International Journal of Trend in Scientific Research and Development (IJTSRD)
Volume: 3 | Issue: 4 | May-Jun 2019 Available Online: www.ijtsrd.com e-ISSN: 2456 - 6470
Automatic Plant Watering System using
Arduino UNO for University Park
Yin Yin Nu1, San San Lwin2, Win Win Maw3
1Lecturer,
Department of Information Technology, Technological University, Monywa, Myanmar
Department of Information Technology Engineering, Technological University, Kyaukse, Myanmar
3Lecturer, Faculty of Computer System and Technologies, University of Computer Studies, Mandalay, Myanmar
2Lecturer,
How to cite this paper: Yin Yin Nu | San
San Lwin | Win Win Maw "Automatic
Plant Watering System using Arduino
UNO for University Park" Published in
International Journal of Trend in
Scientific Research and Development
(ijtsrd), ISSN: 24566470, Volume-3 |
Issue-4, June 2019,
pp.902-906,
URL:
https://www.ijtsrd.c
om/papers/ijtsrd23
IJTSRD23714
714.pdf
Copyright © 2019 by author(s) and
International Journal of Trend in
Scientific Research and Development
Journal. This is an Open Access article
distributed under
the terms of the
Creative Commons
Attribution License (CC BY 4.0)
(http://creativecommons.org/licenses/
by/4.0)
ABSTRACT
Watering is the most important cultural practice and most labor intensive task in
daily greenhouse operation. Watering systems ease the burden of getting water
to plants when they need it. Knowing when and how much to water is two
important aspects of watering process. To make the gardener works easily, the
automatic plant watering system is created. There have a various type using
automatic watering system that are by using sprinkler system, tube, nozzles and
other. This system uses Arduino UNO board, which consists of ATmega328
microcontroller. It is programmed in such a way that it will sense the moisture
level of the plants and supply the water if required. This type of system is often
used for general plant care, as part of caring for small and large gardens.
Normally, the plants need to be watered twice daily, morning and evening. So,
the microcontroller has to be coded to water the plants in the greenhouse about
two times per day. However for most people it becomes challenging to keep
them healthy and alive. This system automation is designed to be assistive for
the University Park. This system hopes that through this prototype people will
enjoy having plants without the challenges related to absent or forgetfulness.
Keywords: Automatic Plant Watering System, Arduino UNO board, relay module,
power supply and moisture sensor
1. INTRODUCTION
Arduino is an open-source electronics electronic platform
based on easy-to-use hardware and software. Arduino
boards are able to read inputs- light of sensor, a finger on a
button, or a Twitter messages,- and turn it into an outputactivating on a motor, turning on an LED, publishing
something online. Over the years Arduino has been the brain
of thousands of projects, from everyday objects to complex
scientific instruments. A worldwide community of markers
has gathered around this open-source platform, their
contributions have add to up an incredible amount of
accessible knowledge that can be of great help to novices and
experts alike.
Arduino was born at the Lvrea Interaction Design Institute
as an easy tool for fast prototyping, aimed at students
without a background in electronics and programming. As
soon as it reached a wider community, the Arduino board
started changing to adapt to new needs and challenges,
differentiating its offer from simple 8-bit boards to products
for IoT application, wearable, 3D printing, and embedded
environments. All arduino boards are completely opensource, empowering users to build them independently and
eventually adapt them to their particular needs. The
software too, is open-source, and it is growing through the
contributions of users worldwide.
@ IJTSRD
|
Unique Paper ID – IJTSRD23714
|
2. SYSTEM BLOCK DIAGRAM
Figure: 1 Block diagram of automatic plant watering
system.
There are two functional components in this system. They
are the moisture sensors and the motor/water pump. Thus
the Arduino Board is programmed using the Arduino IDE
software. The function of the moisture sensor is to sense the
level of moisture in the soil. The motor/water pump supplies
water to the plants.
3. SYSTEM REQUIREMENTS
The description of hardware and software components
required in the design and implementation are as follow:
Volume – 3 | Issue – 4
|
May-Jun 2019
Page: 902
International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
Figure:5 Relay module
Hardware Descriptions
 ATmega 328 microcontroller
 Moisture sensor
 12V DC motor
 Relay module
 Jump wire
 Power supply
Software Description
 Arduino IDE
Figure: 6 5V Relay Terminal and Pins
Figure: 2 ATmega 328 microcontroller
Figure: 7 12V DC motor
4. SYSTEM WORKING DESIGN
For the purpose of building this system one will need to
properly connect following:
Figure: 3 ATmega 328(AVR) pins
Figure: 8 All materials connected into the system
4.1
Arduino (UNO) Board
Figure: 4 Moisture sensor
Figure: 9 Arduino UNO Board
@ IJTSRD
|
Unique Paper ID – IJTSRD23714
|
Volume – 3 | Issue – 4
|
May-Jun 2019
Page: 903
International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
This is an Arduino UNO board. Before using it, the program
can be compiled from the computer or laptop. After
compiling the program, it is ready to use.
4.2 The process of making system
Step1: Firstly, Arduino UNO board, relay module, power
supply and moisture sensor are setup on the board. These
processes are shown in figure;
4.3 Pins configuration
Pins configuration of sensorArduino
Sensor
3.3V pin
=
Vcc
GND pin
=
GND
A0
=
A0
Step2: And then relay and Arduino UNO board are connected
in all pins,
Pins configuration of relay moduleArduino
Relay
5V pin
=
Vcc
GND pin
=
GND
13 pin
=
Signal
4.4 Write the program using Arduino IDE
The user have had the Arduino IDE software to write the
program.
Arduino UNO board is connected to the computer using the
USB cable. And then, double-click the Arduino application,
and then write the program.
Step3: Moisture sensor is also connected to the UNO board to
sense the water content of the plant. This process is shown
in figure;
Step4: In this step, the motor is connected to the relay. This
is as follows;
Figure:10 Start creating screen of arduino program
This program uses the functions pinMode(), digitalWrite(),
and delay(), which are provided by the internal libraries
included in the IDE environment. The user can select the
suitable board in the tools bar.
@ IJTSRD
|
Unique Paper ID – IJTSRD23714
|
Volume – 3 | Issue – 4
|
May-Jun 2019
Page: 904
International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
Figure: 11 Select the board
And then, select the serial/COM port that Arduino is attached
to:
Tools > Port > COM 3.
Figure: 13 Upload the program
After uploading the program, the user can see the amount of
water content the soil with the serial monitor. The amount of
water content is shown by the percentage in figure: 14.
Figure:12 Select the serial port
If the users selected the serial port, the users can write the
coding for the process.
Now, simply click the “Upload” button in the environment.
Wait a few seconds – the users should see the RX and TX leds
on the board flashing. If the upload is successful, the message
“Done uploading.” will appear in the status bar.
@ IJTSRD
|
Unique Paper ID – IJTSRD23714
|
Figure: 14 Monitoring the amount of moisture
5. CODING FOR THE PROCESS
int moisture_sensor = A0;
int moisture;
int limit = 40;
int WATERPUMP = 13;
void setup()
{
Serial.begin(9600); // opens serial port,
sets data rate to 9600 bps
pinMode(moisture_sensor,INPUT);
pinMode(WATERPUMP,OUTPUT);
}
Volume – 3 | Issue – 4
|
May-Jun 2019
Page: 905
International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
void loop()
{
moisture = analogRead(moisture_sensor);
moisture=map(moisture,550,0,0,100);
Serial.print("Moisture=");
Serial.print(moisture);
Serial.println("%");
if (Serial.available());
{
int speed= Serial.parseInt();
{
analogWrite(WATERPUMP,speed)
;
}
if (moisture>limit)
{
digitalWrite(13,LOW);
}
}
delay(400);
}
6. CONCLUSION
Although it seems to be more demanding and challenging,
there are many other possibilities like creating complex
connections of plants of similar variety or so-called "Internet
of Plants". Also, using more than one sensor is another idea
for an experimental venture, but there are also many other
experimental and challenge-like ideas such as using solar
power supply, timer for setting irrigation system etc.
However, independently of the way used to construct it,
there is no doubt that this system can be very helpful in
Unique Paper ID – IJTSRD23714
microcontrollers/
[3] https://vigyanashram.files.wordpress.com/
2015/05/plant-watering-system.pdf
digitalWrite(13,HIGH);
|
REFERENCES
[1] https://components101.com/
arduino-uno
[2] http://www.circuitbasics.com/setting-up-a-5v-relayon-the-arduino/
else
@ IJTSRD
solving many problems, from those that seem harmless to
those that are on the scale of the most important and most
dangerous ones for human population. By means of this
system, it is possible to control the amount of water released
from the process of watering the plant. This system
automation is designed to be assistive for the University
Park. Although it can be very helpful for humanity in general,
agriculturists, craftsmen, and botanists could have the
biggest benefit of using this system.
|
[4] https://learn.sparkfun.com/tutorials/installingarduino-ide/all.pdf
[5] [14 Dez] Devika et al., International Journal of
Advanced Research in Computer Science and Software
Engineering 4(10), October - 2014, pp. 449-456
[6] [16 San] Sandeep K. Shukla, IIT Kanpur, Introduction
to embedded system, Aug 29, 2016
[7] [16 SHA] SHAIKH SHEROZ MOHD HASAN, ‘AUTO
IRRIGATION USING ARDUINIO’2016
[8] [17 N.Du] N. Đuzić and D. Đumić: Automatic Plant
Watering
System
and
its
Applications,
Coll.Antropol. 41 (2017)
Volume – 3 | Issue – 4
|
May-Jun 2019
Page: 906