International Research Journal of Engineering and Technology (IRJET)
e-ISSN: 2395-0056
Volume: 06 Issue: 03 | Mar 2019
p-ISSN: 2395-0072
www.irjet.net
A LITERATURE STUDY ON FAULT RECOGNITION IN DIFFERENT SYSTEM
BALAKUMARAN R M1, ANANDHI S2, DILIPKUMAR B3, D. SIVANANDAKUMAR4
1,2,3,4Department
of Electronic and Instrumentation Engineering, Erode Sengunthar Engineering College,
Erode, India.
---------------------------------------------------------------------***---------------------------------------------------------------------Abstract - This paper presents an overview and an approach of Fault discovery assumes a vital job in staggering expense and
wellbeing basic procedures. Early identification of procedure flaws can help keep away from anomalous occasion movement.
Fault identification can be cultivated through different methods. This paper displays the writing review of real techniques and
ebb and flow condition of research in the field with a determination of essential commonsense applications.
Key Words: fault, staggering expense, different methods, ebb.
1. INTRODUCTION
This paper speaks to the Line Protection on the utilizations of fault location innovation. This tends to the recognition of
those irregular conditions where a conductor breaks and does not contact either another conductor or a grounded
component. Recognition of fault on line is finished via mechanization. As fault examination wound up imperative
prerequisites of the electric power framework to wind up progressively exact. There are mixes of an electrical switch and a
transfer security framework in a run of the mill fault cleaning framework. The primary parts in security framework are
wiring, transducers, assistant power supply, switches, circuit breakers, transfers and the working loop of the electrical
switch. Prior fault is naturally cleared by electromagnetic transfers. The electrical amount, which is voltage or a flow, was
changed to a mechanical power which worked the transfer when a preset edge was surpassed. However at this point a
days the strong state transfers are grown with the goal that the activity can be performed effectively and precisely.
1.1 TYPES OF FAULTS
There are mainly two types of faults in the electrical power system. Those are as following:
1.
Symmetrical
2.
Unsymmetrical faults.
This technique is used to reach a strong conclusion of the power grid monitoring & controlling without manpower is
SCADA.
1.
Symmetrical faults:
These are very severe faults and occur infrequently in the power systems. These are also called as balanced faults.
There are mainly two types namely
1. Line to line to line to ground (L-L-L-G) and
2. Line to line to line (L-L-L)
Three phase fault analysis or information is required for selecting set-phase relays, rupturing capacity of the circuit
breakers and rating of the protective switchgear.
2.
Unsymmetrical Faults:
These are very common and less severe than symmetrical faults. There are mainly three types namely
1. Line to ground (L-G),
2. Line to line (L-L) and
3. double line to ground (LL-G) faults.
© 2019, IRJET
|
Impact Factor value: 7.211
|
ISO 9001:2008 Certified Journal
|
Page 2133
International Research Journal of Engineering and Technology (IRJET)
e-ISSN: 2395-0056
Volume: 06 Issue: 03 | Mar 2019
p-ISSN: 2395-0072
www.irjet.net
2. LITERATURE SURVEY
Sl
no
1.
2.
3.
4.
Authors, years.
Abstract
Technology used
Conclusion of authors..
Praveen Reddy ,
Samreen Kausar,
Uppalpati
Ramyashree Laxmi
,
Varadi Sahana
May 2018
Ire Journals
Volume 1 Issue 11
In power the board venture, the
PC is utilized for appointing the
need for different burdens.
In the event that there any issue
happens in plant, we can without
much of a stretch distinguish
which part is trip. After that we
can investigate the issue through
labor and screen the substation.
PLC,SCADA
With the assistance of Switchyard
and transmission framework
Automation we can improve
dependability, Power Quality and
power taking care of and conveyance
limit/the executives. The usage of
computerization is exorbitant and
complex strategy with expanding
utilization of intensity hardware and
gadgets gear, for execution in handy
existing field.
So as to deal with dubious
components, including breaking
down and other ill-advised activities
of PRs and CBs, notwithstanding
false as well as missing cautions, a
shot obliged programming model is
brought into power framework fault
determination. The Monte Carlo
reproduction based hereditary
calculation is utilized to comprehend
the created enhancement show.
Moreover, the calculation speed of
the created strategy meets the
necessities of on-line fault finding
applications.
Huizhong Song , At the point when a fault happens
Stochastic
Ming Dong ,
in a segment or a part of a given
Programming
Rongjie Han,
power framework, the failing of
Fushuan Wen
defensive transfers (PRs) and
Md. Abdus Salam , circuit breakers (CBs), and the
Xiaogang Chen ,
false and missing cautions, may
Hua Fan and
obviously entangle the fault
Jian Ye
conclusion strategy. As a part of
20 July 2018
stochastic programming, the all
around created possibility
compelled programming
approach gives a proficient
method to take care of
programming issues full of
vulnerabilities. The hereditary
calculation joined with Monte
Carlo reenactments are then
utilized to tackle the advancement
demonstrate.
Divyapradeepa T
In this paper we portray a
PLC & SCADA
Vol. 6, Issue 11,
procedure which is utilized to
November 2017 achieve a solid decision about the
power lattice observing and
controlling through SCADA. On
the off chance that issue happens,
the hand-off will trip so we can
without much of a stretch
distinguish the area and
investigate the issue through
labor and screen the substation.
Ing. Komi Agbesi1,
The framework naturally
GSM modem,
Felix Attuquaye distinguishes faults, examinations
PIC 16F877
Okai,
and arranges these deficiencies
Microcontroller,
January 2016
and afterward, computes the fault RS-232 connector
separation from the control room
utilizing an impedance-based
calculation strategy. At long last
the fault data is transmitted to the
control room. Taking everything
into account, the time required to
find a fault is radically diminished,
as the framework naturally and
© 2019, IRJET
|
Impact Factor value: 7.211
|
The utilization of PLCs
(Programmable Logic Controllers) in
substation and dispersion
robotization application has
developed as of late. The financial
aspects of plc based arrangement
imply that substation mechanization
and SCADA arrangement can be
connected considerably more
broadly.
In end the proposed framework will
give a decrease in the time required
to find a fault via consequently giving
exact fault area data. It will likewise
permit administrators, for example,
GRID to accurately identify and find
faultd sections on their transmission
lines and, accordingly, limit control
desruptions to dissemination
substations and help spare costly
transformers.
ISO 9001:2008 Certified Journal
|
Page 2134
International Research Journal of Engineering and Technology (IRJET)
e-ISSN: 2395-0056
Volume: 06 Issue: 03 | Mar 2019
p-ISSN: 2395-0072
5.
Kunjin Chen,
Caowei Huang,
Jinliang He
10th February
2016
6.
Majid Jamil,
Rajveer Singh∗,
Sanjeev Kumar
Sharma
1 March 2015
www.irjet.net
precisely gives exact fault area
data.
An extensive survey on the
Hybrid
strategies utilized for fault
Transmission
identification, order and area in Lines, Wide-Area
transmission lines and
Fault Location,
conveyance frameworks is
Seriesintroduced in this examination.
Compensated
Fault location procedures are Lines, Fuzzy Logic,
talked about on the premise
Artificial Neural
offeature extraction.
Network.
In this proposed work a fuzzy
logic based calculation utilizing
discrete wavelet change is
produced for distinguishing the
different faults in the electrical
conveyance framework for an
uneven appropriation electrical
power framework. This method is
fit to distinguish the ten distinct
sorts of deficiencies with
insignificant impact of variety in
fault initiation point, stacking and
different parameters of the power
appropriation framework.
7.
Daniel J Hansen P As a lesson learned from a real.E . , NRG Energy, world incident, discovery of the
Inc.
vulnerability occurred during the
2014 IEEE
investigation of a generating unit
trip from a nearby switchyard
fault immediately outside a
generator step-up transformer
(GSU) differential zone of
protection. Problem resolution is
correctable or minimized with the
available features of
microprocessor differential relays,
with sufficient winding inputs,
and the proper application of
current transformer connections.
8.
M.M. Mansour a,
The Petri nets are utilized as a
Mohamed A.A.
demonstrating apparatus to
Wahab b, Wael M. manufacture fault finding models
Soliman c,*
of thing/section(s) of intensity
© 2019, IRJET
|
Impact Factor value: 7.211
|
An assortment of techniques are
presented and agent works are
introduced in detail.
Notwithstanding the traditional
models, for example, ANN and SVM,
we likewise present some
encouraging new models developed
of late. we propose the conceivable
pattern for future works, including
the use of models, for example, RBM
and CNN. We likewise advanced the
likelihood of utilizing the most recent
AI models to encourage the fault
loclocation assignments.
Fuzzy Logic & The structure of any electrical power
Discrete Wavelet
dispersion framework regularly
Transform
changes in view of the changing of
burden designs, exchanging of
intensity framework supplies,
sudden separate of producing units,
and so on. The proposed strategy is
completely compelling in arranging
every one of the ten sorts of issues
and for any conceivable blend of
various power framework
parameters. The testing of the
proposed technique under different
working conditions, diverse fault
opposition and fault origin edges and
correspondingly result got
demonstrates that the outcomes are
acceptable.
Microprocessor
A noteworthy contributing
Differential
component to the mis-task is the
Relays,
main fault: a line-to-ground fault on
the C period of the 230kV East Bus,
bringing about the clearing of the
transport and opening the No. 3A
breaker. With the second fault, all
fault current commitments from the
nearby switchyard go through the 3B
and 3C breakers to the fault.
Something else, the flows of the
second fault could have part between
parallel ways; the flows through the
3B and 3C breakers could have been
considerably less. it is sensible to
infer that little contrasts in the CT
execution sufficiently made variety
in the differential hand-off info,
bringing about an activity.
Petri Nets
The proposed strategy can be
connected on expansive power age
station through building Petri net
model for each segment. In addition,
ISO 9001:2008 Certified Journal
|
Page 2135
International Research Journal of Engineering and Technology (IRJET)
e-ISSN: 2395-0056
Volume: 06 Issue: 03 | Mar 2019
p-ISSN: 2395-0072
www.irjet.net
21 May 2013
station which intend to analyze
precisely the deficiencies when an
extensive sum data of SCADA
framework is recognized in the
control room. It can analyze and
appraise the defective
thing/section(s) accurately for
numerous shortcomings just as
straightforward issues.
9. Ravi V. Ghodchar
Larger part of deficiencies
and
happening in these power
Dr. R.G.Karandikar frameworks are because of flaws
NOVEMBER 2013
in the transmission lines. This
paper introduces a thorough
writing study for similar
investigation of various strategies
utilized for fault recognition and
examination dependent on
wavelet change.
10.
C. Fortunato*, A.
Casaca**, A. Grilo**
and M. Santos*
FEB 2012
11.
Wenxin Guo,
Fushuan Wen,
Gerard Ledwich,
Senior Member,
IEEE, Zhiwei Liao,
Xiangzhen He, and
Junhui Liang
VOL. 25, NO. 3,
JULY 2010
12. Abolfazl Rahmani,
Javad Haddadnia
Omid seryasat
2010 IEEE
© 2019, IRJET
|
it can manage mis-tasks of the circuit
Breakers.
Different
Methodologies
Used
wavelet based strategy is best for the
investigation of L-L-L fault, DL-G
fault can't be recognized by it. The
technique including DWT alongside
the SVM gives lesser productivity of
L-L-L fault recognizable proof; still it
gives high precision for different
sorts of fault. Accordingly we infer
that this strategy is most fitting one
for transmission line fault discovery
and grouping.
Wireless Sensor
In the proposed methodology, the
Network
obtained current signs, hotspots
pictures signs and interruption
recognition pictures are transmitted
to the SCADA System. To recognize
the flawed task it will be utilized the
program to identify the towers in
which the deficiencies exist. This
Project can likewise be incorporated
into the Distribution Automation
(DA), which is a key part of the keen
network. The sensors, then again,
could transmit the signs of fault area
so as to address it by means of the
switch in MV blended systems..
The hardware and software
architectures of the envisaged
sensor solution will also be
described and finally, the
integration of this system into
Smart Grids will be discussed in
terms of automatic fault analysis.
The purpose is to obtain faster
and more reliable information
about the disruptions in the
power distribution network and
their location. Furthermore, the
wireless sensors allow remote
detection of medium and low
voltage (MV/LV) power
transformer hotspots in order to
identify emerging malfunction as
well as detection of intrusion in
the MV/LV power transformers.
Accordingly, the unpredictability Relays And Circuit
of the fault determination could
Breakers
be enormously expanded. The
current investigative models for
power framework fault
determination don't efficiently
address the conceivable
breakdowns of PRs and
additionally CBs, and thus may
prompt wrong conclusion results
if such glitches do happen.
In light of the current diagnostic
Thermo Vision
model-based strategies, a novel
Technique
logical model is exhibited for
power framework fault analysis
with breakdowns of PRs and CBs
considered. The created model
couldn't just gauge the fault
Impact Factor value: 7.211
|
In light of the current expository
model-based strategies, a novel
systematic model is displayed for
power framework fault finding with
breakdowns of PRs and CBs
considered. The created model
couldn't just gauge the fault areas,
yet in addition recognize the broke
down PRs and CBs, just as the
erroneous and missing cautions.
In this paper a productive procedure
for the insightful recognition of two
sorts of the deficiencies happened in
low presser boards of dissemination
systems has been displayed by
utilizing ZM and SVM. At last the kind
of the issues in the link head and
ISO 9001:2008 Certified Journal
|
Page 2136
International Research Journal of Engineering and Technology (IRJET)
e-ISSN: 2395-0056
Volume: 06 Issue: 03 | Mar 2019
p-ISSN: 2395-0072
www.irjet.net
segments, yet in addition
distinguish the failed PRs and CBs,
just as the erroneous and missing
cautions.
13.
M. M. Ahmed,
SCADA , RTUs and electrical cable
Member, IEEE and correspondence (PLC) framework
W. L. Soo
have been utilized and created for
2008 IEEE
recognizing, fault finding, fault
confining, fault isolating and
power rebuilding as far as
equipment and programming.
fault administration investigate
take a shot at client side
substation for working and
controlling between the purchaser
side framework and the
substation.
SCADA, RTU
14.
Heung-Jae Lee,
Member, IEEE,
Bok-Shin Ahn,
Member, IEEE, and
Young-Moon Park,
Fellow, IEEE
JANUARY 2000
Distribution
substations
The regressive inaccurate
thinking process is connected for
the fault area estimation utilizing
the learning of topology, the task
principles of defensive gadgets,
heuristic information of very
much prepared administrators,
and quick alerts. The proposed
framework has been tried in a
nearby control focus in Korea as a
piece of a smart direction
framework for the SCADA
administrators.
circuit base, that were like one
another and their separation was
troublesome. By thoughtfulness
regarding the decent variety and
spread of the hardware of
dissemination organizes, the value
and adequacy of the introduced
technique is increasingly selfevident.
This exploration advances staff
productivity by conveying staff to on
location area just when essential.
The working framework depicted
here can decrease the quantity of
blackouts and isolate the clients
influenced by the shortcomings from
the individuals who are not
influenced the fault blackouts. In any
case, clients still experience a
momentary blackout amid the low
side and high side checking until the
suitable exchanging capacities are
enacted and the fault area is to be
actually recognized.
An on-line fault analysis master
framework was created to help the
SCADA administrators. The
framework analyze different faults in
numerous substations dependent on
the estimated thinking process.
3. CONCLUSION
Early fault recognition can limit plat downtime, broadened gear life, increment the wellbeing and decrease fabricating
costs. Number of issues must be viewed as while picking specific fault recognition technique. Most critical are: sort of
disappointments, depiction of procedure structure, process elements, accessible procedure signals, process
unpredictability, accessible measure of procedure input-yield information and procedure reasonableness for portrayal
regarding rules. Easiest methodology is immediate farthest point checking of quantifiable variable. A few procedures
produce intermittent or stochastic signs that can be utilized for fault discovery if changes in flag models are brought about
by procedure shortcomings. At the point when extensive measure of procedure input-yield information can be acquired,
yet process structure is obscure or too complex to possibly be displayed, design acknowledgment techniques can be
utilized. Procedure display based fault discovery incorporates process elements and non-quantifiable state factors, yet
requires exact models and is less demanding to apply for all around characterized procedures, for example, electrical and
mechanical then for warm and concoction forms. On the off chance that fundamental connection among shortcomings and
manifestations is known in type of principles information based strategies are the decision.
REFERENCE
1)
R. Isermann, Fault-Diagnosis Systems, Springer, Berlin, 2006
© 2019, IRJET
|
Impact Factor value: 7.211
|
ISO 9001:2008 Certified Journal
|
Page 2137
International Research Journal of Engineering and Technology (IRJET)
e-ISSN: 2395-0056
Volume: 06 Issue: 03 | Mar 2019
p-ISSN: 2395-0072
www.irjet.net
2)
R. Isermann,“Model-Based Fault Detection And Diagnosis-Status And Applications”, Annual Reviews in Control, Vol.
29, Is. 1, 2005
3)
R. Isermann, "Process Fault Detection Based on Modeling and Estimation Methods–A Survey”, Automatica, Vol. 20, No.
4, 1984
4)
I. Castillo and T. Edgar, “Model Based Fault Detection and Diagnosis”, TWCCC Conference, Spring 2008, Austin, Texas
5)
V. Venkatasubramanian, R. Rengaswamy, S. N. Kavuri and K. Yin, “A review of process fault detection and diagnosis
Part I: Quantiative model-based methods”, Computers and Chemical Engineering, No. 27, 2003,pp. 293-311
6)
V. Venkatasubramanian, R. Rengaswamy and S. N. Kavuri, “A review of process fault detection and diagnosis Part II:
Qualitative models and search strategies”, Computers and Chemical Engineering, No. 27, 2003, pp. 313-326
7)
V. Venkatasubramanian, R. Rengaswamy, S. N. Kavuri and K. Yin, “A review of process fault detection and diagnosis
Part III, Process history based methods”, Computers and Chemical Engineering, No. 27, 2003, pp. 327-346
8)
S. Katipamula and M. R. Brambley, “Methods for Fault Detection, Diagnostics, and Prognostics for Building Systems –
A Review, Part I”, HVAC&R Research, Vol. 11, No. 1, January 2005
9)
S. Katipamula and M. R. Brambley, “Methods for Fault Detection, Diagnostics, and Prognostics for Building Systems –
A Review, Part II”, HVAC&R Research, Vol. 11, No. 2, April 2005
10)
A. S. Willsky, “A Survey of Design Methods for Failure Detection in Dynamic Systems”, Automatica, Vol. 12, pp. 601611, 1976
11)
L. H. Chiang, E. L. Russel and R. D. Braatz, Fault Detection and Diagnosisin Industrial Systems,SpringerVerlag,London,UK, 2001
12)
P. M. Frank, “Fault Diagnosis in Dynamic Systems Using Analytical and Knowledge-based Redundancy, A Survey and
Some New Results”, Automatica, Vol. 26, No. 3, pp. 459-474, 1990, UK
13)
S. Verron, T. Tiplica and A. Kobi, Fault detection of univariate non-Gaussian data with Bayesian network, IEEE
International Conference on Industrial Technology (ICIT'10), 2010
14)
Y. Tharrault, G. Mourot, J. Ragot and D. Maquin, “Fault Detection And Isolationwith Robust Principal Component
Analysis”, Int. J. Appl. Math. Comput. Sci., 2008, Vol. 18, No. 4, 429–442
15)
D. Garcıa-Alvarez, “Fault detection using Principal Component Analysis (PCA) in a Wastewater Treatment Plant
(WWTP)”, 62-th Int. Student's Scientific Conf, Saint-Petersburg, 13-17 April, 2009
16)
G. Verdier and Ariane Ferreira, “Adaptive Mahalanobis Distance and k-Nearest Neighbor Rule for Fault Detection in
Semiconductor Manufacturing”, EMSE-CMP WP 2009/14
17)
A. N. Vishwanath Rao, “Application of Auto Associative Neural Network for Aero Engine Control System Sensor Fault
Detection, Isolation and Accomodation”,DRDO Sci.Spec.,March2009,pp.12-15
18)
J. L. Aravena and F. N. Chowdhury, “Fault Detection Of Flight Critical Systems”, DASC. The 20th Conf., Oct. 2001,
Daytona, Fla.
19)
H. Long and X. M. Wang, “Aircraft Fuel System Diagnostic Fault Detection Through Expert System”, 25th International
Congress of the Aeronautical Sciences, September 2006, Hamburg, Germany
20)
F. Kimmich and R. Isermann, “Model Based Fault Detection For The Injection, Combustion And Engine-Transmission”,
15th IFAC, 21–26 July 2002
© 2019, IRJET
|
Impact Factor value: 7.211
|
ISO 9001:2008 Certified Journal
|
Page 2138