DREXELBROOK
®
DATA SHEET
DR7100 Series
Guided Radar (TDR) for
Distance, Level & Volume of Liquids, Slurries and Solids
Designed to Perform Better than any
Other TDR
Most Stable Measurement
Despite disturbances such as strongly agitated
surfaces, foam and coating of the probe or fine dust
in the tank, DR7100 will continue to measure where
other devices fail.
Measures any Product ...
Most 2-wire TDR devices measure down to
a dielectric of 1.5. As a result, many organic
compounds are not measured properly. The DR7100
measures down to 1.4 (and even 1.1 using superior
tank-bottom following mode).
... in any Application
5 different probes means there’s not an application
that we can’t handle.
The new DR7100 with its more advanced design
solutions has higher signal dynamics. Sharper
Pulses measure thinner interfaces. The superior
Time Base Stability allows better reproductibility,
which translates to better reliability.
Makes Level Gauging Easier than Ever
• Easy Navigation & Viewing
• Step 1 – The DR7100 tests itself to make sure its
electronics are working perfectly.
• Step 2 – The DR7100s Wizard walks you through a
simple series of questions to define your tank and
the product you want to measure.
• Step 3 – That’s all you need. Your DR7100 is already
measuring.
Choice of different Touch Screens:
(tank illustration, bargraph, oscilliscope...)
• 2-Wire
Class I Div1, Zone 0 Installation
• Special Process Separator for Extreme
Conditions
• Probe Types and Materials for all
Applications
Wizard Works Wonders
Setting up a 2-wire level gauge couldn’t be easier:
Simply fit the gauge to the tank, wire it up and
switch it on:
Interactive Help
Not certain what to do? You don’t need a handbook.
Simply wait 10 seconds, the help screen will appear
and tell you what to do.
www.Drexelbrook.com
DR7100 Series
Specifications
Input
Function
Time Domain Reflectometry (TDR)
Parameter
Level, distance, volume and / or interface
Max. measuring range Double rod 8mm / 0.3” 4m / 13ft
Single rod 8mm / 0.3” 4m / 13ft
Coaxial 22mm / 0.9” 6m / 20ft
Double cable 4mm / 0.15” 35m / 115ft
Single cable 4mm / 0.15” 35m / 115ft
Single cable 8mm / 0.3” 35m / 115ft
Output Signal
Output signal 1
4 - 20mA HART® or 3.8 - 20.5 mA
acc. to NAMUR NE 43
Output signal 2
4 - 20mA or 3.8 - 20.5 mA
(Optional)
acc. to NAMUR NE 43
Accuracy
0.05% (rel. 20 mA; 20°C / 68°F)
Resolution
±2 µA
Temperature Drift
Typically 50 ppm/K
Error Signal
High: 22 mA; Low: 3.6 mA
acc. to NAMUR NE 43
Max. Load
350 ohm
Measuring Accuracy - Reference conditions acc. to IEC770
Temperature
+20°C ±5°C / +68°F ±9°F
Pressure
1013 mbar abs. ±20 mbar
14.69 psig ±0.29 psig
Relative Humidity
60% ±15%
Resolution
1 mm / 0.04 “
Accuracy
In Direct Mode
Liquids
±3 mm / ±0.12”
when L < 10 m / 33 ft;
±0.03% of measured distance,
when L > 10 m / 33 ft
Powders
±20 mm / ±0.8”
Interface
±10 mm (εr Constant)
Application Conditions
Ambient Temp.
-40…+80°C / -40…+175°F;
EEx i: -40…+60°C / -40…+140°F
Storage Temp.
-40…+85°C / -40…+185°F
Flange Temp.
-40…+200°C / -40…+392°F
(Ex: refer to relevant device spec.)
Shock Resistance
100°C/min
Process Conditions
Operating Pressure
1…40 bar / -14.5…580 psig;
subject to process connection and temp.
Dielectric Constant
>
_ 1.4 Coaxial Probes >
_ 1.6
For single and Twin Probes
Vibration Resistance IEC 68-2-6 and prEN 50178
(10...57Hz: 0.075 mm / 57...150 Hz: 1 g)
Protection Category IP 66/67 equiv. to NEMA 6-6X
Human machine interface
Display
9 lines, 160x160 pixels in 8-step
greyscale with 4-button keypad
Operating Languages English, German, French, Italian,
Spanish, Portugese, Japanese,
Chinese (Mandarin), Russian
Mechanical Data
Housing
Wetted Parts
Rod
Aluminium
Stainless steel (1.4404 / 316L);
Hastelloy C-22 (2.4602)
Coaxial
Stainless steel (1.4404 / 316L);
Hastelloy C-22 (2.4602)
Cable (4mm /0.15") Stainless steel (1.4401 / 316);
Hastelloy C-22 (2.4602)
Process Fitting
Stainless steel (1.4404 / 316L);
Hastelloy C-22 (2.4602)
Gaskets
Viton (-40…+150°C / -40…+300°F);
Kalrez 6375 (-20…+150°C / -5 …+300°F)
Process Connection
Thread
G 3/4"...1 1/2"; NPT 3/4"...1 1/2"
Flange
DN 25…DN 150 (PN 40 / PN 16);
1”…8” (150 lb / 300 lb);
10 K (40…100A)
Electrical Connection - 2-Wire Power Supply
Terminals Output 1
Non-Ex/ EEx i 24 VDC (14 … 30 VDC)
EEx d 24 V DC (20 … 36 VDC)
Terminals Output 2
Non-Ex/ EEx i / EEx d
24 VDC (10 … 30 VDC)
Cable Entry Terminals M20x1.5; 1/2 NPT; G 1/2"
0.5…1.5 mm²
Approvals
ATEX
Ex ia
ATEX II 1 G D or II 1/2 G D or II 2 G D;
KEMA 04ATEXxxxxX
EEx ia IIC T3 … T6 T65°C … T90°C IP 6X
Ex d
ATEX II 1/2 G D or II 2 G D;
EEx d [ia] IIC T6 … T3 T65°C ... T90°C
IP 6X
FM
Ex ia
Intrinsically Safe (IS)
CSA
IS CL I, DIV 1, GR A,B,C,D
DIP CL II, III, DIV 1, GR E,F,G
NI ANI CL I, DIV 2, GR A,B,C,D (FM Only)
DIP CL II, III, DIV 1 GR E,F,G
Sensor Probe suitable for use in DIV 1 or ZONE 0
CL I, Zone 0, AEx ia IIC
CL I, Zone 2, GR IIC
CL I, Zone 0, Ex ia IIC
T6, Ta = 60° C
Ex d
Explosion Proof (XP)
XP CL I, DIV 1, GR A,B,C,D (FM Only)
CL I, DIV 2, GR A,B,C,D
DIP CL II, III, DIV 1, GR E,F,G
NI ANI CL I, DIV 2, GR A,B,C,D (FM Only)
DIP CL II, III, DIV 2 GR F,G
Sensor Probe suitable for use in DIV 1 or ZONE 0
CL I, Zone 0, AEx d ia IIC
CL I, Zone 2, GR IIC
CL I, Zone 0, Ex d ia IIC
T6, Ta = 60° C
Phone: +1 215-674-1234 • Fax: +1 215-674-2731
E-mail: drexelbrook.info@ametek.com
205 Keith Valley Road | Horsham PA 19044 U.S.A.
www.Drexelbrook.com
DR7100 Series
Model Numbering
DR7100
4
Approval
Approval
0 without
5 ATEX II G/D 1/2, 2 EEx d ia IIC T6 + WHG
1 WHG (overfill protection certificate)
6 FM / CSA IS Cl. I Div. 1 Gr. A-G
2 ATEX II G/D 1, 1/2, 2 EEx ia IIC T6
7 FM / CSA XP Cl. I Div. 1 Gr. A-G
3 ATEX II G/D 1/2, 2 EEx d ia IIC T6
8 FM / CSA General purpose
4 ATEX II G/D 1, 1/2, 2 EEx ia IIC T6 + WHG
Material Process Connection and Probe
0 316L / 1.4404
1 Hastelloy C-22 / 2.4602
(not for probes 4-5-D-E)
Probe
0
Single rod Ø 8 mm / 0.31 inch max. 4 m / 13.12 ft
1
Double rod Ø 8 mm / 0.31 inch max. 4 m / 13.12 ft
2
Coax Ø 22 mm / 0.87 inch max. 6 m / 19.69 ft
3
Single cable Ø 4 mm / 0.16 inch max. 35 m / 114.83 ft
4
Single cable Ø 8 mm / 0.31 inch max. 35 m / 114.83 ft
5
Double cable Ø 4 mm / 0.16 inch max. 35 m / 114.83 ft
A
NO probe - (Single rod Ø 8 mm / 0.31 inch max. 4 m / 13.12 ft )
B
NO probe - (Double rod Ø 8 mm / 0.31 inch max. 4 m / 13.12 ft)
C
NO probe - (Single cable Ø 4 mm / 0.16 inch max. 35 m / 114.83 ft)
D
NO probe - (Single cable Ø 8 mm / 0.31 inch max. 35 m / 114.83 ft)
E
NO probe - (Double cable Ø 4 mm / 0.16 inch max. 35 m / 114.83 ft)
Probe end type
0 without
1 Counterweight Ø 12 mm / 0.47 inch x 100 mm / 3.94 inch (Single cable Ø 8 mm / 0.31 inch)
2 Counterweight Ø 38 mm / 1.5 inch x 245 mm / 9.65 inch (Single cable Ø 8 mm / 0.31 inch)
3 Counterweight Ø 20 mm / 0.79 inch x 100 mm / 3.94 inch (Single cable Ø 4 mm / 0.16 inch)
4 Counterweight Ø 38 mm / 1.5 inch x 60 mm / 2.36 inch (Doble cable Ø 4 mm / 0.16 inch)
A turnbuckle
B chuck
C threaded end
D crimped end
E open end
Feedthrough/Temperature/Sealing
0 Standard / -40°C...+150°C / Viton GLT
1 Standard / -20°C...+150°C / Kalrez 6375
Process connection EN
Process connection EN
0 without
6 DN 50 PN 40 Form B1 EN1092
1 G 3/4 A ISO229
7 DN 80 PN 40 Form B1 EN1092
2 G 1 A ISO229
8 DN 100 PN 16 Form B1 EN1092
3 G 1 1/2 A ISO229
A DN 100 PN 40 Form B1 EN1092
4 DN 25 PN 40 Form B1 EN1093
B DN 150 PN 16 Form B1 EN1092
5 DN 40 PN 40 Form B1 EN1092
C DN 150 PN 40 Form B1 EN1092
Process connection ANSI
Process connection ANSI
0 without
8 2" 300 lb RF ANSI B16.5
1 3/4" NPT
A 3" 150 lb RF ANSI B16.5
2 1" NPT
B 3" 300 lb RF ANSI B16.5
3 1" 1/2 NPT
C 4" 150 lb RF ANSI B16.5
4 1" 150 lb RF ANSI B16.6
D 4" 300 lb RF ANSI B16.5
5 1" 1/2 150 lb RF ANSI B16.5
E 6" 150 lb RF ANSI B16.5
6 1" 1/2 300 lb RF ANSI B16.5
F 8" 150 lb RF ANSI B16.5
7 2" 150 lb RF ANSI B16.5
Process connection other
0 without
5 10K 40A RF JIS B2238
6 10K 50A RF JIS B2238
7 10K 80A RF JIS B2238
8 10K 100A RF JIS B2238
Output
0 Output: 4…20mA (HART)
1 1 Output: 4...20mA (HART) - INTERFACE
2 2 Outputs: 4...20mA (HART) + 4...20mA
3 2 Outputs: 4...20mA (HART) + 4...20mA - INTERFACE
Housing/Cable entry/Cable gland
0 Aluminium / M20x1,5 / without
1 Aluminium / 1/2 NPT / without
2 Aluminium / G 1/2 / without
3 Aluminium / M20x1,5 / Plastic (non-EEx: black, EEx i: blue)
4 Aluminium / M20x1,5 / Metall (only for EEx d devices)
Housing option
0 without
2 Weather protection
HMI (display and keys ... English is default second language for 2-3-4-5-6-7-8-A)
0 without
1 English (second language: German)
2 German
3 French
4 Italian
5 Spanish
6 Portugese
7 Japanese
8 Chinese (Mandarin)
A Russian
Version
1 Drexelbrook Standard
Dummy
0 without
Material certificate
0 without
1 3.1.B certificate: wetted parts
2 3.1.B certificate: parts under pressure
3 Positive Material Identification (PMI): wetted parts
4 Positive Material Identification (PMI): parts under pressure
5 2.1. material conformity certificate
Hydraulics control certificate
0 without
1 2.3. Hydraulics test certificate
2 3.1.B Hydraulics test certificate
Calibration certificate
0 without
1 Calibration certificate
Certificate (Miscellaneous)
0 without
1 2.1. Order conformity certificate
Drawing /TAG Number
0
1
2
3
DR7100
4
1
0
without
Drawing (overall dimensions)
Tag No. stainless steel plate
Drawing + TAG No. Stainless steel
Subject to Change Without Notice
Phone: +1 215-674-1234 • Fax: +1 215-674-2731
E-mail: drexelbrook.info@ametek.com
205 Keith Valley Road | Horsham PA 19044 U.S.A.
www.Drexelbrook.com
DR7100 Series
Dimensions - mm / Inch
182
7.2"
180
7.1"
122
4.8"
Thread
G 3/4"...1 1/2"
NPT 3/4"...1 1/2"
Flange
DN25...DN150
ANSI 1"...6"
99
3.9"
126.5
5"
289
11.4"
316.5
12.5"
190
7.5"
158.5
6.2"
Note:
Cable glands are not
delivered with the
device
Single Rod
Double Rod
Coaxial
8mm / 0.3"
8mm / 0.3"
22mm / 0.9"
L
L
L
Single Cable
4mm / 0.15"
8mm / 0.3"
Double Cable
4mm / 0.15"
L
L
Bottom
Measurement
Limit
L = Ordered Probe Length
Weights
Housing and Connection (316 SS)
[kg]
[lb]
3.3
7.3
Flange connection DN 25…80 / ANSI 1”…3”
4…7
8.8…15.4
Flange connection DN 100...150 / ANSI 4”…6”
7…12
15.4…26.5
Housing
Thread connection
3
6.6
[kg/m]
[lb/ft)
Single cable 4mm or 0.15”
0.12
0.08
Single cable 8mm or 0.3”
0.41
0.28
Double cable 4mm or 0.15”
0.24
0.16
Single rod 8mm or 0.3”
0.41
0.28
Double rod 8mm or 0.3”
0.82
0.56
Coaxial 22mm or 0.9”
0.79
0.53
Probes
Note:
Wide range of
counterweights and
anchoring solutions
available.
*
Only single cable 8mm / 0.3"
(solids application)
Phone: +1 215-674-1234 • Fax: +1 215-674-2731
E-mail: drexelbrook.info@ametek.com
205 Keith Valley Road | Horsham PA 19044 U.S.A.
www.Drexelbrook.com
DR7100 Series
Measurement Limits
Top
Dead Zone
εr = 80*
Bottom
Dead Zone
εr = 80*
Top
Dead Zone
εr = 2.3*
Bottom
Dead Zone
εr = 2.3*
Double Rod
125 mm / 4.9"
10 mm / 0.4"
165 mm / 6.5"
50 mm / 1.95"
Single Rod
200 mm / 7.9"
10 mm/ 0.4"
250 mm / 9.9"
50 mm / 1.95"
Coaxial
10 mm / 0.4"
10 mm / 0.4"
10 mm / 0.4"
50 mm / 1.95"
Double Cable
125 mm / 4.9"
10 mm / 0.4"
165 mm / 6.5"
50 mm / 1.95"
Single Cable 8 mm / 0.3”
200 mm / 7.9"
10 mm / 0.4"
250 mm / 9.9"
50 mm / 1.95"
Single Cable 4 mm / 0.15”
200 mm / 7.9"
10 mm / 0.4"
250 mm / 9.9"
50 mm / 1.95"
Probes
* 80 is εr of water; 2.3 is εr of oil
• A1 - Top dead zone
Minimum distance from flange to top limit of measuring range.
• A2 - Bottom dead zone
Length at end of probe, where measurement is not possible.
• D - non measurement zone
Zone where measurement cannot be taken.
Sin
4 m gle C
m abl
/0 e
.15
“
Sin
8 m gle C
m abl
/0 e
.3“
ub
8 m le C
/ 2 able
6’
Do
Co
ax
ial
d
Ro
gle
Sin
Ro
ub
le
Do
Probe Selection
d
• L - Probe length
Length specified by customer in the order.
Maximum Tank Height
4 m / 13 ft
6 m / 20 ft
35 m / 115 ft
Liquids
Liquid Application
LPG, LNG
Highly Viscous Liquids
Highly Crystallising Liquids
Highly Corrosive Liquids
Foam
Agitated Liquids
Spray in Tank
Storage Tanks
Bypass Chamber
Small Diameter Nozzles
Long Nozzles
Stilling Wells
Interface Measurement
Solids / Granulars
* with anchor fitting
Phone: +1 215-674-1234 • Fax: +1 215-674-2731
E-mail: drexelbrook.info@ametek.com
205 Keith Valley Road | Horsham PA 19044 U.S.A.
www.Drexelbrook.com
$2%8%,"2//+
Other
Great Solutions By: DREXELBROOK ®®
š
! ,EADER )N ,EVEL -EASUREMENT 3OLUTIONS
$2%8%,"2//+
š
5NIVERSAL
)))© 509-75
Series
3ERIES
Universal III™
,EVEL 4RANSMITTER
! ,EADER )N ,EVEL -EASUREMENT 3OLUTIONS
4HE 5NIVERSAL ))) SMART LEVEL
TRANSMITTER PROVIDES REMOTE CALIBRATION
WITHOUT HAVING TO EMPTY AND lLL THE
VESSEL
$- Series
3ERIES
DM330
#ONlGURATION 7ITHOUT
#HANGING ,EVEL
-AGNETOSTRICTIVE
#ONlGURE THE 5NIVERSAL ))) QUICKLY AND EASILY
BEFORE INSTALLATION OR ON THE VESSEL WITHOUT MOVING
THE LEVEL 3IMPLY KEY IN THE CALIBRATION DATA AND
WALK AWAY
,IQUID ,EVEL 3ENSOR
-AGNETOSTRICTIVE ,EVEL -E
3YSTEM TAKES lELD PROVEN
TECHNOLOGY AND INCORPORA
SAFETY WITH A lELD PROGRAM
AND SPAN 0ACKAGING IS O
LOW CLEARANCE DESIGN MA
$- IDEAL FOR LEVEL MON
VARIETY OF LIQUIDS AND TANK
2EMOTE #ONlGURATION
$2%8%,"2//+
š
!/NE
,EADER
)N ,EVEL -EASUREMENT
3OLUTIONS
4RANSMITTER
FOR !LL !PPLICATIONS
7ITH 2& !DMITTANCE TECHNOLOGY ONE TRANSMITTER
HANDLES ALL YOUR APPLICATIONS ,IQUIDS GRANULARS
SLURRIES INTERFACES CRYOGENIC TO Ž& FULL
VACUUM TO 03)
.O LONGER IS IT NECESSARY TO hSNIFFv FOR HAZARDOUS
GASSES OR TO GO OUT IN INCLEMENT WEATHER TO
CALIBRATE YOUR LEVEL TRANSMITTER #ONlGURE THE
5NIVERSAL ))) FROM THE CONVENIENCE AND COMFORT OF
THE CONTROL ROOM OR ANYWHERE ALONG THE TWO
WIRE LOOP
7IRELESS
)NTERFACE Solutions
3OLUTIONS
Wireless Interface
1UICK AND %ASY #ALIBRATION
0ROVEN
-AGNETOSTRICTIVE
5SE YOUR EXISTING (!24š
HANDHELD
3ENSING
COMMUNICATOR OR $REXELBROOKS
0# SOFTWARE TO
0ERFORMANCE
WITH &IELD
CONlGURE THE TRANSMITTER
0ROGRAMMABLE
4AMPER 0ROOF
3PAN
!METEK $REXELBROOK SIGNAL
CONDITIONING LINE UTILIZES
7IRELESS !NALOG $IGITAL ,INK
%ASIEST-OUNT
#ALIBRATION
%VER X 4RANSMITTER $). 2AIL 2ECEIVER 3ET
4UBE
.%-!
#ONlGURE THIS TRANSMITTER FROM ANYWHERE ALONG
THE TWO WIRE LOOP WITHOUT CHANGING THE LEVEL IN THE
VESSEL
$28
$28
4WO 6ARIATIONS 3ENSORS ARE A
33 OR mEXIBLE 06$& DESIGNS
STEEL VERSION HAS A CHOICE OF A M
OR AN OPTIONAL HOUSING WHICH INCL
CONNECTORS WITH ZERO AND SPAN A
OFFER TOTALLY WELDED CONSTRUCTION
.O ADJUSTMENTS
THE SPREAD
TRANSMITTER
PREVENTS
š
-(Z )3-ON
BAND
SPECTRUM
FREQUENCY
UNAUTHORIZED
hTWEAKINGv
OR INADVERTENT
CHANGES
HOPPING
TECHNOLOGY
TO GUARANTEE
A LICENSE
FREE
%ASY
)NSTALLATION
IN CALIBRATION
INTERFERENCE
FREE LINK BETWEEN REMOTE DEVICES AND
s CABLE
.O
CALIBRATION
NEEDED
THE CONTROL ROOM #OSTLY
AND CONDUIT
RUNS -EASUREMENT
ON
! ,EADER
)N ,EVEL
3OLUTIONS
4HE mEXIBLE 06$& VERSION OFF
5NSURPASSED !CCURACY
3MART !DVANTAGES
NEW PROJECTS OR RETROlTTING
OF EXISTINGZERO
SYSTEMS
ARE IN THE lELD
s
0ROGRAM
SPAN
.O
OTHER
2&
TRANSMITTER
MATCHES
THE
ACCURACY
OF
MOUNTING
OPTIONS AND PROVIDE
-AJOR ADVANTAGES OF THE 5NIVERSAL )))
ELIMINATED AND REPLACED WITH A MAINTENANCE FREE
s 3ET
UPPER
AND#OMMON
LOWER LIMITS ON BENCH PRIOR TO
STABILITYAND
ANDVERSATILE
REPEATABILITY
OF THE
5NIVERSAL
)))
s )GNORES #OATING "UILD 5P ON 3ENSING %LEMENT
RELIABLE
WIRELESS
SOLUTION
HIGH ACCURACY INVENTORY MONITORI
4HIS TRANSLATES
INTO SMOOTHER
OPERATION
LESS
INSTALLATION
APPLICATIONS
INCLUDE
-ONITORING
CONTROL OFAND
PRESSURE
s "UILT IN TANK STRAPPING
FEET
LEVEL
TEMPERATURE FLOW SWITCHING AND ALARMS
DOWNTIME
s #HOICE OF OUTPUT IN LEVEL mOW WEIGHT OR VOLUME
IN SITUATIONS WHERE CABLE
AND!CCURACY
CONDUIT ARE EITHER
(IGH
s &ACTORY PRECALIBRATION
#OMPATIBILITY
&UTURE&OR EXAMPLE
IMPOSSIBLE
OR TOO WITH
COSTLYTHE
TO INSTALL
!FFORDABLE
7IRE ,EVEL
4RANSM
!LL OF THE SENSORS
ELECTRONICS
s FULL SCALE OVER M! SPAN
4HE STANDARD
(!24READINGS
PROTOCOL
IS AACCURACY
PROVEN
s #HOICE OF DIGITAL OR M! TRANSMISSION
RETRIEVING
PRESSURE
FROM
A DEVICE ON THE
WITH
THE THE
PERFORMANCE
AND
FEATU
WITHIN
h
DIAMETER
SENSING
INSTRUMENTATION
PROTOCOL
/VER A HALF MILLION
OTHER
SIDE OF A RAILWAY
TRACK
s "UILT IN SELF DIAGNOSTICS
PREMIUM
LINE POWERED
SYSTEMS
-INIMAL
-AINTENANCE
BREAKTHROUGH
IN
PACKAGE
DESIGN
lELD INSTRUMENTS HAVE BEEN SUPPLIED BY OVER s AS
5NIQUE
DIAGNOSTIC
OUTPUT PROVIDES mOAT POSITION
4HE
MODULESMANUFACTURERS
ARE AVAILABLE
TRANSMITTER
RECEIVER
ELECTRONICS ENCLOSURE AT THE TOP O
INSTRUMENT
TOAPROCESS
PLANTS
ALL
INCH .OZZLE -OUNTING
BEYOND SET
SPAN BEYOND
ACTIVE RANGE AS WELL
PAIR AND COME FACTORY PROGRAMMED
CALIBRATED
AND
OVER THE WORLD 4HE 5NIVERSAL ))) IS ALSO COMPATIBLE
WHICH TRANSDUCER
REDUCES COST
AND
OFFERS
GR
TESTED AS A SET &URTHER SWITCH
CONlGURATION
AND
#OMPACT
DESIGN
ALLOWS
MOU
AS LOSSTHEIR
OF mOAT
WITH !LLEN "RADLEY
0,#S
THROUGH
3MART
PROGRAMMING
ARE NOT
REQUIRED
%ACH SET
IS GIVEN A
INSERTION
AND MOUNTING
ANY
INCH
NOZZLE
)T
ALSO
ALLOWS
FOR
A
REC
&EATURES
4RANSMITTER
)NTERFACE
PRODUCTS
UNIQUE
ADDRESS
AT THE FACTORY
ENABLING ,OW
MULTIPLE#LEARANCE
RADIO
0ATENTED
$ESIGN
NOZZLE MOUNTING ENABLING LEVEL TO BE REA
SYSTEMS TO WORK INDEPENDENTLY IN THE SAME AREA
s %LECTRONICS ALL WITHIN DIAMETER SENSOR ALLOWS VERY TOP
s 7IRELESS CONDUIT FOR ONE M! AND TWO DIGITAL
OF $-
THE VESSEL
4HE
IS A TWO WIRE LOOP
WITHOUT INTERFERENCE 4HE WEATHERPROOF TRANSMITTERS
SIGNALS
MOUNTING
OPTIONS
ARE AVAILABLE IN BOTH !# ANDWIDER
$# POWER
VERSIONS
THE AT LESS COST
INTRINSICALLY SAFE SENSOR WITH A CO
s 7EATHERPROOF .%-! X EQUIVALENT TO )0
RECEIVER IN $# ONLY SUITABLE FOR $). RAIL MOUNTING
!UTOMATIC
M! SPAN 4ANK 0ROlLING
HOUSING
0ATENTED
&LEXIBLE
6OLTAGE REQUIREMENT FOR
THE !# TRANSMITTER
IS 0ROBE
!UTO 0ROlLING© %LIMINATES INTERFERING S
TO 6!# 4HE $# s
POWERED
A COST EFFECTIVE HIGH
s 2ANGE TO MILES LINE OF SIGHT WITH /MNI
06$&MODULES
VERSION REQUIRE
PROVIDES
FROM AGITATORS AND OTHER INTERNAL VESSEL
TO 6$# POWER SOURCE
POWER SUPPLY
BATTERY
ANTENNA
! VARIETY
OF mOATS
ANDTOMOUNTIN
ACCURACY
INVENTORY
MONITORING UP TO FEET
OBSTRUCTIONS
WITHOUT
THE NEED
EMPTY
SOLAR ETC 1UICK AND EASY TO INSTALL THE PROCESS
s %ASY TO USE WIRE IN WIRE OUT NO SET UP OR
WITH mEXIBILITY AND REDUCED WEIGHT FOR EASIER
ARE
AVAILABLE
TO
lT
VIRTUALLY
AP
AND WITHOUT OPERATOR INTERVENTIONANY
%ASILY
SIGNALS ARE SIMPLY WIRED TO THE COLOR CODED WIRES
PROGRAMMING
INSTALLATION
OF THE TRANSMITTER AND OUTPUT
VIA WIRES CONNECTED
)NCLUDED
IS A SANITARY
ST
PIPES
AND OBSTRUCTIONS
THAT STAINLESS
ARE IN THE SO
s &REQUENCY (OPPING 3PREAD 3PECTRUM
TO THE RECEIVER .O WIRING IS REQUIRED IN BETWEEN
PATH
#ONTACT THE FACTORY TO MATCH YOU
TECHNOLOGY
3AFE
4YPICAL OUTDOOR RANGE IS)NTRINSICALLY
TO4WO
MILES
WITH NO
LINE OF
7IRE
,OOP
0OWERED (!24š
s ,ICENSE FREE -(Z )3- BAND
SIGHT TO MILES WITHsLINE&OF SIGHT
AND
METER
MILES
!4%8
#3!
#% ! !PPROVED
FT
2ANGE
5SER &RIENDLY
WITH PROFESSIONAL ANTENNA PROPAGATION STUDY AND
s WATT TRANSMIT POWER
)NTRINSIC 3AFETY AND %XPLOSION 0ROOF DESIGNS AND
3ET THE MEASUREMENT RANGE DIRECTLY IN IN
INSTALLATION
s -OUNTS ON v .04 CONDUIT
!PPROVALS PENDING
FEET MILLIMETERS CENTIMETERS OR METERS
4HE TRANSMITTERS MOUNT DIRECTLY TO v .04 CONDUIT
INTEGRAL DISPLAY WITH ENVIRONMENTALLY SEA
%ASY
SET UP
U.S.A.$ESCRIPTION
Sales: 800-553-9092 • 24-Hour Service:
800-527-6297
International
Support:
AND ARE
RATED .%-! X •
)0
AND MEASURE
MM 215-674-1234 • Fax: 215-674-2731
'ENERAL
KEYPAD 4HE DISPLAY IS MENU DRIVEN AND
6IA 0#
SOFTWARE
OR 4HE
(!24 #OMMUNICATOR
X MM OR v X v INCLUDING
/MNI
ANTENNA
BE CONlGURED WITHOUT DETAILED PROCEDUR
SPACE
EFlCIENT
$).
RAIL
MOUNTED
RECEIVER
TAKING
UP
-ENU DRIVEN CONlGURATION VIA INTEGRAL DISPLAY
4HE !METEK $REXELBROOK $28 AMETEK Nihon Drexelbrook
AMETEK Singapore Pte. Ltd.
AMETEK Precision Instruments
Europe
CRYPTIC CODES
NO PROBLEMS
ONLY MM LENGTH X MM HEIGHT X MM
$28 IS AN INTEGRATED RADIO )/ MODULE
2 Chome • 12-7 Minami Gyotoku
Kio Street 65
Rudolf-Diesel-Strasse 16
OR v X v X v10INAng
THEMo
CONTROL
CABINET
!UTOMATIC
4ANK
0ROlLING
DESIGNED TO ELIMINATE CABLE AND CONDUIT FOR Ichikawa
ONE City •WIDTH
Chiba 27201 Japan
#05-12 Techpoint • 569059 Singapore
D-40670 Meerbusch Germany
M!
CURRENT LOOP
AND5-07-100
TWO DIGITAL
SIGNALS
IN HARSH
DR7100-A
• EDO#
• Issue
#2 Phone:
,EVEL AND /PEN #HANNEL &LOW
!UTOMATICALLY
IGNORES MOST INTERNAL Phone:
OBSTRUCTIONS
81-473-56-6513
Phone:
65-6484-2388
49-2159-9136-0
Phone:
+1
215-674-1234
•
Fax:
+1
215-674-2731
INDUSTRIAL ENVIRONMENTS 4HIS UNIQUE ADDITION
TO
THE
.O
USER
ADJUSTMENTS
REQUIRED
Fax: 81-473-56-6535
Fax: 65-6481-6588
Fax: 49-2159-9136-39MEASUREMENTS
E-mail: nd@nihon-drexelbrook.co.jp
E-mail: aspl@ametek.com.sg
Web: www.ametek.de 4HE 53ONIC MAKES MEASUREMENTS ON LEV
205 Keith Valley Road
E-mail: &ULL
drexelbrook.info@ametek.com
4ANK -EASUREMENT
Horsham PA 19044 U.S.A.
DISTANCE VOLUME OR OPEN CHANNEL mOW E
4RANSDUCER CAN BE RECESSED IN A INCH )$ OR
E-mail - drexelbrook.info@ametek.com
CONlGURE 0RESET mUME AND WEIR CHARACT
205 Keith Valley Road | Horsham PA 19044 U.S.A.
©2005, by AMETEK, Inc. All rights reserved.
• PrintedTOin ALLOW
the U.S.A.
• EDO#TO
4-05-243
LARGER NOZZLE
LEVEL• DR7100-A
MEASUREMENTS
THE • Issue #1
Web - www.drexelbrook.com
ARE INCLUDED IN THE 53ONIC FOR OVER DI
VERY TOP OF THE VESSEL
mUMES AND WEIRS #USTOM CHARACTERIZATI
$2%8%,"2//+
USonic™ Series
53ONIC©
3ERIES
5LTRASONIC ,EVEL 4RANSMITTER
DREXELBROOK
www.Drexelbrook.com