Products conforming to RoHS directive
BS-98
Base Station
OPERATION MANUAL
Products conforming to RoHS directive
BS-98
Base Station
OPERATION MANUAL
OUTLINE
1
NAME and FUNCTION
2
FORMATS and GENLOCK
3
EQUIPMENT
CONNECTIONS
BS SETTINGS and
ADJUSTMENT
TROUBLE SHOOTING and
MAINTENANCE
CHANGING INFORMATION
1409 1st Edition (U) (E)
4
5
6
Copyright © 2014 Ikegami Tsushinki Co., Ltd.
We reserve the copyright on the software we create.
No part of this publication may be modified or reproduced in any form, or by any means, without prior written permission from Ikegami Tsushinki Co., Ltd.
PRODUCTS CONFORMING TO RoHS DIRECTIVE
PRODUCTS CONFORMING TO RoHS DIRECTIVE
Following products described in this manual are products conforming to RoHS directive.
• BS-98 Base Station
Products conforming to RoHS directive include products that do not contain specified hazardous substances such as lead, mercury,
cadmium, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) in electrical and
electronic equipment excluding following exemption applications based on the EU directive (Directive2002/95/EC).
* About RoHS Directive
The RoHS directive stands for "the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment"
and is one of environmental directives in Europe. This directive restricts the use of specified hazardous substances in electrical and
electronic equipment.
● Applications exempted from RoHS directive compliance
Followings applications are permitted as exemptions from RoHS directive compliance.
1. Mercury in compact fluorescent lamps not exceeding 5mg per lamp
2. Mercury in straight fluorescent lamps for general purposes not exceeding:
• halophosphate 10mg
• triphosphate with a normal lifetime 5mg
• triphosphate with a long lifetime 8mg
3. Mercury in straight fluorescent lamps for special purposes
4. Mercury in other lamps not specifically mentioned in this Annex
5. Lead in the glass of cathode ray tubes, electronic components and fluorescent tubes
6. Lead as an alloying element in steel containing up to 0.35% lead by weight, aluminum containing up to 0.4% lead by weight and
as a copper alloy containing up to 4% lead by weight
7. Lead in following items
• Lead in high melting temperature type solders (i.e. tin-lead solder alloys containing more than 85% lead)
• Lead in solders for servers, storage and storage array systems
• Lead in solders for network infrastructure equipment for switching, signaling, transmission as well as network management
for telecommunication
• Lead in electronic ceramic parts (e.g. piezoelectronic devices)
8. Cadmium plating except for applications banned under Directive 91/338/EEC amending Directive 76/769/EEC relating to
restrictions on the marketing and use of certain dangerous substances and preparations
9. Hexavalent chromium as an anti-corrosion of the carbon steel cooling system in absorption refrigerators
10. Lead used in compliant pin connector systems
11. Lead as a coating material for the thermal conduction module C-ring
12.Lead and cadmium in optical and filter glass
13. Lead in solders consisting of more than two elements for the connection between the pins and the package of microprocessors
with a lead content of more than 80% and less than 85% by weight
14. Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit Flip
Chip packages
15. Decabrominated diphenyl ether (Deca-BDE) in polymeric applications
BS-98 1409 VER1 (U) (E)
i
MAINTENANCE OF PRODUCTS CONFORMING TO RoHS DIRECTIVE
MAINTENANCE OF PRODUCTS CONFORMING TO RoHS DIRECTIVE
Work with care about followings for maintenance of products conforming to RoHS directive.
1. Identification
- For products conforming to RoHS directive, the letter "E" is appended at the end of the serial number on the label. For models
that the letter cannot be appended to the serial number, the letter "E" will be described in a distinguishable position on the label.
A description example on a main label is shown below.
BS- * * *
BASE STATION
- Print-circuit board of the products conforming to RoHS directive is manufactured by following methods.
[1] Blue resist ink is used for the print-circuit board. (The color of conventional print-circuit board is green.)
[2] Either one of the following marks is indicated by a serigraph or label.
2. Soldering
Since the melting point of lead-free solder used for the products conforming to RoHS directive is 20 to 45 degrees Celsius higher
than that of conventional solder with lead (Sn-Pb eutectic solder), a high temperature needs to be set to a soldering iron. Taking
allowable temperature limit of the parts and stable work into consideration, use a soldering iron with excellent thermal recovery
characteristics.
- Recommended solder composition is "Sn/3.0Ag/0.5Cu" or equivalent.
- Separate the soldering iron exclusively for RoHS products and the soldering iron for conventional use.
- Set the temperature of the soldering bit to 350 to 370 degrees Celsius.
The temperature may need to be adjusted according to the size of the copper foil land on the print-circuit board and the tip width
of the soldering bit.
- Finish by a lead-free solder looks dull or whitish compared to conventional solder with lead.
- If the customer mixed the lead-solder with the main body wiring or the circuit board, it becomes guarantee off the subject.
Ikegami doesn't guarantee to do the repair work. Because the solder polluted with lead cannot be removed.
3. Parts
Be sure to use parts conforming to RoHS directive.
ii
BS-98 1409 VER1 (U) (E)
INFORMATION TO THE USER
INFORMATION TO THE USER
1. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
2. Declaration of conformity
The CE mark means that the following products will meet the Directive 2004/108/EC,2006/95/EC and the Standards EN55103-1
E4-E5, EN55103-2 E4-E5 (for EMC), EN60950-1 (for LVD).
For European customer.
3. Please use it by less than 10m, when you use cable of MIC1 OUT, MIC2 OUT, AUD TRUNK, INTERCOM, and DIGITAL
AUDIO.
4. We carried out a test in accordance with EN55103-1 Annex B. As a result, the value of the inrush current is as follows.
Inrush current
BS-98 + HDK-79GX + FA-97 + COP-399 : 7.42A
5. Use shielded cable except AC cable.
6. This equipment doesn't intend to use at residential areas, so that use in residential areas may cause interference.
People’s Republic of China Electronic Industry Standard (SJ/T11364—2006)
Marking Styles for Names and Contents of Toxic or hazardous Substances and Elements
Toxic or hazardous Substances and Elements
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr/(VI))
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
BS-98
×
○
○
○
○
○
CCU-980
×
○
○
○
○
○
Part Name
○ : Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement in SJ/T11363-2006.
× : Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is
above the limit requirement in SJ/T11363-2006.
BS-98 1409 VER1 (U) (E)
iii
SAFETY PRECAUTIONS
SAFETY PRECAUTIONS
This manual describes the precautions using various pictorial symbols for you to use the product safely. Please read these
precautions thoroughly before use. The symbols and meanings are as follows:
The following hazard alert symbols are used to indicate the level of impact on the body or property
when you do not follow the precautions.
Indicates that mishandling of the product by ignoring this label may lead to a danger resulting in a
serious injury or death.
Indicates that mishandling of the product by ignoring this label may lead to a danger resulting in an
injury or property damage.
The following symbols are used to indicate the expected injury or hazards when you do not follow
the precautions.
Indicates general cautions on such matters as safe work, procedure, and installation location.
Mishandling may not directly lead to death, injury, or property damage.
Indicates that mishandling may cause an electric shock.
Indicates that mishandling may cause a fire.
Indicates that mishandling may cause injury.
The following symbol is used to indicate other precautions to prevent damage or hazard from
occurring:
Indicates prohibited action.
iv
BS-98 1409 VER1 (U) (E)
SAFETY PRECAUTIONS
■ Handling Precautions
Regarding the Product
Do not disassemble or modify the product which is not described in this manual. Doing so may
cause fire, electric shock, or injury.
Regarding the Power
When you disconnect the cable, be sure to hold the plug and pull. Failure to do so may cause a fire
or electric shock due to a damaged cable.
To inspect or operate on the inside of the equipment, turn off the power and wait for one or two
minutes before starting work. High voltage is present in some modules and connectors of this
product.
Regarding the Product
Avoid use or storage in the following conditions:
- Extremely high/low temperature
- In direct sunlight for a long time, or near a heater
- High humidity or dusty
- Exposed to water or other liquid
- Strong vibration or shock
- Strong magnetic field or radio waves
- lightning
- In rain without the rain cover
Be sure to hold the plug and pull when you disconnect the cable.
Condensation that cause malfunction may occur in the equipment.
Avoid moving the equipment suddenly from an extremely cold place to a warm place.
Condensation may occur in the Charged Couple Device (CCD) or other parts.
Do not drop or insert a metal object such as a pin or a foreign object into the equipment.
Do not spread or spill water or other liquid on the equipment.
Do not subject the equipment to a strong shock or vibration.
Doing so may cause damage or malfunction of the equipment.
Excessive sound pressure from the headset may cause a hearing loss.
BS-98 1409 VER1 (U) (E)
v
SAFETY PRECAUTIONS
Regarding the Modules
Pay attention to the following points when handling the modules:
- Do not let the parts of the modules or the printed wiring pattern to touch the metal parts that can
be energized.
- Avoid placing or storing the modules in humid places.
- Do not touch the parts of the modules or the printed wiring pattern with dirty or wet hands. Do
not touch them with hands unless necessary.
Regarding the Power and the Lithium Battery
Use the product in compliance with the rating of the fuse. Otherwise, a fault can occur.
Do not use an unspecified battery.
Wrong usage of batteries may cause liquid leak, explosion, and heat, and at worst injury or fire.
When changing or discarding a battery, please contact Ikegami's sales and service centers.
■ Maintenance
Regarding the product
Before performing maintenance on the product, be sure to turn off the power for safety and for
protection against malfunction.
Clean the product using a dry and soft cloth.
If the product is very dirty, wipe with a cloth moistened with water or neutral detergent and wrung
out. If neutral detergent is used, wipe again with a cloth dipped in clear water and wrung out.
■ Regular Maintenance Recommended
This product includes parts that wear out and have a limited life even in proper use or storage. Therefore, regular maintenance (once
every 3 years or 8000 hours use) is recommended to extend the life and safe use of this product for a long time. Please contact
Ikegami's sales and service centers or Techno Ikegami Co., Ltd. for the regular maintenance and repair of our products.
vi
BS-98 1409 VER1 (U) (E)
HOW TO READ THE OPERATION MANUAL
HOW TO READ THE OPERATION MANUAL
This page explains general notes on reading the BS-98 Operation Manual, and the symbols and notations used in the manual.
■ Notes on the Manual
- The target readers of this manual are the people, who has basic knowledge on handling of television cameras for broadcasting,
base stations, and/or control panels.
- The contents of this manual are subject to change without notice in the future.
■ Symbols
The symbols used in this manual are as follows:
CAUTION:
Things you have to be careful during operation. Be sure to read.
Note:
Supplementary information or guidance
Reference:
Sections where related information is available
■ Notations
The following notations are used in this manual.
This product, BS
Indicates BS-98 Base Station.
Camera head
Indicates general broadcast cameras.
■ Illustrations and Displays
The illustrations and displays in the text are provided for explanation and may be slightly different from the actual equipment or
image.
■ Related Manuals
Refer to the operation manuals and maintenance manuals accompanying the camera head, BS, and each control panel to be used.
BS-98 1409 VER1 (U) (E)
vii
HOW TO READ THE OPERATION MANUAL
■ Structure of Operation Manual
BS-98 Camera Control Unit Operation Manual is intended to both safely and smoothly operate the BS-98. The Operation Manual
consists of six chapters. By reading it in sequence, you can smoothly perform a series of steps, from connection to operation.
Chapter 1
Chapter 2
Chapter 3
OUTLINE
Explains the features and the specifications of this product.
If you are not familiar with BS-98, please start with this chapter.
NAME and FUNCTION
Explains the name and function of each part of the BS-98.
FORMATS and GENLOCK
Explains the signal formats of the BS-98.
Chapter 4
Chapter 5
Chapter 6
EQUIPMENT CONNECTIONS
Also explains how to connect this product to camera and the peripheral equipment and examples to
operate this product.
BS SETTINGS and ADJUSTMENT
Explains the menu of the BS-98 and DIP switch settings on the modules inside of the BS.
TROUBLE SHOOTING and MAINTENANCE
BS-98 is equipped with the self-diagnostic function. When the alarm lamp lights during the
operation of this product, read here to know the problem. This chapter also explains the regular
maintenance such as cleaning of connectors and replacement of fuses.
CHANGING INFORMATION
This manual is written for the standard specifications. Your custom specifications and revision
information are addressed in "CHANGING INFORMATION". Read by comparing with the main
text of the maintenance manual. ("CHANGING INFORMATION" may be sent to you later on.).
viii
BS-98 1409 VER1 (U) (E)
CONTENTS
BS-98
BASE STATION
OPERATION MANUAL
PRODUCTS CONFORMING TO RoHS DIRECTIVE
i
MAINTENANCE OF PRODUCTS CONFORMING TO
RoHS DIRECTIVE
ii
INFORMATION TO THE USER
iii
SAFETY PRECAUTIONS
iv
HOW TO READ THE OPERATION MANUAL
vii
Chapter 5 BS SETTINGS and ADJUSTMENT
5.1
(Operation from the MCP)
55
55
Basic Operation of the Menu
(Operation from the OCP-200)
57
Basic operation of the menu screen
Chapter 1 OUTLINE
1.1
Settings from the BS Menu
Basic Operation of the Menu
Features of This Product
(when operated from the CCU/BS main body)
59
3
Menu Configuration
60
66
1.2
Specifications
4
BARS TITLE
1.3
External Dimensions Diagram
9
PRESET FILE LOAD
67
HEAD MENU
68
INFORMATION
69
70
Chapter 2 NAME and FUNCTION
2.1
2.2
BS-98 Front View
13
SYSTEM FORMAT
BS-98 front display and operation unit
13
OUTPUT FORMAT
71
BS-98 Front View With the Front Cover Off
16
RET VIDEO FORMAT
73
BS-98 Rear View
19
PHASE CONTROL
74
Modules on the Rear of the BS-98
21
AUDIO MANAGEMENT
76
INCOM MANAGEMENT
77
HDTV VIDEO PROCESS
79
SDTV VIDEO PROCESS
80
Chapter 3 FORMATS and GENLOCK
3.1
3.2
HDTV Format
GENLOCK System
27
30
Input Connectors
30
Output Connectors
30
Chapter 4 EQUIPMENT CONNECTIONS
4.1
HD PM VIDEO PROCESS
81
SD PM VIDEO PROCESS
82
FUNCTION SETTING
83
ENGINEER SET FILE RENEW
84
PASSWORD ENTRY
85
PROGRAM UPDATE
86
Preparation
37
Settings Using Switches on the Module
87
Product Use Environment
37
Tally Mode Settings
87
Make Sure the Power Switch is OFF
37
PGM Settings
88
4.2
Power Supply
38
4.3
BS and Camera Head Connection
41
4.4
System Setup Diagram
42
4.5
Operating Systems
44
4.6
External Connections
45
5.2
Chapter 6 TROUBLE SHOOTING and MAINTENANCE
6.1
Indicator on the Front of BS Lights
6.2
ALARM Indicator on the Control Panel
Flashes ON and OFF
95
BS Self Diagnostic Information
95
CHANGING INFORMATIO
BS-98 1409 VER1 (U) (E)
91
99
ix
x
BS-98 1409 VER1 (U) (E)
1
OUTLINE
2
BS-98 1409 VER1 (U) (E)
1.1 Features of This Product
BS-98 is the half-rack size base station that can configure the 3G-compatible "Unicam HD" camera series and the multi format
system by the image circuit corresponding to the 3 Gbps transmission and 3G-SDI format.
The base station and the camera head are connected by the 8-core optical fiber composite camera cable (two single mode fibers,
four power supply lines, and two control lines). It can be extended to the maximum of 1000m(*) by the optical serial digital
transmission method that is conformable to SMPTE425 (Level-B) [international standard] when operating the large camera head
and build-up unit.
* The maximum cable length varies according to the type of lens and the use of utility power.
1.1
Features of This Product
■ Transmission between the Camera Head and BS with 3G-SDI.
Transmission is possible between the camera head and BS with 3G-SDI. 1080 progressive scans of the camera head, the highdefinition format of 1080i RGB4:4:4, and the 2X speed images of the slow motion format can be output from BS.
When 3G-SDI format is operated, HD-SDI and DUAL-LINK can also be selected with the BS output. In addition, the simultaneous
output of 3G-SDI and HD-SDI is also possible.
■ Bidirectional HD-SDI trunk video line
The bi-directional HD-SDI (1.5G) trunk video line is standard equipment.
The bi-directional HD-SDI trunk video line can be used when the FA (Fiber Adaptor) at the camera head side is compatible.
Moreover, the trunk video (HD-QTV) from BS to the camera head also corresponds to asynchronous videos and asynchronous
embedded audio (4 ch). In addition, the trunk video can be used together with the conventional analog QTV (composite signal
trunk 2 ch).
■ Multi return video input
For the returned video input, inputs of four channels are possible with 3G/HD-SDI/SD-SDI automatic recognition. Each channel is
equipped with the frame synchronizer function; therefore, each channel corresponds to asynchronous signals.
The two-channel ACTIVE-THROUGH function is provided. Switching between the ACTIVE-THROUGH function and the fourchannel input function is possible by selecting in the BS menu.
* When the ACTIVE-THROUGH function is used, both BS and the camera head have the two return channel specification.
■ Audio Signal Embedded in each SDI Output (Embedded Audio Function)
Audio signals can be embedded in SDI signals of the main output, PM output, and WFM output. Audio signals can be embedded in
HD-SDI signals and SD-SDI signals.
■ Remote Control to Support Network
In addition to the conventional Ikegami serial command (ICCP), controls by the network connection are also available.
By setting up the system that corresponds to ARCNET, a wide variety of operation formats including panel assignments become
possible. In addition, it is also compatible with systems corresponding to Ethernet, which allows wide expandability.
■ Front/rear panel
Fulfillment of system interface function
The system interface function is more fulfilled when compared to the conventional systems, and thus the system operability has
improved.
This system uses the module that is common to that of the full rack size camera control unit [CCU-980] in the same series as this
BS.
The display system, operation system, input and output I/O are compatible; therefore, the system construction performance,
serviceability, and operability improved.
The front panel is equipped with the ID No. display function. Recognitions of the corresponding camera and the network ID
became easier.
The rotary switches for easier access to the BS menu is provided to the front panel.
BS-98 1409 VER1 (U) (E)
3
1.2
Specifications
1.2 Specifications
■ Rating and Performance
Output format (CCU / BS Common)
4
Camera head format:1080I/59.94 Y Pb Pr 4:2:2
-HDTV Signal output
1080I/59.94
-SDTV Signal output
525I/59.94
Y Pb Pr 4:2:2
Camera head format:1080P/23.98 2-3 pull down Y Pb Pr 4:2:2
-HDTV Signal output
1080P/23.98
2-3 pull down
1080P/23.98sF
segmented Frame
1080P/23.98
-SDTV Signal output
525I/59.94 (1080p23PD to Down Convert)
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Camera head format:1080P/29.97sF Y Pb Pr 4:2:2
-HDTV Signal output
1080P/29.97sF
segmented Frame
1080P/29.97
-SDTV Signal output
525I/59.94 (1080p29sF to Down Convert)
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Camera head format:720P/59.94 Y Pb Pr 4:2:2
-HDTV Signal output
720P/59.94
-SDTV Signal output
525I/59.94
Y Pb Pr 4:2:2
Camera head format:1080P/59.94 Y Pb Pr 4:2:2
-HDTV Signal output
1080P/59.94
1080P/59.94
1080I/59.94
-SDTV Signal output
525I/59.94
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
3G HD SDI
DUAL LINK
Camera head format:1080I/59.94 G B R 4:4:4
-HDTV Signal output
1080I/59.94
1080I/59.94
1080I/59.94
-SDTV Signal output
525I/59.94
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
3G HD SDI
DUAL LINK
Camera head format:1080P/23.98 2-3 pull down G B R 4:4:4
-HDTV Signal output
1080P/23.98
2-3 pull down
1080P/23.98
2-3 pull down
1080P/23.98
2-3 pull down
1080P/23.98sF
segmented Frame
1080P/23.98sF
segmented Frame
1080P/23.98sF
segmented Frame
1080P/23.98
1080P/23.98
1080P/23.98
-SDTV Signal output
525I/59.94 (1080p23PD to Down Convert)
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
3G HD SDI
DUAL LINK
Camera head format:1080P/29.97sF G B R 4:4:4
-HDTV Signal output
1080P/29.97sF
segmented Frame
1080P/29.97sF
segmented Frame
1080P/29.97sF
segmented Frame
1080P/29.97
1080P/29.97
1080P/29.97
-SDTV Signal output
525I/59.94 (1080p29sF to Down Convert)
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
BS-98 1409 VER1 (U) (E)
3G HD SDI
DUAL LINK
3G HD SDI
DUAL LINK
3G HD SDI
DUAL LINK
3G HD SDI
DUAL LINK
1.2
Camera head format:1080I/119.88 Y Pb Pr 4:2:2
-HDTV Signal output
1080I/119.88
1080I/119.88
1080I/59.94
-SDTV Signal output
525I/59.94
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Camera head format:1080I/50 Y Pb Pr 4:2:2
-HDTV Signal output
1080I/50
-SDTV Signal output
625I/50
Y Pb Pr 4:2:2
Camera head format:1080P/25sF Y Pb Pr 4:2:2
-HDTV Signal output
1080P/25sF
segmented Frame
1080P/25
-SDTV Signal output
625I/50 (1080p25sF to Down Convert)
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Camera head format:720P/50 Y Pb Pr 4:2:2
-HDTV Signal output
720P/50
-SDTV Signal output
625I/50
Y Pb Pr 4:2:2
Camera head format:1080P/50 Y Pb Pr 4:2:2
-HDTV Signal output
1080P/50
1080P/50
1080I/50
-SDTV Signal output
625I/50
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
3G HD SDI
DUAL LINK
Camera head format:1080I/50 G B R 4:4:4
-HDTV Signal output
1080I/50
1080I/50
1080I/50
-SDTV Signal output
625I/50
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
3G HD SDI
DUAL LINK
Camera head format:1080P/25sF G B R 4:4:4
-HDTV Signal output
1080P/25sF
segmented Frame
1080P/25sF
segmented Frame
1080P/25sF
segmented Frame
1080P/25
1080P/25
1080P/25
-SDTV Signal output
625I/50 (1080p25sF to Down Convert)
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
G B R 4:4:4
G B R 4:4:4
Y Pb Pr 4:2:2
3G HD SDI
DUAL LINK
Camera head format:1080I/100 Y Pb Pr 4:2:2
-HDTV Signal output
1080I/100
1080I/100
1080I/50
-SDTV Signal output
625I/50
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
3G HD SDI
DUAL LINK
Analog Frequency
characteristic
SDTV Signal output
(Downconverted from
1080I)
Audio output signal
(MIC1 / 2 OUT)
Specifications
3G HD SDI
DUAL LINK
3G HD SDI
DUAL LINK
Y signal
Less than 60 Hz
60 Hz to 4.5 MHz
4.5 MHz to 5 MHz
5 MHz or more
Falling characteristic
± 0.5dB within
± 1.0dB within
Falling characteristic
Less than 100 Hz
100Hz to 10kHz
10kHz or more
Falling characteristic
± 1.0dB within
Falling characteristic
BS-98 1409 VER1 (U) (E)
5
1.2
Specifications
Power
Environmental
condition
Power-supply voltage
AC100V/110V/117V/220V/240V ± 10%
Power consumption
CCU-980 self operation
BS-98 self operation
Using Workstation
temperature range
Operating temperature
CCU : 0℃ to +45℃
Storage temperature : -30℃ to + 60℃
Using Workstation
humidity range
It is non-condensing 30% to 90%
External dimensions
CCU-980
BS-98
Mass
CCU : About 28kg
Aplike estanda
Using Workstation
conditions
Approx. 110 VA
Approx. 80 VA
BS : 0 ℃ to +40℃
W483 × H133 × D454 (Not including protrusions)
W219 × H125 × D457 (Not including protrusions)
BS : About 9kg
EMC standards
FCC15 Subpart B Class A / EN55103-1, EN55103-2
Safety standard
EN60950-1
Quality control
ISO 9001 (JIS Z 9901)
Security Trade Control
Thawed relevant goods
Electrical environment
Normal living area
(I except the strong electric field, and magnetic field strength)
Apply standard
SMPTE 292M, SMPTE 425M, SMPTE 372M, SMPTE 259M
■ Input Signals
Item
6
Rating
GENLOCK signal
(HDTV/SDTV supported)
HDTV : PS
or
Tri-level sync
SDTV : BBS
or
BBS (w/10 FIELD ID)
SMPTE 318M
75Ω bridged connection
Return signal
(RETURN VIDEO)
3G-SDI/HD-SDI
SD-SDI selection
4 channels
75Ω single end input
Q-TV signal (Prompter)
Analog VBS
2 channels
HD Q-TV signal
(Prompter)
HD-SDI
INTERCOM signal
(ENG / PROD) 2 lines
Select from 4-wire/Clearcom/RTS
4-wire
Clearcom
RTS
2 channels
2 channels
2 channels
PGM (Program audio)
+4dBs or 0dBs
3 channels
TALLY signal
Red / Green / Yellow
Selected from the make contact / power supply
Y Pb Pr 4:2:2
1Vp-p
75Ω bridged connection
0.6Vp-p ± 6dB
1Vp-p
75Ω bridged connection
75Ω bridged connection
1Vp-p
1 channels
BS-98 1409 VER1 (U) (E)
75Ω single end input
75Ω single end input
0dBm
-15dBs
0dBm
600 Ω
200 Ω
200 Ω
600 Ω /10k Ω
1.2
Specifications
■ Output Signals
Item
Rating
Select from 3G-SDI/DUAL-LINK/HD-SDI
(SMPTE 425M, SMPTE 372M, SMPTE292M standard)
3 channels 6 outputs *1
HDTV signal
75 Ωoutput
SD-SDI
(SMPTE259M standard)
1 channel 2 outputs
75 Ωoutput
Synchronization signal
HDTV/SDTV selection
HDTV tri-level sync
SDTV
1 channel
0.6 Vp-p
2 Vp-p
75Ωoutput
Composite signal *2
VBS (ENC)
1 channel 2 outputs
Picture monitor (PM) signal
Select from HD-SDI/SD-SDI
Waveform monitor (WFM)
signal *4
Select from HD-SDI/SD-SDI
Intercom signal
(ENG/PROD) 2 lines
SD-SDI signal
*2
1 Vp-p
75 Ωoutput
2 channels *3
75 Ωoutput
1 channel
75 Ωoutput
Select from 4-wire/Clearcom/RTS
4-wire
Clearcom
RTS
2 channels
2 channels
2 channels
600Ω
200Ω
200Ω
MIC signal (Audio)
+4dBs or 0dBs
-18dBFS or -20dBFS
2 channels
2 channels
Tally signal (PM TALLY)
Red / Green / Yellow
3channel
(Analog)
(AES / EBU)
*1: Two channels are selectable from 3G-SDI/HD-SDI (HOUT module). One channel is selectable from 3G-SDI/HD-SDI/SD-SDI
(VOUT module).
*2: The signal is output only when the SDTV Option is implemented.
*3: One channel can be selected from PM/WFM.
*4: WFM output can be selected with PM-2. When WFM is set, the SDI output becomes the same one as OUT-3 output.
■ Camera Cable
Item
Rating
Standard cable
2SM-9.2-37.5
Cable for studio shooting
2SM-16-37.5
Cable configuration
2 single-mode silica glass fiber optic cables
(HEAD -> CCU/BS, CCU/BS -> HEAD one cable for each)
4 power cables (One cable has 37.5Ω/km.)
2 control cables (One cable has 113Ω/km.)
BS-98 1409 VER1 (U) (E)
7
8
BS-98 1409 VER1 (U) (E)
1.3
External Dimensions Diagram
1.3 External Dimensions Diagram
52.9±3
391.3±6
VOUT
SYNC OUT
HOUT
RETIN
1
1
M&R
SUB REF
REMOTE
DATA TRK
AES OUT
OUT3
1
2
OUT1
2
REF
2
PM WFM
MIC1 OUT
IF
MIC2 OUT
2
COMMUNICATION
TALLY OUT
1
OUT2
1
3
2
HD TRK
ENC
1
2
HD QTV IN
QTV IN
ARC
4
OCP/CCP
1
CSU/CCP
2
457±5
GENLOCK
TEMP
FAN
NORMAL
OPEN
SHORT
POWER OPTICAL LEVEL
HEAD BS
HEAD
BS
124.8±3
PRV
COM
PHONE
MIC
OPE
ON
OFF
PTT
LOCK
218.6±4
BS-98 1409 VER1 (U) (E)
9
2
NAME and FUNCTION
12
BS-98 1409 VER1 (U) (E)
2.1
BS-98 Front View
2.1 BS-98 Front View
This section explains the names and functions of the parts on the front of the BS-98.
BS-98 front display and operation unit
① ID display
⑦ GENLOCK indicator
⑧ TEMP indicator
⑨ FAN indicator
⑪ BS MAIN POWER
indicator
⑩ CABLE & OPTICALLEVEL
indicators
⑫ HEAD POWER
indicator
② TALLY indicators
③ INCOM COMMON/
PRIVATE switch
⑬ EMG/PM switch
⑭ CALL switch
⑮ MENU switch
⑤ INCOM PHONE knob
⑯ MENU control switch
④ INCOM MIC switch
⑥ INCOM
HEADSET connector
⑰ BS MAIN POWER switch
① ID display
ARCNET ID or the camera program number is displayed.
It can be set with "FUNCTION SETTING" item on ENGINEER (2/2) page of the BS menu.
- For ARCNET ID, a set value of 1 to 255 (decimal number ) is displayed in a hexadecimal number.
- For CAM PGM No., a set value of 1 to 99 is displayed.
② TALLY indicators
Indicators for Red TALLY, Green TALLY and Yellow TALLY.
R TALLY : Lights when the R TALLY signal is input to the TALLY IN connector on the rear of the BS. It also lights while the
CALL switch on the camera head or on any control panel (such as OCP, MCP, and RCP) is pressed.
G TALLY : Lights when the G TALLY signal is input to the TALLY IN connector on the rear of the BS.
Y TALLY : Lights when the Y TALLY signal is input to the TALLY IN connector on the rear of the BS.
③ INCOM COMMON/PRIVATE switch
Selects the intercom conversation mode.
COMM : Conversation among the camera head, BS, and system is enabled.
PRV
: Conversation between the camera head and BS is enabled.
④ INCOM MIC switch
Selects ON/OFF/PTT for the intercom headset microphone.
ON : Turns ON the intercom microphone.
OFF : Turns OFF the intercom microphone.
PTT : Turns ON the intercom microphone while this switch is pressed down. (Press To Talk)
⑤ INCOM PHONE knob
Controls the volume of the intercom receiver.
⑥ INCOM HEADSET connector
Connects the intercom headset. The connector type varies according to the regional and specifications.
BS-98 1409 VER1 (U) (E)
13
2.1
BS-98 Front View
⑦ GENLOCK indicator (green)
The indicator lights on when the proper synchronous coupling occurred to an external synchronizing signal that was input to BS.
⑧ TEMP indicator (red)
CAUTION:
Lights when the internal temperature of the BS increases abnormally.
When this indicator lights on, check that the ventilation hole on the front panel and the exhaust hole on the rear panel are not
covered or clogged with dust.
⑨ FAN ALARM indicator (red)
CAUTION:
The indicator lights on when the cooling fan inside of the BS POWER stops.
When the alarm is lit, immediately stop operating the equipment and turn off the power supply.
⑩ CABLE & OPTICAL LEVEL indicators
CABLE indicators
OPTICAL LEVEL indicators
· CABLE indicators
The indicator that displays the status of the Hybrid Fiber-Optic Camera Cable status.
NORMAL (green) : It lights up when the Hybrid Fiber-Optic Camera Cable is normal.
OPEN (red)
: It lights up when the Hybrid Fiber-Optic Camera Cable is not connected or is broken.
SHORT (red)
: It lights up when the power supply line of the Hybrid Fiber-Optic Camera Cable is short-circuited or
when the power contact pins are short-circuited by water drop, etc. The camera will not power up when
this indicator lights.
· OPTICAL LEVEL indicators
This is a light receiving indicator of the optical level. "HEAD" indicates the receiving condition at the camera head side, and
"BS" indicates the light receiving condition at the BS side.
Lighting Status
Light Reception Status
R Yl Gr Gr
● ○ ○ ○
OK
Light reception status is good.
R Yl Gr Gr
● ○ ○ ●
ATTENTION
The light reception level is low.
Although there is no problem with the reception of signals transmitted, cleaning the fiber
connector is may be required, unless attenuation is due to very long cable length.
R Yl Gr Gr
● ○ ● ●
WARNING
The light reception level is very low.
There might be a problem with the reception of signals transmitted. Immediate cleaning
the fiber connector is recommended.
R Yl Gr Gr
○ ● ● ●
NG
The light cannot be received.
There is a problem with the reception of signals transmitted. Cleaning the fiber connector
is required; or replace the cable since the camera cable might be broken.
( ○ : ON/ ● : OFF)
⑪ BS MAIN POWER indicator (green)
Lights when the BS main power is ON.
⑫ HEAD POWER indicator (orange)
Lights when power is supplied from the BS to the camera head.
⑬ EMG/PAGE switch
Two functions are assigned depending on the BS state.
-PAGE function When the BS power supply is on and is in the operating condition.
It works as a changeover switch for various information pages displayed for the output of the picture
monitor.
When the BS power supply is off (EMERGENCY function)
-EMG function
When the BS main power supply is turned on while the EMG switch is kept pressed, the SYSTEM
FORMAT of BS is forcibly switched to the general-purpose 1080I59.94 and 1080I50 and started up.
14
BS-98 1409 VER1 (U) (E)
2.1
BS-98 Front View
Note:
For example, when PM OUT FORMAT is set to 24p system or 3G HD-SDI, checking the further MENU operations on the monitor
becomes impossible without the monitor that corresponds to these formats.
In a such case, further recovery will be facilitated by rebooting the BS by using the EMG function.
- Switching is not possible beyond different frame rates of 59.94 Hz system and 50 Hz system.
- The 1920 x 1080 FORMAT of 59.94 Hz system boots in 1080I59.94. The 1920 x 1080 FORMAT of 50 Hz system boots in
1080I50. When the 1280 x 720 system FORMAT (720p59.94, 720p50) is set, no switching occurs.
- The output settings of OUT-1, OUT-2, OUT-3, and PM OUT are booted in 1080I59.94 YC 422 or 1080I50 YC 422.
- When the camera head FORMAT is different from the FORMAT that BS boots, the camera head side follows the BS format.
Therefore, the camera head side reboots. Thus, time is required until the communication and the image stabilize.
⑭ CALL switch
Only while this switch is pressed, the R TALLY indicators on the camera head and the control panel light.
Equipment that has a buzzer outputs buzzer sound.
⑮ MENU switch
This switch sets the on-screen BS menu operations for various settings.
Enables the BS menu display.
- OPE
- LOCK Disables the BS menu display function. The MENU control switch ⑯ becomes disabled.
When the switch is changed from OPE to OFF while the BS menu is displayed, the menu ends.
⑯ MENU control switch
When this switch is kept pressed for approx. 3 seconds while the MENU switch ⑮ is at the OPE side, the BS menu is displayed
at the PM OUT output. When the dial is turned, the cursor moves. When the switch is pressed, the selected item is finalized.
⑰ BS MAIN POWER switch
This is the main AC power supply switch of the base station.
GENLOCK
TEMP
FAN
GENLOCK
TEMP
FAN
NORMAL
OPEN
SHORT
NORMAL
OPEN
SHORT
POWER OPTICAL LEVEL
POWER OPTICAL LEVEL
HEAD BS
HEAD BS
HEAD
HEAD
BS
BS
PRV
PRV
COM
COM
PHONE
MIC
PHONE
OPE
MIC
ON
OFF
PTT
ON
OFF
PTT
LOCK
OPE
LOCK
⑲ Fuse
⑱ Front cover
Top
: camera head power transmission
Lower : BS AC Power input
⑱ Front cover
Protection cover on the front of the BS.
How to open the front cover
When opening the front cover, loosen the fixing screws at the upper and lower right corners of the cover. These screws are dropoff preventive type.
When removing the cover, hold the upper and lower latching pins and remove the cover to the near side.
Follow the removing procedure in the inverse order when attaching the cover. At this time, be very careful not to pinch the
optical fiber cable (yellow two cables).
⑲ Fuse
When checking or replacing the glass tube fuse for the equipment protection, open the front cover.
Fuse of the camera head power transmission (upper)
Fuse to be used 250V T2A (rating) ("T" in the rating indicates a time lag fuse.)
Fuse of BS AC input power supply (lower)
100V-117V AC input voltage : 250V T6.3A (rating)
220V-240V AC input voltage : 250V T3.15A (rating) ("T" in the rating indicates a time lag fuse.)
BS-98 1409 VER1 (U) (E)
15
2.1
BS-98 Front View
BS-98 Front View With the Front Cover Off
② OPT module
① RET module
④ SPRC module
③ HPRC
module
⑥ IO module
⑤ PLS module
Note:
④ SPRC module is optional.
When the SPRC module is not mounted, "OUT-3" output of the VOUT module on the rear side and "PM OUT" SD-SDI signal cannot
be selected.
At the same time, "ENC OUT" (analog VBS signal) is not output.
① RET module
The detection status of the RETURN signal and the mode are indicated.
IN1
Light up when the input signal of RETURN channel#1
has been detected.
THRU Lights up when It has set the Active loop through.
IN2
Light up when the input signal of RETURN channel#2
has been detected.
IN3
Light up when the input signal of RETURN channel#3
has been detected.
THRU Lights up when It has set the Active loop through.
IN4
Light up when the input signal of RETURN channel#4
has been detected.
USB connector for maintenance and service.
Note:
The active loop through output executes the through output only when the equipment power is on.
16
BS-98 1409 VER1 (U) (E)
2.1
BS-98 Front View
② OPT module
It displays the information related to the transmission between the camera head and BS/CCU.
720P
Lights up when format the 720p.
P(sF)
Lights up when format the psF.
3G
Light up when the 3G transmission mode.
GBR444 Light up when the 4:4:4 Mode.
CAUTION:
The OPT module is connected with the BS body via the optical cable (yellow). Do not disconnect the cable at any timing other than
replacing the module.
When the cable is disconnected forcibly, damaging and/or breakage of the cable may occur.
③ HPRC module
It displays the information related to the frame rate and bi-directional HDTV-TRUNK.
59Hz
Lights up when format the Frame rate
59.94Hz.
50Hz
Lights up when format the Frame rate
50.00Hz.
29Hz
Lights up when format the Frame rate
29.97Hz.
25Hz
Lights up when format the Frame rate
25.00Hz.
23Hz
Lights up when format the Frame rate
23.98Hz.
QTV IN
Lights up when it detects a HDTV
QTV input signal.
TRK OUT Light up when the HDTV TRUNK
output mode .
Note:
HD QTV
: Transmits HD-SDI signals from BS/CCU to the camera head.
HD TRUNK : Transmits HD-SDI signals from the camera head to BS/CCU.
In order to use the above functions, a fiber adaptor that corresponds to the 3G transmission is required.
BS-98 1409 VER1 (U) (E)
17
2.2
BS-98 Rear View
④ PLS module
It displays the information related to synchronization between the camera head and BS and the external reference signals.
APC
Phase lock and Camera head is turned on when
normal.
G.L
Lights up when It has Synchronous coupling
normally to External reference signal .
REF IN Light up when it detects the input of an
external reference signal.
Note:
APC : Auto Phase Control
Function used to automatically adjust the vertical and horizontal phases between the camera head and BS/CCU.
⑤ IO module
This module indicates the setting status of the FIBER SINGLE mode.
FIBER SINGLE Lights up when it is set to ON the
FIBER SINGLE mode in the MENU.
Note:
What is the FIBER SINGLE mode ?
The extendable transmission distance between the camera head and CCU/BS is generally determined by the power transmission
capability of CCU/BS and the attenuation of optical level. When the power transmission capability is insufficient, the power is
supplied from the camera head side by using local power supply, so the limitation of the operation due to insufficient power supply
can be avoided. When the FIBER SINGLE mode is turned on, power supply from CCU/BS stops; however, the bidirectional optical
transmission is operable as usual operations.
For the power supply method from local power supply source at the camera head side and the setting method of the FIBER SINGLE
mode, refer to the instruction manual of each camera. If a long-distance optical transmission device made by a third party is used,
check the compatibility of the device.
18
BS-98 1409 VER1 (U) (E)
2.2
BS-98 Rear View
2.2 BS-98 Rear View
This section explains the names and functions of the parts on the rear of the BS-98.
① CAMERA connector
⑪ SUB REF connector
③ DATA TRK connector
④ REMOTE connector
⑥ SYNC OUT
connector
⑦ AES OUT
connector
⑤ COMMUNICATION connector
⑩ AC Power inlet
⑨ IF connector
② MIC OUT connector
⑧ TALLY OUT connector
Reference:
For model names of connectors and details of assignments, refer to "4.6 Connector for External Connection".
① CAMERA connector
Optical fiber composite camera cable, This connector is to connect the camera head and the BS.
② MIC OUT connectors
Output the audio signals that are input to the MIC IN connectors on the camera head. (2 channels analog audio)
③ DATA TRK connector
This is a connector for RS-422 communication with the camera head. (Channel #1)
④ REMOTE connector
This is a connector used to externally control the microphone gain of the camera head.
⑤ COMMUNICATION connector
This connector is used for a connection with an external system.
Input/output of Intercom system, program audio input, and TALLY control input are assigned.
⑥ SYNC OUT connector
The signal for synchronization of the external equipment is output. In "SYNC OUT" setting under "ENGINEER (1/2)" ->
"OUTPUT FORMAT" in BS menu, HDTV Tri-Level sync signal output or SDTV synchronizing signal output can be selected.
Note) SDTV synchronizing signal is not the BBS.
⑦ AES OUT connector
It is an output connector of the digital audio signal (75Ω output). The signal is conformable to the AES/EBU format.
BS-98 1409 VER1 (U) (E)
19
2.2
BS-98 Rear View
⑧ TALLY OUT connector
TALLY OUT signals that are used for external control device.
⑨ IF connector
DATA TRUNK #2, Camera head power ON/OFF indicator output, PREVIEW output, and other functions are assigned.
(In order to use the Channel # 2, the camera head side is also need to be addressed)
⑩ AC power inlet
This inlet is used to connect the AC cable to the BS and to operate the AC power supply.
* The input voltage ranges are 100 to 120 VAC +/- 10% and 220 to 240 VAC +/- 10%.
⑪ SUB REF connector (SUB Rreference)
When the output format is 1080P/23.98PD (2-3 pull-down), 1080P/23.98, and 1080P/23.98sF (segment frame), the 23.98P signal
and the 2-3 pull-down signal phases can be adjusted by inputting the following signals.
● When setting one unit of BS-98 as a master and synchronization other 2-3 pull-down signals of
BS-98 or CCU-980 phases
Input the HDTV Tri-level sync signal with 10 FIELD ID, which is output from the SYNC OUT connector of the master BS-98,
to the SUB REF connector of other BS/CCU.
● When synchronization 23.98P signal and 2-3 pull-down signal to the phase of reference signal
Input the synchronizing signal of the 23.98P format. However, when inputting the synchronizing signal in 59.94I format to the
BS/CCU REF connector, phases of the synchronizing signals in the 23.98/P format and in the 59.94I format must match to each
other.)
Reference:
Refer to "3.2 GENLOCK System" for details.
20
BS-98 1409 VER1 (U) (E)
2.2
BS-98 Rear View
Modules on the Rear of the BS-98
Modules on the rear are also of slot type and can be removed/inserted as well as the modules on the front.
④ VOUT ③ HOUT
module
module
② RET̲IN ① MPU&REF
module
module
① MPU&REF Module
1. REF connector
1
It inputs the reference signal (HDTV PS/S or SDTV VBS/BBS) from the external source. It is also
possible to input the signals, of which the 10 field ID signal conformable to SMPTE318M is added,
to VBS/BBS.
Bridge connection is possible.
2. Ethernet RJ45 (8P8C) connector
This is a connector to be used for connecting with the system corresponding to Ethernet.
2
3. ARCNET connector
3
This is a connector for ARCNET. It is connected to CP HUB (option) by the coaxial cable.
Refer to the Instruction manual of CP HUB to be used for details.
CAUTION:
4
5
- Use the F-head type conversion plug for connection. In addition, use 75Ω type coaxial cables and
terminators.
- When the connector contacts the housing, failures may be caused. Pay close attention when
handling.
- When using the F-head type conversion plug, cover with an insulation cover or other item.
4. OCP/CCP connector
Connect with CP cable and OCP.
5. CSU/CCP connector
Connect with CP cable and CSU.
BS-98 1409 VER1 (U) (E)
21
2.2
BS-98 Rear View
② RET IN Module
1 to 4. RETURN IN connector
Input the return video signal to the camera head.
1
It corresponds to inputs of four lines. It automatically recognize three rate signals of 3G-SDI/HDSDI/SD-SDI.
2
When ACTIVE-THROUGH is turned on from the CCU/BS menu, CH2 and CH4 become the output
connectors. A signal input to CH1 is output to CH2, and a signal input to CH3 is output to CH4.
3
*When the ACTIVE-THROUGH function is used, both BS/CCU and the camera head apply return
2 channel specification.
NOTE:
4
5
The format of input signal is automatically recognized. When an asynchronous signal and/or a signal
with a different frame rate is input, FS (Frame Synchronizer) automatically turns on.
From the CCU/BS menu, FS can be manually set separately for each of four channels. FS is not
automatically turned off when a signal that does not require FS is input. Set FS to OFF from the
menu.
5. QTV IN connector
It inputs the QTV signal (prompter signal) to be sent to the camera head.
It corresponds to the analog VBS signal two-line input and has the 75Ω single-end terminal.
* The number of QTV output lines at the camera head side varies depending on the model and
specifications.
③ HOUT Module
1. OUT1 connector
1
It outputs SDI signal in two rates of 3G/HD-SDI. One line and two outputs.
When DUAL LINK format is selected in "OUTPUT FORMAT" in the menu, LINK-A signal is
output.
2. OUT2 connector
2
It outputs SDI signal in two rates of 3G/HD-SDI. One line and two outputs.
When DUAL LINK format is selected in "OUTPUT FORMAT" in the menu, LINK-B signal is
output.
3. HD TRUNK OUT connector
It outputs the HD-SDI TRUNK signal from the camera head. 1 line and 1 output.
HD-SDI signal is output.
4. HD QTV IN connector
3
Input the HD-SDI QTV signal to be sent to the camera head. 1 line and 1 input.
NOTE:
4
22
- To use the HD TRUNK and HD QTV functions, it is necessary that the Fiber Adaptor at the camera
head side corresponds to the 3G transmission (HDK-79EX series, FA-79/A, and FA-55 do not
correspond to the 3G transmission).
- The HD TRUNK function is disabled when the 3G transmission format is selected for the SYSTEM
FORMAT.
BS-98 1409 VER1 (U) (E)
2.2
BS-98 Rear View
④ VOUT Module
1. OUT3 connector
1
It outputs SDI signals in three rates of 3G/HD-SDI/SD-SDI. 1 line and 2 outputs.
SD-SDI is the SMPTE259M 270 Mbps signal.
2. PM-1 OUT connector
2
It outputs SDI signals in three rates of 3G/HD-SDI/SD-SDI for the picture monitor. 1 line and 1
outputs.
SD-SDI is the SMPTE259M 270 Mbps signal.
CCU/BS menu characters and PM menu characters that indicate various data are superimposed in
the image.
3. PM-2/WFM OUT connector
3
4
The following signals are output by selecting "OUTPUT FORMAT" -> "PM-2/WFM" on the menu.
- PM HD-SDI
It outputs SDI signal that is the same as PM-1 OUT.
It outputs SDI signals in two rates of 3G/HD-SDI for the picture monitor. 1 line and 1 output.
CCU/BS menu characters and PM characters that indicate various data are superimposed in the
image.
- PM SD-SDI
SD-SDI signal for the picture monitor is output. 1 line and 1 output.
CCU/BS menu characters and PM characters that indicate various data are superimposed in the
image.
- WFM (OUT-3)
The signal that is the same as OUTPUT FORMAT set at OUT-3 is output. 1 line and 1 output.
4. ENC OUT connector
Analog composite (ENC) signal is output. 1 line and 2 outputs.
CAUTION:
- When SDTV Option (SPRC module) is not mounted, the SD-SDI output and the ENC output become disabled.
- CCU/BS menu characters are superimposed in the SDTV output (SD-SDI and ENC OUT).
BS-98 1409 VER1 (U) (E)
23
24
BS-98 1409 VER1 (U) (E)
FORMATS and GENLOCK
3
26
BS-98 1409 VER1 (U) (E)
3.1 HDTV Format
3.1 HDTV Format
This section explains the HDTV formats displayed on the BS menu and the self-diagnosis with some examples.
１０８０ Ｉ ５９．３Ｇ
Interface (3G: 3G-SDI / No: HD-SDI)
Frame frequencies (59.94Hz in this case)
Scanning mode (I: interlace/P: progressive)
Number of effective scanning lines (1080 lines in this case)
１０８０
Ｐ
２３．ＰＤ
2-3 pull down
１０８０
Ｐ
２９．ＳＦ
Segmented frame
■ 2-3 Pull Down
2-3 pull down is a method of converting a 24-frame (24P) video into a 60-field (60I) video.
This method has been used by Telecine, which converts film movies to television signals since early times, and connecting to many
kinds of HDTV systems is possible as the 1080p23.98PD signal can be handled as the 1080i59.94 signals.
1 frame
2
3
4
1
2
3
4
24P
60I
1-A
1-B
1 frame
2-A
2-B
2
2-A
3-B
3
3-A
4-B
4
4-A
4-B
5
10 fields
(A: odd field, B: even field)
BS-98 1409 VER1 (U) (E)
27
3.1
HDTV Format
■ Segmented Frame
Segmented frame is a method for converting a progressive video separated for 1 line each into an interlaced video.
1/24 sec
24p
Frame #1
Frame #2
1/48 sec
24psF
Segment A
Segment B
Segment A
Segment B
1st Field
2nd Field
1st Field
2nd Field
Odd Lines
Even Lines
Odd Lines
Even Lines
It has been described for the sake of convenience, 23.976 is 24 and 47.952 is 48.
The feature of the segment frame is that there is no movement in the first frame (Segment A) and the second frame (Segment B).
When these two frames are synthesized, one progressive signal can be created.
PsF (Progressive segmented Frame) method has been widely used from the time when the 24P format appeared. That is because
this method enables to create the conventional interlace equipment without making a large difference.
In addition, in recent years, there are more cases that this method is used for the time lapse video effect in television broadcasting,
as the 1080PsF29.97 signals can be used as 1080i59.94, and the 1080PsF25 signals can be used as 1080i50.
28
BS-98 1409 VER1 (U) (E)
3.1 HDTV Format
The following section indicates the lists of HDTV formats, output formats, and signal formats indicated on the BS/CCU menu and
the self-diagnosis display screen (Diagnostic Information).
Menu screen notation
1080I59
Format
1920 x 1080
SDI signal
interlace
60/M
1080i59.94
1.485/M Gbps
Standard
422
274M/292M
1080P23PD
1920 x 1080
2-3 pulldown
24/M
1080i59.94
1.485/M Gbps
422
274M/292M
1080P23SF
1920 x 1080
progressive(sF)
24/M
1080psF23.98
1.485/M Gbps
422
274M/292M
1080P23
1920 x 1080
progressive
24/M
1080p23.98
1.485/M Gbps
422
274M/292M
1080P29SF
1920 x 1080
progressive(sF)
30/M
1080psF29.97
1.485/M Gbps
422
PR211/292M
1080P29
1920 x 1080
progressive
30/M
1080p29.97
1.485/M Gbps
422
274M/292M
720P59
1280 x 720
progressive
60/M
720p59.94
1.485/M Gbps
422
296M/292M
1080I50
1920 x 1080
interlace
50
1080i50
1.485 Gbps
422
274M/292M
1080P25SF
1920 x 1080
progressive(sF)
25
1080psF25
1.485 Gbps
422
PR211/292M
1080P25
1920 x 1080
progressive
25
1080p25
1.485 Gbps
422
274M/292M
720P50
1280 x 720
progressive
50
720p50
1.485 Gbps
422
296M/292M
2.970/M Gbps
422
274M/425M
1.485/M Gbps
422
274M/372M
2.970/M Gbps
444
274M/425M
1.485/M Gbps
444
274M/372M
2.970/M Gbps
444
274M/425M
2x
1.485/M Gbps
444
274M/372M
2.970/M Gbps
444
PR211/425M
2x
1.485/M Gbps
444
PR211/372M
2.970/M Gbps
444
274M/425M
2x
1.485/M Gbps
444
274M/372M
2.970/M Gbps
444
PR211/425M
2x
1.485/M Gbps
444
PR211/372M
2.970/M Gbps
444
274M/425M
2x
1.485/M Gbps
444
274M/372M
2.970/M Gbps
422
EVS
1.485/M Gbps
422
EVS
2.970 Gbps
422
274M/425M
2x
1.485 Gbps
422
274M/372M
2.970 Gbps
444
274M/425M
2x
1.485 Gbps
444
274M/372M
2.970 Gbps
444
PR211/425M
2x
1.485 Gbps
444
PR211/372M
2.970 Gbps
444
274M/425M
2x
1.485 Gbps
444
274M/372M
1080P59
3G-SDI
1920 x 1080
progressive
60/M
1080p59.94
1080P59
DUAL-LINK
1920 x 1080
progressive
60/M
1080p59.94
1080I59
3G-SDI
1920 x 1080
interlace
60/M
1080i59.94
1080I59
DUAL-LINK
1920 x 1080
interlace
60/M
1080i59.94
1080P23PD
3G-SDI
1920 x 1080
2-3 pulldown
24/M
1080i59.94
1080P23PD
DUAL-LINK
1920 x 1080
2-3 pulldown
24/M
1080i59.94
1080P23SF
3G-SDI
1920 x 1080
progressive(sF)
24/M
1080psF23.98
1080P23SF
DUAL-LINK
1920 x 1080
progressive(sF)
24/M
1080psF23.98
1080P23
3G-SDI
1920 x 1080
progressive
24/M
1080p23.98
1080P23
DUAL-LINK
1920 x 1080
progressive
24/M
1080p23.98
1080P29SF
3G-SDI
1920 x 1080
progressive(sF)
30/M
1080psF29.97
1080P29SF
DUAL-LINK
1920 x 1080
progressive(sF)
30/M
1080psF29.97
1080P29
3G-SDI
1920 x 1080
progressive
30/M
1080p29.97
1080P29
DUAL-LINK
1920 x 1080
progressive
30/M
1080p29.97
1080I119
3G-SDI
1920 x 1080
interlace
120/M
1080i119.88
1080I119
DUAL-LINK
1920 x 1080
interlace
120/M
1080i119.88
1080P50
3G-SDI
1920 x 1080
progressive
50
1080p50
1080P50
DUAL-LINK
1920 x 1080
progressive
50
1080p50
1080I50
3G-SDI
1920 x 1080
interlace
50
1080i50
1080I50
DUAL-LINK
1920 x 1080
interlace
50
1080i50
1080P25SF
3G-SDI
1920 x 1080
progressive(sF)
25
1080psF25
1080P25SF
DUAL-LINK
1920 x 1080
progressive(sF)
25
1080psF25
1080P25
3G-SDI
1920 x 1080
progressive
25
1080p25
1080P25
DUAL-LINK
1920 x 1080
progressive
25
1080p25
1080I100
3G-SDI
1920 x 1080
interlace
100
1080i100
1080I100
DUAL-LINK
1920 x 1080
interlace
100
1080i119.88
2x
2x
2x
2x
2.970 Gbps
422
EVS
1.485 Gbps
422
EVS
sF : segmented Frame
/M : I represent the /1.001
EVS : Outputs that correspond to the video servers of EVS Broadcast Equipment (TM).
In order to use above output formats, it is prerequisite that the camera head to be connected is a compatible type.
When the camera head that is not compatible is connected, the connected camera head cannot be selected.
BS-98 1409 VER1 (U) (E)
29
3.2
GENLOCK System
3.2 GENLOCK System
This section explains input/output connectors and connection examples of the GENLOCK system for this product.
Input Connectors
REF connectors and SUB REF connectors are explained here.
The phase of output signals can be synchronized with the reference signals input to the REF connectors and SUB REF connectors.
■ REF connectors (Loop-through)
Three types of signals below can be input to the REF connectors.
① HDTV PS/S (Tri-level sync)
② SDTV VBS/BBS (NTSC / PAL)
③ BBS + 10 FIELD ID (SMPTE 318M compliant)
[There are cases that 10 FIELD ID is set as an option for the synchronizing signal generator (sync generator).]
■ SUB REF connectors (Loop-through)
When the output format is 1080P/23.98PD (2-3 pulldown), 1080P/23.98, or 1080P/23.98sF (segment frame), the phase of 23.98P and
2-3 pulldown signals can be synchronized by inputting the following signals.
s 7HEN THE PHASE OF PULLDOWN SIGNAL OF ANOTHER ##5"3 IS SYNCHRONIZED BY USING A ##5 BS-98 as master
Input the HDTV 3 value synchronizing signal with 10 FIELD ID that is output from the SYNC OUT connector of master CCU980/BS-98, to the SUB REF connector of the slave CCU/BS.
s 7HEN THE PHASE OF 0 AND PULLDOWN SIGNALS IS SYNCHRONIZED WITH THE REFERENCE SIGNALS
Input the 23.98P format synchronizing signal to the SUB REF connector. However, when the synchronizing signal in the 59.94I
format is input to the CCU/BS REF connector, phases of the synchronizing signals in the 23.98/P format and in the 59.94I format
must match to each other.)
Output Connectors
SYNC OUT connector and ENC OUT connectors are explained here.
■ SYNC OUT connector
SYNC OUT connector outputs synchronization signals. The format to be selected varies depending on the setting of SYSTEM
FORMAT. (Select a format from the CCU/BS menu.)
SYSTEM FORMAT
Format that can be selected in the SYNC OUT of OUTPUT FORMAT
1080P59
1080P59 / 1080I59 / SDTV
1080I59
1080I59 / SDTV
1080P23PD
1080I59 / 1080P23 / 1080P23SF / SDTV
1080P29SF
1080I59 / 1080P29 / SDTV
1080I119
1080I59 / SDTV
720P59
720P59 / SDTV
1080P50
1080P50 / 1080I50 / SDTV
1080I50
1080I50 / SDTV
1080P25SF
1080I50 / 1080P25 / SDTV
1080I100
1080I50 / SDTV
720P50
720P50 / SDTV
In addition, when the 1080P23PD format is selected, it is possible to select on the menu whether or not 2H pulse is added at every
10 FIELD of 1080I59 (it is not the same as the 10 FIELD ID specified in SMPTE 318M; however, it is called as "10 FIELD ID" as
well here).
30
BS-98 1409 VER1 (U) (E)
3.2 GENLOCK System
■ ENC OUT connector (SDTV options when mounted)
10 FIELD ID can be added to the ENC signal. (The 10 FIELD ID described here indicates the ID specified by SMPTE 318M.)
Note:
When the format of the camera head is 1080I/59.94 (2-3 pulldown), the phase of 2-3 pulldown signal needs to be synchronized even if
the 2-3 pulldown signal is not used for the CCU/BS output since the 2-3 pulldown signal is transmit and received between the camera
head and the CCU/BS.
■ Operating configurations
● When format conversion is not performed
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
ＲＥＦ
CCU or BS #1
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
Ａ
SUB REF
Ｂ
ＲＥＦ
Signal generator
CCU or BS #2
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
ＲＥＦ
75Ω termination
CCU or BS #3
Condition of signals output by the signal generator in this case
A: HDTV tri-level sync signals whose format is the same as the camera head or NTSC
BBS
Example) SYSTEM FORMAT of BS / CCU : 1080i59.94
Format of the camera head
: 1080i59.94
Synchronization signal input to the REF connector
HDTV Tri-level sync 1080i59.94 or SDTV (NTSC) BBS
BS-98 1409 VER1 (U) (E)
31
3.2
GENLOCK System
● When format conversion is performed
The following four patterns use 1080I/59.94 or 1080P/23.98 as a format of the camera head.
In addition, 1080P/23.98 is used as the output of the format conversion.
- Pattern 1
The case that NTSC BBS + 10 FIELD ID (SMPTE 318M-compliant) signals can be supplied from the signal generator
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
ＲＥＦ
CCU or BS #1
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
Ａ
SUB REF
Ｂ
ＲＥＦ
Signal generator
CCU or BS #2
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
ＲＥＦ
75Ω termination
CCU or BS #3
Condition of signals output by the signal generator in this case
A: NTSC BBS + 10 FIELD ID (SMPTE 318M-compliant)
32
BS-98 1409 VER1 (U) (E)
3.2 GENLOCK System
- Pattern 2
One of BSs is placed as master when the signal generator is not used.
(*)
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
ＲＥＦ
CCU or BS #1 (master)
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
ＲＥＦ
CCU or BS #2 (slave)
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
ＲＥＦ
75Ω termination
CCU or BS #3 (slave)
* In that case, add 10 FIELD ID signal (SMPTE 318M compatible) to the ENC signal output of the master equipment.
[Setting]
SD-10 FIELD ID SIG" item under "OUTPUT FORMAT" of "ENGINEER (1/2)" in the CCU/BS menu to ON.
BS-98 1409 VER1 (U) (E)
33
3.2
GENLOCK System
- Pattern 3
The case that synchronization signals of two types of formats can be supplied from the signal generator
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
ＲＥＦ
CCU or BS #1
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
Ａ
SUB REF
Ｂ
ＲＥＦ
Signal generator
CCU or BS #2
ＥＮＣ ＯＵＴ
ＳＹＮＣ ＯＵＴ
SUB REF
75Ω termination
ＲＥＦ
75Ω termination
CCU or BS #3
Condition of signals output by the signal generator in this case
A: HDTV Tri-level sync of 1080I/59.94 format or NTSC BBS
B: HDTV Tri-level sync of 1080P/23.98 format
(However, the 10-field interval for 1080I/59.94 format needs to be synchronized
with the 4-frame interval for 1080P/23.98 format.)
34
BS-98 1409 VER1 (U) (E)
EQUIPMENT
CONNECTIONS
4
36
BS-98 1409 VER1 (U) (E)
4.1
Preparation
4.1 Preparation
Product Use Environment
Please read THE SAFETY PRECAUTIONS in the beginning of this document and follow the precautions for use.
Make Sure the Power Switch is OFF
Please make sure that the power switch is "OFF" before connecting this product and peripheral equipment such as the camera head.
BS front view
MAIN
POWER
switch
Camera right view
ACTIVE
STANDBY
BS/CCU
POWER
switch
OFF
EXT
* HDK-97A (+ FA-97) is used as an example of
the camera head for explanation.
Refer to the instructions accompanying the
camera head to be used for the locations of
the POWER switches and switch settings.
POWER
At first, set the INCOM PHONE knob to the minimum.
CAUTION:
Do not set the volume of the INCOM PHONE knob suddenly around to the maximum when connecting the headset to the INCOM
connector. Maximizing the intercom volume while putting the headset to an ear may rupture and damage the eardrum. Also, excess
sound pressure may cause a hearing loss.
INCOM PHONE knob
Set the volume level to the
minimum at first.
INCOM connector
Head set
BS-98 1409 VER1 (U) (E)
37
4.2
Power Supply
4.2 Power Supply
This section explains how to power supply to the BS and supply power from the BS to the camera head.
1
2
3
4
Make sure the BS MAIN POWER switch of the BS is "OFF".
Connect the AC cable to the AC INPUT connector on the rear of the BS.
Insert the AC plug into the power outlet.
Connect a camera cable to the CAMERA connector on the rear of the BS, and connect the other end of the
camera cable to the camera head.
Refer to "4.3 BS and Camera Head Connection" for how to connect the camera cable to the camera head.
BS rear view
Optical fiber complex
Camera cable
To the camera
AC INPUT connector
AC cable
Power outlet
Two methods of power supply to the camera head are available with this configuration.
a) To control the power ON/OFF from the BS (turned ON / OFF at the main power of the BS)
b) To control the power ON/OFF from the OCP (remote control)
Note:
Function will change by the control panel (OCP) to be used.
38
BS-98 1409 VER1 (U) (E)
4.2
Power Supply
■ To Control Power ON/OFF from BS
You can control the power ON/OFF of the camera head from the BS.
1
Set the [BS MAIN POWER switch] on the front of the BS to "ON".
This turns on the power of the BS and lights the BS MAIN POWER indicator.
In addition, the status of the camera cable connection between the camera head and the BS is automatically checked.
When the connection is judged normal, [NORMAL] green LED lights up.
When the cable is defective, or when the connection is failed, [OPEN]/[SHORT] red LED lights up.
When the power is supplied to the camera head, the HEAD POWER indicator lights up.
BS-98 front view
HEAD POWER indicator
BS MAIN POWER indicator
BS MAIN POWER switch
CAUTION:
To turn on the BS MAIN POWER switch just after the switch is turned off, wait one or more seconds before you turn on the power.
Repeating the on/off operation within one second activates protector for equipment protection.
When the protector is activated, turn on the BS MAIN POWER switch after five or more seconds later.
BS-98 1409 VER1 (U) (E)
39
4.2
Power Supply
■ To Control Power ON/OFF from OCP (Remote Control)
This section describes an example of a case of using the OCP-200.
1
2
Set the [BS MAIN POWER switch] on the front of the BS to "ON".
Set the [CAM POWER switch] on the OCP to "ON".
Power is supplied to the camera head.
OCP-200
OCP-200
OCP-200
CAM PWR
switch
Note:
When the CAM POWER switch on the OCP is turned "ON/OFF", only power supply to the camera head is turned "ON/OFF".
The BS main power is not controlled.
40
BS-98 1409 VER1 (U) (E)
4.3
BS and Camera Head Connection
4.3 BS and Camera Head Connection
This section explains how to connect the BS to the camera.
Connect the CAMERA connector on the rear of the BS to the CAMERA connector on the camera head via a camera
cable.
Camera head
* HDK-97A (+ FA-97) is used as an example of the camera for explanation.
Refer to the instructions accompanying the camera head to be used
for the location of the CAMERA connector.
REAR TALLY
OFF
ACT
INCOM1
INCOM SEL
INC1
FRONT
3
REAR
CALL
INC2
FRONT
4
3
2
4
INCOM2
2
1
1
INCOM
INCOM
ON
OFF
PTT
PGM1
MIC
ON
OFF
PTT
MIC
PROD
BOTH
ENG
PGM2
ENG
PROD
BOTH
ENG
INCOM
PGM1
PGM2
PROD
Q-TV/GL
I/O
CAMERA connector
EARPHONE
MON
SDI OUT
MON SDI
+12V
DC OUT
+48V
OFF
CAMERA connector
MIC-1
MIC-2
DC IN
BS-98 rear view
Optical fiber complex
Camera cable
CAUTION:
- The camera cable has a plug on one end and a jack on the other end. Make sure the difference before connection.
- Do not forcibly bend the camera cable nor apply excessive force to the camera cable.
- Refer to the instructions accompanying the cable or camera head to be used for how to handle the camera cable.
BS-98 1409 VER1 (U) (E)
41
4.4
System Setup Diagram
4.4 System Setup Diagram
MIC-1
MIC-2
HDK-97A (FA-97)
*HDK-97A (FA-97) is used as
an example of the camera for
explanation.
Camera Cable
Max. 1000m
Headset
(ENG/PROD)
Headset
(ENG/PROD)
BS-98
3G/HD-SDI
SD-SDI (option)
3G/HD-SDI
SD-SDI (option)
PM
WFM
CSU-110 with SDI SELECT module (optional)
MCP Cable
Max. 30m
CP Cable Max. 100m
CP Cable Max. 300m
PM (SDI)
PM (SDI)
PM
OCP
MCP
MCP
Multiple Camera Operation
* When the OCP-200 is used, the maximum CP cable length is 80m.
42
BS-98 1409 VER1 (U) (E)
4.4 System Setup Diagram
■ Network Operation
MIC-1
MIC-2
HDK-97A (FA-97)
*HDK-97A (FA-97) is used as
an example of the camera for
explanation.
BS-98
Camera Cable
Max. 1000m
Headset
(ENG/PROD)
Headset
(ENG/PROD)
※1
3G/HD-SDI
SD-SDI (option)
3G/HD-SDI
SD-SDI (option)
PM
WFM
※2
Coaxial cable
(Network command)
PM (SDI)
ＣＰＨ-２００
CPH-200
※2
CP Cable
(Network command)
CSU-110
with SDI SELECT module (optional)
OCP-200
OCP-200
ＭＣＰ
Cable
OCP-200
PM (SDI)
ＭＣＰ-２００
ＰＭ
DC IN
+12V
OＣＰ-２００
※3
*1 Network ID of the BS set from the BS menu.
*2 For the maximum and minimum extension length of the cables, refer to "BSH-200/CPH-200 Setup Manual".
*3 For network operation, commands can be selected from an OCP, MCP, or CPH. For video signals, the operating configuration to
select the signals from the CSU-110 is also accepted.
However, an external power supply (DC +12V) is required when the MCP-200 is used and the extension length of the cables is
long.
BS-98 1409 VER1 (U) (E)
43
4.5
Operating Systems
4.5 Operating Systems
■ ARCNET Connection (Basic bus connection)
This connection configuration is available only for network-enabled CCU/BS such as the CCU-980 / BS-98.
BS-2
OP8
OP7
OP6
OP5
CPH-200
OP4
OP3
ARC1
ARC
OP2
ARC
OP1
ＣＣＵ-１
ARC2
75Ω termination
Coaxial cable
CP cable
75Ω termination
OCP-200
MCP-200
Note:
- The OCP/CCP connector and CSU/CCP connector on the CCU/BS cannot be used with the ARCNET connector at the same time in
this configuration.
- This product cannot be connected to the BSH-200 (BS HUB).
■ ARCNET Connection (Expansion bus connection)
This connection configuration is available only for network-enabled CCU/BS such as the CCU-980 / BS-98.
Coaxial cable
ARC
CCU-3
BS-1
BS-2
BS-3
ARC
CP cable
OP8
OP7
OP6
OP5
ARC2
CPH-200
OP4
OP3
ARC1
OP2
OP1
OP8
OP7
OP6
CPH-200
OP5
OP4
OP3
ARC
ARC2
ARC1
Coaxial cable
OP1
CCU-2
75Ω termination
Coaxial cable
OP2
ＣＣＵ-1
CP cable
ARC
75Ω termination
ARC
ARC
OCP-200
OCP-200
Note:
- The OCP/CCP connector and CSU/CCP connector on the CCU/BS cannot be used with the ARCNET connector at the same time in
this configuration.
- This product cannot be connected to the BSH-200 (BS HUB).
44
BS-98 1409 VER1 (U) (E)
4.6
External Connections
4.6 External Connections
■ CAMERA Connector
Used to connect the camera head to its CCU/BS.
Two types of CAMERA connector are available.
[3K Series]
[OPS Series]
―― Receptacle ――
Guide mark
Pin No.
―― Receptacle ――
Guide mark
Insertion Side
Insertion Side
BS side : FFXW.3K or FCFRA
BS side : OPS-PR
Name
Function
I/O
1
○
OPT H - C/B
Light contact Camera --> CCU/BS
IN
2
○
OPT C/B - H
Light contact CCU/BS --> Camera
OUT
3
○
CONTROL (H)
Control signal (H) CCU/BS --> Camera
OUT
4
○
CONTROL (C)
Control signal (C) Camera --> CCU/BS
IN
5
○
POWER (H)
Power (H) supplied to the camera
OUT
6
○
POWER (C)
Power (C) supplied to the camera
OUT
BS-98 1409 VER1 (U) (E)
External Interface
45
4.6
External Connections
■ MIC-1 OUT Connector and MIC-2 OUT Connector
This is an output connector for the analog audio signal that is input from the camera head.
― Male receptacle ―
― Female receptacle ―
Insertion Side
Insertion Side
BS side
: HA16RM-3PE (76)
Cable side : XLR-3-11C (3-pin female plug) or equivalent
Pin No.
46
Name
BS side
: HA16PRM-3SE (71)
Cable side : XLR-3-12C (3-pin male plug) or equivalent
Function
I/O
1
○
SHIELD
AUDIO LINE SHIELD
GND
2
○
MIC (H)
AUDIO LINE HOT
OUT
3
○
MIC (C)
AUDIO LINE COLD
OUT
BS-98 1409 VER1 (U) (E)
External Interface
4.6
External Connections
■ COMMUNICATION Connector
This is the connector that connects the control inputs from the external INTERCOM system, program voice, and external TALLY
system.
The hex jack screw for the Japanese domestic models is 2.6 mm, and the hex jack screw for oversea models are #4-40UNC as the
standard specifications.
―― Receptacle ――
BS side
: 【metric】 17LE-13250-27(D3AB)-FA
【inch】 17LE-13250-27(D3AC)-FA
Cable side : DB-25PF-N or equivalent
Insertion Side
Pin No.
Name
Function
I/O
1
○
ENG B-S(H)
ENG CH Intercom output to the system from the CCU/BS (H)
OUT
2
○
ENG B-S(C)
ENG CH Intercom output to the system from the CCU/BS (C)
OUT
3
○
ENG(S)
ENG CH Intercom Shield
4
○
ENG S-B(H)
ENG CH Intercom input to the CCU/BS from the system (H)
IN
5
○
ENG S-B(C)
ENG CH Intercom input to the CCU/BS from the system (C)
IN
6
○
PGM-1(H)
Program Audio Channel-1 input (H)
IN
7
○
PGM-1(C)
Program Audio Channel-1 input (C)
IN
8
○
PGM-1(S)
Program Audio Channel-1 Shield
9
○
GND
Ground
10
○
Y TALLY IN
Yellow Tally Input (+)
IN
11
○
R TALLY IN
Red Tally Input (+)
IN
12
○
R TALLY COMM Red Tally Common
13
○
GND
Ground
GND
14
○
PROD B-S(H)
PROD CH Intercom output to the system from the CCU/BS (H)
OUT
15
○
PROD B-S(C)
PROD CH Intercom output to the system from the CCU/BS (C)
OUT
16
○
PROD(S)
PROD CH Intercom Shield
17
○
PROD S-B(H)
PROD CH Intercom input to the CCU/BS from the system (H)
IN
18
○
PROD S-B(C)
PROD CH Intercom input to the CCU/BS from the system (C)
IN
19
○
PGM-2(H)
Program Audio Channel-2 input (H)
IN
20
○
PGM-2(C)
Program Audio Channel-2 input (C)
IN
21
○
PGM-2(S)
Program Audio Channel-2 Shield
22
○
PGM-3(H)
Program Audio Channel-3 input (H)
IN
23
○
PGM-3(C)
Program Audio Channel-3 input (C)
IN
24
○
G TALLY IN
Green Tally Input (+)
IN
25
○
G TALLY COMM Green Tally Common
External Interface
GND
BS-98 1409 VER1 (U) (E)
47
4.6
External Connections
■ TALLY OUT Connector
Used to send TALLY control signal.
―― Receptacle ――
Insertion Side
Pin No.
Name
BS side
: PRC05-RB5F1
Cable side : PRC 05-P5M or equivalent
Function
I/O
A
○
DC +12 V OUT
DC +12V power output
OUT
B
○
R TALLY
Red Tally output (ON: GND)
OUT
C
○
Y TALLY/COM TALLY
Yellow Tally output or COMMON TALLY
output (ON: GND)
OUT
D
○
G TALLY
Green TALLY output (ON: GND)
OUT
E
○
TALLY GND
Ground for TALLY signal
GND
External Interface
- Select one from Y TALLY output or COMMON TALLY output for the pin C. It can be set from the CCU / BS menu.
Use of COMMON TALLY OUT enables to control both R TALLY and G TALLY simultaneously.
48
BS-98 1409 VER1 (U) (E)
4.6
External Connections
■ REMOTE Connector
This is a connector used to externally control the microphone gain of the camera head.
The hex jack screw for the Japanese domestic models is 2.6 mm, and the hex jack screw for oversea models are #4-40UNC as the
standard specifications.
[It is required that the camera head is compatible with the MIC GAIN REMOTE function.]
―― Receptacle ――
BS side
： 【metric】 17LE-13150-27(D3AB)-FA
【inch】 17LE-13150-27(D3AC)-FA
Cable side ： DA-15PF-N or equivalent
Insertion Side
Pin No.
Name
Function
I/O
1
○
+5.5V
DC + 5.5V output
2
○
MIC1̲FINE̲CTL
MIC1 GAIN control voltage input 0 to 5.5V
IN
3
○
MIC2̲FINE̲CTL
MIC2 GAIN control voltage input 0 to 5.5V
IN
4
○
NC
5
○
MIC1 GAIN STEP2
MIC1 GAIN STEP2
※1
IN
6
○
MIC1 GAIN STEP1
MIC1 GAIN STEP1
※1
IN
7
○
MIC1 GAIN STEP0
MIC1 GAIN STEP0
※1
IN
8
○
MIC1̲REM̲CTRL
MIC1 GAIN CONTROL ENABLE
9
○
GND
GND
10
○
NC
11
○
NC
12
○
MIC2 GAIN STEP2
MIC2 GAIN STEP2
※1
IN
13
○
MIC2 GAIN STEP1
MIC2 GAIN STEP1
※1
IN
14
○
MIC2 GAIN STEP0
MIC2 GAIN STEP0
※1
IN
15
○
MIC2̲REM̲CTRL
MIC2 GAIN CONTROL ENABLE
External Interface
OUT
※2
IN
※1 MIC GAIN STEP CONTROL
※2
IN
※2 MIC GAIN EXTERNAL REMOTE CONTROL
GAIN
STEP2
GAIN
STEP1
GAIN
STEP0
GAIN
MIC1
REM̲CTRL
MIC2
REM̲CTRL
H
H
H
-60 dB
L
L
MIC 1 and 2 ON
H
H
L
-50 dB
L
H
MIC 1 ON
H
L
H
-40 dB
H
L
MIC 2 ON
H
L
L
-30 dB
H
H
INTERNAL
L
H
H
-20 dB
L
H
L
-10 dB
L
L
H
0 dB
L
L
L
+4 dB
BS-98 1409 VER1 (U) (E)
MIC GAIN CTRL
49
4.6
External Connections
■ DATA TRK (DATA TRUNK)
This is the input/output connector for the serial communication standard RS-422.
―― Receptacle ――
BS side
: DE-9SF-T-N
Cable side : D-sub connector (9-pin male plug and inch screws #4-40UNC)
Insertion Side
Pin No.
50
Name
Function
I/O
1
○
N. C
2
○
TR1 OUT (−)
Digital Data Output (-)
OUT
3
○
TR1 IN (＋)
Digital Data Input (+)
IN
4
○
IN (S)
Input Shield
5
○
N. C
6
○
OUT (S)
Output Shield
7
○
TR1 OUT (＋)
Digital Data Output (+)
8
○
TR1 IN (−)
Digital Data Input (-)
9
○
GND
GND
OUT
IN
GND
BS-98 1409 VER1 (U) (E)
External Interface
4.6
External Connections
■ OCP/CCP and CSU/CCP Connector (MPU & REF module)
Used to connect Various control panel.
―― Receptacle ――
Insertion Side
Pin No.
Name
BS side
: RPC05-RB8F1
Cable side : PRC05-PB8M or equivalent
Function
I/O
A
○
HED (＋)
Digital data output (+) from CCU/BS to
control panel
OUT
B
○
HED (−)
Digital data output (-) from CCU/BS to
control panel
OUT
C
○
HEC (＋)
Digital data input (+) from control panel to
CCU/BS
IN
D
○
HEC (−)
Digital data input (-) from control panel to
CCU/BS
IN
E
○
＋12 V
DC +12V power output for control panel
OUT
F
○
＋12 V RET
DC +12V power RET (GND)
GND
G
○
INC C-CP
Audio output to the control panel from the CCU
OUT
(Only CP INCOM CCU)
H
○
INC CP-C
Audio input to the CCU from the control panel
(Only CP INCOM CCU)
BS-98 1409 VER1 (U) (E)
External Interface
IN
51
4.6
External Connections
■ IF Connector
The serial communication standard RS-422 DATA TRUNK #2, Intercom external control, and preview switch contact are
assigned.
In DATA TRUNK #2, it is necessary for the camera head side to support.
―― Receptacle ――
BS side
: HR10A-10R-12SC (71)
Cable side : HR10A-10P-12PC (73)
: HR10A-10P-12P (73)
Insertion Side
Pin No.
52
Name
Function
I/O
1
TR2 IN(+)
DTAT TRUNK2 Digital Data Input (+)
IN
2
TR2 IN(-)
DTAT TRUNK2 Digital Data Input (-)
IN
3
TR2 OUT(+)
DTAT TRUNK2 Digital Data Output (+)
OUT
4
TR2 OUT(-)
DTAT TRUNK2 Digital Data Output (-)
OUT
5
TR2(S)
DTAT TRUNK2 Shield
6
REM ISOLATE OFF
Private Incom OFF external control
IN
7
EXT MIC OFF
Camera Incom MIC OFF external control
IN
8
HP IND
Head Power ON IND output
OUT
9
+12V OUT
DC +12V power output
OUT
10
GND
Ground
GND
11
PREVIEW SW
Preview switch
OUT
12
PREVIEW COM
Preview switch GND
GND
BS-98 1409 VER1 (U) (E)
Crimp Type
Solder type
External Interface
BS SETTINGS and
ADJUSTMENT
5
54
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
5.1 Settings from the BS Menu
The menu operation on setting the CCU/BS is performed from the controlpanel or CCU/BS by itself.
The setting of each item is performed by displaying the main menu/submenu screen on the PM screen. CCU/BS menu is displayed
only PM OUT output.
Note:
Abbreviations
PM
: Abbreviation of Picture Monitor
PM screen : Means the PM OUT output screen of CCU/BS. On the PM screen, various characters are superimposed.
Basic Operation of the Menu (Operation from the MCP)
Special Function part
EFFECT
BARS button
MAN SET
DIAGNOS
SCREEN
16 : 9
FILE
CLR
SNAP
SHOT
SCENE
M. CARD
ENABLE
REF
SAVE
LOAD
JOB
START
SPECIAL button
CALL button
MASTER PEDESTAL
control knob
IRIS control knob
SPECIAL button/BARS button
: Pressing the SPECIAL button then pressing the BARS button will switch to the
CALL button
MASTER PEDESTAL control knob/IRIS
control knob
: Pressed to confirm the selection and setting.
menu mode and display the menu.
: Used to select a setting item.
■ Displaying the Main Menu
This section explains how to display the main menu on the PM screen.
1
Press the SPECIAL button on the MCP.
2
＊＊＊ ＭＥＮＵ ＊＊＊
▲
ＢＡＲＳ ＴＩＴＬＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＨＥＡＤ ＭＥＮＵ
ＩＮＦＯＲＭＡＴＩＯＮ
▼
Press the BARS button.
The main menu appears on the PM screen.
Note:
The flashing item on the main menu indicates the currently focused item. This flashing status is called the "flashing cursor" hereafter
(displayed in gray in the screen example).
BS-98 1409 VER1 (U) (E)
55
5.1
Settings from the BS Menu
■ Displaying the Submenu
You can perform various settings on the submenu that is displayed from the main menu on the PM screen.
1
Make sure that the main menu is displayed on the PM
screen.
2
Turn the MASTER PEDESTAL control knob or IRIS
control knob on the MCP to position the flashing cursor
on the setting item, and press the CALL button.
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＦＩＬＥ ＳＥＬＥＣＴ
ＬＯＡＤ ＳＴＡＲＴ
Setting items
ＥＮＧＩＮＥＥＲ−１
ＳＴＡＲＴ
Mode setting
The submenu appears, on which you can perform various
settings.
CAUTION:
Depending on the functions of the setting items, some items change the setting when the knob is turned; others change the setting
when the CALL button is pressed.
Note:
- To return to the main menu, select " " and press the CALL button.
- The flashing item on the submenu indicates the currently focused item. This flashing status is called the "flashing cursor" hereafter
(displayed in gray in the display example).
- Each time the CALL button is pressed, the flashing cursor switches to setting item -> mode selection -> setting item -> mode
selection and so on.
■ Exiting the Menu
This section explains how to exit the main menu/submenu on the PM screen.
1
Exit the menu screen in the any of the following methods :
a) Select " " on the BS/CCU main menu and press the CALL button.
b) Press the BARS button (to OFF COLOR BARS).
The main menu/submenu disappears.
56
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
Basic Operation of the Menu (Operation from the OCP-200)
■ Displaying the Main Menu
OCP-200
This section explains how to display the main menu on the PM
screen.
SETUP button
I
O
S
M
U
W
CHARACTER
File
Camera ID Scene
Name
Menu
Menu
Quit button
Quit
Enter
Select
Next
Enter button
Select knob
1
Press the SETUP button among the FUNCTION buttons
on the OCP-200.
The screen shown in Fig.1 is displayed on the liquid crystal
display (LCD) of the OCP.
Next knob
Figure 1
CAMERA SETUP
GRAY
SCALE
DETAIL
COLOR
AUTO
SETUP
DOWN CONV.
DETAIL
DOWN CONV.
COLOR
CHARACTER
MODE
SWITCH
CHARACTER button
2
Press the CHARACTER button on the LCD.
Figure 2
CHARACTER
The screen shown in Fig.2 is displayed.
Menu
Camera ID
Scene File
Name
Menu button
3
Press the Menu button on the LCD for a while.
The menu screen (Fig.3) appears on the LCD, and the main
menu screen appears on the PM.
Figure 3 (menu display)
CHARACTER
Menu
Camera ID
Scene File
Name
Menu
Quit
Enter
Select
BS-98 1409 VER1 (U) (E)
Next
57
5.1
Settings from the BS Menu
■ Displaying the Submenu
You can perform various settings on the submenu that is displayed from the main menu on the PM screen.
1
2
Make sure that the main menu screen is displayed on the PM screen.
Turn the Select knob or Next knob to position the flashing cursor on the setting item, and press the Enter button
on the LCD.
The submenu appears, on which you can perform various settings.
CAUTION:
Depending on the functions of the setting items, some items change the setting when the knob is turned; others change the setting
when the Enter button on the LCD is pressed.
■ Exiting the Menu
This section explains how to exit the main menu/submenu on the PM screen.
1
Exit the menu screen in the any of the following methods :
a) Select " " on the BS/CCU main menu and press the Enter button.
b) Press the QUIT button on the LCD.
c) Press the BARS button on the OCP (to OFF COLOR BARS).
58
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
Basic operation of the menu screen (when operated from the CCU/BS main body)
■ Display of the main menu screen
It explains the method to display the main menu on the PM screen.
CCU operation panel
1
[In case of CCU]
Set the MENU switch "OPE - OFF" to "OPE" side.
[In case of BS]
Set the MENU switch "OPE - LOCK" to "OPE" side.
BS operation panel
2
When the MENU operation dial is kept pressed for approximately three seconds, the Main menu screen is
displayed on the PM screen.
■ Display of the sub-menu screen
Select the item from the main menu screen that is displayed on the PM screen to display the sub menu screen for various settings.
1
2
Check that the main menu screen is displayed on the PM screen.
Turn the MENU operation dial to set the blinking cursor to the
setting item and press the dial. The sub menu is displayed,
and various settings become enabled. It provides the operation
method that is to select an item by turning and pressing the
dial.
Caution:
Depending on the function of the setting item, there are items that the setting is changed when the dial is turned or when the dial is
pressed.
■ Exit the menu screen
End the Main menu screen and Sub menu screen displayed on the PM screen.
1
Exit the menu screen in the any of the following methods :
a) Select " " on the BS/CCU main menu and press the Enter button.
b) Set the MENU switch "OPE - OFF" to the "OFF" side (CCU).
c) Set the MENU switch "OPE - LOCK" to the "LOCK" side (BS).
BS-98 1409 VER1 (U) (E)
59
5.1
Settings from the BS Menu
Menu Configuration
The following lists the CCU/BS menu configuration.
■ MENU
BARS TITLE
Return to a main menu screen.
DISPLAY
ON/OFF setting of BARS TITLE character display
TITLE EDIT
Editing BARS TITLE character
POSITION
Setting of the BARS TITLE character indication point
PRESET FILE LOAD
Return to a main menu screen.
FILE SELECT
Selection of the file to LOAD
LOAD START
Execution of the DATA LOAD
HEAD MENU
Control the menu of the camera head
INFORMATION
Return to a main menu screen.
MODULE SW
Display of the switch settings of the PLS and MPU&REF module
ROM VER
Display a version of Firmware
CHECK SUM
Display CHECK SUM of Firmware
USER ID
Indication of the regional and customer specifications information
■ ENGINEER (1/2)
SYSTEM FORMAT
Return to a main menu screen.
FRAME RATE
Selection of FRAME RATE
1080xxx
Selection of SYSTEM FORMAT
OUTPUT FORMAT
Return to a main menu screen.
60
OUT-1
Format selection of HDTV output 1 (2 outputs)
OUT-2
Format selection of HDTV output 2 (2 outputs)
OUT-3
Format selection of HDTV/SDTV output 3 (2 outputs)
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
PM OUT-1
Format selection of PM output 1
PM-2/WFM
Format selection of PM output 2 or WFM output
HD PM
Select the format of the output 3G/HD-SDI PM
SD SCREEN MODE
Select a screen mode of the SDTV output
SYNC OUT
Select the format of the SYNC OUT output
HD-SYNC 2-3ID ADD
ON/OFF
Selection of whether to add 2-3 ID signal to the SYNC output
SD-10 FIELD ID SIG
ON/OFF
Selection of whether to add 10 FIELD ID signal to the ENC output
RET VIDEO FORMAT
Return to a main menu screen.
RET 1 ******* IN
FS ON/OFF
Selection of FS ON/OFF and Display of RETURN-1 detection signal format
RET 2 ******* IN/OUT
FS ON/OFF
Selection of FS ON/OFF and Display of RETURN-2 detection signal format
RET 3 ******* IN
FS ON/OFF
Selection of FS ON/OFF and Display of RETURN-3 detection signal format
RET 4 ******* IN/OUT
FS ON/OFF
Selection of FS ON/OFF and Display of RETURN-4 detection signal format
ACTIVE-THROUGH
ON/OFF
ON/OFF selection of RETURN active through mode
SD SCREEN MODE
Select a screen mode of the SDTV signal input
PHASE CONTROL
Return to a main menu screen.
SYNC CONT
Set the vertical phase of SDTV and HDTV for external synchronization
HD V PHASE
Set the vertical phase of HDTV output signal for external synchronization
(Format name)
HD TRUNK
SYS1/SYS2
The simultaneous output, it is possible to individually adjust the system of SYS2 with SYS1
Adjust the vertical phase of HD TRUNK signal
HD MASTER H PHASE
Adjust the horizontal master phase of HDTV output signal for external synchronization
HD OUT-1 H PHASE
Adjust the horizontal phase of OUT-1 output signal for external synchronization
HD OUT-2 H PHASE
Adjust the horizontal phase of OUT-2 output signal for external synchronization
HD OUT-3 H PHASE
Adjust the horizontal phase of OUT-3 HDTV output signal for external synchronization
HD PM H PHASE
Adjust the horizontal phase of PM OUT output signal for external synchronization
HD TRUNK H PHASE
Adjust the horizontal phase of HD TRUNK output signal for external synchronization
SD V PHASE
Adjust the vertical phase phase of SDTV output signal for external synchronization
SD MASTER H PHASE
Adjust the horizontal master phase of SDTV output signal for external synchronization
SD OUT-3 H PHASE
Adjust the horizontal phase of OUT-3 SDTV output signal for external synchronization
SD SC PHASE COARSE
Coarse adjustment of the phase of the SDTV subcarrier
SD SC PHASE FINE
Fine adjustment of the phase of the SDTV subcarrier
SD ENC H PHASE
Adjust the horizontal phase of SDTV ENC output signal for external synchronization
SD PM H PHASE
Adjust the horizontal phase of SDTV PM output signal for external synchronization
SYNC OUT H PHASE
Adjust the horizontal phase of the external synchronization output (SYNC OUT)
SYNC OUT V PHASE
Adjust the vertical phase of the external synchronization output (SYNC OUT)
BS-98 1409 VER1 (U) (E)
61
5.1
Settings from the BS Menu
MIC MANAGEMENT
Return to a main menu screen.
HD SYS EMBEDDED
ALL ON/OFF
Set whether to embed audio signal to all HDTV output.
HD OUT-1
ON/OFF
Set whether to embed audio signal to HDTV OUT-1 output.
HD OUT-2
ON/OFF
SSet whether to embed audio signal to HDTV OUT-2 output.
HD OUT-3
ON/OFF
Set whether to embed audio signal to HDTV OUT-3 output.
HD PM
ON/OFF
Set whether to embed audio signal to HDTV PM OUT output.
ALL ON/OFF
Set whether to embed audio signal to all SDTV output.
SD SDI
ON/OFF
Set whether to embed audio signal to SDTV OUT-3 output.
SD PM
ON/OFF
Set whether to embed audio signal to SDTV PM OUT output.
SD SYS EMBEDDED
MASTER DELAY
Sets the audio delay for all systems
HD SYS DELAY
Sets the audio delay for HDTV systems
SD SYS DELAY
Sets the audio delay for SDTV systems
DIGITAL DELAY
Sets the audio delay for digital audio output
MIC1/2 OUT DELAY
Sets the audio delay for analog audio output
MIC1 OUTPUT LEVEL
Set the output reference level of MIC1 OUT (0dB/4dB)
MIC1 LVL ADJ (0dB)
Set the level 0dB setting of MIC1 OUT
MIC1 LVL ADJ (4dB)
Set the level 4dB setting of MIC1 OUT
MIC2 OUTPUT LEVEL
Set the output reference level of MIC2 OUT (0dB/4dB)
MIC2 LVL ADJ (0dB)
Set the level 0dB setting of MIC2 OUT
MIC2 LVL ADJ (4dB)
Set the level 4dB setting of MIC2 OUT
MIC1 CENTER ADJ
Center OFFSET adjustment of MIC1 GAIN REMOTE external control voltage
MIC2 CENTER ADJ
Center OFFSET adjustment of MIC2 GAIN REMOTE external control voltage
INCOM MANAGEMENT
Return to a main menu screen.
62
ENG
IF
Selection of the for ENG-line system interface 4W/RTS/Cler-Com.
ENG-INPUT
TERM
Selection of the input termination 600/10K of the ENG-line system interface.
ENG-OUTPUT
LOAD
Termination setup for ENG-line RTS/Cler-Com system
PROD
IF
Selection of the PROD-line system interface 4W/RTS/Cler-Com.
PROD-INPUT
TERM
Selection of the input termination 600/10K of the PROD-line system interface.
PROD-OUTPUT
LOAD
Termination setup for PROD-line RTS/Cler-Com system
ENG-PROD 2LINE/1LINE
To choose whether to 1-line or 2-lines to the system line
FRONT INCOM
Select the type of headset microphone to be connected to the front of the connector.
MIC POWER SUPPLY
Set whether or not to microphone power the ECM setting
PGM1 TERM
Select the line termination 600/10K of PGM1
PGM1 INPUT LEVEL
Select the Input level -20dB/0dB/4dB of PGM1
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
PGM2 TERM
Select the line termination 600/10K of PGM2
PGM2 INPUT LEVEL
Select the Input level -20dB/0dB/4dB of PGM2
PGM3 TERM
Select the line termination 600/10K of PGM3
PGM3 INPUT LEVEL
Select the Input level -20dB/0dB/4dB of PGM3
PGM MIX FRONT INCOM
The selection as to whether or not to mix the PGM to FRONT INCOM
PGM -> FR-INCOM LEVEL
The adjustment of the PGM mix level in FRONT INCOM
■ ENGINEER (2/2)
HDTV VIDEO PROCESS
Return to a main menu screen.
GAMUT CLIP
LEVEL
HDTV BARS TYPE
Select ON/OFF of the GAMUT CLIP function
Set the level of GAMUT CLIP
Select the type of HDTV COLOR BARS
ARIB BARS TYPE
Select a pattern of ARIB BARS
SMPTE BARS TYPE1
Select a pattern of SMPTE BARS #1
SMPTE BARS TYPE2
Select a pattern of SMPTE BARS #2
CHAR LEVEL
HDTV output character level. Factory setting
CHAR BG LEVEL
HDTV output character background level. Factory setting
SDTV VIDEO PROCESS
Return to a main menu screen.
HV SLIM DTL TYPE
Set horizontal and vertical SLIM DTL type of the SDTV system.
V SLIM DTL FREQ
Set the frequency or boost band for SDTV system
FINE DTL
Setting of FINE DTL
COMB
COMB FILTER setting. Factory setting
COMB GAIN
COMB FILTER GAIN. Factory setting
H FILTER
Set of SDTV output horizontal filter
V FILTER
Set of SDTV output vertical filter
MOTION DETECT
Set the motion detection of Down Converter
GAMUT CLIP
Select ON/OFF of the GAMUT CLIP function
LEVEL
Set the level of GAMUT CLIP
SDTV SETUP SEL
Factory setting
SDTV BARS TYPE
Select the type of SDTV COLOR BARS
CHAR LEVEL
Set of SDTV output Character Level
CHAR BG LEVEL
Set of SDTV output character background level
BS-98 1409 VER1 (U) (E)
63
5.1
Settings from the BS Menu
HD PM VIDEO PROCESS
Return to a main menu screen.
CHAR LEVEL
Set of HDTV PM output Character Level
CHAR BG LEVEL
Set of HDTV PM output character background level
CAM HEAD STATUS DISP
ON/OFF setting of the camera head status display
DISP POSITION
Setting the display position of the character
SD PM VIDEO PROCESS
Return to a main menu screen.
CHAR LEVEL
Set of SDTV PM output Character Level
CHAR BG LEVEL
Set of SDTV PM output character background level
FUNCTION SETTING
Return to a main menu screen.
ARCNET ID SET
Setting of ARCNET ID (Decimal Number)
CAM PGM NO. ENABLE
Set CCU/BS of whether or not to manage the camera program number
CAM PGM NO. SET
Setting of the camera program number
BS FRONT ID DISPLAY
Selection of items to be displayed in the FRONT ID DISPLAY
PM TALLY SEL
Selection of COMM TALLY OUT or Y TALLY OUT
CAM CODE
Regional options
SAFETY&H.PWR
Regional options
REPEATER MODE
Regional options
CAM PWR CONT
Regional options
Q-TV MODE
Set of Composite QTV
HD TRUNK
ON / OFF function of HD TRUNK (Only 3G transmission compatible camera. It
works with 3G transmission mode.)
HD Q-TV
ON / OFF function of HD QTV (Only 3G transmission compatible camera)
WARNING BIG CHAR
Display to the DIAGNOSIS INFORMATION results by big character
FIBER SINGLE MODE
ON / OFF of the FIBER SINGLE MODE function
ENGINEER SET FILE RENEW
Return to a main menu screen.
FILE SELECT
Selection of files to be updated
DATA RENEW MODE
Update execution of the file data
PASSWORD ENTRY
64
I will put a password to protect ENGINEER SET FILE RENEW function.
(Valid for S3-3 ON of PLS module)
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
PROGRAM UPDATE
Return to a main menu screen.
CCU/BS ROM
Run the update of Firmware
Current Ver STR-****V**
Displaying the Firmware version of the current
BS-98 1409 VER1 (U) (E)
65
5.1
Settings from the BS Menu
BARS TITLE
Superimposing the character on COLOR BARS becomes enabled.
Reference:
Refer to the manual for each control panel for details on how to set the bars title data.
＊＊＊ ＭＥＮＵ ＊＊＊
▲
ＢＡＲＳ ＴＩＴＬＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＨＥＡＤ ＭＥＮＵ
ＩＮＦＯＲＭＡＴＩＯＮ
▼
To position the flashing cursor on the
"BARS TITLE", and determine.
ＢＡＲＳ ＴＩＴＬＥ ＥＮＴＲＹ
ＤＩＳＰＬＡＹ： ＯＦＦ
ＴＩＴＬＥ ＥＤＩＴ
ＰＯＳＩＴＩＯＮ
−−− ＯＰＥ．ＧＵＩＤＥ −−−
ＭＥＮＵ ＳＥＬ：（ＳＥＬ）ＫＮＯＢ
ＥＮＴＥＲ
：（ＥＮＴＥＲ）ＫＥＹ
DISPLAY
: ON / OFF selection of BARS TITLE character display
TITLE EDIT : BARS TITLE character editing mode
POSITION : Set of BARS TITLE character display position
The submenu "BARS TITLE ENTRY"
is displayed, on which you can perform
various settings.
66
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
PRESET FILE LOAD
PRESET FILE DATA transfers to the memory.
＊＊＊ ＭＥＮＵ ＊＊＊
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
▲
ＢＡＲＳ ＴＩＴＬＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＨＥＡＤ ＭＥＮＵ
ＩＮＦＯＲＭＡＴＩＯＮ
▼
ＦＩＬＥ ＳＥＬＥＣＴ ＥＮＧＩＮＥＥＲ−１
ＬＯＡＤ ＳＴＡＲＴ
ＳＴＡＲＴ
To position the flashing cursor on the
"PRESET FILE LOAD", and determine.
Setting Item
FILE SELECT
LOAD START
1
The submenu "PRESET FILE LOAD"
is displayed, on which you can perform
various settings.
Set Value
ENGINEER-1
Description
Sets the ENGINEER-1 file
ENGINEER-2
Sets the ENGINEER-2 file
ENGINEER-3
Sets the ENGINEER-3 file
FACTORY
Sets the FACTORY file
READY
Data transfer (LOAD) before execution.
START
Data transfer (LOAD) start.
CANCEL
Data transfer (LOAD) cancellation.
Set the blinking cursor to FILE SELECT and select a target file to transfer (LOAD) the data.
When the blinking cursor is moved to "LOAD START" and finalized, the mode set value changes from "READY" to
"START".
2
3
- When "CANCEL" is selected, the setting is canceled, and the status returns to "READY" status.
- When "START" is selected, "PUSH SET -> START" is displayed at the lower section of the screen. When
"START" is selected, proceed to Step 3.
While "PUSH SET -> START" is selected, finalize the operation. The data transfer (LOAD) starts.
When loading of the file completes, the message "FAIL-SAFE DATA LOAD COMPLETED" appears on the screen. Then,
BS/CCU re-start automatically, and the operation completes.
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＦＩＬＥ ＳＥＬＥＣＴ ＥＮＧＩＮＥＥＲ−１
ＬＯＡＤ ＳＴＡＲＴ
ＳＴＡＲＴ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＦＩＬＥ ＳＥＬＥＣＴ ＥＮＧＩＮＥＥＲ−１
ＬＯＡＤ ＳＴＡＲＴ
ＳＴＡＲＴ
ＰＵＳＨ ＳＥＴ→ＳＴＡＲＴ
Position the flashing cursor on "LOAD
START", and confirm the selection.
When "START" is selected, the message
is displayed in the bottom of the screen.
BS-98 1409 VER1 (U) (E)
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＦＩＬＥ ＳＥＬＥＣＴ ＥＮＧＩＮＥＥＲ−１
ＬＯＡＤ ＳＴＡＲＴ
ＳＴＡＲＴ
ＣＯＭＰＬＥＴＥＤ
"FAIL-SAFE DATA LOAD
COMPLETED" is displayed in the
middle of the screen, and then restart.
67
5.1
Settings from the BS Menu
HEAD MENU
The camera head menu is displayed, and its control is possible.
＊＊＊ ＭＥＮＵ ＊＊＊
▲
ＢＡＲＳ ＴＩＴＬＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＨＥＡＤ ＭＥＮＵ
ＩＮＦＯＲＭＡＴＩＯＮ
▼
Operating the camera head menu becomes enabled from CCU/BS.
For the contents of the camera menu, refer to the manual of each camera head.
＊＊＊ ＭＥＮＵ ＊＊＊
▲
ＢＡＲＳ ＴＩＴＬＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＨＥＡＤ ＭＥＮＵ（Ｂａｒｓ Ｏｎ ｔｏ Ｖｉｅｗ）
ＩＮＦＯＲＭＡＴＩＯＮ
▼
Note:
＊＊＊ ＭＥＮＵ ＊＊＊
▲
ＢＡＲＳ ＴＩＴＬＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＨＥＡＤ ＭＥＮＵ（Ｈｅａｄ Ｐｏｗｅｒ ＯＦＦ）
ＩＮＦＯＲＭＡＴＩＯＮ
▼
68
When operating HEAD MENU, it is required that COLOR BARS is ON. When
COLOR BARS is OFF, "HEAD MENU (Bars On to View)" is displayed, and the
selecting operation is disabled.
In addition, when the camera head is not connected or when HEAD POWER is
OFF, "HEAD MENU (Head Power OFF)" is displayed, and selecting operation is
disabled.
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
INFORMATION
INFORMATION displays the switch settings and ROM version.
＊＊＊ ＭＥＮＵ ＊＊＊
ＩＮＦＯＲＭＡＴＩＯＮ
▲
ＭＯＤＵＬＥ ＳＷ
ＲＯＭ ＶＥＲ
ＳＴＲ−ｘｘｘｘＶｘｘ．ｘｘ．ｘｘ
ＣＨＥＣＫ ＳＵＭ （ＸＸＸＸ）
ＢＡＲＳ ＴＩＴＬＥ
ＰＲＥＳＥＴ ＦＩＬＥ ＬＯＡＤ
ＨＥＡＤ ＭＥＮＵ
ＩＮＦＯＲＭＡＴＩＯＮ
▼
ＵＳＥＲ ＩＤ
ＳＴＡＮＤＡＲＤ
ＣＯＰＹＲＩＧＨＴ（Ｃ）２０１４
ＩＫＥＧＡＭＩ ＴＳＵＳＨＩＮＫＩ ＣＯ．，ＬＴＤ．
To position the flashing cursor on the
"INFORMATION", and determine.
Setting Item
The submenu "INFORMATION" is
displayed.
Set Value
Description
MODULE SW
Only display
Displays the switch settings of the PULSE module and MPU&REF module.
ROM VER
Only display
Displays ROM ROM (Firmware) version.
CHECK SUM
Only display
Displays the ROM (Firmware) check sum.
USER ID
Only display
I will display the customer's specification and information area.
BS-98 1409 VER1 (U) (E)
69
5.1
Settings from the BS Menu
SYSTEM FORMAT
SYSTEM FORMAT sets the system format.
＊＊＊ ＥＮＧＩＮＥＥＲ（１／２） ＊＊＊
▲
ＳＹＳＴＥＭ ＦＯＲＭＡＴ
ＯＵＴＰＵＴ ＦＯＲＭＡＴ
ＲＥＴ ＶＩＤＥＯ ＦＯＲＭＡＴ
ＰＨＡＳＥ ＣＯＮＴＲＯＬ
ＭＩＣ ＭＡＮＡＧＥＭＥＮＴ
ＩＮＣＯＭ ＭＡＮＡＧＥＭＥＮＴ
▼
To position the flashing cursor on the
"SYSTEM FORMAT", and determine.
ＳＹＳＴＥＭ ＦＯＲＭＡＴ
ＦＲＡＭＥ ＲＡＴＥ
５９．９４Ｈｚ
１０８０Ｉ５９
１０８０Ｐ２３ＰＤ
１０８０Ｐ２９ＳＦ
◎
○
○
１０８０Ｐ５９
１０８０Ｉ５９
１０８０Ｐ２３ＰＤ
１０８０Ｐ２９ＳＦ
○
○
○
○
Set the blinking cursor to the format to be
set and execute the setting as the mark on
the screen becomes " ◎ ".
The figure is one example when the frame
rate is 59.94 Hz. The select-able format is
the one that the camera head corresponds to.
Note:
The formats, which are displayed on MENU and are select-able, are the ones that the connected camera head is compatible with only.
70
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
OUTPUT FORMAT
Set the output format of each output.
＊＊＊ ＥＮＧＩＮＥＥＲ（１／２） ＊＊＊
▲
ＳＹＳＴＥＭ ＦＯＲＭＡＴ
ＯＵＴＰＵＴ ＦＯＲＭＡＴ
ＲＥＴ ＶＩＤＥＯ ＦＯＲＭＡＴ
ＰＨＡＳＥ ＣＯＮＴＲＯＬ
ＭＩＣ ＭＡＮＡＧＥＭＥＮＴ
ＩＮＣＯＭ ＭＡＮＡＧＥＭＥＮＴ
▼
ＯＵＴＰＵＴ ＦＯＲＭＡＴ
ＯＵＴ−１
ＯＵＴ−２
ＯＵＴ−３
ＰＭ−１
ＰＭ−２／ＷＦＭ
ＨＤ ＰＭ
１０８０Ｐ５９ ＹＣ ３Ｇ
１０８０Ｐ５９ ＹＣ ３Ｇ
１０８０Ｉ５９ ＹＣ ＨＤ
ＰＭ ＨＤ−ＳＤＩ
ＷＦＭ （ＯＵＴ−３）
１０８０Ｉ５９ ＹＣ ＨＤ
ＳＤ ＳＣＲＥＥＮ ＭＯＤＥ
ＯＵＴ−１
１０８０Ｐ５９ ＹＣ ４２２ ３Ｇ−ＳＤＩ
◎
１０８０Ｐ５９ ＹＣ ４２２ ＤＵＡＬ−ＬＩＮＫ ○
１０８０Ｉ５９ ＹＣ ４２２ ＨＤ−ＳＤＩ
○
４：３
ＳＹＮＣ ＯＵＴ
１０８０Ｉ５９
ＨＤ−ＳＹＮＣ ２−３ＩＤ ＡＤＤ −−−
ＳＤ−１０ＦＩＥＬＤ ＩＤ ＳＩＧ −−−
Set the blinking cursor to "OUTPUT
FORMAT" and finalize.
The sub menu "OUTPUT FORMAT" is
displayed.
ＯＵＴ−１
Note:
For converter output
When 1080P23PD is selected in SYSTEM
FORMAT, the select-able FORMAT
of each output are three types that are
1080P23PD, 1080P23SF, and 1080P23.
Within these, 1080P23SF and 1080P23
use the converter; therefore, only one of
these can be selected.
Simultaneous output of 1080P23SF and
1080P23 is not possible.
1080P23PD and 1080P23SF or
1080P23PD and 1080P23 are the
simultaneous output.
ＦＲＡＭＥ ＲＡＴＥ
５９．９４Ｈｚ
１０８０Ｉ５９
１０８０Ｐ２３ＰＤ
１０８０Ｐ２９ＳＦ
○
◎
○
１０８０Ｐ５９
１０８０Ｉ５９
１０８０Ｐ２３ＰＤ
１０８０Ｐ２９ＳＦ
○
○
○
○
When SYSTEM FORMAT selects
1080P23PD format.
OUT-1 selects 1080P23SF.
１０８０Ｐ２３ＰＤ ＹＣ ４２２ ＨＤ−ＳＤＩ ○
１０８０Ｐ２３ＳＦ ＹＣ ４２２ ＨＤ−ＳＤＩ ◎
１０８０Ｐ２３
ＹＣ ４２２ ＨＤ−ＳＤ ○
ＯＵＴ−２
ＳＹＳＴＥＭ ＦＯＲＭＡＴ
When "OUT-1", "OUT-2", "OUT-3", and
"HD PM" are selected, sub menus open,
and the format select screen opens.
The figure is OUT-1 select screen when
the SYSTEM FORMAT is 1080P59 3G
as one example.
Items that can be selected vary
depending on each format and output
system.
１０８０Ｐ２３ＰＤ ＹＣ ４２２ ＨＤ−ＳＤＩ ◎
１０８０Ｐ２３ＳＦ ＹＣ ４２２ ＨＤ−ＳＤＩ ○
１０８０Ｐ２３
ＹＣ ４２２ ＨＤ−ＳＤＩ ×
ＯＵＴ−３
１０８０Ｐ２３ＰＤ ＹＣ ４２２ ＨＤ−ＳＤＩ ○
１０８０Ｐ２３ＳＦ ＹＣ ４２２ ＨＤ−ＳＤＩ ◎
１０８０Ｐ２３
ＹＣ ４２２ ＨＤ−ＳＤＩ ×
５２５Ｉ５９
ＳＤ−ＳＤＩ ○
BS-98 1409 VER1 (U) (E)
OUT-2 selection screen
The converter is used at
1080P23SF; therefore, the
selection for OUT-2 becomes
either one of 1080P23PD or
1080P23SF.
Selecting 1080P23 is disabled.
Selection for OUT-3 also becomes
either one of 1080P23PD or
1080P23SF.
(When SDTV option is
implemented, SD-SDI is selectable.)
71
5.1
Settings from the BS Menu
OUTPUT FORMAT setting item list
Setting items
Setting
Content
OUT-1
Changes depending on the
FORMAT.
Selects OUT-1 output from the sub menu.
OUT-2
Changes depending on the
FORMAT.
Selects OUT-2 output from the sub menu.
OUT-3
Changes depending on the
FORMAT.
Selects OUT-3 output from the sub menu.
When SDTV option is implemented, SD-SDI also becomes selectable.
PM-1
PM-2/WFM
HD PM
SD SCREEN MODE
PM HD-SDI
PM-1 OUT output is set to HD-SDI. The output format is selected by "HD PM"
item.
PM SD-SDI
PM-1 OUT output is set to SD-SDI. Only when SDTV option is implemented,
selection is enabled.
WFM (OUT-3)
PM HD-SDI
PM-2 OUT output is set to HD-SDI. The output format is the same as PM-1.
PM SD-SDI
PM-2 OUT output is set to SD-SDI. Only when SDTV option is implemented,
selection is enabled.
Changes depending on the
FORMAT.
The output format for when PM HD-SDI is selected to PM-1 and PM-2 OUT is
selected.
4:3
The aspect ratio of SDTV output is set to 4:3.
16:9
The aspect ratio of SDTV output is set to 16:9.
LETTER
SYNC OUT
HD-SYNC 2-3ID ADD
(Can be set only when
1080P23PD)
SD-10 FIELD ID SIG
(Can be set only when
1080P23PD)
SDTV output is set to the letter box mode.
Changes depending on the
FORMAT.
For the HDTV system, Tri-Level synchronizing signal, of which output is possible
with the SYSTEM FORMAT currently selected, can be selected.
SDTV is the 2Vp-p SDTV rate synchronizing signal (not BBS).
ON
Set as the pulse signals that counted the first to fifth frames superimpose in the
SYNC output.
OFF
Above signals are not superimposed.
---
Is not selectable.
ON
Set as the pulse signals (Level 40IRE) that counted the first to fifth frames to 15H
and 278H superimpose in the ENC output.
OFF
Above signals are not superimposed.
---
72
The signal that is the same as the one selected at OUT-3 is output.
Is not selectable.
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
RET VIDEO FORMAT
RET VIDEO FORMAT sets the return video signals.
＊＊＊ ＥＮＧＩＮＥＥＲ（１／２） ＊＊＊
ＲＥＴ ＶＩＤＥＯ ＦＯＲＭＡＴ
▲
ＳＹＳＴＥＭ ＦＯＲＭＡＴ
ＯＵＴＰＵＴ ＦＯＲＭＡＴ
ＲＥＴ ＶＩＤＥＯ ＦＯＲＭＡＴ
ＰＨＡＳＥ ＣＯＮＴＲＯＬ
ＭＩＣ ＭＡＮＡＧＥＭＥＮＴ
ＩＮＣＯＭ ＭＡＮＡＧＥＭＥＮＴ
▼
ＲＥＴ１
ＲＥＴ２
ＲＥＴ３
ＲＥＴ４
To position the flashing cursor on the "RET
VIDEO FORMAT", and determine.
１０８０Ｉ５９
ＩＮ
５２５Ｉ５９
ＩＮ
ＮＯＮ ＤＥＴＥＣＴ
ＮＯＮ ＤＥＴＥＣＴ
ＦＳ
ＦＳ
ＦＳ
ＦＳ
ＯＦＦ
ＯＮ
ＯＦＦ
ＯＦＦ
ＡＣＴＩＶＥ−ＴＨＲＯＵＧＨ
ＯＦＦ
ＳＤ ＳＣＲＥＥＮ ＭＯＤＥ
４：３
The submenu "RET VIDEO FORMAT"
is displayed, on which you can perform
various settings.
ＲＥＴ ＶＩＤＥＯ ＦＯＲＭＡＴ
ＲＥＴ１
ＲＥＴ２
ＲＥＴ３
ＲＥＴ４
１０８０Ｉ５９
１０８０Ｉ５９
５２５Ｉ５９
５２５Ｉ５９
ＩＮ
ＯＵＴ
ＩＮ
ＯＵＴ
ＦＳ ＯＦＦ
----ＦＳ ＯＦＦ
-----
ＡＣＴＩＶＥ−ＴＨＲＯＵＧＨ
ＯＮ
ＳＤ ＳＣＲＥＥＮ ＭＯＤＥ
４：３
When the "ACTIVE-THROUGH" ON
Setting Item
RET-1
RET-2
RET-3
RET-4
ACTIVE-THROUGH
SD SCREEN MODE
Set Value
Input signal display
FS ON/OFF
Description
Signals that are input to RETURN-1 are automatically recognized and the format
is displayed. When an asynchronous signal or a signal with a different frame rate
is input, FS (Frame Synchronizer) automatically turns on.
Input and output signal Signals that are input to RETURN-2 are automatically recognized and the format
display
is displayed. When an asynchronous signal or a signal with a different frame rate
FS ON/OFF
is input, FS (Frame Synchronizer) automatically turns on.
Input signal display
FS ON/OFF
Signals that are input to RETURN-3 are automatically recognized and the format
is displayed. When an asynchronous signal or a signal with a different frame rate
is input, FS (Frame Synchronizer) automatically turns on.
Input and output signal Signals that are input to RETURN-4 are automatically recognized and the format
display
is displayed. When an asynchronous signal or a signal with a different frame rate
FS ON/OFF
is input, FS (Frame Synchronizer) automatically turns on.
OFF
RET_IN channels 1 to 4 on the rear side function as input ports.
ON
RET_IN channels 1 and 3 on the rear side function as input ports, and channels 2
and 4 function as output ports.
4:3
The aspect ratio of SDTV input signal is set to 4:3.
16:9
The aspect ratio of SDTV input signal is set to 16:9.
LETTER
SDTV input signal is set to the letter box mode.
・Three rate signals of 3G-SDI/HD-SDI/SD-SDI are automatically recognized.
・When the ACTIVE-THROUGH function is used, both CCU and the camera head have the two return channel specification.
When the CCU/BS power is not on, through output is not executed.
・SDTV input signal is conformable to the SDI signal only and not VBS.
・When the input signal format switches to a signal that does not require FS while the FS (Frame Synchronizer) is on, the FS does
not turn off automatically. If FS is not necessary, turn off FS manually.
BS-98 1409 VER1 (U) (E)
73
5.1
Settings from the BS Menu
PHASE CONTROL
PHASE CONTROL sets the various video phase.
ＰＨＡＳＥ ＣＯＮＴＲＯＬ
＊＊＊ ＥＮＧＩＮＥＥＲ（１／２） ＊＊＊
▲
ＳＹＳＴＥＭ ＦＯＲＭＡＴ
ＯＵＴＰＵＴ ＦＯＲＭＡＴ
ＲＥＴ ＶＩＤＥＯ ＦＯＲＭＡＴ
ＰＨＡＳＥ ＣＯＮＴＲＯＬ
ＭＩＣ ＭＡＮＡＧＥＭＥＮＴ
ＩＮＣＯＭ ＭＡＮＡＧＥＭＥＮＴ
▼
To position the flashing cursor on the
"PHASE CONTROL", and determine.
ＳＹＮＣ ＣＯＮＴ
ＨＤ Ｖ ＰＨＡＳＥ
１０８０Ｐ２３ＰＤ
ＳＹＳ１
１０８０Ｐ２３ＳＦ
ＳＹＳ２
ＨＤ ＴＲＵＮＫ
ＨＤ ＭＡＳＴＥＲ Ｈ ＰＨＡＳＥ
ＨＤ ＯＵＴ−１ Ｈ ＰＨＡＳＥ
ＨＤ ＯＵＴ−２ Ｈ ＰＨＡＳＥ
ＨＤ ＯＵＴ−３ Ｈ ＰＨＡＳＥ
ＨＤ ＰＭ Ｈ ＰＨＡＳＥ
ＯＦＦ
０
２２５
０
０
０
０
０
０
The submenu "PHASE CONTROL" is
displayed, on which you can perform
various settings.
ＰＨＡＳＥ ＣＯＮＴＲＯＬ
ＨＤ ＴＲＵＮＫ Ｈ ＰＨＡＳＥ
０
ＳＤ
ＳＤ
ＳＤ
ＳＤ
ＳＤ
ＳＤ
ＳＤ
０
０
０
０
０
０
０
Ｖ ＰＨＡＳＥ
ＭＡＳＴＥＲ Ｈ ＰＨＡＳＥ
ＯＵＴ−３ Ｈ ＰＨＡＳＥ
ＳＣ ＰＨＡＳＥ ＣＯＡＲＳＥ
ＳＣ ＰＨＡＳＥ ＦＩＮＥ
ＥＮＣ Ｈ ＰＨＡＳＥ
ＰＭ Ｈ ＰＨＡＳＥ
ＳＹＮＣ ＯＵＴ Ｈ ＰＨＡＳＥ
ＳＹＮＣ ＯＵＴ Ｖ ＰＨＡＳＥ
Setting Item
SYNC CONT
Set Value
---
０
０
Description
The external synchronizing signal is not input. It is operating with the internal synchronization.
OFF
To the external synchronizing signal, both HDTV/SDTV output in the same phase.
GL +90H
HDTV Output : For output in 90H DELAY against external synchronization signal.
GL -90H
HDTV Output : For output in 90H ADVANCE for external synchronization signal.
SDTV output : For output in 42H DELAY against external synchronization signal.
SDTV output : For output in 42H ADVANCE for external synchronization signal.
HD V PHASE
SYS1
It adjusts the vertical phase of HDTV output line 1 signal to the external synchronization.
SYS2
It adjusts the vertical phase of HDTV output line 2 signal to the external synchronization.
HD TRUNK
It adjusts the vertical phase of HD TRUNK output signal to the external synchronization.
HD MASTER H PHASE
Changes
depending on
the FORMAT.
It adjusts the horizontal master phase of HDTV output signal to the external synchronization.
HD OUT-1 H PHASE
Changes
depending on
the FORMAT.
It adjusts the horizontal phase of HDTV OUT-1 output signal to the external synchronization.
HD OUT-2 H PHASE
Changes
depending on
the FORMAT.
It adjusts the horizontal phase of HDTV OUT-2 output signal to the external synchronization.
HD OUT-3 H PHASE
Changes
depending on
the FORMAT.
It adjusts the horizontal phase of HDTV OUT-3 output signal to the external synchronization.
HD PM H PHASE
Changes
depending on
the FORMAT.
It adjusts the horizontal phase of HDTV PM output signal to the external synchronization.
HD TRUNK H PHASE
Changes
depending on
the FORMAT.
It adjusts the horizontal phase of HDTV TRUNK output signal to the external synchronization.
・HD V PHASE SYS2 is enabled only when the simultaneous output is set to OUTPUT FORMAT.
Ex.) When OUT-1 is set to 1080P23PD and OUT-2 is set to 1080P23SF for OUTPUT FORMAT
1080P23PD output phase and 1080P23SF output phase can be set at SYS1 and SYS2 respectively.
74
BS-98 1409 VER1 (U) (E)
5.1
Setting Item
Set Value
Settings from the BS Menu
Description
SD V PHASE
0 to 524 or
0 to 624
It adjusts the vertical phase of SDTV output signal to the external synchronization.
SD MASTER H PHASE
-429 to 429
It adjusts the horizontal master phase of SDTV output signal to the external synchronization.
SD OUT-3 H PHASE
-428 to 429
It adjusts the horizontal phase of SDTV OUT-3 output signal to the external synchronization.
SD SC PHASE COARSE -100 to 100
It coarse adjustment the subcarrier phase of SDTV output signal to the external
synchronization.
SD SC PHASE FINE
-100 to 100
It coarse adjustment the subcarrier phase of SDTV output signal to the external
synchronization.
SD ENC H PHASE
-428 to 429
It adjusts the horizontal phase of SDTV ENC output signal to the external synchronization.
SD PM H PHASE
-428 to 429
It adjusts the horizontal phase of SDTV PM output signal to the external synchronization.
SYNC OUT H PHASE
Changes
depending on
the FORMAT.
It adjusts the horizontal phase of the external synchronization output (SYNC OUT).
SYNC OUT V PHASE
Changes
depending on
the FORMAT.
It adjusts the vertical phase of the external synchronization output (SYNC OUT).
・SDTV output is optional. When an optional is not mounted, the phase adjusting item of SDTV displays "---", and selecting
becomes disabled.
BS-98 1409 VER1 (U) (E)
75
5.1
Settings from the BS Menu
AUDIO MANAGEMENT
AUDIO MANAGEMENT sets the audio output.
＊＊＊ ＥＮＧＩＮＥＥＲ（１／２） ＊＊＊
▲
ＳＹＳＴＥＭ ＦＯＲＭＡＴ
ＯＵＴＰＵＴ ＦＯＲＭＡＴ
ＲＥＴ ＶＩＤＥＯ ＦＯＲＭＡＴ
ＰＨＡＳＥ ＣＯＮＴＲＯＬ
ＭＩＣ ＭＡＮＡＧＥＭＥＮＴ
ＩＮＣＯＭ ＭＡＮＡＧＥＭＥＮＴ
▼
To position the flashing cursor on the "MIC
MANAGEMENT", and determine.
Setting Item
HD SYS EMBEDDED
ＭＩＣ ＭＡＮＡＧＥＭＥＮＴ
ＨＤ ＳＹＳ ＥＭＢＥＤＤＥＤ
ＨＤ ＯＵＴ−１
ＨＤ ＯＵＴ−２
ＨＤ ＯＵＴ−３
ＨＤ ＰＭ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＳＤ ＳＹＳ ＥＭＢＥＤＤＥＤ
ＳＤ ＳＤＩ
ＳＤ ＰＭ
ＯＦＦ
ＯＦＦ
The submenu "MIC MANAGEMENT"
is displayed, on which you can perform
various settings.
Set Value
Description
ALL ON/OFF
Sets whether to embed audio signal to all HDTV outputs.
HD OUT-1
ON/OFF
Sets whether to embed audio signal to HDTV OUT-1 outputs.
HD OUT-2
ON/OFF
Sets whether to embed audio signal to HDTV OUT-2 outputs.
HD OUT-3
ON/OFF
Sets whether to embed audio signal to HDTV OUT-3 outputs.
HD PM
ON/OFF
Sets whether to embed audio signal to HDTV PM OUT outputs.
ALL ON/OFF
Sets whether to embed audio signal to all SDTV outputs.
SD SYS EMBEDDED
SD SDI
ON/OFF
Sets whether to embed audio signal to SDTV OUT-3 outputs.
SD PM
ON/OFF
Sets whether to embed audio signal to SDTV PM OUT outputs.
MASTER DELAY
HD SYS DELAY
0 to 21
It sets the audio signal delay amount of all systems.
0 to 21
It sets the audio signal delay amount of the HDTV system.
SD SYS DELAY
0 to 21
It sets the audio signal delay amount of the SDTV system.
DIGITAL DELAY
0 to 21
It sets the digital audio output delay amount.
0 to 21
It sets the analog audio output delay amount.
MIC1 OUTPUT LEVEL
MIC1/2 OUT DELAY
0dB/4dB
It sets the MIC1 OUT output standard level (0 dB/4 dB).
MIC1 LVL ADJ (0dB)
1 to 1023
It sets the MIC1 OUT 0dB setting level.
It sets the MIC1 OUT 4dB setting level.
MIC1 LVL ADJ (4dB)
1 to 1023
MIC2 OUTPUT LEVEL
0dB/4dB
It sets the MIC2 OUT output standard level (0 dB/4 dB).
MIC2 LVL ADJ (0dB)
1 to 1023
It sets the MIC2 OUT 0dB setting level.
MIC2 LVL ADJ (4dB)
1 to 1023
It sets the MIC2 OUT 4dB setting level.
MIC1 CENTER ADJ
EXECUTE/CANCEL
It adjusts the center OFFSET of the external MIC1 GAIN REMOTE control voltage.
MIC2 CENTER ADJ
EXECUTE/CANCEL
It adjusts the center OFFSET of the external MIC2 GAIN REMOTE control voltage.
・MIC1/2 CENTER ADJ function
The microphone gain from the potentiometer connected to external system by the MIC GAIN REMOTE function to the camera
head can be changed continuously. However, there are cases that the mechanical and electrical center values and the control
voltage do not match depending on the potentiometer performance and features of each unit. In this case, the MAX/MIN control
amount becomes one-sided to the center value.
This function is to offset to the mechanical center position of the potentiometer to the center of the control value.
Generally, this setting is conducted at the factory, and adjustment is not required. If "CENTER ADJ" is executed at a wrong
position, the control range becomes abnormal. Pay close attention when adjusting.
76
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
INCOM MANAGEMENT
INCOM MANAGEMENT sets the intercom output.
＊＊＊ ＥＮＧＩＮＥＥＲ（１／２） ＊＊＊
▲
ＳＹＳＴＥＭ ＦＯＲＭＡＴ
ＯＵＴＰＵＴ ＦＯＲＭＡＴ
ＲＥＴ ＶＩＤＥＯ ＦＯＲＭＡＴ
ＰＨＡＳＥ ＣＯＮＴＲＯＬ
ＭＩＣ ＭＡＮＡＧＥＭＥＮＴ
ＩＮＣＯＭ ＭＡＮＡＧＥＭＥＮＴ
▼
ＩＮＣＯＭ ＭＡＮＡＧＥＭＥＮＴ
ＥＮＧ
ＥＮＧ−ＩＮＰＵＴ
ＥＮＧ−ＯＵＴＰＵＴ
ＰＲＯＤ
ＰＲＯＤ−ＩＮＰＵＴ
ＰＲＯＤ−ＯＵＴＰＵＴ
Ｉ／Ｆ
ＴＥＲＭ
ＬＯＡＤ
Ｉ／Ｆ
ＴＥＲＭ
ＬＯＡＤ
ＥＮＧ−ＰＲＯＤ ２ＬＩＮＥ／１ＬＩＮＥ ２ＬＩＮＥ
ＦＲＯＮＴ ＩＮＣＯＭ
To position the flashing cursor on the
"INCOM MANAGEMENT", and
determine.
Setting Item
ENG IF
ENG-INPUT TERM
(Valid only 4W setting)
４Ｗ
６００
−−−
４Ｗ
６００
−−−
ＤＹＮＡＭＩＣ
The submenu "INCOM MANAGEMENT"
is displayed, on which you can perform
various settings.
Set Value
Description
4W
It sets Engineer line intercom system in 4-wire.
RTS
It sets Engineer line intercom system in RTS.
CC
It sets Engineer line intercom system in Cler-Com.
600
It sets Input termination impedance of the Engineer line intercom system in 600.
10k
It sets Input termination impedance of the Engineer line intercom system in 10k.
ENG-OUTPUT LOAD
OPEN
(Valid only RTS/CC setting)
200
It sets system impedance setting of the Engineer line RTS/Cler-Com in OPEN.
PROD IF
4W
It sets Producer line intercom system in 4-wire.
RTS
It sets Producer line intercom system in RTS.
PROD-INPUT TERM
(Valid only 4W setting)
It sets system impedance setting of the Engineer line RTS/Cler-Com in 200.
CC
It sets Producer line intercom system in Cler-Com.
600
It sets Input termination impedance of the Producer line intercom system in 600.
10k
It sets Input termination impedance of the Producer line intercom system in 10k.
PROD-OUTPUT LOAD
OPEN
(Valid only RTS/CC setting)
200
It sets system impedance setting of the Producer line RTS/Cler-Com in OPEN.
ENG-PROD 2LINE/1LINE
This is the setting when the line system is used as individual two lines of Engineer/Producer.
FRONT INCOM
2LINE
It sets system impedance setting of the Producer line RTS/Cler-Com in 200.
1LINE
Integrate Producer line to Engineer line to make them to one line.
DYNAMIC
It sets headset microphone to be connected to the front of the instrument in DYNAMIC type.
CARBON
It sets headset microphone to be connected to the front of the instrument in CARBON type.
ECM
It sets headset microphone to be connected to the front of the instrument in ECM type.
MIC POWER SUPPLY
ON/OFF
It sets whether or not the power is supplied when the microphone is set to EMC.
PGM1 TERM
600
It sets line termination impedance of the Program Audio #1 in 600.
10k
It sets line termination impedance of the Program Audio #1 in 10k.
PGM1 INPUT LEVEL
PGM2 TERM
PGM2 INPUT LEVEL
PGM3 TERM
PGM3 INPUT LEVEL
PGM MIX FRONT INCOM
4dB
It sets input level of the Program Audio #1 in +4dBs.
0dB
It sets input level of the Program Audio #1 in 0dBs.
-20dB
It sets input level of the Program Audio #1 in -20dBs.
600
It sets line termination impedance of the Program Audio #2 in 600.
10k
It sets line termination impedance of the Program Audio #2 in 10k.
4dB
It sets input level of the Program Audio #2 in +4dBs.
0dB
It sets input level of the Program Audio #2 in 0dBs.
-20dB
It sets input level of the Program Audio #2 in -20dBs.
600
It sets line termination impedance of the Program Audio #3 in 600.
10k
It sets line termination impedance of the Program Audio #3 in 10k.
4dB
It sets input level of the Program Audio #3 in +4dBs.
0dB
It sets input level of the Program Audio #3 in 0dBs.
-20dB
It sets input level of the Program Audio #3 in -20dBs.
OFF/PGM1,2,3
PGM -> FR-INCOM LEVEL x0.00 to 2.00
It sets whether or not the PGM is mixed to the INCOM output at the HEADSET.
It sets level of PGM to mix in INCOM output at the HEADSET.
BS-98 1409 VER1 (U) (E)
77
5.1
Settings from the BS Menu
Note:
・Setting of ENG/PROD IF and Items that can be linked
ENG/PROD IF
4W
RTS
INPUT TERM
600 / 10k
---
Cler-Com
---
OUTPUT LOAD
---
OPEN / 200
OPEN / 200
Generally, OUTPUT LOAD is set to "OPEN". When BS/CCU is detached from the external system, set to "200".
・Setting of FRONT INCOM and Items that can be linked
FRONT INCOM
DYNAMIC
CARBON
ECM
MIC POWER SUPPLY
Fixed to OFF
Fixed to ON
ON / OFF
Input level (Hidden)
-60dBu
-10dBu
-40dBu
Set according to the microphone type of the headset to be used.
78
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
HDTV VIDEO PROCESS
HDTV VIDEO PROCESS sets the various HDTV video processes.
＊＊＊ ＥＮＧＩＮＥＥＲ（２／２） ＊＊＊
▲
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
▼
To position the flashing cursor on
the "HDTV VIDEO PROCESS", and
determine.
Setting Item
GAMUT CLIP
LEVEL
HDTV BARS TYPE
ARIB BARS TYPE
SMPTE BARS TYPE1
SMPTE BARS TYPE2
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＧＡＭＵＴ ＣＬＩＰ
ＬＥＶＥＬ
−−−
−−−
ＨＤＴＶ ＢＡＲＳ ＴＹＰＥ
ＡＲＩＢ ＢＡＲＳ ＴＹＰＥ
ＳＭＰＴＥ ＢＡＲＳ ＴＹＰＥ１
ＳＭＰＴＥ ＢＡＲＳ ＴＹＰＥ２
ＳＭＰＴＥ
−−−
７５％
０％
ＣＨＡＲ ＬＥＶＥＬ
ＣＨＡＲ ＢＧ ＬＥＶＥＬ
−−−
−−−
The submenu "HDTV VIDEO PROCESS"
is displayed, on which you can perform
various settings.
Set Value
ON
Description
Sets ON / OFF of GAMUT CLIP.
98.0% to 109.0%
Sets CLIP LEVEL of GAMUT CLIP ON time.
SMPTE
Sets the HDTV color bar complying with the SMPTE-standard color bar.
ARIB
Sets the HDTV color bar complying with the ARIB-standard multi-format color bar.
100/75
Sets the HDTV color bar complying with the 100/0/75/0 color bar.
100/100
Sets the HDTV color bar complying with the 100/0/100/0 color bar.
75/75
Sets the HDTV color bar complying with the 75/0/75/0 color bar.
75%
Sets the pattern 2 of the ARIB-standard color bar to "75% White".
100%
Sets the pattern 2 of the ARIB-standard color bar to "100% White".
+I
Sets the pattern 2 of the ARIB-standard color bar to "+I signal".
75%
Sets the pattern 2 of the SMPTE-standard color bar to "75% White".
100%
Sets the pattern 2 of the SMPTE-standard color bar to "100% White".
+I
Sets the pattern 2 of the SMPTE-standard color bar to "+I signal".
-I
Sets the pattern 2 of the SMPTE-standard color bar to "-I signal".
0%
Sets the pattern 3 of the SMPTE-standard color bar to "0% Black".
+Q
Sets the pattern 3 of the SMPTE-standard color bar to "+Q signal".
CHAR LEVEL
-----
Sets the character level of the HDTV OUT signals. Sets in the factory.
CHAR BG LEVEL
-----
Sets the background level of characters on the HDTV OUT signals. Factory setting.
BS-98 1409 VER1 (U) (E)
79
5.1
Settings from the BS Menu
SDTV VIDEO PROCESS
SDTV VIDEO PROCESS sets the various SDTV video processes.
＊＊＊ ＥＮＧＩＮＥＥＲ（２／２） ＊＊＊
▲
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
▼
To position the flashing cursor on the
"SDTV VIDEO PROCESS", and determine.
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＶ ＳＬＩＭ ＤＴＬ ＴＹＰＥ
Ｖ ＳＬＩＭ ＤＴＬ ＦＲＥＱ
ＦＩＮＥ ＤＴＬ
ＣＯＭＢ
ＣＯＭＢ ＧＡＩＮ
Ｈ ＦＩＬＴＥＲ
Ｖ ＦＩＬＴＥＲ
ＭＯＴＩＯＮ ＤＥＴＥＣＴ
ＧＡＭＵＴ ＣＬＩＰ
ＬＥＶＥＬ
Ｈ ＯＮＬＹ
Ａ
−−−
−−−
−−−
ＮＯＲＭＡＬ
ＮＯＲＭＡＬ
ＭＵＳＩＣ
−−−
−−−
The submenu "SDTV VIDEO PROCESS"
is displayed, on which you can perform
various settings.
Note:
SPRC module is an option.
Selecting this item becomes disabled when the SPRC module is not implemented.
Setting Item
HV SLIM DTL TYPE
Set Value
Description
H ONLY
Sets SLIM DTL to be effective only in the horizontal direction.
V ONLY
Sets SLIM DTL to be effective only in the vertical direction.
H+V
Sets SLIM DTL to be effective both in the horizontal/vertical direction.
A
Sets a boost band.Number of effective lines × 0.41
B
Sets a boost band.Number of effective lines × 0.38
C
Sets a boost band.Number of effective lines × 0.36
D
Sets a boost band.Number of effective lines × 0.34
FINE DTL *2
0 to 8
Sets the effect of FINE DTL.
COMB
-
COMB FILTER. Sets in the factory. (option)
COMB GAIN
-
COMB FILTER GAIN. Sets in the factory. (option)
H FILTER *3
NARROW
Sets the horizontal filter.
The frequency characteristics improve in the order of "NARROW" < "NORMAL" < "WIDE"
< "SUPER".
V SLIM DTL FREQ *1
NORMAL
WIDE
SUPER
V FILTER
NARROW
NORMAL
Sets the vertical filter.
The frequency characteristics improve in the order of "NARROW" < "NORMAL" < "WIDE"
< "SUPER".
WIDE
SUPER
MOTION DETECT
Sets the motion detection function of the down-converter.
MUSIC
Specifies the normal mode. It is suitable for the shooting of the music program.
DRAMA
Suitable for still-image editing using a VTR in a drama. This remains a few afterimages
because framing is done.
STILL
Suitable for shooting still images such as picture shooting.
OFF
Suitable for shooting from a helicopter. Neither afterimages nor images remain because
field handling is done.
SPORTS
Suitable for broadcasting quick-motion sports.
GAMUT CLIP
LEVEL
ON
Sets ON / OFF of GAMUT CLIP.
98.0% to 109.0%
Sets CLIP LEVEL of GAMUT CLIP ON time.
SDTV SETUP SEL
-
Sets in the factory. (option)
CHAR LEVEL
0 to 200
Sets the character level of the SDTV OUT signals. Sets in the factory.
CHAR BG LEVEL
-100 to 100
Sets the background level of characters on the SDTV OUT signals. Sets in the factory.
*1 When "SLIM DTL" is "OFF" or SLIM DTL is set to be effective only in the horizontal direction ("H ONLY" is set to "HV SLIM
DTL TYPE"), the frequency to boost is half the number of effective lines.
*2 It is enabled only when the camera head to be connected is compatible with the module.
*3 When the format of the camera head is 720P59.94, only "NORMAL" can be selected.
80
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
HD PM VIDEO PROCESS
HD PM VIDEO PROCESS sets the various HDTV PM video processes.
＊＊＊ ＥＮＧＩＮＥＥＲ（２／２） ＊＊＊
▲
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
▼
To position the flashing cursor on the "HD
PM VIDEO PROCESS", and determine.
Setting Item
CHAR LEVEL
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＣＨＡＲ ＬＥＶＥＬ
ＣＨＡＲ ＢＧ ＬＥＶＥＬ
８０
５０
ＣＡＭ ＨＥＡＤ ＳＴＡＴＵＳ ＤＩＳＰ ＯＦＦ
ＤＩＳＰ ＰＯＳＩＴＩＯＮ
ＵＰ
The submenu "HD PM VIDEO PROCESS"
is displayed, on which you can perform
various settings.
Set Value
Description
0 to 100
It sets the character level of the HDTV PM OUT signal.
0 to 100
It sets the character background level of the HDTV PM OUT signal.
CAM HEAD STATUS DISPLAY
ON / OFF
It sets whether or not the status of the camera head is view on PM OUT.
DISP POSITION
UP
Set the character display position at the top.
DOWN
Set the character display position at the bottom.
UP L
Set the character display position at the top left.
DOWN L
Set the character display position at the bottom left.
UP R
Set the character display position at the top right.
DOWN R
Set the character display position at the bottom right.
BS-98 1409 VER1 (U) (E)
81
5.1
Settings from the BS Menu
SD PM VIDEO PROCESS
SD PM VIDEO PROCESS sets the various SDTV PM video processes. (* option)
＊＊＊ ＥＮＧＩＮＥＥＲ（２／２） ＊＊＊
▲
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
▼
To position the flashing cursor on the "SD
PM VIDEO PROCESS", and determine.
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＣＨＡＲ ＬＥＶＥＬ
ＣＨＡＲ ＢＧ ＬＥＶＥＬ
１２０
−３６
The submenu "SD PM VIDEO PROCESS"
is displayed, on which you can perform
various settings.
Note:
SPRC module is an option.
Selecting this item becomes disabled when the SPRC module is not implemented.
Setting Item
Set Value
Description
CHAR LEVEL
0 to 200
Sets the character level of the SD PM OUT signals.
CHAR BG LEVEL
-100 to 100
Sets the background level of characters on the SD PM OUT signals.
82
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
FUNCTION SETTING
FUNCTION SETTING sets the various function settings.
＊＊＊ ＥＮＧＩＮＥＥＲ（２／２） ＊＊＊
▲
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
▼
To position the flashing cursor on the
"FUNCTION SETTING", and determine.
Setting Item
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＡＲＣＮＥＴ ＩＤ ＳＥＴ
ＣＡＭ ＰＧＭ ＮＯ． ＥＮＡＢＬＥ
ＣＡＭ ＰＧＭ ＮＯ． ＳＥＴ
ＢＳ ＦＲＯＮＴ ＩＤ ＤＩＳＰＬＡＹ
１
ＯＦＦ
−−−
ＯＦＦ
ＰＭ ＴＡＬＬＹ ＳＥＬ
Ｙ
ＣＡＭ ＣＯＤＥ
ＳＡＦＥＴＹ＆Ｈ．ＰＷＲ
ＲＥＰＥＡＴＥＲ ＭＯＤＥ
−−−
−−−
−−−
The submenu "FUNCTION SETTING"
is displayed, on which you can perform
various settings.
Set Value
Description
ARCNET ID SET
1 to 255
Sets the NETWORK ID of ARCNET (10 decimal).
CAM PGM NO. ENABLE
OFF / ON
It sets whether or not the camera program number is controlled by CCU/BS.
CAM PGM NO. SET
OFF / 1 to 99
Sets the camera program number.
BS FRONT ID DISPLAY
OFF
The seven segment displays at the front side of the equipment do not display anything.
ARC ID
The seven segment displays at the front side of the equipment displays ARCNET
NETWORK ID (HEX).
PGM NO.
The seven segment display at the front side of the equipment displays the camera
program number.
PM TALLY SEL
Y
Assign the TALLY OUT (PM TALLY) pin "C" to the Y TALLY control.
COMM
Assign the TALLY OUT (PM TALLY) pin "C" to the Red/Green TALLY common control.
CAM CODE
−
Regional options
SAFETY&H.PWR
−
Regional options
REPEATER MODE
−
Regional options
CAM PWR CONT
−
Regional options
Q-TV MODE
Changes
depending on the
FORMAT.
It set and displays the analog QTV band width and the number of channels.
HD TRUNK
ON / OFF / ---
ON/OFF setting of the HDTV TRUNK VIDEO line. It is enabled only when the 3Gcompatible camera is connected and when the 1.5G format is operating.
HD Q-TV
ON / OFF / ---
ON/OFF setting of the HDTV QTV VIDEO line. It is enabled only when the 3G-compatible
camera is connected.
WARNING BIG CHAR
OFF / ON
The warning item for the self-diagnosis result (DIAGNOSTIC INFORMATION) is displayed
in a big character.
FIBER SINGLE MODE
OFF / ON
It sets ON/OFF of the fiber single mode.
For ARCNET and the camera program number, refer to the manuals of the control panel and the camera head that correspond to
the network.
NOTE:
Turn on the "HEAD POWER" switch of the front panel of CCU whenever CCU operaters "FIBER SIGNAL MODE".
BS-98 1409 VER1 (U) (E)
83
5.1
Settings from the BS Menu
ENGINEER SET FILE RENEW
The user registers and updates the memory (file) to back up the CCU/BS setting.
Note:
ENGINEER SET FILE
Up to three setting statuses of the equipment that the user customized can be saved in the internal memory. The data registered and
updated here can be invoked from "PRESET FILE LOAD" on the first page of MENU.
＊＊＊ ＥＮＧＩＮＥＥＲ（２／２） ＊＊＊
▲
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
▼
To position the flashing cursor on the
"ENGINEER SET FILE RENEW", and
determine.
1
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＦＩＬＥ ＳＥＬＥＣＴ
ＥＮＧＩＮＥＥＲ−１
ＤＡＴＡ ＲＥＮＥＷ ＭＯＤＥ
The submenu "ENGINEER SET FILE
RENEW" is displayed, on which you can
perform various settings.
Set the blinking cursor to "FILE SELECT" and select a file to be created and updated.
Note:
The file is overwritten and updated.
2
Set the blinking cursor to "DATA RENEW MODE" and finalize.
At the lower section of the screen, "PUSH SET -> RENEW" is displayed.
When finalized, the target ENGINEER file is updated.
After writing the data, "COMPLETED" is displayed.
84
BS-98 1409 VER1 (U) (E)
5.1
Settings from the BS Menu
PASSWORD ENTRY
Protect the ENGINEER SET FILE RENEW function with a password.
This function becomes enabled when the PLS module S3-3 is on and displayed on the MENU, and selecting becomes enabled.
＊＊＊ ＥＮＧＩＮＥＥＲ（２／２） ＊＊＊
▲
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＰＡＳＳＷＯＲＤ ＥＮＴＲＹ
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
▼
To position the flashing cursor on the
"PASSWORD ENTRY", and determine.
ＰＡＳＳＷＯＲＤ ＥＮＴＲＹ
ＩＮＰＵＴ
： □□□□
ＲＥＮＥＷ
ＣＯＮＦＩＲＭ
： □□□□
： □□□□
（ＳＥＬ）
ＨＯＲＩＺ．
０１２３４５６７８９
▲
（ＮＥＸＴ）
ＴＯＰ．
Input the current password to "INPUT".
When inputting a password for the first
time, input "0000".
Set a new password to "RENEW" and then
input a same password to "CONFIRM".
Note:
The initial password is "0000". The PASSWORD ENTRY is displayed when S3 No.3 ON of the PULSE module or the password
except "0000" is registered.
In addition, this function is for preventing overwrite of the data by incorrect operation, and does not aim at perfect security.
BS-98 1409 VER1 (U) (E)
85
5.1
Settings from the BS Menu
PROGRAM UPDATE
PROGRAM UPDATE updates firmware of the CCU / BS.
＊＊＊ ＥＮＧＩＮＥＥＲ（２／２） ＊＊＊
▲
ＨＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤＴＶ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＨＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＳＤ ＰＭ ＶＩＤＥＯ ＰＲＯＣＥＳＳ
ＦＵＮＣＴＩＯＮ ＳＥＴＴＩＮＧ
ＥＮＧＩＮＥＥＲ ＳＥＴ ＦＩＬＥ ＲＥＮＥＷ
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
▼
To position the flashing cursor on the
"PROGRAM UPDATE", and determine.
Setting Item
CCU/BS ROM
1
ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ
ＣＣＵ ＲＯＭ
ＲＥＡＤＹ
Ｃｕｒｒｅｎｔ Ｖｅｒ ＳＴＲ−＊＊＊＊．＊＊．＊＊
The submenu "PROGRAM UPDATE"
is displayed, on which you can perform
various settings.
Set Value
Description
READY
Ready for update.
CANCEL
Cancels update.
EXECUTE
Update firmware of the CCU / BS.
Position the flashing cursor on "CCU/BS ROM", and determine.
Flashing cursor moves to the mode setting, and also the display of the mode setting value switches from "READY" to
"CANCEL".
2
- When "CANCEL" is selected, the setting is canceled and "PROGRAM UPDATE" exits.
- When "EXECUTE" is selected, the following screen is displayed.
＊＊＊ ＰＲＯＧＲＡＭ ＵＰＤＡＴＥ ＊＊＊
ＬＯＡＤ ＊＊＊−＊＊ ＲＤＦ ＦＩＬＥ
ＦＩＬＥ
：
ＭＯＤＥＬ
：
ＰＲＯＧ ＮＯ ：
ＣＨＫ ＳＵＭ ：
Please refer to manual control panel to be used.
86
BS-98 1409 VER1 (U) (E)
5.2
Settings Using Switches on the Module
5.2 Settings Using Switches on the Module
It is necessary to set hard switches of each module according to the external system connected to CCU/BS.
Tally Mode Settings
Set the mode of the tally control signal input to the COMMUNICATION connector on the rear of the CCU/BS.
Switching is executed with S1 to S3 of the IO module.
S1
S2
S3
IO Module
POWER
Switch No.
Function Name
Setting
MAKE
Description
S1
R TALLY
POWER
MAKE
Sets the R TALLY signal input to the CCU/BS to "make contact mode".
S2
G TALLY
POWER
Sets the G TALLY signal input to the CCU/BS to "POWER mode".
MAKE
Sets the G TALLY signal input to the CCU/BS to "make contact mode".
S3
Y TALLY
Sets the R TALLY signal input to the CCU/BS to "POWER mode".
POWER
Sets the Y TALLY signal input to the CCU/BS to "POWER mode".
MAKE
Sets the Y TALLY signal input to the CCU/BS to "make contact mode".
BS-98 1409 VER1 (U) (E)
87
5.2
Settings Using Switches on the Module
PGM Settings
It sets the PGM (program audio) signal and audio trunk signal to be input to CCU/BS.
Generally, the setting is executed from the CCU/BS menu, so the setting by using the following module switches is not necessary.
S8 S9 S10 S11
IO Module
OFF
S8-S11 4dB UP
ON
Switch No.
S8
S9
S10
S11
88
Function Name
PGM-1 4dB UP
PGM-2 4dB UP
PGM-3 4dB UP
TRUNK 4dB UP
Setting
Description
OFF
To the input of PGM-1 line, +4 dB UP OFF.
ON
To the input of PGM-1 line, +4 dB UP ON.
OFF
To the input of PGM-2 line, +4 dB UP OFF.
ON
To the input of PGM-2 line, +4 dB UP ON.
OFF
To the input of PGM-3 line, +4 dB UP OFF.
ON
To the input of PGM-3 line, +4 dB UP ON.
OFF
To the input of TRUNK line, +4 dB UP OFF.
ON
To the input of TRUNK line, +4 dB UP ON.
BS-98 1409 VER1 (U) (E)
S8
PGM-1 4dB UP
S9
PGM-2 4dB UP
S10
PGM-3 4dB UP
S11
TRUNK 4dB UP
TROUBLE SHOOTING
and MAINTENANCE
6
90
BS-98 1409 VER1 (U) (E)
6.1
Indicator on the Front of BS Lights
6.1 Indicator on the Front of BS Lights
The LED indicator on the front of the BS lights when the BS becomes abnormal. Take the following actions since the cause varies
depending on the indicator lit.
TEMP indicator
FAN ALARM indicator
(CABLE) SHORT indicator
(CABLE) OPEN indicator
OPTICAL LEVEL indicator
■ When the OPTICAL LEVEL indicator lights
Indicators next to "HEAD" indicate the reception status on the camera head side, and indicators next to "BS" indicate the reception
status on the BS side.
Cause
Action
The optical connector must be dirty.
The lighting state of the OPTICAL LEVEL indicator changes.
Clean the optical connector end of the cable or the equipment side.
■ When the (CABLE) OPEN indicator lights
Cause
Action
The (CABLE) OPEN indicator lights when the camera cable is not
connected or there is an open.
Check if the camera cable is properly connected or there is no open.
If there is an open, replace the camera cable with a new one.
■ When the (CABLE) SHORT indicator lights
Cause
Action
The (CABLE) SHORT indicator lights when a short circuit occurs in
the camera cable or a short circuit occurs in the optical connector
due to a cause such as water.
Check if a short circuit occurs in the camera cable or the optical
connector is dry.
If the optical connector is wet, dry it and then clean it.
■ When the FAN ALARM indicator lights
Cause
Action
FAN ALARM indicator will light when the fan is in internal BS has
stopped.
Check if the fans are normal.
If any of the fans is abnormal or the lifetime of the fan expires, replace
it with a new one.
■ When the TEMP indicator lights
Cause
Action
The TEMP indicator lights when the BS internal temperature is
abnormally high.
When this indicator lights on, check that the ventilation hole on the
front panel and the exhaust hole on the rear panel are not covered or
clogged with dust. Avoid a place with direct sunlight.
CAUTION:
If you disregard TEMP warning and temperature rises, it must be system reboot compulsorily due to device protection.
BS-98 1409 VER1 (U) (E)
91
6.1
Indicator on the Front of BS Lights
■ Cleaning Optical Connectors
The camera cable connecting the camera head and the CCU/BS transmits optical signals through 10μm core glass fibers. If
Ferrules, which secure glass fibers, are dirty or have dust on them, transmission loss (optical signal attenuation) occurs. If Ferrules
are extremely dirty, optical signals are interrupted and the camera cable may not work properly.
Regular cleaning of Ferrules is suggested if the camera connector is frequently removed and inserted. The figures below show the
shape of the camera connector joint section, location of the Ferrules, and how to clean the Ferrules:
●Camera Connector Joint Section
OPS Series
3K Series
Alignment sleeve:
Present only in female
connectors
Alignment sleeve
Screw: Hole only for male
connectors
Ferrules
Plug (female)
Ferrule
Top: Present only in
female connectors
Top
Jack (male)
Plug receptacle
(female receptacle)
Ferrule
Receptacle
(male receptacle)
Top
Plug (female)
Ferrule
Alignment sleeve
Ferrule
Ferrule
Jack (male)
Ferrule
Top
Top: Present only in
female connectors
Plug receptacle
(female receptacle)
Ferrule
Top
Alignment sleeve
Ferrule
Receptacle
(male receptacle)
Ferrule
Ferrule
●Plug/Jack for Camera Connectors
Receptacle
BS rear side
Jack
Plug
BREAKER
RET-1
RET-2
/MIC
Plug Receptacle
Clean the four sections: receptacle on the camera head, plug receptacle on the BS, and plug/jack on both ends of the camera cable.
The cleaning method for male connectors differs from that for female connectors.
92
BS-98 1409 VER1 (U) (E)
6.1
Indicator on the Front of BS Lights
■ OPS Series Connectors
The following explains how to clean Ferrules using a Tajimi OPS series camera cable plug (female) as an example.
1
Camera connector plug
(female)
Loosen the screw at the center of the connector with a
flat-blade screwdriver or a coin.
After turned 9 or 10 turns counterclockwise, the screw will
come out. The screw is not removed because it is attached to
the top.
Top
Flat-blade
screwdriver
2
Pull the screw and remove the top from the connector.
Camera cable
① Turn the screw
counterclockwise.
Screw
Screw
Top
② Pull the screw to remove the top from the connector.
3
Wipe the Ferrule with a cotton swab dampened with
alcohol.
CAUTION:
- When you wipe the Ferrule, move the cotton swab straight
in a way in which you brush the dust off the Ferrule. Do not
wipe back and forth or in a circle. Doing so may spread the
dirt instead of removing it.
- Do not carelessly blow your breath on the Ferrule.
Ferrule
③ Wipe with a cotton swab dampened
with alcohol.
Good example
Cross section
of Ferrule
4
After wiping the Ferrule with alcohol, wipe the Ferrule with a dry cotton swab.
5
Make sure that the dirt is removed.
Bad example
Cross section
of Ferrule
Use a loupe to examine the Ferrule.
6
If the Ferrule is free from dirt, align the top with the connector guide and put it back in the connector.
Be sure to push the top securely into the connector.
7
Tighten the screw with a flat-blade screwdriver or a coin.
Male connectors have no "top"; therefore, steps 1, 2, and 6 above are not required.
BS-98 1409 VER1 (U) (E)
93
6.1
Indicator on the Front of BS Lights
■ 3K Series Connectors
The following explains how to clean Ferrules using a Lemo 3K series camera cable plug (female) as an example.
CAUTION:
When removing the alignment sleeve, be sure to use a dedicated optical contact extractor (DCC.91.312.5LA). Also use the end of the
extractor that has an inner thread.
1
Prepare a dedicated extractor and place the extractor in a position parallel to the connector.
2
Remove the cap of section A (with a thread).
Section A
Extractor
Thread
3
② Remove the cap
Ferrule
Extractor
Insert the extractor into the alignment sleeve and turn
the extractor clockwise 8 to 10 turns until it stops. When
it stops, pull the extractor out straight.
Leave the alignment sleeve attached to the extractor.
Alignment sleeve
Alignment sleeve ③ Insert the extractor into the
alignment sleeve, turn, and
pull out.
4
Wipe the Ferrule with a cotton swab dampened with
alcohol.
CAUTION:
- When you wipe the Ferrule, move the cotton swab straight
in a way in which you brush the dust off the Ferrule. Do not
wipe back and forth or in a circle. Doing so may spread the
dirt instead of removing it.
- Do not carelessly blow your breath on the Ferrule.
Ferrule
④ Wipe with a cotton swab
dampened with alcohol.
Good example
5
6
After wiping the Ferrule with alcohol, wipe the Ferrule
with a dry cotton swab.
Cross section
of Ferrule
Bad example
Cross section
of Ferrule
Make sure that the dirt is removed.
Use a loupe to examine the Ferrule.
7
8
Wipe the electrical contact and alignment sleeve in the same way.
Insert the alignment sleeve into the optical contact until it clicks and turn the extractor counterclockwise 8 to 10
turns.
The extractor is removed from the alignment sleeve.
Male connectors have neither "top" nor "alignment sleeve"; therefore, steps 1 to 3 and 8 above are not required.
94
BS-98 1409 VER1 (U) (E)
6.2
ALARM Indicator on the Control Panel Flashes ON and OFF
6.2 ALARM Indicator on the Control Panel Flashes ON and OFF
The BS-98 is equipped with a self diagnostic function which monitors whether the BS and camera head are running normal. As
soon as the BS power is turned ON, the self diagnostic function starts running, and always runs during operation.
If the BS or camera head becomes abnormal, the diagnostic function immediately detects the abnormality, and the ALARM
indicator on the control panel flashes ON and OFF. At this time, the self diagnostic information is displayed on the Picture Monitor,
so that you can locate the abnormal point.
Note:
Even if the ALARM indicator does not flash, you can check whether BS and camera are running normal by pressing the PM IND/
PAGE switch on the control panel twice to display the self diagnostic information on the Picture Monitor.
OCP
MCP
OCP-200
CAM PWR VF PWR
PM IND PANEL
/ PAGE ENABLE
OFF
STANDARD CAP
BARS
CAL
TALLY
INFO
OPE
SETUP MAINTE
O
S
ABB
ABB
U
RANGE
SENS
CLS OPEN
±1 ±2
MASTER PED
KNOB
FREE
AWB
AWB
PM IND/PAGE button
USER WFM/PM
M
W
AUTO
IRIS
HEAD POWER
PREVIEW
OPT
HEAD
CCU
CABLE
OPEN
SHORT
ALARM
CALL
ALARM indicator
BS Self Diagnostic Information
■ Self Diagnostic Information Screen
The following is the Self Diagnostic Information Screen of the BS.
Diagnosed item
Diagnosis result
BS-98 1409 VER1 (U) (E)
95
6.2
ALARM Indicator on the Control Panel Flashes ON and OFF
■ List of Self Diagnostic Information
The following tables list the self diagnostic information for the standard specification.
List of Self Diagnostic Information
Diagnosed Item
Description
Diagnosis Result
Meaning
Head Power
Power status of the camera head
ON
The camera head is powered ON.
OFF
The camera head is powered OFF.
Head Fan
Rotating status of fan of the camera
head or FA (Fiber Adaptor)
AUTO SSLOW
Super-slow in auto mode
AUTO SLOW
Slow in auto mode
AUTO NOR
Normal in auto mode
AUTO FAST
Fast in auto mode
SSLOW
Super-slow in manual mode
SLOW
Slow in manual mode
NOR
Normal in manual mode
FAST
Fast in manual mode
NG
Fan has stop.
Internal temperature of the camera
head
OK
Normal
NG
The temperature is abnormally high or the
difference between the internal temperature
and outside-air temperature is at least 25°C.
Head Battery
Status of the battery in the MPU
module of the camera head
OK
Normal
Head Memory
Status of the RAM in the MPU module OK
of the camera head
NG
Normal
BS Fan
Rotating status of the fans on the rear
and inside of the BS
OK
Normal
NG
Internal cooling fan either has stopped.
BS Temp
Internal temperature of the BS
OK
Normal
NG
The temperature is abnormally high or the
difference between the internal temperature
and outside-air temperature is at least 25°C.
Status of the battery in the BS CONT/
REF module
OK
Normal
NG
The backup battery voltage is low.
Status of the RAM in the BS
MPU&REF module
OK
Normal
NG
Data in the module is destroyed.
Head Temp
BS Battery
BS Memory
BS >>> Head
(BS to Head
transmission)
Head >>> BS
(Head to BS
transmission)
96
OPT Level
NG
Optical signal level sent from the BS
OK
to the camera head (Detect the optical
ATTEN
receiving level at the camera head
side and display the status).
WARN
The backup battery voltage is low.
Data in the module is destroyed
Good
The amount of light received decreased.
The amount of light received significantly
decreased.
NG
Light cannot be received.
OK
The format is normal and there is no CRC error.
NG
The format is abnormal or there is a CRC error.
OK
Normal
NG
No command signals are sent, or a CPU error
occurs.
Optical signal level sent from the
camera head to the BS (Detect the
optical receiving level at the BS side
and display the status).
OK
Good
ATTEN
The amount of light received decreased.
WARN
The amount of light received significantly
decreased.
NG
Light cannot be received.
SDI Status
Status of SDI signal
OK
The format is normal and there is no CRC error.
NG
The format is abnormal or there is a CRC error.
Comm Status
Status of the command signal sent
from the camera head to the BS
OK
Normal
NG
No command signals are sent, or a CPU error
occurs.
SDI Status
Status of SDI signal
Comm Status
Status of the command signal sent
from the BS to the camera head
OPT Level
BS-98 1409 VER1 (U) (E)
6.2
Diagnosed Item
Cable Connection
ALARM Indicator on the Control Panel Flashes ON and OFF
Description
Diagnosis Result
Camera cable connection status
between the camera head and the BS
Meaning
OK
Normal
OPEN
Cable is not connected, or there is an open.
SHORT
A short circuit occurs in the cable.
Status of the safety signal sent from
the camera head to the BS
OK
Normal
NG
The safety signal is not received, or the
connected camera head is not supported by
this BS.
Status of the model identification
signal sent from the camera head to
the BS
OK
Normal
NG
The model identification signal is not received,
or the connected camera head is not supported
by this BS.
Power Tap (CCU only)
The tap status of the transformer for
power feeding to the camera head
inside of the CCU
1, 2, 3, 4
The voltage fed from CCU to the camera head
is higher in an order of 1 -> 2 -> 3 -> 4.
Genlock
Status of external SYNC signal
INT
No external SYNC signals are input (operation
is performed with internal SYNC signals.)
Internal mode
Safety signal
Head ID
10 Field Lock
System Format
NTSC
When external SYNC signal is NTSC
NTSC 10f
When external SYNC signal is NTSC +10
FIELD ID
1080P59
When external SYNC signal is 1080P59.94
1080I59
When external SYNC signal is 1080I59.94
1080P23
When external SYNC signal is 1080P23.98
1080P23SF
When external SYNC signal is 1080P23.98SF
1080P29
When external SYNC signal is 1080P29.97
720P59
When external SYNC signal is 720P59.94
PAL
When external SYNC signal is PAL
1080P50
When external SYNC signal is 1080P50
1080I50
When external SYNC signal is 1080I50
720P50
When external SYNC signal is 720P50
UNKNOWN
External SYNC signals are input, but
synchronization is not performed.
When the output format is "1080P23.
PD", "1080P23.SF" or "1080P23".,
output phase of first frame of
"1080P23". or "1080P23.PD" is either
locked or unlocked to external SYNC
signal.
LOCK
Locked to external SYNC signal.
UNLOCK
Unlocked to external SYNC signal.
It indicates FORMAT that is set with
SYSTEM FORMAT.
1080I59
1080I/59.94
1080P23PD
1080P/23.98 2-3 pulldown Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
1080P29SF
1080P/29.97
Segment frame Y Pb Pr 4:2:2
720P59
720P/59.94
Y Pb Pr 4:2:2
1080P59 3G
1080P/59.94 Y Pb Pr 4:2:2
1080I59 3G
1080I/59.94
1080P23PD 3G
1080P/23.98 2-3 pulldown G B R 4:4:4
G B R 4:4:4
1080P29SF 3G
1080P/29.97
1080I119 3G
1080I/119.88 Y Pb Pr 4:2:2
Segment frame G B R 4:4:4
720P119 3G
720/P119.88
1080I50
1080I/50
Y Pb Pr 4:2:2
1080P25SF
1080P/25
Segment frame Y Pb Pr 4:2:2
Y Pb Pr 4:2:2
720P50
720P/50
Y Pb Pr 4:2:2
1080P50 3G
1080P/50
Y Pb Pr 4:2:2
1080I50 3G
1080I/50
G B R 4:4:4
1080P25SF 3G
1080P/25
Segment frame G B R 4:4:4
1080I100 3G
1080I/100
Y Pb Pr 4:2:2
720P100 3G
720/P100
Y Pb Pr 4:2:2
BS-98 1409 VER1 (U) (E)
97
98
BS-98 1409 VER1 (U) (E)
CHANGING INFORMATION
CHANGING INFORMATION
This chapter contains the revision information of user-specific specification or design change requested by users.
Read by comparing this information with the main part of the maintenance manual.
BS-98 1409 VER1 (U) (E)
99
100
BS-98 1409 VER1 (U) (E)
BS-98
Base Station
OPERATION MANUAL
1st Edition : September 2014
Published by Ikegami Factory of
Ikegami Tsushinki Co., Ltd.
© September 2014
Ikegami Tsushinki Co., Ltd.
- All rights reserved. Reproduction or duplication, without permission of
Ikegami Tsushinki Co., Ltd. of editorial or pictorial content in whole or in part,
in any manner, is prohibited.
- Specifications and design are subject to change without prior notice.
Ikegami Tsushinki Co., Ltd.
5-6-16, Ikegami, Ohta-ku, Tokyo, 146-8567, Japan
Phone : +81-(0)3-5700-4114
Fax : +81-(0)3-5748-2200
E-Mail : info_e@ikegami.co.jp
URL : http://www.ikegami.co.jp/en/
Ikegami Electronics (U.S.A.),Inc.
37 Brook Avenue, Maywood, New Jersey 07607, U.S.A.
Phone : +1-201-368-9171
Fax : +1-201-569-1626
E-Mail : engineering@ikegami.com, service@ikegami.com
URL : http://www.ikegami.com
Ikegami Electronics (Europe) GmbH
Ikegami Strasse 1, D-41460 Neuss, GERMANY
Phone : +49-(0)2131-123-0
Fax : +49-(0)2131-102820
E-Mail : info@ikegami.de
URL : http://www.ikegami.de
Ikegami Electronics (Europe) GmbH - UK
Unit E1, Cologne Court, Brooklands Close,
Sunbury-on-Thames, Middlesex, TW16 7EB, UK.
Phone : +44-(0)1932-76 97 00
Fax : +44-(0)1932-76 97 10
E-Mail : technical@ikegami.co.uk , sales@ikegami.co.uk
Ikegami Electronics Asia Pacific Pte.LTD.
1 Tampines Central 5, #3-3 CPF Tampines Building, Singapore 529508
Phone : +65 6260-8820
Fax : +65 6260-8896
URL : http://sg.ikegami.co.jp/
Property of :