Articulation Agreement by Major Effective during the 2020-2021 Academic Year To: California State University, Long Beach From: East Los Angeles College 2020-2021 General Catalog, Semester 2020-2021 General Catalog, Semester Aerospace Engineering BACHELOR OF SCIENCE IN AEROSPACE ENGINEERING BACHELOR OF SCIENCE IN AEROSPACE ENGINEERING GENERAL INFORMATION 2020-21 IMPORTANT ADMISSIONS INFORMATION FOR FALL 2021 GENERAL INFORMATION 2020-21 ALL MAJORS AT CSU LONG BEACH ARE IMPACTED. As a result, all undergraduate majors will have major-specific admission requirements in the form of a list of major preparation coursework and GPA requirements. Please refer to the admissions website for these major-specific admission details. Follow the navigation of the site to find the correct path and year for your major. ADMISSION BASICS: Transfer students may only enter at the upper-division (junior) level. You are considered an upper-division transfer student if you will have completed 60 or more transferable semester units or 90 transferable quarter units by the end of the prior Spring term for Fall entrance or the prior Summer term for Spring entrance. As an upper-division transfer student, you must meet minimum CSU admission requirements to be considered for admission, as stated on the admissions website. The CSU GE (General Education) requirements in Written Communication, Oral Communication, Critical Thinking and Mathematics/Quantitative Reasoning must be completed with a grade of ‘C’ or better by the end of the prior Spring term for Fall admission or by the end of the prior Summer term for Spring admission. Major-specific course and gpa requirements for admission as referenced above must also be met by these same timelines. Follow the navigation of the site to find the correct path and year for your major. LOWER DIVISION MAJOR REQUIREMENTS: The courses listed below make up the lower division major requirements for this specific major and this catalog year. Students are encouraged to take as many of these courses prior to transfer as possible to promote timely completion of the degree at CSULB. BE AWARE: The courses on this list may not all be required for admission but are required for the award of the bachelor’s degree. Refer to the information and links provided above for major-specific admission requirements. The courses shown below constitute lower-division coursework required for this major for this catalog year. In addition, lower-division general education coursework is required (select General Education/Breadth on the main menu). This additional coursework can either be completed at a California Community College by achieving CSU-GE or IGETC certification (see a counselor for details), or the General Education/Breadth course list in effect at matriculation must be completed at CSULB. Be advised that lower-division course requirements are subject to change from year to year, and catalog rights (actual course requirements) will be established for the student effective with the catalog in effect as of the first term of matriculation at CSULB. Questions regarding this agreement may be directed to the CSULB Articulation Office at (562) 985-7171 or (562) 9851746 or at articulation@csulb.edu. GENERAL INFORMATION - DEGREE NOTES Degree Progress: Transfer students must complete the following requirements-within in oneNOTES calendar year of declaring the major: A grade of C or GENERAL INFORMATION DEGREE better must be achieved in MATH 123 (Calculus II) and PHYS 151 (Mechanics and Heat) within one calendar year after transfer to CSULB (if the equivalent was not taken before transfer). Questions can be directed to the College of Engineering Recruitment and Retention Center at (562) 9851800 or coe-admit@csulb.edu. Note: ENGR 101 and 102 are substituted for transfer students who have 3 units of CSU General Education Area E. A grade of 'C' or better must be achieved in all required courses listed below. LOWER DIVISION CORE REQUIREMENTS, TAKE ALL OF THE FOLLOWING COURSES: Minimum grade required: C or better LOWER DIVISION OF THEsection FOLLOWING COURSES: PleaseCORE refer toREQUIREMENTS, additional importantTAKE GeneralALL Information above C E 205 - Analytical Mechanics I (Statics) (3.00) Same-As: C E 205H Minimum grade required: C or better CHEM 111A - GENERAL CHEMISTRY (5.00) Minimum grade required: C or better ← ENG GEN 131 - Statics (3.00) ← CHEM 101 - General Chemistry I (5.00) ENGR 101 - Introduction to Engineering Profession (1.00) Same-As: ENGR 101H Please refer to additional important General Information section above Minimum grade required: C or better ENGR 102 - Academic Success Skills (1.00) Same-As: ENGR 102H Please refer to additional important General Information section above Minimum grade required: C or better MAE 101A - Introduction to Aerospace Engineering (1.00) Minimum grade required: C or better MAE 205 - Computer Methods in Mechanical and Aerospace Engineering (2.00) Minimum grade required: C or better ← ← ← ← ← ← ← ← MATH 122 - CALCULUS I (4.00) Minimum grade required: C or better MATH 123 - CALCULUS II (4.00) Minimum grade required: C or better MATH 224 - CALCULUS III (4.00) Minimum grade required: C or better PHYS 151 - MECHANICS AND HEAT (4.00) Minimum grade required: C or better ENG GEN 101 - Introduction to Science - Engineering and Technology (2.00) No Course Articulated No Course Articulated ENG GEN 122 - Programming and Problem-Solving in MATLAB (3.00) MATH 261 - Calculus I (5.00) MATH 262 - Calculus II (5.00) MATH 263 - Calculus III (5.00) PHYSICS 101 - Physics for Engineers and Scientists I (5.00) TAKE ONE OF THE FOLLOWING CHOICES: Please refer to additional important General Information section above TAKE ONE OF THE FOLLOWING CHOICES: ← PHYS 152 - ELECTRICITY AND MAGNETISM (4.00) Minimum grade required: C or better PHYSICS 102 - Physics for Engineers and Scientists II (5.00) --- Or --E E 210 - Electro-Magnetic Foundations in Electrical Engineering (3.00) Minimum grade required: C or better ← No Course Articulated --- And --E E 210L - Electro-Magnetic Foundations in Electrical Engineering Laboratory (1.00) Minimum grade required: C or better ← No Course Articulated TAKE ONE OF THE FOLLOWING CHOICES: Please refer to additional important General Information section above TAKE ONE OF THE FOLLOWING CHOICES: ← MAE 172 - Engineering Design Graphics (2.00) Minimum grade required: C or better EGD TEK 121 - 3-D Computer-Aided Design with SolidWorks (3.00) --- Or --MAE 172B - Engineering Design Graphics - Solidworks (2.00) Minimum grade required: C or better ← No Course Articulated --- Or --MAE 172C - Engineering Design Graphics - CATIA (2.00) Minimum grade required: C or better ← No Course Articulated END OF AGREEMENT
