Congratulations on your new IKEA Kitchen,
and on the money you saved!
© Inter IKEA Systems B.V. 2012
INSTALLATION GUIDE FOR YOUR
AKURUM KITCHEN
Seven steps to a brand
new kitchen
It’s time to discover another major advantage
of investing in an IKEA kitchen – it’s a lot
easier than you might think to assemble and
install it yourself.
We encourage you to read both the guide
and posters in their entirety before getting
started. When you’re ready to begin a
particular step, be sure to hang the
corresponding poster on nearby wall.
We’ve already done most of the hard work
for you so that installation will be as simple
as possible. Plus, intelligent design makes it
easy to adjust cabinets, doors and drawers
for a perfect end result.
Have fun!
You’re only seven steps away from a brand
new kitchen. As you’ll quickly realize, it’s one
of the most rewarding projects you’ll ever do
– with results you’re sure to enjoy for years
to come!
Before you begin
This guide and corresponding posters will
take you through the preparation and
installation process step-by-step.
The posters provide a hands-free way to
refer to detailed installation instructions
while you work. We have also created a
Kitchen Installation video, available on www.
IKEA.ca, to give you an overview of the
installation process.
© Inter IKEA Systems B.V. 2012
2
The tools you’ll need
Pencil
Awl
Phillips screwdriver
Slotted screwdriver
Carpenter's rule or measuring tape
Hammer
Fine-toothed handsaw – for sawing
worktops, plinths etc.
Right angle square
Clamps
Jig-saw – for sawing holes for
the sink and the extractor fan
Level (4 foot)
Rasp/File
Electric drill
• drill holes for handles,
wall fittings etc.
• assemble and install cabinets
Adjustable wrench – to fasten wall
cabinets to the suspension rail, and
for cutting holes with the FIXA tool
© Inter IKEA Systems B.V. 2012
FIXA 35 mm hole cutter –
to drill extra holes for the tap
in the sink (if necessary)
3
Mitre box with saw –
to ensure that you cut
the cornices at exactly
the right angle
Step 1. Prepare
your kitchen
Marking cabinet position
Measure and draw in the position of your
cabinets on the wall so you can be sure
everything fits.
A little preparation can save a lot of time
later on – especially when it comes to
installing your kitchen.
Removing the old kitchen
Before removing old cabinets and
countertops, switch off the electricity, gas
and water. Remove base cabinets first, so
that you can easily get to the wall cabinets.
Mapping out utilities
If you’re re-routing water or gas pipes or
making changes to electrical outlets, hire
qualified specialists. They will do a safe and
professional job.
Checking for uneven spots
Flat, level surfaces are the best start for a
good installation. Take the time now to locate
and correct uneven walls and floors. The first
three points on the step 3 poster show how
to check. If major problems need to be fixed,
you may want to hire a professional.
© Inter IKEA Systems B.V. 2012
Preparing the walls and floor
With the room empty, now is the time to
prime walls, put on a first coat of paint,
and/or install new flooring. Keep in mind,
new flooring is easier to install now, but be
sure to protect the surface until the kitchen
is finished. The second coat of paint and any
wallpapering should be completed after the
cabinets are installed.
4
Step 2. Get organized
Assembling wall cabinets
Follow the instructions included in each
package to assemble the wall cabinets, since
you’ll most likely be installing these first.
Don’t put on doors, shelves, knobs or handles
just yet.
Being well-organized makes any job easier.
After your kitchen is delivered, double check
the packages you received against the packing
list to make sure everything is there. Then,
sort the packages into cabinet groups
according to their labels, preferably in a
room other than the kitchen.
Using the right fixing hardware
Plaster, brick or drywall? Because there are
many different types of wall, fixing hardware
is not supplied with your cabinets. Most hardware
stores stock appropriate fixing screws and
heavy duty anchors for each type of wall.
Assembling base and high cabinets
Next, assemble base cabinets, drawers and
high cabinets, following the enclosed
instructions. Hint: it’s easier to screw the
runners for drawers or pull-out baskets on
the inside walls of the base and high cabinets
before assembling the cabinets themselves.
Finding a safe spot for the countertop:
If you purchased a solid wood countertop from
IKEA, be sure to store it in or near the kitchen.
This allows it to adjust to room temperature.
Place the cabinets in order
Arrange the cabinets into the order in which
you will be installing them so that you can
quickly find the right cabinet when you need it.
© Inter IKEA Systems B.V. 2012
5
Step 3. Hang the
wall cabinets
Note: If your kitchen layout doesn’t include
wall cabinets, please skip to Step 4.
In some cases, depending on the layout,
appliances and countertops, it may be better
to begin with the base cabinets. To start with
wall cabinets, hang the step 3 poster on the
wall. It will take you through each step for
installing the wall cabinets, including:
This is where the fun really begins. In most
kitchens, it is best to begin the installation
with the wall cabinets. This way there won’t
be any base cabinets to work around and
you can more easily use a step-ladder.
•
•
•
•
•
ts
bine
l ca
wal
the
ang
3. H
Step
Finding wall studs
Position the suspension rail
Mounting the wall cabinets
Levelling the wall cabinets
Securing the wall cabinets
ns
ctio
instru
’ll
these ll so you e!
Hang
wa
ds fre
on the r han
e you
hav
dy
stur
ga
usin
nted
ng
mou
l
are
a stro
leve
res
nets
and
ensu
cabi
hang
This
wall
er to
RUM
easi
on rail.
AKU
ensi
es it
l susp and mak
sure
stee
ion,
1, mea
to
wall
Step
installat nets.
so in
on the
cabi
ve
done
the
you’
nets
ady
cabi
be sure
of the
n’t alre
.
Also
tion
have
wall
fit.
posi
the
will
If you
the
s on
ything
draw
spot
ever
and
high
and
re that
ensu
uneven
ked
mar
Step
pleted
ve com
n you’
Whe
of the
3, all
wall
nets
cabi
will
d
all
the
dryw
tap
s in
line,
stud
rail
the
a studnsion
ing
its
use
ed susper out (or
Mark
5. Find
lly
mark
stud.
usua
corne
first
At the
are
the
wall
for the
from
t studs
the
or 24”
wall
for
check
12”
quen
on
r) to
lines
be at
subse
locati
you
finde
n rail
may
level
the
While
the
they
ensio floor that
ion.
83
ns. Mark will show
vals,
posit
wall
4. Mark and susp on the
inter
to
kitche
This
rail
ets
92
up the
line.
point
some
at 16”
ure
nsion
the
cabin
ets or
high
als in
the
suspe
along
cabin
1, meas
e the
interv
wall
stud
Using
h the
Step
, locat
ed in
of 30”
uring
Next
of each e to attac
top
mark
ets.
wher
by meas
for the wall cabin
rail
you
ets)
7/8”
nsion
cabin
wall.
for 39”
the
lines
suspe
ontal
5/8”
the
level
horiz
of
m
draw
(3” for
botto
2 1/2” mark. Then
down
first
the
from
wall.
the
on
when
et
d
cabin
threa
re the the bolt,
et,
secu
over
cabin
l and
the
l plate
sary.
Leve
meta
. Level if neces
10.
et
small
in place m edge
cabin
Fit the loosely
e the
botto
you
nut
one
et
at the
ly secur will allow
the
shims
et, align with
er cabin
ch, loose n; this
using
the
corn
wren
r cabin
are
tighte
the
your
all of
corne
hardw cabinet.
With
Do not ts once
rail
9. Hang with the
are.
of the
nsion
tmen
ing
are.
hardw
top
suspe
adjus
Start
lled.
at the
its hardw et,
of the
to make are insta
hole
and
piece
illed
ets
d hole corner cabin the
predr
cabin
a
secon
the
both
ion the don’t have against
space
Posit
filler
a high
If you et that fits ing the
lling
ning
Note:
allow
be insta and tighte
ll a cabin walls,
will
ts
be
you
ld
insta
side
tmen
If
:
shou
and
adjus
plan.
lled
are
Note
back
insta
your
hardw
et, final
et is
n on
ting
cabin
show
cabin
moun
high
is level.
of the
the
thing
after
every
done
re that
to ensu
When
s B.V.
2012
ws
scre
ted,
moun
nting
ts
mou
been
tmen
the
ten
ets have final adjus ting
Tigh
cabin
and
moun
all wall
cted,
of the
place
conne
n all
s in
d and
, tighte ic cover
aligne
made
plast
et.
been
the
have
Slide
r brack
are.
l corne
hardw
meta
the
over
14.
ther
with
sed
toge
ets
s enclo
en cabin n screw holes and
Fast
ectio
the
nue
conn
the
es into
ps. Contitogether
Place
et fram the clam
ets
cabin
ve
cabin
the
n. Remo remaining
tighte
the
ning
way.
faste
same
in the
13.
et walls inside of
cabin
drill
on the
ugh
thro
holes
a 3/16"
the
use
illed
Drill
from
12.
predr
all doors h holes
find
ets
d and
You’ll
et. For the fourt
secon
cabin
cabin
gh
wall
each
s.)
throu
same
s. (The
the
drill
ining
m edge door hinge
ets in
rema
bit to
one.
botto
the
ous
cabin
for the
and
ent
previ
Hang
are
top
of the
adjac
the
11.
rest
holes
with
y hold
the
third
ing the
Hang
ing each temporaril
marr
align
s to
To avoid small scrap
way,
clamp
a
ion.
your
use
posit
Use
the
ets,
ets into
cabin
p and
cabin
your
clam
the
ce of
een
surfa
betw
of wood
et.
cabin
System
,
n rail
studs
ensio
the
to the
susp
with
rail
rail
a
re the
nsion
of the
found
8. Secu the suspe
1,
If you
m edge
re
wall.
botto
in Step
Secu
the
1/4”
ware
ht.
ing the
ed on
the
hard
than
align
is straig
mark
into
n rail
line
are
of more until it
een
ensio
level
wall
You’ll
hardw
rail
up.
in the
rt susp nsion rail
nsion
fall betw heav y
g it
sure
bow
rail
a
suspe
7. Inse suspe
e puttin et. (Be
the
with
of the
the
befor
wall
end
shim
cabin
of the
rail
Slide
wall
ld the
to the
side
nsion
e it
s per
Shou
suspe
ets to
on each
piece
for one.) are
, secur
n rail
two
cabin
calls
piece
studs
or.
ensio
hardw
wall
need
anch
the
susp
the
ion one if your plan
de the if
the
duty
tape
h of
posit
Inclu
et
to
to
Cut
only
lengt
ul
wall.
6.
et
up.
the
r cabin it helpf
one
cabin
ure
1/4”
goes
corne
find
act
along
high
rail
Meas
da
lled
may
the
. Subtr
will
You
until
be insta wall behin 12” deep
(This
place
rail.)
h of
ent.
into
et is
the
lengt
of
urem
cabin
high
ll meas either end nsion rail
the
overa
at
suspe
the
from
of space to cut the
1/8”
saw
leave
hack
your
h.
Use
lengt
to this
IKEA
© Inter IKEA Systems B.V. 2012
. The
point
all
its high Check
to find as well.
or
2. Next
floor
base
here
k the
lling
low
you
Chec
and
insta
help
l be
high
will
level
e you’l mark the
wher
and
areas
ets,
cabin
wall.
high
the
s on
point
angle
right
if
see
re or
lly
r, and the
n squa
3. Fina
corne
inatio
it and
each
comb
een
call
Fit a
l into
betw
1/4”,
pane
gaps
a “U”
than
wood
any
. In
are
site
is more
tance
gap
there
oppo
assis
een
If the
rt for
betw
if they
wall.
expe
ure
see
IKEA
n, meas spots to
your
d kitche
er of
shape
numb
at a
walls
lel.
paral
are
© Inter
Hang the
poster on
the wall
for Step 3
s
en spot lly and
unev
visua
ce.
for
walls
surfa
king
the
the
and
1. Chec checking
along
as bows be
by
level
to
such
Start
4 foot
ies,
need
ng a
al.
ularit
ems
ssion
runni
irreg
r probl a profe
any
s
Mark
. If majo to hire
shim
spots
want
to use
high
may
ssary
you
be nece cabinets.
fixed,
also
the
ting
It may
moun
Making the job easier on yourself
Keep in mind, hanging wall cabinets is easiest
to do with a partner and a sturdy step ladder.
Always start with a corner cabinet and work
your way out. Once you’ve completed all the
steps on the poster, you’re ready to install
base and high cabinets.
e.
plac
be in
6
Step 3. Hang the wall cabinets
Hang these instructions
on the wall so you’ll
have your hands free!
AKURUM wall cabinets are mounted using a
sturdy steel suspension rail. This ensures a strong
installation, and makes it easier to hang and level
the cabinets.
If you haven’t already done so in Step 1, measure
and draw the position of the cabinets on the wall to
ensure that everything will fit. Also be sure you’ve
marked uneven and high spots on the wall.
When you’ve completed Step 3, all of the wall cabinets will be in place.
1. Checking for uneven spots
2. Next
3. Finally
4. Mark the level lines for the wall
5. Finding the studs in drywall
Start by checking the walls visually and
Check the floor to find its high point. The
Fit a combination square or right angled
cabinets and suspension rail
At the marked suspension rail line, tap the
running a 4 foot level along the surface.
level will help you here as well. Check all
wood panel into each corner, and see if
Using the high point on the floor that you
wall from the corner out (or use a stud-
Mark any irregularities, such as bows and
areas where you’ll be installing base or
there are any gaps between it and the
marked in Step 2, measure up the wall 83
finder) to check for the first stud. Mark its
high spots. If major problems need to be
high cabinets, and mark the high and low
wall. If the gap is more than 1/4", call
7/8" for the top of 30" wall cabinets or 92
position. While subsequent studs are usually
fixed, you may want to hire a professional.
points on the wall.
your IKEA expert for assistance. In a "U"
5/8" for 39" wall cabinets. Next, locate the
at 16" intervals, they may be at 12" or 24"
It may also be necessary to use shims
shaped kitchen, measure between opposite
bottom of the suspension rail by measuring
intervals in some kitchens. Mark the location
when mounting the cabinets.
walls at a number of spots to see if they
down 2 1/2" (3" for horizontal cabinets)
of each stud along the line. This will show
are parallel.
from the first mark. Then draw level lines
you where to attach the suspension rail to
on the wall.
the wall.
6. Cut the suspension rail
7. Insert suspension rail hardware
8. Secure the suspension rail
9. Hang the corner cabinet
10. Level and secure the cabinet
Measure the length of the wall cabinets to
Slide the suspension rail hardware into the
Secure the suspension rail to the studs,
Starting with the corner cabinet, align one
Fit the small metal plate over the bolt, thread
be installed along one wall. Include the
suspension rail before putting it up. You’ll
aligning the bottom edge of the rail with the
piece of the suspension rail hardware with
the nut loosely in place. Level the cabinet,
length of wall behind a high cabinet only if
need two pieces per wall cabinet (be sure
level line marked on the wall. If you found a
the predrilled hole at the top of the cabinet.
using shims at the bottom edge if necessary.
the high cabinet is 12" deep. Subtract 1/4"
to position one piece on each side of the
bow in the wall of more than 1/4" in Step 1,
Position the second hole and its hardware.
With your wrench, loosely secure the cabinet
from the overall measurement (this will
corner cabinet if your plan calls for one).
shim the suspension rail until it is straight.
Note: If you don’t have a corner cabinet,
hardware. Do not tighten; this will allow you
leave 1/8" of space at either end of the
You may find it helpful to tape the hardware
Should the end of the rail fall between
install a cabinet that fits against both the
to make adjustments once all of the
rail). Use your hack saw to cut the
into place until the rail goes up.
studs, secure it to the wall with a heavy
back and side walls, allowing the filler space
cabinets are installed.
duty anchor.
shown on your plan.
suspension rail to this length.
Note: If you will be installing a high
cabinet, final adjustments and tightening
of the mounting hardware should be
done after the high cabinet is installed
to ensure that everything is level.
12. Drill through cabinet walls
13. Fasten cabinets together
14. Tighten the mounting screws
Hang the rest of the cabinets in the same
You’ll find predrilled holes on the inside of
Place the connection screws enclosed with
When all wall cabinets have been mounted,
way, aligning each with the previous one.
each cabinet. For all doors use a 3/16" drill
the cabinet frames into the holes and tighten.
aligned and connected, and final adjustments
Use your clamps to temporarily hold
bit to drill through the fourth holes from the
Remove the clamps. Continue fastening the
have been made, tighten all of the mounting
adjacent cabinets into position. To avoid
top and bottom edges (the second and third
remaining cabinets together in the same way.
hardware. Slide the plastic covers in place
marring the surface of your cabinets, use a
holes are for the door hinges).
small scrap of wood between the clamp
and the cabinet.
over the metal corner bracket.
© Inter IKEA Systems B.V. 2012
11. Hang the remaining wall cabinets
Step 4. Install base
and high cabinets
Getting started
As with the wall cabinets, you’ll start by
installing the corner cabinet first. If your
plan doesn’t include a corner cabinet, start
with the cabinet that fits at the start of the
run against both the back and side walls.
The Step 4 poster will guide you through the
process of installing base cabinets and high
cabinets. These cabinets are designed with
sturdy, adjustable legs for easy levelling on
uneven floors. This step includes:
•
•
•
•
•
•
•
Attaching cabinet legs
Installing base cabinets
Installing a high cabinet
Levelling cabinets
Securing cabinets together
Installing filler pieces
Installing a corner lazy-susan
Hang
the
on the se ins
tructio
wa
hav
e you ll so you ns
r han
’ll
ds fre
e!
Step
4. In
stal
l the
base
and
high
cabi
nets
Nex
t, it’s
time
Befo
for the
re you
and
base
begin,
othe
and
note
r utili
care
all plum high cabi
ties.
fully
nets
bing
opening , and, usin Measure
.
, pow
thes
ga
er sour
s befo
e loca
re each hole saw
ces
tions
, cut
cabi
In the
the
net
follo
appropr
is inst
wing
fron
alled
iate
t of
step
.
the
s, you’
board
cabi
ll inst
nets
to the
, and
all the
pack
wall
secu
ed toge
. This
legs
re
at the
pref
er, you ther with is a leng a cabinet
th of
supp
the
in lieu
can
toeort
part
use
of the
kick
icleb
legs
panels.
oard
supp
on the
ort boa
If you
back
rd.
of the
cabi
nets
Whe
IMPORTANT!
Before putting in any of these cabinets, be
sure to measure, mark and cut openings for
plumbing, power sources and other utilities.
n you’
ve com
plete
1. Mark
ing
Using
the
level
the
high
mark
lines
ed earlie point
of the
4 foot
r, meas
floor
level
that
heigh
to draw ure up
t. Now
4 5/16” you
a line
meas
. Use
on
point
ure
a
34 1/2” the wall
level
on the
at this
line.
floor
from
This
the
and
the
will
base
draw
help
cabin
anoth
you
ets.
level
er
the
top
of
same
d Step
4, all
of the
3. Secu
re the
Align
supp
the
ort
top
with
edge
boar
the
d
of the
level
Secu
line
supp
re it
you
ort board
to the
the
mark
suppo
studs
ed at
rt board
. Shou
4 5/16”
it to
the
fall betw ld the
.
wall
end
with
of
a heav een studs
, secur
y-dut
y anch
e
or.
5. Drill,
anch
Using
or
and
the
appro
scre
screw
w
for your priate
drill
the
wall
spots
bit and
mate
you’v
inser
type
rial,
t a heav e mark
of
drill
ed.
y-dut
If there holes at
tighte
n halfw y anchor
’s no
stud,
then
ay.
the
screw
and
cabi
net
fram
es will
be in
plac
e.
2. Cut
base
Meas
cabin
ure
et supp
the
cabin
ort
ets to length of
boar
wall
the
be insta
ds
base
space
lled.
and
behin
cabin
high
d appli Do not
et supp
includ
lengt
ance
e the
hs. Cut ort board
s. Cut
a side
into
the
the
base
meas
board
toeki
ured
ck is
1 1/2”
plann
short
ed.
er wher
e
6. Insta
ll the
Lift
corn
the
corne
er cabin
adjus
r cabin
t the
et back et
legs
so that
into
it stand
place
s level. and
7. Secu
re the
Tight
cabin
en the
et to
Assu
screw
the
re that
s, but
wall
the
not
cabin
and
comp
sideet is
letely
to-sid
level
.
SUSA
e. Hint:
front
N is
-toeasie
terto
Insta
ps are
r now
lling
the
than
in place
after
.
the
4. Star
t with
Attac
the
h legs
corn
cabin
to
er cabin
ets accor the front
et
If you
edge
ding
are
to packa s of the
not
attac
using
h back
ge instru
the
leg at
legs
supp
as well.
the
ort boardctions.
end
attac
Alwa
of the
hing
ys use ,
run,
the
side
a back
as this
toe-k
ick easie makes
r.
Note
: Legs
see
can
the
be share
instru
cabin
d by
et again ctions.
two
edge
cabin
st the Place the
is
ets,
corne
wall
Throu resting
so that
r
on the
gh the
its
of the
supp
holes
ort boardback
cabin
at
fixing
et, mark the top
.
screw
back
wher
there
. Set
corne
e to
´s no
the
rs
drill
cabin
corne
cabin
et aside for the
et that
r cabin
side
. If
et,
will
walls
fit again install
the
on your , allow
ing the st the
plan.
back
filler
space and
show
n
back
LAZY
coun
10.
Fast
en cabin
Place
the
ets
conn
toge
the
ectio
cabin
n screw ther
et fram
tighte
s enclo
es into
n. Conti
rema
sed
the
nue
with
ining
holes
in this
base
and
fashi
cabin
on with
ets.
the
11.
Insta
ll the
The
high
high
cabin
cabin
same
et shou
et
way
you
ld be
If you´r
insta
insta
e using
lled
lled
moun
the
a cover the base
t this
cabin
using
befor
pane
ets.
e insta
l on
the
enclo
one
ll-ing
side,
sed
the
instru
cabin
ction
et
s.
8. Insta
ll the
Mark
next
, drill,
base
next
and
cabin
inser
cabin
t the
et
et. Lift
caref
screw
ully
the
aligni
s for
cabin
and
ng it
the
secur
et into
ing them with the
place
previ
,
toget
ous
her
cabin
with
a clam et
p.
9. Drill
thro
a 3/16" ugh the
cabin
drill
bit to
et walls
from
drill
the
throu
top
lling
gh the
a draw and botto
fourth
er cabin
m edge
from
s. When
et, drill
the
top.
throu
gh the
Use
holes
insta
fifth
hole
12.
Tigh
ten
When
all the
all base
scre
and
ws
cabin
align
ets have
ed,
Now
tighte
the
been
n all
high
final
moun
screw
cabin
13.
adjus
ted
s into
Meas
et is
tmen
in place
the
ure
Chec
ts to
n all
filler
k the
, make wall.
the
the
piece
wall
wall
screw
even
the
cabin
s
with
and
s.
ets and
your
flat.
from
level
If so,
the
to see
meas
wall
dista
to
ure
14.
if it
nce
the
is
Cut
at the the cabin
piece
filler
et and distance
a line
top
. Note:
peice
and
conn
mark
pictu
sWith
rial
ectin
on the
this
re 16. If the wall bottom
so that
a hand
g the
the
front
cabin
is unev of the filler
filler
top
it’s the
saw:
the
side
et.
and
face
will
en,
ass
draw
of the
botto
be insta Hold it
skip
a coup
side
the
m mark
in place
filler,
to
up.
filler.
le of
lled.
again
Jigsa
and
s
inche
Open
Put
st the
horiz
w: mark
the
cut
mask
s and
front
it with
the
ontal
16.
wall.
ing
both
If the
place
side
and
wall
Holdi
from
sides
to preve tape over
level,
the
so that
wall
If the
ng the
the
of
follow
back
is unev
the
the
wall
nt chipp
the
comp
line
temp
side.
is not
the
penc
must
ass
en
on
ing.
line
late.
il trace
level
be cut
corre
Cut
ct width To cut
s a clear of the
To do
it
to confo and flat,
the
this,
, meas the temp
the
line
rm to
farth
for tracin you’l
filler
late
on
ure
est
the
l need
cabin
to the
point
the
g the
piece
et. Find
dista
to make wall’s shap
on the
wall’s
nce
of thin
temp
e.
the
wall
a
from
shap
late
make
same
plywo
to the
e onto template
and
sa
from
point
mark
the
a meas suitable od or heav
this
filler.
it. Draw on the
point
temp
temp
y cardb
uring
A
to
late
late.
a straig
tape,
oard
to form the top
You’ll
17.
again
penc
ht
Prep
and
line
also
st the
il and
the
botto
need
flat
To produ are the
check
cabin
comp
m of
et. Cut edge that
area
that
ass.
the
ce an
wall
it fits,
the
to be
will
the
airtig
fller
and
fit
temp
then
caulk
ht seal
the
and
aroun
late
pictu
trace
cabin
ed
follow
and
betw
re 14.
d the
the
et, you’l
the
een
shap
latex
filler
cuttin
the
18.
l need
piece
brand
g direc e onto
The
to caulk
s. Choo
wate
(it does
finis
tions
Dab
rproo
hing
in
your
f.) Tape n’t need se a well
caulk
touc
finge
the
made
h
ed.
to be
r into
along
caulk
Apply
crevi
a 3-in-1
from
finge
a bead side the
ce.
sticki
r along
oil to
of caulk area to
ng,
crevi
preve
then
be
ce. Remothe caulk
into
nt
the
, forcin run your
seal
ve
and
g it
a straig the tape
into
the
ht edge for an
airtig
.
ht
tighte
15.
Insta
ll filler
Put
the
piece
filler
edge
s
piece
again
in place
st the
with
wall.
throu
the
inside
Attac
gh the
cut
h by
of the
predr
drillin
piece
illed
cabin
ga
s in
holes
et. Insta
the
finish
ll other from the
ed insta same way.
pictu
filler
lling
When
re 17.
all filler
you’v
e
piece
s, go
to
screw
Cut
the
temp
same
late
heigh
mate
t as
the
e
wher
comp
point
© Inter
IKEA
s B.V.
System
2012
© Inter IKEA Systems B.V. 2012
7
Hang the
poster on
the wall
for Step 4
Step 4. Install the base and high cabinets
Hang these instructions
on the wall so you’ll
have your hands free!
Next, it’s time for the base and high cabinets.
Before you begin, note all plumbing, power sources
and other utilities. Measure these locations
carefully, and using a hole saw, cut the appropriate
openings before each cabinet is installed.
In the following steps, you’ll install the legs at the
front of the cabinets, and secure a cabinet support
board to the wall. This is a length of particleboard
packed together with the toe-kick panels. If you
prefer, you can use legs on the back of the cabinets
in lieu of the support board.
When you’ve completed Step 4, all of the cabinet frames will be in place.
Note: Legs can be shared by two cabinets,
see the instructions. Place the corner
cabinet against the wall so that its back
edge is resting on the support board.
1. Marking the level lines
2. Cut base cabinet support boards
3. Secure the support board
4. Start with the corner cabinet
Through the holes at the top back corners
Using the high point of the floor that you
Measure the length of the base and high
Align the top edge of the support board
Attach legs to the front edges of the
of the cabinet, mark where to drill for the
marked earlier, measure up 4 5/16". Use a
cabinets to be installed. Do not include the
with the level line you marked at 4 5/16".
cabinets according to package instructions.
fixing screw. Set the cabinet aside. If
4 foot level to draw a line on the wall at this
wall space behind appliances. Cut the base
Secure it to the studs. Should the end of
If you are not using the support board,
there´s no corner cabinet, install the
height. Now measure 34 1/2" from the
cabinet support board into measured
the support board fall between studs, secure
attach back legs as well. Always use a back
cabinet that will fit against the back and
same point on the floor and draw another
lengths. Cut the board 1 1/2" shorter where
it to the wall with a heavy-duty anchor.
leg at the end of the run, as this makes
side walls, allowing the filler space shown
level line. This will help you level the top of
a side toekick is planned.
attaching the side toe-kick easier.
on your plan.
the base cabinets.
5. Drill, anchor and screw
6. Install the corner cabinet
7. Secure the cabinet to the wall
8. Install the next base cabinet
9. Drill through the cabinet walls
Using the appropriate drill bit and type of
Lift the corner cabinet back into place and
Tighten the screws, but not completely.
Mark, drill, and insert the screws for the
Use a 3/16" drill bit to drill through the fourth
screw for your wall material, drill holes at
adjust the legs so that it stands level.
Assure that the cabinet is level front-to-
next cabinet. Lift the cabinet into place,
holes from the top and bottom edges. When
the spots you’ve marked. If there’s no stud,
back and side-to-side. Hint: Installing the
carefully aligning it with the previous cabinet
installing a drawer cabinet, drill through the
insert a heavy-duty anchor then the screw
corner base cabinet carousel is easier now
and securing them together with a clamp.
fifth hole from the top.
and tighten halfway.
than after the countertops are in place.
10. Fasten cabinets together
11. Install the high cabinet
12. Tighten all the screws
13. Measure filler pieces
14. Cut filler pieces
Place the connection screws enclosed with
The high cabinet should be installed the
When all base cabinets have been mounted
Check the wall with your level to see if it is
With a handsaw: draw a line connecting the
the cabinet frames into the holes and
same way you installed the base cabinets.
and aligned, tighten all screws into the wall.
even and flat. If so, measure the distance
top and bottom marks on the front side of
tighten. Continue in this fashion with the
If you´re using a cover panel on one side,
Now the high cabinet is in place, make the
from the wall to the cabinet and mark this
the filler, and cut it with the face side up.
remaining base cabinets.
mount this before installing the cabinet
final adjustments to the wall cabinets and
distance at the top and bottom of the filler
Jigsaw: mark both sides of the filler. Put
using the enclosed instructions.
tighten all the screws.
piece. Note: if the wall is uneven, skip to
masking tape over the line on the front side
picture 16.
to prevent chipping. Cut it from the back side.
Cut the template material so that it’s the
same height as the cabinet. Hold it in place
where the filler will be installed. Open the
compass a couple of inches and place the
point against the wall. Holding the compass
horizontal and level, follow the line of the
wall so that the pencil traces a clear line on
the template. To cut the template to the
correct width, measure the distance from
16. If the wall is uneven
the farthest point on the wall to the cabinet.
17. Prepare the area to be caulked
18. The finishing touch
Put the filler piece in place with the cut
If the wall is not level and flat, the filler
Find the same point on the template and
To produce an airtight seal between the wall
Dab your finger into a 3-in-1 oil to prevent
the caulk from sticking, then run your
edge against the wall. Attach by drilling a
must be cut to conform to the wall’s shape.
mark it. Draw a straight line from this point
and the cabinet, you’ll need to caulk around
screw through the predrilled holes from the
To do this, you’ll need to make a template
to the top and bottom of the template to
the filler pieces. Choose a well made latex
finger along the caulk, forcing it into the
crevice. Remove the tape for an airtight
seal and a straight edge.
inside of the cabinet. Install other filler
for tracing the wall’s shape onto the filler.
form the flat edge that will fit against the
brand (it doesn’t need to be waterproof.)
pieces in the same way. When you’ve
A piece of thin plywood or heavy cardboard
cabinet. Cut the template and check that it
Tape alongside the area to be caulked.
Apply a bead of caulk into the crevice.
finished installing all filler pieces, go to
makes a suitable template. You’ll also need
fits, then trace the shape onto the filler and
picture 17.
a measuring tape, pencil and compass.
follow the cutting directions in picture 14.
© Inter IKEA Systems B.V. 2012
15. Install filler pieces
Step 5. Install the
countertop
Solid wood countertops
The Step 5 poster details the installation,
care and maintenance of these durable solid
wood countertops.
The base for your new kitchen is now in
place. Now it’s time to turn your attention to
the countertops and sink.
In addition to the solid wood countertops
detailed in this step, IKEA also offers a wide
range in custom countertops.
•
•
•
•
•
•
•
•
op
tert
coun
l the
stal
5. In
Step
ns
ctio
instru
’ll
these ll so you e!
Hang
wa
ds fre
on the r han
e you
hav
This
sink.
of
nce
p and
tena
terto
main
coun
and
ll the
care
to insta llation
it’s time the insta ps.
Now
ils
terto
d tops
er deta d coun
woo
on
post
woo
the solid ing them
solid
hed
our
sawing est plac
ve finis ect
g and
you’
sugg
surin
Once
, we
to conn ,
step
n mea
ling.
nals
this
Whe
hand
essio
the oven
ughout
easiest to hire prof install
thro
for
to
es
idea
y, and
sawhors it’s a good
tricit
5,
or elec
Step
r, gas lighting.
the wateher and
dishwas
Bringing in the professionals
Your new kitchen is beginning to take shape!
At this point, you’ll probably need to hire a
professional to connect water, gas or
electricity and to install the dishwasher, oven
and lighting.
e.
d Step
5, the
ps and
sink
will
plac
be in
terto
coun
plete
ve com
n you’
Whe
g the
along
tratin
cuto
pene
sink
from
the
ne seal
ture
retha
6. Seal nt mois
.
a polyu
To preve p, apply a paintbrush
terto
s with
coun
the
cut
on
ctly
t will
of the
corre
d
cutou
e down
g it
sink
aroun
upsid
ionin
the
sink
the
p, posit back. Trace
place
terto
to
il.
coun
front
a penc
and
of the
with
sink
to side
side
of the
the
edge
rails
on the
et top
place
is
into
cabin
hole
the
p back the sink
of the
terto
7. Trim
e rails
k that
coun
the
fram
Fit the
et. Chec the top
to trim
cabin
by
l need rly.
base
you’l
ucted
it is,
obstr
fit prope
not
et. If
will
cabin
sink
the
base
so that
rails
e
it upsid s.
turn
sink
horse
p and
ll the
saw
terto
coun
8. Insta
on your
sink
off the g it back
to the
Lift
ding
, placin
accor
s.
down
sink
ction
ll the
instru
Insta
rer’s
factu
manu
p
ed as
terto
coun
be secur ded. The
re the should
provi
to
are
9. Secu tertop
terop
hardw
coun
coun
the
the
Your
Set
n using ets allow
ally.
same
show
norm
act
d brack
ing the e
contr
slotte
, allow
Locat
and
nd and in place
ured.
vals
expa
ps
meas
terto
ar inter top.
you
coun
regul
s at
as when
ing the
gaps
t point
e secur
hmen
befor
attac
holes
pilot
drill
edge
IKEA
System
s B.V.
ty
for
beau
arly
regul
-term
s
. Stain
re long counterop
ction
Assu
using
12.
oil your and prote
ved
and
ty
be remo surface
Sand
use
beau
ed
p for
term
ge can
sand
longterto IKEA was
the
r dama
area.
coun
mino
r. Wipe
ted
and
and
p from
wood
pape
affec
ition
terto
are
sand
l the
for
cond
coun
Prep
fine
re-oi
re it
ry to
wood
and
r
prepa
facto
solid
pape
clean
n. To
Your
at the
sand
llatio
ved
eated
a fine
insta
appro
pretr
until
ce with NDLA
ct it
surfa
BEHA
prote
the
IKEA
sand
use,
it with
finish
and
k oil.
-bloc
wood
2012
© Inter IKEA Systems B.V. 2012
ut
a
. Drill
orses
hole
four
sawh
sink
the
p on
at all
same
terto
5. Saw
w blade ing this
coun
jigsa
the
Place
for the line. Follow sink unit.
hole
cut
1/2”
the
for the
hole
rs of
the
corne
saw
line,
cut
mend
p
recom
terto
ol. To
, we
coun
contr
the
by hand saw for
over
3. Saw sawing
p, tape
d hand
lar
e
a circu
If you’r fine-toothe counterto
p
a
the
e using
clam
ering
using
If you’r down and
splint
cut.
saw
avoid
to be
ter face guide the
with
area
coun
to
the
edge
the
place
cut
turn
the
ge in
saw,
ht-ed
Finish
line.
a straig
cut
the
along
file.
your
, draw
ht edge to the
a straig
ding
accor
il and
penc
line,
sink.
this
your
your
Using line inside
with
came
a “cut”
that
tions
direc
© Inter
Hang the
poster on
the wall
for Step 5
of the
ter
end
coun
the
the
cover
ure
ter from for the
a
ing
with
2. Meas the coun
allow
Mark
ure
using
ang.
Meas
l be
et out,
overh
cabin
if you’l using a
p
base
a 1/2” ed side
if
terto
base
rside
l plus
finish
coun
of the wall, and
unde
pane
the
the
top
il on
on the
tion
back
p on
and
or high
penc
t the
1. Posi counterto
saw
wall
the
“L”
a hand
ing 1/8”a the side
Lay
st
in an
allow
r saw.
ets,
again
tops
powe
in a
cabin
lling
meet
er space e insta
-cut
must
a small If you’r
ons
or mitre
et.
secti
angle
ter to
cabin
two
n.
make
coun
e, the
not
the
actio
shap
(Do
contr
allow
joint.
e steps nsion and
butt
.) Thes al expa
joints
norm
rgo
unde
sink
the
the
, trace
for
rside
place
unde
a spot
p in
the
et on
e that
4. Mark counterto
,
cabin
assur
the
Then
base
helps
ctly.
With
of the
p. This
d corre
rside
inside
terto
unde
be aligne
the
coun
11.
t
fauce
et
for the
fauc
the
rilled
ll the
cut
mark
Insta is not pre-d need to
and
10.
l
sink
Tape
you´l
all
sink.
If your fittings,
in the
gs. Drill
and
fittin
or other
holes
tool
of the
ssary
FIXA
ing the
nece
the
for each
gs follow
aid of
a place
the
fittin
with
t and
s.
holes
fauce
ction
ll the
instru
insta
rer´s
factu
manu
Measuring countertop lengths
Making a corner seam
Sawing the countertop
Cutting a hole for the sink
Sealing cut edges
Installing the sink
Installing the countertop
Installing the tap
8
Step 5. Install the countertop
Hang these instructions
on the wall so you’ll
have your hands free!
Now it’s time to install the countertop and sink. This
poster details the installation care and maintenance
of our solid wood countertops.
When measuring and sawing the solid wood tops
throughout this step, we suggest placing them on
sawhorses for easiest handling. Once you’ve finished
Step 5, it’s a good idea to hire professionals to
connect the water, gas or electricity, and to install
the oven, dishwasher and lighting.
When you’ve completed Step 5, the countertops and sink will be in place.
1. Position the countertop
2. Measure the counter
3. Saw the countertop
4. Mark a spot for the sink
Lay the countertop on top of the base
Measure the counter from the end of the
If you’re sawing by hand, we recommend
With the countertop in place, trace the
cabinets, allowing 1/8" at the back wall, and
base cabinet out, allowing for the cover
using a fine-toothed handsaw for control. To
inside of the base cabinet on the underside
a smaller space against the side wall or high
panel plus a 1/2" overhang. Mark with a
avoid splintering the countertop, tape over
of the countertop. This helps assure that
cabinet. If you’re installing tops in an "L"
pencil on the finished side if you’ll be using
the area to be cut. If you’re using a circular
the sink cutout will be aligned correctly. Then,
shape, the two sections must meet in a
a handsaw and on the underside if using a
saw, turn the counter face down and clamp
place the sink upside down on the underside
butt joint (do not make angle or mitre-cut
power saw.
a straight-edge in place to guide the saw
of the countertop, positioning it correctly
Using your pencil and a straight edge, draw
joints). These steps allow the counter to
along the cut line. Finish the cut edge with
side to side and front to back. Trace around
a "cut" line inside this line, according to the
undergo normal expansion and contraction.
your file.
the edge of the sink with a pencil.
directions that came with your sink.
5. Saw the sink hole
6. Seal the sink cutout
7. Trim the cabinet top rails
8. Install the sink
9. Secure the countertop
Place the countertop on sawhorses. Drill a
To prevent moisture from penetrating the
Fit the countertop back into place on the
Lift off the countertop and turn it upside
Your countertop should be secured as
1/2" hole for the jigsaw blade at all four
countertop, apply a polyurethane seal along
base cabinet. Check that the sink hole is
down, placing it back on your saw horses.
shown using the hardware provided. The
corners of the cut line. Following this same
the cut edges with a paintbrush.
not obstructed by the top frame rails of the
Install the sink according to the sink
slotted brackets allow the counterop to
base cabinet. If it is, you’ll need to trim the
manufacturer’s instructions.
expand and contract normally. Set
cut line, saw the hole for the sink unit.
rails so that the sink will fit properly.
countertops in place, allowing the same
gaps as when you measured. Locate
attachment points at regular intervals and
drill pilot holes before securing the top.
11. Prepare wood countertop for use
12. Assure long-term beauty
If your sink is not pre-drilled for the faucet
Your solid wood countertop from IKEA was
Sand and oil your counterop regularly for
or other fittings, you will need to cut the
pretreated at the factory to condition and
long-term beauty and protection. Stains
necessary holes in the sink. Tape and mark
protect it until installation. To prepare it for
and minor damage can be removed using
a place for each of the fittings. Drill all
use, sand the surface with a fine sandpaper
fine sandpaper. Wipe the sanded surface
holes with the aid of the FIXA tool and
and finish it with IKEA BEHANDLA approved
clean and re-oil the affected area.
install the faucet and fittings following the
wood-block oil.
manufacturer´s instructions.
© Inter IKEA Systems B.V. 2012
10. Install the faucet
Step 6. Install shelves,
drawers and more
Now that the cabinet frames are in place, it’s
time to add shelving, lighting, drawers and
other accessories. All cabinet frames have
predrilled holes for quick and easy installation
of shelving, drawers and other interior
accessories. This also makes it simple to make
adjustments or add accessories later on!
The poster also shows an overview of the
various accessories that can be installed.
For complete details, you’ll need to follow the
instructions included in each package.
The Step 6 poster provides instructions for:
•
•
•
•
•
Installing cover panels
Installing lighting
Fitting shelves
Attaching knobs and handles
Installing drawers
Step
6. In
stal
l sh
elve
s,
draw
ers
&m
ore
Step
7. Ad
d th
e
Whe
n you’
ve com
d Step
Hang
instru these
ctio
the
ns on
wall
so you
hav
e you
r han ’ll
ds
free!
1. Insta
ll cove
Temp
r pane
oraril
y secur
into
ls
place
e the
using
holes
cover
a clam
throu
pane
gh the
from
p. Drill
l
the
cabin
pilot
inside
being
of the et fram
caref
e
cabin
ul not
cover
ets,
pane
to
l. Screw drill throu
into
place
gh the
the
.
cover
pane
l
4. Atta
ch draw
On a
er knob
6” high
knob
draw
s/ha
s and
er front
ndle
hand
front
s
, attac
les to
befor
h
e
the
draw
draw
er box. it is moun
er
ted
to the
Just
som
e of
the
grea
t
6, all
inter
ior cabi
net
acce
ssor
When
ies will
you
be in
’ve
access
plac
com
e.
orie
pred
s will pleted
rilled
Step
be in
hole
6, all
draw
plac
s for
ers
inte
e. The
quic
and
rior
simp
k and
interior
cabi
le to
nets
easy
acce
mak
cab
inet
If you
have
installat
e adju
ssor
need
ies.
ion of
put
This
to atta stments
them
shel
also
or add
ving
on befo ch cove
mak
scre
,
acce
es it
wed
r pan
ssor
on from re doin
ies late
g any els to the
the
r on.
thing
cabi
insid
net
else
e.
fram
, sinc
es,
e they
’re
2. Insta
If cabin ll light
et lighti ing
kitch
en plan, ng is
includ
we sugg
ed
ll it
3. Insta
now.
est that in your
Use
ll shelv
rician
Inser
a
for profe qualified you
t four
es
the
supp
ssion
predr
orts
al resul
illed
per
cabin
ts.
et, then holes insideshelf into
them
each
. Think rest a
shelf
store
abou
, and
t what on top
of
place
make
you
the
best
need
shelv
use
to
es to
of the
space
.
When
you
’ve
kitc
com
hen
plet
is rea
you
ed Ste
dy to
only
p 7,
use
importa have a
you
! It’s
few
almost r new
mor
install nt, so be
IKE
e thin
time
sure
any
to cele A
child
cabi
to take gs left
net
to do!
safe
brat
safe
your
ty devi
e—
But
from
ty
time
they
ces
dangero catches
. Rem
’re
you’
coul
help
emb
ve chos
us hou
d brin
er to
you
seho
en.
g them
Draw
ld chem protect
harm
your
er and
icals
.
child
and
ren
othe
r item
s that
insta
elect
5. Atta
ch draw
Using
er front
the
hardw
s
are
draw
provi
er
throu
ded,
gh the front to
The
moun
draw
holes
predrille the draw
t
ers
. Thes
sturd
er box
y self-c glide smoo
allow
e holes d, preal
of servi
igned
easy
losing
thly
and
adjus
on
draw
the
ce. To
runne
er front
hardw
tmen
open
rs for
set the
t for
are
posit
align
years
perfe
ion,
draw
stops
ment
slide
ct
er in
, then
.
clear
tilt slight it out until the
stor
s the
age
it
ly up
stop
To close
idea
so
point
s...
the
on the it
and
draw
roll
runne
it shut. er tilt
r.
it up
again
1. Saw
toe-k
Caref
icks
ully
meas
kicks
so that ure and
area
mark
they
below
toecover
toe-k
your
the
icks
base
open
to the
cabin
a fine-t
ets.
corre
oothe
Saw
ct lengt
d saw.
h using
2. Atta
ch toe-k
Cove
r the
ick
edgi
cut
ng
edge
the
of the
enclo
sed
toe-k
it on
edgin
icks
with
g
it to
a warm strip.
the
right
iron,
lengt
then
h.
with
Press
stain
on the
into
4. Atta
ch light
Meas
ure,
valan
cut
ces
valan
and
ces
fit the
bene
Instr
light
ath
uctio
the
ns for
wall
place
cabin
insta
ment
ets.
llatio
are
valan
n and
includ
ces.
ed with
Reme
sealin
mber
g strips
the
to attac
.
h
5. Insta
ll corn
Follow
ices
the
insta
includ
llatio
ed with
n instru
resul
the
ts, use
ction
corni
s
the
ce. For
a miter
corne
best
box
rs of
angle
saw
each
. Meas
to cut
corni
ure
ce at
caref
ces
a 45°
will
be the ully so
that
right
lengt
h.
L acces
sorie
steel
s in
.
RATI
ONE
LL interi
draw
or fittin
ers.
7. Fit
the
hing
Inser
e to
t the
the
hinge
predr
door
illed
body
into
as show hole in
the
the
n. No
door
screw
and
press
s are
need
ed.
the
gs for
8. Hang
the
Snap
door
the
s
hinge
plate
body
and
adjus
onto
corre
the
t the
ct positi
base
on, using door to
s. Instr
the
the
uctio
adjus
includ
ed with ns for doing tment
the
this
hinge
s.
screw
are
L acces
6. Atta
ch the
Screw
hing
the
e plate
door
the
hinge
secon
base
d and
plate
at the
third
top
predr
and
illed
botto
m.
into
holes
NDTA
less
BYGE
9. Atta
ch door
Selec
hand
t and
les
meas
the
door
ure
hand
the
temp
posit
les.
late
ion of
for the Use a
point
FIXA
s so
corre
that
ct drillin drill
in the
you
same
can
g
sure
place
to check position
hand
on
les
s befor on which all doors
. Be
side
e you
the
. Hold
mark
door
a block
and
door
of wood drill the
so
n’t splint that the
behin
d
er when surface
throu
gh.
the
drill
bit
open
sorie
s in
powd
holes
er coate
each
does
d steel
.
10.
Atta
ch prot
e self-a
ectiv
e tabs
the
dhes
soun
d when ive tabs
doors
will
you
. You’ll
reduc
close
with
e
find
cabin
the
them
hinge
et
the
s. Peel in the packa
uppe
r and
and
doors
ge
or cabin lower corne stick to
hinge
ets,
rs of
side.
oppo
the
site
the
Thes
RATI
ONE
LL pull-o
it's all
withi
n reach ut baske
ts –
.
goes
IKEA
s B.V.
System
Con
gratula
You’
ve don tions!
e it!
your
Tim
wor
of inge k: a prac e to step
back
tical
niou
, attr
s feat
easi
er for
active and adm
ures
ire
year
that
got
kitch
s to
mor
will
en
did mos e for your come. And make your full
mon
t of
best
life
ey at
the
of all
work
IKEA
you
your
beca
self!
use
you
© Inter
2012
9
3. Clip
Follow toe-kicks
the
into
direc
the
place
toe-k
tions
ick clips.
for attac
one
clip
At corne
hing
facin
down
g up
rs set
– this
and
the
allow
other
s them
same
leg.
both
place
Snap
to fit
.
the
toe-k
icks
cut
each
corni
GRU
© Inter IKEA Systems B.V. 2012
finish
ing
touc
hes
plete
Hang the
poster on
the wall
for Step 6
Step 7. Add the
finishing touches
You’re almost there. Just a few more finishing
touches and your kitchen will be complete.
From attaching knobs and handles to checking
the alignment of doors and drawers once
everything is in place, it’s important to take
your time and get these things right.
l
stal
6. In
Step
ore
&m
ers
draw
ves,
shel
e
d th
7. Ad
Step
e.
in plac
be
inet
ies will
cab
ssor
rior
acce
net
all inte have
,
ving
p 6,
nets
shel
ed Ste The cabi
ion of it
plet
e.
com
plac
installat makes
’ve
easy
r on.
be in
you
also
ies late
When ories will quick and ies. This
es,
ssor
fram
for
ssor
acce
net
access d holes
acce
cabi
or add
’re
the
rille
they
interior
pred
els to
stments
and
since
ers
e adju cover pan g else,
draw
mak
ch
thin
le to
to atta doing any
simp
need
re
e.
If you
on befo the insid
them
put
on from
wed
scre
ior cabi
d Step
inter
6, all
plete
ve com
n you’
Whe
these
Hang
ns on
ctio
’ll
instru ll so you
ds
wa
r han
the
e you
hav
free!
age
the
e of
t stor
ick
ng
edgi
icks
toe-k
of the
e plate
plate
hing
illed
ch the hinge base
predr
door
third
the
m.
d and
Screw
botto
secon
and
the
top
into
at the
holes
6. Atta
ces
valan light
ets.
ch light fit the
cabin
and
4. Atta
wall
cut
the
ure,
n and
ath
Meas
llatio
bene
the
ces
insta
valan
ns for
ed with h
uctio
includ
Instr
are
to attac
ment
mber
place
Reme
ces.
.
valan
g strips
sealin
s
ction
ices
n instru best
ll corn
llatio
ce. For
5. Insta insta
the
corni
to cut
the
saw
Follow
45°
with
box
at a
ded
a miter cornice
inclu
ts, use
each
so that
resul
ully
rs of
h.
caref
corne
lengt
ure
the
. Meas be the right
angle
will
ces
corni
door
the
the
e to
into
hing
press
the
body
and
7. Fit
hinge
door
ed.
t the
in the
need
Inser
hole
s are
illed
screw
predr
n. No
as show
base
s
the
door
onto
the
body
to the
t
8. Hang hinge
door
tmen
the
t the
adjus
Snap
the
adjus
this
and
on, using for doing
plate
ct positi uctions
s.
corre
hinge
the
s. Instr
screw
ed with
includ
are
les
ion of
hand
posit
drill
ch door ure the
a FIXA g
9. Atta
meas
Use
t and
les.
Selec
les
ct drillin
hand
hand
corre
door
place
the
. Be
for the
can
late
you
all doors
temp
that
door
ion on
s so
the
posit
side
point
the
same
on which and drill d
in the
behin
to check you mark
e
sure
wood
s befor block of
ce
a
open
surfa
bit
the
. Hold
drill
holes
the
so that
door
er when
each
splint
n’t
does
gh.
throu
goes
© Inter
or fittin
gs for
e
e tabs
reduc
ectiv
will
et
ch prot ive tabs
Atta
cabin
dhes
ge
close
packa
you
e self-a
the
to
d when them in
soun
stick
find
and
the
. You’ll
rs of
s. Peel
doors
corne
hinge
the
the
lower
site
with
r and
oppo
uppe
ets,
the
or cabin
doors
side.
hinge
10.
Thes
the
ut baske
LL pull-o .
ONE
n reach
RATI
withi
it's all
L acces
sorie
powd
s in
er coate
ts –
ire
adm
and
back
s!
en full
step
tion
kitch
e to
active e your life
gratula it! Tim
Con
e
, attr
mak
you
will
ve don a prac tical
of all
You’
that
you
best
use
work: features
e. And
beca
your
s
com
niou
IKEA
s to
ey at
of inge
year
mon
er for
self!
your
easi
your
e for
work
mor
the
got
t of
did mos
2012
LL interi
ONE
RATI
ers.
draw
the
s in
s B.V.
sorie
System
L acces
NDTA
.
steel
less
stain
IKEA
GRU
BYGE
© Inter IKEA Systems B.V. 2012
s...
idea
grea
som
place
into
hing
icks
attac
toe-k tions for
rs set
direc
At corne other
the
Follow
ick clips. and the
to fit
toe-k
both
g up
the
icks
facin
s them
toe-k
clip
allow
the
one
Snap
– this
leg.
down
same
on the
.
place
into
3. Clip
ch toe-k
on
thly
years
smoo
rs for
glide
ers
runne er in the
draw
losing
draw
it
y self-c set the
until
sturd
it out
ce. To
s
t
so it
slide
r.
of servi
ion,
er front ded, moun
ly up
runne
posit
ch draw are provi
er box
tilt slight on the
open
draw
again
, then
5. Atta
point
hardw
it up
to the
stops
the
stop
igned
er tilt
Using
s the
are
er front
d, preal
draw
clear
draw
hardw
the
predrille
the
each
ct
To close it shut.
gh the holes and
perfe
e
throu
roll
t for
and
. Thes
tmen
.
holes
adjus
ment
easy
align
allow
er front
draw
The
Just
•
•
•
•
•
•
hes
touc
ing
finish
edge
g strip.
2. Atta
cut
then
edgin
r the
sed
iron,
Cove
enclo
a warm
the
toeh.
with
with
icks
lengt
it on
mark
toe-k
and
right
open
Press
the
the
1. Saw measure
it to
Saw
cover
cut
ully
ets.
they
Caref
cabin
h using
so that
base
your
kicks
ct lengt
corre
below
area
to the
icks
d saw.
toe-k
oothe
a fine-t
l
ls
pane
r pane
ll cove e the cover pilot
p. Drill e
1. Insta y secur
oraril
a clam
et fram
Temp
using
cabin
ets,
place
into
gh the
cabin
gh the
throu
of the
throu
l
holes
inside
pane
to drill
the
cover
from
ul not
the
caref
being
l. Screw
pane
cover
.
place
into
s
ndle
s/ha
h
er knob , attac
er
ch draw er front
4. Atta high draw to the draw
6”
les
to the
ted
On a
hand
s and
is moun
knob
e it
befor
front
er box.
draw
The Step 7 poster provides instructions for:
A
IKE
e—
r new
brat
you
to cele
p 7,
’re
time
they
ed Ste
But
almost
plet
to
to do! ember
com
! It’s
’ve
use
gs left
er and
you
. Rem
dy to
e thin
Draw
time
When
en.
is rea few mor
your
ren
chos
hen
a
child
to take you’ve
kitc
have
s that
only
be sure devices
ect your r item
you
prot
ty
othe
nt, so
you
safe
and
help
importa
child
icals
hes
any
chem
install safety catc sehold
net
us hou
.
cabi
gero
harm
dan
from
g them
d brin
coul
into
es
shelf
per
ll shelv
orts
each
supp
3. Insta
of
inside
t four
on top
holes
to
Inser
illed
a shelf
need
predr
your
rest
you
the
ing
ed in
t what es to
et, then
ll light
you
abou
is includ
cabin
shelv
the
2. Insta lighting
. Think
.
est that
et
them
sugg
place
space
fied
If cabin plan, we
, and
of the
a quali results.
store
use
en
Use
al
best
kitch
now.
ssion
make
ll it
insta
for profe
rician
elect
Hang the
poster on
the wall
for Step 7
After all, it’s details like these that will make
your kitchen look as great as it performs day
after day, year after year!
.
d steel
10
Attaching plinths and mouldings
Attaching light decor strips
Installing cornices
Hanging doors
Attaching knobs and handles
Attaching plastic buffers
Step 6. Install shelves, drawers & more
Step 7. Add the finishing touches
When you’ve completed Step 6, all interior cabinet accessories will be in place.
When you’ve completed Step 7, your new IKEA kitchen is ready to use!
The cabinets have predrilled holes for quick and easy
installation of shelving, drawers and interior accessories.
This also makes it simple to make adjustments or add
accessories later on. If you need to attach cover panels to
the cabinet frames, put them on before doing anything
else, since they’re screwed on from the inside.
It’s almost time to celebrate—you only have a few more things left to do! But they’re
important, so be sure to take your time. Remember to install any child safety devices
you’ve chosen. Drawer and cabinet safety catches help you protect your children from
dangerous household chemicals and other items that could bring them harm.
1. Install cover panels
2. Install lighting
3. Install shelves
1. Saw toe-kicks
2. Attach toe-kick edging
3. Clip toe-kicks into place
Temporarily secure the cover panel
If cabinet lighting is included in your
Insert four supports per shelf into
Carefully measure and mark toe-
Cover the cut edge of the toe-kicks
Follow the directions for attaching
into place using a clamp. Drill pilot
kitchen plan, we suggest that you
the predrilled holes inside each
kicks so that they cover the open
with the enclosed edging strip.
the toe-kick clips. At corners set
holes through the cabinet frame
install it now. Use a qualified
cabinet, then rest a shelf on top of
area below your base cabinets. Saw
Press it on with a warm iron, then
one clip facing up and the other
from the inside of the cabinets,
electrician for professional results.
them. Think about what you need to
toe-kicks to the correct length using
cut it to the right length.
down—this allows them both to fit
being careful not to drill through the
store, and place the shelves to
a fine-toothed saw.
cover panel. Screw the cover panel
make best use of the space.
Hang these
instructions on
the wall so
you’ll have your
hands free!
on the same leg. Snap the toe-kicks
into place.
into place.
4. Attach drawer knobs/handles
5. Attach drawer fronts
The drawers glide smoothly on
4. Attach light valances
5. Install cornices
6. Attach the hinge plate
On a 6" high drawer front, attach
Using the hardware provided, mount
sturdy self-closing runners for years
Measure, cut and fit the light
Follow the installation instructions
Screw the door hinge base plate
knobs and handles to the drawer
each drawer front to the drawer box
of service. To set the drawer in the
valances beneath the wall cabinets.
included with the cornice. For best
into the second and third predrilled
front before it is mounted to the
through the pre­drilled, prealigned
open position, slide it out until it
Instructions for installation and
results, use a miter box saw to cut
holes at the top and bottom.
drawer box.
holes. These holes and the hardware
stops, then tilt slightly up so it
placement are included with the
the corners of each cornice at a 45°
allow easy adjustment for perfect
clears the stop point on the runner.
valances. Remember to attach
angle. Measure carefully so that
drawer front alignment.
To close the drawer tilt it up again
sealing strips.
cornices will be the right length.
7. Fit the hinge to the door
8. Hang the doors
9. Attach door handles
Insert the hinge body into the
Snap the hinge body onto the base
Select and measure the position of
predrilled hole in the door and press
plate and adjust the door to the
the door handles. Use a FIXA drill
as shown. No screws are needed.
correct position, using the adjustment
template for the correct drilling
screws. Instructions for doing this
points so that you can place handles
are included with the hinges.
in the same position on all doors. Be
and roll it shut.
Just some of the great storage ideas...
sure to check on which side the door
GRUNDTAL accessories in
RATIONELL interior fittings for
stainless steel.
the drawers.
opens before you mark and drill the
holes. Hold a block of wood behind
each door so that the surface
doesn’t splinter when the drill bit
goes through.
These self-adhesive tabs will reduce
the sound when you close cabinet
doors. You’ll find them in the package
with the hinges. Peel and stick to
the upper and lower corners of the
BYGEL accessories in powder coated steel.
RATIONELL pull-out baskets –
doors or cabinets, opposite the
it's all within reach.
hinge side.
Congratulations!
You’ve done it! Time to step back and admire your work:
a practical, attractive kitchen full of ingenious features
that will make your life easier for years to come. And best
of all you got more for your money at IKEA because you
did most of the work yourself!
© Inter IKEA Systems B.V. 2012
10. Attach protective tabs
Now, enjoy your
new kitchen!
You’ve done it!
Time to step back and admire your work: a
practical, attractive kitchen full of ingenious
features designed to make your life easier
every day. Best of all, you got more for your
money at IKEA because you did a lot of the
work yourself. With just a little care and
maintenance, your new IKEA kitchen will
keep looking its best for years to come.
Keeping sinks shining
Stainless steel sinks should be cleaned with
a mild detergent and sponge, then rinsed
thoroughly and wiped dry. Be sure to clean
in the direction of the metal’s grain. Never
use steel wool, steel brushes, bleaching or
scouring powders on a stainless steel sink.
Avoid cleaning silver on the sinktop, since
this may discolour it.
Caring for your cabinets
Clean the doors, cabinet interiors and wood
surfaces with a soft, damp cloth using cleaning
products intended for these materials. After
cleaning, wipe down with a clean dry cloth.
DO NOT use cleaning agents that contain
ammonia, alcohol or abrasives.
For care of solid wood countertops,
see poster Step 5.
© Inter IKEA Systems B.V. 2012
11