 0.18 or 18%, which is
quite significant. Therefore, the loss coefficient should always be considered in draining processes.
8-39
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-71
Solution
A water tank open to the atmosphere is initially filled with water. A sharp-edged orifice at the bottom drains
to the atmosphere through a long pipe. The initial velocity from the tank and the time required to empty the tank are to be
determined.
Assumptions 1 The flow is uniform and incompressible. 2 The draining pipe is horizontal. 3 The flow is turbulent so that
the tabulated value of the loss coefficient can be used. 4 The friction factor remains constant (in reality, it changes since the
flow velocity and thus the Reynolds number changes). 5 The effect of the kinetic energy correction factor is negligible, so
we set α = 1.
Properties
0.015.
The loss coefficient is KL = 0.5 for a sharp-edged entrance. The friction factor of the pipe is given to be
Analysis
(a) We take point 1 at the free surface of the tank, and point 2 at the exit of the pipe. We take the reference
level at the centerline of the pipe (z2 = 0), and take the positive direction of z to be upwards. Noting that the fluid at both
points is open to the atmosphere (and thus P1 = P2 = Patm) and that the fluid velocity at the free surface is very low (V1 ≅ 0),
the energy equation for a control volume between these two points (in terms of heads) simplifies to
P
V2
P1
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
2g
2g
ρg
ρg
→
z1 = α 2
V 22
+ hL
2g
where
⎛ L
+
h L = h L ,total = h L ,major + h L ,minor = ⎜ f
⎝ D
∑K
L
2
2
⎞V
⎛ L
⎞V
=⎜ f
+ KL ⎟
⎟
⎠ 2g ⎝ D
⎠ 2g
since the diameter of the piping system is constant. Substituting and solving for V2 gives
z1 = α 2
2
V 22 ⎛ L
⎞V
+⎜ f
+ KL ⎟ 2
2g ⎝ D
⎠ 2g
→
V2 =
2 gz1
α 2 + fL / D + K L
1
where α2 = 1. Noting that initially z1 = 2 m, the initial velocity is determined to be
Water tank
2 gz1
2(9.81 m/s 2 )(2 m)
=
= 1.54 m/s
1 + fL / D + K L
1 + 0.015(100 m)/(0.1 m) + 0.5
3m
V 2,i =
2m
10 cm
2
100 m
The average discharge velocity at any given time, in general, can be expressed
as
V2 =
2 gz
1 + fL / D + K L
where z is the water height relative to the center of the orifice at that time.
(b) We denote the diameter of the pipe by D, and the diameter of the tank by Do. The flow rate of water from the tank can
be obtained by multiplying the discharge velocity by the pipe cross-sectional area,
πD
V = A pipeV 2 =
4
2
2 gz
1 + fL / D + K L
Then the amount of water that flows through the pipe during a differential time interval dt is
πD
dV = Vdt =
4
2
2 gz
dt
1 + fL / D + K L
(1)
which, from conservation of mass, must be equal to the decrease in the volume of water in the tank,
dV = Atan k (−dz ) = −
πD02
4
dz
(2)
where dz is the change in the water level in the tank during dt. (Note that dz is a negative quantity since the positive
direction of z is upwards. Therefore, we used –dz to get a positive quantity for the amount of water discharged). Setting
Eqs. (1) and (2) equal to each other and rearranging,
8-40
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
πD02
πD 2
1 + fL / D + K L
1 + fL / D + K L − 12
2 gz
dt = −
dz → dt = −
dz = −
z dz The last relation
4
1 + fL / D + K L
4
2 gz
2g
D
D
can be integrated easily since the variables are separated. Letting tf be the discharge time and integrating it from t = 0 when
z = z1 to t = tf when z = 0 (completely drained tank) gives
∫
tf
dt = −
t =0
1 + fL / D + K L
2g
D02
D
2
∫
D02
2
D02
2
0
z
−1 / 2
z = z1
dz → t f = -
D02
D
2
1
1 + fL / D + K L z 2
1
2g
2
0
=
z1
2 D02
D
2
1 + fL / D + K L 12
z1 Simplifying
2g
and substituting the values given, the draining time is determined to be
tf =
D02
D
2
2 z1 (1 + fL / D + K L )
(3 m) 2
=
g
(0.1 m) 2
2(2 m)[1 + (0.015)(100 m)/(0.1 m) + 0.5]
9.81 m/s 2
= 2334 s = 38.9 min
Discussion
It can be shown by setting L = 0 that the draining time without the pipe is only 11.7 min. Therefore, the
pipe in this case increases the draining time by more than 3 folds.
8-41
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-72
Solution
A water tank open to the atmosphere is initially filled with water. A sharp-edged orifice at the bottom drains
to the atmosphere through a long pipe equipped with a pump. For a specified initial velocity, the required useful pumping
power and the time required to empty the tank are to be determined.
Assumptions 1 The flow is uniform and incompressible. 2 The draining pipe is horizontal. 3 The flow is turbulent so that
the tabulated value of the loss coefficient can be used. 4 The friction factor remains constant. 5 The effect of the kinetic
energy correction factor is negligible, so we set α = 1.
Properties
The loss coefficient is KL = 0.5 for a sharp-edged entrance. The friction factor of the pipe is given to be
0.015. The density of water at 30°C is ρ = 996 kg/m3.
Analysis
(a) We take point 1 at the free surface of the tank, and point 2 at the exit of the pipe. We take the reference
level at the centerline of the orifice (z2 = 0), and take the positive direction of z to be upwards. Noting that the fluid at both
points is open to the atmosphere (and thus P1 = P2 = Patm) and that the fluid velocity at the free surface is very low (V1 ≅ 0),
the energy equation for a control volume between these two points (in terms of heads) simplifies to
P
V2
P1
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
2g
2g
ρg
ρg
→
z1 + hpump, u = α 2
V 22
+ hL
2g
where α2 = 1 and
⎛ L
+
h L = h L ,total = h L ,major + h L ,minor = ⎜ f
⎝ D
∑
2
2
⎞V
⎛ L
⎞V
=⎜ f
+ KL ⎟
KL ⎟
⎠ 2g ⎝ D
⎠ 2g
since the diameter of the piping system is constant. Substituting and noting that the initial discharge velocity is 4 m/s, the
required useful pumping head and power are determined to be
m = ρAcV 2 = ρ (πD 2 / 4 )V 2 = (996 kg/m 3 )[π (0.1 m) 2 /4](4 m/s ) = 31.3 kg/m 3
2
2
L
100 m
⎛
⎞V
⎛
⎞ (4 m/s)
+ K L ⎟ 2 − z1 = ⎜1 + (0.015)
+ 0.5 ⎟
− (2 m) = 11.46 m
h pump, u = ⎜1 + f
D
0.1 m
⎝
⎠ 2g
⎝
⎠ 2(9.81 m/s 2 )
⎛
⎞⎛ 1 kW ⎞
1 kN
⎟
= 3.52 kW
W pump, u = VΔP = m ghpump, u = (31.3 kg/s)(9.81 m/s 2 )(11.46 m)⎜
⎜ 1000 kg ⋅ m/s 2 ⎟⎜⎝ 1 kN ⋅ m/s ⎟⎠
⎝
⎠
Therefore, the pump must supply 3.52 kW of mechanical energy to water. Note that the shaft power of the pump must be
greater than this to account for the pump inefficiency.
(b) When the discharge velocity remains constant, the flow rate of water becomes
V = AcV 2 = (πD 2 / 4 )V 2 = [π (0.1 m) 2 /4](4 m/s ) = 0.03142 m 3 /s
1
The volume of water in the tank is
V = Atank z1 = (πD02 / 4) z1 = [π (3 m) 2 /4](2 m) = 14.14 m 3
Then the discharge time becomes
V
14.14 m 3
Δt = =
= 450 s = 7.5 min
V 0.03142 m 3 /s
Water tank
10 m
2m
10 cm 100 m
Pump
2
4 m/s
Discussion
1 Note that the pump reduces the discharging time from 38.9 min to 7.5 min. The assumption of constant discharge velocity
can be justified on the basis of the pump head being much larger than the elevation head (therefore, the pump will dominate
the discharging process). The answer obtained assumes that the elevation head remains constant at 2 m (rather than
decreasing to zero eventually), and thus it under predicts the actual discharge time. By an exact analysis, it can be shown
that when the effect of the decrease in elevation is considered, the discharge time becomes 468 s = 7.8 min. This is
demonstrated below.
2 The required pump head (of water) is 11.46 m, which is more than 10.3 m of water column which corresponds to the
atmospheric pressure at sea level. If the pump exit is at 1 atm, then the absolute pressure at pump inlet must be negative ( =
-1.16 m or – 11.4 kPa), which is impossible. Therefore, the system cannot work if the pump is installed near the pipe exit,
8-42
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
and cavitation will occur long before the pipe exit where the pressure drops to 4.2 kPa and thus the pump must be installed
close to the pipe entrance. A detailed analysis is given below.
Demonstration 1 for Prob. 8-72 (extra) (the effect of drop in water level on discharge time)
Noting that the water height z in the tank is variable, the average discharge velocity through the pipe at any given time, in
general, can be expressed as
2
2 g ( z + hpump, u )
L
⎛
⎞V
+ K L ⎟ 2 − z → V2 =
hpump, u = ⎜1 + f
1 + fL / D + K L
D
⎝
⎠ 2g
where z is the water height relative to the center of the orifice at that time. We denote the diameter of the pipe by D, and the
diameter of the tank by D0. The flow rate of water from the tank can be obtained by multiplying the discharge velocity by
the cross-sectional area of the pipe,
πD
V = A pipeV 2 =
4
2
2 g ( z + hpump, u )
1 + fL / D + K L
Then the amount of water that flows through the orifice during a differential time interval dt is
πD 2 2 g ( z + h pump, u )
dV = Vdt =
dt
(1)
4
1 + fL / D + K L
which, from conservation of mass, must be equal to the decrease in the volume of water in the tank,
πD 2
(2)
dV = Atan k (−dz ) = − 0 dz
4
where dz is the change in the water level in the tank during dt. (Note that dz is a negative quantity since the positive
direction of z is upwards. Therefore, we used –dz to get a positive quantity for the amount of water discharged). Setting
Eqs. (1) and (2) equal to each other and rearranging,
πD 2
2 g ( z + hpump,u )
4
1 + fL / D + K L
dt = −
πD02
4
dz
→ dt = −
D02
D2
1 + fL / D + K L
−1
( z + hpump,u ) 2 dz
2g
The last relation can be integrated easily since the variables are separated. Letting tf be the discharge time and integrating it
from t = 0 when z = z1 to t = tf when z = 0 (completely drained tank) gives
∫
tf
dt = −
t =0
D02
2
1 + fL / D + K L
2g
D
Performing the integration gives
1
D 2 1 + fL / D + K L ( z + hpump ) 2
t f = - 02
1
2g
D
2
∫
0
=
z1
0
z = z1
( z + hpump, u ) −1 / 2 dz
2hpump (1 + fL / D + K L ) ⎞
D02 ⎛⎜ 2( z1 + hpump )(1 + fL / D + K L )
⎟ Substituting the
−
2⎜
⎟
g
g
D ⎝
⎠
values given, the draining time is determined to be
(3 m) 2 ⎛ 2(2 + 11.46 m)[1 + 0.015 × 100/0.1 + 0.5]
2(11.46 m)[1 + 0.015 × 100/0.1 + 0.5] ⎞
⎜
⎟
−
2 ⎜
2
⎟
(0.1 m) ⎝
9.81 m/s
9.81 m/s 2
⎠
= 468 s = 7.8 min
tf =
Demonstration 2 for Prob. 8-72 (on cavitation)
We take the pump as the control volume, with point 1 at the inlet and point 2 at the exit. We assume the pump inlet and
outlet diameters to be the same and the elevation difference between the pump inlet and the exit to be negligible. Then we
have z1 ≅ z2 and V1 ≅ V2. The pump is located near the pipe exit, and thus the pump exit pressure is equal to the pressure at
the pipe exit, which is the atmospheric pressure, P2 = Patm. Also, the can take hL = 0 since the frictional effects and loses in
the pump are accounted for by the pump efficiency. Then the energy equation for the pump (in terms of heads) reduces to
P
V2
P1
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + h turbine, e + h L
2g
2g
ρg
ρg
Solving for P1 and substituting,
8-43
→
P1,abs
ρg
+ hpump, u =
Patm
ρg
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
P1,abs = Patm − ρghpump, u
⎞⎛ 1 kPa ⎞
⎛
1 kN
⎟
= (101.3 kPa) − (996 kg/m 3 )(9.81 m/s 2 )(11.46 m)⎜
= - 10.7 kPa
⎜ 1000 kg ⋅ m/s 2 ⎟⎜⎝ 1 kN/m 2 ⎟⎠
⎠
⎝
which is impossible (absolute pressure cannot be negative). The technical answer to the question is that cavitation will
occur since the pressure drops below the vapor pressure of 4.246 kPa. The practical answer is that the question is invalid
(void) since the system will not work anyway. Therefore, we conclude that the pump must be located near the beginning,
not the end of the pipe. Note that when doing a cavitation analysis, we must work with the absolute pressures. (If the
system were installed as indicated, a water velocity of V = 4 m/s could not be established regardless of how much pump
power were applied. This is because the atmospheric air and water elevation heads alone are not sufficient to drive such
flow, with the pump restoring pressure after the flow.)
To determine the furthest distance from the tank the pump can be located without allowing cavitation, we assume
the pump is located at a distance L* from the exit, and choose the pump and the discharge portion of the pipe (from the
pump to the exit) as the system, and write the energy equation. The energy equation this time will be as above, except that
hL (the pipe losses) must be considered and the pressure at 1 (pipe inlet) is the cavitation pressure, P1 = 4.246 kPa:
P1
V2
P
V2
+ α 1 1 + z1 + hpump, u = 2 + α 2 2 + z 2 + hturbine, e + h L
2g
2g
ρg
ρg
→
P1,abs
ρg
+ hpump, u =
Patm
L* V 2
+f
ρg
D 2g
P1,abs − Patm
L* V
=
+ h pump, u
D 2g
ρg
Substituting the given values and solving for L* gives
2
or
f
(4 m/s) 2
(4.246 − 101.3) kN/m 2 ⎛⎜ 1000 kg ⋅ m/s 2
L*
=
0.1 m 2(9.81 m/s 2 ) (996 kg/m 3 )(9.81 m/s 2 ) ⎜⎝
1 kN
⎞
⎟ + (11.46 m) → L* = 12.5 m
⎟
⎠
Therefore, the pump must be at least 12.5 m from the pipe exit to avoid cavitation at the pump inlet (this is where the
lowest pressure occurs in the piping system, and where the cavitation is most likely to occur).
Cavitation onset places an upper limit to the length of the pipe on the suction side. A pipe slightly longer would
become vapor bound, and the pump could not pull the suction necessary to sustain the flow. Even if the pipe on the suction
side were slightly shorter than 100 – 12.5 = 87.5 m, cavitation can still occur in the pump since the liquid in the pump is
usually accelerated at the expense of pressure, and cavitation in the pump could erode and destroy the pump.
Also, over time, scale and other buildup inside the pipe can and will increase the pipe roughness, increasing the
friction factor f, and therefore the losses. Buildup also decreases the pipe diameter, which increases pressure drop.
Therefore, flow conditions and system performance may change (generally decrease) as the system ages. A new system
that marginally misses cavitation may degrade to where cavitation becomes a problem. Proper design avoids these
problems, or where cavitation cannot be avoided for some reason, it can at least be anticipated.
(0.015)
8-44
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-73
Solution
Oil is flowing through a vertical glass funnel which is always maintained full. The flow rate of oil through
the funnel and the funnel effectiveness are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed (to be verified). 3 The frictional loses in the cylindrical reservoir are negligible since its diameter is very large
and thus the oil velocity is very low.
Properties
The density and viscosity of oil at 20°C are ρ = 888.1 kg/m3 and μ = 0.8374 kg/m⋅s.
Analysis
We take point 1 at the free surface of the oil in the cylindrical reservoir, and point 2 at the exit of the funnel
pipe which is also taken as the reference level (z2 = 0). The fluid at both points is open to the atmosphere (and thus P1 = P2
= Patm) and that the fluid velocity at the free surface is negligible (V1 ≅ 0). For the ideal case of “frictionless flow,” the exit
velocity is determined from the Bernoulli equation to be
P1 V12
P V2
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
Substituting,
→
V 2 = V 2,max = 2gz 1
1
V 2,max = 2 gz1 = 2(9.81 m/s 2 )(0.40 m ) = 2.801 m/s
Vmax = V 2,max A2 = V 2,max (πD 22 / 4)
1 cm
= (2.801 m/s)[π (0.01 m) 2 / 4] = 2.20 × 10 − 4 m 3 /s
ρVD (888.1 kg/m 3 )(2.801 m/s)(0.01 m)
Re =
=
= 29.71
0.8374 kg/m ⋅ s
μ
15 cm
Oil
This is the flow velocity for the frictionless case, and thus it is the maximum flow
velocity. Then the maximum flow rate and the Reynolds number become
25 cm
2
which is less than 2300. Therefore, the flow is laminar, as postulated. (Note that in the actual case the velocity and thus the
Reynolds number will be even smaller, verifying the flow is always laminar). The entry length in this case is
Lh = 0.05 Re D = 0.05 × 29.71× (0.01 m ) = 0.015 m
which is much less than the 0.25 m pipe length. Therefore, the entrance effects can be neglected as postulated.
Noting that the flow through the pipe is laminar and can be assumed to be fully developed, the flow rate can be
determined from the appropriate relation with θ = -90° since the flow is downwards in the vertical direction,
( ΔP − ρgL sin θ )πD 4
V =
128μL
where ΔP = Ppipe inlet − Ppipe exit = ( Patm + ρghcylinder ) − Patm = ρghcylinder is the pressure difference across the pipe, L = hpipe,
and sin θ = sin (-90°) = -1. Substituting, the flow rate is determined to be
ρg (hcylinder + hpipe )πD 4
(888.1 kg/m 3 )(9.81 m/s 2 )(0.15 + 0.25 m)π (0.01 m) 4
= 4.09 × 10 -6 m 3 /s
128μL
128(0.8374 kg/m ⋅ s)(0.25 m)
Then the “funnel effectiveness” becomes
4.09 × 10 −6 m 3 /s
V
=
= 0.0186 or 1.86%
Eff =
Vmax 2.20 × 10 − 4 m 3 /s
V =
=
Note that the flow is driven by gravity alone, and the actual flow rate is a small fraction of the flow rate that
Discussion
would have occurred if the flow were frictionless.
8-45
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 8 Flow in Pipes
8-74
Solution
Oil is flowing through a vertical glass funnel which is always maintained full. The flow rate of oil through
the funnel and the funnel effectiveness are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The entrance effects are negligible, and thus the flow is fully
developed (to be verified). 3 The frictional loses in the cylindrical reservoir are negligible since its diameter is very large
and thus the oil velocity is very low.
The density and viscosity of oil at 20°C are ρ = 888.1 kg/m3 and μ = 0.8374 kg/m⋅s.
Properties
Analysis
We take point 1 at the free surface of the oil in the cylindrical reservoir, and point 2 at the exit of the funnel
pipe, which is also taken as the reference level (z2 = 0). The fluid at both points is open to the atmosphere (and thus P1 = P2
= Patm) and that the fluid velocity at the free surface is negligible (V1 ≅ 0). For the ideal case of “frictionless flow,” the exit
velocity is determined from the Bernoulli equation to be
P1 V12
P V2
+
+ z1 = 2 + 2 + z 2
ρg 2 g
ρg 2 g
→
V 2 = V 2,max = 2gz 1
1
(a) Case 1: Pipe length remains constant at 25 cm, but the pipe diameter is doubled
to D2 = 2 cm:
15 cm
Oil
Substitution gives
V 2,max = 2 gz1 = 2(9.81 m/s 2 )(0.40 m ) = 2.801 m/s
This is the flow velocity for the frictionless case, and thus it is the maximum flow
velocity. Then the maximum flow rate and the Reynolds number become
Vmax = V 2,max A2 = V 2,max (πD 22 / 4) = (2.801 m/s)[π (0.02 m) 2 / 4]
= 8.80 × 10
Re =
−4
2 cm
25 cm
2
3
m /s
ρVD (888.1 kg/m 3 )(2.801 m/s)(0.02 m)
=
= 59.41
0.8374 kg/m ⋅ s
μ
which is less than 2300. Therefore, the flow is laminar. (Note that in the actual case the velocity and thus the Reynolds
number will be even smaller, verifying the flow is always laminar). The entry length is
Lh = 0.05 Re D = 0.05 × 59.41× (0.02 m ) = 0.059 m
which is considerably less than the 0.25 m pipe length. Therefore, the entrance effects can be neglected (with reservation).
Noting that the flow through the pipe is laminar and can be assumed to be fully developed, the flow rate can be
determined from the appropriate relation with θ = -90° since the flow is downwards in the vertical direction,
(ΔP − ρgL sin θ )πD 4
V =
128μL
where ΔP = Ppipe inlet − Ppipe exit = ( Patm + ρghcylinder ) − Patm = ρghcylinder is the pressure difference across the pipe, L = hpipe,
and sin θ = sin (-90°) = -1. Substituting, the flow rate is determined to be
V =
ρg (hcylinder + hpipe )πD 4
128μL
=
(888.1 kg/m 3 )(9.81 m/s 2 )(0.15 + 0.25 m)π (0.02 m) 4
= 6.54 × 10 - 5 m 3 /s
128(0.8374 kg/m ⋅ s)(0.25 m)
Then the “funnel effectiveness” becomes
Eff =
V
V
max
=
0.654 × 10 −4 m 3 /s
8.80 × 10 − 4 m 3 /s
= 0.074
or
7.4%
15 cm
Oil
(b) Case 2: Pipe diameter remains constant at 1 cm, but the pipe length is doubled
to L = 50 cm:
Substitution gives
V 2,max = 2 gz1 = 2(9.81 m/s 2 )(0.65 m ) = 3.571 m/s
8-46
1 cm
50 cm
PROPRIETARY MATERIAL. © 2006 The McGraw-Hill Companies, Inc. Limited distribution permitted only to
teachers and educators for course preparation. If you are a student using this Manual