King Air Series
Communiqué # 2016-06
June 2016
ATA 21 - Binary Switch Replacement - Air Conditioning Environmental System
BB-1978, BB-1988 and after; BL-152 and after; BY-1 and after; BZ-1 and after; FL493, FL-500 and after; FM-14 and after
The air conditioner portion of the Air Comm Corporation (formerly Keith Products) system no
longer uses individual switches for underpressure and overpressure conditions. These switches
have been replaced with a single binary switch that will interrupt power to the compressor clutch
when the system pressure is below 30 to 35 psi or above 350 psi. When the pressures stabilize,
the switch will reset itself.
If the binary switch needs to be removed, the air conditioner system does not need to be
discharged. The fitting that the pressure switch is connected to has a Schrader valve.
Unscrewing the switch from the fitting allows the technician to bench test or replace it. In the
event that the valve is replaced, the part number of the two “O” rings (preformed packing) is
ES49011-2. Replacement of the valve will require the system to be evacuated.
Issue: Initial
Page 1 of 2
Communiqué # 2016-06
ATA 21 - Air Conditioning System Plumbing Seals and Torque Values
BB-1978, BB-1988 and after; BL-152 and after; BY-1 and after; BZ-1 and after; FL493, FL-500 and after; FM-14 and after
The Air Comm Corporation (formerly Keith Products) air conditioning system uses a number of
seals throughout the plumbing. Replacement of the “O” ring seals is sometimes needed to stop
a leak or when replacing plumbing or components. The part number of the “O” ring seals and
torque values are listed below:
Recommended Fitting Torque Specifications
Caution: Torque values are for dry threads. It is recommended that torque is applied on
the low side value to prevent fitting twisting.
O-ring Replacement
1. Place appropriate sized “O” ring over the tube end of the fitting.
2. Lubricate the “O” ring with Polyolester oil viscosity ISO 68 prior to assembly.
3. Apply sealant P/N ES49000-1 to all fitting mating surfaces prior to assembly. Do not
apply sealant to the fitting threads. “O” ring part numbers follow:
Issue: Initial
Page 2 of 2
Communiqué # 2016-06
KING AIR COMMUNIQUÉ INDEX
This is a running index. Discard the old index and insert the new index.
Up thru 2016-06
ATA CHAPTER
00
DESCRIPTION
KAC No.
AIRPLANE GENERAL
Engine Start Procedures
RDO (Repair Design Office)
STARS
Log Book Bags
Year 2000 Readiness Disclosure Update
Raytheon Aircraft Publication System (REPS)
Importing and Exporting Aircraft
Factory Technical Support
Pro Line 21 Aircraft
Kit Catalogue Now on Line
Maintenance Practices for STC’s on B300
Phase Inspection Tolerance Clarification
Gravel Runway Protection Kit (2014-01)
Part Number Understanding
Passenger Briefing Cards
Communiqué CD’s
Window Stencils
Ghost “B” Paint
My Pubs Account
Emissions Trading System Scheme and Monitoring
Class Program Announcement
Volcanic Ash
Flight in Airspace w/ Low Contamination of Volcanic Ash
Emissions Trading Scheme (ETS) and Monitoring Reporting
and Verification
King Air 90 Weight Increase STC
HBC Aircraft Modified by STCs
Aircraft Data Plates
Introducing the New King Air 250
Quality Assurance Instructions (QAI)
Class Program Update
Gravel Runway Protection Kit, Rev 1
Repair Design Office Damage Report Procedures
Direct Approach Communication
Technology Briefings
King Air 200 MTOW Increase Kit
Illustrated Parts Catalogue Free of Charge
Introduction of Block Point 2015 King Air with Fusion Avionics
(See 2016-02)
FAA Flight Standardization Report (FSB) & EASA Operational
97-001
98-001
98-001
98-002
99-004
2001-03
2001-04
2003-01
2004-02
2005-02
2005-02
2006-01
2006-02
2006-02
2007-02
2008-02
2008-03
2008-03
2009-01
2009-02
2009-03
2010-02
2010-03
2010-05
2010-05
2011-04
2012-04
2012-04
2012-04
2013-01
2014-01
2014-01
2015-02
2015-03
2015-05
2016-01
2016-01
2016-02
Suitability Data (OSD)
Introduction of Block Point 2015 King Air with Fusion Avionics,
Rev 1.
04
AIRWORTHINESS LIMITATIONS
Life Limited Aircraft Parts
King Air Special Purpose Aircraft-Wing Life Evaluation
05
97-001
97-001
98-001
98-002
2001-03
2001-03
2001-03
2005-02
2006-01
2006-01
2006-02
2006-02
2008-02
2008-02
2011-03
2011-03
2013-02
2013-03
2013-04
2014-02
2016-03
Lifting and Shoring
Tail Stand Operation
11
2002-02
2015-08
TIME LIMITS/MAINTENANCE CHECKS
Phase Inspection Program
Inspection
Structural Limitations
Special Inspections Calendar Tolerance
Service Instructions’ Effectivity
Structural Inspection Interval
Special Purpose Airplanes Wing Life
Phase Inspection Tolerance Clarification
King Air Inspection “Month” Definition
Phase Inspection Tolerance Clarification
FAQ Regarding the Inspection Program
Flammable Fluid Carrying Hoses Replacement
Inspection Access (Obsolete) See 2011-03
Inspection Program Clarification
Phase 3 Inspection Access-Pilots Compartment/Cabin
Flammable Liquid Carrying Hose Kits from HBP&D (2014-02)
Aging Aircraft Inspection Program
High Utilization Inspection Program
High Utilization Inspection Program Q&A
Flammable Liquid Carrying Hose Kits From HBP&D, Rev 1
Flammable Liquid Carrying Hoses Replacement Clarification
07
2016-02
2016-04
PLACARDS
King Air Emergency Exit Placards
Engine Oil Service Placard Change
Spanish Language Placard Kits
Emergency Exit Markings, 2” Band Requirement
Interior/exterior Placards in Spanish
2000-04
2000-04
2003-01
2007-02
2014-01
12
SERVICING
Flap Motor Gear Box Lubrication
Electric Toilet Servicing
Wing Bolt Special Tool
Wing Bolt Tools
Wing Bolt Grease Gun
King Air Flap Actuator Lubrication Supercedure
King Air Lubrication: AerosShell 17 Grease
Mobile Grease SHC 100
Dow Corning #33
Grease Change
20
STANDARD PRACTICES
Paint Removal
Aromatic Polymide Wiring
Rivet Installation Criteria
Aircraft Cleaning
Paint Stripping Procedures
Gyro Handling and Packaging
Liquid Mercury Contacting Aluminum
Typical AN386 Taper Pin Installation
Ground Hazard Zone
RDO Standard Repair Index (Updated See 2011-03)
Metal Damage Assessment
King Air Wiring and Sleeve Inspection
Erosion Protection System
Standard Component Installation/Removal
Aircraft Plumbing Routing and Installation
Aircraft Inspections-Inspection of Adjacent Areas
Repair Design Office Standard Repair Index
Electrical Connectors Maintenance Practices/Contact Cleaner
Wing Locker Paint Cracking
Ground Stud Installation Tool (See 2014-01)
Ground Stud Installation Tool Rev 1
Nose Landing Gear Wheel Well Under-Coating
Leading Edge Erosion Tape
21
97-002
99-001
99-003
99-003
2001-03
2006-02
2006-02
2008-01
2008-03
2015-07
98-002
98-003
98-003
99-001
2000-03
2001-03
2003-01
2003-02
2003-03
2005-02
2006-01
2006-02
2007-02
2008-03
2009-03
2010-04
2011-03
2011-03
2011-03
2013-02
2014-01
2016-03
2016-05
AIR-CONDITIONING
Air-Conditioning Compressor Pivot Plate
Pressurization System Test Safety Belt
Air Conditioning Leaking Hoses
134a Freon Air-Conditioning Dust Caps
Aft Evaporator Plenum
Air-Conditioning “Low” & “High” Hoses Reversed
Ram Air Door Rigging
97-002
98-001
98-002
98-003
99-003
2000-03
2000-03
Insufficient Cabin Heat
Pressurization Low/Normal Switch Operation
Pressurization Leak/Landing Gear Shaft
Air Conditioner Compressor Drive
King Air Series Vapor Cycle Air Conditioning
Pneumatic Flow Control Solenoid
Air-conditioning Plumbing Seals
Pressurization Troubleshooting
Vibration/Buzz Sound Traced to the A/C Condenser Blower
Electronic Flow Control System Test Procedure
Pressurization System Rubber Tubes
Water Manometer Test Ports
New Air Conditioning Compressors Hard to Turn
King Air Cabin Barometric Switches Test Options
Vent Blower Troubleshooting Tips
Aft Evaporator Caused Bad Odor
Air-Conditioning Hoses Length Change
Air Conditioner Motor Brush Wear (EM56-2)
Air Conditioner Quill Shaft Wet/Dry Spline
Air Conditioner Flushing Procedures
King Air Air-Conditioning PC Board A130
Air-Conditioner Compressor & Mount Assembly
Bad Smell with the Air-Conditioning Running
Servicing Oil in the Air-Conditioning Systems
Air Conditioner Motor Brush Wear (ASC motor)
New Air Conditioner System Introduced
Air Conditioning Compressor Usability 90/100
Aft Ducts for Air Conditioning and Heating
Flow Control Valve Replacement & Fit-O-Seal
Keith Air Conditioning Battery Discharge
Keith Air Conditioning Battery Discharge (Revisited)
Environmental Ducts Insulation and Tape
Keith Products Environmental System/Manometer
Keith Products Environmental/Aft Evaporator Installation
Condenser Blower Keith Products Environmental System
Keith Products Cabin Evaporator Blowers Handling
Condenser Blower Inlet Kit
350i Cabin Management/Environmental System
Air Conditioner Continues to Run with Air Conditioner Mode
Switch OFF
Air Conditioning Electrical Troubleshooting
Keith Products Troubleshooting/Lap Top Set Up Information
Binary Switch Replacement- Air Conditioning Environmental
System
Air Conditioning System Plumbing Seals and Torque values
22
2000-04
2000-04
2001-01
2001-01
2001-02
2001-03
2002-03
2002-04
2002-05
2002-05
2003-01
2003-02
2003-02
2003-02
2003-03
2005-02
2005-02
2006-01
2006-01
2006-01
2006-02
2006-02
2006-02
2006-02
2007-02
2007-02
2007-02
2007-02
2007-02
2008-01
2008-03
2009-05
2010-05
2010-05
2011-03
2012-04
2012-04
2013-02
2014-02
2015-05
2015-05
2016-06
2016-06
AUTO FLIGHT
GPS/Auto Pilot Upgrade
GPS Approach Capability
97-001
97-001
APC-65H Auto Pilot Computer Enhancements
APC-65H/J Auto Pilot Computer Enhancements
Rockwell Collins Autopilot Servo
SVO-85B/85C Service Bulletin
Busing Module Issue on the Meggit Altimeter
Ground Communication
23
97-002
99-001
99-002
99-005
99-005
2000-02
2001-01
2002-01
2002-01
2002-04
2002-05
2002-05
2005-04
2006-01
2007-02
2013-02
ELECTRICAL POWER
Chafing Wire Bundle
King Air Starter Generator Ground Terminal
Dual Fed Bus Circuit Breakers
Alternate Generator Control Unit Breakout Box
Alternate Generator Control Unit Breakout Box R1
Replacement Batteries
External Power Annunciator
Electrical Load Analysis
Lead Acid Battery Replacement Kit
Generator Control Unit Part Numbers
King Air Voltage Regulators
Starter Generator and Oil Filter
Starter Generator Terminal Adapter Nuts
Starter Generator Ground Point
25
2003-02
2004-02
COMMUNICATIONS
Cockpit Voice Recorder
Torque Transmitter Change
VHF Communication-8.33 KHZ
VHF Communication 8.33 KHZ Up Date
Collins Pro Line II VHF Comm 8.33 KHZ Up Date
Elliott’s Ultra Quiet System
Elliott’s Ultra Quiet System Technical Support
BRNAV KLN-90B Service Bulletin
Proper Maintenance and Care of the Ultra Quite Sound
Management System
Ultra Quiet Speaker and Patch Cable Service Bulletin
Honeywell Service Bulletin: Enhanced GPWS
Ultra Quiet Speaker and Patch Cable Service Bulletin
Ultra Quiet System Software Maintenance Terminal
Static Wick Bonding Check
Elliott System ANVS Maintenance Terminal
Elliott Aviation Sound Management System Technical Support
24
98-002
98-002
2001-04
99-005
2000-02
2000-03
2000-03
2001-01
2001-03
2002-05
2002-05
2003-01
2003-03
2005-02
2006-01
2014-02
2015-08
EQUIPMENT/FURNISHINGS
Arm Rest Stop
Longer Seat Belts
97-001
97-002
Cabin Partition Tool
Hot Tank Lid Repair
Cabin Seat Installation
Passenger Briefing Card
Two Place Side Facing Couch and Seat Belts
ELT Batteries
Utility Covers, Crew and Cabin Chairs
Sheep Skin Crew Chair Covers
Hot Tank Assembly
Crash Axe Installation Kit
Cabin Passenger Shoulder Harness Stop Button
Aft Facing Seats Head Rest Installation and Inspec.
Seat Belt Extenders
ELT Testing
Cabin Seat Base Paint
Interior Cabinets and Tables
King Air B300 Seat Attach Hardware
Crew Seat Removal Kit
Smoking Option Aircraft
Global Engineering Cabin Table Repair Kit
Global Engineering Hot Tank Spigot Replacement
Global Engineering Divider Pivot Pin Installation
Collapsible Arm Rest Repair
Up-right Cabinet Hot Tank Slide Strips
Ottoman Installation
Cabin Chime Locations
Clarification of MSB 25-4055
Toilet Seat Bottom Cushion Release Mechanism Placard
ELT Antenna Replacement Kit
First Air Kits – Contaminated Iodine Wipes
Narco Emergency Locator Transmitter Batteries
Crew Seats Shoulder Harness Binging
26
FIRE PROTECTION
Fire Detection System Functional Test
Fire Extinguisher Relocation/Foreign Certification
King Air Flame Detectors Parts and Availability
Engine Fire Extinguisher Connections
Bleed Air Warning System Description and Troubleshooting
Bleed Air Warning Sense Line Repairs
Engine Fire Extinguisher Agents
27
2000-02
2000-02
2001-01
2001-01
2001-01
2001-03
2002-03
2002-03
2002-04
2003-01
2003-01
2003-01
2003-02
2004-02
2004-02
2005-02
2005-02
2005-02
2006-02
2007-02
2007-02
2007-02
2008-02
2009-05
2010-05
2010-05
2011-01
2011-03
2012-04
2012-04
2014-01
2014-02
97-001
2002-03
2005-02
2009-05
2013-02
2014-01
2016-01
FLIGHT CONTROLS
Elevator Trim Actuator
Rudder Torque Shaft See ATA 55
Flap Gearbox Shims
98-001
98-002
98-002
Elevator Trim Tab
Rudder Boost System and Troubleshooting
Flap Actuator Installation
Elevator Trim Actuator
Universal Travel Board See 2001-04
Flap Gear Box Grease
Rudder Boost Pneumatic Line Chaffing
Flap Roller and Washer Position 200/300 (See 2006-02 for
other models)
Rudder Boost Filter Replacement (see 2003-02)
Universal Travel Board
Service Bulletin 27-3095, “Flight Controls-Addition of Jumper
Wire to Stall Warning Lift Computer”, Serial Effectivity
Clarification
Unapproved Hardware on Primary Control Surfaces
Flap Linkage and Bracket Interference
Rudder Boost Filter Replacement and Up-grade (see 2001-01)
Flight Control Rig Pins
Aileron Installation
Horizontal Stabilizer Actuator Installation
Rudder Boost Filter Supercedure
Flap Roller and Washer Position Installation 90, Series, F90
and 100 Series (See 2000-04 for other models)
Control Wheel Grips
King Air 250 Stall Warning Calibration
Towing Aircraft with Gust Lock Installed-Consequences
Lower Attach Bolt Bent
Elevator Bob Weight Inspection
Stall Warning Vane Heat
28
98-002
98-002
98-003
99-001
99-005
2000-02
2000-04
2000-04
2001-01
2001-04
2002-01
2002-05
2003-01
2003-02
2003-02
2003-03
2003-03
2004-02
2006-02
2012-04
2014-01
2014-01
2015-01
2015-05
2015-07
FUEL
Flush Fuel Drain Valve
Biological Contamination Inspection (See also 2006-02)
Fuel Caps
Wing Tip Vent Float Valve “O” Ring Installation
Auxiliary Fuel Tank Seals
Fuel Vapor Smell in the Cabin
Defueling Valve
Airborne Fuel Boost Pumps
Fuel Flow Test Tool
New Lower Operating Pressure Fuel Cap (2007-02)
Nacelle and Auxiliary Tanks Fuel Cover Kit
Lockable Fuel Caps
Fuel Access Covers (SB-28-3401)
Fuel Quantity Indicator Bench Check
Fuel Cell Cover Assembly Part Numbers (2007-02)
Firewall Shutoff Valve Product Improvement
B200/B300 Fuel Vent System Inspection
Fuel Quantity Test Equipment
97-001
97-002
98-001
98-002
98-002
98-003
98-003
99-001
99-003
2001-01
2001-03
2001-04
2002-03
2002-05
2002-05
2003-02
2004-02
2004-02
Fuel Probe Matrix Block Tool
Firewall Fuel Filter Reset
Fuel Cell Inspection for Corrosion, Microbiological Growth (See
also 97-002)
King Air Fueling Procedures
Fuel Cells Cover Assemblies, Rev. 1 (2002-05)
New Lower Operating Pressure Fuel Cap (2001-01)
Center Section Fuel Cell Installation (dual lock fasteners)
Fuel Crossfeed Control Printed Circuit Board
Biobor JF Alternate
Fuel Wing Tip Float Valve Improvement Kit
Corrosion Preventive of Nacelle, Auxiliary Fuel Cell & Auxiliary
Fuel Cell Inboard Fuel Probe Dish, Cover and Pans
Fuel Quantity Indication System History & Test Equipment
Fuel Tank Foreign Objects
Corrosion Prevention on Nacelle, Aux. Tanks Covers
Fuel Migration-King Air 200 & 300 Series
Barfield DC-400 Operating Instructions
Improper De-Fueling Procedures Causes Nacelle Structural
Damage
Fuel Drain Inspection
Fuel Tank Access Corrosion Prevention
Fuel Quantity Indicator Connector Change-Kit 101-3111-1 S
Service Bulletin 2037 Rev 1, Correction Effectivity Listed in SB
Wet Wing Fuel Probe Harness Lock-O-Seal
30
2004-02
2005-02
2006-02
2007-02
2007-02
2007-02
2008-02
2009-05
2009-05
2012-04
2012-04
2013-02
2014-01
2014-01
2014-01
2014-02
2014-02
2015-05
2015-07
2015-08
2016-02
2016-05
ICE & RAIN PROTECTION
Stall Strip Installation (See also 2006-02)
Stall Strip Installation Correction
Engine Anti-Ice Valve Brackets and Hardware
BFG News Letter (De-Ice Boots)
Anti-Icing/Fuel
Engine Operations in Icing Conditions
Ice-Vane Door Hinge Pin Installation
Type IV De-ice Fluids Announcement
Ice Vane Door Brush Seal
Defog System Filter Installation
Window Defrost Filter Kit and Replacement Interval
Engine Inlet Discoloration
Goodrich FASTboots Installation
Engine Heated Inlet Modified per Kit 101-9048
Stall Strip Bonding Material
Stall Strip Installation, Combi-Bond (See also 97-001)
Brake De-Ice System Removal Kit (See 2014-01)
Wing De-ice Boot 3M Adhesive 1300L Sold in Europe
SMR De-Ice Boot Supplier Advisory (SA12-33-01)
Brake De-ice System Removal Kit, Rev 1
Brake De-ice System Troubleshooting
King Air 250 De-ice Boots
97-001
97-001
97-001
98-001
98-001
98-003
99-001
2000-01
2000-04
2001-01
2002-03
2002-03
2005-02
2006-01
2006-01
2006-02
2010-05
2011-03
2012-04
2014-01
2014-01
2014-01
King Air C90GTx De-ice Boots
King Air B200GT/B200CGT (250) Propeller Heat-Blade
Damage
Stall Strip Bonding Agent
31
2016-01
IND/RECORDING SYSTEMS
Flight Data Recorder
Radio Frequency Interference
Airspeed Bugs
Pitot Heat Indicator Kit
Instrument Leak Causes Pressurization Leak and Squeal
Annunciator Dimming Transistor Installation
Oil Indicator packaging
Pro-Line 21 Maintenance Diagnostic Computer; Maintenance
Diagnostic Tables and Electronic Check Lists
King Air Fusion Software Loading Equipment Requirement
(See 2016-05)
Fusion Equipped King Air Software and Database
King Air Fusion Avionics Software Loading Equipment
Requirements
Fusion Equipped King Air USB Device Requirements
32
2014-01
2015-07
98-002
99-001
2001-01
2003-01
2003-02
2003-03
2008-01
2014-01
2016-01
2016-04
2016-05
2016-05
LANDING GEAR
Wide Area Wheel Retention Washer Seal
Brake Master Cylinder Repair Kit
Valve Stem Torque, ABS Wheels
Inflation Valve Torque Procedures (BF Goodrich)
Inflation Valve Torque Procedures (ABS)
Torquing of Wheel Tie Bolts
Landing Gear Piston and Axle Assembly Leaks
Landing Gear 60 Amp Circuit Breaker Relocation
Brake De-ice Valve Installation
Hydraulic Power-pack Parts Breakdown.
See Rev. 1 on Comm. 2001-04
BF Goodrich Brake Repairs
Hydraulic Landing Gear Actuator Installation
Tire Usability (See 2003-01 for Rev 1) (2016-06 for Rev 2))
BF Goodrich Nose Wheel Torque Value Mislabel
Landing Gear Torque Knees
Bumper Block Installation. See ATA 54
Nose Landing Gear Actuators Swivel Parts. (See 2005-02)
Main Landing Gear Side Brace Crack
Aircraft Steering
Exceeding Aircraft Turning Limits
Landing Gear Actuator Clevis Limits and Part Numbers. See
2002-03 for Rev. 1.
Hydraulic Power-pack Parts Breakdown. Rev. 1 (99—003)
97-001
97-002
98-001
98-002
98-002
98-003
99-001
99-001
99-001
99-003
99-003
99-003
99-005
2000-03
2000-03
2000-04
2000-04
2000-04
2001-01
2001-01
2001-03
2001-04
Foot and Mouth Disease, Wheel and Brake Components
Nose Landing Gear Fork Assembly Replacement
Landing Gear Power Pack Motor Wiring
Landing Gear Actuators End Play Check
Landing Gear Actuator Clevis Wear Limits and Part Numbers.
Rev. 1 (See 2001-03)
Accelerated Wear of Brake Assemblies
SB 32-2102 and 53-2472 up coming revisions
King Air C90A Tires
Brake Reservoir
Nose Landing Gear Scraper and Wiper Ring Installation Hints
Hi-Flotation Landing Gear Wheel Service Bulletin from ABS
Tire Usability. Rev 1 (99-005) (2016-06)
Hydraulic Landing Gear Actuator Restrictors
Nose Wheel Spares
Nose Landing Gear Actuator Swivel Parts Breakdown. See
2000-04
Wheel and Brake Cross-over Part Numbers
Nose Landing Gear Actuator Swivel Parts Rev. 1 (See 2000-04)
Landing Gear Inspection vs. Overhaul
Landing Gear Grease Gun Modification
Nose Landing Gear Stop Block Installation
Cycling of Hydraulic Power Packs
King Air Overhaul vs. Inspection in Landing Gear CMM
Landing Gear Attach Hole Inspection
Hydraulic Plumbing Replacement Procedures
Tire and Brake STC Comparability Issue
King Air 100 Tire Usage
CMM Index
Landing Gear Attach Hole Inspection
Brake Overhaul Kit
Main Landing Gear Tires, King Air 90 Series
Landing Gear Seals Parts List
Landing Gear RCCB Installation Kit
MSB 32-3345 Compliance Reminder
Wheel Eddy Current Inspection Probes
Tire Usability Rev 2
Main Landing Gear Leg “Un-Locking” After Extension
33
2001-04
2001-04
2002-01
2002-03
2002-03
2002-03
2002-04
2002-05
2003-01
2003-01
2003-01
2003-01
2003-02
2003-02
2005-02
2005-02
2005-02
2005-02
2006-01
2006-01
2006-02
2006-02
2006-02
2006-02
2007-02
2008-01
2008-02
2008-03
2009-01
2009-05
2011-03
2012-04
2014-01
2014-01
2016-04
2016-05
LIGHTS
Cabin Indirect Lighting
Cabin Indirect Lighting
Cold Cathode Connector Assembly & Potting Instr.
Rotating Beacon Replacement (See 2006-01)
Wing Tip Navlight Lense Installation
Fluorescent Light Power Supplies
Recommended SB 33-3410, Flashing Beacon Hardware Kit
Wing High Intensity Nav Light Bulb Replacement
Flashing Beacon Light Bulb Replacement
98-001
99-005
2000-03
2001-04
2001-04
2002-01
2002-05
2003-02
2003-02
King Air Landing and Taxi Lights Kits
Rotating Beacon Replacement (2001-01 Rev. 1)
Overhead Panel Transistor Layout
Cold Cathode Lighting Systems
Smoking Option Aircraft
Fluorescent Power Supply Replacement
Cold Cathode Lighting Power Supplies
LED Taxi Landing Lights Kit
34
NAVIGATION/PITOT STATIC
AlliedSignal GPS Receiver Software Bulletin
Standby Power Supplies
Revised Copilot Side Gyro Horizon Part Numbers
Standby Compass Calibration
Cockpit Voice Recorder Installation Kit
ProLine 21 Electronic Check List
King Air Meggitt Altimeters Issues
Elementary and Enhanced Mode S Transponders
EGPWS Terrain Database Subscriptions
MMEL RVSM Revisions
Clarification of FAA Advisory Circular AC 90-100
RVSM Instructions for Initial and Continued Airworthiness
Pro Line 21 24 Month ADC-3000 and ESIS GH-3100 91.411
Recertification
FAA Special Airworthiness Information Bulletin CE-10-14
TDR-94/TDR-94D Mode S Transponders Installed Without
TCAS II
Universal Avionics Navigation Database, Magnetic Variation &
System Support Updates
TCAS 4000 Update to Software Version 7.1
ProLine 21 FMC & MDC Battery Life
FAA AD 2014-18-01 on TDR 94/94D Transponders
Reduced Vertical Separation Minimum
ACSS TAWS+ System Override Mode Operation
ProLine 21 King Air Reduced Vertical Separation Minimum
(RVSM) with Automatic Dependent Surveillance-Broadcast
(ADS-B) Out Transponder Installed
35
2005-02
2006-01
2006-01
2006-01
2006-02
2011-02
2012-04
2015-01
98-003
99-001
2001-01
2002-03
2003-01
2004-03
2004-04
2005-01
2005-02
2005-02
2005-03
2007-01
2009-05
2010-01
2012-02
2012-04
2012-04
2012-04
2014-02
2015-04
2015-07
2016-03
Oxygen
Oxygen Valve Manual Override Location (B300)
Oxygen Leak Detection Equipment
Oxygen Mask Container Door Part Numbers
Passenger Oxygen Mask Packing
Oxygen System Barometric Switch Moisture
Passenger Oxygen Mask Manual Over-Ride “O” Ring
Replacement
Oxygen Masks Quick Donning Replacement Kits
98-003
99-001
99-001
99-005
2000-02
2006-01
2006-02
Oxygen Cylinder Assembly P/Ns vs. DOT Cross Reference
Chart
38
Water/Waste
Relief Tube Installation
Toilet Blue Water
44
2013-02
DOORS
King Air Cabin Door Warning Switch Striker Plate
Air Stair Door Panels, Improved
Air Stair Door Lower Latch Pins, Change
Cabin Door Hinge Break Down
Cabin Door Latch Bolts Green Indicator Tape
Cabin Door Placard Installation, SB 52-3096
Cabin Airstair Door Latch Bolt Kits
Cabin Door Upper Hook Mechanism and Latch Bolt Kits
Cabin Door Lock Keys
Keyed Lock Replacement on Emergency Exits
Air-Stair Door Hinge Lug Limitation
Cabin Door Warning Switch Striker Plate Spring (98-001 Rev.1)
King Air Cabin Door Closing Procedures
Door Handle Lock Changing Procedure
Medeco Door Handle Installation
Medeco Door Handle Removal
Emergency Exit Skin Cracks
Cabin Door Hook Mechanism Kit
Cabin Door Roller Assembly
Cabin Door Lighted Folding Steps
53
98-003
2012-04
Cabin Systems
350i Venue Cabin Management System Software Version 3.0
Service Bulletin
52
2011-03
98-001
2001-03
2001-03
2001-04
2002-03
2002-04
2002-04
2003-01
2003-01
2006-01
2006-01
2006-01
2007-02
2008-03
2009-01
2009-01
2010-05
2012-04
2013-02
2014-01
FUSELAGE
Avionics Nose Door, Ice Protection
Fuselage Skin Cracks Repair Kit
Aft Fuselage Drain Tube
Fuselage Cross-Tie Cracks
Nose Bay Water Ingression
Entry Door Floorboard Assembly (See also 2013-02)
Fuselage Rivet Sealing Procedure
SB 32-2102 and 53-2472 up coming revisions
“Lower Skin Rumble” Kit for C90B
Evaporator Cover Panel Gasket
97-001
98-001
99-001
2000-02
2000-04
2000-04
2002-03
2002-04
2003-01
2003-02
Pressurization Leaks/Stringer Seal
Fuselage Structural Inspection Report
Fuselage Repair, Skins
Cross Tie Inspection
Entry Door Floorboard Assembly (See also 2000-04)
54
NACELLES/PYLONS
Inlet Duct Skin Repair
Bumper Block Installation (2014-02)
Cowling Fixed Vane Assembly
Engine Anti-Ice Inlet Installation
Drag Leg Attach Fitting Crack
Bumper Block Installation, Rev 1
55
99-005
2000-04
2001-01
2001-01
2002-03
2014-02
STABILIZERS
SB 2422, Rev.1. Rudder Torque Shaft
Horizontal Stabilizer Aft Pivot
Elevator Torque Tube Assembly
Empennage Inspection Panel Kit
Horizontal and Vertical Stabilizer Inspection Limitation
Vertical Stabilizer Front Spar Cap Angles Cracks
Horizontal/Vertical Stabilizer Inspection Panel Kits from Third
Party Vendors
56
2003-02
2004-02
2006-01
2011-03
2013-02
98-002
99-003
99-003
2008-01
2012-01
2012-03
2012-04
WINDOWS
Windshield Performance Data
PPG’s “Surface Seal”
Windshield “Hump” Seal (See 2010-05) (2013-02)
Window Seal Creeping
Windshield “Surface Seal Kit” (See 2002-03)
Windshield Hump Seal Temporary
Windshield Cleaning
Cockpit and Cabin Windows
Repaired King Air Windshields
New and Improved Storm Window Seal
Windshield Surface Seal
Windshield Screw Replacement Kit
Polarized Window Knob
Windshield Delamination
Windshield Sealant Alternatives
Cabin Window Seals
King Air Windshield Supercedure History
King Air Windshield Anti-Static Coating
Windshield Cleaning
Side Windows Inspection Actions
97-002
97-002
98-001
98-001
98-002
98-002
99-005
99-005
2000-02
2001-03
2002-03
2003-01
2003-01
2003-01
2004-02
2004-02
2005-02
2005-02
2006-01
2007-02
Storm Window Seal Installation (See 2009-05)
Storm Window Seal Installation, Kit Announcement
Hump Seal Kit Not Longer Available (See 2013-02)
Windshield Hump Seal Kit Available Again
Windshield Electrical Connections
Windshield Electrical Connections Screw Torque
Windshield Electrical Connections Miswired
57
WINGS
Wing Attach Drain Holes
Air to Air Heat Exchanger Duct Assembly
Battery Access Door Air Scoop
Wing Trailing Edge Cracks
Auxiliary Tank Upper Panel Insert Replacement
Auxiliary Tank Upper Panel Insert Replacement R1
SIRM Inspection
SIRM Inspection, Rev. 1
Lower Forward Wing Bolt Kit
Wing Bolt Covers
SIRM Training Requirements
SIRM Lower Forward Fitting Inspection
Wing Center Section Upper Wing Panel Debond
Aft Spar Lower Cap Inspection-SIRM
Outboard Wing Structure Lower Forward Spar Cap
Replacement
S.I.R.M. Lower Fitting Initial Inspection Interval Addition- F-90
Wing Structure Inspection Training Course
King Air Wing Bolt Kits
Flap Cove Spot Welds
F-90 wing bolt kit (correction to 2007-02)
Upper Forward Wing Bolt Change
Wing Bolt Cover Plate Part Number
Wing Inspection per AD 89-25-08 and 89-25-10
Upper Aft Wing Bolt Cover Improvement Kit
Wing Lockers Service Bulletin From Raisbeck
Wing Bolt Cover Sealing
61
2008-02
2009-05
2010-05
2013-02
2016-04
2016-04
2016-04
99-001
99-001
99-001
99-005
2000-03
2001-01
2001-01
2001-03
2003-01
2003-02
2004-02
2004-02
2004-02
2005-02
2005-02
2006-01
2006-02
2007-02
2007-02
2008-02
2009-01
2010-05
2011-03
2012-04
2014-02
2014-02
PROPELLERS
Woodward Governor Company Service Bulletin
McCauley Service Letter 1998-7
Woodward Governor Company Service Bulletin
Propeller Governors and Sudden Engine Stoppage
Hartzell Four Bladed Prop Feather Blade Angle Adj.
Propeller Balance
Four Bladed Propellers on King Air C90A
Autofeather Flashing Lights
Hartzell Propeller Service Bulletin Mounting Bolt Inspection
98-002
98-003
99-005
2000-04
2001-01
2001-03
2001-03
2001-04
2002-04
Hartzell Propeller Grease Over-Servicing
Auto-feather System Troubleshooting, Engines Off
Torque Manifold Bleeding Procedures
Propeller Synchrophaser Target Installation (F90)
Propeller to Prop Shaft “O” Ring for Hartzell Propellers
Synchrophaser Pickup Gap (200 Series)
Ground Idle Solenoid Installation & Maintenance F-90
Hartzell Counterweight Slug Bolts
Four-Bladed Propellers Reaction less Mode Resonant Vibration
Ground Idle Stop Solenoids Drop Off Line During Engine Start
Propeller Synchronization Test Equipment for Rent
King Air C90GTx Swept Blade Propellers
71
POWER PLANT
Engine Vibrator Isolators
Engine Fuel Pump Inlet Filter
Handling Pneumatic P3 and PY Lines
ITT Harness
Engine Fuel Pump Inlet Filter
Engine Compressor Wash Ring Kit
Engine Compressor and Turbine Washing
Engine Truss Paint
P&WC S.I.L.- Fuel Control Unit Health Monitoring
Engine Isolator Mounts-TBO
73
2002-01
2003-02
2003-03
2008-02
2015-06
IGNITION
Engine Ignition (90/100 Series)
T5 Thermocouple Wiring Terminal
Ignition Exciter Box Spares Replacement
76
97-002
97-002
2001-01
2001-04
2002-04
2003-01
2003-01
2006-02
2014-02
2015-05
ENGINE FUEL and CONTROL
Engine Driven Low Pressure Fuel Pump
Engine Driven Low Pressure Fuel Pumps
Garrett Engines Service Bulletin TPE331-2102
C90GT P3 Filter
Fuel Control Unit Inspection
74
2003-01
2005-02
2006-02
2006-02
2006-02
2007-02
2007-02
2008-03
2011-05
2012-04
2015-01
2015-08
98-003
99-001
2004-02
ENGINE CONTROLS
McCauley 4 Blade Flight Idle Low Pitch Chart
Correcting Throttle Backlash
Fuel Control Arm Installation Orientation
2000-04
2008-02
2015-07
77
ENGINE INDICATING
ITT Analog to Digital Change
Power Check
Meggitt Torque Indicator Replacement and Calibration
ITT Calibration Checks
Torque Indication Calibration C90GT
ProLine 21 Aircraft Engine Indicating System Operation and
Troubleshooting
78
EXHAUST
Exhaust Stack Fairings Camloc
Exhaust Stack Material and Welding Specifications
Exhaust Stack Flex Tubes, STC
King Air B100 Exhaust Pipe Insulating Blanket
Exhaust Stack Fairing Installation
Exhaust Stack Fairing Product Improvement
79
98-002
2003-01
2004-02
2005-02
2009-05
2014-01
Oil
Oil Pressure Slow to Register
Oil Pressure Transducer and Connector Change
80
98-001
98-001
2002-05
2003-02
2007-02
2010-05
2002-03
2005-02
STARTING
Smart Start
99
Beechcraft “How To” Videos Now Available on YouTube
100
ATA
ATA 97 Wiring Reporting
97-002
2014-03
2000-04