Device Comment Data Name : COMMENT 12/11/2021 Device Name Comment M0 MASTER ON M1 EMERGENCY M2 HOME POS M3 MARKING READY M4 MARK BUSY M5 MARK COMPLETE M6 MARK END MARKKING M7 MARK ERROR M8 TCM DON M9 TCM READY M10 PART 1 DETECT M11 PART 2 DETECT M12 PART READY M13 AUTO READY M14 HOMING M15 FEED BWD HOMING M16 MARKING FEED LEFT HOMING M100 REQ FEED FWD M101 REQ FEED BWD M102 REQ FEED LEFT M103 REQ FEED RIGHT M104 REQ CHECK LAMP M150 AUTO ON M151 FEED FWD 1ST M152 MARKING ON 1ST M153 FEED BWD 1ST M154 FEED RIGHT M155 FEED FWD 2ND M156 MARKING ON 2ND M157 FEED BWD 2ND M158 FEED LEFT HOME M199 FINISH AUTO M300 FEED FWD M301 FEED BWD M302 FEED LEFT M303 FEED RIGHT M500 MANUAL MODE M501 AUTO MODE M502 VECTOR M503 TELESIS M700 SEND DATA COMPLETE M701 RESULTPROCESS M702 PRINT HEAD DOWN(TP.PL) M704 WORK CLAMP UP(TP.PL) M706 WORK CLAMP DOWN(TP.PL) M708 NUM. START(TP.PL) M710 NUM. STOP(TP.PL) M730 DCM NO USE(TP.PL) M732 DCM USE(TP.PL) M800 CLEAR STOCK 1 M801 CLEAR STOCK 2 M802 CLEAR STOCK 3 1 Device Comment Data Name : COMMENT Device Name M803 CLEAR STOCK 4 M804 CLEAR STOCK 5 M805 CLEAR STOCK 6 M806 CLEAR STOCK 7 M807 CLEAR STOCK 8 M808 CLEAR STOCK 9 M809 CLEAR STOCK 10 M3003 RESET M3300 DONT TRIGGER IF DATA NOL M7000 trial SM0 Diagnostic errors SM1 Self-diagnosis error SM5 Error common information SM16 Error individual information SM50 Error reset SM51 Battery low latch SM52 Battery low SM53 AC/DC DOWN detection SM56 Operation Errors SM60 Blown fuse detection SM61 I/O module verification error SM62 Annunciator detection SM100 Serial communication using flag SM101 Comm. protocol status flag SM110 Protocol error SM111 Communication status SM112 Error information clear SM113 Overrun error SM114 Parity error SM115 Framing error SM165 Prog memory batch transfer sts SM202 LED OFF command SM203 STOP contact SM204 PAUSE contact SM206 PAUSE enable coil SM210 Clock data set request SM211 Clock data error SM213 Clock data read request SM220 No.1 CPU ready completion flag SM221 No.2 CPU ready completion flag SM222 No.3 CPU ready completion flag SM237 Device range check disable flag SM240 No. 1 CPU reset flag SM241 No. 2 CPU reset flag SM242 No. 3 CPU reset flag SM244 No. 1 CPU error flag SM245 No. 2 CPU error flag SM246 No. 3 CPU error flag SM254 All stations refresh command SM320 Presence/absence of SFC program SM321 Start/stop SFC program SM322 SFC program start status 12/11/2021 Comment 2 Device Comment Data Name : COMMENT Device Name SM323 Presence of continue transition SM324 Continuous transition stop flag SM325 Output mode at block stop SM326 SFC device clear mode SM327 Output during end step execution SM328 End step get clear process mode SM391 GINIT execution completion flag SM400 Always ON SM401 Always OFF SM402 After RUN, ON for 1 scan only SM403 After RUN, OFF for 1 scan only SM409 0.01 second clock SM410 0.1 second clock SM411 0.2 second clock SM412 1 second clock SM413 2 second clock SM414 2n second clock SM415 2n (ms) clock SM420 User timing clock No.0 SM421 User timing clock No.1 SM422 User timing clock No.2 SM423 User timing clock No.3 SM424 User timing clock No.4 SM620 Drive 3/4 usable flags SM621 Drive 3/4 protect flag SM622 Drive 3 flag SM623 Drive 4 flag SM624 Memory card B in-use flag SM640 File register use SM650 Comment use SM671 Backup latch data complete flag SM675 Backup latch data err complete SM676 Repetition execution of restore SM680 Program memory writing error SM681 Program memory in-write flag SM682 Prog memory rewrite cnt err flag SM685 Standard ROM writing error SM686 Standard ROM in-write flag SM687 Standard ROM rewrite count error SM700 Carry flag SM701 Output characters switch SM702 Search method SM703 Sort order SM704 Block comparison SM709 DT,TM illegal detection flag SM715 EI flag SM716 Block comparison SM717 Block comparison (interrupt prg) SM718 Block comparison (I45) SM720 Comment read completion flag SM721 File being accessed SM722 BIN/DBIN inst. err. disable flag 12/11/2021 Comment 3 Device Comment Data Name : COMMENT Device Name SM741 Data sort completion flag SM750 Scaling data check setting SM774 PID bumpless(differential) SM775 COM inst. exec. refresh select SM776 Enable/disable of dev. in CALL SM777 Enable/disable of interrupt dev. SM794 PID bumpless(Not differential) SM800 Trace preparation SM801 Trace start SM802 Trace execution in progress SM803 Trace trigger SM804 After trace trigger SM805 Trace completed SM826 Trace error SM829 Trace setting compulsion regist SM1000 Fuse blown SM1002 I/O module verification error SM1005 AC DOWN detection SM1006 Battery low SM1007 Battery low latch SM1008 Self-diagnosis error SM1009 Annunciator detection SM1020 User timing clock No.0 SM1021 User timing clock No.1 SM1022 User timing clock No.2 SM1023 User timing clock No.3 SM1024 User timing clock No.4 SM1025 Clock data set request SM1026 Clock data error SM1028 Clock data read request SM1030 0.1 second clock SM1031 0.2 second clock SM1032 1 second clock SM1033 2 second clock SM1034 2n second clock(1minute clock) SM1036 Always ON SM1037 Always OFF SM1038 ON for 1 scan only after RUN SM1039 RUN flag(1 scan only OFF) SM1041 PAUSE status contact SM1042 STOP status contact SM1043 Sampling trace completed SM1046 Sampling trace SM1780 Power supply off detection flag SM1781 Power supply failure detect flag SM1782 Power supply1 stop detect flag SM1783 Power supply2 stop detect flag X0E QJ71C24N ERROR X40 EMERGENCY\ X41 MASTER ON X42 SS AUTO/MAN X43 SS VECT/TELE 12/11/2021 Comment 4 Device Comment Data Name : COMMENT 12/11/2021 Device Name Comment X44 PB HOME X45 PB RESET X46 PB AUTO START 1 X47 PB AUTO START 2 X48 PH PART DETECT 1 X49 PH PART DETECT 2 X4F AIR PRESSURE ON X50 RS FEEDER FWD X51 RS FEEDER BWD X52 RS FEEDER LEFT X53 RS FEEDER RIGHT3 X56 MARK READY X57 MARK BUSY X58 MARK COMPLETE X59 MARK END MARKING X5A MARK ERROR X5C MRKG TCM DONE X5D MRKG TCM READY X68 SHOT NO X6C SHOT NO X70 SHOT NG SIGNAL DCM X75 START FROM ROBOT Y0E QJ71C24N RESET Y61 ALARM BUZZER Y62 PBL MASTER ON Y63 STL MAN OP Y64 STL ALARM Y65 STL AUTO OP Y66 SV FEED FWD Y67 SV FEED BWD Y68 SV FEED LEFT Y69 SV FEED RIGHT Y6A CR CHECK LAMP Y70 MARK RESET Y71 MARK HOME RETURN Y72 MARK NUMBER START Y73 MARK DATA 0 Y74 MARK DATA 1 Y78 MARKG TCM START Y79 MARKG TCM ABORT B1 HMI- SOL UPDOWN B2 HMI-CLAMP B3 HMI-INJECT B4 HMI-MARKING START B10 HMI_CLEAR DATA B11 HMI_CLEAR DATA B12 HMI_RESET COUNTER B19 HMI_TOSOK MEASURE B20 HMI_TOSOK SETTING UP B21 HMI_TOSOK SETTING DOWN B100 HMI_LINE A B101 HMI_LINE B 5 Device Comment Data Name : COMMENT Device Name B102 HMI_LINE C B103 HMI_LINE D B104 HMI_LINE E B105 HMI_LINE F B210 HMI_ONLINE/OFFLINE D3 DATA NG DCM D4 DATA SHIFT LOCK D5 DATA GROUP LOCK D30 HMI_COUNTER SETTING D70 DATA MARKING INPUT MANUAL D84 TYPE PITCH DATA D138 GROUP D139 SHIFT D200 TANGGAL D201 BULAN D205 DATA SHOT NO D207 DATA SHOT NO D212 DATA DCM D250 DATA TANGGAL D260 DATA BULAN D400 PORT QJ71C24N D450 DATA READ TOSOK D500 MC LINE D600 SATUAN D620 PULUHAN D640 RATUSAN D660 RIBUAN D700 SATUAN D720 PULUHAN D740 RATUSAN D760 RIBUAN D900 DATA TO PRINT D2013 DATA MEMORY JAM D2014 DATA MEMORY MINUTE D5100 DCM STOCK1 D5105 DCM STOCK 2 D5110 DCM STOCK 3 D5115 DCM STOCK 4 D5120 DCM STOCK 5 D5125 DCM STOCK 6 D5130 DCM STOCK 7 D5135 DCM STOCK 8 D5140 DCM STOCK 9 D5145 DCM STOCK 10 D5150 FIRST ENTRY DATA D5200 DATA DISPLAY TO HMI D6150 COUNTER SHOT NO D7050 DATA FROM MANUAL SD0 Diagnostic errors SD1 Diagnosis error occurrence time SD2 Diagnosis error occurrence time SD3 Diagnosis error occurrence time 12/11/2021 Comment 6 Device Comment Data Name : COMMENT 12/11/2021 Device Name Comment SD4 Error information categories SD5 Error common information SD6 Error common information SD7 Error common information SD8 Error common information SD9 Error common information SD10 Error common information SD11 Error common information SD12 Error common information SD13 Error common information SD14 Error common information SD15 Error common information SD16 Error Individual information SD17 Error Individual information SD18 Error Individual information SD19 Error Individual information SD20 Error Individual information SD21 Error Individual information SD22 Error Individual information SD23 Error Individual information SD24 Error Individual information SD25 Error Individual information SD26 Error Individual information SD50 Error reset SD51 Battery low latch SD52 Battery low SD53 AC/DC DOWN detection SD60 Number of module with blown fuse SD61 I/O module verify error No. SD62 Annunciator number SD63 Number of annunciators SD64 Annunciator detect number table SD65 Annunciator detect number table SD66 Annunciator detect number table SD67 Annunciator detect number table SD68 Annunciator detect number table SD69 Annunciator detect number table SD70 Annunciator detect number table SD71 Annunciator detect number table SD72 Annunciator detect number table SD73 Annunciator detect number table SD74 Annunciator detect number table SD75 Annunciator detect number table SD76 Annunciator detect number table SD77 Annunciator detect number table SD78 Annunciator detect number table SD79 Annunciator detect number table SD100 Transmission speed storage area SD101 Communication set storage area SD102 Trans. wait time storage area SD105 CH1 transmission speed(RS-232) SD110 Data sending result storage area 7 Device Comment Data Name : COMMENT Device Name SD111 Data receive result storage area SD118 Amount of battery consumption SD119 Battery long-lived factor SD200 Status of switch SD201 LED status SD202 LED off command SD203 Operating status of CPU SD204 LED display color SD207 LED display priority ranking SD208 LED display priority ranking SD209 LED display priority ranking SD210 Clock data SD211 Clock data SD212 Clock data SD213 Clock data SD220 LED display data SD221 LED display data SD222 LED display data SD223 LED display data SD224 LED display data SD225 LED display data SD226 LED display data SD227 LED display data SD240 Base mode SD241 No. of extension bases SD242 A/Q base differentiation SD243 No. of base slots SD244 No. of base slots SD250 Loaded maximum I/O SD254 MELSECNET/10.MELSECNET/H info. SD255 MELSECNET/10.MELSECNET/H info. SD256 MELSECNET/10.MELSECNET/H info. SD257 MELSECNET/10.MELSECNET/H info. SD258 MELSECNET/10.MELSECNET/H info. SD286 Device assign(Extended M) SD287 Device assign(Extended M) SD288 Device assign(Extended B) SD289 Device assign(Extended B) SD290 Device assign(Same parameter) SD291 Device assign(Same parameter) SD292 Device assign(Same parameter) SD293 Device assign(Same parameter) SD294 Device assign(Same parameter) SD295 Device assign(Same parameter) SD296 Device assign(Same parameter) SD297 Device assign(Same parameter) SD298 Device assign(Same parameter) SD299 Device assign(Same parameter) SD300 Device assign(Same parameter) SD301 Device assign(Same parameter) SD302 Device assign(Same parameter) SD303 Device assign(Same parameter) 12/11/2021 Comment 8 Device Comment Data Name : COMMENT Device Name SD304 Device assign(Same parameter) SD305 Device allocation (Z) SD306 Device assign1(Same parameter) SD307 Device assign1(Same parameter) SD308 Device assign2(Ext. device set) SD309 Device assign2(Ext. device set) SD310 Device assign2(Ext. device set) SD311 Device assign2(Ext. device set) SD340 Ethernet information SD341 Ethernet information SD342 Ethernet information SD343 Ethernet information SD344 Ethernet information SD345 Ethernet information SD346 Ethernet information SD347 Ethernet information SD393 Multiple CPU system information SD395 Multiple CPU system information SD396 Multiple CPU system information SD397 Multiple CPU system information SD398 Multiple CPU system information SD412 1 second counter SD414 2n second clock setting SD415 2nms clock setting SD420 Scan counter SD500 Execution program No. SD520 Current scan time SD521 Current scan time SD522 Initial scan time SD523 Initial scan time SD524 Minimum scan time SD525 Minimum scan time SD526 Maximum scan time SD527 Maximum scan time SD540 END processing time SD541 END processing time SD542 Constant scan wait time SD543 Constant scan wait time SD548 Scan exec program exec time SD549 Scan exec program exec time SD600 Memory card models SD620 Drive 3/4 models SD622 Drive 3 (RAM) capacity SD623 Drive 4 (ROM) capacity SD624 Drive 3/4 use conditions SD640 File register drive SD641 File register file name SD642 File register file name SD643 File register file name SD644 File register file name SD645 File register file name SD646 File register file name 12/11/2021 Comment 9 Device Comment Data Name : COMMENT Device Name SD647 File register capacity SD648 File register block number SD650 Comment drive SD651 Comment file name SD652 Comment file name SD653 Comment file name SD654 Comment file name SD655 Comment file name SD656 Comment file name SD670 Parameter valid drive info. SD671 Backup/restore state display SD672 Backup time(year,month) SD673 Backup time(date,hour) SD674 Backup time(minute, second) SD675 Backup information SD676 Restore time(year,month) SD677 Restore time(date,hour) SD678 Restore time(minute, second) SD679 Backup data restore information SD681 Prog memory writing(transfer)sts SD682 Program memory rewrite count SD683 Program memory rewrite count SD686 Std ROM writing(transfer)sts SD687 Standard ROM rewrite count SD688 Standard ROM rewrite count SD695 Set count standard ROM writing SD715 IMASK instruction mask pattern SD716 IMASK instruction mask pattern SD717 IMASK instruction mask pattern SD718 Accumulator SD719 Accumulator SD774 PID limit setting(differential) SD775 PID limit setting(differential) SD778 COM inst. exec. refresh select SD781 IMASK instruction mask pattern SD782 IMASK instruction mask pattern SD783 IMASK instruction mask pattern SD784 IMASK instruction mask pattern SD785 IMASK instruction mask pattern SD794 PID limit set(Not differential) SD795 PID limit set(Not differential) SD840 Debug function usage condition SD1000 Fuse blown SD1002 I/O module verification error SD1005 AC DOWN counter SD1008 Self-diagnosis error SD1009 Annunciator detection SD1015 Operating status of CPU SD1017 Scan time SD1018 Scan time SD1019 Scan time SD1021 Scan time 12/11/2021 Comment 10 Device Comment Data Name : COMMENT Device Name SD1022 1 second counter SD1025 Clock data SD1026 Clock data SD1027 Clock data SD1028 Clock data SD1035 Extension file register SD1091 Detailed error code SD1100 Fuse blown module SD1101 Fuse blown module SD1102 Fuse blown module SD1103 Fuse blown module SD1104 Fuse blown module SD1105 Fuse blown module SD1106 Fuse blown module SD1107 Fuse blown module SD1116 I/O module verification error SD1117 I/O module verification error SD1118 I/O module verification error SD1119 I/O module verification error SD1120 I/O module verification error SD1121 I/O module verification error SD1122 I/O module verification error SD1123 I/O module verification error SD1124 Annunciator detection quantity SD1125 Annunciator detection number SD1126 Annunciator detection number SD1127 Annunciator detection number SD1128 Annunciator detection number SD1129 Annunciator detection number SD1130 Annunciator detection number SD1131 Annunciator detection number SD1132 Annunciator detection number SD1300 Fuse blown module SD1301 Fuse blown module SD1302 Fuse blown module SD1303 Fuse blown module SD1304 Fuse blown module SD1305 Fuse blown module SD1306 Fuse blown module SD1307 Fuse blown module SD1308 Fuse blown module SD1309 Fuse blown module SD1310 Fuse blown module SD1311 Fuse blown module SD1312 Fuse blown module SD1313 Fuse blown module SD1314 Fuse blown module SD1315 Fuse blown module SD1316 Fuse blown module SD1317 Fuse blown module SD1318 Fuse blown module SD1319 Fuse blown module 12/11/2021 Comment 11 Device Comment Data Name : COMMENT Device Name SD1320 Fuse blown module SD1321 Fuse blown module SD1322 Fuse blown module SD1323 Fuse blown module SD1324 Fuse blown module SD1325 Fuse blown module SD1326 Fuse blown module SD1327 Fuse blown module SD1328 Fuse blown module SD1329 Fuse blown module SD1330 Fuse blown module SD1331 Fuse blown module SD1400 I/O module verification error SD1401 I/O module verification error SD1402 I/O module verification error SD1403 I/O module verification error SD1404 I/O module verification error SD1405 I/O module verification error SD1406 I/O module verification error SD1407 I/O module verification error SD1408 I/O module verification error SD1409 I/O module verification error SD1410 I/O module verification error SD1411 I/O module verification error SD1412 I/O module verification error SD1413 I/O module verification error SD1414 I/O module verification error SD1415 I/O module verification error SD1416 I/O module verification error SD1417 I/O module verification error SD1418 I/O module verification error SD1419 I/O module verification error SD1420 I/O module verification error SD1421 I/O module verification error SD1422 I/O module verification error SD1423 I/O module verification error SD1424 I/O module verification error SD1425 I/O module verification error SD1426 I/O module verification error SD1427 I/O module verification error SD1428 I/O module verification error SD1429 I/O module verification error SD1430 I/O module verification error SD1431 I/O module verification error SD1780 Power off detection status SD1781 Power failure detection status SD1782 Power sup.1 stop detect counter SD1783 Power sup.2 stop detect counter R11 DATA MARKING INPUT MANUAL W0 PL HOMEPOS W8 CPU RUN W9 PL HOMEPOS 12/11/2021 Comment 12 Device Comment Data Name : COMMENT 12/11/2021 Device Name Comment T0 POWER ON T1 MASTAR ON T2 TP. CHENGE T3 FINISHED MARKING BY TIMER T4 TIMER END MARKING T5 TIMER ENDA MARKING T8 START MARKING MANUAL T9 REQUEST TRANSFER DATA MARKING T10 PRINT HEAD UP END T11 PRINT HEAD DOWN END T12 WORK CLAMP UP END T13 WORK CLAMP DOWN END T15 NUMBERING COUNTUP T16 DELAY MARKING MANUAL T17 TIMER RESET WARNING SS SALAH T18 timer reset warning T19 FINISH PROCESS T20 DELAY TO CHANGE TANGGAL T21 NUM.DATA UPDATE T22 NUM.DATA UPDATE START T24 SENSOR MIDLE T25 NUM. MOVE T26 NUM. START SIGNAL ON T27 NUM. FINISH T28 CUT SEND DATA AFTER COMPLETE T30 NUM.DATA MEMORY ALARM T31 RST CNT1 T33 REQ DATA TRANSFER T35 DELAY TO START MEASURE T37 REQUEST DATA TO DISPLAY ON HMI T40 TRANS DATA WHEN DCM NOT USED T42 TRANS DATA WHEN DCM USED T43 HOLD RESET THEN HOMEPOS T50 DELAY SEND DATA MARKING T55 TIMER AUTO CLAMP FIN T60 DELAY TO CHANGE BULAN T64 RESET TOSOK BEFORE STARTING T65 DELAY TO MEASURE T100 TIMER LOADING PLC T101 TIMER WARNING MC NOT READY T102 MOVE FOR HOME T103 Restart ALARM T104 timer refres hmi T105 timer loading plc T106 timer rst update timer T107 TIMER STOP MARKING BY SA T110 Print Head MOVE ALARM T111 Work Clamp MOVE ALARM T115 timer rst data timer loading T300 timer rst pryor U2 CHANNEL RS232 13