Crosby® Shackles
SHACKLES
W i t h
P r o d u c t
W a r n i n g
a n d
A p p l i c a t i o n
I n f o r m a t i o n
SHACKLES
"There is No Equal"
The
G-209
Market Leader: Yesterday Today and Tomorrow
Shackles
DESIGN
The theoretical reserve capability of carbon shackles should
be as a minimum 5 to 1, and alloy shackles a minimum of 5 to
1*. Known as the DESIGN FACTOR, it is usually computed by
dividing the catalog ultimate load by the working load limit. The
ultimate load is the average load or force at which the product
fails or no longer supports the load. The working load limit is
the maximum mass or force which the product is authorized
to support in general service. The design factor is generally
expressed as a ratio such as 5 to 1. Also important to the
design of shackles is the selection of proper steel to support
fatigue, ductility and impact properties.
CLOSED DIE FORGED
The proper performance of premium shackles depends on
good manufacturing techniques that include proper forging and
accurate machining. Closed die forging of shackles assures
clear lettering, superior grain flo , and consistent dimensional
accuracy. A closed die forged bow allows for an increased
cross section that, when coupled with quench and tempering,
enhances strength and ductility. Closed die bow forgings
combined with close tolerance pin holes assures good fatigue
life. Close pin-to-hole tolerance has been proven to be critical
for good fatigue life, particularly with screw pin shackles.
QUENCHED AND TEMPERED
Quench and tempering assures the uniformity of
performance and maximizes the properties of the steel. This
means that each shackle meets its rated strength and has
required ductility, toughness, impact and fatigue properties.
The requirements of your job demand this reliability and
consistency. This quench and tempering process develops
a tough material that reduces the risk of brittle, catastrophic
failure. The shackle bow will deform if overloading occurs,
giving warning before ultimate failure.
THE COMPETITION
Ask: What is the Working Load Limit and design
factor for shackles?
Ask: Is deformation upon overloading a critical
consideration in their design?
Ask: Do they jeopardize other properties by
having hardness high in order to increase
working load or design factor?
The proper application of shackles requires that the
correct type and size of shackle be used. The shackle’s
working load limit, its size, a traceability code and the
manufacturer’s name should be clearly and boldly marked
in the bow. Traceability of the material chemistry and
properties is essential for total confidence in the product.
Material chemistry should be independently verified prior to
manufacturing.
Crosby carbon shackles have the highest design factor
(6 to 1) in the industry. All of Crosby’s design factors are
documented. Crosby purchases only special bar forging
quality steel with cleanliness and guaranteed harden ability.
All material chemistry is independently verified prior t
manufacturing. The design of Crosby shackles assures that
strength, ductility and fatigue properties are met.
THE COMPETITION
Ask: Are their shackles closed die forged with close
tolerance pin holes?
Ask: Do their shackles have good fatigue life?
Ask: Do their shackles have a fatigue life that meets
the new world standards?
Many forge bows utilize an open die forging
process which allows for inconsistent dimensional
accuracy and increased pin hole clearance, thus
jeopardizing the fatigue life of the shackle in actual
use.
Each shackle is closed die forged. Closed die forging produces
consistent dimensions. A closed die forged bow allows for an
increased cross section that, when coupled with quench and
tempering, enhances strength and ductility. Close tolerance
holes and concentric pins with good surface finishes are
provided by Crosby and are proven to provide improved fatigue
life in actual use. Crosby shackles are fatigue rated as well as
load rated. Close pin to hole tolerance has been proven to be
critical for good fatigue life, particularly with screw pin shackles.
®
THE COMPETITION
Ask: Are their bows and pins quenched and
tempered?
Ask: If not, are they willing to accept the increased
risk of inconsistency?
Ask: If not, why are they willing to accept inferior
impact, toughness, and product deformation?
Ask: Why do many manufacturers not recommend
non-heat-treated shackles for overhead lifting?
Ask: Why do some recommend Quench and
Tempering for alloy but not carbon grades?
Many normalize the shackle bows. As a result,
desired properties are not achieved. A few even
provide bows in an “as-forged” condition, resulting
in the possibility of brittle failure.
IDENTIFICATION AND
APPLICATION INFORMATION
G-2130
All Crosby shackle bows and pins are quenched and tempered,
which enhances their performance under cold temperatures and
adverse field conditions. Crosby s Quenched and Tempered
carbon shackles are recommended for all critical applications
including overhead lifting. Alloy shackles are recommended when
specific dimensional requirements dictate a size that require
higher working load limits. Crosby’s Quenched and Tempered
shackles provide the tensile strength, ductility, impact and fatigue
properties that are essential if they are to perform time after time
in adverse conditions. These properties assure that the inspection
criteria set forth by ANSI will effectively monitor the ability of the
shackles to continue in service.
THE COMPETITION
Ask: Do they have an active traceability system
used in manufacturing?
Ask: Is the material chemistry independently
verified?
Ask: What training support is provided?
Crosby forges “Crosby” or “CG”, the Working Load Limit, and
the Product Identification Code (PIC) into each bow and
“Crosby” or “CG”, and the Product Identification Code (PIC)
into each pin of its full line of screw pin, round pin, and bolt type
anchor and chain shackles. Seminars conducted by Crosby
provide training on the proper use of shackles. Crosby training
packets, supplied free to attendees of Crosby seminars,
provide training materials needed to
explain the proper use of shackles.
* G-2160 Wide Body Shackles are metric rated at 5 to 1. G-2140 Shackles, 200 ton and above, are rated at 4 to 1 in short tons.
74
Remember: “When buying Crosby, you’re buying more than product, you’re buying Quality.”
VALUE ADDED
• Charpy impact properties: Crosby’s Quenched and Tempered shackles have enhanced impact properties for greater
toughness at all temperatures. If requested at the time of order, Crosby can provide Charpy impact properties.
• Fatigue properties: Fatigue properties are available for 1/3 to 55 metric ton shackles. These Crosby shackles are fatigue
rated to 20,000 cycles at 1-1/2 times the Working Load Limit.
• Ductility properties: Typical ductility properties are available for all sizes upon special request.
• Hardness levels and material tensile strengths: Typical values are available for all sizes of shackles, and actual values can
be furnished if requested at the time of order.
• Proof Testing: If requested at the time of order, shackles can be proof tested with certificates.
• Mag Certification: If requested at the time of order, shackles can be Mag inspected with certificates.
• Certification: Certification to world class standards is available upon special request at the time of order; American Bureau of
Shipping, Lloyds Register of Shipping, Det Norske Veritas, American Petroleum Institute, RINA, Nuclear Regulatory
Commission, and several other worldwide standards.
• Applications: Round Pin Shackles can be used in tie down, towing, suspension or lifting applications where the load is
strictly applied in-line. Screw Pin Shackles can be used in any application where a round pin shackle is used. In
addition, screw pin shackles can be used for applications involving side-loading circumstances. Reduced working load limits
are required for side-loading applications. Bolt-Type Shackles can be used in any application where round pin or screw pin
shackles are used. In addition, they are recommended for permanent or long-term installations and where the load may slide
on the shackle pin causing the pin to rotate.
• Material analysis: Crosby can provide certified material (mill) analysis for each production lot, traceable by the Product
Identification Code (PIC). Crosby, through its own laboratory, verifies the analysis of each heat of steel. Crosby purchases only
special bar forging quality steel with specific cleanliness requirements and guaranteed hardenability.
• Field inspection: Written instructions for visual, magnaflux, and dye penetrant inspection of shackles are available from
Crosby. In addition, acceptance criteria and repair procedures for shackles are available.
• QUIC-CHECK®: Shackles incorporate two marking indicators forged into the shackle bow at 45° angles from vertical. These
are utilized to quickly check the approximate angle of a two-legged hitch or check the angle of a single leg hitch. If the load is
off vertical or side loaded a reduction in the working load limit of the shackle is required.
G-209
Screw pin anchor
shackles meet the
performance requirements
of Federal Specification
RR-C-271G, Type IVA, Grade
A, Class 2, except for those
provisions required
of the contractor.
G-210
Screw pin chain shackles
meet the performance
requirements of
Federal Specification
RR-C-271G, Type IVB,
Grade A, Class 2,
except for those
provisions required
of the contractor.
G-213
Round pin anchor
shackles meet the
performance
requirements of
Federal Specification
RR-C-271G, Type IVA,
Grade A, Class 1, except
for those provisions
required of the
contractor.
G-215
Round pin chain shackles
meet the performance
requirements of
Federal Specification
RR-C-271G, Type IVB,
Grade A, Class 1, except
for those provisions
required of the
contractor.
G-2130
Bolt-type anchor
shackles meet the
performance
requirements of
Federal Specification
RR-C-271G, Type IVA,
Grade A, Class 3,
except for those provisions
required of the contractor.
G-2150
Bolt-type chain
shackles meet the
performance requirements
of Federal Specification
RR-C-271G, Type IVB,
Grade A, Class 3,
except for those
provisions required
of the contractor.
SHACKLES
Crosby® Round Pin Shackles
•
•
•
•
•
•
•
•
Capacities 1/2 through 35 metric tons.
Forged - Quenched and Tempered, with alloy pins.
Working Load Limit permanently shown on every shackle.
Hot Dip galvanized or Self Colored.
Sizes 3/8 inch and below are mechanically galvanized.
Fatigue rated.
Shackles 25t and larger are RFID EQUIPPED.
Shackles can be furnished proof tested with certificates to des gnated standards,
such as ABS, DNV, Lloyds, or other certification. Charges for proof testing and
certification available when requested at the time of orde .
• Shackles are Quenched and Tempered and can meet DNV impact requirements
of 42 Joules (31 ft•Ibf) at -20° C (-4° F).
• Look for the Red Pin® . . . the mark of genuine Crosby quality.
G-213 / S-213
G-213 Round pin anchor
shackles meet the performance
requirements of Federal
Specification RR-C-271G, Type
IVA, Grade A, Class 1, except
for those provisions required of
the contractor. For additional
information, see page 452.
G-215 / S-215
G-215 Round pin chain shackles
meet the performance requirements
of Federal Specification RR-C-271G
Type IVB, Grade A, Class 1, except
for those provisions required of the
contractor. For additional information,
see page 476.
SEE APPLICATION INFORMATION
®
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-213 / S-213 Round Pin Anchor Shackles
Nominal
Size
(in)
1/4
5/16
3/8
7/16
1/2
5/8
3/4
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2
1-3/4
2
Working
Load
Limit
(t)*
1/2
3/4
1
1-1/2
2
3-1/4
4-3/4
6-1/2
8-1/2
9-1/2
12
13-1/2
17
25
35
Stock
No.
G-213
1018017
1018035
1018053
1018071
1018099
1018115
1018133
1018151
1018179
1018197
1018213
1018231
1018259
1018277
1018295
S-213
1018026
1018044
1018062
1018080
1018106
1018124
1018142
1018160
1018188
1018204
1018222
1018240
1018268
1018286
1018302
Weight
Each
(lb)
.13
.18
.29
.38
.71
1.50
2.32
3.49
5.00
6.97
9.75
13.25
17.25
29.46
45.75
Dimensions
(in)
A
.47
.53
.66
.75
.81
1.06
1.25
1.44
1.69
1.81
2.03
2.25
2.38
2.88
3.25
B
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.25
1.38
1.50
1.63
2.00
2.25
C
1.13
1.22
1.44
1.69
1.88
2.38
2.81
3.31
3.75
4.25
4.69
5.25
5.75
7.00
7.75
D
.25
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.29
1.42
1.54
1.84
2.08
E
.78
.84
1.03
1.16
1.31
1.69
2.00
2.28
2.69
2.91
3.25
3.63
3.88
5.00
5.75
F
.61
.75
.91
1.06
1.19
1.50
1.81
2.09
2.38
2.69
3.00
3.31
3.63
4.19
4.81
Tolerance
+/G
1.28
1.47
1.78
2.03
2.31
2.94
3.50
4.03
4.69
5.16
5.75
6.38
6.88
8.86
9.97
H
1.84
2.09
2.49
2.91
3.28
4.19
4.97
5.83
6.56
7.47
8.25
9.16
10.00
12.34
13.68
N
1.34
1.59
1.86
2.13
2.38
2.91
3.44
3.81
4.53
5.13
5.50
6.13
6.50
7.75
8.75
P
.25
.31
.38
.44
.50
.69
.81
.97
1.06
1.25
1.38
1.50
1.62
2.25
2.40
C
.06
.06
.13
.13
.13
.13
.25
.25
.25
.25
.25
.25
.25
.25
.25
A
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.13
.13
.13
.13
* NOTE: Maximum Proof Load is 2 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working Load Limit. DO NOT
SIDE LOAD ROUND PIN SHACKLES.
G-215 / S-215 Round Pin Chain Shackles
Nominal
Size
(in)
1/4
5/16
3/8
7/16
1/2
5/8
3/4
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2
1-3/4
2
Working
Load
Limit
(t)*
1/2
3/4
1
1-1/2
2
3-1/4
4-3/4
6-1/2
8-1/2
9-1/2
12
13-1/2
17
25
35
Stock
No.
G-215
1018810
1018838
1018856
1018874
1018892
1018918
1018936
1018954
1018972
1018990
1019016
1019034
1019052
1019070
1019098
S-215
1018829
1018847
1018865
1018883
1018909
1018927
1018945
1018963
1018981
1019007
1019025
1019043
1019061
1019089
1019105
Weight
Each
(lb)
A
.10
.47
.18
.53
.25
.66
.40
.75
.50
.81
1.21
1.06
2.00
1.25
3.28
1.44
4.75
1.69
6.30
1.81
9.00
2.03
12.00 2.25
16.15 2.38
29.96 2.88
43.25 3.25
Dimensions
(in)
B
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.25
1.38
1.50
1.63
2.00
2.25
C
.25
.31
.38
.44
.50
.63
.81
.97
1.00
1.25
1.38
1.50
1.62
2.12
2.36
D
.25
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.25
1.38
1.50
1.75
2.10
E
.97
1.15
1.42
1.63
1.81
2.32
2.75
3.20
3.69
4.07
4.53
5.01
5.38
6.38
7.25
F
.62
.75
.92
1.06
1.18
1.50
1.81
2.10
2.38
2.68
3.00
3.31
3.62
4.19
5.00
Tolerance
+/G
.91
1.07
1.28
1.48
1.66
2.04
2.40
2.86
3.24
3.61
3.97
4.43
4.87
5.82
6.82
K
1.59
1.91
2.31
2.67
3.03
3.76
4.53
5.33
5.94
6.78
7.50
8.28
9.05
10.97
12.74
N
1.34
1.63
1.86
2.13
2.38
2.91
3.44
3.81
4.53
5.13
5.50
6.13
6.50
7.75
8.75
G
.06
.06
.13
.13
.13
.13
.25
.25
.25
.25
.25
.25
.25
.25
.25
A
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.13
.13
.13
.13
.13
* NOTE: Maximum Proof Load is 2 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working Load Limit. DO NOT SIDE
LOAD ROUND PIN SHACKLES.
76
Copyright © 2019 The Crosby Group LLC All Rights Reserved
•
•
•
•
•
•
•
•
G-209 / S-209
G-209 Screw pin anchor shackles
meet the performance requirements
of Federal Specification RR-C-271G
Type IVA, Grade A, Class 2, except
for those provisions required of the
contractor. For additional information,
see page 452.
Capacities 1/3 thru 55 metric tons, grade 6.
Forged - Quenched and Tempered, with alloy pins.
Working Load Limit and grade “6” permanently shown on every shackle.
Hot Dip galvanized or self colored.
Sizes 3/8 inch and below are mechanically galvanized.
Fatigue rated.
Shackles 25t and larger are RFID EQUIPPED.
Shackles can be furnished proof tested with certificates to desi nated standards, such
as ABS, DNV, Lloyds, or other certification. Proof testing and certificati available when
requested at the time of order, charges will apply.
Approved for use at -40° C (-40° F) to 204° C (400° F).
All 209 and 210 shackles can meet charpy requirements of 42 Joules(31 ft•lbf) avg. at
-20° C (-4° F) upon special request.
Meets or exceeds all requirements of ASME B30.26.
•
•
•
•
Type Approval certification in accordance with ABS 2016 Steel Vessel Rules and
ABS Guide for Certification of Lifting Appliances available. Certificates available when
requested at time of order and may include additional charges.
Look for the Red Pin®. . . the mark of genuine Crosby quality.
•
Shackles
Crosby® Screw Pin Shackles
G-210 / S-210
G-210 Screw pin anchor shackles
meet the performance requirements
of Federal Specification RR-C-271G
Type IVB, Grade A, Class 2, except
for those provisions required of the
contractor. For additional information,
see page 452.
SEE APPLICATION INFORMATION
®
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-209 / S-209 Screw Pin Anchor Shackles
Nominal
Size
(in)
3/16
1/4
5/16
3/8
7/16
1/2
5/8
3/4
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2
1-3/4
2
2-1/2
Working
Load Limit
(t)*
1/3
1/2
3/4
1
1-1/2
2
3-1/4
4-3/4
6-1/2
8-1/2
9-1/2
12
13-1/2
17
25
35
55
Stock No.
G-209
1018357
1018375
1018393
1018419
1018437
1018455
1018473
1018491
1018516
1018534
1018552
1018570
1018598
1018614
1018632
1018650
1018678
S-209
–
1018384
1018400
1018428
1018446
1018464
1018482
1018507
1018525
1018543
1018561
1018589
1018605
1018623
1018641
1018669
1018687
Weight
Each
(lb)
.06
.10
.18
.31
.38
.72
1.37
2.35
3.62
5.03
7.41
9.50
13.53
17.20
27.78
45.00
85.75
A
.38
.47
.53
.66
.75
.81
1.06
1.25
1.44
1.69
1.81
2.03
2.25
2.38
2.88
3.25
4.13
B
.25
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.25
1.38
1.50
1.63
2.00
2.25
2.75
C
.88
1.13
1.22
1.44
1.69
1.88
2.38
2.81
3.31
3.75
4.25
4.69
5.25
5.75
7.00
7.75
10.50
D
.19
.25
.31
.38
.44
.50
.63
.75
.88
1.00
1.16
1.29
1.42
1.54
1.84
2.08
2.71
G-210 / S-210 Screw Pin Chain Shackles
Nominal Working
Size Load Limit
(in)
(t)*
1/4
1/2
5/16
3/4
3/8
1
7/16
1-1/2
1/2
2
5/8
3-1/4
3/4
4-3/4
7/8
6-1/2
1
8-1/2
1-1/8
9-1/2
1-1/4
12
1-3/8
13-1/2
1-1/2
17
1-3/4
25
2
35
2-1/2
55
Stock
No.
G-210
1019150
1019178
1019196
1019212
1019230
1019258
1019276
1019294
1019310
1019338
1019356
1019374
1019392
1019418
1019436
1019454
S-210
1019169
1019187
1019203
1019221
1019249
1019267
1019285
1019301
1019329
1019347
1019365
1019383
1019409
1019427
1019445
1019463
Weight
Each
(lb)
.11
.17
.28
.43
.59
1.25
2.63
3.16
4.75
6.75
9.06
11.63
15.95
26.75
42.31
71.75
Tolerance
+/-
Dimensions (in)
E
.60
.78
.84
1.03
1.16
1.31
1.69
2.00
2.28
2.69
2.91
3.25
3.63
3.88
5.00
5.75
7.25
F
.56
.61
.75
.91
1.06
1.19
1.50
1.81
2.09
2.38
2.69
3.00
3.31
3.63
4.19
4.81
5.69
G
.98
1.28
1.47
1.78
2.03
2.31
2.94
3.50
4.03
4.69
5.16
5.75
6.38
6.88
8.86
9.97
12.87
H
1.47
1.84
2.09
2.49
2.91
3.28
4.19
4.97
5.83
6.56
7.47
8.25
9.16
10.00
12.34
13.68
17.84
L
.16
.19
.22
.25
.31
.38
.44
.50
.50
.56
.63
.69
.75
.81
1.00
1.22
1.38
M
1.14
1.43
1.71
2.02
2.37
2.69
3.34
3.97
4.50
5.13
5.71
6.25
6.83
7.33
9.06
10.35
13.00
P
.19
.25
.31
.38
.44
.50
.69
.81
.97
1.06
1.25
1.38
1.50
1.62
2.25
2.40
3.13
Dimensions
(in)
A
.47
.53
.66
.75
.81
1.06
1.25
1.44
1.69
1.81
2.03
2.25
2.38
2.88
3.25
4.12
B
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.25
1.38
1.50
1.63
2.00
2.25
2.75
C
.25
.31
.38
.44
.50
.63
.81
.97
1.00
1.25
1.38
1.50
1.62
2.12
2.36
2.63
D
.25
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.25
1.38
1.50
1.75
2.10
2.63
E
.97
1.15
1.42
1.63
1.81
2.32
2.75
3.20
3.69
4.07
4.53
5.01
5.38
6.38
7.25
9.38
F
.62
.75
.92
1.06
1.18
1.50
1.81
2.10
2.38
2.69
3.00
3.31
3.62
4.19
5.00
5.68
C
.06
.06
.06
.13
.13
.13
.13
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
A
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.13
.13
.13
.13
.25
Tolerance
+/G
K
.97
1.59
1.07 1.91
1.28 2.31
1.48 2.67
1.66 3.03
2.04 3.76
2.40 4.53
2.86 5.33
3.24 5.94
3.61 6.78
3.97 7.50
4.43 8.28
4.87 9.05
5.78 10.97
6.77 12.74
8.07 14.85
L
.19
.22
.25
.31
.38
.44
.50
.50
.56
.63
.69
.75
.81
1.00
1.13
1.38
M
1.43
1.71
2.02
2.37
2.69
3.34
3.97
4.50
5.13
5.71
6.25
6.53
7.33
9.06
10.35
13.00
G
.06
.06
.13
.13
.13
.13
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
A
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.13
.13
.13
.13
.25
* NOTE: Maximum Proof Load is 2 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working Load Limit. For Working Load
Limit reduction due to side loading applications, see page 94.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
77
SHACKLES
Crosby® Alloy Screw Pin Shackles
•
•
•
•
•
•
G-209A
Screw pin anchor shackles meet
the performance requirements
of Federal Specification RR-C
271G, Type IVA, Grade B, Class
2, except for those provisions
required of the contractor. For
additional information, see
page 452.
Capacities 2 thru 21 metric tons. Meets performance requirements of Grade 8 shackles.
Forged Alloy Steel – Quenched and Tempered, with alloy pins.
Working Load Limit permanently shown on every shackle.
Hot Dip Galvanized.
Sizes 3/8 inch and below are mechanically galvanized.
Shackles can be furnished proof tested with certificates to des gnated standards, such as
ABS, DNV, Lloyds, or other certification. Charges for proof testing and certification availabl
when requested at the time of order.
• Approved for use at -40° C (-40° F) to 204° C (400° F).
• Meets or exceeds all requirements of ASME B30.26 including identification, ductilit ,
design factor, proof load and temperature requirements. Importantly, these shackles
meet other critical performance requirements including impact properties and material
traceability, not addressed by ASME B30.26.
SEE APPLICATION INFORMATION
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-209A Alloy Screw Pin Shackles
Nominal
Size
(in)
3/8
7/16
1/2
5/8
3/4
7/8
1
1-1/8
1-1/4
1-3/8
Working
Load
Limit
(t)*
2
2-2/3
3-1/3
5
7
9-1/2
12-1/2
15
18
21
G-209A
Stock No.
1017450
1017472
1017494
1017516
1017538
1017560
1017582
1017604
1017626
1017648
Weight
Each
(lb)
.31
.38
.63
1.38
2.35
3.61
5.32
7.25
9.88
13.25
A
.66
.75
.81
1.06
1.25
1.44
1.69
1.81
2.03
2.25
Dimensions
(in)
B
.44
.50
.63
.75
.88
1.00
1.13
1.25
1.38
1.50
C
1.44
1.69
1.88
2.38
2.81
3.31
3.75
4.25
4.69
5.25
D
.38
.44
.50
.63
.75
.88
1.00
1.16
1.29
1.42
E
1.03
1.16
1.31
1.69
2.00
2.28
2.69
2.91
3.25
3.63
F
.91
1.06
1.19
1.50
1.81
2.09
2.38
2.69
3.00
3.31
Tolerance
+/G
1.78
2.03
2.31
2.94
3.50
4.03
4.69
5.16
5.75
6.38
H
2.49
2.91
3.28
4.19
4.97
5.83
6.56
7.47
8.25
9.16
L
.25
.31
.38
.44
.50
.50
.56
.63
.69
.75
M
2.03
2.38
2.69
3.34
3.97
4.50
5.07
5.59
6.16
6.84
P
.38
.44
.50
.69
.81
.97
1.06
1.25
1.38
1.50
C
.13
.13
.13
.13
.25
.25
.25
.25
.25
.25
A
.06
.06
.06
.06
.06
.06
.06
.06
.06
.13
* Maximum Proof Load is 2 times the Working Load Limit (metric tons) and 2.2 times the Working Load Limit (short tons). Minimum Ultimate Strength is 4.5 times the Working Load Limit for metric tonnes,
and 5 times the Working Load Limit for short tons. For Working Load Limit reduction due to side loading applications, see page 94.
Capacities of 7, 12.5 and 18 metric tons.
Quenched and Tempered for maximum strength.
Forged Alloy Steel.
Available in galvanized and self colored finish
Individually proof tested and magnetic particle inspected. Crosby
certification available at time of orde .
• Meets or exceeds all requirements of ASME B30.26 including
identification, ductilit , design factor, proof load and temperature
requirements. Importantly, these shackles meet other critical
performance requirements including fatigue life, impact properties
and material traceability, not addressed by ASME B30.26.
• Look for the Red Pin® . . . the mark of genuine Crosby quality.
•
•
•
•
•
G-2169
G
CONVENTIONAL
SHACKLE
R
H
L
D
C
E
C
"WIDE BODY"
SHACKLE
B
M
SEE APPLICATION INFORMATION
S-2169
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-2169 / S-2169 Alloy Screw Pin “Wide Body” Shackles
Working Load
Limit
(t)*
7
12.5
18
J
P
K
G-2169
S-2169
Stock No. Stock No.
1021655
1021664
1021673
1021682
1021691
1021699
Weight Each
(lb)
3.5
8.8
13
B
+/.25
1.25
1.69
2.03
C
.69
.92
1.16
D
+/.02
.88
1.13
1.38
E
1.82
2.38
2.69
Dimensions
(in)
G
1.25
1.37
1.50
H
3.56
4.63
5.81
J
1.60
2.13
2.50
K
1.25
1.63
2.00
L
.50
.56
.69
M
3.97
5.13
6.25
P
4.10
5.51
6.76
R
5.87
7.63
9.38
* Ultimate Load is 5 times the Working Load Limit. Proof Load is 2 times the Working Load Limit.
78
Copyright © 2019 The Crosby Group LLC All Rights Reserved
Crosby® Bolt Type Shackles
G-2130 / S-2130
Bolt Type Anchor shackles with
thin head bolt - nut with cotter pin.
Meets the performance requirements
of Federal Specification RR-C
271G, Type IVA, Grade A, Class
3, except for those provisions
required of the contractor. For
additional information, see page 452.
•
•
•
•
•
•
•
•
•
•
•
Capacities 1/3 thru 150 metric tons, grade 6.
Working Load Limit and grade “6” permanently shown on every shackle.
Forged – Quenched and Tempered, with alloy bolts.
Hot Dip galvanized or self colored. (85, 120, and 150 metric ton shackles
are all hot dip galvanized bows and the bolts are Dimetcoted® and painted red)
Sizes 3/8 and below are mechanically galvanized.
Fatigue rated (1/3t - 55t).
Shackles 25t and larger are RFID EQUIPPED.
Approved for use at -40° C (-40° F) to 204° C (400° F).
Meets or exceeds all requirements of ASME B30.26.
Shackles 85 metric tons and larger are individually proof tested to 2.0 times the
working load limit.
Type Approval certification in accordance with ABS 2016 Steel Vessel Rules
ABS Guide for Certification of Lifting Appliances available. Certificates available
when requested at time of order and may include additional charges.
3.1 Certification as standard available for charpy and statisti al proof test from 3.25t
up to 25 tons to DNV2.7-1 and EN13889.
Crosby 3.25t through 25t G2130OC anchor shackles are type approved to DNV Certification
Notes 2.7-1- Offshore Containers. These Crosby shackles are statistical proof and impact
tested to 42 Joules (31 ft•lbf) min. avg. at -20° C (-4° F). The tests are conducted by Crosby
and 3.1 test certification is available upon request. Refer to page 87 for Crosby COLD
TUFF® shackles that meet the additional requirements of DNV rules for certification of lifting
applications - Loose Gear.
All other 2130 shackles can meet charpy requirements of 42 Joules (31 ft•lbf) avg at -20° C
(-4° F) when requested at time of order.
Look for the Red Pin® . . . the mark of genuine Crosby quality.
Shackles
•
•
•
•
SEE APPLICATION INFORMATION
®
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-2130 / S-2130 Bolt Type Anchor Shackles
Nominal Working
Size
Load Limit
(in)
(t)*
3/16
1/3 ‡
1/4
1/2
5/16
3/4
3/8
1
7/16
1-1/2
1/2
2
5/8
3-1/4
3/4
4-3/4
7/8
6-1/2
1
8-1/2
1-1/8
9-1/2
1-1/4
12
1-3/8
13-1/2
1-1/2
17
1-3/4
25
2
35
2-1/2
55
3
† 85
3-1/2
† 120 ‡
4
† 150 ‡
Dimensions
(in)
Stock
No.
G-2130
1019464
1019466
1019468
1019470
1019471
1019472
1019490
1019515
1019533
1019551
1019579
1019597
1019613
1019631
1019659
1019677
1019695
1019711
1019739
1019757
Weight
Each
S-2130 G-2130OC
(lb)
–
–
.06
–
–
.11
–
–
.22
–
–
.33
–
–
.49
1019481
–
.79
1019506 1262013
1.68
1019524 1262022
2.72
1019542 1262031
3.95
1019560 1262040
5.66
1019588 1262059
8.27
1019604 1262068
11.71
1019622 1262077
15.83
1019640 1262086
19.00
1019668 1262095
33.91
1019686
–
52.25
1019702
–
98.25
–
–
154.00
–
–
265.00
–
–
338.00
A
.38
.47
.53
.66
.75
.81
1.06
1.25
1.44
1.69
1.81
2.03
2.25
2.38
2.88
3.25
4.13
5.00
5.25
5.50
B
.25
.31
.38
.44
.50
.64
.77
.89
1.02
1.15
1.25
1.40
1.53
1.66
2.04
2.30
2.80
3.30
3.76
4.26
C
.88
1.13
1.22
1.44
1.69
1.88
2.38
2.81
3.31
3.75
4.25
4.69
5.25
5.75
7.00
7.75
10.50
13.00
14.63
14.50
D
.19
.25
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.29
1.42
1.53
1.84
2.08
2.71
3.12
3.62
4.00
E
.60
.78
.84
1.03
1.16
1.31
1.69
2.00
2.28
2.69
2.91
3.25
3.63
3.88
5.00
5.75
7.25
7.88
9.00
10.00
F
.56
.61
.75
.91
1.06
1.19
1.50
1.81
2.09
2.38
2.69
3.00
3.31
3.63
4.19
4.81
5.69
6.50
8.00
9.00
Tolerance
+/H
1.47
1.84
2.09
2.49
2.91
3.28
4.19
4.97
5.83
6.56
7.47
8.25
9.16
10.00
12.34
13.68
17.90
21.50
24.88
25.68
L
.98
1.28
1.47
1.78
2.03
2.31
2.94
3.50
4.03
4.69
5.16
5.75
6.38
6.88
8.80
10.15
12.75
14.62
17.02
18.00
M
1.29
1.56
1.82
2.17
2.51
2.80
3.56
4.15
4.82
5.39
5.90
6.69
7.21
7.73
9.68
10.81
13.58
15.13
17.00
17.75
N
.19
.25
.31
.38
.44
.50
.69
.81
.97
1.06
1.25
1.38
1.50
1.62
2.25
2.40
3.13
3.62
4.38
4.56
C
.06
.06
.06
.13
.13
.13
.13
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
A
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.13
.13
.13
.13
.25
.25
.25
.25
* NOTE: Maximum Proof Load is 2 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working Load Limit. For Working Load Limit reduction due to side loading applications, see page 94. † Individually Proof Tested with certification. ‡ Furnished in Anchor style only and furnished with eyebolts for handling.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
79
SHACKLES
Crosby® Bolt Type Shackles
•
•
•
•
G-2150 / S-2150
Bolt Type chain shackles
with thin hex head bolt - nut
with cotter pin. Meets the
performance requirements of
Federal Specification RR-C
271G, Type IVB, Grade A, Class
3,except for those provisions
required of the contractor.
For additional information,
see page 452.
•
•
•
•
•
•
•
Capacities 1/2 thru 85 metric tons, grade 6.
Working Load Limit and grade “6” permanently shown on every shackle.
Forged — Quenched and Tempered, with alloy pins.
Hot Dip galvanized or self colored. (85, 120, and 150-metric ton shackles are all
hot dip galvanized bows and the bolts are Dimetcoted® and painted red).
Sizes 3/8 inch and below are mechanically galvanized.
Fatigue rated (1/2t - 55t).
Shackles 25t and larger are RFID EQUIPPED.
Approved for use at -40° C (-40 degrees F) to 204° C (400° F).
Meets or exceeds all requirements of ASME B30.26.
Sizes 1/2 - 25t meet the performance requirements of EN13889:2003.
Shackles 55 metric tons and smaller can be furnished proof tested with certificate
to designated standards, such as ABS, DNV, Lloyds, or other certification whe
requested at time of order.
• Type Approval certification in accordance with ABS 2016 Steel Vessel Rules and
2016 ABS Guide for Certification of Lifting Appliance. Certificates available when
requested at time of order and may include additional charges.
• All 2150 shackles can meet charpy requirements of 42 Joules (31 ft•lbf) avg at -20° C
(-4° F) upon special request.
• Look for the Red Pin® . . . the mark of genuine Crosby quality.
SEE APPLICATION INFORMATION
®
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-2150 / S-2150 Bolt Type Chain Shackles
Nominal
Size
(in)
1/4
5/16
3/8
7/16
1/2
5/8
3/4
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2
1-3/4
2
2-1/2
3
Working
Load
Limit
(t)*
1/2
3/4
1
1-1/2
2
3-1/4
4-3/4
6-1/2
8-1/2
9-1/2
12
13-1/2
17
25
35
55
† 85
Stock
No.
G-2150
1019768
1019770
1019772
1019774
1019775
1019793
1019819
1019837
1019855
1019873
1019891
1019917
1019935
1019953
1019971
1019999
1020013
S-2150
–
–
–
–
1019784
1019800
1019828
1019846
1019864
1019882
1019908
1019926
1019944
1019962
1019980
1020004
–
Weight
Each
(lb)
.13
.23
.33
.49
.75
1.47
2.52
3.85
5.55
7.60
10.81
13.75
18.50
31.40
46.75
85.00
124.25
Dimensions
(in)
A
.47
.53
.66
.75
.81
1.06
1.25
1.44
1.69
1.81
2.03
2.25
2.38
2.88
3.25
4.12
5.00
B
.31
.38
.44
.50
.64
.77
.89
1.02
1.15
1.25
1.40
1.53
1.66
2.04
2.30
2.80
3.25
D
.25
.31
.38
.44
.50
.63
.75
.88
1.00
1.13
1.25
1.38
1.50
1.75
2.10
2.63
3.00
F
.62
.75
.92
1.06
1.18
1.50
1.81
2.10
2.38
2.68
3.00
3.31
3.62
4.19
5.00
5.68
6.50
G
.91
1.07
1.28
1.48
1.66
2.04
2.40
2.86
3.24
3.61
3.97
4.43
4.87
5.82
6.82
8.07
8.56
K
1.59
1.91
2.31
2.67
3.03
3.76
4.53
5.33
5.94
6.78
7.50
8.28
9.05
10.97
12.74
14.85
16.87
Tolerance
+/M
.97
1.15
1.42
1.63
1.81
2.32
2.75
3.20
3.69
4.07
4.53
5.01
5.38
6.38
7.25
9.38
11.00
P
1.56
1.82
2.17
2.51
2.80
3.56
4.15
4.82
5.39
5.90
6.69
7.21
7.73
9.33
10.41
13.58
15.13
R
.25
.31
.38
.44
.50
.63
.81
.97
1.00
1.25
1.38
1.50
1.62
2.12
2.36
2.63
3.50
G
.06
.06
.13
.13
.13
.13
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
.25
A
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.06
.13
.13
.13
.13
.25
.25
* NOTE: Maximum Proof Load is 2 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working Load Limit. For Working Load Limit reduction due to side loading applications, see page 94. † Individually Proof Tested with certification
80
Copyright © 2019 The Crosby Group LLC All Rights Reserved
Crosby® Bolt Type Shackles
Capacities 2 to 17 metric tons.
Meets or exceeds all requirements of Grade 8 shackles.
Working Load Limit permanently shown on every shackle.
Forged Alloy Steel – Quenched and Tempered, with bow and bolt.
Hot Dip galvanized.
Shackles can be RFID EQUIPPED.
Meets or exceeds all requirements of ASME B30.26 including identification,
ductility, design factor, proof load and temperature requirements.
Importantly, G-2130A meet other critical performance requirements
including impact properties and material traceability, not addressed by
ASME B30.26.
• Shackles can be furnished proof tested with certificates to designated
standards, such as ABS, DNV, Lloyds, or other certification when requested
at time of order.
• Type Approval and certification in accordance with DNV 2.7-1 O fshore
Containers.
• Shackles are Quenched and Tempered and meet DNV impact requirements
of 42 Joules (31 ft • Ibf) at -40° C (-40° F).
G-2130A
Bolt Type Anchor shackles with thin
head bolt – nut with cotter pin. Meets
the performance requirements of
Federal Specification R-C-271G,
Type IVA, Grade B, Class 3, except
for those provisions required of the
contractor. For additional information,
see page 452.
Shackles
•
•
•
•
•
•
•
SEE APPLICATION INFORMATION
®
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-2130A Alloy Bolt Bolt Type Shackles Grade 8
Nominal
Size
(in)
1/2
5/8
3/4
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2
Working
Load
Weight
Limit
G-2130A Each
(t)*
Stock No.
(lb)
2
1219472
.79
3-1/4
1219491
1.37
4-3/4
1219516
2.71
6-1/2
1219534
3.95
8-1/2
1219552
5.03
9-1/2
1219578
8.27
12
1219598
11.7
13-1/2
1219614
15.8
17
1219632
19.0
Dimensions
(in)
A
.81
1.06
1.25
1.44
1.69
1.81
2.03
2.25
2.38
B
.63
.75
.88
1.00
1.10
1.25
1.38
1.50
1.63
C
1.88
2.38
2.82
3.31
3.76
4.26
4.69
5.24
5.75
D
0.50
0.63
0.75
0.88
1.00
1.13
1.25
1.38
1.50
E
1.31
1.69
2.01
2.29
2.70
2.92
3.25
3.62
3.88
F
1.19
1.50
1.81
2.09
2.38
2.70
2.99
3.31
3.62
Tolerance
+/H
3.29
4.18
4.96
5.83
6.58
7.49
8.27
9.18
10.0
L
2.30
2.94
3.51
4.02
4.69
5.16
5.75
6.38
6.90
M
2.80
3.56
4.15
4.82
5.39
5.90
6.69
7.21
7.73
N
0.50
0.69
0.81
0.97
1.06
1.25
1.38
1.50
1.62
C
0.13
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
A
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.13
0.13
* NOTE: Maximum Proof Load is 2 times the Working Load Limit. Minimum Ultimate Strength is 8 times the Working Load Limit. For Working Load Limit
reduction due to side loading applications, see page 94.
Testing the Limits
In 2013, Sir Ranulph Fiennes and five colleague
set out to test the limits of human endurance and
achieve the feat of becoming the first individual
to cross the continent of Antarctica in winter. As
a proud partner in this endeavor, Crosby provided
its full range of COLD TUFF® products, which
are specifically manufactured to function i
extreme environments such as those encountered
throughout the expedition—including temperatures
as low as -90° C.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
81
SHACKLES
Crosby® Alloy Bolt Type Shackles
• Quenched and Tempered.
• Alloy bows, Alloy bolts.
• Forged Alloy Steel 2 thru 200 metric tons. Cast Alloy Steel 250 thru 400 metric tons.
Meets performance requirements of Grade 8 shackles.
• Working Load Limit is permanently shown on every shackle.
• 30, 40, 55, and 85 metric ton shackle bows are available galvanized or self colored
with bolts that are galvanized and painted red.
• Sizes 3/8 inch and below are mechanically galvanized.
G-2140 / S-2140
G-2140 meets the performance
requirements of Federal Specificatio
RR-C-271G, Type IVA, Grade B, Class
3, except for those provisions required
of the contractor. For additional
information, see page 452.
• 120, 150, 175 metric ton shackle bows are hot-dip galvanized; bolts are Dimetcoted
and painted red.
• 400 metric ton shackle bows are Dimetcoted; bolts are Dimetcoted and painted red.
• Sizes 1-1/2 and larger are RFID EQUIPPED.
• Approved for use at -40° C (-40° F) to 204° C (400° F).
• Shackles are Quenched and Tempered and can meet DNV impact requirements of
42 Joules (31 ft•lbf) at -20° C (-4° F).
• All sizes are individually proof tested to 2.0 times the Working Load Limit.
• Refer to page 87 for Crosby COLD TUFF® shackles that meet the additional requirements of DNV rules for
certification of lifting applications - Loose Gea .
• Shackles 200 metric tons and larger are provided as follows.
•
•
•
•
Serialized bolt and bow
Material certification (chemical
Magnetic particle inspected.
Certification must be requested at time of orde .
• Meets or exceeds all requirements of ASME B30.26 including identification, ductilit , design factor, proof load and
temperature requirements. 2140 shackles meet other critical performance requirements including impact properties
and material traceability, not addressed by ASME B30.26.
• Type Approval certification in accordance with ABS 2016 Steel Vessel Rules and 2016 ABS Guide for Certification of Liftin
Appliances. Certificates available when requested at time of order and ma include additional charges.
• Look for the Red Pin® . . . the mark of genuine Crosby quality.
SEE APPLICATION INFORMATION
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-2140 / S-2140 Crosby® Alloy Bolt Type Anchor Shackles
Nominal Working
Shackle
Load
Size
Limit
(in)
(t)*
G-2140
3/8
2
1021015
7/16
2 2/3
1021020
1/2
3 1/3
1021029
5/8
5
1021038
3/4
7
1021047
7/8
9 1/2
1021056
1
12 1/2
1021065
1 1/8
15
1021074
1 1/4
18
1021083
1 3/8
21
1021092
1-1/2
30
1021110
1-3/4
40
1021138
2
55
1021156
2-1/2
85
1021174
3
120
1021192
3-1/2
† 150
1021218
4
† 175
1021236
4-3/4
† 200
1021234
5
† 250
1021243
6
† 300
1021252
7**
† 400
1021478
Dimensions
(in)
Stock No.
Weight
Each
S-2140 G-2140OC
(lb)
–
0.33
–
0.49
–
0.79
–
1.68
–
2.72
–
3.95
–
5.66
–
8.27
–
11.7
–
15.8
1021129
1262407
18.8
1021147
1262416
33.8
1021165
1262425
49.9
1021183
1262434
103
1262443
162
1262452
327
1262461
318
–
–
461
–
–
608
–
–
797
–
1289
A
0.66
0.75
0.81
1.06
1.25
1.44
1.69
1.81
2.03
2.25
2.38
2.88
3.25
4.12
5.00
5.25
5.50
7.25
8.50
8.38
8.25
B
0.91
1.06
1.19
1.50
1.81
2.09
2.38
2.69
3.00
3.31
3.62
4.19
4.81
5.81
6.50
8.00
9.00
10.50
12.00
13.00
14.00
C
0.38
0.44
0.50
0.69
0.81
0.97
1.06
1.25
1.38
1.50
1.62
2.25
2.40
3.12
3.63
4.38
4.56
5.00
5.62
6.06
7.25
D +/.02
0.44
0.50
0.64
0.77
0.89
1.02
1.15
1.25
1.40
1.53
1.63
2.00
2.25
2.75
3.25
3.75
4.25
4.75
5.00
6.00
7.00
E
1.44
1.69
1.88
2.38
2.81
3.31
3.75
4.25
4.69
5.25
5.75
7.00
7.75
10.50
13.00
14.63
14.50
15.19
18.50
18.72
22.50
F
0.38
0.41
0.46
0.58
0.69
0.81
0.92
1.04
1.16
1.28
1.39
1.75
2.00
2.62
3.00
3.75
4.00
4.58
4.85
4.89
6.50
G
1.78
2.03
2.31
2.94
3.50
4.03
4.69
5.16
5.75
6.38
6.88
8.81
10.16
12.75
14.62
17.02
18.00
20.84
23.62
24.76
26.00
Tolerance
+/H
2.17
2.51
2.80
3.56
4.15
4.82
5.39
5.90
6.69
7.21
7.73
9.33
10.41
13.58
15.13
20.33
21.20
24.04
24.87
26.22
29.66
J
2.49
2.91
3.28
4.19
4.97
5.83
6.56
7.47
8.25
9.16
10.00
12.34
13.68
17.90
21.50
24.88
25.68
27.81
32.61
34.28
40.25
K
1.03
1.16
1.31
1.69
2.00
2.28
2.69
2.91
3.25
3.63
3.88
5.00
5.75
7.25
7.88
9.00
10.00
11.00
13.00
13.00
13.00
L
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.13
1.29
1.42
1.53
1.84
2.08
2.71
3.12
3.62
4.00
4.75
5.00
5.88
6.00
M
4.00
4.00
4.00
4.00
4.00
4.00
N
1.80
1.80
1.80
1.80
1.80
1.80
A
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.06
0.13
0.13
0.13
0.13
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
E
0.13
0.13
0.13
0.13
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
* Note: Maximum Proof Load is 2 times the Working Load Limit. Minimum Ultimate Load is 5 times the Working Load Limit on 2 thru 21 metric tons. For sizes 30 thru 175
metric tons, Minimum Ultimate Load is 5.4 times the Working Load Limit for 200 thru 400 metric tons, Minimum Ultimate Load is 4 times the Working Load Limit. ** Cast Alloy Steel. †
Furnished with Round Head Bolts with an handle for handling. For Working Load Limit reduction due to side loading applications, see page 94.
82
Copyright © 2019 The Crosby Group LLC All Rights Reserved
Crosby® Alloy Easy-Loc® Shackles
G-2140E
G-2140E meets the performance
requirements of Federal Specificatio
RR-C-271G, Type IVA, Grade B,
Class 3, except for those provisions
required of the contractor. For
additional information, see page 452.
G
K
L
C
E
J
Shackles
• Quenched and Tempered.
• Alloy bows, Alloy bolts.
• Forged Alloy Steel 200 thru 300 metric tons. Meets performance
requirements of Grade 8 shackles.
• Working Load Limit is permanently shown on every shackle.
• 200, 250, and 300 metric ton shackle bows are Dimetcoted®; pins are
Dimetcoted and painted red.
• All sizes are larger than 1-1/2 IN, RFID EQUIPPED.
• Approved for use at -40° C (-40° F) to 204° C (400° F).
• Shackles are Quenched and Tempered and can meet DNV impact
L
requirements of 42 Joules (31 ft•lbf) at -20° C (-4° F).
• All sizes are individually proof tested to 2.0 times the Working Load Limit.
• Refer to page 87 for Crosby COLD TUFF® shackles that meet the additional
requirements of DNV rules for certification of lifting applications - Loose Gea .
• Shackles are provided as follows:
• Serialized bolt and bow
• Material certification (chemical
• Magnetic particle inspected.
B
• Certification must be requested at time of orde .
• Meets or exceeds all requirements of ASME B30.26 including identification,
ductility, design factor, proof load and temperature requirements. Importantly,
these shackles meet other critical performance requirements including impact
properties and material traceability, not addressed by ASME B30.26.
• Type Approval certification in accordance with ABS 2016 Steel Vessel Rules
and 2016 ABS Guide for Certification of Lifting Appliances. Certificates
available when requested at time of order and may include additional charges.
• Look for the Red Pin® . . . the mark of genuine Crosby quality.
D
B
F
G
K
C
E
J
N
D
M
A
F
H
SEE APPLICATION INFORMATION
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-2140E Crosby® Alloy Easy-Loc Shackles
Nominal
Shackle
Size
(in)
4-3/4
5
6
Working
Load
Limit
(t)*
† 200
† 250
† 300
Stock No.
G-2140E
1021475
1021484
1021493
Weight
Each
(lb)
A
B
Dimensions
(in)
C
D
+/- .02
E
F
G
Tolerance
+/H
J
K
L
M
N
A
E
458
7.25 10.50 5.00
4.75
15.19 4.58 20.84 23.01 27.81 11.00 4.75 4.00 1.80 0.25 0.25
597
8.50 12.00 5.63
5.00
18.50 4.48 23.63 23.84 32.63 13.00 5.00 4.00 1.80 0.25 0.25
791
8.38 13.00 6.06
6.00
18.72 4.89 24.76 25.01 34.28 13.00 5.88 4.00 1.80 0.25 0.25
* Note: Maximum Proof Load is 2 times the Working Load Limit. For 200 thru 400 metric tons, Minimum Ultimate Load is 4 times the Working Load Limit. † Furnished with Round Head
Bolts with a handle for handling. For Working Load Limit reduction due to side loading applications, see page 94.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
83
A
H
SHACKLES
Crosby® Wide Body Shackles
•
•
•
•
•
•
•
•
•
•
G-2160 / S-2160
•
•
•
•
•
•
•
•
All sizes Quenched and Tempered for maximum strength.
Forged alloy steel from 7 thru 300 metric tons.
Cast alloy steel from 400 thru 1550 metric tons.
Proof tested as follows:
• 7 thru 75 metric tons and 200 thru 300 metric tons: 2 x WLL.
• 125 metric tons: 1.6 x WLL.
• 400 metric tons and higher: 1.33 x WLL.
All ratings are in metric tons, embossed on side of bow.
G-2160, (7 thru 55t), are Hot Dip Galvanized and pins are painted red.
G-2160, (75t and larger), bows are furnished Dimetcoted, and pins are
Dimetcoted, then painted red.
S-2160 bows and pins are painted red.
Shackles, 30t and larger, are RFID EQUIPPED.
Can be used to connect Synthetic Web Slings, Synthetic Round Slings or Wire
Rope Slings.
Increase in shackle bow radius provides minimum 58% gain in sling bearing
surface and eliminates need for a thimble.
Increases usable sling strength minimum of 15% and greatly improves life of wire
rope slings.
Approved for use at -40° C (-40° F) to 204° C (400° F).
Bow and bolt are certified to meet charpy impact testing of 42 Joules (31 f •lbf)
min. avg. at -20° C (-4° F).
All 2160 shackles are individually proof tested and magnetic particle inspected. Crosby certification available at time
of order.
Shackles requiring ABS, Lloyds and other certifications are available upon special request and must be specified a
time of order.
Type approved and certification to DNV Rules for Certification o Lifting Appliances, and are produced in accordance with
DNV MSA requirements. Databook is provided that includes required documents.
• Serialization / Identification
• Material Testing (Physical / Chemical / Charpy)
• Proof Testing
Look for the Red Pin® . . . the mark of genuine Crosby quality.
SEE APPLICATION INFORMATION
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-2160 / S-2160 Crosby® “Wide Body” Shackles
Working
Load
Limit
(t)*
7
12.5
18
30
40
55
75
125
200
300
400
500
600
700
800
900
1000
1250
1550
Stock
No.
G-2160
1021256
1021265
1021274
1021283
1021285
1021287
1022101
1022110
1022118
1022127
1021334
1021343
1021352
1021361
1021254
1021389
1021370
1021272
1021281
S-2160
1021548
1021557
1021566
1021575
1021584
1021593
–
–
–
–
–
–
–
–
–
–
–
–
–
Weight
Each
(lb)
4.0
8.8
14.9
26.5
46.0
68.0
112
193
420
805
1143
1439
2132
2579
3025
3678
4079
5320
8302
Dimensions
(in)
A
4.14
5.38
6.69
7.69
9.28
10.36
15.04
17.70
19.35
22.61
30.27
33.35
36.02
38.91
41.66
43.73
45.98
49.86
54.89
B
+/- .25
1.25
1.69
2.03
2.37
2.88
3.25
4.13
5.12
5.91
7.38
8.66
9.84
10.83
11.81
12.80
13.78
14.96
16.99
18.31
C
.69
.92
1.16
1.38
1.69
2.00
2.12
2.66
2.94
3.84
5.16
5.73
6.23
6.59
7.30
7.78
8.33
9.16
11.10
D
+/- .02
.88
1.13
1.38
1.63
2.00
2.25
2.75
3.15
4.12
5.25
6.30
7.09
7.87
8.46
9.06
9.84
10.63
11.81
12.60
E
1.82
2.38
2.69
3.50
4.00
4.63
5.34
6.50
8.41
10.50
12.56
13.39
15.50
17.03
17.69
18.81
20.00
22.56
24.25
G
1.25
1.37
1.50
2.50
1.75
2.00
3.75
3.75
5.25
6.13
7.99
8.09
13.00
8.87
9.76
13.00
10.26
13.92
12.52
H
3.56
4.63
5.81
6.94
8.06
9.36
11.53
14.37
18.91
23.63
22.64
24.81
27.56
28.94
29.53
29.82
29.92
36.61
42.32
J
1.60
2.13
2.50
3.13
3.75
4.50
5.00
5.91
8.56
10.38
12.60
13.39
14.57
15.75
16.54
18.81
18.11
20.87
22.82
K
1.25
1.63
2.00
2.50
3.00
3.50
3.64
4.33
5.42
6.31
7.28
8.86
9.74
10.63
10.92
11.52
12.11
12.70
13.29
M
–
–
–
–
–
–
4.00
4.00
4.00
4.00
4.00
4.00
5.75
5.75
5.75
5.75
5.75
–
–
N
–
–
–
–
–
–
1.80
1.80
1.80
1.80
1.80
1.80
2.25
2.25
2.25
2.25
2.25
–
–
P
4.10
5.51
6.76
8.50
10.62
12.26
12.28
15.47
20.47
24.00
27.17
31.10
34.05
37.01
38.39
40.35
42.32
46.26
51.81
R
5.87
7.63
9.38
11.38
13.62
15.63
18.66
23.00
30.44
37.66
38.78
42.72
47.24
50.18
52.09
54.59
55.31
65.35
74.63
Effective Body
Diameter
2.1
2.4
2.8
4.1
3.6
4.3
6.3
6.8
9.5
11.4
14.3
14.8
20.3
16.6
18.0
22.4
19.3
24.4
23.9
*Note: Maximum Proof Load is 2 times the Working Load Limit on 75 thru 300 metric tons (except for 125 metric tons which is proof tested to 1.6 times the Working Load Limit). Minimum
Ultimate Load is 5 times the Working Load Limit on 75 thru 300 metric tons. Maximum Proof Load is 1.33 times the Working Load Limit on 400 thru 1550 metric tons. Minimum Ultimate
Load is 4.5 times the Working Load Limit on 400 thru 1550 metric tons.
84
Copyright © 2019 The Crosby Group LLC All Rights Reserved
Crosby® Wide Body Shackles
• All sizes Quenched and Tempered for maximum strength.
• Forged alloy steel from 75 through 300 metric tons.
• Proof tested as follows:
• 7-75 metric tons and 200-300 metric tons: 2 x WLL.
• 125 metric tons: 1.6 x WLL.
• All ratings are in metric tons, embossed on side of bow.
• G-2160E, (75t and larger), bows are furnished Dimetcoted, and pins are
Dimetcoted, then painted red.
• Shackles are RFID EQUIPPED.
• Can be used to connect HIGH STRENGTH Synthetic Web Slings, HIGH
STRENGTH Synthetic Round Slings or Wire Rope Slings.
• Increase in shackle bow radius provides minimum 58% gain in sling bearing
J
surface and eliminates need for a thimble.
G
• Increases usable sling strength minimum of 15% and greatly improves life of
wire rope slings.
• Approved for use at -40° C (-40° F) to 204 degrees C (400° F).
• Bow and bolt are certified to meet charpy impact testing of 42 Joules
(31 ft•lbf) min. avg. at -20° C (-4 degrees F).
• All 2160E shackles are individually proof tested and magnetic particle
inspected. Crosby certification available at time of orde .
• Shackles requiring ABS, Lloyds and other certifications are available upon
special request and must be specified at time of orde .
E
• Shackles have DNV Type Approval to Rules for Certification of Liftin
Appliances, and are produced in accordance with DNV MSA requirements.
Databook is provided that includes required documents.
• Serialization / Identification
• Material Testing (Physical / Chemical / Charpy)
• Proof Testing
• Look for the Red Pin® . . . the mark of genuine Crosby quality.
G-2160E
J
P
R
H
D
R
A
K
H
N
M
D
B
C
A
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
Working
Load
Limit
(t)*
75
125
200
300
Stock
No.
G-2160E
1021500
1021509
1021518
1021527
Weight
Each
(lb)
S-2160E
–
110
–
190
–
408
–
787
B
A
+/- .25
15.04 4.13
17.70 5.12
19.35 5.91
22.61 7.38
D
C +/- .02
2.39 2.75
3.10 3.15
3.39 4.12
4.30 5.25
E
5.34
6.50
8.41
10.50
G
3.75
3.75
5.25
6.13
Dimensions
(in)
H
11.54
14.37
18.91
23.63
J
5.00
5.91
8.56
10.38
K
3.64
4.33
5.42
6.31
M
4.00
4.00
4.00
4.00
N
1.80
1.80
1.80
1.80
P
12.64
15.47
20.27
23.93
R
18.66
23.00
30.44
37.51
Effective Body
Diameter
6.3
6.8
9.5
11.4
*Note: Maximum Proof Load is 2 times the Working Load Limit on 75 thru 300 metric tons (except for 125 metric tons which is proof tested to 1.6 times the Working Load Limit). Minimum
Ultimate Load is 5 times the Working Load Limit on 75 thru 300 metric tons.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
C
B
E
P
SEE APPLICATION INFORMATION
G-2160E Crosby® Easy-Loc “Wide Body” Shackles
K
Shackles
G
85
SHACKLES
Crosby® Grommet Shackles
•
•
•
•
•
•
•
•
•
G-2170
Grommet
Shackle
•
•
•
•
•
Scan our QR Code
with your smart
device to visit the
online flye .
•
All sizes Quenched and Tempered for maximum strength.
JJ
All sizes cast alloy steel.
All ratings are in metric tons, embossed on side of bow.
G-2170 bows are furnished Dimetcoted and pins are Dimetcoted, then
painted red.
All sizes are RFID EQUIPPED in bow and pin.
Designed for use with single or double large diameter grommets.
Extra large sling contact area improves efficiency of the grommet sling
Shackles utilize new Easy-Loc bolt system
Large machined flat on ears that can be drilled and tapped for adapting
other accessories.
EE
Increases usable sling strength minimum of 60% and greatly improves life
of grommet slings.
Bow and bolt are certified to meet charpy impact testing of 42 Joules
(31 ft • lbf) min. avg. at -20° C (-4° F).
All 2170 shackles are individually proof tested and magnetic particle inspected.
Shackles requiring ABS, Lloyds, and other certifications are available upon
special request and must be specified at time of orde .
All 2170 shackles can meet requirements of DNV Rules for Certification of
Lifting Appliances upon special request and must be specified t time of
order.
• Serialization / Identificatio
• Material Testing (Physical / Chemical / Charpy)
• Proof Testing
Look for the Red Pin®….the mark of genuine Crosby quality.
PP
R
R
H
H
N
N
M
M
D
B
B
C
C
A
A
JJ
PP
R
R
D
EE
B
B
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
Stock
Working
No.
Load
Limit
(t)*
G-2170
75
1023147
125
1023156
200
1023174
300
1023183
500
1022119
Weight
Each
(lb)
115
179
374
692
1671
A
15.04
17.01
19.35
22.61
29.95
B
+/- .25
4.13
5.13
5.91
7.38
9.84
C
2.39
2.75
3.39
4.30
6.00
Dimensions
(in)
D
+/- .02
2.75
3.15
4.12
5.25
7.09
E
5.50
6.72
9.00
11.13
13.75
H
7.77
9.31
11.64
15.20
19.72
J
7.50
9.00
12.90
15.50
20.00
M
4.00
4.00
4.00
4.00
4.00
N
1.80
1.80
1.80
1.80
1.80
P
9.38
11.00
13.63
17.00
23.00
R
16.20
19.25
25.01
31.82
41.44
Effective Body
Diameter
11.25
13.50
18.45
22.75
30.00
* Note: Maximum Proof Load is 2 times the Working Load Limit on 75 thru 300 metric tons. Minimum Ultimate Load is 5 times the Working Load Limit on 75 thru 300 metric tons.Maximum
Proof Load is 1.33 times the Working Load Limit on 500 metric tons. Minimum Ultimate Load is 4.5 times the Working Load Limit on 500 metric tons.
86
C
C
A
A
SEE APPLICATION INFORMATION
G-2170 Crosby® Grommet Shackles
H
H
Copyright © 2017
2019 The Crosby Group LLC All Rights Reserved
Crosby® COLD TUFF® Shackles
G-2130CT / G-2140CT
Shackles
• Forged - Quenched and Tempered, with alloy bolt.
• G-2130CT - Carbon Steel
• G-2140CT - Alloy Steel
• Working Load Limit permanently shown on every shackle.
• Individually serialized with certification
• Fatigue Rated (G-2130CT only).
• Shackles 25t and larger are RFID EQUIPPED.
• All sizes are individually proof tested to 2.0 times the Working Load Limit.
• Finish is inorganic zinc primer.
• Bow and bolt are certified to meet charpy impact testing of 42 Joules (31 f •lbf)
min. avg. at -20° C (-4° F).
• Individually mag inspected with certification
• Type Approval and certification in accordance with DNV 2.7-1 O fshore
Containers, and Rules for Certification of Lifting Appliances, DNV-OS-E101 and
are produced in accordance with DNV MSA requirements, including required
documents.
• DNV certified minimum design temperature -4° . May be used at -50°F (-45° C)
in non DNV applications.
• Refer to page 167 for COLD TUFF® Master Links and Master Link assemblies.
SEE APPLICATION INFORMATION
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
Crosby® G-2130CT COLD TUFF®
Nominal
Shackle
Size
(in)
3/4
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2
1-3/4
Working
Load
Limit
(t)*
4-3/4
6-1/2
8-1/2
9-1/2
12
13-1/2
17
25
G-2130CT
Stock No.
1260568
1260577
1260586
1260595
1260604
1260613
1260622
1260633
Weight
Each
(lb)
2.72
3.87
5.66
8.26
11.71
15.1
20.8
33.9
Dimensions
(in)
A
1.25
1.44
1.69
1.81
2.03
2.25
2.38
2.88
B
.88
1.00
1.13
1.25
1.38
1.50
1.63
2.00
C
2.81
3.31
3.75
4.25
4.69
5.25
5.75
7.00
D
.75
.88
1.03
1.13
1.29
1.38
1.54
1.84
E
2.00
2.28
2.69
2.91
3.25
3.63
3.88
5.00
F
1.81
2.09
2.38
2.69
3.00
3.31
3.63
4.19
Tolerance
+/H
4.97
5.83
6.56
7.47
8.25
9.16
10.00
12.34
L
3.50
4.03
4.69
5.16
5.75
6.38
6.88
8.86
N
.81
.97
1.06
1.25
1.38
1.50
1.62
2.25
P
4.25
4.71
5.38
5.90
6.63
7.21
7.66
9.19
A
.06
.06
.06
.06
.06
.13
.13
.13
C
.25
.25
.25
.25
.25
.25
.25
.25
Bolt Type Anchor shackle with thin head bolt - nut with cotter pin. Meets the performance requirements of Federal Specification RR-C-271 Type IVA, Grade A, Class 3, except for those provisions
required of the contractor. For additional information, see page 466.
* NOTE: Maximum Proof Load is 2 times the Working Load Limit. 4-3/4t - 25t, Minimum Ultimate Load is 5.4 times the Working Load Limit. For Working Load Limit
reduction due to side loading applications, see page 94.
Crosby® G-2140CT COLD TUFF® Shackles
Nominal
Shackle
Size
(in)
1-1/2
1-3/4
2
2-1/2
3
3-1/2
4
4-3/4
5
Working
Load
Limit
(t)*
30
40
55
85
120
† 150
† 175
† 200
† 250
G-2140CT
Stock No.
1260801
1260812
1260823
1260834
1260843
1260852
1260861
1260870
1260889
Weight
Each
(lb)
20.8
33.9
52.0
96.0
178.0
265.0
338.0
450.0
600.0
A
2.38
2.88
3.25
4.12
5.00
5.25
5.50
7.25
8.50
B
1.63
2.00
2.25
2.75
3.25
3.75
4.25
4.75
5.00
Dimensions
(in)
C
5.75
7.00
7.75
10.50
13.00
14.63
14.5
15.63
20.00
D
1.54
1.84
2.08
2.72
3.11
3.62
4.10
4.50
4.50
E
3.88
5.00
5.75
7.25
7.88
9.00
10.00
11.00
13.00
F
3.62
4.19
4.81
5.69
6.50
8.00
9.00
10.50
12.00
Tolerance
+/H
10.00
12.34
13.68
17.84
21.50
24.62
25.69
29.25
35.00
L
6.88
8.81
10.16
12.87
14.36
16.50
18.42
21.00
24.50
N
1.62
2.25
2.40
3.12
3.63
4.12
4.56
6.00
6.50
P
7.73
9.33
10.41
13.58
15.13
17.62
20.37
21.21
22.68
A
.13
.13
.13
.25
.25
.25
.25
.25
.25
C
.25
.25
.25
.25
.25
.25
.25
.25
.25
Bolt Type Anchor shackle with thin head bolt - nut with cotter pin. Meets the performance requirements of Federal Specification RR-C-271 Type IVA, Grade B, Class 3, except for those provisions
required of the contractor. For additional information, see page 466.
* NOTE: Maximum Proof Load is 2 times the Working Load Limit. 30t - 175t, Minimum Ultimate Load is 5.4 times the Working Load Limit. 200t and larger, Minimum
Ultimate Load is 4 times the Working Load Limit. † Furnished with Round Head Bolts with welded handle. For Working Load Limit reduction due to side loading
applications, see page 94.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
87
SHACKLES
Shackle Bolt Securement
MADE EASY
The Patent Pending Easy-Loc V2™
shackle bolt securement system
will change the way you make your
next critical lift. It’s shackle bolt
securement made as easy as 1,2,3.
Both shackle and pin
are RFID equipped
Wide opening ergonomic
grip provides easy access
for all hand sizes
316 stainless steel design
resists corrosion
1
Open collar
2
3
Push collar onto bolt
Close collar
The new Easy-Loc V2TM can
be retrofi ted on all original
Crosby Easy-Loc® Shackles
No cotter pin or
tools required
• No cotter pins or tools required, reducing
install/release time up to 90%
• Meets all industry standards
• Up to 60% lighter than conventional nut
and cotter pin design
Made in the U.S.A.
88
Contact your local authorized Crosby distributorCopyright
or visit
at The
thecrosbygroup.com
© 2019
Crosby Group LLC All Rights Reserved
Crosby® Specialty Shackles
• Sizes: 3/8” through 3/4”
• Capacities: 1 through 4-3/4 metric tonnes.
Shackles
• Forged - Quenched and Tempered, with alloy pins.
• Working Load Limit permanently shown on every shackle.
• Flat black baked on powder coat finish
• Fatigue Rated.
• Industry leading 6 to 1 design factor.
S-209T
THEATRICAL
SHACKLE
• Screw pin anchor shackles meet the performance requirement of Federal
Specification RR-C-271G, Type IVA, Grade A, Class 2, except for those
provisions required of the contractor.
• Meets the performance requirements of EN 13889.
• Meets or exceeds all requirements of ASME B30.26 including identification,
ductility, design factor, proof load and temperature requirements. Importantly,
these shackles meet other critical performance requirements including fatigue
life, impact properties and material traceability, not addressed by ASME B30.26.
SEE APPLICATION INFORMATION
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
S-209T Theatrical Shackles
Nominal
Size
(in)
3/8
7/16
1/2
5/8
3/4
Working
Load
Limit
(t)*
1
1-1/2
2
3-1/4
4-3/4
S-209T
Stock No.
1018706
1018724
1018742
1018760
1018778
Weight
Each
(lb)
.31
.38
.72
1.37
2.35
Dimensions
(in)
A
.66
.75
.81
1.06
1.25
B
.44
.50
.63
.75
.88
C
1.44
1.69
.188
2.38
2.81
D
.38
.40
.50
.63
.75
E
1.03
1.16
1.31
1.69
2.00
F
.91
1.06
1.19
1.50
1.81
Tolerance
+/G
1.78
2.03
2.31
2.94
3.50
H
2.49
2.91
3.28
4.19
4.97
L
.25
.31
.38
.44
.50
M
2.02
2.37
2.69
3.34
3.97
P
.38
.44
.50
.69
.81
C
.13
.13
.13
.13
.25
A
.06
.06
.06
.06
.06
* Minimum Ultimate Load is 6 times the Working Load Limit. Maximum Proof Load is 2.0 times the Working Load Limit.
S-209T...The “Crosby”
When you’re looking for the top-named shackle used for
theatrical and stage rigging applications, ask for a
“Crosby”— the name synonymous with quality, safety
and heavy lifting. The S-209T shackle is enhanced
with a flat black baked-on power coat finish th
causes the shackle to blend in with stage surroundings.
This guarantees “behind-the-scene” strength and
dependability without detracting the eye from on-stage
action.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
89
SHACKLES
Crosby ® Release & Retrieve ROV Shackle
G-2110
Release & Retrieve
ROV Shackle with
Non - Thread Bolt
G-2100
Release & Retrieve
ROV Shackle with
QUIC-Thread Bolt
•
•
•
•
•
•
•
•
•
•
Forged alloy bow with an industry best 6 to 1 performance
design factor.
Patent pending captured bolt can withstand over 2,000 lbs.
(907 kg) of pull-out force.
Galvanized bow with an API RP 17H color compliant coating.
Galvanized alloy bolt (Non-Threaded) (G-2110)
On average, QUIC-Thread bolt requires only 3.5 rotations for full
engagement (G-2100)
Raised pad for serialization.
API RP 17H compliant 316 stainless steel handles available in
T, D, F, and Eye models (sold separately)
Built in eyelets for optional tether points.
Monkey fist(s) included
Capacities from 9-1/2t through 85t.
• Forged Steel, Quenched & Tempered, with alloy pins.
• Working Load Limit permanently shown on every shackle.
• QUIC-CHECK® deformation and angle indicators forged
on the bow.
SEE APPLICATION INFORMATION
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-2100 ROV Release & Retrieve Shackle ─ QUIC-Threaded
Working Load Limit
(t)*
9.5
12
17
25
35
55
85
Stock
No.
2038739
2038762
2038785
2038614
2038808
2038831
2038877
Weight Each
(lb)
11.4
13.8
23.7
38.6
51.2
108
157
A
1.81
2.03
2.38
2.88
3.25
4.12
5.00
B
2.91
3.25
3.88
5.00
5.75
7.25
7.88
C
4.25
4.69
5.75
7.00
7.74
10.49
12.98
D
1.25
1.38
1.63
2.00
2.28
2.78
3.28
Dimensions (in)
E
F
G
7.33
1.16 2.68
7.75
1.29 3.00
8.54
1.53 3.62
9.54 1.84 4.20
10.41 2.08 4.82
12.61 2.72 5.81
14.23 3.12 6.50
H
0.38
0.38
0.50
0.50
0.50
0.50
0.50
J
0.31
0.31
0.31
0.38
0.38
0.38
0.50
K
11.54
12.25
13.74
15.48
16.97
20.74
23.61
L
4.21
4.50
5.20
5.94
6.56
8.13
9.38
N
4.97
4.97
6.28
6.94
6.94
8.53
8.53
H
0.38
0.38
0.50
0.50
0.50
0.50
0.50
J
0.31
0.31
0.31
0.38
0.38
0.38
0.50
K
11.54
12.25
13.74
15.48
16.97
20.74
23.61
L
4.21
4.50
5.20
5.94
6.56
8.13
9.38
N
4.97
4.97
6.28
6.94
6.94
8.53
8.53
*Minimum Ultimate Load is 6 times the Working Load Limit in metric tons. *Note: Maximum Proof Loads are 2xWLL in metric tons.
G-2110 ROV Release & Retrieve Shackle ─ Non-Threaded
Working Load Limit
(t)*
9.5
12
17
25
35
55
85
Stock
No.
2038740
2038763
2038786
2038621
2038809
2038832
2038878
Weight Each
(lb)
11.4
13.8
23.7
38.6
51.2
108
157
A
1.81
2.03
2.38
2.88
3.25
4.12
5.00
B
2.91
3.25
3.88
5.00
5.75
7.25
7.88
C
4.25
4.69
5.75
7.00
7.74
10.49
12.98
D
1.25
1.38
1.63
2.00
2.28
2.78
3.28
Dimensions (in)
E
F
G
7.33
1.16 2.68
7.75
1.29 3.00
8.54
1.53 3.62
9.54 1.84 4.20
10.41 2.08 4.82
12.61 2.72 5.81
14.23 3.12 6.50
*Minimum Ultimate Load is 6 times the Working Load Limit in metric tons. *Note: Maximum Proof Loads are 2xWLL in metric tons.
90
Copyright © 2019 The Crosby Group LLC All Rights Reserved
Eye
E
B
C
E
D
H
B
ROV Handles Options and Configurations
F
C
H
A
F
A
G
J
D
J
D
E
D
B
E
F
B
C
H
F
Eye
E
C
H
F
B
C
A
H
G
A
J
G
D
D
“F” Handle
“D” Handle
A
E
D
“Eye” Handle
D
J
B
F
H
B
T
E
J
C
H
H
F
F
A
D
B
C
F
G
E
B
C
H
F
A
“T” Handle
Eye
E
C
Shackles
F
G
D
A
A
D
G
D
J
T
Eye
•
•
•
•
F
E
B
New Interchangeable
handles for ROV shackle bolts.
C
For use with G-2100
and G-2110 ROV shackles only.
H
F
Handles
are
stainless
steel and Painted fluorescent orange.
A
D
J
“D” and “F” handle kits available containing handle, retainingA bolts,
and individual packet of Loctite for easy installation.
E
B
F Handles are RFID equipped.
C
E
B
E
B
A
•
G
C
H
C
H
F
NOTE: ROV Hooks available
on page 130 and 131.
F
D
G
D
H
G-42100H ROV Handles
T
F
A
E
Handle
Style
D
StockG
No.
1021324
WeightDEach
(lb)
4.5
A
0.28
B
0.24
C
0.29
D
2.75
F
TT
1021315
1021306
1021333
5.0
2.4
2.1
0.28
0.28
0.28
0.24
0.24
0.24
0.29A
0.29
0.29
2.75
G
2.75
2.75
E
Eye
B
C
B
Dimensions (in)
F
C
EH
0.75
F
1.75
G
5.04
H
9.9
J
0.75
K
-
0.75
0.75
0.75
1.56
D
0.75
0.75
5.5
3.82
-
12.29
6.18
3.69
0.86
0.75
-
H
F
A
G
D
G-209R
ROV SHACKLE
•
•
•
•
•
•
•
Capacities from 6-1/2t through 55t.
Forged Steel, Quenched & Tempered, with alloy pins.
Working Load Limit permanently shown on every shackle.
Fatigue rated.
QUIC-CHECK® deformation and angle indicators forged on the bow.
All ROV shackle bows are galvanized, then painted fluorescent yellow.
Look for the Red Pin® . . . the mark of genuine Crosby quality.
SEE APPLICATION INFORMATION
On Page 92 of the General Catalog
Para Español: www.thecrosbygroup.com
G-209R Subsea Shackles
Working Load Limit
(t)*
6-1/2
8-1/2
9-1/2
12
13-1/2
17
25
35
55
G-209R
Stock No.
1020872
1020902
1020932
1020952
1020972
1020992
1021102
1021125
1021158
Weight Each
(lb)
3.62
5.03
7.41
9.50
13.53
17.20
27.78
45.00
85.75
Dimensions (in)
A +/- .25
1.44
1.69
1.81
2.03
2.25
2.38
2.88
3.25
4.13
B
1.00
1.13
1.25
1.38
1.50
1.63
2.00
2.25
2.75
C
3.31
3.75
4.25
4.69
5.25
5.75
7.00
7.75
10.50
H
5.83
6.56
7.47
8.25
9.16
10.00
12.34
13.68
17.84
L
4.03
4.69
5.16
5.75
6.38
6.88
8.86
9.97
12.87
O
1.18
1.18
2.28
2.28
2.36
2.36
2.16
2.60
2.76
P
2.28
2.40
3.27
3.31
3.58
3.66
4.49
5.12
5.63
S
.65
.73
.75
.89
.91
1.18
1.14
1.18
1.50
T
.39
.39
.47
.47
.59
.59
.69
.79
.98
* Minimum Ultimate Load is 5 times the Working Load Limit. Maximum Proof Load is 2.0 times the Working Load Limit.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
91
SHACKLES
Application Information
Round Pin
Shackles
G/S-213
Screw Pin
Shackles
G/S-215
G/S-209
S-209T
G-209A
Round Pin Shackles can be used in tie down,
towing, suspension or lifting applications where
the load is strictly applied in-line. Round pin
shackles should never be used in rigging
applications to gather multiple sling legs, or
where side loading conditions may occur.
G/S-210
Bolt-Type
Shackles
S-253
G-2169
Screw Pin Shackles are used in Pick and Place* applications. For
permanent or long-term installations, Crosby recommends the use of bolt
type shackles.
If you choose to disregard Crosby’s recommendation, the screw pin shall
be secured from rotation or loosening (Page 93).
G/S-2130
G/S-2140
G/S-2150
G/S-2160
Screw pin shackles can be used for applications involving side-loading
circumstances. Reduced working load limits are required for side-loading
applications. While in service, do not allow the screw pin to be rotated by
a live line, such as a choker application.
* Pick and Place application: Pick (move) a load and place as required.
Tighten screw pin before each pick.
Bolt-Type Shackles can be used in any application where round pin
or screw pin shackles are used. In addition, they are recommended for
permanent or long term installations and where the load may slide on the
shackle pin causing the pin to rotate. The bolt-type shackle’s secondary
securement system, utilizing a nut and cotter, eliminates the requirement to
tighten pin before each lift or movement of load.
All Crosby Shackles, with the exception of 2160, 2169, 2170, 252 and 253 styles
incorporate markings forged into the product that address an easy to use
QUIC-CHECK® feature. Angle indicators are forged into the shackle bow at
45 degree** angles from vertical. These are utilized on screw pin and bolt type
shackles to quickly check the approximate angle of a two-legged hitch, or quickly
check the angle of a single leg hitch when the shackle pin is secured and the pull of the load is off vertical (side
loaded), thus requiring a reduction in the working load limit of the shackle.
** Round Pin Shackles utilize the 45 degree QUIC-CHECK® indicators to ensure load is applied strictly in-line.
92
G-2130
Copyright © 2019 The Crosby Group LLC All Rights Reserved
Application Information
RIGGING PRACTICE SHACKLES
Shackles
Screw pin shall be fully engaged. If designed for a cotter pin, it shall be used and maintained.
Applied load should be centered in the bow to prevent side loading. Multiple sling legs should not be
applied to the pin. If side loaded, the rated load shall be reduced according to Table 1 on pages 94.
Screw Pin Shackles Pin Security
MOUSE SCREW PIN WHEN USED IN LONG-TERM
OR HIGH-VIBRATION APPLICATIONS.
Mouse or Mousing (screw pin shackle) is a secondary securement method
used to secure screw pin from rotation or loosening. Annealed iron wire is
looped through hole in collar of pin and around adjacent leg of shackle
body with wire ends securely twisted together.
Shackles
ROUND PIN
Do not side load, do
not use as a collector
ring, always use
cotter pin.
SCREW PIN
Use when picking
and placing a load,
tighten pin prior
to each lift.
Connection of Slings to Shackles
BOLT-TYPE
Use in permanent
or long-term
installations, always
use nut and cotter.
Shackle must be
large enough to avoid
pinching of synthetic
slings.
Diameter of shackle
must be greater than
wire rope diameter if
no thimble in eye.
Bolt-Type Shackles
Use Bolt-Type Shackle
when a permanent or longterm connection.
Use a screw pin shackle
when it will be a temporary
connection.
Copyright © 2019 The Crosby Group LLC All Rights Reserved
ALTHOUGH POINT LOADING IS
ACCEPTABLE, A PAD EYE WIDTH
OF 50%-80% OR MORE OF SHACKLE
SPREAD IS BEST PRACTICE
93
SHACKLES
Application Information
Point Loading of Crosby Shackles
®
It has been determined that all Crosby ® shackles can be point-to-point loaded to the Working Load Limit without bending of the pin/bolt. This loading can be
bow-to-bow, bow-to-pin, or pin-to-pin (if there is not interference between the diameter of the shackle ears). However, caution should be given to maintain the
load at the center of the span by spacers so the load will not slide over to one side, and overload that ear. See “Off Center Loading Of Crosby ® Screw Pin & Bolt
Type Shackles – 3/16” to 3” Sizes”
Angular Loading Of Crosby Screw Pin & Bolt Type Shackles
®
Crosby ® has made representative tests with smaller size shackles with the load applied at 90 degrees to the normal plane of loading (ie. in-line). The test results
indicated that in order to maintain a proof load of 2 times the Working Load Limit (2 x WLL), the Working Load Limit should be reduced to 50% (ie. one-half the
catalog working load rating). DO NOT SIDE LOAD G/S-213 OR G/S-215 ROUND PIN SHACKLES. Calculations based on the above test indicates the Working
Load Limit should be reduced as shown below for loads applied at various angles to the normal plane of loading:
SIDE LOADED RATING REDUCTION
TABLE FOR 3/16” - 3” (120 METRIC TONS)
Angle loads must
be applied in the
plane of the bow.
Table 1
Side Loading Reduction Chart for Screw Pin and Bolt Type Shackles Only+
Angle of Side Load
from Vertical In-Line of Shackle
45
DEGREES
90
DEGREES
Adjusted
Working Load Limit
0° - 10° In-Line*
0% of Rated Working Load Limit
11°- 20° from In-Line*
15% of Rated Working Load Limit
21°- 30° from In-Line*
25% of Rated Working Load Limit
31°- 45° from In-Line*
30% of Rated Working Load Limit
46°- 55° from In-Line*
40% of Rated Working Load Limit
56°- 70° from In-Line*
45% of Rated Working Load Limit
71°- 90° from In-Line*
50% of Rated Working Load Limit
+ In-Line load is applied perpendicular to pin. * DO NOT SIDE LOAD ROUND PIN SHACKLE.
Table 1
SHACKLE SIZE GREATER THAN 3”
ANGLE FROM IN-LINE (DEGREES) REDUCTION IN WLL
0° - 5° In-Line*
0% of Rated Working Load Limit
6°- 10° from In-Line*
15% of Rated Working Load Limit
>10° from In-Line*
ANALYSIS REQ’D.
For shackles larger than 125 metric tons, where the angle of the side load is greater than 5 degrees,
contact Crosby Engineering.
INCLUDED ANGLE - SHACKLES
Never exceed 120° included angle. Use Bolt Type and Screw Pin
Shackles ONLY.
Shackles symmetrically loaded with two leg slings having a maximum
included angle of 120° can be utilized to full Working Load Limit.
For shackles larger than 125 metric tons, the maximum included angle
is 90 degrees for full working load limit. Contact Crosby Engineering if
included angle is greater than 90 degrees.
94
Copyright © 2019 The Crosby Group LLC All Rights Reserved