QUOTE FORM
HOT TAPPING & PLUGGING
CONTACT
DATE
TELEPHONE
CUSTOMER
EMAIL
PROJECT NAME
LOCATION
QUANTITY NEEDED
FITTING NEED DATE
SERVICE NEED DATE
FITTING DETAILS
HOT TAP
FITTING
SURELOC ®
3-WAY TEE
SURELOC ® DOUBLE
HUB FITTING
SURELOC ®
FLOWTHROUGH
PLUG
SCARFED
NIPPLE PLUG
SURELOC ®
LINE STOP
FITTING
ANGLED
FITTING
SURELOC ®
SPHERICAL FITTING
SOLID
COMPLETION
PLUG WITH
GUIDE BARS &
SIDE OUTLETS
SOLID
COMPLETION
PLUG
EXISTING PIPE INFORMATION
NPS
HEADER PIPE SIZE
DN
HEADER MATERIAL- SPECIFICATION & GRADE
WALL THICKNESS
IN
FLANGE RATING
150
300
SUITABLE FOR SOUR SERVICE
YES
NO
600
MM
DESIGN CODE
B31.3
B31.4
B31.8
OTHER
DESIGN FACTOR- (required for ASME B31.4/8)
0.72
0.60
0.50
0.40
DESIGN PRESSURE
PSI
BAR
OTHER
DESIGN TEMPERATURE
OTHER
MAX
F/
C
MIN
F/
C
CORROSION ALLOWANCE
IN
MM
FITTING DESIGN INFORMATION
FITTING RUN LENGTH
STANDARD
SPECIAL
FITTING BRANCH SIZE
NPS
FITTING BRANCH SCHEDULE
STANDARD
SPECIAL
STANDARD (raised face)
FITTING FLANGE FACE
NPS
SIDE OUTLET SIZE (if applicable)
MM
IN
MM
IN
MM
DN
SPECIAL
FITTING BRANCH HEIGHT (from CL of run)
IN
RTJ
OTHER
DN
SIDE OUTLET ORIENTATION (if applicable)
PARALLEL
PERPENDICULAR
SIDE OUTLET SCHEDULE (if applicable)
STANDARD
SPECIAL
BACKING STRIPS
YES
COATING
STANDARD (primer)
BEVELED ENDS
YES
IN
MM
NO
OTHER
NO
ADDITIONAL REQUESTS
MATERIAL REQUEST
YES, NACE REQUIRED
3rd PARTY INSPECTION
CARBON EQUIVALENT (CE) MAX
YIELD STRENGTH
%
NO PRESSURE TEST
HOLD TIME
MATERIAL ORIGIN
TEST PRESSURE
PSI
MATERIAL TOUGHNESS
MAXIMUM HARDNESS
Q.A. REQUEST
SHOP TEST
FT-LB at
°F
JOULES at
°C
BAR
kPA
EXTRAS
BLIND FLANGE:
GRADE
STUDS/NUTS:
GRADE
GASKET:
GASKET TYPE
FITTING NOTES
Copyright © 2021 WeldFit.
QUOTE FORM
HOT TAPPING & PLUGGING
SERVICE DETAILS
PRODUCT IN PIPELINE
GAS
ADDITIONAL SERVICE OPTIONS
CRUDE
WATER
NGL
PROPANE
BUTANE
OTHER
IF GAS, WOULD YOU LIKE TO INCLUDE RECOMPRESSION SERVICES IN LIEU OF VENTING OR FLARING ?
YES
NO
IN-SERVICE WELDING?
YES
NO
OPERATING PRESSURE
PSI
OPERATING TEMPERATURE
ETHANE
BAR
OTHER
MAX
°F/
°C
MIN
°F/
°C
LINE DETAILS
SEAMED, SEAMLESS, SPIRAL-WOUND
FLOW RATE
MAIN LINE ORIENTATION
TAP EQUIPMENT ORIENTATION
LINE PIGGABLE (YES/NO)
PIPE COATING / LINING
BRANCH DETAILS
BRANCH LENGTH
(B)
CLEARANCE BEYOND VALVE
(D)
D
ABOVE/BELOW GROUND LEVEL
F
BRANCH ORIENTATION
E
VALVE DETAILS
VALVE TYPE
VALVE LENGTH
A
(C)
FACE TO TOP OF GATE
(E)
VALVE INSIDE DIAMETER
(F)
C
B
GENERAL DETAILS
TOP OF PIPE TO TOP OF VALVE
(A)
MINIMUM BORE OF BRANCH OR VALVE
PLUGGING DETAILS
PURPOSE OF ISOLATION
TYPE OF OPERATION
SINGLE
DOUBLE
BYPASS REQUIRED
YES
NO
TEMPORARY
PERMANENT
DOUBLE DOUBLE
TRIPLE
BYPASS SIZE
BYPASS TYPE
DISTANCE BETWEEN ISOLATIONS
VENT/ PURGE/ DRAIN SIZE
ORIENTATION OF LINE STOP EQUIPMENT
LENGTH OF PIPE AVAILABLE
DURATION OF ISOLATION
SERVICE NOTES
Copyright © 2021 WeldFit.