1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
© 2009 Edge Lighting. All Rights Reserved.
VEGA-H1-_
904-VEGA-H1-02
Installation Instructions for Vega Round and Oval (Halogen Version)
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
- Do not look directly at the lamp while the fixture is on.
- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Do not operate the luminaire with a missing or damaged
shield.
- Turn power off and allow to cool before replacing lamp.
IMPORTANT INFORMATION
- This product is ETL listed for indoor locations.
- This product can ONLY be ceiling mounted.
- This product can mount to either a 4" square electrical box
with round plaster ring or an octagon electrical box.
- This product can be dimmed with a low voltage electronic
dimmer.
SAVE THESE INSTRUCTIONS!
Adjust the Fixture Height
A
MOUNTING
PLATE
1: Determine the desired fixture height (H), from the bottom of
the glass shade to the top the mounting plate.
B
2
MOUNTING PLATE
H
STRAIN
RELIEF
AIRCRAFT
CABLE
STRAIN
RELIEF
GLASS SHADE
2
2
3
STRAIN RELIEF
BUSHING
4
2: Loosen the Phillips screw on each of the strain reliefs (Do
Not Remove).
CLEAR CORD
CORD GRIP
1.5MM ALLEN
WRENCH
AIRCRAFT
CABLE
3: Loosen the set screws on the strain relief bushings with the
the provided 1.5mm Allen wrench.
4: Loosen the cord grip to adjust the clear cord.
1
C
5: While holding the aircraft cables slide the mounting plate,
cover and the socket assembly down until the desired height
is achieved.
7
6: Tighten the set screw on each strain relief bushing with the
1.5mm Allen wrench.
AIRCRAFT
CABLE
MOUNTING PLATE
5
5
NUT
7
STRAIN RELIEF
BUSHING
6
7: Slide the strain relief down the aircraft cable against the
mounting plate and tighten the Phillips screw. Repeat this
step for the remaining strain reliefs.
D
1.5MM ALLEN
WRENCH
8
8
AIRCRAFT
CABLE
CLEAR CORD
COVER PLATE
3"
9
MOUNTING PLATE
8: Cut the excess aircraft cables off with a sharp cutter (Leave
at least 3" of the cable behind the strain reliefs).
9
CORD GRIP
9: Pull the excess clear cord out of the mounting plate and
tighten the cord grip.
E
10: From the end of the clear cord, strip the outer insulation
using a sharp knife. Make sure not to nick the inner
wires and trim off the cutout insulation.
F
10
11
6"
11: Replace the wires with the black and white tags near the
insulation. Leave 6" of the wire behind the mounting plate
for power connection. Trim off the excess wires.
2
Install the Fixture
G
ELECTRICAL
BOX HOLE
POWER WIRE
#8-32
SCREW
MOUNTING
PLATE
NOTE: Use the provided universal crossbar if the mounting
plate holes do not line up with the electrical box holes.
1: Feed the power wires through the mounting plate center
hole.
1
2
NOTE: Make sure the glass shade is detached.
2
2: Secure the mounting plate to the electrical box holes with
the two #8-32 screws provided.
H
3
5
4
3: Make sure the mounting plate and the bare wire is grounded
in accordance with local electrical codes.
4: Connect the clear wire with a white tag to the neutral power
wire with a wire nut.
5: Connect the clear wire with a black tag to the hot power wire
with a wire nut.
D
I
6: Slide the cover plate up against the mounting plate, the
magnets will hold the cover plate in place.
MAGNET
6
6
COVER
PLATE
6
3
Install the Lamps and Shade
J
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
Use MAX 150 Watt Type T10 Medium Base
Halogen Lamp For Each Socket.
1: Screw each lamp completely into the socket holes.
K
1
SOCKET
LAMP
GLASS SHADE
GLASS RING
HOLDER
2
2: Insert the glass ring holder on an angle into the glass shade
center hole and lay the glass shade on the glass ring holder.
L
3: To secure the glass shade in place, use the hooks inside the
glass shade and hook them inside of the glass ring holder.
4: Lower the socket assembly into the glass shade.
4
GLASS RING
HOLDER
GLASS SHADE
3
3
M
STRAIN
RELIEF
BUSHING
HOOK
1.5MM ALLEN
WRENCH
CORD GRIP
5: If the glass shade is not leveled horizontally, slide the cover
plate down to expose the mounting plate.
6: Readjust the uneven aircraft cable by loosening the set
screw on the strain relief bushing with the 1.5mm Allen
wrench. Push the aircraft cable in and re-tighten the set
screw.
7: Slide the cover plate up against the mounting plate.
COVER PLATE
AIRCRAFT
CABLE
CLEAR CORD
4