PV Elite® Product: PV Elite (PVE) Version: 24 (24.00.00) Date: Description: Sections: December 2021 PV Elite analyzes and designs pressure vessels and heat exchangers in accordance with U.S. National and International codes and standards, such as ASME, PD 5500, and EN 13445. System Requirements Version Compatibility Special Instructions Documentation Training Customer Support Fixes Open Problems Legal Notices System Requirements Beginning with Windows 10, Microsoft enforces the Internet Host Table Specification RFC 952 which mandates that component hostname labels can contain only alphanumeric characters. Hostnames using underscores (‘_’) are not allowed. Refer to Microsoft KB 101785.Intergraph PV Elite is compatible with Windows desktop operating systems listed below Intergraph PV Elite is compatible with Windows desktop operating systems listed below. The operating system compatibility details that follow refer to the latest released version of this software. Previous versions of the software might not work with newer operating systems. Version Compatibility For up-to-date information on the software compatibility of this product in a standalone or integrated environment, please refer to the Compatibility Matrix on the Hexagon PPM Support Web site at https://smartsupport.intergraph.com/. Log on and perform the following steps: 1. Click the View Downloads tab. 2. 3. Click the Product Compatibility link under Useful Links on the right side. On the PPM Compatibility Matrix - Product Report page, from the Select Product list, select PV 4. Elite. From the Version list, select the version of PV Elite. Special Instructions PV Elite Version 24 runs on Windows 10. PV Elite may work on Windows 11 and earlier versions of Windows (Vista/7/8/8.1), although these platforms have not been tested. Documentation General Use the Help menu to access the Help files and Printable Guides for this product. For the latest support information for this product, connect to https://hexagonppm.com/ppm-support. Also, you can submit any documentation comments or suggestions you might have on the Hexagon PPM support site. Printed documentation is not available for separate purchase. PDF Files The documentation is provided as .pdf files. You can use any PDF viewer to view the files. Training To register for training on Hexagon PPM products, call Training Registration at (800) 766-7701 in the U.S. Outside the U.S., call (256) 730-5400 or contact your local Hexagon PPM office. For current information on training, connect to https://hexagonppm.com/offerings/training/instructor-led-training#products=PV%20Elite . Customer Support For the latest Support Services information for this product, including solutions to known software issues, connect to https://smartcommunity.hexagonppm.com. To open service requests outside the U.S., please contact your local Hexagon PPM office. New Features Code Updates Updated the following codes: ▪ EN 13445-3:2021. (CR-TX-38769) ▪ EN 13445-3, Section 16.12 Vertical vessels with skirts. (RI-TX-35673) ▪ EN 13445-3, Bearing plate. (RI-TX-36948) ▪ EN13445-3, Section 21, Circular flat ends with radial reinforcement ribs. (RI-TX-37181) ▪ EN 1991-1-4, Vortex shedding. (CR-TX-37441) ▪ ASME Section VIII 2021. (RI-TX-37178) ▪ UHX-13.10.2(c). Added a warning if the cone angle is greater than 60 degrees. (CR-TX-37805) ▪ UW-20 and Appendix A. Addressed new MDMT calculations, maximum cone angle calculations, and new inset tube welding calculations. (CR-TX-37848) Input Processor and Analysis ▪ Added EN 13445-3, Section 16.12 support for vertical vessels with skirts. See Bolt Friction Factor mu | Assembly Factor phi and Basering Design Option. (RI-TX-35673) ▪ Added the option to use up to three times the allowable stress for pressure-only tubesheet load cases for EN-13445. See Load Cases Tab (Heat Exchanger Tubesheet Input Dialog Box). (CRTX-38326, CR-TX-37934) ▪ Added the option to perform MDMT heat exchanger calculations on the selected load case. See Load Cases Tab (Heat Exchanger Tubesheet Input Dialog Box). (CR-TX-39057) ▪ Added the Rib/Stiffener Analysis command, which creates and analyzes radial stiffeners on a welded flat head. (RI-TX-37181) ▪ Added support for the 2015 code year of the Mexico Sismo seismic code (CFE-MDOC). See Damping Factor (B) (optional) and Overresistance Factor (R) (optional). (CR-TX-39281) ▪ Added support for blast load analysis to the Special Effective Wind Diameter & Blast Load Input Dialog on the Wind Data Tab. (CR-TX-38879) ▪ Added color-coded channel-side and shell-side element grid descriptions to Element Data (General Input Tab). The color depends on the selected element in heat exchanger models. (CR-TX-39208) ▪ Added 1.5 as an option for Nominal Size Lookup. (CR-TX-37293) ▪ Added an option to exclude the BOM report from the output by adding the text "#NO_BOM" in the Title Page Text dialog. (CR-TX-38357) ▪ Added the option of forcing the Arl and Ars for cones attached to cylinders. Calculations are only required according to 1-5(g) for Conical sections. (CR-TX-38546) ▪ You can now view the unit constants and labels that were stored in the input file and create a new unit file (*.FIL) using that information if the unit file is missing from the CAESAR II System folder. (CR-TX-38947) ▪ The software now performs a check when Appendix 26 is selected, and the type is Thick Exp. Joint. Appendix 26 data is then removed, and Appendix 26 is cleared. (TR-TX-37790) Output Processor and Reports ▪ The software displays a message and calculations when the MAWPs are negative for UG-44(b) calculations. (CR-TX-37792) ▪ Changed the pressure testing data fields on the Design Constraints tab to label Shop or Field pressure test types. (CR-TX-36769) ▪ For the PD5500 code and when the design temperature for external pressure is greater than the design temperature for internal pressure, the software now shows the warning in orange in the warning and errors section of the output report. (CR-TX-37884) ▪ The software checks if the result for Volume of Exchanger tubes is less than one in the Element and Detail Weight report. If so, the result displays to 5 decimal places so that it is understandable. (CR-TX-37897) ▪ Added a UG-41 and UW-15 note for clarification of allowable stresses in the nozzle output report when calculating the strength of connection elements with the failure path analysis. (CR-TX37516) ▪ Added a note when the maximum shell thickness exceeds 3/8 in. (10 mm) according to Appendix 14-1, Figure UW-13.2, Sketches (c) and (d). (CR-TX-38358) ▪ Added a warning note when the jacket internal design temperature is greater than the external temperature of the core and jacket. (CR-TX-38596) ▪ The software now considers the area of the partition gasket in the PCC-1 Appendix O calculations report. (CR-TX-38345) ▪ Added a warning when the expansion joint ID and OD are zero or smaller than the shell OD. (CR-TX-38441) ▪ When the half apex angle is less than 30 degrees, the software indicates that the discontinuity stress computation results are for information only. (CR-TX-38438) ▪ When a nozzle is hub type Self-Reinforcing and the FVC catalogue is used, the Nozzle Schedule report displays the FVC type in Nozzle Schedule table. (CR-TX-38937) ▪ Added a cone to the cylinder junction weld NDE warning. (CR-TX-39243) ▪ Removed the mean metal temperature input echo printout in the output report when the value is disabled in input. (CR-TX-39243) Documentation/Help ▪ Added a help topic for an MAWP for pressure testing option on the Tubesheet Type and Design Code Tab (Heat Exchanger Tubesheet Input Dialog Box). (CR-TX-36805) ▪ Clarified the description of Weight to Use for Lifting Analysis on the Equipment Installation and Miscellaneous Options Dialog Box. (CR-TX-37111) ▪ Updated help for the Stiffening Ring command to include all fields for the EN-13445 Ring dialog box. (DI-TX-38361) ▪ Updated Tube Joint Type to the ASME 2021 edition. (CR-TX-38741) ▪ Added a note to clarify how jacket calculations use the nozzle Projection Inside. (CR-TX-36204) ▪ Added an explanation for the Weldability Limit Thickness default value used for Retirement Limit Calculations. (CR-TX-39437) ▪ Updated the installation and silent installation instructions. Fixes User Interface/Graphics • • • • The software no longer displays The flange is considered for moment of inertia calculations note when the flange is within the limit of 16*tn (22in) according to Figure 1-7-2. (TR-TX37543) The software no longer sets Attached Shell Thickness to the flange thickness when no cylinder is attached to it for an integral ring flange. (CR-TX-38998) You can now define a shock scale factor of zero in the Y-direction for the Response Spectrum seismic design code. (TR-TX-38537) For conical heads, Offset Dimension is now active for angled or lateral nozzles. When you define an offset dimension, the software automatically calculates the Distance From value. (CR-TX-39388) Output Reports • • • • • • • • • • • • The spring rate stiffness value now uses a conversion constant when using metric units for the ASME TS Calc report. (TR-TX-37730) Adjusted the value of Pj in the calculation of Req'd Half-Pipe Jacket Thickness to only consider the jacket pressure. (TR-TX-37878) Bellows calculations in CodeCalc now use the correct equation for the circumferential membrane stress in the collar for un-reinforced bellows, according to Appendix 26-6.3.2. (TRTX-38011) For very low shear stress load cases, the software sets the required tubesheet thickness to the tube diameter and includes a warning. (TR-TX-37979) Fixed and modified the equation substitution for Longitudinal Wind Force [Fl] to fit the correct results in the Saddle Calcs: Operating Case report. (TR-TX-38203) Removed a conservative extra weight added to each saddle to account for the difference between the new metal weight and the corroded metal weight. (TR-TX-37681) If the double rings pitch is less than the calculated h value according to Fig. 4.15.3(c), the software treats the double rings as a single ring and use formulas (4.15.32) through (4.15.34) in the Saddle Calculation report according to ASME Interpretation BPV VIII-2-20-04. (TR-TX38450) Removed a nozzle layout warning when the nozzle is modeled on a cone and has no obstruction in the Nozzle Calculation report. (TR-TX-38354) Corrected the final MAPnc value of the shells and flanges in the Internal Pressure Calculations and Nozzle Summary reports. (TR-TX-38693) Changed when messages display on iterative calculations. Fixed a case with an overstress in the first pass, but not in subsequent runs. The nozzle is not overstressed because the software reduces the MAPnc value based on nozzle reinforcement, and no message displays. (TR-TX-38527) Nozzle torsional moment equations now match the results for the DeltaMz value in nozzle EN 13445 calculations. (TR-TX-38615) Both Long Joint & Circumferential Joint descriptions display independently from selection of Weld is Pre-Heated. (TR-TX-38995) • • • • • • • • When calculating Vh(ope), the software bases the value of Davg on the insulated OD of the vessel. This applies to Vortex Shedding Loads in the Wind Calculation report according to the NBC 1990 Supplement section. (TR-TX-38759) Added the following note when the EQ load factor is negative: Neutral axis shift calculations are not performed due to a low bending moment. (TR-TX-38433) When you select a blind flange type in the Flange dialog, the input echo displays the correct ID/OD reference. (TR-TX-39034) When more than two saddles are attached, the software now calculates the Saddle Load as the total vessel weight minus total weight of the saddles divided by the number of saddles. (TR-TX-39144) Fixed a formula substitution for the force acting on the Shell fs nozzle calculation to eliminate a Divided by Zero warning. (TR-TX-39261) The BOM Report now displays the same baffle thickness as the baffle input when in metric units. (TR-TX-39237) Dimension h now uses the vertical distance from the base of the leg to the center of the support bracket. (CR-TX-39260) Added the following note in the XY Coordinate Calculations report: PV Elite includes a 1/8 inch (3.175mm) raised face and gasket thicknesses for girth flanges and tubesheet thicknesses where applicable in the tangent-to-tangent length calculation. The calculated dimensions are based on the given element lengths. Due to variability in manufacturing (weld gaps etc.), the tangent-to-tangent length may not be exact. (CR-TX-39335) Open Problems None Legal Notices Copyright Copyright © 1993-2021 Hexagon AB and/or its subsidiaries and affiliates. All rights reserved. Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret law, and international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph Corporation. Contains RealDWG™ by Autodesk, Inc. Copyright © 1998-2021 Autodesk, Inc. All rights reserved. U.S. Government Restricted Rights Legend Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was developed at private expense and is "restricted computer software" submitted with restricted rights in accordance with subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal Acquisition Regulations ("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of the United States. For units of the Department of Defense ("DoD"): This is "commercial computer software" as defined at DFARS 252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3. Unpublished - rights reserved under the copyright laws of the United States. Hexagon PPM 305 Intergraph Way Madison, AL 35758 Documentation Documentation shall mean, whether in electronic or printed form, User's Guides, Installation Guides, Reference Guides, Administrator's Guides, Customization Guides, Programmer's Guides, Configuration Guides and Help Guides delivered with a particular software product. Other Documentation Other Documentation shall mean, whether in electronic or printed form and delivered with software or on Intergraph Smart Support, SharePoint, box.net, or the Hexagon PPM documentation web site, any documentation related to work processes, workflows, and best practices that is provided by Intergraph as guidance for using a software product. Terms of Use Use of a software product and Documentation is subject to the Software License Agreement ("SLA") delivered with the software product unless the Licensee has a valid signed license for this software product with Intergraph Corporation. If the Licensee has a valid signed license for this software product with Intergraph Corporation, the valid signed license shall take precedence and govern the use of this software product and Documentation. Subject to the terms contained within the applicable license agreement, Intergraph Corporation gives Licensee permission to print a reasonable number of copies of the Documentation as defined in the applicable license agreement and delivered with the software product for Licensee's internal, non-commercial use. The Documentation may not be printed for resale or redistribution. For use of Documentation or Other Documentation where end user does not receive a SLA or does not have a valid license agreement with Intergraph, Intergraph grants the Licensee a nonexclusive license to use the Documentation or Other Documentation for Licensee’s internal noncommercial use. Intergraph Corporation gives Licensee permission to print a reasonable number of copies of Other Documentation for Licensee’s internal, non-commercial use. The Other Documentation may not be printed for resale or redistribution. This license contained in this subsection b) may be terminated at any time and for any reason by Intergraph Corporation by giving written notice to Licensee. Disclaimer of Warranties Except for any express warranties as may be stated in the SLA or separate license or separate terms and conditions, Intergraph Corporation disclaims any and all express or implied warranties including, but not limited to the implied warranties of merchantability and fitness for a particular purpose and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such disclaimer. Intergraph believes the information in this publication is accurate as of its publication date. The information and the software discussed in this document are subject to change without notice and are subject to applicable technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document. The software, Documentation and Other Documentation discussed in this document are furnished under a license and may be used or copied only in accordance with the terms of this license. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT. Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data. Users should verify for themselves that the data is accurate and suitable for their project work. Limitation of Damages IN NO EVENT WILL INTERGRAPH CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL INCIDENTAL, SPECIAL, OR PUNITIVE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR PRODUCTION, LOSS OF REVENUE OR PROFIT, LOSS OF DATA, OR CLAIMS OF THIRD PARTIES, EVEN IF INTERGRAPH CORPORATION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. UNDER NO CIRCUMSTANCES SHALL INTERGRAPH CORPORATION’S LIABILITY EXCEED THE AMOUNT THAT INTERGRAPH CORPORATION HAS BEEN PAID BY LICENSEE UNDER THIS AGREEMENT AT THE TIME THE CLAIM IS MADE. EXCEPT WHERE PROHIBITED BY APPLICABLE LAW, NO CLAIM, REGARDLESS OF FORM, ARISING OUT OF OR IN CONNECTION WITH THE SUBJECT MATTER OF THIS DOCUMENT MAY BE BROUGHT BY LICENSEE MORE THAN TWO (2) YEARS AFTER THE EVENT GIVING RISE TO THE CAUSE OF ACTION HAS OCCURRED. IF UNDER THE LAW RULED APPLICABLE ANY PART OF THIS SECTION IS INVALID, THEN INTERGRAPH LIMITS ITS LIABILITY TO THE MAXIMUM EXTENT ALLOWED BY SAID LAW. Export Controls Intergraph Corporation’s commercial-off-the-shelf software products, customized software and/or third-party software, including any technical data related thereto (“Technical Data”), obtained from Intergraph Corporation, its subsidiaries or distributors, is subject to the export control laws and regulations of the United States of America. Diversion contrary to U.S. law is prohibited. To the extent prohibited by United States or other applicable laws, Intergraph Corporation software products, customized software, Technical Data, and/or third-party software, or any derivatives thereof, obtained from Intergraph Corporation, its subsidiaries or distributors must not be exported or re-exported, directly or indirectly (including via remote access) under the following circumstances: To Cuba, Iran, North Korea, the Crimean region of Ukraine, or Syria, or any national of these countries or territories. To any person or entity listed on any United States government denial list, including, but not limited to, the United States Department of Commerce Denied Persons, Entities, and Unverified Lists, the United States Department of Treasury Specially Designated Nationals List, and the United States Department of State Debarred List (https://build.export.gov/main/ecr/eg_main_023148). To any entity when Customer knows, or has reason to know, the end use of the software product, customized software, Technical Data and/or third-party software obtained from Intergraph Corporation, its subsidiaries or distributors is related to the design, development, production, or use of missiles, chemical, biological, or nuclear weapons, or other unsafeguarded or sensitive nuclear uses. To any entity when Customer knows, or has reason to know, that an illegal reshipment will take place. Any questions regarding export/re-export of relevant Intergraph Corporation software product, customized software, Technical Data and/or third-party software obtained from Intergraph Corporation, its subsidiaries or distributors, should be addressed to PPM’s Export Compliance Department, 305 Intergraph Way, Madison, Alabama 35758 USA or at exportcompliance@intergraph.com. Customer shall hold harmless and indemnify PPM and Hexagon Group Company for any causes of action, claims, costs, expenses and/or damages resulting to PPM or Hexagon Group Company from a breach by Customer. Trademarks Intergraph, the Intergraph logo, Intergraph Smart, PDS, SmartPlant, SmartMarine, FrameWorks, I-Sketch, IntelliShip, Isogen, SmartSketch, SPOOLGEN, SupportManager, and SupportModeler are trademarks or registered trademarks of Intergraph Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation. MicroStation is a registered trademark of Bentley Systems, Inc. Other brands and product names are trademarks of their respective owners.