Uploaded by Ромка

2127979-100 GE Innova-2000 Advantx MP Ph4 X-Ray Generator Pre-inst manual

advertisement
Technical
Publications
2127979–100
Revision 5
Advantx MP Ph4 X–Ray Generator
Pre–Installation Manual
do not duplicate
Copyright 1995, 1996, 2000, 2003 by General Electric Co.
%!* -1! !0 ,,.!%( /+%0 +*/0.1%0 /!(+* (!/ *+.)!/ ! /=1.%0= (!/ ,(1/ /=2<.!/ ( /+1.! ! .5+**!)!*0 .!,.=/!*0! 1* *#!.
(+./-1! (! )*%,1(0!1. !/0 *+* -1(%"%= +1 *+* 2!.0% *! !4,+/%0%+* !4!//%2! 1 .5+**!)!*0 !*0.@*! !/ +))#!/ 9 (+.#*%/F
)!
. +*/=-1!*0 0+10!/ (!/ ,.=10%+*/ +%2!*0 >0.! ,.%/!/ ,+1. =2%0!. -1! (!/ ,!./+**!/ *+* 10+.%/=!/ +1 *+* -1(%"%=!/ 10%(%/!*0 !0
,,.!%( .=*0 %*/% 1* *#!. ,+1. (!/ 10.!/ !0 ,+1. !((!/)>)!/
2*0 $-1! )*%,1(0%+* (!/ ,!./+**!/ -1(%"%=!/ !0 10+.%/=!/ 9 /! /!.2%. ! !0 ,,.!%( +%2!*0 /! .!*/!%#*!. /1. (!/ )!/1.!/ !
,.+0!0%+* =0(%!/ ,. ( +))%//%+* *0!.*0%+*(! ! ( .+0!0%+* %+(+#%-1! **(!/ !+))* 0%+*/ ! ( +))%//%+*
*0!.*0%+*(! /1. ( .+0!0%+* %+(+#%-1! !0 10.!/ *+.)!/ *0%+*(!/
$+1#$ 0$%/ !-1%,)!*0 %/ 1%(0 0+ 0$! $%#$!/0 /0* . / +" !(!0.%( * )!$*%( /"!05 0$! 1/!"1( 4.5 !) !+)!/ /+1.!
+" *#!. %* 0$! $* / +" 0$! 1*10$+.%6! +. 1*-1(%"%! +,!.0+. 4!//%2! !4,+/1.! 0+ 4. %0%+* 1/!/ )#! 0+ $1)* 0%//1!
$!.!"+.! !-10! ,.!10%+*/ )1/0 ! 0'!* 0+ ,.!2!*0 1*10$+.%6! +. 1*-1(%"%! ,!./+*/ 0+ +,!.0! 0$%/ !-1%,)!*0 +. 0+ !4,+/!
0$!)/!(2!/ +. +0$!./ 0+ %0/ . %0%+*
!"+.! +,!.0%+* ,!./+*/ -1(%"%! * 10$+.%6! 0+ +,!.0! 0$%/ !-1%,)!*0 /$+1( ! ")%(%. 3%0$ 0$! !+))!* 0%+*/ +" 0$! *0!.F
*0%+*( +))%//%+* +* %+(+#%( .+0!0%+* +*0%*! %* **(/ 1)!. +" 0$! * 3%0$ ,,(%(! *0%+*( /0* . /
1*-1! !/0! ,.0+ !/0: +*/0.1% + /!#D* (/ *+.)/ ! /!#1.% ):/ !/0.%0/ ( . %%B* +*/0%015! 1* ,!(%#.+ ( /!. )*%,1(F
+ ,+. ,!./+*/ *+ 10+.%6 / + %*+),!0!*0!/ * !4,+/%%B* !4!/%2 ( . %%B* ,1! ! 1/. A+/ ( +.#*%/)+
+. +*/%#1%!*0! /! !!.:* 0+). 0+ / (/ ,.!1%+*!/ *!!/.%/ ,. !2%0. -1! (/ ,!./+*/ %*+),!0!*0!/ + *+ 10+.%6 /
10%(%!* !/0! ,.0+ (+ -1! /!.? 1* ,!(%#.+ ,. (+/ !):/ 5 ,. /? )%/)/
*0!/ ! !"!01. (/ )*%,1(%+*!/ (/ ,!./+*/ $%(%0 / 5 +),!0!*0!/ !* !( 1/+ ! !/0! ,.0+ !!.:* %*"+.)./! /+.!
(/ *+.)/ ! ,.+0!%B* "%& / ,+. ( +)%/%B* *0!.*%+*( ! ( .+0!%B* %+(B#% *(!/ + !+)!* %B*!/ ! (
+)%/%B* *0!.*%+*( /+.! ( .+0!%B* %+(B#% 5 +0./ *+.)/ *%+*(!/
%!/!. ,,.0 !*0/,.%$0 %* /!%*!. 13!%/! /0.!*#/0!* !(!'0.%/$!* 1* )!$*%/$!* %$!.!%0/*+.)!* +$ %* !* ;* !* 1*!F
"1#0!. + !. 1*-1(%"%6%!.0!. !./+*!* 3%. !. 61 !%*!. !"$.!*-1!((! 7!.);8%#! C*0#!*!/0.$(1*# %/0 "E. !* )!*/$(%$!* .#F
*%/)1/ /$; (%$
!/3!#!* /%* $%*.!%$!* ! +./%$0/)8*$)!* !."+. !.(%$ 1) 61 2!.$%* !.* 81*!"1#0! + !. 1*-1(%"%6%!.0! !./+*!* /+($!
!.;0! ! %!*!* + !. /%$ /!(/0 1* * !.! !./+*!* !.!* !/0.$(1*# 1//!06!* 'C**!*
+. *!0.%!*$)! %!/!/ ,,.0/ /+((0! /%$ / -1(%"%6%!.0! 1* !"1#0! ! %!*1*#/,!./+*( )%0 !* #!(0!* !* .%0!.%!* "E. !*
#!"$.(+/!* 0.$(!*!%*/06 1.$ /+.#";(0%#!/ 01 %1) !/ !"0/ . !. *0!.*0%+*(!* +))%//%+* "E. 0.$(!*/$106 2!.F
0.10 )$!* ),"!$(1*#!* !. *0!.*0%+*(!* +))%//%+* "E. 0.$(!*/$106 1* * !.!. *0%+*(!. +.)!*!$C. !*
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
TABLE OF CONTENTS
CHAPTER
1
TITLE
PAGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIST OF EFFECTIVE PAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–1
SECTION 1 – OBJECTIVE AND SCOPE OF THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . .
1–1
SECTION 2 – DESCRIPTION OF THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–1
SECTION 3 – RESPONSIBILITY OF PURCHASER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–2
SECTION 4 – PRODUCT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–2
4–1
Basic product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–2
4–2
Product options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1–3
CHAPTER 2 – ROOM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–1
SECTION 1 – ENVIRONMENTAL REQUIREMENT/LIMITATIONS . . . . . . . . . . . . . . . . . . .
2–1
1–1
Room climate & Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–1
1–2
Equipment heat output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–1
1–3
Immunity to magnetic field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2
1–4
Immunity to electric field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2
1–5
Immunity to electrical fast transients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2
1–6
Immunity to electrostatic discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2
1–7
Immunity to surge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2
1–8
Radiation protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–3
1–9
Mobile requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–3
1–10
Audible noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–3
1–11
Interferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–3
SECTION 2 – STRUCTURAL REQUIREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–4
2–1
Minimum door size requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–4
2–2
Ceiling requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–4
2–3
Floor requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–4
2–4
Wall requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–4
2–5
Seismic area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–5
SECTION 3 – POWER & GROUNDING REQUIREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–8
3–1
Line voltage specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–8
3–2
Line frequency specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–8
3–3
kVA load characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–8
3–4
Line impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–9
3–5
Fuse/Circuit breaker specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–10
3–6
Line regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–10
i
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
TABLE OF CONTENTS (CONT.)
CHAPTER
3
4
5
TITLE
PAGE
3–7
Electrical room circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–10
3–8
Additional electrical conditioning device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–10
PHYSICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1
SECTION 1 – DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1
SECTION 2 – MOUNTING REQUIREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1
SECTION 3 – MOBILE REQUIREMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1
INTERCONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–1
SECTION 1 – GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–1
ADDITIONAL PLANNING AIDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–1
SECTION 1 – SHIPPING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–1
SECTION 2 – TOOLS AND TEST EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–4
ii
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
THIS SERVICE MANUAL IS AVAILABLE IN ENGLISH ONLY.
WARNING
IF A CUSTOMER’S SERVICE PROVIDER REQUIRES A LANGUAGE OTHER
THAN ENGLISH, IT IS THE CUSTOMER’S RESPONSIBILITY TO PROVIDE
TRANSLATION SERVICES.
DO NOT ATTEMPT TO SERVICE THE EQUIPMENT UNLESS THIS SERVICE
MANUAL HAS BEEN CONSULTED AND IS UNDERSTOOD.
FAILURE TO HEED THIS WARNING MAY RESULT IN INJURY TO THE SERVICE
PROVIDER, OPERATOR OR PATIENT FROM ELECTRIC SHOCK,
MECHANICAL OR OTHER HAZARDS.
CE MANUEL DE MAINTENANCE N’EST DISPONIBLE QU’EN ANGLAIS.
AVERTISSEMENT
SI LE TECHNICIEN DU CLIENT A BESOIN DE CE MANUEL DANS UNE AUTRE
LANGUE QUE L’ANGLAIS, C’EST AU CLIENT QU’IL INCOMBE DE LE FAIRE
TRADUIRE.
NE PAS TENTER D’INTERVENTION SUR LES ÉQUIPEMENTS TANT QUE LE
MANUEL SERVICE N’A PAS ÉTÉ CONSULTÉ ET COMPRIS.
LE NON-RESPECT DE CET AVERTISSEMENT PEUT ENTRAÎNER CHEZ LE
TECHNICIEN, L’OPÉRATEUR OU LE PATIENT DES BLESSURES DUES À DES
DANGERS ÉLECTRIQUES, MÉCANIQUES OU AUTRES.
WARNUNG
DIESES KUNDENDIENST–HANDBUCH EXISTIERT NUR IN
ENGLISCHER SPRACHE.
FALLS EIN FREMDER KUNDENDIENST EINE ANDERE SPRACHE BENÖTIGT,
IST ES AUFGABE DES KUNDEN FÜR EINE ENTSPRECHENDE ÜBERSETZUNG
ZU SORGEN.
VERSUCHEN SIE NICHT, DAS GERÄT ZU REPARIEREN, BEVOR DIESES
KUNDENDIENST–HANDBUCH NICHT ZU RATE GEZOGEN UND VERSTANDEN
WURDE.
WIRD DIESE WARNUNG NICHT BEACHTET, SO KANN ES ZU VERLETZUNGEN
DES KUNDENDIENSTTECHNIKERS, DES BEDIENERS ODER DES PATIENTEN
DURCH ELEKTRISCHE SCHLÄGE, MECHANISCHE ODER SONSTIGE
GEFAHREN KOMMEN.
ESTE MANUAL DE SERVICIO SÓLO EXISTE EN INGLÉS.
AVISO
SI ALGÚN PROVEEDOR DE SERVICIOS AJENO A GEMS SOLICITA UN IDIOMA
QUE NO SEA EL INGLÉS, ES RESPONSABILIDAD DEL CLIENTE OFRECER UN
SERVICIO DE TRADUCCIÓN.
NO SE DEBERÁ DAR SERVICIO TÉCNICO AL EQUIPO, SIN HABER
CONSULTADO Y COMPRENDIDO ESTE MANUAL DE SERVICIO.
LA NO OBSERVANCIA DEL PRESENTE AVISO PUEDE DAR LUGAR A QUE EL
PROVEEDOR DE SERVICIOS, EL OPERADOR O EL PACIENTE SUFRAN
LESIONES PROVOCADAS POR CAUSAS ELÉCTRICAS, MECÁNICAS O DE
OTRA NATURALEZA.
iii
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
ATENÇÃO
ESTE MANUAL DE ASSISTÊNCIA TÉCNICA SÓ SE ENCONTRA
DISPONÍVEL EM INGLÊS.
SE QUALQUER OUTRO SERVIÇO DE ASSISTÊNCIA TÉCNICA, QUE NÃO A
GEMS, SOLICITAR ESTES MANUAIS NOUTRO IDIOMA, É DA
RESPONSABILIDADE DO CLIENTE FORNECER OS SERVIÇOS DE TRADUÇÃO.
NÃO TENTE REPARAR O EQUIPAMENTO SEM TER CONSULTADO E
COMPREENDIDO ESTE MANUAL DE ASSISTÊNCIA TÉCNICA.
O NÃO CUMPRIMENTO DESTE AVISO PODE POR EM PERIGO A SEGURANÇA
DO TÉCNICO, OPERADOR OU PACIENTE DEVIDO A‘ CHOQUES ELÉTRICOS,
MECÂNICOS OU OUTROS.
AVVERTENZA
IL PRESENTE MANUALE DI MANUTENZIONE È DISPONIBILE
SOLTANTO IN INGLESE.
SE UN ADDETTO ALLA MANUTENZIONE ESTERNO ALLA GEMS RICHIEDE IL
MANUALE IN UNA LINGUA DIVERSA, IL CLIENTE È TENUTO A PROVVEDERE
DIRETTAMENTE ALLA TRADUZIONE.
SI PROCEDA ALLA MANUTENZIONE DELL’APPARECCHIATURA SOLO DOPO
AVER CONSULTATO IL PRESENTE MANUALE ED AVERNE COMPRESO IL
CONTENUTO.
NON TENERE CONTO DELLA PRESENTE AVVERTENZA POTREBBE FAR
COMPIERE OPERAZIONI DA CUI DERIVINO LESIONI ALL’ADDETTO ALLA
MANUTENZIONE,
ALL’UTILIZZATORE
ED
AL
PAZIENTE
PER
FOLGORAZIONE ELETTRICA, PER URTI MECCANICI OD ALTRI RISCHI.
iv
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
REVISION HISTORY
REV
DATE
REASON FOR CHANGE
0
1
2
3
4
5
May 4, 1995
October 4, 1996
February 05, 1998
October 2000
September 2001
October 2003
Product copy
General review and update
Modified Power Input for Biplane Systems
Modified drawings page 2–7, SPRge50177
Modified Chapter 4 (Interconnections)
Modified Capter 2 Section 3 (SPR BUCge93667)
LIST OF EFFECTIVE PAGES
PAGE
REVISION
Title page
Safety Instruction
5
5
i thru vi
5
1–1 thru 1–4
5
2–1 thru 2–14
5
3–1 thru 3–4
5
4–1 thru 4–2
5
5–1 thru 5–4
5
PAGE
REVISION
v
PAGE
REVISION
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
Page blank
vi
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
SECTION 1
OBJECTIVE AND SCOPE OF THIS MANUAL
This manual only considers preinstallation requirements for Advantx MP Ph4 X–ray
generator equipment. It provides preinstallation data such as site preparation prior to delivery
of an Advantx MP Ph4, product information, environmental and electrical requirements, and
some additional planning aids.
For system requirements, such as room layout, system interconnection, refer to the
appropriate System Preinstallation Manual or MIS Maps.
SECTION 2
DESCRIPTION OF THE PRODUCT
The Advantx MP Ph4 X–Ray generator is provided as a main part of the Vascular System; it
enhances the System by producing X–Ray beam and in room system source of power supply.
It is also provided in Remote R&F room with a Tilt–C gantry.
A basic Advantx MP Ph4 X–Ray generator contains the main parts as follows:
MPPU1 – Cabinet with a X–Ray generator
MPPU2 – Cabinet with an AC distribution panel
MPPU4 – EMC filter (inside MPPU2)
MPPU5 – Micro grid H.V. tank
Independently of X–Ray beam power requested by the uses, it is be supplied for 100 kW. The
Advantx MP Ph4 X–Ray generator can feed two X–Ray tubes as follows:
Mainly a MAXIRAY 150 on positioner,
and a MAXIRAY 100 used with an auxiliary device like long log film changer by
example.
INTRODUCTION
CHAPTER 1 – INTRODUCTION
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
INTRODUCTION
REV 5
pim 2127979–100
SECTION 3
RESPONSIBILITY OF PURCHASER
“Preinstallation” refers to work necessary to plan and prepare a site for installation of an
Advantx MP Ph4 X–Ray generator equipment, whether included in a complete new system
or being added to an existing X–Ray room.
Delay, confusion and waste of manpower can be avoided by adequate preinstallation work,
including:
procurement of required materials,
installation of material required before delivery of Advantx MP Ph4 X–Ray generator,
anticipation of alterations and modifications not already provided in the sales contract,
to match with the ligne resistance requirements or with the NEC table requirements.
SECTION 4
PRODUCT IDENTIFICATION
4–1
Basic product
The Advantx MP Ph4 X–Ray generator includes two cabinets and one H.V. thank inside one
of them.
TABLE 1–1
BASIC PRODUCT
Part
Number
DESIGNATION
MP Ph4 X–Ray generator
including:
2131100–x
Location
of Name Plate
At the top of cabinet
between fans.
MPPU 1 Cabinet–assembly
with 100 kW H.V. tank
(2100418)
MPPU 2 Cabinet–assembly
MPPU 2 Cabinet–assembly
At the top of cabinet
between fans.
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
pim 2127979–100
ILLUSTRATION 1–1
BASIC PRODUCT
Location Identification plates
Legend of Illustration:
Note:
4–2
MPPU1 – Cabinet with a X–Ray generator
MPPU2 – Cabinet with an AC distribution panel
MPPU1 and MPPU2 cabinets are bolted together on site
as showed.
Product options
The option available with an Advantx MP Ph4 X–Ray generator is:
Note:
MPPU5 – Micro grid H.V. tank in Vascular option (P/N 2127280)
The micro grid HV tank is included inside MAXIRAY 150 covers and needn’t
preinstallation requirement.
TABLE 1–2
PRODUCT OPTIONS
Part
Number
2150124–x
DESIGNATION
MP Ph4 Vascular option
LOCATION
of Name Plate
At the top of both
cabinets between fans
INTRODUCTION
REV 5
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
INTRODUCTION
Page blank
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
CHAPTER 2 – ROOM REQUIREMENTS
SECTION 1
ENVIRONMENTAL REQUIREMENT/LIMITATIONS
Room climate & Altitude
CAUTION
Avoid extremes in temperature.
TABLE 2–1
ENVIRONMENTAL REQUIREMENTS/LIMITATIONS
HUMIDITY
PRODUCT/
COMPONENT
In use (1)
Min
Max
Storage
Note:
(1)
(2)
1–2
30 %
80 %
In use (1)
Min
Max
ALTITUDE/PRESSURE
Storage
Min
Max
0%
+16 C +40
+16C
+40C
C –40C
40 C +80
+80C
C
95 %
+61F +104F –40F +176F
MPPU1
Cabinet
MPPU2
Cabinet
TEMPERATURE
Min
Max
In use and Storage
Min
Min
–30 m
–100 ft
+3050 m
+10,000ft
700 hPa
1060 hPa (2)
Non–condensing at 20C (68F)
Atmospheric pressure (hPa = hectoPascal or mbar)
Equipment heat output
The MPPU1 and MPPU2 cabinets have vents for exhaust air on top with 4 fans. Vents for air
input are provided at the bottom of the front panel (See Illustration 3–1).
Note:
It is important that the front panel vents and the top are not obstructed.
2–1
ROOM REQUIREMENTS
1–1
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
TABLE 2–2
HEAT OUTPUT AND AIR FLOW RATE BASIC PRODUCT
HEAT OUTPUT
PRODUCT/
COMPONENT
ROOM REQUIREMENTS
MPPU1 Cabinet
MPPU2 Cabinet
Note:
(1)
In–Use
Stand–By
1,500 W
5100 BTU/h
1,000 W
3400 BTU/h
AIRFLOW RATE (1)
In–Use
Stand–By
480 m3/h
16,950 ft3/h
Maximum of fan’s capacity (total)
TABLE 2–3
HEAT OUTPUT AND AIR FLOW RATE OPTIONS
HEAT OUTPUT
PRODUCT/
COMPONENT
In–Use
MPPU5 Micro grid
H.V. tank
1–3
Negligible
Immunity to magnetic field
Not available at this time.
1–4
Immunity to electric field
According to IEC 601–1–2/IEC 1000–4–3
1–5
3 V/m 30 to 1,000 MHz.
Immunity to electrical fast transients
According to IEC 601–1–2/IEC 1000–4–4
1–6
2 kV on power supply lines,
0,5 kV on signal lines.
Immunity to electrostatic discharge
According to IEC 601–1–2/IEC 1000–4–2
1–7
Stand–By
8 kV air discharge,
3 kV contact discharge.
Immunity to surge
According to IEC 601–1–2/IEC 1000–4–5
2 kV common mode,
1 kV differential mode.
2–2
AIRFLOW RATE
In–Use
Stand–By
Not applicable
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
1–8
pim 2127979–100
Radiation protection
1–9
ROOM REQUIREMENTS
A qualified radiological health physicist should review Vascular or R&F Tilt–C room
shielding requirements while taking into consideration equipment placement, weekly
projected workloads, and materials used for construction of walls, floors, ceiling, doors and
windows.
Mobile requirements
Not applicable.
1–10
Audible noise
Each Advantx MP Ph4 X–Ray generator cabinet emits audible noise limited to 65 dB at 1 m
(3.3 feet).
The micro grid H.V. tank doesn’t emit audible noise.
1–11
Interferences
To avoid any artifacts on monitor screens that could be registered, do not locate the MP Ph4
cabinets close the Image Identifier head where a TV camera is mounted.
CAUTION
The MP Ph4 cabinets will be located at least 1.5 meter (6 feet) as minimum
distance to the Image Intensifier in worst case.
2–3
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
SECTION 2
STRUCTURAL REQUIREMENT
ROOM REQUIREMENTS
2–1
Minimum door size requirements
Access through a door opening of at least 0.6m (25 inches) wide, and of a height at least 2 m
(6.56 ft) is required.
2–2
Ceiling requirements
Not applicable.
2–3
Floor requirements
Each cabinet is placed on the floor, which must accept the weight and the weight/area defined
in table 3–1. The cabinets need not be fixed, but four holes are pre–drilled
(see Illustration 2–2).
2–4
Wall requirements
The cabinets are normally placed close to a wall with a clearance and need not to be fixed, but
two holes are pre–drilled (see Illustration 2–3).
TABLE 2–4
STRUCTURAL REQUIREMENTS
FLOOR MOUNTING
PRODUCT/
COMPONENT
Material
Strength
WALL MOUNTING
Anchor Method
(ref. drawing)
Anchor
Loading
Material
Strength
Anchor Method
(ref. drawing)
MPPU1
Cabinet
Illustration 2–2
2845 N
640 lbs
Illustration 2–3
MPPU2
Cabinet
Illustration 2–2
3188 N
716 lbs
Illustration 2–3
MPPU5
Micro grid
H.V. tank
Not applicable
(1)
(1)
(2)
Not applicable
Notes:
(1)
In seismic area, use adapted seismic kits
(2)
Put on MAXIRAY 150 tube–housing inside covers
2–4
Anchor
Loading
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
2–5
pim 2127979–100
Seismic area
Bottom cabinet, 2 holes diameter 16 mm pre–drilled to accept bolts M12.
Rear cabinet, 2 holes diameter 16 mm pre–drilled to accept bolts M12.
A kit for seismic areas can be supplied by GEMS like an option for cabinets MPPU1 and
MPPU2 under catalog number 45440153 (see Illustration 2–1) with:
–
a bracket with 4 holes pre–drilled to accept bolts M16 diameter,
–
4 washer plates,
–
4 hex screws M16x25 (to mount the bracket on both cabinets).
ILLUSTRATION 2–1
MPPU1 AND MPPU2 CABINETS, KIT FOR SEISMIC AREA
501
(19.72)
54
(2.13)
501
(19.72)
27
(1.06)
(1)
(1)
1110
(43.31)
38
(1.5)
(1)
4
(1)
(0.16)
21
(0.83)
17
(0.67)
27
(1.06)
É
É
É
É
ÇÇÇÇÇÇ
É
ÇÇÇÇÇÇ
É
ÇÇÇÇÇÇ
É
Wall
Cabinet
53
(2.09)
10
∅18
(0.7)
Illustration not to scale
All dimensions are in mm (inches).
4
414
(16.30)
(0.39)
414
(16.30)
40
(1.58)
70.5
(2.78)
(0.16)
625.5
(24.6)
Note : (1)
2–5
Bracket with pre–drilled holes ∅18 (0.7) to accept M16
diameter bolts
ROOM REQUIREMENTS
Following seismic area, use adapted method to fix the cabinets to the floor and/or to the wall.
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
ROOM REQUIREMENTS
ILLUSTRATION 2–2
FLOOR MOUNTING – ADVANTX MP PH4 CABINET ASSEMBLY (MPPU1, AND MPPU2)
39.5
(1.55)
79
(3.11)
39.5
(1.55)
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
476
(18.74)
476
(18.74)
2
3
215
1
2
100
(3.94)
MPPU2
Service area
600 mini
(23.6 mini)
37.5
(1.47)
MPPU1
(8.46)
418
(16.457)
444
(17.48)
100
(4)
1
115
(4.53)
All dimensions are in mm (inches).
Legend of Illustration:
1 – Bottom cabinets: 4 holes ∅16 (0.63) diameter pre–drilled to accept M12 anchor bolts.
2 – No clearance needed back or side cabinets, except if the cables are running through cable access from rear or side.
3 – Floor cable access 100 x 215 mm (4” x 8.5”).
2–6
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
ILLUSTRATION 2–3
WALL MOUNTING – ADVANTX MP PH4 CABINET ASSEMBLY (MPPU1 AND MPPU2)
1
MPPU1
MPPU2
REAR
F
R
O
N
T
97.5
(3.84)
360
(14.17)
510
(20.08)
790
(31.1)
215
(8.46)
850
(33.46)
77.5
(3.05)
220
(8.66)
G2
1553
(61,14)
400
(15.75)
G2
ÉÉÉÉÉ
ÉÉÉÉÉ
1000 mini
(39.37)
345
(13.58)
100
100
(3.94)
G1
277.5
(10.92)
(3.94)
2001
(78.78)
2018
(79.45)
97.5
(3.84)
360
(14.17)
2
3
2
3
G1
222.5
(8.76)
114 (4.49)
See Detail A
555
(21.85)
4
Detail A
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÇÇ
ÉÉÉÉÉÉÉ
ÇÇ
ÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉ
0
26
(1.02)
Wall
1
2
3 ft
1m
444
(17.48)
473
(18.62)
Cabinet
101
0
215
(8.46)
FRONT VIEW
Scale
128
(5.04)
555
(21.85)
(3.98)
77.5
(3.05)
100
(3.94)
294
(11.6)
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
LEFT SIDE VIEW
Floor
All dimensions are in mm (inches).
Aperture for
skirting board
Legend of Illustration:
1 – Seismic kit catalog number 45440153: bracket with 4 pre–drilled holes to accept M16 diameter bolts
2 – Location of bracket fixing holes for Seismic kit
3 – Rear cabinets, 4 pre–drilled holes ∅16 (0.63) diameter to accept M12 anchor bolts
4 – Access cables rear MPPU1 = 400 x 100 mm (15.75” x 4”)
MPPU2 = 215 x 100 mm (8.5” x 4”)
5 – Access cables on right side of MPPU2 = 215 x 100 mm (8.46” x 4”)
2–7
5
ROOM REQUIREMENTS
501
(19.725)
1980
(77.95)
27
(1.06)
1
54
(2.12)
501
(19.725)
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
SECTION 3
POWER & GROUNDING REQUIREMENT
Power, ground and interconnecting cable requirements are covered in the appropriate
Advantx System MIS direction. The direction number for the Advantx System MIS varies
depending upon type of system (e.g. RAD, R&F, VAS).
ROOM REQUIREMENTS
Only WYE (three phase star) main power supply diagrams are allowed. All three phase
DELTA main power supply diagram are forbidden.
Due to a large frequency band, the main circuit breaker with differential must be in
compliance with a type defined by GEMSE and mustn’t disconnect untimely.
From room power distribution panel, just a power cable is supplied by customer.
Advantx MP Ph4 X–Ray generator provides power supply to others X–Ray components
listed in power supply interconnect chapter.
Note:
Route power feeds away from sensitive system cables such as video control and coax
cables which come from the system cabinet or video camera head. The power feed should
never share the same conduit or raceway as any video cable. Even short lengths can cause
significant problems. Dividers in raceways or adjacent conduits or raceways are not
sufficient separation in most instances. Physical separation is the only sure way to
eliminate contamination of the video signal from power line hum.
For Advantx–E systems, maintain a 2 meter minimum distance between the TV1,
TV2 and TV3 cables and the 380 to 480 VAC power line (MIS #10813A) to the MP
Ph4 power unit.
CAUTION
TABLE 2–5
TV CABLE IDENTIFICATION
3–1
SYSTEM TYPE
TV1
TV2
TV3
LCA/LCV+
MIS #11433A
MIS #11434A
MIS #11435A
TC/TCV
MIS #11439A
MIS #11440A
MIS #11441A
Line voltage specifications
Input voltage 3 phases without neutral, 360 Vac to 480 Vac 10% as follows:
3–2
360/380/400/420/440/460/480 Vac.
Line frequency specifications
50 Hz or 60 Hz nominal with a rate of 1%.
3–3
kVA load characteristics
Single plane (one X–Ray generator).
Biplane (two X–Ray generators).
2–8
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
When the system requires two Advantx MP Ph4 for frontal and lateral exposures, the
Maximum instantaneous power will be equal to 200 kVA with an average power demand
equal to 20 kVA. The nominal instantaneous power is not multiplicated by two.
TABLE 2–6
ADVANTX MP PH4 100 POWER SUPPLY
Phase
3
3
3
3
3
3
3
360
380
400
420
440
460
480
10%
10%
10%
10%
10%
10%
10%
Maximum instantaneous power (1) (kVA)
for nominal line voltage
171
171
171
171
171
171
171
Power factor
0.9
0.9
0.9
0.9
0.9
0.9
0.9
Momentary line current (1) (Amp)
for nominal line voltage
274
260
247
235
224
214
205
Continuous line current (Amp)
14
Nominal line voltage (Vac)
Voltage range (Vac)
range
10
Inrush current
Average power demand (kVA) (2)
3–4
15
15
15
15
15
15
15
Note 1:
171 kVA based on momentary power demand in kVA/0.1 second maxi, but to feed other equipments
connected to the room distribution panel, 10 kVA (for single plane systems) or 20 kVA (for biplane
systems) can be added in worst case of utilization. For the Innova 2000 system there is a derating due to the
X–Ray tube main power – See Innova 2000 System Pre–Installation Manual part number 2337741–100.
Note 2:
Change from 15 to 20 kVA for a biplane use.
Line impedance
GEMS Engineering has defined a maximum value of line impedance calculated on nominal
input voltage equal 380 V rms.
If the input voltage has an other value, a table provides the adequate value adapted to the new
input voltage (see table 2–7).
TABLE 2–7
MAXIMUM LINE IMPEDANCE
Apparent resistance of feed circuit
in ohms per 2 phase wires (measured to the B point)
Note:
Input voltage
360
380
400
420
440
460
480
MP Ph4 100
0.09
0.10
0.11
0.12
0.13
0.14
0.16
The impedance of the feeder between the ground bar and the Main ground point
must be less than 2 ohms.
2–9
ROOM REQUIREMENTS
MP Ph4 100
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
3–5
pim 2127979–100
Fuse/Circuit breaker specifications
The main circuit breaker is supplied by the customer and must be sized in
accordance to the local regulation. If the PDP is equipped with a differential
calibrated to 30 mA, the latter must be at least with class A (for pulse waveform
current).
ROOM REQUIREMENTS
CAUTION
For instance with a 380 V, 3 phases, electrical network the circuit breaker may be sized as
follows:
3–6
for MP Ph4 100: thermal circuit breaker = 80 A with a magnetic breaker at
960 A 20%.
Line regulation
To correctly feed a High Frequency X–Ray Generator like the Advantx MP Ph4, the main
characteristics are the limits of the impedance according to table 2–7.
3–7
Electrical room circuit
This chapter has been added to provide additional data regarding power circuit provided by
the customer and internal electrical circuits to supply a correct power to the Tilt–C R/F room
and Vascular room system.
Illustration 2–5 shows the room power supply installed at customer expense with a DMD in
compliance with chapter 3–5.
Illustration 2–6 shows the internal electrical circuit distributed from AC Distribution Panel
inside MPPU2.
3–8
Additional electrical conditioning device
Any electrical conditioning device can be added on power line do feed the Advantx MP Ph4.
Any kind of suppressor filter or regulator will be redundant with the Advantx MP Ph4.
2–10
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
ILLUSTRATION 2–4
ROOM POWER SUPPLY FOR SINGLE PLANE SYSTEMS, INSTALLED AT CUSTOMER EXPENSE
From main ground point.
ROOM REQUIREMENTS
PDP
DMD
C
Ground
bar
Y
E/O
L
MPPU2
B point
GO TO SUBSYSTEMS
Note:
Power and ground are coming from the same distribution panel. They are separated from
any others which generate transients (elevator, air conditioning system, etc ...) and run
near one another.
The armor of any armored cable coming from the distribution panel or an hospital
vault cannot replace the ground cable.
2–11
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
ILLUSTRATION 2–5
ROOM POWER SUPPLY FOR BIPLANE SYSTEMS, INSTALLED AT CUSTOMER EXPENSE
MAINS
From main ground point.
D
ROOM REQUIREMENTS
PDP
C
DMD1
DMD2
Ground
bar
Y
E/O
L
MPPU2
Frontal
MPPU2
B point
Lateral
B point
GO TO SUBSYSTEMS
Note:
GO TO SUBSYSTEMS
Power and ground are coming from the same distribution panel. They are separated from
any others which generate transients (elevator, air conditioning system, etc ...) and run
near one the other.
The shield of any shielded cable coming from the distribution panel or an hospital
vault cannot replace the ground cable.
2–12
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
1
Advantx MP Ph4 is supplied by GEMS with a room Distribution Panel located inside
MPPU2 Cabinet. See Illustration 2–6.
2
Cables are to be provided by customer (inlet to MPPU2 with 2 m (6.56 ft) held over).
PDP
Power distribution panel for powering X–ray equipment (not supplied by GEMS).
DMD1 and DMD2
Note 1:
Thermal–magnetic differential circuit breaker
(see note 1), both mandatory for Biplane Systems
D
Disconnector with fuses
C
Contactor (see note 1).
Y
Contactor remote–control ON/OFF impulse buttons, lockable on ”OFF”, with
indicator lamps (Red = ON/Green = OFF) located near access door, 1.5 m (4.92 ft)
above floor.
E/O
Emergency off button located near access door, 1.5 m (4.92 ft) above floor.
L
Red continuous glow or flashing presence indicator lamp located above the access
door, near LRx. Voltages: 220 V in Europe/120 V in USA with bulb 25 W maxi.
According to national and local code or regulations.
2–13
ROOM REQUIREMENTS
Legend of Illustration 2–4 and 2–5:
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
ROOM REQUIREMENTS
ILLUSTRATION 2–6
INTERNAL ELECTRICAL CIRCUIT FROM MPPU2 CABINET
1
2
3
4
5
6
7
8
9
BA01 CONNECTOR
1234 5 6 1 2 3
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
BA10
1.
2.
3.
4.
5.
6.
7.
8.
9.
In expectation of something.
Positioner 1 – 240 Vac – 1, 560 VA (1 thru 3).
Auxiliary – 240 Vac – 480 VA (4 thru 7).
Positioner 2 – 240 Vac – 1,560 VA (8 thru 10).
Chiller – 120 Vac – 2,200 VA (11 thru 14).
Digital – 240 Vac – 2,760 VA (15 thru 17).
System Cabinet – 240 Vac – 2,192 VA (18 thru 20).
Digital for DLX step down transformer – 360 Vac/480 Vac – 1,000 VA (21 thru 23).
In expectation of something.
Jumper between plug numbers 5 and 6, 12 and 13.
Phase plugs 1, 4, 8, 11, 15 and 18.
Neutral plugs 2, 5 & 6, 9, 12 & 13, 16 and 19.
Ground plugs 3, 7, 10 14, 17, 20 and 23.
Plugs 21 and 22 are uninterrupted by the switch on/off.
2–14
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
CHAPTER 3 – PHYSICAL CHARACTERISTICS
SECTION 1
DIMENSIONS
This chapter provides product information and illustrations showing dimensions, weight,
floor loading, location of center of gravity (CG), mounting holes, and access areas for
servicing and cabling.
The floor loading (weight/area) is calculated from the approximate component weights and
should be considered as a minimal loading.
TABLE 3–1
PHYSICAL CHARACTERISTICS
MPPU1
Cabinet
MPPU2
Cabinet
FLOOR LOADING
REFERENCE
DRAWING
Depth
mm (in)
Width
mm (in)
Height
mm (in)
WEIGHT
Weight/
Area
Load Pattern
(for drawing)
473
555
1980
(18.62)
(21.85)
(77.95)
2845 N
640 lbs
12,932 N
per m2
Illustration
3–2
Illustration 33–1
1
473
555
1980
(18.62)
(21.85)
(77.95)
3188 N
716 lbs
14,491 N
per m2
Illustration
3–2
Illustration 33–1
1
SECTION 2
MOUNTING REQUIREMENT
It is not required to anchor Advantx MP Ph4 cabinets to the floor.
SECTION 3
MOBILE REQUIREMENT
Not applicable.
CHARACTERISTICS
DIMENSIONS
PRODUCT/
COMPONENT
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
300 mini
(12) mini
ILLUSTRATION 3–1
ADVANTX MP PH4 CABINET ASSEMBLY (MPPU1 AND MPPU2) – DIMENSIONS
1
MPPU2
2
G1
277.5
(10.92)
345
(13.58)
FRONT
220
(8.66)
G2
G2
G1
222.5
(8.76)
850
(31.46)
790
(31.1)
CHARACTERISTICS
REAR
1980
(77.95)
MPPU1
3
555
(21.85)
555
(21.85)
473
(18.62)
FRONT VIEW
LEFT SIDE VIEW
Location of
Identification plates
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
TOP VIEW
Scale
0
0
1
2
3 ft
1m
All dimensions are in mm (inches)
Legend of Illustration:
1 – Air exhaust by 4 fans on top of each cabinet
with ventilation grid (do not obstruct).
2 – Cable access.
3 – Air input.
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
50
(2)
25
(1)
555
(21.85)
Scale
0
100
200
300
400
500 mm
0
10
20 inches
All dimensions are in mm (inches)
CHARACTERISTICS
50
(2)
ÉÉÉÉÉÉÉÉÉ
Ç
ÇÇ
ÉÉÉÉÉÉÉÉÉ
Ç
ÇÇ
Ç
ÇÇ
Ç
ÇÇ
Ç
ÇÇ
ÉÉÉÉÉÉÉÉÉ
Ç
ÇÇ
400
(15.75)
25
(1)
ILLUSTRATION 3–2
MPPU1 OR MPPU2 CABINET FLOOR LOAD PATTERNS
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
CHARACTERISTICS
Page blank
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
CHAPTER 4 – INTERCONNECTIONS
SECTION 1
GENERAL
" # ! " ! " 2106464–100 Advantx Tilt–C/Vamp System MIS Maps,
2126032–100 Advantx–E LCA/LC+/LCV+/SC+ System MIS Maps,
2106465–100 Advantx Tilt–C/ System MIS Charts,
2126033–100 Advantx–E LCA/LC+/LCV+/SC+ System MIS Charts,
2261290–100 Innova 2000 Cardiovascular System Mis Maps,
2276549–100 Innova 2000 Cardiovascular System Mis Charts.
INTERCONNECTIONS
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
INTERCONNECTIONS
Page blank
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
CHAPTER 5 – ADDITIONAL PLANNING AIDS
SECTION 1
SHIPPING INFORMATION
This chapter provides Advantx MP Ph4 X–Ray generator shipping information. Table 5–1
gives weights and dimensions for the packaged equipment, and Illustrations 5–1 and 5–2
show the shipping configurations used respectively for truck and air shipment.
TABLE 5–1
PRODUCT SHIPPING INFORMATION
" ! !
#!
&*"/
0 0 0 0 &*"/
0 0 0 0 * ,(("/
&*"/
0 0 0 0 "" *+/"
* ,(("/
+/ .&$*&#& */
*.&!"
& -+ $-&!
/*'
&*"/. -" , '$"! /+$"/%"-
PLANNING AIDS
" &- .%&,)"*/ * ,(("/
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
PLANNING AIDS
2110
(83)
ILLUSTRATION 5–1
MPPU1 OR MPPU2 CABINET SHIPMENT ON PALLET (EUROPE)
1100
(43.3)
800
(31.5)
100
(4)
All dimensions are in mm (inches).
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
ILLUSTRATION 5–2
MPPU1 AND MPPU2 CABINET AIR SHIPMENT
640
(25.2)
PLANNING AIDS
2300
(90.55)
1300
(51.18)
All dimensions are in mm (inches).
GE Medical Systems
Advantx MP Ph4 X–Ray Generator
REV 5
pim 2127979–100
SECTION 2
TOOLS AND TEST EQUIPMENT
See table 5–2, list of tools and test equipment for Advantx MP Ph4 X–ray generators.
TABLE 5–2
REQUIRED TOOLS AND TEST EQUIPMENT
PRODUCT OR
COMPONENT
MP Ph4 80/100
TOOL OR
TEST EQUIPMENT
Service Engineer’s
Tool Case
USED FOR
General use
RECEIVED
(DATE)
SOURCE
Transport equipment
Multimeter Flucke
8060A
Line voltage adjustment
Laptop computer with
parts No.:
– 2103652
– 36005594
Generator calibration
Software
Oscilloscope with
memory two channels
Calibrate heating current
Dosimeter (Radcal)
with 2025 probe
Calibration
Phantom
Fluoroscopy calibration
H.V. pickmeter
H.V. measurement
PLANNING AIDS
2 x 1 mm thick copper
plates
Download