8 7 6 4 5 2 3 1 6" MANUAL ISOLATION VALVE 6" PLUG VALVE FOR PRESSURE CONTROL F F 6" FLOW METER E 2" FLUSH PORT E 6" PIPE 8" PIPE 8" PIPE D D FLOW IN FROM SLURRY PUMP #2 ARISDYNE SYSTEMS INC. CAVITATION SYSTEM (2X) 2" FLUSH PORT C - REV C D 8" PIPE B B 8" DIVERTER VALVE MANIFOLD = PROCESS FLOW PRE CAVITATION 8" PIPE = PROCESS FLOW POST CAVITATION A FLOW OUT TO HYDRO HEATER PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ARISDYNE SYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ARISDYNE SYSTEMS, INC. IS PROHIBITED. 8 7 NAME UNLESS OTHERWISE SPECIFIED: 6 5 4 3 NEXT ASSY USED ON APPLICATION 2 DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 0.5 BEND: 0.5 CHAMFER ANGLE: 2 TWO PLACE DECIMAL: .004 THREE PLACE DECIMAL: .002 BREAK EDGES: .005 - .010 DRAWN BY: INTERPRET GEOMETRIC TOLERANCING PER: ANSI Y14.5M-1994 CLIENT: MATERIAL COMMENTS: FINISH DO NOT SCALE DRAWING DATE A CHECKED ENG APPR. DESCRIPTION: 100MMGPY Plant layout MFG APPR. SIZE PART NO. D SCALE: 1:64WEIGHT: 1 REV SHEET 1 OF 3 7 8 6 4 5 2 3 1 F DIM. F DIM. 62" MIN. 72" MAX. .630 .630 120" MIN. E E CL I-BEAM W/PULLEY [STRAINER BASKET REMOVAL] D ELEV. FOR SLURRY TANK #2 INLET BASE ON CATWALK LOCATION [CUSTOMER REQUEST] D X = 30" MIN. STRAIGHT X CL ELEV. X C C - 9" EST. REV CL BASED ON EXISTING PIPE RUN CL ELEV. B D CL ELEV. B A 36" MIN. WALK THROUGH CLEARANCE 36" STRAIGHT MIN. PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ARISDYNE SYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ARISDYNE SYSTEMS, INC. IS PROHIBITED. 8 7 6 NAME UNLESS OTHERWISE SPECIFIED: 5 4 3 NEXT ASSY USED ON APPLICATION 2 DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 0.5 BEND: 0.5 CHAMFER ANGLE: 2 TWO PLACE DECIMAL: .004 THREE PLACE DECIMAL: .002 BREAK EDGES: .005 - .010 DRAWN BY: INTERPRET GEOMETRIC TOLERANCING PER: ANSI Y14.5M-1994 CLIENT: MATERIAL COMMENTS: FINISH DO NOT SCALE DRAWING DATE A CHECKED ENG APPR. DESCRIPTION: 100MMGPY Plant layout MFG APPR. SIZE PART NO. D SCALE: 1:64WEIGHT: 1 REV SHEET 2 OF 3 8 7 6 4 5 2 3 1 F F E E D D C D - REV C B B NAME UNLESS OTHERWISE SPECIFIED: A PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ARISDYNE SYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ARISDYNE SYSTEMS, INC. IS PROHIBITED. 8 7 6 5 4 3 NEXT ASSY USED ON APPLICATION 2 DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 0.5 BEND: 0.5 CHAMFER ANGLE: 2 TWO PLACE DECIMAL: .004 THREE PLACE DECIMAL: .002 BREAK EDGES: .005 - .010 DRAWN BY: INTERPRET GEOMETRIC TOLERANCING PER: ANSI Y14.5M-1994 CLIENT: MATERIAL COMMENTS: FINISH DO NOT SCALE DRAWING DATE A CHECKED ENG APPR. DESCRIPTION: 100MMGPY Plant layout MFG APPR. SIZE PART NO. D SCALE: 1:64WEIGHT: 1 REV SHEET 3 OF 3 7 8 6 4 5 46.875 F E 20.6 13.750 13.750 20.6 2 3 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 ASI# - 11887 ASSEMBLY, VALVE, BUTTERFLY, ISLIP 8IN, LUG STYLE, PTFE SEAT, FAIL OPEN 1 2 ASI# - 11769 ASSEMBLY, FITTING, PIPE, SCH1O, 8IN EQUAL TEE, LAP JOINT, AISI 304 2 3 ASI# - 11825 GASKET, EtOH, ANSI 150#, FULL FACE, 8IN X .125, GARLOCK 5500 4 4 ASI# - 11888 ASSEMBLY, VALVE, BUTTERFLY, ISLIP 8IN, LUG STYLE, PTFE SEAT, FAIL CLOSED 2 5 ASI# - 11918 FITTING, MANIFOLD, 3x .375 NPT INLET X .250 NPT OUTLET, BRASS 1 6 ASI# - 11922 FITTING, PIPE, HEX NIPPLE, 3/8NPT X 1-29/64IN 1 7 ASI# - 11914 Pneumatic, Air Filter & Regulator, 3/8 NPT, 5-150 PSI, 60 SCFM @ 150 PSI 1 8 ASI# - 11921 FITTING, MUFFLER, 1/4 NPT, 70 SCFM, AISI 304 3 9 ASI# - 11916 FITTING, PUSH-TO-CONNECT, .375 TUBE X .250 NPT MALE, POLY & BRASS 3 10 ASI# - 11917 FITTING, PUSH-TO-CONNECT, SWVL ELBOW, .375 TUBE X .375 NPT MALE, NYLON & NICKEL 3 11 ASI# - 11919 FITTING, NIPPLE, 3/8 NPT HEX PLUG, 150PSI, AISI 304 1 12 ASI# - 11605 WASHER, FLAT, 3/4IN, GRADE 8, ZINC & YELLOW 32 13 ASI# - 11606 WASHER, SPRING LOCK, 3/4IN, HVY DUTY, ZINC & YELLOW 32 14 ASI# - 11855 SCREW, HHC, 3/4-10 x 3.00 UNC-2A, GRADE 5, ZINC PLATED 32 F E D D 11 9 6 5 8 C C 29 29 11920 - REV 10 4 D 7 B B NAME UNLESS OTHERWISE SPECIFIED: A 2 8 13 7 12 1 14 6 PROPRIETARY AND CONFIDENTIAL 3 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ARISDYNE SYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ARISDYNE SYSTEMS, INC. IS PROHIBITED. 5 4 3 NEXT ASSY USED ON APPLICATION 2 DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 0.5 BEND: 0.5 CHAMFER ANGLE: 2 TWO PLACE DECIMAL: .004 THREE PLACE DECIMAL: .002 BREAK EDGES: .005 - .010 DRAWN BY: INTERPRET GEOMETRIC TOLERANCING PER: ANSI Y14.5M-1994 CLIENT: MATERIAL COMMENTS: FINISH DO NOT SCALE DRAWING PBL DATE A 02/05/10 CHECKED ENG APPR. MFG APPR. DESCRIPTION: DIVERTER VALVE ASSEMBLY - ANSI 150#, 8IN x 8IN, PNEUMATIC ACTUATORS SIZE PART NO. D 11920 SCALE: 1:8 WEIGHT: 1 REV SHEET 1 OF 2 8 7 6 4 5 2 3 1 F F E E D 11.000 TYP D C C D 11769 - REV 11.000 B B 8" lap Joint Flanges 150# 304 Stainless Steel A 22.000 PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ARISDYNE SYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ARISDYNE SYSTEMS, INC. IS PROHIBITED. 8 7 6 5 4 NAME UNLESS OTHERWISE SPECIFIED: 3 DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 0.5 BEND: 0.5 CHAMFER ANGLE: 2 TWO PLACE DECIMAL: .004 THREE PLACE DECIMAL: .002 BREAK EDGES: .005 - .010 DRAWN BY: INTERPRET GEOMETRIC TOLERANCING PER: ANSI Y14.5M-1994 CLIENT: MATERIAL COMMENTS: AISI 304 NEXT ASSY USED ON APPLICATION 2 FINISH DO NOT SCALE DRAWING DATE A CHECKED ENG APPR. MFG APPR. DESCRIPTION: ASSEMBLY, FITTING, PIPE, SCH1O, 8IN EQUAL TEE, LAP JOINT, AISI 304 SIZE PART NO. D 11769 SCALE: 1:8 WEIGHT: 1 REV SHEET 2 OF 2 8 7 5 6 4 2 3 1 D D C C 46.875 8" MSSTYPE-A STUB END AISI 304 2 PLACES B B 8" 150# LAP JOINT ANSI FLANGE AISI 304 2 PLACES 8" SCH 10 PIPE AISI 304 NAME UNLESS OTHERWISE SPECIFIED: A PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ARISDYNE SYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ARISDYNE SYSTEMS, INC. IS PROHIBITED. 8 7 6 5 DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 0.5 BEND: 0.5 CHAMFER ANGLE: 2 TWO PLACE DECIMAL: .004 THREE PLACE DECIMAL: .002 BREAK EDGES: .005 - .010 DRAWN BY: INTERPRET GEOMETRIC TOLERANCING PER: ANSI Y14.5M-1994 Q.A. MATERIAL RHG DATE 4/29/2010 CHECKED DESCRIPTION: ENG APPR. FITTING, PIPE, SCH10, 8IN SPOOL, DIVERTER VALVE REPLACEMENT, AISI 304 MFG APPR. COMMENTS: SIZE PART NO. B AISI 304 NEXT ASSY USED ON APPLICATION 4 FINISH STOCK - 12039 SHEET 1 OF 1 SCALE: 1:8 WEIGHT: DO NOT SCALE DRAWING 3 REV 2 1 A 8 5 6 7 4 2 3 1 ASI -11780 -1TC ASI -11780 -2TC ASI -11780 -3TC ASI -11780 -1MFS 2" D D xxx-6" xxx 6" TT 01 PI 01 TT 02 PI 02 TT 03 6" PI 03 FV 04 FT 01 CAVITATION UNIT Design: Specific Mech: Static Style: O/P PT 01 xxx-8" C CP-xxxx Service: Cavitation Pump Capacity: 1500GPM @ xTDH Discharge: 8x4-25 RPM: 1800 HP: 500 6" MAG PC 01 C PT 03 PT 02 ASI -11780 -1PPV ASI -11780 -3PT ASI -11780 -1PT ASI -11780 -2PT 2" 2" ASI-11780-1SOL ASI-11780-2SOL 8" B 8" ASI-11780-3SOL FV 01 B FV 02 xxx-8" xxx 8" xxx FV 03 CP-xxxx Service: Slurry Pump Capacity: xGPM @ xTDH Discharge: xxx RPM: xxx HP: x A PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ARISDYNE SYSTEMS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ARISDYNE SYSTEMS, INC. IS PROHIBITED. 8 7 NAME UNLESS OTHERWISE SPECIFIED: 6 5 DIMENSIONS ARE IN INCHES TOLERANCES: ANGULAR: 0.5 BEND: 0.5 CHAMFER ANGLE: 2 TWO PLACE DECIMAL: .004 THREE PLACE DECIMAL: .002 BREAK EDGES: .005 - .010 DRAWN BY: INTERPRET GEOMETRIC TOLERANCING PER: ANSI Y14.5M-1994 Q.A. MATERIAL NEXT ASSY USED ON APPLICATION 4 DATE CHECKED DESCRIPTION: ENG APPR. A MFG APPR. COMMENTS: SIZE PART NO. REV B FINISH SHEET 1 OF 1 SCALE: 1:8 WEIGHT: DO NOT SCALE DRAWING 3 - 2 1
