GSM/EDGE BSS, Rel.
RG20(BSS), Operating
Documentation, Issue 07
BSS Radio Network Parameter Dictionary
DN9813866
Issue 28-6
Approval Date 2011-10-27
Confidential
BSS Radio Network Parameter Dictionary
The information in this document is subject to change without notice and describes only the
product defined in the introduction of this documentation. This documentation is intended for the
use of Nokia Siemens Networks customers only for the purposes of the agreement under which
the document is submitted, and no part of it may be used, reproduced, modified or transmitted
in any form or means without the prior written permission of Nokia Siemens Networks. The
documentation has been prepared to be used by professional and properly trained personnel,
and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes
customer comments as part of the process of continuous development and improvement of the
documentation.
The information or statements given in this documentation concerning the suitability, capacity,
or performance of the mentioned hardware or software products are given "as is" and all liability
arising in connection with such hardware or software products shall be defined conclusively and
finally in a separate agreement between Nokia Siemens Networks and the customer. However,
Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions
contained in the document are adequate and free of material errors and omissions. Nokia
Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which
may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO
EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED
TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY
OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION
IN IT.
This documentation and the product it describes are considered protected by copyrights and
other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark
of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective
owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2011. All rights reserved
f
Important Notice on Product Safety
This product may present safety risks due to laser, electricity, heat, and other sources
of danger.
Only trained and qualified personnel may install, operate, maintain or otherwise handle
this product and only after having carefully read the safety information applicable to this
product.
The safety information is provided in the Safety Information section in the “Legal, Safety
and Environmental Information” part of this document or documentation set.
The same text in German:
f
Wichtiger Hinweis zur Produktsicherheit
Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder
andere Gefahrenquellen ausgehen.
Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch
geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheitsanforderungen erfolgen.
Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal,
Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentationssatzes.
2
Id:0900d8058089b098
Confidential
DN9813866
Issue 28-6
BSS Radio Network Parameter Dictionary
Table of contents
This document has 1587 pages.
Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
DN9813866
1
Structure and conventions of BSS Radio Network Parameter Dictionary .
63
2
2.1
2.2
2.3
Autoconfiguration Pool (ACP) radio network object parameters . . . . . .
Circuit (CRCT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pool id (ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
pool size (SIZE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
3.18
3.19
3.20
3.21
3.22
3.23
3.24
3.25
3.26
3.27
3.28
3.29
3.30
3.31
3.32
3.33
3.34
3.35
Adjacent GSM Cell (ADJC/ADCE) radio network object parameters . . 69
adjacent cell identification (CI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
adjacent cell index (INDEX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
adjacent cell layer (ACL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Adjacent GPRS enabled (AGENA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
AMR target cell of direct access to desired layer (DADLA) . . . . . . . . . . 73
BCCH frequency (FREQ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
BTS colour code (BCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
C/I estimation weight (W1-W5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
cell identification of reference cell (CI1-CI5) . . . . . . . . . . . . . . . . . . . . . 78
cell type (CTY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
chained adj cell (CHAIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
directed retry threshold (DRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
DTM enabled (DTM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
DTM power budget margin (DPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
enable derived handover power (DHOPWR). . . . . . . . . . . . . . . . . . . . . 84
enable HO margin lev qual (MRGS) . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
fast moving threshold (FMT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
GPRS MS TX pwr max CCH (GTXP1) . . . . . . . . . . . . . . . . . . . . . . . . . 88
GPRS MS TX pwr max CCH 1x00 (GTXP2) . . . . . . . . . . . . . . . . . . . . . 89
GPRS penalty time (GPET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
GPRS rxlev Access min (GRXP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
GPRS temporary offset (GTEO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
HO margin delay time (HOMD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
HCS signal level threshold (HCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
HO level umbrella (AUCL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
HO load factor (OF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
HO margin lev (LMRG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
HO margin pbgt (PMRG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
HO margin qual (QMRG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
HO priority level (PRI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
HO target area (HOTA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
IBNACC state () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
level adjustment (L1-L5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
location area code (LAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
location area code of reference cell (LAC1-LAC5) . . . . . . . . . . . . . . . 108
Id:0900d8058089b098
Confidential
65
65
66
67
3
BSS Radio Network Parameter Dictionary
4
3.36
3.37
3.38
3.39
3.40
3.41
3.42
3.43
3.44
3.45
3.46
3.47
3.48
3.49
3.50
3.51
3.52
3.53
3.54
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
mobile country code of reference cell (MCC1-MCC5) . . . . . . . . . . . . . 110
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
mobile network code of reference cell (MNC1-MNC5) . . . . . . . . . . . . . 113
MS pwr opt level (POPT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
MS TX pwr max gsm (PMAX1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
MS TX pwr max gsm1x00 (PMAX2) . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
NCCR and DTM EGPRS PBGT margin (EPM) . . . . . . . . . . . . . . . . . . 117
NCCR and DTM GPRS PBGT margin (GPM) . . . . . . . . . . . . . . . . . . . 118
NCCR EGPRS quality margin (EQM) . . . . . . . . . . . . . . . . . . . . . . . . . . 119
NCCR GPRS quality margin (GQM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
network colour code (NCC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
priority class (PRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
reporting priority (REP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
routing area code (RAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
RX lev min cell (SL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
synchronised (SYNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
target cell of direct access to desired layer (DADL) . . . . . . . . . . . . . . . 128
TRHO target level (TRHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
Adjacent UTRAN Cell (UADJC/ADJW) radio network object parameters .
131
adjacent cell index (INDEX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
cell identification (CI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
cell parameter (CPA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
direct access Ec/Io threshold (DET) . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
downlink transmission diversity (DIV) . . . . . . . . . . . . . . . . . . . . . . . . . . 135
ISNCCR quality threshold (FQT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
location area code (LAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
minimum CPICH Ec/Io level (MET). . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
radio network controller identifier (RNC) . . . . . . . . . . . . . . . . . . . . . . . . 141
reporting priority (REP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
scrambling code (SCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
service area code (SAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
synchronisation case (SC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
WCDMA downlink carrier frequency (FREQ) . . . . . . . . . . . . . . . . . . . . 146
5
5.1
5.2
5.3
5.4
5.5
Authorised Network (ANE) radio network object parameters . . . . . . . . 148
authorised networks identification (ANE) . . . . . . . . . . . . . . . . . . . . . . . 148
authorised networks name (NAME) . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
network mobile country code (MCC1...6) . . . . . . . . . . . . . . . . . . . . . . . 150
network mobile network code (MNC1...6) . . . . . . . . . . . . . . . . . . . . . . . 151
network technology (TECH1...6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
6
6.1
6.2
Adjacent LTE Cell (ADJL) radio network object parameters. . . . . . . . . 154
barred LTE adjacent cell group (LTEBCG) . . . . . . . . . . . . . . . . . . . . . . 154
barred LTE adjacent cell list (LTEBCL). . . . . . . . . . . . . . . . . . . . . . . . . 155
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
DN9813866
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
barred LTE adjacent cell pattern (LTEBCP) . . . . . . . . . . . . . . . . . . . .
barred LTE adjacent cell pattern sense (LTEPS) . . . . . . . . . . . . . . . .
LTE cell downlink carrier frequency (FREQ) . . . . . . . . . . . . . . . . . . . .
LTE adjacent cell index (INDEX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTE adjacent cell mobile country code (MCC). . . . . . . . . . . . . . . . . . .
LTE cell min bandwidth (LTEMB) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTE adjacent cell min RX level (LTERXM) . . . . . . . . . . . . . . . . . . . . .
LTE adjacent cell mobile network code (MNC) . . . . . . . . . . . . . . . . . .
LTE adjacent cell priority (LTECP). . . . . . . . . . . . . . . . . . . . . . . . . . . .
LTE adjacent cell reselection lower threshold (LTERLT). . . . . . . . . . .
LTE adjacent cell reselection upper threshold (LTERUT) . . . . . . . . . .
tracking area code (TAC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7.1
7.2
7.3
BCCH Allocation Frequency List (BA/BAL) radio network object parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
frequency (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
identification of BCCH frequency list (-) . . . . . . . . . . . . . . . . . . . . . . . . 171
type of BCCH frequency list (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
8
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
8.20
8.21
8.22
8.23
8.24
8.25
8.26
8.27
8.28
Base Control Function (BCF) radio network object parameters . . . . .
Add BCF to chain / Remove BCF from chain (ADD / REM) . . . . . . . .
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
autoconfigure (AC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
automatic unlock allowed (AU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
abis interface connection type (AICT) . . . . . . . . . . . . . . . . . . . . . . . . .
attached CSDAP 1 (CSDAP1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
attached CSDAP 2 (CSDAP2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
attached CSDAP 3 (CSDAP3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
attached CSDAP 4 (CSDAP4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCCH TRX shutdown timer (BTIM) . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCF identification (BCF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS C/U-plane IP address (BCUIP) . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS IPv4 subnet mask length for C/U-plane (SMCUP). . . . . . . . . . . .
BTS IPv4 subnet mask length for M-plane (SMMP) . . . . . . . . . . . . . .
BTS M-plane IP address (BMIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
bit rate (BR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BSC-BSC interface failure (BSCBSC) . . . . . . . . . . . . . . . . . . . . . . . . .
BTS battery backup procedure (BBU) . . . . . . . . . . . . . . . . . . . . . . . . .
BTS site subtype (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCF HDLC ID list (BHIDL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCF up to date (BCFUTD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS C/U-plane IP address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS commissioning state (CSTAT) . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS M-plane IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS serial number () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BU1 abis throughput threshold (BU1) . . . . . . . . . . . . . . . . . . . . . . . . .
BU2 abis throughput threshold (BU2) . . . . . . . . . . . . . . . . . . . . . . . . .
clock source (CS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
156
157
158
160
161
162
163
164
165
166
167
169
174
174
175
177
178
179
182
183
184
185
186
188
189
190
192
193
194
195
197
199
200
202
203
205
206
207
208
210
211
5
BSS Radio Network Parameter Dictionary
8.29
8.30
8.31
8.32
8.33
8.34
8.35
8.36
8.37
8.38
8.39
8.40
8.41
8.42
8.43
8.44
8.45
8.46
8.47
8.48
8.49
8.50
8.51
8.52
8.53
8.54
8.55
8.56
8.57
8.58
8.59
8.60
8.61
8.62
8.63
8.64
8.65
8.66
8.67
8.68
8.69
8.70
8.71
8.72
8.73
8.74
8.75
6
D-channel link set name (DNAME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
D-channel link set number (DNBR). . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
DL committed information rate (DLCIR) . . . . . . . . . . . . . . . . . . . . . . . . 216
Downloaded SCF File Plan Id () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
external input number (INBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
external outputs ON / external outputs OFF (ON/OFF) . . . . . . . . . . . . 219
external synchronization source (ESS). . . . . . . . . . . . . . . . . . . . . . . . . 221
ethernet ring/path protection (ERPP) . . . . . . . . . . . . . . . . . . . . . . . . . . 222
ETP BCF ID (EBID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
FACCH LAPDm T200 (T200F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
Flexi EDGE Abis over IP Ethernet feature usage (TRS1). . . . . . . . . . . 226
Flexi EDGE TRS Abis Grooming feature usage (TRS3) . . . . . . . . . . . 227
Flexi EDGE TRS Loop Protection feature usage (TRS4) . . . . . . . . . . . 228
FlexiEDGE Additional 2 E1/T1 (TRS2) . . . . . . . . . . . . . . . . . . . . . . . . . 229
header compression for ML-PPP (HECOP) . . . . . . . . . . . . . . . . . . . . . 231
header compression for UDP IP (HECOU) . . . . . . . . . . . . . . . . . . . . . . 232
identification of test equipment (TEST). . . . . . . . . . . . . . . . . . . . . . . . . 233
IPSec enabled (IPSEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
master clock BCF identification (MCBCF) . . . . . . . . . . . . . . . . . . . . . . 236
master clock TRX (MCT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
maximum BTS multiplexing wait time (MBMWT) . . . . . . . . . . . . . . . . . 238
maximum ETP multiplexing wait time (MEMWT) . . . . . . . . . . . . . . . . . 239
maximum multiplexing packet size (MMPS) . . . . . . . . . . . . . . . . . . . . . 240
MCPA identity number (MCPAIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
MCPA identity port id (MCPAIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
MCPA identity position (MCPAIS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
MCPA power (MCPAPW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
MCPA power pooling bcf status (MCPABS) . . . . . . . . . . . . . . . . . . . . . 246
MCPA power pooling enabled (MCPAEN) . . . . . . . . . . . . . . . . . . . . . . 247
OMUSIG priority () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Packet Abis BCF Group ID (PABGID) . . . . . . . . . . . . . . . . . . . . . . . . . 250
PCM port ID 0 (PORT0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
PCM port ID 1 (PORT1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
PCM port ID 2 (PORT2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
PCM port ID 3 (PORT3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
PCM port ID 4 (PORT4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
PCM port ID 5 (PORT5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
PCM port ID 6 (PORT6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
PCM port ID 7 (PORT7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
polarity (POL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
packet abis congestion control (PACC) . . . . . . . . . . . . . . . . . . . . . . . . 262
Packet Abis over Satellite in use () . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
packet delay variation (PVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
packet loss on DL Abis PL1 threshold (PL1) . . . . . . . . . . . . . . . . . . . . 266
packet loss on DL Abis PL2 threshold (PL2) . . . . . . . . . . . . . . . . . . . . 268
packet TRS E1/T1 usage (TRS5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
QoS aware ethernet switch usage (QOSA) . . . . . . . . . . . . . . . . . . . . . 273
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
DN9813866
8.76
8.77
8.78
8.79
8.80
8.81
8.82
8.83
8.84
8.85
8.86
8.87
8.88
8.89
8.90
8.91
8.92
8.93
8.94
8.95
8.96
RF sharing state (RFSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
route (ROU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX difference limit (RXDL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SDCCH LAPDm T200 (T200S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
severity (SEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
site type (TYPE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
synch enabled (SENA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Synchronization Mode (SM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
system module HW (SMH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
text ID (TID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
text ID of the output 1...6 (OUT1-OUT6) . . . . . . . . . . . . . . . . . . . . . . .
TRX shutdown timer (NTIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX shutdown timer 2 (NTIM2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX shutdown timer 3 (NTIM3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL committed burst size (ULCBS) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL committed information rate (ULCIR). . . . . . . . . . . . . . . . . . . . . . . .
uplink traffic shaping (ULTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Used CS UDP MUX port () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Used PS UDP MUX port (). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vlan ID (VLANID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20W power licence usage (PLU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
274
275
276
278
279
280
283
284
286
287
288
289
292
293
295
297
298
300
301
302
304
9
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
9.10
9.11
9.12
9.13
9.14
9.15
9.16
9.17
9.18
9.19
9.20
9.21
9.22
9.23
9.24
9.25
Base Station Controller (BSC) radio network object parameters. . . . .
alarm limit for full rate TCH availability (ALFRT) . . . . . . . . . . . . . . . . .
alarm limit for half rate TCH availibility (ALHRT) . . . . . . . . . . . . . . . . .
alarm limit for SDCCH availability (ALSDC). . . . . . . . . . . . . . . . . . . . .
Alarm Threshold For Number Of Channel Seizure Requests (CSR). .
Alarm Threshold For Number Of Channel Seizures (CS) . . . . . . . . . .
Alarm Threshold For SDCCH Congestion (CNGS) . . . . . . . . . . . . . . .
Alarm Threshold For SDCCH Failure Rate (SCHFR) . . . . . . . . . . . . .
Alarm Threshold For TCH Congestion (CNGT) . . . . . . . . . . . . . . . . . .
Alarm Threshold For TCH Failure Rate (TCHFR) . . . . . . . . . . . . . . . .
alarm threshold for the share of high TCH interference (HIFSHR) . . .
AMH lower load threshold (ALT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMH Max Load Of Target Cell (AML) . . . . . . . . . . . . . . . . . . . . . . . . .
AMH upper load threshold (AUT). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMR Configuration In Handovers (ACH) . . . . . . . . . . . . . . . . . . . . . . .
AMR lower limit for FR resources (AHRL) . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Lower Threshold 1 (LDF1) . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Lower Threshold 2 (LDF2) . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Lower Threshold 3 (LDF3) . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Lower Threshold 4 (LDF4) . . . . . . . . . . . . . . . . . . .
AMR HR unpacking control (AHRUC) . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Upper Threshold 1 (UDF1) . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Upper Threshold 2 (UDF2) . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Upper Threshold 3 (UDF3) . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Upper Threshold 4 (UDF4) . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Lower Threshold 1 (LDH1) . . . . . . . . . . . . . . . . . . .
306
306
307
307
308
310
311
312
313
314
315
316
317
318
319
320
322
323
324
326
327
330
331
332
334
335
Id:0900d8058089b098
Confidential
7
BSS Radio Network Parameter Dictionary
9.26
9.27
9.28
9.29
9.30
9.31
9.32
9.33
9.34
9.35
9.36
9.37
9.38
9.39
9.40
9.41
9.42
9.43
9.44
9.45
9.46
9.47
9.48
9.49
9.50
9.51
9.52
9.53
9.54
9.55
9.56
9.57
9.58
9.59
9.60
9.61
9.62
9.63
9.64
9.65
9.66
9.67
9.68
9.69
9.70
9.71
9.72
8
AMR PPC DL HR Lower Threshold 2 (LDH2) . . . . . . . . . . . . . . . . . . . 336
AMR PPC DL HR Lower Threshold 3 (LDH3) . . . . . . . . . . . . . . . . . . . 338
AMR PPC DL HR Lower Threshold 4 (LDH4) . . . . . . . . . . . . . . . . . . . 339
AMR PPC DL HR Upper Threshold 1 (UDH1) . . . . . . . . . . . . . . . . . . . 340
AMR PPC DL HR Upper Threshold 2 (UDH2) . . . . . . . . . . . . . . . . . . . 342
AMR PPC DL HR Upper Threshold 3 (UDH3) . . . . . . . . . . . . . . . . . . . 343
AMR PPC DL HR Upper Threshold 4 (UDH4) . . . . . . . . . . . . . . . . . . . 344
AMR PPC UL FR Lower Threshold 1 (LUF1) . . . . . . . . . . . . . . . . . . . . 346
AMR PPC UL FR Lower Threshold 2 (LUF2) . . . . . . . . . . . . . . . . . . . . 347
AMR PPC UL FR Lower Threshold 3 (LUF3) . . . . . . . . . . . . . . . . . . . . 349
AMR PPC UL FR Lower Threshold 4 (LUF4) . . . . . . . . . . . . . . . . . . . . 350
AMR PPC UL FR Upper Threshold 1 (UUF1). . . . . . . . . . . . . . . . . . . . 351
AMR PPC UL FR Upper Threshold 2 (UUF2). . . . . . . . . . . . . . . . . . . . 353
AMR PPC UL FR Upper Threshold 3 (UUF3). . . . . . . . . . . . . . . . . . . . 354
AMR PPC UL FR Upper Threshold 4 (UUF4). . . . . . . . . . . . . . . . . . . . 355
AMR PPC UL HR Lower Threshold 1 (LUH1) . . . . . . . . . . . . . . . . . . . 357
AMR PPC UL HR Lower Threshold 2 (LUH2) . . . . . . . . . . . . . . . . . . . 358
AMR PPC UL HR Lower Threshold 3 (LUH3) . . . . . . . . . . . . . . . . . . . 359
AMR PPC UL HR Lower Threshold 4 (LUH4) . . . . . . . . . . . . . . . . . . . 361
AMR PPC UL HR Upper Threshold 1 (UUH1) . . . . . . . . . . . . . . . . . . . 362
AMR PPC UL HR Upper Threshold 2 (UUH2) . . . . . . . . . . . . . . . . . . . 363
AMR PPC UL HR Upper Threshold 3 (UUH3) . . . . . . . . . . . . . . . . . . . 365
AMR PPC UL HR Upper Threshold 4 (UUH4) . . . . . . . . . . . . . . . . . . . 366
AMR set grades enabled (ASG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
AMR upper limit for FR resources (AHRU) . . . . . . . . . . . . . . . . . . . . . . 368
A-If AF1 WFQ weight (AAF1WF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
A-If AF2 WFQ weight (AAF2WF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
A-If AF3 WFQ weight (AAF3WF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
A-if AF4 WFQ weight (AAF4WF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
A-If BE WFQ weight (ABEWFQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
A-IF CS U-PLANE DSCP PHB TC IN BSS (ADSCPB) . . . . . . . . . . . . 376
A-IF CS U-PLANE DSCP PHB TC IN MGW (ADSCPM) . . . . . . . . . . . 377
abis C-plane to DSCP mapping (ACP) . . . . . . . . . . . . . . . . . . . . . . . . . 379
abis M-plane to DSCP mapping (AMP) . . . . . . . . . . . . . . . . . . . . . . . . 380
abis U-plane CS to DSCP mapping (AUCS). . . . . . . . . . . . . . . . . . . . . 382
abis U-plane PS to DSCP mapping (AUPS) . . . . . . . . . . . . . . . . . . . . . 383
Background traffic class scheduling weight for ARP 1 (BGSW1) . . . . 385
Background traffic class scheduling weight for ARP 2 (BGSW2) . . . . 386
Background traffic class scheduling weight for ARP 3 (BGSW3) . . . . 387
BCSU load threshold (BCSUL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
BIM confidence probability (BCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
BIM interference threshold (BIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
BIM update guard time (BUGT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
bim update period (BUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
BIM update scaling factor (BUSF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
BTS site battery backup forced HO timer (TIM) . . . . . . . . . . . . . . . . . . 395
backhaul timer duration start reaction (BTON) . . . . . . . . . . . . . . . . . . . 396
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.73
9.74
9.75
9.76
9.77
9.78
9.79
9.80
9.81
9.82
9.83
9.84
9.85
9.86
9.87
9.88
9.89
9.90
9.91
9.92
9.93
9.94
9.95
9.96
9.97
9.98
9.99
9.100
9.101
9.102
9.103
9.104
9.105
9.106
9.107
9.108
9.109
9.110
9.111
9.112
9.113
9.114
9.115
9.116
9.117
9.118
9.119
DN9813866
backhaul timer duration stop reaction (BTOFF). . . . . . . . . . . . . . . . . .
C/I Target 14.4 (CIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I target AMR FR (CIAF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I target AMR HR (CIAH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I Target FR (CIF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I Target GPRS (CIGP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I target HR (CIH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I target OSC DFR (CIDFR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I target OSC DHR (CIDHR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I Target SDCCH (CISD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I target UL offset (CIUL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CN identity (CNID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS load balancing value (LOAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS MSC State (STATE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS NAS node method (NASMETHOD) . . . . . . . . . . . . . . . . . . . . . . . .
CS NRI length (LENGTH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS NRI list (-). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS TCH allocation calculation (CTC). . . . . . . . . . . . . . . . . . . . . . . . . .
CS TCH allocation RTSL0 (CTR) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS Weight Factor (WEIGHT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C-plane packet drop period (CPLPDP) . . . . . . . . . . . . . . . . . . . . . . . .
CS packet drop period (CSPDP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS UDP-MUX port (CSUMP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
clock-sync to DSCP Mapping (CLKS) . . . . . . . . . . . . . . . . . . . . . . . . .
DCS macrocell threshold (DMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS microcell threshold (DMIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
default SPC (DEF_SPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
delay of HO and PC for emergency calls (DEC) . . . . . . . . . . . . . . . . .
DFCA channel allocation method (DCAM) . . . . . . . . . . . . . . . . . . . . .
disable external DR (DEXDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
disable internal HO (DINHO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL PC 8PSK BEP target (PCPSK) . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL PC C/I target (PCCI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL high priority SSS (DHP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL low priority SSS (DLP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL normal priority SSS (DNP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DLDC offset for PCU2-E Selection (DOP) . . . . . . . . . . . . . . . . . . . . .
DTM fragmentation penalty (DFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTRX power down supervision period (PWDPRD) . . . . . . . . . . . . . . .
EGPRS inactivity criteria (EGIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
enable answer to paging call on FACCH (EPF). . . . . . . . . . . . . . . . . .
enable call re-establishment on FACCH (ERF) . . . . . . . . . . . . . . . . . .
enable emergency call on FACCH (EEF) . . . . . . . . . . . . . . . . . . . . . .
enable ordinary calls on FACCH (EOF). . . . . . . . . . . . . . . . . . . . . . . .
ending moment for supervision of BTS (EMBNT) . . . . . . . . . . . . . . . .
ending moment for supervision of BTS (EMBNT) . . . . . . . . . . . . . . . .
events per hour for EGPRS inactivity alarm (IEPH). . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
398
399
400
401
402
403
405
406
407
408
409
410
411
412
413
414
416
419
421
422
423
424
426
427
429
430
431
432
433
435
436
437
438
439
440
441
442
443
445
446
448
449
450
451
452
453
454
9
BSS Radio Network Parameter Dictionary
9.120
9.121
9.122
9.123
9.124
9.125
9.126
9.127
9.128
9.129
9.130
9.131
9.132
9.133
9.134
9.135
9.136
9.137
9.138
9.139
9.140
9.141
9.142
9.143
9.144
9.145
9.146
9.147
9.148
9.149
9.150
9.151
9.152
9.153
9.154
9.155
9.156
9.157
9.158
9.159
9.160
9.161
9.162
9.163
10
Expected BSC-BSC interface delay (EBID) . . . . . . . . . . . . . . . . . . . . . 455
FEP in PC HO use (FPHO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
Forced Mode (FCDMODE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
forced release priority threshold (FRPT) . . . . . . . . . . . . . . . . . . . . . . . . 458
free TSL for CS downgrade (CSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460
Free TSLs For CS Upgrade (CSU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
GPRS territory update guard time (GTUGT). . . . . . . . . . . . . . . . . . . . . 462
GSM Macrocell Threshold (GMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
GSM Microcell Threshold (GMIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
HO preference order interference DL (HDL). . . . . . . . . . . . . . . . . . . . . 465
HO preference order interference UL (HUL). . . . . . . . . . . . . . . . . . . . . 466
IMSI based handover gsm cells anonymous ms (IBGA) . . . . . . . . . . . 467
IMSI based handover WCDMA cells anonymous ms (IBWA). . . . . . . . 468
initial AMR channel rate (IAC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
Initial AMR codec type (IACT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
internal handover to external (IHTA). . . . . . . . . . . . . . . . . . . . . . . . . . . 472
intra segment SDCCH HO guard (ISS). . . . . . . . . . . . . . . . . . . . . . . . . 473
ISHO preferred for non-DTM MS (IPND) . . . . . . . . . . . . . . . . . . . . . . . 474
IBNACC enabled () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
LAPD load threshold (LAPDL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
load rate for channel search (CLR). . . . . . . . . . . . . . . . . . . . . . . . . . . . 478
local switching enabled for intercepted calls (LSEIC) . . . . . . . . . . . . . . 479
lower limit for FR TCH resources (HRL) . . . . . . . . . . . . . . . . . . . . . . . . 480
maximum mean holding time for SDCCHs (MAXHTS) . . . . . . . . . . . . . 482
maximum mean holding time for TCHs (MAXHTT) . . . . . . . . . . . . . . . 483
maximum number of DL TBF (MNDL) . . . . . . . . . . . . . . . . . . . . . . . . . 484
maximum number of UL TBF (MNUL) . . . . . . . . . . . . . . . . . . . . . . . . . 485
maximum TCH transaction rate (MTTR) . . . . . . . . . . . . . . . . . . . . . . . . 486
mean BEP limit MS multislot pwr prof 0 with 2 UL TSL (BL02) . . . . . . 487
mean BEP limit MS multislot pwr prof 0 with 3 UL TSL (BL03) . . . . . . 488
mean BEP limit MS multislot pwr prof 0 with 4 UL TSL (BL04) . . . . . . 489
mean BEP limit MS multislot pwr prof 1 with 2 UL TSL (BL12) . . . . . . 490
mean BEP limit MS multislot pwr prof 1 with 3 UL TSL (BL13) . . . . . . 491
mean BEP limit MS multislot pwr prof 1 with 4 UL TSL (BL14) . . . . . . 492
mean BEP limit MS multislot pwr prof 2 with 3 UL TSL (BL23) . . . . . . 493
mean BEP limit MS multislot pwr prof 2 with 4 UL TSL (BL24) . . . . . . 495
measurement period for high TCH interference supervision (PRDHIF) 496
measurement period for SDCCH mean holding time supervision (PRDMHS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
measurement period for supervision of BTS with no transactions
(PRDBNT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498
measurement period for supervision of channel failure rate (PRDCFR). . .
499
measurement period for supervision of congestion in BTS (PRDCNG) 500
measurement period for TCH mean holding time supervision (PRDMHT) .
501
minimum mean holding time for TCHs (MINHTT). . . . . . . . . . . . . . . . . 502
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.164
9.165
9.166
9.167
9.168
9.169
9.170
9.171
9.172
9.173
9.174
9.175
9.176
9.177
9.178
9.179
9.180
9.181
9.182
9.183
9.184
9.185
9.186
9.187
9.188
9.189
9.190
9.191
9.192
9.193
9.194
9.195
9.196
9.197
9.198
9.199
9.200
9.201
9.202
9.203
9.204
9.205
9.206
9.207
9.208
9.209
9.210
DN9813866
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MS distance behaviour (DISB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M-plane packet drop period (MPLPDP) . . . . . . . . . . . . . . . . . . . . . . . .
MC-PPP assured forwarding class 1 (MCAFC1) . . . . . . . . . . . . . . . . .
MC-PPP assured forwarding class 2 (MCAFC2) . . . . . . . . . . . . . . . . .
MC-PPP assured forwarding class 3 (MCAFC3) . . . . . . . . . . . . . . . . .
MC-PPP assured forwarding class 4 (MCAFC4) . . . . . . . . . . . . . . . . .
MC-PPP best effort (MCBE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MC-PPP Expedited Forwarding (MCEF) . . . . . . . . . . . . . . . . . . . . . . .
NACC enabled (NACC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nbr measurement period in NC2 (NMPN) . . . . . . . . . . . . . . . . . . . . . .
NCCR control mode (NCM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NCCR idle mode reporting period (NIRP) . . . . . . . . . . . . . . . . . . . . . .
NCCR neighbor cell penalty (NNCP) . . . . . . . . . . . . . . . . . . . . . . . . . .
NCCR return to old cell time (NOCT). . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
504
505
507
508
510
511
512
514
515
516
518
519
520
522
523
524
526
527
528
530
532
534
536
538
540
541
543
544
546
547
549
550
552
553
555
556
557
558
560
561
562
563
564
565
566
568
569
11
BSS Radio Network Parameter Dictionary
9.211
9.212
9.213
9.214
9.215
9.216
9.217
9.218
9.219
9.220
9.221
9.222
9.223
9.224
9.225
9.226
9.227
9.228
9.229
9.230
9.231
9.232
9.233
9.234
9.235
9.236
9.237
9.238
9.239
9.240
9.241
9.242
9.243
9.244
9.245
9.246
9.247
9.248
9.249
9.250
9.251
9.252
9.253
9.254
9.255
9.256
9.257
12
NCCR target cell penalty time (NTPT) . . . . . . . . . . . . . . . . . . . . . . . . . 570
NCCR transfer mode reporting period (NTRP) . . . . . . . . . . . . . . . . . . . 571
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 580
NRI (NRI list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581
Null NRI (NULLNRI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582
number of ignored transcoder failures (ITCF). . . . . . . . . . . . . . . . . . . . 584
number of preferred cells (NPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584
penalty trigger measurement period (PTMP) . . . . . . . . . . . . . . . . . . . . 586
PFC ack BLER limit for transfer delay 1 (ABL1) . . . . . . . . . . . . . . . . . 587
PFC unack BLER limit for SDU error ratio 1 (UBL1). . . . . . . . . . . . . . 588
pre-emption usage in handover (PRE) . . . . . . . . . . . . . . . . . . . . . . . . . 589
precise paging enabled for repagings (PRECRP) . . . . . . . . . . . . . . . . 590
precise paging expanding delay (PRECPD) . . . . . . . . . . . . . . . . . . . . . 591
precise paging MSC repaging delay (PRECMD) . . . . . . . . . . . . . . . . . 592
precise paging location records living time (PRECPL) . . . . . . . . . . . . . 593
precise paging TMSI optimization (PRECTO) . . . . . . . . . . . . . . . . . . . 594
priority level (PR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595
PSE overload alarm threshold (POAT) . . . . . . . . . . . . . . . . . . . . . . . . . 595
PSE PCU selection algorithm threshold (PSAT). . . . . . . . . . . . . . . . . . 596
public served count (PSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 597
packet loss timer duration start reaction (PLTON) . . . . . . . . . . . . . . . . 598
packet loss timer duration stop reaction (PLTOFF) . . . . . . . . . . . . . . . 600
PS packet drop period (PSPDP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601
PS UDP-MUX port (PSUMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602
QC NCCR action trigger threshold (QCATN) . . . . . . . . . . . . . . . . . . . 604
QC reallocation action trigger threshold (QCATR). . . . . . . . . . . . . . . . 605
RNC to SPC mapping info (RNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 606
RNC ID (RNCID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607
RNW configuration Identification (RNW ID) . . . . . . . . . . . . . . . . . . . . . 608
RNW fallback configuration identification (FB ID) . . . . . . . . . . . . . . . . . 609
RNW plan configuration identification (PLAN ID) . . . . . . . . . . . . . . . . . 610
RNW plan database state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611
RX antenna supervision period (RXANT) . . . . . . . . . . . . . . . . . . . . . . . 613
RX level balance (RXBAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614
RX level based TCH access (RXTA) . . . . . . . . . . . . . . . . . . . . . . . . . . 615
RX quality limit MS multislot pwr prof 0 with 2 UL TSL (RL02) . . . . . . . 616
RX quality limit MS multislot pwr prof 0 with 3 UL TSL (RL03) . . . . . . . 617
RX quality limit MS multislot pwr prof 0 with 4 UL TSL (RL04) . . . . . . . 618
RX quality limit MS multislot pwr prof 1 with 2 UL TSL (RL12) . . . . . . . 619
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.258
9.259
9.260
9.261
9.262
9.263
9.264
9.265
9.266
9.267
9.268
9.269
9.270
9.271
9.272
9.273
9.274
9.275
9.276
9.277
9.278
9.279
9.280
9.281
9.282
9.283
9.284
9.285
9.286
9.287
9.288
9.289
9.290
9.291
9.292
9.293
9.294
9.295
9.296
9.297
9.298
9.299
9.300
9.301
9.302
9.303
9.304
DN9813866
RX quality limit MS multislot pwr prof 1 with 3 UL TSL (RL13) . . . . . .
RX quality limit MS multislot pwr prof 1 with 4 UL TSL (RL14) . . . . . .
RX quality limit MS multislot pwr prof 2 with 3 UL TSL (RL23) . . . . . .
RX quality limit MS multislot pwr prof 2 with 4 UL TSL (RL24) . . . . . .
SACCH repeat window (SRW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAIC DL C/I offset (SCIO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
service area penalty time (SAPT) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
signalling point code (SPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
signaling point code (SPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
signaling point code (SPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
slow AMR LA enabled (SAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/I 14.4 (SBCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Blocking C/I AMR FR (SBAF). . . . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/I AMR HR (SBAH) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/I FR (SBF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/I GPRS (SBGP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Blocking C/I HR (SBH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/I OSC DFR (SBDFR) . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/I OSC DHR (SBDHR). . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/I SDCCH (SBSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/N 14.4 (SBCN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/N AMR FR (SBCNAF) . . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/N AMR HR (SBCNAH) . . . . . . . . . . . . . . . . . . . . . . . .
soft blocking C/N FR (SBCNF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Blocking C/N HR (SBCNH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
starting moment for supervision of BTS (SMBNT). . . . . . . . . . . . . . . .
starting moment for supervision of BTS (SMBNT). . . . . . . . . . . . . . . .
subscriber type (ST). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
supervision period length for EGPRS inactivity alarm (SPL) . . . . . . . .
SSM enabled (SSME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
site support traffic to DSCP mapping (SS). . . . . . . . . . . . . . . . . . . . . .
TCH in handover (HRI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCH transaction count (TTRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
threshold for high TCH interference level (HIFLVL). . . . . . . . . . . . . . .
time limit WPS (TLW). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
time limit WPS handover (TLWH) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRHO guard time (TGT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
triggering threshold for service area penalty (TTSAP). . . . . . . . . . . . .
TS AF1 WFQ weight (AF1WFQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS AF2 WFQ weight (AF2WFQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS AF3 WFQ weight (AF3WFQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS AF4 WFQ weight (AF4WFQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS BE WFQ weight (BEWFQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL priority 1 SSS (UP1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL priority 2 SSS (UP2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL priority 3 SSS (UP3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL priority 4 SSS (UP4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
621
622
623
624
625
626
629
630
631
632
633
634
635
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
655
656
658
659
660
661
662
663
664
666
667
668
670
671
672
673
674
13
BSS Radio Network Parameter Dictionary
14
9.305
9.306
9.307
9.308
9.309
9.310
9.311
9.312
9.313
9.314
9.315
9.316
9.317
9.318
upper limit for FR TCH resources (HRU) . . . . . . . . . . . . . . . . . . . . . . . 675
upper limit of MS speed class 1 (MSSCF) . . . . . . . . . . . . . . . . . . . . . . 676
upper limit of MS speed class 2 (MSSCS) . . . . . . . . . . . . . . . . . . . . . . 677
variable DL step size (VDLS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 678
VLAN priority AF1 (VPAF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 679
VLAN priority AF2 (VPAF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680
VLAN priority AF3 (VPAF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682
VLAN priority AF4 (VPAF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683
VLAN priority BE (VPBE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684
VLAN priority EF (VPEF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686
WCDMA FDD NCCR enabled (WFNE) . . . . . . . . . . . . . . . . . . . . . . . . 687
WCDMA FDD NCCR preferred (WFNP). . . . . . . . . . . . . . . . . . . . . . . . 688
WPS preference capacity (WPEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690
WPS priority capacity (WPIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691
10
10.1
10.2
10.3
10.4
10.5
10.6
10.7
10.8
10.9
10.10
10.11
10.12
10.13
10.14
10.15
10.16
10.17
10.18
10.19
10.20
10.21
10.22
10.23
10.24
10.25
10.26
10.27
10.28
10.29
10.30
10.31
10.32
Base Transceiver Station (BTS) radio network object parameters . . . . 693
adaptive LA algorithm (ALA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694
AMR FR codec mode set (FRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695
AMR FR DL threshold 1 (FRTD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696
AMR FR DL threshold 2 (FRTD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698
AMR FR DL threshold 3 (FRTD3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700
AMR FR hysteresis 1 (FRH1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702
AMR FR hysteresis 2 (FRH2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 704
AMR FR hysteresis 3 (FRH3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706
AMR FR initial codec mode indicator (ICMI and FRI) . . . . . . . . . . . . . . 709
AMR FR start mode (FRS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
AMR FR UL threshold 1 (FRTU1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712
AMR FR UL threshold 2 (FRTU2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 714
AMR FR UL threshold 3 (FRTU3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716
AMR HR codec mode set (HRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 718
AMR HR DL threshold 1 (HRTD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 719
AMR HR DL threshold 2 (HRTD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720
AMR HR DL threshold 3 (HRTD3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
AMR HR hysteresis 1 (HRH1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724
AMR HR hysteresis 2 (HRH2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727
AMR HR hysteresis 3 (HRH3 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 729
AMR HR initial codec mode indicator (ICMI and HRI) . . . . . . . . . . . . . 732
AMR HR start mode (HRS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733
AMR HR UL radio link timeout increase step (AHURIS). . . . . . . . . . . . 735
AMR HR UL threshold 1 (HRTU1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 736
AMR HR UL threshold 2 (HRTU2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
AMR HR UL threshold 3 (HRTU3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
AMR UL radio link timeout increase step (AURIS) . . . . . . . . . . . . . . . . 742
AMR-WB codec mode set (ACMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743
AMR-WB FR threshold 1 (AFRT1). . . . . . . . . . . . . . . . . . . . . . . . . . . . 744
AMR-WB FR threshold 2 (AFRT2). . . . . . . . . . . . . . . . . . . . . . . . . . . . 745
AMR-WB FR hysteresis 1 (AFRH1) . . . . . . . . . . . . . . . . . . . . . . . . . . . 747
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
10.33
10.34
10.35
10.36
10.37
10.38
10.39
10.40
10.41
10.42
10.43
10.44
10.45
10.46
10.47
10.48
10.49
10.50
10.51
10.52
10.53
10.54
10.55
10.56
10.57
10.58
10.59
10.60
10.61
10.62
10.63
10.64
10.65
10.66
10.67
10.68
10.69
10.70
10.71
10.72
10.73
10.74
10.75
10.76
10.77
10.78
10.79
DN9813866
AMR-WB FR hysteresis 2 (AFRH2). . . . . . . . . . . . . . . . . . . . . . . . . . .
antenna hopping (AHOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCCH TRX power (BCCHTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
boundary 0 (BO0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
boundary 1 (BO1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
boundary 2 (BO2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
boundary 3 (BO3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
boundary 4 (BO4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
boundary 5 (BO5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BSC-BSC Interface Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS downlink throughput factor for CS1-CS4 (TFD) . . . . . . . . . . . . . .
BTS downlink throughput factor for MCS1-MCS9 (TFDM) . . . . . . . . .
BTS hopping mode (HOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS identification (BTS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS load in SEG (LSEG). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS name (NAME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS TCH Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS uplink throughput factor for CS1-CS4 (TFU) . . . . . . . . . . . . . . . .
BTS uplink throughput factor for MCS1-MCS4 (TFUM1). . . . . . . . . . .
BTS uplink throughput factor for MCS1-MCS9 (TFUM). . . . . . . . . . . .
BCSU index (BCSU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/N threshold (CNT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
composited multi site cell (CMSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
cell number in BTS HW (CHW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
coding schemes CS3 and CS4 enabled (CS34) . . . . . . . . . . . . . . . . .
dedicated GPRS capacity (CDED) . . . . . . . . . . . . . . . . . . . . . . . . . . .
default GPRS capacity (CDEF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DFCA mobile allocation frequency lists (DMAL) . . . . . . . . . . . . . . . . .
DFCA mode (DMOD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DFCA unsynchronized mode MA frequency list (DUMAL) . . . . . . . . .
DL coding scheme in acknowledged mode (DCSA) . . . . . . . . . . . . . .
DL coding scheme in ext area acknowledged mode (DCSEA) . . . . . .
DL coding scheme In ext area unacknowledged mode (DCSEU) . . . .
DL coding scheme in unacknowledged mode (DCSU) . . . . . . . . . . . .
DL noise level (DLN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DLDC enabled (DCENA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EGPRS enabled (EGENA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EGPRS inactivity alarm end time (EAE) . . . . . . . . . . . . . . . . . . . . . . .
EGPRS inactivity alarm end time (EAE) . . . . . . . . . . . . . . . . . . . . . . .
EGPRS inactivity alarm start time (EAS) . . . . . . . . . . . . . . . . . . . . . . .
EGPRS inactivity alarm start time (EAS) . . . . . . . . . . . . . . . . . . . . . . .
EGPRS inactivity alarm weekdays (EAW) . . . . . . . . . . . . . . . . . . . . . .
extended cell for GPRS/EDGE enabled (EXGENA) . . . . . . . . . . . . . .
extended cell location keep period (EXKEEP). . . . . . . . . . . . . . . . . . .
extended paging enabled (EXTPG) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fast Return to TD-SCDMA (FRTDD). . . . . . . . . . . . . . . . . . . . . . . . . .
forced AMR HR mode C/I threshold (FAHT) . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
748
750
751
752
753
754
755
756
757
758
759
760
761
763
764
765
766
767
768
769
770
771
772
773
775
776
777
779
780
781
782
784
786
787
789
790
791
792
793
794
795
796
798
800
801
802
804
15
BSS Radio Network Parameter Dictionary
10.80
10.81
10.82
10.83
10.84
10.85
10.86
10.87
10.88
10.89
10.90
10.91
10.92
10.93
10.94
10.95
10.96
10.97
10.98
10.99
10.100
10.101
10.102
10.103
10.104
10.105
10.106
10.107
10.108
10.109
10.110
10.111
10.112
10.113
10.114
10.115
10.116
10.117
10.118
10.119
10.120
10.121
10.122
10.123
10.124
10.125
10.126
16
forced HR mode C/I averaging period (FHR) . . . . . . . . . . . . . . . . . . . . 805
forced HR mode C/I threshold (FHT) . . . . . . . . . . . . . . . . . . . . . . . . . . 806
forced HR mode hysteresis (FHH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 807
frequency band in use (BAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 808
GPRS non BCCH layer rxlev lower limit (GPL). . . . . . . . . . . . . . . . . . . 809
GPRS non BCCH layer rxlev upper limit (GPU) . . . . . . . . . . . . . . . . . . 811
hopping sequence number 1 (HSN1) . . . . . . . . . . . . . . . . . . . . . . . . . . 812
hopping sequence number 2 (HSN2) . . . . . . . . . . . . . . . . . . . . . . . . . . 813
HSCSD cell load lower limit (HCL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 814
HSCSD cell load upper limit (HCU) . . . . . . . . . . . . . . . . . . . . . . . . . . . 815
HSCSD regular cell load upper limit (HRCU) . . . . . . . . . . . . . . . . . . . . 816
HSCSD TCH capacity minimum (HTM) . . . . . . . . . . . . . . . . . . . . . . . . 817
immediate SDCCH HO enabled (ISIC) . . . . . . . . . . . . . . . . . . . . . . . . . 818
initial MCS for ext area acknowledged mode (MCEA) . . . . . . . . . . . . . 820
initial MCS for ext area unacknowledged mode (MCEU) . . . . . . . . . . . 821
limit for triggering OSC DFR multiplexing (DFRLIM) . . . . . . . . . . . . . . 822
limit for triggering OSC DHR multiplexing (DHRLIM) . . . . . . . . . . . . . . 823
MAIO offset (MO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 826
MAIO Step (MS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 827
max GPRS capacity (CMAX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 828
mobile allocation frequency list (MAL) . . . . . . . . . . . . . . . . . . . . . . . . . 829
MS tx pwr min (PMIN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 830
nominal DL TX power (NDTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832
non BCCH layer offset (NBL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 833
path loss offset DL (DPLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 834
path loss offset UL (UPLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 835
PCU identifier (PCU ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 836
PCU PSW TBF density target (TBFT) . . . . . . . . . . . . . . . . . . . . . . . . . 837
PCU PSW TBF downgrade threshold (TBFD) . . . . . . . . . . . . . . . . . . . 838
PCU PSW TBF upgrade threshold (TBFU). . . . . . . . . . . . . . . . . . . . . . 840
PCU up to date (PUTD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 841
radius extension (EXT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 842
RX diversity (RDIV). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 844
rx signal level adjust (RXSLA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 845
RACH threshold of composite cell node 1-6 (RTCC1-6) . . . . . . . . . . . 847
Sector ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 848
STIRC enabled (STIRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 849
super radius extension (SEXT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850
TDSCDMA NCCR enabled (TNENA) . . . . . . . . . . . . . . . . . . . . . . . . . . 851
transport type (TRAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 852
tx signal level adjust (TXSLA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853
UL coding scheme in acknowledged mode (UCSA) . . . . . . . . . . . . . . . 855
UL Coding Scheme In Ext Area Acknowledged Mode (UCSEA) . . . . . 856
UL coding scheme in ext area unacknowledged mode (UCSEU) . . . . 858
UL coding scheme in unacknowledged mode (UCSU). . . . . . . . . . . . . 860
UL noise level (ULN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 861
UL radio link timeout increase step (URIS) . . . . . . . . . . . . . . . . . . . . . . 862
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
10.127
10.128
10.129
10.130
10.131
10.132
underlay BTS hopping mode (UHOP) . . . . . . . . . . . . . . . . . . . . . . . . .
underlay hopping sequence number (UHSN) . . . . . . . . . . . . . . . . . . .
underlay MAIO offset (UMO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
underlay MAIO step (UMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
underlay mobile allocation frequency list (UMAL) . . . . . . . . . . . . . . . .
8k TRAU enabled for DFR (DFR8K). . . . . . . . . . . . . . . . . . . . . . . . . .
11
SEG-specific Base Transceiver Station (SEG-BTS) radio network object
parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 871
adjacency on other band (DBC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 871
allow IMSI attach detach (ATT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872
AMH lower load threshold (ALT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873
AMH max load of target cell (AML) . . . . . . . . . . . . . . . . . . . . . . . . . . . 874
AMH upper load threshold (AUT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875
AMR HR radio link timeout (AHRLT) . . . . . . . . . . . . . . . . . . . . . . . . . . 876
AMR lower limit for SEG FR resources (AFRL) . . . . . . . . . . . . . . . . . . 877
AMR Radio Link Timeout (ARLT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 879
AMR upper limit for SEG FR resources (AFRU) . . . . . . . . . . . . . . . . . 880
apply repeated FACCH (ARF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
averaging period (AP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 882
BCCH allocation usage for active MS (ACT) . . . . . . . . . . . . . . . . . . . . 883
BTS colour code (BCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 884
BTS load threshold (BLT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 886
BTS measure average (BMA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 887
BCSU index (BCSU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888
CA List Per BTS Enabled (CABE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 889
call reestablishment allowed (RE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 890
carrier unit configuration (CUCONF) . . . . . . . . . . . . . . . . . . . . . . . . . . 891
cell bar qualify (QUA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 893
cell barred (BAR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 894
cell identity (CI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 895
cell load for channel search (CLC). . . . . . . . . . . . . . . . . . . . . . . . . . . . 896
cell reselect hysteresis (HYS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 897
cell reselect offset (REO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898
cell reselection parameter index (PI) . . . . . . . . . . . . . . . . . . . . . . . . . . 899
cell type (CTY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900
coding scheme hop (CODH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902
coding scheme no hop (COD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 903
direct GPRS access BTS (DIRE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 904
directed retry method (DRM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 905
directed retry used (DR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906
DL adaption probability threshold (DLA) . . . . . . . . . . . . . . . . . . . . . . . 907
DL BLER crosspoint for CS selection hop (DLBH) . . . . . . . . . . . . . . . 908
DL BLER crosspoint for CS selection no hop (DLB) . . . . . . . . . . . . . . 909
DTM enabled (DENA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910
2G TRX power down threshold (PWDT) . . . . . . . . . . . . . . . . . . . . . . . 911
2G TRX power up threshold (PWUT) . . . . . . . . . . . . . . . . . . . . . . . . . 913
DTX Mode (DTX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 914
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
11.10
11.11
11.12
11.13
11.14
11.15
11.16
11.17
11.18
11.19
11.20
11.21
11.22
11.23
11.24
11.25
11.26
11.27
11.28
11.29
11.30
11.31
11.32
11.33
11.34
11.35
11.36
11.37
11.38
11.39
DN9813866
Id:0900d8058089b098
Confidential
863
864
865
867
868
869
17
BSS Radio Network Parameter Dictionary
11.40
11.41
11.42
11.43
11.44
11.45
11.46
11.47
11.48
11.49
11.50
11.51
11.52
11.53
11.54
11.55
11.56
11.57
11.58
11.59
11.60
11.61
11.62
11.63
11.64
11.65
11.66
11.67
11.68
11.69
11.70
11.71
11.72
11.73
11.74
11.75
11.76
11.77
11.78
11.79
11.80
11.81
11.82
11.83
11.84
11.85
11.86
18
early sending indication (ESI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915
EGPRS link adaptation enabled (ELA) . . . . . . . . . . . . . . . . . . . . . . . . . 916
emergency call restricted (EC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917
enable temporary overpower (ETOP) . . . . . . . . . . . . . . . . . . . . . . . . . . 918
extended cell for GPRS/EDGE enabled (EXGENA) . . . . . . . . . . . . . . . 920
extended cell location keep period (EXKEEP). . . . . . . . . . . . . . . . . . . 921
extended BCCH enabled (EBENA). . . . . . . . . . . . . . . . . . . . . . . . . . . . 923
FACCH busy threshold (FACHBT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 924
fdd and tdd cell reselect offset (FDD) . . . . . . . . . . . . . . . . . . . . . . . . . . 925
GPRS DL PC Enabled (DLPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 926
GPRS enabled (GENA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927
GPRS MS txpwr max cch (GTXP1) . . . . . . . . . . . . . . . . . . . . . . . . . . . 928
gprs ms txpwr max cch 1x00 (GTXP2) . . . . . . . . . . . . . . . . . . . . . . . . . 929
GPRS rxlev access min (GRXP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 931
GPRS threshold to search UTRAN cells (QSRP) . . . . . . . . . . . . . . . . . 932
HCS threshold (HCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 934
HSCSD downgrade guard time (HDT) . . . . . . . . . . . . . . . . . . . . . . . . . 935
HSCSD minimum exhaust (HME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 936
HSCSD upgrade gain (HUG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 937
HSCSD upgrade guard time (HUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 938
identification of BCCH frequency list (IDLE) . . . . . . . . . . . . . . . . . . . . . 939
IMSI based handover GSM enabled (IGE) . . . . . . . . . . . . . . . . . . . . . . 941
IMSI based handover WCDMA enabled (IWE). . . . . . . . . . . . . . . . . . . 942
initial MCS for acknowledged mode (MCA) . . . . . . . . . . . . . . . . . . . . . 944
initial MCS for ext area acknowledged mode (MCEA) . . . . . . . . . . . . . 945
initial MCS for ext area unacknowledged mode (MCEU) . . . . . . . . . . . 946
initial MCS for unacknowledged mode (MCU) . . . . . . . . . . . . . . . . . . . 947
intelligent directed retry used (IDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 948
interval measurement report sending (IMREPS) . . . . . . . . . . . . . . . . . 949
limit for free TCHs (LIMIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
location area code (LAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 951
lower limit for FR TCH resources (FRL) . . . . . . . . . . . . . . . . . . . . . . . . 952
max number of repetition (NY1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953
max number of retransmission (RET) . . . . . . . . . . . . . . . . . . . . . . . . . . 954
max queue length (MQL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 955
max time limit directed retry (MADR) . . . . . . . . . . . . . . . . . . . . . . . . . . 956
maximum BLER in acknowledged mode (BLA) . . . . . . . . . . . . . . . . . . 957
maximum BLER in unacknowledged mode (BLU) . . . . . . . . . . . . . . . . 958
mean BEP offset 8PSK (MBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 959
mean BEP offset GMSK (MBG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 961
measurement BCCH Allocation list (MEAS) . . . . . . . . . . . . . . . . . . . . . 962
min time limit directed retry (MIDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 963
minimum fdd threshold (FDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 964
minimum fdd threshold offset (FDMO) . . . . . . . . . . . . . . . . . . . . . . . . . 965
minimum RSCP threshold (FDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 968
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
11.87
11.88
11.89
11.90
11.91
11.92
11.93
11.94
11.95
11.96
11.97
11.98
11.99
11.100
11.101
11.102
11.103
11.104
11.105
11.106
11.107
11.108
11.109
11.110
11.111
11.112
11.113
11.114
11.115
11.116
11.117
11.118
11.119
11.120
11.121
11.122
11.123
11.124
11.125
11.126
11.127
11.128
11.129
11.130
11.131
11.132
DN9813866
MSC HO control enabled (MHOENA) . . . . . . . . . . . . . . . . . . . . . . . . . 970
MS max distance in call setup (DMAX) . . . . . . . . . . . . . . . . . . . . . . . . 972
MS priority used (MPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 973
MS txpwr max CCH (TXP1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 974
MS txpwr max CCH1x00 (TXP2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 975
MS txpwr max GSM (PMAX1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977
MS txpwr max GSM1x00 (PMAX2). . . . . . . . . . . . . . . . . . . . . . . . . . . 978
multiband cell reporting (MBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 979
network colour code (NCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 980
network service entity identifier (NSEI) . . . . . . . . . . . . . . . . . . . . . . . . 981
new establishment causes support (NECI) . . . . . . . . . . . . . . . . . . . . . 982
not allowed access classes (ACC). . . . . . . . . . . . . . . . . . . . . . . . . . . . 983
number of blocks for access grant msg (AG). . . . . . . . . . . . . . . . . . . . 985
number of multiframes (MFR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986
number of slots spread trans (SLO). . . . . . . . . . . . . . . . . . . . . . . . . . . 987
number of traffic channels reserved for priority subscribers only (TCRP) .
989
packet service entity identifier (PSEI) . . . . . . . . . . . . . . . . . . . . . . . . . 990
penalty time (PET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 991
PLMN permitted (PLMN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 992
power offset (PO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 993
precise paging usage (PRECPG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 994
prefer BCCH frequency GPRS (BFG) . . . . . . . . . . . . . . . . . . . . . . . . . 995
priority class (PRC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 997
PCU index (PCU). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 998
queue priority used (QPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 999
queueing priority call (QPC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000
queueing priority non-urgent handover (QPN). . . . . . . . . . . . . . . . . . 1002
queueing priority urgent handover (QPH) . . . . . . . . . . . . . . . . . . . . . 1003
ra reselect hysteresis (RRH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1004
RACH busy threshold (RACHBT) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005
radio link timeout (RLT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006
repeated FACCH in DL (RFDL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
repeated FACCH in UL (RFUL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009
repeated SACCH in DL (RSDL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010
repeated SACCH in UL (RSUL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1012
repeated SACCH RX lev threshold DL (RSRDL). . . . . . . . . . . . . . . . 1013
repeated SACCH RX lev threshold UL (RSRUL). . . . . . . . . . . . . . . . 1014
reservation method used in trunk reservation (REM) . . . . . . . . . . . . 1016
restricted use of priority channels in incoming handover (RUP) . . . . 1017
routing area code (RAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1018
rxlev access min (RXP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1019
scale ord (SCO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1020
SDCCH measurement report sending (SMREPS). . . . . . . . . . . . . . . 1021
SEG identification (SEG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1022
SEG name (SEGNAME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1024
SMS CB used (CB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1025
Id:0900d8058089b098
Confidential
19
BSS Radio Network Parameter Dictionary
11.133
11.134
11.135
11.136
11.137
11.138
11.139
11.140
11.141
11.142
11.143
11.144
11.145
11.146
11.147
11.148
11.149
11.150
11.151
11.152
11.153
11.154
Table Identification (TBL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1026
TCH rate intra-cell handover (TRIH) . . . . . . . . . . . . . . . . . . . . . . . . . . 1027
temporary offset (TEO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1029
threshold to search UTRAN cells (QSRI) . . . . . . . . . . . . . . . . . . . . . . 1030
time limit call (TLC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1032
time limit handover (TLH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1033
timer for periodic MS location updating (PER) . . . . . . . . . . . . . . . . . . 1034
traffic types (TT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035
TRHO guard time (TGT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036
trunk reservation used (TR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037
TRX priority in TCH allocation (TRP) . . . . . . . . . . . . . . . . . . . . . . . . . 1038
TX diversity time shift (TXDIV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1039
UL adaption probability threshold (ULA) . . . . . . . . . . . . . . . . . . . . . . . 1041
UL BLER crosspoint for CS selection hop (ULBH) . . . . . . . . . . . . . . . 1042
UL BLER crosspoint for CS selection no hop (ULB) . . . . . . . . . . . . . . 1043
upper limit for FR TCH resources (FRU) . . . . . . . . . . . . . . . . . . . . . . 1044
merged PGSM900 and EGSM900 enabled (MPE). . . . . . . . . . . . . . . 1045
WCDMA priority (WPRIO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1046
GPRS capacity throughput factor (GCTF) . . . . . . . . . . . . . . . . . . . . . 1047
lower DL RX lev for BCCH TRX preference (LDRB) . . . . . . . . . . . . . 1048
master bts id () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050
upper DL RX lev for BCCH TRX preference (UDRB) . . . . . . . . . . . . . 1051
12
12.1
12.2
12.3
12.4
12.5
Circuit Switched Dynamic Abis Pool (CSDAP) radio network object parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1053
BCF abis IF (BAIF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1053
BCF timeslot shift (SHIFT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1054
circuit (CRCT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1055
CSDAP id (CID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1056
pool size (SIZE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1057
13
13.1
13.2
13.3
13.4
13.5
13.6
Dynamic Abis Pool (DAP) radio network object parameters. . . . . . . . 1059
BCSU ID (BCSU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1059
circuit (CRCT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1060
packet service entity identifier (PSEI) . . . . . . . . . . . . . . . . . . . . . . . . . 1061
PCU index (PCU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1063
pool identification (ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1064
pool size (SIZE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1065
14
Exchange Terminal for Packet transport (ETP) radio network object parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067
BCSU index, PCU index () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067
BCSU index (BCSU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1068
ETP group ID (ETPGID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069
ETP type (ETPT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1071
ETME hardware index (ETMEID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1072
PCU index (PCU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073
SyncE Mode (SEM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074
Used ETP ID (UETPID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1076
14.1
14.2
14.3
14.4
14.5
14.6
14.7
14.8
20
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
DN9813866
15
15.1
15.2
15.3
15.4
15.5
15.6
15.7
15.8
GPRS Control (GPC) radio network object parameters. . . . . . . . . . .
NCCR number of zero results (NNZR) . . . . . . . . . . . . . . . . . . . . . . .
NCCR other PCU cell offset (NOPO). . . . . . . . . . . . . . . . . . . . . . . . .
NCCR rxlev idle mode window size (NRIW) . . . . . . . . . . . . . . . . . . .
NCCR rxlev transfer mode window size (NRTW) . . . . . . . . . . . . . . .
QC EGPRS DL RLC ack throughput threshold (QEDRT) . . . . . . . . .
QC EGPRS UL RLC ack throughput threshold (QEURT) . . . . . . . . .
QC GPRS DL RLC ack throughput (QGDRT) . . . . . . . . . . . . . . . . . .
QC GPRS UL RLC ack throughput (QGURT) . . . . . . . . . . . . . . . . . .
1078
1078
1079
1080
1081
1082
1083
1084
1085
16
16.1
16.2
16.3
16.4
16.5
16.6
16.7
16.8
16.9
16.10
16.11
16.12
16.13
16.14
16.15
16.16
16.17
16.18
16.19
16.20
16.21
16.22
16.23
16.24
16.25
16.26
16.27
16.28
16.29
16.30
16.31
16.32
16.33
16.34
16.35
16.36
16.37
Handover Control (HOC) radio network object parameters . . . . . . . .
800 reporting offset (R8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
800 reporting threshold (RT8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
900 reporting offset (R9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
900 reporting threshold (RT9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1800 reporting offset (R18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1800 reporting threshold (RT18) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1900 reporting offset (R19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1900 reporting threshold (RT19) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
adjacent cell averaging window size (AWS) . . . . . . . . . . . . . . . . . . .
adjacent WCDMA RAN cell averaging window size (UAWS) . . . . . .
advanced compression HO for AMR (ACHOA) . . . . . . . . . . . . . . . . .
all adjacent cells averaged (AAC) . . . . . . . . . . . . . . . . . . . . . . . . . . .
all adjacent WCDMA RAN cells averaged (UAAC) . . . . . . . . . . . . . .
all interfering cells averaged (AVER) . . . . . . . . . . . . . . . . . . . . . . . . .
AMH traffic control IUO (ATCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMH traffic control MCN (ATCM). . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMH TRHO pbgt margin (ATPM) . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I estimation method (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
count of successive rapid field drop thresholds (CNT) . . . . . . . . . . .
deep dropping EDGE monitoring window (ERMW) . . . . . . . . . . . . . .
enable enhanced rapid field drop (ERFD) . . . . . . . . . . . . . . . . . . . . .
enable fast averaging call setup (EFA) . . . . . . . . . . . . . . . . . . . . . . .
enable fast averaging HO (EFH) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
enable fast averaging PC (EFP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
enable inter FRT handover (EFHO). . . . . . . . . . . . . . . . . . . . . . . . . .
enable intracell handover interference DL (EIH) . . . . . . . . . . . . . . . .
enable intracell handover interference UL (EIC) . . . . . . . . . . . . . . . .
enable MS distance process (EMS). . . . . . . . . . . . . . . . . . . . . . . . . .
enable power budget handover (EPB). . . . . . . . . . . . . . . . . . . . . . . .
enable SDCCH handover (ESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
enable hierarchical cell handover (EHC) . . . . . . . . . . . . . . . . . . . . . .
enable TCH assignment super IUO (ETA). . . . . . . . . . . . . . . . . . . . .
enable umbrella handover (EUM) . . . . . . . . . . . . . . . . . . . . . . . . . . .
enhanced rapid field drop duration (ERD) . . . . . . . . . . . . . . . . . . . . .
reporting offset (FR). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
reporting threshold (FRT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fdd reporting threshold 2 (FRT2) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1087
1087
1088
1089
1090
1091
1092
1093
1094
1096
1096
1097
1099
1100
1101
1102
1103
1104
1105
1106
1107
1107
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
Id:0900d8058089b098
Confidential
21
BSS Radio Network Parameter Dictionary
16.38
16.39
16.40
16.41
16.42
16.43
16.44
16.45
16.46
16.47
16.48
16.49
16.50
16.51
16.52
16.53
16.54
16.55
16.56
16.57
16.58
16.59
16.60
16.61
16.62
16.63
16.64
16.65
16.66
16.67
16.68
16.69
16.70
16.71
16.72
16.73
16.74
16.75
16.76
16.77
16.78
16.79
16.80
16.81
16.82
16.83
16.84
22
GSM PLMN priorisation (GPP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125
handover period power budget (HPP) . . . . . . . . . . . . . . . . . . . . . . . . 1127
handover period umbrella (HPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127
inter-system direct access enabled (IDE) . . . . . . . . . . . . . . . . . . . . . . 1128
interfering cell averaging window size (SIZE) . . . . . . . . . . . . . . . . . . . 1129
interfering cell number of zero results (ZERO) . . . . . . . . . . . . . . . . . . 1130
intra HO lower rx level limit AMR HR (LLLAMR). . . . . . . . . . . . . . . . . 1131
intra HO lower rx quality limit AMR (LQLAMR) . . . . . . . . . . . . . . . . . . 1132
intra HO threshold Rx qual AMR FR (IHRF) . . . . . . . . . . . . . . . . . . . . 1134
intra HO threshold Rx qual AMR FR to DFR (IHRDFR) . . . . . . . . . . . 1135
Intra HO threshold Rx qual AMR HR (IHRH) . . . . . . . . . . . . . . . . . . . 1136
intra HO upper rx level limit AMR HR (ULLAMR) . . . . . . . . . . . . . . . . 1137
invalid BSIC reporting (IBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1138
level downlink weighting (LDW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1139
level downlink window size (LDWS) . . . . . . . . . . . . . . . . . . . . . . . . . . 1141
level uplink weighting (LUW). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1141
level uplink window size (LUWS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1143
lower C/I limit for band 1-6 (L1-L6) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1143
lower speed limit (LSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145
min int between HO req (MIH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1146
min int between unsucc HO attempt (MIU) . . . . . . . . . . . . . . . . . . . . . 1147
min interval between IUO HO req BQ (MIR) . . . . . . . . . . . . . . . . . . . . 1148
min interval between unsucc ISHO attempt (UMIU) . . . . . . . . . . . . . . 1149
min interval between unsucc IUO HO (MIO). . . . . . . . . . . . . . . . . . . . 1150
min traffic load for speech call (LTSC) . . . . . . . . . . . . . . . . . . . . . . . . 1151
minimum BSIC decode time (TIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1152
modified averaging window (ERAW) . . . . . . . . . . . . . . . . . . . . . . . . . 1152
modified number of zero results (ERZ) . . . . . . . . . . . . . . . . . . . . . . . . 1153
MS distance averaging window size (MSWS) . . . . . . . . . . . . . . . . . . 1154
MS distance HO threshold ext cell max (MAX). . . . . . . . . . . . . . . . . . 1155
MS distance HO threshold ext cell min (MIN) . . . . . . . . . . . . . . . . . . . 1157
MS distance HO threshold super ext cell max (SMAX) . . . . . . . . . . . 1158
MS distance HO threshold super ext cell min (SMIN). . . . . . . . . . . . . 1159
MS distance threshold param MS max range (MSR) . . . . . . . . . . . . . 1161
MS distance threshold param Nx (MSN) . . . . . . . . . . . . . . . . . . . . . . 1161
MS distance threshold param Px (MSP) . . . . . . . . . . . . . . . . . . . . . . . 1162
MS speed averaging (MSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1163
MS speed detection state (SDS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1164
MS speed threshold Nx (STN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1165
MS speed threshold Px (STP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1166
non BCCH layer access threshold (LAR) . . . . . . . . . . . . . . . . . . . . . . 1167
non BCCH layer exit threshold (LER) . . . . . . . . . . . . . . . . . . . . . . . . . 1169
non BCCH layer exit threshold nx (LEN) . . . . . . . . . . . . . . . . . . . . . . 1170
non BCCH layer exit threshold px (LEP). . . . . . . . . . . . . . . . . . . . . . . 1171
number of measured cells (FDMR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1172
number of WCDMA RAN zero results (UNOZ) . . . . . . . . . . . . . . . . . . 1173
number of zero results (NOZ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1174
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
16.85
16.86
16.87
16.88
16.89
16.90
16.91
16.92
16.93
16.94
16.95
16.96
16.97
16.98
16.99
16.100
16.101
16.102
16.103
16.104
16.105
16.106
16.107
16.108
16.109
16.110
16.111
16.112
16.113
16.114
16.115
16.116
16.117
16.118
16.119
16.120
16.121
16.122
16.123
16.124
16.125
16.126
16.127
16.128
16.129
16.130
16.131
DN9813866
OSC demultiplexing ul Rx level margin (ODMRG) . . . . . . . . . . . . . .
OSC DFR demultiplexing Rx quality threshold (ODFDQT) . . . . . . . .
OSC DFR demultiplexing UL Rx level margin (OFDMRG) . . . . . . . .
OSC DHR demultiplexing Rx quality threshold (ODDQT) . . . . . . . .
OSC DFR multiplexing Rx quality threshold (ODFMQT) . . . . . . . . .
OSC DFR multiplexing UL Rx level threshold (OFMLT) . . . . . . . . . .
OSC DFR multiplexing UL Rx level window (OFMLW) . . . . . . . . . . .
OSC DHR demultiplexing ul Rx level margin (ODMRG). . . . . . . . . .
OSC DHR multiplexing Rx quality threshold (ODMQT) . . . . . . . . . .
OSC DHR multiplexing ul Rx level threshold (OMLT). . . . . . . . . . . .
OSC DHR multiplexing ul Rx level window (OMLW) . . . . . . . . . . . .
OSC multiplexing ul Rx level threshold (OMLT) . . . . . . . . . . . . . . . .
OSC multiplexing ul Rx level window (OMLW) . . . . . . . . . . . . . . . . .
priority adjustment step for band 1-7 (P1-P7) . . . . . . . . . . . . . . . . . .
quality downlink weighting (QDW) . . . . . . . . . . . . . . . . . . . . . . . . . . .
quality downlink window size (QDWS). . . . . . . . . . . . . . . . . . . . . . . .
quality uplink weighting (QUW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
quality uplink window size (QUWS) . . . . . . . . . . . . . . . . . . . . . . . . . .
reporting rate (REP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
serving band reporting (SBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
super radius extension (SEXT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
super reuse bad C/I threshold (BCI) . . . . . . . . . . . . . . . . . . . . . . . . .
super reuse bad C/I threshold AMR FR (BCIF) . . . . . . . . . . . . . . . . .
super reuse bad C/I threshold AMR HR (BCIH) . . . . . . . . . . . . . . . .
super reuse bad C/I threshold Nx (BNX) . . . . . . . . . . . . . . . . . . . . . .
super reuse bad C/I threshold Px (BPX) . . . . . . . . . . . . . . . . . . . . . .
super reuse bad threshold Nx (CBN). . . . . . . . . . . . . . . . . . . . . . . . .
super reuse bad threshold Px (CBP) . . . . . . . . . . . . . . . . . . . . . . . . .
super reuse bad threshold Rx level (CBR) . . . . . . . . . . . . . . . . . . . .
super reuse estimation method (METH) . . . . . . . . . . . . . . . . . . . . . .
super reuse good C/I threshold (GCI) . . . . . . . . . . . . . . . . . . . . . . . .
super reuse good C/I threshold AMR FR (GCIF). . . . . . . . . . . . . . . .
super reuse good C/I threshold AMR HR (GCIH) . . . . . . . . . . . . . . .
super reuse good C/I threshold Nx (GNX) . . . . . . . . . . . . . . . . . . . . .
super reuse good C/I threshold Px (GPX) . . . . . . . . . . . . . . . . . . . . .
super reuse good threshold Nx (CGN) . . . . . . . . . . . . . . . . . . . . . . .
super reuse good threshold Px (CGP). . . . . . . . . . . . . . . . . . . . . . . .
super reuse good threshold Rx level (CGR) . . . . . . . . . . . . . . . . . . .
threshold deep dropping EDGE (ERT) . . . . . . . . . . . . . . . . . . . . . . .
threshold deep dropping EDGE Nx (ERN). . . . . . . . . . . . . . . . . . . . .
threshold deep dropping EDGE Px (ERP) . . . . . . . . . . . . . . . . . . . . .
threshold dl Rx qual AMR HR (QDRH) . . . . . . . . . . . . . . . . . . . . . . .
threshold dl Rx qual AMR FR (QDRF). . . . . . . . . . . . . . . . . . . . . . . .
threshold Dl Rx qual DFR (TDRQDF) . . . . . . . . . . . . . . . . . . . . . . . .
threshold Ul Rx qual DFR (TURQDF) . . . . . . . . . . . . . . . . . . . . . . . .
threshold for multi-RAT MS (QSRC) . . . . . . . . . . . . . . . . . . . . . . . . .
threshold interference downlink Nx (IDN) . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
1174
1176
1177
1178
1179
1181
1182
1183
1184
1186
1187
1188
1189
1190
1191
1192
1193
1195
1195
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1223
1224
1225
23
BSS Radio Network Parameter Dictionary
16.132
16.133
16.134
16.135
16.136
16.137
16.138
16.139
16.140
16.141
16.142
16.143
16.144
16.145
16.146
16.147
16.148
16.149
16.150
16.151
16.152
16.153
16.154
16.155
16.156
threshold interference downlink Px (IDP) . . . . . . . . . . . . . . . . . . . . . . 1226
threshold interference downlink Rx level (IDR). . . . . . . . . . . . . . . . . . 1227
threshold interference uplink Nx (IUN) . . . . . . . . . . . . . . . . . . . . . . . . 1228
threshold interference uplink Px (IUP) . . . . . . . . . . . . . . . . . . . . . . . . 1229
threshold interference uplink Rx level (IUR) . . . . . . . . . . . . . . . . . . . . 1230
threshold level downlink Nx (LDN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1230
threshold level downlink Px (LDP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1232
threshold level downlink Rx level (LDR) . . . . . . . . . . . . . . . . . . . . . . . 1233
threshold level uplink for rapid field drop (RPD) . . . . . . . . . . . . . . . . . 1234
threshold level uplink Nx (LUN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1234
threshold level uplink Px (LUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1236
threshold level uplink Rx level (LUR) . . . . . . . . . . . . . . . . . . . . . . . . . 1237
threshold qual downlink Nx (QDN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1238
threshold qual downlink Px (QDP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1239
threshold qual downlink Rx qual (QDR) . . . . . . . . . . . . . . . . . . . . . . . 1240
threshold qual uplink Nx (QUN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1241
threshold qual uplink Px (QUP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1242
threshold qual uplink Rx qual (QUR) . . . . . . . . . . . . . . . . . . . . . . . . . 1243
threshold ul Rx qual AMR FR (QURF) . . . . . . . . . . . . . . . . . . . . . . . . 1244
threshold ul Rx qual AMR HR (QURH) . . . . . . . . . . . . . . . . . . . . . . . . 1245
triggering ratio for WCDMA RAN cell penalty (TRW) . . . . . . . . . . . . . 1246
threshold dl Rx qual DHR (TDRQD) . . . . . . . . . . . . . . . . . . . . . . . . . . 1247
threshold ul Rx qual DHR (TURQD) . . . . . . . . . . . . . . . . . . . . . . . . . . 1249
upper speed limit (USL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250
WCDMA RAN cell penalty time (WCP). . . . . . . . . . . . . . . . . . . . . . . . 1251
17
High-Level Data Link Control (HDLC) radio network object parameters . .
1253
HDLC bandwith (HBAND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1253
HDLC Link ID (HNBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1254
HDLC link name (HNAME) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1255
HDLC PCM ID (HPCM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1256
HDLC start TSL (HTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1257
17.1
17.2
17.3
17.4
17.5
18
24
18.1
18.2
18.3
Location Area Code to Signalling Point Code (LAC to SPC) radio network
object parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259
location area code (LAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259
mapping entry index (MEI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1260
signaling point code (SPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1261
19
19.1
19.2
19.3
19.4
19.5
19.6
19.7
19.8
Location Services Element (LCSE) radio network object parameters 1263
altitude of ground level (AL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1263
antenna bearing (ABE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1264
antenna height (AHE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1265
antenna horizontal half power beam width (AHB). . . . . . . . . . . . . . . . 1265
BCCH frequency (FREQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1266
BTS colour code (BCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1268
cell identification (CI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1269
city type (CIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1269
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
19.9
19.10
19.11
19.12
19.13
19.14
19.15
19.16
19.17
19.18
19.19
19.20
19.21
19.22
19.23
latitude degrees (LAD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
latitude fractions (LAF). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
latitude minutes (LAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
latitude seconds (LAS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
latitude sign (LADS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
location area code (LAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
longitude degrees (LOD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
longitude fractions (LOF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
longitude minutes (LOM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
longitude seconds (LOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
longitude sign (LODS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
maximum radiated power (MRP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
network colour code (NCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
predicted back serving radius (BSR) . . . . . . . . . . . . . . . . . . . . . . . . .
predicted front serving radius (FSR) . . . . . . . . . . . . . . . . . . . . . . . . .
20
Location Measurement Unit Area (LMUA) radio network object parameters
1286
BCF identification (BCF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1286
frame number offset (FNO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1287
lmu fno 26-multiplier usage (FMU). . . . . . . . . . . . . . . . . . . . . . . . . . . 1288
lmu tsl fn delay (LTD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1289
LMU area identification (LMUA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1290
LMU TSL fn offset (LTO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1291
transmission equipment (TRE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1292
20.1
20.2
20.3
20.4
20.5
20.6
20.7
21
21.1
21.2
21.3
21.4
21.5
21.6
Mobile allocation frequency list (MA/MAL) radio network object parameters
1294
DFCA MA List Group ID (DMAG) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1294
DFCA MA list state (MALS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1295
DFCA MA list usage (DMAU). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1296
frequency (FREQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1298
identification of mobile allocation frequency list (-) . . . . . . . . . . . . . . 1299
type of mobile allocation frequency list (-) . . . . . . . . . . . . . . . . . . . . . 1300
22
22.1
22.2
22.3
22.4
22.5
22.6
Network Service Entity (NSE) radio network object parameters . . . . 1302
local UDP port number (LPNBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1302
network service entity identifier (NSEI) . . . . . . . . . . . . . . . . . . . . . . . 1303
NSE NRI mask (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1304
NSE Status (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1305
NSE type (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1306
network resource identifier in decimal or network resource identifier in binary (NRID or NRIB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1307
23
Network Service Virtual Connection (NSVC) radio network object parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1309
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1309
bearer channel identfier (BCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1310
bearer channel name (BCN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1310
committed information rate (CIR). . . . . . . . . . . . . . . . . . . . . . . . . . . . 1311
23.1
23.2
23.3
23.4
DN9813866
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
Id:0900d8058089b098
Confidential
25
BSS Radio Network Parameter Dictionary
26
23.5
23.6
23.7
data link connection identifier (DLCI) . . . . . . . . . . . . . . . . . . . . . . . . . 1312
network service virtual connection identifier (NSVCI) . . . . . . . . . . . . . 1313
network service virtual connection name (NAME) . . . . . . . . . . . . . . . 1314
24
24.1
24.2
24.3
24.4
24.5
24.6
24.7
24.8
24.9
Network Service Virtual Link (NSVL) radio network object parameters . . .
1316
Network Service Virtual Link Identifier (NSVLI) . . . . . . . . . . . . . . . . . 1316
network service virtual link name (-) . . . . . . . . . . . . . . . . . . . . . . . . . . 1317
NSE NRI mask (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1318
preconfigured SGSN IP endpoint (PRE) . . . . . . . . . . . . . . . . . . . . . . . 1319
remote data weight (RDW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1320
remote host name (RHOST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1321
Remote IP Address Value (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1322
remote signalling weight (RSW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1323
Remote UDP Port Number (RPNBR) . . . . . . . . . . . . . . . . . . . . . . . . . 1324
25
25.1
25.2
25.3
25.4
25.5
25.6
25.7
25.8
Packet Control Unit (PCU) radio network object parameters . . . . . . . 1326
abis interface type (AIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1326
BCSU ID (BCSU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1327
packet service entity identifier (PSEI) . . . . . . . . . . . . . . . . . . . . . . . . . 1328
PCU identifier (PCU ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1329
PCU Index (PCU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1330
PCU up to date (PUTD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1331
plug-in unit type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1332
pcu object state (POS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1334
26
26.1
26.2
26.3
26.4
26.5
26.6
26.7
26.8
26.9
26.10
26.11
26.12
26.13
26.14
26.15
26.16
26.17
26.18
26.19
26.20
26.21
26.22
Power Control (POC) radio network object parameters . . . . . . . . . . . 1336
ALA enabled (AENA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1336
BCCH TRX TX pwr reduction (TPR). . . . . . . . . . . . . . . . . . . . . . . . . . 1337
binary representation ALPHA (ALPHA) . . . . . . . . . . . . . . . . . . . . . . . 1338
binary representation TAU (GAMMA) . . . . . . . . . . . . . . . . . . . . . . . . . 1339
bit error probability filter averaging period (BEP) . . . . . . . . . . . . . . . . 1340
BS TX pwr max (PMAX1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1341
BS TX pwr max1x00 (PMAX2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1343
BS TX pwr min (PMIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1344
BS TX pwr offset (POFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1346
derived HO power security margin (DHOPSM) . . . . . . . . . . . . . . . . . 1347
DL PC default power reduction (PCPOW) . . . . . . . . . . . . . . . . . . . . . 1348
DL PC window size (PCWS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1350
estimated DL interference (EDLI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1352
idle mode signal strength filter period (IFP) . . . . . . . . . . . . . . . . . . . . 1353
maximum power compensation (MPC). . . . . . . . . . . . . . . . . . . . . . . . 1354
max DL power reduction (MDLPWR) . . . . . . . . . . . . . . . . . . . . . . . . . 1355
maximum Tx power of composite cell node 1-6 (MTPCC1-6) . . . . . . 1356
max UL power reduction (MULPWR) . . . . . . . . . . . . . . . . . . . . . . . . . 1358
min int between ALA (AMIN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1359
pc averaging lev dl weighting (LDW) . . . . . . . . . . . . . . . . . . . . . . . . . 1360
pc averaging lev dl window size (LDS) . . . . . . . . . . . . . . . . . . . . . . . . 1361
pc averaging lev ul weighting (LUW) . . . . . . . . . . . . . . . . . . . . . . . . . 1362
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
26.23
26.24
26.25
26.26
26.27
26.28
26.29
26.30
26.31
26.32
26.33
26.34
26.35
26.36
26.37
26.38
26.39
26.40
26.41
26.42
26.43
26.44
26.45
26.46
26.47
26.48
26.49
26.50
26.51
26.52
26.53
26.54
26.55
26.56
26.57
26.58
26.59
26.60
26.61
26.62
26.63
26.64
26.65
26.66
26.67
26.68
26.69
DN9813866
pc averaging lev ul window size (LUS) . . . . . . . . . . . . . . . . . . . . . . .
pc averaging qual dl weighting (QDW) . . . . . . . . . . . . . . . . . . . . . . .
pc averaging qual dl window size (QDS) . . . . . . . . . . . . . . . . . . . . . .
pc averaging qual ul weighting (QUW) . . . . . . . . . . . . . . . . . . . . . . .
pc averaging qual ul window size (QUS) . . . . . . . . . . . . . . . . . . . . . .
pc lower threshold dl Rx qual AMR FR (LDRF) . . . . . . . . . . . . . . . . .
pc lower threshold dl Rx qual AMR HR (LDRH) . . . . . . . . . . . . . . . .
pc lower threshold Dl Rx qual DFR (LDDFR) . . . . . . . . . . . . . . . . . .
pc lower threshold ul Rx qual AMR FR (LURF) . . . . . . . . . . . . . . . . .
pc lower threshold ul Rx qual AMR HR (LURH) . . . . . . . . . . . . . . . .
pc lower threshold Ul Rx qual DFR (LUDFR) . . . . . . . . . . . . . . . . . .
pc lower thresholds lev dl Nx (LDN). . . . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds lev dl Px (LDP) . . . . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds lev dl Rx level (LDR) . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds lev ul Nx (LUN). . . . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds lev ul Px (LUP) . . . . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds lev ul Rx level (LUR) . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual dl Nx (LDN) . . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual dl Px (LDP). . . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual dl Rx qual (LDR). . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual ul Nx (LUN) . . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual ul Px (LUP). . . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual ul RX qual (LUR) . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual144 Nx (LQN) . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual144 Px (LQP) . . . . . . . . . . . . . . . . . . . . . . .
pc lower thresholds qual144 Rx level (LQR) . . . . . . . . . . . . . . . . . . .
pc upper threshold Dl Rx qual DFR (UDDFR) . . . . . . . . . . . . . . . . . .
pc upper threshold dl Rx qual DHR (UDDHR) . . . . . . . . . . . . . . . . . .
pc upper threshold Ul Rx qual DFR (UUDFR) . . . . . . . . . . . . . . . . . .
pc upper threshold ul Rx qual DHR (UUDHR) . . . . . . . . . . . . . . . . . .
pc upper threshold dl Rx qual AMR FR (UDRF) . . . . . . . . . . . . . . . .
pc upper threshold dl Rx qual AMR HR (UDRH) . . . . . . . . . . . . . . . .
pc upper threshold ul Rx qual AMR FR (UURF) . . . . . . . . . . . . . . . .
pc upper threshold ul Rx qual AMR HR (UURH) . . . . . . . . . . . . . . . .
pc upper thresholds lev dl Nx (UDN) . . . . . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds lev dl Px (UDP) . . . . . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds lev dl Rx level (UDR) . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds lev ul Nx (UUN) . . . . . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds lev ul Px (UUP) . . . . . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds lev ul Rx level (UUR) . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds qual dl Nx (UDN) . . . . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds qual dl Px (UDP) . . . . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds qual dl Rx qual (UDR) . . . . . . . . . . . . . . . . . . . .
pc upper thresholds qual ul Nx (UUN) . . . . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds qual ul Px (UUP) . . . . . . . . . . . . . . . . . . . . . . . .
pc upper thresholds qual ul Rx qual (UUR) . . . . . . . . . . . . . . . . . . . .
power control interval (INT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
1363
1364
1365
1366
1367
1368
1369
1370
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1388
1389
1390
1392
1393
1394
1395
1397
1398
1399
1400
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
27
BSS Radio Network Parameter Dictionary
28
26.70
26.71
26.72
26.73
26.74
26.75
26.76
26.77
26.78
26.79
26.80
26.81
26.82
power ctrl enabled (PENA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1415
power decr limit band 0 (PD0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1416
power decr limit band 1 (PD1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1417
power decr limit band 2 (PD2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1418
power decr qual factor (PDF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1419
power incr step size (INC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1420
power limit ALA (ALIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1421
power red step size (RED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1422
pc lower threshold dl Rx qual DHR (LDDHR) . . . . . . . . . . . . . . . . . . . 1423
pc lower threshold ul Rx qual DHR (LUDHR) . . . . . . . . . . . . . . . . . . . 1424
pc lower thresholds lev dl Rx level (LDR) . . . . . . . . . . . . . . . . . . . . . . 1426
pc lower thresholds lev ul Rx level (LUR) . . . . . . . . . . . . . . . . . . . . . . 1427
transfer mode signal strength filter period (TFP) . . . . . . . . . . . . . . . . 1428
27
27.1
27.2
27.3
27.4
Packet Service Entity (PSE) radio network object parameters . . . . . . 1430
null NRI in decimal or null NRI in binary (NNRID or NNRIB) . . . . . . . 1430
packet service entity identifier (PSEI) . . . . . . . . . . . . . . . . . . . . . . . . . 1431
PSE NRI mask (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1432
SGSN load balancing (SLBAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1433
28
28.1
28.2
28.3
28.4
28.5
Routing Area (RA) radio network object parameters . . . . . . . . . . . . . 1435
location area code (LAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1435
mobile country code (MCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1436
mobile network code (MNC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1437
network service entity identifier (NSEI) . . . . . . . . . . . . . . . . . . . . . . . . 1438
routing area code (RAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1439
29
29.1
29.2
29.3
29.4
29.5
29.6
29.7
29.8
29.9
29.10
29.11
29.12
29.13
29.14
29.15
29.16
29.17
29.18
29.19
29.20
29.21
Radio timeslot (RTSL) radio network object parameters . . . . . . . . . . 1441
Abis speech circuit/PCM (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1441
Abis speech circuit/PCM (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1442
Abis speech circuit/PCM (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1444
Abis speech circuit/PCM (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1446
Abis speech circuit/PCM (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1448
Abis speech circuit/PCM (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1449
Abis speech circuit/PCM (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1451
Abis speech circuit/PCM (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1452
Abis speech circuit/TSL (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1454
Abis speech circuit/TSL (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1455
Abis speech circuit/TSL (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1457
Abis speech circuit/TSL (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1459
Abis speech circuit/TSL (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1461
Abis speech circuit/TSL (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1463
Abis speech circuit/TSL (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1465
Abis speech circuit/TSL (PCMTSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 1467
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1469
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1470
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1472
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1473
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1474
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
29.22
29.23
29.24
29.25
29.26
29.27
29.28
29.29
29.30
29.31
29.32
administrative state (-) . . . .
administrative state (-) . . . .
administrative state (-) . . . .
RTSL type 0 (CH0) . . . . . .
RTSL type 1 (CH1) . . . . . .
RTSL type 2 (CH2) . . . . . .
RTSL type 3 (CH3) . . . . . .
RTSL type 4 (CH4) . . . . . .
RTSL type 5 (CH5) . . . . . .
RTSL type 6 (CH6) . . . . . .
RTSL type 7 (CH7) . . . . . .
......
......
......
......
......
......
......
......
......
......
......
1475
1476
1478
1479
1482
1485
1488
1491
1494
1497
1500
30
30.1
30.2
30.3
30.4
30.5
30.6
Subscriber Group (SG) radio network object parameters . . . . . . . . .
authorised networks identification (ANE) . . . . . . . . . . . . . . . . . . . . . .
home mobile country code (HMCC). . . . . . . . . . . . . . . . . . . . . . . . . .
home mobile network code (HMNC) . . . . . . . . . . . . . . . . . . . . . . . . .
subscriber group identification (SG). . . . . . . . . . . . . . . . . . . . . . . . . .
subscriber group name (NAME) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WCDMA RAN access (WA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1504
1504
1505
1506
1507
1507
1508
31
Serving Mobile Location Center (SMLC) radio network object parameters
1510
high response time (RTH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1510
LCS ignore limit (LIL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1511
low response time (RTL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1512
PBS halfrate limit (PHF). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1513
PBS stop limit (PSL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1514
31.1
31.2
31.3
31.4
31.5
32
32.1
32.2
33
DN9813866
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
......
......
......
......
......
......
......
......
......
......
......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
......
......
......
......
......
......
......
......
......
......
......
Text input and output (IO_TEXT/TID) radio network object parameters . .
1515
text ID (TID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1515
text string (TEXT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1516
33.1
33.2
33.3
Trunk Reservation Decision Threshold Table (TRK_TBL/TRKT) radio network object parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1518
decision threshold values (T1-T16) . . . . . . . . . . . . . . . . . . . . . . . . . . 1518
random value upper limit (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1519
table identification (TBL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1520
34
34.1
34.2
34.3
34.4
34.5
34.6
34.7
34.8
34.9
34.10
Transceiver (TRX) radio network object parameters . . . . . . . . . . . . .
administrative state (-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
autoconfigure (AC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
bb Unit Supports Edge (BB_UNIT) . . . . . . . . . . . . . . . . . . . . . . . . . .
binary outputs (ON/OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
bit rate (BR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I estimation type 1-10 (T1-T10) . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/I estimation weight 1-10 (W1-W10) . . . . . . . . . . . . . . . . . . . . . . . .
cell identification of interfering cell 1-10 (CI1-CI10) . . . . . . . . . . . . . .
combi link (CL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D-channel O & M link set name (ONAME). . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
1521
1521
1522
1523
1524
1525
1527
1528
1529
1529
1531
29
BSS Radio Network Parameter Dictionary
30
34.11
34.12
34.13
34.14
34.15
34.16
34.17
34.18
34.19
34.20
34.21
34.22
34.23
34.24
34.25
34.26
34.27
34.28
34.29
34.30
34.31
34.32
34.33
34.34
34.35
34.36
34.37
34.38
34.39
34.40
34.41
34.42
34.43
34.44
34.45
34.46
34.47
34.48
34.49
34.50
D-channel O&M link set number (ONBR) . . . . . . . . . . . . . . . . . . . . . . 1532
D-channel telecom link set name (DNAME) . . . . . . . . . . . . . . . . . . . . 1533
D-channel telecom link set number (DNBR) . . . . . . . . . . . . . . . . . . . . 1534
DFCA indication (DFCA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1535
direct access level (DAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1537
Double Power TRX Faulty (FLTY) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1538
dual TRX usage (DTRX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1539
dynamic abis pool ID (DAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1541
E-TRX type (ETRX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1542
frequency (FREQ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1544
GPRS enabled TRX (GTRX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1545
horizon associated TRX ID (HASSO) . . . . . . . . . . . . . . . . . . . . . . . . . 1547
horizon edge service type (ETYPE) . . . . . . . . . . . . . . . . . . . . . . . . . . 1548
horizon power finetune (HPOFT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1550
horizon TRX type (HTYPE). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1552
level adjustment 1-10 (L1-L10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1553
location area code of interfering cell 1-10 (LAC1-LAC10) . . . . . . . . . 1554
Metro TRX Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1555
mobile country code of interfering cell 1-10 (MCC1-MCC10) . . . . . . . 1556
mobile network code of interfering cell 1-10 (MNC1-MNC10) . . . . . . 1557
Number of TRX RF power levels (Number of TRX RF power levels) 1559
optimum RX level downlink (LEVD) . . . . . . . . . . . . . . . . . . . . . . . . . . 1560
optimum RX level uplink (LEV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1561
preferred BCCH TRX (PREF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1562
RF hopping allowed (RFHA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1563
Server TRX Id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1564
subslots for signalling (SIGN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1565
training sequence code (TSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1566
transceiver identification (TRX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1567
TRX DDU association (DDU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1569
TRX frequency type (FRT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1570
TRX half rate support (HRS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1571
TRX identification with frequency (IFREQ) . . . . . . . . . . . . . . . . . . . . . 1572
TRX MCPA number (TMCPAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1574
TRX MCPA position (TMCPAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1575
TRX MCPA port id (TMCPAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1576
TRX RF power (TRX RF power) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1577
TRX shutdown group (SDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1578
TRX OSC capability (). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1580
TRX Starting Mode () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1581
35
35.1
35.2
35.3
Transcoding Service Unit (TCSU) radio network object parameters . 1584
TCSU index (TCSUID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1584
TCSU number (TCNBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1585
TCSU operational state (TCSTA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1586
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
List of tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Table 27
Table 28
Table 29
Table 30
Table 31
Table 32
Table 33
Table 34
Table 35
Table 36
Table 37
Table 38
Table 39
Table 40
Table 41
Table 42
Table 43
Table 44
Table 45
DN9813866
How to read parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
ACP ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Pool Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
CI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Adjacent Cell Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Adjacent Cell Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
GPRS Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
AMR Target Cell Of Direct Access To Desired Layer . . . . . . . . . . . . . . 73
BCCH Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
BSIC BCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Reference Cell C/I Estimation Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Reference Cell CI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
IDR Cell Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Chained Adj Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Directed Retry Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
DTM Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
DTM Power Budget Margin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Enable Derived Handover Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Enable HO Margin Lev Qual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Fast Moving Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
GPRS MS Tx Pwr Max CCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
GPRS MS Tx Pwr Max CCH 1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
GPRS Penalty Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
GPRS Rxlev Access Min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
GPRS Temporary Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
HO margin delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
HCS Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
HO Level Umbrella . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
HO Load Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
HO Margin Lev . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
HO Margin PBGT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
HO Margin Qual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
HO Priority Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
HO Target Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
HO Target area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
IBNACC State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Reference Cell Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
LAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Reference Cell LAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Reference Cell MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
MNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Reference Cell MNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
MS Pwr Opt Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Id:0900d8058089b098
Confidential
31
BSS Radio Network Parameter Dictionary
Table 46
Table 47
Table 48
Table 49
Table 50
Table 51
Table 52
Table 53
Table 54
Table 55
Table 56
Table 57
Table 58
Table 59
Table 60
Table 61
Table 62
Table 63
Table 64
Table 65
Table 66
Table 67
Table 68
Table 69
Table 70
Table 71
Table 72
Table 73
Table 74
Table 75
Table 76
Table 77
Table 78
Table 79
Table 80
Table 81
Table 82
Table 83
Table 84
Table 85
Table 86
Table 87
Table 88
Table 89
Table 90
Table 91
Table 92
32
MS Tx Pwr Max GSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
MS Tx Pwr Max GSM1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
NCCR And DTM EGPRS PBGT Margin . . . . . . . . . . . . . . . . . . . . . . . 117
NCCR And DTM GPRS PBGT Margin . . . . . . . . . . . . . . . . . . . . . . . . 118
NCCR EGPRS Quality Margin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
NCCR GPRS Quality Margin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
BSIC NCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Priority Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Reporting Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
RAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
RX Lev Min Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Synchronised . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Target Cell Of Direct Access To Desired Layer . . . . . . . . . . . . . . . . . . 128
TRHO Target Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
ADJW ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Cell Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Cell Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Direct Access Ec/Io Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Downlink Transmission Diversity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
ISNCCR FDD Quality Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
LAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Minimum CPICH Ec/Io Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
MNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
RNC ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Reporting Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Scrambling Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Service Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Synchronisation Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
WCDMA Downlink Carrier Frequency . . . . . . . . . . . . . . . . . . . . . . . . . 146
ANE ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Authorised Networks Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Network MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Network MNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Network Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Barred LTE Adjacent Cell Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Barred LTE Adjacent Cell List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Barred LTE Adjacent Cell Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Barred LTE Adjacent Cell Pattern Sense . . . . . . . . . . . . . . . . . . . . . . . 157
LTE Adjacent Cell Downlink Carrier Frequency . . . . . . . . . . . . . . . . . . 158
LTE Adjacent Cell Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
LTE Adjacent Cell Mobile Country Code . . . . . . . . . . . . . . . . . . . . . . . 161
LTE Adjacent Cell Minimum Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . 162
LTE Adjacent Cell Min RX Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
LTE Adjacent Cell Mobile Network Code . . . . . . . . . . . . . . . . . . . . . . . 164
LTE Adjacent Cell Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
LTE Adjacent Cell Reselection Lower Threshold . . . . . . . . . . . . . . . . . 166
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 93
Table 94
Table 95
Table 96
Table 97
Table 98
Table 99
Table 100
Table 101
Table 102
Table 103
Table 104
Table 105
Table 106
Table 107
Table 108
Table 109
Table 110
Table 111
Table 112
Table 113
Table 114
Table 115
Table 116
Table 117
Table 118
Table 119
Table 120
Table 121
Table 122
Table 123
Table 124
Table 125
Table 126
Table 127
Table 128
Table 129
Table 130
Table 131
Table 132
Table 133
Table 134
Table 135
Table 136
Table 137
Table 138
Table 139
DN9813866
LTE Adjacent Cell Reselection Upper Threshold . . . . . . . . . . . . . . . .
LTE Adjacent Cell Tracking Area Code . . . . . . . . . . . . . . . . . . . . . . .
Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BAL ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type Of BCCH Frequency List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slave BCF List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Autoconfigure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Unlock Allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abis interface connection type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
attached CSDAP 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
attached CSDAP 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
attached CSDAP 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
attached CSDAP 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCCH TRX Shutdown Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCF ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS CU-plane IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS IPv4 Subnet Mask Length for C/U-plane . . . . . . . . . . . . . . . . . .
BTS IPv4 Subnet Mask Length for M-plane . . . . . . . . . . . . . . . . . . . .
BTS M-plane IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BSC-BSC interface failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS Battery Backup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS Site Subtype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCF HDLC ID list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCF Up to Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS C/U-plane IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS Commissioning State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS M-plane IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BU1 Abis Throughput Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BU2 Abis Throughput Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAPD Link Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAPD Link Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downlink Committed Information Rate . . . . . . . . . . . . . . . . . . . . . . . .
Downloaded SCF File Plan Id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Input Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Synchronization Source . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Ring/Path Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ETP BCF ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FACCH LAPDm T200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flexi EDGE Abis Over IP/Ethernet Feature Usage . . . . . . . . . . . . . . .
Flexi EDGE TRS Abis Grooming Feature Usage . . . . . . . . . . . . . . . .
Flexi EDGE TRS Loop Protection Feature Usage . . . . . . . . . . . . . . .
Flexi EDGE Additional 2 E1/T1 Feature Usage . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
167
169
170
171
172
174
175
177
178
179
182
183
184
185
186
188
189
190
192
193
194
195
197
199
200
202
203
205
206
207
208
210
211
214
215
216
217
218
219
221
222
223
225
226
227
228
229
33
BSS Radio Network Parameter Dictionary
Table 140
Table 141
Table 142
Table 143
Table 144
Table 145
Table 146
Table 147
Table 148
Table 149
Table 150
Table 151
Table 152
Table 153
Table 154
Table 155
Table 156
Table 157
Table 158
Table 159
Table 160
Table 161
Table 162
Table 163
Table 164
Table 165
Table 166
Table 167
Table 168
Table 169
Table 170
Table 171
Table 172
Table 173
Table 174
Table 175
Table 176
Table 177
Table 178
Table 179
Table 180
Table 181
Table 182
Table 183
Table 184
Table 185
Table 186
34
Header Compression For ML-PPP . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Header Compression For UDP IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
Identification Of Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
IPSec Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Master Clock BCF Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Master Clock TRX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Maximum BTS Multiplexing Wait Time . . . . . . . . . . . . . . . . . . . . . . . . 238
Maximum ETP Multiplexing Wait Time . . . . . . . . . . . . . . . . . . . . . . . . 239
Maximum Multiplexing Packet Size . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
MCPA Identity Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
MCPA Identity Port ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
MCPA Identity Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
MCPA Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
MCPA Power Pooling BCF Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
MCPA Power Pooling Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
OMUSIG Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Packet Abis BCF Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
PCM Port ID 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
PCM Port ID 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
PCM Port ID 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
PCM Port ID 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
PCM Port ID 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
PCM Port ID 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
PCM Port ID 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
PCM Port ID 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
Packet Abis Congestion Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Packet Abis Over Satellite in Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Packet Delay Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Packet Loss on DL Abis PL1 Threshold . . . . . . . . . . . . . . . . . . . . . . . 266
Packet Loss on DL Abis PL2 Threshold . . . . . . . . . . . . . . . . . . . . . . . 268
Packet TRS E1/T1 Feature Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
QoS Aware Ethernet Switch Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
RF Sharing State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
RX Difference Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
SDCCH LAPDm T200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
Severity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Site Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Synch Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Synch Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
System Module HW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Text ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Text ID Of The Output 1...6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
TRX Shutdown Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
TRX Shutdown Timer 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
TRX Shutdown Timer 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 187
Table 188
Table 189
Table 190
Table 191
Table 192
Table 193
Table 194
Table 195
Table 196
Table 197
Table 198
Table 199
Table 200
Table 201
Table 202
Table 203
Table 204
Table 205
Table 206
Table 207
Table 208
Table 209
Table 210
Table 211
Table 212
Table 213
Table 214
Table 215
Table 216
Table 217
Table 218
Table 219
Table 220
Table 221
Table 222
Table 223
Table 224
Table 225
Table 226
Table 227
Table 228
Table 229
Table 230
Table 231
Table 232
Table 233
DN9813866
UL Committed Burst Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL Committed Information Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uplink Traffic Shaping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Used CS UDP MUX port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Used PS UDP MUX port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vlan ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20W Power Licence Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Limit For Full Rate TCH Availability . . . . . . . . . . . . . . . . . . . . .
Alarm Limit For Half Rate TCH Availibility . . . . . . . . . . . . . . . . . . . . .
Alarm Limit For SDCCH Availability . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Threshold For Number Of Channel Seizure Requests . . . . . . .
Alarm Threshold For Number Of Channel Seizures . . . . . . . . . . . . . .
Alarm Threshold For SDCCH Congestion . . . . . . . . . . . . . . . . . . . . .
Alarm Threshold For SDCCH Failure Rate . . . . . . . . . . . . . . . . . . . . .
Alarm Threshold For TCH Congestion . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Threshold For TCH Failure Rate . . . . . . . . . . . . . . . . . . . . . . .
Alarm Threshold For The Share Of High TCH Interference . . . . . . . .
AMH Lower Load Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMH Max Load Of Target Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMH Upper Load Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMR Configuration In Handovers . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMR Lower Limit For FR Resources . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Lower Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Lower Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Lower Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Lower Threshold 4 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR HR Unpacking Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Upper Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Upper Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Upper Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL FR Upper Threshold 4 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Lower Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Lower Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Lower Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Lower Threshold 4 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Upper Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Upper Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Upper Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC DL HR Upper Threshold 4 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC UL FR Lower Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC UL FR Lower Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC UL FR Lower Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC UL FR Lower Threshold 4 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC UL FR Upper Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC UL FR Upper Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC UL FR Upper Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . .
AMR PPC UL FR Upper Threshold 4 . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
295
297
298
300
301
302
304
306
307
307
308
310
311
312
313
314
315
316
317
318
319
320
322
323
324
326
327
330
331
332
334
335
336
338
339
340
342
343
344
346
347
349
350
351
353
354
355
35
BSS Radio Network Parameter Dictionary
Table 234
Table 235
Table 236
Table 237
Table 238
Table 239
Table 240
Table 241
Table 242
Table 243
Table 244
Table 245
Table 246
Table 247
Table 248
Table 249
Table 250
Table 251
Table 252
Table 253
Table 254
Table 255
Table 256
Table 257
Table 258
Table 259
Table 260
Table 261
Table 262
Table 263
Table 264
Table 265
Table 266
Table 267
Table 268
Table 269
Table 270
Table 271
Table 272
Table 273
Table 274
Table 275
Table 276
Table 277
Table 278
Table 279
Table 280
36
AMR PPC UL HR Lower Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . . 357
AMR PPC UL HR Lower Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . . 358
AMR PPC UL HR Lower Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . . 359
AMR PPC UL HR Lower Threshold 4 . . . . . . . . . . . . . . . . . . . . . . . . . 361
AMR PPC UL HR Upper Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . . 362
AMR PPC UL HR Upper Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . . 363
AMR PPC UL HR Upper Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . . 365
AMR PPC UL HR Upper Threshold 4 . . . . . . . . . . . . . . . . . . . . . . . . . 366
AMR Set Grades Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
AMR Upper Limit For FR Resources . . . . . . . . . . . . . . . . . . . . . . . . . . 368
A-If AF1 WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
A-If AF2 WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
A-If AF3 WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
A-If AF4 WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
A-If BE WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
A-If CS U-plane DSCP PHB TC in BSS . . . . . . . . . . . . . . . . . . . . . . . . 376
A-If CS U-plane DSCP PHB TC in MGW . . . . . . . . . . . . . . . . . . . . . . . 377
Abis C-plane to DSCP Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
Abis M-plane to DSCP Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
Abis U-plane CS to DSCP Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Abis U-plane PS to DSCP Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
Background Traffic Class Scheduling Weight For ARP 1 . . . . . . . . . . 385
Background Traffic Class Scheduling Weight For ARP 2 . . . . . . . . . . 386
Background Traffic Class Scheduling Weight For ARP 3 . . . . . . . . . . 387
BCSU Load Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
BIM Confidence Probability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
BIM Interference Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
BIM Update Guard Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
BIM Update Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
BIM Update Scaling Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
BTS Site Battery Backup Forced HO Timer . . . . . . . . . . . . . . . . . . . . . 395
Backhaul Timer Duration Start Reaction . . . . . . . . . . . . . . . . . . . . . . . 396
Backhaul Timer Duration Stop Reaction . . . . . . . . . . . . . . . . . . . . . . . 398
C/I Target 14.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
C/I Target AMR FR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
C/I Target AMR HR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
C/I Target FR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402
DFCA C/I Target GPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
C/I Target HR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
C/I Target OSC DFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
C/I Target OSC DHR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
DFCA C/I Target SDCCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408
C/I Target UL Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
CN-ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
CS Load Balancing Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
CS MSC State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
CS NAS Node Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 281
Table 282
Table 283
Table 284
Table 285
Table 286
Table 287
Table 288
Table 289
Table 290
Table 291
Table 292
Table 293
Table 294
Table 295
Table 296
Table 297
Table 298
Table 299
Table 300
Table 301
Table 302
Table 303
Table 304
Table 305
Table 306
Table 307
Table 308
Table 309
Table 310
Table 311
Table 312
Table 313
Table 314
Table 315
Table 316
Table 317
Table 318
Table 319
Table 320
Table 321
Table 322
Table 323
Table 324
Table 325
Table 326
Table 327
DN9813866
CS NRI Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS NRI List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS TCH Allocation Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS TCH Allocation RTSL0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS Weight Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C-plane Packet Drop Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS Packet Drop Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS UDP-MUX Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock-sync to DSCP Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS Macrocell Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS Microcell Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Default Signalling Point Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delay Of HO And PC For Emergency Calls . . . . . . . . . . . . . . . . . . . .
DFCA Channel Allocation Method . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disable External DR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disable Internal HO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL PC 8PSK BEP Target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL PC C/I Target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL High Priority SSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL Low Priority SSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL Normal Priority SSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DLDC offset for PCU2-E selection . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTM Fragmentation Penalty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTRX Power Down Supervision Period . . . . . . . . . . . . . . . . . . . . . . .
EGPRS Inactivity Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Answer To Paging Call On FACCH . . . . . . . . . . . . . . . . . . . .
Enable Call Re-Establishment On FACCH . . . . . . . . . . . . . . . . . . . . .
Enable Emergency Call On FACCH . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Ordinary Calls On FACCH . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS Supervision Stopping Time Hour . . . . . . . . . . . . . . . . . . . . . . . .
BTS Supervision Stopping Time Minute . . . . . . . . . . . . . . . . . . . . . . .
Events Per Hour For EGPRS Inactivity Alarm . . . . . . . . . . . . . . . . . .
Expected BSC-BSC Interface Delay . . . . . . . . . . . . . . . . . . . . . . . . . .
FEP In PC HO Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS Forced Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forced Release Priority Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . .
Free TSL For CS Downgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Free TSLs For CS Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPRS Territory Update Guard Time . . . . . . . . . . . . . . . . . . . . . . . . . .
GSM Macrocell Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GSM Microcell Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HO Preference Order Interference DL . . . . . . . . . . . . . . . . . . . . . . . .
HO Preference Order Interference UL . . . . . . . . . . . . . . . . . . . . . . . .
IMSI Based Handover GSM Cells Anonymous MS . . . . . . . . . . . . . .
IMSI Based Handover WCDMA Cells Anonymous MS . . . . . . . . . . .
Initial AMR Channel Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initial AMR Codec Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
414
416
419
421
422
423
424
426
427
429
430
431
432
433
435
436
437
438
439
440
441
442
443
445
446
448
449
450
451
452
453
454
455
456
457
458
460
461
462
463
464
465
466
467
468
469
471
37
BSS Radio Network Parameter Dictionary
Table 328
Table 329
Table 330
Table 331
Table 332
Table 333
Table 334
Table 335
Table 336
Table 337
Table 338
Table 339
Table 340
Table 341
Table 342
Table 343
Table 344
Table 345
Table 346
Table 347
Table 348
Table 349
Table 350
Table 351
Table 352
Table 353
Table 354
Table 355
Table 356
Table 357
Table 358
Table 359
Table 360
Table 361
Table 362
Table 363
Table 364
Table 365
Table 366
Table 367
Table 368
Table 369
Table 370
Table 371
Table 372
Table 373
Table 374
38
Internal Handover To External . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
Intra Segment SDCCH HO Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
ISHO Preferred For Non-DTM MS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
IBNACC Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
LAPD Load Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
Load Rate For Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478
Local Switching Enabled For Intercepted Calls . . . . . . . . . . . . . . . . . . 479
Lower Limit For FR TCH Resources . . . . . . . . . . . . . . . . . . . . . . . . . . 480
Maximum Mean Holding Time For SDCCHs . . . . . . . . . . . . . . . . . . . . 482
Maximum Mean Holding Time For TCHs . . . . . . . . . . . . . . . . . . . . . . . 483
Maximum Number Of DL TBF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
Maximum Number Of UL TBF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
Maximum TCH Transaction Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
Mean BEP Limit MS Multislot Pwr Prof 0 With 2 UL TSL . . . . . . . . . . 487
Mean BEP Limit MS Multislot Pwr Prof 0 With 3 UL TSL . . . . . . . . . . 488
Mean BEP Limit MS Multislot Pwr Prof 0 With 4 UL TSL . . . . . . . . . . 489
Mean BEP Limit MS Multislot Pwr Prof 1 With 2 UL TSL . . . . . . . . . . 490
Mean BEP Limit MS Multislot Pwr Prof 1 With 3 UL TSL . . . . . . . . . . 491
Mean BEP Limit MS Multislot Pwr Prof 1 With 4 UL TSL . . . . . . . . . . 492
Mean BEP Limit MS Multislot Pwr Prof 2 With 3 UL TSL . . . . . . . . . . 493
Mean BEP Limit MS Multislot Pwr Prof 2 With 4 UL TSL . . . . . . . . . . 495
Meas Period For High TCH Interference Supervision . . . . . . . . . . . . . 496
Meas Period For SDCCH Mean Holding Time Supervision . . . . . . . . . 497
Meas Period For Supervision Of BTS With No Transact . . . . . . . . . . . 498
Meas Period For Supervision Of Channel Failure Rate . . . . . . . . . . . . 499
Measurement Period For Supervision Of Congestion In BTS . . . . . . . 500
Meas Period For TCH Mean Holding Time Supervision . . . . . . . . . . . 501
Minimum Mean Holding Time For TCHs . . . . . . . . . . . . . . . . . . . . . . . 502
MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503
Radio Network MCC 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504
Radio Network MCC 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
Radio Network MCC 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
Radio Network MCC 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
Radio Network MCC 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510
Radio Network MCC 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
Radio Network MCC 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
Radio Network MCC 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
Radio Network MCC 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
Radio Network MCC 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
Radio Network MCC 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
Radio Network MCC 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519
Radio Network MCC 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520
Radio Network MCC 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 522
Radio Network MCC 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523
Radio Network MCC 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524
MNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526
Radio Network MNC 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 375
Table 376
Table 377
Table 378
Table 379
Table 380
Table 381
Table 382
Table 383
Table 384
Table 385
Table 386
Table 387
Table 388
Table 389
Table 390
Table 391
Table 392
Table 393
Table 394
Table 395
Table 396
Table 397
Table 398
Table 399
Table 400
Table 401
Table 402
Table 403
Table 404
Table 405
Table 406
Table 407
Table 408
Table 409
Table 410
Table 411
Table 412
Table 413
Table 414
Table 415
Table 416
Table 417
Table 418
Table 419
Table 420
Table 421
DN9813866
Radio Network MNC 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Network MNC 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MS Distance Behaviour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M-plane Packet Drop Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MC-PPP Assured Forwarding Class 1 . . . . . . . . . . . . . . . . . . . . . . . .
MC-PPP Assured Forwarding Class 2 . . . . . . . . . . . . . . . . . . . . . . . .
MC-PPP Assured Forwarding Class 3 . . . . . . . . . . . . . . . . . . . . . . . .
MC-PPP Assured Forwarding Class 4 . . . . . . . . . . . . . . . . . . . . . . . .
MC-PPP Best Effort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MC-PPP Expedited Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NACC Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nbr measurement period in NC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NCCR Control Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NCCR Idle Mode Reporting Period . . . . . . . . . . . . . . . . . . . . . . . . . . .
NCCR Neighbor Cell Penalty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NCCR Return To Old Cell Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NCCR Target Cell Penalty Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NCCR Transfer Mode Reporting Period . . . . . . . . . . . . . . . . . . . . . . .
NRI List 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NRI List 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CS Null-NRI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Number Of Ignored Transcoder Failures . . . . . . . . . . . . . . . . . . . . . .
Number Of Preferred Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Penalty Trigger Measurement Period . . . . . . . . . . . . . . . . . . . . . . . . .
PFC Ack BLER Limit For Transfer Delay 1 . . . . . . . . . . . . . . . . . . . .
PFC Unack BLER Limit For SDU Error Ratio 1 . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
528
530
532
534
536
538
540
541
543
544
546
547
549
550
552
553
555
556
557
558
560
561
562
563
564
565
566
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
584
584
586
587
588
39
BSS Radio Network Parameter Dictionary
Table 422
Table 423
Table 424
Table 425
Table 426
Table 427
Table 428
Table 429
Table 430
Table 431
Table 432
Table 433
Table 434
Table 435
Table 436
Table 437
Table 438
Table 439
Table 440
Table 441
Table 442
Table 443
Table 444
Table 445
Table 446
Table 447
Table 448
Table 449
Table 450
Table 451
Table 452
Table 453
Table 454
Table 455
Table 456
Table 457
Table 458
Table 459
Table 460
Table 461
Table 462
Table 463
Table 464
Table 465
Table 466
Table 467
Table 468
40
Pre-Emption Usage In Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589
Precise Paging Enabled For Repagings . . . . . . . . . . . . . . . . . . . . . . . 590
Precise Paging Expanding Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 591
Precise Paging MSC Repaging Delay . . . . . . . . . . . . . . . . . . . . . . . . . 592
Precise Paging Location Records Living Time . . . . . . . . . . . . . . . . . . 593
Precise Paging TMSI Optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . 594
Priority Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595
PSE Overload Alarm Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595
PSE PCU Selection Algorithm Threshold . . . . . . . . . . . . . . . . . . . . . . 596
Public Served Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 597
Packet Loss Timer Duration Start Reaction . . . . . . . . . . . . . . . . . . . . . 598
Packet Loss Timer Duration Stop Reaction . . . . . . . . . . . . . . . . . . . . . 600
PS Packet Drop Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601
PS UDP-MUX Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602
QC NCCR Action Trigger Threshold . . . . . . . . . . . . . . . . . . . . . . . . . 604
QC Reallocation Action Trigger Threshold . . . . . . . . . . . . . . . . . . . . . 605
RNC to SPC mapping info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 606
RNC ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607
RNW Configuration Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 608
RNW Fallback Configuration Identification . . . . . . . . . . . . . . . . . . . . . 609
RNW Plan Configuration Identification . . . . . . . . . . . . . . . . . . . . . . . . . 610
RNW Plan Database State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611
RX Antenna Supervision Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 613
RX Level Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614
RX Level Based TCH Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615
RX Quality Limit MS Multislot Pwr Prof 0 With 2 UL TSL . . . . . . . . . . 616
RX Quality Limit MS Multislot Pwr Prof 0 With 3 UL TSL . . . . . . . . . . 617
RX Quality Limit MS Multislot Pwr Prof 0 With 4 UL TSL . . . . . . . . . . 618
RX Quality Limit MS Multislot Pwr Prof 1 With 2 UL TSL . . . . . . . . . . 619
RX Quality Limit MS Multislot Pwr Prof 1 With 3 UL TSL . . . . . . . . . . 621
RX Quality Limit MS Multislot Pwr Prof 1 With 4 UL TSL . . . . . . . . . . 622
RX Quality Limit MS Multislot Pwr Prof 2 With 3 UL TSL . . . . . . . . . . 623
RX Quality Limit MS Multislot Pwr Prof 2 With 4 UL TSL . . . . . . . . . . 624
SACCH Repeat Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625
SAIC DL C/I Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 626
Service Area Penalty Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 629
Signalling Point Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630
Signaling Point Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631
Signaling Point Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632
Slow AMR LA Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633
Soft Blocking C/I 14.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 634
Soft Blocking C/I AMR FR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 635
Soft Blocking C/I AMR HR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637
Soft Blocking C/I FR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638
DFCA Soft Blocking C/I GPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639
Soft Blocking C/I HR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640
Soft Blocking C/I OSC DFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 641
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 469
Table 470
Table 471
Table 472
Table 473
Table 474
Table 475
Table 476
Table 477
Table 478
Table 479
Table 480
Table 481
Table 482
Table 483
Table 484
Table 485
Table 486
Table 487
Table 488
Table 489
Table 490
Table 491
Table 492
Table 493
Table 494
Table 495
Table 496
Table 497
Table 498
Table 499
Table 500
Table 501
Table 502
Table 503
Table 504
Table 505
Table 506
Table 507
Table 508
Table 509
Table 510
Table 511
Table 512
Table 513
Table 514
Table 515
DN9813866
Soft Blocking C/I OSC DHR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DFCA Soft Blocking C/I SDCCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Blocking C/N 14.4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Blocking C/N AMR FR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Blocking C/N AMR HR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Blocking C/N FR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Blocking C/N HR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS Supervision Starting Time Hour . . . . . . . . . . . . . . . . . . . . . . . . .
BTS Supervision Starting Time Minute . . . . . . . . . . . . . . . . . . . . . . . .
Subscriber Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supervision Period Length for EGPRS Inactivity Alarm . . . . . . . . . . .
SSM Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Site support Traffic DSCP Mapping . . . . . . . . . . . . . . . . . . . . . . . . . .
TCH In Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCH Transaction Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold For High TCH Interference Level . . . . . . . . . . . . . . . . . . . .
Time Limit WPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time Limit WPS Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRHO Guard Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Triggering Threshold For Service Area Penalty . . . . . . . . . . . . . . . . .
TS AF1 WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS AF2 WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS AF3 WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS AF4 WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TS BE WFQ Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL Priority 1 SSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL Priority 2 SSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL Priority 3 SSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UL Priority 4 SSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Limit For FR TCH Resources . . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Limit Of MS Speed Class 1 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Limit Of MS Speed Class 2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable DL Step Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN Priority AF1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN Priority AF2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN Priority AF3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN Priority AF4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN Priority BE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN Priority EF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WCDMA FDD NCCR Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WCDMA FDD NCCR Preferred . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WPS Preference Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WPS Priority Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adaptive LA Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMR FR Codec Mode Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMR FR DL Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
642
643
644
645
646
647
648
649
650
651
652
653
655
656
658
659
660
661
662
663
664
666
667
668
670
671
672
673
674
675
676
677
678
679
680
682
683
684
686
687
688
690
691
693
694
695
696
41
BSS Radio Network Parameter Dictionary
Table 516
Table 517
Table 518
Table 519
Table 520
Table 521
Table 522
Table 523
Table 524
Table 525
Table 526
Table 527
Table 528
Table 529
Table 530
Table 531
Table 532
Table 533
Table 534
Table 535
Table 536
Table 537
Table 538
Table 539
Table 540
Table 541
Table 542
Table 543
Table 544
Table 545
Table 546
Table 547
Table 548
Table 549
Table 550
Table 551
Table 552
Table 553
Table 554
Table 555
Table 556
Table 557
Table 558
Table 559
Table 560
Table 561
Table 562
42
AMR FR DL Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698
AMR FR DL Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700
AMR FR Hysteresis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702
AMR FR Hysteresis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 704
AMR FR Hysteresis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706
AMR FR Initial Codec Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 709
AMR FR Start Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710
AMR FR UL Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712
AMR FR UL Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 714
AMR FR UL Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716
AMR HR Codec Mode Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 718
AMR HR DL Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 719
AMR HR DL Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720
AMR HR DL Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723
AMR HR Hysteresis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724
AMR HR Hysteresis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727
AMR HR Hysteresis 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 729
AMR HR Initial Codec Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 732
AMR HR Start Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733
AMR HR UL Radio Link Timeout Increase Step . . . . . . . . . . . . . . . . . 735
AMR HR UL Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 736
AMR HR UL Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738
AMR HR UL Threshold 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 739
AMR UL Radio Link Timeout Increase Step . . . . . . . . . . . . . . . . . . . . 742
AMR-WB Codec Mode Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743
AMR-WB FR Threshold 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 744
AMR-WB FR Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745
AMR-WB FR Hysteresis 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 747
AMR-WB FR Hysteresis 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748
Antenna Hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750
BCCH TRX Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 751
Interference Averaging Boundary 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . 752
Interference Averaging Boundary 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 753
Interference Averaging Boundary 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . 754
Interference Averaging Boundary 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . 755
Interference Averaging Boundary 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . 756
Interference Averaging Boundary 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . 757
BSC-BSC Interface Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 758
BTS Downlink Throughput Factor For CS1-CS4 . . . . . . . . . . . . . . . . . 759
BTS Downlink Throughput Factor For MCS1-MCS9 . . . . . . . . . . . . . . 760
BTS Hopping Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 761
BTS ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 763
BTS Load In SEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 764
BTS Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 765
BTS TCH Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 766
BTS Uplink Throughput Factor For CS1-CS4 . . . . . . . . . . . . . . . . . . . 767
BTS Uplink Throughput Factor For MCS1-MCS4 . . . . . . . . . . . . . . . . 768
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 563
Table 564
Table 565
Table 566
Table 567
Table 568
Table 569
Table 570
Table 571
Table 572
Table 573
Table 574
Table 575
Table 576
Table 577
Table 578
Table 579
Table 580
Table 581
Table 582
Table 583
Table 584
Table 585
Table 586
Table 587
Table 588
Table 589
Table 590
Table 591
Table 592
Table 593
Table 594
Table 595
Table 596
Table 597
Table 598
Table 599
Table 600
Table 601
Table 602
Table 603
Table 604
Table 605
Table 606
Table 607
Table 608
Table 609
DN9813866
BTS Uplink Throughput Factor For MCS1-MCS9 . . . . . . . . . . . . . . . .
BCSU ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C/N Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Composited Multi Site Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cell Number In BTS HW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coding Schemes CS3 And CS4 Enabled . . . . . . . . . . . . . . . . . . . . . .
Dedicated GPRS Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Default GPRS Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DFCA Mobile Allocation Frequency Lists . . . . . . . . . . . . . . . . . . . . . .
DFCA Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DFCA Unsynchronized Mode MA Frequency List . . . . . . . . . . . . . . .
DL Coding Scheme In Acknowledged Mode . . . . . . . . . . . . . . . . . . .
DL Coding Scheme In Ext Area Acknowledged Mode . . . . . . . . . . . .
DL Coding Scheme In Ext Area Unacknowledged Mode . . . . . . . . . .
DL Coding Scheme In Unacknowledged Mode . . . . . . . . . . . . . . . . .
DL Noise Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DLDC Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EGPRS Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EGPRS Inactivity Alarm End Time Hour . . . . . . . . . . . . . . . . . . . . . . .
EGPRS Inactivity Alarm End Time Minute . . . . . . . . . . . . . . . . . . . . .
EGPRS Inactivity Alarm Start Time Hour . . . . . . . . . . . . . . . . . . . . . .
EGPRS Inactivity Alarm Start Time Minute . . . . . . . . . . . . . . . . . . . . .
EGPRS Inactivity Alarm Weekdays . . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Cell GPRS/EDGE Enabled . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Cell Location Keep Period . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Paging Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fast Return to TD-SCDMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forced AMR HR Mode C/I Threshold . . . . . . . . . . . . . . . . . . . . . . . . .
Forced HR Mode C/I Averaging Period . . . . . . . . . . . . . . . . . . . . . . .
Forced HR Mode C/I Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forced HR Mode Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frequency Band In Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPRS Non BCCH Layer Rxlev Lower Limit . . . . . . . . . . . . . . . . . . . .
GPRS Non BCCH Layer Rxlev Upper Limit . . . . . . . . . . . . . . . . . . . .
Hopping Sequence Number 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hopping Sequence Number 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSCSD Cell Load Lower Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSCSD Cell Load Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSCSD Regular Cell Load Upper Limit . . . . . . . . . . . . . . . . . . . . . . .
HSCSD TCH Capacity Minimum . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Immediate SDCCH HO Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initial MCS For Ext Area Acknowledged Mode . . . . . . . . . . . . . . . . . .
Initial MCS For Ext Area Unacknowledged Mode . . . . . . . . . . . . . . . .
Limit for Triggering OSC DFR Multiplexing . . . . . . . . . . . . . . . . . . . . .
Limit for Triggering OSC DHR Multiplexing . . . . . . . . . . . . . . . . . . . .
MAIO Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAIO Step . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
769
770
771
772
773
775
776
777
779
780
781
782
784
786
787
789
790
791
792
793
794
795
796
798
800
801
802
804
805
806
807
808
809
811
812
813
814
815
816
817
818
820
821
822
823
826
827
43
BSS Radio Network Parameter Dictionary
Table 610
Table 611
Table 612
Table 613
Table 614
Table 615
Table 616
Table 617
Table 618
Table 619
Table 620
Table 621
Table 622
Table 623
Table 624
Table 625
Table 626
Table 627
Table 628
Table 629
Table 630
Table 631
Table 632
Table 633
Table 634
Table 635
Table 636
Table 637
Table 638
Table 639
Table 640
Table 641
Table 642
Table 643
Table 644
Table 645
Table 646
Table 647
Table 648
Table 649
Table 650
Table 651
Table 652
Table 653
Table 654
Table 655
Table 656
44
Max GPRS Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 828
Used MAL ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 829
MS Tx Pwr Min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 830
Non BCCH Layer Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 832
Non BCCH Layer Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 833
PCU Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 834
PCU Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 835
PCU Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 836
PCU PSW TBF Density Target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 837
PCU PSW TBF Downgrade Threshold . . . . . . . . . . . . . . . . . . . . . . . . 838
PCU PSW TBF Upgrade Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . 840
PCU Up To Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 841
Radius Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 842
RX diversity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 844
Rx Signal Level Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 845
RACH Threshold of Composite Cell Node . . . . . . . . . . . . . . . . . . . . . . 847
Sector ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 848
STIRC Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 849
Super Radius Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850
TD SCDMA NCCR enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 851
Transport Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 852
Tx Signal Level Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853
UL Coding Scheme In Acknowledged Mode . . . . . . . . . . . . . . . . . . . . 855
UL Coding Scheme In Ext Area Acknowledged Mode . . . . . . . . . . . . . 856
UL Coding Scheme In Ext Area Unacknowledged Mode . . . . . . . . . . 858
UL Coding Scheme In Unacknowledged Mode . . . . . . . . . . . . . . . . . . 860
UL Noise Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 861
UL Radio Link Timeout Increase Step . . . . . . . . . . . . . . . . . . . . . . . . . 862
Underlay BTS Hopping Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 863
Underlay Hopping Sequence Number . . . . . . . . . . . . . . . . . . . . . . . . . 864
Underlay MAIO Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
Underlay MAIO Step . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 867
Underlay MAL ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 868
8k TRAU for DFR Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 869
Adjacency On Other Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 871
Allow IMSI Attach Detach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872
AMH Lower Load Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873
AMH Max Load Of Target Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 874
AMH Upper Load Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875
AMR HR Radio Link Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 876
AMR Lower Limit For SEG FR Resources . . . . . . . . . . . . . . . . . . . . . . 877
AMR Radio Link Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 879
AMR Upper Limit For SEG FR Resources . . . . . . . . . . . . . . . . . . . . . . 880
Apply Repeated FACCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881
Averaging Period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 882
BCCH Allocation Usage For Active MS . . . . . . . . . . . . . . . . . . . . . . . . 883
BSIC BCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 884
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 657
Table 658
Table 659
Table 660
Table 661
Table 662
Table 663
Table 664
Table 665
Table 666
Table 667
Table 668
Table 669
Table 670
Table 671
Table 672
Table 673
Table 674
Table 675
Table 676
Table 677
Table 678
Table 679
Table 680
Table 681
Table 682
Table 683
Table 684
Table 685
Table 686
Table 687
Table 688
Table 689
Table 690
Table 691
Table 692
Table 693
Table 694
Table 695
Table 696
Table 697
Table 698
Table 699
Table 700
Table 701
Table 702
Table 703
DN9813866
BTS Load Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BTS Measure Average . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCSU ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CA List Per BTS Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Reestablishment Allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carrier Unit Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cell Bar Qualify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cell Barred . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cell Load For Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cell Reselect Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cell Reselect Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cell Reselection Parameter Index . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDR Cell Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coding Scheme Hop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coding Scheme No Hop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct GPRS Access BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Directed Retry Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Directed Retry Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL adaption probability threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL BLER Crosspoint For CS Selection Hop . . . . . . . . . . . . . . . . . . . .
DL BLER Crosspoint For CS Selection No Hop . . . . . . . . . . . . . . . . .
DTM Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2G TRX Power Down Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTRX Power Up Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Early Sending Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EGPRS Link Adaptation Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency Call Restricted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Temporary Overpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Cell GPRS/EDGE Enabled . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Cell Location Keep Period . . . . . . . . . . . . . . . . . . . . . . . . .
Extended BCCH Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FACCH Busy Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FDD Cell Reselect Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
gprsDlPcEnabled (GPRS DL PC Enabled) . . . . . . . . . . . . . . . . . . . . .
GPRS Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPRS MS Txpwr Max CCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPRS MS Txpwr Max CCH 1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPRS Rxlev Access Min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GPRS Threshold To Search UTRAN Cells . . . . . . . . . . . . . . . . . . . . .
HCS Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSCSD Downgrade Guard Time . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSCSD Minimum Exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSCSD Upgrade Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HSCSD Upgrade Guard Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle State BCCH Allocation List (BAL) ID . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
886
887
888
889
890
891
893
894
895
896
897
898
899
900
902
903
904
905
906
907
908
909
910
911
913
914
915
916
917
918
920
921
923
924
925
926
927
928
929
931
932
934
935
936
937
938
939
45
BSS Radio Network Parameter Dictionary
Table 704
Table 705
Table 706
Table 707
Table 708
Table 709
Table 710
Table 711
Table 712
Table 713
Table 714
Table 715
Table 716
Table 717
Table 718
Table 719
Table 720
Table 721
Table 722
Table 723
Table 724
Table 725
Table 726
Table 727
Table 728
Table 729
Table 730
Table 731
Table 732
Table 733
Table 734
Table 735
Table 736
Table 737
Table 738
Table 739
Table 740
Table 741
Table 742
Table 743
Table 744
Table 745
Table 746
Table 747
Table 748
Table 749
Table 750
46
IMSI Based Handover GSM Enabled . . . . . . . . . . . . . . . . . . . . . . . . . 941
IMSI Based Handover WCDMA Enabled . . . . . . . . . . . . . . . . . . . . . . . 942
Initial MCS For Acknowledged Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 944
Initial MCS For Ext Area Acknowledged Mode . . . . . . . . . . . . . . . . . . 945
Initial MCS For Ext Area Unacknowledged Mode . . . . . . . . . . . . . . . . 946
Initial MCS For Unacknowledged Mode . . . . . . . . . . . . . . . . . . . . . . . . 947
Intelligent Directed Retry Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 948
Interval Measurement Report Sending . . . . . . . . . . . . . . . . . . . . . . . . 949
Limit For Free TCHs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950
LAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 951
Lower Limit For FR TCH Resources . . . . . . . . . . . . . . . . . . . . . . . . . . 952
Max Number Of Repetition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953
Max Number Of Retransmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954
Max Queue Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 955
Max Time Limit Directed Retry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 956
Maximum BLER In Acknowledged Mode . . . . . . . . . . . . . . . . . . . . . . . 957
Maximum BLER In Unacknowledged Mode . . . . . . . . . . . . . . . . . . . . 958
Mean BEP Offset 8PSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 959
Mean BEP Offset GMSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 961
Measurement BCCH Allocation List . . . . . . . . . . . . . . . . . . . . . . . . . . . 962
Min Time Limit Directed Retry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 963
Minimum FDD Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 964
Minimum Fdd Threshold Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965
Minimum RSCP Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967
MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 968
MNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969
MSC HO Control Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 970
MS Max Distance In Call Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 972
MS Priority Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 973
MS Tx Pwr Max CCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 974
MS Tx Pwr Max CCH 1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 975
MS Tx Pwr Max GSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977
MS Tx Pwr Max GSM 1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 978
Multiband Cell Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 979
BSIC NCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 980
NSEI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 981
New Establishment Causes Support . . . . . . . . . . . . . . . . . . . . . . . . . . 982
Not Allowed Access Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983
Number Of Blocks For Access Grant Msg . . . . . . . . . . . . . . . . . . . . . . 985
Number Of Multiframes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986
Number Of Slots Spread Trans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 987
Number Of TCH Reserved For Priority Subscribers Only . . . . . . . . . . 989
Packet Service Entity Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 990
Penalty Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 991
PLMN Permitted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 992
Power Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 993
Precise Paging Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 994
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 751
Table 752
Table 753
Table 754
Table 755
Table 756
Table 757
Table 758
Table 759
Table 760
Table 761
Table 762
Table 763
Table 764
Table 765
Table 766
Table 767
Table 768
Table 769
Table 770
Table 771
Table 772
Table 773
Table 774
Table 775
Table 776
Table 777
Table 778
Table 779
Table 780
Table 781
Table 782
Table 783
Table 784
Table 785
Table 786
Table 787
Table 788
Table 789
Table 790
Table 791
Table 792
Table 793
Table 794
Table 795
Table 796
Table 797
DN9813866
Prefer BCCH Frequency GPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995
Priority Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 997
PCU Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 998
Queue Priority Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 999
Queueing Priority Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000
Queueing Priority Non-Urgent Handover . . . . . . . . . . . . . . . . . . . . . 1002
Queueing Priority Urgent Handover . . . . . . . . . . . . . . . . . . . . . . . . . 1003
RA Reselect Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1004
RACH Busy Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005
Radio Link Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006
Repeated FACCH In DL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007
Repeated FACCH In UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009
Repeated SACCH In DL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010
Repeated SACCH In UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1012
Repeated SACCH RX Lev Threshold DL . . . . . . . . . . . . . . . . . . . . . 1013
Repeated SACCH RX Lev Threshold UL . . . . . . . . . . . . . . . . . . . . . 1014
Reservation Method Used In Trunk Reservation . . . . . . . . . . . . . . . 1016
Restricted Use Of Priority Channels In Incoming HO . . . . . . . . . . . . 1017
RAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1018
Rxlev Access Min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1019
Scale Ord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1020
SDCCH Measurement Report Sending . . . . . . . . . . . . . . . . . . . . . . 1021
Segment ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1022
Segment Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1024
SMS CB Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1025
Table Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1026
TCH Rate Intra-Cell Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027
Temporary Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1029
Threshold To Search UTRAN Cells . . . . . . . . . . . . . . . . . . . . . . . . . 1030
Time Limit Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1032
Time Limit Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1033
Timer For Periodic MS Location Updating . . . . . . . . . . . . . . . . . . . . 1034
Traffic Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035
TRHO Guard Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1036
Trunk Reservation Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037
TRX Priority In TCH Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1038
TX Diversity Time Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1039
UL Adaption Probability Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . 1041
UL BLER Crosspoint For CS Selection Hop . . . . . . . . . . . . . . . . . . . 1042
UL BLER Crosspoint For CS Selection No Hop . . . . . . . . . . . . . . . . 1043
Upper Limit For FR TCH Resources . . . . . . . . . . . . . . . . . . . . . . . . 1044
Merged PGSM and EGSM Enabled . . . . . . . . . . . . . . . . . . . . . . . . . 1045
WCDMA Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1046
GPRS Capacity Throughput Factor . . . . . . . . . . . . . . . . . . . . . . . . . 1047
Lower DL RX Lev Threshold For BCCH TRX Pref For TCH . . . . . . . 1048
Master BTS ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050
Upper DL RX Lev Threshold For BCCH TRX Pref For TCH . . . . . . . 1051
Id:0900d8058089b098
Confidential
47
BSS Radio Network Parameter Dictionary
Table 798
Table 799
Table 800
Table 801
Table 802
Table 803
Table 804
Table 805
Table 806
Table 807
Table 808
Table 809
Table 810
Table 811
Table 812
Table 813
Table 814
Table 815
Table 816
Table 817
Table 818
Table 819
Table 820
Table 821
Table 822
Table 823
Table 824
Table 825
Table 826
Table 827
Table 828
Table 829
Table 830
Table 831
Table 832
Table 833
Table 834
Table 835
Table 836
Table 837
Table 838
Table 839
Table 840
Table 841
Table 842
Table 843
Table 844
48
BCF Abis IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1053
BCF Timeslot Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1054
Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1055
CSDAP ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1056
Pool Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1057
BCSU ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1059
Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1060
Packet Service Entity Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1061
PCU Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1063
DAP ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1064
Pool Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1065
Connected PCUs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067
BCSU ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1068
ETP Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069
ETP Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1071
ETME Hardware Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1072
PCU index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073
SyncE Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074
Used ETP ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1076
NCCR Number Of Zero Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1078
NCCR Other PCU Cell Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1079
NCCR Rxlev Idle Mode Window Size . . . . . . . . . . . . . . . . . . . . . . . . 1080
NCCR Rxlev Transfer Mode Window Size . . . . . . . . . . . . . . . . . . . . 1081
Quality Control EGPRS DL RLC Ack Throughput Threshold . . . . . . 1082
Quality Control EGPRS UL RLC Ack Throughput Threshold . . . . . . 1083
Quality Control GPRS DL RLC Ack Throughput Threshold . . . . . . . . 1084
Quality Control GPRS UL RLC Ack Throughput Threshold . . . . . . . . 1085
850 Reporting Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1087
850 Reporting Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1088
900 Reporting Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1089
900 Reporting Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1090
1800 Reporting Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1091
1800 Reporting Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1092
1900 Reporting Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1093
1900 Reporting Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1094
Adjacent Cell Averaging Window Size . . . . . . . . . . . . . . . . . . . . . . . . 1096
Adjacent WCDMA RAN Cell Averaging Window Size . . . . . . . . . . . . 1096
Advanced Compression HO For AMR . . . . . . . . . . . . . . . . . . . . . . . . 1097
All Adjacent Cells Averaged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1099
All Adjacent WCDMA RAN Cells Averaged . . . . . . . . . . . . . . . . . . . . 1100
All Interfering Cells Averaged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1101
AMH Traffic Control IUO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1102
AMH Traffic Control MCN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1103
AMH TRHO PBGT Margin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104
C/I Estimation Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1105
Count Of Successive Rapid Field Drop Thresholds . . . . . . . . . . . . . . 1106
Deep Dropping EDGE Monitoring Window . . . . . . . . . . . . . . . . . . . . 1107
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 845
Table 846
Table 847
Table 848
Table 849
Table 850
Table 851
Table 852
Table 853
Table 854
Table 855
Table 856
Table 857
Table 858
Table 859
Table 860
Table 861
Table 862
Table 863
Table 864
Table 865
Table 866
Table 867
Table 868
Table 869
Table 870
Table 871
Table 872
Table 873
Table 874
Table 875
Table 876
Table 877
Table 878
Table 879
Table 880
Table 881
Table 882
Table 883
Table 884
Table 885
Table 886
Table 887
Table 888
Table 889
Table 890
Table 891
DN9813866
Enable Enhanced Rapid Field Drop . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Fast Averaging Call Setup . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Fast Averaging HO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Fast Averaging PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Inter FRT Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Intracell Handover Interference DL . . . . . . . . . . . . . . . . . . . .
Enable Intracell Handover Interference UL . . . . . . . . . . . . . . . . . . . .
Enable MS Distance Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Power Budget Handover . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable SDCCH Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Hierachical Cell HO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable TCH Assignment Super IUO . . . . . . . . . . . . . . . . . . . . . . . . .
Enable Umbrella Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enhanced Rapid Field Drop Duration . . . . . . . . . . . . . . . . . . . . . . . .
Reporting Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reporting Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fdd Reporting Threshold 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GSM PLMN Priorisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handover Period Power Budget . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handover Period Umbrella . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inter-System Direct Access Enabled . . . . . . . . . . . . . . . . . . . . . . . .
Interfering Cell Averaging Window Size . . . . . . . . . . . . . . . . . . . . . .
Interfering Cell Number Of Zero Results . . . . . . . . . . . . . . . . . . . . . .
Intra HO Lower Rx Level Limit AMR HR . . . . . . . . . . . . . . . . . . . . . .
Intra HO Lower Rx Quality Limit AMR . . . . . . . . . . . . . . . . . . . . . . .
Intra HO Threshold Rx Qual AMR FR . . . . . . . . . . . . . . . . . . . . . . . .
Intra HO Threshold Rx Qual AMR FR to DFR . . . . . . . . . . . . . . . . .
AMR Handover HR Intra Threshold Rx Qual . . . . . . . . . . . . . . . . . .
Intra HO Upper Rx Level Limit AMR HR . . . . . . . . . . . . . . . . . . . . . .
Invalid BSIC Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Level Downlink Weighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Level Downlink Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Level Uplink Weighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Level Uplink Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lower C/I Limit For Band 1-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lower Speed Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Min Int Between HO Req . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Min Int Between Unsucc HO Attempt . . . . . . . . . . . . . . . . . . . . . . . .
Min Interval Between IUO HO Req BQ . . . . . . . . . . . . . . . . . . . . . . .
Min Interval Between Unsucc ISHO Attempt . . . . . . . . . . . . . . . . . .
Min Interval Between Unsucc IUO HO . . . . . . . . . . . . . . . . . . . . . . .
Min Traffic Load For Speech Call . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minimum BSIC Decode Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modified Averaging Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modified Number Of Zero Results . . . . . . . . . . . . . . . . . . . . . . . . . .
MS Distance Averaging Window Size . . . . . . . . . . . . . . . . . . . . . . . .
MS Distance HO Threshold Ext Cell Max . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
1107
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1127
1127
1128
1129
1130
1131
1132
1134
1135
1136
1137
1138
1139
1141
1141
1143
1143
1145
1146
1147
1148
1149
1150
1151
1152
1152
1153
1154
1155
49
BSS Radio Network Parameter Dictionary
Table 892
Table 893
Table 894
Table 895
Table 896
Table 897
Table 898
Table 899
Table 900
Table 901
Table 902
Table 903
Table 904
Table 905
Table 906
Table 907
Table 908
Table 909
Table 910
Table 911
Table 912
Table 913
Table 914
Table 915
Table 916
Table 917
Table 918
Table 919
Table 920
Table 921
Table 922
Table 923
Table 924
Table 925
Table 926
Table 927
Table 928
Table 929
Table 930
Table 931
Table 932
Table 933
Table 934
Table 935
Table 936
Table 937
Table 938
50
MS Distance HO Threshold Ext Cell Min . . . . . . . . . . . . . . . . . . . . . . 1157
MS Distance HO Threshold Super Ext Cell Max . . . . . . . . . . . . . . . . 1158
MS Distance HO Threshold Super Ext Cell Min . . . . . . . . . . . . . . . . 1159
MS Distance Threshold Param MS Max Range . . . . . . . . . . . . . . . . 1161
MS Distance Threshold Param Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . 1161
MS Distance Threshold Param Px . . . . . . . . . . . . . . . . . . . . . . . . . . . 1162
MS Speed Averaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1163
MS Speed Detection State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1164
MS Speed Threshold Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1165
MS Speed Threshold Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1166
Non BCCH Layer Access Threshold . . . . . . . . . . . . . . . . . . . . . . . . . 1167
Non BCCH Layer Exit Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1169
Non BCCH Layer Exit Threshold Nx . . . . . . . . . . . . . . . . . . . . . . . . . 1170
Non BCCH Layer Exit Threshold Px . . . . . . . . . . . . . . . . . . . . . . . . . 1171
Number Of Measured FDD Cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1172
Number Of WCDMA RAN Zero Results . . . . . . . . . . . . . . . . . . . . . . 1173
Number Of Zero Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1174
OSC Demultiplexing Ul Rx Level Margin . . . . . . . . . . . . . . . . . . . . . . 1174
OSC DFR Demultiplexing Rx Quality Threshold . . . . . . . . . . . . . . . . 1176
OSC DFR Demultiplexing UL Rx Level Margin . . . . . . . . . . . . . . . . . 1177
OSC DHR Demultiplexing Rx Quality Threshold . . . . . . . . . . . . . . . . 1178
OSC DFR Multiplexing Rx Quality Threshold . . . . . . . . . . . . . . . . . . 1179
OSC DFR Multiplexing UL Rx Level Threshold . . . . . . . . . . . . . . . . . 1181
OSC DFR Multiplexing UL Rx Level window . . . . . . . . . . . . . . . . . . . 1182
OSC DHR Demultiplexing Ul Rx Level Margin . . . . . . . . . . . . . . . . . 1183
OSC DHR Multiplexing Rx Quality Threshold . . . . . . . . . . . . . . . . . . 1184
OSC DHR Multiplexing Ul Rx Level Threshold . . . . . . . . . . . . . . . . . 1186
OSC DHR Multiplexing Ul Rx Level Window . . . . . . . . . . . . . . . . . . . 1187
OSC Multiplexing Ul Rx Level Threshold . . . . . . . . . . . . . . . . . . . . . . 1188
OSC Multiplexing Ul Rx Level Window . . . . . . . . . . . . . . . . . . . . . . . 1189
Priority Adjustment Step For Band 1-7 . . . . . . . . . . . . . . . . . . . . . . . 1190
Quality Downlink Weighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1191
Quality Downlink Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1192
Quality Uplink Weighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1193
Quality Uplink Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195
Reporting Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195
Serving Band Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1197
Super Radius Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1198
Super Reuse Bad C/I Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1199
Super Reuse Bad C/I Threshold AMR FR . . . . . . . . . . . . . . . . . . . . . 1200
Super Reuse Bad C/I Threshold AMR HR . . . . . . . . . . . . . . . . . . . . . 1201
Super Reuse Bad C/I Threshold Nx . . . . . . . . . . . . . . . . . . . . . . . . . . 1202
Super Reuse Bad C/I Threshold Px . . . . . . . . . . . . . . . . . . . . . . . . . . 1203
Super Reuse Bad Threshold Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1204
Super Reuse Bad Threshold Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1205
Super Reuse Bad Threshold Rx Level . . . . . . . . . . . . . . . . . . . . . . . . 1206
Super Reuse Estimation Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1207
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 939
Table 940
Table 941
Table 942
Table 943
Table 944
Table 945
Table 946
Table 947
Table 948
Table 949
Table 950
Table 951
Table 952
Table 953
Table 954
Table 955
Table 956
Table 957
Table 958
Table 959
Table 960
Table 961
Table 962
Table 963
Table 964
Table 965
Table 966
Table 967
Table 968
Table 969
Table 970
Table 971
Table 972
Table 973
Table 974
Table 975
Table 976
Table 977
Table 978
Table 979
Table 980
Table 981
Table 982
Table 983
Table 984
Table 985
DN9813866
Super Reuse Good C/I Threshold . . . . . . . . . . . . . . . . . . . . . . . . . . .
Super Reuse Good C/I Threshold AMR FR . . . . . . . . . . . . . . . . . . .
Super Reuse Good C/I Threshold AMR HR . . . . . . . . . . . . . . . . . . .
Super Reuse Good C/I Threshold Nx . . . . . . . . . . . . . . . . . . . . . . . .
Super Reuse Good C/I Threshold Px . . . . . . . . . . . . . . . . . . . . . . . .
Super Reuse Good Threshold Nx . . . . . . . . . . . . . . . . . . . . . . . . . . .
Super Reuse Good Threshold Px . . . . . . . . . . . . . . . . . . . . . . . . . . .
Super Reuse Good Threshold Rx Level . . . . . . . . . . . . . . . . . . . . . .
Threshold Deep Dropping EDGE . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Deep Dropping EDGE Nx . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Deep Dropping EDGE Px . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Dl Rx Qual AMR HR . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Dl Rx Qual For AMR FR . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Dl Rx Qual DFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold UL Rx Qual DFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold For Multi-RAT MS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Interference Downlink Nx . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Interference Downlink Px . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Interference Downlink Rx Level . . . . . . . . . . . . . . . . . . . .
Threshold Interference Uplink Nx . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Interference Uplink Px . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Interference Uplink Rx Level . . . . . . . . . . . . . . . . . . . . . .
Threshold Level Downlink Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Level Downlink Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Level Downlink Rx Level . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Level Uplink For Rapid Field Drop . . . . . . . . . . . . . . . . . .
Threshold Level Uplink Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Level Uplink Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Level Uplink Rx Level . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Qual Downlink Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Qual Downlink Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Qual Downlink Rx Qual . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Qual Uplink Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Qual Uplink Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Qual Uplink Rx Qual . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Ul Rx Qual AMR FR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Ul Rx Qual AMR HR . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Triggering Ratio For WCDMA RAN Cell Penalty . . . . . . . . . . . . . . .
Threshold Dl Rx Qual DHR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Threshold Ul Rx Qual DHR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Upper Speed Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WCDMA RAN Cell Penalty Time . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDLC Bandwith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDLC Link ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDLC Link Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDLC PCM ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDLC Start TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1223
1224
1225
1226
1227
1228
1229
1230
1230
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1249
1250
1251
1253
1254
1255
1256
1257
51
BSS Radio Network Parameter Dictionary
Table 986
Table 987
Table 988
Table 989
Table 990
Table 991
Table 992
Table 993
Table 994
Table 995
Table 996
Table 997
Table 998
Table 999
Table 1000
Table 1001
Table 1002
Table 1003
Table 1004
Table 1005
Table 1006
Table 1007
Table 1008
Table 1009
Table 1010
Table 1011
Table 1012
Table 1013
Table 1014
Table 1015
Table 1016
Table 1017
Table 1018
Table 1019
Table 1020
Table 1021
Table 1022
Table 1023
Table 1024
Table 1025
Table 1026
Table 1027
Table 1028
Table 1029
Table 1030
Table 1031
Table 1032
52
Location Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259
SPC ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1260
Signaling Point Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1261
Altitude Of Ground Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1263
Antenna Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1264
Antenna Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1265
Antenna Horizontal Half Power Beam Width . . . . . . . . . . . . . . . . . . . 1265
BCCH Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1266
BSIC BCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1268
Cell Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1269
City Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1269
Latitude Degrees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1270
Latitude Fractions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1271
Latitude Minutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1272
Latitude Seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1273
Latitude Sign . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1274
Location Area Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1275
Longitude Degrees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1276
Longitude Fractions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1277
Longitude Minutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1278
Longitude Seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1279
Longitude Sign . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1280
Maximum Radiated Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1281
BSIC NCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1282
Predicted Back Serving Radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1283
Predicted Front Serving Radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1284
BCF ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1286
Frame Number Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1287
LMU FNO 26-Multiplier Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1288
LMU TSL FN Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1289
LMUA ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1290
LMU TSL FN Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1291
TRE ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1292
DFCA MA List Group ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1294
DFCA MA List State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1295
DFCA MA List Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1296
Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1298
MAL ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1299
Type Of Mobile Allocation Frequency List . . . . . . . . . . . . . . . . . . . . . 1300
Local UDP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1302
NSEI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1303
NSE NRI Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1304
NSE Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1305
NSE Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1306
PS NRI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1307
Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1309
Bearer Channel Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1310
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 1033
Table 1034
Table 1035
Table 1036
Table 1037
Table 1038
Table 1039
Table 1040
Table 1041
Table 1042
Table 1043
Table 1044
Table 1045
Table 1046
Table 1047
Table 1048
Table 1049
Table 1050
Table 1051
Table 1052
Table 1053
Table 1054
Table 1055
Table 1056
Table 1057
Table 1058
Table 1059
Table 1060
Table 1061
Table 1062
Table 1063
Table 1064
Table 1065
Table 1066
Table 1067
Table 1068
Table 1069
Table 1070
Table 1071
Table 1072
Table 1073
Table 1074
Table 1075
Table 1076
Table 1077
Table 1078
Table 1079
DN9813866
Bearer Channel Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Committed Information Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Link Connection Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NSVC ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Service Virtual Connection Name . . . . . . . . . . . . . . . . . . . .
Network Service Virtual Link Identifier . . . . . . . . . . . . . . . . . . . . . . .
Network Service Virtual Link Name . . . . . . . . . . . . . . . . . . . . . . . . .
NSE NRI Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pre-configured SGSN IP Endpoint . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Data Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Host Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote IP Address Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Signalling Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote UDP Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abis Interface Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCSU ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packet Service Entity Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCU Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCU Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCU Up To Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plug-in Unit Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCU Object State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ALA Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BCCH TRX TX Pwr Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Binary Representation ALPHA . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Binary Representation TAU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit Error Probability Filter Averaging Period . . . . . . . . . . . . . . . . . . .
BS Tx Pwr Max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BS TX Pwr Max1x00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BS Tx Pwr Min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BS TX Pwr Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Derived HO Power Security Margin . . . . . . . . . . . . . . . . . . . . . . . . .
DL PC Power Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DL PC Window Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Estimated DL Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Mode Signal Strength Filter Period . . . . . . . . . . . . . . . . . . . . . .
Maximum Power Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Max DL Power Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Tx Power Of Composite Cell Node . . . . . . . . . . . . . . . . .
Max UL Power Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Min Int Between ALA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Averaging Lev DL Weighting . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Averaging Lev DL Window Size . . . . . . . . . . . . . . . . . . . . . . . . .
PC Averaging Lev UL Weighting . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Averaging Lev UL Window Size . . . . . . . . . . . . . . . . . . . . . . . . .
PC Averaging Qual DL Weighting . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Averaging Qual DL Window Size . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
1310
1311
1312
1313
1314
1316
1317
1318
1319
1320
1321
1322
1323
1324
1326
1327
1328
1329
1330
1331
1332
1334
1336
1337
1338
1339
1340
1341
1343
1344
1346
1347
1348
1350
1352
1353
1354
1355
1356
1358
1359
1360
1361
1362
1363
1364
1365
53
BSS Radio Network Parameter Dictionary
Table 1080
Table 1081
Table 1082
Table 1083
Table 1084
Table 1085
Table 1086
Table 1087
Table 1088
Table 1089
Table 1090
Table 1091
Table 1092
Table 1093
Table 1094
Table 1095
Table 1096
Table 1097
Table 1098
Table 1099
Table 1100
Table 1101
Table 1102
Table 1103
Table 1104
Table 1105
Table 1106
Table 1107
Table 1108
Table 1109
Table 1110
Table 1111
Table 1112
Table 1113
Table 1114
Table 1115
Table 1116
Table 1117
Table 1118
Table 1119
Table 1120
Table 1121
Table 1122
Table 1123
Table 1124
Table 1125
Table 1126
54
PC Averaging Qual UL Weighting . . . . . . . . . . . . . . . . . . . . . . . . . . . 1366
PC Averaging Qual UL Window Size . . . . . . . . . . . . . . . . . . . . . . . . . 1367
PC Lower Threshold Dl Rx Qual AMR FR . . . . . . . . . . . . . . . . . . . . . 1368
PC Lower Threshold Dl Rx Qual AMR HR . . . . . . . . . . . . . . . . . . . . . 1369
PC Lower Threshold Dl Rx Qual DFR . . . . . . . . . . . . . . . . . . . . . . . . 1370
PC Lower Threshold Ul Rx Qual AMR FR . . . . . . . . . . . . . . . . . . . . . 1372
PC Lower Threshold Ul Rx Qual AMR HR . . . . . . . . . . . . . . . . . . . . . 1373
PC Lower Threshold Ul Rx Qual DFR . . . . . . . . . . . . . . . . . . . . . . . . 1374
PC Lower Thresholds Lev DL Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1375
PC Lower Thresholds Lev DL Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1376
PC Lower Thresholds Lev DL Rx Level . . . . . . . . . . . . . . . . . . . . . . . 1377
PC Lower Thresholds Lev UL Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1378
PC Lower Thresholds Lev UL Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1379
PC Lower Thresholds Lev UL Rx Level . . . . . . . . . . . . . . . . . . . . . . . 1380
PC Lower Thresholds Qual DL Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . 1381
PC Lower Thresholds Qual DL Px . . . . . . . . . . . . . . . . . . . . . . . . . . . 1382
PC Lower Thresholds Qual DL Rx Qual . . . . . . . . . . . . . . . . . . . . . . 1383
PC Lower Thresholds Qual UL Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . 1384
PC Lower Thresholds Qual UL Px . . . . . . . . . . . . . . . . . . . . . . . . . . . 1385
PC Lower Thresholds Qual UL Rx Qual . . . . . . . . . . . . . . . . . . . . . . 1386
PC Lower Thresholds Qual144 Nx . . . . . . . . . . . . . . . . . . . . . . . . . . 1388
PC Lower Thresholds Qual144 Px . . . . . . . . . . . . . . . . . . . . . . . . . . . 1389
PC Lower Thresholds Qual144 Rx Level . . . . . . . . . . . . . . . . . . . . . . 1390
PC Upper Threshold Dl Rx Qual DFR . . . . . . . . . . . . . . . . . . . . . . . . 1392
PC Upper Threshold Dl Rx Qual DHR . . . . . . . . . . . . . . . . . . . . . . . . 1393
PC Upper Threshold Ul Rx Qual DFR . . . . . . . . . . . . . . . . . . . . . . . . 1394
PC Upper Threshold Ul Rx Qual DHR . . . . . . . . . . . . . . . . . . . . . . . . 1395
PC Upper Threshold Dl Rx Qual AMR FR . . . . . . . . . . . . . . . . . . . . . 1397
PC Upper Threshold Dl Rx Qual AMR HR . . . . . . . . . . . . . . . . . . . . . 1398
PC Upper Threshold Ul Rx Qual AMR FR . . . . . . . . . . . . . . . . . . . . . 1399
PC Upper Threshold Ul Rx Qual AMR HR . . . . . . . . . . . . . . . . . . . . . 1400
PC Upper Thresholds Lev DL Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1402
PC Upper Thresholds Lev DL Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1403
PC Upper Thresholds Lev DL Rx Level . . . . . . . . . . . . . . . . . . . . . . . 1404
PC Upper Thresholds Lev UL Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1405
PC Upper Thresholds Lev UL Px . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1406
PC Upper Thresholds Lev UL Rx Level . . . . . . . . . . . . . . . . . . . . . . . 1407
PC Upper Thresholds Qual DL Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . 1408
PC Upper Thresholds Qual DL Px . . . . . . . . . . . . . . . . . . . . . . . . . . . 1409
PC Upper Thresholds Qual DL Rx Qual . . . . . . . . . . . . . . . . . . . . . . 1410
PC Upper Thresholds Qual UL Nx . . . . . . . . . . . . . . . . . . . . . . . . . . . 1411
PC Upper Thresholds Qual UL Px . . . . . . . . . . . . . . . . . . . . . . . . . . . 1412
PC Upper Thresholds Qual UL Rx Qual . . . . . . . . . . . . . . . . . . . . . . 1413
Power Control Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1414
Power CTRL Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1415
Power Decr Limit Band 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1416
Power Decr Limit Band 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1417
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 1127
Table 1128
Table 1129
Table 1130
Table 1131
Table 1132
Table 1133
Table 1134
Table 1135
Table 1136
Table 1137
Table 1138
Table 1139
Table 1140
Table 1141
Table 1142
Table 1143
Table 1144
Table 1145
Table 1146
Table 1147
Table 1148
Table 1149
Table 1150
Table 1151
Table 1152
Table 1153
Table 1154
Table 1155
Table 1156
Table 1157
Table 1158
Table 1159
Table 1160
Table 1161
Table 1162
Table 1163
Table 1164
Table 1165
Table 1166
Table 1167
Table 1168
Table 1169
Table 1170
Table 1171
Table 1172
Table 1173
DN9813866
Power Decr Limit Band 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Decr Qual Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Incr Step Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Limit ALA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Red Step Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC Lower Threshold Dl Rx Qual DHR . . . . . . . . . . . . . . . . . . . . . . .
PC Lower Threshold Ul Rx Qual DHR . . . . . . . . . . . . . . . . . . . . . . .
PC Lower Thresholds Lev DL Rx Level . . . . . . . . . . . . . . . . . . . . . .
PC Lower Thresholds Lev UL Rx Level . . . . . . . . . . . . . . . . . . . . . .
Transfer Mode Signal Strength Filter Period . . . . . . . . . . . . . . . . . . .
PS Null NRI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packet Service Entity Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PSE NRI Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PS SGSN Load Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NSEI List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 0 PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 1 PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 2 PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 3 PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 4 PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 5 PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 6 PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 7 PCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 0 TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 1 TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 2 TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 3 TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 4 TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 5 TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 6 TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 7 TSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 0 Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 1 Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 2 Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 3 Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 4 Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 5 Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 6 Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 7 Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 0 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 1 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 2 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Channel 3 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
1418
1419
1420
1421
1422
1423
1424
1426
1427
1428
1430
1431
1432
1433
1435
1436
1437
1438
1439
1441
1442
1444
1446
1448
1449
1451
1452
1454
1455
1457
1459
1461
1463
1465
1467
1469
1470
1472
1473
1474
1475
1476
1478
1479
1482
1485
1488
55
BSS Radio Network Parameter Dictionary
Table 1174
Table 1175
Table 1176
Table 1177
Table 1178
Table 1179
Table 1180
Table 1181
Table 1182
Table 1183
Table 1184
Table 1185
Table 1186
Table 1187
Table 1188
Table 1189
Table 1190
Table 1191
Table 1192
Table 1193
Table 1194
Table 1195
Table 1196
Table 1197
Table 1198
Table 1199
Table 1200
Table 1201
Table 1202
Table 1203
Table 1204
Table 1205
Table 1206
Table 1207
Table 1208
Table 1209
Table 1210
Table 1211
Table 1212
Table 1213
Table 1214
Table 1215
Table 1216
Table 1217
Table 1218
Table 1219
Table 1220
56
Channel 4 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1491
Channel 5 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1494
Channel 6 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1497
Channel 7 Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500
Ane ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1504
Home MCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1505
Home MNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1506
SG ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1507
Subscriber Group Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1507
WCDMA RAN Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1508
High Response Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1510
LCS Ignore Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1511
Low Response Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1512
PBS Halfrate Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1513
PBS Stop Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1514
TID ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1515
Text String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1516
Decision Threshold Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1518
Random Value Upper Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1519
TRKT ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1520
Administrative State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1521
Autoconfigure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1522
BB Unit Supports EDGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1523
Binary Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1524
Bit Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1525
C/I Estimation Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1527
C/I Estimation Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1528
CI Of Interfering Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1529
Combi Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1529
O&M LAPD Link Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1531
O&M LAPD Link Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1532
LAPD Link Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1533
LAPD Link Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1534
DFCA Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1535
Direct Access Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1537
Double Power TRX Faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1538
Dual TRX usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1539
DAP ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1541
E-TRX Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1542
Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1544
GPRS Enabled TRX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1545
Horizon Associated TRX ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1547
Horizon EDGE Service Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1548
Horizon Power Finetune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1550
Horizon TRX Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1552
Level Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1553
LAC Of Interfering Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1554
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Table 1221
Table 1222
Table 1223
Table 1224
Table 1225
Table 1226
Table 1227
Table 1228
Table 1229
Table 1230
Table 1231
Table 1232
Table 1233
Table 1234
Table 1235
Table 1236
Table 1237
Table 1238
Table 1239
Table 1240
Table 1241
Table 1242
Table 1243
Table 1244
Table 1245
Table 1246
DN9813866
Metro TRX Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCC Of Interfering Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MNC Of Interfering Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Number Of TRX RF Power Levels . . . . . . . . . . . . . . . . . . . . . . . . . .
Optimum RX Level Downlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optimum RX Level Uplink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preferred BCCH TRX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RF Hopping Allowed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Server TRX Id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subslots For Signalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX DDU Association . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX Frequency Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX Half Rate Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX Identification With Frequency . . . . . . . . . . . . . . . . . . . . . . . . . .
MCPA TRX Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCPA TRX Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCPA TRX Port ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX RF Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX Shutdown Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX OSC Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRX Starting Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TSCU Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCSU Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TCSU Operational State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Id:0900d8058089b098
Confidential
1555
1556
1557
1559
1560
1561
1562
1563
1564
1565
1566
1567
1569
1570
1571
1572
1574
1575
1576
1577
1578
1580
1581
1584
1585
1586
57
BSS Radio Network Parameter Dictionary
58
Id:0900d8058089b098
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Summary of changes
Summary of changes
Changes between document issues are cumulative. Therefore, the latest document
issue contains all changes made to previous issues.
Changes made between issues 28-6 and 28-5
List of all new, modified, and removed parameters can be seen in the document Parameter Changes.
Changes made between issues 28-5 and 28-4
Description for the following parameters has been updated under managed object Base
Station Controller (BSC) radio network object parameters
•
local switching enabled for interscepted calls (LSEIC)
Description for the following parameters has been updated under managed object
Handover control (HOC) radio network object parameters
•
amrHoFrInHoThrDlRxQual (Intra HO Threshold Rx Qual AMR FR)
The following parameters have been added under the managed object Base Station
Controller (BSC) radio network object parameters:
•
•
•
•
•
precise paging enabled for repagings (PRECRP)
precise paging expanding delay (PRECPD)
precise paging location records living time (PRECPL)
precise paging MSC repaging delay (PRECMD)
precise paging TMSI optimization (PRECTO)
The following parameters have been added under the managed object Location Measurement Unit Area (LMUA) radio network object parameters:
•
•
lmu fno 26-multiplier usage (FMU)
lmu tsl fn delay (LTD)
File Based Provisioning supported field value changed to ‘true’ for channel 0 to 7 adminstrative state(-) under managed object Radio Timeslot (RTSL) radio network object
parameters.
Range value of the following parameters has been updated under managed object
Handover Control (HOC) radio network object parameters
•
•
•
OSC DFR Multiplexing Ul Rx Level Window (OMLW)
OSC DFR Demultiplexing Ul Rx Level Margin (ODMRG)
OSC DHR demultiplexing ul Rx level margin (ODMRG)
The following parameter has been added under managed object SEG-specific Base
Transceiver Station (SEGBTS) radio network object parameters.
•
•
caListPerBtsEnabled (CA List Per BTS Enabled)
precise paging usage (PRECPG)
Changes made between issues 28-4 and 28-3
Description for the following parameters has been updated under managed object
Adjacent GSM cell (ADCE) radio network object parameters
•
DN9813866
HO Target Area (HOTA)
Id:0900d8058089b04c
Confidential
59
Summary of changes
BSS Radio Network Parameter Dictionary
Description for the following parameters has been updated under managed object Base
Control Function (BCF) radio network object parameters
•
•
•
•
•
•
•
Abis Interface Connection type (AICT)
Attached CSDAP 1 (CSDAP1)
Attached CSDAP 2 (CSDAP2)
Attached CSDAP 3 (CSDAP3)
Attached CSDAP 4 (CSDAP4)
BCF HDLC ID List (BHIDL)
Packet Abis BCF Group ID (PABGID)
Description for the following parameters has been updated under managed object Base
Station Control (BSC) radio network object parameters
•
•
•
C/I Target OSC DHR (CIDHR)
Soft Blocking C/I OSC DHR (SBDHR)
Local Switching Enabled For Intercepted Calls (LSEIC)
Description for the following parameters has been updated under managed object Base
Tranceiver Station (BTS) radio network object parameters
•
•
•
•
•
•
Extended Cell GPRS/EDGE Enabled (EXGENA)
Extended Cell Location Keep Period (EXKEEP)
Initial MCS For Ext Area Acknowledged mode (MCEA)
Initial MCS For Ext Area Acknowledged mode (MCEU)
Radius Extension (EXT)
Super Radius Extension (SEXT)
Description for the following parameters has been updated under managed object
Circuit Switched Dynamic Abis Pool (CSDAP) radio network object parameters
•
•
•
BCF Abis IF (BAIF)
BCF Timeslot Shift (SHIFT)
CSDAP ID (ID)
Description for the following parameters has been updated under managed object
Handover Control (HOC) radio network object parameters
•
•
•
•
•
•
•
MS Distance HO Threshold Ext Cell Max (MAX)
MS Distance HO Threshold Ext Cell Min (MIN)
MS Distance HO Threshold Super Ext Cell Max (SMAX)
MS Distance HO Threshold Super Ext Cell Min (SMIN)
OSC DHR Demultiplexing Ul Rx Level Margin (ODMRG)
OSC DHR Multiplexing Ul Rx Level Threshold (OMLT)
OSC DHR Multiplexing Ul Rx Level Window (OMLW)
Description for the following parameters has been updated under managed object Radio
Timeslot (RTSL) radio network object parameters
•
•
•
•
•
•
60
Channel 0 Type (CH0)
Channel 1 Type (CH1)
Channel 2 Type (CH2)
Channel 3 Type (CH3)
Channel 4 Type (CH4)
Channel 5 Type (CH5)
Id:0900d8058089b04c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
•
•
Summary of changes
Channel 6 Type (CH6)
Channel 7 Type (CH7)
Description for the following parameters has been updated under managed object Tranceiver (TRX) radio network object parameters
•
•
•
E-TRX Type (ETRX)
TRX OSC Capability ()
TRX Starting Mode ()
Description for the following parameters has been added under managed object Base
Station Control (BSC) radio network object parameters
•
•
C/I Target OSC DFR (CIDFR)
Soft Blocking C/I OSC DFR (SBDFR)
Description for the following parameters has been added under managed object Base
Tranceiver Station (BTS) radio network object parameters:
•
•
•
•
•
•
•
8k TRAU for DFR Enabled (DFR8K)
Limit for Triggering OSC DFR Multiplexing (DFRLIM)
Nominal DL TX Power (NDTP)
Path Loss Offset DL (DPLO)
Path Loss Offset UL (UPLO)
Rx Signal Level Adjust (RXSLA)
Tx Signal Level Adjust (TXSLA)
The following parameters have been added under the managed object Handover
Control (HOC) radio network object parameters:
•
•
•
•
•
•
•
•
Intra HO Threshold Rx Qual AMR FR to DFR (IHRDFR)
OSC DFR Demultiplexing Rx Quality Threshold (ODFDQT)
OSC DFR Demultiplexing UL Rx Level Margin (OFDMRG)
OSC DFR Multiplexing Rx Quality Threshold (ODFMQT)
OSC DFR Multiplexing UL Rx Level Threshold (OFMLT)
OSC DFR Multiplexing UL Rx Level Window (OFMLW)
Threshold DL Rx Qual DFR (TDRQDF)
Threshold UL Rx Qual DFR (TURQdF)
The following parameters have been removed from the managed object Power Control
(POC) radio network object parameters:
•
•
•
•
PC
PC
PC
PC
Lower Threshold DL Rx
Lower Threshold UL Rx
Upper Threshold DL Rx
Upper Threshold UL Rx
Qual DFR (LDDFR)
Qual DFR (LUDFR)
Qual DFR (UDDFR)
Qual DFR (UUDFR)
Changes made between issues 28-3 and 28-2
List of all new, modified, and removed parameters can be seen in the document Parameter Changes.
Changes made between issues 28-2 and 28-1
Description for the following parameters has been updated under managed object
Power Control (POC) radio network object parameters:
•
DN9813866
pc lower threshold dl Rx qual AMR FR (LDRF)
Id:0900d8058089b04c
Confidential
61
Summary of changes
BSS Radio Network Parameter Dictionary
•
•
•
pc upper threshold dl Rx qual AMR FR (UDRF)
pc lower threshold dl Rx qual AMR HR (LDRH)
pc upper threshold dl Rx qual AMR HR (UDRH)
Description for the following parameters has been updated under managed object
Network Service Entity (NSE) radio network object parameters:
•
•
NSE NRI mask (-)
network resource identifier in decimal or network resource identifier in binary (NRID
or NRIB)
Description for the parameter NSE NRI mask (-) have been updated under managed
object Network Service Virtual Link (NSVL) radio network object parameters.
Parameter limit for triggering OSC DHR multiplexing (DHRLIM) was removed from
managed object SEG-specific Base Transceiver Station (SEGBTS) radio network object
parameters and added in the managed object Base Transceiver Station (BTS) radio
network object parameters.
The following parameters have been added under the managed object Power Control
(POC) radio network object parameters:
•
•
pc upper threshold dl Rx qual DHR (UDDHR)
pc upper threshold ul Rx qual DHR (UUDHR)
The following parameters have been removed from the managed object Base Station
Controller (BSC) radio network object parameters:
•
•
C/I target OSC DHR (CIDHR)
soft blocking C/I OSC DHR (SBDHR)
Changes made between issues 28-1 and 28-0
List of all new, modified, and removed parameters can be seen in the document Parameter Changes.
62
Id:0900d8058089b04c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Structure and conventions of BSS Radio Network Parameter Dictionary
1 Structure and conventions of BSS Radio
Network Parameter Dictionary
The aim of the parameter dictionary is to assist commissioning engineers and other
Base Station Controller (BSC) users to find certain Base Station System (BSS) parameters, their meanings, and relations to GSM specifications.
BSS radio network configuration parameters contain the configuration data and control
parameters of the radio network in the Base Station System. BSS radio network configuration parameters contain
•
•
configuration data and control parameters, and
transmission related parameters.
PAFILE and PRFILE parameters are excluded.
The parameters have been listed in alphabetical order by their MML Full Name. The
parameter tables are named by the Parameter name.
t
Parameters that are in another database or file are not listed here.
BSC radio network parameter information is also directly available and accessible via
NOLS Documentation Center's Reference Information Service. Information in the Reference Information Service is updated more frequently than the BSC NED browser environment.
How to read parameter tables:
The value '-' in the parameter table fields means that the information is not available,
unless indicated otherwise in the following table.
Parameter name
The user interface name for the parameter.
Abbreviated name
The parameter name used in XML and CSV plan files.
Managed object
The object for which the parameter is defined.
Multiplicity
The multiplicity of the parameter.
Description
Describes the purpose of the parameter and sometimes includes
extra information on the parameter.
Additional information
Includes additional information not given in the description of the
parameter.
Range
The user interface value range for the parameter.
Step
The step size for changing the parameter value.
Unit
The unit of the parameter's numeric value.
Formula for getting internal value
The formula for calculating the system internal value which is used
in radio network plan files.
Default value
The system default value specified by Nokia Siemens Networks.
Default value notes
Additional information (if any) on the default value.
Required on Creation
When the value is Mandatory, the parameter is required on creation.
Special value
Additional information (if any) on the special value of the parameter.
Table 1
DN9813866
How to read parameter tables
Id:0900d8058089b04d
Confidential
63
Structure and conventions of BSS Radio Network Parameter Dictionary
Related functions
BSS Radio Network Parameter Dictionary
The radio-network-related functions (in addition to the main function) of the parameter.
The value '-' means that the information is not relevant in BSC.
Modification
Requires object locking = The managed object must be locked by
the user before modification is possible.
Not modifiable = The parameter value can be modified only by recreating the managed object.
Online = The parameter value can be changed without any disturbance to ongoing calls.
Modified
Describes when the parameter can be modified.
Related parameters
Other parameters that affect the parameter.
Parameter relationships
Describes the dependencies between the parameter and the
related parameters.
Related options
Lists the option(s) related to the parameter. The option number in
parentheses relates to Q3 option numbers.
Related features
Lists the feature(s) related to the parameter.
Interfaces
The interfaces on which the parameter is transferred. From the
network management point of view, the parameters can be divided
into BSC/MSC/SGSN/RNC/AXC parameters, and planning and
management system (NetAct) parameters.
The BSC/MSC/SGSN/RNC/AXC parameters are needed in the
network whereas the planning and the management system parameters are auxiliary parameters that are not implemented in the
network, but are used in the network management and planning
processes.
References
References (if any) to 3GPP specifications
MML Commands
Lists the MML command(s) related to the parameter.
MML Abbreviated Name
The abbreviated name for the parameter in BSC MML.
MML Full Name
The user interface name for the parameter in BSC MML.
Segment Level Parameter
When the value is True, the parameter is a BTS segment level
parameter in Multi BCF control.
File Based Provisioning supported
When the value is True, the parameter supports File Based Plan
Provisioning. Always True or False.
Table 1
How to read parameter tables (Cont.)
Related topics:
•
•
64
Changes
• Parameter Changes
Reference
• Parameters
• PAFILE Timer and Parameter List
• PRFILE and FIFILE Parameter List
• Commands
• MML Commands
Id:0900d8058089b04d
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Autoconfiguration Pool (ACP) radio network object parameters
2 Autoconfiguration Pool (ACP) radio network
object parameters
2.1
Circuit (CRCT)
Parameter name
Circuit
Abbreviated name
circuit
Managed object
ACP
Multiplicity
1
Description
With this parameter you define the Abis interface ETPCM number and the first time slot of the pool. You can
also use the &&-structure to set the last time slot of the
pool or use the SIZE parameter to give the pool size
directly.
Parameter dictionary: Q3 name: pcmCircuit-ID, firstTSL,
lastTSL
Range: CRCT PCM: 0..3559
CRCT TSLs: in ETSI 1..31 and in ANSI 1..24
NOTE: 2048..3559 is reserved for OC-3/T1 administration area
NOTE: No NetAct interface.
Additional information
-
Range
0...3559
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
firstTsl of ACP - If MML parameter Circuit (CRCT) is
given, then First TSL is obligatory, lastTsl of ACP - If MML
parameter Circuit (CRCT) is given then Last TSL or Pool
Size is obligatory, pcmCircuitId of ACP - If MML parameter Circuit (CRCT) is given, then PCM Circuit ID is obligatory.
Parameter relationships
-
Related options
-
Related features
-
Table 2
DN9813866
Circuit
Id:0900d8058089b04e
Confidential
65
Autoconfiguration Pool (ACP) radio network object parameters
BSS Radio Network Parameter Dictionary
Interfaces
-
References
-
MML Commands
ESC, ESD, ESO
MML Abbreviated Name
CRCT
MML Full Name
Circuit
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 2
2.2
Circuit (Cont.)
pool id (ID)
Parameter name
ACP ID
Abbreviated name
id
Managed object
ACP
Multiplicity
1
Description
With this parameter you identify the Pool id of the ACP
object.
Additional information
-
Range
1...254
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
References
-
MML Commands
ESD, ESO
Table 3
66
RACApp <-> RAC
RAC <-> BSC
ACP ID
Id:0900d8058089b04e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Autoconfiguration Pool (ACP) radio network object parameters
MML Abbreviated Name
ID
MML Full Name
pool id
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 3
2.3
ACP ID (Cont.)
pool size (SIZE)
Parameter name
Pool Size
Abbreviated name
poolSize
Managed object
ACP
Multiplicity
1
Description
With this parameter you define the Pool size. The
minimum pool size is 3.
NOTE:
No NetAct interface.
Additional information
-
Range
3...31
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
-
References
-
MML Commands
ESC
MML Abbreviated Name
SIZE
MML Full Name
pool size
Table 4
DN9813866
Pool Size
Id:0900d8058089b04e
Confidential
67
Autoconfiguration Pool (ACP) radio network object parameters
Segment Level Parameter
BSS Radio Network Parameter Dictionary
-
File Based Provisioning sup- false
ported
Table 4
68
Pool Size (Cont.)
Id:0900d8058089b04e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
3 Adjacent GSM Cell (ADJC/ADCE) radio
network object parameters
3.1
adjacent cell identification (CI)
Parameter name
CI
Abbreviated name
adjacentCellIdCI
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the CI of the adjacent cell
(target cell). The parameter is a part of the Cell Id parameter which consists of Mobile Country Code, Mobile
Network Code, Location Area Code and the Cell Id of the
target cell.
NOTE: MML Modification: Online
Additional information
-
Range
0...65535
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-1
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
Interfaces
References
3GPP Reference: 44.018
MML Commands
EAC, EAD, EAM, EAO
MML Abbreviated Name
CI
MML Full Name
adjacent cell identification
Segment Level Parameter
-
Table 5
DN9813866
Planner <-> RAC
RAC <-> Optimizer
RAC -> BSC
CI
Id:0900d8058089b04f
Confidential
69
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 5
3.2
CI (Cont.)
adjacent cell index (INDEX)
Parameter name
Adjacent Cell Index
Abbreviated name
adjcIndex
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the adjacent cell index for
the adjacent GSM cell.
MML NOTE: The smallest free index value for serving cell
is searched and used.
Additional information
-
Range
0...31
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-1
Default value notes
The smallest free index value for serving cell is searched
and used.
Required on Creation
mandatory
Special value
Set by NetAct system (-1)
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
Interfaces
References
-
MML Commands
EAC, EAD, EAM, EAX, EAO, EAP
MML Abbreviated Name
INDEX
MML Full Name
adjacent cell index
Table 6
70
RAC -> BSC
Planner <-> RAC
Optimizer <-> RAC
Adjacent Cell Index
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 6
3.3
Adjacent Cell Index (Cont.)
adjacent cell layer (ACL)
Parameter name
Adjacent Cell Layer
Abbreviated name
adjCellLayer
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the adjacent cell layer in
relation to the active cell. A call can be handed over to the
cells that are visible to the serving cell by adjacency definition. This means the cells of upper layer, serving layer
and lower layer. The adjacent cell layer definition can be
used, for example, in umbrella and power budget handovers in defining the target cells according to their layer.
NOTE:
MML range:
N
... ADJACENT CELL LAYER IS NOT IN USE
SAME ... IN THE SAME LAYER WITH THE SERVING
CELL
UPPER ... IN A HIGHER LAYER THAN THE SERVING
CELL
LOWER ... IN A LOWER LAYER THAN THE SERVING
CELL
Additional information
-
Range
Not Used (0), Same Layer (1), Upper Layer (2), Lower
Layer (3)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Not Used ==> 0
Same Layer ==> 1
Upper Layer ==> 2
Lower Layer ==> 3
Default value
Not Used (0)
Default value notes
Not used
Required on Creation
optional
Related functions
-
Modification
Online
Table 7
DN9813866
Adjacent Cell Layer
Id:0900d8058089b04f
Confidential
71
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
-
•
•
•
•
Interfaces
Fast Moving MS Handling In Macro Cell (15)
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
ACL
MML Full Name
adjacent cell layer
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 7
3.4
Adjacent Cell Layer (Cont.)
Adjacent GPRS enabled (AGENA)
Parameter name
GPRS Enabled
Abbreviated name
gprsEnabled
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define whether the GPRS capability is enabled or disabled in the adjacent cell.
In the adjacent cell creation if this parameter is not given
and the SEG and the adjacent cell are in the same BSS,
the value of this parameter is copied from the SEG.
NOTE:
MML Modification: Online
Additional information
-
Range
GPRS is disabled in the adjacent cell (N) (0), GPRS is
enabled in the adjacent cell (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
GPRS is disabled in the adjacent cell (N) ==> 0
GPRS is enabled in the adjacent cell (Y) ==> 1
Default value
Table 8
72
GPRS is disabled in the adjacent cell (N) (0)
GPRS Enabled
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
•
Interfaces
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
AGENA
MML Full Name
Adjacent GPRS enabled
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 8
3.5
AMR target cell of direct access to desired layer (DADLA)
Parameter name
AMR Target Cell Of Direct Access To Desired Layer
Abbreviated name
amrDadlbTargetCell
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define whether the direct access
to desired layer/band handover is applied to the adjacent
cell in case of AMR call establishment and whether AMR
target cells are prioritised in handover. In handover this
parameter indicates whether AMR is enabled in the target
cell. These AMR-enabled cells are then prioritised over
other cells for AMR capable MS.
Additional information
-
Range
DADLA is not applied (N) (0), DADLA is applied (Y) (1)
Step
-
Unit
-
Table 9
DN9813866
GPRS Enabled (Cont.)
AMR Target Cell Of Direct Access To Desired Layer
Id:0900d8058089b04f
Confidential
73
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Formula for getting internal
value
BSS Radio Network Parameter Dictionary
gui ==> internal
DADLA is not applied (N) ==> 0
DADLA is applied (Y) ==> 1
Default value
DADLA is not applied (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Direct Access To Desired Layer/Band (35) (optional)
AND ( AMR FR (50) (optional) OR AMR HR (72)
(optional) )
Related features
•
BSS20249: AMR FR Licence Control
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
DADLA
MML Full Name
AMR target cell of direct access to desired layer
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 9
3.6
BCCH frequency (FREQ)
Parameter name
BCCH Frequency
Abbreviated name
bcchFrequency
Managed object
ADCE
Multiplicity
1
Table 10
74
AMR Target Cell Of Direct Access To Desired Layer (Cont.)
BCCH Frequency
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Description
With this parameter you define the BCCH frequency of an
adjacent cell.
NOTE:
The frequency must be equal to the BCCH frequency of
an adjacent BTS.
NOTE:
Range:
GSM 800: 128...251
GSM 900: 1..124 and 975..1023, 0
GSM 1800: 512..885
GSM 1900: 512..810
DUAL 900/1800 <option>: 1...124, 512...885 or
975...1023, 0
DUAL 800/1800 <option>:128...251 or 512...885
DUAL 800/1900 <option>: 128...251 or 512...810
NOTE:
MML modification: Online
NOTE:
The parameter is obligatory if the adjacent cell and the
BTS are not under the same BSS. The parameter is also
obligatory if the adjacent cell and the BTS are under the
same BSS, but the adjacent cell does not have a BCCHTRX yet.
Additional information
-
Range
0...65535
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
Table 10
DN9813866
•
•
•
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
BCCH Frequency (Cont.)
Id:0900d8058089b04f
Confidential
75
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
•
References
3GPP Reference: 44.018
MML Commands
EAC, EAM, EAO, EAP
MML Abbreviated Name
FREQ
MML Full Name
BCCH frequency
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 10
3.7
BCCH Frequency (Cont.)
BTS colour code (BCC)
Parameter name
BSIC BCC
Abbreviated name
adjCellBsicBcc
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the BTS colour code
number.
NOTE:
The BSIC parameter, which is used to identify the BTS, is
composed of the NCC and BCC parameters. BSIC must
be equal to the BSIC parameter of adjacent BTS.
This parameter is mandatory in creation if the adjacent
cell and the BTS are not under the same BSS.
Additional information
-
Range
0...7
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Table 11
76
BSIC BCC
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Interfaces
•
•
•
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
3GPP Reference: 44.018
MML Commands
EAC, EAM, EAO, EAP
MML Abbreviated Name
BCC
MML Full Name
BTS colour code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 11
3.8
BSIC BCC (Cont.)
C/I estimation weight (W1-W5)
Parameter name
Reference Cell C/I Estimation Weight
Abbreviated name
ciEstWeight
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the weighting coefficient
of the reference cell.
NOTE:
MML Range: 0..10
The value 0 is default and detaches the corresponding
reference cell from the adjacent cell.
Additional information
-
Range
1...10
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
1
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Table 12
DN9813866
•
C/I Based Handover Candidate Evaluation (18)
Reference Cell C/I Estimation Weight
Id:0900d8058089b04f
Confidential
77
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Related features
BSS Radio Network Parameter Dictionary
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAX, EAO
MML Abbreviated Name
W1-W5
MML Full Name
C/I estimation weight
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 12
3.9
Reference Cell C/I Estimation Weight (Cont.)
cell identification of reference cell (CI1-CI5)
Parameter name
Reference Cell CI
Abbreviated name
adjIdCi
Managed object
ADCE
Multiplicity
1
Description
With this parameter you identify the reference cell.
Additional information
-
Range
0...65535
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
Table 13
78
•
C/I Based Handover Candidate Evaluation (18)
-
Reference Cell CI
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAX, EAO
MML Abbreviated Name
CI1-CI5
MML Full Name
cell identification of reference cell
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 13
3.10
Reference Cell CI (Cont.)
cell type (CTY)
Parameter name
IDR Cell Type
Abbreviated name
cellType
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the adjacent cell type.
NOTE:
The cell type parameter of the adjacent cell must be the
same.
NOTE:
MML modification: Online
Additional information
-
Range
GSM (0), MCN (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
GSM ==> 0
MCN ==> 1
Default value
GSM (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Table 14
DN9813866
IDR Cell Type
Id:0900d8058089b04f
Confidential
79
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Parameter relationships
Related options
Related features
BSS Radio Network Parameter Dictionary
-
•
-
•
•
•
Interfaces
Intelligent Directed Retry (IDR) (20)
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
CTY
MML Full Name
cell type
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 14
3.11
IDR Cell Type (Cont.)
chained adj cell (CHAIN)
Parameter name
Chained Adj Cell
Abbreviated name
chainedAdjacentCell
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the adjacent cell as a
chained cell, to which the rapid field drop handover
criteria are applied.
Additional information
-
Range
adjacent cell is not chained (N) (0), adjacent cell is
chained (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
adjacent cell is not chained (N) ==> 0
adjacent cell is chained (Y) ==> 1
Default value
adjacent cell is not chained (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Table 15
80
Chained Adj Cell
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Parameter relationships
-
•
Related options
Related features
Chained Cells In Rapid Field Drop (9)
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
CHAIN
MML Full Name
chained adj cell
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 15
3.12
directed retry threshold (DRT)
Parameter name
Directed Retry Threshold
Abbreviated name
drThreshold
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the threshold value
of the signal strength in the adjacent cell for the
Directed Retry procedure. If the signal strength
level in the cell is lower than this threshold value,
adjacent cell is not accepted as a candidate in
directed retry.
Additional information
-
Range
-110...-47
Step
1
Unit
dBm
Formula for getting
internal value
internal_value = (gui_value + 110)
Default value
-100 dBm
Default value notes
-
Required on Creation
optional
Related functions
-
Table 16
DN9813866
Chained Adj Cell (Cont.)
Directed Retry Threshold
Id:0900d8058089b04f
Confidential
81
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Feature dependencies
-
Interfaces
•
•
•
•
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
DRT
MML Full Name
directed retry threshold
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 16
3.13
BSS Radio Network Parameter Dictionary
Intelligent Directed Retry (IDR) (20) (optional)
OR Directed Retry (1) (optional)
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
Directed Retry Threshold (Cont.)
DTM enabled (DTM)
Parameter name
DTM Enabled
Abbreviated name
dtmEnabled
Managed object
ADCE
Multiplicity
1
Description
Indicates if adjacent cell supports DTM or not.
MML NOTE: Parameter can be given at Adjacent Cell
creation and modification when the neighbour cell is
external, that is, under another BSC. If Adjacent Cell is
created with BTS reference, the value is copied from the
reference BTS (Master-BTS). In case of BSC internal
adjacent cell the parameter value depends on the "DTM
Enabled" value of the reference segment.
NOTE: When not using DTM feature, the parameter can
be given for an external adjacency.
NOTE: MML Modification: Online
Additional information
-
Range
DTM disabled (N) (0), DTM enabled (Y) (1)
Table 17
82
DTM Enabled
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
DTM disabled (N) ==> 0
DTM enabled (Y) ==> 1
Default value
DTM disabled (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
dtmEnabled of BTS - If an adjacent cell is created with a
BTS reference, the value is copied from the referenced
BTS (Master-BTS).
Parameter relationships
-
Related options
•
Dual Transfer Mode and Statistics (DTM) (91)
Related features
•
BSS20088: Dual Transfer Mode (DTM)
Interfaces
•
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
DTM
MML Full Name
DTM enabled
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 17
3.14
DTM power budget margin (DPM)
Parameter name
DTM Power Budget Margin
Abbreviated name
dtmPowerBudgetMargin
Managed object
ADCE
Multiplicity
1
Table 18
DN9813866
DTM Enabled (Cont.)
DTM Power Budget Margin
Id:0900d8058089b04f
Confidential
83
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define a power budget handover
threshold for moving:
a) DTM capable mobiles to a DTM capable neighbour cell
when the serving cell is not supporting DTM,
b) DTM call attempts to a DTM capable neighbour cell
when there are no free resources for a DTM allocation in
the serving DTM capable cell,
c) DTM calls from a DTM capable cell to a non-DTM
capable cell.
Additional information
-
Range
-24...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = (gui_value + 24)
Default value
6 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Dual Transfer Mode and Statistics (DTM) (91)
Related features
•
BSS20088: Dual Transfer Mode (DTM)
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
DPM
MML Full Name
DTM power budget margin
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 18
3.15
enable derived handover power (DHOPWR)
Parameter name
Enable Derived Handover Power
Abbreviated name
enableDerivedHandoverPower
Table 19
84
DTM Power Budget Margin (Cont.)
Enable Derived Handover Power
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Managed object
ADCE
Multiplicity
1
Description
With this parameter you enable the Downlink,
Uplink or both Derived Handover Power feature.
NOTE: MML Range:
0: Disabled
1: Enabled in UL direction
2: Enabled in DL direction
3: Enabled in both, UL and DL direction
NOTE: Parameter is visible for all site types but,
valid only for BTSplus site type
Additional information
-
Range
DISABLED (0), ENABLED UL (1), ENABLED DL
(2), ENABLED UL DL (3)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
DISABLED ==> 0
ENABLED UL ==> 1
ENABLED DL ==> 2
ENABLED UL DL ==> 3
Default value
DISABLED (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS21469: BS2xx@Flexi BSC product family
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
DHOPWR
MML Full Name
enable derived handover power
Table 19
DN9813866
Enable Derived Handover Power (Cont.)
Id:0900d8058089b04f
Confidential
85
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 19
3.16
BSS Radio Network Parameter Dictionary
Enable Derived Handover Power (Cont.)
enable HO margin lev qual (MRGS)
Parameter name
Enable HO Margin Lev Qual
Abbreviated name
enableHoMarginLevQual
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define whether the handover
margins for signal level and quality will be taken into
account in the handover decision algorithm.
Additional information
-
Range
not used (N) (0), used (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
not used (N) ==> 0
used (Y) ==> 1
Default value
used (Y) (1)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
References
-
MML Commands
EAM, EAO
MML Abbreviated Name
MRGS
Table 20
86
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
Enable HO Margin Lev Qual
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
MML Full Name
enable HO margin lev qual
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 20
3.17
Enable HO Margin Lev Qual (Cont.)
fast moving threshold (FMT)
Parameter name
Fast Moving Threshold
Abbreviated name
fastMovingThreshold
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the limit which is
compared with the identification counter (fast moving MS)
in the adjacent cell. If the limit is exceeded, the call is
handed over from the macrocell to the best microcell.
Additional information
-
Range
0...255
Step
1
Unit
SACCH frame
Formula for getting internal
value
internal_value = gui_value
Default value
0 SACCH frame
Default value notes
Not in use
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
Fast Moving MS Handling In Macro Cell (15)
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
FMT
Table 21
DN9813866
•
Fast Moving Threshold
Id:0900d8058089b04f
Confidential
87
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
MML Full Name
fast moving threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 21
3.18
Fast Moving Threshold (Cont.)
GPRS MS TX pwr max CCH (GTXP1)
Parameter name
GPRS MS Tx Pwr Max CCH
Abbreviated name
gprsMsTxpwrMaxCCH
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the maximum transmission power an MS may use when accessing a packet
control channel in the adjacent cell. This is used when
BCCH is in GSM 900 or GSM 800 frequency band.
NOTE:
MML modification: Online
Additional information
-
Range
5...39
Step
2
Unit
dBm
Formula for getting internal
value
internal_value = (gui_value - 43) / -2
Default value
33 dBm
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 44.060, 45.008
MML Commands
Table 22
88
•
EAC, EAM, EAO, EQG, EQO
GPRS MS Tx Pwr Max CCH
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
MML Abbreviated Name
GTXP1
MML Full Name
GPRS MS TX pwr max CCH
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 22
3.19
GPRS MS Tx Pwr Max CCH (Cont.)
GPRS MS TX pwr max CCH 1x00 (GTXP2)
Parameter name
GPRS MS Tx Pwr Max CCH 1x00
Abbreviated name
gprsMsTxPwrMaxCCH1x00
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the maximum transmission power an MS may use when accessing a packet
control channel in the adjacent cell. This is used when
BCCH is in GSM 1900 or GSM 1800 frequency band.
NOTE: MML value range:
GSM 1800: 0..36 dBm (step size 2)
GSM 1900: 0..32 dBm (step size 2) and 33 dBm
NOTE: NetAct internal value range:
GSM 1800:
0..30 dBm: 0..15 (UI value - 30)/-2
32 dBm: 31
34 dBm: 30
36 dBm: 29
GSM 1900:
0..30 dBm: 0..15 (UI value - 30)/-2
32 dBm: 31
33 dBm: 30
NOTE: MML modification: Online
Additional information
-
Range
0...36
Step
2
Unit
dBm
Formula for getting internal
value
internal_value = gui_value
Default value
30 dBm
Default value notes
-
Required on Creation
optional
Table 23
DN9813866
GPRS MS Tx Pwr Max CCH 1x00
Id:0900d8058089b04f
Confidential
89
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 44.060, 45.008
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
GTXP2
MML Full Name
GPRS MS TX pwr max CCH 1x00
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 23
3.20
GPRS penalty time (GPET)
Parameter name
GPRS Penalty Time
Abbreviated name
gprsPenaltyTime
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the duration for which the
GPRS Temporary Offset (GTEO) applies.
Additional information
-
Range
10...320
Step
10
Unit
s
Formula for getting internal
value
internal_value = (gui_value - 10) / 10
Default value
10 s
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Table 24
90
GPRS MS Tx Pwr Max CCH 1x00 (Cont.)
GPRS Penalty Time
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 44.060
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
GPET
MML Full Name
GPRS penalty time
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 24
3.21
GPRS rxlev Access min (GRXP)
Parameter name
GPRS Rxlev Access Min
Abbreviated name
gprsRxlevAccessMin
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the minimum power level
an MS has to receive before it is allowed to access the
adjacent cell.
Additional information
-
Range
-110...-47
Step
1
Unit
dBm
Formula for getting internal
value
internal_value = (gui_value + 110)
Default value
-105 dBm
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Table 25
DN9813866
GPRS Penalty Time (Cont.)
GPRS Rxlev Access Min
Id:0900d8058089b04f
Confidential
91
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Related parameters
-
Parameter relationships
-
Related options
Related features
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 44.060
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
GRXP
MML Full Name
GPRS rxlev Access min
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 25
3.22
GPRS temporary offset (GTEO)
Parameter name
GPRS Temporary Offset
Abbreviated name
gprsTemporaryOffset
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the negative offset of the
C32 reselection criterion for the duration of the GPRS
penalty time (GPET) after the MS has placed the cell on
the list of the strongest carriers. It is used by the mobile
station as part of its calculation of C32 for the cell reselection process. The parameter can be changed in 10 dB
steps. Value 70 dB means infinity.
Additional information
-
Range
0...70
Step
10
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 10
Default value
0 dB
Default value notes
-
Required on Creation
optional
Special value
Infinity 70 (7)
Table 26
92
GPRS Rxlev Access Min (Cont.)
GPRS Temporary Offset
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
3GPP Reference: 44.060
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
GTEO
MML Full Name
GPRS temporary offset
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 26
3.23
GPRS Temporary Offset (Cont.)
HO margin delay time (HOMD)
Parameter name
HO Margin Delay Time
Abbreviated name
hoMarginDelayTime
3GPP name
-
Managed Object
ADCE
Multiplicity
1
Description
The parameter specifies the time an immediate
handover request is delayed when a power budget
handover is requested. The value is expressed in
number of SACCH multiframe periods.
Parameter is valid only for BTSplus site type
Additional information
-
Range
0...255
Step
1
Units
SACCH frames
Formula for getting
internal value
internal_value = gui_value
Table 27
DN9813866
HO margin delay time
Id:0900d8058089b04f
Confidential
93
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Default value
0
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
RG301398 RG20 (BSS) Support for BS2xx
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
-
File based provisioning
supported
true
MML Abbreviated Name
HOMD
MML Commands
EAC, EAM, EAO
MML Full Name
HO margin delay time
Segment Level Parameter
-
Table 27
3.24
HO margin delay time (Cont.)
HCS signal level threshold (HCS)
Parameter name
HCS Threshold
Abbreviated name
hcsThreshold
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the signal strength threshold for applying HCS in GPRS reselection. If this parameter is not given in the adjacent cell creation and the SEG
and the adjacent cell are in the same BSS, the value of
this parameter is copied from the SEG.
NOTE:
MML range: -110,-108,...,-48 (dB) and N
NOTE:
MML modification: Online
Additional information
Table 28
94
-
HCS Threshold
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Range
-110...-48
Step
2
Unit
dB
Formula for getting internal
value
internal_value = (gui_value + 110) / 2
Default value
255 dB
Default value notes
-
Required on Creation
optional
Special value
Not used (255)
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 44.060
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
HCS
MML Full Name
HCS signal level threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 28
3.25
HO level umbrella (AUCL)
Parameter name
HO Level Umbrella
Abbreviated name
hoLevelUmbrella
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the minimum signal level
of an adjacent cell, when a handover is allowed to an
adjacent umbrella cell.
Additional information
-
Range
-110...-47
Table 29
DN9813866
HCS Threshold (Cont.)
HO Level Umbrella
Id:0900d8058089b04f
Confidential
95
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Step
1
Unit
dBm
Formula for getting internal
value
internal_value = (gui_value + 110)
Default value
-47 dBm
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
AUCL
MML Full Name
HO level umbrella
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 29
3.26
HO load factor (OF)
Parameter name
HO Load Factor
Abbreviated name
hoLoadFactor
Managed object
ADCE
Multiplicity
1
Table 30
96
HO Level Umbrella (Cont.)
HO Load Factor
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Description
With this parameter you define how much the priority of
the target cell will be decreased if the cell is overloaded.
The parameter is used only for the cells under one BSC
if the BSC cannot get information about the loading of
other cells.
NOTE:
The HO load factor cannot be greater than the HO priority
level.
Additional information
-
Range
0...7
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
1
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
OF
MML Full Name
HO load factor
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 30
3.27
HO Load Factor (Cont.)
HO margin lev (LMRG)
Parameter name
Table 31
DN9813866
HO Margin Lev
HO Margin Lev
Id:0900d8058089b04f
Confidential
97
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Abbreviated name
hoMarginLev
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define a threshold for a handover
caused by signal level.
Additional information
-
Range
-24...24
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
3 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
LMRG
MML Full Name
HO margin lev
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 31
3.28
HO margin pbgt (PMRG)
Parameter name
HO Margin PBGT
Abbreviated name
hoMarginPbgt
Managed object
ADCE
Table 32
98
HO Margin Lev (Cont.)
HO Margin PBGT
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Multiplicity
1
Description
With this parameter you define a threshold in the power
budget process. The handover margin prevents repeated
handover between adjacent cells.
Additional information
-
Range
-24...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
6 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
PMRG
MML Full Name
HO margin pbgt
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 32
3.29
HO margin qual (QMRG)
Parameter name
HO Margin Qual
Abbreviated name
hoMarginQual
Managed object
ADCE
Multiplicity
1
Table 33
DN9813866
HO Margin PBGT (Cont.)
HO Margin Qual
Id:0900d8058089b04f
Confidential
99
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Description
With this parameter you define a threshold for a handover
caused by signal quality.
Additional information
-
Range
-24...24
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
0 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
QMRG
MML Full Name
HO margin qual
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 33
3.30
HO priority level (PRI)
Parameter name
HO Priority Level
Abbreviated name
hoPriorityLevel
Managed object
ADCE
Multiplicity
1
Table 34
100
HO Margin Qual (Cont.)
HO Priority Level
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Description
With this parameter you define the priority level for an
adjacent cell. The priority level is used for target cell evaluation by the handover control process. By using priority
levels for the handover algorithm, it is possible to take
into account the location of the adjacent cell. 0 is the
lowest and 7 is the highest priority.
Additional information
-
Range
0...7
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
3
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
3GPP Reference: 45.008
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
PRI
MML Full Name
HO priority level
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 34
3.31
HO target area (HOTA)
Parameter name
HO Target Area
Abbreviated name
hoTargetArea
3GPP name
-
Table 35
DN9813866
HO Priority Level (Cont.)
HO Target Area
Id:0900d8058089b04f
Confidential
101
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define whether the adjacent cell
is a normal or an extended cell. The meanings of the
HOTA values are:
0 ... Normal cell or 2nd generation extended cell
1 ... UltraSite, Talk-family, Flexi EDGE, Flexi Multiradio or
BTSplus extended cell, BSC tries to allocate a new
channel from a normal transceiver (N-TRX)
2 ... UltraSite, Talk-family, Flexi EDGE, Flexi Multiradio or
BTSplus extended cell, BSC tries to allocate a new
channel from an extended transceiver (E-TRX)
3 ... UltraSite, Talk-family, Flexi EDGE, Flexi Multiradio or
BTSplus extended cell, BSC tries to allocate a new
channel from a transceiver that is of the same type as the
transceiver where the call exists
4 ... Flexi EDGE, Flexi Multiradio or BTSplus super
extended cell, BSC tries to allocate a new channel from a
super extended transceiver (S-TRX)
MML NOTE:
The allowed values depend on the generations of the
source and target BTS in the following way:
BTS GEN SRC............BTS GEN. ADJ CELL
..............................................................................HOTA
2ND GENERATION,.....2ND GENERATION,...........................................................................0
TALK-FAMILY,.............PRIMESITE,
PRIMESITE,................METROSITE,
METROSITE,...............INSITE,
Table 35
102
HO Target Area (Cont.)
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Description
DN9813866
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
With this parameter you define whether the adjacent cell
is a normal or an extended cell. The meanings of the
HOTA values are:
0 ... Normal cell or 2nd generation extended cell
1... UltraSite, Talk-family, Flexi EDGE, Flexi Multiradio or
BTSplus extended cell, BSC tries to allocate a new
channel from a normal transceiver (N-TRX)
2 ... UltraSite, Talk-family, Flexi EDGE, Flexi Multiradio or
BTSplus extended cell, BSC tries to allocate a new
channel from an extended transceiver (E-TRX)
3 ... UltraSite, Talk-family, Flexi EDGE, Flexi Multiradio or
BTSplus extended cell, BSC tries to allocate a new
channel from a transceiver that is of the same type as the
transceiver where the call exists
4 ... Flexi EDGE, Flexi Multiradio or BTSplus super
extended cell, BSC tries to allocate a new channel from a
super extended transceiver (S-TRX)
MML NOTE: The allowed values depend on the generations of the source and target BTS in the following way:
BTS GENERATION SRC...BTS GEN. ADJ CELL..HOTA
2ND GENERATION,..........2ND GENERATION,.....0
TALK-FAMILY,...................PRIMESITE,
PRIMESITE,..................... .METROSITE,
METROSITE,.................... INSITE,
INSITE,...............................FLEXI EDGE,
ULTRASITE,...................... FLEXI MULTIRADIO OR
FLEXI EDGE,.................... BTSPLUS
FLEXI MULTIRADIO OR
BTSPLUS
2ND GENERATION,...........TALK-FAMILY,............0,1,2
PRIMESITE,........................ULTRASITE,
METROSITE,.......................FLEXI EDGE,
INSITE,................................FLEXI MULTIRADIO OR
FLEXI EDGE,..................... BTSPLUS
FLEXI MULTIRADIO OR
BTSPLUS
TALK-FAMILY,...................TALK-FAMILY,..........0,1,2,3
ULTRASITE,......................ULTRASITE,
FLEXI EDGE.....................FLEXI EDGE,
FLEXI MULTIRADIO OR..FLEXI MULTIRADIO OR
BTSPLUS..........................BTSPLUS
FLEXI EDGE.....................FLEXI EDGE............0,1,2,3,4
FLEXI MULTIRADIO OR...FLEXI MULTIRADIO OR
BTSPLUS......................... BTSPLUS
In the case of an inter-BSS handover, the MS is always
handled over to TRX in the outer coverage area of the cell
if target cell is cell without LRTCH channel. When
LRTCH is configured in target cell the TRX is selected
according the location of mobile.
MML NOTE: Value 4 is allowed when 105 km Extended
Cell(FlexiEDGE BTS) feature is ON or CONF.
You can check the values of the HO target area parameter with the EAT command.
Id:0900d8058089b04f
NOTE: Parameter is not supported for Flexi Compact 103
Confidential
BTSs.
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Additional information
-
Range
Normal or 2nd generation extended cell (0), E Cell
Normal TRX Alloc (1), E Cell Extended TRX Alloc (2), E
Cell Same Type As TRX Alloc (3), S Cell Extended TRX
Alloc (4)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Normal or 2nd generation extended cell ==> 0
E Cell Normal TRX Alloc ==> 1
E Cell Extended TRX Alloc ==> 2
E Cell Same Type As TRX Alloc ==> 3
S Cell Extended TRX Alloc ==> 4
Default value
Normal or 2nd generation extended cell (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Extended Cell For US (88) (optional) OR Extended
Cell Radius (10) (optional) OR Extended cell range
for CS (108) (optional) OR 105km Extended Cell CS
(123) (optional)
Feature dependencies
•
•
BSS20882: Extended cell range for CS
BSS21277: 105km Extended Cell CS
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification,
NSN reference: BSS101482 - Extended cell functionalities for Flexi Multiradio BTS
•
File Based Provisioning
supported
true
MML Abbreviated Name
HOTA
MML Commands
EAC, EAM, EAO, EAT
Table 35
104
HO Target Area (Cont.)
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
MML Full Name
HO target area
Segment Level Parameter
-
Table 35
HO Target Area (Cont.)
BTS GENERATION SOURCE
BTS GEN. ADJACENT CELL
HOTA
2nd generation, Talkfamily, Pri- 2nd generation, PrimeSite MetmeSite, MetroSite, InSite, Ultra- roSite, InSite, Flexi EDGE, Flexi
Site, Flexi EDGE, Flexi
Multiradio or BTSplus
Multiradio or BTSplus
0
2nd generation, PrimeSite MetroSite, InSite, Flexi EDGE, Flexi
Multiradio or BTSplus
Talkfamily, UltraSite, Flexi
EDGE, Flexi Multiradio or
BTSplus
0, 1, 2
Talkfamily, UltraSite, Flexi
EDGE, Flexi Multiradio or
BTSplus
Talkfamily, UltraSite, Flexi
EDGE, Flexi Multiradio or
BTSplus
0, 1, 2, 3
Flexi EDGE, Flexi Multiradio or
BTSplus
Flexi EDGE, Flexi Multiradio or
BTSplus
0, 1, 2, 3, 4
Table 36
HO Target area
In the case of an inter-BSS handover, the MS is always handed over to the TRX in the
outer coverage area of the cell if the target cell is without an LRTCH channel. When
LRTCH is configured in the target cell, the TRX is selected according the location of the
MS.
3.32
IBNACC state ()
Parameter name
IBNACC State
Abbreviated name
ibnaccState
Managed object
ADCE
Multiplicity
1
Description
This parameter is used to determine whether
NACC is supported in adjacent segment in adjacent
BSC. The parameter is insignificant for adjacent
segments in own BSC.
This parameter is modified only by the system.
Note: Only in MML Output
Additional information
-
Range
NACC is supported in adjacent segment (0), NACC
is not supported in adjacent segment (1)
Table 37
DN9813866
IBNACC State
Id:0900d8058089b04f
Confidential
105
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
NACC is supported in adjacent segment ==> 0
NACC is not supported in adjacent segment ==> 1
Default value
NACC is not supported in adjacent segment (1)
Default value notes
-
Required on Creation
Value set by the system
Related functions
-
Modification
Not modifiable
Modified
read-only
Related parameters
naccUsage of BSC - The parameter is dependant
on the BSC parameter NACC enabled and can be
modified to 0 (NACC is supported in adjacent
segment) only, if the NACC enabled parameter is Y.
Parameter relationships
-
Related options
•
NACC (Network Assisted Cell Change) (81)
Feature dependencies
•
BSS20083: Inter-BSC Network Assisted Cell
Change (NACC)
Interfaces
•
BSC -> RAC
References
-
MML Commands
EAO
MML Abbreviated Name
-
MML Full Name
IBNACC state
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 37
3.33
level adjustment (L1-L5)
Parameter name
Reference Cell Level Adjustment
Abbreviated name
levelAdj
Managed object
ADCE
Multiplicity
1
Table 38
106
IBNACC State (Cont.)
Reference Cell Level Adjustment
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Description
With this parameter you define the difference in signal
levels between the actual co-frequency cell of the
handover candidate and the reference cell which simulates the co-frequency cell.
Additional information
-
Range
-63...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
0 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
C/I Based Handover Candidate Evaluation (18)
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAX, EAO
MML Abbreviated Name
L1-L5
MML Full Name
level adjustment
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 38
3.34
location area code (LAC)
Parameter name
LAC
Abbreviated name
adjacentCellIdLac
Managed object
ADCE
Multiplicity
1
Table 39
DN9813866
Reference Cell Level Adjustment (Cont.)
LAC
Id:0900d8058089b04f
Confidential
107
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the LAC of the adjacent
cell (target cell). The identification consists of the Mobile
Country Code Number, Mobile Network Code Number,
Cell Identification and the Location Area Code.
NOTE:
MML modification: Online
Additional information
-
Range
1...65533
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
Interfaces
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAD, EAO, EAM
MML Abbreviated Name
LAC
MML Full Name
location area code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 39
3.35
location area code of reference cell (LAC1-LAC5)
Parameter name
Reference Cell LAC
Abbreviated name
adjIdLac
Managed object
ADCE
Table 40
108
LAC (Cont.)
Reference Cell LAC
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Multiplicity
1
Description
With this parameter you identify the location area number
of the reference cell.
Additional information
-
Range
1...65533
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
C/I Based Handover Candidate Evaluation (18)
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAX, EAO
MML Abbreviated Name
LAC1-LAC5
MML Full Name
location area code of reference cell
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 40
3.36
mobile country code (MCC)
Parameter name
MCC
Abbreviated name
adjacentCellIdMCC
Managed object
ADCE
Multiplicity
1
Table 41
DN9813866
Reference Cell LAC (Cont.)
MCC
Id:0900d8058089b04f
Confidential
109
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the MCC of the adjacent
cell (target cell). The identification consists of the Mobile
Country Code Number, Mobile Network Code Number,
Cell Identification and the Location Area Code.
NOTE:
MML Range: 0..999
MML modification: Online
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
MCC value of serving cell
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
adjacentCellIdMNC of ADCE - If this parameter is given
then the parameter MNC is obligatory.
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
EAC, EAD, EAM, EAX, EAO, EAT, EAP
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 41
3.37
mobile country code of reference cell (MCC1-MCC5)
Parameter name
Reference Cell MCC
Abbreviated name
adjIdMCC
Managed object
ADCE
Table 42
110
MCC (Cont.)
Reference Cell MCC
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Multiplicity
1
Description
With these parameters you define the Mobile Country
Code of the reference cell.
NOTE:
MML range: 0..999
MML default: MCC value of serving cell
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
MCC value of serving cell
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
C/I Based Handover Candidate Evaluation (18)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EAX, EAO
MML Abbreviated Name
MCC1-MCC5
MML Full Name
mobile country code of reference cell
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 42
3.38
mobile network code (MNC)
Parameter name
MNC
Abbreviated name
adjacentCellIdMNC
Managed object
ADCE
Table 43
DN9813866
Reference Cell MCC (Cont.)
MNC
Id:0900d8058089b04f
Confidential
111
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Multiplicity
1
Description
With this parameter you define the MNC of the adjacent
cell (target cell). The identification consists of the Mobile
Country Code Number, Mobile Network Code Number,
Cell Identification and the Location Area Code.
NOTE:
MML range: 0..999
MML modification: Online
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376 , 708, 722 or 732
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
MNC value of serving cell
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
adjacentCellIdMCC of ADCE - If this parameter is given
then the parameter MCC is obligatory.
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
EAC, EAD, EAM, EAX, EAO, EAT, EAP
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 43
112
MNC (Cont.)
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
3.39
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
mobile network code of reference cell (MNC1-MNC5)
Parameter name
Reference Cell MNC
Abbreviated name
adjIdMNC
Managed object
ADCE
Multiplicity
1
Description
With these parameters you define the Mobile Network
Code of the reference cell.
NOTE:
MML range: 0...999
MML default: MNC value of serving cell
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
MNC value of serving cell
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
C/I Based Handover Candidate Evaluation (18)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EAX, EAO
MML Abbreviated Name
MNC1-MNC5
MML Full Name
mobile network code of reference cell
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 44
DN9813866
Reference Cell MNC
Id:0900d8058089b04f
Confidential
113
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
3.40
BSS Radio Network Parameter Dictionary
MS pwr opt level (POPT)
Parameter name
MS Pwr Opt Level
Abbreviated name
msPwrOptLevel
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the optimum uplink
RF signal level after a handover on a channel in the
adjacent cell. If optimisation is enabled, the parameter indicates also the desirable uplink signal level
after the handover. The optimisation procedure
works only for intra-BSC handovers. The BSC
presumes that the uplink signal level and the
downlink signal level are in balance within the
coverage area of the adjacent cell. If the downlink
signal is, for example, 5 dB stronger than the uplink
signal, set the value for this parameter 5dB higher
than the desirable uplink signal level.
MML NOTE:
Range: -110..-47 (dBm), N (no optimisation (255))
Default: N
Additional information
-
Range
-110...-47
Step
1
Unit
dBm
Formula for getting
internal value
internal_value = (gui_value + 110)
Default value
255 dBm
Default value notes
-
Required on Creation
optional
Special value
Not used (255)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Feature dependencies
-
Table 45
114
Optimization Of The MS Power Level In Handovers (13)
MS Pwr Opt Level
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Interfaces
•
•
•
•
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
POPT
MML Full Name
MS pwr opt level
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 45
3.41
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
MS Pwr Opt Level (Cont.)
MS TX pwr max gsm (PMAX1)
Parameter name
MS Tx Pwr Max GSM
Abbreviated name
msTxPwrMaxGSM
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the maximum transmission power of the MS for each adjacent cell. This parameter replaces old ms_txpwr_max_cell parameter.
NOTE:
MML Modification: Online
Additional information
-
Range
5...39
Step
2
Unit
dBm
Formula for getting internal
value
internal_value = (gui_value - 43) / -2
Default value
33 dBm
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Table 46
DN9813866
MS Tx Pwr Max GSM
Id:0900d8058089b04f
Confidential
115
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Related options
-
Related features
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 45.008
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
PMAX1
MML Full Name
MS TX pwr max gsm
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 46
3.42
MS Tx Pwr Max GSM (Cont.)
MS TX pwr max gsm1x00 (PMAX2)
Parameter name
MS Tx Pwr Max GSM1x00
Abbreviated name
msTxPwrMaxGSM1x00
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the maximum transmission power of the MS for each adjacent cell.
NOTE: MML value range:
GSM 1800: 0..36 dBm (step size 2)
GSM 1900: 0..32 dBm (step size 2) and 33 dBm
NOTE:
MML modification: Online
NOTE: NetAct internal value range:
GSM 1800:
0..30 dBm: 0..15 (UI value - 30)/-2
32 dBm: 31
34 dBm: 30
36 dBm: 29
GSM 1900:
0..30 dBm: 0..15 (UI value - 30)/-2
32 dBm: 31
33 dBm: 30
Additional information
-
Range
0...36
Step
2
Unit
-
Table 47
116
MS Tx Pwr Max GSM1x00
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Formula for getting internal
value
internal_value = gui_value
Default value
30
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 45.008
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
PMAX2
MML Full Name
MS TX pwr max gsm1x00
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 47
3.43
MS Tx Pwr Max GSM1x00 (Cont.)
NCCR and DTM EGPRS PBGT margin (EPM)
Parameter name
NCCR And DTM EGPRS PBGT Margin
Abbreviated name
nccrEgprsPbgtMargin
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the threshold which is
used for EGPRS and DTM MSS as a power budget
margin in the NCCR and DTM power budget process.
Note: This parameter does not require EGPRS option.
Additional information
-
Range
-63...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = (gui_value + 63)
Default value
6 dB
Table 48
DN9813866
NCCR And DTM EGPRS PBGT Margin
Id:0900d8058089b04f
Confidential
117
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85) (optional) OR Dual
Transfer Mode and Statistics (DTM) (91) (optional)
Related features
•
•
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
BSS20394: Network Controlled Cell Re-selection
BSS20088: Dual Transfer Mode (DTM)
•
•
RAC <-> RACApp
RAC <-> BSC
Interfaces
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
EPM
MML Full Name
NCCR and DTM EGPRS PBGT margin
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 48
3.44
NCCR and DTM GPRS PBGT margin (GPM)
Parameter name
NCCR And DTM GPRS PBGT Margin
Abbreviated name
nccrGprsPbgtMargin
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the threshold which is
used for GPRS and DTM MSS as a power budget margin
in the NCCR and DTM power budget process.
Additional information
-
Range
-63...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = (gui_value + 63)
Table 49
118
NCCR And DTM EGPRS PBGT Margin (Cont.)
NCCR And DTM GPRS PBGT Margin
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Default value
6 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85) (optional) OR Dual
Transfer Mode and Statistics (DTM) (91) (optional)
Related features
•
•
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
BSS20394: Network Controlled Cell Re-selection
BSS20088: Dual Transfer Mode (DTM)
•
•
RAC <-> RACApp
RAC <-> BSC
Interfaces
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
GPM
MML Full Name
NCCR and DTM GPRS PBGT margin
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 49
3.45
NCCR And DTM GPRS PBGT Margin (Cont.)
NCCR EGPRS quality margin (EQM)
Parameter name
NCCR EGPRS Quality Margin
Abbreviated name
nccrEgprsQualityMargin
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the margin for EGPRS MS
by which the signal level of the neighbor cell must exceed
the signal level of the serving cell before the cell reselection is possible.
Note: This parameter does not require EGPRS option.
Additional information
-
Range
-5...5
Step
1
Unit
dB
Table 50
DN9813866
NCCR EGPRS Quality Margin
Id:0900d8058089b04f
Confidential
119
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
Formula for getting internal
value
internal_value = (gui_value + 5)
Default value
0 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85)
Related features
•
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
BSS20394: Network Controlled Cell Re-selection
•
•
RAC <-> RACApp
RAC <-> BSC
Interfaces
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
EQM
MML Full Name
NCCR EGPRS quality margin
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 50
3.46
NCCR GPRS quality margin (GQM)
Parameter name
NCCR GPRS Quality Margin
Abbreviated name
nccrGprsQualityMargin
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the margin for GPRS MS
by which the signal level of the neighbor cell must exceed
the signal level of the serving cell before the cell reselection is possible.
Additional information
-
Range
-5...5
Step
1
Unit
dB
Table 51
120
NCCR EGPRS Quality Margin (Cont.)
NCCR GPRS Quality Margin
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Formula for getting internal
value
internal_value = (gui_value + 5)
Default value
0 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85)
Related features
•
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
BSS20394: Network Controlled Cell Re-selection
•
•
RAC <-> RACApp
RAC <-> BSC
Interfaces
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
GQM
MML Full Name
NCCR GPRS quality margin
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 51
3.47
network colour code (NCC)
Parameter name
BSIC NCC
Abbreviated name
adjCellBsicNcc
Managed object
ADCE
Multiplicity
1
Table 52
DN9813866
NCCR GPRS Quality Margin (Cont.)
BSIC NCC
Id:0900d8058089b04f
Confidential
121
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the network colour code
number.
NOTE:
The BSIC parameter, which is used to identify the BTS, is
composed of the NCC and BCC parameters. BSIC must
be equal to the BSIC parameter of adjacent BTS.
MML NOTE:
MML Modification: online
This parameter is mandatory in creation if the adjacent
cell and the BTS are not under the same BSS.
Additional information
-
Range
0...7
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
•
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
3GPP Reference: 44.018
MML Commands
EAC, EAM, EAO, EAP
MML Abbreviated Name
NCC
MML Full Name
network colour code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 52
122
BSIC NCC (Cont.)
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
3.48
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
priority class (PRC)
Parameter name
Priority Class
Abbreviated name
hcsPriorityClass
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the HCS (hierarchical cell
structures) priority for the cells. 0 is the lowest and 7 is the
highest priority. In the adjacent cell creation, if this parameter is not given and the SEG and the adjacent cell are in
the same BSS, the value of this parameter is copied from
the SEG.
NOTE:
MML Modification: Online
Additional information
-
Range
0...7
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 44.060
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
PRC
MML Full Name
priority class
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 53
DN9813866
Priority Class
Id:0900d8058089b04f
Confidential
123
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
3.49
BSS Radio Network Parameter Dictionary
reporting priority (REP)
Parameter name
Reporting Priority
Abbreviated name
reportingPriority
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the reporting priority of the
adjacent GSM cell.
Additional information
-
Range
Reporting Priority Is Set To Normal (0), Reporting Priority
Is Set To High (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Reporting Priority Is Set To Normal ==> 0
Reporting Priority Is Set To High ==> 1
Default value
Reporting Priority Is Set To Normal (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
Support For Enhanced Measurement Report (EMR)
(67)
-
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 44.018, 45.008
MML Commands
EAC, EAM, EAO, EAP
MML Abbreviated Name
REP
MML Full Name
reporting priority
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 54
124
Reporting Priority
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
3.50
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
routing area code (RAC)
Parameter name
RAC
Abbreviated name
rac
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the routing area code in
the adjacent cell.
NOTE:
MML description: In the adjacent cell creation, if this
parameter is not given and the SEG and the adjacent cell
are in the same BSS, the value of this parameter is
copied from the SEG.
NOTE:
MML modification: Online
Additional information
-
Range
0...255
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
255
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 44.060
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
RAC
MML Full Name
routing area code
Segment Level Parameter
-
Table 55
DN9813866
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
RAC
Id:0900d8058089b04f
Confidential
125
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 55
3.51
RAC (Cont.)
RX lev min cell (SL)
Parameter name
RX Lev Min Cell
Abbreviated name
rxLevMinCell
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the minimum signal level
of an adjacent cell, when a handover is allowed to one of
them.
Additional information
-
Range
-110...-47
Step
1
Unit
dBm
Formula for getting internal
value
internal_value = (gui_value + 110)
Default value
-100 dBm
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
SL
MML Full Name
RX lev min cell
Segment Level Parameter
-
Table 56
126
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
RX Lev Min Cell
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
File Based Provisioning sup- true
ported
Table 56
3.52
RX Lev Min Cell (Cont.)
synchronised (SYNC)
Parameter name
Synchronised
Abbreviated name
synchronized
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define whether the adjacent cell
is synchronised with the cell in use. When defining adjacencies between the sectors of PrimeSite, the value of
parameter synchronised must be N (not synchronised).
This is because the sectors of PrimeSite are not synchronised with each other in a fault case, when the system
has set the sectors to minimum configuration.
Additional information
-
Range
not synchronized (N) (0), synchronized (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
not synchronized (N) ==> 0
synchronized (Y) ==> 1
Default value
not synchronized (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
3GPP Reference: 44.018
MML Commands
Table 57
DN9813866
EAC, EAM, EAO
Synchronised
Id:0900d8058089b04f
Confidential
127
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
MML Abbreviated Name
SYNC
MML Full Name
synchronised
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 57
3.53
Synchronised (Cont.)
target cell of direct access to desired layer (DADL)
Parameter name
Target Cell Of Direct Access To Desired Layer
Abbreviated name
dadlbTargetCell
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define whether the direct access
to desired layer/band handover is applied to the adjacent
cell.
Additional information
-
Range
DADL is not applied (N) (0), DADL is applied (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
DADL is not applied (N) ==> 0
DADL is applied (Y) ==> 1
Default value
DADL is not applied (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
Direct Access To Desired Layer/Band (35)
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EAC, EAM, EAO
Table 58
128
•
Target Cell Of Direct Access To Desired Layer
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
MML Abbreviated Name
DADL
MML Full Name
target cell of direct access to desired layer
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 58
3.54
Target Cell Of Direct Access To Desired Layer (Cont.)
TRHO target level (TRHO)
Parameter name
TRHO Target Level
Abbreviated name
trhoTargetLevel
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the minimum signal level
when a traffic reason handover is allowed to an adjacent
cell.
NOTE:
MML range: -109...-47 dBm and N (not in use)
Additional information
-
Range
-109...-47
Step
1
Unit
dBm
Formula for getting internal
value
internal_value = (gui_value + 110)
Default value
0 dBm
Default value notes
-
Required on Creation
optional
Special value
Not used (0)
Related functions
-
Modification
Online
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
Table 59
DN9813866
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
TRHO Target Level
Id:0900d8058089b04f
Confidential
129
Adjacent GSM Cell (ADJC/ADCE) radio network object
parameters
BSS Radio Network Parameter Dictionary
References
-
MML Commands
EAC, EAM, EAO
MML Abbreviated Name
TRHO
MML Full Name
TRHO target level
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 59
130
TRHO Target Level (Cont.)
Id:0900d8058089b04f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
4 Adjacent UTRAN Cell (UADJC/ADJW) radio
network object parameters
4.1
adjacent cell index (INDEX)
Parameter name
ADJW ID
Abbreviated name
id
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the adjacent cell index for
the adjacent UTRAN cell. The index value is unambiguous under a serving GSM cell.
MML NOTE: The smallest free index value for serving cell
is searched and used.
Additional information
-
Range
0...31
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EAE, EAH, EAI, EAG, EAF, EAJ, EAK, EAL
MML Abbreviated Name
INDEX
MML Full Name
adjacent cell index
Segment Level Parameter
-
Table 60
DN9813866
Inter System HO (ISHO Support In BSC) (56)
(optional) OR TD-SCDMA Interworking, Idle Mode
(113) (optional)
ADJW ID
Id:0900d8058089b050
Confidential
131
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 60
4.2
ADJW ID (Cont.)
cell identification (CI)
Parameter name
Cell Identification
Abbreviated name
AdjwCId
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the cell number for the
adjacent UTRAN cell.
Additional information
-
Range
0...65535
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
Inter System HO (ISHO Support In BSC) (56)
(optional) OR TD-SCDMA Interworking, Idle Mode
(113) OR Fast return from TD-SCDMA to GSM (173)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 23.003, 25.413, 48.008
MML Commands
EAE, EAH, EAI, EAF, EAJ, EAK, EAL
MML Abbreviated Name
CI
MML Full Name
cell identification
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 61
132
Cell Identification
Id:0900d8058089b050
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
4.3
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
cell parameter (CPA)
Parameter name
Cell Parameter
Abbreviated name
cellParameter
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the downlink cell parameter of the primary common pilot channel of the adjacent
TD-SCDMA RAN cell.
NOTE: Special value 255 defines that the adjacent cell is
a UTRAN cell.
Additional information
-
Range
0...127
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
Optional
Special value
Parameter not used. This is an adjacent UTRAN cell
(255)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
scramblingCode of ADJW - If Scrambling Code parameter value is other than 65535 the Cell Parameter value is
initialized to 255.
Parameter relationships
-
Related options
•
TD-SCDMA Interworking, Idle Mode (113) OR Fast
return from TD-SCDMA to GSM (173)
Related features
•
BSS30320: TD-SCDMA Interworking, Idle Mode
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
•
3GPP Reference: 25.213, 44.018
Nokia reference: BSS21207: GSM-TDSCDMA Handover.
MML Commands
EAF, EAK, EAL
MML Abbreviated Name
CPA
MML Full Name
cell parameter
Segment Level Parameter
-
Table 62
DN9813866
Cell Parameter
Id:0900d8058089b050
Confidential
133
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 62
4.4
Cell Parameter (Cont.)
direct access Ec/Io threshold (DET)
Parameter name
Direct Access Ec/Io Threshold
Abbreviated name
intSystemDaEcioThr
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the minimum CPICH Ec/Io
level of an adjacent WCDMA RAN cell in decibels, when
a direct access to the adjacent WCDMA RAN cell is
allowed. If this parameter has the value 0.5 dB, the BSC
is not allowed to initiate a direct access from the serving
GSM cell to the WCDMA RAN cell because a CPICH
Ec/Io level measured by mobiles can be maximum 0 dB.
Additional information
-
Range
-24...0.5
Step
0.5
Unit
dB
Formula for getting internal
value
internal_value = (gui_value + 24) * 2
Default value
-11.5 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
Inter System HO (ISHO Support In BSC) (56)
-
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
3GPP Reference: 25.133
MML Commands
EAE, EAH, EAI
MML Abbreviated Name
DET
MML Full Name
direct access Ec/Io threshold
Segment Level Parameter
-
Table 63
134
•
Direct Access Ec/Io Threshold
Id:0900d8058089b050
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
File Based Provisioning sup- true
ported
Table 63
4.5
Direct Access Ec/Io Threshold (Cont.)
downlink transmission diversity (DIV)
Parameter name
Downlink Transmission Diversity
Abbreviated name
txDiversityInd
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define whether the downlink
transmission diversity capability of the logical node that is
controlling the adjacent UTRAN cell is used or not.
Additional information
-
Range
not used (N) (0), used (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
not used (N) ==> 0
used (Y) ==> 1
Default value
not used (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
-
Interfaces
•
•
RAC <-> BSC
RACApp <-> RAC
References
•
3GPP Reference: 44.018, 44.060
MML Commands
EAE, EAH, EAI, EAF, EAK
MML Abbreviated Name
DIV
MML Full Name
downlink transmission diversity
Segment Level Parameter
-
Table 64
DN9813866
Inter System HO (ISHO Support In BSC) (56) OR
TD-SCDMA Interworking, Idle Mode (113) OR Fast
return from TD-SCDMA to GSM (173)
Downlink Transmission Diversity
Id:0900d8058089b050
Confidential
135
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 64
4.6
Downlink Transmission Diversity (Cont.)
ISNCCR quality threshold (FQT)
Parameter name
ISNCCR Quality Threshold
Abbreviated name
isnccrQualityThr
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the minimum signal
quality level of an adjacent WCDMA/TDSCDMA
RAN cell for an inter-system network-controlled cell
re-selection (ISNCCR).
Note: The value 0.5 dB of this parameter means
that the BSC is never allowed to initiate an ISNCCR
attempt from the serving cell towards the
WCDMA/TDSCDMA RAN cell because a CPICH
Ec/Io level measured by mobiles can be maximum
0 dB. Effects only in the GSM neighbours.
Additional information
-
Range
-24...0.5
Step
0.5
Unit
dB
Formula for getting
internal value
internal_value = (gui_value + 24) * 2
Default value
-15 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Table 65
136
Inter System HO (ISHO Support In BSC) (56)
(optional) AND NC Cell Re-selection (85)
(optional) AND ISNCCR Usage (86) (optional)
OR IS-NCCR for TD-SCDMA (171)
ISNCCR FDD Quality Threshold
Id:0900d8058089b050
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
•
Feature dependencies
•
BSS11112: Network Controlled Cell Reselection (NCCR)
BSS20394: Network Controlled Cell Re-selection
RG301736 IS-NCCR for TD-SCDMA
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EAE, EAH, EAI EAF, EAK, EAL
MML Abbreviated Name
FQT
MML Full Name
ISNCCR quality threshold
Segment Level Parameter
-
File Based Provisioning
supported
true
•
Table 65
4.7
location area code (LAC)
Parameter name
LAC
Abbreviated name
lac
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the location area that the
adjacent UTRAN cell belongs to.
Additional information
-
Range
1...65533
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
Not defined (65535)
Related functions
-
Modification
On-Line
Modified
-
Table 66
DN9813866
ISNCCR FDD Quality Threshold (Cont.)
LAC
Id:0900d8058089b050
Confidential
137
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
BSS Radio Network Parameter Dictionary
Related parameters
-
Parameter relationships
-
Related options
Related features
•
Inter System HO (ISHO Support In BSC) (56) OR
TD-SCDMA Interworking, Idle Mode (113) OR Fast
return from TD-SCDMA (173)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 23.003, 24.008, 44.018, 48.008
MML Commands
EAE, EAH, EAI, EAF, EAK
MML Abbreviated Name
LAC
MML Full Name
location area code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 66
4.8
LAC (Cont.)
minimum CPICH Ec/Io level (MET)
Parameter name
Minimum CPICH Ec/Io Level
Abbreviated name
minEcnoThreshold
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the minimum CPICH Ec/Io
level of an adjacent WCDMA RAN cell for an inter-system
handover attempt. The threshold level must be exceeded
before the BSC is allowed to trigger a handover attempt
towards the adjacent WCDMA RAN cell.
NOTE:
The value 0.5 dB of this parameter means that the BSC
is never allowed to initiate a handover attempt from the
serving GSM cell towards the WCDMA RAN cell because
a CPICH Ec/Io level measured by mobiles can be
maximum 0 dB.
Additional information
-
Range
-24...0.5
Step
0.5
Unit
dB
Formula for getting internal
value
internal_value = (gui_value + 24) * 2
Default value
-15 dB
Default value notes
-
Table 67
138
Minimum CPICH Ec/Io Level
Id:0900d8058089b050
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
Inter System HO (ISHO Support In BSC) (56)
-
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 25.133
MML Commands
EAE, EAH, EAI
MML Abbreviated Name
MET
MML Full Name
minimum CPICH Ec/Io level
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 67
4.9
Minimum CPICH Ec/Io Level (Cont.)
mobile country code (MCC)
Parameter name
MCC
Abbreviated name
mcc
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the mobile country code
number for the adjacent UTRAN cell.
NOTE:
MML range: 0...999
MML default: MCC value of the serving GSM cell
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
Default value is the MCC value of serving cell.
Table 68
DN9813866
MCC
Id:0900d8058089b050
Confidential
139
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
BSS Radio Network Parameter Dictionary
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
mnc of ADJW - If this parameter is given then the parameter MNC in obligatory.
Parameter relationships
-
Related options
Related features
•
•
•
Inter System HO (ISHO Support In BSC) (56) OR
TD-SCDMA Interworking, Idle Mode (113) OR
Fast return from TD-SCDMA to GSM (173)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 23.003, 24.008, 44.018, 48.008
MML Commands
EAE, EAH, EAI, EAF, EAJ, EAK, EAL
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 68
4.10
MCC (Cont.)
mobile network code (MNC)
Parameter name
MNC
Abbreviated name
mnc
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the mobile network code
number for the adjacent UTRAN cell.
NOTE:
MML range: 0..99
0..999
MML default: MNC value of the serving GSM cell
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
Additional information
-
Range
2...3
Step
-
Table 69
140
MNC
Id:0900d8058089b050
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
Default value is the MNC value of the serving GSM cell
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
mcc of ADJW - If this parameter is given then the parameter MCC in obligatory.
Parameter relationships
-
•
•
•
Related options
Related features
Inter System HO (ISHO Support In BSC) (56)
TD-SCDMA Interworking, Idle Mode (113)
Fast return from TD-SCDMA to GSM (173)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 23.003, 24.008, 44.018, 48.008
MML Commands
EAE, EAH, EAI, EAF, EAJ, EAK, EAL
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 69
4.11
radio network controller identifier (RNC)
Parameter name
RNC ID
Abbreviated name
rncId
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the radio network controller that controls the adjacent UTRAN cell on the UTRAN
network.
Additional information
-
Range
1...4095
Step
1
Unit
-
Table 70
DN9813866
MNC (Cont.)
RNC ID
Id:0900d8058089b050
Confidential
141
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
BSS Radio Network Parameter Dictionary
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
•
•
Inter System HO (ISHO Support In BSC) (56)
TD-SCDMA Interworking, Idle Mode (113)
Fast return from TD-SCDMA to GSM (173)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 23.003, 25.003, 48.008
MML Commands
EAE, EAH, EAI, EAF, EAJ, EAK, EAL
MML Abbreviated Name
RNC
MML Full Name
radio network controller identifier
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 70
4.12
reporting priority (REP)
Parameter name
Reporting Priority
Abbreviated name
reportingPriority
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the reporting priority of the
adjacent UTRAN cell.
Additional information
-
Range
Reporting Priority Is Set To Normal (0), Reporting Priority
Is Set To High (1)
Step
-
Unit
-
Table 71
142
RNC ID (Cont.)
Reporting Priority
Id:0900d8058089b050
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
Formula for getting internal
value
gui ==> internal
Reporting Priority Is Set To Normal ==> 0
Reporting Priority Is Set To High ==> 1
Default value
Reporting Priority Is Set To Normal (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
Inter System HO (ISHO Support In BSC) (56) OR
Fast Return to TD-SCDMA(173)
-
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
3GPP Reference: 44.018, 45.008
MML Commands
EAE, EAH, EAI, EAF, EAK, EAL
MML Abbreviated Name
REP
MML Full Name
reporting priority
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 71
4.13
Reporting Priority (Cont.)
scrambling code (SCC)
Parameter name
Scrambling Code
Abbreviated name
scramblingCode
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the downlink scrambling code of the primary common pilot channel of
the adjacent UTRAN cell.
NOTE: Special value 65535 is reserved for TDSCDMA Interworking -feature to define that the
adjacent cell is a TD-SCDMA RAN cell. Scrambling
codes are not used in TDD (Time Division Duplex)
type of UTRAN.
Table 72
DN9813866
Scrambling Code
Id:0900d8058089b050
Confidential
143
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
Additional information
-
Range
0...511
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
SCR not used, this is an adjacent TD-SCDMA cell
(65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
cellParameter of ADJW - If Cell Parameter parameter value is other than 255 the Scrambling Code
value is initialized to 65535.
Parameter relationships
-
Related options
•
Feature dependencies
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 24.008, 44.018, 44.060
MML Commands
EAE, EAH, EAI
MML Abbreviated Name
SCC
MML Full Name
scrambling code
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 72
4.14
Inter System HO (ISHO Support In BSC) (56)
Scrambling Code (Cont.)
service area code (SAC)
Parameter name
Service Area Code
Abbreviated name
sac
Managed object
ADJW
Multiplicity
1
Table 73
144
BSS Radio Network Parameter Dictionary
Service Area Code
Id:0900d8058089b050
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
Description
With this parameter you define the service area the
adjacent UTRAN cell belongs to.
Additional information
-
Range
0...65535
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
Inter System HO (ISHO Support In BSC) (56) OR
TD-SCDMA Interworking, Idle Mode (113) OR Fast
return from TD-SCDMA to GSM (173)
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 23.003, 25.413, 48.008
MML Commands
EAE, EAH, EAI, EAF, EAK
MML Abbreviated Name
SAC
MML Full Name
service area code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 73
4.15
synchronisation case (SC)
Parameter name
Synchronisation Case
Abbreviated name
syncCase
Managed object
ADJW
Multiplicity
1
Description
With this parameter you define the adjacent TD-SCDMA
RAN cell synchronisation case
Additional information
-
Table 74
DN9813866
Service Area Code (Cont.)
Synchronisation Case
Id:0900d8058089b050
Confidential
145
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
BSS Radio Network Parameter Dictionary
Range
Synchronisation case 1 is used (0), Synchronisation case
2 is used (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Synchronisation case 1 is used ==> 0
Synchronisation case 2 is used ==> 1
Default value
Synchronisation case 1 is used (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
•
TD-SCDMA Interworking, Idle Mode (113)
Fast return from TD-SCDMA to GSM (173)
Related features
•
BSS30320: TD-SCDMA Interworking, Idle Mode
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
3GPP Reference: 25.304
MML Commands
EAF, EAK, EAL
MML Abbreviated Name
SC
MML Full Name
synchronisation case
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 74
4.16
WCDMA downlink carrier frequency (FREQ)
Parameter name
WCDMA Downlink Carrier Frequency
Abbreviated name
uarfcn
Managed object
ADJW
Multiplicity
1
Table 75
146
Synchronisation Case (Cont.)
WCDMA Downlink Carrier Frequency
Id:0900d8058089b050
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Description
With this parameter you define the downlink carrier
frequency of the adjacent UTRAN cell. The frequency must be given as the UTRAN Absolute
Radio Frequency Channel Number (UARFCN).
Additional information
-
Range
0...16383
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Feature dependencies
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 24.008, 25.101, 25.331,
44.018, 44.060
MML Commands
EAE, EAH, EAI, EAF, EAK
MML Abbreviated Name
FREQ
MML Full Name
WCDMA downlink carrier frequency
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 75
DN9813866
Adjacent UTRAN Cell (UADJC/ADJW) radio network
object parameters
Inter System HO (ISHO Support In BSC) (56)
OR TD-SCDMA Interworking, Idle Mode (113)
OR Fast return from TD-SCDMA to GSM (173)
WCDMA Downlink Carrier Frequency (Cont.)
Id:0900d8058089b050
Confidential
147
Authorised Network (ANE) radio network object parameters
BSS Radio Network Parameter Dictionary
5 Authorised Network (ANE) radio network
object parameters
5.1
authorised networks identification (ANE)
Parameter name
ANE ID
Abbreviated name
aneId
Managed object
ANE
Multiplicity
1
Description
With this parameter you define a unique identifier number
for Authorised Networks.
Additional information
-
Range
1...10
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
IBHO (IMSI Based Handover) in BSC (80)
Related features
•
BSS12158: IMSI Based Handover
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
E4C, E4D, E4M, E4O
MML Abbreviated Name
ANE
MML Full Name
authorised networks identification
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 76
148
ANE ID
Id:0900d8058089b05b
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
5.2
Authorised Network (ANE) radio network object parameters
authorised networks name (NAME)
Parameter name
Authorised Networks Name
Abbreviated name
aneName
Managed object
ANE
Multiplicity
1
Description
With this parameter you define a unique name for a group
of Authorised Networks.
Note: This is defined as like "BTS name". Input of both
numeric and alphabetic characters is possible.
Additional information
-
Range
1...15
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
IBHO (IMSI Based Handover) in BSC (80)
Related features
•
BSS12158: IMSI Based Handover
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
E4C, E4D, E4M, E4O, E4S
MML Abbreviated Name
NAME
MML Full Name
authorised networks name
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 77
DN9813866
Authorised Networks Name
Id:0900d8058089b05b
Confidential
149
Authorised Network (ANE) radio network object parameters
5.3
BSS Radio Network Parameter Dictionary
network mobile country code (MCC1...6)
Parameter name
Network MCC
Abbreviated name
networkMCC
Managed object
ANE
Multiplicity
1
Description
With this parameter you define the Mobile Country Code
of an Authorised Network.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
networkMNC of ANE - If parameter is given then parameter Network MNC is obligatory, networkTechnology of
ANE - If parameter is given then parameter Network
Technology is obligatory.
Parameter relationships
-
Related options
•
IBHO (IMSI Based Handover) in BSC (80)
Related features
•
BSS12158: IMSI Based Handover
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
E4C, E4M, E4O
MML Abbreviated Name
MCC1...6
MML Full Name
network mobile country code
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 78
150
Network MCC
Id:0900d8058089b05b
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
5.4
Authorised Network (ANE) radio network object parameters
network mobile network code (MNC1...6)
Parameter name
Network MNC
Abbreviated name
networkMNC
Managed object
ANE
Multiplicity
1
Description
With this parameter you define the Mobile Network
Code of an Authorised Network.
NOTE:
If single-digit MNC is given, the preceding digits will
have value 0xF which means "not defined"
If 2-digit MNC is given, the preceding digit will have
value 0xF which means "not defined"
3-digit MNC is stored such as it has been given
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
networkMCC of ANE - If parameter is given then
parameter Network MCC is obligatory.
networkTechnology of ANE - If parameter is given
then parameter Network Technology is obligatory.
Parameter relationships
-
Related options
•
IBHO (IMSI Based Handover) in BSC (80)
Feature dependencies
•
BSS12158: IMSI Based Handover
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
Table 79
DN9813866
Network MNC
Id:0900d8058089b05b
Confidential
151
Authorised Network (ANE) radio network object parameters
References
-
MML Commands
E4C, E4M, E4O
MML Abbreviated Name
MNC1...6
MML Full Name
network mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 79
5.5
BSS Radio Network Parameter Dictionary
Network MNC (Cont.)
network technology (TECH1...6)
Parameter name
Network Technology
Abbreviated name
networkTechnology
Managed object
ANE
Multiplicity
1
Description
With this parameter you define the technology which is
used within the authorised network in the Authorised
Networks group.
MML NOTE:
IBHO licence (parameter values 1 and 2 requires
ISHO_SUPPORT_IN_BSC (FIFILE option) addition to
IBHO licence)
Additional information
-
Range
GSM (0), WCDMA RAN (1), Both GSM And WCDMA
RAN (2)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
GSM ==> 0
WCDMA RAN ==> 1
Both GSM And WCDMA RAN ==> 2
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Table 80
152
Network Technology
Id:0900d8058089b05b
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Authorised Network (ANE) radio network object parameters
Related parameters
networkMCC of ANE - If parameter is given then parameter Network MCC is obligatory, networkMNC of ANE - If
parameter is given then parameter Network MNC is obligatory.
Parameter relationships
-
Related options
•
IBHO (IMSI Based Handover) in BSC (80)
Related features
•
BSS12158: IMSI Based Handover
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
E4C, E4M, E4O
MML Abbreviated Name
TECH1...6
MML Full Name
network technology
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 80
DN9813866
Network Technology (Cont.)
Id:0900d8058089b05b
Confidential
153
Adjacent LTE Cell (ADJL) radio network object parameters
BSS Radio Network Parameter Dictionary
6 Adjacent LTE Cell (ADJL) radio network
object parameters
6.1
barred LTE adjacent cell group (LTEBCG)
Parameter name
Barred LTE Adjacent Cell Group
Abbreviated name
barredLteAdjCellGroup
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define a bit pattern (6 bits)
where each bit corresponds the range of PCID
values which are not allowed when bit is set 1.
MML RANGE:
0: not used
1: PCIDs 0-83
2: PCIDs 84-167
4: PCIDs PCIDs 168-251
8: PCIDs 252-335
16: PCIDs 336-419
32: PCIDs 420-503
MML NOTE: You can give 0 or 1-6 values at the
same time by using the wild card character &.
MML default: 0
Additional information
-
Range
Bit 0: PCIDs 0-83, Bit 1: PCIDs 84-167, Bit 2: PCIDs
168- 251, Bit 3: PCIDs 252-335, Bit 4: PCIDs 336419, Bit 5: PCIDs 420-503
Step
-
Unit
-
Formula for getting
internal value
-
Default value
0
Default value notes
No PCID groups is barred
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Table 81
154
Barred LTE Adjacent Cell Group
Id:0900d8058089b05c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTEBCG
MML Full Name
barred LTE adjacent cell group
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 81
6.2
Barred LTE Adjacent Cell Group (Cont.)
barred LTE adjacent cell list (LTEBCL)
Parameter name
Barred LTE Adjacent Cell List
Abbreviated name
barredLteAdjCellList
Managed object
ADJL
Multiplicity
16
Description
With this parameter you define a list which contains
LTE physical layer adjacent cell identities (PCID’s)
which are not allowed to make cell reselection to.
List shall contain 16 cells at maximum.
Additional information
-
Range
0...503
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Table 82
DN9813866
Adjacent LTE Cell (ADJL) radio network object parameters
Barred LTE Adjacent Cell List
Id:0900d8058089b05c
Confidential
155
Adjacent LTE Cell (ADJL) radio network object parameters
BSS Radio Network Parameter Dictionary
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTEBCL
MML Full Name
barred LTE adjacent cell list
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 82
6.3
barred LTE adjacent cell pattern (LTEBCP)
Parameter name
Barred LTE Adjacent Cell Pattern
Abbreviated name
barredLteAdjCellPattern
Managed object
ADJL
Multiplicity
1
Description
Defines a bit pattern which corresponds to PCID
most significant bits. PCID and bit pattern is compared.
Additional information
-
Range
0...127
Step
1
Unit
bits
Formula for getting
internal value
internal_value = gui_value
Default value
255
Table 83
156
Barred LTE Adjacent Cell List (Cont.)
Barred LTE Adjacent Cell Pattern
Id:0900d8058089b05c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent LTE Cell (ADJL) radio network object parameters
Default value notes
Not used
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTEBCP
MML Full Name
barred LTE adjacent cell pattern
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 83
6.4
barred LTE adjacent cell pattern sense (LTEPS)
Parameter name
Barred LTE Adjacent Cell Pattern Sense
Abbreviated name
barredLteAdjCellPatternSense
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define the sense of the
given Barred LTE cell pattern and actual PCID.
Given bit pattern is compared either to be equal or
not equal with actual PCID according to this parameter.
Additional information
-
Range
Equal (0), Not equal (1)
Table 84
DN9813866
Barred LTE Adjacent Cell Pattern (Cont.)
Barred LTE Adjacent Cell Pattern Sense
Id:0900d8058089b05c
Confidential
157
Adjacent LTE Cell (ADJL) radio network object parameters
BSS Radio Network Parameter Dictionary
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Equal ==> 0
Not equal ==> 1
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTEPS
MML Full Name
barred LTE adjacent cell pattern sense
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 84
6.5
LTE cell downlink carrier frequency (FREQ)
Parameter name
LTE Adjacent Cell Downlink Carrier Frequency
Abbreviated name
earfcn
Managed object
ADJL
Multiplicity
1
Table 85
158
Barred LTE Adjacent Cell Pattern Sense (Cont.)
LTE Adjacent Cell Downlink Carrier Frequency
Id:0900d8058089b05c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent LTE Cell (ADJL) radio network object parameters
Description
With this parameter you define the downlink carrier
frequency of the adjacent LTE cell. The frequency
must be given as the LTE Absolute Radio Frequency Channel Number (EARFCN).
Additional information
-
Range
0...29649
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
FREQ
MML Full Name
LTE cell downlink carrier frequency
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 85
DN9813866
LTE Adjacent Cell Downlink Carrier Frequency (Cont.)
Id:0900d8058089b05c
Confidential
159
Adjacent LTE Cell (ADJL) radio network object parameters
6.6
LTE adjacent cell index (INDEX)
Parameter name
LTE Adjacent Cell Index
Abbreviated name
lteAdjCellIndex
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define the adjacent cell
index for the adjacent LTE cell. The index value is
unambiguous under a serving GSM cell.
Additional information
-
Range
0...254
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
INDEX
MML Full Name
LTE adjacent cell index
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 86
160
BSS Radio Network Parameter Dictionary
LTE Adjacent Cell Index
Id:0900d8058089b05c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
6.7
Adjacent LTE Cell (ADJL) radio network object parameters
LTE adjacent cell mobile country code (MCC)
Parameter name
LTE Adjacent Cell Mobile Country Code
Abbreviated name
lteAdjCellMcc
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define the mobile country
code number for the LTE adjacent cell.
MML range: 0...999
MML default: MCC value of the serving GSM cell
When this parameter is given the MCC parameter
is mandatory.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
Default value is the MCC value of serving cell.
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
MCC
MML Full Name
LTE adjacent cell mobile country code
Segment Level Parameter
-
Table 87
DN9813866
LTE Adjacent Cell Mobile Country Code
Id:0900d8058089b05c
Confidential
161
Adjacent LTE Cell (ADJL) radio network object parameters
File Based Provisioning
supported
Table 87
6.8
BSS Radio Network Parameter Dictionary
true
LTE Adjacent Cell Mobile Country Code (Cont.)
LTE cell min bandwidth (LTEMB)
Parameter name
LTE Adjacent Cell Minimum Bandwidth
Abbreviated name
lteAdjCellMinBand
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define the minimum value
of the channel bandwidth for adjacent LTE cells on
given LTE cell ARFCN.
Additional information
-
Range
6 kHz (0), 15 kHz (1), 25 kHz (2), 50 kHz (3), 75 kHz
(4), 100 kHz (5)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
6 kHz ==> 0
15 kHz ==> 1
25 kHz ==> 2
50 kHz ==> 3
75 kHz ==> 4
100 kHz ==> 5
Default value
6 kHz (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Table 88
162
LTE Adjacent Cell Minimum Bandwidth
Id:0900d8058089b05c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent LTE Cell (ADJL) radio network object parameters
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTEMB
MML Full Name
LTE cell min bandwidth
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 88
6.9
LTE adjacent cell min RX level (LTERXM)
Parameter name
LTE Adjacent Cell Min RX Level
Abbreviated name
lteAdjCellMinRxLevel
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define the minimum RX
level for LTE. Value of this parameter must be
exceeded before MS can make a reselection
towards the adjacent LTE cell.
Additional information
-
Range
-140...-78
Step
2
Unit
dB
Formula for getting
internal value
internal_value = (gui_value + 140) / 2
Default value
-140 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Table 89
DN9813866
LTE Adjacent Cell Minimum Bandwidth (Cont.)
LTE Adjacent Cell Min RX Level
Id:0900d8058089b05c
Confidential
163
Adjacent LTE Cell (ADJL) radio network object parameters
BSS Radio Network Parameter Dictionary
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTERXM
MML Full Name
LTE adjacent cell min RX level
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 89
6.10
LTE Adjacent Cell Min RX Level (Cont.)
LTE adjacent cell mobile network code (MNC)
Parameter name
LTE Adjacent Cell Mobile Network Code
Abbreviated name
lteAdjCellMnc
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define the mobile network
code number for the LTE adjacent cell.
MML range: 0..99
0..999
MML default: MNC value of the serving GSM cell
When this parameter is given the MNC parameter
is mandatory.
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
Additional information
-
Range
2...3
Step
-
Unit
characters
Table 90
164
LTE Adjacent Cell Mobile Network Code
Id:0900d8058089b05c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
Default value is the MNC value of serving cell.
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
MNC
MML Full Name
LTE adjacent cell mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 90
6.11
LTE Adjacent Cell Mobile Network Code (Cont.)
LTE adjacent cell priority (LTECP)
Parameter name
LTE Adjacent Cell Priority
Abbreviated name
lteAdjCellPriority
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define an absolute priority
of the adjacent LTE cell. 0 is the lowest and 7 is the
highest priority.
Additional information
-
Range
0...7
Step
1
Table 91
DN9813866
Adjacent LTE Cell (ADJL) radio network object parameters
LTE Adjacent Cell Priority
Id:0900d8058089b05c
Confidential
165
Adjacent LTE Cell (ADJL) radio network object parameters
BSS Radio Network Parameter Dictionary
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTECP
MML Full Name
LTE adjacent cell priority
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 91
6.12
LTE adjacent cell reselection lower threshold (LTERLT)
Parameter name
LTE Adjacent Cell Reselection Lower Threshold
Abbreviated name
lteAdjCellReselectLowerThr
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define a minimum value for
cell reselection threshold for LTE adjacent cell
having lower priority than serving cell.
Table 92
166
LTE Adjacent Cell Priority (Cont.)
LTE Adjacent Cell Reselection Lower Threshold
Id:0900d8058089b05c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Adjacent LTE Cell (ADJL) radio network object parameters
Additional information
-
Range
0...62
Step
2
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
32 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
lteAdjCellReselectUpperThr of ADJL - , must have
equal or greather value than lteAdjCellReselectLowerThr.
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTERLT
MML Full Name
LTE adjacent cell reselection lower threshold
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 92
6.13
LTE adjacent cell reselection upper threshold (LTERUT)
Parameter name
LTE Adjacent Cell Reselection Upper Threshold
Abbreviated name
lteAdjCellReselectUpperThr
Table 93
DN9813866
LTE Adjacent Cell Reselection Lower Threshold (Cont.)
LTE Adjacent Cell Reselection Upper Threshold
Id:0900d8058089b05c
Confidential
167
Adjacent LTE Cell (ADJL) radio network object parameters
BSS Radio Network Parameter Dictionary
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define a minimum value for
cell reselection threshold for LTE adjacent cell
having higher priority than serving cell.
Additional information
-
Range
0...62
Step
2
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
32 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
lteAdjCellReselectLowerThr of ADJL - , must not
have greather value than lteAdjCellReselectUpperThr.
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
3GPP Reference: TS 36.104, TS 44.018, TS
45.008
•
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
LTERUT
MML Full Name
LTE adjacent cell reselection upper threshold
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 93
168
LTE Adjacent Cell Reselection Upper Threshold (Cont.)
Id:0900d8058089b05c
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
6.14
tracking area code (TAC)
Parameter name
LTE Adjacent Cell Tracking Area Code
Abbreviated name
lteAdjCellTac
Managed object
ADJL
Multiplicity
1
Description
With this parameter you define the identification of
the Tracking Area where the LTE adjacent cell
belongs to.
Additional information
-
Range
0...65535
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
LTE System Information (145)
Feature dependencies
•
BSS21353: LTE System Information
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
NSN reference: BSS21353: LTE System Information
MML Commands
EAN, EAS, EAU
MML Abbreviated Name
TAC
MML Full Name
tracking area code
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 94
DN9813866
Adjacent LTE Cell (ADJL) radio network object parameters
LTE Adjacent Cell Tracking Area Code
Id:0900d8058089b05c
Confidential
169
BCCH Allocation Frequency List (BA/BAL) radio network object parameters
BSS Radio Network Parameter Dictionary
7 BCCH Allocation Frequency List (BA/BAL)
radio network object parameters
7.1
frequency (-)
Parameter name
Frequency
Abbreviated name
frequency
Managed object
BAL
Multiplicity
32
Description
MML description:
With this parameter you define the frequency to be
added to the BCCH frequency list or to be removed
from it. The maximum number of frequencies in one
BCCH frequency list is 32.
NetAct description:
With this parameter you define the frequencies
belonging to the BCCH frequency list.
Range:
GSM 800: 128...251
GSM 900: 1...124 and 975...1023, 0
GSM 1800: 512...885
GSM 1900: 512...810
MULTI: 1...124, 128...251 <option>, 512...810
<option>, 512...885, 975...1023, 0
NOTE:
MULTI consists of three frequency bands, dual
band for GSM 900/ GSM 1800, dual band for GSM
800/GSM 1900 and dual band for GSM 800/GSM
1800. The value range of dual band GSM 900/
GSM 1800 is 1...124, 512...885, 975...1023, 0. The
value range of dual band GSM 800/GSM 1900 is
128...251, 512...810. The value range of dual band
GSM 800/ GSM 1800 is 128...251, 512...885. The
frequency range depends on the active dual band
feature. The maximum number of frequencies in
one BCCH frequency list is 32. If the Common
BCCH feature is used, the maximum is 31. If the
option ISHO Support In BSC is on, the maximum is
31. If the Common BCCH feature and also ISHO
Support In BSC option is used, the maximum is 30.
Additional information
Table 95
170
-
Frequency
Id:0900d8058089b05d
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Range
0...1023
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Feature dependencies
-
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 45.008
MML Commands
EBC, EBM, EBO
MML Abbreviated Name
-
MML Full Name
frequency
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 95
7.2
Double BCCH Allocation List (0)
Frequency (Cont.)
identification of BCCH frequency list (-)
Parameter name
BAL ID
Abbreviated name
id
Managed object
BAL
Multiplicity
1
Description
With this parameter you identify the BCCH frequency list.
Additional information
-
Table 96
DN9813866
BCCH Allocation Frequency List (BA/BAL) radio network object parameters
BAL ID
Id:0900d8058089b05d
Confidential
171
BCCH Allocation Frequency List (BA/BAL) radio network object parameters
Range
1...4400
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Double BCCH Allocation List (0)
Feature dependencies
•
BSS21149: Flexi BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EBC, EBD, EBM, EBO
MML Abbreviated Name
-
MML Full Name
identification of BCCH frequency list
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 96
7.3
BAL ID (Cont.)
type of BCCH frequency list (-)
Parameter name
Type Of BCCH Frequency List
Abbreviated name
frequencyBandInUse
Managed object
BAL
Multiplicity
1
Description
With this parameter you define the type of the BCCH frequency list. The value depends on the frequency band
used in the BTS. The band is either GSM 800, GSM 900,
GSM 1800, GSM 1900, or MULTI.
Table 97
172
BSS Radio Network Parameter Dictionary
Type Of BCCH Frequency List
Id:0900d8058089b05d
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
BCCH Allocation Frequency List (BA/BAL) radio network object parameters
Additional information
-
Range
GSM 900 (0), GSM 1800 (1), GSM 1900 (2), Multi Band
(3), GSM 800 (5)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
GSM 900 ==> 0
GSM 1800 ==> 1
GSM 1900 ==> 2
Multi Band ==> 3
GSM 800 ==> 5
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
Double BCCH Allocation List (0)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EBC, EBO
MML Abbreviated Name
-
MML Full Name
type of BCCH frequency list
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 97
DN9813866
Type Of BCCH Frequency List (Cont.)
Id:0900d8058089b05d
Confidential
173
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
8 Base Control Function (BCF) radio network
object parameters
8.1
Add BCF to chain / Remove BCF from chain (ADD / REM)
Parameter name
Slave BCF List
Abbreviated name
slaveBcfList
Managed object
BCF
Multiplicity
8
Description
With this parameter you define slave BCF(s) to the
chain under the master clock BCF.NOTE: The
parameter is only available for Talkfamily, MetroSite, UltraSite, Flexi EDGE, Flexi Multiradio, and
BTSplus.
MML NOTE:
ADD (MML Full Name: Add BCF to chain): The
slave BCF can be defined when creating or modifying the master clock BCF. If synchronisation of the
chain is enabled, the added BCF must be locked,
otherwise modification is online. Modification can
also be done in slave BCF creation.
REM (MML Full Name: remove BCF from chain):
The slave BCF can be removed when modifying the
master clock BCF. If synchronisation of the chain is
enabled, the removed BCF must be locked, othe
wise online.
Range:
MML default value: 0 (Not defined)
NetAct NOTE: If a master BCF and slave BCFs are
created to the BCF synchronisation chain in the
same RNW plan, the slave BCFs information has to
defined in the master BCF data.
Additional information
-
Range
1..4400
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
0
Default value notes
Not defined
Table 98
174
Slave BCF List
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Required on Creation
optional
Special value
Not defined (0)
Related functions
-
Modification
On-Line
Modified
When modifying a master clock BCF, the modification can be made online if synchronisation of the
chain is disabled. Requires locking of the slave
BCF(s), if synchronisation of the master clock BCF
is enabled (SENA=Y). When creating or removing
an independent mode BCF, the modification
requires BCF locking.
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
BSS21149: Flexi BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
MML Commands
EFC, EFM, EFO, EFL / EFM, EFO, EFL
MML Abbreviated Name
ADD / REM
MML Full Name
Add BCF to chain / Remove BCF from chain
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 98
8.2
Slave BCF List (Cont.)
administrative state (-)
Parameter name
Administrative State
Abbreviated name
adminState
Managed object
BCF
Multiplicity
1
Table 99
DN9813866
Base Control Function (BCF) radio network object parameters
Administrative State
Id:0900d8058089b05e
Confidential
175
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you lock or unlock the object. If the
BCF is in operational use, the administrative state must
be "unlocked". If the state is "locked", the BCF cannot
transfer traffic.
MML NOTE:
MML Range:
L (locked)
U (unlocked)
MML default: L
Additional information
-
Range
Unlocked (1), Locked (3)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Unlocked ==> 1
Locked ==> 3
Default value
Locked (3)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EFO, EFS, EEI
MML Abbreviated Name
-
MML Full Name
administrative state
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 99
176
Administrative State (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
8.3
Base Control Function (BCF) radio network object parameters
autoconfigure (AC)
Parameter name
Autoconfigure
Abbreviated name
autoConfig
Managed object
BCF
Multiplicity
1
Description
With this parameter you define whether the BCF is
created to be autoconfigured.
The parameter is only available for MetroSite, UltraSite, Flexi EDGE, BTSplus and Flexi Multiradio.
Modification from Legacy Abis to Packet Abis is not
possible for an autoconfigure BCF. Migration to
Packet Abis requires recreation of the BCF and
TRXs in Packet Abis mode.
NOTE: This parameter is valid when BCF has
Legacy Abis in use.
Additional information
-
Range
BCF is not created (N) (0), BCF is created to be
autoconfigured (Y) (1)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
BCF is not created (N) ==> 0
BCF is created to be autoconfigured (Y) ==> 1
Default value
BCF is not created (N) (0)
Default value notes
No
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
lapdLinkName of BCF - If this parameter has value
(Y) then the parameter LAPD Link Name is obligatory.
Parameter relationships
-
Related options
•
Feature dependencies
-
Table 100
DN9813866
Abis Auto Configuration (32)
Autoconfigure
Id:0900d8058089b05e
Confidential
177
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
•
MML Commands
EFC
MML Abbreviated Name
AC
MML Full Name
autoconfigure
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 100
8.4
Autoconfigure (Cont.)
automatic unlock allowed (AU)
Parameter name
Automatic Unlock Allowed
Abbreviated name
autoUnlAllowed
Managed object
BCF
Multiplicity
1
Description
With this parameter you define if automatic unlock
is used at creation of Flexi EDGE or Flexi Multiradio
BCF and also if OMUSIG with highest priority can
be chosen in autoconnection.
Note: Parameter is relevant for Flexi EDGE and
Flexi Multiradio site types only but it is visible at
NetAct for other BCF types also.
Note: Value 2 (automatic unlock allowed and
chosen highest priority OMUSIG) is not allowed if
Flexi BTS AutoConnection (143) is OFF.
Additional information
-
Range
automatic unlock not allowed (F) (0), automatic
unlock allowed (T) (1), autom unlock allowed and
chosen highest prior OMUS (2)
Step
-
Unit
-
Table 101
178
Automatic Unlock Allowed
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
gui ==> internal
automatic unlock not allowed (F) ==> 0
automatic unlock allowed (T) ==> 1
autom unlock allowed and chosen highest prior
OMUS ==> 2
Default value
automatic unlock allowed (T) (1)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
bcfType of BCF - Automatic unlock allowed parameter is only for Flexi EDGE and Flexi Multiradio BTS
site types.
Parameter relationships
-
Related options
-
Feature dependencies
•
BSS20847: Automatic commissioning of the
Flexi EDGE BTS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
AU
MML Full Name
automatic unlock allowed
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 101
8.5
abis interface connection type (AICT)
Parameter name
Abis Interface Connection Type
Abbreviated name
abisInterfaceConnectionType
3GPP name
-
Managed Object
BCF
Table 102
DN9813866
Automatic Unlock Allowed (Cont.)
Abis interface connection type
Id:0900d8058089b05e
Confidential
179
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Multiplicity
1
Description
With this parameter you define type of the Abis connection which is used in BCF.
However, when Packet Abis over TDM BCF uses
Local Switching or Packet Abis IP/TDM Aggregation, HDLC Link ID(s) are defined only for HubBCFs (Abis connection type is Packet Abis over
TDM (LS Hub)or Packet Abis over TDM (AGG
HUB) ).
Packet Abis over Ethernet – TDM is used when
BCF is locating behind the media converter (Abis
connection type is Ethernet in BSC and TDM in
BCF).Packet Abis over Ethernet – TDM (LS) is
used when BCF is locating behind the media converter (Abis connection type is Ethernet in BSC and
TDM in BCF) and BCF in question belongs to Local
Switching BCF group.
If connection type is other than Legacy abis, you
must define also ETP Object ID parameter and corresponding ETP object must exist in BSC.
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
0 (Legacy Abis), 1 (Packet Abis over TDM), 2
(Packet Abis over Ethernet), 3 (Packet Abis over
TDM (LS HUB)), 4 (Packet Abis over TDM (AGG
HUB)), 5 (Packet Abis over Ethernet - TDM), 6
(Packet Abis over Ethernet - TDM (LS))
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
Legacy Abis ==> 0
Packet Abis over TDM ==> 1
Packet Abis over Ethernet ==> 2
Default value
Legacy Abis (0)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
Parameter can only be modified when BCF is
locked. GPRS must be disabled in every BTSs
under BCF.
Table 102
180
Abis interface connection type (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Related parameters
bcfHdlcIdList of BCF - If the BCF Abis connection
type is Packet Abis over TDM (LS Hub) or Packet
Abis over TDM (AGG HUB) at least one open
HDLC link is mandatory for unlocked BCF.
btsMPlaneIpAddress of BCF - If abis interface connetion type is Packet Abis over TDM or Packet Abis
over Ethernet then btsMplaneIP address is mandatory to give in BCF creation and modification.
packetAbisBcfGroupId of BCF - If the BCF Abis
connection type is Packet Abis over TDM (LS Hub)
or Packet Abis over TDM (AGG HUB), the BCF
parameter PACKET ABIS BCF GROUP ID is mandatory. If the BCF Abis connection type is Packet
Abis over Ethernet – TDM and Packet Abis BCF
Group ID is defined as 1-3000 the BCFs in the
group supports IP/TDM aggregation.
usedEtpId of BCF - If parameter Abis Interface
Connection Type value is other than 0 (Legacy
abis), parameter Used ETP ID is obligatory
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) (optional) OR
Packet Abis over TDM (151) (optional) OR Local
Switching for Packet Abis (156) (optional), Packet
Abis IP/TDM Aggregation (163) (optional)
Feature dependencies
BSS21327 Local Switching For Packet Abis (standard), BSS21440 Packet Abis over TDM (standard), BSS21454 Packet Abis over IP/Eth
(standard), BSS21539 Packet Abis IP/TDM Aggregation (standard), BSS101414 Packet Abis Transport Media Conversion (standard)
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
AICT
MML Commands
EFC, EFM, EFO
MML Full Name
abis interface connection type
Segment Level Parameter
-
Table 102
DN9813866
Abis interface connection type (Cont.)
Id:0900d8058089b05e
Confidential
181
Base Control Function (BCF) radio network object parameters
8.6
attached CSDAP 1 (CSDAP1)
Parameter name
Attached CSDAP 1
Abbreviated name
csdapId1
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter identifies the first circuit switched
dynamic Abis pool that is attached to the BCF.
Additional information
-
Range
1...1000
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
Not used
Special value
Not used (0)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
abisInterfaceConnectionType of BCF - Attached
CSDAP 1 is valid only if ‘Abis Interface Connection
Type’ is Legacy Abis
Parameter relationships
-
Related options
Circuit Switched Dynamic Abis Pool (147)
Feature dependencies
BSS30385: Circuit Switched Dynamic Abis Pool
Interfaces
RAC <-> RACAppRAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
CSDAP1
MML Commands
EFC, EFO, EFM
MML Full Name
attached CSDAP 1
Segment Level Parameter
-
Table 103
182
BSS Radio Network Parameter Dictionary
attached CSDAP 1
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
8.7
attached CSDAP 2 (CSDAP2)
Parameter name
Attached CSDAP 2
Abbreviated name
csdapId2
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter identifies the second circuit
switched dynamic Abis pool that is attached to the
BCF.
Additional information
-
Range
1...1000
Step
1
Units
-
Formula for getting
internal value
internal_value = gui_value
Default value
0
Default value notes
Not used
Special value
Not used (0)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
abisInterfaceConnectionType of BCF - Attached
CSDAP 2 is valid only if ‘Abis Interface Connection
Type’ is Legacy Abis
Parameter relationships
-
Related options
Circuit Switched Dynamic Abis Pool (147)
Feature dependencies
BSS30385: Circuit Switched Dynamic Abis Pool
Interfaces
RAC <-> RACAppRAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
CSDAP2
MML Commands
EFC, EFO, EFM
MML Full Name
attached CSDAP 2
Table 104
DN9813866
Base Control Function (BCF) radio network object parameters
attached CSDAP 2
Id:0900d8058089b05e
Confidential
183
Base Control Function (BCF) radio network object parameters
Segment Level Parameter
Table 104
8.8
-
attached CSDAP 2 (Cont.)
attached CSDAP 3 (CSDAP3)
Parameter name
Attached CSDAP 3
Abbreviated name
csdapId3
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter identifies the third circuit switched
dynamic Abis pool that is attached to the BCF.
Additional information
-
Range
1...1000
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
Not used
Special value
Not used (0)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
abisInterfaceConnectionType of BCF - Attached
CSDAP 3 is valid only if ‘Abis Interface Connection
Type’ is Legacy Abis
Parameter relationships
-
Related options
Circuit Switched Dynamic Abis Pool (147)
Feature dependencies
BSS30385: Circuit Switched Dynamic Abis Pool
Interfaces
RAC <-> RACAppRAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
CSDAP3
Table 105
184
BSS Radio Network Parameter Dictionary
attached CSDAP 3
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
MML Commands
EFC, EFO, EFM
MML Full Name
attached CSDAP 3
Segment Level Parameter
-
Table 105
8.9
attached CSDAP 3 (Cont.)
attached CSDAP 4 (CSDAP4)
Parameter name
Attached CSDAP 4
Abbreviated name
csdapId4
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter identifies the fourth circuit switched
dynamic Abis pool that is attached to the BCF.
Additional information
-
Range
1...1000
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
Not used
Special value
Not used (0)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
abisInterfaceConnectionType of BCF - Attached
CSDAP 4 is valid only if ‘Abis Interface Connection
Type’ is Legacy Abis
Parameter relationships
-
Related options
Circuit Switched Dynamic Abis Pool (147)
Feature dependencies
BSS30385: Circuit Switched Dynamic Abis Pool
Interfaces
RAC <-> RACAppRAC <-> BSC
References
-
Table 106
DN9813866
Base Control Function (BCF) radio network object parameters
attached CSDAP 4
Id:0900d8058089b05e
Confidential
185
Base Control Function (BCF) radio network object parameters
File based provisioning
supported
true
MML Abbreviated Name
CSDAP4
MML Commands
EFC, EFO, EFM
MML Full Name
attached CSDAP 4
Segment Level Parameter
-
Table 106
8.10
BSS Radio Network Parameter Dictionary
attached CSDAP 4 (Cont.)
BCCH TRX shutdown timer (BTIM)
Parameter name
BCCH TRX Shutdown Timer
Abbreviated name
bcchTrxBatbuTimer
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the time period after
which shutdown group 0 TRXs are powered down.
The time begins after the TRX Shutdown Timer1
has expired. Parameter is valid if BTS Battery
Backup Procedure parameter has value "Transmission and BCCH Alive (1)" or "Transmission Alive
(2)". Also BCCH TRXs are powered down when
battery backup procedure parameter has value
"Transmission Alive (2)".
NOTE: Likewise this parameter is valid only if
Adjustable Intelligent Shutdown for Flexi EDGE or
Adjustable Intelligent Shutdown for MetroSite,
UltraSite and Talk-family licence (according to site
type) is ON/CONFIG OR the FIFILE/PRFILE option
for intelligent shutdown is ON, see below for
FIFILE/PRFILE options:
- MetroSite: BTS_METRO_SITE_BATBU_PR
- Talk-family: BTS_SITE_BATBU_PROC_A AND
BTS_SIT_BATBU_PROC
- UltraSite, Flexi EDGE, BTSplus, Flexi Multiradio
and Horizon: BTS_ULTRA_SITE_BATBU_PR
Additional information
-
Range
0...600
Step
1
Table 107
186
BCCH TRX Shutdown Timer
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Unit
min
Formula for getting
internal value
internal_value = gui_value * 6000
Default value
0 min
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
batteryBackupProcedure of BCF - Defines the
shutdown procedure to be used (all TRXs shut
down according to shutdown timers, only BCCH
TRX left on or all TRXs left on).
normTrxBatbuTimer of BCF - Group 1 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + normTrxBatbuTimer + batteryBackupTimer
batteryBackupTimer of BSC - Defines the time
period for trying to make forced HOs.
normTrxBatbuTimer2 of BCF - Group 2 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + batteryBackupTimer
normTrxBatbuTimer3 of BCF - Group 3 TRXs are
shut down after normTrxBatbuTimer3 + batteryBackupTimer
trxShutdownGroup of TRX - Defines to which
shutdown group the TRX belongs in a mains failure
case.
Parameter relationships
-
Related options
•
Remote Degration Of BTS Service Under TRX
Shutdown (2) (optional) OR BTS Metro Site
Batbu Pr (73) (optional) OR BTS Ultra Site
Batbu Pr (74) (optional) OR Adjustable Intelligent Shutdown, 2G Flexi (101) (optional) OR
Adjustable Intelligent Shutdown for MetroSite,
UltraSite, Talk-family (102) (optional)
Feature dependencies
•
•
BSS20151: Adjustable Intelligent Shutdown
BSS20903: Adjustable Intelligent Shutdown,
2G Flexi
Table 107
DN9813866
BCCH TRX Shutdown Timer (Cont.)
Id:0900d8058089b05e
Confidential
187
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
•
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
BTIM
MML Full Name
BCCH TRX shutdown timer
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 107
8.11
BCCH TRX Shutdown Timer (Cont.)
BCF identification (BCF)
Parameter name
BCF ID
Abbreviated name
id
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the BCF with a decimal
number.
Range Note:
The value range depends on the BSC hardware configuration and the corresponding options.
Additional information
-
Range
1..4400
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Table 108
188
BCF ID
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS21149: Flexi BSC
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EFC, EFD, EFO, EFM, EFR, EFS, EFT, EFX, EEI
MML Abbreviated Name
BCF
MML Full Name
BCF identification
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 108
8.12
BCF ID (Cont.)
BTS C/U-plane IP address (BCUIP)
Parameter name
BTS CU-plane IP Address
Abbreviated name
btsCuPlaneIpAddress
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
Parameter is used as IPv4 source address for UL
C/U-plane packets and as IPv4 destination address
for DL C/U-plane packets.
Conventional representation of the numeric IP
address in dotted decimal notation #.#.#.# with #
ranging from 0 to 255.
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
7...15
Step
-
Units
characters
Formula for getting
internal value
internal_value = gui_value
Table 109
DN9813866
BTS CU-plane IP Address
Id:0900d8058089b05e
Confidential
189
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value
0.0.0.0
Default value notes
Not used
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
If Packet abis is used or BCF is modified to use
Packet abis then this parameter can be modified
only when BCF is locked.
Related parameters
btsIpv4SubnetMasklengthCUplane of BCF - If User
has given the BTS CU-plane IP Address then also
BTS IPv4 Subnet Mask Length for C/U-plane
parameter must be given.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RACBSC <-> RAC
References
-
File based provisioning
supported
true
MML Abbreviated Name
BCUIP
MML Commands
EFO, EFM, EFC
MML Full Name
BTS C/U-plane IP address
Segment Level Parameter
-
Table 109
8.13
BTS IPv4 subnet mask length for C/U-plane (SMCUP)
Parameter name
BTS IPv4 Subnet Mask Length for C/U-plane
Abbreviated name
btsIpv4SubnetMasklengthCUplane
3GPP name
-
Managed Object
BCF
Multiplicity
1
Table 110
190
BTS CU-plane IP Address (Cont.)
BTS IPv4 Subnet Mask Length for C/U-plane
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Description
With this parameter you define subnet mask length
for BTs Ipv4 address (C/U-plane).
If Packet Abis is used, mask must be always given.
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
1...32
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
-
Default value notes
-
Special value
subnet mask is not given. (0)
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
If Packet abis is used or BCF is modified to use
Packet abis then this parameter can be modified
only when BCF is locked.
Related parameters
btsCuPlaneIpAddress of BCF - If User has given
the BTS C/U-plane IP Address then also BTS IPv4
Subnet Mask Length for C/U-plane must be given.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) (optional) OR Packet
Abis over TDM (151) (optional)
Feature dependencies
-
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: BSS21454 - Packet Abis over
IP/EthNSN reference: BSS21440 - Packet Abis
over TDM Standard
File based provisioning
supported
true
MML Abbreviated Name
SMCUP
MML Commands
EFC, EFM, EFO
MML Full Name
BTS IPv4 subnet mask length for C/U-plane
Segment Level Parameter
-
Table 110
DN9813866
BTS IPv4 Subnet Mask Length for C/U-plane (Cont.)
Id:0900d8058089b05e
Confidential
191
Base Control Function (BCF) radio network object parameters
8.14
BSS Radio Network Parameter Dictionary
BTS IPv4 subnet mask length for M-plane (SMMP)
Parameter name
BTS IPv4 Subnet Mask Length for M-plane
Abbreviated name
btsIpv4SubnetMasklengthMplane
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define subnet mask length
for BTs Ipv4 address (M-plane).
If Packet Abis is used, mask must be always given.
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
1...32
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
-
Default value notes
Subnet mask is not given.
Special value
Subnet mask is not given. (0)
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
If Packet abis is used or BCF is modified to use
Packet abis then this parameter can be modified
only when BCF is locked.
Related parameters
btsMPlaneIpAddress of BCF - If User has given the
BTS M-plane IP Address then also BTS IPv4
Subnet Mask Length for M-plane must be given.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) (optional) OR Packet
Abis over TDM (151) (optional)
Feature dependencies
-
Interfaces
BSC <-> RAC
RAC <-> RACApp
Table 111
192
BTS IPv4 Subnet Mask Length for M-plane
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
References
NSN reference: BSS21454 - Packet Abis over
IP/EthNSN reference: BSS21440 - Packet Abis
over TDM Standard
File based provisioning
supported
true
MML Abbreviated Name
SMMP
MML Commands
EFC, EFM, EFO
MML Full Name
BTS IPv4 subnet mask length for M-plane
Segment Level Parameter
-
Table 111
8.15
Base Control Function (BCF) radio network object parameters
BTS IPv4 Subnet Mask Length for M-plane (Cont.)
BTS M-plane IP address (BMIP)
Parameter name
BTS M-plane IP address
Abbreviated name
btsMPlaneIpAddress
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
Parameter is used as IPv4 source address for UL
M-plane packets and as IPv4 destination address
for DL M-plane packets.
Conventional representation of the numeric IP
address in dotted decimal notation #.#.#.# with #
ranging from 0 to 255.
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
7...15
Step
-
Units
characters
Formula for getting
internal value
internal_value =gui_value
Default value
0.0.0.0
Default value notes
Not used
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Table 112
DN9813866
BTS M-plane IP address
Id:0900d8058089b05e
Confidential
193
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Modified
If Packet abis is used or BCF is modified to use
Packet abis then this parameter can be modified
only when BCF is locked.
Related parameters
abisInterfaceConnectionType of BCF - If Abis Interface Connection is other Legacy, then BTS M-plane
IP Address parameter is mandatory.
btsIpv4SubnetMasklengthMplane of BCF - If User
has given the BTS M-plane IP address then also
BTS IPv4 Subnet Mask Length for M-plane must be
given.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
BSC <-> RAC
RACApp <-> RAC
References
-
File based provisioning
supported
true
MML Abbreviated Name
BMIP
MML Commands
EFO, EFM, EFC
MML Full Name
BTS M-plane IP address
Segment Level Parameter
-
Table 112
8.16
BTS M-plane IP address (Cont.)
bit rate (BR)
Parameter name
Bit Rate
Abbreviated name
bitRate
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the bit rate of the Dchannel O&M signalling link of the BCF.
NOTE: The parameter is only available for MetroSite, UltraSite, Flexi EDGE, BTSplus, Flexi Multiradio and Horizon.
NOTE: No NetAct Interface.
Table 113
194
Bit Rate
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Additional information
-
Range
8 kbps (8), 16 kbps (16), 32 kbps (32), 64 kbps (64)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
8 kbps ==> 8
16 kbps ==> 16
32 kbps ==> 32
64 kbps ==> 64
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
autoConfig of BCF - If this parameter is given then
the Auto Configuration parameter value must be
Yes (Y). , lapdLinkNumber of BCF - This parameter
is mandatory when the LAPD Link Number is not
given.
Parameter relationships
-
Related options
-
Related features
-
Interfaces
-
References
-
MML Commands
EFC
MML Abbreviated Name
BR
MML Full Name
bit rate
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 113
8.17
Bit Rate (Cont.)
BSC-BSC interface failure (BSCBSC)
Parameter name
Table 114
DN9813866
BSC-BSC interface failure
BSC-BSC interface failure
Id:0900d8058089b05e
Confidential
195
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Abbreviated name
bscBscInterfaceFailure
Managed object
BCF
Multiplicity
1
Description
With this parameter you output the synchronisation data
and DFCA TRXs of the DFCA BTSs which have the
defined BSC-BSC interface status. The data of a BTS is
output, if the DFCA mode of the BTS is STANDBY or
DFCA hopping and the BTS has the BSC-BSC interface
status defined by this parameter.
NOTE: MML RANGE:
OK = Output DFCA BTSs which do not suffer from a
BSC-BSCinterface failure.
NOK = Output DFCA BTSs which suffer from a BSCBSCinterface failure.
Additional information
-
Range
NOK (0), OK (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
NOK ==> 0
OK ==> 1
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
-
References
-
MML Commands
EFL
MML Abbreviated Name
BSCBSC
MML Full Name
BSC-BSC interface failure
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 114
196
BSC-BSC interface failure (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
8.18
Base Control Function (BCF) radio network object parameters
BTS battery backup procedure (BBU)
Parameter name
BTS Battery Backup Procedure
Abbreviated name
batteryBackupProcedure
Managed object
BCF
Multiplicity
1
Description
With this parameter you define what type of BTS
battery backup procedure is used. The procedure is
executed when the mains power goes down at the
BTS site and there is a battery backup unit.
NOTE:
MML RANGE:
ALL (transmission equipment and all TRXs are left
alive)
BCCH (transmission equipment and only the BCCH
TRX are left alive)
NONE (only transmission equipment is left alive)
MML DEFAULT: ALL
NOTE: This parameter is valid only when Adjustable Intelligent Shutdown for FlexiEDGE or Adjustable Intelligent Shutdown for MetroSite, UltraSite
and Talk-family licence (according to site type) is
ON/CONFIG OR the FIFILE/PRFILE option for
intelligent shutdown is ON, see below for
FIFILE/PRFILE options:
MetroSite: BTS_METRO_SITE_BATBU_PR
Talk-family: BTS_SITE_BATBU_PROC_A AND
BTS_SIT_BATBU_PROC
UltraSite, Flexi EDGE, BTSplus, Flexi Multiradio
and Horizon: BTS_ULTRA_SITE_BATBU_PR
Additional information
-
Range
All Alive (0), Transmission and BCCH Alive (1),
Transmission Alive (2)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
All Alive ==> 0
Transmission and BCCH Alive ==> 1
Transmission Alive ==> 2
Default value
Table 115
DN9813866
All Alive (0)
BTS Battery Backup Procedure
Id:0900d8058089b05e
Confidential
197
Base Control Function (BCF) radio network object parameters
Default value notes
ALL
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
bcchTrxBatbuTimer of BCF - Group 0 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + normTrxBatbuTimer +
bcchTrxBatbuTimer + batteryBackupTimer ,
normTrxBatbuTimer of BCF - Group 1 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + normTrxBatbuTimer + batteryBackupTimer , batteryBackupTimer of BSC Defines the time period for trying to make forced
HOs. , normTrxBatbuTimer2 of BCF - Group 2
TRXs are shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + batteryBackupTimer ,
normTrxBatbuTimer3 of BCF - Group 3 TRXs are
shut down after normTrxBatbuTimer3 + batteryBackupTimer , trxShutdownGroup of TRX - Defines
to which shutdown group the TRX belongs in a
mains failure case.
Parameter relationships
-
Related options
•
Remote Degration Of BTS Service Under TRX
Shutdown (2) (optional) OR BTS Metro Site
Batbu Pr (73) (optional) OR BTS Ultra Site
Batbu Pr (74) (optional) OR Adjustable Intelligent Shutdown for Flexi EDGE (101) (optional)
OR Adjustable Intelligent Shutdown for MetroSite, UltraSite, Talk-family (102) (optional)
Related features
•
•
BSS20151: Adjustable Intelligent Shutdown
BSS20903: Separate Licence for Flexi EDGE
BTS Intelligent Shutdown
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
BBU
MML Full Name
BTS battery backup procedure
Table 115
198
BSS Radio Network Parameter Dictionary
BTS Battery Backup Procedure (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 115
8.19
Base Control Function (BCF) radio network object parameters
BTS Battery Backup Procedure (Cont.)
BTS site subtype (-)
Parameter name
BTS Site Subtype
Abbreviated name
btsSiteSubtype
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the subtype of the
BTS site. Parameter is not modifiable.
NOTE: Parameter is mandatory if site type is
BTSplus.
NOTE: Parameter is valid only for BTSplus, Flexi
Multiradio 10 or Flexi Compact. Parameter values 0
– 2 are valid only for BTSplus site type. Parameter
values 3, 4 and FF are valid only for Flexi Multiradio
site type.
Additional information
-
Range
(Mainline (M)) (0), (eMicro (E)) (1), (Basic (B)) (2),
(Flexi Multiradio 10 BTS (R)) (3), (Flexi Compact
BTS (C)) (4),( No BTS sub site or Flexi Multiradio
BTS (F)) (255)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Mainline (M) ==> 0
eMicro (E) ==> 1
Basic (B) ==> 2
No BTS sub site ==> 255
Default value
No BTS sub site (255)
Default value notes
Value 255 is used with other site types.
Required on Creation
Parameter is mandatory if site type is BTSplus,
Flexi Multiradio 10 or Flexi Compact.
Related functions
-
Modification
objectLocking
Table 116
DN9813866
BTS Site Subtype
Id:0900d8058089b05e
Confidential
199
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Modified
Parameter is modifiable for Flexi Multiradio BTS,
but not modifiable for BTSplus.
Related parameters
BCF-bcfType Parameter values 0 (Mainline), 1
(eMicro) and 2 (Basic) are available only for
BTSplus type of BTS site. Parameter values 3
(Flexi Multiradio 10 BTS), 4 (Flexi Compact BTS)
and 255 (Flexi Multiradio) are available only for
Flexi Multiradio type of BTS site. Value 255 is used
with other site types.
Parameter relationships
-
Related options
-
Related features
•
•
•
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
•
BSS101688 BSC SUPPORT FOR FLEXI MULTIRADIO 10 BTS
RG301613 BSC SUPPORT FOR FLEXI
COMPACT BTS
•
MML Commands
EFC, EFM, EFO, EEI
MML Abbreviated Name
-
MML Full Name
BTS site subtype
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 116
8.20
BTS Site Subtype (Cont.)
BCF HDLC ID list (BHIDL)
Parameter name
BCF HDLC ID list
Abbreviated name
bcfHdlcIdList
3GPP name
-
Managed Object
BCF
Multiplicity
8
Table 117
200
BSS21469: BS2xx@Flexi BSC product family
BSS101688 BSC SUPPORT FOR FLEXI
MULTIRADIO 10 BTS
RG301613 BSC SUPPORT FOR FLEXI
COMPACT BTS
BCF HDLC ID list
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Description
With this parameter you define the Abis HDLC link
IDs that are defined for BCF.
HDLC links can not be added to Terminal BCF.
NOTE: BCF has to be locked if there are no open
Abis HDLC link configured in BCF.
MML NOTE:
By giving value 0 (zero) means empty HDLC list is
given i.e. all existing HDLC(s) attached to BCF are
removed.
Additional information
-
Range
1...3000
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
-
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
hdlcLinkId of HDLC - Corresponding HDLC link has
to exist before giving it to BCF
Parameter relationships
-
Related options
Packet Abis over TDM (151)
Feature dependencies
BSS21440 Packet Abis over TDM
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
BHIDL
MML Commands
EFC, EFM, EFO
MML Full Name
BCF HDLC ID list
Segment Level Parameter
-
Table 117
DN9813866
BCF HDLC ID list (Cont.)
Id:0900d8058089b05e
Confidential
201
Base Control Function (BCF) radio network object parameters
8.21
BSS Radio Network Parameter Dictionary
BCF up to date (BCFUTD)
Parameter name
BCF Up to Date
Abbreviated name
bcfUpToDate
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter indicates whether the BCF Packet
Abis parameters are up to date in BTS and ETPE/T
or A over IP parameters in ETPA
MML NOTE: The parameter is only shown in
outputs.
Additional information
NOTE:
Range in binary:
000 -> BCF is up to date in BTS and ETP(E/T)
001 -> BCF Packet Abis parameter(s) are not up to
date in BTS
010 -> BCF Packet Abis parameter(s) are not up to
date in ETP(E/T)
011 -> BCF Packet Abis parameter(s) are not up to
date in BTS nor ETP(E/T)
100 -> BCF Packet Abis parameter(s) are not up to
date in ETP(A)
101 -> BCF Packet Abis parameter(s) are not up to
date in BTS nor ETP(A)
111 -> BCF Packet Abis parameter(s) are not up to
date in BTS nor ETP(E/T) nor ETP(A) MML NOTE:
If value is zero, MML printout is BCF UP TO DATE
.............................................
T If value is over zero, e.g. 3 (in binary 011) value
is F and rows after that are printed depending on
the value BCF UP TO
DATE.............................................
F BCF PARAMETERS NOT UPDATED TO BTS
BCF PARAMETERS NOT UPDATED TO ETP(E/T)
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Range
0...7
Step
1
Units
-
Table 118
202
BCF Up to Date
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
BCF is up to date
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151) or
AoIP Transcoder in BSS (157) or
AoIP Transcoder in MGW (158)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
BCFUTD
MML Commands
EFO
MML Full Name
BCF up to date
Segment Level Parameter
-
Table 118
8.22
BTS C/U-plane IP address
Parameter name
BTS C/U-plane IP address
Abbreviated name
btsCuPlaneIpAddress
Managed object
BCF
Multiplicity
1
Table 119
DN9813866
BCF Up to Date (Cont.)
BTS C/U-plane IP address
Id:0900d8058089b05e
Confidential
203
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
BTS C/U-plane IP address is stored by system from
platform parameter of SCTP association of
TRXSIG.
MML NOTE:
The parameter is only shown in outputs.
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
0...0
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
Value set by the system
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Packet Abis over IP/Eth (150) (optional) OR
Packet Abis over TDM (151) (optional)
Feature dependencies
•
•
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
•
BSC -> RAC
References
-
MML Commands
EFO
MML Abbreviated Name
-
MML Full Name
BTS C/U-plane IP address
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 119
204
BTS C/U-plane IP address (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
8.23
Base Control Function (BCF) radio network object parameters
BTS commissioning state (CSTAT)
Parameter name
BTS Commissioning State
Abbreviated name
btsCommissioningState
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter indicates the current commissioning state of the BTS. The parameter value changes
report the proceeding of the BTS commissioning.
Only system can modify this parameter.
MML NOTE: The parameter is only shown in
outputs.
This parameter is valid only for Flexi EDGE BTSs
and Flexi Multiradio BTSs.
Additional information
-
Range
not defined (0), SCF ready for downloading (1),
SCF download ongoing (2), commission initiated
(3), commission ended (4), conflicting OMUSIGs
(5), no SCF available for download (6)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
not defined ==> 0
SCF ready for downloading ==> 1
SCF download ongoing ==> 2
commission initiated ==> 3
commission ended ==> 4
conflicting OMUSIGs ==> 5
no SCF available for download ==> 6
Default value
not defined (0)
Default value notes
not defined
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Table 120
DN9813866
BTS Commissioning State
Id:0900d8058089b05e
Confidential
205
Base Control Function (BCF) radio network object parameters
Related options
Flexi BTS Autoconnection (143)
Feature dependencies
BSS21316: Flexi BTS Autoconnection
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
CSTAT
MML Commands
EEB
MML Full Name
BTS commissioning state
Segment Level Parameter
-
Table 120
8.24
BSS Radio Network Parameter Dictionary
BTS Commissioning State (Cont.)
BTS M-plane IP address
Parameter name
BTS M-plane IP address
Abbreviated name
btsMPlaneIpAddress
Managed object
BCF
Multiplicity
1
Description
BTS M-plane IP address is stored by system from
platform parameter of SCTP association of
OMUSIG.
MML NOTE:
The parameter is only shown in outputs.
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
0...0
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
Value set by the system
Related functions
-
Modification
Not modifiable
Table 121
206
BTS M-plane IP address
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Packet Abis over IP/Eth (150) (optional) OR
Packet Abis over TDM (151) (optional)
Feature dependencies
•
•
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
•
BSC -> RAC
References
-
MML Commands
EFO
MML Abbreviated Name
-
MML Full Name
BTS M-plane IP address
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 121
8.25
Base Control Function (BCF) radio network object parameters
BTS M-plane IP address (Cont.)
BTS serial number ()
Parameter name
BTS Serial Number
Abbreviated name
btsSerialNumber
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameters indicates the BTS serial number.
In conflicting OMUSIGs case, BSC uses this
parameter to resolve the source of the BTS registration messages.
Only system can modify this parameter.
MML NOTE: The parameter is only shown in
outputs.
Additional information
In BCF creation this parameter is initialized with
ASCII nils (30H).
Range
12
Step
-
Units
characters
Table 122
DN9813866
BTS Serial Number
Id:0900d8058089b05e
Confidential
207
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
internal_value =gui_value
Default value
-
Default value notes
-
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Flexi BTS Autoconnection (143)
Feature dependencies
BSS21316: Flexi BTS Autoconnection
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
-
MML Commands
EEB
MML Full Name
BTS serial number
Segment Level Parameter
-
Table 122
8.26
BTS Serial Number (Cont.)
BU1 abis throughput threshold (BU1)
Parameter name
BU1 Abis Throughput Threshold
Abbreviated name
bu1AbisThroughputThreshold
3GPP name
-
Managed Object
BCF
Multiplicity
1
Table 123
208
BSS Radio Network Parameter Dictionary
BU1 Abis Throughput Threshold
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Description
With this parameter you define a threshold to
trigger BU1 congestion reaction procedure. This
threshold defines the value of the Abis throughput
measured by BTS which triggers the BU1 congestion reaction procedures.
The algorithm handling Abis uplink throughput
measurements provides trigger for start/stop the
congestion reaction procedures when the related
thresholds are crossed up/down respectively.
NOTE:
Range in case of Packet Abis over Ethernet: 20150
Range in case of Packet Abis over TDM: 20-100
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
20...150
Step
1
Units
%
Formula for getting
internal value
internal_value =gui_value
Default value
75
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
bu2AbisThroughputThreshold of BCF - Value of the
BU2 Abis Throughput Threshold (BU2) parameter
must be bigger than value of BU1 Abis Throughput
Threshold (BU1) parameter.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
Table 123
DN9813866
BU1 Abis Throughput Threshold (Cont.)
Id:0900d8058089b05e
Confidential
209
Base Control Function (BCF) radio network object parameters
File based provisioning
supported
true
MML Abbreviated Name
BU1
MML Commands
EFM, EFO
MML Full Name
BU1 abis throughput threshold
Segment Level Parameter
-
Table 123
8.27
BSS Radio Network Parameter Dictionary
BU1 Abis Throughput Threshold (Cont.)
BU2 abis throughput threshold (BU2)
Parameter name
BU2 Abis Throughput Threshold
Abbreviated name
bu2AbisThroughputThreshold
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define a threshold to
trigger BU2 congestion reaction procedure.This
threshold defines the value of the Abis throughput
measured by BTS which triggers the BU2 congestion reaction procedures.
The algorithm handling Abis uplink throughput
measurements provides trigger for start/stop the
congestion reaction procedures when the related
thresholds are crossed up/down respectively.
NOTE:
Range in case of Packet Abis over Ethernet: 20150
Range in case of Packet Abis over TDM: 20-100
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
20...150
Step
1
Units
%
Formula for getting
internal value
internal_value =gui_value
Default value
90
Default value notes
-
Table 124
210
BU2 Abis Throughput Threshold
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
bu1AbisThroughputThreshold of BCF - Value of
this parameter BU2 Abis Throughput Threshold
(BU2) must be higher than parameter BU1 Abis
Throughput Threshold (BU1)
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
BU2
MML Commands
EFM, EFO
MML Full Name
BU2 abis throughput threshold
Segment Level Parameter
-
Table 124
8.28
clock source (CS)
Parameter name
Clock Source
Abbreviated name
clockSource
Managed object
BCF
Multiplicity
1
Table 125
DN9813866
BU2 Abis Throughput Threshold (Cont.)
Clock Source
Id:0900d8058089b05e
Confidential
211
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the clock source for
the master clock BCF or the independent mode
BCF. If the defined clock source is LMU, LMUABIS, BCF, BCF WCDMA LMU or TOP, the BCF is
a master clock BCF.
When synch of the BCF is disabled (SENA=N),
modification of the parameter can be done online.
When the synch of the BCF is enabled (SENA=Y)
and value of the Synch Status is not 'ABIS SYNCH',
then the value of the parameter can be changed
from LMU to LMU-ABIS or vice versa online.
NOTE: The parameter is only available for Talkfamily, MetroSite, UltraSite, Flexi EDGE and Flexi
Multiradio.
NOTE: MML range:
BCF (master clock BCF)
LMU (location measurement unit)
PCM (independent mode)
NONE (remove clock source)
LAB (LMU-ABIS)
BWLMU (BCF WCDMA LMU)
IWLMU (Independent WCDMA-LMU)
TOP (Timing over Package)
NOTE: MML default: NOT USED
LMU-ABIS (4) value is only available for UltraSite
and Flexi EDGE and Flexi Multiradio. BWLMU (5)
and IWLMU (6) are only available for Flexi Multiradio. Value TOP (7) is available only for Flexi Multiradio 10 when licence Packet abis sync ToP (127)
state ON/CONF.
Additional information
-
Range
(NONE (remove clock source)) (0), (LMU (location
measurement unit)) (1), (BCF (master clock BCF))
(2), ( PCM (independent mode)) (3), (LMU-ABIS)
(4), (BWLMU) (5), (IWLMU) (6), (TOP)(7)
Step
-
Unit
-
Table 125
212
Clock Source (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
gui ==> internal
NONE (remove clock source) ==> 0
LMU (location measurement unit) ==> 1
BCF (master clock BCF) ==> 2
PCM (independent mode) ==> 3
LMU-ABIS ==> 4
BWLMU ==> 5
IWLMU ==> 6
Default value
NONE (remove clock source) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
When modifying a master clock BCF, the modification can be made online if synchronisation of the
chain is disabled. When creating or removing an
independent mode BCF, the modification requires
BCF locking.
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
•
BSS21403: Flexi Multiradio TRX HW Activation
BSS21439 - Packet Abis sync. ToP
IEEE1588v2
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
MML Commands
EFC, EFM, EFO, EFL
MML Abbreviated Name
CS
MML Full Name
clock source
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 125
DN9813866
Clock Source (Cont.)
Id:0900d8058089b05e
Confidential
213
Base Control Function (BCF) radio network object parameters
8.29
BSS Radio Network Parameter Dictionary
D-channel link set name (DNAME)
Parameter name
LAPD Link Name
Abbreviated name
lapdLinkName
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the D-channel link set
name of the BTS site O&M link. NOTE: The parameter
cannot be defined for PrimeSite. Modifying the parameter
causes a temporary break in O&M signalling. NOTE:
Range: String of up to 5 characters ('A'..'Z','0'..'9'). The
first character must be a letter.
Additional information
-
Range
1...5
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
autoConfig of BCF - If this parameter is given then the
Auto Configuration parameter value must be Yes (Y), lapdLinkNumber of BCF - This parameter is mandatory
when the LAPD Link Number is not given.
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EFC, EFO, EFM, EEI
MML Abbreviated Name
DNAME
MML Full Name
D-channel link set name
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 126
214
LAPD Link Name
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
8.30
Base Control Function (BCF) radio network object parameters
D-channel link set number (DNBR)
Parameter name
LAPD Link Number
Abbreviated name
lapdLinkNumber
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the D-channel link set
number of the BTS site O&M link. NOTE: The parameter
cannot be defined for PrimeSite. Modifying the parameter
causes a temporary break in O&M signalling. MML
NOTE: Modification: Online
Additional information
-
Range
1...65535
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
autoConfig of BCF - If the Auto Configuration parameter
value is set to (Y) then this parameter can not be given,
lapdLinkName of BCF - If this parameter is given then the
parameter LAPD Link Name can not be given.
Parameter relationships
-
Related options
-
Related features
-
•
Interfaces
BSC -> RAC
References
-
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
DNBR
MML Full Name
D-channel link set number
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 127
DN9813866
LAPD Link Number
Id:0900d8058089b05e
Confidential
215
Base Control Function (BCF) radio network object parameters
8.31
BSS Radio Network Parameter Dictionary
DL committed information rate (DLCIR)
Parameter name
DL Committed Information Rate
Abbreviated name
dlCommittedInformationRate
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define the Committed
Information Rate in Downlink direction.
Value 0 (Not defined) and it is used in BCF creation
as default value to parameter database in BSC.
User cannot give this value.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
Parameter is required at BTS side for Congestion
Control
Range
100...250000
Step
100
Units
kbit/s
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Special value
Not defined (0)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
Table 128
216
Downlink Committed Information Rate
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
File based provisioning
supported
true
MML Abbreviated Name
DLCIR
MML Commands
EFM, EFO
MML Full Name
DL committed information rate
Segment Level Parameter
-
Table 128
8.32
Base Control Function (BCF) radio network object parameters
Downlink Committed Information Rate (Cont.)
Downloaded SCF File Plan Id ()
Parameter name
Downloaded SCF File Plan Id
Abbreviated name
downloadedSCFFilePlanId
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter indicates the latest site configuration plan ID downloaded from NetAct to BSC.
Only system can modify this parameter.
MML NOTE: The parameter is only shown in
outputs.
This parameter is valid only for Flexi EDGE BTSs
and Flexi Multiradio BTSs.
Additional information
-
Range
1...2147483647
Step
1
Units
-
Formula for getting
internal value
internal_value =
Default value
0
Default value notes
Not defined
Special value
Not defined (0)
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Table 129
DN9813866
gui_value
Downloaded SCF File Plan Id
Id:0900d8058089b05e
Confidential
217
Base Control Function (BCF) radio network object parameters
Parameter relationships
-
Related options
Flexi BTS Autoconnection (143)
Feature dependencies
BSS21316: Flexi BTS Autoconnection
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
-
MML Commands
EEB
MML Full Name
Downloaded SCF File Plan Id
Segment Level Parameter
-
Table 129
8.33
BSS Radio Network Parameter Dictionary
Downloaded SCF File Plan Id (Cont.)
external input number (INBR)
Parameter name
External Input Number
Abbreviated name
inputId
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the external input
number of the BCF.
NOTE: The parameter is only available for MetroSite, UltraSite, Flexi EDGE and Flexi Multiradio.
NOTE: MML RANGE: 1 ... 10 (MetroSite), 1 ... 24
(UltraSite, Flexi EDGE and Flexi Multiradio)
Additional information
-
Range
1...24
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Table 130
218
External Input Number
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
References
-
MML Commands
EFX, EFO
MML Abbreviated Name
INBR
MML Full Name
external input number
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 130
8.34
RAC <-> RACApp
RAC <-> BSC
External Input Number (Cont.)
external outputs ON / external outputs OFF (ON/OFF)
Parameter name
External Outputs
Abbreviated name
bcfOutputInUse
Managed object
BCF
Multiplicity
6
Table 131
DN9813866
Base Control Function (BCF) radio network object parameters
External Outputs
Id:0900d8058089b05e
Confidential
219
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the external outputs
that are set to ON or OFF stateWith this parameter
you define the external outputs that are set to ON,
OFF or Not used state. ‘Not used’ state is only for
Flexi Multiradio 10 BTS which have physical 12
EAC lines including exclusive 6 EAC inputs (numbering 1-6), and selective additional 6 EAC inputs
(numbering 7-12) or 6 EAC outputs (numbering 16). With value ‘not used’ EAC line can be used for
additional input lines.
The outputs are identified by a number.
NOTE: The parameter cannot be defined for PrimeSite. In the case of MetroSite, the number of
external outputs is 4. In the case of 2nd Generation,
Talk-family, UltraSite, Flexi EDGE, BTSplus and
Flexi Multiradio, the number of external outputs is 6.
MML NOTE:
range: 6 outputs of type ON/OFF/not used.
Default value: all outputs OFF
Additional information
-
Range
false (0), true (1), not used (FF)
Step
-
Unit
-
Formula for getting
internal value
•
•
Default value
false (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
•
•
References
-
Table 131
220
false => 0
true => 1
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
External Outputs (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
MML Commands
EFO, EFT
MML Abbreviated Name
ON/OFF
MML Full Name
external outputs ON / external outputs OFF
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 131
8.35
Base Control Function (BCF) radio network object parameters
External Outputs (Cont.)
external synchronization source (ESS)
Parameter name
External Synchronization Source
Abbreviated name
syncSource
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the synchronisation
source of the master clock TRX for a synchronised
PrimeSite BTS site. If the site is not synchronised
but stand-alone, the parameter defines a synchronisation source for all the TRXs in the site. NOTE:
See also the Master Clock TRX parameter.
Additional information
-
Range
BTS Internal (0), PCM External (2), Other External
(3)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
BTS Internal ==> 0
PCM External ==> 2
Other External ==> 3
Default value
PCM External (2)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Table 132
DN9813866
External Synchronization Source
Id:0900d8058089b05e
Confidential
221
Base Control Function (BCF) radio network object parameters
Related parameters
masterClock of BCF - By using parameter Master
Clock TRX, you can synchronise the site so that the
parameter External Synchronization Source does
not define the synchronisation source for all the
TRXs in the site.
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
•
•
References
-
MML Commands
EFO, EFM
MML Abbreviated Name
ESS
MML Full Name
external synchronization source
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 132
8.36
BSS Radio Network Parameter Dictionary
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
External Synchronization Source (Cont.)
ethernet ring/path protection (ERPP)
Parameter name
Ethernet Ring/Path Protection
Abbreviated name
ethernetRingPathProtection
Managed object
BCF
Multiplicity
1
Description
With this parameter you can enable Ethernet
Ring/Path Protection feature in BTS.
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
disabled (0), enabled (1)
Step
-
Unit
-
Table 133
222
Ethernet Ring/Path Protection
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
gui ==> internal
disabled ==> 0
enabled ==>1
Default value
disabled (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Ethernet Ring/Path Protection (166)
Feature dependencies
•
BSS101406 Ethernet ring/path protection
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: BSS101406 - Ethernet ring/path
protection
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
ERPP
MML Full Name
ethernet ring/path protection
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 133
8.37
ETP BCF ID (EBID)
Parameter name
ETP BCF ID
Abbreviated name
etpBcfId
3GPP name
-
Managed Object
BCF
Multiplicity
1
Table 134
DN9813866
Ethernet Ring/Path Protection (Cont.)
ETP BCF ID
Id:0900d8058089b05e
Confidential
223
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
This parameter identifies the internal BCF ID for
ETP and ETME use. System generates the parameter when BCF is created/modified for Packet Abis
use. Parameter is output parameter only. Parameter is unique for each BCF inside ETP.
MML NOTE:
The parameter is only shown in outputs.
Additional information
-
Range
0..1099
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
-
Default value notes
-
Special value
ETP related ID is not defined to BCF (65535)
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
EBID
MML Commands
EFO
MML Full Name
ETP BCF ID
Segment Level Parameter
-
Table 134
224
ETP BCF ID (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
8.38
Base Control Function (BCF) radio network object parameters
FACCH LAPDm T200 (T200F)
Parameter name
FACCH LAPDm T200
Abbreviated name
T200F
Managed object
BCF
Multiplicity
1
Description
The parameter determines a LAPDm T200 for
supervision of the FACCH message transfer from
BTS to mobile.
NOTE: MMI is the only user interface supporting
this parameter.
NOTE: The parameter is modifiable only for Talkfamily, UltraSite, Flexi EDGE, BTSplus, Flexi Multiradio and Horizon BTSs.
NOTE: MML modification: Online
Additional information
-
Range
200...1260
Step
20
Unit
ms
Formula for getting
internal value
internal_value = gui_value / 20
Default value
0 ms
Default value notes
0 ms (BCF PREDEFINED VALUES)
Required on Creation
optional
Special value
BCF PREDEFINED VALUES (0)
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
Interfaces
-
References
-
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
T200F
MML Full Name
FACCH LAPDm T200
Table 135
DN9813866
BSS20924: BSC Support for LAPDm T200
Setting
FACCH LAPDm T200
Id:0900d8058089b05e
Confidential
225
Base Control Function (BCF) radio network object parameters
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 135
8.39
BSS Radio Network Parameter Dictionary
FACCH LAPDm T200 (Cont.)
Flexi EDGE Abis over IP Ethernet feature usage (TRS1)
Parameter name
Flexi EDGE Abis Over IP/Ethernet Feature Usage
Abbreviated name
flexiEdgeAbisOverIpEthernetUsage
Managed object
BCF
Multiplicity
1
Description
With this parameter you can enable the Flexi EDGE
Abis over IP/ Ethernet feature in the BCF.
NOTE: Range description:
0 (not in use)
1 (in use)
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
0...1
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
0
Default value notes
not in use
Required on Creation
optional
Special value
not defined, not configured after S13 upgrade (255)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
FlexiEDGE Abis over IP/ Ethernet (115)
Related features
•
BSS30305: FlexiEDGE Abis over IP/ Ethernet
Table 136
226
Flexi EDGE Abis Over IP/Ethernet Feature Usage
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Interfaces
•
•
References
-
MML Commands
EFM, EFC, EFO
MML Abbreviated Name
TRS1
MML Full Name
Flexi EDGE Abis over IP Ethernet feature usage
Segment Level Parameter
false
File Based Provisioning
supported
true
Table 136
8.40
Base Control Function (BCF) radio network object parameters
RACApp <-> RAC
RAC <-> BSC
Flexi EDGE Abis Over IP/Ethernet Feature Usage (Cont.)
Flexi EDGE TRS Abis Grooming feature usage (TRS3)
Parameter name
Flexi EDGE TRS Abis Grooming Feature Usage
Abbreviated name
flexiEdgeTrsAbisGroomingUsage
Managed object
BCF
Multiplicity
1
Description
With this parameter you can enable the Flexi EDGE
TRS Abis Grooming feature in the BCF.
NOTE: Range description:
0 (not in use)
1 (in use)
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
0...1
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
0
Default value notes
not in use
Required on Creation
optional
Special value
not defined, not configured after S13 upgrade (255)
Related functions
-
Modification
On-Line
Table 137
DN9813866
Flexi EDGE TRS Abis Grooming Feature Usage
Id:0900d8058089b05e
Confidential
227
Base Control Function (BCF) radio network object parameters
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
FlexiEDGE TRS Abis Grooming (117)
Related features
•
BSS21129: FlexiEDGE TRS Abis Grooming
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EFM, EFC, EFO
MML Abbreviated Name
TRS3
MML Full Name
Flexi EDGE TRS Abis Grooming feature usage
Segment Level Parameter
false
File Based Provisioning
supported
true
Table 137
8.41
BSS Radio Network Parameter Dictionary
Flexi EDGE TRS Abis Grooming Feature Usage (Cont.)
Flexi EDGE TRS Loop Protection feature usage (TRS4)
Parameter name
Flexi EDGE TRS Loop Protection Feature Usage
Abbreviated name
flexiEdgeTrsLoopProtectionUsage
Managed object
BCF
Multiplicity
1
Description
With this parameter you can enable the Flexi EDGE
TRS Loop Protection feature in the BCF.
NOTE: Range description:
0 (not in use)
1 (in use)
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
0...1
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
0
Table 138
228
Flexi EDGE TRS Loop Protection Feature Usage
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Default value notes
not in use
Required on Creation
optional
Special value
not defined, not configured after S13 upgrade (255)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
FlexiEDGE TRS Loop Protection (118)
Related features
•
BSS30280: FlexiEDGE TRS Loop Protection
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EFM, EFC, EFO
MML Abbreviated Name
TRS4
MML Full Name
Flexi EDGE TRS Loop Protection feature usage
Segment Level Parameter
false
File Based Provisioning
supported
true
Table 138
8.42
Flexi EDGE TRS Loop Protection Feature Usage (Cont.)
FlexiEDGE Additional 2 E1/T1 (TRS2)
Parameter name
Flexi EDGE Additional 2 E1/T1 Feature Usage
Abbreviated name
flexiEdgeAdditional2E1T1Usage
Managed object
BCF
Multiplicity
1
Table 139
DN9813866
Base Control Function (BCF) radio network object parameters
Flexi EDGE Additional 2 E1/T1 Feature Usage
Id:0900d8058089b05e
Confidential
229
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you can enable the Flexi EDGE
Additional 2 E1/T1 feature in the BCF. Value zero
enables only 2 E1/T1 free interfaces. Value one
enables additional 2 E1/T1 interfaces, value two
enables two additional 2 E1/T1 interfaces and value
three enables three additional 2 E1/T1 interfaces.
NOTE: Range description:
0 (enabled 2 E1/T1 free interface)
1 (enabled additional 2 E1/T1 interface)
2 (enabled 2 additional 2 E1/T1 interface)
3 (enabled 3 additional 2 E1/T1 interface)
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
0...3
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
0
Default value notes
2 E1/T1 free interface enabled
Required on Creation
optional
Special value
not defined, not configured after S13 upgrade (255)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
FlexiEDGE Additional 2 E1/T1 (116)
Related features
•
BSS30285: FlexiEDGE Additional 2 E1/T1
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EFM, EFC, EFO
MML Abbreviated Name
TRS2
MML Full Name
FlexiEDGE Additional 2 E1/T1
Segment Level Parameter
false
Table 139
230
Flexi EDGE Additional 2 E1/T1 Feature Usage (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
File Based Provisioning
supported
Table 139
8.43
true
Flexi EDGE Additional 2 E1/T1 Feature Usage (Cont.)
header compression for ML-PPP (HECOP)
Parameter name
Header Compression For ML-PPP
Abbreviated name
headerCompressionForMlppp
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define whether the header
compression is used or not. For ML-PPP header
compression is regarded as optional so that it is
possible to instruct the network elements to work
with or without it.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
-
Range
OFF (0), ON (1)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
OFF ==> 0
ON ==> 1
Default value
OFF (0)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
Parameter can only be modified when BCF and
Abis HDLC links of the BCF are locked
Related parameters
abisInterfaceConnectionType of BCF - this parameter is valid only when BCF-abisInterfaceConnectionType is Packet Abis over TDM (1).
Parameter relationships
-
Related options
Packet Abis over TDM (151)
Table 140
DN9813866
Header Compression For ML-PPP
Id:0900d8058089b05e
Confidential
231
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Feature dependencies
BSS21440: Packet Abis over TDM
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
HECOP
MML Commands
EFM, EFO
MML Full Name
header compression for ML-PPP
Segment Level Parameter
-
Table 140
8.44
Header Compression For ML-PPP (Cont.)
header compression for UDP IP (HECOU)
Parameter name
Header Compression For UDP IP
Abbreviated name
headerCompressionForUdpIp
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define whether the header
compression is used or not. For UDP/IP headers
Header compression is regarded as optional so that
it is possible to instruct the network elements to
work with or without it.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
-
Range
OFF (0), ON (1)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
OFF ==> 0
ON ==> 1
Default value
OFF (0)
Default value notes
-
Table 141
232
Header Compression For UDP IP
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
Parameter can only be modified when BCF and
Abis HDLC links of the BCF are locked
Related parameters
abisInterfaceConnectionType of BCF - this parameter is valid only when BCF-abisInterfaceConnectionType is Packet Abis over TDM (1).
Parameter relationships
-
Related options
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
HECOU
MML Commands
EFM, EFO
MML Full Name
header compression for UDP IP
Segment Level Parameter
-
Table 141
8.45
identification of test equipment (TEST)
Parameter name
Identification Of Test Equipment
Abbreviated name
testEquipment
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the test equipment connected to the BCF. NOTE: The parameter is available for
2nd generation base stations and Talk-family of base stations. Parameter value RFTE is only allowed for 2nd generation base stations.
Additional information
-
Range
No Test Equipment (0), RFTE (1), STM (2)
Step
-
Unit
-
Table 142
DN9813866
Header Compression For UDP IP (Cont.)
Identification Of Test Equipment
Id:0900d8058089b05e
Confidential
233
Base Control Function (BCF) radio network object parameters
Formula for getting internal
value
BSS Radio Network Parameter Dictionary
gui ==> internal
No Test Equipment ==> 0
RFTE ==> 1
STM ==> 2
Default value
No Test Equipment (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
TEST
MML Full Name
identification of test equipment
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 142
8.46
IPSec enabled (IPSEC)
Parameter name
IPSec Enabled
Abbreviated name
ipSecEnabled
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define whether or not the
IPSec feature is enabled in BTS.
Table 143
234
Identification Of Test Equipment (Cont.)
IPSec Enabled
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
Disabled (0), Enabled (1)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
Disabled ==> 0
Enabled ==> 1
Default value
Disabled (0)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
-
Related parameters
abisInterfaceConnectionType of BCF - this parameter is valid and allowed only when BCF-abisInterfaceConnectionType is Packet Abis over Ethernet
(2).
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) and
Packet Abis security for BTS (152)
Feature dependencies
BSS21444: Packet Abis security
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
IPSEC
MML Commands
EFM, EFO
MML Full Name
IPSec enabled
Segment Level Parameter
-
Table 143
DN9813866
IPSec Enabled (Cont.)
Id:0900d8058089b05e
Confidential
235
Base Control Function (BCF) radio network object parameters
8.47
BSS Radio Network Parameter Dictionary
master clock BCF identification (MCBCF)
Parameter name
Master Clock BCF Identification
Abbreviated name
masterClockBcf
Managed object
BCF
Multiplicity
1
Description
With this parameter you add the slave BCF to a
chain under a master clock BCF in slave BCF creation.
NOTE: The parameter is only available for Talkfamily, MetroSite, UltraSite, Flexi EDGE, Flexi Multiradio, and BTSplus. See also parameter Slave BCF
List.
NetAct NOTE: If a master BCF and slave BCFs are
created to the BCF synchronisation chain in the
same RNW plan, the master BCF information
cannot be defined in the slave BCF data.
Additional information
-
Range
1..4400
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
optional
Special value
Not defined (0)
Related functions
-
Modification
Not modifiable
Modified
Adding the slave BCF to a chain under master clock
BCF can be done in slave BCF creation with this
parameter. The slave BCF can be defined when
creating or modifying the master clock BCF (see
parameter add BCF to chain (ADD)).
Related parameters
slaveBcfList of BCF - The slave BCF can be defined
when creating or modifying the master clock BCF.
Parameter relationships
-
Related options
-
Feature dependencies
•
Table 144
236
BSS21149: Flexi BSC
Master Clock BCF Identification
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
MML Commands
EFC, EFO, EFL
MML Abbreviated Name
MCBCF
MML Full Name
master clock BCF identification
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 144
8.48
Master Clock BCF Identification (Cont.)
master clock TRX (MCT)
Parameter name
Master Clock TRX
Abbreviated name
masterClock
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the master clock TRX for
the PrimeSite. The value 0 means that the site is not synchronised (a standalone site). NOTE: If there is more
than one TRX in the site, the site must be synchronised
(MCT<>0). See also the external synchronization source
parameter.
Additional information
-
Range
0...16
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Table 145
DN9813866
Base Control Function (BCF) radio network object parameters
Master Clock TRX
Id:0900d8058089b05e
Confidential
237
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
-
Related features
-
•
•
•
•
Interfaces
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EFM, EFO
MML Abbreviated Name
MCT
MML Full Name
master clock TRX
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 145
8.49
Master Clock TRX (Cont.)
maximum BTS multiplexing wait time (MBMWT)
Parameter name
Maximum BTS Multiplexing Wait Time
Abbreviated name
maxBtsMultiplexingWaitTime
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define the maximum multiplexing wait time on BTS.
NOTE:
Parameter is valid only for CS traffic.
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
2 rtsl (2), 4 rtsl (4), 8 rtsl (8)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
2 rtsl ==> 2
4 rtsl ==> 4
8 rtsl ==> 8
Default value
2 rtsl (2)
Default value notes
-
Table 146
238
Maximum BTS Multiplexing Wait Time
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MBMWT
MML Commands
EFM, EFO
MML Full Name
maximum BTS multiplexing wait time
Segment Level Parameter
-
Table 146
8.50
Maximum BTS Multiplexing Wait Time (Cont.)
maximum ETP multiplexing wait time (MEMWT)
Parameter name
Maximum ETP Multiplexing Wait Time
Abbreviated name
maxEtpMultiplexingWaitTime
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define the maximum multiplexing wait time on ETP.
NOTE:
Parameter is valid only for CS traffic.
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
Table 147
DN9813866
2 ms (2), 4 ms (4), 6 ms (6)
Maximum ETP Multiplexing Wait Time
Id:0900d8058089b05e
Confidential
239
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
2 ms ==> 2
4 ms ==> 4
6 ms ==> 6
Default value
2 ms (2)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MEMWT
MML Commands
EFM, EFO
MML Full Name
maximum ETP multiplexing wait time
Segment Level Parameter
-
Table 147
8.51
maximum multiplexing packet size (MMPS)
Parameter name
Maximum Multiplexing Packet Size
Abbreviated name
maximumMultiplexingPacketSize
3GPP name
-
Managed Object
BCF
Table 148
240
Maximum ETP Multiplexing Wait Time (Cont.)
Maximum Multiplexing Packet Size
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Multiplicity
1
Description
With this parameter you define the maximum multiplexing packet size.
NOTE:
This parameter defined value should be smaller or
equal than Ethernet Maximum Transfer Unit (This
parameter is located in platform side and MML
command is QRA).
NOTE:
Parameter is valid only for CS traffic.
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
160...1500
Step
10
Units
bytes
Formula for getting
internal value
internal_value =gui_value
Default value
300
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MMPS
MML Commands
EFM, EFO
MML Full Name
maximum multiplexing packet size
Table 148
DN9813866
Maximum Multiplexing Packet Size (Cont.)
Id:0900d8058089b05e
Confidential
241
Base Control Function (BCF) radio network object parameters
Segment Level Parameter
Table 148
8.52
BSS Radio Network Parameter Dictionary
-
Maximum Multiplexing Packet Size (Cont.)
MCPA identity number (MCPAIN)
Parameter name
MCPA Identity Number
Abbreviated name
mcpaIdentityNumber
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter identifies the multi-carrier power
amplifier unit by MCPA number.
The MCPA amplifies several TRXs and has limited
TX output power.
NOTE: The parameter is only shown in outputs.
Parameter is valid only for Flexi Multiradio site type.
Additional information
Range
0... 255
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
Not defined
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Flexible MCPA TX Power Pooling (169)
Feature dependencies
BSS21507 Flexible MCPA TX Power Pooling
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
Table 149
242
MCPA Identity Number
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
MML Abbreviated Name
MCPAIN
MML Commands
EFO
MML Full Name
MCPA identity number
Segment Level Parameter
-
Table 149
8.53
Base Control Function (BCF) radio network object parameters
MCPA Identity Number (Cont.)
MCPA identity port id (MCPAIP)
Parameter name
MCPA Identity Port ID
Abbreviated name
mcpaIdentityPortId
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter identifies the multi-carrier power
amplifier unit by MCPA port number. The MCPA
amplifies several TRXs and has limited TX output
power.
NOTE: The parameter is only shown in outputs.
Parameter is valid only for Flexi Multiradio site type.
Additional information
Range
0... 255
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
Not defined
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Flexible MCPA TX Power Pooling (169)
Feature dependencies
BSS21507 Flexible MCPA TX Power Pooling
Interfaces
BSC -> RAC
Table 150
DN9813866
MCPA Identity Port ID
Id:0900d8058089b05e
Confidential
243
Base Control Function (BCF) radio network object parameters
References
-
File based provisioning
supported
false
MML Abbreviated Name
MCPAIP
MML Commands
EFO
MML Full Name
MCPA identity port id
Segment Level Parameter
-
Table 150
8.54
BSS Radio Network Parameter Dictionary
MCPA Identity Port ID (Cont.)
MCPA identity position (MCPAIS)
Parameter name
MCPA Identity Position
Abbreviated name
mcpaIdentityPosition
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter identifies the multi-carrier power
amplifier unit by MCPA position number. The
MCPA amplifies several TRXs and has limited TX
output power.
NOTE: The parameter is only shown in outputs.
Parameter is valid only for Flexi Multiradio site type.
Additional information
Range
0... 255
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
Not defined
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Table 151
244
MCPA Identity Position
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Related options
Flexible MCPA TX Power Pooling (169)
Feature dependencies
BSS21507 Flexible MCPA TX Power Pooling
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
MCPAIS
MML Commands
EFO
MML Full Name
MCPA identity position
Segment Level Parameter
-
Table 151
8.55
Base Control Function (BCF) radio network object parameters
MCPA Identity Position (Cont.)
MCPA power (MCPAPW)
Parameter name
MCPA Power
Abbreviated name
mcpaPower
3GPP name
-
Managed Object
BCF
Multiplicity
-
Description
With this parameter you define the maximum multiplexing packet size.
NOTE:
This parameter defined value should be smaller or
equal than Ethernet Maximum Transfer Unit (This
parameter is located in platform side and MML
command is QRA).
NOTE:
Parameter is valid only for CS traffic.
Additional information
Range
0... 80000
Step
1
Units
mW
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
Not defined
Table 152
DN9813866
MCPA Power
Id:0900d8058089b05e
Confidential
245
Base Control Function (BCF) radio network object parameters
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Flexible MCPA TX Power Pooling (169)
Feature dependencies
BSS21507 Flexible MCPA TX Power Pooling
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
MCPAPW
MML Commands
EFO
MML Full Name
MCPA power
Segment Level Parameter
-
Table 152
8.56
BSS Radio Network Parameter Dictionary
MCPA Power (Cont.)
MCPA power pooling bcf status (MCPABS)
Parameter name
MCPA Power Pooling BCF Status
Abbreviated name
mcpaPowerPoolingBCFStatus
3GPP name
-
Managed Object
BCF
Multiplicity
-
Description
This parameter defines if the Flexible MCPA TX
Power Pooling feature is enabled in the BTS site in
the SCF.
NOTE: The parameter is only shown in outputs.
Parameter is valid only for Flexi Multiradio site type.
Additional information
Range
MCPA TX Power pooling disabled at the BTS site
(0), MCPA TX Power pooling enabled at the BTS
site (1)
Step
-
Units
-
Table 153
246
MCPA Power Pooling BCF Status
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
gui ==> internal
MCPA TX Power pooling disabled at the BTS site
==> 0
MCPA TX Power pooling enabled at the BTS site
==> 1
Default value
MCPA TX Power pooling disabled at the BTS site
(0)
Default value notes
-
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Flexible MCPA TX Power Pooling (169)
Feature dependencies
BSS21507 Flexible MCPA TX Power Pooling
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
MCPABS
MML Commands
EFO
MML Full Name
MCPA power pooling bcf status
Segment Level Parameter
-
Table 153
8.57
MCPA Power Pooling BCF Status (Cont.)
MCPA power pooling enabled (MCPAEN)
Parameter name
MCPA Power Pooling Enabled
Abbreviated name
mcpaPowerPoolingEnabled
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you can enable the Flexible
MCPA TX Power Pooling feature in the BCF.
Parameter is valid only for Flexi Multiradio site type.
Table 154
DN9813866
MCPA Power Pooling Enabled
Id:0900d8058089b05e
Confidential
247
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Additional information
Range
MCPA TX Power Pooling disabled (0), MCPA TX
Power Pooling enabled (1)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
MCPA TX Power pooling disabled ==> 0
MCPA TX Power pooling enabled ==> 1
Default value
MCPA TX Power pooling disabled (0)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Flexible MCPA TX Power Pooling (169)
Feature dependencies
BSS21507 Flexible MCPA TX Power Pooling
Interfaces
•
•
References
-
File based provisioning
supported
-
MML Abbreviated Name
MCPAEN
MML Commands
EFM, EFO
MML Full Name
MCPA power pooling enabled
Segment Level Parameter
-
Table 154
8.58
MCPA Power Pooling Enabled (Cont.)
OMUSIG priority ()
Parameter name
OMUSIG Priority
Abbreviated name
omusigPriority
3GPP name
-
Managed Object
BCF
Table 155
248
BSC <-> RAC
RAC <-> RACApp
OMUSIG Priority
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Multiplicity
1
Description
With this parameter BSC keeps information about
OMUSIG priority info of the BTS. This parameter
has meaning only in conflicting OMUSIGs situation
to help operator in selecting right BCF.
Only system can modify this parameter.
MML NOTE:
The parameter is only shown in outputs.
Additional information
-
Range
0...32
Step
1
Units
-
Formula for getting
internal value
internal_value =
Default value
255
Default value notes
Not defined
Special value
Not defined (255)
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Flexi BTS Autoconnection (143)
Feature dependencies
BSS21316: Flexi BTS Autoconnection
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
-
MML Commands
EEB
MML Full Name
OMUSIG priority
Segment Level Parameter
-
Table 155
DN9813866
gui_value
OMUSIG Priority (Cont.)
Id:0900d8058089b05e
Confidential
249
Base Control Function (BCF) radio network object parameters
8.59
BSS Radio Network Parameter Dictionary
Packet Abis BCF Group ID (PABGID)
Parameter name
Packet Abis BCF Group ID
Abbreviated name
packetAbisBcfGroupId
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With the parameter you can define the Identifier of
the Packet Abis BCF Group for the the BCF. The
Packet Abis BCF Group delimits a group of BCFs
among which local switching or Packet Abis
IP/TDM Aggregation is possible.
MML Range:
0..3000
Value 0 (Intra-BCF LS Enabled) indicates that only
intra-BCF Local switching is possible for the BCF.
Parameter is valid only if the ABIS connection type
(AICT) is other than Legacy Abis
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
If Packet Abis BCF Group is given without the abis
connection type, then the abis connection type will
be one associated with that Packet Abis BCF
Group.
Range
0...3000
Step
1
Units
-
Formula for getting
internal value
internal_value = gui_value
Default value
65535
Default value notes
Not used
Special value
Not used (65535)
Required on creation
optional
Modification
Requires object locking
Table 156
250
Packet Abis BCF Group ID
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Modified
Modification of the Packet Abis BCF Group ID
parameter requires locking the Packet Abis over
TDM BCF,Packet Abis over Ethernet – TDM BCF
and Packet Abis over Ethernet – TDM (LS) BCF.
Modifcation from value 'Intra-BCF LS enabled' to
'not used' and vice versa can be done online.
Packet Abis over IP/Eth BCF can be modified
always online.
Related parameters
abisInterfaceConnectionType of
BCF - This parameter Packet Abis BCF Group is
not used, if parameter Abis Interface Connection
Type value is Legacy Abis
Parameter relationships
-
Related options
•
Local Switching for Packet Abis (156)
(optional) AND ( Packet Abis over TDM (151)
(optional) OR Packet Abis over IP/Eth (150)
(optional) ) OR Packet Abis over TDM (151)
(optional) AND Packet Abis IP/TDM Aggregation (163) (optional)
Feature dependencies
•
AggregationBSS21327 Local Switching For
Packet Abis (standard)
BSS21539 Packet Abis IP/TDM Aggregation
(standard)
•
Interfaces
•
•
References
-
File based provisioning
supported
false
MML Abbreviated Name
PABGID
MML Commands
EFC, EFM, EFO
MML Full Name
Packet Abis BCF Group ID
Segment Level Parameter
-
Table 156
8.60
Packet Abis BCF Group ID (Cont.)
PCM port ID 0 (PORT0)
Parameter name
PCM Port ID 0
Abbreviated name
pcmPortId0
Managed object
BCF
Table 157
DN9813866
BSC <-> RAC
RAC <-> RACApp
PCM Port ID 0
Id:0900d8058089b05e
Confidential
251
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Multiplicity
1
Description
With this parameter you identify the BSC PCM used
in BTS Abis Port 0 in BTSplus and Horizon BTS.
PCM of TRX is defined in TRX creation.
Parameter is valid only for BTSplus and Horizon
site type.
NOTE: At least one of PCM port ID parameters
must be given for BTSplus and Horizon BTS.
Additional information
-
Range
0...3559
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
PCM port is not used (65535)
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS21469: BS2xx@Flexi BSC product family
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification.
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
PORT0
MML Full Name
PCM port ID 0
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 157
252
PCM Port ID 0 (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
8.61
Base Control Function (BCF) radio network object parameters
PCM port ID 1 (PORT1)
Parameter name
PCM Port ID 1
Abbreviated name
pcmPortId1
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the BSC PCM used
in BTS Abis Port 1 in BTSplus and Horizon BTS.
PCM of TRX is defined in TRX creation.
Parameter is valid only for BTSplus and Horizon
BTS.
NOTE: At least one of PCM port ID parameters
must be given for BTSplus and Horizon BTS.
Additional information
-
Range
0...3559
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
PCM port is not used (65535)
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS21469: BS2xx@Flexi BSC product family
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification.
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
PORT1
Table 158
DN9813866
PCM Port ID 1
Id:0900d8058089b05e
Confidential
253
Base Control Function (BCF) radio network object parameters
MML Full Name
PCM port ID 1
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 158
8.62
BSS Radio Network Parameter Dictionary
PCM Port ID 1 (Cont.)
PCM port ID 2 (PORT2)
Parameter name
PCM Port ID 2
Abbreviated name
pcmPortId2
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the BSC PCM used
in BTS Abis Port 2 in BTSplus and Horizon BTS.
PCM of TRX is defined in TRX creation.
Parameter is valid only for BTSplus and Horizon
BTS.
NOTE: At least one of PCM port ID parameters
must be given for BTSplus and Horizon BTS.
Additional information
-
Range
0...3559
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
PCM port is not used (65535)
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
Table 159
254
BSS21469: BS2xx@Flexi BSC product family
PCM Port ID 2
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Interfaces
•
•
References
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification.
BSC <-> RAC
RAC <-> RACApp
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
PORT2
MML Full Name
PCM port ID 2
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 159
8.63
PCM Port ID 2 (Cont.)
PCM port ID 3 (PORT3)
Parameter name
PCM Port ID 3
Abbreviated name
pcmPortId3
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the BSC PCM used
in BTS Abis Port 3 in BTSplus and Horizon BTS.
PCM of TRX is defined in TRX creation.
Parameter is valid only for BTSplus and Horizon
BTS.
NOTE: At least one of PCM port ID parameters
must be given for BTSplus and Horizon BTS.
Additional information
-
Range
0...3559
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
PCM port is not used (65535)
Table 160
DN9813866
PCM Port ID 3
Id:0900d8058089b05e
Confidential
255
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS21469: BS2xx@Flexi BSC product family
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification.
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
PORT3
MML Full Name
PCM port ID 3
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 160
8.64
PCM Port ID 3 (Cont.)
PCM port ID 4 (PORT4)
Parameter name
PCM Port ID 4
Abbreviated name
pcmPortId4
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the BSC PCM used
in BTS Abis Port 4 in BTSplus and Horizon BTS.
PCM of TRX is defined in TRX creation.
Parameter is valid only for BTSplus and Horizon
BTS.
NOTE: At least one of PCM port ID parameters
must be given for BTSplus and Horizon BTS.
Additional information
-
Range
0...3559
Step
1
Table 161
256
PCM Port ID 4
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
PCM port is not used (65535)
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
BSS21469: BS2xx@Flexi BSC product family
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification.
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
PORT4
MML Full Name
PCM port ID 4
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 161
8.65
PCM port ID 5 (PORT5)
Parameter name
PCM Port ID 5
Abbreviated name
pcmPortId5
Managed object
BCF
Multiplicity
1
Table 162
DN9813866
PCM Port ID 4 (Cont.)
PCM Port ID 5
Id:0900d8058089b05e
Confidential
257
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you identify the BSC PCM used
in BTS Abis Port 5 in BTSplus and Horizon BTS.
PCM of TRX is defined in TRX creation.
Parameter is valid only for BTSplus and Horizon
BTS.
NOTE: At least one of PCM port ID parameters
must be given for BTSplus and Horizon BTS.
Additional information
-
Range
0...3559
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
PCM port is not used (65535)
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS21469: BS2xx@Flexi BSC product family
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification.
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
PORT5
MML Full Name
PCM port ID 5
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 162
258
PCM Port ID 5 (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
8.66
Base Control Function (BCF) radio network object parameters
PCM port ID 6 (PORT6)
Parameter name
PCM Port ID 6
Abbreviated name
pcmPortId6
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the BSC PCM used
in BTS Abis Port 6 in BTSplus and Horizon BTS.
PCM of TRX is defined in TRX creation.
Parameter is valid only for BTSplus and Horizon
BTS.
NOTE: At least one of PCM port ID parameters
must be given for BTSplus and Horizon BTS.
Additional information
-
Range
0...3559
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
PCM port is not used (65535)
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
BSS21469: BS2xx@Flexi BSC product family
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification.
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
PORT6
Table 163
DN9813866
PCM Port ID 6
Id:0900d8058089b05e
Confidential
259
Base Control Function (BCF) radio network object parameters
MML Full Name
PCM port ID 6
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 163
8.67
BSS Radio Network Parameter Dictionary
PCM Port ID 6 (Cont.)
PCM port ID 7 (PORT7)
Parameter name
PCM Port ID 7
Abbreviated name
pcmPortId7
Managed object
BCF
Multiplicity
1
Description
With this parameter you identify the BSC PCM used
in BTS Abis Port 7 in BTSplus and Horizon BTS.
PCM of TRX is defined in TRX creation.
Parameter is valid only for BTSplus and Horizon
BTS.
NOTE: At least one of PCM port ID parameters
must be given for BTSplus and Horizon BTS.
Additional information
-
Range
0...3559
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
PCM port is not used (65535)
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
Table 164
260
BSS21469: BS2xx@Flexi BSC product family
PCM Port ID 7
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Interfaces
•
•
References
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification.
BSC <-> RAC
RAC <-> RACApp
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
PORT7
MML Full Name
PCM port ID 7
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 164
8.68
PCM Port ID 7 (Cont.)
polarity (POL)
Parameter name
Polarity
Abbreviated name
polarity
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the actual polarity of
the external input connection.
NOTE: The parameter is only available for MetroSite, UltraSite, Flexi EDGE and Flexi Multiradio.
Additional information
-
Range
Closed (0), Open (1)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Closed ==> 0
Open ==> 1
Default value
Open (1)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Table 165
DN9813866
Polarity
Id:0900d8058089b05e
Confidential
261
Base Control Function (BCF) radio network object parameters
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
References
-
MML Commands
EFX, EFO
MML Abbreviated Name
POL
MML Full Name
polarity
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 165
8.69
BSS Radio Network Parameter Dictionary
RAC <-> RACApp
RAC <-> BSC
Polarity (Cont.)
packet abis congestion control (PACC)
Parameter name
Packet Abis Congestion Control
Abbreviated name
packetAbisCongestionControl
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define is Packet Abis congestion control procedure allowed. This concerns
both Abis backhaul monitor and Abis Packet loss
detection
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
Disabled (0), Enabled (1)
Step
-
Units
-
Table 166
262
Packet Abis Congestion Control
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
gui ==> internal
Disabled ==> 0
Enabled ==> 1
Default value
Disabled (0)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
ulCommittedInformationRate of BCF - UL Committed Information Rate parameter has to be defined
before packetAbisCongestionControl can be
enabled.
dlCommittedInformationRate of BCF - Downlink
Committed Information Rate parameter has to be
defined before packetAbisCongestionControl can
be enabled.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
PACC
MML Commands
EFM, EFO
MML Full Name
packet abis congestion control
Segment Level Parameter
-
Table 166
8.70
Packet Abis over Satellite in use ()
Parameter name
Packet Abis Over Satellite in Use
Abbreviated name
paSatelliteUse
Table 167
DN9813866
Packet Abis Congestion Control (Cont.)
Packet Abis Over Satellite in Use
Id:0900d8058089b05e
Confidential
263
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter is informed if BCF is using Satellite Packet Abis connection. This is only output
parameter. System initializes the parameter
depending on OMUISIG's SCTP association
parameter 'initial RTO'.
MML NOTE:
The parameter is only shown in outputs
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
BCF is not using satellite Packet Abis connection
(0), BCF is using satellite Packet Abis connection
(1)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
BCF is not using satellite Packet Abis connection
==> 0
BCF is using satellite Packet Abis connection ==> 1
Default value
BCF is not using satellite Packet Abis connection
(0)
Default value notes
-
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
BSC -> RAC
References
-
Table 167
264
Packet Abis Over Satellite in Use (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
File based provisioning
supported
false
MML Abbreviated Name
-
MML Commands
EFO
MML Full Name
Packet Abis over Satellite in use
Segment Level Parameter
-
Table 167
8.71
Base Control Function (BCF) radio network object parameters
Packet Abis Over Satellite in Use (Cont.)
packet delay variation (PVD)
Parameter name
Packet Delay Variation
Abbreviated name
packetDelayVariation
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter user can define the packet
delay variation. Packet Delay Variation is used to
determine the de-jitter buffering in ETP and BTS.
Additional information
-
Range
0...100000
Step
500
Units
microsec
Formula for getting
internal value
internal_value =gui_value
Default value
5000
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS21440: Packet Abis over TDM
Table 168
DN9813866
Packet Delay Variation
Id:0900d8058089b05e
Confidential
265
Base Control Function (BCF) radio network object parameters
Interfaces
BSS Radio Network Parameter Dictionary
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
PVD
MML Commands
EFM, EFO
MML Full Name
packet delay variation
Segment Level Parameter
-
Table 168
8.72
packet loss on DL Abis PL1 threshold (PL1)
Parameter name
Packet Loss on DL Abis PL1 Threshold
Abbreviated name
pl1ThresholdPacketLoss
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define the PL1 threshold
value related to the percentage of the lost frames in
the PSN compared to the corresponding expected
frames (lost frames + received frames). Considering the Packet Loss Congestion definition, the
proper reaction procedure is triggered when the difference between the PS loss frame rate and CS
loss frame rate is higher than PL1 threshold.
Table 169
266
Packet Delay Variation (Cont.)
Packet Loss on DL Abis PL1 Threshold
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Additional information
Base Control Function (BCF) radio network object parameters
NOTE:
Range: 1 -> 10exp (-4)
2 -> 2x10exp (-4)
3 -> 3x10exp (-4)
4 -> 4x10exp (-4)
5 -> 5x10exp (-4)
6 -> 6x10exp (-4)
7 -> 7x10exp (-4)
8 -> 8x10exp (-4)
9 -> 9x10exp (-4)
10 -> 10exp (-3)
11 -> 2x10exp (-3)
12 -> 3x10exp (-3)
13 -> 4x10exp (-3)
14 -> 5x10exp (-3)
15 -> 6x10exp (-3)
16 -> 7x10exp (-3)
17 -> 8x10exp (-3)
18 -> 9x10exp (-3)
19 -> 10x10exp (-3)
20 -> 2x10exp (-2)
21 -> 3x10exp (-2)
22 -> 4x10 exp (-2)
23 -> 5x10 exp (-2)
24 -> 6x10exp (-2)
25 -> 7x10exp (-2)
26 -> 8x10exp (-2)
27 -> 9x10exp (-2)
28 -> 10exp (-2)
29 -> 2x10exp (-1)
30 -> 3x10exp (-1)
31 -> 4x10exp (-1)
32 -> 5x10exp (-1)
Default: 14 -> 5x10 exp (-3)
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Table 169
DN9813866
Packet Loss on DL Abis PL1 Threshold (Cont.)
Id:0900d8058089b05e
Confidential
267
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Range
1...32
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
14
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
pl2ThresholdPacketLoss of BCF - Value of PL2
Threshold Packet Loss (PL2) parameter must be
bigger than PL1 Threshold Packet Loss (PL1)
parameter
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
PL1
MML Commands
EFM, EFO
MML Full Name
packet loss on DL Abis PL1 threshold
Segment Level Parameter
-
Table 169
8.73
packet loss on DL Abis PL2 threshold (PL2)
Parameter name
Packet Loss on DL Abis PL2 Threshold
Abbreviated name
pl2ThresholdPacketLoss
3GPP name
-
Table 170
268
Packet Loss on DL Abis PL1 Threshold (Cont.)
Packet Loss on DL Abis PL2 Threshold
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define the PL2 threshold
value related to the percentage of the lost frames in
the PSN compared to the corresponding expected
frames (lost frames + received frames). Considering the Packet Loss Congestion definition, the
proper reaction procedure is triggered when the difference between the PS loss frame rate and CS
loss frame rate is higher than PL2 threshold.
Table 170
DN9813866
Base Control Function (BCF) radio network object parameters
Packet Loss on DL Abis PL2 Threshold (Cont.)
Id:0900d8058089b05e
Confidential
269
Base Control Function (BCF) radio network object parameters
Additional information
BSS Radio Network Parameter Dictionary
NOTE:
Range:
1 -> 10exp (-4)
2 -> 2x10exp (-4)
3 -> 3x10exp (-4)
4 -> 4x10exp (-4)
5 -> 5x10exp (-4)
6 -> 6x10exp (-4)
7 -> 7x10exp (-4)
8 -> 8x10exp (-4)
9 -> 9x10exp (-4)
10 -> 10exp (-3)
11 -> 2x10exp (-3)
12 -> 3x10exp (-3)
13 -> 4x10exp (-3)
14 -> 5x10exp (-3)
15 -> 6x10exp (-3)
16 -> 7x10exp (-3)
17 -> 8x10exp (-3)
18 -> 9x10exp (-3)
19 -> 10x10exp (-3)
20 -> 2x10exp (-2)
21 -> 3x10exp (-2)
22 -> 4x10 exp (-2)
23 -> 5x10 exp (-2)
24 -> 6x10exp (-2)
25 -> 7x10exp (-2)
26 -> 8x10exp (-2)
27 -> 9x10exp (-2)
28 -> 10exp (-2)
29 -> 2x10exp (-1)
30 -> 3x10exp (-1)
31 -> 4x10exp (-1)
32 -> 5x10exp (-1)
Default: 28 -> 10exp (-2)
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Table 170
270
Packet Loss on DL Abis PL2 Threshold (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Range
1...32
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
28
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
pl1ThresholdPacketLoss of BCF - Value of PL2
Threshold Packet Loss (PL2) parameter must be
bigger than PL1 Threshold Packet Loss (PL1)
parameter.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
PL2
MML Commands
EFM, EFO
MML Full Name
packet loss on DL Abis PL2 threshold
Segment Level Parameter
-
Table 170
8.74
packet TRS E1/T1 usage (TRS5)
Parameter name
Packet TRS E1/T1 Feature Usage
Abbreviated name
packetTrsE1T1Usage
3GPP name
-
Table 171
DN9813866
Packet Loss on DL Abis PL2 Threshold (Cont.)
Packet TRS E1/T1 Feature Usage
Id:0900d8058089b05e
Confidential
271
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Managed Object
BCF
Multiplicity
1
Description
With this parameter you can enable Packet TRS
E1/T1 feature in the BCF. It is possible to enable 13 E1/T1interfaces and connect UltraSite / BTSPlus
site types via Flexi EDGE/Flexi Multiradio.
NOTE: The parameter is available for Flexi EDGE
and Flexi Multiradio.
Additional information
-
Range
0...4
Step
1
Units
-
Formula for getting
internal value
internal_value =
Default value
0
Default value notes
not in use
Special value
Not defined. Not configured after S15 upgrade
(255)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet TRS E1/T1 (154) (optional) AND ( Packet
Abis over IP/Eth (150) (optional) OR Packet Abis
over TDM (151) (optional) )
Feature dependencies
BSS21440: Packet Abis over TDM
gui_value
BSS21454: Packet Abis over IP/Eth
BSS21443: Packet TRS for UltraSite/BTSPlus
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
TRS5
MML Commands
EFM, EFO
MML Full Name
packet TRS E1/T1 usage
Table 171
272
Packet TRS E1/T1 Feature Usage (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Segment Level Parameter
Table 171
8.75
-
Packet TRS E1/T1 Feature Usage (Cont.)
QoS aware ethernet switch usage (QOSA)
Parameter name
QoS Aware Ethernet Switch Usage
Abbreviated name
qosAwareEthSwitchUsage
Managed object
BCF
Multiplicity
1
Description
With this parameter you can enable QoS Aware
Ethernet Switching feature in BTS.
This parameter is supported only for Flexi Edge and
FlexiMultiradio site types.
Additional information
-
Range
Disabled (0), Enabled (1)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Disabled ==> 0
Enabled ==> 1
Default value
Disabled (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
QoS Aware Ethernet Switching (170)
Related features
•
BSS101417 QoS aware Ethernet Switching
Interfaces
•
•
BSC -> RAC
RAC <-> RACApp
References
-
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
QOSA
Table 172
DN9813866
QoS Aware Ethernet Switch Usage
Id:0900d8058089b05e
Confidential
273
Base Control Function (BCF) radio network object parameters
MML Full Name
QoS aware ethernet switch usage
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 172
8.76
BSS Radio Network Parameter Dictionary
QoS Aware Ethernet Switch Usage (Cont.)
RF sharing state (RFSS)
Parameter name
RF Sharing State
Abbreviated name
rfSharingState
Managed object
BCF
Multiplicity
1
Description
This parameter defines if the BCF RF is shared and
if the GSM is master or slave technology of the RF
resources. Parameter is valid only for Flexi Multiradio BTS.
Additional information
-
Range
•
•
•
Step
-
Unit
-
Formula for getting
internal value
-
Default value
0 (off / Not shared)
Default value notes
-
Required on Creation
Value set by the system
Related functions
-
Modification
not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
•
Table 173
274
0 (off / Not shared)
1 (RF master)
2 (RF slave)
BSS101688 BSC SUPPORT FOR FLEXI MULTIRADIO 10 BTS
BSS21403 Flexi Multiradio TRX HW Activation
RF Sharing State
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Interfaces
•
BSC -> RAC
References
•
BSS101688 BSC SUPPORT FOR FLEXI MULTIRADIO 10 BTS
BSS21403 Flexi Multiradio TRX HW Activation
•
MML Commands
EFO
MML Abbreviated Name
RFSS
MML Full Name
RF sharing state
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 173
8.77
RF Sharing State (Cont.)
route (ROU)
Parameter name
Route
Abbreviated name
reportingRoute
Managed object
BCF
Multiplicity
1
Description
With this parameter you activate the routing of the
input alarm and choose where the alarm will be
sent.
NOTE: The parameter is only available for MetroSite, UltraSite, Flexi EDGE and Flexi Multiradio.
NOTE: MML RANGE:
NOT (not activated (not reported)),
ACT (activated (reported to the BSC as a normal
external alarm)),
TMS (activated (reported as a transmission alarm
to the Transmission Management System)),
MAINS (activated (reported to the BSC as a Mains
Breakdownalarm))
Additional information
-
Range
NOT (0), ACT (1), TMS (2), MAINS (3)
Step
-
Unit
-
Table 174
DN9813866
Route
Id:0900d8058089b05e
Confidential
275
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
BSS Radio Network Parameter Dictionary
gui ==> internal
NOT ==> 0
ACT ==> 1
TMS ==> 2
MAINS ==> 3
Default value
NOT (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
References
-
MML Commands
EFX, EFO
MML Abbreviated Name
ROU
MML Full Name
route
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 174
8.78
Route (Cont.)
RX difference limit (RXDL)
Parameter name
RX Difference Limit
Abbreviated name
rxDifferenceLimit
Managed object
BCF
Multiplicity
1
Table 175
276
RAC <-> RACApp
RAC <-> BSC
RX Difference Limit
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Description
With this parameter you define the value limit for
activating the RX alarm.
NOTE: For site types 2nd generation, MetroSite,
UltraSite, Flexi EDGE, BTSplus and Flexi Multiradio the value 64 dB indicates that no RX alarms are
set.
Additional information
-
Range
3...64
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
10 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
•
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
RXDL
MML Full Name
RX difference limit
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 175
DN9813866
RX Difference Limit (Cont.)
Id:0900d8058089b05e
Confidential
277
Base Control Function (BCF) radio network object parameters
8.79
BSS Radio Network Parameter Dictionary
SDCCH LAPDm T200 (T200S)
Parameter name
SDCCH LAPDm T200
Abbreviated name
T200S
Managed object
BCF
Multiplicity
1
Description
The parameter determines a LAPDm T200 for
supervision of the SDCCH message transfer from
BTS to mobile.
MMI is the only user interface supporting this
parameter.
The parameter is modifiable only for Talk-family,
UltraSite, Flexi EDGE, BTSplus, Flexi Multiradio
and Horizon BTSs.
NOTE: MML modification: Online
Additional information
-
Range
220...1260
Step
20
Unit
ms
Formula for getting
internal value
internal_value = gui_value / 20
Default value
0 ms
Default value notes
0 ms (BCF predefined value)
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
Interfaces
-
References
-
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
T200S
MML Full Name
SDCCH LAPDm T200
Table 176
278
BSS20924: BSC Support for LAPDm T200
Setting
SDCCH LAPDm T200
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 176
8.80
Base Control Function (BCF) radio network object parameters
SDCCH LAPDm T200 (Cont.)
severity (SEV)
Parameter name
Severity
Abbreviated name
severity
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the severity of the
input alarm.
NOTE: The parameter is only available for MetroSite, UltraSite, Flexi EDGE and Flexi Multiradio.
NOTE: MML Range:
AL3 (The highest alarm level),
AL2 (The medium alarm level),
AL1 (The lowest alarm level)
NOTE: MML default: AL1
Additional information
-
Range
Critical (1), Major (2), Minor (3)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Critical ==> 1
Major ==> 2
Minor ==> 3
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 177
DN9813866
Severity
Id:0900d8058089b05e
Confidential
279
Base Control Function (BCF) radio network object parameters
Related options
-
Related features
-
Interfaces
•
•
References
-
MML Commands
EFX, EFO
MML Abbreviated Name
SEV
MML Full Name
severity
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 177
8.81
RAC <-> RACApp
RAC <-> BSC
Severity (Cont.)
site type (TYPE)
Parameter name
Site Type
Abbreviated name
bcfType
Managed object
BCF
Multiplicity
1
Table 178
280
BSS Radio Network Parameter Dictionary
Site Type
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Description
Base Control Function (BCF) radio network object parameters
With this parameter you identify the type of the BTS
site.
NOTE:
Modification of the BTS site type is possible only
between the 2nd generation and Talk-family site
types and from the 2nd generation or Talk-family
site types to UltraSite site and Talk-family or UltraSite site types to Flexi EDGE type. The modification
from the UltraSite or Flexi EDGE back to the 2nd
generation or Talk-family site types is not possible.
Modification between BTSplus and other site types
is not possible.
Modification from UltraSite or Flexi EDGE site type
to Flexi Multiradio BTS site type is possible but not
vice versa.
Modification from UltraSite, Flexi EDGE,Flexi Multiradio or Flexi Compact site type to Flexi Multiradio
10 BTS site type is possible but not vice versa.
Modification from UltraSite, Flexi EDGE or Flexi
Multiradio site type to Flexi Compact BTS site type
is possible but not vice versa.
It is not allowed to modify the BTS site type of
Horizon BTS to any other or any other BTS site type
to Horizon BTS.
MML NOTE:
B (2nd Generation),
D (Talk-family),
F (PrimeSite),
C (MetroSite),
I (InSite),
P (UltraSite),
E (Flexi EDGE <option>),
X (BTSplus),
M (Flexi Multiradio <option>)
NOTE:
Flexi EDGE is available only when the Flexi EDGE
licence state is ON or CONFIG. Flexi Multiradio is
available only when the Flexi Multiradio TRX HW
Activation licence state is ON or CONFIG.
Additional information
Table 178
DN9813866
-
Site Type (Cont.)
Id:0900d8058089b05e
Confidential
281
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Range
2nd Generation (0), Talk-family (1), PrimeSite (2),
MetroSite (3), InSite (4), UltraSite (5), Flexi EDGE
(6), BTSplus (7), Flexi Multiradio (8), Horizon (9)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
2nd Generation ==> 0
Talk-family ==> 1
PrimeSite ==> 2
MetroSite ==> 3
InSite ==> 4
UltraSite ==> 5
Flexi EDGE ==> 6
BTSplus ==> 7
Flexi Multiradio ==> 8
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Requires object locking
Modified
When BCF is locked. The OMU link of the BCF
cannot be in working state when the BTS site type
is modified to UltraSite.
Related parameters
BCF-btsSiteSubtype- If Site Type is BTSplus or
Flexi Multiradio, then BTS Site Subtype parameter
is used.
Parameter relationships
When bcfType is BTSplus or Flexi Multiradio.
Related options
-
Related features
•
•
•
BSS21469: BS2xx@Flexi BSC product family
BSS21403: Flexi Multiradio TRX HW Activation
Support for Horizon BTS Family in Flexi BSC
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
Table 178
282
Site Type (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
References
NSN reference: Gemini Support (BTSplus)
NSN reference: BSS21403 Flexi Multiradio TRX
HW Activation.
NSN reference: Support for Horizon BTS Family in
Flexi BSC Implementation Specification.
MML Commands
EFC, EFM, EFO, EEI
MML Abbreviated Name
TYPE
MML Full Name
site type
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 178
8.82
Site Type (Cont.)
synch enabled (SENA)
Parameter name
Synch Enabled
Abbreviated name
synchEnabled
Managed object
BCF
Multiplicity
1
Description
With this parameter you enable the synchronization
of the chain of the independent mode BCFs. It is
possible to enable the synchronization of the chain
when creating or modifying the master clock BCF.
Modification of the parameter requires locking of all
of the BCFs of the chain when Synch Enabled is
modified from Yes to No. When modifying an independent mode BCF, the modification requires
locking of the BCF.
NOTE:
The parameter is only available for Talk-family,
MetroSite, UltraSite, Flexi EDGE and Flexi Multiradio.
Additional information
-
Range
Synch disabled (F) (0), Synch enabled (T) (1)
Step
-
Unit
-
Table 179
DN9813866
Synch Enabled
Id:0900d8058089b05e
Confidential
283
Base Control Function (BCF) radio network object parameters
Formula for getting
internal value
BSS Radio Network Parameter Dictionary
gui ==> internal
Synch disabled (F) ==> 0
Synch enabled (T) ==> 1
Default value
Synch disabled (F) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Requires object locking
Modified
Modification of the parameter requires locking of all
of the BCFs of the chain when Synch Enabled is
modified from Yes to No. If value of the parameter
is modifed from No to Yes, then the modification
requires locking of the BCF. When modifying an
independent mode BCF, the modification requires
locking of the BCF.
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
MML Commands
EFC, EFM, EFO, EFL
MML Abbreviated Name
SENA
MML Full Name
synch enabled
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 179
8.83
Synchronization Mode (SM)
Parameter name
Synch Status
Abbreviated name
synchStatus
Managed object
BCF
Multiplicity
1
Table 180
284
Synch Enabled (Cont.)
Synch Status
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Description
This parameter indicates the synchronisation mode
of the BCF.
NOTE: The parameter is only available for Talkfamily, MetroSite, UltraSite, Flexi EDGE, Flexi Multiradio and BTSplus. Value 5 (NETWORK) is supported only by Flexi Multiradio 10.
MML NOTE: MML range:
UNSYNCH,
SYNCH,
LMUSYNCH,
ABISSYNCH (SYNCH include INDEPENDENT and
BCFSYNCH values)
NETWORK
Additional information
-
Range
UNSYNCH (0), BCFSYNCH (1), LMUSYNCH (2),
INDEPENDENT (3), ABISSYNCH (4), NETWORK
(5)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
UNSYNCH ==> 0
BCFSYNCH ==> 1
LMUSYNCH ==> 2
INDEPENDENT ==> 3
ABISSYNCH ==> 4
Default value
UNSYNCH (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
•
BSS21403 Flexi Multiradio TRX HW Activation
BSS21439 - Packet Abis sync. ToP
IEEE1588v2
Interfaces
•
BSC -> RAC
Table 180
DN9813866
Synch Status (Cont.)
Id:0900d8058089b05e
Confidential
285
Base Control Function (BCF) radio network object parameters
References
BSS Radio Network Parameter Dictionary
NSN reference: BSS21403 Flexi Multiradio TRX
HW Activation.
NSN reference: BSS21439 Packet Abis sync. ToP
IEEE1588v2.
MML Commands
EFO, EFL
MML Abbreviated Name
SM
MML Full Name
Synchronization Mode
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 180
8.84
Synch Status (Cont.)
system module HW (SMH)
Parameter name
System Module HW
Abbreviated name
systemModuleHw
Managed object
BCF
Multiplicity
1
Description
Parameter defines used system module HW of the
BTS.
Parameter is only for Flexi Multiradio 10 BTS.
Additional information
-
Range
Not in Use (0), System Module HW is FSxL (1),
System Module HW is FSxG or or FSxF (2)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Not in Use ==> 0
System Module HW is FSxG or or FSxF ==> 2
Default value
Not in Use (0)
Default value notes
-
Required on Creation
Value set by the system
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Table 181
286
System Module HW
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Parameter relationships
-
Related options
-
Related features
•
•
BSS101674 FSxG BTS HW Activation License
BSS101675 FSxL BTS HW Activation License
Interfaces
•
BSC -> RAC
References
-
MML Commands
EFO
MML Abbreviated Name
SMH
MML Full Name
system module HW
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 181
8.85
Base Control Function (BCF) radio network object parameters
System Module HW (Cont.)
text ID (TID)
Parameter name
Text ID
Abbreviated name
inputTextId
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the text ID number
of a text string.
NOTE: The parameter is relevant only for MetroSite, UltraSite, Flexi EDGE and Flexi Multiradio.
NetAct NOTE: Refers to IO Text instance (TID ID).
Additional information
-
Range
1...200
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Special value
removes the text ID (0)
Related functions
-
Table 182
DN9813866
Text ID
Id:0900d8058089b05e
Confidential
287
Base Control Function (BCF) radio network object parameters
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
References
-
MML Commands
EFE, EFP, EFX, EFO
MML Abbreviated Name
TID
MML Full Name
text ID
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 182
8.86
BSS Radio Network Parameter Dictionary
RAC <-> RACApp
RAC <-> BSC
Text ID (Cont.)
text ID of the output 1...6 (OUT1-OUT6)
Parameter name
Text ID Of The Output 1...6
Abbreviated name
textId
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the text ID for the
external output.
NOTE: The parameter is only available for MetroSite, UltraSite, Flexi EDGE, Flexi Multiradio and
Horizon. In the case of MetroSite, the number of
external outputs is 4. In the case of UltraSite, Flexi
EDGE and Flexi Multiradio and Horizon, the
number of external outputs is 6.
NOTE: MML Range: 0: Removes the text from
external output.
Additional information
-
Range
1...200
Step
1
Unit
-
Table 183
288
Text ID Of The Output 1...6
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
•
•
References
-
MML Commands
EFM, EFO
MML Abbreviated Name
OUT1-OUT6
MML Full Name
text ID of the output 1...6
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 183
8.87
RAC <-> RACApp
RAC <-> BSC
Text ID Of The Output 1...6 (Cont.)
TRX shutdown timer (NTIM)
Parameter name
TRX Shutdown Timer
Abbreviated name
normTrxBatbuTimer
Managed object
BCF
Multiplicity
1
Table 184
DN9813866
Base Control Function (BCF) radio network object parameters
TRX Shutdown Timer
Id:0900d8058089b05e
Confidential
289
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the time period after
which shutdown group 1 TRXs are powered down.
The time begins after the TRX Shutdown Timer 2
has expired. Parameter is valid if BTS Battery
Backup Procedure parameter has value "Transmission and BCCH Alive (1)" or "Transmission Alive
(2)".
NOTE: Likewise this parameter is valid only if
Adjustable Intelligent Shutdown for 2G Flexi or
Adjustable Intelligent Shutdown for MetroSite,
UltraSite and Talk-family licence (according to site
type) is ON/CONFIG OR the FIFILE/PRFILE option
for intelligent shutdown is ON, see below for
FIFILE/PRFILE options:
- MetroSite: BTS_METRO_SITE_BATBU_PR
- Talk-family: BTS_SITE_BATBU_PROC_A AND
BTS_SIT_BATBU_PROC
- UltraSite, Flexi EDGE, BTSplus, Flexi Multiradio
and Horizon:
BTS_ULTRA_SITE_BATBU_PR
Additional information
-
Range
0...600
Step
1
Unit
min
Formula for getting
internal value
internal_value = gui_value * 6000
Default value
0 min
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Table 184
290
TRX Shutdown Timer (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Related parameters
batteryBackupProcedure of BCF - Defines the
shutdown procedure to be used (all TRXs shut
down according to shutdown timers, only BCCH
TRX left on or all TRXs left on).
bcchTrxBatbuTimer of BCF - Group 0 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + normTrxBatbuTimer +
bcchTrxBatbuTimer + batteryBackupTimer
batteryBackupTimer of BSC - Defines the time
period for trying to make forced HOs.
normTrxBatbuTimer2 of BCF - Group 2 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + batteryBackupTimer
normTrxBatbuTimer3 of BCF - Group 3 TRXs are
shut down after normTrxBatbuTimer3 + batteryBackupTimer
trxShutdownGroup of TRX - Defines to which
shutdown group the TRX belongs in a mains failure
case.
Parameter relationships
-
Related options
•
Remote Degration Of BTS Service Under TRX
Shutdown (2) (optional) OR BTS Metro Site
Batbu Pr (73) (optional) OR BTS Ultra Site
Batbu Pr (74) (optional) OR Adjustable Intelligent Shutdown, 2G Flexi (101) (optional) OR
Adjustable Intelligent Shutdown for MetroSite,
UltraSite, Talk-family (102) (optional)
Feature dependencies
•
•
BSS20151: Adjustable Intelligent Shutdown
BSS20903: Adjustable Intelligent Shutdown,
2G Flexi
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
•
NSN reference: Gemini Support (BTSplus)
BSS21469 Implementation Specification
NSN reference: BSS21403 - Flexi Multiradio
TRX HW Activation
•
MML Commands
EFC, EFM, EFO
MML Abbreviated Name
NTIM
MML Full Name
TRX shutdown timer
Segment Level Parameter
-
Table 184
DN9813866
TRX Shutdown Timer (Cont.)
Id:0900d8058089b05e
Confidential
291
Base Control Function (BCF) radio network object parameters
File Based Provisioning
supported
Table 184
8.88
BSS Radio Network Parameter Dictionary
true
TRX Shutdown Timer (Cont.)
TRX shutdown timer 2 (NTIM2)
Parameter name
TRX Shutdown Timer 2
Abbreviated name
normTrxBatbuTimer2
Managed object
BCF
Multiplicity
1
Description
With this parameter you define the time period after which
shutdown group 2 TRXs are powered down. The time
begins after the TRX Shutdown Timer 3 has expired.
Parameter is valid only when BTS Battery Backup Procedure parameter has value "Transmission and BCCH
Alive (1)" or "Transmission Alive (2)"
NOTE: Likewise this parameter is valid only if Adjustable
Intelligent Shutdown for FlexiEDGE or Adjustable Intelligent Shutdown for MetroSite, UltraSite and Talk-family
licence (according to site type) is ON/CONFIG.
Additional information
-
Range
0...600
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value * 6000
Default value
0 min
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Table 185
292
TRX Shutdown Timer 2
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Related parameters
batteryBackupProcedure of BCF - Defines the shutdown
procedure to be used (all TRXs shut down according to
shutdown timers, only BCCH TRX left on or all TRXs left
on), bcchTrxBatbuTimer of BCF - Group 0 TRXs are shut
down after normTrxBatbuTimer3 + normTrxBatbuTimer2
+ normTrxBatbuTimer + bcchTrxBatbuTimer + batteryBackupTimer , normTrxBatbuTimer of BCF - Group 1
TRXs are shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + normTrxBatbuTimer + batteryBackupTimer , batteryBackupTimer of BSC - Defines the
time period for trying to make forced HOs,
normTrxBatbuTimer3 of BCF - Group 3 TRXs are shut
down after normTrxBatbuTimer3 + batteryBackupTimer ,
trxShutdownGroup of TRX - Defines to which shutdown
group the TRX belongs in a mains failure case.
Parameter relationships
-
Related options
•
Adjustable Intelligent Shutdown for Flexi EDGE
(101) (optional) OR Adjustable Intelligent Shutdown
for MetroSite, UltraSite, Talk-family (102) (optional)
Related features
•
•
BSS20151: Adjustable Intelligent Shutdown
BSS20903: Separate Licence for Flexi EDGE BTS
Intelligent Shutdown
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EFC,EFM,EFO
MML Abbreviated Name
NTIM2
MML Full Name
TRX shutdown timer 2
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 185
8.89
TRX shutdown timer 3 (NTIM3)
Parameter name
TRX Shutdown Timer 3
Abbreviated name
normTrxBatbuTimer3
Managed object
BCF
Multiplicity
1
Table 186
DN9813866
TRX Shutdown Timer 2 (Cont.)
TRX Shutdown Timer 3
Id:0900d8058089b05e
Confidential
293
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the time period after
which shutdown group 3 TRXs are powered down.
Parameter is valid only when BTS Battery Backup
Procedure parameter has value "Transmission and
BCCH Alive (1)" or "Transmission Alive (2)".
NOTE: Likewise this parameter is valid only if
Adjustable Intelligent Shutdown for FlexiEDGE or
Adjustable Intelligent Shutdown for MetroSite,
UltraSite and Talk-family licence (according to site
type) is ON/CONFIG.
Additional information
-
Range
0...600
Step
1
Unit
min
Formula for getting
internal value
internal_value = gui_value * 6000
Default value
0 min
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
batteryBackupProcedure of BCF - Defines the
shutdown procedure to be used (all TRXs shut
down according to shutdown timers, only BCCH
TRX left on or all TRXs left on).
bcchTrxBatbuTimer of BCF - Group 0 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + normTrxBatbuTimer +
bcchTrxBatbuTimer + batteryBackupTimer
normTrxBatbuTimer of BCF - Group 1 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + normTrxBatbuTimer + batteryBackupTimer
batteryBackupTimer of BSC - Defines the time
period for trying to make forced HOs.
normTrxBatbuTimer2 of BCF - Group 2 TRXs are
shut down after normTrxBatbuTimer3 +
normTrxBatbuTimer2 + batteryBackupTimer
trxShutdownGroup of TRX - Defines to which
shutdown group the TRX belongs in a mains failure
case.
Table 186
294
TRX Shutdown Timer 3 (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Parameter relationships
-
Related options
•
Adjustable Intelligent Shutdown, 2G Flexi (101)
(optional) OR Adjustable Intelligent Shutdown
for MetroSite, UltraSite, Talk-family (102)
(optional)
Feature dependencies
•
•
BSS20151: Adjustable Intelligent Shutdown
BSS20903: Adjustable Intelligent Shutdown,
2G Flexi
Interfaces
•
•
•
•
RACApp <-> RAC
Planner <-> RAC
RAC <-> Optimizer
RAC <-> BSC
References
-
MML Commands
EFC,EFM,EFO
MML Abbreviated Name
NTIM3
MML Full Name
TRX shutdown timer 3
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 186
8.90
TRX Shutdown Timer 3 (Cont.)
UL committed burst size (ULCBS)
Parameter name
UL Committed Burst Size
Abbreviated name
ulCommittedBurstSize
3GPP name
-
Managed Object
BCF
Multiplicity
1
Table 187
DN9813866
Base Control Function (BCF) radio network object parameters
UL Committed Burst Size
Id:0900d8058089b05e
Confidential
295
Base Control Function (BCF) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the Committed
Burst Size to be used when Traffic Shaping has to
be performed in uplink direction.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
NOTE:
This UL Committed Burst Size parameter must be
at least as large as the maximum supported packet
size (platform parameter Maximum Transfer Unit,
MTU)
Additional information
-
Range
0...65535
Step
1
Units
octets
Formula for getting
internal value
internal_value =gui_value
Default value
1500
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150)
Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS101414 Packet Abis Transport Media Conversion
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
NSN reference: BSS21454 Packet Abis over
IP/Eth.
File based provisioning
supported
true
MML Abbreviated Name
ULCBS
MML Commands
EFM, EFO
Table 187
296
UL Committed Burst Size (Cont.)
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
MML Full Name
UL committed burst size
Segment Level Parameter
-
Table 187
8.91
Base Control Function (BCF) radio network object parameters
UL Committed Burst Size (Cont.)
UL committed information rate (ULCIR)
Parameter name
UL Committed Information Rate
Abbreviated name
ulCommittedInformationRate
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
With this parameter you define the Committed
Information Rate for Traffic Shaping in uplink direction.
Value 0 (Not defined) and it is used in BCF creation
as default value to parameter database in BSC.
User cannot give this value.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
DN9813866
Additional information
-
Range
100...250000
Step
100
Units
kbit/s
Formula for getting
internal value
internal_value =gui_value
Default value
-
Default value notes
-
Special value
Not defined (0)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Table 188
UL Committed Information Rate
Id:0900d8058089b05e
Confidential
297
Base Control Function (BCF) radio network object parameters
Related parameters
BSS Radio Network Parameter Dictionary
uplinkTrafficShaping of BCF - This parameter UL
Committed Information Rate (ULCIR) is obligatory,
if parameter Uplink Traffic Shaping value is 1
(Shaping-committed)
abisInterfaceConnectionType of BCF - This parameter UL Committed Information Rate is not used, if
parameter Abis Interface Connection Type value is
1 (Packet Abis over TDM)
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150)
Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS101414 Packet Abis Transport Media Conversion
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
NSN reference: BSS21454 Packet Abis over
IP/Eth.
File based provisioning
supported
true
MML Abbreviated Name
ULCIR
MML Commands
EFM, EFO
MML Full Name
UL committed information rate
Segment Level Parameter
-
Table 188
8.92
uplink traffic shaping (ULTS)
Parameter name
Uplink Traffic Shaping
Abbreviated name
uplinkTrafficShaping
3GPP name
-
Managed Object
BCF
Multiplicity
1
Table 189
298
UL Committed Information Rate (Cont.)
Uplink Traffic Shaping
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Description
With this parameter you define whether Traffic
Shaping functionality is enabled or not for Packet
Abis over Ethernet.
NOTE:
Traffic shaping is supported only for uplink.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
-
Range
No-shaping (0), Shaping-committed (1)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
No-shaping ==> 0
Shaping-committed ==> 1
Default value
No-shaping (0)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
ulCommittedInformationRate of BCF - If this parameter Uplink Traffic Shaping (ULTS) has value 1
(Shaping-committed), then parameter UL Committed Information Rate (ULCIR) is obligatory
abisInterfaceConnectionType of BCF - This parameter Uplink Traffic Shaping is used, if parameter
Abis Interface Connection Type value is 2 (Packet
Abis over Ethernet)
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150)
Packet Abis over TDM (151)
Feature dependencies
BSS21454 Packet Abis over IP/Eth
BSS101414 Packet Abis Transport Media Conversion
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
Table 189
DN9813866
NSN reference: BSS21454 Packet Abis over
IP/Eth.
Uplink Traffic Shaping (Cont.)
Id:0900d8058089b05e
Confidential
299
Base Control Function (BCF) radio network object parameters
File based provisioning
supported
true
MML Abbreviated Name
ULTS
MML Commands
EFM, EFO
MML Full Name
uplink traffic shaping
Segment Level Parameter
-
Table 189
8.93
BSS Radio Network Parameter Dictionary
Uplink Traffic Shaping (Cont.)
Used CS UDP MUX port ()
Parameter name
Used CS UDP MUX port
Abbreviated name
usedCsUdpMuxPort
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter indicates the currently used CS
UDP-MUX Port in ETP and BCF. System updates
the value from the BSC parameter CS UDP MUX
port in BCF unlock and BCF reset.
MML:
The parameter is only shown in outputs.
NOTE:
Parameter is valid only when Packet Abis is used
Additional information
-
Range
49152...65534
Step
2
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
49152
Default value notes
-
Special value
Not defined (65535)
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Table 190
300
Used CS UDP MUX port
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Related parameters
csUdpMuxPort of BSC - System updates the value
from the BSC parameter CS UDP MUX port in BCF
unlock and BCF reset.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) (optional) OR Packet
Abis over TDM (151) (optional)
Feature dependencies
BSS21440 Packet Abis over TDMBSS21454
Packet Abis over IP/Eth
Interfaces
BSC -> RAC
References
-
File based provisioning
supported
false
MML Abbreviated Name
-
MML Commands
EFO
MML Full Name
Used CS UDP MUX port
Segment Level Parameter
-
Table 190
8.94
Base Control Function (BCF) radio network object parameters
Used CS UDP MUX port (Cont.)
Used PS UDP MUX port ()
Parameter name
Used PS UDP MUX port
Abbreviated name
usedPsUdpMuxPort
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
This parameter indicates the currently used PS
UDP-MUX Port in ETP and BCF. System updates
the value from the BSC parameter PS UDP MUX
port in BCF unlock and BCF reset.
MML NOTE:
The parameter is only shown in outputs.
Additional information
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Range
49152...65534
Step
2
Units
-
Table 191
DN9813866
Used PS UDP MUX port
Id:0900d8058089b05e
Confidential
301
Base Control Function (BCF) radio network object parameters
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
internal_value =gui_value
Default value
49154
Default value notes
-
Special value
Not defined (65535)
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
-
Related parameters
psUdpMuxPort of BSC - System updates the value
from the BSC parameter PS UDP MUX port in BCF
unlock and BCF reset.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
BSC -> RAC
References
NSN reference: BSS21454 - Packet Abis over
IP/Eth
File based provisioning
supported
false
MML Abbreviated Name
-
MML Commands
-
MML Full Name
Used PS UDP MUX port
Segment Level Parameter
-
Table 191
8.95
vlan ID (VLANID)
Parameter name
Vlan ID
Abbreviated name
vlanId
3GPP name
-
Managed Object
BCF
Multiplicity
1
Table 192
302
Used PS UDP MUX port (Cont.)
Vlan ID
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Control Function (BCF) radio network object parameters
Description
With this parameter you indicate the VLAN id in
ETP used for the BCF. Parameter is mandatory if
ETP serving the BCF terminates more than one
VLAN.
Additional information
-
Range
1...4095
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
4095
Default value notes
VLAN tagging is not used.
Required on creation
optional
Child parameters
-
Modification
Requires object locking
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150)
Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS101414 Packet Abis Transport Media Conversion
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
NSN reference: BSS21454 Packet Abis over
IP/Eth.
File based provisioning
supported
true
MML Abbreviated Name
VLANID
MML Commands
EFC, EFM, EFO
MML Full Name
vlan ID
Segment Level Parameter
-
Table 192
DN9813866
Vlan ID (Cont.)
Id:0900d8058089b05e
Confidential
303
Base Control Function (BCF) radio network object parameters
8.96
BSS Radio Network Parameter Dictionary
20W power licence usage (PLU)
Parameter name
20W Power Licence Usage
Abbreviated name
powerLicenceUsage
3GPP name
-
Managed Object
BCF
Multiplicity
1
Description
Parameter shows how many 20W power licence
BCF consumes. Value 0 means no licence used,
value 1 means 20W power licence usage, value 2
means 40W power licence usage and so on.
Parameter is valid only for Flexi Multiradio BTS.
Additional information
-
Range
0...255
Step
1
Units
-
Formula for getting
internal value
-
Default value
0
Default value notes
-
Required on creation
Value set by the system
Child parameters
-
Modification
not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
•
•
Interfaces
BSC -> RAC
References
•
•
•
Table 193
304
BSS101688 BSC SUPPORT FOR FLEXI MULTIRADIO 10 BTS
RG301613 BSC SUPPORT FOR FLEXI
COMPACT BTS
BSS21403 Flexi Multiradio TRX HW Activation
BSS101688 BSC SUPPORT FOR FLEXI MULTIRADIO 10 BTS
RG301613 BSC SUPPORT FOR FLEXI
COMPACT BTS
BSS21403 FLEXI MULTIRADIO TRX HW
ACTIVATION
20W Power Licence Usage
Id:0900d8058089b05e
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
File based provisioning
supported
false
MML Abbreviated Name
PLU
MML Commands
EFO
MML Full Name
20W power licence usage
Segment Level Parameter
-
Table 193
DN9813866
Base Control Function (BCF) radio network object parameters
20W Power Licence Usage (Cont.)
Id:0900d8058089b05e
Confidential
305
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
9 Base Station Controller (BSC) radio network
object parameters
9.1
alarm limit for full rate TCH availability (ALFRT)
Parameter name
Alarm Limit For Full Rate TCH Availability
Abbreviated name
frTchALim
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the alarm limit for available full rate traffic channels (%). The parameter is used
by radio network recovery.
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
30 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ. EEO
MML Abbreviated Name
ALFRT
MML Full Name
alarm limit for full rate TCH availability
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 194
306
Alarm Limit For Full Rate TCH Availability
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.2
Base Station Controller (BSC) radio network object parameters
alarm limit for half rate TCH availibility (ALHRT)
Parameter name
Alarm Limit For Half Rate TCH Availibility
Abbreviated name
hrTchALim
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the alarm limit for available half rate traffic channels (%). The parameter is used
by radio network recovery.
Additional information
-
Range
1...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
30 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ. EEO
MML Abbreviated Name
ALHRT
MML Full Name
alarm limit for half rate TCH availibility
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 195
9.3
Alarm Limit For Half Rate TCH Availibility
alarm limit for SDCCH availability (ALSDC)
Parameter name
Table 196
DN9813866
Alarm Limit For SDCCH Availability
Alarm Limit For SDCCH Availability
Id:0900d8058089b05f
Confidential
307
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Abbreviated name
sdcchAlLimit
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the alarm limit for available SDCCHs. The limit is the ratio of working SDCCHs
to working TCHs in percent. The parameter is used by
radio network recovery.
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
30 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
ALSDC
MML Full Name
alarm limit for SDCCH availability
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 196
9.4
Alarm Limit For SDCCH Availability (Cont.)
Alarm Threshold For Number Of Channel Seizure
Requests (CSR)
Parameter name
Table 197
308
Alarm Threshold For Number Of Channel Seizure
Requests
Alarm Threshold For Number Of Channel Seizure Requests
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Abbreviated name
alrmSeizReq
Managed object
BSC
Multiplicity
1
Description
The parameter supervises SDCCH and TCH congestion.
With this parameter you define an alarm threshold for the
number of channel seizures requests. Only when the
number of channel seizure requests equals or exceeds
this threshold during the measurement period, the values
for alarm threshold for TCH congestion and alarm threshold for SDCCH congestion are taken into account.
Additional information
-
Range
1...65535
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
100
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
CSR
MML Full Name
Alarm Threshold For Number Of Channel Seizure
Requests
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 197
DN9813866
Alarm Threshold For Number Of Channel Seizure Requests (Cont.)
Id:0900d8058089b05f
Confidential
309
Base Station Controller (BSC) radio network object parameters
9.5
BSS Radio Network Parameter Dictionary
Alarm Threshold For Number Of Channel Seizures (CS)
Parameter name
Alarm Threshold For Number Of Channel Seizures
Abbreviated name
alrmNoOfSei
Managed object
BSC
Multiplicity
1
Description
The parameter supervises lost calls and too short a mean
holding time in the traffic channels. With this parameter
you define an alarm threshold for the number of channel
seizures. Only when the number of channel seizures
equals or exceeds this threshold during the measurement
period, the alarm threshold values for minimum mean
holding time for TCHs and alarm threshold for TCH failure
rate are taken into account.
Additional information
-
Range
1...65535
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
10
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
CS
MML Full Name
Alarm Threshold For Number Of Channel Seizures
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 198
310
Alarm Threshold For Number Of Channel Seizures
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.6
Base Station Controller (BSC) radio network object parameters
Alarm Threshold For SDCCH Congestion (CNGS)
Parameter name
Alarm Threshold For SDCCH Congestion
Abbreviated name
alrmSdcch
Managed object
BSC
Multiplicity
1
Description
With this parameter you define an alarm threshold for
SDCCH congestion. This parameter supervises the
traffic level of signalling channels in a BTS. If the percentage of SDCCH seizure requests refused due to congestion equals or exceeds the threshold and there have been
enough call attempts during the measurement period (the
number of seizure requests is greater than or equals the
operator-defined threshold value), the alarm system
prints out an alarm.
Additional information
-
Range
1...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
20 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
CNGS
MML Full Name
Alarm Threshold For SDCCH Congestion
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 199
DN9813866
Alarm Threshold For SDCCH Congestion
Id:0900d8058089b05f
Confidential
311
Base Station Controller (BSC) radio network object parameters
9.7
BSS Radio Network Parameter Dictionary
Alarm Threshold For SDCCH Failure Rate (SCHFR)
Parameter name
Alarm Threshold For SDCCH Failure Rate
Abbreviated name
alrmSchFail
Managed object
BSC
Multiplicity
1
Description
With this parameter you define an alarm threshold for the
SDCCH failure rate. If the number of SDCCH failures
equals or exceeds the threshold, the alarm system prints
out an alarm.
Additional information
-
Range
1...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
80 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
SCHFR
MML Full Name
Alarm Threshold For SDCCH Failure Rate
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 200
312
Alarm Threshold For SDCCH Failure Rate
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.8
Alarm Threshold For TCH Congestion (CNGT)
Parameter name
Alarm Threshold For TCH Congestion
Abbreviated name
alrmTch
Managed object
BSC
Multiplicity
1
Description
With this parameter you define an alarm threshold
for traffic channel congestion. The parameter
supervises the traffic level of traffic channels in a
BTS. If the percentage of TCH seizure requests
refused due to congestion equals or exceeds the
threshold and there have been enough call
attempts during the measurement period (the
number of seizure requests is greater than or
equals the operator-defined threshold value), the
alarm system prints out an alarm.
Additional information
-
Range
1...100
Step
1
Unit
%
Formula for getting
internal value
internal_value = gui_value
Default value
20 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
CNGT
MML Full Name
Alarm Threshold For TCH Congestion
Table 201
DN9813866
Base Station Controller (BSC) radio network object parameters
RAC <-> RACApp
RAC <-> BSC
Alarm Threshold For TCH Congestion
Id:0900d8058089b05f
Confidential
313
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 201
9.9
Alarm Threshold For TCH Congestion (Cont.)
Alarm Threshold For TCH Failure Rate (TCHFR)
Parameter name
Alarm Threshold For TCH Failure Rate
Abbreviated name
alrmChFail
Managed object
BSC
Multiplicity
1
Description
With this parameter you define an alarm threshold for
traffic channel failure rate. Whenever a channel is
released with a release cause other than a normal one,
the counter of channel failures for the released channel is
incremented. If the percentage of channel failures equals
or exceeds the threshold and there have been enough
calls during the measurement period (the number of
seizures is greater than or equals the operator-defined
threshold value), the alarm system prints out an alarm.
Additional information
-
Range
1...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
20 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
Table 202
314
BSS Radio Network Parameter Dictionary
Alarm Threshold For TCH Failure Rate
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Abbreviated Name
TCHFR
MML Full Name
Alarm Threshold For TCH Failure Rate
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 202
9.10
Alarm Threshold For TCH Failure Rate (Cont.)
alarm threshold for the share of high TCH interference
(HIFSHR)
Parameter name
Alarm Threshold For The Share Of High TCH Interference
Abbreviated name
maxOnHiIf
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the maximum time in
percent that a TCH may be on high interference levels
during a measurement period (%).
Additional information
-
Range
1...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
50 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
HIFSHR
Table 203
DN9813866
RAC <-> RACApp
RAC <-> BSC
Alarm Threshold For The Share Of High TCH Interference
Id:0900d8058089b05f
Confidential
315
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Full Name
alarm threshold for the share of high TCH interference
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 203
9.11
Alarm Threshold For The Share Of High TCH Interference (Cont.)
AMH lower load threshold (ALT)
Parameter name
AMH Lower Load Threshold
Abbreviated name
amhLowerLoadThreshold
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the lower threshold for the
load of the base station. The parameter is used to trigger
advanced multilayer handling functionality with IUO
and/or Dual Band/ microcell features.
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
20 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
amhLowerLoadThreshold of BTS - If a cell level parameter has some other value than (N/Undefined), it defines
the corresponding BSC-level parameter.
Parameter relationships
-
Related options
Related features
Advanced Multilayer Handling (AMH) (33)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
ALT
Table 204
316
•
AMH Lower Load Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Full Name
AMH lower load threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 204
9.12
AMH Lower Load Threshold (Cont.)
AMH Max Load Of Target Cell (AML)
Parameter name
AMH Max Load Of Target Cell
Abbreviated name
amhMaxLoadOfTgtCell
Managed object
BSC
Multiplicity
1
Description
With this advanced multilayer handling parameter you
define the maximum traffic load in adjacent cell allowed
for a target cell of traffic reason handover (TRHO).
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
70 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
amhMaxLoadOfTgtCell of BTS - If a cell level parameter
has some other value than (N/Undefined), it defines the
corresponding BSC-level parameter.
Parameter relationships
-
Related options
Related features
Advanced Multilayer Handling (AMH) (33)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
AML
MML Full Name
AMH Max Load Of Target Cell
Table 205
DN9813866
•
AMH Max Load Of Target Cell
Id:0900d8058089b05f
Confidential
317
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
BSS Radio Network Parameter Dictionary
-
File Based Provisioning sup- true
ported
Table 205
9.13
AMH Max Load Of Target Cell (Cont.)
AMH upper load threshold (AUT)
Parameter name
AMH Upper Load Threshold
Abbreviated name
amhUpperLoadThreshold
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the upper threshold for the
load of the base station. The parameter is used to trigger
BSC-controlled traffic reason handovers.
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
80 %
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
amhUpperLoadThreshold of BTS - If a cell level parameter has some other value than (N/Undefined), it defines
the corresponding BSC-level parameter.
Parameter relationships
-
Related options
Related features
Advanced Multilayer Handling (AMH) (33)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
AUT
MML Full Name
AMH upper load threshold
Segment Level Parameter
-
Table 206
318
•
AMH Upper Load Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 206
9.14
AMH Upper Load Threshold (Cont.)
AMR Configuration In Handovers (ACH)
Parameter name
AMR Configuration In Handovers
Abbreviated name
amrConfInHandovers
Managed object
BSC
Multiplicity
1
Description
The attribute defines the preference between the currently used multirate configuration and the one defined
for the target BTS during internal handovers.
MML Range:
1 = the currently used multirate configuration is preferred
in further channel allocations
2 = the multirate configuration of target BTS is preferred
in further channel allocations
Additional information
-
Range
Currently used multirate (1), Multirate configuration of
target BTS (2)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Currently used multirate ==> 1
Multirate configuration of target BTS ==> 2
Default value
Currently used multirate (1)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
AMR FR (50) (optional) OR AMR HR (72) (optional)
Related features
•
BSS20249: AMR FR Licence Control
Interfaces
•
•
RACApp <-> RAC
BSC <-> RAC
References
-
MML Commands
EEM, EEO
Table 207
DN9813866
AMR Configuration In Handovers
Id:0900d8058089b05f
Confidential
319
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Abbreviated Name
ACH
MML Full Name
AMR Configuration In Handovers
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 207
9.15
AMR Configuration In Handovers (Cont.)
AMR lower limit for FR resources (AHRL)
Parameter name
AMR Lower Limit For FR Resources
Abbreviated name
amrLoadDepTchRateLower
Managed object
BSC
Multiplicity
1
Description
The parameter controls the TCH channel rate
determination for AMR calls in the cells of the BSC
according to the cell load of each particular cell.
With this parameter you define the lower limit for the
percentage of free full rate resources. AMR full rate
TCHs are allocated until the number of free full rate
resources is reduced below the value of the parameter. AMR half rate resources are then allocated.
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting
internal value
internal_value = gui_value
Default value
40 %
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Table 208
320
AMR Lower Limit For FR Resources
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related parameters
amrLoadDepTchRateUpper of BSC - AMR Lower
Limit For FR Resources is applied together with
AMR upper limit for FR resources in an individual
SEG if no SEG-specific channel rate control rules
have been specified with the parameters AMR
lower limit for SEG FR resources and AMR upper
limit for SEG FR resources. If this parameter´s
value is higher than the value of the AMR upper
limit for FR resources, then the effect of these two
BSC level channel rate control parameters is deactivated.
amrSegLoadDepTchRateLower of BTS - AMR
Lower Limit For FR Resources is applied together
with AMR upper limit for FR resources in an individual SEG if no SEG-specific channel rate control
rules have been specified with the parameters AMR
lower limit for SEG FR resources and AMR upper
limit for SEG FR resources.
amrSegLoadDepTchRateUpper of BTS - AMR
Lower Limit For FR Resources is applied together
with AMR upper limit for FR resources in an individual SEG if no SEG-specific channel rate control
rules have been specified with the parameters AMR
lower limit for SEG FR resources and AMR upper
limit for SEG FR resources.
Parameter relationships
-
Related options
•
Load based AMR packing (111) (optional) AND
AMR HR (72) (optional)
Feature dependencies
•
BSS21154: Load based AMR packing
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
AHRL
MML Full Name
AMR lower limit for FR resources
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 208
DN9813866
AMR Lower Limit For FR Resources (Cont.)
Id:0900d8058089b05f
Confidential
321
Base Station Controller (BSC) radio network object parameters
9.16
BSS Radio Network Parameter Dictionary
AMR PPC DL FR Lower Threshold 1 (LDF1)
Parameter name
AMR PPC DL FR Lower Threshold 1
Abbreviated name
amrPpcDlFrLowerThreshold1
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold dl Rx qual AMR FR (LDRF) - 2 is used, and the
lower border for a range where pc lower threshold dl Rx
qual AMR FR (LDRF) - 1 is used to trigger a power
increase due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC DL FR Lower Threshold 1").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC DL FR Lower Threshold 1").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
30 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcLThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default FR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
Table 209
322
AMR PPC DL FR Lower Threshold 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LDF1
MML Full Name
AMR PPC DL FR Lower Threshold 1
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 209
9.17
AMR PPC DL FR Lower Threshold 1 (Cont.)
AMR PPC DL FR Lower Threshold 2 (LDF2)
Parameter name
AMR PPC DL FR Lower Threshold 2
Abbreviated name
amrPpcDlFrLowerThreshold2
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL
power ranges for the AMR Progressive Power
Control algorithm. This is the upper border for a
range where pc lower threshold dl Rx qual AMR FR
(LDRF) - 1 is used, and the lower border for a range
where pc lower threshold dl Rx qual AMR FR
(LDRF) is used to trigger a power increase due to
DL quality.
When this threshold defines the upper border for
the range, the threshold value is not part of the
range (that is, when power < "AMR PPC DL FR
Lower Threshold 2"). When this threshold defines
the lower border for the range, the threshold value
is part of the range (that is, when power >= "AMR
PPC DL FR Lower Threshold 2")
The value of this parameter is attenuation from the
peak power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
18 dB
Default value notes
MML default
Table 210
DN9813866
AMR PPC DL FR Lower Threshold 2
Id:0900d8058089b05f
Confidential
323
Base Station Controller (BSC) radio network object parameters
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcLThrDlRxQual of BTS - With this
parameter you define the threshold level of the
downlink signal quality measurements for the BTS
power increase. Defined for the default FR AMR
set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm
(106) (optional) AND AMR FR (50) (optional)
Feature dependencies
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LDF2
MML Full Name
AMR PPC DL FR Lower Threshold 2
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 210
9.18
AMR PPC DL FR Lower Threshold 2 (Cont.)
AMR PPC DL FR Lower Threshold 3 (LDF3)
Parameter name
AMR PPC DL FR Lower Threshold 3
Abbreviated name
amrPpcDlFrLowerThreshold3
Managed object
BSC
Multiplicity
1
Table 211
324
BSS Radio Network Parameter Dictionary
AMR PPC DL FR Lower Threshold 3
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold dl Rx qual AMR FR (LDRF) is used, and the
lower border for a range where pc lower threshold dl Rx
qual AMR FR (LDRF) + 1 is used to trigger a power
increase due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC DL FR Lower Threshold 3").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC DL FR Lower Threshold 3")
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
6 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcLThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default FR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LDF3
MML Full Name
AMR PPC DL FR Lower Threshold 3
Segment Level Parameter
-
Table 211
DN9813866
AMR PPC DL FR Lower Threshold 3 (Cont.)
Id:0900d8058089b05f
Confidential
325
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 211
9.19
AMR PPC DL FR Lower Threshold 3 (Cont.)
AMR PPC DL FR Lower Threshold 4 (LDF4)
Parameter name
AMR PPC DL FR Lower Threshold 4
Abbreviated name
amrPpcDlFrLowerThreshold4
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold dl Rx qual AMR FR (LDRF) + 1 is used, and the
lower border for a range where pc lower threshold dl Rx
qual AMR FR (LDRF) + 2 is used to trigger a power
increase due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC DL FR Lower Threshold 4").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC DL FR Lower Threshold 4")
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
0 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcLThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default FR AMR set.
Parameter relationships
-
Table 212
326
AMR PPC DL FR Lower Threshold 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LDF4
MML Full Name
AMR PPC DL FR Lower Threshold 4
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 212
9.20
AMR PPC DL FR Lower Threshold 4 (Cont.)
AMR HR unpacking control (AHRUC)
Parameter name
AMR HR Unpacking Control
Abbreviated name
amrHrUnpackingControl
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you allow, limit or totally
prevent AMR HR to AMR FR unpacking for AMR
HR calls made by low priority users in the feature
Half Rate for Low Priority Subscribers.
Additional information
-
Range
unpacking prevented (0),
unpacking partly allowed (1),
unpacking allowed (2)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
unpacking prevented ==> 0
unpacking partly allowed ==> 1
unpacking allowed ==> 2
Default value
unpacking prevented (0)
Default value notes
-
Table 213
DN9813866
AMR HR Unpacking Control
Id:0900d8058089b05f
Confidential
327
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Required on creation
Value set by the system
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
btsLoadDepTchRateLower of BSC - When
BSS21154 Load based AMR packing is NOT in use
the load limit for AMR HR packing is defined by
parameters Lower Limit For FR TCH Resources of
BSC, Upper Limit For FR TCH Resources of BSC,
Lower Limit For FR TCH Resources of BTS and
Upper Limit For FR TCH Resources of BTS.
btsLoadDepTchRateUpper of BSC - When
BSS21154 Load based AMR packing is NOT in use
the load limit for AMR HR packing is defined by
parameters Lower Limit For FR TCH Resources of
BSC, Upper Limit For FR TCH Resources of BSC,
Lower Limit For FR TCH Resources of BTS and
Upper Limit For FR TCH Resources of BTS.
btsSpLoadDepTchRateLower of BTS - When
BSS21154 Load based AMR packing is NOT in use
the load limit for AMR HR packing is defined by
parameters Lower Limit For FR TCH Resources of
BSC, Upper Limit For FR TCH Resources of BSC,
Lower Limit For FR TCH Resources of BTS and
Upper Limit For FR TCH Resources of BTS.
btsSpLoadDepTchRateUpper of BTS - When
BSS21154 Load based AMR packing is NOT in use
the load limit for AMR HR packing is defined by
parameters Lower Limit For FR TCH Resources of
BSC, Upper Limit For FR TCH Resources of BSC,
Lower Limit For FR TCH Resources of BTS and
Upper Limit For FR TCH Resources of BTS.
amrLoadDepTchRateLower of BSC - When
BSS21154 Load based AMR packing is in use the
load limit for AMR HR packing is defined by parameters AMR Lower Limit For FR Resources of BSC,
AMR Upper Limit For FR Resources of BSC, AMR
Lower Limit For SEG FR Resources of BTS and
AMR Upper Limit For SEG FR Resources of BTS.
Table 213
328
AMR HR Unpacking Control (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related parameters
amrLoadDepTchRateUpper of BSC - When
BSS21154 Load based AMR packing is in use the
load limit for AMR HR packing is defined by parameters AMR Lower Limit For FR Resources of BSC,
AMR Upper Limit For FR Resources of BSC, AMR
Lower Limit For SEG FR Resources of BTS and
AMR Upper Limit For SEG FR Resources of BTS.
amrSegLoadDepTchRateLower of BTS - When
BSS21154 Load based AMR packing is in use the
load limit for AMR HR packing is defined by parameters AMR Lower Limit For FR Resources of BSC,
AMR Upper Limit For FR Resources of BSC, AMR
Lower Limit For SEG FR Resources of BTS and
AMR Upper Limit For SEG FR Resources of BTS.
amrSegLoadDepTchRateUpper of BTS - When
BSS21154 Load based AMR packing is in use the
load limit for AMR HR packing is defined by parameters AMR Lower Limit For FR Resources of BSC,
AMR Upper Limit For FR Resources of BSC, AMR
Lower Limit For SEG FR Resources of BTS and
AMR Upper Limit For SEG FR Resources of BTS.
Parameter relationships
Operation with the parameter’s value 1 depends on
the values of the parameters that define the load
limit for AMR HR packing for normal users.
Related options
Priority based Voice Quality (159) (optional) AND
AMR FR (50) (optional) AND AMR HR (72)
(optional)
Feature dependencies
BSS101456: Priority based Voice Quality
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
-
File based provisioning
supported
true
MML Abbreviated Name
AHRUC
MML Commands
EEQ
MML Full Name
AMR HR unpacking control
Segment Level Parameter
-
Table 213
DN9813866
AMR HR Unpacking Control (Cont.)
Id:0900d8058089b05f
Confidential
329
Base Station Controller (BSC) radio network object parameters
9.21
BSS Radio Network Parameter Dictionary
AMR PPC DL FR Upper Threshold 1 (UDF1)
Parameter name
AMR PPC DL FR Upper Threshold 1
Abbreviated name
amrPpcDlFrUpperThreshold1
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold dl Rx qual AMR FR (UDRF) - 2 is used, and the
lower border for a range where pc upper threshold dl Rx
qual AMR FR (UDRF) - 1 is used to trigger a power
decrease due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC DL FR Upper Threshold 1").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC DL FR Upper Threshold 1").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
30 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcUThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power decrease.
Defined for the default FR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
Table 214
330
AMR PPC DL FR Upper Threshold 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UDF1
MML Full Name
AMR PPC DL FR Upper Threshold 1
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 214
9.22
AMR PPC DL FR Upper Threshold 1 (Cont.)
AMR PPC DL FR Upper Threshold 2 (UDF2)
Parameter name
AMR PPC DL FR Upper Threshold 2
Abbreviated name
amrPpcDlFrUpperThreshold2
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL
power ranges for the AMR Progressive Power
Control algorithm. This is the upper border for a
range where pc upper threshold dl Rx qual AMR FR
(UDRF) - 1 is used and the lower border for a range
where pc upper threshold dl Rx qual AMR FR
(UDRF) is used to trigger a power decrease due to
DL quality.
When this threshold defines the upper border for
the range, the threshold value is not part of the
range (that is when power < "AMR PPC DL FR
Upper Threshold 2"). When this threshold defines
the lower border for the range, the threshold value
is part of the range (that is when power >= "AMR
PPC DL FR Upper Threshold 2").
The value of this parameter is attenuation from the
peak power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
18 dB
Default value notes
MML default
Table 215
DN9813866
AMR PPC DL FR Upper Threshold 2
Id:0900d8058089b05f
Confidential
331
Base Station Controller (BSC) radio network object parameters
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcUThrDlRxQual of BTS - With this
parameter you define the threshold level of the
downlink signal quality measurements for the BTS
power decrease. Defined for the default FR AMR
set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm
(106) (optional) AND AMR FR (50) (optional)
Feature dependencies
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UDF2
MML Full Name
AMR PPC DL FR Upper Threshold 2
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 215
9.23
AMR PPC DL FR Upper Threshold 2 (Cont.)
AMR PPC DL FR Upper Threshold 3 (UDF3)
Parameter name
AMR PPC DL FR Upper Threshold 3
Abbreviated name
amrPpcDlFrUpperThreshold3
Managed object
BSC
Multiplicity
1
Table 216
332
BSS Radio Network Parameter Dictionary
AMR PPC DL FR Upper Threshold 3
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold dl Rx qual AMR FR (UDRF) is used and the
lower border for a range where pc upper threshold dl Rx
qual AMR FR (UDRF) + 1 is used to trigger a power
decrease due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is
when power < "AMR PPC DL FR Upper Threshold 3").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is
when power >= "AMR PPC DL FR Upper Threshold 3").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
6 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcUThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power decrease.
Defined for the default FR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UDF3
MML Full Name
AMR PPC DL FR Upper Threshold 3
Segment Level Parameter
-
Table 216
DN9813866
AMR PPC DL FR Upper Threshold 3 (Cont.)
Id:0900d8058089b05f
Confidential
333
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 216
9.24
AMR PPC DL FR Upper Threshold 3 (Cont.)
AMR PPC DL FR Upper Threshold 4 (UDF4)
Parameter name
AMR PPC DL FR Upper Threshold 4
Abbreviated name
amrPpcDlFrUpperThreshold4
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold dl Rx qual AMR FR (UDRF) + 1 is used and the
lower border for a range where pc upper threshold dl Rx
qual AMR FR (UDRF) + 2 is used to trigger a power
decrease due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is
when power < "AMR PPC DL FR Upper Threshold 4").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is
when power >= "AMR PPC DL FR Upper Threshold 4").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
0 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcUThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power decrease.
Defined for the default FR AMR set.
Parameter relationships
-
Table 217
334
AMR PPC DL FR Upper Threshold 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UDF4
MML Full Name
AMR PPC DL FR Upper Threshold 4
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 217
9.25
AMR PPC DL FR Upper Threshold 4 (Cont.)
AMR PPC DL HR Lower Threshold 1 (LDH1)
Parameter name
AMR PPC DL HR Lower Threshold 1
Abbreviated name
amrPpcDlHrLowerThreshold1
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold dl Rx qual AMR HR (LDRH) - 2 is used and the
lower border for a range where pc lower threshold dl Rx
qual AMR HR (LDRH) - 1 is used to trigger a power
increase due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < " AMR PPC DL HR Lower Threshold 1").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= " AMR PPC DL HR Lower Threshold 1").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
30 dB
Table 218
DN9813866
AMR PPC DL HR Lower Threshold 1
Id:0900d8058089b05f
Confidential
335
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcLThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LDH1
MML Full Name
AMR PPC DL HR Lower Threshold 1
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 218
9.26
AMR PPC DL HR Lower Threshold 2 (LDH2)
Parameter name
AMR PPC DL HR Lower Threshold 2
Abbreviated name
amrPpcDlHrLowerThreshold2
Managed object
BSC
Multiplicity
1
Table 219
336
AMR PPC DL HR Lower Threshold 1 (Cont.)
AMR PPC DL HR Lower Threshold 2
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold dl Rx qual AMR HR (LDRH) - 1 is used and the
lower border for a range where pc lower threshold dl Rx
qual AMR HR (LDRH) is used to trigger a power increase
due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < " AMR PPC DL HR Lower Threshold 2").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= " AMR PPC DL HR Lower Threshold 2").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
18 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcLThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LDH2
MML Full Name
AMR PPC DL HR Lower Threshold 2
Segment Level Parameter
-
Table 219
DN9813866
AMR PPC DL HR Lower Threshold 2 (Cont.)
Id:0900d8058089b05f
Confidential
337
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 219
9.27
AMR PPC DL HR Lower Threshold 2 (Cont.)
AMR PPC DL HR Lower Threshold 3 (LDH3)
Parameter name
AMR PPC DL HR Lower Threshold 3
Abbreviated name
amrPpcDlHrLowerThreshold3
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold dl Rx qual AMR HR (LDRH) is used and the
lower border for a range where pc lower threshold dl Rx
qual AMR HR (LDRH) + 1 is used to trigger a power
increase due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < " AMR PPC DL HR Lower Threshold 3").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= " AMR PPC DL HR Lower Threshold 3").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
6 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcLThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default HR AMR set.
Parameter relationships
-
Table 220
338
AMR PPC DL HR Lower Threshold 3
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LDH3
MML Full Name
AMR PPC DL HR Lower Threshold 3
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 220
9.28
AMR PPC DL HR Lower Threshold 3 (Cont.)
AMR PPC DL HR Lower Threshold 4 (LDH4)
Parameter name
AMR PPC DL HR Lower Threshold 4
Abbreviated name
amrPpcDlHrLowerThreshold4
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold dl Rx qual AMR HR (LDRH) + 1 is used and the
lower border for a range where pc lower threshold dl Rx
qual AMR HR (LDRH) + 2 is used to trigger a power
increase due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < " AMR PPC DL HR Lower Threshold 4").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= " AMR PPC DL HR Lower Threshold 4").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
0 dB
Table 221
DN9813866
AMR PPC DL HR Lower Threshold 4
Id:0900d8058089b05f
Confidential
339
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcLThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LDH4
MML Full Name
AMR PPC DL HR Lower Threshold 4
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 221
9.29
AMR PPC DL HR Upper Threshold 1 (UDH1)
Parameter name
AMR PPC DL HR Upper Threshold 1
Abbreviated name
amrPpcDlHrUpperThreshold1
Managed object
BSC
Multiplicity
1
Table 222
340
AMR PPC DL HR Lower Threshold 4 (Cont.)
AMR PPC DL HR Upper Threshold 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold dl Rx qual AMR HR (UDRH) - 2 is used and the
lower border for a range where pc upper threshold dl Rx
qual AMR FR (UDRH) - 1 is used to trigger a power
decrease due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < " AMR PPC DL HR Upper Threshold 1").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= " AMR PPC DL HR Upper Threshold 1").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
30 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcUThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power decrease.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UDH1
MML Full Name
AMR PPC DL HR Upper Threshold 1
Segment Level Parameter
-
Table 222
DN9813866
AMR PPC DL HR Upper Threshold 1 (Cont.)
Id:0900d8058089b05f
Confidential
341
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 222
9.30
AMR PPC DL HR Upper Threshold 1 (Cont.)
AMR PPC DL HR Upper Threshold 2 (UDH2)
Parameter name
AMR PPC DL HR Upper Threshold 2
Abbreviated name
amrPpcDlHrUpperThreshold2
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold dl Rx qual AMR HR (UDRH) - 1 is used and the
lower border for a range where pc upper threshold dl Rx
qual AMR FR (UDRH) is used to trigger a power
decrease due to DL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < " AMR PPC DL HR Upper Threshold 2").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= " AMR PPC DL HR Upper Threshold 2").
The value of this parameter is attenuation from the peak
power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
18 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcUThrDlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power decrease.
Defined for the default HR AMR set.
Parameter relationships
-
Table 223
342
AMR PPC DL HR Upper Threshold 2
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UDH2
MML Full Name
AMR PPC DL HR Upper Threshold 2
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 223
9.31
AMR PPC DL HR Upper Threshold 2 (Cont.)
AMR PPC DL HR Upper Threshold 3 (UDH3)
Parameter name
AMR PPC DL HR Upper Threshold 3
Abbreviated name
amrPpcDlHrUpperThreshold3
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of DL
power ranges for the AMR Progressive Power
Control algorithm. This is the upper border for a
range where pc upper threshold dl Rx qual AMR HR
(UDRH) is used and the lower border for a range
where pc upper threshold dl Rx qual AMR FR
(UDRH) + 1 is used to trigger a power decrease due
to DL quality.
When this threshold defines the upper border for
the range, the threshold value is not part of the
range (that is, when power < " AMR PPC DL HR
Upper Threshold 3"). When this threshold defines
the lower border for the range, the threshold value
is part of the range (that is, when power >= " AMR
PPC DL HR Upper Threshold 3").
The value of this parameter is attenuation from the
peak power of the TRX.
Additional information
-
Range
0...30
Step
2
Table 224
DN9813866
AMR PPC DL HR Upper Threshold 3
Id:0900d8058089b05f
Confidential
343
Base Station Controller (BSC) radio network object parameters
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
6 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcUThrDlRxQual of BTS - With this
parameter you define the threshold level of the
downlink signal quality measurements for the BTS
power decrease. Defined for the default HR AMR
set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm
(106) (optional) AND AMR HR (72) (optional)
Feature dependencies
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UDH3
MML Full Name
AMR PPC DL HR Upper Threshold 3
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 224
9.32
AMR PPC DL HR Upper Threshold 3 (Cont.)
AMR PPC DL HR Upper Threshold 4 (UDH4)
Parameter name
AMR PPC DL HR Upper Threshold 4
Abbreviated name
amrPpcDlHrUpperThreshold4
Managed object
BSC
Multiplicity
1
Table 225
344
BSS Radio Network Parameter Dictionary
AMR PPC DL HR Upper Threshold 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
With this parameter you define the border of DL
power ranges for the AMR Progressive Power
Control algorithm. This is the upper border for a
range where pc upper threshold dl Rx qual AMR HR
(UDRH) +1 is used and the lower border for a
range where pc upper threshold dl Rx qual AMR FR
(UDRH) + 2 is used to trigger a power decrease due
to DL quality.
When this threshold defines the upper border for
the range, the threshold value is not part of the
range (that is when power < "AMR PPC DL HR
Upper Threshold 4"). When this threshold defines
the lower border for the range, the threshold value
is part of the range (that is when power >= "AMR
PPC DL HR Upper Threshold 4").
The value of this parameter is attenuation from the
peak power of the TRX.
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
0 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcUThrDlRxQual of BTS - With this
parameter you define the threshold level of the
downlink signal quality measurements for the BTS
power decrease. Defined for the default HR AMR
set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm
(106) (optional) AND AMR HR (72) (optional)
Feature dependencies
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
Table 225
DN9813866
AMR PPC DL HR Upper Threshold 4 (Cont.)
Id:0900d8058089b05f
Confidential
345
Base Station Controller (BSC) radio network object parameters
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UDH4
MML Full Name
AMR PPC DL HR Upper Threshold 4
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 225
9.33
BSS Radio Network Parameter Dictionary
AMR PPC DL HR Upper Threshold 4 (Cont.)
AMR PPC UL FR Lower Threshold 1 (LUF1)
Parameter name
AMR PPC UL FR Lower Threshold 1
Abbreviated name
amrPpcUlFrLowerThreshold1
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL
power ranges for the AMR Progressive Power
Control algorithm. This is the upper border for a
range where pc lower threshold ul Rx qual AMR FR
(LURF) - 2 is used and the lower border for a range
where pc lower threshold ul Rx qual AMR FR
(LURF) - 1 is used to trigger a power increase due
to UL quality.
When this threshold defines the upper border for
the range, the threshold value is not part of the
range (that is, when power < " AMR PPC UL FR
Lower Threshold 1"). When this threshold defines
the lower border for the range, the threshold value
is part of the range (that is, when power >= " AMR
PPC UL FR Lower Threshold 1").
The value of this parameter is attenuation from the
peak power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
30 dB
Table 226
346
AMR PPC UL FR Lower Threshold 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcLThrUlRxQual of BTS - With this
parameter you define the threshold level of the
downlink signal quality measurements for the MS
power increase. Defined for the default FR AMR
set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm
(106) (optional) AND AMR FR (50) (optional)
Feature dependencies
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LUF1
MML Full Name
AMR PPC UL FR Lower Threshold 1
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 226
9.34
AMR PPC UL FR Lower Threshold 1 (Cont.)
AMR PPC UL FR Lower Threshold 2 (LUF2)
Parameter name
AMR PPC UL FR Lower Threshold 2
Abbreviated name
amrPpcUlFrLowerThreshold2
Managed object
BSC
Multiplicity
1
Table 227
DN9813866
Base Station Controller (BSC) radio network object parameters
AMR PPC UL FR Lower Threshold 2
Id:0900d8058089b05f
Confidential
347
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold ul Rx qual AMR FR (LURF) - 1 is used and the
lower border for a range where pc lower threshold ul Rx
qual AMR FR (LURF) is used to trigger a power increase
due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL FR Lower Threshold 2").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL FR Lower Threshold 2").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
18 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcLThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power increase.
Defined for the default FR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LUF2
MML Full Name
AMR PPC UL FR Lower Threshold 2
Segment Level Parameter
-
Table 227
348
AMR PPC UL FR Lower Threshold 2 (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 227
9.35
AMR PPC UL FR Lower Threshold 2 (Cont.)
AMR PPC UL FR Lower Threshold 3 (LUF3)
Parameter name
AMR PPC UL FR Lower Threshold 3
Abbreviated name
amrPpcUlFrLowerThreshold3
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold ul Rx qual AMR FR (LURF) is used and the
lower border for a range where pc lower threshold ul Rx
qual AMR FR (LURF) + 1 is used to trigger a power
increase due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL FR Lower Threshold 3").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL FR Lower Threshold 3").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
6 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcLThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power increase.
Defined for the default FR AMR set.
Parameter relationships
-
Table 228
DN9813866
AMR PPC UL FR Lower Threshold 3
Id:0900d8058089b05f
Confidential
349
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LUF3
MML Full Name
AMR PPC UL FR Lower Threshold 3
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 228
9.36
AMR PPC UL FR Lower Threshold 3 (Cont.)
AMR PPC UL FR Lower Threshold 4 (LUF4)
Parameter name
AMR PPC UL FR Lower Threshold 4
Abbreviated name
amrPpcUlFrLowerThreshold4
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL
power ranges for the AMR Progressive Power
Control algorithm. This is the upper border for a
range where pc lower threshold ul Rx qual AMR FR
(LURF) + 1 is used and the lower border for a range
where pc lower threshold ul Rx qual AMR FR
(LURF) + 2 is used to trigger a power increase due
to UL quality.
When this threshold defines the upper border for
the range, the threshold value is not part of the
range (that is, when power < " AMR PPC UL FR
Lower Threshold 4"). When this threshold defines
the lower border for the range, the threshold value
is part of the range (that is, when power >= " AMR
PPC UL FR Lower Threshold 4").
The value of this parameter is attenuation from the
peak power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Table 229
350
AMR PPC UL FR Lower Threshold 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
0 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcLThrUlRxQual of BTS - With this
parameter you define the threshold level of the
downlink signal quality measurements for the MS
power increase. Defined for the default FR AMR
set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm
(106) (optional) AND AMR FR (50) (optional)
Feature dependencies
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LUF4
MML Full Name
AMR PPC UL FR Lower Threshold 4
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 229
9.37
AMR PPC UL FR Lower Threshold 4 (Cont.)
AMR PPC UL FR Upper Threshold 1 (UUF1)
Parameter name
AMR PPC UL FR Upper Threshold 1
Abbreviated name
amrPpcUlFrUpperThreshold1
Managed object
BSC
Multiplicity
1
Table 230
DN9813866
Base Station Controller (BSC) radio network object parameters
AMR PPC UL FR Upper Threshold 1
Id:0900d8058089b05f
Confidential
351
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold ul Rx qual AMR FR (UURF) - 2 is used and the
lower border for a range where pc upper threshold ul Rx
qual AMR FR (UURF) - 1 is used to trigger a power
decrease due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < " AMR PPC UL FR Upper Threshold 1").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= " AMR PPC UL FR Upper Threshold 1").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
30 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcUThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power decrease.
Defined for the default FR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UUF1
MML Full Name
AMR PPC UL FR Upper Threshold 1
Segment Level Parameter
-
Table 230
352
AMR PPC UL FR Upper Threshold 1 (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 230
9.38
AMR PPC UL FR Upper Threshold 1 (Cont.)
AMR PPC UL FR Upper Threshold 2 (UUF2)
Parameter name
AMR PPC UL FR Upper Threshold 2
Abbreviated name
amrPpcUlFrUpperThreshold2
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold ul Rx qual AMR FR (UURF) - 1 is used and the
lower border for a range where pc upper threshold ul Rx
qual AMR FR (UURF) is used to trigger a power decrease
due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL FR Upper Threshold 2").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL FR Upper Threshold 2").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
18 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcUThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power decrease.
Defined for the default FR AMR set.
Parameter relationships
-
Table 231
DN9813866
AMR PPC UL FR Upper Threshold 2
Id:0900d8058089b05f
Confidential
353
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UUF2
MML Full Name
AMR PPC UL FR Upper Threshold 2
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 231
9.39
AMR PPC UL FR Upper Threshold 2 (Cont.)
AMR PPC UL FR Upper Threshold 3 (UUF3)
Parameter name
AMR PPC UL FR Upper Threshold 3
Abbreviated name
amrPpcUlFrUpperThreshold3
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold ul Rx qual AMR FR (UURF) is used and the
lower border for a range where pc upper threshold ul Rx
qual AMR FR (UURF) + 1 is used to trigger a power
decrease due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL FR Upper Threshold 3").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL FR Upper Threshold 3").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
6 dB
Table 232
354
AMR PPC UL FR Upper Threshold 3
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcUThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power decrease.
Defined for the default FR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR FR (50) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UUF3
MML Full Name
AMR PPC UL FR Upper Threshold 3
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 232
9.40
AMR PPC UL FR Upper Threshold 4 (UUF4)
Parameter name
AMR PPC UL FR Upper Threshold 4
Abbreviated name
amrPpcUlFrUpperThreshold4
Managed object
BSC
Multiplicity
1
Table 233
DN9813866
AMR PPC UL FR Upper Threshold 3 (Cont.)
AMR PPC UL FR Upper Threshold 4
Id:0900d8058089b05f
Confidential
355
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the border of UL
power ranges for the AMR Progressive Power
Control algorithm. This is the upper border for a
range where pc upper threshold ul Rx qual AMR FR
(UURF) + 1 is used and the lower border for a range
where pc upper threshold ul Rx qual AMR FR
(UURF) + 2 is used to trigger a power decrease due
to UL quality.
When this threshold defines the upper border for
the range, the threshold value is not part of the
range (that is, when power < "AMR PPC UL FR
Upper Threshold 4"). When this threshold defines
the lower border for the range, the threshold value
is part of the range (that is, when power >= " AMR
PPC UL FR Upper Threshold 4").
The value of this parameter is attenuation from the
peak power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting
internal value
internal_value = gui_value / 2
Default value
0 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocFrPcUThrUlRxQual of BTS - With this
parameter you define the threshold level of the
downlink signal quality measurements for the MS
power decrease. Defined for the default FR AMR
set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm
(106) (optional) AND AMR FR (50) (optional)
Feature dependencies
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
Table 233
356
AMR PPC UL FR Upper Threshold 4 (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UUF4
MML Full Name
AMR PPC UL FR Upper Threshold 4
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 233
9.41
Base Station Controller (BSC) radio network object parameters
AMR PPC UL FR Upper Threshold 4 (Cont.)
AMR PPC UL HR Lower Threshold 1 (LUH1)
Parameter name
AMR PPC UL HR Lower Threshold 1
Abbreviated name
amrPpcUlHrLowerThreshold1
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold ul Rx qual AMR HR (LURH) - 2 is used and the
lower border for a range where pc lower threshold ul Rx
qual AMR HR (LURH) - 1 is used to trigger a power
increase due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL HR Lower Threshold 1").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL HR Lower Threshold 1").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
30 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
255
Related functions
Power Control
Table 234
DN9813866
AMR PPC UL HR Lower Threshold 1
Id:0900d8058089b05f
Confidential
357
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcLThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power decrease.
Defined for the default FR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LUH1
MML Full Name
AMR PPC UL HR Lower Threshold 1
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 234
9.42
AMR PPC UL HR Lower Threshold 1 (Cont.)
AMR PPC UL HR Lower Threshold 2 (LUH2)
Parameter name
AMR PPC UL HR Lower Threshold 2
Abbreviated name
amrPpcUlHrLowerThreshold2
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold ul Rx qual AMR HR (LURH) - 1 is used and the
lower border for a range where pc lower threshold ul Rx
qual AMR HR (LURH) is used to trigger a power increase
due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL HR Lower Threshold 2").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL HR Lower Threshold 2").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
Table 235
358
-
AMR PPC UL HR Lower Threshold 2
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
18 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcLThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LUH2
MML Full Name
AMR PPC UL HR Lower Threshold 2
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 235
9.43
AMR PPC UL HR Lower Threshold 3 (LUH3)
Parameter name
AMR PPC UL HR Lower Threshold 3
Abbreviated name
amrPpcUlHrLowerThreshold3
Managed object
BSC
Multiplicity
1
Table 236
DN9813866
AMR PPC UL HR Lower Threshold 2 (Cont.)
AMR PPC UL HR Lower Threshold 3
Id:0900d8058089b05f
Confidential
359
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold ul Rx qual AMR HR (LURH) is used and the
lower border for a range where pc lower threshold ul Rx
qual AMR HR (LURH) + 1 is used to trigger a power
increase due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL HR Lower Threshold 3").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL HR Lower Threshold 3").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
6 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcLThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LUH3
MML Full Name
AMR PPC UL HR Lower Threshold 3
Segment Level Parameter
-
Table 236
360
AMR PPC UL HR Lower Threshold 3 (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 236
9.44
AMR PPC UL HR Lower Threshold 3 (Cont.)
AMR PPC UL HR Lower Threshold 4 (LUH4)
Parameter name
AMR PPC UL HR Lower Threshold 4
Abbreviated name
amrPpcUlHrLowerThreshold4
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc lower
threshold ul Rx qual AMR HR (LURH) + 1 is used and the
lower border for a range where pc lower threshold ul Rx
qual AMR HR (LURH) + 2 is used to trigger a power
increase due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL HR Lower Threshold 4").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL HR Lower Threshold 4").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
0 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcLThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the BTS power increase.
Defined for the default HR AMR set.
Parameter relationships
-
Table 237
DN9813866
AMR PPC UL HR Lower Threshold 4
Id:0900d8058089b05f
Confidential
361
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
LUH4
MML Full Name
AMR PPC UL HR Lower Threshold 4
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 237
9.45
AMR PPC UL HR Lower Threshold 4 (Cont.)
AMR PPC UL HR Upper Threshold 1 (UUH1)
Parameter name
AMR PPC UL HR Upper Threshold 1
Abbreviated name
amrPpcUlHrUpperThreshold1
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold ul Rx qual AMR HR (UURH) - 2 is used and the
lower border for a range where pc upper threshold ul Rx
qual AMR HR (UURH) - 1 is used to trigger a power
decrease due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL HR Upper Threshold 1").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL HR Upper Threshold 1").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
30 dB
Table 238
362
AMR PPC UL HR Upper Threshold 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcUThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power decrease.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UUH1
MML Full Name
AMR PPC UL HR Upper Threshold 1
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 238
9.46
AMR PPC UL HR Upper Threshold 2 (UUH2)
Parameter name
AMR PPC UL HR Upper Threshold 2
Abbreviated name
amrPpcUlHrUpperThreshold2
Managed object
BSC
Multiplicity
1
Table 239
DN9813866
AMR PPC UL HR Upper Threshold 1 (Cont.)
AMR PPC UL HR Upper Threshold 2
Id:0900d8058089b05f
Confidential
363
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold ul Rx qual AMR HR (UURH) - 1 is used and the
lower border for a range where pc upper threshold ul Rx
qual AMR HR (UURH) is used to trigger a power
decrease due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL HR Upper Threshold 2").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL HR Upper Threshold 2").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
18 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcUThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power decrease.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UUH2
MML Full Name
AMR PPC UL HR Upper Threshold 2
Segment Level Parameter
-
Table 239
364
AMR PPC UL HR Upper Threshold 2 (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 239
9.47
AMR PPC UL HR Upper Threshold 2 (Cont.)
AMR PPC UL HR Upper Threshold 3 (UUH3)
Parameter name
AMR PPC UL HR Upper Threshold 3
Abbreviated name
amrPpcUlHrUpperThreshold3
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold ul Rx qual AMR HR (UURH) is used and the
lower border for a range where pc upper threshold ul Rx
qual AMR HR (UURH) + 1 is used to trigger a power
decrease due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL HR Upper Threshold 3").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL HR Upper Threshold 3").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
6 dB
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcUThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power decrease.
Defined for the default HR AMR set.
Parameter relationships
-
Table 240
DN9813866
AMR PPC UL HR Upper Threshold 3
Id:0900d8058089b05f
Confidential
365
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UUH3
MML Full Name
AMR PPC UL HR Upper Threshold 3
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 240
9.48
AMR PPC UL HR Upper Threshold 3 (Cont.)
AMR PPC UL HR Upper Threshold 4 (UUH4)
Parameter name
AMR PPC UL HR Upper Threshold 4
Abbreviated name
amrPpcUlHrUpperThreshold4
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the border of UL power
ranges for the AMR Progressive Power Control algorithm. This is the upper border for a range where pc upper
threshold ul Rx qual AMR HR (UURH) + 1 is used and the
lower border for a range where pc upper threshold ul Rx
qual AMR HR (UURH) + 2 is used to trigger a power
decrease due to UL quality.
When this threshold defines the upper border for the
range, the threshold value is not part of the range (that is,
when power < "AMR PPC UL HR Upper Threshold 4").
When this threshold defines the lower border for the
range, the threshold value is part of the range (that is,
when power >= "AMR PPC UL HR Upper Threshold 4").
The value of this parameter is attenuation from the peak
power of the mobile (defined by classmark).
Additional information
-
Range
0...30
Step
2
Unit
dB
Formula for getting internal
value
internal_value = gui_value / 2
Default value
0 dB
Table 241
366
AMR PPC UL HR Upper Threshold 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Default value notes
MML default
Required on Creation
mandatory
Special value
Not used (255)
Related functions
Power Control
Modification
On-Line
Modified
-
Related parameters
amrPocHrPcUThrUlRxQual of BTS - With this parameter
you define the threshold level of the downlink signal
quality measurements for the MS power decrease.
Defined for the default HR AMR set.
Parameter relationships
-
Related options
•
Progressive AMR Power Control Algorithm (106)
(optional) AND AMR HR (72) (optional)
Related features
•
BSS20776: Progressive AMR Power Control
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEX, EEO
MML Abbreviated Name
UUH4
MML Full Name
AMR PPC UL HR Upper Threshold 4
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 241
9.49
AMR set grades enabled (ASG)
Parameter name
AMR Set Grades Enabled
Abbreviated name
amrSetGradesEnabl
Managed object
BSC
Multiplicity
1
Description
With this parameter you define whether codec mode set
downgrades during internal HOs and upgrades after
internal HOs are applied or not.
Additional information
-
Range
downgrades and upgrades are not applied (N) (0), downgrades and upgrades are applied (Y) (1)
Step
-
Unit
-
Table 242
DN9813866
AMR PPC UL HR Upper Threshold 4 (Cont.)
AMR Set Grades Enabled
Id:0900d8058089b05f
Confidential
367
Base Station Controller (BSC) radio network object parameters
Formula for getting internal
value
BSS Radio Network Parameter Dictionary
gui ==> internal
downgrades and upgrades are not applied (N) ==> 0
downgrades and upgrades are applied (Y) ==> 1
Default value
downgrades and upgrades are not applied (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
AMR HR (72) (optional) OR AMR FR (50) (optional)
Related features
•
BSS20249: AMR FR Licence Control
Interfaces
•
•
RACApp <-> RAC
BSC <-> RAC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
ASG
MML Full Name
AMR set grades enabled
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 242
9.50
AMR upper limit for FR resources (AHRU)
Parameter name
AMR Upper Limit For FR Resources
Abbreviated name
amrLoadDepTchRateUpper
Managed object
BSC
Multiplicity
1
Description
The parameter controls the AMR TCH channel rate
determination on the BSC level according to the cell
load in traffic channel allocation. With this parameter you define the upper limit for the percentage of
free full rate resources. AMR Full rate TCHs are
allocated when the number of free full rate
resources exceeds the value of the parameter.
Additional information
-
Table 243
368
AMR Set Grades Enabled (Cont.)
AMR Upper Limit For FR Resources
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Range
0...100
Step
1
Unit
%
Formula for getting
internal value
internal_value = gui_value
Default value
60 %
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
amrLoadDepTchRateLower of BSC - AMR Upper
Limit For FR Resources is applied together with
AMR lower limit for FR resources in an individual
SEG if no SEG-specific channel rate control rules
have been specified with the parameters AMR
lower limit for SEG FR resources and AMR upper
limit for SEG FR resources. If this parameter´s
value is smaller than the value of the AMR lower
limit for FR resources, then the effect of these two
BSC level channel rate control parameters is deactivated.
amrSegLoadDepTchRateLower of BTS - AMR
Upper Limit For FR Resources is applied together
with AMR lower limit for FR resources in an individual SEG if no SEG-specific channel rate control
rules have been specified with the parameters AMR
lower limit for SEG FR resources and AMR upper
limit for SEG FR resources.
amrSegLoadDepTchRateUpper of BTS - AMR
Upper Limit For FR Resources is applied together
with AMR lower limit for FR resources in an individual SEG if no SEG-specific channel rate control
rules have been specified with the parameters AMR
lower limit for SEG FR resources and AMR upper
limit for SEG FR resources.
Parameter relationships
-
Related options
•
Load based AMR packing (111) (optional) AND
AMR HR (72) (optional)
Feature dependencies
•
BSS21154: Load based AMR packing
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
Table 243
DN9813866
AMR Upper Limit For FR Resources (Cont.)
Id:0900d8058089b05f
Confidential
369
Base Station Controller (BSC) radio network object parameters
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
AHRU
MML Full Name
AMR upper limit for FR resources
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 243
9.51
BSS Radio Network Parameter Dictionary
AMR Upper Limit For FR Resources (Cont.)
A-If AF1 WFQ weight (AAF1WF)
Parameter name
A-If AF1 WFQ Weight
Abbreviated name
AIfAf1WfqWeight
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter user define the Weighted Fair
Queuing (WFQ) weight assigned to the Assured
Forwarding Class 1 (AF1) scheduling queue in A
interface.
This is one of the traffic scheduling parameters and
it has meaning only if same interface terminates
several planes with different QoS. Parameter is
used in BTS and ETP.
Additional information
-
Range
1...10000
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
5000
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Table 244
370
A-If AF1 WFQ Weight
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Parameter relationships
-
Related options
AoIP Transcoder in BSS (157) or
AoIP Transcoder in MGW (158)
Feature dependencies
BSS21341: A Over IP
Interfaces
RAC <-> BSCRACApp <-> RAC
References
-
File based provisioning
supported
true
MML Abbreviated Name
AAF1WF
MML Commands
EEY, EEO
MML Full Name
A-If AF1 WFQ weight
Segment Level Parameter
-
Table 244
9.52
A-If AF1 WFQ Weight (Cont.)
A-If AF2 WFQ weight (AAF2WF)
Parameter name
A-If AF2 WFQ Weight
Abbreviated name
AIfAf2WfqWeight
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter user define the Weighted Fair
Queuing (WFQ) weight assigned to the Assured
Forwarding Class 2 (AF2) scheduling queue in A
interface.
This is one of the traffic scheduling parameters and
it has meaning only if same interface terminates
several planes with different QoS. Parameter is
used in BTS and ETP.
Additional information
-
Range
1...10000
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
5000
Default value notes
-
Table 245
DN9813866
A-If AF2 WFQ Weight
Id:0900d8058089b05f
Confidential
371
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
AoIP Transcoder in BSS (157) or
AoIP Transcoder in MGW (158)
Feature dependencies
BSS21341: A Over IP
Interfaces
RAC <-> BSCRACApp <-> RAC
References
-
File based provisioning
supported
true
MML Abbreviated Name
AAF2WF
MML Commands
EEY, EEO
MML Full Name
A-If AF2 WFQ weight
Segment Level Parameter
-
Table 245
9.53
A-If AF2 WFQ Weight (Cont.)
A-If AF3 WFQ weight (AAF3WF)
Parameter name
A-If AF3 WFQ Weight
Abbreviated name
AIfAf3WfqWeight
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter user define the Weighted Fair
Queuing (WFQ) weight assigned to the Assured
Forwarding Class 3 (AF3) scheduling queue in A
interface.
This is one of the traffic scheduling parameters and
it has meaning only if same interface terminates
several planes with different QoS. Parameter is
used in BTS and ETP.
Additional information
-
Range
1...10000
Table 246
372
A-If AF3 WFQ Weight
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
5000
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
AoIP Transcoder in BSS (157) or
AoIP Transcoder in MGW (158)
Feature dependencies
BSS21341: A Over IP
Interfaces
RAC <-> BSCRACApp <-> RAC
References
-
File based provisioning
supported
true
MML Abbreviated Name
AAF3WF
MML Commands
EEY, EEO
MML Full Name
A-If AF3 WFQ weight
Segment Level Parameter
-
Table 246
9.54
A-if AF4 WFQ weight (AAF4WF)
Parameter name
A-If AF4 WFQ Weight
Abbreviated name
AIfAf4WfqWeight
3GPP name
-
Managed Object
BSC
Multiplicity
1
Table 247
DN9813866
A-If AF3 WFQ Weight (Cont.)
A-If AF4 WFQ Weight
Id:0900d8058089b05f
Confidential
373
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter user define the Weighted Fair
Queuing (WFQ) weight assigned to the Assured
Forwarding Class 4 (AF4) scheduling queue in A
interface.
This is one of the traffic scheduling parameters and
it has meaning only if same interface terminates
several planes with different QoS. Parameter is
used in BTS and ETP.
Additional information
-
Range
1...10000
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
5000
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
AoIP Transcoder in BSS (157) or
AoIP Transcoder in MGW (158)
Feature dependencies
BSS21341: A Over IP
Interfaces
RAC <-> BSCRACApp <-> RAC
References
-
File based provisioning
supported
true
MML Abbreviated Name
AAF4WF
MML Commands
EEY, EEO
MML Full Name
A-if AF4 WFQ weight
Segment Level Parameter
-
Table 247
374
A-If AF4 WFQ Weight (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.55
Base Station Controller (BSC) radio network object parameters
A-If BE WFQ weight (ABEWFQ)
Parameter name
A-If BE WFQ Weight
Abbreviated name
AIfBeWfqWeight
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter user define best effort (BE)
weight assigned to the BE scheduling queue in A
interface.
This is one of the traffic scheduling parameters and
it has meaning only if same interface terminates
several planes with different QoS. Parameter is
used in BTS and ETP.
Additional information
-
Range
1...10000
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
5000
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
AoIP Transcoder in BSS (157) or
AoIP Transcoder in MGW (158)
Feature dependencies
BSS21341: A Over IP
Interfaces
RAC <-> BSCRACApp <-> RAC
References
-
File based provisioning
supported
true
MML Abbreviated Name
ABEWFQ
MML Commands
EEY, EEO
MML Full Name
A-If BE WFQ weight
Table 248
DN9813866
A-If BE WFQ Weight
Id:0900d8058089b05f
Confidential
375
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
Table 248
9.56
BSS Radio Network Parameter Dictionary
-
A-If BE WFQ Weight (Cont.)
A-IF CS U-PLANE DSCP PHB TC IN BSS (ADSCPB)
Parameter name
A-If CS U-plane DSCP PHB TC in BSS
Abbreviated name
AIfCsUplaneDscpPhbTcInBss
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter user define mapping of CS UPlane traffic class to the Diffentiated Services Code
Point (DSCP), field in the IP header that indicates
the Per-Hop Behaviour (PHB) that a packet
receives, on A interface when Transcoder (TC) is in
BSS.
Mapping of the traffic class are done in BSC level.
BCSU and Exchange Terminal for Packet transport
(ETP) shall do egress packet markings for different
traffic classes based on the user
defined values.
Additional information
Range: DSCP value shall be give either binary
string (000000-111111) or in hexadecimal (0-63)
Range
BE (0),
AF11 (10),
AF21 (18),
AF31 (26),
AF41 (34),
EF (46)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
BE ==> 0
AF11 ==> 10
AF21 ==> 18
AF31 ==> 26
AF41 ==> 34
EF ==> 46
Table 249
376
A-If CS U-plane DSCP PHB TC in BSS
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Default value
EF (46)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
AoIP Transcoder in BSS (157) or
AoIP Transcoder in MGW (158)
Feature dependencies
BSS21341: A Over IP
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
ADSCPB
MML Commands
EEY, EEO
MML Full Name
A-IF CS U-PLANE DSCP PHB TC IN BSS
Segment Level Parameter
-
Table 249
9.57
A-IF CS U-PLANE DSCP PHB TC IN MGW (ADSCPM)
Parameter name
A-If CS U-plane DSCP PHB TC in MGW
Abbreviated name
AIfCsUplaneDscpPhbTcInMgw
3GPP name
-
Managed Object
BSC
Multiplicity
1
Table 250
DN9813866
A-If CS U-plane DSCP PHB TC in BSS (Cont.)
A-If CS U-plane DSCP PHB TC in MGW
Id:0900d8058089b05f
Confidential
377
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter user define mapping of CS UPlane traffic class to the Differentiated Services
Code Point (DSCP), field in the IP header that indicates the Per-Hop Behaviour (PHB) that a packet
receives, on A interface when Transcoder (TC) is in
Media Gateway (MGW).
Mapping of the traffic class are done in BSC level.
BCSU and Exchange Terminal for Packet transport
(ETP) shall do egress packet markings for different
traffic classes based on the user defined values.
Additional information
Range:
DSCP value shall be give either binary string
(000000-111111) or in hexadecimal (0-63)
Range
BE (0),
AF11 (10),
AF21 (18),
AF31 (26),
AF41 (34),
EF (46)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
BE ==> 0
AF11 ==> 10
AF21 ==> 18
AF31 ==> 26
AF41 ==> 34
EF ==> 46
Default value
AF41 (34)
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
AoIP Transcoder in BSS (157) or
AoIP Transcoder in MGW (158)
Table 250
378
A-If CS U-plane DSCP PHB TC in MGW (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Feature dependencies
BSS21341: A Over IP
Interfaces
RAC <-> BSCRACApp <-> RAC
References
-
File based provisioning
supported
true
MML Abbreviated Name
ADSCPM
MML Commands
EEY, EEO
MML Full Name
A-IF CS U-PLANE DSCP PHB TC IN MGW
Segment Level Parameter
-
Table 250
9.58
Base Station Controller (BSC) radio network object parameters
A-If CS U-plane DSCP PHB TC in MGW (Cont.)
abis C-plane to DSCP mapping (ACP)
Parameter name
Abis C-plane to DSCP Mapping
Abbreviated name
tmAbisCplane
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define C-plane traffic to
DSCP mapping.
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
BE (000000) (0), AF11 (001010) (10), AF21
(010010) (18), AF31 (011010) (26), AF41 (100010)
(34), EF (101110) (46)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
BE
(000000) ==> 0
AF11 (001010) ==> 10
AF21 (010010) ==> 18
AF31 (011010) ==> 26
AF41 (100010) ==> 34
EF
Default value
Table 251
DN9813866
(101110) ==> 46
EF (101110) (46)
Abis C-plane to DSCP Mapping
Id:0900d8058089b05f
Confidential
379
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value notes
EF
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
OR Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS21440: Packet Abis over TDM
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: BSS21440 - Packet Abis over TDM
StandardNSN reference: BSS21454 - Packet Abis
over IP/Eth
File based provisioning
supported
true
MML Abbreviated Name
ACP
MML Commands
EEY, EEO
MML Full Name
abis C-plane to DSCP mapping
Segment Level Parameter
-
Table 251
9.59
Abis C-plane to DSCP Mapping (Cont.)
abis M-plane to DSCP mapping (AMP)
Parameter name
Abis M-plane to DSCP Mapping
Abbreviated name
tmAbisMplane
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define M-plane traffic to
DSCP mapping.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Table 252
380
Abis M-plane to DSCP Mapping
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Additional information
-
Range
BE (000000) (0),
AF11 (001010) (10),
AF21 (010010) (18),
AF31 (011010) (26),
AF41 (100010) (34),
EF (101110) (46)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
BE
(000000) ==> 0
AF11 (001010) ==> 10
AF21 (010010) ==> 18
AF31 (011010) ==> 26
AF41 (100010) ==> 34
EF
(101110) ==> 46
Default value
BE (000000) (0)
Default value notes
BE
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS21440: Packet Abis over TDM
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: BSS21440 - Packet Abis over TDM
StandardNSN reference: BSS21454 - Packet Abis
over IP/Eth
File based provisioning
supported
true
MML Abbreviated Name
AMP
MML Commands
EEY, EEO
Table 252
DN9813866
Abis M-plane to DSCP Mapping (Cont.)
Id:0900d8058089b05f
Confidential
381
Base Station Controller (BSC) radio network object parameters
MML Full Name
abis M-plane to DSCP mapping
Segment Level Parameter
-
Table 252
9.60
BSS Radio Network Parameter Dictionary
Abis M-plane to DSCP Mapping (Cont.)
abis U-plane CS to DSCP mapping (AUCS)
Parameter name
Abis U-plane CS to DSCP Mapping
Abbreviated name
tmAbisUplaneCs
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define U-plane CS traffic to
DSCP mapping.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
BE (000000) (0),
AF11 (001010) (10),
AF21 (010010) (18),
AF31 (011010) (26),
AF41 (100010) (34),
EF (101110) (46)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
BE
(000000) ==> 0
AF11 (001010) ==> 10
AF21 (010010) ==> 18
AF31 (011010) ==> 26
AF41 (100010) ==> 34
EF
Default value
AF41 (100010) (34)
Default value notes
AF41
Required on creation
optional
Child parameters
-
Table 253
382
(101110) ==> 46
Abis U-plane CS to DSCP Mapping
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS21440: Packet Abis over TDM
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: BSS21440 - Packet Abis over TDM
StandardNSN reference: BSS21454 - Packet Abis
over IP/Eth
File based provisioning
supported
true
MML Abbreviated Name
AUCS
MML Commands
EEY, EEO
MML Full Name
abis U-plane CS to DSCP mapping
Segment Level Parameter
-
Table 253
9.61
Abis U-plane CS to DSCP Mapping (Cont.)
abis U-plane PS to DSCP mapping (AUPS)
Parameter name
Abis U-plane PS to DSCP Mapping
Abbreviated name
tmAbisUplanePs
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define U-plane PS traffic to
DSCP mapping.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
Table 254
DN9813866
-
Abis U-plane PS to DSCP Mapping
Id:0900d8058089b05f
Confidential
383
Base Station Controller (BSC) radio network object parameters
Range
BSS Radio Network Parameter Dictionary
BE (000000) (0),
AF11 (001010) (10),
AF21 (010010) (18),
AF31 (011010) (26),
AF41 (100010) (34),
EF (101110) (46)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
BE
(000000) ==> 0
AF11 (001010) ==> 10
AF21 (010010) ==> 18
AF31 (011010) ==> 26
AF41 (100010) ==> 34
EF
(101110) ==> 46
Default value
AF31 (011010) (26)
Default value notes
AF31
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS21440: Packet Abis over TDM
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: BSS21440 - Packet Abis over TDM
StandardNSN reference: BSS21454 - Packet Abis
over IP/Eth
File based provisioning
supported
true
MML Abbreviated Name
AUPS
MML Commands
EEY, EEO
MML Full Name
abis U-plane PS to DSCP mapping
Table 254
384
Abis U-plane PS to DSCP Mapping (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
Table 254
9.62
Abis U-plane PS to DSCP Mapping (Cont.)
Background traffic class scheduling weight for ARP 1
(BGSW1)
Parameter name
Background Traffic Class Scheduling Weight For ARP 1
Abbreviated name
schedulingWeight_backgroundARP1
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the scheduling weight for
proportion of residual bandwidth allocation and retention
priority value 1 for background traffic class.
Additional information
-
Range
1...100
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
20
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
BSS11111: Enhanced Quality of Service, EQoS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEV, EEO
MML Abbreviated Name
BGSW1
MML Full Name
Background traffic class scheduling weight for ARP 1
Segment Level Parameter
-
Table 255
DN9813866
-
Background Traffic Class Scheduling Weight For ARP 1
Id:0900d8058089b05f
Confidential
385
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 255
9.63
Background traffic class scheduling weight for ARP 2
(BGSW2)
Parameter name
Background Traffic Class Scheduling Weight For ARP 2
Abbreviated name
schedulingWeight_backgroundARP2
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the scheduling weight for
proportion of residual bandwidth allocation and retention
priority value 2 for background traffic class.
Additional information
-
Range
1...100
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
10
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
BSS11111: Enhanced Quality of Service, EQoS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEV, EEO
MML Abbreviated Name
BGSW2
MML Full Name
Background traffic class scheduling weight for ARP 2
Segment Level Parameter
-
Table 256
386
Background Traffic Class Scheduling Weight For ARP 1 (Cont.)
Background Traffic Class Scheduling Weight For ARP 2
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 256
9.64
Background traffic class scheduling weight for ARP 3
(BGSW3)
Parameter name
Background Traffic Class Scheduling Weight For ARP 3
Abbreviated name
schedulingWeight_backgroundARP3
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the scheduling weight for
proportion of residual bandwidth allocation and retention
priority value 3 for background traffic class.
Additional information
-
Range
1...100
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
5
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
BSS11111: Enhanced Quality of Service, EQoS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEV, EEO
MML Abbreviated Name
BGSW3
MML Full Name
Background traffic class scheduling weight for ARP 3
Segment Level Parameter
-
Table 257
DN9813866
Background Traffic Class Scheduling Weight For ARP 2 (Cont.)
Background Traffic Class Scheduling Weight For ARP 3
Id:0900d8058089b05f
Confidential
387
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 257
9.65
Background Traffic Class Scheduling Weight For ARP 3 (Cont.)
BCSU load threshold (BCSUL)
Parameter name
BCSU Load Threshold
Abbreviated name
bcsuLoadThr
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the threshold for the proportion of rejected measurement results in all measurement results. An overload in the BCSU/BCXU unit causes
the rejections. If this threshold is exceeded, the
BCSU/BCXU unit is regarded as overloaded, and the
BSC generates the relevant alarm.
MML Range and Step: 0..10000 = 0..100% (step size is
0.01%).
Additional information
-
Range
0...10000
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
150
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
BCSUL
MML Full Name
BCSU load threshold
Table 258
388
RAC <-> RACApp
RAC <-> BSC
BCSU Load Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 258
9.66
BIM confidence probability (BCP)
Parameter name
BIM Confidence Probability
Abbreviated name
bimConfidenceProb
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the level of confidence for
the estimation used to build a background interference
matrix. It gives the share of users experiencing a C/I
equal to or greater than the C/I contained in the matrix.
Additional information
-
Range
50...95
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
80 %
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
BCP
MML Full Name
BIM confidence probability
Table 259
DN9813866
BCSU Load Threshold (Cont.)
BIM Confidence Probability
Id:0900d8058089b05f
Confidential
389
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
BSS Radio Network Parameter Dictionary
-
File Based Provisioning sup- true
ported
Table 259
9.67
BIM interference threshold (BIT)
Parameter name
BIM Interference Threshold
Abbreviated name
bimInterfThreshold
Managed object
BSC
Multiplicity
1
Description
With this parameter you define an upper limit for C/I
values which are considered as relevant for the interference estimations. C/I values above the Interference
threshold can be discarded during the BIM update procedure.
Additional information
-
Range
0...35
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
35
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
BIT
MML Full Name
BIM interference threshold
Table 260
390
BIM Confidence Probability (Cont.)
BIM Interference Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 260
9.68
BIM Interference Threshold (Cont.)
BIM update guard time (BUGT)
Parameter name
BIM Update Guard Time
Abbreviated name
bimUpdateGuardTime
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the number of BIM
update periods that the DFCA algorithm allows for
a neighbouring cell without update. If during the
update guard time the neighbouring cell is not
included in any BIM update for the cell, it is
removed from the BIM table of the cell.
Value range for guard time is 0...62 BIM update
periods. Value 63 indicates that a neighbour is not
removed from the BIM even if the neighbour is not
included in any new BIM update.
Additional information
-
Range
0...63
Step
1
Unit
period
Formula for getting
internal value
internal_value = gui_value
Default value
62 period
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70)
Feature dependencies
•
BSS11052: Dynamic Frequency and Channel
Allocation
Table 261
DN9813866
BIM Update Guard Time
Id:0900d8058089b05f
Confidential
391
Base Station Controller (BSC) radio network object parameters
Interfaces
•
•
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
BUGT
MML Full Name
BIM update guard time
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 261
9.69
BSS Radio Network Parameter Dictionary
RAC <-> RACApp
RAC <-> BSC
BIM Update Guard Time (Cont.)
bim update period (BUP)
Parameter name
BIM Update Period
Abbreviated name
bimUpdatePeriod
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the period between successive background interference matrix updates. Therefore, it is the length of the data collecting period for a
single BIM update.
NOTE:
MML range:
10 min to 60 min (10 min step size);
2h to 6h (60 min step size);
12h and 24h;
0 turns off the BIM update procedure
Additional information
-
Range
turns off the BIM update procedure (0), 10 min (10), 20
min (20), 30 min (30), 40 min (40), 50 min (50), 1 h (60),
2 h (120), 3 h (180), 4 h (240), 5 h (300), 6 h (360), 12 h
(720), 24 h (1440)
Step
-
Unit
-
Table 262
392
BIM Update Period
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Formula for getting internal
value
gui ==> internal
turns off the BIM update procedure ==> 0
10 min ==> 10
20 min ==> 20
30 min ==> 30
40 min ==> 40
50 min ==> 50
1 h ==> 60
2 h ==> 120
3 h ==> 180
4 h ==> 240
5 h ==> 300
6 h ==> 360
12 h ==> 720
24 h ==> 1440
Default value
2 h (120)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
BUP
MML Full Name
bim update period
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 262
DN9813866
BIM Update Period (Cont.)
Id:0900d8058089b05f
Confidential
393
Base Station Controller (BSC) radio network object parameters
9.70
BSS Radio Network Parameter Dictionary
BIM update scaling factor (BUSF)
Parameter name
BIM Update Scaling Factor
Abbreviated name
bimUpdateScalingFactor
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the weighting factor for
the C/I value defined during the latest BIM update period
when this is combined with the long term C/I statistics.
Additional information
-
Range
0...1
Step
0.1
Unit
-
Formula for getting internal
value
internal_value = gui_value * 10
Default value
0.5
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
BUSF
MML Full Name
BIM update scaling factor
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 263
394
BIM Update Scaling Factor
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.71
Base Station Controller (BSC) radio network object parameters
BTS site battery backup forced HO timer (TIM)
Parameter name
BTS Site Battery Backup Forced HO Timer
Abbreviated name
batteryBackupTimer
Managed object
BSC
Multiplicity
1
Description
The parameter defines the maximum time period
during which handover is attempted in TRX.
NOTE: This parameter is valid only if Adjustable
Intelligent Shutdown for FlexiEDGE or Adjustable
Intelligent Shutdown for MetroSite, UltraSite and
Talk-family licence (according to site type) is
ON/CONFIG OR the FIFILE/PRFILE option for
intelligent shutdown is ON, see below for
FIFILE/PRFILE options:
- MetroSite: BTS_METRO_SITE_BATBU_PR
- Talk-family: BTS_SITE_BATBU_PROC_A AND
BTS_SIT_BATBU_PROC
- UltraSite, Flexi EDGE, BTSplus and Flexi Multiradio and Horizon: BTS_ULTRA_SITE_BATBU_PR
Additional information
-
Range
1...500
Step
1
Unit
s
Formula for getting
internal value
internal_value = gui_value
Default value
30 s
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 264
DN9813866
BTS Site Battery Backup Forced HO Timer
Id:0900d8058089b05f
Confidential
395
Base Station Controller (BSC) radio network object parameters
Related options
•
Remote Degration Of BTS Service Under TRX
Shutdown (2) (optional) OR BTS Metro Site
Batbu Pr (73) (optional) OR BTS Ultra Site
Batbu Pr (74) (optional) OR Adjustable Intelligent Shutdown, 2G Flexi (101) (optional) OR
Adjustable Intelligent Shutdown for MetroSite,
UltraSite, Talk-family (102) (optional)
Feature dependencies
•
•
BSS20151: Adjustable Intelligent Shutdown
BSS20903: Adjustable Intelligent Shutdown,
2G Flexi
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
TIM
MML Full Name
BTS site battery backup forced HO timer
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 264
9.72
BTS Site Battery Backup Forced HO Timer (Cont.)
backhaul timer duration start reaction (BTON)
Parameter name
Backhaul Timer Duration Start Reaction
Abbreviated name
bhTimerDurStartReact
3GPP name
-
Managed Object
BSC
Multiplicity
1
Table 265
396
BSS Radio Network Parameter Dictionary
Backhaul Timer Duration Start Reaction
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
With this parameter you define the timer of the
period when the related backhaul congestion has to
be present in order to be defined as "detected". It is
related to average window concerning congestion
algorithm. The algorithm handling these measurements takes into account as average window a time
period related to filtering timers (T_on_backhaul
and T_off_backhaul).
NOTE: The values of these timers are valid both for
UL and for DL direction.
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
1...300
Step
1
Units
s
Formula for getting
internal value
internal_value =gui_value
Default value
4
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
BTON
MML Commands
EEY, EEO
MML Full Name
backhaul timer duration start reaction
Table 265
DN9813866
Backhaul Timer Duration Start Reaction (Cont.)
Id:0900d8058089b05f
Confidential
397
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
Table 265
9.73
BSS Radio Network Parameter Dictionary
-
Backhaul Timer Duration Start Reaction (Cont.)
backhaul timer duration stop reaction (BTOFF)
Parameter name
Backhaul Timer Duration Stop Reaction
Abbreviated name
bhTimerDurStopReact
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the timer of the
period when the related backhaul congestion has to
be absent in order to be defined as "not detected".
It is related to average window concerning congestion algorithm. The algorithm handling these measurements takes into account as average window a
time period related to filtering timers
(T_on_backhaul and T_off_backhaul).
NOTE: The values of these timers are valid both for
UL and for DL direction.
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
1...600
Step
1
Units
s
Formula for getting
internal value
internal_value =gui_value
Default value
10
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 266
398
Backhaul Timer Duration Stop Reaction
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
BTOFF
MML Commands
EEY, EEO
MML Full Name
backhaul timer duration stop reaction
Segment Level Parameter
-
Table 266
9.74
Backhaul Timer Duration Stop Reaction (Cont.)
C/I Target 14.4 (CIT)
Parameter name
C/I Target 14.4
Abbreviated name
dfca144Connection_ciTarget
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the target C/I value for
circuit switched data connections of 14.4 kbit/s.
NOTE: The parameter value must be equal to or greater
than soft blocking C/I 14.4
NOTE: MML modification:
Parameter is modifiable if options Dynamic Frequency
And Channel Allocation (70) AND (HSCSD_PRM OR
PRM_144) are ON. Options (HSCSD_PRM and
PRM_144) are hidden in MML and available if the
operator has purchased the feature.
Additional information
-
Range
0...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
16 dB
Default value notes
-
Table 267
DN9813866
C/I Target 14.4
Id:0900d8058089b05f
Confidential
399
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
dfca144Connection_softBlockingCi of BSC - The parameter value must be equal to or greater than soft blocking
C/I 14.4
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70) (optional) AND ( Data 144 Usage (69)
(optional) OR High Speed Circuit Switched Data
(HSCSD - TCSM2) (25) (optional) )
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
CIT
MML Full Name
C/I Target 14.4
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 267
9.75
C/I Target 14.4 (Cont.)
C/I target AMR FR (CIAF)
Parameter name
C/I Target AMR FR
Abbreviated name
dfcaAmrFrConnection_ciTarget
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the target C/I value for full
rate AMR and full rate WB-AMR speech connections.
Note:
The parameter value must be equal to or greater than soft
blocking C/I AMR FR.
Additional information
-
Range
0...63
Step
1
Unit
dB
Table 268
400
C/I Target AMR FR
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Formula for getting internal
value
internal_value = gui_value
Default value
12 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70) (optional) AND ( AMR FR (50) (optional)
OR Wideband AMR (133) (optional) )
Related features
•
•
•
BSS20960: Wideband AMR
BSS11052: Dynamic Frequency and Channel Allocation
BSS20249: AMR FR Licence Control
•
•
RAC <-> RACApp
RAC <-> BSC
Interfaces
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
CIAF
MML Full Name
C/I target AMR FR
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 268
9.76
C/I Target AMR FR (Cont.)
C/I target AMR HR (CIAH)
Parameter name
C/I Target AMR HR
Abbreviated name
dfcaAmrHrConnection_ciTarget
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the target C/I value
for half rate AMR speech connections.
Note: The parameter value must be equal to or
greater than soft blocking C/I AMR HR.
Additional information
Table 269
DN9813866
-
C/I Target AMR HR
Id:0900d8058089b05f
Confidential
401
Base Station Controller (BSC) radio network object parameters
Range
0...63
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
12 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
activationState of BSC - The parameter value must
be equal to or greater than soft blocking C/I AMR
HR.
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70) (optional) AND AMR HR
(72) (optional)
Feature dependencies
•
BSS11052: Dynamic Frequency and Channel
Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
CIAH
MML Full Name
C/I target AMR HR
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 269
9.77
C/I Target AMR HR (Cont.)
C/I Target FR (CIF)
Parameter name
C/I Target FR
Abbreviated name
dfcaFrConnection_ciTarget
Managed object
BSC
Table 270
402
BSS Radio Network Parameter Dictionary
C/I Target FR
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Multiplicity
1
Description
With this parameter you define the target C/I value for full
rate and EFR speech connections, and for circuit
switched data connections up to 9.6 kbit/s.
Note: The parameter value must be equal to or greater
than soft blocking C/I FR.
Additional information
-
Range
0...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
14 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
activationState of BSC - The parameter value must be
equal to or greater than soft blocking C/I FR.
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
CIF
MML Full Name
C/I Target FR
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 270
9.78
C/I Target GPRS (CIGP)
Parameter name
DFCA C/I Target GPRS
Abbreviated name
dfcaCiTargetGPRS
Table 271
DN9813866
C/I Target FR (Cont.)
DFCA C/I Target GPRS
Id:0900d8058089b05f
Confidential
403
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the target C/I value for
GPRS connection on DFCA layer.
Note: DFCA Soft Blocking C/I GPRS is also related to this
parameter, DFCA C/I Target GPRS value should be
defined egual or greater than value for DFCA Soft
Blocking C/I GPRS.
Additional information
-
Range
0...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
20 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
DFCA C/I Target GPRS value should be defined equal or
greater than value for DFCA Soft Blocking C/I GPRS.
Related parameters
dfcaSoftBlockingCiGPRS of BSC - DFCA Soft Blocking
GPRS is used for setting threshold value for C/I that is the
lowest C/I acceptable for GPRS connection
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70) (optional) AND SDCCH and PS Data
Channels on DFCA TRX (136) (optional)
Related features
•
BSS21161: SDCCH and PS Data Channels on
DFCA TRX
BSS11052: Dynamic Frequency and Channel Allocation
•
•
•
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
CIGP
MML Full Name
C/I Target GPRS
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 271
404
DFCA C/I Target GPRS (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.79
Base Station Controller (BSC) radio network object parameters
C/I target HR (CIH)
Parameter name
C/I Target HR
Abbreviated name
dfcaHrConnection_ciTarget
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the target C/I value for half
rate speech connections.
Note: The parameter value must be equal to or greater
than soft blocking C/I HR.
Additional information
-
Range
0...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
14 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
activationState of BSC - The parameter value must be
equal to or greater than soft blocking C/I HR.
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70) (optional) AND Half Rate (17) (optional)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
CIH
MML Full Name
C/I target HR
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 272
DN9813866
C/I Target HR
Id:0900d8058089b05f
Confidential
405
Base Station Controller (BSC) radio network object parameters
9.80
C/I target OSC DFR (CIDFR)
Parameter name
C/I Target OSC DFR
Abbreviated name
ciTargetOscDfr
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the target C/I value
for double full rate connections.
Additional information
-
Range
0...63
Step
1
Units
dB
Formula for getting
internal value
internal_value = gui_value
Default value
12
Default value notes
-
Required on creation
optional
Modification
On-Line
Modified
-
Related parameters
softBlockingCiOscDfr of
BSC C/I Target OSC DFR parameter value must be
equal to or greater than Soft Blocking C/I OSC DFR
Parameter relationships
-
Related options
•
OSC Full Rate with SAIC MS (160) (optional)
AND DFCA (Dynamic Frequency And Channel
Allocation) Usage (70) (optional) AND AMR
FR (50) (optional)
Feature dependencies
•
BSS21309 OSC Half Rate With SAIC MS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
CIDFR
MML Commands
EEH, EEO
MML Full Name
C/I target OSC DFR
Table 273
406
BSS Radio Network Parameter Dictionary
C/I Target OSC DFR
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
Table 273
9.81
C/I Target OSC DFR (Cont.)
C/I target OSC DHR (CIDHR)
Parameter name
C/I Target OSC DHR
Abbreviated name
ciTargetOscDhr
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the target C/I value
for double half rate connections.
Additional information
-
Range
0...63
Step
1
Units
dB
Formula for getting
internal value
internal_value = gui_value
Default value
16
Default value notes
-
Required on creation
optional
Modification
On-Line
Modified
-
Related parameters
softBlockingCiOscDhr of BSC - C/I Target OSC
DHR parameter value must be equal to or greater
than Soft Blocking C/I OSC DHR
Parameter relationships
-
Related options
•
Double Half Rate with SAIC MS (146)
(optional) AND DFCA (Dynamic Frequency
And Channel Allocation) Usage (70) (optional)
AND AMR HR (72) (optional)
Feature dependencies
•
BSS21391 DFCA support for OSC
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
NSN reference: Orthogonal Sub Channel
BSS21309, BSS30385, BSS30390 IS,NSN reference: DFCA support for OSC BSS21391
Table 274
DN9813866
-
C/I Target OSC DHR
Id:0900d8058089b05f
Confidential
407
Base Station Controller (BSC) radio network object parameters
File based provisioning
supported
true
MML Abbreviated Name
CIDHR
MML Commands
EEH, EEO
MML Full Name
C/I target OSC DHR
Segment Level Parameter
-
Table 274
9.82
BSS Radio Network Parameter Dictionary
C/I Target OSC DHR (Cont.)
C/I Target SDCCH (CISD)
Parameter name
DFCA C/I Target SDCCH
Abbreviated name
dfcaCiTargetSDCCH
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the target C/I value
for SDCCH connection on DFCA layer.
Note: DFCA Soft Blocking C/I SDCCH is also
related to this parameter, DFCA C/I target SDCCH
value should be defined equal or greater than value
for DFCA Soft Blocking C/I SDCCH.
Additional information
-
Range
0...63
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
14 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
DFCA C/I Target SDCCH value should be defined
equal or greater than value for DFCA Soft Blocking
C/I SDCCH.
Table 275
408
DFCA C/I Target SDCCH
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related parameters
dfcaSoftBlockingCiSDCCH of BSC - DFCA Soft
Blocking C/I SDCCH is used for setting threshold
value for C/I that is the lowest C/I acceptable for
SDCCH connection
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70) (optional) AND SDCCH
and PS Data Channels on DFCA TRX (136)
(optional)
Feature dependencies
•
BSS21161: SDCCH and PS Data Channels on
DFCA TRX
BSS11052: Dynamic Frequency and Channel
Allocation
•
Interfaces
•
•
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
CISD
MML Full Name
C/I Target SDCCH
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 275
9.83
DFCA C/I Target SDCCH (Cont.)
C/I target UL offset (CIUL)
Parameter name
C/I Target UL Offset
Abbreviated name
ciTargetUlOffset
Managed object
BSC
Multiplicity
1
Description
With this parameter you define an offset that is added to
the C/I targets and soft blocking C/I limits of all connection types when uplink interference checks are performed.
Additional information
-
Range
-31...31
Step
1
Unit
dB
Table 276
DN9813866
RACApp <-> RAC
RAC <-> BSC
C/I Target UL Offset
Id:0900d8058089b05f
Confidential
409
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Formula for getting internal
value
internal_value = gui_value
Default value
0 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
CIUL
MML Full Name
C/I target UL offset
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 276
9.84
CN identity (CNID)
Parameter name
CN-ID
Abbreviated name
cnId
Managed object
BSC
Multiplicity
1
Description
With this parameter you define Core Network-ID
Additional information
-
Range
0...4095
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Table 277
410
C/I Target UL Offset (Cont.)
CN-ID
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94)
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
E7I, E7M, E7A
MML Abbreviated Name
CNID
MML Full Name
CN identity
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 277
9.85
CN-ID (Cont.)
CS load balancing value (LOAD)
Parameter name
CS Load Balancing Value
Abbreviated name
csLoadBalancingValue
Managed object
BSC
Multiplicity
1
Description
This parameter determines the load balancing technique
to be used in the BSC when Multipoint A is in use.
Additional information
-
Range
Not used (OFF) (0), Done with actual NRI values (1),
Done with number of available circuits (2)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Not used (OFF) ==> 0
Done with actual NRI values ==> 1
Done with number of available circuits ==> 2
Table 278
DN9813866
CS Load Balancing Value
Id:0900d8058089b05f
Confidential
411
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value
Not used (OFF) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94)
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I, E7M
MML Abbreviated Name
LOAD
MML Full Name
CS load balancing value
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 278
9.86
CS Load Balancing Value (Cont.)
CS MSC State (STATE)
Parameter name
CS MSC State
Abbreviated name
csMSCState
Managed object
BSC
Multiplicity
1
Description
This parameter determines MSC/MSS state for the
NAS Node method to be used in the BSC when
Multipoint A is in use.
WO-EX state means MSC working,
BAL-US value is used for barring only from load balancing function,
BAR-US value means that CN Node is totally
blocked from all connection establishments.
This value can be defined for each MSC/MSS
Additional information
-
Range
WO-EX (0), BAL-US (1), BAR-US (2)
Table 279
412
CS MSC State
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
WO-EX ==> 0
BAL-US ==> 1
BAR-US ==> 2
Default value
-
Default value notes
0
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csWeightFactor of BSC - Weight Factor parameters
needs to be re-adjusted if one or several
MSC/MSSs are set to BAR-US state.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94)
Feature dependencies
•
•
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I, E7M
MML Abbreviated Name
STATE
MML Full Name
CS MSC State
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 279
9.87
CS NAS node method (NASMETHOD)
Parameter name
CS NAS Node Method
Abbreviated name
csNasNodeMethod
Managed object
BSC
Multiplicity
1
Table 280
DN9813866
CS MSC State (Cont.)
CS NAS Node Method
Id:0900d8058089b05f
Confidential
413
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Description
This parameter determines the CS NAS Node Method to
be used in the BSC when Multipoint A is in use.
Additional information
-
Range
Done with Circuit Group Load (0), Done with WeightedRound-Robin (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Done with Circuit Group Load ==> 0
Done with Weighted-Round-Robin ==> 1
Default value
-
Default value notes
0
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
- The operator must check CS Weight Factor values for
each MSC/MSS beforehand changing value from 0 to 1.
Related parameters
csWeightFactor of BSC - When CS NAS Node Method is
changed from 0 (default value) to 1, all weight factors
values shall be defined
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94)
Related features
•
•
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I, E7M
MML Abbreviated Name
NASMETHOD
MML Full Name
CS NAS node method
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 280
9.88
CS NRI length (LENGTH)
Parameter name
CS NRI Length
Abbreviated name
csNriLength
Table 281
414
CS NAS Node Method (Cont.)
CS NRI Length
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Managed object
BSC
Multiplicity
1
Description
This parameter determines the length of the used NRI.
The given value indicates how many bits starting from bit
23 in TMSI are used for NRI. If the value is zero, Multipoint A is not in use.
NOTE: Restrictions:
CS NRI List must be defined before the CS NRI Length
parameter is changed to other than 0 (default value).
BSC makes the following checks:
CS NRI List must include valid NRI value or values per
Signalling Point Code until CS NRI Length can be
changed to other than 0 (default value). When CS NRI
Length is changed from 0 (default value), none of the NRI
values (NRI List 1, NRI List 2, NRI List 3, NRI List 4, NRI
List 5, NRI List 6, NRI List 7, NRI List 8, NRI List 9, NRI
List 10) must not exceed the decimal value range which
CS NRI Length is indicates.
For example:
If CS NRI Length has value 3, it means that 3 bits in TMSI
are used for NRI and with 3 bits ('111') it is possible to
have maximum value 7 in decimal. Therefore, none of the
NRI values (NRI List 1, NRI List 2, NRI List 3, NRI List 4,
NRI List 5, NRI List 6, NRI List 7, NRI List 8, NRI List 9,
NRI List 10) must not exceed value 7.
Additional information
-
Range
0...10
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriList of BSC - CS NRI List must be defined before the
CS NRI Length parameter is changed to other than 0
(default value).
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94)
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
Table 281
DN9813866
CS NRI Length (Cont.)
Id:0900d8058089b05f
Confidential
415
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
•
References
3GPP Reference: 23.236
MML Commands
E7I, E7M
MML Abbreviated Name
LENGTH
MML Full Name
CS NRI length
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 281
9.89
CS NRI list (-)
Parameter name
CS NRI List
Abbreviated name
csNriList
Managed object
BSC
Multiplicity
16
Table 282
416
CS NRI Length (Cont.)
CS NRI List
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Description
Base Station Controller (BSC) radio network object parameters
This parameter maps Network Resource Identifier(s) (NRI) to MSC's SPC and Global Core
Network Idenfication (CN-ID) to MSC's SPC. A
maximum of 11 NRIs can be mapped to one MSC.
Each NRI identifies uniquely the address of MSC
and its specific SPC.
This parameter maps also cells of PLMN area(s) to
MSC's SPC. A maximum of 16 PLMN areas can be
mapped to one MSC. Each PLMN code identifies
uniquely cells of a radio network.
There is maximum 16 MSC's information in this
parameter list.
NOTE: Restrictions/Instructions:
Only one Default Signalling Point Code parameter
can have value TRUE at a same time in CS NRI List
(others must be set as FALSE).
If CS NRI List parameter is added/modified from
NetAct (using Plan download or SendToNW) then
the subsequent upload might show differences for
this parameter.
BSC makes the following checks:
- There must always be one Default Signalling Point
Code -field having value TRUE in CS NRI List.
- There must not be two same Signalling Point
Code values in CS NR List
- There must not be two same Global CN-Id (consists of CN-ID+ MCC + MNC values) values in CS
NRI List
- There must be real MSC's SPC created on A Interface until it can be added to the CS NRI LIST and
downloaded to the BSC. This is instructed in Multipoint A FAI (Feature Activation Instructions)
customer document.
Additional information
Table 282
DN9813866
-
CS NRI List (Cont.)
Id:0900d8058089b05f
Confidential
417
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
• cnId
• csMSCState
• csNasNodeMethod
• csNullNri
• csWeightFactor
• defaultSignallingPointCode
• mcc
• mnc
• nriList1
• nriList10
• nriList2
• nriList3
• nriList4
• nriList5
• nriList6
• nriList7
• nriList8
• nriList9
• rnwMCC1
• rnwMCC10
• rnwMCC11
• rnwMCC12
• rnwMCC13
• rnwMCC14
• rnwMCC15
• rnwMCC16
• rnwMCC2
• rnwMCC3
• rnwMCC4
• rnwMCC5
• rnwMCC6
• rnwMCC7
• rnwMCC8
• rnwMCC9
• rnwMNC1
• rnwMNC10
• rnwMNC11
• rnwMNC12
• rnwMNC13
• rnwMNC14
• rnwMNC15
• rnwMNC16
• rnwMNC2
• rnwMNC3
• rnwMNC4
• rnwMNC5
• rnwMNC6
• rnwMNC7
Id:0900d8058089b05f
• rnwMNC8
Confidential
• rnwMNC9
• signallingPointCode
Child parameters
418
DN9813866
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
-
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - CS NRI List must be defined
before CS NRI Length parameter is changed to
other than value 0.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94)
Feature dependencies
•
•
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I, E7A, E7M, E7D
MML Abbreviated Name
-
MML Full Name
CS NRI list
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 282
9.90
CS NRI List (Cont.)
CS TCH allocation calculation (CTC)
Parameter name
CS TCH Allocation Calculation
Abbreviated name
gprsTerritoryCalc
Managed object
BSC
Multiplicity
1
Table 283
DN9813866
Base Station Controller (BSC) radio network object parameters
CS TCH Allocation Calculation
Id:0900d8058089b05f
Confidential
419
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define how the GPRS territory is
seen when calculating FR resources. (The RTSLs to be
used when the limit for FR resources is defined for the
TCH rate selection between full rate and half rate).
Note:
MML Range:
0 = Only CSW used RTSLs are used to calculate
resources.
1 = CSW and PSW used RTSLs are used. PSW used
RTSLs are seen as occupied resource when calculating
PSW RTSLs.
2 = CSW used and PSW used RTSLs are used. PSW
used RTSLs are seen as idle resource when calculating
resources.
Additional information
-
Range
Only CSW used RTSLs are used (0), CSW and PSW
used RTSLs are used. (1), CSW used and PSW used
RTSLs are used. (2)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Only CSW used RTSLs are used ==> 0
CSW and PSW used RTSLs are used. ==> 1
CSW used and PSW used RTSLs are used. ==> 2
Default value
Only CSW used RTSLs are used (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) AND ( AMR HR (72) (optional) OR
Half Rate (17) (optional) ) OR Enhanced GPRS
(EGPRS) Usage (51) (optional) AND ( AMR HR (72)
(optional) OR Half Rate (17) (optional) )
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
CTC
Table 283
420
•
CS TCH Allocation Calculation (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Full Name
CS TCH allocation calculation
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 283
9.91
CS TCH Allocation Calculation (Cont.)
CS TCH allocation RTSL0 (CTR)
Parameter name
CS TCH Allocation RTSL0
Abbreviated name
rtsl0PrefInTCHAlloc
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the priority order between
GPRS and RTSL-0 allocation. With the parameter the
RTSL-0 can be defined to be allocating before allocating
a TCH from GPRS territory (the order of preference in
TCH allocation between the RTSL-0 hopping group and
the GPRS territory of the BB-hopping BTSs).
Note:
MML range:
Y = The RTSL-0 hopping group is allocated first. If no free
resources are available then the GPRS territory is
searched.
N = The GPRS territory is allocated first. If no free
resources are available then the RTSL-0 hopping group
is searched.
Default: N
Additional information
-
Range
The GPRS territory is allocated first (N) (0), The RTSL-0
hopping group is allocated first (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
The GPRS territory is allocated first (N) ==> 0
The RTSL-0 hopping group is allocated first (Y) ==> 1
Default value
The GPRS territory is allocated first (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Table 284
DN9813866
CS TCH Allocation RTSL0
Id:0900d8058089b05f
Confidential
421
Base Station Controller (BSC) radio network object parameters
Parameter relationships
Related options
Related features
BSS Radio Network Parameter Dictionary
-
•
-
•
•
Interfaces
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
CTR
MML Full Name
CS TCH allocation RTSL0
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 284
9.92
CS TCH Allocation RTSL0 (Cont.)
CS Weight Factor (WEIGHT)
Parameter name
CS Weight Factor
Abbreviated name
csWeightFactor
Managed object
BSC
Multiplicity
1
Description
With this parameter you define CS Weight Factor
value per MSC/MSS for round-robin selection
NAS Node method to be used in the BSC when
Multipoint A is in use.
Note: Only supported in local MML
Additional information
-
Range
0...100
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
255
Default value notes
-
Required on Creation
mandatory
Special value
Not used (255)
Related functions
-
Table 285
422
CS Weight Factor
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Modification
On-Line
Modified
- The operator must check CS Weight Factor values
for each MSC/MSS beforehand changing BSC CS
NAS Node Method value from 0 to 1.
Related parameters
csNasNodeMethod of BSC - When CS NAS Node
Method is changed from 0 (default value) to 1, all
weight factors values shall be defined
Parameter relationships
Related options
•
Multipoint A Interface for BSC (94)
Feature dependencies
•
•
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I, E7M
MML Abbreviated Name
WEIGHT
MML Full Name
CS Weight Factor
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 285
9.93
CS Weight Factor (Cont.)
C-plane packet drop period (CPLPDP)
Parameter name
C-plane Packet Drop Period
Abbreviated name
cPlanePacketDropPeriod
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter user defined the packet drop
period for C-plane packets.
NOTE: Parameter is valid only for Flexi EDGE and
Flexi Multiradio site types.
Additional information
-
Range
0...10000
Step
10
Table 286
DN9813866
C-plane Packet Drop Period
Id:0900d8058089b05f
Confidential
423
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Units
ms
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
CPLPDP
MML Commands
EEY, EEO
MML Full Name
C-plane packet drop period
Segment Level Parameter
-
Table 286
9.94
CS packet drop period (CSPDP)
Parameter name
CS Packet Drop Period
Abbreviated name
csPacketDropPeriod
3GPP name
-
Managed Object
BSC
Multiplicity
1
Table 287
424
C-plane Packet Drop Period (Cont.)
CS Packet Drop Period
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
With this parameter user defined the packet drop
period for CS packets.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
0...100
Step
1
Units
ms
Formula for getting
internal value
internal_value =gui_value
Default value
25
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
CSPDP
MML Commands
EEY, EEO
MML Full Name
CS packet drop period
Segment Level Parameter
-
Table 287
DN9813866
CS Packet Drop Period (Cont.)
Id:0900d8058089b05f
Confidential
425
Base Station Controller (BSC) radio network object parameters
9.95
BSS Radio Network Parameter Dictionary
CS UDP-MUX port (CSUMP)
Parameter name
CS UDP-MUX Port
Abbreviated name
csUdpMuxPort
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you identify the Packet Abis
user datagram protocol (UDP) MUX port number
for CS U-plane.
The configured value for "CsUDP-MuxPort" shall
be different from the one configured for "PsUDPMuxPort" and from all other UDP ports reserved for
e.g. Traceroute.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
-
Range
49152...65534
Step
2
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
49152
Default value notes
-
Special value
Not defined (65535)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
Parameter is updated to functioning in certain BCF
of the BSC when BCF is next time reset after
parameter modification. When modified by FBPP
updating to BCF is made to all BCFs of the BSC.
Related parameters
psUdpMuxPort of BSC - This parameter value has
to be defined different than CS UDP-MUX Port.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Table 288
426
CS UDP-MUX Port
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
CSUMP
MML Commands
EEY, EEO
MML Full Name
CS UDP-MUX port
Segment Level Parameter
-
Table 288
9.96
CS UDP-MUX Port (Cont.)
clock-sync to DSCP Mapping (CLKS)
Parameter name
Clock-sync to DSCP Mapping
Abbreviated name
tmClockSync
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define Clock-sync to DSCP
mapping.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
NOTE:
In case clock synchronization is provided through a
PWE solution, then Clock-Sync to DSCP mapping
is achieved via the already existing means for the
PWE feature.
Additional information
-
Range
BE (000000) (0),
AF11 (001010) (10),
AF21 (010010) (18),
AF31 (011010) (26),
AF41 (100010) (34),
EF (101110) (46)
Table 289
DN9813866
Clock-sync to DSCP Mapping
Id:0900d8058089b05f
Confidential
427
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
BE
(000000) ==> 0
AF11 (001010) ==> 10
AF21 (010010) ==> 18
AF31 (011010) ==> 26
AF41 (100010) ==> 34
EF
(101110) ==> 46
Default value
EF (101110) (46)
Default value notes
EF
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21454: Packet Abis over IP/Eth
BSS21440: Packet Abis over TDM
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
NSN reference: BSS21440 - Packet Abis over TDM
StandardNSN reference: BSS21454 - Packet Abis
over IP/Eth
File based provisioning
supported
true
MML Abbreviated Name
CLKS
MML Commands
EEY, EEO
MML Full Name
clock-sync to DSCP Mapping
Segment Level Parameter
-
Table 289
428
Clock-sync to DSCP Mapping (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.97
Base Station Controller (BSC) radio network object parameters
DCS macrocell threshold (DMAC)
Parameter name
DCS Macrocell Threshold
Abbreviated name
dcsMacrocellThreshold
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the macrocell size
by means of the maximum transmission power of
the MS in a GSM 1800 or GSM 1900 cell. If you set
the parameter value at 0 dBm, the division of cells
into macrocells and microcells is not in use.
NOTE: MML value range:
GSM 1800: 0...36(dBm), with 2 dBm step
GSM 1900: 0...32(dBm), with 2 dBm step, and 33
(dBm)
NOTE: NetAct internal value range:
GSM 1800:
0..30 dBm: 0..15 (UI value - 30)/-2
32 dBm: 31
34 dBm: 30
36 dBm: 29
GSM 1900:
0..30 dBm: 0..15 (UI value - 30)/-2
32 dBm: 31
33 dBm: 30
Additional information
-
Range
0...36
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
26
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Table 290
DN9813866
DCS Macrocell Threshold
Id:0900d8058089b05f
Confidential
429
Base Station Controller (BSC) radio network object parameters
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
DMAC
MML Full Name
DCS macrocell threshold
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 290
9.98
BSS Radio Network Parameter Dictionary
RAC <-> RACApp
RAC <-> BSC
DCS Macrocell Threshold (Cont.)
DCS microcell threshold (DMIC)
Parameter name
DCS Microcell Threshold
Abbreviated name
dcsMicrocellThreshold
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the microcell size by
means of the maximum transmission power of the MS in
a GSM 1800 or GSM 1900 cell. If you set the parameter
value at 33 dBm (GSM 1800) or 36 dBm (GSM 1900), the
division of cells into macrocells and microcells is not in
use.
NOTE: MML value range:
GSM 1800: 0...36(dBm), with 2 dBm step
GSM 1900: 0...32(dBm), with 2 dBm step, and 33 (dBm)
NOTE: NetAct internal value range:
GSM 1800:
0..30 dBm: 0..15 (UI value - 30)/-2
32 dBm: 31
34 dBm: 30
36 dBm: 29
GSM 1900:
0..30 dBm: 0..15 (UI value - 30)/-2
32 dBm: 31
33 dBm: 30
Table 291
430
DCS Microcell Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Additional information
-
Range
0...36
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
24
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
DMIC
MML Full Name
DCS microcell threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 291
9.99
DCS Microcell Threshold (Cont.)
default SPC (DEF_SPC)
Parameter name
Default Signalling Point Code
Abbreviated name
defaultSignallingPointCode
Managed object
BSC
Multiplicity
1
Description
With this parameter you define if Signalling Point Code is
set as default.
NOTE:
Only one Default Signalling Point Code -field can have
value TRUE at the same time in CS NRI List (others shall
be set as FALSE).
Table 292
DN9813866
Default Signalling Point Code
Id:0900d8058089b05f
Confidential
431
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Additional information
-
Range
false (0), true (1)
Step
-
Unit
-
Formula for getting internal
value
•
•
false => 0
true => 1
Default value
false (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
E7M
MML Abbreviated Name
DEF_SPC
MML Full Name
default SPC
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 292
9.100
delay of HO and PC for emergency calls (DEC)
Parameter name
Delay Of HO And PC For Emergency Calls
Abbreviated name
delayHoPcEmergencyCalls
Managed object
BSC
Multiplicity
1
Description
With this parameter you can temporarily disable mobile
power control and handovers in TCH for emergency calls.
This enhances U-TDOA positioning accuracy.
Additional information
-
Range
0...16
Table 293
432
Default Signalling Point Code (Cont.)
Delay Of HO And PC For Emergency Calls
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
5s
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS20211: Disabling PC and HO for E911/UTDOA
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
DEC
MML Full Name
delay of HO and PC for emergency calls
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 293
9.101
DFCA channel allocation method (DCAM)
Parameter name
DFCA Channel Allocation Method
Abbreviated name
dfcaChannelAllocMethod
Managed object
BSC
Multiplicity
1
Table 294
DN9813866
Delay Of HO And PC For Emergency Calls (Cont.)
DFCA Channel Allocation Method
Id:0900d8058089b05f
Confidential
433
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define if DCFA assignments are made primarily to channels with the connection specific C/I target level or to channels with
the highest positive C/I difference from the target
level.
Note:
MML range:
0 (primary target of a DFCA assignment is a MA,
MAIO and tsl combination with the highest C/I difference from the target level)
1 (primary target of a DFCA assignment is a MA,
MAIO and tsl combination on the connection
specific target C/I level)
Additional information
-
Range
TCH With Highest C/I Level (0), TCH With C/I On
Target Level (1)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
TCH With Highest C/I Level ==> 0
TCH With C/I On Target Level ==> 1
Default value
TCH With Highest C/I Level (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70)
Feature dependencies
•
BSS11052: Dynamic Frequency and Channel
Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
DCAM
Table 294
434
DFCA Channel Allocation Method (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
MML Full Name
DFCA channel allocation method
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 294
9.102
Base Station Controller (BSC) radio network object parameters
DFCA Channel Allocation Method (Cont.)
disable external DR (DEXDR)
Parameter name
Disable External DR
Abbreviated name
disableExtDr
Managed object
BSC
Multiplicity
1
Description
With this parameter you disable or enable the external
directed retry handovers.
Additional information
-
Range
enable external directed retry handovers (N) (0), disable
external directed retry handovers (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
enable external directed retry handovers (N) ==> 0
disable external directed retry handovers (Y) ==> 1
Default value
enable external directed retry handovers (N) (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
DEXDR
Table 295
DN9813866
RAC <-> RACApp
RAC <-> BSC
Disable External DR
Id:0900d8058089b05f
Confidential
435
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Full Name
disable external DR
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 295
9.103
Disable External DR (Cont.)
disable internal HO (DINHO)
Parameter name
Disable Internal HO
Abbreviated name
disableIntHo
Managed object
BSC
Multiplicity
1
Description
With this parameter you define whether all handovers are
controlled by the MSC or not.Note it is also possible
define for each segment separately that are the handovers of the segment controlled by MSC or not by using
‘MSC HO Control Enabled’ segment parameter. When
the segment level parameter is used, the Disable Internal
HO parameter value doesn’t apply for that segment.
Additional information
-
Range
all handovers are not controlled by the MSC (N) (0), all
handovers are controlled by the MSC (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
all handovers are not controlled by the MSC (N) ==> 0
all handovers are controlled by the MSC (Y) ==> 1
Default value
all handovers are not controlled by the MSC (N) (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
mscHoCoEn of BTS - Value of the 'MSC HO Control
Enabled' segment parameter overrules value of 'Disable
Internal HO' BSC parameter, if the 'MSC HO Control
Enabled' parameter has value which differs from 'Not
Defined
Parameter relationships
-
Related options
-
Related features
-
Table 296
436
Disable Internal HO
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
DINHO
MML Full Name
disable internal HO
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 296
9.104
DL PC 8PSK BEP target (PCPSK)
Parameter name
DL PC 8PSK BEP Target
Abbreviated name
dlPc8PskBepTarget
Managed object
BSC
Multiplicity
1
Description
With this parameter user is able to define the target 8PSK BEP value for EGPRS TBFs. The decision to
increase or decrease the DL power level is done against
this parameter.
Additional information
-
Range
0... 31
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
29
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
When changed PCU starts to do DL power control for
EGPRS TBFs with respect to this target value.
Related parameters
-
Parameter relationships
-
Related options
(E)GPRS DL Power Control (164)
Related features
RG301666 (E)GPRS DL Power Control
Table 297
DN9813866
Disable Internal HO (Cont.)
DL PC 8PSK BEP Target
Id:0900d8058089b05f
Confidential
437
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
•
•
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
RG301666 (E)GPRS DL Power Control
MML Commands
EEM, EEO
MML Abbreviated Name
PCPSK
MML Full Name
DL PC 8PSK BEP target
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 297
9.105
DL PC C/I target (PCCI)
Parameter name
DL PC C/I Target
Abbreviated name
dlPcCiTarget
Managed object
BSC
Multiplicity
1
Description
With this parameter user is able to define the target C/I
value for GPRS TBFs. The decision to increase or
decrease the DL power level is done against this parameter.
Additional information
-
Range
0... 30
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
15
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
When changed PCU starts to do DL power control for
EGPRS TBFs with respect to this target value.
Related parameters
-
Parameter relationships
-
Related options
Progressive Power Control for (E)GPRS (164)
Related features
RG301666 (E)GPRS DL Power Control
Table 298
438
DL PC 8PSK BEP Target (Cont.)
DL PC C/I Target
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
•
•
Interfaces
BSC <-> RAC
RAC <-> RACApp
References
RG301666 (E)GPRS DL Power Control
MML Commands
EEM, EEO
MML Abbreviated Name
PCCI
MML Full Name
DL PC C/I target
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 298
9.106
DL PC C/I Target (Cont.)
DL high priority SSS (DHP)
Parameter name
DL High Priority SSS
Abbreviated name
schedStepSizeDlHighPrior
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the scheduling step side
(SSS) for high priority level in the downlink direction.
Additional information
-
Range
1...12
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
3
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
Interfaces
Table 299
DN9813866
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
•
•
RACApp <-> RAC
RAC <-> BSC
DL High Priority SSS
Id:0900d8058089b05f
Confidential
439
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
References
-
MML Commands
EEV, EEO
MML Abbreviated Name
DHP
MML Full Name
DL high priority SSS
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 299
9.107
DL High Priority SSS (Cont.)
DL low priority SSS (DLP)
Parameter name
DL Low Priority SSS
Abbreviated name
schedStepSizeDlLowPrior
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the scheduling step side
(SSS) for low priority level in the downlink direction.
Additional information
-
Range
1...12
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
12
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
•
•
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEV, EEO
Table 300
440
•
DL Low Priority SSS
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Abbreviated Name
DLP
MML Full Name
DL low priority SSS
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 300
9.108
DL Low Priority SSS (Cont.)
DL normal priority SSS (DNP)
Parameter name
DL Normal Priority SSS
Abbreviated name
schedStepSizeDlNormPrior
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the scheduling step side
(SSS) for normal priority level in the downlink direction.
Additional information
-
Range
1...12
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
6
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39)
-
•
•
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEV, EEO
MML Abbreviated Name
DNP
MML Full Name
DL normal priority SSS
Table 301
DN9813866
•
DL Normal Priority SSS
Id:0900d8058089b05f
Confidential
441
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
BSS Radio Network Parameter Dictionary
-
File Based Provisioning sup- true
ported
Table 301
9.109
DL Normal Priority SSS (Cont.)
DLDC offset for PCU2-E Selection (DOP)
Parameter name
DLDC offset for PCU2-E selection
Abbreviated name
dldcOffsefPcu2e
Managed object
BSC
Multiplicity
1
Description
With this parameter you can change the behavior of the
PCU selection algorithm in cases when DLDC is in use
and in the same pool there are both PCU2-E and PCU2D/U type cards.
The bigger this parameter value is then it means that
PCU2-E card can have more capacity used than other
PCU2 cards.
If PCU2-E cards are not wanted to be preferred in the
selection this parameter must have value 0.
Additional information
-
Range
0...80
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
optional
Special value
PCU2-E cards are not preferred. (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
pcuSelectionThresh of BSC - In the target PCU calculation this value in increased by the DLDC offset for PCU2
selection parameter value. If the calculated value is more
than PSAT max value then PSAT max value is used in
the calculation , pseOverlAlarmThresh of BSC - In the
alarm setting/cancelling this value is increased by the
DLDC offset for PCU2 selection parameter value.
Meaning that if the parameter value is higher than 0 then
the alarm limit is higher for the PCU2-E than other PCU2
types.
Table 302
442
DLDC offset for PCU2-E selection
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Parameter relationships
-
Related options
•
Downlink Dual Carrier (141) (optional) AND Packet
Control Unit (PCU2) pooling (97) (optional)
Related features
•
•
BSS21228: Downlink Dual Carrier
BSS20106: Packet Control Unit (PCU2) pooling
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
DOP
MML Full Name
DLDC offset for PCU2-E Selection
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 302
9.110
DTM fragmentation penalty (DFP)
Parameter name
DTM Fragmentation Penalty
Abbreviated name
dtmFragmentationPenalty
Managed object
BSC
Multiplicity
1
Table 303
DN9813866
DLDC offset for PCU2-E selection (Cont.)
DTM Fragmentation Penalty
Id:0900d8058089b05f
Confidential
443
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
This parameter defines the value of the fragmentation penalty that is used in the DTM channel allocation algorithm if there is a need to search for a
configuration giving the highest capacity for the
DTM MS. This is the case if the DTM MS is considered to be a nRT user and if there are some RT
and/or DTM allocations existing for other mobiles in
the territory.
That is, this parameter is used to balance the tradeoff between searching for a DTM allocation that
gives the optimal DTM-PS resources and searching
for a DTM allocation that avoids fragmentation of
PS resources in the PS territory.
The capacity of a DTM allocation is estimated in
terms of radio timeslots and the fragmentation
penalty is subtracted from the estimated capacity
value, if the DTM allocation would increase the fragmentation of the PS resources. That is the case
when the DTM-CS timeslot and its neighbouring
timeslots on both sides are originally in PS use.
In an example where a DTM-PS allocation consists
of two timeslots and the DTM MS gets a 50 % share
on the first timeslot and a 100 % share on the
second timeslot and the fragmentation penalty has
a value of 0.5. The capacity of that DTM allocation
is 1.5 (=0.5 + 1.0) timeslots if the DTM allocation
does not increase the fragmentation and it is 1.0
(=0.5 + 1.0 - 0.5) if the DTM allocation increases the
fragmentation.
The DTM fragmentation penalty value of 0 means
that a DTM allocation that increases the fragmentation of PS resources is as good a choice as a DTM
allocation that does not increase the fragmentation
of PS resources.
The DTM fragmentation penalty value of 1 means
that a DTM allocation that does not increase the
fragmentation of PS resources is selected instead
of a DTM allocation that increases the fragmentation of PS resources unless the latter one provides
one timeslot more capacity than the former one in
which case the latter one is selected.
Additional information
-
Range
0...1
Step
0.1
Unit
-
Table 303
444
DTM Fragmentation Penalty (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
internal_value = gui_value * 10
Default value
0.3
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Dual Transfer Mode and Statistics (DTM) (91)
(optional) AND ( BSC GPRS Param Enabled
(GPRS O&M in BSC) (39) (optional) OR
Enhanced GPRS (EGPRS) Usage (51)
(optional) )
Feature dependencies
•
BSS20088: Dual Transfer Mode (DTM)
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
DFP
MML Full Name
DTM fragmentation penalty
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 303
9.111
DTM Fragmentation Penalty (Cont.)
DTRX power down supervision period (PWDPRD)
Parameter name
DTRX Power Down Supervision Period
Abbreviated name
dtrxPowerDownSupervisionPeriod
Managed object
BSC
Multiplicity
1
Table 304
DN9813866
Base Station Controller (BSC) radio network object parameters
DTRX Power Down Supervision Period
Id:0900d8058089b05f
Confidential
445
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Description
When the traffic load in a segment falls lower than
defined by DTRX Power Down Threshold the load is
followed for a period of time defined by the DTRX Power
Down Supervision Period parameter. The actual TRX
power down is started if the load remains lower than
defined by DTRX Power Down Threshold parameter for
the whole supervision period.
Additional information
-
Range
5...60
Step
1
Unit
minutes
Formula for getting internal
value
internal_value = gui_value * 60
Default value
10 minutes
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
dtrxPowerDownThreshold of BTS - TRX power down is
started if the load remains lower than defined by DTRX
Power Down Threshold parameter for the whole DTRX
Power Down Supervision Period.
Parameter relationships
-
Related options
•
FlexiEDGE Dual TRX Automatic Power Down (140)
Related features
•
BSS20984: FlexiEDGE Dual TRX Automatic Power
Down
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
PWDPRD
MML Full Name
DTRX power down supervision period
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 304
9.112
DTRX Power Down Supervision Period (Cont.)
EGPRS inactivity criteria (EGIC)
Parameter name
Table 305
446
EGPRS Inactivity Criteria
EGPRS Inactivity Criteria
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Abbreviated name
inactCriteria
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the criteria used to the
EGPRS Inactivity.
Additional information
-
Range
Alarm disabled (0), No normal UL TBF releases (1), No
normal DL TBF releases (2), No normal UL and DL TBF
releases (3)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Alarm disabled ==> 0
No normal UL TBF releases ==> 1
No normal DL TBF releases ==> 2
No normal UL and DL TBF releases ==> 3
Default value
Alarm disabled (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20071: PCU Performance Optimization
BSS20062: (E)GPRS Inactivity Alarm / DX-part
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
EGIC
MML Full Name
EGPRS inactivity criteria
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 305
DN9813866
EGPRS Inactivity Criteria (Cont.)
Id:0900d8058089b05f
Confidential
447
Base Station Controller (BSC) radio network object parameters
9.113
BSS Radio Network Parameter Dictionary
enable answer to paging call on FACCH (EPF)
Parameter name
Enable Answer To Paging Call On FACCH
Abbreviated name
pagingAnsOnFacch
Managed object
BSC
Multiplicity
1
Description
With this parameter you enable or disable an answer to
the paging call setup on FACCH. FACCH call setup is
only possible when SDCCH congestion occurs.
Additional information
-
Range
disable answer to paging call setup on FACCH (N) (0),
enable answer to paging call setup on FACCH (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
disable answer to paging call setup on FACCH (N) ==> 0
enable answer to paging call setup on FACCH (Y) ==> 1
Default value
disable answer to paging call setup on FACCH (N) (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
-
•
•
Interfaces
FACCH Call Setup Due To SDCCH Congestion (4)
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
EPF
MML Full Name
enable answer to paging call on FACCH
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 306
448
Enable Answer To Paging Call On FACCH
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.114
Base Station Controller (BSC) radio network object parameters
enable call re-establishment on FACCH (ERF)
Parameter name
Enable Call Re-Establishment On FACCH
Abbreviated name
reestablishOnFacch
Managed object
BSC
Multiplicity
1
Description
With this parameter you enable or disable the call reestablishment setup on FACCH. FACCH call setup is
only possible when SDCCCH congestion occurs.
NOTE:
Call re-establishment setup on FACCH is only possible in
those cells in which call re-establishment is allowed (the
EQF command, parameter RE.) You can set the FACCH
call setup feature ON or OFF in PRFILE.
Additional information
-
Range
disable call re-establishment setup on FACCH (N) (0),
enable call re-establishment setup on FACCH (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
disable call re-establishment setup on FACCH (N) ==> 0
enable call re-establishment setup on FACCH (Y) ==> 1
Default value
disable call re-establishment setup on FACCH (N) (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
ERF
MML Full Name
enable call re-establishment on FACCH
Segment Level Parameter
-
Table 307
DN9813866
FACCH Call Setup Due To SDCCH Congestion (4)
Enable Call Re-Establishment On FACCH
Id:0900d8058089b05f
Confidential
449
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 307
9.115
Enable Call Re-Establishment On FACCH (Cont.)
enable emergency call on FACCH (EEF)
Parameter name
Enable Emergency Call On FACCH
Abbreviated name
emerCallOnFacch
Managed object
BSC
Multiplicity
1
Description
With this parameter you enable or disable the emergency call setup on FACCH.
Note:
Emergency call setup on FACCH is only possible in
those cells in which emergency calls are not
restricted (the EQF command, parameter EC).
FACCH call setup is only possible when SDCCH
congestion occurs.
Additional information
-
Range
disable emergency call setup on FACCH (N) (0),
enable emergency call setup on FACCH (Y) (1)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
disable emergency call setup on FACCH (N) ==> 0
enable emergency call setup on FACCH (Y) ==> 1
Default value
disable emergency call setup on FACCH (N) (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
Table 308
450
RAC <-> RACApp
RAC <-> BSC
Enable Emergency Call On FACCH
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
EEF
MML Full Name
enable emergency call on FACCH
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 308
9.116
Base Station Controller (BSC) radio network object parameters
Enable Emergency Call On FACCH (Cont.)
enable ordinary calls on FACCH (EOF)
Parameter name
Enable Ordinary Calls On FACCH
Abbreviated name
ordinaryCallOnFacch
Managed object
BSC
Multiplicity
1
Description
With this parameter you enable or disable the ordinary
call setup on FACCH. FACCH call setup is only possible
when SDCCH congestion occurs.
Additional information
-
Range
disable ordinary calls setup on FACCH (N) (0), enable
ordinary calls setup on FACCH (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
disable ordinary calls setup on FACCH (N) ==> 0
enable ordinary calls setup on FACCH (Y) ==> 1
Default value
disable ordinary calls setup on FACCH (N) (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
Table 309
DN9813866
•
FACCH Call Setup Due To SDCCH Congestion (4)
-
Enable Ordinary Calls On FACCH
Id:0900d8058089b05f
Confidential
451
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
EOF
MML Full Name
enable ordinary calls on FACCH
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 309
9.117
Enable Ordinary Calls On FACCH (Cont.)
ending moment for supervision of BTS (EMBNT)
Parameter name
BTS Supervision Stopping Time Hour
Abbreviated name
nokBtsOffHour
Managed object
BSC
Multiplicity
1
Description
Attribute indicates the hour on which the control of BTSs
with no transaction ends.
MML NOTE:
In MML only one parameter:
ending moment for supervision of BTS
Range: 00-00 .. 23-59
Default: 18-00
Additional information
-
Range
0...23
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
18
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Table 310
452
BTS Supervision Stopping Time Hour
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
EMBNT
MML Full Name
ending moment for supervision of BTS
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 310
9.118
BTS Supervision Stopping Time Hour (Cont.)
ending moment for supervision of BTS (EMBNT)
Parameter name
BTS Supervision Stopping Time Minute
Abbreviated name
nokBtsOffMinute
Managed object
BSC
Multiplicity
1
Description
Attribute indicates the minute on which the control of
BTSs with no transaction ends.
MML NOTE:
In MML only one parameter:
ending moment for supervision of BTS
Range: 00-00 .. 23-59
Default: 18-00
Additional information
-
Range
0...59
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 311
DN9813866
BTS Supervision Stopping Time Minute
Id:0900d8058089b05f
Confidential
453
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
EMBNT
MML Full Name
ending moment for supervision of BTS
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 311
9.119
BTS Supervision Stopping Time Minute (Cont.)
events per hour for EGPRS inactivity alarm (IEPH)
Parameter name
Events Per Hour For EGPRS Inactivity Alarm
Abbreviated name
inactEventsPerHour
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the number of TBF allocation attempts required per hour for EGPRS Inactivity
Alarm.
Additional information
-
Range
0...255
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
10
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Table 312
454
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Events Per Hour For EGPRS Inactivity Alarm
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related features
•
•
BSS20071: PCU Performance Optimization
BSS20062: (E)GPRS Inactivity Alarm / DX-part
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
IEPH
MML Full Name
events per hour for EGPRS inactivity alarm
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 312
9.120
Events Per Hour For EGPRS Inactivity Alarm (Cont.)
Expected BSC-BSC interface delay (EBID)
Parameter name
Expected BSC-BSC Interface Delay
Abbreviated name
expectedBscBscInterfaceDelay
Managed object
BSC
Multiplicity
1
Description
This parameter is used in the Radio Resource Manager
for the channel assignment control to prevent simultaneous channel allocations in neighbouring BSCs.
Additional information
-
Range
0...2000
Step
10
Unit
ms
Formula for getting internal
value
internal_value = gui_value / 10
Default value
50 ms
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Table 313
DN9813866
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Expected BSC-BSC Interface Delay
Id:0900d8058089b05f
Confidential
455
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
EBID
MML Full Name
Expected BSC-BSC interface delay
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 313
9.121
Expected BSC-BSC Interface Delay (Cont.)
FEP in PC HO use (FPHO)
Parameter name
FEP In PC HO Use
Abbreviated name
fepInPcHoUse
Managed object
BSC
Multiplicity
1
Description
With this parameter you can indicate whether the Frame
Error Probability based Power Control (PC) and
Handover (HO) decision-making is used in the Power
control and Handover algorithm.
Additional information
-
Range
PC and HO decision-making is not used (N) (0), PC and
HO decision-making is used (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
PC and HO decision-making is not used (N) ==> 0
PC and HO decision-making is used (Y) ==> 1
Default value
PC and HO decision-making is not used (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 314
456
FEP In PC HO Use
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
•
Related options
Related features
FER Measurement (44)
-
•
•
Interfaces
RACApp <-> RAC
BSC <-> RAC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
FPHO
MML Full Name
FEP in PC HO use
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 314
9.122
FEP In PC HO Use (Cont.)
Forced Mode (FCDMODE)
Parameter name
CS Forced Mode
Abbreviated name
csForcedMode
Managed object
BSC
Multiplicity
1
Description
This parameter determines whether NAS Node method is
used for all traffic in the BSC when Multipoint A is in use.
Additional information
-
Range
normal NRI based traffic routing (0), NAS Node function
is used for all traffic (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
normal NRI based traffic routing ==> 0
NAS Node function is used for all traffic ==> 1
Default value
-
Default value notes
0
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Table 315
DN9813866
CS Forced Mode
Id:0900d8058089b05f
Confidential
457
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related features
•
•
BSS21217: Multipoint A Load Balancing (standard)
BSS20092: Multipoint A Interface for BSC (standard)
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I, E7M
MML Abbreviated Name
FCDMODE
MML Full Name
Forced Mode
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 315
9.123
CS Forced Mode (Cont.)
forced release priority threshold (FRPT)
Parameter name
Forced Release Priority Threshold
Abbreviated name
fcdRelPriThres
Managed object
BSC
Multiplicity
1
Description
This parameter defines the priority levels of subscribers to which the Forced release after unsuccessful forced handover attempt is applied.
The value of this parameter defines the highest
value of priority levels which are included in subscriber class 2.
With this parameter it is possible to divide subscribers to different classes according to their preemption capabilities:
Class 1: subscribers having priority level 1 are
capable of causing a forced release for subscribers
with lower priority.
Class 2: subscribers having priority level from 2 to
Forced release priority threshold are capable of
causing a forced handover as a primary option and
a forced release as a secondary option for lower
priority subscriber.
Class 3: Pre-emption-capable subscribers having
priority level lower than Forced release priority
threshold are capable of causing a forced handover
for a lower priority subscriber.
Additional information
Table 316
458
-
Forced Release Priority Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Range
1...14
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
1
Default value notes
Default value of the parameter is 1, meaning the
Forced release after unsuccessful forced handover
attempt -functionality is not applied to any preemption-capable subscribers and that the preemption-based subscriber classes are not defined.
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
By setting some other than the default value to the
parameter, it is possible to define three subscriber
classes. The value to be set depends on the priority
levels of the subscribers used in the network.
Related parameters
-
Parameter relationships
-
Related options
•
Preempt Usage In BSC (68) (optional) AND
Market Expansion Toolkit (110) (optional)
Feature dependencies
•
BSS20869: Enhancements on Priority Call and
Pre-emption in BSC
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
FRPT
MML Full Name
forced release priority threshold
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 316
DN9813866
Base Station Controller (BSC) radio network object parameters
Forced Release Priority Threshold (Cont.)
Id:0900d8058089b05f
Confidential
459
Base Station Controller (BSC) radio network object parameters
9.124
free TSL for CS downgrade (CSD)
Parameter name
Free TSL For CS Downgrade
Abbreviated name
freeTSLsCsDowngrade
Managed object
BSC
Multiplicity
1
Description
The parameter gives a target probability of TCH
availability for circuit switched services in a BTS
with GPRS territory. Based on the given probability
and the size of a BTS (number of TRXs) the BSC
defines a margin of idle TCHs that it tries to
maintain free for the incoming circuit switched TCH
requests in the BTS. If the number of idle TCHs in
the circuit switched territory of a BTS decreases
below the defined margin, a GPRS territory downgrade is started. In the margin definition the BSC
uses a table that is shown in "GPRS territory downgrade" of "GPRS in BSC".
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting
internal value
internal_value = gui_value
Default value
95 %
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Feature dependencies
-
Interfaces
•
•
References
-
Table 317
460
BSS Radio Network Parameter Dictionary
BSC GPRS Param Enabled (GPRS O&M in
BSC) (39) (optional) OR Enhanced GPRS
(EGPRS) Usage (51) (optional)
RACApp <-> RAC
BSC <-> RAC
Free TSL For CS Downgrade
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
MML Commands
EEM, EEO
MML Abbreviated Name
CSD
MML Full Name
free TSL for CS downgrade
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 317
9.125
Free TSL For CS Downgrade (Cont.)
Free TSLs For CS Upgrade (CSU)
Parameter name
Free TSLs For CS Upgrade
Abbreviated name
freeTSLsCsUpgrade
Managed object
BSC
Multiplicity
1
Description
With this parameter you define a period following a GPRS
upgrade during which the probability for a GPRS downgrade in a BTS should be no more than 5%. Based on the
given time and the size of a BTS (number of TRXs) the
BSC defines a margin of idle TSLs that is required as a
condition for starting a GPRS territory upgrade in the
BTS. A GPRS upgrade may be done if the number of free
TSLs in a BTS is at least equal to the defined margin still
after the upgrade. In the margin definition the BSC uses
a table that is shown in "GPRS territory upgrade" of
"GPRS in BSC".
Additional information
-
Range
0...10
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
4s
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 318
DN9813866
Base Station Controller (BSC) radio network object parameters
Free TSLs For CS Upgrade
Id:0900d8058089b05f
Confidential
461
Base Station Controller (BSC) radio network object parameters
Related options
Related features
BSS Radio Network Parameter Dictionary
•
-
•
•
Interfaces
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
RACApp <-> RAC
BSC <-> RAC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
CSU
MML Full Name
Free TSLs For CS Upgrade
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 318
9.126
GPRS territory update guard time (GTUGT)
Parameter name
GPRS Territory Update Guard Time
Abbreviated name
terrUpdGuardTGprs
Managed object
BSC
Multiplicity
1
Description
With this parameter you set the time which must elapse
between two subsequent territory updates.
Additional information
-
Range
1...255
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
5s
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 319
462
Free TSLs For CS Upgrade (Cont.)
GPRS Territory Update Guard Time
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
•
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
•
•
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
GTUGT
MML Full Name
GPRS territory update guard time
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 319
9.127
GSM Macrocell Threshold (GMAC)
Parameter name
GSM Macrocell Threshold
Abbreviated name
gsmMacrocellThreshold
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the macrocell size by
means of the maximum transmission power of the MS in
a GSM cell. If you set the parameter value at 5 dBm, the
division of cells into macrocells and microcells is not in
use.
Additional information
-
Range
5...39
Step
2
Unit
dBm
Formula for getting internal
value
internal_value = (gui_value - 43) / -2
Default value
35 dBm
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 320
DN9813866
GPRS Territory Update Guard Time (Cont.)
GSM Macrocell Threshold
Id:0900d8058089b05f
Confidential
463
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
GMAC
MML Full Name
GSM Macrocell Threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 320
9.128
GSM Microcell Threshold (GMIC)
Parameter name
GSM Microcell Threshold
Abbreviated name
gsmMicrocellThreshold
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the microcell size by
means of the maximum transmission power of the MS in
a GSM cell. If you set the parameter value at 43 dBm, the
division of cells into macrocells and microcells is not in
use.
Additional information
-
Range
5...39
Step
2
Unit
dBm
Formula for getting internal
value
internal_value = (gui_value - 43) / -2
Default value
33 dBm
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Table 321
464
GSM Macrocell Threshold (Cont.)
GSM Microcell Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
GMIC
MML Full Name
GSM Microcell Threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 321
9.129
GSM Microcell Threshold (Cont.)
HO preference order interference DL (HDL)
Parameter name
HO Preference Order Interference DL
Abbreviated name
hoPrefOrderInterfDl
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the order of preference
between intra-cell and inter-cell handovers when the
cause of the handover is downlink interference.
Additional information
-
Range
Inter-cell handover has greater priority (INTER) (0), Intracell handover has greater priority (INTRA) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Inter-cell handover has greater priority (INTER) ==> 0
Intra-cell handover has greater priority (INTRA) ==> 1
Default value
Inter-cell handover has greater priority (INTER) (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Table 322
DN9813866
HO Preference Order Interference DL
Id:0900d8058089b05f
Confidential
465
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
HDL
MML Full Name
HO preference order interference DL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 322
9.130
HO Preference Order Interference DL (Cont.)
HO preference order interference UL (HUL)
Parameter name
HO Preference Order Interference UL
Abbreviated name
hoPrefOrderInterfUl
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the order of preference
between intra-cell and inter-cell handovers when the
cause of the handover is uplink interference.
Additional information
-
Range
Inter-cell handover has greater priority (INTER) (0), Intracell handover has greater priority (INTRA) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
Inter-cell handover has greater priority (INTER) ==> 0
Intra-cell handover has greater priority (INTRA) ==> 1
Default value
Inter-cell handover has greater priority (INTER) (0)
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Table 323
466
HO Preference Order Interference UL
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
HUL
MML Full Name
HO preference order interference UL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 323
9.131
HO Preference Order Interference UL (Cont.)
IMSI based handover gsm cells anonymous ms (IBGA)
Parameter name
IMSI Based Handover GSM Cells Anonymous MS
Abbreviated name
ibhoGsmCellsAnoMs
Managed object
BSC
Multiplicity
1
Description
With this parameter you define in the case of intra-GSM
handover whether one of the existing Authorised
Networks is used for target cell selection or if all neighbour GSM cells are permitted. This parameter is used in
a serving GSM cell when a mobile subscriber is anonymous and IMSI based GSM-GSM handovers are enabled
in the serving GSM cell.
MML NOTE:
Range: 1..10, step 1
Default: ALL
Additional information
-
Range
0...10
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
optional
Special value
ALL (0)
Related functions
-
Modification
On-Line
Modified
-
Table 324
DN9813866
IMSI Based Handover GSM Cells Anonymous MS
Id:0900d8058089b05f
Confidential
467
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related parameters
aneId of ANE - Parameter ANE ID must be defined before
you can give this parameter.
Parameter relationships
-
Related options
•
IBHO (IMSI Based Handover) in BSC (80)
Related features
•
BSS12158: IMSI Based Handover
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
IBGA
MML Full Name
IMSI based handover gsm cells anonymous ms
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 324
9.132
IMSI Based Handover GSM Cells Anonymous MS (Cont.)
IMSI based handover WCDMA cells anonymous ms
(IBWA)
Parameter name
IMSI Based Handover WCDMA Cells Anonymous MS
Abbreviated name
ibhoWcdmaCellsAnoMs
Managed object
BSC
Multiplicity
1
Description
With this parameter you define in the case of WCDMA
handover whether one of the existing Authorised
Networks is used for target cell selection or all neighbour
WCDMA cells are permitted. This parameter is used in a
serving GSM cell when a mobile subscriber is anonymous and IMSI based GSM-WCDMA handovers are
enabled in the serving GSM cell.
MML NOTE:
Range: 1..10, step 1
Default: ALL
Additional information
-
Range
0...10
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Table 325
468
IMSI Based Handover WCDMA Cells Anonymous MS
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Default value notes
-
Required on Creation
optional
Special value
ALL (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
aneId of ANE - Parameter ANE ID must be defined before
you can give this parameter.
Parameter relationships
-
Related options
•
Inter System HO (ISHO Support In BSC) (56)
(optional) AND IBHO (IMSI Based Handover) in
BSC (80) (optional)
Related features
•
BSS12158: IMSI Based Handover
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
IBWA
MML Full Name
IMSI based handover WCDMA cells anonymous ms
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 325
9.133
initial AMR channel rate (IAC)
Parameter name
Initial AMR Channel Rate
Abbreviated name
initAmrChannelRate
Managed object
BSC
Multiplicity
1
Table 326
DN9813866
IMSI Based Handover WCDMA Cells Anonymous MS (Cont.)
Initial AMR Channel Rate
Id:0900d8058089b05f
Confidential
469
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the initial channel
rate in call setup, internal inter cell handover (HO)
and external HO for an Adaptive Multi Rate (AMR)
call.
MML Range:
1 = any rate, there is not any extra requirements by
the parameter and the chosen channel rate is
defined by taking into account the currently used
information for channel allocation
2 = AMR FR is allocated despite of the values of the
currently used information for channel allocation
Additional information
-
Range
Any rate (1), AMR FR (2)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Any rate ==> 1
AMR FR ==> 2
Default value
Any rate (1)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
AMR FR (50) (optional) OR Wideband AMR
(133) (optional)
Feature dependencies
•
•
BSS20960: Wideband AMR
BSS20249: AMR FR Licence Control
Interfaces
•
•
RACApp <-> RAC
BSC <-> RAC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
IAC
MML Full Name
initial AMR channel rate
Segment Level Parameter
-
Table 326
470
Initial AMR Channel Rate (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning
supported
Table 326
9.134
true
Initial AMR Channel Rate (Cont.)
Initial AMR codec type (IACT)
Parameter name
Initial AMR Codec Type
Abbreviated name
initialAMRCodecType
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the order of preference
between WB-AMR and AMR for mobile originating call.
Third choice is MSS codec list. Default value means that
the most preferred codec in MSS codec list is selected
when call (or connection) is established.
Additional information
-
Range
AMR has greater priority (0), AMR-WB has greater
priority (1), obey codec list given by MSS (2)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
AMR has greater priority ==> 0
AMR-WB has greater priority ==> 1
obey codec list given by MSS ==> 2
Default value
obey codec list given by MSS (2)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Wideband AMR (133)
Related features
•
BSS20960: Wideband AMR
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
IACT
Table 327
DN9813866
Initial AMR Codec Type
Id:0900d8058089b05f
Confidential
471
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Full Name
Initial AMR codec type
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 327
9.135
Initial AMR Codec Type (Cont.)
internal handover to external (IHTA)
Parameter name
Internal Handover To External
Abbreviated name
internalHoToExternal
Managed object
BSC
Multiplicity
1
Description
Parameter defines whether it is allowed to change
internal handover, where speech codec or channel
rate is changed, to MSC controlled in order to avoid
downlink muting.
NOTE: If MSC does not support unidirectional connection or conference bridge connection downlink
muting cannot be avoided by changing handover to
external; it is advisable to leave the parameter to
default value.
Additional information
-
Range
Not allowed (0), Allowed for AMR (1), Allowed for
other internal handovers than AMR (2), Allowed for
all internal handovers (3)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Not allowed ==> 0
Allowed for AMR ==> 1
Allowed for other internal handovers than AMR ==>
2
Allowed for all internal handovers ==> 3
Default value
Not allowed (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Table 328
472
Internal Handover To External
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
BSS20117: TCSM3i Support in BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
IHTA
MML Full Name
internal handover to external
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 328
9.136
Internal Handover To External (Cont.)
intra segment SDCCH HO guard (ISS)
Parameter name
Intra Segment SDCCH HO Guard
Abbreviated name
intraSegSdcchHoGuard
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the guard time for
attempting an SDCCH handover from the BCCH BTS
resource layer to another resource layer in a segment.
Additional information
-
Range
0...255
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
255 s
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Table 329
DN9813866
Base Station Controller (BSC) radio network object parameters
Intra Segment SDCCH HO Guard
Id:0900d8058089b05f
Confidential
473
Base Station Controller (BSC) radio network object parameters
Parameter relationships
Related options
Related features
BSS Radio Network Parameter Dictionary
-
•
-
•
•
Interfaces
Common BCCH EGSM900 (47) (optional) OR
Common BCCH GSM1800 (48) (optional) OR Multi
BCF Control (42) (optional) OR Common BCCH
GSM800 (57) (optional) OR Common BCCH
GSM1900 (58) (optional)
RACApp <-> RAC
BSC <-> RAC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
ISS
MML Full Name
intra segment SDCCH HO guard
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 329
9.137
Intra Segment SDCCH HO Guard (Cont.)
ISHO preferred for non-DTM MS (IPND)
Parameter name
ISHO Preferred For Non-DTM MS
Abbreviated name
ishoPreferredForNonDtmMs
Managed object
BSC
Multiplicity
1
Description
With this parameter the operator can determine
whether an inter-system handover is to be triggered
for a DTM incapable but WCDMA capable MS as
soon as an appropriate WCDMA target cell is available.
An inter-system handover can be triggered for a CS
connection if the ISHO procedures are enabled in
the BSC and if the "ISHO Preferred For Non-DTM
MS" parameter has the value "Triggered".
NOTE:
MML Range:
Y = An inter-system handover is to be triggered for
a DTM incapable but WCDMA capable MS,
N = An inter-system handover is not to be triggered
for a DTM incapable but WCDMA capable MS
Default: N
Table 330
474
ISHO Preferred For Non-DTM MS
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Additional information
-
Range
Not triggered (N) (0), Triggered (Y) (1)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Not triggered (N) ==> 0
Triggered (Y) ==> 1
Default value
Not triggered (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Inter System HO (ISHO Support In BSC) (56)
(optional) AND ( BSC GPRS Param Enabled
(GPRS O&M in BSC) (39) (optional) OR
Enhanced GPRS (EGPRS) Usage (51)
(optional) )
Feature dependencies
•
BSS20088: Dual Transfer Mode (DTM)
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
IPND
MML Full Name
ISHO preferred for non-DTM MS
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 330
9.138
IBNACC enabled ()
Parameter name
IBNACC Enabled
Abbreviated name
ibNaccEnabled
Table 331
DN9813866
ISHO Preferred For Non-DTM MS (Cont.)
IBNACC Enabled
Id:0900d8058089b05f
Confidential
475
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
Defines the state of IB-NACC in BSC. Not a user
parameter.
Additional information
-
Range
IB-NACC is not enabled in BSC (0), IB-NACC is
enabled in BSC (1)
Step
-
Units
-
Formula for getting
internal value
gui ==> internal
IB-NACC is not enabled in BSC ==> 0
IB-NACC is enabled in BSC ==> 1
Default value
IB-NACC is not enabled in BSC (0)
Default value notes
-
Required on creation
Value set by the system
Child parameters
-
Modification
Not modifiable
Modified
read-only
Related parameters
naccUsage of BSC - The parameter is dependant
on the BSC parameter NACC enabled and can be
modified to 0 (NACC is supported in adjacent
segment) only, if the NACC enabled parameter is Y.
Parameter relationships
-
Related options
-
Feature dependencies
BSS20083: Inter-BSC Network Assisted Cell
Change (NACC)
Interfaces
-
References
-
File based provisioning
supported
false
MML Abbreviated Name
-
MML Commands
-
MML Full Name
IBNACC enabled
Segment Level Parameter
-
Table 331
476
IBNACC Enabled (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.139
Base Station Controller (BSC) radio network object parameters
LAPD load threshold (LAPDL)
Parameter name
LAPD Load Threshold
Abbreviated name
lapdLoadThr
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the threshold for the
proportion of rejected measurement results in all
measurement results. An overload in the telecom
Abis LAPD Link causes the rejections. If this threshold is exceeded, the LAPD Link is regarded as overloaded, and the BSC generates the relevant alarm.
MML Range and Step: 0..10000 = 0..100% (step
size is 0.01%).
Additional information
-
Range
0...10000
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
150
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
LAPDL
MML Full Name
LAPD load threshold
Segment Level Parameter
-
Table 332
DN9813866
RAC <-> RACApp
RAC <-> BSC
LAPD Load Threshold
Id:0900d8058089b05f
Confidential
477
Base Station Controller (BSC) radio network object parameters
File Based Provisioning
supported
Table 332
9.140
BSS Radio Network Parameter Dictionary
true
LAPD Load Threshold (Cont.)
load rate for channel search (CLR)
Parameter name
Load Rate For Channel Search
Abbreviated name
loadRateChSearch
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the general load
limit for traffic channels in a cell under the BSC. If
the TCH load in a cell is below the limit, the traffic
channels for speech and single slot data calls are
allocated using rotation between TRXs in a cell and
between TSLs of a TRX. If the load limit has been
reached or exceeded, the TCH allocation is performed trying to save larger spaces of idle FR
resources for the possible multislot HSCSD calls by
preferring small gaps of free resources and ends of
a TRX for single slot calls.
Note:
If the BTS-specific parameter cell load for channel
search has been set (the value is not 0) in a BTS,
this will override the effect of the BSC level parameter in that BTS.
478
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting
internal value
internal_value = gui_value
Default value
100 %
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Table 333
Load Rate For Channel Search
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Related parameters
cellLoadForChannelSearch of BTS - If the BTSspecific parameter Cell Load For Channel Search
has been set (the value is not 0) in a BTS, this will
override the effect of the BSC level parameter in
that BTS.
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
CLR
MML Full Name
load rate for channel search
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 333
9.141
Base Station Controller (BSC) radio network object parameters
RAC <-> RACApp
RAC <-> BSC
Load Rate For Channel Search (Cont.)
local switching enabled for intercepted calls (LSEIC)
Parameter name
Local Switching Enabled For Intercepted Calls
Abbreviated name
lsEnabledInterceptedCalls
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you can enable/disable Local
Switching for calls under lawful interception.
To disable Local Switching for calls under lawful
interception you need to have Shared Secret key
entered and MSISDN file activated in BSC.
Additional information
-
Range
Disabled (0), Enabled (1)
Step
-
Units
-
Table 334
DN9813866
Local Switching Enabled For Intercepted Calls
Id:0900d8058089b05f
Confidential
479
Base Station Controller (BSC) radio network object parameters
Formula for getting
internal value
BSS Radio Network Parameter Dictionary
gui ==> internal
Disabled ==> 0
Enabled ==> 1
Default value
Enabled (1)
Default value notes
Local Switching enabled for calls under lawful interception
Required on creation
optional
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Feature dependencies
-
Interfaces
•
•
References
-
File based provisioning
supported
true
MML Abbreviated Name
LSEIC
MML Commands
EEM, EEO
MML Full Name
local switching enabled for interscepted calls
Segment Level Parameter
-
Table 334
9.142
BSC <-> RAC
RAC <-> RACApp
Local Switching Enabled For Intercepted Calls (Cont.)
lower limit for FR TCH resources (HRL)
Parameter name
Lower Limit For FR TCH Resources
Abbreviated name
btsLoadDepTchRateLower
Managed object
BSC
Multiplicity
1
Table 335
480
Local Switching for Packet Abis (156)
(optional) AND ( Packet Abis over TDM (151)
(optional) OR Packet Abis over IP/Eth (150)
(optional) )
Lower Limit For FR TCH Resources
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Description
The parameter controls the TCH channel rate
determination on the BSC level according to the cell
load in traffic channel allocation. With this parameter you define the lower limit for the percentage of
free full rate resources. Full rate TCHs are allocated
until the number of free full rate resources is
reduced below the value of the parameter. The half
rate resources are then allocated.
Additional information
Note: If parameter is used with Wideband AMR
(133), then optionality of (Half Rate (17) OR AMR
HR (72)) needs to be ON or CONFIG state. Note:
Wideband AMR optionality (133) is valid only for
Metrosite, Ultrasite, Flexi EDGE, BTSplus and Flexi
Multiradio BTSs.
Range
0...100
Step
1
Unit
%
Formula for getting
internal value
internal_value = gui_value
Default value
40 %
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Half Rate (17) (optional) OR AMR HR (72)
(optional)
Related features
•
•
BSS20960: Wideband AMR
BSS30060: AMR Capacity (AMR HR)
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
HRL
MML Full Name
lower limit for FR TCH resources
Segment Level Parameter
-
Table 335
DN9813866
Base Station Controller (BSC) radio network object parameters
Lower Limit For FR TCH Resources (Cont.)
Id:0900d8058089b05f
Confidential
481
Base Station Controller (BSC) radio network object parameters
File Based Provisioning
supported
Table 335
9.143
true
Lower Limit For FR TCH Resources (Cont.)
maximum mean holding time for SDCCHs (MAXHTS)
Parameter name
Maximum Mean Holding Time For SDCCHs
Abbreviated name
maxHldSdcch
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the maximum mean
holding time for signalling channels. If the mean holding
time during a measurement period is greater than or
equals the maximum mean holding time, the alarm
system prints out an alarm.
Additional information
-
Range
0...1440
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value
Default value
30 min
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
MAXHTS
MML Full Name
maximum mean holding time for SDCCHs
Segment Level Parameter
-
Table 336
482
BSS Radio Network Parameter Dictionary
Maximum Mean Holding Time For SDCCHs
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 336
9.144
Maximum Mean Holding Time For SDCCHs (Cont.)
maximum mean holding time for TCHs (MAXHTT)
Parameter name
Maximum Mean Holding Time For TCHs
Abbreviated name
maxHldTch
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the maximum mean
holding time for traffic channels. If the mean holding time
during a measurement period is greater than or equals
the maximum mean holding time, the alarm system prints
out an alarm.
Additional information
-
Range
0...1440
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value
Default value
120 min
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
MAXHTT
MML Full Name
maximum mean holding time for TCHs
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 337
DN9813866
Maximum Mean Holding Time For TCHs
Id:0900d8058089b05f
Confidential
483
Base Station Controller (BSC) radio network object parameters
9.145
BSS Radio Network Parameter Dictionary
maximum number of DL TBF (MNDL)
Parameter name
Maximum Number Of DL TBF
Abbreviated name
pcuMaxNoDLtbfInCH
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the maximum number of
TBFs that a radio time slot can have in average, in a
GPRS territory, in the downlink direction.
Additional information
-
Range
1...9
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
9
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
-
•
•
Interfaces
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
MNDL
MML Full Name
maximum number of DL TBF
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 338
484
Maximum Number Of DL TBF
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.146
Base Station Controller (BSC) radio network object parameters
maximum number of UL TBF (MNUL)
Parameter name
Maximum Number Of UL TBF
Abbreviated name
pcuMaxNoULtbfInCH
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the maximum number of
TBFs that a radio time slot can have in average, in a
GPRS territory, in the uplink direction.
Additional information
-
Range
1...7
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
7
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
•
Related options
Related features
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
MNUL
MML Full Name
maximum number of UL TBF
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 339
DN9813866
Maximum Number Of UL TBF
Id:0900d8058089b05f
Confidential
485
Base Station Controller (BSC) radio network object parameters
9.147
maximum TCH transaction rate (MTTR)
Parameter name
Maximum TCH Transaction Rate
Abbreviated name
maxTchTransactionRate
Managed object
BSC
Multiplicity
1
Description
This parameter defines the maximum incoming (from
MSC to BSC) TCH transaction rate (transactions per
second) that is acceptable for changing internal
handover to external. In this context TCH transaction
means MSC controlled TCH handover or TCH assignment.
Additional information
-
Range
0...1000
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
50
Default value notes
-
Required on Creation
optional
Special value
changing internal handover to external is denied (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
tchTransactionCount of BSC - Parameter Maximum TCH
Transaction Rate defines the maximum incoming TCH
transaction rate that is acceptable for changing the
internal handover to external, and parameter TCH Transaction Count defines how many of those incoming TCH
transactions are taken into account when calculating the
average TCH transaction rate.
Parameter relationships
-
Related options
-
Related features
•
BSS20117: TCSM3i Support in BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
MTTR
MML Full Name
maximum TCH transaction rate
Segment Level Parameter
-
Table 340
486
BSS Radio Network Parameter Dictionary
Maximum TCH Transaction Rate
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 340
9.148
mean BEP limit MS multislot pwr prof 0 with 2 UL TSL
(BL02)
Parameter name
Mean BEP Limit MS Multislot Pwr Prof 0 With 2 UL TSL
Abbreviated name
meanBepLimitUL_Prof0_2tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the mean Bit Error Probability
(BEP) limit for MS multislot power profile 0 when allocating 2 uplink TSLs. The measured mean BEP value is
compared to the value of this parameter when defining
how many uplink TSLs can be allocated. If the mean BEP
limit is set low, power reduction is not taken into account
so strictly in channel allocation.
Additional information
-
Range
0...31
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
21 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
Table 341
DN9813866
Maximum TCH Transaction Rate (Cont.)
Mean BEP Limit MS Multislot Pwr Prof 0 With 2 UL TSL
Id:0900d8058089b05f
Confidential
487
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Abbreviated Name
BL02
MML Full Name
mean BEP limit MS multislot pwr prof 0 with 2 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 341
9.149
mean BEP limit MS multislot pwr prof 0 with 3 UL TSL
(BL03)
Parameter name
Mean BEP Limit MS Multislot Pwr Prof 0 With 3 UL TSL
Abbreviated name
meanBepLimitUL_Prof0_3tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the mean Bit Error Probability
(BEP) limit for MS multislot power profile 0 when allocating 3 uplink TSLs. The measured mean BEP value is
compared to the value of this parameter when defining
how many uplink TSLs can be allocated. If the mean BEP
limit is set low, power reduction is not taken into account
so strictly in channel allocation.
Additional information
-
Range
0...31
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
26 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Table 342
488
Mean BEP Limit MS Multislot Pwr Prof 0 With 2 UL TSL (Cont.)
Mean BEP Limit MS Multislot Pwr Prof 0 With 3 UL TSL
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
BL03
MML Full Name
mean BEP limit MS multislot pwr prof 0 with 3 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 342
9.150
mean BEP limit MS multislot pwr prof 0 with 4 UL TSL
(BL04)
Parameter name
Mean BEP Limit MS Multislot Pwr Prof 0 With 4 UL TSL
Abbreviated name
meanBepLimitUL_Prof0_4tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the mean Bit Error Probability
(BEP) limit for MS multislot power profile 0 when allocating 4 uplink TSLs. The measured mean BEP value is
compared to the value of this parameter when defining
how many uplink TSLs can be allocated. If the mean BEP
limit is set low, power reduction is not taken into account
so strictly in channel allocation.
Additional information
-
Range
0...31
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
30 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 343
DN9813866
Mean BEP Limit MS Multislot Pwr Prof 0 With 3 UL TSL (Cont.)
Mean BEP Limit MS Multislot Pwr Prof 0 With 4 UL TSL
Id:0900d8058089b05f
Confidential
489
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
BL04
MML Full Name
mean BEP limit MS multislot pwr prof 0 with 4 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 343
9.151
mean BEP limit MS multislot pwr prof 1 with 2 UL TSL
(BL12)
Parameter name
Mean BEP Limit MS Multislot Pwr Prof 1 With 2 UL TSL
Abbreviated name
meanBepLimitUL_Prof1_2tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the mean Bit Error Probability
(BEP) limit for MS multislot power profile 1 when allocating 2 uplink TSLs. The measured mean BEP value is
compared to the value of this parameter when defining
how many uplink TSLs can be allocated. If the mean BEP
limit is set low, power reduction is not taken into account
so strictly in channel allocation.
Additional information
-
Range
0...31
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
20 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Table 344
490
Mean BEP Limit MS Multislot Pwr Prof 0 With 4 UL TSL (Cont.)
Mean BEP Limit MS Multislot Pwr Prof 1 With 2 UL TSL
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
BL12
MML Full Name
mean BEP limit MS multislot pwr prof 1 with 2 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 344
9.152
mean BEP limit MS multislot pwr prof 1 with 3 UL TSL
(BL13)
Parameter name
Mean BEP Limit MS Multislot Pwr Prof 1 With 3 UL
TSL
Abbreviated name
meanBepLimitUL_Prof1_3tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the mean Bit Error Probability (BEP) limit for MS multislot power profile 1
when allocating 3 uplink TSLs. The measured
mean BEP value is compared to the value of this
parameter when defining how many uplink TSLs
can be allocated. If the mean BEP limit is set low,
power reduction is not taken into account so strictly
in channel allocation.
Additional information
-
Range
0...31
Step
1
Unit
dB
Table 345
DN9813866
Mean BEP Limit MS Multislot Pwr Prof 1 With 2 UL TSL (Cont.)
Mean BEP Limit MS Multislot Pwr Prof 1 With 3 UL TSL
Id:0900d8058089b05f
Confidential
491
Base Station Controller (BSC) radio network object parameters
Formula for getting
internal value
internal_value = gui_value
Default value
25 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in
BSC) (39) (optional) OR Enhanced GPRS
(EGPRS) Usage (51) (optional)
Feature dependencies
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
BL13
MML Full Name
mean BEP limit MS multislot pwr prof 1 with 3 UL
TSL
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 345
9.153
Mean BEP Limit MS Multislot Pwr Prof 1 With 3 UL TSL (Cont.)
mean BEP limit MS multislot pwr prof 1 with 4 UL TSL
(BL14)
Parameter name
Mean BEP Limit MS Multislot Pwr Prof 1 With 4 UL TSL
Abbreviated name
meanBepLimitUL_Prof1_4tsl
Managed object
BSC
Multiplicity
1
Table 346
492
BSS Radio Network Parameter Dictionary
Mean BEP Limit MS Multislot Pwr Prof 1 With 4 UL TSL
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
This parameter indicates the mean Bit Error Probability
(BEP) limit for MS multislot power profile 1 when allocating 4 uplink TSLs. The measured mean BEP value is
compared to the value of this parameter when defining
how many uplink TSLs can be allocated. If the mean BEP
limit is set low, power reduction is not taken into account
so strictly in channel allocation.
Additional information
-
Range
0...31
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
30 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
BL14
MML Full Name
mean BEP limit MS multislot pwr prof 1 with 4 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 346
9.154
Mean BEP Limit MS Multislot Pwr Prof 1 With 4 UL TSL (Cont.)
mean BEP limit MS multislot pwr prof 2 with 3 UL TSL
(BL23)
Parameter name
Table 347
DN9813866
Mean BEP Limit MS Multislot Pwr Prof 2 With 3 UL TSL
Mean BEP Limit MS Multislot Pwr Prof 2 With 3 UL TSL
Id:0900d8058089b05f
Confidential
493
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Abbreviated name
meanBepLimitUL_Prof2_3tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the mean Bit Error Probability
(BEP) limit for MS multislot power profile 2 when allocating 3 uplink TSLs. The measured mean BEP value is
compared to the value of this parameter when defining
how many uplink TSLs can be allocated. If the mean BEP
limit is set low, power reduction is not taken into account
so strictly in channel allocation.
Additional information
-
Range
0...31
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
24 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
BL23
MML Full Name
mean BEP limit MS multislot pwr prof 2 with 3 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 347
494
Mean BEP Limit MS Multislot Pwr Prof 2 With 3 UL TSL (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.155
mean BEP limit MS multislot pwr prof 2 with 4 UL TSL
(BL24)
Parameter name
Mean BEP Limit MS Multislot Pwr Prof 2 With 4 UL TSL
Abbreviated name
meanBepLimitUL_Prof2_4tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the mean Bit Error Probability
(BEP) limit for MS multislot power profile 2 when allocating 4 uplink TSLs. The measured mean BEP value is
compared to the value of this parameter when defining
how many uplink TSLs can be allocated. If the mean BEP
limit is set low, power reduction is not taken into account
so strictly in channel allocation.
Additional information
-
Range
0...31
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
29 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
BL24
MML Full Name
mean BEP limit MS multislot pwr prof 2 with 4 UL TSL
Segment Level Parameter
-
Table 348
DN9813866
Base Station Controller (BSC) radio network object parameters
Mean BEP Limit MS Multislot Pwr Prof 2 With 4 UL TSL
Id:0900d8058089b05f
Confidential
495
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 348
9.156
Mean BEP Limit MS Multislot Pwr Prof 2 With 4 UL TSL (Cont.)
measurement period for high TCH interference supervision (PRDHIF)
Parameter name
Meas Period For High TCH Interference Supervision
Abbreviated name
prdHighIf
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the measurement period
for the high TCH interference supervision.
Additional information
-
Range
5...1440
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value
Default value
120 min
Default value notes
-
Required on Creation
mandatory
Special value
Deactivated (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
PRDHIF
MML Full Name
measurement period for high TCH interference supervision
Segment Level Parameter
-
Table 349
496
RAC <-> RACApp
RAC <-> BSC
Meas Period For High TCH Interference Supervision
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 349
9.157
measurement period for SDCCH mean holding time supervision (PRDMHS)
Parameter name
Meas Period For SDCCH Mean Holding Time
Supervision
Abbreviated name
measPrdSdcch
Managed object
BSC
Multiplicity
1
Description
The parameter supervises too long mean holding
times in SDCCHs. With this parameter you define
the length of the measurement period. The alarms
are printed out only at the end of the measurement
period.
Additional information
-
Range
5...1440
Step
1
Unit
min
Formula for getting
internal value
internal_value = gui_value
Default value
60 min
Default value notes
-
Required on Creation
mandatory
Special value
Deactivated (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
References
-
Table 350
DN9813866
Meas Period For High TCH Interference Supervision (Cont.)
RAC <-> RACApp
RAC <-> BSC
Meas Period For SDCCH Mean Holding Time Supervision
Id:0900d8058089b05f
Confidential
497
Base Station Controller (BSC) radio network object parameters
MML Commands
EEN, EEO
MML Abbreviated Name
PRDMHS
MML Full Name
measurement period for SDCCH mean holding
time supervision
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 350
9.158
Meas Period For SDCCH Mean Holding Time Supervision (Cont.)
measurement period for supervision of BTS with no transactions (PRDBNT)
Parameter name
Meas Period For Supervision Of BTS With No Transact
Abbreviated name
prdNokBts
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the measurement period
for the supervision of BTSs with no transactions.
Additional information
-
Range
5...1440
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value
Default value
120 min
Default value notes
-
Required on Creation
mandatory
Special value
Deactivated (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Interfaces
Table 351
498
BSS Radio Network Parameter Dictionary
•
•
RAC <-> RACApp
RAC <-> BSC
Meas Period For Supervision Of BTS With No Transact
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
PRDBNT
MML Full Name
measurement period for supervision of BTS with no
transactions
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 351
9.159
measurement period for supervision of channel failure
rate (PRDCFR)
Parameter name
Meas Period For Supervision Of Channel Failure Rate
Abbreviated name
measPrdFail
Managed object
BSC
Multiplicity
1
Description
The parameter supervises channel failures both in traffic
channels and in SDCCHs. With this parameter you define
the length of the measurement period. The alarms are
printed out only at the end of the measurement period.
Additional information
-
Range
5...1440
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value
Default value
60 min
Default value notes
-
Required on Creation
mandatory
Special value
Deactivated (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
Table 352
DN9813866
Meas Period For Supervision Of BTS With No Transact (Cont.)
Meas Period For Supervision Of Channel Failure Rate
Id:0900d8058089b05f
Confidential
499
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
PRDCFR
MML Full Name
measurement period for supervision of channel failure
rate
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 352
9.160
measurement period for supervision of congestion in BTS
(PRDCNG)
Parameter name
Measurement Period For Supervision Of Congestion In
BTS
Abbreviated name
measPrdCh
Managed object
BSC
Multiplicity
1
Description
The parameter supervises SDCCH and TCH congestion
in a BTS. With this parameter you define the length of the
measurement period. The alarms are printed out only at
the end of the measurement period.
Additional information
-
Range
5...1440
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value
Default value
120 min
Default value notes
-
Required on Creation
mandatory
Special value
Deactivated (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Table 353
500
Meas Period For Supervision Of Channel Failure Rate (Cont.)
Measurement Period For Supervision Of Congestion In BTS
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
PRDCNG
MML Full Name
measurement period for supervision of congestion in BTS
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 353
9.161
measurement period for TCH mean holding time supervision (PRDMHT)
Parameter name
Meas Period For TCH Mean Holding Time Supervision
Abbreviated name
measTchMhold
Managed object
BSC
Multiplicity
1
Description
The parameter supervises too short and too long mean
holding times in traffic channels. With this parameter you
define the length of the measurement period. The alarms
are printed out only at the end of the measurement
period.
Additional information
-
Range
5...1440
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value
Default value
240 min
Default value notes
-
Required on Creation
mandatory
Special value
Deactivated (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 354
DN9813866
Measurement Period For Supervision Of Congestion In BTS (Cont.)
Meas Period For TCH Mean Holding Time Supervision
Id:0900d8058089b05f
Confidential
501
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
PRDMHT
MML Full Name
measurement period for TCH mean holding time supervision
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 354
9.162
minimum mean holding time for TCHs (MINHTT)
Parameter name
Minimum Mean Holding Time For TCHs
Abbreviated name
minHldTch
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the minimum mean
holding time for traffic channels. If the mean holding time
is below the minimum mean holding time and there have
been enough calls during the measurement period (the
number of seizures is greater than or equals the operatordefined threshold value), the alarm system prints out an
alarm.
Additional information
-
Range
0...65535
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
10 s
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Table 355
502
Meas Period For TCH Mean Holding Time Supervision (Cont.)
Minimum Mean Holding Time For TCHs
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEN, EEO
MML Abbreviated Name
MINHTT
MML Full Name
minimum mean holding time for TCHs
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 355
9.163
Minimum Mean Holding Time For TCHs (Cont.)
mobile country code (MCC)
Parameter name
MCC
Abbreviated name
adjacentCellIdMCC
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the MCC of the
adjacent cell (target cell). The identification consists
of the Mobile Country Code Number, Mobile
Network Code Number, Cell Identification and the
Location Area Code.
NOTE for MML:
MML Range: 0..999
MML modification: Online
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
MCC value of serving cell
Required on Creation
optional
Related functions
-
Table 356
DN9813866
MCC
Id:0900d8058089b05f
Confidential
503
Base Station Controller (BSC) radio network object parameters
Modification
Not modifiable
Modified
-
Related parameters
adjacentCellIdMNC of ADCE - If this parameter is
given then the parameter MNC is obligatory.
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
EAC, EAD, EAM, EAX, EAO, EAT, EAP
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 356
9.164
BSS Radio Network Parameter Dictionary
MCC (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 1
Abbreviated name
rnwMCC1
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Country
Code of a radio network.
Radio Network MCC 1 - 16 and Radio Network
MNC 1 - 16 parameters you can remove an existing
PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Table 357
504
Radio Network MCC 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC1 of BSC - If parameter is given then
parameter Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 357
9.165
Radio Network MCC 1 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 10
Abbreviated name
rnwMCC10
Managed object
BSC
Table 358
DN9813866
Base Station Controller (BSC) radio network object parameters
Radio Network MCC 10
Id:0900d8058089b05f
Confidential
505
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Multiplicity
1
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Country
Code of a radio network.
Radio Network MCC 1 - 16 and Radio Network
MNC 1 - 16 parameters you can remove an existing
PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC10 of BSC - If parameter is given then
parameter Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
Table 358
506
Radio Network MCC 10 (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 358
9.166
Base Station Controller (BSC) radio network object parameters
Radio Network MCC 10 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 11
Abbreviated name
rnwMCC11
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Country
Code of a radio network.
Radio Network MCC 1 - 16 and Radio Network
MNC 1 - 16 parameters you can remove an existing
PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Table 359
DN9813866
Radio Network MCC 11
Id:0900d8058089b05f
Confidential
507
Base Station Controller (BSC) radio network object parameters
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC11 of BSC - If parameter is given then
parameter Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 359
9.167
Radio Network MCC 11 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 12
Abbreviated name
rnwMCC12
Managed object
BSC
Multiplicity
1
Table 360
508
BSS Radio Network Parameter Dictionary
Radio Network MCC 12
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC12 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
Table 360
DN9813866
Radio Network MCC 12 (Cont.)
Id:0900d8058089b05f
Confidential
509
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- false
ported
Table 360
9.168
Radio Network MCC 12 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 13
Abbreviated name
rnwMCC13
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC13 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
Table 361
510
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Radio Network MCC 13
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 361
9.169
Radio Network MCC 13 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 14
Abbreviated name
rnwMCC14
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Table 362
DN9813866
Radio Network MCC 14
Id:0900d8058089b05f
Confidential
511
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC14 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 362
9.170
mobile country code (MCC)
Parameter name
Radio Network MCC 15
Abbreviated name
rnwMCC15
Managed object
BSC
Multiplicity
1
Table 363
512
Radio Network MCC 14 (Cont.)
Radio Network MCC 15
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC15 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
Table 363
DN9813866
Radio Network MCC 15 (Cont.)
Id:0900d8058089b05f
Confidential
513
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- false
ported
Table 363
9.171
Radio Network MCC 15 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 16
Abbreviated name
rnwMCC16
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC16 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
Table 364
514
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Radio Network MCC 16
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 364
9.172
Radio Network MCC 16 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 2
Abbreviated name
rnwMCC2
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Table 365
DN9813866
Radio Network MCC 2
Id:0900d8058089b05f
Confidential
515
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC2 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 365
9.173
mobile country code (MCC)
Parameter name
Radio Network MCC 3
Abbreviated name
rnwMCC3
Managed object
BSC
Multiplicity
1
Table 366
516
Radio Network MCC 2 (Cont.)
Radio Network MCC 3
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC3 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
Table 366
DN9813866
Radio Network MCC 3 (Cont.)
Id:0900d8058089b05f
Confidential
517
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- false
ported
Table 366
9.174
Radio Network MCC 3 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 4
Abbreviated name
rnwMCC4
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC4 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
Table 367
518
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Radio Network MCC 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 367
9.175
Radio Network MCC 4 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 5
Abbreviated name
rnwMCC5
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Table 368
DN9813866
Radio Network MCC 5
Id:0900d8058089b05f
Confidential
519
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC5 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 368
9.176
mobile country code (MCC)
Parameter name
Radio Network MCC 6
Abbreviated name
rnwMCC6
Managed object
BSC
Multiplicity
1
Table 369
520
Radio Network MCC 5 (Cont.)
Radio Network MCC 6
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC6 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
Table 369
DN9813866
Radio Network MCC 6 (Cont.)
Id:0900d8058089b05f
Confidential
521
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- false
ported
Table 369
9.177
Radio Network MCC 6 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 7
Abbreviated name
rnwMCC7
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC7 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
Table 370
522
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Radio Network MCC 7
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 370
9.178
Radio Network MCC 7 (Cont.)
mobile country code (MCC)
Parameter name
Radio Network MCC 8
Abbreviated name
rnwMCC8
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Table 371
DN9813866
Radio Network MCC 8
Id:0900d8058089b05f
Confidential
523
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC8 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 371
9.179
mobile country code (MCC)
Parameter name
Radio Network MCC 9
Abbreviated name
rnwMCC9
Managed object
BSC
Multiplicity
1
Table 372
524
Radio Network MCC 8 (Cont.)
Radio Network MCC 9
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Country Code
of a radio network.
Radio Network MCC 1 - 16 and Radio Network MNC 1 16 parameters you can remove an existing PLMN identifier from a PLMN list.
Value range: 0..999
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMNC9 of BSC - If parameter is given then parameter
Radio Network MNC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MCC
MML Full Name
mobile country code
Segment Level Parameter
-
Table 372
DN9813866
Radio Network MCC 9 (Cont.)
Id:0900d8058089b05f
Confidential
525
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- false
ported
Table 372
9.180
Radio Network MCC 9 (Cont.)
mobile network code (MNC)
Parameter name
MNC
Abbreviated name
adjacentCellIdMNC
Managed object
ADCE
Multiplicity
1
Description
With this parameter you define the MNC of the
adjacent cell (target cell). The identification consists
of the Mobile Country Code Number, Mobile
Network Code Number, Cell Identification and the
Location Area Code.
NOTE:
MML range: 0..999
MML modification: Online
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
MNC value of serving cell
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
adjacentCellIdMCC of ADCE - If this parameter is
given then the parameter MCC is obligatory.
Parameter relationships
-
Related options
-
Feature dependencies
-
Table 373
526
MNC
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Interfaces
•
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
EAC, EAD, EAM, EAX, EAO, EAT, EAP
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 373
9.181
Base Station Controller (BSC) radio network object parameters
MNC (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 1
Abbreviated name
rnwMNC1
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Table 374
DN9813866
Radio Network MNC 1
Id:0900d8058089b05f
Confidential
527
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC1 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 374
9.182
mobile network code (MNC)
Parameter name
Radio Network MNC 10
Abbreviated name
rnwMNC10
Managed object
BSC
Multiplicity
1
Table 375
528
Radio Network MNC 1 (Cont.)
Radio Network MNC 10
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Network
Code of a radio network.
By giving value 999 for the Radio Network MCC 1 16 and Radio Network MNC 1 - 16 parameters you
can remove an existing PLMN identifier from a
PLMN list.
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC10 of BSC - If parameter is given then
parameter Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Table 375
DN9813866
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Radio Network MNC 10 (Cont.)
Id:0900d8058089b05f
Confidential
529
Base Station Controller (BSC) radio network object parameters
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 375
9.183
Radio Network MNC 10 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 11
Abbreviated name
rnwMNC11
Managed object
BSC
Multiplicity
1
Table 376
530
BSS Radio Network Parameter Dictionary
Radio Network MNC 11
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Network
Code of a radio network.
By giving value 999 for the Radio Network MCC 1 16 and Radio Network MNC 1 - 16 parameters you
can remove an existing PLMN identifier from a
PLMN list.
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC11 of BSC - If parameter is given then
parameter Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Table 376
DN9813866
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Radio Network MNC 11 (Cont.)
Id:0900d8058089b05f
Confidential
531
Base Station Controller (BSC) radio network object parameters
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 376
9.184
Radio Network MNC 11 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 12
Abbreviated name
rnwMNC12
Managed object
BSC
Multiplicity
1
Table 377
532
BSS Radio Network Parameter Dictionary
Radio Network MNC 12
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Network
Code of a radio network.
By giving value 999 for the Radio Network MCC 1 16 and Radio Network MNC 1 - 16 parameters you
can remove an existing PLMN identifier from a
PLMN list.
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC12 of BSC - If parameter is given then
parameter Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Table 377
DN9813866
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Radio Network MNC 12 (Cont.)
Id:0900d8058089b05f
Confidential
533
Base Station Controller (BSC) radio network object parameters
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 377
9.185
Radio Network MNC 12 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 13
Abbreviated name
rnwMNC13
Managed object
BSC
Multiplicity
1
Table 378
534
BSS Radio Network Parameter Dictionary
Radio Network MNC 13
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Network
Code of a radio network.
By giving value 999 for the Radio Network MCC 1 16 and Radio Network MNC 1 - 16 parameters you
can remove an existing PLMN identifier from a
PLMN list.
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC13 of BSC - If parameter is given then
parameter Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Table 378
DN9813866
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Radio Network MNC 13 (Cont.)
Id:0900d8058089b05f
Confidential
535
Base Station Controller (BSC) radio network object parameters
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 378
9.186
Radio Network MNC 13 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 14
Abbreviated name
rnwMNC14
Managed object
BSC
Multiplicity
1
Table 379
536
BSS Radio Network Parameter Dictionary
Radio Network MNC 14
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Network
Code of a radio network.
By giving value 999 for the Radio Network MCC 1 16 and Radio Network MNC 1 - 16 parameters you
can remove an existing PLMN identifier from a
PLMN list.
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC14 of BSC - If parameter is given then
parameter Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Table 379
DN9813866
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Radio Network MNC 14 (Cont.)
Id:0900d8058089b05f
Confidential
537
Base Station Controller (BSC) radio network object parameters
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 379
9.187
Radio Network MNC 14 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 15
Abbreviated name
rnwMNC15
Managed object
BSC
Multiplicity
1
Table 380
538
BSS Radio Network Parameter Dictionary
Radio Network MNC 15
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of
the radio networks to where the SPC can be connected in multi-operator environment.
With this parameter you identify the Mobile Network
Code of a radio network.
By giving value 999 for the Radio Network MCC 1 16 and Radio Network MNC 1 - 16 parameters you
can remove an existing PLMN identifier from a
PLMN list.
MNC length must be always three digits if MCC is
310, 311, 312, 313, 314, 315, 316, 334, 338, 342,
344, 346, 348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16
parameters need to be defined in numeric order.
There must be as many Radio Network MCC
parameters defined as Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC15 of BSC - If parameter is given then
parameter Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Table 380
DN9813866
Multipoint A Interface for BSC (94) (optional)
AND Multi-operator BSS (122) (optional)
Radio Network MNC 15 (Cont.)
Id:0900d8058089b05f
Confidential
539
Base Station Controller (BSC) radio network object parameters
Feature dependencies
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 380
9.188
BSS Radio Network Parameter Dictionary
Radio Network MNC 15 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 16
Abbreviated name
rnwMNC16
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
Table 381
540
-
Radio Network MNC 16
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC16 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 381
9.189
mobile network code (MNC)
Parameter name
Radio Network MNC 2
Abbreviated name
rnwMNC2
Managed object
BSC
Multiplicity
1
Table 382
DN9813866
Radio Network MNC 16 (Cont.)
Radio Network MNC 2
Id:0900d8058089b05f
Confidential
541
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC2 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
Table 382
542
Radio Network MNC 2 (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 382
9.190
Radio Network MNC 2 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 3
Abbreviated name
rnwMNC3
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Table 383
DN9813866
Radio Network MNC 3
Id:0900d8058089b05f
Confidential
543
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC3 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 383
9.191
mobile network code (MNC)
Parameter name
Radio Network MNC 4
Abbreviated name
rnwMNC4
Managed object
BSC
Multiplicity
1
Table 384
544
Radio Network MNC 3 (Cont.)
Radio Network MNC 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC4 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
Table 384
DN9813866
Radio Network MNC 4 (Cont.)
Id:0900d8058089b05f
Confidential
545
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 384
9.192
Radio Network MNC 4 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 5
Abbreviated name
rnwMNC5
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Table 385
546
Radio Network MNC 5
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC5 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 385
9.193
mobile network code (MNC)
Parameter name
Radio Network MNC 6
Abbreviated name
rnwMNC6
Managed object
BSC
Multiplicity
1
Table 386
DN9813866
Radio Network MNC 5 (Cont.)
Radio Network MNC 6
Id:0900d8058089b05f
Confidential
547
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC6 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
Table 386
548
Radio Network MNC 6 (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 386
9.194
Radio Network MNC 6 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 7
Abbreviated name
rnwMNC7
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Table 387
DN9813866
Radio Network MNC 7
Id:0900d8058089b05f
Confidential
549
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC7 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 387
9.195
mobile network code (MNC)
Parameter name
Radio Network MNC 8
Abbreviated name
rnwMNC8
Managed object
BSC
Multiplicity
1
Table 388
550
Radio Network MNC 7 (Cont.)
Radio Network MNC 8
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC8 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
Table 388
DN9813866
Radio Network MNC 8 (Cont.)
Id:0900d8058089b05f
Confidential
551
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 388
9.196
Radio Network MNC 8 (Cont.)
mobile network code (MNC)
Parameter name
Radio Network MNC 9
Abbreviated name
rnwMNC9
Managed object
BSC
Multiplicity
1
Description
The parameter determines the PLMN identifiers of the
radio networks to where the SPC can be connected in
multi-operator environment.
With this parameter you identify the Mobile Network Code
of a radio network.
By giving value 999 for the Radio Network MCC 1 - 16
and Radio Network MNC 1 - 16 parameters you can
remove an existing PLMN identifier from a PLMN list.
MNC length must be always three digits if MCC is 310,
311, 312, 313, 314, 315, 316, 334, 338, 342, 344, 346,
348, 365, 376, 708, 722 or 732
NOTE:
MML Range:
0..99
0..999 OPTIONAL (Three digits MNC)
NetAct note:
Radio Network MCC 1 - Radio Network MCC 16 parameters need to be defined in numeric order. There must be
as many Radio Network MCC parameters defined as
Radio Network MNC parameters.
Additional information
-
Range
2...3
Step
-
Unit
characters
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Table 389
552
Radio Network MNC 9
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
rnwMCC9 of BSC - If parameter is given then parameter
Radio Network MCC is obligatory.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94) (optional) AND
Multi-operator BSS (122) (optional)
Related features
•
•
•
BSS21213: Multi-operator BSS
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
E7N,E7R,E7L
MML Abbreviated Name
MNC
MML Full Name
mobile network code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 389
9.197
MS distance behaviour (DISB)
Parameter name
MS Distance Behaviour
Abbreviated name
msDistanceBehaviour
Managed object
BSC
Multiplicity
1
Table 390
DN9813866
Radio Network MNC 9 (Cont.)
MS Distance Behaviour
Id:0900d8058089b05f
Confidential
553
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the executions allowed
after the Timing Advance has exceeded the threshold.
NOTE:
Range: 0..60, 255
0 (release immediately)
1 (1 s to try handover, release if handover does not
succeed)
.
.
.
60 (60 s to try handover, release if handover does not
succeed)
255 (no release, only handover attempts)
Additional information
-
Range
0...60
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
255
Default value notes
-
Required on Creation
mandatory
Special value
no release, only handover attempts (255)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
DISB
MML Full Name
MS distance behaviour
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 390
554
MS Distance Behaviour (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.198
Base Station Controller (BSC) radio network object parameters
M-plane packet drop period (MPLPDP)
Parameter name
M-plane Packet Drop Period
Abbreviated name
mPlanePacketDropPeriod
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter user defined the packet drop
period for M-plane packets.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
0...10000
Step
10
Units
ms
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MPLPDP
MML Commands
EEY, EEO
Table 391
DN9813866
M-plane Packet Drop Period
Id:0900d8058089b05f
Confidential
555
Base Station Controller (BSC) radio network object parameters
MML Full Name
M-plane packet drop period
Segment Level Parameter
-
Table 391
9.199
BSS Radio Network Parameter Dictionary
M-plane Packet Drop Period (Cont.)
MC-PPP assured forwarding class 1 (MCAFC1)
Parameter name
MC-PPP Assured Forwarding Class 1
Abbreviated name
mcpppAssuredForwardingClass1
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the mapping of the
Per-Hop-Behaviour (DSCP) to MC-PPP Assured
Forwarding Class 1.
NOTE: Default mapping between DSCP and MCPPP Class:
0 (00) (BE (Best Effort)),
1 (01) (AF1…AF3 (Assured Forwarding class
1…3)),
2 (10) (AF4 (Assured Forwarding class 4)),
3 (11) (EF (Expedited Forwarding))
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
-
Range
0...3
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
1
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Table 392
556
MC-PPP Assured Forwarding Class 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MCAFC1
MML Commands
EEY, EEO
MML Full Name
MC-PPP assured forwarding class 1
Segment Level Parameter
-
Table 392
9.200
MC-PPP Assured Forwarding Class 1 (Cont.)
MC-PPP assured forwarding class 2 (MCAFC2)
Parameter name
MC-PPP Assured Forwarding Class 2
Abbreviated name
mcpppAssuredForwardingClass2
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the mapping of the
Per-Hop-Behaviour (DSCP) to MC-PPP Assured
Forwarding Class 2.
NOTE: Default mapping between DSCP and MCPPP Class:
0 (00) (BE (Best Effort)),
1 (01) (AF1…AF3 (Assured Forwarding class
1…3)),
2 (10) (AF4 (Assured Forwarding class 4)),
3 (11) (EF (Expedited Forwarding))
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
Table 393
DN9813866
-
MC-PPP Assured Forwarding Class 2
Id:0900d8058089b05f
Confidential
557
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Range
0...3
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
1
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MCAFC2
MML Commands
EEY, EEO
MML Full Name
MC-PPP assured forwarding class 2
Segment Level Parameter
-
Table 393
9.201
MC-PPP assured forwarding class 3 (MCAFC3)
Parameter name
MC-PPP Assured Forwarding Class 3
Abbreviated name
mcpppAssuredForwardingClass3
3GPP name
-
Managed Object
BSC
Multiplicity
1
Table 394
558
MC-PPP Assured Forwarding Class 2 (Cont.)
MC-PPP Assured Forwarding Class 3
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
With this parameter you define the mapping of the
Per-Hop-Behaviour (DSCP) to MC-PPP Assured
Forwarding Class 3.
NOTE: Default mapping between DSCP and MCPPP Class:
0 (00) (BE (Best Effort)),
1 (01) (AF1…AF3 (Assured Forwarding class
1…3)),
2 (10) (AF4 (Assured Forwarding class 4)),
3 (11) (EF (Expedited Forwarding))
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
-
Range
0...3
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
1
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MCAFC3
MML Commands
EEY, EEO
MML Full Name
MC-PPP assured forwarding class 3
Table 394
DN9813866
MC-PPP Assured Forwarding Class 3 (Cont.)
Id:0900d8058089b05f
Confidential
559
Base Station Controller (BSC) radio network object parameters
Segment Level Parameter
Table 394
9.202
BSS Radio Network Parameter Dictionary
-
MC-PPP Assured Forwarding Class 3 (Cont.)
MC-PPP assured forwarding class 4 (MCAFC4)
Parameter name
MC-PPP Assured Forwarding Class 4
Abbreviated name
mcpppAssuredForwardingClass4
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the mapping of the
Per-Hop-Behaviour (DSCP) to MC-PPP Assured
Forwarding Class 4.
0 (00) (BE (Best Effort)),
1 (01) (AF1…AF3 (Assured Forwarding class
1…3)),
2 (10) (AF4 (Assured Forwarding class 4)),
3 (11) (EF (Expedited Forwarding))
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
-
Range
0...3
Step
1
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
2
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over TDM (151)
Table 395
560
MC-PPP Assured Forwarding Class 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Feature dependencies
BSS21440: Packet Abis over TDM
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MCAFC4
MML Commands
EEY, EEO
MML Full Name
MC-PPP assured forwarding class 4
Segment Level Parameter
-
Table 395
9.203
MC-PPP Assured Forwarding Class 4 (Cont.)
MC-PPP best effort (MCBE)
Parameter name
MC-PPP Best Effort
Abbreviated name
mcpppBestEffort
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the mapping of the
Per-Hop-Behaviour (DSCP) to MC-PPP best effort
Class.
NOTE: Default mapping between DSCP and MCPPP Class:
0 (00) (BE (Best Effort)),
1 (01) (AF1…AF3 (Assured Forwarding class
1…3)),
2 (10) (AF4 (Assured Forwarding class 4)),
3 (11) (EF (Expedited Forwarding))
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Additional information
-
Range
0...3
Step
1
Units
-
Table 396
DN9813866
MC-PPP Best Effort
Id:0900d8058089b05f
Confidential
561
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
internal_value =gui_value
Default value
0
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
MCBE
MML Commands
EEY, EEO
MML Full Name
MC-PPP best effort
Segment Level Parameter
-
Table 396
9.204
MC-PPP Expedited Forwarding (MCEF)
Parameter name
MC-PPP Expedited Forwarding
Abbreviated name
mcpppExpeditedForwarding
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the mapping of the
Per-Hop-Behaviour (DSCP) to MC-PPP Expedited
Forwarding class
Additional information
-
Range
0...3
Step
1
Unit
-
Table 397
562
MC-PPP Best Effort (Cont.)
MC-PPP Expedited Forwarding
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
internal_value = gui_value
Default value
3
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Packet Abis over TDM (151)
Feature dependencies
•
BSS21440: Packet Abis over TDM
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEY, EEO
MML Abbreviated Name
MCEF
MML Full Name
MC-PPP Expedited Forwarding
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 397
9.205
MC-PPP Expedited Forwarding (Cont.)
NACC enabled (NACC)
Parameter name
NACC Enabled
Abbreviated name
naccUsage
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the usage of NACC procedures. When enabled the MS (when in packet transfer
mode) may receive neighbour cell system information
messages in serving cell before the cell reselection is
executed. When enabled also the Packet SI Status
support is activated.
Additional information
-
Range
NACC is disabled (N) (0), NACC is enabled (Y) (1)
Table 398
DN9813866
Base Station Controller (BSC) radio network object parameters
NACC Enabled
Id:0900d8058089b05f
Confidential
563
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
NACC is disabled (N) ==> 0
NACC is enabled (Y) ==> 1
Default value
NACC is disabled (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NACC (Network Assisted Cell Change) (81)
Related features
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
NACC
MML Full Name
NACC enabled
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 398
9.206
Nbr measurement period in NC2 (NMPN)
Parameter name
Nbr measurement period in NC2
Abbreviated name
nbrMeasPeriodInNC2
Managed object
BSC
Multiplicity
1
Description
This parameter defines how many measurement reports
PCU2 receives from TD-SCDMA capable Mobile Station
before PCU2 orders the Mobile Station back to NC0
mode, if suitable TD-SCDMA cell does not exist.
Additional information
-
Range
1... 8
Table 399
564
NACC Enabled (Cont.)
Nbr measurement period in NC2
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
IS-NCCR for TD-SCDMA (171)
Related features
•
RG301736 IS-NCCR for TD-SCDMA
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EEO, EEM
MML Abbreviated Name
NMPN
MML Full Name
Nbr measurement period in NC2
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 399
9.207
NCCR control mode (NCM)
Parameter name
NCCR Control Mode
Abbreviated name
nccrControlMode
Managed object
BSC
Multiplicity
1
Description
With this parameter you enable or disable the NCCR in
the BSC. If NCCR is enabled then the MS in RR Packet
transfer mode and RR Packet idle mode sends neighbor
cell measurements to the network and the network
commands the MS to perform cell reselection. MS is in
NC2 mode. If NCCR is disabled then the MS will make an
autonomous cell reselection. MS is in NC0 mode.
Additional information
-
Table 400
DN9813866
Nbr measurement period in NC2 (Cont.)
NCCR Control Mode
Id:0900d8058089b05f
Confidential
565
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Range
NCCR is disabled for all mobile stations. (0), NCCR is
enabled for release 97 onwards MS (1), NCCR is enabled
for release 99 onwards MS (2), NCCR is enabled for
release 4 onwards MS (3), NCCR is enabled for all
mobile stations. (4)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
NCCR is disabled for all mobile stations. ==> 0
NCCR is enabled for release 97 onwards MS ==> 1
NCCR is enabled for release 99 onwards MS ==> 2
NCCR is enabled for release 4 onwards MS ==> 3
NCCR is enabled for all mobile stations. ==> 4
Default value
NCCR is disabled for all mobile stations. (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85)
Related features
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 44.018, 44.060, 45.008
MML Commands
EEM, EEO
MML Abbreviated Name
NCM
MML Full Name
NCCR control mode
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 400
9.208
NCCR idle mode reporting period (NIRP)
Parameter name
NCCR Idle Mode Reporting Period
Abbreviated name
nccrIdleModeRepPeriod
Table 401
566
NCCR Control Mode (Cont.)
NCCR Idle Mode Reporting Period
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the Network Control (NC)
measurement reporting period for the MSS in RR Packet
Idle mode.
Additional information
-
Range
0.48 s (0), 0.96 s (1), 1.92 s (2), 3.84 s (3), 7.68 s (4),
15.36 s (5), 30.72 s (6), 61.44 s (7)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
0.48 s ==> 0
0.96 s ==> 1
1.92 s ==> 2
3.84 s ==> 3
7.68 s ==> 4
15.36 s ==> 5
30.72 s ==> 6
61.44 s ==> 7
Default value
15.36 s (5)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85) OR IS-NCCR for TDSCDMA (171)
Related features
•
•
BSS11112 Network Controlled Cell Reselection
(NCCR)
RG301736 IS-NCCR for TD-SCDMA
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 44.018, 44.060, 45.008
MML Commands
EEM, EEO
MML Abbreviated Name
NIRP
MML Full Name
NCCR idle mode reporting period
Segment Level Parameter
-
Table 401
DN9813866
NCCR Idle Mode Reporting Period (Cont.)
Id:0900d8058089b05f
Confidential
567
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 401
9.209
NCCR Idle Mode Reporting Period (Cont.)
NCCR neighbor cell penalty (NNCP)
Parameter name
NCCR Neighbor Cell Penalty
Abbreviated name
nccrNeighborCellPenalty
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the penalty time for a
neighbor cell after a NCCR to that cell has failed.
Additional information
-
Range
1...60
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
6s
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85)
Related features
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
NNCP
MML Full Name
NCCR neighbor cell penalty
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 402
568
NCCR Neighbor Cell Penalty
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.210
NCCR return to old cell time (NOCT)
Parameter name
NCCR Return To Old Cell Time
Abbreviated name
nccrReturnOldCellTime
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the start value for a
timer that together with another timer (NCCR target
cell penalty time) counteracts the "Ping-Pong"
effect.
Additional information
-
Range
5...20
Step
1
Unit
s
Formula for getting
internal value
internal_value = gui_value
Default value
10 s
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85)
Feature dependencies
•
BSS20117: TCSM3i Support in BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
NOCT
MML Full Name
NCCR return to old cell time
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 403
DN9813866
Base Station Controller (BSC) radio network object parameters
NCCR Return To Old Cell Time
Id:0900d8058089b05f
Confidential
569
Base Station Controller (BSC) radio network object parameters
9.211
BSS Radio Network Parameter Dictionary
NCCR target cell penalty time (NTPT)
Parameter name
NCCR Target Cell Penalty Time
Abbreviated name
nccrTargetCellPenalty
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the time during which
NCCR is not allowed for a mobile station that has been
ordered to select another cell and has returned from that
cell to the original cell.
Together with another timer (NCCR Return To Old Cell
Time) counteracts the "Ping-Pong" effect.
Additional information
-
Range
5...60
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
10 s
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85)
Related features
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
NTPT
MML Full Name
NCCR target cell penalty time
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 404
570
NCCR Target Cell Penalty Time
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.212
Base Station Controller (BSC) radio network object parameters
NCCR transfer mode reporting period (NTRP)
Parameter name
NCCR Transfer Mode Reporting Period
Abbreviated name
nccrTraModeRepPeriod
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the Network Control (NC)
measurement reporting period for the MSS in RR Packet
Transfer mode.
Additional information
-
Range
0.48 s (0), 0.96 s (1), 1.92 s (2), 3.84 s (3), 7.68 s (4),
15.36 s (5), 30.72 s (6), 61.44 s (7)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
0.48 s ==> 0
0.96 s ==> 1
1.92 s ==> 2
3.84 s ==> 3
7.68 s ==> 4
15.36 s ==> 5
30.72 s ==> 6
61.44 s ==> 7
Default value
0.48 s (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
NC Cell Re-selection (85) OR IS-NCCR for TDSCDMA (171)
Related features
•
•
BSS11112: Network Controlled Cell Reselection
(NCCR)
RG301736 IS-NCCR for TD-SCDMA
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 44.018, 44.060, 45.008
MML Commands
Table 405
DN9813866
EEM, EEO
NCCR Transfer Mode Reporting Period
Id:0900d8058089b05f
Confidential
571
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Abbreviated Name
NTRP
MML Full Name
NCCR transfer mode reporting period
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 405
9.213
NCCR Transfer Mode Reporting Period (Cont.)
NRI (NRI list)
Parameter name
NRI List 1
Abbreviated name
nriList1
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 1.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is
changed from 0 (default value), none of the NRI
values (NRI List 1, NRI List 2, NRI List 3, NRI List 4,
NRI List 5, NRI List 6, NRI List 7, NRI List 8, NRI List
9, NRI List 10) must not exceed the decimal value
range which CS NRI Length indicates.
Parameter relationships
-
Related options
-
Feature dependencies
•
Table 406
572
BSS20092: Multipoint A Interface for BSC
NRI List 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 406
9.214
Base Station Controller (BSC) radio network object parameters
NRI List 1 (Cont.)
NRI (NRI list)
Parameter name
NRI List 10
Abbreviated name
nriList10
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 10.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Table 407
DN9813866
NRI List 10
Id:0900d8058089b05f
Confidential
573
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 407
9.215
NRI List 10 (Cont.)
NRI (NRI list)
Parameter name
NRI List 2
Abbreviated name
nriList2
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 2.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Table 408
574
NRI List 2
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 408
9.216
NRI List 2 (Cont.)
NRI (NRI list)
Parameter name
NRI List 3
Abbreviated name
nriList3
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 3.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Table 409
DN9813866
NRI List 3
Id:0900d8058089b05f
Confidential
575
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 409
9.217
NRI List 3 (Cont.)
NRI (NRI list)
Parameter name
NRI List 4
Abbreviated name
nriList4
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 4.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Table 410
576
NRI List 4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 410
9.218
NRI List 4 (Cont.)
NRI (NRI list)
Parameter name
NRI List 5
Abbreviated name
nriList5
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 5.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Table 411
DN9813866
NRI List 5
Id:0900d8058089b05f
Confidential
577
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 411
9.219
NRI List 5 (Cont.)
NRI (NRI list)
Parameter name
NRI List 6
Abbreviated name
nriList6
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 6.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Step
1
Unit
-
Table 412
578
NRI List 6
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 412
9.220
NRI List 6 (Cont.)
NRI (NRI list)
Parameter name
NRI List 7
Abbreviated name
nriList7
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 7.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Table 413
DN9813866
NRI List 7
Id:0900d8058089b05f
Confidential
579
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 413
9.221
NRI List 7 (Cont.)
NRI (NRI list)
Parameter name
NRI List 8
Abbreviated name
nriList8
Managed object
BSC
Multiplicity
1
Description
With this parameter you define NRI List 8.
MML NOTE: Required on creation: optional
Table 414
580
NRI List 8
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 414
9.222
NRI (NRI list)
Parameter name
NRI List 9
Abbreviated name
nriList9
Managed object
BSC
Multiplicity
1
Table 415
DN9813866
NRI List 8 (Cont.)
NRI List 9
Id:0900d8058089b05f
Confidential
581
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define NRI List 9.
MML NOTE: Required on creation: optional
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10) must not
exceed the decimal value range which CS NRI Length
indicates.
Parameter relationships
-
Related options
-
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I,E7M,E7D
MML Abbreviated Name
NRI list
MML Full Name
NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 415
9.223
Null NRI (NULLNRI)
Parameter name
CS Null-NRI
Abbreviated name
csNullNri
Table 416
582
NRI List 9 (Cont.)
CS Null-NRI
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Managed object
BSC
Multiplicity
1
Description
With this parameter you define CS Null-NRI.
This value can be defined for each MSC/MSS
Additional information
-
Range
0...1023
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65535
Default value notes
-
Required on Creation
mandatory
Special value
Not Used (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
csNriLength of BSC - When CS NRI Length is changed
from 0 (default value), none of the NRI values (NRI List 1,
NRI List 2, NRI List 3, NRI List 4, NRI List 5, NRI List 6,
NRI List 7, NRI List 8, NRI List 9, NRI List 10, Null-NRI)
must not exceed the decimal value range which CS NRI
Length indicates.
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94)
Related features
•
•
BSS20092: Multipoint A Interface for BSC
BSS21217: Multipoint A Load Balancing
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
•
3GPP Reference: 23.236
MML Commands
E7I, E7A, E7D, E7M
MML Abbreviated Name
NULLNRI
MML Full Name
Null NRI
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 416
DN9813866
CS Null-NRI (Cont.)
Id:0900d8058089b05f
Confidential
583
Base Station Controller (BSC) radio network object parameters
9.224
BSS Radio Network Parameter Dictionary
number of ignored transcoder failures (ITCF)
Parameter name
Number Of Ignored Transcoder Failures
Abbreviated name
callReleaseLimit
Managed object
BSC
Multiplicity
1
Description
With this parameter you define how many successive
remote transcoder failures the BSC may receive before it
releases the call.
Additional information
-
Range
0...5
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
0
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
ITCF
MML Full Name
number of ignored transcoder failures
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 417
9.225
Number Of Ignored Transcoder Failures
number of preferred cells (NPC)
Parameter name
Table 418
584
Number Of Preferred Cells
Number Of Preferred Cells
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Abbreviated name
noOfPrefCells
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the maximum
number of preferred cell identifiers that the BSC
sends to the MSC in the HANDOVER_ REQUIRED
message.
Additional information
-
Range
1...16
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
3
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
-
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
•
3GPP Reference: 48.008
MML Commands
EEM. EEO
MML Abbreviated Name
NPC
MML Full Name
number of preferred cells
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 418
DN9813866
Base Station Controller (BSC) radio network object parameters
Number Of Preferred Cells (Cont.)
Id:0900d8058089b05f
Confidential
585
Base Station Controller (BSC) radio network object parameters
9.226
BSS Radio Network Parameter Dictionary
penalty trigger measurement period (PTMP)
Parameter name
Penalty Trigger Measurement Period
Abbreviated name
triggerMeasPeriod
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the length of the period
during which the latest Inter-System Handover counters
are used, if the WCDMA RAN Service Area and neighbour WCDMA RAN cell penalty triggering are used.
According to the value of this parameter, the BSC calculates how many successful incoming Inter-System Handovers have occurred per each Service Area and how
many unsuccessful outgoing inter-system handover
attempts have occurred per each neighbour WCDMA
RAN cell during the latest measurement period.
Note for MML:
range:
2...254 (seconds) by 2 second steps OR N
special value N = WCDMA RAN service area and neighbour WCDMA RAN cell penalty triggering is disabled
Additional information
-
Range
2...254
Step
2
Unit
seconds
Formula for getting internal
value
internal_value = gui_value
Default value
128 seconds
Default value notes
-
Required on Creation
optional
Special value
Disabled (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
Inter System HO (ISHO Support In BSC) (56)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
Table 419
586
•
Penalty Trigger Measurement Period
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Abbreviated Name
PTMP
MML Full Name
penalty trigger measurement period
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 419
9.227
PFC ack BLER limit for transfer delay 1 (ABL1)
Parameter name
PFC Ack BLER Limit For Transfer Delay 1
Abbreviated name
pfcAckBlerLimit_notAvailable
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the maximum block error
rate for PFCs for which the transfer delay is not available.
This parameter is only valid for a PCU supporting EQoS
feature.
Additional information
-
Range
0...100
Step
1
Unit
%
Formula for getting internal
value
internal_value = gui_value
Default value
90 %
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
BSS11111: Enhanced Quality of Service, EQoS
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEV, EEO
Table 420
DN9813866
Penalty Trigger Measurement Period (Cont.)
PFC Ack BLER Limit For Transfer Delay 1
Id:0900d8058089b05f
Confidential
587
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Abbreviated Name
ABL1
MML Full Name
PFC ack BLER limit for transfer delay 1
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 420
9.228
PFC unack BLER limit for SDU error ratio 1 (UBL1)
Parameter name
PFC Unack BLER Limit For SDU Error Ratio 1
Abbreviated name
pfcUnackBlerLimit_notAvailable
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the maximum block error
rate for PFCs for which the SDU Error Ratio is not available. This parameter is only valid for a PCU supporting
EQoS feature.
Additional information
-
Range
0...250
Step
1
Unit
per mil
Formula for getting internal
value
internal_value = gui_value
Default value
20 per mil
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
BSS11111: Enhanced Quality of Service, EQoS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEV, EEO
Table 421
588
PFC Ack BLER Limit For Transfer Delay 1 (Cont.)
PFC Unack BLER Limit For SDU Error Ratio 1
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Abbreviated Name
UBL1
MML Full Name
PFC unack BLER limit for SDU error ratio 1
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 421
9.229
PFC Unack BLER Limit For SDU Error Ratio 1 (Cont.)
pre-emption usage in handover (PRE)
Parameter name
Pre-Emption Usage In Handover
Abbreviated name
preemptionUsageInHO
Managed object
BSC
Multiplicity
1
Description
With this parameter you define if the pre-emption feature
is applied or not in handovers.
Additional information
-
Range
the pre-emption is not applied in handover (N) (0), the
pre-emption is applied in handover (Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
the pre-emption is not applied in handover (N) ==> 0
the pre-emption is applied in handover (Y) ==> 1
Default value
the pre-emption is applied in handover (Y) (1)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
Preempt Usage In BSC (68)
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
PRE
Table 422
DN9813866
•
Pre-Emption Usage In Handover
Id:0900d8058089b05f
Confidential
589
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Full Name
pre-emption usage in handover
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 422
9.230
precise paging enabled for repagings (PRECRP)
Parameter name
Precise Paging Enabled For Repagings
Abbreviated name
precPageEnRepage
Managed object
BSC
Multiplicity
1
Description
With this parameter operator defines shall BSC use
Precise Pagings also for repagings. If disabled Precise
Paging is used next time for the MS after the MS’s
location has been updated to BSCs location database.
That can happen only when the MS has connection to
BSC. When this parameter is disabled there may be a
need to adjust repaging delay in the MSC and the SGSN.
Additional information
-
Range
Disabled (0), Enabled (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internalDisabled ==> 0Enabled ==> 1
Default value
Enabled (1)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Precise Paging (168)
Related features
•
BSS21335 Precise Paging
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EEQ
MML Abbreviated Name
PRECRP
Table 423
590
Pre-Emption Usage In Handover (Cont.)
Precise Paging Enabled For Repagings
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
MML Full Name
precise paging enabled for repagings
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 423
9.231
precise paging expanding delay (PRECPD)
Parameter name
Precise Paging Expanding Delay
Abbreviated name
precPageExpandDelay
Managed object
BSC
Multiplicity
1
Description
With this parameter operator defines the delay after the
paging is expanded to rest of the cells in the paging area
when the MS is first Precise Paged.
Additional information
-
Range
2...8
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
2
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Precise Paging (168)
Related features
•
BSS21335 Precise Paging
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EEQ
MML Abbreviated Name
PRECPD
MML Full Name
precise paging expanding delay
Segment Level Parameter
-
Table 424
DN9813866
Precise Paging Enabled For Repagings (Cont.)
Precise Paging Expanding Delay
Id:0900d8058089b05f
Confidential
591
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 424
9.232
precise paging MSC repaging delay (PRECMD)
Parameter name
Precise Paging MSC Repaging Delay
Abbreviated name
precPageMscDel
Managed object
BSC
Multiplicity
1
Description
With this parameter operator defines the delay value
used for repaging in MSC. The parameter defines for how
long time the BSC has to save TMSI from previous
paging attempt to be used for possible next repaging
attempt. This parameter has effect only when Precise
Paging is enabled.
Additional information
-
Range
1...10
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
5
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Precise Paging (168)
Related features
•
BSS21335 Precise Paging
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EEQ
MML Abbreviated Name
PRECMD
MML Full Name
precise paging MSC repaging delay
Segment Level Parameter
-
Table 425
592
Precise Paging Expanding Delay (Cont.)
Precise Paging MSC Repaging Delay
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 425
9.233
Precise Paging MSC Repaging Delay (Cont.)
precise paging location records living time (PRECPL)
Parameter name
Precise Paging Location Records Living Time
Abbreviated name
precPageRecLife
Managed object
BSC
Multiplicity
1
Description
With this parameter operator defines how long BSC is
allowed to use a location record of a MS for Precise
Paging after creation or last update.
Additional information
-
Range
1...24
Step
1
Unit
h
Formula for getting internal
value
internal_value = gui_value
Default value
24
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Precise Paging (168)
Related features
•
BSS21335 Precise Paging
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EEQ
MML Abbreviated Name
PRECPL
MML Full Name
precise paging location records living time
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 426
DN9813866
Precise Paging Location Records Living Time
Id:0900d8058089b05f
Confidential
593
Base Station Controller (BSC) radio network object parameters
9.234
BSS Radio Network Parameter Dictionary
precise paging TMSI optimization (PRECTO)
Parameter name
Precise Paging TMSI Optimization
Abbreviated name
precPageTmsiOpt
Managed object
BSC
Multiplicity
1
Description
With this parameter operator defines shall BSC convert
repagings received with IMSI to TMSI pagings when possible. This feature should be disabled if MSC is configured to send repaging with TMSI.
Additional information
-
Range
Disabled (0), Enabled (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internalDisabled ==> 0Enabled ==> 1
Default value
Disabled (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Precise Paging (168)
Related features
•
BSS21335 Precise Paging
Interfaces
•
•
BSC <-> RAC
RAC <-> RACApp
References
-
MML Commands
EEQ
MML Abbreviated Name
PRECTO
MML Full Name
precise paging TMSI optimization
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 427
594
Precise Paging TMSI Optimization
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.235
Base Station Controller (BSC) radio network object parameters
priority level (PR)
Parameter name
Priority Level
Abbreviated name
pieToSubscriber
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the priority level to which
a certain subscriber type is to be attached.
Additional information
-
Range
0...14
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
pieToSubscriberType of BSC - If parameter is given, then
parameter Subscriber Type is obligatory.
Parameter relationships
-
•
Related options
Improved Trunk Reservation (19)
Related features
-
Interfaces
-
References
-
MML Commands
EET
MML Abbreviated Name
PR
MML Full Name
priority level
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 428
9.236
PSE overload alarm threshold (POAT)
Parameter name
PSE Overload Alarm Threshold
Abbreviated name
pseOverlAlarmThresh
Table 429
DN9813866
Priority Level
PSE Overload Alarm Threshold
Id:0900d8058089b05f
Confidential
595
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Managed object
BSC
Multiplicity
1
Description
Threshold for the PSE overloaded alarm. With this
parameter you can change the response of the alarm.
The smaller the value of this parameter is, the more sensitive the BSC is to set the alarm.
Additional information
-
Range
20...100
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
75
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Packet Control Unit (PCU2) pooling (97)
Related features
•
BSS20106: Packet Control Unit (PCU2) pooling
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEQ
MML Abbreviated Name
POAT
MML Full Name
PSE overload alarm threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 429
9.237
PSE PCU selection algorithm threshold (PSAT)
Parameter name
PSE PCU Selection Algorithm Threshold
Abbreviated name
pcuSelectionThresh
Managed object
BSC
Multiplicity
1
Table 430
596
PSE Overload Alarm Threshold (Cont.)
PSE PCU Selection Algorithm Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Description
Threshold for the PCU selection algorithm. With this
parameter you can change the behavior of the PCU
selection algorithm. The smaller the value of this parameter is, the more sensitive the algorithm is to move
cells/DAPs.
Additional information
-
Range
20...95
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
65
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Packet Control Unit (PCU2) pooling (97)
Related features
•
BSS20106: Packet Control Unit (PCU2) pooling
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEQ
MML Abbreviated Name
PSAT
MML Full Name
PSE PCU selection algorithm threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 430
9.238
public served count (PSC)
Parameter name
Public Served Count
Abbreviated name
publicServCount
Managed object
BSC
Multiplicity
1
Table 431
DN9813866
PSE PCU Selection Algorithm Threshold (Cont.)
Public Served Count
Id:0900d8058089b05f
Confidential
597
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Description
With this parameter you define how many public users
must be served before a WPS user can be served. This
parameter is applied in traffic channel allocation when the
WPS users already have WPS priority capacity in use
and more than WPS preference capacity of the rest of the
cell's resources are in use. Value 0 indicates that all the
idle resources of a cell can be allocated to successive
WPS calls without any restrictions.
Additional information
-
Range
0...10
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
3
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
-
•
•
Interfaces
Wireless Priority Service (WPS) In Use In BSC (71)
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ,EEO
MML Abbreviated Name
PSC
MML Full Name
public served count
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 431
9.239
packet loss timer duration start reaction (PLTON)
Parameter name
Packet Loss Timer Duration Start Reaction
Abbreviated name
packetLossTimerDurStartReact
3GPP name
-
Table 432
598
Public Served Count (Cont.)
Packet Loss Timer Duration Start Reaction
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the timer of the
period when the related Packet Loss congestion
has to be present in order to be defined as
"detected". It is related to average window concerning congestion algorithm.
NOTE:
The values of these timers are valid both for UL and
for DL direction.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
1...300
Step
1
Units
s
Formula for getting
internal value
internal_value =gui_value
Default value
10
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
PLTON
MML Commands
EEY, EEO
Table 432
DN9813866
Packet Loss Timer Duration Start Reaction (Cont.)
Id:0900d8058089b05f
Confidential
599
Base Station Controller (BSC) radio network object parameters
MML Full Name
packet loss timer duration start reaction
Segment Level Parameter
-
Table 432
9.240
BSS Radio Network Parameter Dictionary
Packet Loss Timer Duration Start Reaction (Cont.)
packet loss timer duration stop reaction (PLTOFF)
Parameter name
Packet Loss Timer Duration Stop Reaction
Abbreviated name
packetLossTimerDurStopReact
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
This timer defines the period when the related
Packet Loss congestion has to be absent in order
to be defined as "not detected". It is related to
average window concerning congestion algorithm.
NOTE:
The values of these timers are valid both for UL and
for DL direction.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
1...1000
Step
1
Units
s
Formula for getting
internal value
internal_value =gui_value
Default value
100
Default value notes
-
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 433
600
Packet Loss Timer Duration Stop Reaction
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
PLTOFF
MML Commands
EEY, EEO
MML Full Name
packet loss timer duration stop reaction
Segment Level Parameter
-
Table 433
9.241
Packet Loss Timer Duration Stop Reaction (Cont.)
PS packet drop period (PSPDP)
Parameter name
PS Packet Drop Period
Abbreviated name
psPacketDropPeriod
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter user defined the packet drop
period for PS packets.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types.
Additional information
-
Range
0...100
Step
1
Units
ms
Formula for getting
internal value
internal_value =gui_value
Default value
25
Default value notes
-
Required on creation
optional
Table 434
DN9813866
PS Packet Drop Period
Id:0900d8058089b05f
Confidential
601
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Child parameters
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
PSPDP
MML Commands
EEY, EEO
MML Full Name
PS packet drop period
Segment Level Parameter
-
Table 434
9.242
PS Packet Drop Period (Cont.)
PS UDP-MUX port (PSUMP)
Parameter name
PS UDP-MUX Port
Abbreviated name
psUdpMuxPort
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you identify the Packet Abis
user datagram protocol (UDP) MUX port number
for PS U-plane.
The configured value for "PS UDP-Mux Port" shall
be different from the one configured for "CS UDPMux Port" and from all other UDP ports reserved for
e.g. Traceroute.
NOTE:
Parameter is valid only for Flexi EDGE and Flexi
Multiradio site types
Table 435
602
PS UDP-MUX Port
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Additional information
-
Range
49152...65534
Step
2
Units
-
Formula for getting
internal value
internal_value =gui_value
Default value
49154
Default value notes
-
Special value
Not defined (65535)
Required on creation
optional
Child parameters
-
Modification
On-Line
Modified
Parameter is updated to functioning in certain BCF
of the BSC when BCF is next time reset after
parameter modification. When modified by FBPP
updating to BCF is made to all BCFs of the BSC.
Related parameters
csUdpMuxPort of BSC - This parameter value has
to be defined different than PS UDP-Mux Port.
Parameter relationships
-
Related options
Packet Abis over IP/Eth (150) or
Packet Abis over TDM (151)
Feature dependencies
BSS21440: Packet Abis over TDM
BSS21454: Packet Abis over IP/Eth
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
PSUMP
MML Commands
EEY, EEO
MML Full Name
PS UDP-MUX port
Segment Level Parameter
-
Table 435
DN9813866
PS UDP-MUX Port (Cont.)
Id:0900d8058089b05f
Confidential
603
Base Station Controller (BSC) radio network object parameters
9.243
BSS Radio Network Parameter Dictionary
QC NCCR action trigger threshold (QCATN)
Parameter name
QC NCCR Action Trigger Threshold
Abbreviated name
qcActionTriggerThr_nccr
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the Quality Control NCCR
action trigger threshold.
Additional information
-
Range
0...1000
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
100
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
BSS11111: Enhanced Quality of Service, EQoS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEV, EEO
MML Abbreviated Name
QCATN
MML Full Name
QC NCCR action trigger threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 436
604
QC NCCR Action Trigger Threshold
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.244
Base Station Controller (BSC) radio network object parameters
QC reallocation action trigger threshold (QCATR)
Parameter name
QC Reallocation Action Trigger Threshold
Abbreviated name
qcActionTriggerThr_realloca
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the Quality Control reallocation action trigger threshold.
Additional information
-
Range
0...1000
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
25
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
BSS11111: Enhanced Quality of Service, EQoS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEV, EEO
MML Abbreviated Name
QCATR
MML Full Name
QC reallocation action trigger threshold
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 437
DN9813866
QC Reallocation Action Trigger Threshold
Id:0900d8058089b05f
Confidential
605
Base Station Controller (BSC) radio network object parameters
9.245
BSS Radio Network Parameter Dictionary
RNC to SPC mapping info (RNC)
Parameter name
RNC to SPC
Abbreviated name
rncToSpc
Managed object
BSC
Multiplicity
16
Description
RNC identification mapping to the signaling point
code in the Iur-g interface
Additional information
-
Child parameters
•
•
Formula for getting
internal value
-
Default value
-
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
•
Load reporting via Iur-g (FC 1824) (optional)
OR
ISHO acceleration via Iur-g (FC 1825)
(optional)
Related features
•
•
BSS21527: Load reporting via Iur-g (standard)
BSS21528: ISHO acceleration via Iur-g (standard)
Interfaces
•
BSC <-> RNC
References
•
NSN reference: BSS21527: Load reporting to
TD-RNC over Iur-G
MML Commands
EEO
MML Abbreviated Name
RNC
MML Full Name
RNC to SPC mapping info
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 438
606
rncId
spc
RNC to SPC mapping info
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.246
Base Station Controller (BSC) radio network object parameters
RNC ID (RNCID)
Parameter name
RNC ID
Abbreviated name
rncId
Managed object
BSC
Multiplicity
1
Description
The radio network controller that is connected to
certain signaling point code in the Iur-g interface
Additional information
-
Range
1...4095
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
65535
Default value notes
not used
Required on Creation
optional
Special value
Not used (65536)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
•
Related features
•
•
BSS21527: Load reporting via Iur-g (standard)
BSS21528: ISHO acceleration via Iur-g (standard)
Interfaces
•
BSC <-> RNC
References
•
NSN reference: BSS21527: Load reporting to
TD-RNC over Iur-G
MML Commands
EEN,EEO
MML Abbreviated Name
RNCID
MML Full Name
RNC ID
Segment Level Parameter
-
Table 439
DN9813866
Load reporting via Iur-g (FC 1824) (optional)
OR
ISHO acceleration via Iur-g (FC 1825)
(optional)
RNC ID
Id:0900d8058089b05f
Confidential
607
Base Station Controller (BSC) radio network object parameters
File Based Provisioning
supported
Table 439
9.247
BSS Radio Network Parameter Dictionary
false
RNC ID (Cont.)
RNW configuration Identification (RNW ID)
Parameter name
RNW Configuration Identification
Abbreviated name
rnwConfId
Managed object
BSC
Multiplicity
1
Description
RNW Configuration Identification identifies the active
configuration. It is copied from Plan Configuration Identification in activation phase.
Additional information
-
Range
1...2147483647
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Special value
Not defined (0)
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS20012: File Based RNW Plan Provisioning
Interfaces
•
RAC <-> BSC
References
-
MML Commands
EEE
MML Abbreviated Name
RNW ID
MML Full Name
RNW configuration Identification
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 440
608
RNW Configuration Identification
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.248
Base Station Controller (BSC) radio network object parameters
RNW fallback configuration identification (FB ID)
Parameter name
RNW Fallback Configuration Identification
Abbreviated name
rnwFallbackConfId
Managed object
BSC
Multiplicity
1
Description
RNW Fallback Configuration Identification identifies the
fallback configuration. It is copied from RNW Plan Configuration Identification in activation phase.
When fallback activation is started, RNW Fallback Configuration Identification is used to check that operator
gives right identification of fallback.
Additional information
-
Range
1...2147483647
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Special value
Not defined (0)
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS20012: File Based RNW Plan Provisioning
Interfaces
•
RAC <-> BSC
References
-
MML Commands
EEE
MML Abbreviated Name
FB ID
MML Full Name
RNW fallback configuration identification
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 441
DN9813866
RNW Fallback Configuration Identification
Id:0900d8058089b05f
Confidential
609
Base Station Controller (BSC) radio network object parameters
9.249
BSS Radio Network Parameter Dictionary
RNW plan configuration identification (PLAN ID)
Parameter name
RNW Plan Configuration Identification
Abbreviated name
rnwPlanConfId
Managed object
BSC
Multiplicity
1
Description
With this parameter you identify RNW Plan Configuration.
RNW Configuration Identification for plan database is
defined when plan is downloaded.
When plan validation, activation or interruption is started
by operator, RNW Plan Configuration Identifigation is
used to check that operator gives right identification of
plan.
Additional information
-
Range
1...2147483647
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Special value
Not defined (0)
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
•
BSS20012: File Based RNW Plan Provisioning
Interfaces
•
RAC <-> BSC
References
-
MML Commands
EEE
MML Abbreviated Name
PLAN ID
MML Full Name
RNW plan configuration identification
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 442
610
RNW Plan Configuration Identification
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.250
Base Station Controller (BSC) radio network object parameters
RNW plan database state
Parameter name
RNW Plan Database State
Abbreviated name
rnwPlanDatabaseState
Managed object
BSC
Multiplicity
1
Description
Parameter defines the state of the RNW plan database. State information is available only for the
RNW plan database.
States for the RNW plan database are:
CLEAR (RNW plan does not exist)
DOWNLOADING (download is ongoing)
DOWNLOAD_INIT (initialization of RNW Plan
database is ongoing)
DOWNLOADED ( RNW plan is downloaded;
database is initialized and changes of the plan are
made to database)
VALIDATING (validation of the plan database is
ongoing)
VALIDATING_NO_INT (validation of the plan
database is ongoing, BSC Radio Network configuration changes are denied)
VALIDATED (validation is done; RNW plan
database is ready to be activated)
ACTIVATING (activation of the plan database is
ongoing)
ACTIVATED (RNW plan is activated)
INTERRUPTED (activation is interrupted by operator)
FALLBACK_ACT (fallback activation ongoing)
ACT_INIT (fallback copy is dumped to disk)
FALLBACK_INIT (fallback copy is loaded to
memory)
INTERRUPTED_BY_SYSTEM (activation interrupted by system; only fallback activation allowed in
that state)
Additional information
Table 443
DN9813866
-
RNW Plan Database State
Id:0900d8058089b05f
Confidential
611
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Range
CLEAR (0), DOWNLOADING (1),
DOWNLOAD_INIT (2), DOWNLOADED (3), VALIDATING (4), VALIDATING_NO_INT (5), VALIDATED (6), ACTIVATING (7), ACTIVATED (8),
INTERRUPTED (9), FALLBACK_ACT (10),
ACT_INIT (11), FALLBACK_INIT (12),
INTERRUPTED_BY_SYSTEM (13)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
CLEAR ==> 0
DOWNLOADING ==> 1
DOWNLOAD_INIT ==> 2
DOWNLOADED ==> 3
VALIDATING ==> 4
VALIDATING_NO_INT ==> 5
VALIDATED ==> 6
ACTIVATING ==> 7
ACTIVATED ==> 8
INTERRUPTED ==> 9
FALLBACK_ACT ==> 10
ACT_INIT ==> 11
FALLBACK_INIT ==> 12
INTERRUPTED_BY_SYSTEM ==> 13
Default value
CLEAR (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
Not modifiable
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
BSS20012: File Based RNW Plan Provisioning
Interfaces
•
BSC -> RAC
References
-
MML Commands
EEK, EEE
Table 443
612
RNW Plan Database State (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
MML Abbreviated Name
-
MML Full Name
RNW plan database state
Segment Level Parameter
-
File Based Provisioning
supported
false
Table 443
9.251
RNW Plan Database State (Cont.)
RX antenna supervision period (RXANT)
Parameter name
RX Antenna Supervision Period
Abbreviated name
rxAntSupPer
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the time, in minutes, that
the BTS uses for the internal RX antenna supervision.
Additional information
-
Range
15...65534
Step
1
Unit
min
Formula for getting internal
value
internal_value = gui_value
Default value
65535 min
Default value notes
-
Required on Creation
mandatory
Special value
internal supervision is not performed (65535)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
RXANT
Table 444
DN9813866
Base Station Controller (BSC) radio network object parameters
RX Antenna Supervision Period
Id:0900d8058089b05f
Confidential
613
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
MML Full Name
RX antenna supervision period
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 444
9.252
RX Antenna Supervision Period (Cont.)
RX level balance (RXBAL)
Parameter name
RX Level Balance
Abbreviated name
rxLevBalance
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the balance between the
downlink signal level and the uplink signal level within the
BSC coverage area. Value 5 dB means that the downlink
signal is 5 dB stronger than the uplink signal.
Additional information
-
Range
0...20
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
5 dB
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Related features
-
•
•
Interfaces
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
RXBAL
MML Full Name
RX level balance
Segment Level Parameter
-
Table 445
614
RAC <-> RACApp
RAC <-> BSC
RX Level Balance
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
File Based Provisioning sup- true
ported
Table 445
9.253
RX Level Balance (Cont.)
RX level based TCH access (RXTA)
Parameter name
RX Level Based TCH Access
Abbreviated name
rxLevelBasedTchAccess
Managed object
BSC
Multiplicity
1
Description
This parameter is used to determine whether TCH
access is based on downlink RX level.
NOTE:
MML range:
0 = RX level based TCH access is not used
1 = RX level based TCH access is used in call setup
2 = RX level based TCH access is used in call setup
and in handovers
Additional information
-
Range
Not Used (0), Used In Call Setup (1), Used In Call
Setup And In Handovers (2)
Step
-
Unit
-
Formula for getting
internal value
gui ==> internal
Not Used ==> 0
Used In Call Setup ==> 1
Used In Call Setup And In Handovers ==> 2
Default value
Not Used (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
Table 446
DN9813866
BSS20002: Cingular 38 RxLev Min Access
RX Level Based TCH Access
Id:0900d8058089b05f
Confidential
615
Base Station Controller (BSC) radio network object parameters
Interfaces
•
•
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
RXTA
MML Full Name
RX level based TCH access
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 446
9.254
RAC <-> RACApp
RAC <-> BSC
RX Level Based TCH Access (Cont.)
RX quality limit MS multislot pwr prof 0 with 2 UL TSL
(RL02)
Parameter name
RX Quality Limit MS Multislot Pwr Prof 0 With 2 UL TSL
Abbreviated name
rxqualLimitUL_Prof0_2tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the RX quality limit for MS multislot power profile 0 when allocating 2 uplink TSLs. The
measured RX quality value is compared to the value of
this parameter when defining how many uplink TSLs can
be allocated. If the RX quality limit is set high, power
reduction is not taken into account so strictly in channel
allocation.
Additional information
-
Range
0...8
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
5 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 447
616
BSS Radio Network Parameter Dictionary
RX Quality Limit MS Multislot Pwr Prof 0 With 2 UL TSL
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
RL02
MML Full Name
RX quality limit MS multislot pwr prof 0 with 2 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 447
9.255
RX quality limit MS multislot pwr prof 0 with 3 UL TSL
(RL03)
Parameter name
RX Quality Limit MS Multislot Pwr Prof 0 With 3 UL TSL
Abbreviated name
rxqualLimitUL_Prof0_3tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the RX quality limit for MS multislot power profile 0 when allocating 3 uplink TSLs. The
measured RX quality value is compared to the value of
this parameter when defining how many uplink TSLs can
be allocated. If the RX quality limit is set high, power
reduction is not taken into account so strictly in channel
allocation.
Additional information
-
Range
0...8
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
3 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Table 448
DN9813866
RX Quality Limit MS Multislot Pwr Prof 0 With 2 UL TSL (Cont.)
RX Quality Limit MS Multislot Pwr Prof 0 With 3 UL TSL
Id:0900d8058089b05f
Confidential
617
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
RL03
MML Full Name
RX quality limit MS multislot pwr prof 0 with 3 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 448
9.256
RX quality limit MS multislot pwr prof 0 with 4 UL TSL
(RL04)
Parameter name
RX Quality Limit MS Multislot Pwr Prof 0 With 4 UL
TSL
Abbreviated name
rxqualLimitUL_Prof0_4tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the RX quality limit for MS
multislot power profile 0 when allocating 4 uplink
TSLs. The measured RX quality value is compared
to the value of this parameter when defining how
many uplink TSLs can be allocated. If the RX
quality limit is set high, power reduction is not taken
into account so strictly in channel allocation.
Additional information
-
Range
0...8
Step
1
Unit
dB
Table 449
618
RX Quality Limit MS Multislot Pwr Prof 0 With 3 UL TSL (Cont.)
RX Quality Limit MS Multislot Pwr Prof 0 With 4 UL TSL
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
internal_value = gui_value
Default value
1 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in
BSC) (39) (optional) OR Enhanced GPRS
(EGPRS) Usage (51) (optional)
Feature dependencies
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
RL04
MML Full Name
RX quality limit MS multislot pwr prof 0 with 4 UL
TSL
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 449
9.257
RX Quality Limit MS Multislot Pwr Prof 0 With 4 UL TSL (Cont.)
RX quality limit MS multislot pwr prof 1 with 2 UL TSL
(RL12)
Parameter name
RX Quality Limit MS Multislot Pwr Prof 1 With 2 UL
TSL
Abbreviated name
rxqualLimitUL_Prof1_2tsl
Managed object
BSC
Multiplicity
1
Table 450
DN9813866
Base Station Controller (BSC) radio network object parameters
RX Quality Limit MS Multislot Pwr Prof 1 With 2 UL TSL
Id:0900d8058089b05f
Confidential
619
Base Station Controller (BSC) radio network object parameters
Description
This parameter indicates the RX quality limit for MS
multislot power profile 1 when allocating 2 uplink
TSLs. The measured RX quality value is compared
to the value of this parameter when defining how
many uplink TSLs can be allocated. If the RX
quality limit is set high, power reduction is not taken
into account so strictly in channel allocation.
Additional information
-
Range
0...8
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
5 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in
BSC) (39) (optional) OR Enhanced GPRS
(EGPRS) Usage (51) (optional)
Feature dependencies
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
RL12
MML Full Name
RX quality limit MS multislot pwr prof 1 with 2 UL
TSL
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 450
620
BSS Radio Network Parameter Dictionary
RX Quality Limit MS Multislot Pwr Prof 1 With 2 UL TSL (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.258
RX quality limit MS multislot pwr prof 1 with 3 UL TSL
(RL13)
Parameter name
RX Quality Limit MS Multislot Pwr Prof 1 With 3 UL TSL
Abbreviated name
rxqualLimitUL_Prof1_3tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the RX quality limit for MS multislot power profile 1 when allocating 3 uplink TSLs. The
measured RX quality value is compared to the value of
this parameter when defining how many uplink TSLs can
be allocated. If the RX quality limit is set high, power
reduction is not taken into account so strictly in channel
allocation.
Additional information
-
Range
0...8
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
3 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
RL13
MML Full Name
RX quality limit MS multislot pwr prof 1 with 3 UL TSL
Segment Level Parameter
-
Table 451
DN9813866
Base Station Controller (BSC) radio network object parameters
RX Quality Limit MS Multislot Pwr Prof 1 With 3 UL TSL
Id:0900d8058089b05f
Confidential
621
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 451
9.259
RX quality limit MS multislot pwr prof 1 with 4 UL TSL
(RL14)
Parameter name
RX Quality Limit MS Multislot Pwr Prof 1 With 4 UL
TSL
Abbreviated name
rxqualLimitUL_Prof1_4tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the RX quality limit for MS
multislot power profile 1 when allocating 4 uplink
TSLs. The measured RX quality value is compared
to the value of this parameter when defining how
many uplink TSLs can be allocated. If the RX
quality limit is set high, power reduction is not taken
into account so strictly in channel allocation.
Additional information
-
Range
0...8
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
1 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in
BSC) (39) (optional) OR Enhanced GPRS
(EGPRS) Usage (51) (optional)
Feature dependencies
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Table 452
622
RX Quality Limit MS Multislot Pwr Prof 1 With 3 UL TSL (Cont.)
RX Quality Limit MS Multislot Pwr Prof 1 With 4 UL TSL
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Interfaces
•
•
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
RL14
MML Full Name
RX quality limit MS multislot pwr prof 1 with 4 UL
TSL
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 452
9.260
RACApp <-> RAC
RAC <-> BSC
RX Quality Limit MS Multislot Pwr Prof 1 With 4 UL TSL (Cont.)
RX quality limit MS multislot pwr prof 2 with 3 UL TSL
(RL23)
Parameter name
RX Quality Limit MS Multislot Pwr Prof 2 With 3 UL TSL
Abbreviated name
rxqualLimitUL_Prof2_3tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the RX quality limit for MS multislot power profile 2 when allocating 3 uplink TSLs. The
measured RX quality value is compared to the value of
this parameter when defining how many uplink TSLs can
be allocated. If the RX quality limit is set high, power
reduction is not taken into account so strictly in channel
allocation.
Additional information
-
Range
0...8
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
3 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Table 453
DN9813866
Base Station Controller (BSC) radio network object parameters
RX Quality Limit MS Multislot Pwr Prof 2 With 3 UL TSL
Id:0900d8058089b05f
Confidential
623
Base Station Controller (BSC) radio network object parameters
Parameter relationships
BSS Radio Network Parameter Dictionary
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
RL23
MML Full Name
RX quality limit MS multislot pwr prof 2 with 3 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 453
9.261
RX quality limit MS multislot pwr prof 2 with 4 UL TSL
(RL24)
Parameter name
RX Quality Limit MS Multislot Pwr Prof 2 With 4 UL TSL
Abbreviated name
rxqualLimitUL_Prof2_4tsl
Managed object
BSC
Multiplicity
1
Description
This parameter indicates the RX quality limit for MS multislot power profile 2 when allocating 4 uplink TSLs. The
measured RX quality value is compared to the value of
this parameter when defining how many uplink TSLs can
be allocated. If the RX quality limit is set high, power
reduction is not taken into account so strictly in channel
allocation.
Additional information
-
Range
0...8
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
2 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Table 454
624
RX Quality Limit MS Multislot Pwr Prof 2 With 3 UL TSL (Cont.)
RX Quality Limit MS Multislot Pwr Prof 2 With 4 UL TSL
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
BSC GPRS Param Enabled (GPRS O&M in BSC)
(39) (optional) OR Enhanced GPRS (EGPRS)
Usage (51) (optional)
Related features
•
•
BSS20089: Extended Dynamic Allocation
BSS20084: High Multislot Classes
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEJ, EEO
MML Abbreviated Name
RL24
MML Full Name
RX quality limit MS multislot pwr prof 2 with 4 UL TSL
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 454
9.262
RX Quality Limit MS Multislot Pwr Prof 2 With 4 UL TSL (Cont.)
SACCH repeat window (SRW)
Parameter name
SACCH Repeat Window
Abbreviated name
sacchRepeatWindow
Managed object
BSC
Multiplicity
1
Description
This parameter defines when the BTS commands an MS
to repeat the SACCH block.
If the parameter has value 1, decoding failure of the latest
SACCH block triggers the repeat for the next SACCH
block.
If the parameter has value N = {2, 3, 4 .. 15}, decoding
failure of 2 SACCH blocks out of N preceding SACCH
blocks triggers the repeat. Repeat is used as long as the
decoding of 2 SACCH blocks out of N preceding blocks
has failed.
Additional information
-
Range
1...15
Step
1
Unit
Frames
Table 455
DN9813866
SACCH Repeat Window
Id:0900d8058089b05f
Confidential
625
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Formula for getting internal
value
internal_value = gui_value
Default value
4 Frames
Default value notes
-
Required on Creation
mandatory
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
Robust AMR Signalling / FACCH and SACCH repetition (109)
Related features
•
BSS20872: Robust AMR Signalling
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEO, EEQ
MML Abbreviated Name
SRW
MML Full Name
SACCH repeat window
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 455
9.263
SAIC DL C/I offset (SCIO)
Parameter name
SAIC DL C/I Offset
Abbreviated name
saicDlCIOffset
Managed object
BSC
Multiplicity
1
Description
This parameter defines how much lower downlink
C/I values can be used for SAIC calls than for nonSAIC calls in DFCA TCH allocation.
Additional information
-
Range
0...63
Step
1
Unit
dB
Table 456
626
SACCH Repeat Window (Cont.)
SAIC DL C/I Offset
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Formula for getting
internal value
internal_value = gui_value
Default value
2 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Table 456
DN9813866
Base Station Controller (BSC) radio network object parameters
SAIC DL C/I Offset (Cont.)
Id:0900d8058089b05f
Confidential
627
Base Station Controller (BSC) radio network object parameters
Related parameters
BSS Radio Network Parameter Dictionary
dfcaAmrFrConnection_ciTarget of BSC - SAIC DL
C/I Offset defines how much lower C/I Target AMR
FR values can be used for SAIC calls than for nonSAIC calls in DFCA TCH allocation.
dfcaAmrFrConnection_softBlockingCi of BSC SAIC DL C/I Offset defines how much lower Soft
Blocking C/I AMR FR values can be used for SAIC
calls than for non-SAIC calls in DFCA TCH allocation.
dfca144Connection_ciTarget of BSC - SAIC DL C/I
Offset defines how much lower C/I Target 14.4
values can be used for SAIC calls than for nonSAIC calls in DFCA TCH allocation.
dfca144Connection_softBlockingCi of BSC - SAIC
DL C/I Offset defines how much lower Soft Blocking
C/I 14.4 values can be used for SAIC calls than for
non-SAIC calls in DFCA TCH allocation.
dfcaFrConnection_ciTarget of BSC - SAIC DL C/I
Offset defines how much lower C/I Target FR
values can be used for SAIC calls than for nonSAIC calls in DFCA TCH allocation.
dfcaFrConnection_softBlockingCi of BSC - SAIC
DL C/I Offset defines how much lower Soft Blocking
C/I FR values can be used for SAIC calls than for
non-SAIC calls in DFCA TCH allocation.
dfcaAmrHrConnection_ciTarget of BSC - SAIC DL
C/I Offset defines how much lower C/I Target AMR
HR values can be used for SAIC calls than for nonSAIC calls in DFCA TCH allocation.
dfcaAmrHrConnection_softBlockingCi of BSC SAIC DL C/I Offset defines how much lower Soft
Blocking C/I AMR HR values can be used for SAIC
calls than for non-SAIC calls in DFCA TCH allocation.
dfcaHrConnection_ciTarget of BSC - SAIC DL C/I
Offset defines how much lower C/I Target HR
values can be used for SAIC calls than for nonSAIC calls in DFCA TCH allocation.
dfcaHrConnection_softBlockingCi of BSC - SAIC
DL C/I Offset defines how much lower Soft Blocking
C/I HR values can be used for SAIC calls than for
non-SAIC calls in DFCA TCH allocation.
Parameter relationships
Table 456
628
-
SAIC DL C/I Offset (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70) (optional) AND Single
Antenna Interference Cancellation (SAIC) (92)
(optional)
Feature dependencies
•
BSS20082: Single Antenna Interference Cancellation
BSS11052: Dynamic Frequency and Channel
Allocation
•
Interfaces
•
•
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
SCIO
MML Full Name
SAIC DL C/I offset
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 456
9.264
SAIC DL C/I Offset (Cont.)
service area penalty time (SAPT)
Parameter name
Service Area Penalty Time
Abbreviated name
wcdmaRanSaiPenalty
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the duration of the
handover penalty timer which has been triggered for a
Service Area. While the Service Area penalty timer is on,
the BSC is not allowed to initiate an Inter-System
Handover attempt towards WCDMA RAN cells that
belong to the Service Area.
Additional information
-
Range
0...255
Step
1
Unit
s
Formula for getting internal
value
internal_value = gui_value
Default value
127 s
Default value notes
-
Table 457
DN9813866
RAC <-> RACApp
RAC <-> BSC
Service Area Penalty Time
Id:0900d8058089b05f
Confidential
629
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
Related features
•
-
•
•
Interfaces
Inter System HO (ISHO Support In BSC) (56)
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
SAPT
MML Full Name
service area penalty time
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 457
9.265
signalling point code (SPC)
Parameter name
Signalling Point Code
Abbreviated name
signallingPointCode
Managed object
BSC
Multiplicity
1
Description
With this parameter you define Signalling Point Code.
Additional information
-
Range
0...16777215
Step
1
Unit
-
Formula for getting internal
value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Table 458
630
Service Area Penalty Time (Cont.)
Signalling Point Code
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Related parameters
-
Parameter relationships
-
Related options
•
Multipoint A Interface for BSC (94)
Related features
•
BSS20092: Multipoint A Interface for BSC
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
E7I, E7A, E7D
MML Abbreviated Name
SPC
MML Full Name
signalling point code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 458
9.266
signaling point code (SPC)
Parameter name
Signaling Point Code
Abbreviated name
signalingPointCode
Managed object
BSC
Multiplicity
1 (scalar parameter)
Description
With this parameter you define the Signaling Point Code
that is connected to certain Radio Network Controller in
Iur-g interface.
Additional information
-
Range
0...16777215
Step
1
Unit
-
Formula for getting internal
value
internal_value = UI_value
Default value
0
Default value notes
0 (not used)
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Table 459
DN9813866
Signalling Point Code (Cont.)
Signaling Point Code
Id:0900d8058089b05f
Confidential
631
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Related options
•
•
Load reporting via Iur-g (FC 1824) (optional) OR
ISHO acceleration via Iur-g (FC 1825) (optional)
Related features
•
•
BSS21527: Load reporting via Iur-g (standard)
BSS21528: ISHO acceleration via Iur-g (standard)
Interfaces
•
BSC <-> RNC
References
NSN reference: BSS21527 - Load reporting via Iur-g
MML Commands
EEI, EEO
MML Abbreviated Name
SPC
MML Full Name
signaling point code
Segment Level Parameter
-
File Based Provisioning sup- false
ported
Table 459
9.267
signaling point code (SPC)
Parameter name
Signaling Point Code List
Abbreviated name
spcList
Managed object
SPC
Multiplicity
6
Description
With this parameter you define the signalling point
code which will be mapped with a location area
code.
Additional information
-
Range
1...16777215
Step
1
Unit
-
Formula for getting
internal value
internal_value = gui_value
Default value
-
Default value notes
-
Required on Creation
optional
Special value
Not used (0)
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Table 460
632
Signaling Point Code (Cont.)
Signaling Point Code List
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70)
Feature dependencies
•
BSS11052: Dynamic Frequency and Channel
Allocation
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEC, EEF, EES
MML Abbreviated Name
SPC
MML Full Name
signaling point code
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 460
9.268
Base Station Controller (BSC) radio network object parameters
Signaling Point Code List (Cont.)
slow AMR LA enabled (SAL)
Parameter name
Slow AMR LA Enabled
Abbreviated name
slowAmrLaEnabled
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the AMR link adaptation
(LA) mode within the BSS.
Additional information
-
Range
fast LA mode is used (N) (0), enable slow AMR LA mode
(Y) (1)
Step
-
Unit
-
Formula for getting internal
value
gui ==> internal
fast LA mode is used (N) ==> 0
enable slow AMR LA mode (Y) ==> 1
Default value
fast LA mode is used (N) (0)
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Table 461
DN9813866
Slow AMR LA Enabled
Id:0900d8058089b05f
Confidential
633
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
AMR FR (50) (optional) OR AMR HR (72) (optional)
OR Wideband AMR (133) (optional)
Related features
•
BSS20249: AMR FR Licence Control
Interfaces
•
•
RACApp <-> RAC
BSC <-> RAC
References
-
MML Commands
EEM, EEO
MML Abbreviated Name
SAL
MML Full Name
slow AMR LA enabled
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 461
9.269
Slow AMR LA Enabled (Cont.)
soft blocking C/I 14.4 (SBCI)
Parameter name
Soft Blocking C/I 14.4
Abbreviated name
dfca144Connection_softBlockingCi
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the minimum
acceptable C/I value for circuit switched data connections of 14.4 kbit/s.
NOTE: The parameter value must be equal to or
smaller than C/I target 14.4.
Value -20 dB means that soft blocking is disabled.
NOTE: MML modification:
Parameter is modifiable if options Dynamic Frequency And Channel Allocation (70) AND
(HSCSD_PRM OR PRM_144) are ON. Options
(HSCSD_PRM and PRM_144) are hidden in MML
and available if the operator has purchased the
feature.
Additional information
-
Range
-20...43
Step
1
Table 462
634
Soft Blocking C/I 14.4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
-20 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
activationState of BSC - The parameter value must
be equal to or smaller than C/I target 14.4.
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70) (optional) AND ( High
Speed Circuit Switched Data (HSCSD TCSM2) (25) (optional) OR Data 144 Usage
(69) (optional) )
Feature dependencies
•
BSS11052: Dynamic Frequency and Channel
Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
SBCI
MML Full Name
soft blocking C/I 14.4
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 462
9.270
Soft Blocking C/I 14.4 (Cont.)
Soft Blocking C/I AMR FR (SBAF)
Parameter name
Soft Blocking C/I AMR FR
Abbreviated name
dfcaAmrFrConnection_softBlockingCi
Managed object
BSC
Multiplicity
1
Table 463
DN9813866
Base Station Controller (BSC) radio network object parameters
Soft Blocking C/I AMR FR
Id:0900d8058089b05f
Confidential
635
Base Station Controller (BSC) radio network object parameters
Description
BSS Radio Network Parameter Dictionary
With this parameter you define the minimum
acceptable C/I value for full rate AMR and full rate
WB-AMR FR speech connections.
NOTE: The parameter value must be equal to or
smaller than C/I target AMR FR.
Value -20 dB means that soft blocking is disabled.
Additional information
-
Range
-20...43
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
-20 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70) (optional) AND ( AMR FR
(50) (optional) OR Wideband AMR (133)
(optional) )
Feature dependencies
•
•
•
BSS20960: Wideband AMR
BSS11052: Dynamic Frequency and Channel
Allocation
BSS20249: AMR FR Licence Control
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
SBAF
MML Full Name
Soft Blocking C/I AMR FR
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 463
636
Soft Blocking C/I AMR FR (Cont.)
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.271
Base Station Controller (BSC) radio network object parameters
soft blocking C/I AMR HR (SBAH)
Parameter name
Soft Blocking C/I AMR HR
Abbreviated name
dfcaAmrHrConnection_softBlockingCi
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the minimum acceptable
C/I value for half rate AMR speech connections.
NOTE: The parameter value must be equal to or smaller
than C/I target AMR HR.
Value -20 dB means that soft blocking is disabled.
Additional information
-
Range
-20...43
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
-20 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
activationState of BSC - The parameter value must be
equal to or smaller than C/I target AMR HR.
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70) (optional) AND AMR HR (72) (optional)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
SBAH
MML Full Name
soft blocking C/I AMR HR
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 464
DN9813866
Soft Blocking C/I AMR HR
Id:0900d8058089b05f
Confidential
637
Base Station Controller (BSC) radio network object parameters
9.272
BSS Radio Network Parameter Dictionary
soft blocking C/I FR (SBF)
Parameter name
Soft Blocking C/I FR
Abbreviated name
dfcaFrConnection_softBlockingCi
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the minimum acceptable
C/I value for full rate and EFR speech connections, and
for circuit switched data connections up to 9.6 kbit/s.
NOTE: The parameter value must be equal to or smaller
than C/I target FR.
Value -20 dB means that soft blocking is disabled.
Additional information
-
Range
-20...43
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
-20 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
activationState of BSC - The parameter value must be
equal to or smaller than C/I target FR.
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
SBF
MML Full Name
soft blocking C/I FR
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 465
638
Soft Blocking C/I FR
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
9.273
Base Station Controller (BSC) radio network object parameters
soft blocking C/I GPRS (SBGP)
Parameter name
DFCA Soft Blocking C/I GPRS
Abbreviated name
dfcaSoftBlockingCiGPRS
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the soft blocking C/I value
for GPRS connection on DFCA layer.
Note: DFCA C/I Target GPRS is also related to this
parameter, DFCA Soft Blocking C/I GPRS value should
be defined equal or smaller than value for DFCA C/I
Target GPRS.
Additional information
-
Range
-20...43
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
-20 dB
Default value notes
C/I blocking is disabled by default
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
DFCA Soft Blocking C/I GPRS value should be defined
equal or smaller than value for DFCA C/I Target GPRS.
Related parameters
dfcaCiTargetGPRS of BSC - DFCA C/I Target GPRS is
used for setting target C/I value for GPRS connection
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70) (optional) AND SDCCH and PS Data
Channels on DFCA TRX (136) (optional)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
BSS21161: SDCCH and PS Data Channels on
DFCA TRX
•
•
•
Interfaces
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
SBGP
MML Full Name
soft blocking C/I GPRS
Segment Level Parameter
-
Table 466
DN9813866
RACApp <-> RAC
RAC <-> BSC
DFCA Soft Blocking C/I GPRS
Id:0900d8058089b05f
Confidential
639
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
File Based Provisioning sup- true
ported
Table 466
9.274
DFCA Soft Blocking C/I GPRS (Cont.)
Soft Blocking C/I HR (SBH)
Parameter name
Soft Blocking C/I HR
Abbreviated name
dfcaHrConnection_softBlockingCi
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the minimum
acceptable C/I value for half rate speech connections.
NOTE: The parameter value must be equal to or
smaller than C/I target HR.
Value -20 dB means that soft blocking is disabled.
Additional information
-
Range
-20...43
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
-20 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
dfcaHrConnection_ciTarget of BSC - The parameter value must be equal to or smaller than C/I target
HR.
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation) Usage (70) (optional) AND Half Rate
(17) (optional)
Feature dependencies
•
BSS11052: Dynamic Frequency and Channel
Allocation
Table 467
640
Soft Blocking C/I HR
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Interfaces
•
•
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
SBH
MML Full Name
Soft Blocking C/I HR
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 467
9.275
RAC <-> RACApp
RAC <-> BSC
Soft Blocking C/I HR (Cont.)
soft blocking C/I OSC DFR (SBDFR)
Parameter name
Soft Blocking C/I OSC DFR
Abbreviated name
softBlockingCiOscDfr
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the minimum
acceptable C/I value for double full rate connections.
Additional information
-
Range
-20...43
Step
1
Units
dB
Formula for getting
internal value
internal_value = gui_value
Default value
-20
Default value notes
-
Required on creation
optional
Modification
On-Line
Modified
-
Related parameters
ciTargetOscDfr of
BSC - Soft
Blocking C/I OSC DFR parameter value must be
equal to or smaller than C/I Target OSC DFR
Parameter relationships
-
Table 468
DN9813866
Base Station Controller (BSC) radio network object parameters
Soft Blocking C/I OSC DFR
Id:0900d8058089b05f
Confidential
641
Base Station Controller (BSC) radio network object parameters
Related options
•
OSC Full Rate with SAIC MS (160) (optional)
AND DFCA (Dynamic Frequency And Channel
Allocation) Usage (70) (optional) AND AMR
FR (50) (optional)
Feature dependencies
•
BSS21309 OSC Half Rate With SAIC MS
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
-
File based provisioning
supported
true
MML Abbreviated Name
SBDFR
MML Commands
EEH, EEO
MML Full Name
soft blocking C/I OSC DFR
Segment Level Parameter
-
Table 468
9.276
Soft Blocking C/I OSC DFR (Cont.)
soft blocking C/I OSC DHR (SBDHR)
Parameter name
Soft Blocking C/I OSC DHR
Abbreviated name
softBlockingCiOscDhr
3GPP name
-
Managed Object
BSC
Multiplicity
1
Description
With this parameter you define the minimum
acceptable C/I value for double half rate connections.
Additional information
-
Range
-20...43
Step
1
Units
dB
Formula for getting
internal value
internal_value = gui_value
Default value
-20
Default value notes
-
Required on creation
optional
Modification
On-Line
Table 469
642
BSS Radio Network Parameter Dictionary
Soft Blocking C/I OSC DHR
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Modified
-
Related parameters
ciTargetOscDhr of BSC - Soft Blocking C/I OSC
DHR parameter value must be equal to or smaller
than C/I Target OSC DHR.
Parameter relationships
-
Related options
•
Double Half Rate with SAIC MS (146)
(optional) AND DFCA (Dynamic Frequency
And Channel Allocation) Usage (70) (optional)
AND AMR HR (72) (optional)
Feature dependencies
•
BSS21391 DFCA support for OSC
Interfaces
•
•
RACApp <-> RAC
RAC <-> BSC
References
NSN reference: Orthogonal Sub Channel
BSS21309, BSS30385, BSS30390 IS.NSN reference: DFCA support for OSC BSS21391
File based provisioning
supported
true
MML Abbreviated Name
SBDHR
MML Commands
EEH, EEO
MML Full Name
soft blocking C/I OSC DHR
Segment Level Parameter
-
Table 469
9.277
Base Station Controller (BSC) radio network object parameters
Soft Blocking C/I OSC DHR (Cont.)
soft blocking C/I SDCCH (SBSD)
Parameter name
DFCA Soft Blocking C/I SDCCH
Abbreviated name
dfcaSoftBlockingCiSDCCH
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the soft blocking C/I value
for SDCCH connection on DFCA layer.
Note: DFCA Target C/I SDCCH is also related to this
parameter, DFCA Soft Blocking C/I SDCCH value should
be defined equal or smaller than value for C/I target
SDCCH.
Additional information
-
Range
-20...43
Step
1
Unit
dB
Table 470
DN9813866
DFCA Soft Blocking C/I SDCCH
Id:0900d8058089b05f
Confidential
643
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Formula for getting internal
value
internal_value = gui_value
Default value
-20 dB
Default value notes
C/I blocking is disabled by default
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
DFCA Soft Blocking C/I SDCCH value should be defined
equal or smaller than value for DFCA C/I Target SDCCH.
Related parameters
dfcaCiTargetSDCCH of BSC - DFCA C/I Target SDCCH
is used for setting target C/I value for SDCCH connection
Parameter relationships
-
Related options
•
DFCA (Dynamic Frequency And Channel Allocation)
Usage (70) (optional) AND SDCCH and PS Data
Channels on DFCA TRX (136) (optional)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
BSS21161: SDCCH and PS Data Channels on
DFCA TRX
•
•
•
Interfaces
RACApp <-> RAC
RAC <-> BSC
References
-
MML Commands
EEH, EEO
MML Abbreviated Name
SBSD
MML Full Name
soft blocking C/I SDCCH
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 470
9.278
soft blocking C/N 14.4 (SBCN)
Parameter name
Soft Blocking C/N 14.4
Abbreviated name
dfca144Connection_softBlockingCn
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the minimum
acceptable carrier/noise ratio for circuit switched
data connections of 14.4 kbit/s.
Additional information
-
Table 471
644
DFCA Soft Blocking C/I SDCCH (Cont.)
Soft Blocking C/N 14.4
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Range
0...63
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
14 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
High Speed Circuit Switched Data (HSCSD TCSM2) (25) (optional) OR Data 144 Usage
(69) (optional)
Feature dependencies
•
BSS11052: Dynamic Frequency and Channel
Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
SBCN
MML Full Name
soft blocking C/N 14.4
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 471
9.279
Soft Blocking C/N 14.4 (Cont.)
soft blocking C/N AMR FR (SBCNAF)
Parameter name
Soft Blocking C/N AMR FR
Abbreviated name
dfcaAmrFrConnection_softBlockingCn
Managed object
BSC
Multiplicity
1
Table 472
DN9813866
Base Station Controller (BSC) radio network object parameters
Soft Blocking C/N AMR FR
Id:0900d8058089b05f
Confidential
645
Base Station Controller (BSC) radio network object parameters
BSS Radio Network Parameter Dictionary
Description
With this parameter you define the minimum acceptable
carrier/noise ratio for full rate AMR and full rate AMR-WB
speech connections.
Additional information
-
Range
0...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
7 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
AMR FR (50) (optional) OR Wideband AMR (133)
(optional)
Related features
•
•
•
BSS20960: Wideband AMR
BSS20249: AMR FR Licence Control
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
SBCNAF
MML Full Name
soft blocking C/N AMR FR
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 472
9.280
soft blocking C/N AMR HR (SBCNAH)
Parameter name
Soft Blocking C/N AMR HR
Abbreviated name
dfcaAmrHrConnection_softBlockingCn
Managed object
BSC
Table 473
646
Soft Blocking C/N AMR FR (Cont.)
Soft Blocking C/N AMR HR
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Multiplicity
1
Description
With this parameter you define the minimum acceptable
carrier/noise ratio for half rate AMR speech connections.
Additional information
-
Range
0...63
Step
1
Unit
dB
Formula for getting internal
value
internal_value = gui_value
Default value
12 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
•
AMR HR (72)
Related features
•
BSS11052: Dynamic Frequency and Channel Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
SBCNAH
MML Full Name
soft blocking C/N AMR HR
Segment Level Parameter
-
File Based Provisioning sup- true
ported
Table 473
9.281
soft blocking C/N FR (SBCNF)
Parameter name
Soft Blocking C/N FR
Abbreviated name
dfcaFrConnection_softBlockingCn
Managed object
BSC
Multiplicity
1
Table 474
DN9813866
Soft Blocking C/N AMR HR (Cont.)
Soft Blocking C/N FR
Id:0900d8058089b05f
Confidential
647
Base Station Controller (BSC) radio network object parameters
Description
With this parameter you define the minimum
acceptable carrier/noise ratio for full rate and EFR
speech connections, and for circuit switched data
connections up to 9.6 kbit/s.
Additional information
-
Range
0...63
Step
1
Unit
dB
Formula for getting
internal value
internal_value = gui_value
Default value
12 dB
Default value notes
-
Required on Creation
optional
Related functions
-
Modification
On-Line
Modified
-
Related parameters
-
Parameter relationships
-
Related options
-
Feature dependencies
•
BSS11052: Dynamic Frequency and Channel
Allocation
Interfaces
•
•
RAC <-> RACApp
RAC <-> BSC
References
-
MML Commands
EEQ, EEO
MML Abbreviated Name
SBCNF
MML Full Name
soft blocking C/N FR
Segment Level Parameter
-
File Based Provisioning
supported
true
Table 474
9.282
Soft Blocking C/N FR (Cont.)
Soft Blocking C/N HR (SBCNH)
Parameter name
Soft Blocking C/N HR
Abbreviated name
dfcaHrConnection_softBlockingCn
Table 475
648
BSS Radio Network Parameter Dictionary
Soft Blocking C/N HR
Id:0900d8058089b05f
Confidential
DN9813866
BSS Radio Network Parameter Dictionary
Base Station Controller (BSC) radio network object parameters
Managed object
BSC
Multiplicity
1
Description
With this parameter you define the minimum acceptable
carrier/noise ratio for half rate speech connections.
Additional information
-
Range
0...63