EUROPEAN STYLE PRESS
BRAKE TOOLING
Solutions for Press Brake Tooling
Extend The Life Of Your Tools With Nitrex™
Nitrex™ high endurance surface enhancement, exclusively from Wilson Tool, increases press
brake tooling life by several times that of standard tooling. With a surface hardness of HRC-60
and a consistent 0.5mm of penetration below the surface of the tool, Nitrex™ adds lubricity to
press brake tooling and lowers the coefficient of friction as the material slides over the
shoulder of the V-opening on a die. Any Wilson Tool press brake punch or die can be
enhanced with Nitrex™.
Nitrex™ High Endurance Surface Enhancement
Patent Number: 6,327,884 B1
Save Time And Money With The Wilson Express Clamping
System™
Available for virtually any make and model of press brake, the
Wilson Express Clamping System is uniquely designed to
increase your productivity and reduce your operating costs.
• Load Punches in a Snap
Loading punches has never been easier. The Wilson Express
Clamping system completely eliminates the need to slide
punches in from the end of the machine. Simply place (415mm)
long punches or individual pieces of sectionalized punches
under the clamps and push them upward. The spring-loaded
clamps capture the punch via the safety groove and hold it in
place until the clamps are locked. To lock the clamps, simply
push the removable lever upward.
• Unload Punches Quickly and Easily
Again, Wilson has eliminated the need to slide punches to the
end of the machine. Simply pull down the locking lever
to unlock the clamp, then to remove smaller punch sections,
pushing inward on the tops of the clamps opens the clamps and
allows the operator to pull individual sections straight down.
Clamp Plates that are not in use can easily be removed from the
punch holders by hand.
• No Special Tooling Required
Wilson Express Clamping Systems can be used with any
standard European style press brake tooling with a safety
groove. You can use the same high quality Wilson tooling you
currently own, without having to re-purchase the system for every
tool you order.
• Fewer Maintenance Costs
Because the Wilson Express Clamping System is mechanical
rather than hydraulic, maintenance costs are virtually eliminated.
And with no hydraulics there’s no risk of power failures causing
clamps to release unexpectedly.
• Dual Clamping Available
A dual clamping feature is available on all Wilson Express
Clamping Systems for an additional cost. This added feature
allows you to load punches with the safety groove facing forward
or to the rear of the machine. Both front and rear clamps are
opened and closed simultaneously when the locking lever is
actuated.
For a free demonstration, or for more information on the Express Clamping System™ , please contact your local
Wilson Tool International® sales engineer or our sales desk on 0800 012 1475.
Terms and Conditions
4
Order
Minimum order is £35.00
Credit
All orders are subject to the approval of our credit department. If you are a new account,
please furnish us with a bank reference and three supplier references. A credit limit will
be imposed on new accounts until credit has been established.
Payment
Terms are net 30 days.
Cancellation
In the event an order is cancelled, a charge will be made to cover labour, materials and
overheads.
Returned Material
A handling charge of 25% is made on all standard parts returned for credit. Written
permission and shipping instructions must be obtained before the return of any material.
Special tooling cannot be returned.
Claims
All claims for shortages must be made within 3 days of the invoice date.
Prices
rices and specifications subject to change without prior notice. E & OE. All prices are
P
exclusive of VAT.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
STANDARD PUNCH & DIE LENGTHS
Standard Punch Lengths
Features:
(S)
1. Most tools can be easily loaded by a
single operator.
415mm
2. Easy to store.
3. All sectionalised tools come pre-cut in
nine different pieces.
4. Most sectionalised punches include two
ear pieces (horns).
(L) 835mm
5. Punches are induction hardened, to
59-60 HRC but NITREX™ (HRC -60) is
available for every punch in the tooling
line.
6. Special Tooling available. Please contact
the sales desk.
(X) 835mm
SECTION WIDTHS:
100mm LEFT EAR / 100mm RIGHT EAR / 10mm / 15mm / 20mm / 40mm / 50mm / 200mm /
300mm
Note: Special lengths are available at additional cost, just select the standard length and ask us to cut to your requirements.
Standard Die Lengths
Features:
(S) 415mm
1. Most tools can be easily loaded by a
single operator.
2. Easy to store.
3. All sectionalised tools come pre-cut in
nine different pieces.
(L) 835mm
4. Most dies are NITREX enhanced (HRC
60) as standard. Others are induction
hardened.
(X) 835mm
5. Special Tooling available. Please contact
the sales desk.
SECTION WIDTHS:
100mm / 100mm / 10mm / 15mm / 20mm / 40mm / 50mm / 200mm / 300mm
Note: Special lengths are available at additional cost, just select the standard length and ask us to cut to your requirements.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
5
QUICK REFERENCE CHART
90° BENDING
(0.5 - 3.5mm)
90° BENDING
WITH THIN TIP PUNCH
90° BENDING
WITH NARROW PUNCH
STANDARD PUNCHES
WITH THIN TIP
PAGE 13
STANDARD PUNCHES
PAGE 12 & 23
90° BENDING
WITH THIN TIP GOOSENECK PUNCH
NARROW PUNCHES
PAGE 18 & 24
90° BENDING
(SASH)
90° BENDING
WITH GOOSENECK PUNCH
GOOSENECK
PUNCHES
WITH THIN TIP
PAGE 16
GOOSENECK
PUNCHES
PAGE 14-17
ACUTE ANGLE BENDING
(0.5 - 2.0mm)
90° BENDING
2V QUICK CHANGE DIES
ACUTE ANGLE
PUNCHES PAGE
20-21
SASH PUNCHES
PAGE 19-20
90° BENDING
1V QUICK CHANGE DIE - 60mm
QUICK CHANGE 2V
DIES PAGE 28-29
QUICK CHANGE 1V DIES
PAGE 38-41
2V DIE RAIL
PAGE 36
1V DIE RAIL
PAGE 47
2V DIE HOLDERS
PAGE 37
6
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
QUICK REFERENCE CHART
90° BENDING
1V QUICK CHANGE - 83.5mm
ACUTE ANGLE BENDING
2V QUICK CHANGE DIES
QUICK CHANGE 1V DIES
PAGE 42-46
ACUTE ANGLE QUICK
CHANGE 2V DIE
PAGE 31
ACUTE ANGLE BENDING
1V QUICK CHANGE DIES
QUICK CHANGE 1V DIES
PAGE 38
2V DIE RAIL
PAGE 36
QUICK CHANGE 1V
HOLDERS
PAGE 48
2V DIE HOLDERS
PAGE 37
4V DIES
1V DIE RAIL
PAGE 47
ACUTE ANGLE BENDING
(2.5 - 5.0mm)
BOLT ON 2V DIES
ACUTE ANGLE PUNCHES
PAGE 21
4V DIES
PAGE 53
BOLT ON 2V
DIES
PAGE 33-35
ACUTE ANGLE
LARGE 1V DIES
PAGE 49
90° BENDING
(3.5 - 10.0mm)
HEMMING (2 STAGE)
(0.5 - 2.0mm)
ACUTE ANGLE
PUNCHES
PAGE 20-21
ACUTE ANGLE
PUNCHES
PAGE 22
STEP 1
2 STAGED HEMMING
HEMMING TOOLS
PAGE 56
HEMMING DIES
PAGE 55
LARGE
1V DIES
PAGE 50-52
STEP 2
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
7
QUICK REFERENCE CHART
1300
90° BENDING
(10 - 12.7mm)
LARGE RADIUS BENDING
LARGE RADIUS BENDING
(WITH URETHANE DIE)
LARGE RADIUS
PUNCHES
PAGE 26
LARGE RADIUS
PUNCHES
PAGE 26
LARGE RADIUS
PUNCHES
PAGE 26
URETHANE PADS
PAGE 58
LARGE 1V DIES
PAGE 50-52
URETHANE
HOLDERS
PAGE 57
LARGE 1V DIES
PAGE 50-52
HEMMING
(0.5 - 1.5mm)
HEMMING
(0.5 - 3.0mm)
DEEP BOX BENDING
STANDARD PUNCH
HOLDER (SUPPLIED WITH
MACHINE) OR NARROW
PUNCH HOLDERS
PAGE 63
NARROW PUNCH
HOLDERS
PAGE 63
FLATTENING PUNCHES
PAGE 25
FLATTENING PUNCHES
PAGE 25
FLATTENING DIES
PAGE 54
STANDARD PUNCHES
PAGE 12
LOW PROFILE QUICK
CHANGE 1V DIE
PAGE 44
QUICK CHANGE 1V DIE
HOLDERS
PAGE 48
3V HEMMING DIES
PAGE 54
OFFSET BENDING
(0.5 - 1.5mm)
DEEP PUNCH HOLDER
DEEP PUNCH
HOLDER
PAGE 64
RAIL STYLE OFFSET
TOOLS
PAGE 59
2V DIE RAIL
PAGE 36
2V DIE HOLDERS
PAGE 37
STANDARD
PUNCHES
PAGE 12
8
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
WILSON EXPRESS CLAMPING SYSTEM™
CAT. NO.
DESCRIPTION
43817i
43817i-2
PRICE
CAT. NO.
DESCRIPTION
Z1 Series with Wedge, 4 Clamp Interlocking
43818i
Z2 Series with Wedge, 4 Clamp Interlocking
Z1 Series with Wedge, 2 Clamp Interlocking
43818i-2
Z2 Series with Wedge, 2 Clamp Interlocking
PRICE
Note: Clamps to convert a press brake to European style are available. Contact sales engineer or sales desk on pb.sales@wilsontool.eu.com
Express Clamp Torque Wrench Kit
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
CAT. NO.
COMPONENT
8002
Complete Kit
8003
Case
43726
Pivots
6793
Wrench
6795
Hex Tips
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
PRICE
pb.sales@wilsontool.eu.com
9
EUROPEAN STYLE MANUAL CLAMPS
Z1 Punch Holder with Interlocking Wedge
Single Clamp
CAT. NO.
Dual Clamp
PRICE
CAT. NO.
43901i
PRICE
E43007i
Z2 Punch Holder with Interlocking Wedge
Single Clamp
CAT. NO.
Dual Clamp
PRICE
CAT. NO.
43904i
10
PRICE
E43008i
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
Solutions for your Euro style punch needs
Wilson Tool European Style press brake punches are made to the strictest manufacturing
standards using premium quality tool steels, guaranteeing the high-quality products our
customers have come to expect.
An extensive range of Wilson Tool European style punches is held in stock with different
tip radius in some cases. This means that many of the most popular punch options
can be despatched on the same day they are ordered, or within one or two days if a
modification is required.
STANDARD 88° & 90° PUNCHES
Part Part
No. 40002
No. 40002
Standard 88° Punches
30mm
30mm
35mm
35mm
R 5mm
R 5mm
"H" "H"
35mm
35mm
R
R
9mm 9mm
88
0
88
(Ear Pirce)
(Ear
Pirce)
(Ear
Piece
Max. = 47 Ton/Metre)
10mm
10mm
0
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40002
0.2
100
66.9
E40006
0.6
100
66.4
E40008
0.8
100
66.6
E40015
1.5
100
66.3
E40023
2.3
100
66.0
E40030
3.0
100
65.7
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
Part Part
No. 40102
No. 40102
Standard 90° Punches
4.130
4.130
[ 104.9
]
[ 104.9
]
30mm
30mm
these
are are
the the
rightright
sizesize
these
35mm
35mm
R 5mm
R 5mm
"H" "H"
35mm
35mm
R
R
(Ear (Ear
Piece)
Piece)
9mm9mm
10mm
10mm
90 90
0
0
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40102
0.2
100
66.9
E40108
0.8
100
66.7
E40115
1.5
100
66.4
E40123
2.3
100
66.0
E40130
3.0
100
65.7
(Ear Piece
Max = 47 Ton/Metre)
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
12
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
STANDARD 88° & 90° PUNCHES WITH THIN TIP
Standard 90° Punches With Thin Tip
Part No. 40202
Part No. 40202
30mm
30mm
"H"
"H"
10mm
10mm
R 5mm
R
R 5mm
R
4mm
90
5mm
(Ear Piece)
4mm
5mm
90
0
0
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40202
0.2
20
66.9
E40206
0.6
20
66.4
(Ear Piece)
(Ear 10mm
Piece
Max. = 10 Ton/Metre)
L
835 mm
10mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
Standard 88° Punches With Thin Tip
Part No. 40212
30mm
10mm
"H"
R 5mm
R
4.02mm
88
0
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40212
0.2
20
66.9
E40216
0.6
20
66.4
5mm
(Ear Piece)
(Ear Piece
Max. = 10 Ton/Metre)
L
835 mm
S
415 mm
10mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
13
88° GOOSENECK PUNCHES
88° Gooseneck Punches
(Ear Piece
Max. = 45 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40302
0.2
50
119.9
E40306
0.6
50
119.4
E40308
0.8
50
119.7
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
88° Gooseneck Punches
(Ear Piece
Max. = 45 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40402
0.2
50
104.9
E40406
0.6
50
104.4
E40408
0.8
50
104.6
E40415
1.5
50
104.3
E40430
3.0
50
103.7
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
14
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
88° GOOSENECK PUNCHES
88° Gooseneck Punches
(Ear Piece
Max. = 47 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40602
0.2
70
89.9
E40606
0.6
70
89.4
E40608
0.8
70
89.6
E40615
1.5
70
89.3
E40630
3.0
70
88.7
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
88° Gooseneck Punches
30mm
“H”
R
9mm
88°
UK
Ireland
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40103
0.8
50
159.65
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
L
835 mm
pb.sales@wilsontool.eu.com
S
415 mm
X 835 mm
SECTIONALISED
15
88° & 90° GOOSENECK PUNCH WITH THIN TIP
88° Gooseneck Punches With Thin Tip
(Ear Piece
Max. = 30 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40702
0.2
50
89.9
E40706
0.6
50
89.4
E40708
0.8
50
89.6
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
90° Gooseneck Punches With Thin Tip
(Ear Piece
Max. = 30 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40712
0.2
50
89.9
E40718
0.8
50
89.7
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
16
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
90° & 85° GOOSENECK PUNCHES
90° Gooseneck Punches
(Ear Piece
Max. = 45 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40502
0.2
50
104.9
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
85° Gooseneck Punches
(Ear Piece
Max. = 45 Ton/Metre)
R
mm
MAX. TON
PER METRE
“H”
E44540
4.8
100
105.0
E44560
6.35
100
104.3
CAT. NO.
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
17
88° & 90° NARROW PUNCHES
88° Narrow Punches
(Ear Piece
Max. = 12 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40802
0.2
50
95.0
E40806
0.6
50
94.5
*Note:
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.
Induction Hardened.
Nitrex™ (HRC-60) available for every punch in the tooling range at additional cost.
90° Narrow Punches
(Ear Piece
Max. = 12 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E40902
0.2
50
95.0
*Note:
18
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.
Induction Hardened.
Nitrex™ (HRC-60) available for every punch in the tooling range at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
88° SASH PUNCHES
88° Sash Punches
(Ear Piece
Max. = 15 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E41002
0.2
30
99.9
E41006
0.6
30
99.4
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
88° Sash Punches
(Ear Piece
Max. = 15 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E41102
0.2
30
69.9
E41106
0.6
30
69.4
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
19
90° SASH PUNCHES & 30° ACUTE-ANGLE PUNCHES
90° Sash Punches
(Ear
(Ear Piece)
Piece
Max. = 15 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E41202
0.2
30
69.9
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
30° Acute-Angle Punches
41908
41908
30mm
30mm
"H"
"H"
20mm
20mm
R 8mm
R 8mm
20mm
20mm
R
R
12mm
12mm
30°
30°
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E41908
0.8
100
104.0
(Ear Piece
18mm
18mm
Max. = 20 Ton/Metre)
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
20
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
30° ACUTE-ANGLE PUNCHES
30° Acute-Angle Punches
41908
30mm
"H"
20mm
R 8mm
20mm
(Ear Piece
Max. = 30 Ton/Metre)
R
12mm
30°
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E41315
1.5
100
102.0
E41330
3.0
100
97.7
*Note:
L
835 mm
18mm
S
415 mm
X 835 mm
SECTIONALISED
Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.
Induction Hardened.
Nitrex™ (HRC-60) available for every punch in the tooling range at additional cost.
30° Acute-Angle Punches
41908
30mm
"H"
20mm
R 8mm
20mm
R
12mm
30°
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E42610
0.8
100
65.5
*Note:
UK
Ireland
(Ear Piece
Max. = 30 Ton/Metre)
L
835 mm
18mm
S
415 mm
X 835 mm
SECTIONALISED
Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.
Induction Hardened.
Nitrex™ (HRC-60) available for every punch in the tooling range at additional cost.
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
21
60° ACUTE-ANGLE PUNCHES
60° Acute-Angle Punches
(Ear Piece
Max. = 100 Ton/
Metre)
*Note:
22
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E41440
4.8
100
66.2
E41460
6.0
100
65.0
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.
Induction Hardened.
Nitrex™ (HRC-60) available for every punch in the tooling range at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
75° PUNCHES
75° Standard Punches
(Ear Piece
Max. = 47 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E44000
0.8
100
67.6
E44001
1.5
100
67.2
E44003
3.0
100
66.2
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
75° Gooseneck Punches
(Ear Piece
Max. = 47 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E44030
0.8
50
120.0
E44031
1.5
50
119.5
E44033
3.0
50
118.6
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.
Induction Hardened.
Nitrex™ available for every punch in the tooling range at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
23
75° PUNCHES
75° Gooseneck Punches
(Ear Piece
Max. = 47 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E44020
0.8
70
90.8
E44021
1.5
70
89.5
E44023
3.0
70
88.6
*Note:
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.
Induction Hardened.
Nitrex™ (HRC-60) available for every punch in the tooling range at additional cost.
75° Narrow Punches
(Ear Piece
Max. = 12 Ton/Metre)
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
E44010
0.8
50
95.0
E44011
1.5
50
94.5
E44013
3.0
50
93.6
*Note:
24
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.
Induction Hardened.
Nitrex™ (HRC-60) available for every punch in the tooling range at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
75° PUNCHES
75° Gooseneck Punches
30mm
"H"
10mm
(Ear Piece
Max. = 47 Ton/Metre)
R
75°
CAT. NO.
R
mm
MAX. TON
PER METRE
“H”
44040
0.8
50
160.0
*Note:
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.
Nitrex™ is standard on Cat. No. E44040 only.
WT-41523
WT-41630
Flattening Punches
Cat No. 41630
Cat No. 41523
40mm
30mm
30mm
14mm
"H"
"H"
23mm
30mm
12mm
CAT. NO.
MAX. TON
PER METRE
“H”
L
835 mm
S
415 mm
41523
100
65.0
P.O.A
P.O.A
41630
100
84.0
P.O.A
P.O.A
*Note: Nitrex™ (HRC-60) available for every punch in the tooling range at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
25
MULTI RADIUS PUNCHES
Punch Bodies
CAT. NO.
Cat No. E408T40
Cat No. E408T25
PRICE
E408T25-835
E408T25-500
E408T25-300
E408T25-200
E408T25-100
E408T25-250X
E408T40-835
E408T40-500
E408T40-300
E408T40-200
E408T40-100
E408T40-250X
*Note:
Radius R15-40
Radius R8-25
Hardware included in punch bodies.
Bodies and Inserts Induction Hardened.
250 X Sectionalised to: 25,25,30,35,40,45,50.
100T/MTR ON ALL TOOLS
Punch Inserts
8
10
12.5
15
17.5
20
25
30
35
40
835
500
300
200
100
250x
E4R080-835
E4R080-500
E4R080-300
E4R080-200
E4R080-100
E4R080-250x
E4R100-835
E4R100-500
E4R100-300
E4R100-200
E4R100-100
E4R100-250x
E4R125-835
E4R125-500
E4R125-300
E4R125-200
E4R125-100
E4R125-250x
E4R150-835
E4R150-500
E4R150-300
E4R150-200
E4R150-100
E4R150-250x
E4R175-835
E4R175-500
E4R175-300
E4R175-200
E4R175-100
E4R175-250x
E4R200-835
E4R200-500
E4R200-300
E4R200-200
E4R200-100
E4R200-250x
E4R250-835
E4R250-500
E4R250-300
E4R250-200
E4R250-100
E4R250-250x
E4R300-835
E4R300-500
E4R300-300
E4R300-200
E4R300-100
E4R300-250x
E4R350-835
E4R350-500
E4R350-300
E4R350-200
E4R350-100
E4R350-250x
E4R400-835
E4R400-500
E4R400-300
E4R400-200
E4R400-100
E4R400-250x
Note: 250 X Sectionalised to: 25,25,30,35,40,45,50.
26
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
Solutions for your Euro style die needs
Wilson Tool offers a comprehensive range of European style press brake dies including
single V, double V quick change and bolt-on style, 4-V dies and many more. All dies up
to 25mm V-opening are made with our exclusive Nitrex surface enhancement as standard
and many models are held in stock for same day shipment.
QUICK CHANGE 2V DIES
Quick Change 2V Dies
Cat. No. E42000
Cat. No. E42001
90°
90°
7mm
4mm
6mm
5mm
3.5mm
46mm
13mm
13mm
R 0.4mm
(2)
R 0.6mm
(2)
13mm
13mm
15.05mm
6.5mm
6.5mm
4.5mm
R 0.4mm
(4)
46mm
10mm
15.05mm
6.5mm
34.5mm
37mm
Cat. No. E42002
Cat. No. E42003
90°
90°
14mm
8mm
18mm
12mm
8.5mm
46mm
10.5mm
7.5mm
5.5mm
R 0.5mm
(2)
R 0.8mm
(2)
46mm
R 0.5mm
(4)
13mm
13mm
13mm
13mm
15.05mm
6.5mm
6.5mm
15.05mm
39mm
45mm
Note:
28
CAT. NO.
MAX. TON
PER METRE
E42000
60
*E42001
70
*E42002
80
E42003
100
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
V-opening modifications and die relief available at additional cost.
Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
*Quick change 2V dies available in urethane. Please call our sales desk for pricing and lead time.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
QUICK CHANGE 2V DIES
46mm High Dies
45.5mm High Dies
Cat. No. E42008
Cat. No. E40099
88°
88°
7mm
4mm
5mm
3.5mm
R 0.4mm
(4)
45.5mm
13mm
13mm
15.05mm
6.5mm
34.5mm
34.5mm
Cat. No. E40100
Cat. No. E42007
88°
88°
42007
6mm
46mm
42007
6mm
10mm
6.5mm
4.5mm
R 0.4mm
10mm
6.5mm
4.5mm
R 0.6mm
45.5mm
R 0.4mm
13mm
13mm
13mm
13mm
15.05mm
6.5mm
5mm
3.5mm
R 0.4mm
(4)
46mm
7mm
4mm
R 0.6mm
13mm
13mm
15.05mm
15.05mm
6.5mm
6.5mm
37mm
37mm
Cat. No. E42009
Cat. No. E40101
88°
88°
8mm
12mm
7.5mm
5.5mm
46mm
8mm
R 0.5mm
(2)
7.5mm
5.5mm
R 0.8mm
(2)
45.5mm
13mm
13mm
12mm
R 0.5mm
(2)
R 0.8mm
(2)
13mm
13mm
15.05mm
15.05mm
6.5mm
6.5mm
39mm
39mm
CAT. NO.
MAX. TON
PER METRE
E42008
60
E40099
60
E42007
70
E40100
70
E42009
80
E40101
80
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: V-opening modifications and die relief available at additional cost.
Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
29
QUICK CHANGE 2V DIES
Quick Change 2V Dies
Cat. No. 42004
12mm
18mm
8.5mm
20mm
R 0.5mm
(4)
13mm
25mm
14.5mm
9.5mm
R 0.8mm
R 0.5mm
(4)
46mm
16mm
12mm
7.5mm
10.5mm
13mm
88°
88°
14mm
46mm
Cat. No. 42006
Cat. No. 42005
88°
46mm
13mm
13mm
13mm
13mm
15.05mm
6.5mm
15.05mm
6.5mm
45mm
15.05mm
6.5mm
50mm
45.5mm
CAT. NO.
MAX. TON
PER METRE
E42004
100
E42005
100
E42006
70
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: V-opening modifications and die relief available at additional cost.
Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
Quick change 2V dies available in urethane. Please call our sales desk for pricing and lead time.
30
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
QUICK CHANGE 2V DIES
Quick Change 2V Dies With Large Shoulder Radii
Cat. No. E42010
Cat. No. E42012
90°
6mm
88°
R 1.5mm
(2)
10mm
6mm
12mm
6mm
10mm
R 2.5mm
(2)
13mm
6.5mm
88°
10mm
6mm
46mm
Cat. No. E42011
42012
10mm
R 1.5mm
46mm
46mm
13mm
15.05mm
15.05mm
6.5mm
MAX. TON
PER METRE
E42010
80
E42012
80
E42011
100
L
835 mm
13mm
15.05mm
6.5mm
40mm
CAT. NO.
R 4mm
(2)
R 3mm
(2)
13mm
13mm
40mm
15mm
10mm
R 2.5mm
13mm
20mm
50mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: V-opening modifications and die relief available at additional cost.
Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
Acute-Angle Quick Change 2V Dies
Cat. No. E42021
Cat. No. E42020
30°
30°
6mm
8mm
10mm
14.5mm
15mm
9mm
R 1mm
(4)
50mm
R 1mm
(4)
13mm
15.05mm
6.5mm
18mm
50mm
13mm
13mm
12mm
13mm
15.05mm
6.5mm
58.5mm
50mm
CAT. NO.
MAX. TON
PER METRE
E42020
30
*E42021
30
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
Note: V-opening modifications and die relief available at additional cost.
Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost .
*Quick change 2V dies available in urethane. Please call our sales desk for pricing and lead time.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
31
QUICK CHANGE 2V DIES
Quick Change 60° 2V Dies
Cat. No. E42013
Cat. No. E42014
60°
6mm
60°
8mm
10mm
6.5mm
R0.6
(2)
12mm
7.5mm
18.5mm
R1
(2)
9.5mm
R0.8
(2)
46mm
R1.2
(2)
46mm
13mm
13mm
13mm
13mm
15.05mm
6.5mm
15.05mm
41mm
6.5mm
43mm
Cat. No. E42015
60°
16mm
25mm
12mm
17mm
R1.6
(2)
R2.5
(2)
46mm
13mm
6.5mm
13mm
15.05mm
55mm
CAT. NO.
MAX. TON PER
METRE
E42013
100
E42014
100
E42015
100
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: V-opening modifications and die relief available at additional cost.
Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
32
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
BOLT-ON 2V DIES
Bolt on 90° 2V Dies
Cat. No. E42030
Cat. No. E42031
Cat. No. E42032
Cat. No. E42033
90°
90°
90°
90°
Bolt on 2V Dies With Large Shoulder Radii
Cat. No. E42040
90°
CAT. NO.
MAX. TON PER
METRE
E42030
60
E42031
60
E42032
80
E42033
100
E42040
80
L
835 mm
S
415 mm
*Note: All mounting hardware is included.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
These dies are induction hardened to 60 HRC.
Nitrex available at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
33
BOLT-ON 2V DIES
Bolt on 88° 2V Dies
Cat. No. E42037
Cat. No. E42038
Cat. No. E42039
Cat. No. E42034
Cat. No. E42035
Cat. No. E42036
88°
88°
88°
88°
88°
88°
Bolt on 88° 2V Dies With Large Shoulder Radii
Cat. No. E42042
Cat. No. E42043
Cat. No. E42041
88°
88°
88°
CAT. NO.
MAX. TON
PER METRE
E42037
60
E42038
70
E42039
80
E42034
100
E42035
100
E42036
100
E42042
80
E42041
80
E42043
70
L
835 mm
S
415 mm
*Note: All mounting hardware is included.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
These dies are induction hardened to 60 HRC.
Nitrex available at additional cost.
34
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
BOLT-ON 2V DIES
Bolt on 60° 2V Dies
Cat. No. E42045
Cat. No. E42044
60°
60°
6mm
6mm
26mm
R 0.4mm
(2)
Cat. No. E42046
60°
10mm
8mm
12mm
16mm
20mm
10mm
8mm
10mm
12mm
15mm
26mm
R 0.6mm
(2)
R 0.5mm
(2)
26mm
R 0.8mm
(2)
R 1.6mm
(2)
55mm
43mm
41mm
CAT. NO.
MAX. TON
PER METRE
E42044
60
E42045
80
E42046
20
R 2.0mm
(2)
L
835 mm
S
415 mm
*Note: All mounting hardware is included.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
These dies are induction hardened to 60 HRC.
Nitrex available at additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
35
2V DIE RAIL AND CLAMP, STACKING RAILS
2V Die Rail And Clamp
FRONT VIEW
END VIEW
Cat No. 42089/42090
Cat No. 43553
15mm
15mm
10mm
END VIEW
FRONT VIEW
15mm
15mm
15mm
15mm
CAT. NO.
DESCRIPTION
42091
Rail Clamp Assembly
42092
Hardened 2V die rail
42093
2V die rail
10mm
FRONT VIEW
FRONT VIEW
END VIEW
END VIEW
50mm
L
835 mm
S
415 mm
N/A
N/A
10mm50mm
EACH
N/A
50mm
N/A
Note: All mounting hardware is included.
Stacking Rails
Cat No. 42092
15mm
["X"]
7mm
15mm
50mm
CAT. NO.
HEIGHT RANGE
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
42091
X= .575 - 1.250
P.O.A
P.O.A
P.O.A
42092
X= 1.251 - 2.000
P.O.A
P.O.A
P.O.A
42093
X= 2.001 - 2.750
P.O.A
P.O.A
P.O.A
*Note: All mounting hardware is included.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
These dies are induction hardened to 60 HRC.
Nitrex available at additional cost.
36
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
2V DIE HOLDERS
2V Die Holders
Cat No. 43021
Cat No. 43022
39mm
Cat No. 43023
45mm
60mm
60mm
CAT. NO.
L
835 mm
S
415 mm
43021
43022
43023
39mm
45mm
[ "X" ]
[ "X" ]
60mm
60mm
*Note: 2 V die holders can be modified to convert your current
press brake to use the 2V die system.
Contact sales engineer or our sales desk.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
37
60MM QUICK CHANGE 1V DIES
Quick Change 1V Dies - 60mm High
Cat. No. E42130
Cat. No. E42132
Cat. No. E42131
30°
30°
30°
Cat. No. E42133
Cat. No. E42134
30°
30°
16mm
R3
60mm
33mm
14mm
Cat. No. E42135
Cat. No. E42136
30°
30°
20mm
25mm
R4
R4
0m
80mm
80mm
0m
40mm
42mm
14mm
CAT. NO.
MAX. TON
PER METRE
E42130
40
E42131
60
E42132
60
E42133
60
E42134
60
E42135
60
E42136
60
14mm
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Quick Change 1V Dies require die holder No. 46220/46221.
V-opening modifications and die relief available at additional cost. Contact the sales desk
for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
38
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
60MM QUICK CHANGE 1V DIES
Quick Change 1V Dies - 60mm High
Cat. No. E42160
Cat. No. E42161
Cat. No. E42162
Cat. No. E42163
Cat. No. E42164
Cat. No. E42165
60°
60°
60°
60°
60°
60°
Cat. No. E42166
60°
CAT. NO.
MAX. TON
PER METRE
E42160
60
E42161
60
E42162
60
E42163
60
E42164
60
E42165
60
E42166
60
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Quick Change 1V Dies require die holder No. 46220/46221.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
39
60MM QUICK CHANGE 1V DIES
Quick Change 1V Dies - 60mm High
Cat. No. E42821
Cat. No. E42822
Cat. No. E42823
Cat. No. E42824
Cat. No. E42825
Cat. No. E42826
Cat. No. E42827
Cat. No. E42828
Cat. No. E42829
88°
88°
88°
88°
88°
88°
88°
88°
CAT. NO.
MAX. TON
PER METRE
E42821
100
E42822
100
E42823
100
E42824
100
E42825
100
E42826
100
E42827
100
E42828
100
E42829
100
L
835 mm
88°
S
415 mm
X 835 mm
SECTIONALISED
*Note: Quick Change 1V Dies require die holder No. 46220/46221.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
40
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
60MM QUICK CHANGE 1V DIES
Quick Change 1V Dies - 60mm High
Cat. No. E42801
Cat. No. E42802
90°
Cat. No. E42803
90°
Cat. No. E42804
Cat. No. E42805
90°
CAT. NO.
MAX. TON
PER METRE
E42801
100
E42802
100
E42803
100
E42804
100
E42805
100
90°
90°
L
835 mm
S
415 mm
X 835 mm
SECTIONALISED
*Note: Quick Change 1V Dies require die holder No. 46220/46221.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
41
QUICK CHANGE 1V DIES
90° Quick Change 1V Dies - 83.5mm High
Cat. No. 42100
Cat. No. 42102
90°
90°
6mm
10mm
R 1.5mm
(2)
R 2mm
(2)
83.5mm
83.5mm
14mm
Cat. No. 42103
14mm
Cat. No. 42101
90°
90°
8mm
12mm
R 2.5mm
(2)
83.5mm
R 1.5mm
(2)
83.5mm
17mm
14mm
14mm
CAT. NO.
MAX. TON
PER METRE
42100
100
42101
100
42102
100
42103
100
LT
835 mm
ST
415 mm
XT 835 mm
SECTIONALISED
*Note: Quick Change 1V Dies require die holder No. 43030/43530.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
42
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
QUICK CHANGE 1V DIES
88° Quick Change 1V Dies - 83.5mm High
Cat. No. 42120
Cat. No. 42122
Cat. No. 42121
88°
88°
88°
8mm
6mm
10mm
R 1.5mm
(2)
R 2mm
(2)
R 1.5mm
(2)
83.5mm
83.5mm
83.5mm
14mm
14mm
Cat. No. 42104
14mm
Cat. No. 42105
88°
88°
12mm
14mm
R 2.5mm
(2)
83.5mm
R 2.5mm
(2)
83.5mm
17mm
14mm
CAT. NO.
MAX. TON
PER METRE
42104
100
42105
100
42120
100
42121
100
42122
100
18mm
14mm
LT
835 mm
ST
415 mm
XT 835 mm
SECTIONALISED
*Note: Quick Change 1V Dies require die holder No. 43030.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
43
LOW PROFILE QUICK CHANGE 1V DIES
Low Profile Quick Change 1V Dies - 30mm High
Cat. No. E42110
Cat. No. E42111
6mm
8mm
90°
90°
30mm
30mm
R 1.5mm
(2)
R 1.5mm
(2)
14mm
14mm
Cat. No. E42112
Cat. No. E42114
90°
88°
10mm
12mm
30mm
30mm
R 2mm
(2)
17mm
14mm
R 2.5mm
(2)
14mm
CAT. NO.
MAX. TON
PER METRE
L
835 mm
S
415 mm
X
SECTIONALISED
E42110
100
P.O.A
P.O.A
P.O.A
E42111
100
P.O.A
P.O.A
P.O.A
E42112
100
P.O.A
P.O.A
P.O.A
E42114
100
P.O.A
P.O.A
P.O.A
*Note: Low Profile Quick Change 1V Dies require die holder No.43030/43530.
Low Profile Quick Change 1V Dies No.E42110 to No.E42112 are available in 88˚ versions.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and
lead times.
Induction hardened.
44
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
ACUTE-ANGLE QUICK CHANGE 1V DIES
Acute-Angle Quick Change 1V Dies - 83.5mm High
Cat. No. 42200
Cat. No. 42201
Cat. No. 42202
Cat. No. 42203
Cat. No. 42204
Cat. No. 42205
30°
30°
30°
30°
30°
CAT. NO.
MAX. TON
PER METRE
42200
100
42201
100
42202
100
42203
100
42204
100
42205
100
LT
835 mm
30°
ST
415 mm
XT 835 mm
SECTIONALISED
*Note: V-opening modifications and die relief available at additional cost. Contact the
sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
45
QUICK CHANGE 75° 1V DIES
Quick Change 75° 1V Dies - 83.5mm High
Cat. No. 44200
Cat.
No. 44201
44201
75°
83.5mm
14mm
44203
75°
10mm
12mm
R 2.5mm
R 1.5mm
R 0.4mm
Cat. No. 44203
75°
6mm
3mm
83.5mm
Cat.
No. 44202
44202
75°
44200
83.5mm
14mm
R 3mm
83.5mm
17mm
19mm
14mm
Cat.
No. 44204
44204
Cat. No. 44205
75°
75°
75°
R 4mm
83.5mm
24mm
83.5mm
28mm
14mm
MAX. TON
PER METRE
44200
100
44201
100
44202
100
44203
100
44204
100
44205
100
44206
100
44207
100
75°
44207
22mm
25mm
R 4.5mm
R 5.5mm
32mm
83.5mm
36mm
14mm
14mm
CAT. NO.
Cat. No. 44207
44206
20mm
R 3.5mm
83.5mm
Cat. No. 44206
44205
16mm
14mm
LT
835 mm
ST
415 mm
14mm
XT 835 mm
SECTIONALISED
*Note: V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
46
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
QUICK CHANGE 1V DIE RAILS
For 60mm High Quick Change 1V Dies
Cat No. 46220
Cat No. 46221
CAT. NO.
MAX. TON
PER METRE
“H”
46220
100
61.5
46221
100
61.5
L
835 mm
S
415 mm
*Note: It is recommended that a clamped die rail 46221 is used for sectionalised dies.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
47
QUICK CHANGE 1V DIE RAILS AND WEDGE BLOCKS
For 83.5mm High Quick Change 1V Dies
Cat No. 43559
TOP VIEW
TOP VIEW
SIDE VIEW
SIDE VIEW
CAT. NO.
TOP VIEW
30mm
ST
415mm
43559
14.1mm
Cat No. 43030
SIDE VIEW
Cat No. 43530
28mm
22mm
30mm
1.181
(30)
60mm
14.1mm
28mm
22mm
1.102
(28)
L
835 mm
.066
(22)
2.362
(60)
60mm
CAT. NO.
.555
(14.1)
S
415 mm
43030
CAT. NO.
LT
835 mm
ST
415 mm
43530
*Note:Available with die tang. Contact the sales desk for
prices and lead times.
48
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
ACUTE-ANGLE LARGE 1V DIES
Acute-Angle Large 1V Dies
Cat. No. E42300
Cat. No. E42301
30°
30°
25mm
18mm
R 4mm
(2)
R 3mm
(2)
65mm
60mm
60mm
60mm
Cat. No. E42302
Cat. No. E42303
32mm
40mm
45°
45°
R 5mm
(2)
R 5mm
(2)
60mm
80mm
60mm
60mm
Cat. No. E42304
45°
80mm
50mm
R 6mm
(2)
95mm
CAT. NO.
MAX. TON
PER METRE
E42300
80
E42301
60
E42302
40
E42303
70
E42304
70
L
835 mm
S
415 mm
*Note: Acute-Angle Large 1V Dies may require die holder No.43040.
Check height against machine stroke prior to ordering.
60mm
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
95mm
Induction hardened.
Nitrex™ (HRC-60) is available for these dies at an additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
49
LARGE 1V DIES
Large 1V Dies
Cat. No. E42400
Cat. No. E42401
85°
85°
40mm
32mm
R 4mm
(2)
R 4mm
(2)
60mm
60mm
60mm
60mm
Cat. No. E42402
Cat. No. E42403
85°
85°
63mm
50mm
R 5mm
(2)
R 4mm
(2)
75mm
60mm
60mm
60mm
80mm
CAT. NO.
MAX. TON
PER METRE
E42400
100
E42401
100
E42402
100
E42403
100
L
835 mm
S
415 mm
*Note: Large 1V Dies may require die holder No.43040.
Check height against machine stroke prior to ordering.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
Induction hardened.
Nitrex™ (HRC-60) is available for these dies at an additional cost.
50
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
LARGE 1V DIES
Large 1V Dies
Cat. No. E42404
85°
80mm
R 6mm
(2)
95mm
60mm
95mm
Cat. No. E42405
85°
100mm
R 7mm
(2)
110mm
60mm
120mm
CAT. NO.
MAX. TON
PER METRE
E42404
100
E42405
100
L
835 mm
S
415 mm
*Note: V-opening modifications and die relief available at additional cost.
Contact the sales desk for prices and lead times.
Induction hardened.
Nitrex™ (HRC-60) is available for these dies at an additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
51
LARGE 1V DIES
Large 1V Dies
125mm
R 9mm
(2)
Cat. No. E42406
80°
R 123mm
90mm
154mm
CAT. NO.
MAX. TON
PER METRE
E42406
100
L
835 mm
S
415 mm
*Note: Large 1V Dies may require die holder No.43040. Check height against machine stroke prior to ordering.
Please check width of lower beam of press brake prior to ordering die No.42406.
V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.
Induction hardened.
Nitrex™ (HRC-60) is available for this die at an additional cost.
Large 1V Die Holders
H
60mm
52
CAT. NO.
“H”
43040
50
43041
55
UK
Ireland
L
835 mm
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
S
415 mm
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
4V DIES
4V Dies
85° V50 V35 V22 V16
42341L & 42341S
85° V50 V35 - 88° V22 V16
42340L & 42340S
60° V35 V22 V16 V 10
42342L & 42342S
CAT. NO.
DESCRIPTION
42340L
4V die 88° V16 & V22 - 85° V35 & V50
42340S
4V die 88° V16 & V22 - 85° V35 & V50
42341L
4V die 85° V16, V22, V35, V50
42341S
4V die 85° V16, V22, V35, V50
42342L
4V die 60° V10, V16, V22, V35
42342S
4V die 60° V10, V16, V22, V35
PRICE
*Note: Induction hardened.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
53
QUICK CHANGE RAIL STYLE FLATTENING DIE,
3V HEMMING DIE & FLATTENING DIE
Quick Change Rail Style Flattening Die
50.0mm
14.5mm
15.05mm
50mm
*Note:
CAT. NO.
MAX. TON
PER METRE
42312
100
LT
835mm
ST
415mmv
XT 835mm
SECTIONALISED
Designed to run with standard 2V Quick Change die system.
Custom heights available for stage bending. Contact the sales desk for pricing and lead times.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
3V Hemming Die
6mm
R 1mm
(2)
12mm
10mm
60mm
R 1mm
(2)
R 1mm
(2)
60mm
CAT. NO.
MAX. TON
PER METRE
42310
100
LT
835 mm
ST
415 mm
*Note: Nitrex™ (HRC-60) is standard on the dies on this page at
no additional cost.
Flattening Die
104.4mm
79mm
96mm
60mm
CAT. NO.
MAX. TON
PER METRE
L
835 mm
S
415 mm
42311
100
P.O.A
P.O.A
*Note: Nitrex™ (HRC-60) is standard on the dies on this page at
no additional cost.
54
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
HEMMING DIES
Hemming Dies
Cat No. 42601
Cat No. 42602
16mm
16mm
R 1mm
(2)
R 1mm
(2)
R 1mm
(2)
23mm
23mm
31mm
124.5mm
116.5mm
116.5mm
22mm
10mm
14mm
8mm
14mm
6mm
Cat No. 42603
16mm
Part No.43522
Part No. 45323
60mm
60mm
60mm
Replacement V-Blocks for Wilson Hemming Dies
Cat No. 42608
Cat No. 43523
Cat No. 43522
Part No. 45324
16mm
16mm
14mm
6mm
14mm
8mm
23mm
.906
[ 23 ]
23mm
Cat No. 43524
Cat No. 43528
16mm
10mm
10mm
22mm
CAT. NO.
MAX. TON
PER METRE
MAX MATERIAL
C.R.S
42601
67
1.0 mm
42602
67
1.2 mm
42603
67
1.5 mm
42608
67
2.0 mm
43522
67
1.0 mm
43523
67
1.2 mm
43524
67
1.5 mm
43528
82
2.0 mm
31mm
LT
835 mm
43.7mm
R3
ST
415 mm
*Note: Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
55
2 STAGE HEMMING SET
2 Stage Process
- Note: 1.6mm Maximum Material
Max Ton
per metre
= 67
Max Ton
per metre
= 100
Stage 1
Stage 2
Punch Only
Cat. No. 41909
104mm
30°
10mm
R1
100mm
Die Only
Cat. No. 43595
60mm
56
CAT. NO.
DESCRIPTION
41909
Punch Only
43595
Die Only
UK
Ireland
LT
835 mm
ST
415 mm
XT 835 mm
SECTIONALISED
N/A
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
URETHANE HOLDERS
Urethane Holders
Cat No. 42502
Cat No. 42501
50mm
30mm
43mm
100mm
60mm
Cat No. 42503
80mm
60mm
91mm
Cat No. 42504
83mm
110mm
60mm
120mm
108mm
60mm
150mm
CAT. NO.
L
835 mm
S
415 mm
42501
42502
42503
42504
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
57
URETHANE PADS
Urethane Pads
Cat No. 42511 and 42521
Cat No. 42512 and 42522
25mm
50mm
30mm
50mm
Cat No. 42514 and 42524
Cat No. 42513 and 42523
30mm
45mm
80mm
110mm
CAT. NO.
SHORE
HARDNESS
42511
80A / Red
42521
90A / Blue
42512
80A / Red
42522
90A / Blue
42513
80A / Red
42523
90A / Blue
42514
80A / Red
42524
90A / Blue
L
835 mm
S
415 mm
BLUE: Best choice for general use as it is stronger and more durable
RED: Best choice when bending force is primary concern
To obtain maximum life out of urethane pad the penetration of material into the pad should never exceed 37% of pad
thickness
58
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
PART NO.43100
PART NO. 43102
RAIL STYLE OFFSET TOOLS
5.118
[ 130 ]
PART NO. 43101
Rail Style Offset Tools
Assembly Cat No. 43101
Assembly Cat No. 43100
Assembly Cat No. 43102
these are the right size
Punch
43537
Punch
43535
Punch
43533
*
*
*
94mm
**
Part No. 43103
**
Part No. 43104
3.18mm
Part No. 43105
6.4mm
4.8mm
Die
43538
Die
43536
Die
43534
Assembly Cat No. 43104
Assembly Cat No. 43103
EXTRA PARTS
91.76mm
92.88mm
Punch
43539
Assembly Cat No. 43105
Punch
43541
*
Punch
43543
*
*
89.51mm
90.65mm
88.39mm
**
**
Part No. 43106
7.9mm
9.52mm
Die
43540
11.1mm
Die
43542
Die
43544
Assembly Cat No. 43106
Punch
43545
*
87.27mm
12.7mm
CAT. NO.
MAX. TON
PER METRE
MAX. MATERIAL
C.R.4.
LT
835 mm
ST
415 mm
XT 835 mm
SECTIONALISED
43100
100
1.0mm
P.O.A
P.O.A
P.O.A
43101
100
1.0mm
P.O.A
P.O.A
P.O.A
43102
100
1.0mm
P.O.A
P.O.A
P.O.A
43103
100
1.5mm
P.O.A
P.O.A
P.O.A
43104
100
1.5mm
P.O.A
P.O.A
P.O.A
43105
100
1.5mm
P.O.A
P.O.A
P.O.A
43106
100
1.5mm
P.O.A
P.O.A
P.O.A
Note:
Die
43546
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
* Dimensions are for shut height requirements less material thickness.
** Offset height may vary as much as +- 0.5mm after bending. All angles will be obtuse.
Special offset sizes are available at additional cost.
Nitrex™ (HRC-60) is standard on the dies on this page at no additional cost.
email:
pb.sales@wilsontool.eu.com
59
ACCESSORIES
Side Gauge and Protractor Assembly & Accessories
1V Die Stabilizer
Cat No. 42704
2V Die Stabilizer
Cat No. 42705
CAT. NO.
PRICE
42704
P.O.A
42705
P.O.A
Quick Change Back Gauge Stopper Plate
Adjustable Back Gauge Stopper Plate
Cat No. 42703
CAT. NO.
PRICE
42703
P.O.A
42707
P.O.A
42708
P.O.A
42709
P.O.A
42712
P.O.A
*Note: Quick Change Back Gauge Stopper Pads are for Amada Style Back Gauges.
60
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
ACCESSORIES
Squaring Arm
The Wilson Squaring Arm from Wilson Tool Press Brake is a flexible tool enabling you to get more parts through
your Press Brake with a high accuracy.
•
Available for RH or LH loading parts
•
Simple and quick to fit
•
Can be used for bending parts at an angle
•
Makes bending small parts much easier and safer
•
Can be used as end stop for Z bends
CAT. NO.
PRICE
R/H 47000
L/H 47001
Urethane Rolls/Fabric Rolls
For Mark-Free Bending
Cat No. 42530 & 42531
Cat No. 55317 & 55318
CAT. NO.
DIMENSIONS
42530
0.4 x 152
42531
0.8 x 152
55317
100 mm x 5 m
55318
100 mm x 10 m
PRICE
*Note: Urethane dies are also available for mark-free bending.
Contact the sales desk for prices and lead times.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
61
ACCESSORIES
Side Gauge
CAT. NO.
PRICE
42701
P.O.A
*Note: Intended for use with Quick Change, 2V, Sectionalised 2V, and Quick Change 1V Dies.
Digital Protractors
CAT. NO.
DESCRIPTION
972632
Measuring 100mm
972633
Measuring 200mm
972634
Measuring 300mm
972635
Protractor Set
PRICE
Set consists of 1-off 100mm, 1-off 200mm, 1-off 300mm.
62
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
NARROW PUNCH HOLDERS
Narrow Punch Holders
Part No. 43000
Part No. 43000
7mm
7mm
Z1 Cat No. 43000
130mm
130mm
100mm
100mm
50mm
50mm
Part No. 43001
Part No. 43001
21mm
21mm
Z2 Cat No. 43001
150mm
150mm
120mm
120mm
50mm
CAT. NO.
50mm
50 mm
43000
43001
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
63
DEEP PUNCH HOLDER
Deep Punch Holder
Part No. 43002
Z2 Cat No. 43002
21mm
(Z1 version is available on
request)
250mm
220mm
CAT. NO.
DESCRIPTIONDESCRIPTION
43002
Z2 deep punch holder 150mm wide
150 mm
Note: Please consult the sales desk prior to ordering.
64
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
EUROPEAN DIE HOLDERS
European Die Holders
Cat No. 43006
39mm
60mm
43016
Cat No.
43016
50.8mm
60mm
CAT. NO.
L
835 mm
S
415 mm
43006
P.O.A
P.O.A
43016
P.O.A
P.O.A
*Note: Please contact the sales desk for a list of information that will be required prior to ordering.
Solid piece made to length for bed of press brake. Please verify press brake tongue slot width when ordering.
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
65
WILSON PRESS BRAKE TOOLING CABINET
Wilson Press Brake Tooling Cabinet - With Inserts
Standard Depth
XSC311
XSC511
XSC512
660w x 1050d x 1240h
1040w x 1050d x 1240h
1040w x 1050d x 2140h
3 vertical drawers
Qty 9 XDI102 inserts
5 vertical drawers
Qty 15 XDI102 inserts
5 vertical drawers
Qty 20 XDI102 inserts
Qty 10 XDI401 inserts
Capacity approx 16m of
bending tools
Capacity approx 26m of
bending tools
Capacity approx 34m of
bending tools
Cat. No. 55130
Cat. No. 55131
Cat. No. 55132
Extended Depth
66
XSC321
XSC521
XSC522
660w x 1300d x 1240h
1040w x 1300d x 1240h
1040w x 1300d x 2140h
3 vertical drawers
Qty 9 XDI103 inserts
5 vertical drawers
Qty 15 XDI103 inserts
5 vertical drawers
Qty 20 XDI103 inserts
Qty 10 XDI402 inserts
Qty 1 XDI216 insert
Capacity approx 20m of
bending tools
Capacity approx 33m of
bending tools
Capacity approx 44m of
bending tools
Cat. No. 55293
Cat. No. 55133
Cat. No. 55134
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
WILSON PRESS BRAKE TOOLING CABINETS
Wilson Press Brake Tooling Cabinet - Without Inserts
Standard Depth
XSC311
XSC511
XSC512
660w x 1050d x 1240h
1040w x 1050d x 1240h
1040w x 1050d x 2140h
3 vertical drawers
5 vertical drawers
5 vertical drawers
Cat. No. 55125
Cat. No. 55164
Cat. No. 55165
Extended Depth
UK
Ireland
XSC321
XSC521
XSC522
660w x 1300d x 1240h
1040w x 1300d x 1240h
1040w x 1300d x 2140h
3 vertical drawers
5 vertical drawers
5 vertical drawers
Cat. No. 55292
Cat. No. 55128
Cat. No. 55129
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
67
CABINET DRAWER INSERTS
Wilson Press Brake Tooling Cabinet - Drawer Inserts
XDI102
XDI103
For approx. 1.7 metres of tools
For approx. 2.2 metres of tools
Cat. no. 55141
Cat. no. 55142
XDI401
XDI402
Tray for storing boxes
Tray for storing boxes
Cat. no. 55208
Cat. no. 55209
Perforated Panel for Tool Storage etc
Cat. no. 55216
68
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
NOTES
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
69
INDEX
Standard Punch & Die Lengths.......................................... 5
Hemming Dies.................................................................. 55
Quick Reference Chart ...................................................6-8
2 Stage Hemming Set...................................................... 56
Express Clamping System................................................. 9
Urethane Holders............................................................. 57
European Punch Holders................................................. 10
Urethane Pads.................................................................. 58
88° & 90° Standard Punches............................................ 12
Rail Style Offset Tools....................................................... 59
88° & 90° Standard Punches with Thin Tip...................... 13
Quick Change Back Gauge Stopper Pads...................... 60
88° Gooseneck Punches.............................................14-15
Side Gauge...................................................................... 60
88° & 90° Gooseneck Punches with Thin Tip................... 16
Squaring Arm................................................................... 61
85° & 90° Gooseneck Punches........................................ 17
Urethane Rolls/Fabric Rolls.............................................. 61
88° & 90° Narrow Punches............................................... 18
Digital Protractors............................................................. 62
88° Sash Punches............................................................ 19
Narrow Punch Holders..................................................... 63
90° Sash Punches............................................................ 20
Deep Punch Holder.......................................................... 64
30° Acute-Angle Punches...........................................20-21
European Die Holders...................................................... 65
60° Acute-Angle Punches................................................ 22
Tooling Cabinet............................................................66-68
75° Punches................................................................23-25
Notes...........................................................................69-70
Flattening Punches........................................................... 25
Air Bending Force Chart (Metric)..................................... 71
Multi Radius Punches....................................................... 26
Quick Change 2V Dies................................................28-32
60° Quick Change 2V Dies.............................................. 32
Bolt on 2V Dies............................................................33-35
Stacking Rails & 2V Die Rail and Clamp.......................... 36
2V Die Holders................................................................. 37
Quick Change 1V Dies................................................38-46
75° Quick Change 1V Dies.............................................. 46
Quick Change 1V Die Holder and Wedge Block........47-48
Acute-Angle Large 1V Dies.............................................. 49
Large 1V Dies..............................................................49-52
Large 1V Die Holder......................................................... 52
4V Dies............................................................................. 53
3V Hemming Die.............................................................. 54
Flattening Die................................................................... 54
Quick Change Rail Style Flattening Die........................... 54
70
UK
Ireland
Tel (Free): 0800 012 1475
Tel (Free): 1-800 709 009
Fax (Free): 0800 012 1476
Fax (Free): 1-800 535 538
email:
pb.sales@wilsontool.eu.com
STANDARD FORMULAS FOR SELECTING A V-OPENING
MATERIAL THICKNESS: 2.6mm OR LESS = T x 6
3.0mm - 8.0mm = T x 8
9.0mm - 12.0mm = T x 10
14.0mm & THICKER = T x 12
AIR BENDING FORCE CHART
METRIC
4.2
6
1.2
4.9
7
1.3
5.6
8
1.7
7.0
10
2.0
8.6
12
2.3
10.1
14
2.7
11.5
16
3.0
13.0
18
3.3
14.4
20
3.7
*15.8
22
4.2
18.0
25
5.3
24.0
32
6.7
30.0
40
8.3
37.5
50
10.5
47.3
63
13.3
60.0
80
16.7
75.0
100
20.8
96.3
125
26.7
123.2
160
33.3
154.0
200
41.7
192.5
250
IR
4
1.0
MF
2.8
2.8
T
MF
V (mm)
0.7
4.2
V
IR
4.5
V
THICKNESS
0.5mm
6.0
NOTE: The above formulas are for reference only. For more specific information, please refer to the chart below. Chart below is for mild steel.
0.6mm
•
3.3
3.2
5.5
6.6
4.4
7.5
8.8
7.0
8.4
7.7
5.6
10.8
8.8
9.0
13.2
9.8
7.2
14.0
12.6
12.7
14.0
11.0
15.4
14.4
16.5
14.0
12.5
14.3
10.0
16.1
18.2
16.0
18.4
20.8
11.2
20.7
23.4
18.0
23.0
26.0
14.4
25.3
28.6
17.6
14.0
21.0
14.4
18.0
22.4
15.8
27.0
21.9
28.8
28.0
20.3
31.9
35.0
22.0
28.53
38.5
28.1
22.5
28.0
26.3
36.0
35.0
45.0
45.0
36.0
55.0
28.0
31.5
24.0
37.5
40.5
72.0
31.5
45.0
54.0
99.8
56.3
52.5
63.0
84.0
137.5
43.8
70.0
84.0
112.0
118.8
72.0
90.0
108.0
144.0
176.0
175.0
270.0
225.0
Tons Per Metre x 50%
Tons Per Metre x 50%
Tons Per Metre x 100%
Tons Per Metre x 150%
IR = INSIDE RADIUS
152.0
56.0
54.0
MF = MINIMUM FLANGE LENGTH
60.0
44.0
30.0
•
35.2
V = V-OPENING
33.0
20.0
10.0
P
16.0
8.0
O
E
22.0
11.0
2.3mm
N
3.5mm
R
•
17.6
0.8mm
T
1.0mm
1.2mm
1.4mm
1.6mm
2.6mm
S
2.0mm
3.0mm
4.0mm
3.2mm
4.5mm
M
5.0mm
6.0mm
T
E
R
7.0mm
10.0mm
E
9.0mm
12.0mm
16.0mm
19.0mm
22.0mm
25.0mm
30.0mm
T = MATERIAL THICKNESS
Soft Brass
The bending force (tonnage) figures listed above are based on mild steel with a tensile strength of 45-50
Soft Aluminium
kilograms per square millimetre. To calculate the approximate bending force (tonnage) requirements for other
Heat Treated Aluminium Alloys
materials, please use the multipliers listed.
Stainless Steel
Note: * Based on bending to an included angle of 88 degrees. This dimension will increase when bending to an included angle of less than 88 degrees.
Wilson Tool International (Europe) Ltd. - United Kingdom
Stirling Road, South Marston Industrial Estate,
Swindon, Wiltshire, SN3 4TQ, United Kingdom
Tel (Free): 0800 012 1475 | Tel: +44 1793 831818
Fax (Free): 0800 012 1476 | Fax: +44 1793 831945 or 46
Email: pb.sales@wilsontool.eu.com
Wilson Tool International, Inc. - United States
Tel (Free): 800-328-9646 | Tel: 651-286-6001
Fax (Free): 800-222-0002 | Fax: 651-286-5959
Email: sales@wilsontool.com
Wilson Tool International - China
Tel: +86 21 51089638 | Fax: +86 21 64422195
Email: sales@wilsontool.cn
Wilson Tool International (Europe) Ltd. - Germany
Tel (Free): 00800-9457668665 | Tel: +49 5723 747 0
Fax (Free): 00800-945766329 | Fax: +49 5723 747 10
Email: verkauf@wilsontool.eu.com
Wilson Tool International A/S - Denmark
Tel (Free): 80 20 20 24 | Tel: +45 44 53 1699
Fax (Free): 80 20 20 26 | Fax: +45 44 53 0607
Email: sales@wilsontool.dk
Wilson Tool International (Europe) Ltd. - France
Tel: +33 (0) 164 13 47 80 | Fax: +33 (0) 164 13 47 81
Email: ventes@wilsontool.eu.com
Wilson Tool International - Argentina
Tel: +54 114 7634004 | Fax: +54 114 5084190
Email: ventasargentina@wilsontool.com
Wilson Tool - South Africa (Pty) Limited
Tel: +27 877 217 875 | Fax: 086 657 8629
Email: simon.penney@wilsontool.com
The Wilson Tool Company S. de R.L. de C.V. - Mexico
Tel: 52 (81) 8865-4820 | Fax: 52 (81) 8865-4599
Email: americalatina@wilsontool.com
Exacta Precision Products - Ontario
Tel: 800-268-5573 | Fax: 800-668-9314
Email: info@exactapunch.com
Exacta FabTool - Ontario
Tel: 905-840-2240 | Fax: 905-840-1032
Email: info@exactafabtool.com
September 2014