Effect of Red, Blue and White LED Lights on Mung Beans’ Growth A Capstone Proposal Presented to the Faculty of the SENIOR HIGH SCHOOL DEPARTMENT Himamaylan National High School In Partial Fulfillment of the Requirements for the Course SCIENCE, TECHNOLOGY, ENGINEERING AND MATHEMATICS (STEM) STRAND By FAYE LOUISE LOPEZ JUSH BRYAN DOJOLES ROSEMARIE D. JUAREZ ESAYA M. PEREZ Subject Adviser May 2021 CHAPTER 1 INTRODUCTION 1.1 Rationale of the Study Light directly influences plant growth and flowering by inducing photosynthesis and feeding plants energy. Plants are dependent on light to generate food, induce the growing cycle and allow for healthy development (Smestad, 2017). In recent advances, light-emitting diodes (LEDs) have remarkable potential as supplemental source of light for promoting plant growth (Rehman et al., 2017). In this time of pandemic, many plantitos and plantitas tends to use ‘planting’ as their hobby. Light emitting diode (LED) lights are often used to encourage plant growth. Plants utilize different wavelengths of light to promote vegetative growth and flowering and LED lights are very efficient and capable of producing the type of light needed by plants (Leone, 2017). Not only are LEDs great for encouraging plant growth, they are very energy-efficient (Leone, 2017). EarthEasy.com claims that LEDs are a type of “energy-efficient lighting”. Unlike most types of light bulbs, LEDs require very little power to produce light. LEDs offer a number of advantages over high-pressure sodium, incandescent, fluorescent, and metal halide lamps, including less heat emission, longer fixture life, instant on/off operation with no effect on operating life, greater energy efficiency, more localized targeting of light emission, and the ability to provide light at specific wavelengths (Walker et al., 2020). According to Ryan Raman,MS,RD, on an article in healthline.com, Mung beans or Vigna Radiata are small, green beans that belong to the legume family. He then added that they’re high in nutrients and believed to aid many ailments. According to the Office for Disease Prevention and Health Promotion, evidence has shown that legumes, such as mung beans, can be part of a healthful eating pattern. Research also suggests that plant-based diets are a vital way for people 1 to improve their health, and reduce the risk of variety of chronic illnesses. Eating mung beans can be a good way of getting more plant-based food in a person’s diet. Schematic Diagram Mung Beans Cultivated with White LED light Mung Beans Cultivated with Red and Blue LED light Plant Growth a. Height b. Number of Leaves c. Size of Leaves 1.2 Statement of the Problem LED manufacturers offer different colors of light. Commonly available colors of LEDs are blue, green, red, and yellow. This study seeks to find the comparison of the effects of Red, Blue and White LEDs to the growth of Mung Beans. This study also claims to help the farmers and plant growers to determine what is the best LED light color to be use when planting mung beans. Getting to know whether it is best to use white, red or blue LED lights on growing mung 2 beans is important for it can help people produce more energy-efficient mung beans in the comfort of their homes. Specifically, this study aims to answer the following: 1. What is the measurement of plant growth when cultivated with the use of colors blue, green, red, and yellow LED lights in terms of: a. Height; b. Number of Leaves; c. Size of Leaves? 2. Is there a significant difference between the growth of plants that was cultivated with the use of colors blue, green, red and yellow LED lights and with use of natural sunlight in terms of: a. Height; b. Number of Leaves; c. Size of Leaves? 1.3 Significance of the Study This study will be undertaken to find out the effects of red, blue, and white LEDs on the growth of mung beans plant. Benefiting the study are the various sectors as follows: The Farmers and Plant Growers They would be able to understand the pros and cons of using red, blue, and white LED light colors on the growth of mung beans and produce more energy-efficient mung beans. The Environment The environment will benefit because plants play an important part in the food chain. This study would also know the best energy-efficient way to grow plants using LED lights. 3 The Researchers They would be able to identify what is/are the best possible outcome in using red, blue, and white LED lights on the growth rate of mung bean plants. 1.4 Scope and Limitation of the Study This study focuses on the effects of red, blue, and white LED lights on the growth of Mung beans. The study will be using LED lights with colors such as red, blue, and white as a source of light to nine mung beans. The data collection will be conducted by observing the growths of the nine mung beans in different LED light colors for 21-31 days in an indoor environment. This study will be conducted at Juarez’s residence in Brgy. Consuelo, Ilog, Negros Occidental on the last week of June, year 2021. There are many kinds of plants that can also grow with the use of LED lights, however, the researchers will only use the Mung bean plants and will not use any other kinds of plants. LED light colors could also affect the plant’s nutrient value, however, researchers will only focus on observing the effects of red, blue, and white LED light colors on mung bean’s plant growth. 1.5 Definition of Terms The terms used in this study will be defined conceptually and operationally, these are the following: LED (Light Emitting Diode). This is a semiconductor device that emits visible light of a certain color, and is fundamentally different from conventional light 4 sources such as incandescent, fluorescent, and gas-discharge lamps (Strandberg, et al., 2012). In this study, this term refers to the lights that the experimental subject will be treated off. Also in this study there will be only three colors of LED will be used such as red, blue, and white. Mung Beans (Monggo Plant). According to an article in Panlasang Pinoy, the monggo, also known as Vigna radiata, originates from the legume or bean family or Leguminosae. Their popularity is manifested in their wide usage throughout Asia, especially in China, and Southeast. Plant Growth. According to Brukhin (2011), this the increase of plant volume and/or mass with or without formation of new structures such as organ, tissues or cell organelles. In this study, this terms refers to the measurement of the plant (Mung Beans or Munggo plant) on the experimental subject when cultivated naturally and when cultivated with treatment. CHAPTER 2 Review of Related Literature This chapter present series of literature related to this study where various concepts and ideas are taken from various authors. Furthermore, this chapter aims to enhance and enrich the understanding to the researchers well accordance to this study, the following are the literature related to the effects of LED light colors on plant growth. 2.1 Effects of Light-Emitting Diode 5 On the study of Olle and Virsele, (2013), which is about food and agriculture and entitled “The Effects of Light-Emitting Diodes on greenhouse plant and quality; aims to present LED light effects on photosynthetic ideas, growth, yield, and nutritional value in green vegetables and tomato, cucumber, sweet pepper transplants. The sole LED lighting was applied in a closed growth chambers, as well as combinations of LED wavelengths with conventional light sources, fluorescent and high pressure sodium lamp light, and natural illumination in greenhouses are overviewed. On their study, red and blue light are basal in the lighting spectra for green vegetables and tomato, cucumber, and pepper transplants; far from red light, important for photo morphogenetic processes in plants also results in growth promotion. However, theoretically unprofitable spectral parts as green and yellow also have physiological effects on investigated plants. Presented results disclose the variability of light spectral effects on different plant species and different physiological indices. Also various researches were cited on their study. According to Mitchell et al. 2012, LED represent a promising technology fo the greenhouse industry that has technical advantages over traditional lighting sources, but are only recently being tested for horticultural applications. Also it has been stated that major advantage of LEDs over all the lamp types for plant lightings is that the technology is evolving in electrical-use efficiency at a rapid pace. Another study is “Effects of Blue and Green Light on Plant Growth and Development Effects of Blue and Green Light on Plant Growth and Development at Low and High Photosynthetic Photon Flux” which was studied by Snowden, 2015. According to his study, the optimal combination of wavelengths of light (spectral quality) for single leaf photosynthesis has been well characterized, but spectral quality is not well characterized in whole plants in long-term studies. He reports the effects of eight light spectra at two photosynthetic photon fluxes (200 and 500 µmol m-2 s-1) on dry mass, leaf area index and net assimilation of seven species in replicate 21-day studies. The combination of treatments allowed us to separately assess the effects of blue and green light fraction among species and PPF. At a PPF of 500, increasing blue light from 11 to 28 % significantly decreased 6 dry mass in tomato, cucumber, and pepper, but there was no significant effect on soybean, lettuce and wheat. At a PPF of 200, dry mass significantly decreased only in tomato across the blue light range. Effects on leaf area paralleled effects on dry mass in all species at both PPFs, indicating that the effects of blue light on dry mass were mediated by changes in leaf area. Contrary to predictions of net assimilation based on blue light response of single leaves, there was no evidence of decreasing net assimilation with increasing blue light. In contrast to the significant effect of blue light dry mass and leaf area, increasing green light fraction from zero to 30 % resulted in few significant differences. Contrary to several reports on significant green light effects on growth (both increases and decreases), we found no consistent effect of green light among species on growth, leaf area or net assimilation. Collectively, these results indicate significant differences among species in sensitivity to blue light and less sensitivity to green light, and that the effect of blue light on dry mass is primarily determined by changes in leaf area. Micheal Snowden has been influenced by the concept and ideas photobiology, thus as a master of science he begins to study and explore about it. Thus, he came up to the theory and started working about it. Research in photobiology dates back over 200 years with studies using primitive light sources. This early research identified photoreceptors and action spectra for specific regions of the light spectrum that are paramount for photosynthesis as well as growth and development that are still topics of interest today. Photobiological research has become an area of increasing interest since the introduction of lightemitting diodes which allow for evaluating endless combinations of light spectra. Red light-light emitting diodes were the first to be introduced that had an electrical efficiency comparable to existing light sources. The research found that red light alone was not sufficient to promote normal plant growth and development in most species and that some blue light supplementation was needed. The amount of blue light required has been extensively studied with varying results. The introduction of light emitting diodes has also allowed for studies of the effects of green light on plant growth and development. The influence of green light, similar to blue light, 7 has resulted in varying conclusions, mainly regarding the importance of green light for photosynthesis. The study of Saleem et al. 2019, focuses on the field of annals of agriculture and crop science specifically they studied the Effect of Different Colors of Lights on Growth and Antioxidants Capacity in Rapeseed Seedlings. Light is the key factor for the better growth and development of plant that directly fluctuates biosynthesis of many secondary metabolites. Moreover, light is most important abiotic factor that play very important role in photosynthesis and morphogenesis in the plants body. Therefore, it is very necessary to provide appropriate amount of light for a healthy and normal growth of plant body. The aim of the present study to evaluate the growth and antioxidant capacity of rapeseed using White Light (WL), Dark Red Light (DL), Mixed (red + dark red lights) (ML), Red Light (RL), Blue Light (BL) and Orange Light (OL). Artificial Light Emitting Diodes (LEDs) were used in this experiment in the glass house environment. The lights were provided with LEDs with the peak wavelength of WL 390nm, DL 670nm, ML 650nm, RL 660nm, BL 450nm and OL 610nm. The results revealed that DL, ML and RL promoted plant growth, photosynthetic pigments while BL and OL undergoes high stress and reduced plant growth and photosynthetic pigments when compared with WL. Moreover, the antioxidants enzymes i.e. Superoxidase Dismutase (SOD), Peroxidase (POD) and the contents of Malondialdehyde (MDA), proline and total soluble protein also play very important role when plant undergoes any environmental stress. The results revealed that BL and OL induced high values of SOD, POD, MDA, proline and total soluble protein undergoes high level of stress while DL, ML and RL showed low light stress. Saleem et al. 2019, concluded that OL and BL reduced growth and photosynthetic pigments in rapeseed seedlings while DL, ML and RL promote plant growth and photosynthetic pigments and thus can be used as industrial scale to fulfil market demand of rapeseed oil. Another related study is “Effects of Light Quality on Growth and Phytonutrient Accumulation of Herbs under Controlled Environments”, studied by Dou, et al. 2017 which focused in the field of horticulture. In recent years, consumption of herb products has increased in daily diets, contributing to the 8 prevention of cardiovascular diseases, chronic diseases, and certain types of cancer owing to high concentrations of phytonutrients such as essential oils and phenolic compounds. To meet the increasing demand for high quality herbs, controlled environment agriculture is an alternative and a supplement to field production. Light is one of the most important environmental factors influencing herb quality including phytonutrient content, in addition to effects on growth and development. The recent development and adoption of light-emitting diodes provides opportunities for targeted regulation of growth and phytonutrient accumulation by herbs to optimize productivity and quality under controlled environments. For most herb species, red light supplemented with blue light significantly increased plant yield. However, plant yield decreased when the blue light proportion (BP) reached a threshold, which varied among species. Research has also shown that red, blue, and ultraviolet(UV)light enhanced the concentration of essential oils and phenolic compounds in various herbs and improved antioxidant capacities of herbs compared with white light or sunlight, yet these improvement effects varied among species, compounds, and light treatments. In addition to red and blue light, other light spectra within the photosynthetically active region—such as cyan, green, yellow, orange, and far-red light—are absorbed by photosynthetic pigments and utilized in leaves. However, only a few selected ranges of light spectra have been investigated, and the effects of light quality (spectrum distribution of light sources) on herb production are not fully understood. This paper review show light quality affected the growth and phytonutrient accumulation of both culinary and medicinal herbs under controlled environments, and discusses future research opportunities to produce high quantity and quality herbs. Another set of authors collaborated to create a research study about LightEmitting Diodes also known as LED. Rehman, et al. (2017), explore a field in Environmental Science and Pollution Research specifically studying “LightEmitting Diodes; whether an efficient source of light for indoor plants. Availability of sufficient light for growth optimization of plants in greenhouse environment during winter is a major challenge, as light during winter is significantly lower than 9 that in the summer. The most commonly used artificial light sources (e.g., metal halide lamps, high pressure sodium lamps, and high fluorescent lamps) are of low quality and inefficient. Therefore, better options should be developed for sustaining agricultural food production during low levels of solar radiation. In recent advances, light-emitting diodes (LEDs) have remarkable potential as supplemental source of light for promoting plant growth. LEDs are novel and versatile source of light with cool emitting surface, wavelength specificity, and low electric power requirement. In the present study, we provided a contemporary synthesis of existing evidence along with our hypothetical concepts to clarify how LED approach could be an efficient and cost-effective source of light for plant growth and development especially in closed production system. In comparative analysis of common artificial vs. LED lighting, we revealed that spectral quality of LEDs can have vivid effects on plant morphogenesis and anatomy. We also discussed the influence of different colors of LEDs on growth performance of plants and provided the cost benefit analysis of using LEDs compared with other traditional sources. Overall, we hope that this article will be of great worth in future due to its practical implications as well as research directions. An article in Acta Horticulturae was published on November 2018 which was written by Bian, et al. The article is entitled “Uncovering LED light effects on plant growth: new angles and perspectives – LED light for improving plant growth, nutrition and energy-use efficiency”. Light supplementation can increase crop yield in greenhouses by promoting photosynthesis and plant growth. However, the high energy costs associated with light supplementation are a predominant factor that limits development and profit improvement of controlled environment agriculture. Light-emitting diodes (LEDs) are a promising technology that has tremendous potential to improve irradiance efficiency and to replace traditionally used horticultural lighting. Compared with traditional light sources (e.g., high-pressure sodium lamps and metal halide lamps) used in crop production, LEDs have distinct advantages, such as their small size, long lifetime and high photoelectric conversion efficiency. Most importantly, as a monochromatic light source, the spectrum of LEDs can be adjusted based on plant growth requirements. This 10 project aimed to investigate energy-use efficiency, vegetable nutrition and photosynthesis improvement of light supplementation in a protected horticulture system. In the initial phase, the effects of LED light on plant growth and light-use efficiency for pak choi and photosynthetic performance were investigated. The results showed that the highest fresh and dry weight and leaf area were observed under red and blue LED light, with the blue light percentage at 23%. Compared with fluorescent lamps (FL) with photosynthetic photon flux density (PPFD) at 220 μmol m-2 s-1, the light-use efficiency increased by 55, 114 and 115% for mixed red and blue LEDs with PPFD at 100, 150 and 220 μmol m-2 s-1, respectively. Monochromatic red- and blue-light LEDs resulted in significant decreases in Pn of tomato plants, but the stomatal conductance (Gs) for monochromatic blue LEDs was higher than that for FL. The effect of light spectrum composition on lettuce nutrition quality was also studied. Continuous light with combined red, green and blue LEDs exhibited a remarkable decrease in nitrate. Moreover, continuous LED light for 24 h significantly increased phenolic compound content and free-radical scavenging capacity in lettuce leaf. 2.2 Plant Growth Plant growth could be defined as the increasing of plant volume and/or mass with or without formation of new structures such as organs, tissues, cells or cell organelles. Growth is usually associated with development (cell and tissue specialization) and reproduction (production of new individuals). The study of Brukin & Morozova (2011) had provided a big help in the field of biological science. Their study was about plant growth and development. One of the most intriguing questions in life science is how living organisms develop and maintain their predominant form and shape via the cascade of the processes of differentiation starting from the single cell. Mathematical modeling of these developmental processes could be a very important tool to properly describe the complex processes of evolution and geometry of morphogenesis in time and space. Brukin & Morozova’s study summarizes the most important biological knowledge on plant development, exploring the different layers of investigation in developmental 11 processes such as plant morphology, genetics, plant physiology, molecular biology and epigenetics. As knowledge on the fundamentals of plant embryo genesis, growth and development is constantly improving, they gather the latest data on genetic, molecular and hormonal regulation of plant development together with the basic background knowledge. Special emphasis is placed on the regulation of cell cycle progression, on the role of the signal molecules phytohormones in plant development and on the details of plant meristems (loci containing plant stem cells) function. they explore several proposed biological models regarding regulating plant development. The information presented here could be used as a basis for mathematical modeling and computer simulation of developmental processes in plants. Plants sustain life on earth by producing the oxygen that living organisms need to survive. They play a critical role in the food web, transferring energy to other living organisms as they are consumed (eaten). However, the specific purpose of each individual plant is to produce its own food so that it can reach maturity and reproduce. Since sunlight provides the necessary energy for photosynthesis, it is one of the most important influences on a plant’s growth. However, several other factors also influence the rate of plant growth. These include the temperature of the air and the temperature of the soil the plant's roots are growing in. These factors help determine when agricultural crops will be planted and when those plants will be ready for harvesting. For example, seed producers calculate the necessary number of days of optimal air temperature (the temperature at which a plant will grow best) for a specific plant variety to reach maturity. Agricultural producers then choose between plant varieties, matching the season and conditions with the "growing degree days," referred to as "growing degree units" or "heat units." Rather than maintaining consistent air and soil temperatures year-round, Kansas experiences four distinct seasons: spring, summer, fall, and winter. The spring season brings mild weather and higher rainfall so most plants will grow faster during the spring. Once the soil warms up enough for the seeds to germinate, crop producers plant spring crops, including corn, soybeans, grain sorghum, sunflowers, fruits, and vegetables. During the summer 12 season, warmer temperatures continue to encourage plant growth. Many plants also mature and produce seeds or fruit, like wheat, cotton, and tomatoes. The fall season brings cooler temperatures, and there is less sunlight available for photosynthesis due to the shorter days. Most spring-planted crops mature and are harvested during the fall months (Kansas Foundation for Agriculture in the Classroom, page 25). Plant growth and development is accomplished through many chemical and physiological processes which are governed by environmental factors such as light, water, temperature, oxygen and carbon dioxide. Growth of a new plant usually starts with seed germination which is the sexual form of propagation. Seed stratification requirements must be satisfied. Stratification provides the conditions for pre-germination physiological maturation which occurs under specific temperature and moisture regimes. In some instances, scarification is required on seeds with hard seed coats. Scarification is the softening of hard seed coats via freezing and thawing or other physical or chemical mechanisms. When stratification, scarification and light requirements have all been satisfied, water is absorbed and the cells of the embryo begin to enlarge. This seed enlargement usually ruptures the seed coat and allows the embryonic root or radicle, to emerge. Seed is germinated when the radicle and primary shoot are visible. The absorption of water activates many enzymes in the seed that cause the breakdown of carbohydrates to the simple sugar glucose, and the breakdown of protein to amino acids. Natural plant growth regulators, called phytohornones are also synthesized and translocated to sites of action. The embryo is completely dependent upon the stored food in the cotyledons, which are the first “leaves”, or food in the endosperm, which is a storage organ, until the first true green leaves emerge and begin active photosynthesis. Then, water and mineral uptake must actively occur through the roots. The seedling is self-sustainable at this stage providing proper environmental conditions exist (Bert T. Swanson and Jerry Cohen, PLANT GROWTH AND DEVELOPMENT, page 12-1). 2.3Light Emitting Diode 13 On the study of Strandberg, et al. (2012), Light Emitting Diode is a semiconductor device that emits visible light of a certain color, and is fundamentally different from conventional light sources such as incandescent, fluorescent, and gas-discharge lamps, in that an LED: uses no gas or filament, has no glass bulb, and no failure-prone moving parts. Their study had focused on the Basics of LED which its origin was cited. In 1962 the first red LED was developed by Nick Holonyak at G.E. Throughout the 60’s red LEDs were ued as small indicator lights on electronic devices. Green and yellow LEDs were introduced in the early 70’s, and were used in electronics, traffic signals, exit signs, and watches, etc. There were great minds that had contributed to LED in the history. On the present, The Department of Energy expects LED technology to become the preferred method of lighting in homes and offices by 2025. In addition, their stated presented ideas and statements which lead to the advantages of LEDs: Comparable in efficacy to CFLs, gaining on fluorescent tubes, and incandescent. Fixtures are directional, allowing for more efficient optics. Quality of White Light LEDs now comparable to CFLs, recent advances assure better consistency in color and CCT. Significantly longer ‘Useful’ life. Many more were presented on their study. As a whole, varied uses and advantages LEDs offer to the world. Thus, this is one the world’s great inventions. 14 CHAPTER 3 PROJECT DESCRIPTION This chapter discusses the procedural description, subject sample of the study, project environment, design concept, design description, and statistical analysis procedure. 3.1 Subject Sample of the Study In this study the researchers chose Monggo plant as the experimental subject. Actual Picture of Mung beans to be used 3.2 Environment of Experimentation The researchers will conduct the experimentation in an indoor and closed area where there will be no direct sunlight at Juarez’ residence in Brgy. Consuelo, Ilog, Negros Occidental. 3.3 Procedural Description This study will undergo procedures and these processes will take circle of the experimental subject, the usage of LED lights, and the days of experimentation. First there will be 10 Mung beans, the experimental subjects; 15 three colors of LED lights (blue, red & white). To conduct the experiment, the researchers will prepare the materials needed for the experimentation such as pot, soil, LEDs, and used boxes. To cover the plant from direct sunlight, the researchers will utilize an improvised cover made of used boxes. The boxes will be attached with LED lights. Each cover will only have one color of LED light per plant for the experimentation while the untreated subject which is cultivating naturally will be planted like the usual cultivation of plants. The time schedule for the switching on and off of the lights will be, 6am-7:00pm which serves as the time the LED lights will be switched on, while 7:01pm-5:59am will be scheduled as the time for switch off. All subjects will be scheduled with the same time of watering. This process will undergo to 21-31 days. To gather the data, the researchers will measure the plant growth of the Mung beans on the last day of process. Furthermore, the data that will be gathered will be tallied and will undergo statistical testing. 16 Design Concept Effect of Red, Blue and White LED Lights on Mung Beans’ Growth Interpretation of the Results of the Experiment Preparation of Materials Construction of Sunlight Cover Tallying of the Data Collected Planting of the Mung beans Measuring Plant Growth Conduct of Experimentation (21-31 days) Switching On ang Off Of LED lights Watering of Plants Monitoring Plant Condition 17 3.4 Design Description The diagram on the previous page was the design concept of the study. It illustrates the flow of the processes that this study will undergo. First is the construction of ideas which leads to the title of the study, Effect of Red, Blue and White LED Lights on Mung Beans’ Growth. Second is the preparation of the materials needed for the experimentation such as soil, pots/vases, LED lights. Third is the construction of sunlight cover for experimental subjects. The researchers will utilize a man-made cover from used boxes. Fourth is the production or planting of Mung beans and after that the conduct of the experiment will start. The conduct will span to 21-31 days. The next step is the measuring of plant growth. The researchers will use a measuring tool to measure the Monggo plant. Afterwards, the data collected will be tallied and will undergo statistical testing. On the last part of the process, the researchers will analyze the results of the study and will be interpreted. 3.5 Statistical Analysis Procedure The data that will be gathered in this study will use the Microsoft Excel for tallying of data. To get the result for the plant growth of Monggo in terms of height, number of leaves, and size of leaves on the untreated and treated experimental subject, the researchers will measure manually by the use of ruler with centimeters as the unit of measurement. 18 References Smestad A. (2017). The Effect of Light on Plant Growth. Retrieved: https://sciencing.com/the-effect-of-light-on-plant-growth-12201478.html Holman, R. (2020). Top 8 Benefits of LED Lights. Lifehack. Retrieved: https://www.lifehack.org/533944/top-8-benefits-using-led-lights Rehman M., Baloch S.U., Bao Y., Wang B., (2017). Light Emitting Diodes: Whether an Efficient Source of Light for Indoor Plants Retrieved: https://www.researchgate.net/publication/320220555_Lightemitting_diode s_whether_an_efficient_source_of_light_for_indoor_plants Leone J. (2017). LED Lights for Plant Growth. SCIENCING. https://sciencing.com/ledlights-plant-growth-5958172.html Mitchell, C.A, Both, A.J., Bourget, C.M., Burr, J.F., Kubota, C., Lopez, R.G., Morrow, R.C., & Runkle, E.S. (2012). LEDs: The future of greenhouse lighting. Chronica Horticulturae 907 179-184 Olle, M. & Virsile, A. (2013). The Effects of Light-emitting Diodes Lighting on greenhouse plants growth and quality. Retrieved: https://journal.fi/afs/article/view/7897 Snowden, M.C. (2015). Effects of Blue and Green Light on Plant Growth and Development Effects of Blue and Green Light on Plant Growth and Development at Low and High Photosynthetic Photon Flux. Retrieved: https://digitalcommons.usu.edu/cgi/viewcontent.cgi?article=5650&context =etd Saleem MH, Gohar F, Muhammaf IF2, Rehman O, Naseem N, Iqbal M, Tahir S, Yaqoob MT, Aslam R and Hassan A. (2019). Effect of Different Colors of Lights on Growth and Antioxidants Capacity in Rapeseed (Brassica Napus L.) Seedlings. Retrieved: 19 http://austinpublishinggroup.com/agriculture-cropsciences/download.php?file=fulltext/aacs-v4-id1045.pdf Dou, H., Niu, G., Gu, M., & Masabni, J. (2017). Effects of Light Quality on Growth and Phytonutrient Accumulation of Herbs under Controlled Environments. Retrieved: https://www.mdpi.com/2311-7524/3/2/36/pdf Bian, Z., Jiang, N., Grundy, S., & Lu, C. (2018). Uncovering LED light effects on plant growth: new angles and perspectives – LED light for improving plant growth, nutrition and energy-use efficiency. Retrieved: https://www.researchgate.net/publication/329459644_Uncovering_LED_li ght_effectson_plant_growth_New_angles_and_perspectives_LED_light_for_improvin g_plant_growth_nutrition_and_energy-use_efficiency Brukhin, V. & Morozova, N. (2011). Plant Growth and Development- Basic Knowledge and Current Views (page2). Retrieved: https://www.mmnpjournal.org/articles/mmnp/pdf/2011/02/mmnp201162p1.pdf Strandberg, E., LC & Robbins J., LC, MIES. (2012). The Basic of LEDs. Retrieved: http://www.lightingdesignlab.com/sites/default/files/pdf/Basics of LEDs.pdf Unit 3) Plant Growth and Development. Retrieved: https://ksagclassroom.org/wp-content/uploads/2018/05/Unit-3-PlantGrowth-and-Development.pdf Swanson, B. & Johen, J. Plant Growth and Development. Retrieved: https://cdn.ymaws.com/www.mnla.biz/resource/collection/6F4B6575A34D-4FEB-BC8A-68D04EAACF25/12.Plant Growth & Development.pdf 20