.
SimSci®
PRO/II® 9.4
Silent Installation
Guide
October 2015
All terms mentionedin this documentation that are known to be trademarks or service marks have
been appropriately capitalized. Schneider Electric Software, LLC. cannot attest to the accuracy of
this information. Use of a term in this documentation should not be regarded as affecting the
validity of any trademark or service mark.
ActiveFactory, ArchestrA, ARPM, AssayCentral, Autonomous, Avantis, Avantis.PRO,
Connoisseur, CrudeManager, CrudeSuite, DATACON, DATAPREP, DT Analyst, DYNSIM,
DYNSIM Power, Esscor, EYESIM, Factelligence, FactorySuite, FactorySuite A², Foxboro,
Foxboro Evo, FSIM Plus, HEXTRAN, Hot Links, I/A Series, IMPACT, IMServ, InBatch,
InControl, Industrial Portal, IndustrialSQL Server, InFusion, INPLANT, InSQL, IntelaTrac,
InTouch, IPact, Invensys, Logic Validator, MBM, NETOPT, PIPEPHASE, PRO/II,
PROVISION, QI Analyst, ROMeo, SCADAlarm, SIM4ME, SimCentral, SimSci, SimSci-Esscor,
Skelta, Skelta BPM.NET, Skelta Sharepoint, Skelta Sharepoint Accelerator, Spiral Software,
SuiteVoyager, TACITE, Tactical Batch, The Simulator, TRISIM Plus, VISUAL FLARE,
VISUAL FLOW, VISUAL FLOW SUITE, VISUAL NETWORK, Visual Solutions,
VOYAGER, WindowMaker, WindowViewer, Wonderware, Wonderware InTouch, and ZI ZHI
are trademarks of Schneider Electric SE, its subsidiaries and affiliated companies.
© 2015 by Schneider Electric Software, LLC. All rights reserved.
No part of this documentation shall be reproduced, stored in a retrieval system, or transmitted by
any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Schneider Electric Software, LLC. No liability is assumed with respect to
the use of the information contained herein.
Although precaution has been taken in the preparation of this documentation, Schneider Electric
Software, LLC assumes no responsibility for errors or omissions. The information in this
documentation is subject to change without notice and does not represent a commitment on the
part of Schneider Electric Software, LLC. The software described in this documentation is
furnished under a license agreement. This software may be used or copied only in accordance
with the terms of such license agreement.
ArchestrA, Avantis, DYNSIM, EYESIM, Foxboro, Foxboro Evo, I/A Series, InBatch, InduSoft,
IntelaTrac, InTouch, PIPEPHASE, PRO/II, PROVISION, ROMeo, Schneider Electric, SIM4ME,
SimCentral, SimSci, Skelta, SmartGlance, Spiral Software, VISUAL FLARE, WindowMaker,
WindowViewer, and Wonderware are trademarks of Schneider Electric SE, its subsidiaries, and
affiliated companies. An extensive listing of Schneider Electric Software, LLC trademarks can be
found at: http://software.schneider-electric.com/legal/trademarks/. All other brands may be
trademarks of their respective owners.
Schneider Electric Software, LLC
26561 Rancho Parkway South
Lake Forest, CA 92630 U.S.A.
(949) 727-3200
http://software.schneider-electric.com/
PRO/II 9.4 Silent Installation Guide
This document lists the commands needed for installing PRO/II 9.4 silently.
Note:
1. PRO/II 9.4 silent install does not install its dependencies. Therefore, make sure that the dependencies
are installed before doing the silent installation of PRO/II 9.4.
2. Entry [PRO/II 9.4 setup folder] in below commands is the location of PRO/II 9.4 install folder where
setup.exe is located. Add double quotes if the full path contains space.
Silent installation of PRO/II 9.4 dependencies:
1. Install .NET 3.5 SP1 (Mandatory)
"[PRO/II 9.4 setup folder]\DotNet.3.5.SP1\netfx35sp1_x86.exe" /q /norestart
2. Install .NET 4.0 (Mandatory)
"[PRO/II 9.4 setup folder]\Microsoft .NET Framework 4 Setup\dotNetFx40_Full_x86_x64.exe" /q
/norestart
3. Install Microsoft Visual C++ 2005 Redistributable (Mandatory)
[PRO/II 9.4 setup folder]\Microsoft.2005.C++.Redistributable\vcredist_x86.exe /q
4. Install Microsoft Visual C++ 2008 SP1 Redistributable (Mandatory)
[PRO/II 9.4 setup folder]\Microsoft.2008.C++.Runtime\vcredist_x86-2008.exe /qn
5. Install Microsoft Visual C++ 2010 Redistributable (Mandatory)
"[PRO/II 9.4 setup folder]\Microsoft Visual C++ 2010 x86 Redistributable\vcredist_x86.exe" /q
6. Install Microsoft Visual C++ 2013 Redistributable (Mandatory)
"[PRO/II 9.4 setup folder]\Microsoft Visual C++ 2013 x86 Redistributable\vcredist_x86.exe" /q
7. Install VSTO2.0SE (Mandatory)
[PRO/II 9.4 setup folder]\ThirdPartySoftware\VSTO2.0SE\vstor2.0se.exe /q
8. Install VSTO4.0 32-bit (Conditional - This is needed for 32-bit Operating System)
[PRO/II 9.4 setup folder]\ThirdPartySoftware\VSTO4.0\vstor40_x86.exe /q
9. Install VSTO4.0 64-bit (Conditional - This is needed for 64-bit Operating System)
[PRO/II 9.4 setup folder]\ThirdPartySoftware\VSTO4.0\vstor40_x64.exe /q
10. Install O2007PIA (Conditional - This is needed only if you are using Office 2007)
[PRO/II 9.4 setup folder]\ThirdPartySoftware\O2007PIA\o2007pia.msi /qn
11. Install CAPE-OPEN (Mandatory)
[PRO/II 9.4 setup folder]\ThirdPartySoftware\CAPE-OPEN.msi /qn
12. Install USB driver 7.6.5 (Conditional - This is needed only if you are going to run PRO/II 9.4 using
USB for security)
"[PRO/II 9.4 setup folder]\ThirdPartySoftware\USB_Driver\Sentinel Protection Installer 7.6.5.exe"
/qn
13. Install OLI Chemistry Wizard (Optional)
[PRO/II 9.4 setup folder]\ThirdPartySoftware\OLI\OLI_Engine_in_PROII.9.2.5.exe /qn
14. Notepad++ (Mandatory)
[PRO/II 9.4 setup folder]\ThirdPartySoftware \NOTEPAD\npp.6.7.8.1.Installer.exe /s
15. RefPropAddonSetup (Optional)
[PRO/II 9.4 setup folder]\ThirdPartySoftware\NIST\RefPropAddonSetup.exe
16. Note: RefPropAddonSetup.exe will not support Silent install. It should be installed separately from
the above path.
Silent installation of PRO/II 9.4:
Install options:
1. INSTALLDIR - PRO/II 9.4 Install location (default: C:\Program files\SIMSCI). Use double quotes
around the path if it contains a space. Example: INSTALLDIR="C:\Program Files\SimSci"
2. SECURITY_TYPE - PRO/II 9.4 security type, such as USB, FLXNET11, FNP1111, TOKENNET or
TKN1111 (default: FNP1111). Example: SECURITY_TYPE=FNP1111
3. IPASSI_LICENSE_FILE - FLEXlm/TOKEN license manager (default: none). No need to specify
this if you are going to use USB for security.
Example: IPASSI_LICENSE_LICENSE_FILE=@FLEXlmServer
4. QUICK_LAUNCH_ICON – Option to create a quick launch icon (default: not create). To create the
icon, use QUICK_LAUNCH_ICON=1
5. DESKTOP_ICON – Option to create a desktop icon (default: create). To not create the icon, use
DESKTOP_ICON=""
6. ADDLOCAL – Option to specify what PRO/II 9.4 features to install. If this option is not used in the
PRO/II 9.4 silent install, the program will install CommonRequired, SIM4MEPortal, UAS and PDTS.
Features that can be specified include OPC_UAServer and Translator.
7. DEFAULTUOM – Option to set specify default UOM. Supported entries are: ENGLISH-SET1,
METRIC-SET1 and SI-SET1 (default: ENGLISH-SET1). Example: DEFAULTUOM=ENGLISHSET1
8. RESTOREAPPDATA – Option to restore existing customization in %APPDATA% folder (default:
not restore). To restore, use RESTOREAPPDATA=1
Note that unless ADDLOCAL=ALL is used, feature CommonRequired must always be included in the
list when using the ADDLOCAL option.
Examples: To install all features, use
ADDLOCAL=ALL or
ADDLOCAL= CommonRequired,SIM4MEPortal,UAS,PDTS,OPC_UAServer,Translator
Command example:
msiexec.exe /i [PRO/II 9.4setup folder]\PROII94.msi /qn SECURITY_TYPE=TOKENNET
INSTALLDIR="C:\Program Files\SimSci" DESKTOP_ICON="" QUICK_LAUNCH_ICON=1
IPASSI_LICENSE_FILE=@TokenNetServer ADDLOCAL=
CommonRequired,SIM4MEPortal,UAS,PDTS,Translator
The command above uses TOKENNET for security, installs PRO/II 9.4 to C:\Program Files\SimSci, does
not create the desktop icon, creates the quick launch icon, and uses machine TokenNetServer for the
TOKENNET security.
Silent installation of optional post-PRO/II 9.4 install applications:
1. Multi-Simulation Manager (MSM): MSM should be installed after the PRO/II 9.4 installation.
msiexec.exe "[PROII 9.4 Setup folder]\ThirdPartySoftware\MSM\Multi-Simulation Manager
1.0.2.msi" /qn
Invensys Systems, Inc.
26561 Rancho Parkway South
Lake Forest, CA 92630
United States of America
http://iom.invensys.com
Global Customer Support
Inside U.S.: 1-866-746-6477
Outside U.S.: 1-508-549-2424 or contact your
local Invensys Representative.
Email: Invensys.iom.support@Schneider-electric.com
Website: http://support.ips.invensys.com