Compliance Table for C2I2 Systems
Compliance Table for C²I² Systems' PMC FDDI DAS Network Interface Card
(NIC)
Compliance Table in PDF-format.
Requirement
Compliance
Specification
ANSI X3T9.5
Yes
Complies to ANSI X3T9.5 and X3T12.
Locations for 64 CAM Addresses
No
The AMD Supernet III chipset provides for 32 Multicast Address
Entries in the Address Filter (AF). Each entry consists of a
48-bit comparand, a 48-bit mask and a 6-bit ‘personality’.
SMT V7.3
Yes
Comply.
Dual ST Connectors
Yes
Dual FDDI ST receptacles provided on the DAS version.
AMD FDDI Chipset
Yes
AMD Supernet III chipset used.
Support for Dual-Homing Configuration
Yes
Dual-Homing and Alternate Path Configurations supported.
Synchronous and Asynchronous
Bandwidth
Yes
SBA and ESS supported in addition to Asynchronous
bandwidth.
LynxOS V3.0 driver support
We do not have a LynxOS drivers available at present.
C²I² Systems could supply LynxOS drivers 4 months after order
as we already have similar drivers for VxWorks.
AIX V4.2/3 driver support
Yes
Supplied on request.
Windows NT V4.0 support
Yes
Supplied on request.
Temperature Operating:
Yes
Tested from -15 C to +71 C in a thermal chamber, with no
forced air over the card, only normally circulating air in the
chamber.
0 C to +55 C (ambient)
Refer to Item No 30.
Relative Humidity Operating :
0 % to 95 % Non-Condensating
Yes
Altitude Operating :
-300 m to +3 000 m
Yes
Operating altitude capable of +9 000 m (30 000 ft).
Temperature Non-Operating :
-40 C to +85 C
Yes
Refer to Item No 11: Operating Temperature.
Relative Humidity Non-Operating :
0 % to 95 % Non-Condensating
Yes
Altitude Non-Operating :
-300 m to +19 000 m
Yes
Shock :
20 g for 11 ms
Yes
Tested to: 30 g for 11 ms (half sine shock pulses).
Vibration :
5 to 500 Hz at 2 g
Yes
Tested to:
- Sine: 10 g (peak) 15 to 2 kHz
- Sweep duration 10 minutes per axis
- Random: 0,04 g 2/Hz at 15 to 2 kHz
Page 1
Compliance Table for C2I2 Systems
- 60 minutes per axis
Inclination :
0° ±180°
Yes
PMC FDDI DAS not affected.
Noise :
Standard Commercial
Yes
Operational warm-up time :
0 seconds
Yes
PMC FDDI DAS operational immediately after power supplied.
Air Flow Requirement :
96 m (linear) per minute
Yes
Refer to Item No. 11: Operating Temperature.
Our PMC FDDI DAS board can operate within the
temperatures required without forced-air.
Link Confidence (LC) test parameter in
drivers to be supplied with LC_Short =
5 ms
(** Refer to note at end of Appendix)
Yes
LynxOS Driver will be changed per user requirement.
AIX Driver will be modified if required by the user, but will be
dependent on an NRE charge as driver source code needs to
be purchased and modified.
Windows NT Driver will be modified if required by the user, but
will be dependent on an NRE charge as driver source code
needs to be purchased and modified.
Additional Supporting Information
PCI Compatibility
32-bit PCI-Bus electrical, complies to PCI Rev. 2.1
PMC Compatibility
PMC form-factor, complies to CMC IEEE P1386.1
Optical Bypass
Optical Bypass Switch (OBS) Control provided.
OBS Connector
Hirose 6-pin connector.
MTBF
Figures according to MIL-HDBK-217F, Parts Count Method :
Ground Mobile
T j = 65 C, T a = 45 C
19 000 hours
Naval, Sheltered
T j = 60 C, T a = 40 C
26 000 hours
Airborne, Inhabited Cargo
T j = 75 C, T a = 55 C
20 000 hours
Power Requirements
< 1,45 A @ 5 V
Typical Driver Throughput Performance > 8 Mbyte/s (>56 Mbit/s)
(VxWorks on DY4 SVME-179)
One of our customers has measured in excess of 9 Mbyte/s (72 Mbit/s).
Extended Operating Temperatures with Tested from -40 C to +81C in a thermal chamber, with no forced-air over
Industrial Grade Components
the card, only normally circulating air in the chamber.
Page 2