L
JumpStart Guide
Trimble® QuickPen
PipeDesigner 3D®
Software
Revision A
February 2013
F
Englewood Office
Trimble Navigation Limited
384 Inverness Parkway, Suite 200
Englewood, Colorado 80112
(800) 234-3758
Copyright and Trademarks
©1998 - 2013 Trimble Navigation Limited.
All rights reserved.
QuickPen is a trademark of Trimble Navigation Limited
registered in the United States and/or in other countries.
PipeDesigner 3D® and Trimble® Quick Link are
trademarks or registered trademarks of Trimble
Navigation Limited. All other trademarks are the
property of their respective owners.
This publication, or parts thereof, may not be
reproduced in any form, by any method, for any
purpose, without the written consent of Trimble
Navigation Limited.
Release Notice
This is the Trimble® QuickPen PipeDesigner 3D®software
JUMPSTART GUIDE. (Revision A).
The topics within this manual are subject to change
without written notice. Companies, names, and data
used in any examples are fictitious. Screenshots
included in the help topics may not be exactly as in the
software application.
Part Number PD3D8059.02.0113_JumpStart
Wednesday, February 13, 2013 7:24 am
II
JUMPSTART GUIDE
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Software Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Guide Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2
Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Open PipeDesigner 3D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Main PipeDesigner 3D Window . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3
Create a Drawing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
JumpStart Drawing . . . . . . .
Drawing Operations . . . . . .
Vessel Tasks . . . . . . .
Reduction Tee . . . . . .
Connect to Vessel . . . .
Add Remaining Elbows .
Completed Drawing. . .
4
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 18
. 19
. 25
. 31
. 37
. 43
. 45
Additional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Part Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Bill of Material (BOM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Plot the Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
JUMPSTART GUIDE
i ii
iv
JUMPSTART GUIDE
CHAPTER
1
Introduction
1
In this chapter:

Software Overview

PipeDesigner 3D Modules

Guide Overview
The PipeDesigner 3D software provides a
CAD solution to designers of piping
systems. Created by industry specialists,
it is compatible with various Autodesk
applications to enable you to enable you
to design piping systems with cuttingedge speed, efficiency, and accuracy.
INSTALLATION GUIDE
5
1
Introduction
Software Overview
The benefits of the PipeDesigner 3D software include:
• Choosing parts from a database of PipeDesigner 3D entities
• Configuring the system and assigning parts list and an insulation schedule
• Using intelligent PipeDesigner 3D entities
• Less UCS (User Coordinate System) manipulation
The PipeDesigner 3D software is integrated with several Autodesk applications. Refer
to the PipeDesigner 3D software System Specifications document (posted on our
website) for more details on compatible applications.
The instructions included in this Guide use many of the basic Microsoft Windows®
operating systems and AutoCAD terms and concepts. If you are not familiar with these
systems, Trimble recommends that you attend a class. Check with your local computer
vendor for more information.
B
Tip – Although this Guide provides you with much of the information you need
to begin using the PipeDesigner 3D application, Trimble recommends that you
attend a PipeDesigner 3D software class. Contact your Sales Representative at
(800)234-3758 for information on class availability
PipeDesigner 3D Modules
PipeDesigner 3D includes the following modules:
• Trimble® Quick Link
This application provides licensing for the PipeDesigner 3D software modules. It is
required to use the PipeDesigner 3D software.
• PipeDesigner 3D CAD
This module is where you draw the pipe and equipment.
• PipeDesigner 3D Data Editor
The Data Editor allows you to manipulate your data based on your company
standards.
6
INSTALLATION GUIDE
Introduction
1
• QuickMerge
The QuickMerge utility allows you to merge other database files into the
PipeDesigner 3D database, without disturbing your current data. QuickMerge can
be opened from within the PipeDesigner 3D Data Editor or from the Windows Start
menu.
B
Tip – This Guide does not include information about the Trimble Quick Link
software, the PipeDesigner 3D Data Editor or the QuickMerge utilities. Refer to
the Quick Link/PipeDesigner 3D online help system for more details
Guide Overview
The tutorial included in this Guide allows you to begin using the PipeDesigner 3D
software in the shortest time possible, and are designed to give you confidence in
using the application. You will learn how to do the following:
• Navigate through the PipeDesigner 3D application
• Add piping to equipment
• Plot the drawing
Trimble suggests that you read and perform the exercises in each chapter of this Guide
until you are comfortable with the software and can complete the exercises easily.
INSTALLATION GUIDE
7
1
8
Introduction
INSTALLATION GUIDE
CHAPTER
2
Navigation
2
In this chapter:

Requirements

Open PipeDesigner 3D

Main PipeDesigner 3D Window
Using the information in this chapter,
you will be able to navigate through
PipeDesigner 3D using basic Windows®
operating system commands. If you are
not familiar with Microsoft Windows
operating systems, Trimble recommends
that you take an introductory Windows
course. These are typically offered
through local community colleges on
independent training facilities. Your
hardware vendor may also be able to
offer suggestions for classes offered in
your area.
INSTALLATION GUIDE
9
2
Navigation
Requirements
Autodesk Application
The first step to using the PipeDesigner 3D software is to install a compatible version
of Autodesk software. Refer to the System Specifications document posted on our
website under Products > CAD > PipeDesigner 3D for more information.
Trimble® Quick Link Software
Trimble Quick Link is a communication and licensing application. In order to use the
PipeDesigner 3D software, you must license your software using the Trimble Quick
Link software.
PipeDesigner 3D Software
After you have installed the compatible Autodesk and Quick Link applications, you
must install the PipeDesigner 3D software.
B
Tip – Trimble has included a comprehensive Installation manual that steps you
through the entire process. We recommend that you review and follow the
instructions to ensure proper operation of your system.
After you have completed all required installations, completing the exercises in this
Guide will familiarize you with the application.
Open PipeDesigner 3D
B
Tip – The instructions below assume that this is not the first time you have
opened the PipeDesigner 3D software application. If you have not previously
opened the application, refer to the Preliminary Steps chapter in the Installation
Guide included with the software for detailed instructions. The manual is
provided to you in a hard copy format. You can also obtain it from the Windows
Start menu under QuickPen PipeDesigner 3D [Compatible Autodesk
Application] > Documentation.
You can use any of the following methods to open the application.
10
INSTALLATION GUIDE
Navigation
2
Double-click on the QuickPen PipeDesigner 3D [Compatible Autodesk
Application] icon on your desktop.
OR
Go to the Windows Start menu and navigate to QuickPen PipeDesigner 3D >
QuickPen PipeDesigner 3D [Compatible Autodesk application].
OR
Right-click the icon on the desktop and from the menu, click Open.
The Autodesk application opens. When this application is completely open, you must
login to PipeDesigner 3D and select a project.
PipeDesigner 3D Login
B
Tip – The PipeDesigner 3D software allows for themes (defined in the
PipeDesigner 3D Data Editor. Depending on the theme selected, your login
window may not display as in the graphic above.
1. Enter your Login Name and Password.
2. Click OK.
3. In the Select Project dialog, click on the Default Project and then click Select &
Close.
INSTALLATION GUIDE
11
2
Navigation
Graphics Illustrations
For purposes of illustration, the AutoCAD application is used in all graphics in this
Guide. If you are using another compatible Autodesk application, your windows may
appear differently.
Main PipeDesigner 3D Window
The PipeDesigner 3D software is incorporated directly into a compatible Autodesk
application. When the Autodesk application opens, the PipeDesigner 3D software
opens with additional parts, lists, the AutoCAD Menu Browser and AutoCAD Ribbons.
PD3D™ Dashboard (Parts List)
The System and associated Parts List is located on the left side of the main window. As
System and Parts Lists are changed, the available items are updated to show only
those entities assigned to your selection.
12
INSTALLATION GUIDE
Navigation
2
Ribbons/Menus
Because the PipeDesigner 3D software is added to a compatible Autodesk application,
many of the ribbons/menus are AutoCAD commands. Commands are accessed from
the ribbons. This includes both AutoCAD and PipeDesigner 3D software-specific
ribbons.
Many of the PipeDesigner 3D software commands can also be accessed by clicking the
right-mouse button, which opens a sub-menu.
Examples: Right-Click Menus
Model Space
Paper Space
INSTALLATION GUIDE
13
2
Navigation
PipeDesigner 3D Ribbons
Because the PipeDesigner 3D software is added to a compatible Autodesk application,
many of the menus and ribbons belong to the native application. Specific
PipeDesigner 3D commands are added to Autodesk menus and ribbons.
The AutoCAD Ribbon opens automatically when you start PipeDesigner 3D. To view
the PipeDesigner 3D ribbons, click on one of the following ribbon commands.
PD3D™ Draw Ribbon
Simply click on the command button you want to use to activate the procedure.
14
INSTALLATION GUIDE
Navigation
2
PD3D™ Annotate Ribbon
PD3D™ Tools Ribbon
Note: Due to ribbon size, the graphic
above is split into two. The actual
ribbon is only one single ribbon.
Ribbon Features
• Each tab contains multiple panels.
• Panels include multiple tools.
• You can dock or undock panels.
• Panels can be displayed in full tab view or minimized to tab view only.
Command Line
Many of the Autodesk application commands, as well as PipeDesigner 3D softwarespecific commands, can be used at the command line.
Get Started!
Now that you are familiar with the basic structure of PipeDesigner 3D, you are ready
to begin working in the application. This will introduce you to procedures to help you
provide easy and fast drawings.
INSTALLATION GUIDE
15
2
16
Navigation
INSTALLATION GUIDE
CHAPTER
3
Create a Drawing
3
In this chapter:

JumpStart Drawing

Drawing Operations
This chapter provides a tutorial that will
get you up-and-running with
PipeDesigner 3D very quickly.
The instructions in this chapter assume
that you have a compatible Autodesk
application and the PipeDesigner 3D
software open on your computer.
INSTALLATION GUIDE
17
3
Create a Drawing
JumpStart Drawing
These exercises require that you have access to the JumpStart Drawing, which can be
found in the following locations:
• In the PipeDesigner 3D Help folder installed on your computer
• On the PipeDesigner 3D installation DVD in the Manuals folder
Depending on where you are obtaining the drawing from, complete the appropriate
procedure below.
Help Folder
For easy access, the JumpStart Drawing is automatically installed into the PipeDesigner
3D Help folder.
Windows® Vista®/ Windows® 7® Operating Systems
[Drive Letter]:\ProgramFiles\QuickPen\PD3D\Help
B
Tip – If you installed PipeDesigner 3D into a location other than the default,
your folder may be located elsewhere.
Installation DVD
If you are obtaining the drawing from the installation DVD, proceed as follows.
1. Insert the PipeDesigner 3D Installation DVD into the appropriate drive of your
computer.
2. Depending on your computer settings, the installation may not start automatically.
If it does not start a few seconds after you insert the compact disk,
– Double-click on the Computer icon.
– Locate the drive containing the PipeDesigner 3D Installation DVD.
– Click on it to display the PipeDesigner 3D installation window.
– Choose Explore > Installation Disk. This opens a Windows Explorer window.
18
INSTALLATION GUIDE
Create a Drawing
3
3. Navigate to the Manuals folder and right-click on the PD3D_JumpStart.dwg file.
Copy it to a location on your computer. Make note of the location you are copying
the file to. You will need to know this in order to complete the exercises in this
chapter. Trimble recommends that you copy the file to your Windows Desktop for
easy access during the tutorial.
B
Tip – Depending on your computer settings, the file extension (dwg) may not
display. If that is the case, click on the PD3D_JumpStart file and proceed with
the copy process.
4. Close the Windows Explorer window.
5. In the PipeDesigner 3D Installation screen, click Exit.
Drawing Operations
The JumpStart drawing includes a floor, two pumps, a vessel, and a tank. Pipe and
fittings connect the tank to the pump suction. This exercise walks you through the
steps to connect pipe and fittings between the vessel and the pump discharge and
between the vessel and the tank.
1. In the main PipeDesigner 3D application window, click the Open button on the
Quick Access Toolbar.
2. In the Select File dialog, navigate to the location of the JumpStart drawing file.
INSTALLATION GUIDE
19
3
Create a Drawing
Note – This file installs into the Help folder within your PipeDesigner 3D program
folders. Double-click on it
B
Tip – Depending on your computer settings, the file extension (dwg) may not
display. If that is the case, click on the JumpStart file in the Select File dialog.
20
INSTALLATION GUIDE
Create a Drawing
3
The JumpStart drawing now displays in the PipeDesigner 3D window.
If you do not see the entire layout:
Double-click on your mouse wheel.
OR
Enter the Zoom Extents command at the command line:
z and then press Enter
e and then press Enter
INSTALLATION GUIDE
21
3
Create a Drawing
User Coordinate System
Verify that the XYZ axes are oriented properly. Proceed as follows:
1. Go to the AutoCAD Home / Coordinates.
2. Choose World from the list. .
OR
At the command line:
Type ucs and press Enter.
Type w and press Enter.
This will orient the XYZ axes to the World Coordinate System.
Save Drawing File
1. Click on the Menu Browser button
.
2. Choose File / Save As and enter the file name Pumps.dwg.
3. In the Save Drawing As dialog, click the Save button.
Smart Connectivity
The PipeDesigner 3D software uses smart-connectivity, allowing automatic connection
between items when placing these in your drawings. These connections are based on
definitions in the PipeDesigner 3D Data Editor.
• If items do not connect together properly or nothing is yet connect,
displays.
• When you connect an item to another, and it is a “connectable” item, the graphic
no longer displays.
22
INSTALLATION GUIDE
Create a Drawing
3
You will notice the “not connected” graphic in many of the fittings in the JumpStart
Drawing. All items, as presented in the tutorial, will connect properly. Once you have
connected items together, you should no longer see the graphic at the connection
point.
B
Tip – Additional connection features are available in the PipeDesigner 3D
software; however, these are not covered in this Guide. Refer to the online help
system for detailed information.
AutoCAD Options
Options are set on the Status Bar located at the bottom main window.
The following options should be turned on.
Polar Tracking
Object Snap
Object Snap Tracking
When these commands are active, the button displays in a light blue color (default) as
illustrated in the graphics above
Model
All other options should be set to the Off position (dimmed).
INSTALLATION GUIDE
23
3
Create a Drawing
Parts List
The Description pane displays on the left-side of the main PipeDesigner 3D window.
The parts list is dynamic, changing to display the parts available for a selected
system.Parts Lists are assigned to Systems in the Data Editor. For this tutorial, we will
be using the Generic System.
Note – This is the PipeDesigner 3D software default system and all Parts Lists are
assigned to it.
If the panel is not currently displayed, you can open it by clicking on the PD3D™ Tools
ribbon / Show/Hide and then selecting the PD3D Dashboard checkbox.
24
INSTALLATION GUIDE
Create a Drawing
3
Vessel Tasks
Connect Pump Discharge to Vessel
The pipe going into the vessel is 4” pipe, but the nozzles on the vessel are 3" flanged
nozzles. This exercise will show you how to add flanges to the nozzles and then
increase the size to 4" to attach the pipe from the pumps.
Before you begin, select or verify the following settings on the PD3D™ Dashboard /
Parts tab.
1. If not already the default, set the System to Generic.
2. Set the Parts List to 150LB.
3. Set the Main size as 3".
4. Insulation is assigned to this System by default (as noted by
insulation needs to be turned off.
. For this exercise,
– Click the Details tab.
INSTALLATION GUIDE
25
3
Create a Drawing
– Clear the Apply Insulation checkbox.
– Click the Parts tab. The icon should now display in the off position
26
.
INSTALLATION GUIDE
Create a Drawing
3
Connect Flanges to Vessel Nozzles.
1. Place the cursor over the vessel and scroll the mouse wheel to zoom in on the
vessel so you can see both nozzles.
2. Before proceeding, you need to set the PipeDesigner 3D running Osnap.
Note – PipeDesigner 3D has a running Osnap setting separate from the AutoCAD
running Osnap.
– Right-click within drawing space and from the pop-up menu select
PipeDesigner 3D Tools / Osnap Overrides.
3. Select the Node checkbox and then click OK.
B
Tip – PipeDesigner 3D entities snap together by nodes.
INSTALLATION GUIDE
27
3
Create a Drawing
4. From the parts list, select FLANGES/BLINDS > FLG, RFWN 150LB by clicking and
then moving your cursor to modelspace. The fitting displays on screen; however it
has not been placed yet.
5. By default, the cursor is on the buttweld side of the fitting. Right-click and select
Next basepoint to switch to the insertion points on the flange face.
6. Move the cursor toward the center of the upper nozzle until the node displays.
Node
B
Tip – You might find it easier to place items by zooming in closer on the object
with which you are working.
28
INSTALLATION GUIDE
Create a Drawing
3
7. Left-click one time. The Select a connection part window opens. Click on GASKET
AND MACHINE BOLT SET.
8. Click OK. The fitting is placed on the nozzle.
9. To place the flange on the second vessel nozzle, repeat steps 4 through 7.
Connect Concentric Reducers
To see reduction fittings, you must first set the sizes to a reduction size.
1. Modify the setting for Main to 4".
2. Set the Reduction field to 3".
The display should look like the graphic below:
INSTALLATION GUIDE
29
3
Create a Drawing
Place the reducers
1. Click on BW REDUCERS > REDUCER, CONC S/STD from the parts list and then
move your cursor to modelspace.
2. Right-click on the fitting and select Next basepoint to switch to the 3" side of the
reducer, and move the cursor towards the center of the flange on the upper nozzle
to place it at the node.
3. Left-click once to place the reducer at the flange.
4. To place the reducer on the lower nozzle flange, verify that your settings are still as
in the PD3D™ Dashboard graphic above.
5. Once you have verified the settings and made any required modifications, repeat
steps 1 through 4. You drawing will now look as in the graphic below.
30
INSTALLATION GUIDE
Create a Drawing
3
Reduction Tee
You will now place a reduction tee with the following parameters:
• Elevation of 8'0" (96") directly above the discharge of Pump #2.
• Connect a concentric reducer to the tee facing towards Pump #1.
Procedure
1. Execute the Zoom Extents command to display the entire layout.
2. Zoom in on the two pumps.
Pump #1
Pump #2
INSTALLATION GUIDE
31
3
3. In the PD3D™ Dashboard, click
Create a Drawing
to reveal additional options.
4. If a value displays in Reduction, click
next to the field to clear it.
5. Set the Main size to 4” and Branch to 3”.
6. From the parts list, click on BW TEES > TEE, RED S/STD and move your cursor to
modelspace.
32
INSTALLATION GUIDE
Create a Drawing
3
7. Right-click and then click Enter. The cursor should be in the center of the tee. If it is
not, right-click until it is.
8. Click on the PD3D™ Draw ribbon and then choose the XY filter. This allows you to
set the tee at the proper elevation.
9. To set the XY location, move the cursor to the outside edge of the flange on Pump
#2 until the node (at the center) is displayed. Left-click one time.
10. At the command line, enter 96. This sets the reducing tee 96” above the flange.
11. To place the tee in the correct orientation to the pump, move the cursor (from the
just-placed tee) in the same direction as the X axis. Left-click.
INSTALLATION GUIDE
33
3
Create a Drawing
12. Rotate the branch by moving the cursor to the node at the flange on the pump
discharge. Left-click.
13. In the PD3D™ Dashboard, clear the branch value by clicking the red X next to the
Branch field. Select 3 in the Reduction field.
14. Select BW REDUCERS > REDUCER, CONC S/STD from the parts list. Move the
reducer to the node on the reducing tee facing Pump #1. Left-click.
34
INSTALLATION GUIDE
Create a Drawing
3
90-degree Elbow
You will now place a 90-degree elbow above Pump #1 at the same elevation as the
reducing tee.
1. Set the Main size back to 3. Make sure no other fields contain values.
2. Select BW ELBOWS > 90 ELL, LR S/STD, then right-click and click Next basepoint to
move the cursor. You may need to right-click one more time to move the cursor to
the center of the elbow.
3. To set the elbow above the pump discharge at the proper elevation, choose the XY
filter.
4. Move the cursor to the node on the flange above the pump discharge on Pump #1.
Left-click one time.
5. The command line needs a Z (elevation). Enter 96 to set the elbow 96" above the
floor (0 elevation).
6. Move the cursor to the node at the reducer above Pump #2. Left-click. This orients
the elbow in the direction of the reducer.
7. Click the node on the flange at the discharge of Pump #1. This places the elbow
correctly in relation to the pump.
INSTALLATION GUIDE
35
3
Create a Drawing
Place Pipe
The next procedure runs the pipe between the pumps and the upper nozzle on the
vessel.
1. Double-click PIPE > S/STD SMLS and move the cursor with the pipe onto
modelspace.
2. Place the pipe at the node at the top of the flange at the discharge of Pump #1.
Left-click.
3. Move the cursor to the node at the elbow facing the pump. Left-click to place the
pipe between the flange and the elbow.
4. Right-click to Repeat QPEN_DRAWFITTING and place the pipe between the elbow
and the reducer.
5. Right-click to Repeat QPEN_DRAWFITTING and place the pipe between the
discharge of Pump #2 and the reducing tee.
Step 4
Steps 2 and 3
Step 5
36
INSTALLATION GUIDE
Create a Drawing
3
Connect to Vessel
You will now place pipe and fittings between the upper reducer on the vessel and the
reduction tee above the pump. In this exercise, pipe and fittings will be placed
between the two fittings, allowing the PipeDesigner 3D application to determine size
and dimensions.
1. Change the size to 4".
2. Right-click in space; and choose PipeDesigner 3D Tools / Create Router Line.
3. Select the endpoint on the end of the vessel’s upper reducer.
4. After selecting the node, click the PipeDesigner 3D Match Y filter on the PD3D™
Draw ribbon.
PD3D™ Draw ribbon
Match Filters
5. The command prompt needs an entry for the Y dimension. Since you do not know
the exact dimension, select the endpoint on the reduction tee.
INSTALLATION GUIDE
37
3
Create a Drawing
6. Select the PipeDesigner 3D Match Z filter and again select the endpoint on the
reduction tee to set Z (elevation).
7. Click on the endpoint again to determine the final point of the router line.
8. Press [Enter] or [Esc] on your keyboard to finish routing the pipe.
9. Right-click in space and navigate to PipeDesigner 3D Tools / Auto Router / Pipe
and Fittings. Click on the router line.
10. In the Select a part from Parts List dialog, click 90 ELL, LR S/STD and then click the
Always use selected fitting checkbox.
11. Click OK. The pipe and fittings are automatically routed.
38
INSTALLATION GUIDE
Create a Drawing
3
Set Remaining Pipe and Fittings
The last part of this exercise is to run pipe and fittings from the bottom reducer on the
vessel to the top of the tank.
1. Open the PD3D™ Draw ribbon and click Create Route.
2. Start a router line on the lower reducer on the vessel by clicking on the endpoint
inside the reducer.
INSTALLATION GUIDE
39
3
Create a Drawing
3. On the PD3D™ Draw ribbon, click the Match Y filter.
4. Right-click on the Osnap button
and select Settings from the pop-up menu.
The Drafting Settings dialog opens. Click the Quadrant checkbox and then click
OK.
40
INSTALLATION GUIDE
Create a Drawing
3
5. Choose the quadrant on the west side of the tank (the second ring from the inside)
for the Y dimension.
6. Choose the PipeDesigner 3D Match XY filter.
7. Click the same Quadrant you selected in Step 5 above.
8. Click the Match Z filter.
INSTALLATION GUIDE
41
3
Create a Drawing
9. Click the Quadrant at the top of the tank.
Press [Esc] or [Enter] to end the route line.
10. On the PD3D™ Draw / Route ribbon, click Auto Route.
11. Click anywhere on the router line. The Select a part form Parts List dialog opens.
Click on 90 ELL, LR S/STD and then click Always use selected fitting checkbox.
Click OK. The pipe and fittings are routed.
42
INSTALLATION GUIDE
Create a Drawing
3
The pipe/fittings are routed based on your selection. Your drawing will now
look similar to the illustration below.
12. Right-click on the Osnap button
and select Settings from the pop-up menu.
The Drafting Settings dialog opens. Clear the Quadrant checkbox and then click
OK.
Add Remaining Elbows
1. From the Parts List, click BW ELBOWS > 90 ELL LR S/STD.
– Place by the node of the outside edge of the pipe at the top of the tank.
INSTALLATION GUIDE
43
3
Create a Drawing
– Rotate the other end towards the center of the tank to 180° using POLAR.
– Click the left mouse button to place the elbow.
2. Right-click to Repeat QPEN_DRAWFITTING.
3. Rotate the elbow so it points into the tank (270°).
Left-click to place the second elbow.
4. Save the drawing.
44
INSTALLATION GUIDE
Create a Drawing
3
Completed Drawing
Upon completion, the drawing will look like this:
INSTALLATION GUIDE
45
3
46
Create a Drawing
INSTALLATION GUIDE
CHAPTER
4
Additional Features
4
In this chapter:

Part Query

Bill of Material (BOM)

Plot the Drawing
The PipeDesigner 3D software included
several additional features that allows
you to obtain information about your
drawing, such as Part Query and Bill of
Materials. You can also Plot the drawing.
This chapter covers these options.
INSTALLATION GUIDE
47
4
Additional Features
Part Query
You can, at any time, query a part in your drawing. Proceed as follows:
1. Go to PD3D™ Annotate > Tools and click Part Query.
2. Click on the desired part in the drawing. The Part Query window opens.
This dialog displays the part name, drawing class and system based on your selections
when creating the drawing.
Additional features are available; however for purposes of this tutorial, no other
action is necessary. Refer to the online help system for additional information.
48
INSTALLATION GUIDE
Additional Features
4
Bill of Material (BOM)
The PipeDesigner 3D software also allows you to create a BOM. The BOM uses
AutoCAD tables. This allows you to customize the defaults within your template. You
can also edit/customize the table after creating, maintaining links to items.
1. Change your view to Paperspace
.
2. Go to PD3D™ Tools > Spool/BOM > BOM. Click Create. The Bill of Material window
opens.
This window allows you to select the data you want included in the BOM.
INSTALLATION GUIDE
49
4
Additional Features
3. Select the following option buttons:
– Fittings Only
– Total Length
4. Leave the defaults in the BOM Title Text Options and BOM Column Header Text
Options panes.
5. For this exercise, only basic information will be included in the BOM. In the BOM
Field List pane, clear all checkboxes except the following:
– Quantity
– Length
– Description
– Size
6. Click OK.
7. Select the items in your drawing that you want to include in the BOM. Press [Enter]
on your keyboard.
8. The BOM displays on-screen. Place it where you want it and then left click. This
places the BOM in the selected location.
9. You now must set your corresponding balloons.
Additional features are available for the BOM. Refer to the online help system to learn
more.
50
INSTALLATION GUIDE
Additional Features
4
Plot the Drawing
Once you have successfully completed the drawing, you may want to plot the drawing.
Procedure
To plot your drawing, proceed as follows.
1. Open the Pumps drawing file created in the previous chapter.
2. On the Quick Access Toolbar, click
.
INSTALLATION GUIDE
51
4
Additional Features
3. In the Plot - Model dialog, click the Printer/plotter > [Name] where you want to
plot.
B
Tip – It is not necessary to add a Page Setup for this exercise.
– Verify the paper size for the plotter you have chosen.
– Confirm that Plot scale > Fit to paper is checked.
– Click OK.
The image will plot at the chosen plotter.
52
INSTALLATION GUIDE
L