HYVA CYLINDER
FRONT-END CYLINDER WITH OUTER COVER
Hyva
type:
part number cylinder only:
1)
tipping weight :
page # 1 / 2
angle 29o = max. movement of ram
FC 162 - 4 - 04140 - 000
015 01 732
50 tons
mounting instructions on request
clearance for servicing
50
HOLE PATTERN
D
C
A
A1
70
Ø57
G*
412
76
127
102
45
16.5
76
35
35
76
204
I
F
17
L
Ø57
Ødb
70
368
B1 31
B
brackets
:
:
:
:
:
:
:
:
:
FC 162 - 4 - 04140 - 000
4
4140 mm
309
kg
260
kg
64
L
57
L
190
bar (max.)
see oil specification sheet
stage
464
340
382
239
229
242
267
200
1251
1327
85
343
190
187
( not included )
chassis bracket
lifting bracket left hand
lifting bracket right hand
1)
:
:
:
:
:
:
:
:
:
:
:
:
:
:
* incl. 20 mm pull out (p.o.);
tolerances +20 -0
324
specification
type number
number of extensions
total stroke
weight incl. brackets
weight cylinder only
total volume
working volume
operating pressure
oil
32
102
159
216
241
16.5
E*
1"B.S.P.
H*
max. 29
o
K*
260
A
A1
B
B1
C
D
E*
F
G*
H*
I
K*
L
db
All mounting bolts and self-locking
nuts, size M16 (DIN 931.Q8.8).
Washers 17 x 30 mm (DIN 125B).
Max. 2 mm clearance between brackets
and cylinder. Locating plates to be
welded after bolting the brackets.
: 015 06 043
: 015 06 705
: 015 06 717
tipping weight = net weight body + payload.
This Hyva cylinder is designed as a lifting device only.
It must not be used as a structural member or be subject to side
loads and/or abnormal conditions.
Pump flow in consultation with Hyva engineering department
1
2
3
4
effective diameter (mm)
162
141
120
99
stroke (mm)
1005
1025
1055
1055
4140
21
16
12
8
57
oil displacement (L)
total
calculation of the tipping weight
The calculation as shown is based on the following data:
working pressure
: 190
bar (max.)
body length (BL)
: 5350
mm
vertical distance between
centre of gravity
body and payload
and rear hinge of
body (X)
: 650
rear overhang (OH)
: 500
Zo = BL / 2 - OH
Qo = BL + C - OH (pivot)
At = stroke x 60
Qo
mm
This table shows the relationship between body length, rear
overhang and tipping weight1) (tons) and also gives the final
angle of tip. Calculation based on working pressure of 190 bar.
BL
OH
At
Ycog
200
45
600
900
1200
44
48
54
5400
500 800
48
51
50
57
66
59
71
87
200
45
44
49
55
5350
500 800
48
52
50
58
67
60
72
200
46
44
49
55
5300
500 800
49
52
51
58
68
61
74
mm
subject to change without notice
DO-E 01501732 / 04 05 28 / RV AB
HYVA CYLINDER
FRONT-END CYLINDER WITH OUTER COVER
Hyva
type:
part number cylinder only:
1)
tipping weight :
page # 2 / 2
1
31
21
2
3
4
5
6
7
FC 162 - 4 - 04140 - 000
015 01 732
50 tons
41
51
61
62
22
32
42
52
23
33
43
53
24
34
44
spare part list for cylinder 015 01 732
pos.
1
2
3
4
5
6
7
21
22
23
24
31
code no.
017 60 038 K
017 04 151
017 30 034
017 33 035 K
017 31 038
017 32 559
017 32 055
017 60 040 K
026 28 358
017 50 057 K
017 40 428 K
017 60 051 K
description
packset Ø187/183
B 187 - 1285 - 4/4 - 190
bottom plate Ø187
O-ring base Ø187
locking plate Ø187
washer for bolt
bolt
packset Ø162
S 162 - 1246 - SHP
slider Ø162
snap ring Ø162
packset Ø141
qty.
1
1
1
1
3
6
6
1
1
2
1
1
pos.
32
33
34
41
42
43
44
51
52
53
61
62
code no.
026 50 008
017 50 069 K
017 40 430 K
017 60 063 K
017 15 136
017 50 070 K
017 40 441 K
017 02 890 K
017 26 638
017 50 082 K
017 91 941
017 01 850
description
S 141 - 1246 - SHP
slider Ø141
snap ring Ø141
packset Ø120
S 120 - 1246
slider Ø120
snap ring Ø120
top nut and washer
P 099 - 1248
slider Ø099
O-ring for outer cover Ø242
outer cover Ø242 L.998
repair kit
code no.
017 62 205 K
description
complete cylinder packset
consists of all packsets with packset grease and
O-ring base
for specification see page # 1
subject to change without notice
DO-E 01501732 / 04 05 28 / RV AB
qty.
1
2
1
1
1
1
1
1
1
1
1
1