1. Packing List
2. General safety information
INSTALLATION
INSTRUCTIONS
FOR DK754
REAR WIPER
This symbol means ATTENTION! YOUR SAFTY IS INVOLVED. The message that follows the symbol contains important information
about safty. Carefully read the message.
2
6
7
1
15
4
3
17
16
8
10
12
11
7
8
5
9
1. Packing List
12
18
13
14
2. general safety information
3. HOW TO INSTALL THE REAR WIPER
D.D PART#. T4935-A13080101
KIOTI PART#. 322950
S59S024A
NO PART NO.
1
2
3
4
5
6
7
8
9
T4935-54211
T4930-69492
T4815-88211
T4815-89141
T4815-89151
T4620-81842
T4520-87402
02751-50080
01025-50612
DESCRIPTION
wiper switch(r)
wire harness
wiper motor ass’y(r)
bracket a
bracket b
cushion bolt
packing 1
flange nut
bolt
Q'TY NO PART NO.
1
1
1
1
1
2
2
3
2
10
11
12
13
14
15
16
17
18
T4815-89161
01125-50818
T4815-93211
T4815-89171
t4815-89131
T4815-88221
T4815-82431
T4815-78111
01754-50816
DESCRIPTION
cover
bolt
nut cap
grommet
wiper hose(r)
wiper arm(r)
brush(f)
grommet
flange bolt
BEFORE SERVICE AND REPAIR
1. Read all safety instructions in this
manual and be aware of safety decals
locations on your machine.
2. Thoroughly clean your work area and
machine.
3. Make sure the machine is on firm
and level ground and that the parking
brake is set.
4. Lower the implement to the ground.
5. Stop the engine and remove the key.
6. Disconnect the negative battery cable.
7. Place a “DO NOT OPERATE” tag in
the operator station.
Q'TY
1
2
4
1
1
1
1
1
1
WORKING SAFELY
1. Do not operate or service the machine
while under the influence of alcohol,
medications, or other substances.
2. Never wear loose fitting clothing
and always use safety equipment
appropriate to the job.
3. Never use improvised tools, parts or
procedures. Use only recommended
tools appropriate to the work.
4. Extra care should be taken to work
safely when servicing is done by two
or persons.
5. Always support the machine with
safety stands rated for the weight of
this machine. Never work under a
machine that is supported solely with
a jack.
6. Do not touch any rotating or hot parts
while the engine is running.
7. Escaping fluid (hydraulic oil) under
pressure can penetrate the skin
causing serious injury. Relieve pressure before disconnecting hydraulic or
fuel lines. Tighten all connections
before applying pressure.
DISPOSING OF FLUIDS PROPERLY
1. Observe relevant environmental
protection regulations when disposing
of oil. Never pour fluids onto the
ground, down a drain, or into any
stream of water.
1. Park this tractor on firm and level
ground. Then, engage the parking
brake after stopping the engine.
S59S026A
KIOTI TRACTOR DIVISION /DAEDONG-USA, INC.
6300 Kioti Dr. Wendell, NC 27591
Toll Free:1877 GO KIOTI
Tel:1-919-374-5100 Fax:1-919-374-5001
http://www.kiotitractor.com
OVERSEAS SERVICE DIVISION / DAEDONG INDUSTRIAL
Co.,Ltd.
1-12, BUKRI, NONGONG, DALSUNG-GUN, DAEGU, KOREA
Tel:82-53-610-3350 Fax:82-53-610-3359
http://www.daedong.co.kr
Printed in Korea. Jan.2009
S59S028A
4. Pass the wiper hose (A) through the
hole of rear left pillar to the hole
of fender, and after connecting the
wiper motor's wire harness with the
main wire harness connector (B) in
the roof.
And put it with the wiper hose to the
indoor through the passing hole of the
roof.
S59S025A
2. Remove the rubber caps on the rear
window.
S59S029A
5. After inserting the cushion bolt (6) and
grommet (13, 17) into the mounting
hole of rear window from the rear of
the tractor, install the brackets A (4), B (5) and send the wiper hose outside
through the hole of rear window.
S59S030A
6. After fixing the wiper motor (3) tighten
the bolt, connect the connector.
S59S027A
3. Detach the roof front cover (A) by
loosening the fixing screw (5EA)
and bolts (4EA).
After loosening the roof mounting bolts
(Front 2EA, Rear 2EA), and make a
space by lifting and pushing forward
the roof (B).
Next page▼
S59S031A
S59S032A
S59S034A
7. Tighten the bolt after attach the cover,
install the cap.
S59S036A
S59S037A
10. Detach the wiper motor switch panel 11. Re-install the cabin roof in reverse
order of the disassembly.
using a (-) driver, as shown in the
picture, after inserting the supplied
switch (1) and connecting the wiring
※The indicating number in the picture
connector, re-install the cover.
is in accordance with the ref.number
in the packing list.
S59S033A
8. Insert the wiper hose (14) to the wiper
(16) as shown in the picture, and after
inserting it to the wiper motor shaft,
tighten the nut (A) and close the cover.
S59S035A
9. Pull out the wiper hose through the
left side fender rear hole (A), and
remove the washer reservoir cover.
Insert the hose to the pump (B) and
re-install the cover.