@A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51
This summary is for information only and is not approved for modification of the aircraft.
ATA SYSTEM: 25
TITLE:
EQUIPMENT/FURNISHINGS - CABIN ATTENDANT SEAT INSPECTION
OF THE BACKREST
**CONF ALL
MODIFICATIONS
None
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
Some Cabin Attendant Seat backrests were found to be non-compliant with the material hardness
specifications requirements. Due to a missing heat treatment of the sheet metal, the backrest can
permanently deform, thus preventing the closure of the seat pan. Due to its proximity with the exit
doors, the seat pan remaining open could interfere with the passengers egress routes.
This Service Bulletin calls for the inspection of the Cabin Attendant Seats backrests and the
replacement of the non-compliant with compliant backrests.
This Service Bulletin is published to advise operators of A320 and A321 aircraft of the issue of
Goodrich Interiors Service Bulletin Nos. 2427-25-001, 2428-25-001 and 2431-25-001.
Accomplishment of this Service Bulletin will contribute to avoid potential delay of passengers evacuation
due to the partial blockage of the path by the Cabin Attendant Seat pan.
GENERAL EVALUATION
COMPLIANCE
EVALUATION TABLE
RECOMMENDED (1)
CANCELS INSPECTION SB
NO
POTENTIAL AD
RELIABILITY AFFECTED
COST SAVING
STRUCTURAL LIFE EXTN
NO
NO
NO
NO
NO
NO
NO
YES
NOTE (1):
A/C OPERATION AFFECTED
PAX COMFORT AFFECTED
ETOPS AFFECTED
VENDOR SB INVOLVED
Service Bulletin recommended to be accomplished to prevent significant operational
disruptions.
MATERIAL PRICE INFORMATION
No Material
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 1
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
SUMMARY
EFFECTIVITY
This Service Bulletin is applicable to this (these) operator(s) :
DLH
EWE
FFT
NKS
VRD
WZZ
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU
OEB
AOT
SIL
ISI
LINE MAINTENANCE AFFECTED
LIFE LIMIT
OTHER
25.22.00.005
None
None
None
00.00.00198
No
None
None
NATURE OF THE WORK
AIRCRAFT
EQUIPMENT
HARD
SOFT
OBRM
NO
YES
NO
NO
NO
MANPOWER
Task 251BEK-832-848-001: Inspection
TOTAL MANHOURS
ELAPSED TIME (HOURS)
1.50
1.50
Additional manhours related to Vendor SB; refer to:
Modify the Cabin Attendant Seat
Goodrich Interiors Service Bulletin
No. 2431-25-001
Goodrich Interiors Service Bulletin
No. 2428-25-001
Goodrich Interiors Service Bulletin
No. 2427-25-001
APPENDICES
Appendix 01 - Affected Serial Numbers
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 2
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51
ATA SYSTEM: 25
TITLE:
EQUIPMENT/FURNISHINGS - CABIN ATTENDANT SEAT INSPECTION
OF THE BACKREST
MODIFICATION No.:
None
This document contains AIRBUS PROPRIETARY INFORMATION and shall at all times remain the
property of AIRBUS; no intellectual property right or licence is granted by AIRBUS in connection with
any information contained in it. It is delivered on the express condition that said document and the
information contained in it shall be treated as confidential, shall not be used for any purpose other than
that for which it is hereby delivered. It shall not be disclosed in whole or in part to third parties and shall
not be duplicated in any manner (except for the purposes of performing the tasks described hereunder
and provided that any recipient of such document shall comply with the conditions herein), without
AIRBUS prior written consent.
1.
PLANNING INFORMATION
**CONF ALL
A.
EFFECTIVITY
(1)
Models
320-214
(2)
321-211
321-231
Effectivity by MSN
6669 6672 6704 6736 6770 6773 6787 6793 6804 6825 6835 6838 6845 6848 6867
6889 6891 6897 6910 6926 6939 6947 6953 6976
(3)
Effectivity by Operator
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR
DLH
EWE
FFT
NKS
VRD
WZZ
6
MSN
6947
6953
6773
6672
6669
6848
6793
6736
6704
6910
6825 6838 6845 6891 6926
6770 6804 6867 6897
6787 6835 6889 6939
6976
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 1
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
(4)
Configuration by MSN
MSN
6669 6672 6704 6736 6770 6773 6787 6793 6804 6825 6835
6838 6845 6848 6867 6889 6891 6897 6910 6926 6939 6947
6953 6976
(5)
CONFIGURATION
001
Configuration definition
**CONF 001
Config. 001 is valid for all the aircraft given in the effectivity of this Service Bulletin as a
standard configuration.
(6)
Material Effectivity
None
B.
CONCURRENT REQUIREMENTS
None
C.
REASON
(1)
History
Some Cabin Attendant Seat backrests were found to be non-compliant with the material
hardness specifications requirements. Due to a missing heat treatment of the sheet
metal, the backrest can permanently deform, thus preventing the closure of the seat pan.
Due to its proximity with the exit doors, the seat pan remaining open could interfere with
the passengers egress routes.
(2)
Objective/Action
This Service Bulletin calls for the inspection of the Cabin Attendant Seats backrests and
the replacement of the non-compliant with compliant backrests.
This Service Bulletin is published to advise operators of A320 and A321 aircraft of
the issue of Goodrich Interiors Service Bulletin Nos. 2427-25-001, 2428-25-001 and
2431-25-001.
(3)
Advantages
Accomplishment of this Service Bulletin will contribute to avoid potential delay of
passengers evacuation due to the partial blockage of the path by the Cabin Attendant
Seat pan.
(4)
Operational/Maintenance Consequences
None
D.
DESCRIPTION
To accomplish this Service Bulletin it is necessary to :
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 2
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
Task 251BEK-832-848-001: Inspection
(1) Do a Check of the Cabin Attendant Seat Serial Numbers (SNs) and Part Numbers
(PNs)
(2) Modify the Cabin Attendant Seat
E.
COMPLIANCE
(1)
Classification
RECOMMENDED: Service Bulletin recommended to be accomplished to prevent
significant operational disruptions.
(2)
Accomplishment Timescale
Accomplishment of this Service Bulletin is recommended and is to be accomplished
within 24 months from the effective date of this Service Bulletin.
F.
APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G.
MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
The minimum manhours necessary to accomplish this Service Bulletin are those for the
Inspection. Depending on the inspection result, additional manhours can apply.
Task 251BEK-832-848-001: Inspection
Get Access
On Aircraft
Do a Check of the Cabin Attendant Seat Serial
Numbers (SNs) and Part Numbers (PNs)
0.50
Close-Up
0.50
TOTAL MANHOURS
ELAPSED TIME (HOURS)
0.50
1.50
1.50
Additional manhours related to Vendor SB; refer to:
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 3
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
Task 251BEK-832-848-001: Inspection
Modify the Cabin Attendant Seat
H.
Goodrich Interiors Service Bulletin
No. 2431-25-001
Goodrich Interiors Service Bulletin
No. 2428-25-001
Goodrich Interiors Service Bulletin
No. 2427-25-001
WEIGHT AND BALANCE
Not Changed
I.
ELECTRICAL LOAD DATA
Not Changed
J.
REFERENCES
Aircraft Maintenance Manual (AMM)
Elec. Std. Practices Manual (ESPM)
Vendor Service Bulletin (VSB)
K.
06-20-00
06-31-53
12-34-24
20-55-00
Goodrich Interiors Service Bulletin
No. 2427-25-001
Goodrich Interiors Service Bulletin
No. 2428-25-001
Goodrich Interiors Service Bulletin
No. 2431-25-001
PUBLICATION AFFECTED
None
L.
INTERCHANGEABILITY/MIXABILITY
Not Applicable
M.
SPARES
None
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 4
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
2.
MATERIAL INFORMATION
**CONF ALL
A.
MATERIAL - PRICE AND AVAILABILITY
(1)
Procurement Addresses
Vendor parts are to be procured from Goodrich Interiors in accordance with Goodrich
Interiors Service Bulletin Nos. 2427-25-001, 2428-25-001 and 2431-25-001.
(2)
Price and Availability
No AIRBUS kit will be provided.
Refer to the Goodrich Interiors Service Bulletin Nos. 2427-25-001, 2428-25-001 and
2431-25-001 for the equipment modification sales terms.
B.
INDUSTRY SUPPORT INFORMATION
AIRBUS will not provide industry support for accomplishment of this Service Bulletin.
Refer to the Goodrich Interiors Service Bulletin Nos. 2427-25-001, 2428-25-001 and
2431-25-001 for the industry support terms of the Vendor Service Bulletin parts and labor.
This Service Bulletin is the subject of an AIRBUS monitored retrofit campaign.
For the organisation of this retrofit, you are kindly requested to contact AIRBUS retrofit
management department.
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
France
E-mail: monitored.retrofit@airbus.com
C.
LIST OF COMPONENTS
No Kit
D.
LIST OF MATERIALS - OPERATOR SUPPLIED
None
E.
PARTS TO BE RE-IDENTIFIED BY OPERATOR
Parts are re-identified in accordance with the Goodrich Interiors, Service Bulletin Nos
2427-25-001, 2428-25-001 and 2431-25-001.
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 5
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
F.
TOOLING
None
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 6
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
3.
ACCOMPLISHMENT INSTRUCTIONS
Task 251BEK-832-848-001 - Inspection
WARNING:
MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
CAUTION:
ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP
ELECTRICAL WIRING IN A SATISFACTORY CONDITION (ELECTRICALLY
AND MECHANICALLY SERVICEABLE). WHEN YOU DO MAINTENANCE
WORK, REPAIRS OR MODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING,
COMPONENTS AND THE WORK AREA AS CLEAN AS POSSIBLE. TO DO
THIS:
-
PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC. AS
NECESSARY ON WIRING AND COMPONENTS.
-
REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND
OTHER CONTAMINATION.
THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION
AND DAMAGE TO THE ELECTRICAL WIRING INSTALLATION.
IF THERE IS CONTAMINATION, REFER TO ESPM 20-55-00.
NOTE:
The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE:
The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE:
Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE:
The purpose of flowcharts is to supplement the information given in the Procedure
and Compliance paragraphs and not to serve as the primary source for tasks or
compliance times given in this Service Bulletin.
NOTE:
This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact AIRBUS for further
instructions and approval
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 7
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
Task Associated Data
Zone
200
Manpower
TOTAL MANHOURS
ELAPSED TIME (HOURS)
1.50
1.50
Additional manhours related to Vendor SB; refer to:
Goodrich Interiors Service Bulletin No. 2431-25-001
Goodrich Interiors Service Bulletin No. 2428-25-001
Goodrich Interiors Service Bulletin No. 2427-25-001
A.
GENERAL
(1)
Subtask 251BEK-910-201-001 - Standard Practices
Manpower Resources
Skills
NON SPECIFIC
Aircraft Maintenance Manual (AMM)
(2)
References
06-20-00, Page Block 001
06-31-53, Page Block 001
(a)
For Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b)
For the identification of zones, refer to AMM 06-20-00, Page Block 001.
Subtask 251BEK-839-201-001 - Administrative
Manpower Resources
Skills
NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
B.
PREPARATION
(1)
Subtask 251BEK-941-201-001 - Job Set-up
Manpower Resources
Skills
NON SPECIFIC
Aircraft Maintenance Manual (AMM)
NOTE:
The items given in this note shall be considered as the basic Aircraft
configuration before you start a maintenance task:
-
6
References
Task 12-34-24-869-802
Aircraft on the ground resting on landing gear (the ground safety
locks and the wheel chocks are in position on the landing gear)
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 8
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
(a)
C.
-
Engine shut down, thrust reversers closed and locked
-
Aircraft in clean configuration
-
Parking brake applied
-
Aircraft electrical network de-energized
-
Hydraulic systems depressurized
-
Access to the cockpit and cabin is available
-
All circuit breakers are in closed position
-
All controls in NORM, AUTO or OFF position.
Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-869-802.
PROCEDURE
(1)
Subtask 251BEK-210-201-001 - Do a Check of the Cabin Attendant Seat Serial
Numbers (SNs) and Part Numbers (PNs)
Work Zones and Access Panels
Access/Work location
Zone
200
Manpower Resources
Manhours
Minimum number of person
0.50
1
Subtask elapsed time
0.50
Skills
NON SPECIFIC
References
Sheet 01
Fig. A-GFAAA
Flowchart
(a)
6
Do a check of all the Cabin Attendant Seat Serial Numbers (SNs) and Part
Numbers (PNs), refer to Fig. A-GFAAA Sheet 01.
1
For Cabin Attendant Seats with affected SNs and PNs, refer to Appendix 01 Affected Serial Numbers , replace the non conforming backrest in accordance
with the applicable VSB, go to SUBTASK 251BEK-831-201 001 Modify the
Cabin Attendant Seat .
2
If there are no Cabin Attendant Seats model 2427, 2428 or 2431, no further
action is required with this Service Bulletin, go to SUBTASK 251BEK-942-201
001 Close-up .
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 9
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
(2)
Subtask 251BEK-831-201-001 - Modify the Cabin Attendant Seat
Zone
200
Work Zones and Access Panels
Access/Work location
References
Goodrich Interiors 2427-25-001
Goodrich Interiors 2428-25-001
Goodrich Interiors 2431-25-001
Sheet 01
Vendor Service Bulletin (VSB)
Fig. A-GRAAA
Reporting Sheet
D.
(a)
For Cabin Attendant Seats model 2431, modify in accordance with Goodrich
Interiors Service Bulletin No. 2431-25-001.
(b)
For Cabin Attendant Seats model 2428, modify in accordance with Goodrich
Interiors Service Bulletin No. 2428-25-001.
(c)
For Cabin Attendant Seats model 2427, modify in accordance with Goodrich
Interiors Service Bulletin No. 2427-25-001.
(d)
Complete the report sheet, refer to Fig. A-GRAAA Sheet 01 and send to AIRBUS.
TEST
None
E.
CLOSE-UP
(1)
Subtask 251BEK-942-201-001 - Close-up
Manpower Resources
Skills
6
NON SPECIFIC
(a)
Make sure that the work areas are clean and clear of tools and other items of
equipment.
(b)
Put the aircraft back to its initial configuration.
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 10
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
**CONF ALL
CHECK UTAS SEATS PART NUMBER AND SERIAL
NUMBER FITTED ON INVOLVED AIRCRAFT
SEAT
PART NUMBER
AND SERIAL NUMBER
IS AFFECTED?
NO
YES
FOR SEATS WITH PART NUMBER 2431
MODIFY IN ACCORDANCE WITH
VSB NO. 2431−25−001
FOR SEATS WITH PART NUMBER 2428
MODIFY IN ACCORDANCE WITH
VSB NO. 2428−25−001
FOR SEATS WITH PART NUMBER 2427
MODIFY IN ACCORDANCE WITH
VSB NO. 2427−25−001
OTHER SEATS
AFFECTED?
YES
NO
COMPLETE REPORTING SHEET
AND SEND IT TO AIRBUS
NOTE: THE PURPOSE OF FLOWCHARTS IS TO SUPPLEMENT THE INFORMATION
GIVEN IN THE PROCEDURE AND COMPLIANCE PARAGRAPHS AND NOT TO
SERVE AS THE PRIMARY SOURCE FOR TASKS OR COMPLIANCE TIMES
GIVEN IN THIS SERVICE BULLETIN.
N_SB_251BEK_6_FAAA_01_00
Figure A-GFAAA - Sheet 01
Flowchart
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 11
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
**CONF ALL
INSPECTION REPORT
SERVICE BULLETIN NUMBER: A320−25−1BEK
OPERATOR:
UPLOAD THIS INSPECTION REPORT
IN ACCORDANCE WITH ISI 00.00.00179
USING THE ONLINE REPORTING
APPLICATION IN AIRBUSWORLD
A/C MSN OR REGISTRATION:
FLIGHT CYCLES:
FLIGHT HOURS:
DATE OF INSPECTION:
SEAT MODEL:
QUANTITY:
2431
2428
2427
N_SB_251BEK_6_RAAA_01_01
Figure A-GRAAA - Sheet 01
Reporting Sheet
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 12
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
Appendix 01 - Affected Serial Numbers
**CONF ALL
AFFECTED PART NUMBERS
2427−41, −51, −61, −71, −72, −91
2428−81, −82
2431−81, −82
AFFECTED SERIAL/BATCH NO. PER MSN
MSN 6669
MSN 6672
MSN 6704
MSN 6736
MSN 6770
MSN 6773
1019−2428
1016−2428
1033−2428
1022−2428
1036−2428
1052−2428
1020−2428
1017−2428
1034−2428
1023−2428
1037−2428
1053−2428
1021−2428
1018−2428
1035−2428
1024−2428
1038−2428
23−2431
24−2427
31−2427
48−2427
27−2427
28−2427
32−2427
25−2427
29−2427
33−2427
26−2427
30−2427
34−2427
MSN 6787
MSN 6793
MSN 6804
MSN 6825
MSN 6835
MSN 6838
1056−2428
1043−2428
1045−2428
1050−2428
1074−2428
1084−2428
1057−2428
1044−2428
1046−2428
1051−2428
1075−2428
1085−2428
1063−2428
37−2427
1047−2428
44−2427
1076−2428
28−2431
50−2427
38−2427
41−2427
45−2427
63−2427
72−2427
39−2427
42−2427
46−2427
40−2427
43−2427
47−2427
MSN 6845
MSN 6848
MSN 6867
MSN 6889
MSN 6891
MSN 6897
1058−2428
1060−2428
1067−2428
1106−2428
1079−2428
1081−2428
1059−2428
1061−2428
1068−2428
1108−2428
1080−2428
1082−2428
51−2427
1064−2428
1069−2428
1109−2428
65−2427
1083−2428
52−2427
55−2427
59−2427
86−2427
66−2427
69−2427
53−2427
56−2427
60−2427
67−2427
70−2427
54−2427
57−2427
61−2427
68−2427
71−2427
MSN 6910
MSN 6926
MSN 6939
MSN 6947
MSN 6953
MSN 6976
1088−2428
1093−2428
1136−2428
1101−2428
1107−2428
1114−2428
1089−2428
1094−2428
1137−2428
1102−2428
1110−2428
1115−2428
1090−2428
78−2427
1138−2428
32−2431
35−2431
1116−2428
74−2427
79−2427
96−2427
75−2427
80−2427
88−2427
76−2427
81−2427
89−2427
87−2427
N_SB_251BEK_6_AAAA_01_02
Figure A-GAAAA - Sheet 01
Affected Serial Numbers
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 1
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
Service Bulletin REPORTING
TITLE:
EQUIPMENT/FURNISHINGS - CABIN ATTENDANT SEAT INSPECTION
OF THE BACKREST
MODIFICATION No.:
None
SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance and Flight
Operations Products if it is duly reported to Airbus.
General information
The SB Reporting policy is published in ISI 00.00.00135. This document provides information regarding:
the SB Reporting means and benefits, the update of customized Maintenance Products and customized
Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations Products" for
further information on the update of affected Flight Operations Products.
SB Reporting procedure
Standard practice to report SB is to use the online reporting application on AirbusWorld.
Refer to ISI 00.00.00179:
For complete information on reporting means to Airbus. Question 2 "What are the standard
practices for SB reporting?"
If this SB requires previous or simultaneous accomplishment of other SBs, Question 3 "What about
the reporting of prerequisite Service Bulletin?"
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting. It is revised on a
regular basis.
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 1
© AIRBUS S.A.S. 2007. All rights reserved.
@A318/A319/A320/A321
SERVICE BULLETIN
QUALITY PERCEPTION FORM
Use this form to tell us what is your perception of the quality of this Service Bulletin. The reported data
that you provide us will be used to analyse areas of difficulties and to take corrective action to further
improve the quality of our Service Bulletins.
We thank you for the time you have taken in completing this form.
(Please rate on a scale of 1 to 4, with 4 being the highest score)
- Quality rating of this SB
4
3
2
1
- Quality rating of the Accomplishment Instructions
4
3
2
1
- Quality rating of the Illustrations
4
3
2
1
- Is this SB easy to understand ?
Y/N
If you have had difficulties in the accomplishment of this SB please quote below the area(s) and give a
short description of the issue.
Planning
Material
Instructions
X Effectivity
X Kit content
X Preparation
X Reason
X List of Materials Operator Supplied
X Mod/Inspection
X Manpower
X Industry support
X Test
X References
X Re-identification
X Close-Up
X Publication
X Tooling
X Illustrations
Comments:
Operator:
Date:
Name/Title:
Please return this form to:
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE
Attn : SEM4 Service Bulletins Management
FAX : (33) 5 61 93 42 51
Or via your Resident Customer Support Office.
6
DATE: Nov 18/16
SERVICE BULLETIN No.: A320-25-1BEK
REVISION No.: 00 - Nov 18/16
Printed in FRANCE
Page: 1
© AIRBUS S.A.S. 2007. All rights reserved.