DON MARIANO MARCOS MEMORIAL STATE UNIVERSITY
MID LA UNION CAMPUS
San Fernando City, La Union
COURSE GUIDE
SUBJECT
:
COURSE NO.
:
INSTRUCTOR/PROFESSOR :
CONTACT DETAILS
:
Advanced Industrial Arts
II
THE 243
Rodrigo G. Bustillos Jr.
0919 009 5157
rbustillos@dmmmsu.edu.ph
INTRODUCTION
This course deals with the study of practical electricity, practical electronics,
practical mechanical works and practical refrigeration and air conditioning.
Emphasis is on the application of technology, in the processing of materials, its
operation and fabrication of useful articles/tools/equipment/gadgets and other
related electro-mechanical works.
COURSE OBJECTIVES
At the end of the course, the students will be able to:
1. Demonstrate ability to apply knowledge and skills of materials, tools,
equipment, processes, and products of production, distribution and
conservation of materials in the following areas:
a. Electrical;
b. Electronics;
c. Mechanical; and
d. Refrigeration and air-conditioning.
2. Develop desirable attitudes and values which will contribute to the economic
growth of the production industry.
COURSE CONTENT
This course is composed of two units and six modules with 56 lessons. It
is structured as follows:
Unit 1:
ELECTRONICS AND ELECTRICAL TECHNOLOGY
Module 1. APPLICATIONS OF ELECTRICAL TECHNOLOGY
Lesson 1.
Fundamentals of electricity
Lesson 2
Electrical tools, measuring instruments safety rules and
work habits in the job
Lesson 3
Mensuration and Calculation
Lesson 4
Interpret Technical Drawing
Lesson 5
Roughing-in and wiring activities for three-phase
distribution system for power, lighting and motor
control panel
Lesson 6
Installation of data measurement and control system on
electrical and auxiliary equipment
Lesson 7
Install, assemble, test and maintain motor control
system
Lesson 8
Proper Care and Maintenance of Tools and Equipment
Module 2. APPLICATIONS OF ELECTRONICS TECHNOLOGY
Lesson 1.
Introduction to electronics
Lesson 2.
Mensuration and calculation
Lesson 3.
Interpret technical drawing
Lesson 4.
Test electronic components
Lesson 5.
Assemble Electronic Products
Lesson 6
Service consumer electronic products and systems
Lesson 7
Service industrial electronic modules, products and
Systems
Lesson 8
Proper Care and Maintenance of Tools and Equipment
Unit II ELECTRO-MECHANICAL PROCESSES
Module 3. CASTING OF METALS
Lesson 1.
Introduction to casting
Lesson 2
Safety practices in casting
Lesson 3
Sand casting
Lesson 4
Investment casting
Lesson 5` Die casting
Lesson 6
Low pressure casting
Lesson 7
Centrifugal casting
Lesson 8
Gravity die casting
Lesson 9
Vacuum die casting
Lesson 10 Squeeze die casting
Lesson 11 Casting equipment care and maintenance
Module 4. MACHINING OF METALS
Lesson 1.
Introduction to machining
Lesson 2.
Tools, equipment and safety practices
Lesson 3.
Interpret working drawing and sketches
Lesson 4.
Select and cut workshop materials
Lesson 5.
Perform shop computation
Lesson 6
Measure work piece
Lesson 7
Perform bench work
Lesson 8
Turn work piece
Lesson 9
Mill work piece
Lesson 10 Grind work piece
Lesson 11 Shape work piece
Lesson 12 Repair work piece
Lesson 13 Equipment care and maintenance
Module 5. JOINING OF METALS
Lesson 1.
Introduction to joining
Lesson 2.
Safety practices
Lesson 3.
Perform industry calculation
Lesson 4.
Hand tools
Lesson 5.
Set-up welding equipment
Lesson 6
Lesson 7
Lesson 8
Fit up weld materials
Repair welds
Equipment care and maintenance
Module 6. APPLICATIONS OF REFRIGERATION AND AIR-CONDITIONING
Lesson 1.
Introduction to refrigeration and air-conditioning
Lesson 2.
Matter, laws of refrigeration and thermodynamics
Lesson 3.
Perform mensuration and calculations
Lesson 4.
Bench works
Lesson 5.
Electrical works
Lesson 6
Maintain tools and equipment
Lesson 7
Housekeeping practices
Lesson 8
Installation of refrigeration and air-conditioning systems
MODULE / TOPIC
This course deals with the study of practical
electricity,
practical
electronics,
practical
mechanical works and practical refrigeration and
air conditioning. Emphasis is on the application of
technology, in the processing of materials, its
operation
and
fabrication
of
useful
articles/tools/equipment/gadgets
and
other
related electro-mechanical works.
MODULE 1 Application of Electrical Technology
Learning Objectives:
STUDY
PERIOD
EXPECTATIONS
Introduce
yourselves through
the Course Site.
August
29, 2020
Present Course
Content and
Requirements
When you have completed this module, you will be able
to:
1. Apply the different electrical safety rules
Respond to the
2. Maintain electrical tools and equipment;
September questions/ queries
3. Learn the fundamentals of electrical wiring;
5, 2020
raised in the class.
4. Perform roughing-in activities for electrical
distribution system;
5. Install electrical wiring devices using the
different wiring methods;
6. Install electrical protection system for lighting
and grounding;
7 Prepare and interpret electrical plans.
Module 1.
APPLICATIONS OF ELECTRICAL
TECHNOLOGY
Lesson 1
Fundamentals of electricity
September Presentation of
Lesson 2
Electrical tools, measuring
5, 2020
report and class
instruments safety rules and work
discussion
habits in the job
Lesson 3
Mensuration and Calculation
Lesson 4
Interpret Technical Drawing
Lesson 5
Lesson 6
Lesson 7
Lesson 8
Roughing-in and wiring
activities for three-phase
distribution system for power,
lighting and motor control
panel
Installation of data measurement and
control system on electrical and
auxiliary equipment
Install, assemble, test and maintain
motor control system
Proper Care and Maintenance of
Tools and Equipment
September Presentation of
12, 2020
report and active
class discussion
MODULE 2 Application of Electronics Technology
When you have completed this module, you will be
able to:
1. Familiarize with the different tools, materials
and equipment used in electricity and electronics
works.
2. Familiarize with the different Electronic
Symbols.
Presentation of
3. Solve problems involving Ohm’s Law.
report and class
4. Familiarize with the different types and
discussion
functions of passive components such as resistor, September
capacitor, inductor and transformer.
19, 2020
5. Recognize the operation and characteristics of
Respond to the
the passive components when connected series,
questions/ queries
parallel, or series-parallel circuits.
raised in the class.
Module 2.
Lesson
Lesson
Lesson
Lesson
1.
2.
3.
4.
Lesson 5.
Lesson 6
Lesson 7
Lesson 8
APPLICATIONS OF ELECTRONICS
TECHNOLOGY
Introduction to electronics
Mensuration and calculation
Interpret technical drawing
Test electronic components
Assemble Electronic Products
Service consumer electronic products
and systems
Service industrial electronic
modules, products and Systems
Proper Care and Maintenance of
Tools and Equipment
Respond to the
questions/ queries
September raised in the class.
26, 2020
Interactive class
discussion via
online classes.
MODULE 3 ELECTRO-MECHANICAL PROCESSES
When you have completed this module, you will be
able to:
1. To understand the outline of the casting process
2. To understand the difference between a pattern and
a casting
3. To understand how to select the pattern material
4. To know the various types of pattern and their
application
Module 3.
Lesson 1.
Lesson 2
Lesson 3
Lesson 4
Lesson 5`
Lesson 6
CASTING OF METALS
Introduction to casting
Safety practices in casting
Sand casting
Investment casting
Die casting
Low pressure casting
Lesson
Lesson
Lesson
Lesson
Lesson
Centrifugal casting
Gravity die casting
Vacuum die casting
Squeeze die casting
Casting equipment care and
maintenance
7
8
9
10
11
Module 4.
Lesson 1.
Lesson 2.
Lesson 3.
Lesson
Lesson
Lesson
Lesson
Lesson
Lesson
Lesson
Lesson
Lesson
Lesson
4.
5.
6
7
8
9
10
11
12
13
MACHINING OF METALS
Introduction to machining
Tools, equipment and safety
practices
Interpret working drawing and
sketches
Select and cut workshop materials
Perform shop computation
Measure work piece
Perform bench work
Turn work piece
Mill work piece
Grind work piece
Shape work piece
Repair work piece
Equipment care and maintenance
MID TERM EXAMINATION PERIOD
Write Midterm Exam Here
October
3, 2020
October
10, 2020
Presentation of
report and class
discussion
Respond to the
questions/ queries
raised in the class.
Interactive class
discussion via
online classes.
Presentation of
report and class
discussion
October
17, 2020
Respond to the
questions/ queries
raised in the class.
Respond to the
questions/ queries
raised in the class.
October
24, 2020
October
31, 2020
Interactive class
discussion via
online classes.
On-time submission
of Midterm exam
MODULE 5 JOINING OF METALS
When you have completed this module, you will be
able to:
1. Explain the principles and strategies used for
the casting of metals.
2. Apply safety practices in metal casting
process
November
3. Learn appropriate use of tools and 7, 2020
equipment for joining metals.
Module 5.
Lesson 1.
Lesson 2.
Lesson 3.
Lesson 4.
Lesson 5.
JOINING OF METALS
Introduction to joining
Safety practices
Perform industry calculation
Hand tools
Set-up welding equipment
Lesson 6
Fit up weld materials
Lesson 7
Repair welds
Lesson 8
Equipment care and maintenance
MODULE 6 APPLICATION OF REFRIGERATION AND
AIR-CONDITIONING
When you have completed this module, you will be
able to:
1. Explain the principles and strategies used for the
installation of refrigeration and air-conditioning
system and controls.
2. Use mathematical skills to solve problems in
electrical, heating, ventilating, air-conditioning,
and refrigeration systems.
3. Learn troubleshooting skills to diagnose and
repair.
4. Learn appropriate use of tools and equipment for
repairing, testing, and installation of
5. Learn to operate refrigeration and airconditioning systems and controls.
6. Learn how to follow safe working practice and
proper handling of refrigerants.
Module 6.
Lesson 1.
Lesson 2.
Lesson 3.
Lesson 4.
APPLICATIONS OF REFRIGERATION
AND AIR-CONDITIONING
Introduction to refrigeration and airconditioning
Matter, laws of refrigeration and
thermodynamics
Perform mensuration and
calculations
Bench works
November
14, 2020
Respond to the
questions/ queries
raised in the class.
Interactive class
discussion via
online classes.
Presentation of
report and class
discussion
Respond to the
questions/ queries
raised in the class.
November
21, 2020
November
28, 2020
Interactive class
discussion via
online classes.
Presentation of
report and class
discussion
Lesson 5.
Lesson 6
Electrical works
Maintain tools and equipment
Lesson 7
Lesson 8
Housekeeping practices
Installation of refrigeration and airconditioning systems
FINAL EXAMINATION
December
5, 2020
December
12, 2020
December
19, 2020
Interactive class
discussion via
online classes.
Presentation of
report and class
discussion
On-time submission
of Final exam and
all requirement of
the course
COURSE REQUIREMENTS
MID TERM –
1. Attendance
2. Class Participation/Reporting
3. Mid Term Examination
FINAL TERM –
1.
2.
3.
4.
5.
Attendance
Class Participation/Reporting
Final Practical Examination
Projects
Modules
PREPARED BY
NOTED:
RODRIGOG. BUSTILLOS JR.
Faculty
PAULITO C. NISPEROS
Dean