BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
A CIVIL WORKS
1 SITE CLEARANCE / MOBILIZATION WORKS
1.1 Clearing the site by removing the bushes, trees, concrete
pavement and hard surface whatever at site up to its
root depth including the layout work, marking the
trench, construction of permanent reference points along
each grid precisely in line and level. Constructing all
necessary
staff
and
labor
facilities
(Toilet,
accommodation, cooking site), with all necessary
electricity, sanitary and water supply system and
necessary partitions, CGI fencing (min. 10'-0" height)
with metal post and bracing, CGI sheet covered
walkway with metal post and truss etc. all complete as
per drawings and instruction of the Consultant.
1.00
L.S
108.00
nos
3.1 Earthwork in excavation in foundation etc. in all kinds of
soil including dressing of sides, timbering, pumping
water, ramming of bottom, lift upto bottom of
foundation and disposing of the non required excavated
materials out of the site and keeping the edge of
excavation and then returning stacked soil in 150 mm
layers by ramming and watering, including all necessary
shoring, propping, sheet piling and disposing all surplus
excavated earth out of site area including transportation
etc. all extra charges as per drawings, specifications and
instruction of A/E
362.76
m3
3.2 Providing and levelling with borrowed earth (as
approved by A/E) on the foundations, plinth coverage
area, floors and all other specified area in 150 mm layers
including watering, ramming with 85% compaction,
consolidating, dressing etc. as per specifications and
instruction of A/E.
453.45
m3
2 PILING WORK
2.1 Construction of 600 mm dia. Gravel pile of 9.0m length
by excavation in pile foundation by mechanical or
manual drill by rig, up to required depth (as per design
drawing), lifting up with shoring the hole, dewatering
within construction period and disposing the soil outside
of site or designated place as per drawing, specification
and instruction of the Consultant all complete. The cost
is inclusive of bentonite if required, testing of pile as per
relevalent indian standard, cost of providing and
pouring gravel by vibration method and mechanical
rammer into the excavated pile. (including tools and
plants)
3 EARTH WORKS
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
4 MASONRY WORKS & PARTITION WORKS
4.1 Providing and laying 230 mm thick or thicker first class
chimney made Brick Masonry Wall in cement mortar (1
cement: 4 sand) in foundation as per drawings,
specifications and instruction of A/E.
47.29
m3
4.2 Providing and laying 230 mm thick or thicker first class
chimney made Brick Masonry Wall in cement mortar (1
cement: 4 sand) in superstructure including nominal
reinforcement (2-7 mm dia torkari @ every 6 course
horizontally linked with 7 mm dia. @ 200 mm c/c) etc all
complete as per drawings, specifications and instruction
of A/E.
180.08
m3
4.3 Providing and laying 115 mm thick first class chimney
made Brick Masonry Wall in cement mortar (1 cement: 4
sand) in superstructure including nominal reinforcement
(7 mm dia torkari @ every 6 course horizontally) etc all
complete as per drawings, specifications and instruction
of A/E.
89.76
m2
5.1 Providing and laying Cement Concrete (1 cement : 1.5
sand : 3 Aggregate) excluding cost of centering,
shuttering and the cost of reinforcement etc in specified
area as per drawings, specifications and instruction of
A/E.
283.89
m3
5.2 Centering and shuttering 19mm thick marine plywood
(waterproof) form work for reinforced concrete
including all necessary propping, shoring and removal
of formwork as per drawings, specifications and
instruction of A/E.
1,966.73
m2
5.3 Providing, laying, fixing, bending and binding
reinforcement (Fe500) in position including all necessary
binding wire as per drawings, specifications and
instruction of A/E.
44,570.42
kg
5.4 Providing, laying, fitting and fixing in position of upto
150 mm thick NCP (1:1) finished precast coping with
M20 (1:1.5:3) as specified width on top of parapet wall
(350 mm - 450 mm thick) including reinforcement,
formworks, groove for water bead, epoxy sealant filling
on the joint between coping etc. all complete as per
drawing, specifications and instruction of A/E.
90.55
rm
5 CONCRETE WORKS
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
DOORS
6 ALUMINUM
PARTITION WORKS
&
WINDOWS
QUANTITY UNIT
AND
6.1 Providing and fixing aluminum windows using power
coated in approved colour, aluminum section (16
micron) including at least 5.5 mm clear / frosted glass as
specified using all accessories (EPDM marine quality
gaskets, stainless steel screws, anchor bolt (HILTY or
equivalent) and jointing elements, jointing to masonry
has to be set with first class specified Elastomer /
silicone on foam seal and all other necessary fittings all
complete as per drawings, specifications and instruction
of A/E. The fabrication shop drawings shall be
submitted by the contractor for approval prior to the
commencement of the job.
The cost includes fly mesh screen of SS of fabric as well.
Note: A "total" approach of sealing need to be addressed.
The sealant need to be approached prior to
commencement of work.
Aluminum Sliding Windows from section (101 x 45 x 1.5)
mm
72.28
m2
17.07
m2
6.3.1 Aluminum doors section of (101 x 45 x 1.5) mm sash 40 x
45 x 1.5 mm
7.79
m2
6.3.2 Aluminum Swing doors section of (101 x 45 x 1.5) mm
6.01
m2
6.2 Fabrication, supply & installation of using powder
coated bronze color anodized aluminum DOUBLE
GLAZED windows, casement, casement cum fix, fix
windows, double panel sliding with SS fly mesh shutter
of standard section (16 micron) with 5.5 mm clear float
glass, casement stay, handle, neoprine gasket, weather
pile, roller, vt. lock, hinge, door handle, door lock, tower
bolt, iron rod, nut bolt etc. complete set of hardware as
per drawing, specification, door / window schedule and
instruction of A/E.
6.3 Providing and fixing aluminum doors (single / double
panel) & partitions using powder coated in approved
colour, aluminum section (16 micron) including 12 mm
thick both side pre-laminated board / 5.5 mm thick
glass, all accessories (EPDM marine quality gaskets,
stainless steel screws, anchor bolt and joining elements),
jointing to masonry has to be set with first class specified
Elastomer/silicone on foam seal and all other necessary
fittings, all complete with all the necessary hardwares as
per drawings, specifications, door window schedule and
instruction of A/E. The fabrication shop drawings shall
be submitted by the contractor for approval prior to the
commencement of the job.
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
6.4 Providing and fixing aluminum partition using powder
coated in approved colour, aluminum section (16
micron) including 12 mm thick both side pre-laminated
board / 5.5 mm thick glass, all accessories (EPDM
marine quality gaskets, stainless steel screws, anchor
bolt and joining elements), jointing to masonry has to be
set with first class specified Elastomer/silicone on foam
seal and all other necessary fittings, all complete with all
the necessary hardwares as per drawings, specifications,
door window schedule and instruction of A/E. The
fabrication shop drawings shall be submitted by the
contractor for approval prior to the commencement of
the job.
28.38
m2
0.80
m3
18.63
m2
13.92
m2
7 WOODEN DOORS WORKS
7.1 Providing and fixing frames for doors with seasoned
salwood covered with 2 coats of bitumen on all surfaces
in contact with masonry or concrete works including
providing and fixing 19mm x 6mm flat iron holdfast
375mm long 6 nrs for doors fixed to frames with screws
and embedded in cement concrete of mix (1:1.5:3) or
Anchor Bolt (HILTI or Equivalent as approved by A/E)
as per drawings, specifications, instruction of A/E.
7.2 Providing and fixing in position 38/32mm thick machine
compressed teak finished solid core Salwood door shutter
fixed with 3 nos. of 125 mm brass / S.S. hinges to each
shutter with necessary brass / S.S. handle, tower bolt,
door stopper, door lock (best quality approved by A/E
made with provision of master key), door closer etc. all
complete as per drawing, specification and instruction of
A/E.
7.2.1 Factory made solid core single / double door shutter
made of 38 mm thick seasoned Salwood with machined
compressed teak finished on both side and 38mm x15mm
hardwood lipping and well matched veneering and
vertical grains on both faces of the shutter all complete
7.2.2 Factory made solid core single / double door shutter
made of 38mm thick seasoned Salwood with machined
compressed teak finished on both side and louver at
bottom and 38mm x15mm hardwood lipping and well
matched veneering and vertical grains on both faces of
the shutter all complete
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
8 FLOORING WORKS
8.1 Providing, filling and levelling 150 mm thick stone dust
packing of 40 mm down crushed aggregate with stone
dust in the propotion of 1 stone dust : 4 aggregate
including watering, ramming with proper 95%
compaction, consolidation etc all complete as per
specifications and instruction of A/E.
495.40
m2
8.2 Providing and laying 500 gauge polythene sheet
including 150 mm overlapping as per drawings,
specifications and instruction of A/E
185.58
m2
8.3 Providing and laying 75 mm thick P.C.C. (1:3:6)
including cost of shuttering works etc as per drawings,
specifications and instruction of A/E
19.13
m3
8.4 Providing and laying 100 mm thick P.C.C. (1:2:4) on the
floor and other specified area including cost of nominal
reinforcement (8mm dia @ 200c/c both ways), shuttering
works etc as per drawings, specifications and instruction
of A/E
188.22
m2
266.53
m2
8.6 Providing and laying ceramic tile (glazed or as approved
by A/E) on the wall of approved shade, size and pattern
including base cement plaster (1:3) with cement slurry
and jointed with grouting epoxy matched with the shade
of the tile all complete as per drawings, specifications
and instruction of A/E
89.10
m2
8.7 Providing and laying non-skid homogenous tile (fully
vitrified or as approved by A/E) for floor of approved
colour, shade, size and pattern laid on minimum 25mm
thick cement screed (1cement : 4sand) in flooring and
jointed with grouting epoxy matched with the shade of
the tile all complete as per drawings, specifications and
instruction of A/E.
223.44
m2
8.5 Providing and laying 25 mm or thicker screed (1 cement:
4 sand) on the floor inclusive of 3mm thick cement
punning (1 cement: 1 sand) and making equal squares
with strings of approved dimension including chipping,
cleaning and wetting the surface and curing the works as
per drawings, specifications and instruction of A/E
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
8.8 Providing and laying minimum 16 mm thick marble for
floor of approved colour, shade, size and pattern laid on
minimum 25 mm thick cement screed (1cement : 4 sand )
in flooring, staircase trade, riser etc as specified area and
jointed with white cement slurry mixec with pigment to
matched with the shade of the marble including
necessary moulding, grinding, polishing etc all complete
as per drawings, specifications and instruction of A/E.
158.98
m2
19.54
m2
9.1 Providing and laying 3 mm thick and 125 mm high neat
cement punning skirt over 12.5 mm thick cement plaster
(1 cement: 3 sand) on the wall inclusive of two or more
coat of primer and two or more coat of enamel paint
including chipping, cleaning and wetting the surface and
curing the works as per drawings, specifications and
instruction of A/E
119.02
rm
9.2 Providing and laying 125 mm high ceramic tile (fully
vitrified or glazed as approved by A/E) skirting on the
wall of approved colour and shade, size and pattern on
base cement plaster (1:3) with cement slurry and jointed
with grouting epoxy matched with the shade of the tile
all complete as per drawings, specifications and
instruction of A/E
194.08
rm
250.14
rm
8.9 Providing and laying minimum 18 mm thick cement
fibre board flooring of approved colour, shade, size and
pattern laid on MS angle, I section etc in flooring,
staircase trade, riser etc as specified area and jointed
with white cement board slurry mixec with pigment to
matched with the shade of the cement board including
necessary screws, anchor bolts, grinding etc all complete
as per drawings, specifications and instruction of A/E.
9 SKIRTING WORKS
9.3 Providing and laying minimum 19 mm thick and 125
mm high marble with moulding for skirting of
approved colour, shade, size and pattern laid on
minimum 12.5 mm thick cement plaster (1 cement : 3
sand) in wall and jointed with white cement slurry
mixed with pigment to match the shade of the marble
including necessary grinding, polishing etc all complete
as per drawings, specifications and instruction of A/E
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
10 FINISHING WORKS
10.1 Providing and laying 12.5mm thick cement plaster (1:4)
on the internal wall, ceiling (slab and beam), skirting etc
of good finishing including raking the joints, cleaning
and wetting the surface, curing the works including
Alkali resistance fibre reinforcement all complete as per
drawings, specifications and instruction of A/E
1,528.08
m2
660.21
m2
6.00
sets
25.08
m2
95.70
rm
19.54
m2
10.2 Providing and laying 20 mm thick cement plaster (1:4)
on the external wall, ceiling (slab and beam), skirting etc
of good finishing including raking the joints, cleaning
and wetting the surface, curing the works including
Alkali resistance fibre reinforcement all complete as per
drawings, specifications and instruction of A/E
10.3 Providing and laying decorative cement plaster (1:4) on
the external brick column from bottom to top of good
finishing including raking the joints, cleaning and
wetting the surface, curing the works including Alkali
resistance fibre reinforcement all complete as per
drawings, specifications and instruction of A/E
10.4 Providing and laying Black stone cladding of approved
colour, shade, size and pattern laid on including
minimum 12.5 mm thick plaster (1cement: 3 sand) in
wall and jointed with ordinary cement slurry mixed with
pigment to match the shade of the flag stone including
necessary grinding polishing etc all complete as per
drawings, specifications and instruction of A/E
10.5 Providing and laying Water bead (20 mm wide 8-12 mm
thick) cement plaster (1:3) along the edge of overhang,
Chhajja and other specified area including Neat Cement
Punning finish as per drawings, specifications and
instruction of A/E.
10.6 Providing and fixing acoustical mineral board false ceiling
including all necessary GI channel suspension grid,
clamps, hangers, screws, grips, anchor bolts etc all
complete as per drawings, specifications and instruction
of A/E
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
11 PAINTING WORKS
11.1 Providing and applying a good quality wall guard putty
(JK or Birla or Equivalent) on the interior surface (wall
and ceiling) in a perfect line and level including
necessary hacking, sanding of the surface with sand
paper etc all complete as per drawings, specifications
and instruction of A/E.
2,407.12
m2
11.2 Providing and painting with two or more coats of best
quality emulsion paint of approved colour and shade
over one coat of primer as per drawings, specifications
and instruction of A/E
1,528.08
m2
660.21
m2
11.4 Providing and painting with two or more coats of "Matt"
finish enamel paint of approved colour to give even
shade over one coat of primer as per drawings,
specifications and instruction of A/E
48.14
m2
11.5 Providing and painting with two or more coats of
"Chapra Polish" of approved colour and shade on the
wooden shutters as per drawings, specifications and
instruction of A/E
61.48
m2
11.6 Providing and painting (outside)with two or more coats
of best quality water repelent paint of approved colour
and shade over one coat of primer as per drawings,
specifications and instruction of A/E
25.08
m2
412.68
m2
21.78
rm
11.3 Providing and painting with two or more coats of best
quality exterior weather coat paint of approved colour
and shade over one or two coat of primer as per
drawings, specifications and instruction of A/E
12 MISCELLANEOUS WORKS
12.1 Providing and applying with at least two coats (or as
manufacturers' specification) of best quality approved
water proofing as per drawings, specifications and
instruction of A/E
Crystalline water proof
12.2 Supplying and fixing MS railing on staircase as per
design with brass shoe all complete as per drawing,
specification and instruction of Consultant.
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
12.2.a Supplying and fixing Wooden Handrail on staircase as
per design with all complete as per drawing,
specification and instruction of Consultant.
21.78
rm
12.3 Providing and Construction of counter of RCC slab of
minimum 135 mm thick including reinforcement,
including of the 19mm thick Granite top of with
moulding of approved colour, shade, and type with the
necessary re-bar, formwork, brick masonry on cement
mortar, plaster works, painting over one coat of primer
etc. as per drawings, specifications and instruction of
A/E
5.78
m2
1,275.65
kg
77.00
rm
270.00
m2
18.00
nos.
1.00
set
12.4 Providing, fitting and fixing MS Metal sections,
Rectangular Pipes, I-beams, Channels of Yst 250 vertical
post, rafters and purlins inclusive of necessary bearing
plates, base plates, wall plate pipes, nut bolts, expansion
bolts of minimum 300, washer, anchor bolts, hilty bolts
etc. and requirement of all welding, grinding, polishing,
painting with two or more coats of approved quality and
colour enamel paint over two coat of anticorrosive paint
as an primer as per drawings, specifications and
instruction of A/E
RATE
12.5 Providing, fabricating and fixing MS metal grating
works cover for the drains of approved design with
necessary MS angles, strips, screws, anchor bolt etc
including two or more coats of approved colour enamel
paint over two or more coats of anticorrosive primer and
proper welding of all the joints all complete as per the
drawings, specifications and instruction of A/E.
12.6 Interlocking Concrete Block
Supplying and laying 70 mm thick heavy duty
interlocking concrete block of approved shape and size
with two colour laid in pattern in exact line and level as
shown in drawing on well compacted base to prevent
uneven settlement including 50 mm cruser stone dust or
fine sand as cusin including transportation and all
complete according to drawing and specification and
instruction by A/E.
13 GRASS WORKS
13.1 Providing and growing low height herbs / shrubs
including all the finishing of the top soil, compaction,
backfilling etc all complete as per the instruction of
qualified-nursery and instruction of A/E.
14 PROJECT CLOSURE
Supply a fully computerized set of as-built drawings for
all the buildings - architectural all complete with
approval of A/E.
(A) CIVIL WORKS TOTAL=
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
B WATER SUPPLY AND SANITARY WORKS
1
1.1
1.2
Water Supply Works
Chlorinated PolyVinal Chloride (CPVC) water supply Pipe
Providing and fixing in position SDR 11 (ASTM 2846)
CPVC pipes with all necessary SDR 11 (ASTM D 2846)
and brass mounted fittings, reducer, socket, union, plug,
clamp, crossover, fittings, tee, cross, bend, elbow (male
and female), reducer, socket, union, plug, clamp,
omega, transition piece, etc. for complete installation .
Installation of pipes including cutting and Solvent
CEMENT: Astm F 493 joining the pipe making holes on
walls and floors and repairing the same to original
finish all complete with testing and ready for operation
as per drawings, specificationss and instruction
i) 32 mm diameter
10.00
Rm
ii) 25 mm diameter
56.00
Rm
iii) 20 mm diameter
70.00
Rm
iv) 15 mm diameter
15.00
Rm
i) 32 mm diameter
2.00
Set
ii) 25 mm diameter
5.00
Set
iii) 20 mm diameter
5.00
Set
iv) 15 mm diameter
4.00
Set
2.00
Set
Valves
1.2.1 Ball Valves
Providing and fixing in position CPVC quarter turn ball
valve all complete with testing and ready for operation
as per drawings, specifications and instruction
1.2.2 Air Release Valves
Providing and fixing in position preeti or Utam or
equivalent gunmetal/brass air relief valves at summit of
vertical water main all complete with testing and ready
for operation as per drawings, specifications and
instruction
i) 25 mm diameter
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
1.2.3 Check Valves
Providing and fixing in position shakti or Utam or
equivalent gunmetal/brass non return check valves at
suction and delivery pipes all complete with testing and
ready for operation as per drawings, specifications and
instruction
i) 25 mm diameter
1.00
Set
1.00
Set
1.00
Set
1.00
No
1.2.4 Float Valves
Providing and fixing in position G.M. float valve all
complete with testing and ready for operation as per
drawings, specifications and instruction
i) 40 mm diameter
1.3
Centrifugal Pump
Providing and installation of Centrifugal pump with
induction motor. The centrifugal pump should be
directly coupled to induction motor with flexible
coupling and fixed in the single base frame. Preferred
brand of pump: Kirloskar or Pedrollo or Crompton or
equivalent. Installation including necessary fittings,
connection to suction and delivery lines, electrical
connection. The pumps should be connected to
generator and back up system opeations. All complete
with testing and ready for operation as per drawings,
specifications and instruction
i) 2 HP
1.4
Over Head Water Tank
Providing and fixing in position Hilltake Roof top or
equivalent HDPE overhead heavy duty water tanks for
storing water for flushing, including inlet, outlet,
overflow, washout vent pipe and necessary accessories
all complete with testing and ready for operation as per
drawings, specifications and instruction
Capacity 3000 liters
1.5
Iron Section Stand
fabrication and fixing in position I.S. or B.S. standard
iron section (to support 6x2000 HDPE water tanks) with
two coat primer painting with necessary accessories all
complete with testing and ready for operation as per
drawings, specifications and instruction
600.00
kg
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
1.6
Drinking Water filter
Providing and fixing in position water filter of 9-12 lit
capacity containing RO, TDS controller and disinfection
unit with necessary fittings complete with water testing
and ready for operation as per manufacturer’s
recommendations and instruction
1.00
Motor Strater Switch/Control Panel Board
Supplying and fixing motor starter switch all
completewith testing and ready for operation as per
manufacturer’s recommendations and instruction
1.00
No
Auto Sensor for pump
Supplying and fixing auto sensor for pump and
overhead tank including water proof cable with
contractor all complete with testing and ready for
operation as per manufacturer’s recommendations and
instruction
1.00
No
Solar hot water system
Supply,Installation and fixing in position of 8 nos of
solar panel capacity of 800 ltr. ( Locally Fabricated) Hot
water tank including 2 sets of 2.0 KW electric booster
with automatic thermostat
1.00
1.7
1.8
1.9
2
Set
Set
Hot Water Supply Works
Providing and fixing in position SDR 11 (ASTM 2846)
CPVC pipes with all necessary SDR 11 (ASTM D 2846)
and brass mounted fittings, reducer, socket, union, plug,
clamp, crossover, fittings, tee, cross, bend, elbow (male
and female), reducer, socket, union, plug, clamp,
omega, transition piece, etc. for complete installation .
Installation of pipes including cutting and Solvent
CEMENT: Astm F 493 joining the pipe making holes on
walls and floors and repairing the same to original
finish all complete with testing and ready for operation
as per drawings, specificationss and instruction
i) 32 mm diameter
ii)25 mm diameter
iii)20 mm diameter
iv) 15mm diameter
5
10
40
11
Rm
Rm
Rm
Rm
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
2.1
Insulation of hot water pipe
Providing and fixing in position of insulation for Hot
water supply pipe line (10mm thick) Armacell aeroflox
or equivalent all complete with testing and ready for
operation as per drawings, specifications and instruction
of the Engineer.
i) 32 mm diameter
ii)25 mm diameter
iii)20 mm diameter
iv) 15 mm diameter
3
Sanitary Works
Providing and fixing in position of sanitary items with
necessary fittings complete with testing and ready for
operation
as
per
drawings,
specifications,
manufacturer’s recommendations and instruction
3.1
Floor mounted water closets (White Glazed)
Providing and fixing in position Parryware cat no
C0237/281 coupled closet or equivalent white glazed
floor mounted water closets with "P" or "S" trap with 3
and 6 liters capacity white glazed dual flushing cistern
including CP flushing bend, CP angle valve, CP
connector, connection pipe,CP Spray, CP Cap, CP
Nipple,flushing valve connection to water and soil lines
all complete with testing and ready for operation as per
drawings, specifications and instruction of the engineer.
3.2
Rm
Rm
Rm
Rm
7.00
Set
7.00
Set
7.00
Set
7.00
Set
Hand drier
Providing and fixing in position Starmix or Germany or
equivalent hand drayer all complete accessories with
testing and ready for operation as per drawings, and
instruction
3.4
5
10
40
11
Counter Wash Basin (White Glazed)
Providing and fixing in position Hindware Starwhite
cat no 10080 or Parruware Special or Parruware Special
or equivalent 580x430 mm white glazed earthenware
counter wash basin with CI brackets, rubber plug stay
and chain, angle valves, feeder pipe, CP waste pipe,
bottle trap connection to water and waste water line all
complete ready for operation as per drawings,
specifications and instruction
3.3
QUANTITY UNIT
Mirror
Providing and fixing in position 600 mm x450 mm
belevelled edge 6 mm thick modiguard or equivalent
looking mirror with asbestos backing and CP screws,
clips all complete as per approval and instruction.
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
3.5
PARTICULARS
QUANTITY UNIT
Towel Rod
Providing and fixing in position CP towel rod 1.5 x 60
cm (1/2" x 24") heavy duty with caps and SS screws all
complete as per approval and instruction.
7.00
Set
7.00
Set
7.00
Set
7.00
Set
Providing and fixing in position European pattern or
American standard or equivalent glass shelf all complete
as per approval and instruction.
61.00
Set
3.10 Wash Basin Mixer
Providing and fixing in position 15 mm diameter Jaquar
or equivalent CP Single lever Basin Mixer without
popup waste system with 450mm long braided hoses,
cat no - 3001B , water connections and testing all
complete ready for operation as per approval and
instruction.
60.00
Set
21.00
Set
3.6
Robe Hook
Providing and fixing in position heavy duty American
Standard or equivalent CP Robe hook all complete as
per approval and instruction.
3.7
Toilet Paper Holder
Providing and fixing in position Porcelain clay toilet
paper holder (recessed type) American standard or
equivalent all complete as per approval and instruction.
3.8
Soap Dish
Providing and fixing in position (recessed type)
American standard or equivalent soap dish all complete
as per approval and instruction.
3.9
Glass Shelf
3.11 Two way angle valve
Providing and fixing in position 15 mm diameter CP
two way angle valve with wall flange and CP nipple
with water connections and testing all complete ready
for operation as per approval and instruction.
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
3.12 Soil, Waste, Rain and Vent PVC Pipes
Providing, Earthwork excavation, laying and installation
of panchakanya or equivalent PVC pipes with socket,
tee, wai, door vent, clean out, cowl, reducer, P trap, S
trap etc all complete installation, including laying,
cutting, jointing, making holes on walls or floor with
sleeves and repairing the same to original finish all
complete with testing and ready for operation as per
drawings, specifications and instruction
i) 50 mm diameter 6 kg/sq cm
60.00
Rm
ii) 75 mm diameter 6 kg/sq cm
50.00
Rm
iii) 110 mm diameter 6 kg/sq cm
60.00
Rm
iv) 160 mm diameter 6 kg/sq cm
60.00
Rm
7.00
2.00
No
No
i) 75 mm diameter
2.00
Set
ii) 110 mm diameter
2.00
Set
3.13 Multi floor trap with SS gratings
Providing and fixing in position hunter or equivalent
PVC multi floor trap with stainless steel gratings all
complete including waste line connections, cutting
floors and repairing to original position all complete
ready for operation as per drawings, specifications and
instruction
PVC floor trap 11 x 7.5 cm with SS grating
PVC floor trap 7.5 cm X 5 cm with SS grating
3.14 Gully Traps
Providing and fixing in position Panchakanya or
equivalent uPVC gully trap (75mm or 100mm dia. as
required) including waste connection, cutting floor,
ground and repairing to original position all complete
ready for operation as per drawings, specifications and
instruction.
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
RATE
3.15 Manhole with RCC Cover
Construction of manhole for soil, waste water and rain
water lines including excavation, back filling, reinforced
concrete foundation, brick masonry wall, hunching,
plaster, punning etc all complete with RCC Cover.
Depth of manhole depending upon site condition and
gradient of soil and waste lines. All complete with
testing and ready for operation as per drawings,
specifications and instruction
i) 600 mmx600 mm internal size
10.00
Set
1.00
Set
2.00
Set
i) Up to 1 kg.
15.00
Set
ii) 1 kg to 2 kg.
20.00
Set
iii) 2 kg to 3 kg.
10.00
Set
7.00
Set
3.16 Septic Tank
Construction of 3310 mm x 2200 mm x 1600 mm effective
internal sized septic tank with inlet chamber including
excavation, back filling, reinforced concrete foundation,
brick masonry wall, plaster, punning, inlet and outlet
pipes and drops, fittings, RCC slab cover, anti corrosive
painted CI steps etc all complete with testing and ready
for operation as per drawings, specifications and
instruction.
3.17 Soak Pit
Construction of 3000 mm effective internal diameter
and 2000 mm effective height soak pit with inlet
including excavation, back filling, honey cumb and solid
brick masonry walls, over burnt brick bats filling, RCC
slab cover, all complete with testing and ready for
operation as per drawings, specifications and
instruction.
3.18 Anchorage of GI, PVC pipes
Providing and fixing in position MS hanger or brackets
for vertically or horizontally laid pipes with necessary
nut, bolt, welding joints, drilling holes through
RCC/masonry structure wherever required, anchor bolt
and finish the surface complete including two coats of
anti-corrosive paint as per drawings, specifications and
instruction.
3.19 Fire Extinguisher
Providing and fixing in position 6 kg. Eversafe or
Minimax or equivalent ABC stored pressure type fire
extinguishers including wall mounting bracket and
necessary accessories all complete with testing and ready
for operation as per specifications and instruction
(B) WATER SUPPLY AND SANITARY WORKS TOTAL=
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
C ELECTRICAL AND ALLIED WORKS
A. Electrical System
1.Wiring of light/fan & power points:
1.10 Supply of materials and wiring with PVC Insulated
copper wire in PVC conduit without any joint in middle
of the span with necessary connecting, fixing, insulating
and jointing materials as per drawing and specification
complete (wire: Trishakti, Pioneer, Litmus or Equivalent)
1.1 Light/ Fan Points
{a} Light point with 2x2.5 Sq. mm/equivalent cu cable,
bends, circular & Junction boxes
{b} 2 way Light point with 3x2.5 Sq. mm/equivalent cu
cable, bends, circular & junction Boxes
1.2 Power Points
{a} 3 pin 6/16 A general outlet point with 2x4+1x2.5 sq.
mm / equivalent cu cable, bends, circular & Junction
Boxes
{b} International pin 11/13 A general outlet point with
2x2.5+1x1.5 sq. mm / equivalent cu cable, bends, circular
& Junction Boxes (double socket count as a point)
{c} AC point with 2x 4+1x2.5 sq. mm / equivalent cu
cable, bends, circular & Junction Boxes (separate circuit
for each point)
Sub Total
2. Light Fixtures:
2.10 supply of light fixtures, fixing, interconnection, testing
and commissioning complete with LED Panels (COB or
SMD), Holders, electronic ballast, capacitor with all
required mounting and fixing accessories as per drawing
and specification
Brands: PHILIPS, WIPRO, LEGERO, JAGUAR, FIAM OR
EQUIVALENT
{a} 600x300 mm LED Ceiling Panel 36-40 watt
{b} 300x300 mm LED Ceiling Panel 18-20 watt
{c} 120mm LED Ceiling COB Down Light 6 watt
{d} Internal wall light with E27, 7 W LED
{e} Battery pack EXIT light 5 watt LED
{f} 1x10 Watt LED Tube of 24" batten
{g} Outdoor half-head Light with 7 watt LED bulb (FWP
44118 or equivalent)
Sub Total
3. fan Fixtures:
3.10 Supply of fan fixtures, fixing, interconnection, testing
and commissioning all complete as per drawing,
specification and instruction
Brands: Vents Ukraine or equivalent
{a} IP45 150mm dia 220-315 m3/h, 1525-2060 RPM
Exhaust fan with outdoor SS grill cover
Sub Total
101
point
6
point
21
point
33
point
1
point
8
61
11
1
1
7
set
set
set
set
set
set
12
set
7
set
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
4. Switches and sockets
4.10 Supply of switches, sockets as mentioned below, 18 SWG
GI metal boxes , screw, and other necessary materials
with its Installation, Interconnection and commissioning
including civil works as per drawing , specification all
complete
Brands: Northwest, Schneider, Legrand or equivalent
17
4
12
2
2
21
41
29
6
{a} 10 A 1 Gang 1 way switch
{b} 10 A 2 Gang 2 way switch
{c} 10 A 2 Gang 1 way switch
{d} 10 A 3 Gang 1 way switch
{e} 10 A 4 Gang 1 way switch
{f} 5/6 pin 16 A switch socket
{g} international pin 11A socket
{h} 3 Flat pin 13A socket
{i} IR, PIT Sensor
set
set
set
set
set
set
set
set
set
Sub Total
5. Power Cable, Wire mesh Cable tray
5.10 Supply, delivery, laying and connecting of the following
Armoured/unarmoured power cable including cable
sockets, pull boxes and necessary materials. chiselling of
wall/ floors and redoing the chiselled area with cement
& sand mortar as per drawing and site condition all
complete.
Armoured/ Unarmoured cable (Pioneer, Trishkati,
Litmus or Equivalent)
{a} Cablofil - Electro zinc Steel wire Cable Tray as per
ISO20-81/82, NF/EN 12-329, DIN 50961.
i. CF 54/200, Std Length 3 mtr, D:54 mm, W: 200mm.
(000091)
ii. Kitasstr Coupler (Std Pack: 50 nos) CM5580 81
iii. TF Rod 8*1000 (CM8017 11)
iv. EEC8 Nuts (Std Pack: 100 nos) CM8012 11
v. RCSN 3000 Channel (CM0130 30)
vi. ED 1100 Side Channel (CM5582 01)
{b} 3.5C 50 sq. mm armoured copper cable laying
underground within PVC conduit [cable from DG to
ATS; COS to ATS; ATS to MPB]
{c} 4C 25+1x6 -E sq. mm armoured copper cable laying
within cable tray [cable from MPB to UPS via In - Out
Panel]
{d} 4x6+1x2.5 -E sq. mm Multistrend single core copper
wire laying underground within PVC conduit and
within tray [cable from MPB to FDBs - Normal supply]
{e} 2x6 sq. mm Multistrend single core copper wire
laying underground within PVC conduit and within tray
[cable from DB-UPS to FDBs]
Sub Total
4
12
12
24
2
2
nos
nos
nos
nos
nos
nos
50
rm
62
rm
26
rm
42
rm
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
6. Earthing and lightening protection system
6.10 Supply of materials and Installation of loke copper plate
(600x600x3.14 mm), 16 sq. mm copper bare conductor,
salt, charcoal dust, bare copper cable as per drawing
with solid CAD weld ( Brazing) & watering 32 mm dia
PVC pipe & its installation in a whole of 90x90x250 cm
with the layers of Earthing materials as per standard,
specification, drawing and refilling the ground all
complete.
6.20 Supply and installation of 16 sq. mm bare copper wire
with necessary copper lugs and copper nut bolts
connection with Earthing system on each Electrical
Closet as described on the drawing
6.30 60 m at level 3, Protection radius Rp(m) = 50 meter Early
Streamer Emission Lightning tip (stainless steel
470x60/590x120) , Mast for Lightening Arrestor, 75 sq.
mm copper strip bar without any joint in middle of the
span from Lightning tip to separate Earth Station. Make:
SCHIERTEC, Austria or Equivalent
6.40 25x3 mm Copper strip bar with mounting accessories
Sub Total
QUANTITY UNIT
3
set
50
rm
1
20
set
kg
1
set
7. Electrical Panel & Distribution Boards
Supply, Delivery, Installation and Commissioning of the
following Distribution Board Including copper Busbar
for individual taping of MCBs/ MCCBs, following
equipment housed in lockable, Double Door enclosure
made from 16 SWG HRCA Sheet metal and the
enclosure shall be finished at least of two coats of red
oxide metal primer and other two coats of final epoxy
enamel paint as per drawing and site condition (shop
drawing of all Distribution Boards shall submit to the
Consultant and get approval before starting the job)
Breaker: ABB, Siemens, Schneider or Equivalent
Fabricator: Himalaya, Hyonjan, Corona, NPEF OR
Equivalent
7.1 Main Panel Board - MPB
100 Amp Panel Board with copper Busbar and hardware 1 set
100A, TP MCCB - 1 set
Electronic Digital Volt Meter with 7 position Selector - 1
set
Electronic Digital Load Meter with 4 position Selector &
CTs - 1 set
Indication LED Light with 2 A MCB - 3 set
100 A TP MCCB - 1 set
50 A TP MCCB - 2 set
32 A TP MCCB - 2 set
30 A DP MCB - 2 set
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
7.2 FDB - Ground Floor
Normal section
40 A TP MCB - 1 set
32 A TP MCB - 1 set
16 A SP MCB - 6 set
6 A SP MCB - 6 set
UPS Backup section
32 A DP MCB - 1 set
25 A DP MCB - 1 set
10 A SP MCB - 10 set
1
set
7.3 FDB - First Floor
Normal section
30 A TP MCB - 1 set
16 A SP MCB - 6 set
6 A SP MCB - 6 set
UPS Backup section
25 A DP MCB - 1 set
6 A SP MCB - 10 set
1
set
7.4 100 A TP MCCB - 2 set ( incomer for 2 NEA source)
Indication LED Light with 2 A MCB - 6 set
16 SWG Metal enclosure & Busbar -1 set
7.5 100A TPN 4 Pole manual changeover switch
16 SWG Metal enclosure & Busbar -1 set
Sub Total
1
set
1
set
12
point
1
set
1
set
1
set
19
rm
12
set
B. Telephone system:
1.1 Supply of materials and wiring in PVC rigid conduit
concealed without any joint in middle of the span as per
drawing, specification all complete
{a} Telephone points with 3 Pair UTP Telephone cable
1.2 Supply, installation and interconnection of Telephone DF
with 1x10 way solder less crone for RJ-11 as per drawing,
specifications all complete
{a} Telephone CDF 400x500mm with hinge door and
lockable system including 1 set Solder less telephone
cable termination module 10 pair
{b} Telephone CDF 400x500mm with hinge door and
lockable system including 2 set Solder less telephone
cable termination module 10 pair
{c} Telephone CDF 400x500mm with hinge door and
lockable system including 1 set Solder less telephone
cable termination module 100 pair
1.3 RJ-11 cable
{a} 10 pairs UTP Telephone cable within PVC conduit
(for CDF interconnection) as per RJ-11 Cable riser
1.40 Supply, installation & interconnection of sockets of
approved make using proper tools in appropriate GI
metal boxes including civil works & accessories as per
drawing and specification complete. Make: Northwest,
Legrand, Schneider or equivalent
{a} RJ 11 Telephone socket
Sub Total
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
C. Computer Networking system:
1.10 Supply of materials and wiring in PVC rigid conduit
concealed/false ceiling without any joint in middle of
the span as per drawings, specification and instruction
all complete
{a} Computer LAN, WAP points with CAT 6 + gigabit
UTP cable - separate length for each socket
1.20 Computer CAT 6 cable (Make: Legrand, Schneider)
{a} CAT 6 + gigabit UTP Networking cable within 25 dia
PVC underground conduit for vertical uplink
1.30 Supply, installation and interconnection of Computer
networking Passive parts as per drawings, specifications
all complete.
{a} 250x300 mm sheet metal enclosure with hinged cover
for CAT 6 cable (for cable pulling, no cable joint shall be
made within box)
{b} 24 Port Patch panel for connecting CAT 6 UTP
network cable within 19" metal rack with required
Tag/jacks/termination modules - Schneider, Legrand
{c} Wall Mounting 19 inches Enclosed type Aluminium
Rack with required Cable manager etc. with patch cord Schneider, Legrand
1.40 Supply, installation & interconnection of sockets of
approved make using proper tools in appropriate GI
metal boxes, screw including civil works & accessories as
per drawing and specification complete
{a} RJ 45 Computer networking socket (Schneider,
Legrand or Equivalent)
Sub Total
D. Fire Alarming system:
1.10 Supply of materials and wiring in PVC FRLS rigid
conduit of approved make as per drawing
Fire alarm, RI, MCP & detector points with 2x1.5 sq. mm
FRLS copper wire
1.20 Supply, installation, interconnection and commissioning
of following fire alarm & detection accessories (Make:
Honeywell, System Sensor or Equivalent)
QUANTITY UNIT
34
point
36
rm
1
set
2
set
2
set
34
set
24
point
2
4
17
set
set
set
1
set
Surface Mounting Indoor use Crack glass fire call point
Spatial Sounder/Beacon
Smoke Detector
1.30 Supply, installation, interconnection, testing and
commissioning of CFP Standard 4 zone conventional Fire
Panel of Key switch version with 2x12V 3.3 A Hr VRLA
battery pack (system sensor)
Sub Total
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
E. IP Based CCTV and surveillance system:
1.10 Supply of materials and wiring in PVC rigid conduit
concealed/false ceiling without any joint in middle of
the span as per drawings, specification complete
{a} CCTV points with CAT 6 UTP cable
1.20 CCTV connection cable
{a} 4 pair CAT 6E Cable for CCTV system up to server
for IP based
1.30 Supply, installation, interconnection and commissioning
of High Resolution Colour CCTV camera with 1/3"
HAD CCD sensor including with lens, Stand and Power
Adaptor of approved make including mounting
arrangements and accessories as per drawing,
specification complete (make: Honeywell or Equivalent)
7
point
210
rm
7
set
RATE
Sub Total
Summary of Estimate (Electrical and Allied works)
1. Wiring of light/fan & power points
2. Light Fixtures
3. fan Fixtures
4. Switches and sockets
5. Power Cable
6. Earthing system
7. Electrical Panel & Distribution Boards
8. Telephone System
9. Computer Networking system
10. Fire alarming system
11. CCTV and surveillance system
(C) ELECTRICAL AND ALLIED WORKS TOTAL=
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
RATE
AMOUNT
REMARKS
D IT (DATA CENTER WORKS)
The items given in this schedule are provisional. The Contractor shall be paid for the actual quantity of work executed as measured
at the site at the rates tendered. The Owner reserves the right to increase or decrease any of the quantities, or to omit totally any
item of work. Any claim by the Contractor on these accounts will not be entertained.
1
2
Physical Infrastructure
Remove from existing server room and reinstall of
Raised Access Flooring
Remove and reinstallation of Flooring (600mm x 600mm
size 12" height) - labour only
Supply, delivery and installation of Insulation Nitrile
Sheet
56.00
pcs
480.00
sq.ft
Power & Network Management
Data Centre Electrical System
Complete Electrical Works inside Data Centre (Including
Modular dedicated UPS Panel, PAC Cabling) as per
attached specification with followings but not limited to:
1.00
lot
1.00
lot
1. Fire Resistant Cable Tray of 4" to 6" in size - 40 feet
(Separate Cable Tray for Power, Network & Telephone
Cabling)
2. Redundant Sockets for Each Racks of 32 Amp. C Type
Industrial Sockets - 10 sets
3. Emergency lights with bulb, holder and wires - 3
points
4. Powder Coated Panels– Separate for UPS & Grid
Power Supply - 2 sets
5. Hi and Low Voltage and Surge Power Protection
System - 2 sets
6. Separate & Redundant Double Pole MCB of each 32
Amp Power Socket - 10 sets
7. 32 Amp Power Socket Wiring with Sockets with
required Accessories - 5 pairs
8. Moduler type Panel - 4 sets
9. MCCBs/MCBs - 1 lot as per specification
10. Power cable 2 core 10sq. Mm - 100 mtrs
11. Power cable 4 core 25sq. Mm - 50 mtrs
3
Network & Rack Management of Data Centre
Complete Network works as per TIA Standard between
racks as per attached specification with followings but
not limited to:
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
PARTICULARS
QUANTITY UNIT
1. Hi Quality CAT 6 Pure Copper Cable with the
standard of TIA & UL - 1 job
Redundant (N+1) Network Cabling shall be done from
One Rack to Another
All labeling of wires and devices shall be done
2. CAT 6 Patch Panels with Keystone Jacks and Face
Plates for Network Monitoring Room, UPS Room and
Server Room - 1 job
3. Testing of Each Network Point and cabling report
shall be generated by Fluke meter for compatibility of
Gigabit networking
4. Patch Panel: 4 unit
5. Patch Cords (1,2,3 meters) : 100 units (multi-color)
6. Cat 6 UL Listed Cable with required Accessories and
keystones jacks: 2 rolls + accessories
7. Cable guide: 8 units
Remove, reinstallation and Commissioning of 42U
Server Rack with required Power Distribution Units
4
5
supply and installation of Automatic Transfer Switch
Rack Mountable Automatic Transfer Switch
3.00
set
1.00
lot
2.00
set
1.00
job
Data Centre Cooling
Single Split Wall Mounted Air Conditioning
Supply, installation, testing and commissioning of single
split wall mounted air-conditioning unit with Indoor and
Outdoor Unit, system with fully charged refrigerant (R410A) inclusive of interconnecting power and control
cables, Refrigerant pipes with insulation, Drainage pipe
with insulation, individual remote controllers and
supports made of MS angle/rods as per specifications
and drawings of following capacity: cooling/Heating
Capacity: 24000/26000 Btu/Hr.; Power supply: 215V230V-1PH-50HZ.
Fire Detection & Suppression
6
remove from existing place and reinstallation of Smoke
Detection System with Remote Monitoring
Remove from existing building, reinstallation and
Commissioning of fire alarm & Smoke Detection System
with existing Fire alarm control Panel
RATE
AMOUNT
REMARKS
BILL OF QUANTITY
CONSTRUCTION OF ELECTION COMISSION DATA CENTER BUILDING
UNDP ELECTORAL SUPPORT PROJECT (UNDP ESP)
KATHMANDU, NEPAL
S.NO.
7
8
9
PARTICULARS
QUANTITY UNIT
Data Centre Security
remove from existing place and reinstallation of IP Surveillance System
remove, reinstallation and Commissioning of IP
1.00
Surveillance System (4 Camera + NVR)
supply and laying of CAT6 cable within FRLS grade
120.00
PVC conduit for CCTV
Fire Resistant Metal Door and Biometric Access Control System
2 hours Fire Rated Door
reinstallation of existing 11 KVA UPS With Battery
Backup
Disconnect, Remove, reinstallation and Commissioning
of 11KVA UPS
Disconnect, Remove, reinstallation Battery Backup
RATE
job
mtr
2.00
pcs
2.00
pcs
64.00
pcs
(D) IT WORKS TOTAL=
AMOUNT
REMARKS