®
System Configuration and Order-information Guide
RX300 S4
March 2009
PRIMERGY RX300 S4
Front View
DVD-ROM Drive
Hard Disk Bay
Back View
PCI Slot (LowProfile)
Power Supply
Power Supply (optional)
Mouse
10/100/1000BASE-T Connector
10/100BASE-TX Connector
(for Remote Management Controller)
Keyboard
Serial Port
Display
Inside View
front side
PCI Slot
System Fan
CPU
Memory Expansion Board
Power Supply
PRIMERGY RX300 S4
Instruction
This document contains basic product and configuration information that will enable you
to configure your system.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server
or your complete PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to meet your specific
requirements.
Please follow the lines. If there is a junction, you can choose which way or component
you would like to take.
Go through the configurator by following the lines from the top to the bottom.
The color of the junction means as follows.
Key to
Or
And
PRIMERGY RX300 S4
Data Sheet
Dual-Processor Rack Server
Type
Model
Base Unit
3.5inch SAS model
Xeon® E5205(1.86GHz) (with TPM)
PGUR3041A3
Xeon® E5205(1.86GHz) (without TPM)
CPU
Frequencies
Second-Level-Cache
PGVR3041A
Intel® Xeon® X5470(3.33GHz) *6 / X5460(3.16GHz) *7 / E5420(2.50GHz) *8 / E5405(2GHz) *9 /
X5270(3.50GHz) *10 / X5260(3.33GHz) *11 / E5205(1.86GHz)
12MB ( Intel® Xeon® X5470(3.33GHz) / X5460(3.16GHz) / E5420(2.50GHz) / E5405(2GHz) ) /
6MB ( Intel® Xeon® X5270(3.50GHz) / X5260(3.33GHz) / E5205(1.86GHz) )
Number of processors
Number of cores
Front-Side-Bus
1 (max. 2)
4 per processor ( Intel® Xeon® X5470(3.33GHz) / X5460(3.16GHz) / E5420(2.50GHz) / E5405(2GHz) ) /
2 per processor ( Intel® Xeon® X5270(3.50GHz) / X5260(3.33GHz) / E5205(1.86GHz) )
1333MHz ( Intel® Xeon® X5470(3.33GHz) / X5460(3.16GHz) / E5420(2.50GHz) / E5405(2GHz) / X5270(3.50GHz) / X5260(3.33GHz) ) /
1066MHz ( Intel® Xeon® E5205(1.86GHz) )
Chipset
Intel® 5000P
standard (onboard) *12 (PGUR3041A3) /
TPM (Trusted Platform Module)
- (PGVR3041A)
Standard
Maximum *1
Graphics Controller
Resolution *2
Internal Bays Number of bays
3.5 inch
Available HDD *3 *4
HDD
(SAS)
Memory
Maximum *3 *4
Internal Backup Device
DVD-ROM
PCI Slots
PCI Express (x4) [x8]
PCI-X (64bit/133MHz) [3.3V]
RAID
SAS / SATA Interface
FDD
Network Interface (onboard)
Interfaces
Server Management Software
1GB (512MB ECC DDR2 SDRAM Fully Buffered DIMM x 2, PC2 5300F) (SDDC(Single Device Data Correction) supported)
48GB (4GB ECC DDR2 SDRAM Fully Buffered DIMM x 12, PC2 5300F) *13
incl. Remote Management Controller, VRAM : 8MB
640x480/800x600/1024x768/1280x1024 dot
6 (hot plug)
3.5inch, SAS, 15krpm, 73.4GB (PG-HDB75A)
3.5inch, SAS, 15krpm, 146.8GB (PG-HDB45A)
3.5inch, SAS, 15krpm, 300.0GB (PG-HDB35A)
3.5inch, SAS, 15krpm, 450.0GB (PG-HDB55A)
2.7TB ( 450.0GB x 6 )
Tape Drv DAT72 36GB internal w/ Drive Cage (PG-DT504D) is available as an option.
(required 2 bays)
Max 8 DVD-ROM / Max 24 CD-ROM (SATA)
6 : LowProfile PCI Express Card Only ( SAS RAID Controller occupies one slot. ) *14 *15
1 : LowProfile PCI Card Only
standard (SAS RAID Ctrl (PG-248B), with RAID0/1/1+0/5/6 function)
SAS x 8ports *16
- *17
2 ports (1000BASE-T/100BASE-TX/10BASE-T)
Display (Analog RGB), Serial Port x 1(D-SUB 9pins) (2 when Serial Port (PG-COM03) is applied.) *14
Parallel Port x 0(D-SUB 25pins) (1 when Parallel Port Option (PG-PP05) is applied.) *15
Keyboard (PS/2type Mini DIN 6pins), Mouse (PS/2type Mini DIN 6pins), USB x 5 (ver. 2.0) (Internal : x 1,External : x 4)
ServerView (Standard)
standard (onboard, Remote Management Controller)
Remote Service function
Power supply
connector
Voltage
Power consumption
Redundant power supply
Redundant Fan
Dimensions (W x D x H (mm) )
Weight
Environmental Conditions
OS Support *5
Attached tool (Standard)
1 port (100BASE-TX/10BASE-T)
AC 100-127V (50/60Hz) / AC 200-240V (50/60Hz) x 1 (max. 2)
645W / 2322kJ/h (max.)
optional (hot plug)
standard (hot plug)
445 (483 incl. protruding parts）(W) x 720 (792 incl. protruding parts）(D) x 88 (2U) (H)
30kg (32.5kg incl. rack rails) (max.)
Temperature10-35°C / Humidity 20-80% (non condensing)
Windows Server® 2008 Standard (32-bit) / Windows Server® 2008 Enterprise (32-bit)
Windows Server® 2008 Standard (64-bit) / Windows Server® 2008 Enterprise (64-bit)
Windows Server® 2003 R2, Standard Edition (SP2) / Windows Server® 2003 R2, Enterprise Edition (SP2)
Windows Server® 2003, Standard Edition (SP2) / Windows Server® 2003, Enterprise Edition (SP2)
Windows Server® 2003 R2, Standard x64 Edition (SP2) / Windows Server® 2003 R2, Enterprise x64 Edition (SP2)
Windows Server® 2003, Standard x64 Edition (SP2) / Windows Server® 2003, Enterprise x64 Edition (SP2)
Red Hat Enterprise Linux ES (v.4 for x86) *18 / Red Hat Enterprise Linux AS (v.4 for x86) *18
Red Hat Enterprise Linux 5 (for x86) *18 *19
Red Hat Enterprise Linux ES (v.4 for EM64T) *18 / Red Hat Enterprise Linux AS (v.4 for EM64T) *18
Red Hat Enterprise Linux 5 (for Intel64) *18 *19
ServerStart (Setup Support tool) *20
*1. Available memory capacity will be changed by the type of OS. Please find more details in Notes[Memory OS Compatibility List].
*2. Resolution is determined by functions of the display monitor and OS.
*3. HDD capacity is calculated according to the formulas 1GB=10003 byte and 1TB=10004 byte.
*4. All internal HDD must be configured as RAID structure.
*5. Drivers for Linux are not attached. Please download and use drivers of the following URL.
http://www.fujitsu.com/global/services/computing/server/ia/driver/
*6. CPU Conversion kit: Xeon E5205(1.86GHz) -> Xeon X5470(3.33GHz) (PGBFU42M) is available for upgrading to Intel® Xeon® X5470(3.33GHz).
*7. CPU Conversion kit: Xeon E5205(1.86GHz) -> Xeon X5460(3.16GHz) (PGBFU42L) is available for upgrading to Intel® Xeon® X5460(3.16GHz).
*8. CPU Conversion kit: Xeon E5205(1.86GHz) -> Xeon E5420(2.50GHz) (PGBFU42K) is available for upgrading to Intel® Xeon® E5420(2.50GHz).
*9. CPU Conversion kit: Xeon E5205(1.86GHz) -> Xeon E5405(2GHz) (PGBFU42J) is available for upgrading to Intel® Xeon® E5405(2GHz).
*10. CPU Conversion kit: Xeon E5205(1.86GHz) -> Xeon X5270(3.50GHz) (PGBFU42N) is available for upgrading to Intel® Xeon® X5270(3.50GHz).
*11. CPU Conversion kit: Xeon E5205(1.86GHz) -> Xeon X5260(3.33GHz) (PGBFU42H) is available for upgrading to Intel® Xeon® X5260(3.33GHz).
*12. TPM is available for BitLockerTM Drive Encryption of Windows Server® 2008.
*13. This is the maximum memory capacity when Memory Expansion Board (PG-RB108) is applied.
*14. When Serial Port (PG-COM03) is applied, PCI Express slot x 1 is occupied.
*15. When Parallel Port Option (PG-PP05) is applied, PCI Express slot x 1 is occupied.
*16. Only 6 ports are available.
*17. One USB-FDD is required as a minimum in multiple servers.
It is necessary to procure USB-FDD separately.
*18. Regarding supported kernel versions of Linux, please refer to the following list.
http://www.fujitsu.com/downloads/PRMRGY/linux-os-kernel-compatibility-list.pdf
*19. Total number of cores of CPU(s) should be four or more for using VM (Virtual Machine) function.
*20. ServerStart doesn't support Linux.
*. Noise level is 52dB.
PRIMERGY RX300 S4
Configuration Diagram
DIMM Slot 3D
DIMM Slot 3C
DIMM Slot 2D
DIMM Slot 2C
DIMM Slot 1D
DIMM Slot 1C
Power Supply Unit
Memory Expansion
Board 2
( Optional )
DIMM Slot 3B
DIMM Slot 3A
DIMM Slot 2B
DIMM Slot 2A
DIMM Slot 1B
DIMM Slot 1A
PCI7 PCI Express (x4)
PCI6 PCI Express (x4)
PCI5 PCI Express (x4)
PCI4 PCI-X 64bit / 133MHz
PCI3 PCI Express (x4)
PCI2 PCI Express (x4)
PCI1 PCI Express (x4)
Memory Expansion
Board 1
( Standard )
Power Supply Unit
PCI Slots
Hard Disk 3.5inch Bay (hot plug)
Standard Drive Cage ( HDD only )
( HDD x 6ports )
Bay 1
SAS
Bay 2
SAS
Bay 3
SAS
CPU
Xeon® X5470 /
X5460 / E5420 /
E5405 /
X5270 / X5260 /
E5205
Xeon® X5470 /
X5460 / E5420 /
E5405 /
X5270 / X5260 /
E5205
Bay 4
SAS
Bay 5
SAS
3.5 inch HDD Bay 3
(hot plug) *1
3.5 inch HDD Bay 6
(hot plug)
3.5 inch HDD Bay 2
(hot plug) *1
3.5 inch HDD Bay 5
(hot plug)
3.5 inch HDD Bay 1
(hot plug)
DVD-ROM Drive
*1.If Tape Drv DAT72 36GB internal w/ Drive Cage (PG-DT504D) is installed,
HDD cannot be installed for the position of 3.5inch Bay 2 and 3.
Bay 6
SAS
3.5 inch HDD Bay 4
(hot plug)
Hard Disk 3.5inch Bay (hot plug)
Standard Drive Cage ( HDD and Backup Device )
( HDD x 4ports + Backup Device )
*Components installed as standard configuration marked in grey.
Bay 1
SAS
Bay 4
SAS
Bay 5
SAS
Bay 6
SAS
Backup Device
( DAT72 )
PRIMERGY RX300 S4
Mountable I/O Options
1
Mount
Priority
Mountable Cards
Bus
2
PCI Express
x4
lane
3
x8
socket
High
Low
PCI Slot
4
PCI-X
64bit/
133MHz
LowProfile
5
6
PCI Express
x4
lane
7
Max No.
of Mount
Remarks
x8
socket
3.3V
SAS RAID Ctrl
( 8ports / 256MB / without BBU )
PCI Express (x4)
#
-
-
-
-
-
-
1
Standard, Internal array
SAS RAID Ctrl
( 8ports / 512MB / with BBU )
PG-248CL
PCI Express (x4)
[1]
-
-
-
-
-
-
1
Internal array
Serial Port
PG-COM03
-
-
-
-
-
-
-
[1]
1
Parallel Port Option
PG-PP05
-
-
-
-
-
-
[2]
[1]
1
SAS RAID Ctrl
( 8ports / 512MB / with BBU )
PG-248G2L PCI Express (x4)
-
[1]
-
-
-
-
-
1
External array
SAS Ctrl
( 4ports )
PG-228BL
PCI Express (x4)
-
[3]
[1]
-
[4]
[2]
-
3
External SAS Controller
SCSI Ctrl U320 lp
PG-2281L
PCI Express (x4)
-
[1]
[2]
-
[3]
[4]
-
1
External SCSI Controller
Fibre Channel Controller
(4Gbps)
PG-FC202
PCI Express (x4)
-
[4]
[3]
-
[2]
[1]
-
2
(*1)
Fibre Channel Controller lp
(8Gbps)
PG-FC203L PCI Express (x8)
-
[4]
[3]
-
[2]
[1]
-
4
(*1)
Eth. Ctrl 1000-BASE-SX Fibre
LC lp
PG-1882L
PCI-X/64bit
-
-
-
[1]
-
-
-
1
Eth. Ctrl 1000-BASE-T Cu lp
PG-1892L
PCI-X/64bit
-
-
-
[1]
-
-
-
1
Eth. Ctrl 1x1Gbit PCI
1000-BASE-T lp
PG-1853L
PCI/32bit
-
-
-
[1]
-
-
-
1
Eth. Ctrl 2x1Gbit PCI-X
1000-BASE-T lp
PG-1863L
PCI-X/64bit
-
-
-
[1]
-
-
-
1
Eth. Ctrl 1x1Gbit PCI-E
1000-BASE-T lp
PG-289L
PCI Express (x1)
-
[5]
[4]
-
[3]
[2]
[1]
4
Eth. Ctrl 1x1Gbit PCI-E
1000BASE-SX lp
PG-288L
PCI Express (x4)
-
[5]
[4]
-
[3]
[2]
[1]
4
Eth. Ctrl 2x1Gbit PCI-E
1000-BASE-T lp
PG-2861L
PCI Express (x4)
-
[5]
[4]
-
[3]
[2]
[1]
4
Eth. Ctrl 1x1Gbit PCI-E
1000-BASE-T lp
PG-285L
PCI Express (x1)
-
[5]
[4]
-
[3]
[2]
[1]
4
* [n] : Installation Priority
* # : standard
* - : cannot be installed
(*1) Fibre Channel Controller(PG-FC202) and Fibre Channel Controller lp (PG-FC203L) cannot be installed at a time.
7
No AFT/ALB Support
No AFT/ALB Support
PRIMERGY RX300 S4
Connection Table
CPU
Processor Xeon X5470(3.33GHz)
Max: 2 CPU
PG-FG42M
CPU Slot
PGBFG42M (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon E5205(1.86GHz) -> Xeon X5470(3.33GHz) (PGBFU42M) is applied.
Processor Xeon X5460(3.16GHz)
PG-FG42L
PGBFG42L (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon E5205(1.86GHz) -> Xeon X5460(3.16GHz) (PGBFU42L) is applied.
Processor Xeon E5420(2.50GHz)
PG-FG42K
PGBFG42K (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon E5205(1.86GHz) -> Xeon E5420(2.50GHz) (PGBFU42K) is applied.
Processor Xeon E5405(2GHz)
PG-FG42J
PGBFG42J (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon E5205(1.86GHz) -> Xeon E5405(2GHz) (PGBFU42J) is applied.
Processor Xeon X5270(3.50GHz)
PG-FG42N
PGBFG42N (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon E5205(1.86GHz) -> Xeon X5270(3.50GHz) (PGBFU42N) is applied.
Processor Xeon X5260(3.33GHz)
PG-FG42H
PGBFG42H (for CTO)
*. This option is available when CPU Conversion Kit:
Xeon E5205(1.86GHz) -> Xeon X5260(3.33GHz) (PGBFU42H) is applied.
Processor Xeon E5205(1.86GHz)
PG-FG42G
PGBFG42G (for CTO)
*. This option is available when the processor of the base unit
is Processor Xeon E5205(1.86GHz).
*CPU Conversion kit (available only as a Configure To Order (CTO) option; no separate shipment is possible)
Type
Xeon E5205(1.86GHz)
Remarks
Product ID
CPU Conversion kit:
Intel® Xeon® E5205(1.86GHz/6MB) -> Intel® Xeon® X5470(3.33GHz/12MB)
PGBFU42M
-> Xeon X5470(3.33GHz)
Convert the CPU installed as standard in the base unit to the other.
(Note: This option can be ordered only as coupled with the base unit.
(for CTO)
A separate shipment is not possible.)
CPU Conversion kit:
Intel® Xeon® E5205(1.86GHz/6MB) -> Intel® Xeon® X5460(3.16GHz/12MB)
Xeon E5205(1.86GHz)
PGBFU42L
-> Xeon X5460(3.16GHz)
Convert the CPU installed as standard in the base unit to the other.
(Note: This option can be ordered only as coupled with the base unit.
(for CTO)
A separate shipment is not possible.)
CPU Conversion kit:
Intel® Xeon® E5205(1.86GHz/6MB) -> Intel® Xeon® E5420(2.50GHz/12MB)
Xeon E5205(1.86GHz)
PGBFU42K
-> Xeon E5420(2.50GHz)
Convert the CPU installed as standard in the base unit to the other.
(Note: This option can be ordered only as coupled with the base unit.
(for CTO)
A separate shipment is not possible.)
CPU Conversion kit:
Intel® Xeon® E5205(1.86GHz/6MB) -> Intel® Xeon® E5405(2GHz/12MB)
Xeon E5205(1.86GHz)
PGBFU42J
-> Xeon E5405(2GHz)
Convert the CPU installed as standard in the base unit to the other.
(Note: This option can be ordered only as coupled with the base unit.
(for CTO)
A separate shipment is not possible.)
CPU Conversion kit:
Intel® Xeon® E5205(1.86GHz/6MB) -> Intel® Xeon® X5270(3.50GHz/6MB)
Xeon E5205(1.86GHz)
PGBFU42N
-> Xeon X5270(3.50GHz)
Convert the CPU installed as standard in the base unit to the other.
(Note: This option can be ordered only as coupled with the base unit.
(for CTO)
A separate shipment is not possible.)
CPU Conversion kit:
Intel® Xeon® E5205(1.86GHz/6MB) -> Intel® Xeon® X5260(3.33GHz/6MB)
Xeon E5205(1.86GHz)
PGBFU42H
Convert the CPU installed as standard in the base unit to the other.
-> Xeon X5260(3.33GHz)
(Note: This option can be ordered only as coupled with the base unit.
(for CTO)
A separate shipment is not possible.)
PRIMERGY RX300 S4
Memory (PC2 5300F)
Max: 48GB (4GB FB-DIMM x 12)
(Standard)
Memory Module-1GB (512MB FB-DIMM x 2, PC2 5300F)
Memory
Expansion
Board Slot
PG-RM1CG
Standard Memory Module:
PGBRM1CG (for CTO)
1GB (512MB FB-DIMM x 2)
2 slot / Max: 2
Memory Expansion Board
Memory Module-2GB (1GB FB-DIMM x 2, PC2 5300F)
( DIMM slot x 6 )
PG-RM2CG
PG-RB108
PGBRM2CG (for CTO)
Memory Module-4GB (2GB FB-DIMM x 2, PC2 5300F)
PG-RM4CG
PGBRM4CG (for CTO)
Memory Module-8GB (4GB FB-DIMM x 2, PC2 5300F)
PG-RM8CG
PGBRM8CG (for CTO)
Memory Module Conversion kit-2GB (1GB FB-DIMM x 2, PC2 5300F)
PGBRU2CG (for CTO)
Memory Module Conversion kit-4GB (2GB FB-DIMM x 2, PC2 5300F)
PGBRU4CG (for CTO)
Memory Module Conversion kit-8GB (4GB FB-DIMM x 2, PC2 5300F)
(Optional)
PGBRU8CG (for CTO)
Memory Module-1GB (512MB FB-DIMM x 2, PC2 5300F)
PG-RM1CG
Memory Expansion Board
Memory Module-2GB (1GB FB-DIMM x 2, PC2 5300F)
( DIMM slot x 6 )
PG-RM2CG
PG-RB108
Memory Module-4GB (2GB FB-DIMM x 2, PC2 5300F)
PG-RM4CG
Memory Module-8GB (4GB FB-DIMM x 2, PC2 5300F)
PG-RM8CG
* Notes on installing memory
1. Memory is installed by pairs of FB-DIMMs of the same capacity. Installation of one FB-DIMM or a mixed -capacity pair is impossible.
2. The memory capacities of the slots should be in ascending order in the following sequence:
(1) In case of 1 x Memory Expansion Board
DIMM slots 1A,1B (Bank 1) -> DIMM slots 2A,2B (Bank 2) -> DIMM slots 3A,3B (Bank 3)
The following patterns of memory installation are available.
Memory Expansion Board 1
Bank1
Bank2
Bank3
1A
1B
2A
2B
3A
0
0
-
-
-
-
0
0
0
0
-
-
0
0
0
0
0
0
0 : Memory is installed.
3B
- : Memory is not installed.
(2) In case of 2 x Memory Expansion Board
DIMM slots 1A,1B (Bank 1) -> DIMM slots 1C,1D (Bank 5) -> DIMM slots 2A,2B (Bank 2) -> DIMM slots 2C,2D (Bank 6) ->
DIMM slots 3A,3B (Bank 3) -> DIMM slots 3C,3D (Bank 7)
The following patterns of memory installation are available.
Memory Expansion Board 1
Bank1
Memory Expansion Board 2
Bank2
Bank3
Bank5
Bank6
Bank7
1A
1B
2A
2B
3A
3B
1C
1D
2C
2D
3C
0
0
-
-
-
-
-
-
-
-
-
3D
-
0
0
-
-
-
-
0
0
-
-
-
-
0
0
0
0
-
-
0
0
-
-
-
-
0
0
0
0
-
-
0
0
0
0
-
-
0
0
0
0
0
0
0
0
0
0
-
-
0
0
0
0
0
0
0
0
0
0
0
0
0 : Memory is installed.
- : Memory is not installed.
PRIMERGY RX300 S4
3. Memory Mirroring Function
In case of using Memory Mirroring function, the following conditions are required.
(1) FB-DIMM x 4, FB-DIMM x 8 or FB-DIMM x 12 should be installed.
(2) Memory capacity of each Bank should be same.
(3) Available memory capacity is half of installed memory.
The following patterns of memory installation are available for Memory Mirroring function.
Memory Expansion Board 1
Bank1
Memory Expansion Board 2
Bank2
Bank3
Bank5
Bank6
Bank7
1A
1B
2A
2B
3A
3B
1C
1D
2C
2D
3C
3D
0
0
-
-
-
-
0
0
-
-
-
-
0
0
0
0
-
-
0
0
0
0
-
-
0
0
0
0
0
0
0
0
0
0
0
0
0 : Memory is installed.
- : Memory is not installed.
4. Spare Memory Function
In case of using Spare Memory function, the following conditions are required.
(1) Memory capacity of each memory of Memory Expansion Board should be same.
(2) Available memory capacity is two thirds of installed memory.
The following patterns of memory installation are available for Spare Memory function.
(a) In case of 1 x Memory Expansion Board
Memory Expansion Board 1
Bank1
Bank2
Bank3
1A
1B
2A
2B
3A
3B
0
0
0
0
0
0
0 : Memory is installed.
- : Memory is not installed.
(b) In case of 2 x Memory Expansion Board
Memory Expansion Board 1
Bank1
Memory Expansion Board 2
Bank2
Bank3
Bank5
Bank6
Bank7
1A
1B
2A
2B
3A
3B
1C
1D
2C
2D
3C
3D
0
0
0
0
0
0
0
0
0
0
0
0
0 : Memory is installed.
- : Memory is not installed.
5. Available memory capacity depends on the type of OS and some memory area is used for PCI resource management.
The following table shows installed memory capacity and available memory capacity.
OS
Windows Server® 2008 Standard (32-bit)
Windows Server® 2003 R2, Standard Edition (SP2)
Windows Server® 2003, Standard Edition (SP2)
Installed Memory
Capacity
~3.0GB
3.0GB~4.0GB
Available Memory Capacity
Same as installed memory capacity
3.0GB *1
Red Hat Enterprise Linux ES (v.4 for x86)
Red Hat Enterprise Linux AS (v.4 for x86)
Red Hat Enterprise Linux 5 (for x86)
~12.0GB
Same as installed memory capacity
Red Hat Enterprise Linux ES (v.4 for EM64T)
~16.0GB
Same as installed memory capacity
Windows Server® 2008 Standard (64-bit)
Windows Server® 2003 R2, Standard x64 Edition (SP2)
Windows Server® 2003, Standard x64 Edition (SP2)
~32.0GB
Same as installed memory capacity
~3.0GB
Same as installed memory capacity
Windows Server® 2008 Enterprise (32-bit)
Windows Server® 2003 R2, Enterprise Edition (SP2)
Windows Server® 2003, Enterprise Edition (SP2)
Windows Server® 2008 Enterprise (64-bit)
Windows Server® 2003 R2, Enterprise x64 Edition (SP2)
Windows Server® 2003, Enterprise x64 Edition (SP2)
Red Hat Enterprise Linux AS (v.4 for EM64T)
Red Hat Enterprise Linux 5 (for Intel64)
3.0GB~48.0GB
~48.0GB
3.0GB *1
Same as installed memory capacity
*1. If installed memory capacity is more than 3.0GB, it is necessary to set "PAE (Physical Address Extension)" of OS.
The following (1) and (2) are the ways to set "PAE" of OS, and Fujitsu recommends (1).
(1) Set "PAE" of OS.
Regarding setting "PAE" of OS, please refer to website of Microsoft.
(2) Set "DPE (Data Execution Prevention)" of CPU.
If "DPE" of CPU is set as "available" by executing the following procedure, "PAE" of OS is set automatically.
[1] Execute "BIOS setup utility".
[2] Select "Advanced" menu.
[3] Select "Advanced Processor" submenu.
[4] Set "NX Memory Protection" as "Enabled".
PRIMERGY RX300 S4
Connecting Internal HDD and Internal Backup Devices
If you would like to order internal HDD and internal backup devices, please order optional cards/cables according to the following table.
Type of HDD connection
Connection
PRIMERGY RX300 S4 Internal Backup Devices
USB (''1) Connection
Interface
(not connect)
SAS RAID Ctrl
RAID
PRIMERGY SX10 S2 Internal Backup Devices
SCSI Wide (''2) Backup Devices Connection
SCSI Card (PG-2281L / PGB2281L)
SCSI Cable (PG-CBLS034 / PGBCBLS035)
When Internal backup device
is installed.
(2 HDD bays are occupied.)
Onboard USB
(internal port)
SAS RAID Ctrl
(''1) USB Backup Devices: PG-DT504D
(''2) SCSI Wide Backup Devices: PG-DT501/PG-LT302 /PG-LT201/PG-LT102
Internal HDD
RAID Configuration
Max: 6 HDDs
PCI Express
HDD SAS 15k 73GB hot plug 3.5inch
Bus
PG-HDB75A
SAS RAID Ctrl
( installed as standard )
PGBHDB75A (for CTO)
( 8ports / 256MB / without BBU )
HDD SAS 15k 147GB hot plug 3.5inch
*. RAID 0/1/1+0/5/6 configuration can be set.
PG-HDB45A
PGBHDB45A (for CTO)
SAS RAID Ctrl
( 8ports / 512MB / with BBU )
HDD SAS 15k 300GB hot plug 3.5inch
PG-248CL
PG-HDB35A
PGBHDB35A (for CTO)
*. RAID 0/1/1+0/5/6 configuration can be set.
SAS RAID Ctrl Conversion kit
HDD SAS 15k 450GB hot plug 3.5inch
( 8ports / 256MB / without BBU -> 8ports / 512MB / with BBU )
PG-HDB55A
PGB2U48CL
PGBHDB55A (for CTO)
*. RAID 0/1/1+0/5/6 configuration can be set.
*. SAS RAID Ctrl includes a battery as standard equipment.
The battery lifetime is 3 years.
Please purchase the following spare battery and replace the old battery with new one
before the battery runs out.
Battery Backup Unit
PG-BBU1
Internal backup device (USB)
Tape Drv DAT72 36GB internal w/ Drive Cage
USB Interface
PG-DT504D
(internal)
PGBDT504D (for CTO)
*. One internal backup device can be mounted.
Notes regarding Max number of HDD
If Internal Backup Device is installed, Max number of HDD is changed from 6 to 4.
Internal Backup Device
Max number of HDD
not installed
6
Tape Drv DAT72 36GB internal w/ Drive Cage
( PG-DT504D / PGBDT504D )
4
( HDD cannot be installed for the position
of 3.5inch Bay 2 and 3. )
External DVD-RAM
USB Interface
DVD-RAM
USB Extension Cable
PG-CBLU002
PRIMERGY RX300 S4
Hard Disk Cabinet (PRIMERGY SX35)
PCI Express
Bus
SAS RAID Ctrl
SAS Cable
PRIMERGY SX35
( 8ports / 512MB / with BBU )
PG-CBLA005
(12bays)
PG-248G2L
PG-R2DC2
PGB248G2L (for CTO)
*. RAID 0/1/1+0/5/6 configuration can be set.
*. SAS RAID Ctrl includes a battery as standard equipment.
The battery lifetime is 3 years.
Please purchase the following spare battery and replace the old battery with new one
before the battery runs out.
Battery Backup Unit
PG-BBU4
*. Please find more details in Rackmount [Hard Disk Cabinet (PRIMERGY SX35)].
Backup Device Cabinet (PRIMERGY SX10 S2)
PCI Express
Bus
SCSI Ctrl U320 lp
SCSI Cable
I/O Module
PRIMERGY SX10 S2
PG-2281L
PG-CBLS034
PGBIMS01 (for CTO)
(4bays)
PGB2281L (for CTO)
SCSI Cable
PG-R2BC1
PG-CBLS035
*. Please find more details in Rackmount [Backup Device Cabinet (PRIMERGY SX10 S2)].
Power Supply Units
Max: 2 Units
Power Supply Module
Standard: 1 Unit
PGBPU125 (for CTO)
Power Supply Slot
PG-PU125
LAN Card
On-board LAN
Eth. Ctrl 2x1Gbit PCI-E 1000-BASE-T lp
PCI Express
PG-2861L
Bus
PGB2861L (for CTO)
Twist Pair Cable ( Category 5e)
* Dual Port
Eth. Ctrl 1x1Gbit PCI-E 1000-BASE-T lp
PG-289L
PGB289L (for CTO)
Eth. Ctrl 1x1Gbit PCI-E 1000-BASE-T lp
PG-285L
PGB285L (for CTO)
* No AFT/ALB Support
*. Supported versions of Linux are 5.2 or later and 4.7 or later.
Eth. Ctrl 1x1Gbit PCI-E 1000BASE-SX lp
PG-288L
Multi Mode Fibre Channel Cable
Eth. Ctrl 2x1Gbit PCI-X 1000-BASE-T lp
PCI Bus
PG-1863L
Twist Pair Cable ( Category 5e)
* Dual Port
Eth. Ctrl 1000-BASE-T Cu lp
PG-1892L
PGB1892L (for CTO)
Eth. Ctrl 1x1Gbit PCI 1000-BASE-T lp
PG-1853L
PGB1853L (for CTO)
* No AFT/ALB Support
Eth. Ctrl 1000-BASE-SX Fibre LC lp
PG-1882L
Multi Mode Fibre Channel Cable
PRIMERGY RX300 S4
Server Management (Remote Management Controller)
LAN interface for Remote
Twist Pair Cable ( Category 5e)
Management Controller
Remote Management Ctrl Upgrade kit
PG-RMCU2
Serial Port
Serial Port
PCI Slot
PG-COM03
*. This option occupies one PCI slot.
Parallel Port Option
Parallel Port Option
PCI Slot
PG-PP05
*. This option occupies one PCI slot.
Specifications are subject to change without notice. For the latest detailed information, contact your local representative.
All brand names and product names are trademarks and registered trademarks of their respective holders.
©2008 Fujitsu Limited. All rights reserved. Printed in Japan.