Standards Council of Canada
Conseil canadien des normes
600-55 Metcalfe Street
Ottawa, ON K1P 6L5
Canada
55, rue Metcalfe, bureau 600
Ottawa, ON K1P 6L5
Canada
SCOPE OF ACCREDITATION
Canadian Standards Association
CSA Group - Toronto
178 Rexdale Boulevard
Etobicoke, ON
M9W 1R3
Accredited Laboratory No. 12
(Conforms with requirements of CAN-P-4E (ISO/IEC 17025:2005))
CONTACT:
TEL:
EMAIL:
URL:
Benjamin Barker
(416)-747-4013 Ext::44013
benjamin.barker@csagroup.org
http://www.csagroup.org/
CLIENTS SERVED:
All interested parties
FIELDS OF TESTING:
Chemical/Physical, Electrical/Electronic, Mechanical/Physical,
Optics & Optical Radiation
SCOPE ISSUED ON:
2016-04-26
ACCREDITATION
VALID TO:
2017-08-15
The following is a Scope of Accreditation for which this testing laboratory has been accredited to ISO/IEC
17025:2005. Note that the parent organization is also accredited as a certification body. The parent
organization’s Scope of Accreditation for certification activities may be broader than the listing of standards
and test methods that appear below. Refer to the parent organization’s Scope of Accreditation granted by the
SCC for certification activities found at:
http://www.scc.ca/en/accreditation/product-process-and-service-certification/directory-of-accredited-clients
Where standards, such as product standards, are listed below, the laboratory is considered accredited only for
the testing elements in those standards.
CONSTRUCTION
Standards Council of Canada
1
Standards Council of Canada Accredited Laboratory No. 12
Construction Materials : (Excluding textile products)
Plumbing Products (See also ELAS,METAL and NONMETAL Sections)
(Ducting and Fittings, Electrical and Electronic)
(Fittings, Plumbing, Supply and Waste)
(Handling Equipment, Gaseous Fuels)
(Pipe, Soil)
(Plumbing Fixtures)
(Plumbing Systems)
(Sewage and Waste Handling Equipment)
(Water Handling Equipment)
(Water Handling Equipment, Potable)
(Vacuum Breakers and Backflow Preventers)
ASME A112.18.1/CSA B125.1
ASME A112.18.2/CSA B125.2
ASME A112.18.6/CSA B125.6
ASME A112.19.1/CSA B45.2
ASME A112.19.2/CSA B45.1
ASME A112.19.3/CSA B45.4
CSA B125.3
CSA B127.1
CSA B137.0
CSA B137.1
CSA B137.10
CSA B137.11
CSA B137.16
SCOPE OF ACCREDITATION
Plumbing Supply Fittings
Except for: Clause 5.6 Life Cycle
Scope Limitation – Life cycle testing is performed at CSA
Group, 8501 East Pleasant Valley Road, Independence,
OH, 44131-5516 USA
Plumbing Waste Fittings
Flexible Water Connectors
Enamelled Cast Iron and Enamelled Steel Plumbing Fixtures
Ceramic Plumbing Fixtures
Stainless Steel Plumbing Fixtures
Plumbing Fittings
Components for Use in Asbestos Cement Drain, Waste and
Vent Systems
Definitions, General Requirements, and Methods of Testing for
Thermoplastic Pressure Piping
Polyethylene Pipe, Tubing and Fittings for Cold Water
Pressure Services
Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene
Composite Pressure Pipe Systems
Except for: Clauses Adhesion Test and Thermocycling
Polypropylene (PP-R) Pipe and Fittings for Pressure
Applications
Recommended Practice for the Installation of CPVC Piping for
Hot and Cold Water Distribution Systems
2
Standards Council of Canada Accredited Laboratory No. 12
CSA B137.3
CSA B137.4
CSA B137.4.1
CSA B137.5
CSA B137.6
CSA B137.8
CSA B137.9
CSA B181.1
CSA B181.2
CSA B181.3
CSA B182.1
CSA B182.2
CSA B182.4
CSA B182.6
CSA B196.3
CSA B272
CSA B45.0
CSA B45.5
CSA B45.6
CSA B45.7
CSA B64.0
CSA B64.1.1
CSA B64.1.2
CSA B64.2
CSA B64.2.1
SCOPE OF ACCREDITATION
Rigid Polyvinyl Chloride (PVC) Pipe for Pressure Applications
Except for: the follow for Sizes over NPS 24: 4.7.1
Flattening,Impact, Flattening, Heat Reversion in PVC Moulded
Fittings, Spark Test Except Heat Reversion in PVC Moulded
Fittings for over NPS 8
Polyethylene Piping Systems for Gas Services
Except for: Clause 3.3.3.5 - Chemical Resistance
Electrofusion-Type Polyethylene Fittings for Gas Services
Except for: Clause 4.4 - Impact Test for Saddle Type Joints
Cross-linked Polyethylene (PEX) Tubing for Pressure
Applications
CPVC Pipe, Tubing, and Fittings for Hot and Cold Water
Distribution Systems
Polybutylene (PB) Piping for Pressure Applications
Except for: Metal Components of mechanical fittings
Polyethylene/Aluminum/Polyethylene Composite Pressure
Pipe Systems
Except for: Clauses Adhesion Test and Thermocycling
ABS Drain, Waste and Vent Pipe and Pipe Fittings
PVC Drain, Waste, and Vent Pipe and Pipe Fittings
Except for: Dimensional Stability Test over NPS 6 Cycling
Test, Breakaway Force Test Oand Offset Test for Piston-Type
Expansion Joints other than Type 1
Polyolefin Laboratory Drainage Systems
Plastic Drain and Sewer Pipe and Pipe Fittings
PVC Sewer Pipe and Fittings (PSM Type)
Profile PVC Sewer Pipe and Fittings
Profile Polyethylene Sewer Pipe and Fittings
PVC Underground Telecommunication Cable Ducting and
Fittings
Prefabricated Self-Sealing Vent Flashings
CSA Standards on Plumbing Fixtures
Double Check Valve (DCVA) Backflow Preventers
Non-recirculating Toilets and Waste Holding Tanks for Use in
Recreational Vehicles
Self-Contained, Recirculating, Chemically Controlled Toilets
for Use in Recreational Vehicles
Definitions, General Requirements, and Test Requirements for
Vacuum Breakers and Backflow Preventers
Atmospheric Vacuum Breakers (AVB)
Except for: over 1" Pipe Size
Pressure Vacuum Breakers (PVB)
Except for: over 1" Pipe Size.
Hose Connection Vacuum Breakers (HSVB)
Except for: over 1" Pipe Size.
Hose Connection Vacuum Breakers (HCVB) with Manual
Draining Feature
3
Standards Council of Canada Accredited Laboratory No. 12
CSA B64.2.2
CSA B64.3
CSA B64.4
CSA B64.5
CSA B64.6
CSA B64.7
CSA B64.8
CSA B70
CSA B79
IAPMO PS 49
IAPMO TSC 1
IAPMO TSC 11
IAPMO TSC 14
IAPMO TSC 15
IAPMO TSC 2
IAPMO TSC 20
IAPMO TSC 21
IAPMO TSC 22
IAPMO TSC 23
IAPMO TSC 30
IAPMO TSC 4
IAPMO TSC 7
IAPMO TSC 8
SCOPE OF ACCREDITATION
Except for: over 1" Pipe Size.
Hose Connection Vacuum Breakers (HCVB) With Automatic
Draining Feature
Except for: over 1" Pipe Size.
Reduced Pressure Principle (RP) Backflow Preventers
Except for: over 1" Pipe Size.
Backflow Preventers, Reduced Pressure Principle Type (RP)
Except for: over 1" Pipe Size.
Backflow Preventers, Double Check Valve Type (DCVA)
Except for: over 1" Pipe Size.
Backflow Preventers - Dual Check Valve Type
Except for: over 1" Pipe Size.
Vacuum Breakers - Laboratory Faucet Type
Except for: over 1" Pipe Size.
Dual Check Valve Backflow Preventers with Intermediate
Vent (DuCV)
Except for: over 1" Pipe Size.
Cast Iron Soil Pipe, Fittings, and Means of Joining
Floor Drains and Trench Drains
Backflow Prevention Requirements for Fixture Fittings with
Hose Connected Singular Moveable Outlets
Mechanical Seal Toilets for Use in Recreational Vehicles
Non-Metallic Shower Receptors, Shower Stalls, Lavatories,
Bathtubs and Step Tub/Shower Combination Waste Holding
Tank and Shower Receptor Units
Electric Water Pumps for use in Recreational Vehicles
Hand Actuated Hand Pumps
Waste Holding Tanks
Stainless Steel Plumbing Fixtures for Use in Recreational
Vehicles
Backflow Preventers with Flexible Shower and Shampoo
Hoses
Porcelain Enameled Formed Steel Plumbing Fixtures
Detachable Liquid Waste Holding Tank
Termination Valves for use in Recreational Vehicles
Pressurized and Non-Pressurized Potable Water Tanks for Use
in Recreational Vehicles
Non-Pressure Water Tubing or Piping for Use in Recreational
Vehicle
Backflow Preventers and Relief Valves
4
Standards Council of Canada Accredited Laboratory No. 12
ELECTRICAL PRODUCTS AND ELECTRONIC PRODUCTS
(Electromagnetic Compatibility)
ANSI C63.4
CISPR 14-2
CISPR 15
CISPR 16-2-1
CISPR 16-2-3
CISPR 20
CISPR 24
CSA C108.3.1
CSA C108.4
CSA C108.8
EN 12015
EN 12016
EN 55014-1
EN 55014-2
EN 55015
EN 55020
SCOPE OF ACCREDITATION
American National Standard for Methods of Measurement of
Radio-Noise Emissions from Low-Voltage Electrical and
Electronic Equipment in the Range of 9 kHz to 40 GHz
Electromagnetic Compatibility - Requirements for Household
Appliances, Electric Tools and Similar Apparatus - Part 2:
Immunity Product Family Standard
Limits and methods of measurement of radio disturbance
characteristics of electrical lighting and similar equipment
Specification for Radio Disturbance and Immunity
Measuring Apparatus and MethodsPart 2-1: Methods of Measurements of Disturbances and
Immunity
-Conducted Disturbance Measurements
Specification for Radio Disturbance and Immunity
Measuring Apparatus and MethodsPart 2-3: Methods of Measurements of Disturbances and
Immunity
- Radiated Disturbance Measurements
Limits and Methods of Measurement of Immunity
Characteristics of Sound and Television Broadcast Receivers
and Associated Equipment
Information Technology Equipment - Immunity Characteristics
- Limits and Methods of Measurement
Limits and Measurement Methods of Electromagnetic Noise
from AC Power Systems, 0.15-30 MHz
Limits and Methods of Measurement of Radio Interference
Characteristics of Vehicles, Motor Boats, and Spark-Ignited
Engine-Driven Devices
Electromagnetic Emissions from Data Processing Equipment
and Electronic Office Machines
Electromagnetic Compatibility - Product Family Standard for
Lifts, Escalators and Passenger Conveyers- Emission
Electromagnetic Compatibility - Product Family Standard for
Lifts, Escalators and Passenger Conveyers - Immunity
Electromagnetic Compatibility - Requirements for Household
Appliances, Electric Tools and Similar Apparatus - Part 1:
Emissions Product Family Standard
Electromagnetic Compatibility - Requirements for Household
Appliances, Electric Tools and Similar Apparatus - Part 2:
Immunity Product Family Standard
Limits and Methods of Measurement of Radio Disturbance
Characteristics of Electrical Lighting and Similar Equipment
Electromagnetic Immunity of Broadcast Receivers and
Associated Equipment
5
Standards Council of Canada Accredited Laboratory No. 12
EN 55024
EN 55103-2
EN 60947-4-1
EN 61000-3-2
EN 61000-3-3
EN 61000-4-11
EN 61000-4-12
EN 61000-4-13
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-9
EN 61000-6-1
EN 61000-6-2
SCOPE OF ACCREDITATION
Information Technology Equipment - Immunity
Characteristics-Limits and Methods of Measurement
Electromagnetic Compatibility - Product Family Standard for
Audio, Video, Audio-Visual and Entertainment Lighting
Control Apparatus for Professional Use - Part 2: Immunity
Low-Voltage Switchgear and Controlgear - Part 4: Contactors
and Motor-Starters - Section 1: Electromechanical Contactors
and Motor Starters
Electromagnetic Compatibility (EMC) - Limits - Limits for
Harmonic Current Emissions (Equipment Input Current <<+16
A Per Phase)
Electromagnetic Compatibility (EMC) - Limits - Limitation of
Voltage Fluctuations and Flicker in Low-Voltage Supply
Systems for Equipment With Rated Current << 16 A
Electromagnetic Compatibility (EMC) -Testing and Measuring
Techniques - Voltage Dips, Short Interruption, and Voltage
Variations Immunity Tests
Electromagnetic Compatibility (EMC) - Part 4-12: Testing and
Measurement Techniques - Ring Wave Immunity Test
Electromagnetic Compatibility (EMC) - Part 4-13: Testing and
Measurement Techniques - Harmonics and Interharmonics
Including Mains Signalling at A.C. Power Port, Low
Frequency Immunity Tests
Electromagnetic Compatibility (EMC) -Testing and
Measurement Techniques - Electrostatic Discharge Immunity
Test and Basic EMC Publication
Electromagnetic Compatibility (EMC) - Testing and
Measurement Techniques - Radiated, Radio - Frequency,
Electromagnetic Field Immunity Test
Electromagnetic Compatibility (EMC) -Testing and
Measurement Techniques - Electrical Fast Transient/Burst
Immunity Test and Basic EMC Publication
Electromagnetic Compatibility (EMC) - Testing and
Measurement Techniques - Surge Immunity Test
Electromagnetic Compatibility (EMC) - Testing and
Measurement Techniques - Immunity to Conducted
Disturbances, Induced by Radio-Frequency Fields
Electromagnetic Compatibility - Testing and Measurement
Techniques - Power Frequency Magnetic Field Immunity
Test-Basic EMC Publication
Electromagnetic Compatibility - Testing and Measuring
Techniques - Pulse Magnetic Field Immunity Test - Basic
EMC Publication
Electromagnetic Compatibility (EMC) - Part 6: Generic
Standards - Section 1: Immunity for Residential, Commercial
and Light-Industrial Environments
Electromagnetic Compatibility (EMC) - Part 6: Generic
Standards - Section 2: Immunity for Industrial Environments
6
Standards Council of Canada Accredited Laboratory No. 12
EN 61326
EN 61543
EN 61547
EN298
ENV 50204
ETSI EN 301 489-1
ETSI EN 301 489-4
FCC MP-5
FCC Part 15 Class A & B
FCC Part 18 Consumer & nonConsumer
ICES-001
ICES-003
IEC 601-1-2
IEC 60601-1-3
IEC 60601-2-43
IEC 60601-2-54
IEC 60730-2-5
IEC 60945
Electrical Equipment for Measurement, Control and Laboratory
Use - EMC Requirements
Residual Current - Operated Protective Devices (RCDs) for
Household and Similar Use - Electromagnetic Compatibility
Equipment for General Lighting Purposes - EMC Immunity
Requirements
Automatic gas burner control systems for gas burners and gas
burning appliances with or without fans
Radiated Electromagnetic Field from Digital Radio Telephones
- Immunity Test
Electromagnetic Compatibility and Radio Spectrum Matters Electromagnetic Compatibility (EMC) Standard for Radio
Equipment and Services - Part 1: Common Technical
Requirements
Electromagnetic Compatibility and Radio Spectrum Matters Electromagnetic Compatibility (EMC) Standard for Radio
Equipment and Services - Part 4: Specific Conditions for Fixed
Radio Links and Ancillary Equipment and Services
FCC Methods of Measurements of Radio Noise Emissions
from Industrial, Scientific, and Medical Equipment
Title 47--Telecommunication - Chapter I--Federal
Communications Commission - Part 15--Radio Frequency
Devices for Class B only.
Title 47--Telecommunication - Chapter I--Federal
Communications Commission - Part 18--Industrial, Scientific,
and Medical Equipment
Industrial, Scientific and Medical Radio Frequency Generators
Digital Apparatus limited to class B devices using only C63.4
test methods.
Medical electrical equipment - Part 1: General requirements for
safety - 2. Collateral Standards: Electromagnetic compatibility
- Requirements and tests
Medical Electrical Equipment-Part 1-3: General Requirements
for Basic Safety and Essential Performance - Collateral
Standard: Radiation Protection in Diagnostic X-Ray Equipment
Medical Electrical Equipment-Part 2-43: Particular
Requirements for the Basic Safety and Essential Performance
of X-Ray Equipment for Interventional Procedures
Medical Electrical Equipment-Part 2-54: Particular
Requirements for the Basic Safety and Essential Performance
of X-Ray Equipment for Radiography and Radioscopy
Automatic Electrical Controls for Household and Similar Use
Maritime Navigation and Radio communication Equipment and
Systems - General Requirements - Methods of Testing and
Required Test Results
Except for: Clauses: 8.7 Vibration 8.12 Corrosion (Salt Mist)
11.2 Compass Safe Distance
IEC 60947-4-1
SCOPE OF ACCREDITATION
7
Standards Council of Canada Accredited Laboratory No. 12
IEC 61000-3-2
IEC 61000-3-3
IEC 61000-4-11
IEC 61000-4-12
IEC 61000-4-13
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-9
IEC 61000-6-1
IEC 61000-6-2
IEC 61326
IEC 61543
SCOPE OF ACCREDITATION
Low-Voltage Switchgear and Control Gear - Part 4: Contactors
and Motor-Starters-Section 1: Electromagnetic Contactors and
Motor-Starters
Electromagnetic Compatibility (EMC)-Part 3 Limits- Section
2: Limits of Harmonic Current Emission(Equipment Input
Current Up To and Including 16A per Phase)
Electromagnetic Compatibility (EMC) - Part 3: Limits- Section
3: Limitation of Voltage Fluctuations and Flicker in
Low-Voltage Supply Systems for Equipment with Rated
Current Up To 16A
Electromagnetic Compatibility (EMC) - Part4: Testing and
Measurement Techniques - Section 11: Voltage Dips, Short
Interruptions and Voltage Variations Immunity Tests
Electromagnetic Compatibility (EMC) - Part 4-12: Testing and
Measurement Techniques - Oscillatory Waves Immunity Test
Electromagnetic Compatibility (EMC)-Part 4-13: Testing and
Measurement Techniques - Harmonics and Interharmonics
Including Mains Signaling at A.C. Power Port, Low Frequency
Immunity Tests
Electromagnetic Compatibility (EMC) - Part 4: Testing and
Measurement Techniques - Section 2: Electrostatic Discharge
Immunity Test
Electromagnetic Compatibility (EMC) - Part 4: Testing and
Measurement Techniques-Section 3: Radiated,
Radio-Frequency, Electromagnetic Field Immunity Test
Electromagnetic Compatibility (EMC) - Part 4: Testing and
Measurement Techniques - Section 4: Electrical Fast
Transient/Burst Immunity Test
Electromagnetic Compatibility (EMC) - Part 4: Testing and
Measurement Techniques - Section 5: Surge Immunity Test
Electromagnetic Compatibility (EMC) - Part 4: Testing and
Measurement Techniques-Section 6: Immunity to Conducted
Disturbances, Induced by Radio Frequency Fields
Electromagnetic Compatibility (EMC) - Part 4: Testing and
Measurement Techniques - Section 8: Power Frequency
Magnetic Field Immunity Test
Electromagnetic Compatibility (EMC) - Part 4: Testing and
Measurement Techniques - Section 9: Pulse Magnetic Field
Immunity Test
Electromagnetic Compatibility (EMC) - Part 6: Generic
Standards - Section 1: Immunity for Residential Commercial
and Light Industrial Environments
Electromagnetic Compatibility (EMC) - Part 6: Generic
Standards - Section 2: Immunity for Industrial Environments
Electrical Equipment for Measurement, Control and Laboratory
Use - EMC Requirements
Residual Current - Operated Protective Devices (RCDs) for
Household and Similar Use - Electromagnetic Compatibility
8
Standards Council of Canada Accredited Laboratory No. 12
IEC 61547
KN 61000-4-11
KN 61000-4-2
KN 61000-4-3
KN 61000-4-4
KN 61000-4-5
KN 61000-4-6
KN 61000-4-8
KN24
Equipment for General Lighting Purposes - EMC Immunity
Requirements
Voltage Dips, Short Interruptions and Voltage Variations
Immunity Tests
Electrostatic Discharge Immunity Test
Radiated, Radio-Frequency, Electromagnetic Field Immunity
Test
Electrical Fast Transient/Burst Immunity Test
Surge Immunity Test
Immunity to Conducted Disturbances, Induced by
Radio-Frequency Fields
Power Frequency Magnetic Field Immunity Test
Information Technology Equipment - Immunity Characteristics
- Limits and Methods of Measurements
(Elevator Equipment)
CAN/CSA B355
CAN/CSA B44
CAN/CSA B44.1/ ASME-A17.5
CAN/CSA B613
Elevating Devices for the Handicapped
Safety Code for Elevators
Elevator and Escalator Electrical Equipment
Elevating Devices for the Handicapped in Private Residences
Communications Equipment and Systems:
CSA C22.2 No 225
Telecommunication Equipment
Power and Signal Distribution Equipment
(Wiring and Related Products)
C22.2 No. 18.2
CSA C22.2 0.3
CSA C22.2 0.5
CSA C22.2 123
CSA C22.2 124
CSA C22.2 126
CSA C22.2 127
CSA C22.2 129
CSA C22.2 130
SCOPE OF ACCREDITATION
Nonmetallic outlet boxes
Test Methods for Electrical Wires and Cables
Threaded Conduit Entries
Aluminum Sheathed Cables
Except for: FT4
Mineral-Insulated Cable
Except for: FT4
Cable Tray Systems
Except for: FT4
Equipment Wires
Neutral Supported Cable
Requirements for Electrical Resistance Heating Cables and
Heating Device Sets
Except for: Clauses 6.2.1.5 Partial Toxicity test in Appendix
B.1
9
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 130.1
CSA C22.2 130.2
CSA C22.2 131
CSA C22.2 153
CSA C22.2 158
CSA C22.2 179
CSA C22.2 18.1
CSA C22.2 18.3
CSA C22.2 18.4
CSA C22.2 18.5
CSA C22.2 182.1
CSA C22.2 182.2
CSA C22.2 182.3
CSA C22.2 182.4
CSA C22.2 188
CSA C22.2 19
CSA C22.2 190
CSA C22.2 198
CSA C22.2 198.2
CSA C22.2 198.3
CSA C22.2 203
CSA C22.2 203.1
CSA C22.2 208
CSA C22.2 21
CSA C22.2 210.2
CSA C22.2 211.0
CSA C22.2 211.1
CSA C22.2 211.2
CSA C22.2 211.3
CSA C22.2 214
CSA C22.2 222
SCOPE OF ACCREDITATION
Heat-Tracing Cable Systems for Use in Industrial Locations
Heat-Tracing Cable Systems for Use in other than Industrial
Locations
Type TECK 90 Cable
Except for: FT4
Quick-Connect Terminals
Terminal Blocks
Airport Series Lighting Cables
Metallic Outlet Boxes
Conduit, Tubing, and Cable Fittings
Hardware for Support of Conduit, Tubing, and Cable Fittings
Positioning Devices
Except for: Smoke and Release Test
Industrial Type, Special Use Attachment Plugs, Receptacles,
and Connectors
Industrial Locking Type, Special Use Attachment Plugs,
Receptacles, and Connectors
Special Use Attachment Plugs, Receptacles, and Connectors
Plugs, Receptacles, and Connectors for Communication
Systems
Splicing Wire and Cable Connectors
Construction and Test of Soldering Lugs
Capacitors for Power Factor Correction
Only for: Clause 4.2.10 (Temperature Test) and for Clause
7.7.4.7 (Dielectric Test)
Extruded Insulating Tubing
Underground Cable Splicing Kits
Coated Electrical Sleeving
Modular Wiring Systems for Office Furniture
Manufactured Wiring Products
Fire Alarm and Signal Cable
Except for: FT4 and Fire Rating
Cord Sets and Power-Supply Cords
Appliance Wiring Material Products
General Requirements and Methods of Testing for Nonmetallic
Conduit
Rigid Types EB1 and DB2/ES2 PVC Conduit
Rigid PVC (Unplasticized) Conduit
Except for: FT4
Rigid Reinforced Thermoset (RE) Conduit and Associated
Fittings
Except for: FT4
Communications Cables
Except for: FT4
Type FCC Under-Carpet Wiring System
Except for: FT4
10
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 227.1
CSA C22.2 227.2
CSA C22.2 227.3
CSA C22.2 230
CSA C22.2 232
CSA C22.2 233
CSA C22.2 239
CSA C22.2 244
CSA C22.2 245
CSA C22.2 26
CSA C22.2 27
CSA C22.2 34
CSA C22.2 35
CSA C22.2 38
CSA C22.2 40
CSA C22.2 42
CSA C22.2 42.1
CSA C22.2 43
CSA C22.2 44
CSA C22.2 45
CSA C22.2 45.1
CSA C22.2 48
CSA C22.2 49
CSA C22.2 51
CSA C22.2 52
CSA C22.2 56
SCOPE OF ACCREDITATION
Electrical Nonmetallic Tubing
Except for: FT4
Flexible Liquid-Tight Nonmetallic Conduit
Except for: FT4
Flexible Nonmetallic Tubing
Except for: FT4
Tray Cables
Except for: FT4
Optical Fiber Cables
Except for: FT4
Cords and Cord Sets for Communication Systems
Control and Instrumentation Cables
Except for: FT4
Switchboards
Marine Shipboard Cable
Construction and Test of Wireways, Auxiliary Gutters and
Associated Fittings
Busways
Except for: 8.2.1 Verification of temperature-rise limits over
3KA
8.2.3.1 Short Circuit over 10KA
8.2.1.4 Temperature rise limits (heat cycling method) over 3kA
8.2.5.1 Verification of mechanical operation over 3kA
8.2.10 Verification of metallic coating finish thickness
Electrode Receptacles, Fittings, and Connectors for Gas Tubes
Extra-Low-Voltage Control Circuit Cables, Low-Energy
Control Cable, and Extra-Low-Voltage Control Cable
Except for: FT4
Thermoset Insulated Wires and Cables
Cutout, Junction, and Pull Boxes
General Use Receptacles, Attachment Plugs, and Similar
Devices
Cover Plates for Flush-Mounted Wiring Devices
Lampholders
Construction and Test of Flexible Non-Metallic Tubing
Rigid Metal Conduit
Electrical Rigid Metal Conduit - Steel
Nonmetallic Sheathed Cable
Flexible Cords and Cables
Armoured Cable
Except for: FT4
Service - Entrance Cables
Except for:
Cl 6.13.2 Vertical flame test - Cables in cable tray - FT4
Flexible Metal Conduit and Liquid-Tight Flexible Metal
Conduit
Except for: FT4
11
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 57
CSA C22.2 62
CSA C22.2 62.1
CSA C22.2 65
CSA C22.2 75
CSA C22.2 76
CSA C22.2 79
CSA C22.2 8
CSA C22.2 80
CSA C22.2 82
CSA C22.2 83
CSA C22.2 83.1
CSA C22.2 85
CSA C22.2 96
CSA C22.2 96.1
CSA C22.2 No. 2459
CSA C22.2 60320-1
UL 1659
UL 1673
UL 1686
UL 543
Appliance Plugs for Heater Cord Sets
Surface Raceway Systems
Nonmetallic Surface Raceway Systems
Except for: FT4
Wire Connectors
Thermoplastic-Insulated Wires and Cables
Splitters
Cellular Metal and Cellular Concrete Floor Raceways and
Fittings
Electromagnetic Interference (EMI) Filters
Underfloor Raceways and Fittings
Tubular Support Members and Associated Fittings for
Domestic and Commercial Service Masts
Electrical Metallic Tubing
Electrical Metallic Tubing - Steel
Rigid PVC Boxes and Fittings
Portable Power Cables
Except for: FT4
Mine Power Feeder Cables
Except for: FT4
Insulated Multi-pole Splicing Connectors
Appliance Couplers For Household And Similar General
Purposes-Part 1: General Requirements.
Attachment Plug Blades for Use in Cord Sets and
Power-Supply Cords
Electric Space Heating Cables
Pin and Sleeve Configurations
Impregnated-Fiber Electrical Conduit
Radio, Television and Electronic Apparatus
CAN/CSA E384-1
CAN/CSA E384-14
CAN/CSA E60335-2-26
CAN/CSA-E60335-2-56
CAN/CSA-E60384-1
CAN/CSA-E60384-14
CAN/CSA-E61965
SCOPE OF ACCREDITATION
Fixed Capacitors for Use in Electronic Equipment Part 1
Generic Specification
Fixed Capacitors for Use in Electronic Equipment Part 14:
Sectional Specification: Fixed Capacitors for Electromagnetic
Interference Suppression and Connection to the Supply Mains
Safety of Household and Similar Electrical Appliances- Part 2:
Particular Requirements for Clocks
Safety of Household and Similar Electrical Appliances - Part 2:
Particular Requirements for Projectors and Similar Appliances
Fixed Capacitors for Use in Electronic Equipment Part 1:
Generic Specification
Fixed Capacitors for Use in Electronic Equipment Part 14:
Sectional Specification: Fixed Capacitors for Electromagnetic
Interference Suppression and Connection to the Supply Mains
Mechanical Safety of Cathode Ray Tubes
12
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 0.8
CSA C22.2 60065
CSA C22.2 No 118
CSA C22.2 No. 6
CSA C22.2 No. 98
UL 1439
UL 1492
UL 1667
UL 1678
UL 1998
UL 60065
UL 991
Safety Functions Incorporating Electronic Technology
Audio, Video and Similar Electronic Apparatus - Safety
Requirements
Construction and Test of Picture Machines and Appliances
Electric Clocks
Construction and Test of Power-Operated Radio Transmitters
Determination of Sharpness of Edges on Equipment
Audio and Video Equipment
Tall Institutional Carts for Use With Audio-, Video-, and
Television-Type Equipment
Household, Commercial and Professional Use - Carts and
Stands
Software in Programmable Components
Audio, Video and Similar Electronic Apparatus - Safety
Requirements
Tests for Safety-Related Controls Employing Solid-State
Devices
(Electronics Energy Efficiency)
CAN/CSA C380
CAN/CSA C381.1
CAN/CSA C381.2
CAN/CSA C382
CAN/CSA C62301
Test Procedure for the Measurement of Energy Consumption of
Set-Top Boxes (STBs)
Test Method for Calculating the Energy Efficiency of
Single-Voltage External AC-DC and AC-AC Power Supplies
Test Method for Determining the Energy Efficiency of
Battery-Charging Systems
Energy Performance of Televisions and Displays
Household Electrical Appliances-Measurement of Standby
Power
CCR Title 20 California Code of
Regulations, Title 20, Division 2 Televisions and Consumer Audio and Video Equipment
CEC-400-2010-012 section
(on-mode power and luminance)
1604(v)(3)
IEC 62087, Ed. 2:2008
Methods of Measurement for the Power Consumption of
Audio, Video, and Related Equipment
Only for: Clauses 5, 11 for Televisions
IEC 62087:2002
Methods of Measurement for the Power Consumption of
Audio, Video, and Related Equipment.
US-EPA August 11, 2004
Only for: 5, 7, 9 for A/V Equipment
Method for Calculating the Energy Efficiency of
Single-Voltage External AC-DC and AC-AC Power Supplies
Components and Assemblies:
Circuit Breakers and Fuses
SCOPE OF ACCREDITATION
13
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 106
CSA C22.2 115
CSA C22.2 144
CSA C22.2 229
CSA C22.2 235
CSA C22.2 248.1
CSA C22.2 248.10
CSA C22.2 248.11
CSA C22.2 248.12
CSA C22.2 248.13
CSA C22.2 248.14
CSA C22.2 248.15
CSA C22.2 248.2
CSA C22.2 248.3
CSA C22.2 248.4
CSA C22.2 248.5
CSA C22.2 248.6
SCOPE OF ACCREDITATION
HRC Fuses High-Interrupting-Capacity Fuses,
Current-Limiting Types
Except for: Short Circuit Over 10 KA
Meter Mounting Devices
Except for: Devices Rated Over 200A
Ground Fault Circuit Interrupters
Except for: devices rated over 30 A and for Clause 7.1,
Corrosion Test
Switching and Metering Centres
Except for: Devices over 10KA
Supplementary Protectors
Except for: DC Rated Devices
Low-Voltage Fuses Part 1: General Requirements
Except for: Devices rated over 600A and short circuit over 10
KA Low-Voltage Fuses Part 2: Class C Fuses
Low-Voltage Fuses Part 10: Class L Fuses
Except for: Devices rated over 600A and Short Circuit over 10
KA
Low-Voltage Fuses Part 11: Plug Fuses
Except for: Devices rated over 600A and short circuit over 10
KA
Low-Voltage Fuses Part 12: Class R Fuses
Except for: Devices rated over 600A and Short Circuit over 10
KA.
Low-Voltage Fuses Part 13: Semiconductor Fuses
Except for: Devices rated over 600A and short circuit over 10
KA
Low-Voltage Fuses Part 14: Supplemental Fuses
Except for: Devices rated over 600A and Short Circuit over 10
KA.
Low-Voltage Fuses Part 15: Class T Fuses
Except for: Devices rated over 600A and Short Circuit over 10
KA. Clause 8.4, Verification of Operation at Rated Voltage
Low-Voltage Fuses Part 2: Class C Fuses
Except for: Devices rated over 600A and short circuit over 10
KA
Low-Voltage Fuses Part 3: Class CA & CB Fuses
Except for: Devices rated over 600A and short circuit over 10
KA
Low-Voltage Fuses Part 4: Class CC Fuses
Except for: Devices rated over 600A and short circuit over 10
KA
Low-Voltage Fuses Part 5: Class G Fuses
Except for: Devices rated over 600A and short circuit over 10
KA
Low-Voltage Fuses Part 6: Class H - Non-renewable
Except for: Devices rated over 600A and short circuit over 10
14
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 248.7
CSA C22.2 248.8
CSA C22.2 248.9
CSA C22.2 39
CSA C22.2 5
CSA E257
KA
Low-Voltage Fuses Part 7: Class H - Renewable
Except for: Devices rated over 600A and short circuit over 10
KA
Low-Voltage Fuses Part 8: Class J Fuses
Except for: Devices rated over 600A and Short Circuit over 10
KA.
Low-Voltage Fuses Part 9: Class K Fuses
Except for: Devices rated over 600A and short circuit over 10
KA
Fuseholder Assemblies
Moulded Case Switches and Circuit Breaker Enclosures - First
Edition UL489
Fuse-holders for Miniature Cartridge Fuse-Links
Switches and Controls
CAN/CSA E60730-1
CAN/CSA-E60691
CAN/CSA-E60730-2-8
CAN/CSA-E60730-2-9
CSA C22.2 111
CSA C22.2 14
CSA C22.2 156
CSA C22.2 178
CSA C22.2 201
CSA C22.2 76
CSA C22.2 No. 61058-1
EN 60730-2-5
EN 60947-4-1
Automatic Electrical Controls for Household and Similar Use
Part 1: General Requirements
Thermal-Links-Requirements and Application Guide
Automatic Electrical Controls for Household and Similar
Use-Part 2-8: Particular Requirements for Electrically Operated
Water Valves, Including Mechanical Requirements
Automatic Electrical Controls for Household and Similar
Use-Part 2-9: Particular Requirements for Temperature Sensing
Controls
General Use Switches
Industrial Control Equipment
Limitations:
Temperature Test at 10,000Amp Max
Contact Interrupting Test 1,200 Amp Max
Short Circuit Test 10,000Amp Max
Solid-State Speed Controls
Automatic Transfer Switches
Except for: Devices over 1,000Amp(total)
Metal-Enclosed High Voltage Busways
Except for: Clauses 6.2.2 Impulse and 6.2.3 Corona Extinction
Splitters
Switches for Appliances-Part 1: General Requirements
Automatic Electrical Controls for Household and Similar Use
Low-Voltage Switchgear and Controlgear-Part 4: Contactors
and Motor-Starters - Section 1: Electromechanical Contactors
and Motor Starters
Transformers
(Transformers/Power Supplier/Rectifiers)
SCOPE OF ACCREDITATION
15
Standards Council of Canada Accredited Laboratory No. 12
ANSI/UL 5085-1
ANSI/UL 5085-2
ANSI/UL 5085-3
CAN/CSA C22.2 No. 223
CAN/CSA-E61558-1
CAN/CSA-E61558-2-1
CAN/CSA-E61558-2-13
CAN/CSA-E61558-2-2
CAN/CSA-E61558-2-4
CAN/CSA-E61558-2-5
CAN/CSA-E61558-2-6
CSA C22.2 107.3
CSA C22.2 13
CSA C22.2 No. 66.1
CSA C22.2 No. 66.2
CSA C22.2 No. 66.3
CSA C22.2 No.173
CSA C22.2 No.180
CSA C802.1
CSA E742
EN 60742
UL 1778
UL 458
SCOPE OF ACCREDITATION
Low Voltage Transformers - Part 1: General Requirements
Low Voltage Transformers - Part 2: General Purpose
Transformers
Low Voltage Transformers - Part 3: Class 2 and Class 3
Transformers
Power Supplies with Extra-Low-Voltage Class 2 Outputs
Safety of Power Transformers, Power Supply Units and Similar
- Part 1: General Requirements and Tests
Safety of Power Transformers, Power Supply Units and Similar
- Part 2: Particular Requirements for Separating Transformers
for General Use
Safety of Power Transformers, Power Supply Units and Similar
Devices - Part 2-13: Particular Requirements for
Auto-Transformers for General Use
Safety of Power Transformers, Power Supply Units and Similar
- Part 2-2: Particular Requirements for Control Transformers
Safety of Power Transformers, Power Supply Units and Similar
- Part 2: Particular Requirements for Isolating Transformers for
General Use
Safety of Power Transformers, Power Supply Units and Similar
- Part 2-5: Particular Requirements for Shaver Transformers
and Shaver Supply Units
Safety of Power Transformers, Power Supply Units and Similar
- Part 2: Particular Requirements for Safety Isolating
Transformers for General Use
Uninterruptible Power Systems
Transformers for Luminous-Tube Signs, Oil- or Gas-Burner
Ignition Equipment, Cold-Cathode Interior Lighting
Low Voltage Transformers - Part 1: General Requirements
Low Voltage Transformers-Part 2: General Purpose
Transformers
Low Voltage Transformers - Part 3: Class 2 and Class 3
Transformers
Transformers for Toy and Hobby Use
Series Isolating Transformers for Airport Lighting
Minimum Efficiency Values for Liquid-Filled Distribution
Transformers
Isolating Transformers and Safety Isolating Transformers Requirements
Except for: Over 10KVA
Isolating Transformers and Safety Isolating Transformers –
Requirements
Except for: Over 10KVA.
Uninterruptible Power Supplies
Converters and Power Converter Systems for Recreational
Vehicles
16
Standards Council of Canada Accredited Laboratory No. 12
Electrical Appliances:
(Appliances Energy Efficiency)
CSA C191.0
CSA C191.1
CSA C300
CSA C309
CSA C358
CSA C360
CSA C361
CSA C373
CSA C749
CSA Standards on Performance of Electric Storage Tank Water
Heaters
Performance Options for Electric Storage Tank Water Heaters
Capacity Measurement and Energy Consumption Test Methods
for Refrigerators, Combination Refrigerator-Freezers, and
Freezers
Performance Requirements for Glass-Lined Storage Tanks for
Household Hot Water Service
Energy Consumption Test Methods for Household Electric
Ranges
Test Method for Measuring Energy Consumption and Capacity
of Automatic Household Clothes Washers
Test Method for Measuring Energy Consumption and Drum
Volume of Electrically Heated Household Tumble-Type
Clothes Dryers
Energy Consumption Test Methods for Household
Dishwashers
Performance of Dehumidifiers
Cooking and Liquid Heating
CAN/CSA E335-2-65
CSA B45 Series Supplement No.
1
CSA C22.2 101
CSA C22.2 104
CSA C22.2 109
CSA C22.2 110
CSA C22.2 113
CSA C22.2 117
CSA C22.2 120
CSA C22.2 122
CSA C22.2 128
CSA C22.2 140.2
CSA C22.2 140.3
CSA C22.2 15
CSA C22.2 150
CSA C22.2 155
SCOPE OF ACCREDITATION
Safety of Household and Similar Electrical Appliances Part 2:
Particular Requirements for Air Cleaning Appliances
Hydromassage Bathtubs
Electrically Heated Bedding Appliances for Household Use
Humidifiers and Evaporative Coolers
Commercial Cooking Appliances
Construction and Test of Electric Storage Tank Water Heaters
Fans and Ventilators
Room Air Conditioners
Refrigeration Equipment
Hand-Held Electrically Heated Tools
Vending Machines
Hermetic Refrigerant Motor-Compressors
Refrigerant-Containing Components for Use in Electrical
Equipment
Electrically Heated Warming Pads
Microwave Ovens
Electric Duct Heaters
17
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 164
CSA C22.2 165
CSA C22.2 187
CSA C22.2 195
CSA C22.2 218.1
CSA C22.2 218.2
CSA C22.2 224
CSA C22.2 23.1
CSA C22.2 236
CSA C22.2 24
CSA C22.2 3
CSA C22.2 46
CSA C22.2 61
CSA C22.2 63
CSA C22.2 64
CSA C22.2 72
CSA C22.2 88
CSA C22.2 92
CSA E335-1 Edition 2
CSA E335-1 Edition 3
CSA E335-2-12
CSA E335-2-13
CSA E335-2-24
CSA E335-2-30
CSA E335-2-31
CSA E335-2-33
CSA E335-2-34
CSA E335-2-36
CSA E335-2-40
CSA E335-2-41
CSA E335-2-45
CSA E335-2-51
CSA E335-2-57
SCOPE OF ACCREDITATION
Electric Sauna Heaters
Electric Boilers
Electrostatic Air Cleaners
Motor Operated Food Processing Appliances (Household and
Commercial)
Spas, Hot Tubs, and Associated Equipment
Hydromassage Bathtub Appliances
Radiant Heaters and Infrared and Ultraviolet Lamp Assemblies
for Cosmetic or Hygienic Purposes in Nonmedical
Applications
Electric Furnaces in Combination with Solid Fuel Fired
Furnaces
Except for: Solid Fuel Portion
Heating and Cooling Equipment, 600V maximum
Temperature-Indicating and Regulating Equipment
Electrical Features of Fuel-Burning Equipment
Electric Air-Heaters
Household Cooking Ranges
Household Refrigerators and Freezers
Household Cooking and Liquid-Heating Appliances
Heater Elements
Construction and Test of Industrial Heating Equipment
Dehumidifiers
Safety of Household and Similar Electrical Appliances Part 1:
General Requirements
Safety of Household and Similar Electrical Appliances Part 1:
General Requirements
Part 2: Warming Plates and Similar Appliances
Part 2: Frying Pans, Deep Fat Fryers, and Similar Appliances
Part 2: Refrigerators, Food-Freezers and Ice-Makers
Part 2: Room Heaters
Part 2: Range Hoods
Part 2: Coffee Mills and Coffee Grinders
Part 2: Motor-Compressors
Part 2: Commercial Electric Cooking Ranges, Ovens and Hob
Elements
Part 2: Electrical Heat Pumps, Air-Conditioners and
Dehumidifiers
Part 2: Electric Pumps for Liquids Having a Temperature Not
Exceeding 35°C
Part 2: Portable Electric Heating Tools and Similar Appliances
Part 2: Stationary Circulation Pumps for Heating and Service
Water Installations
Part 2: Ice-cream Appliances With Incorporated
Motor-Compressors
18
Standards Council of Canada Accredited Laboratory No. 12
CSA E335-2-63
CSA E335-2-9
CSA E342-1-95
CSA E60335-2-14
CSA E60335-2-64
UL 1563
UL 1995
UL 858A
Part 2: Commercial Electric Water Boilers and Liquid Heaters
Part 2: Toasters, Grills, Roasters and Similar Appliances
Fans and Regulators for Household and Similar Purposes
Part 2: Electric Kitchen Machines
Part 2: Commercial Electric Kitchen Machines
Electric Spas, Equipment Assemblies, and Associated
Equipment
Heating and Cooling Equipment, 600 V maximum
Safety-Related Solid-State Controls for Household Electric
Ranges
Lighting and Fixtures
CSA C22.2 12
CSA C22.2 141
CSA C22.2 166
CSA C22.2 184
CSA C22.2 184.1
CSA C22.2 207
CSA C22.2 250
Portable Luminaires
Unit Equipment for Emergency Lighting
Stage and Studio Luminaires
Solid-State Lighting Controls
Solid-State Dimming Controls
Portable and Stationary Electric Signs and Displays
Luminaires
Except for: Clause 9.2.3.2 “large scale fallout” and Clause
9.2.3.3 “impingement fire”.
CSA C22.2 37
CSA C22.2 74
CSA C22.2 89
Christmas Tree and Other Decorative Lighting Outfits
Equipment for Use with Electric Discharge Lamps
Swimming-Pool Luminaires, Submersible Luminaires and
Accessories
General Requirements for Luminaires
Performance of Internally Lighted Exit Signs
Flexible Lighting Products
CSA C22.2 9.0
CSA C860
UL2388
Miscellaneous Electrical Appliances (Specify)
CAN/CSA E335-2-59
CAN/CSA E60335-2-59
CSA C22.2 0.15
CSA C22.2 102
CSA C22.2 103
CSA C22.2 189
CSA C22.2 191
CSA C22.2 200
CSA C22.2 221
SCOPE OF ACCREDITATION
Safety of Household and Similar Electrical Appliances Part 2:
Particular Requirements for Insect Killers
Household and Similar Electrical Appliances-Safety- Part 2-59:
Particular Requirements for Insect Killers
Adhesive Labels
Brooders and Incubators
Electric Fence Controllers
High-Voltage Insect Killers
Engine Heaters and Battery Warmers
Electric Waterbed Heater Systems
Electrically Heated Hobby and Educational Type Kilns
19
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 224
CSA C22.2 36
CSA C22.2 81
CSA C22.2 99
CSA E335-2-18
CSA E335-2-19
CSA E335-2-20
CSA E335-2-23
CSA E335-2-27
CSA E335-2-29
CSA E335-2-44
CSA E335-2-70
CSA E60335-2-8
CSA-E60335-2-76
UL 979
Radiant Heaters and Infrared and Ultraviolet Lamp Assemblies
for Cosmetic or Hygienic Purposes in Nonmedical
Applications
Hairdressing Equipment
Electric Irons
Construction and Test of Domestic Electric Ironing Machines
Part 2: Guide for Preparing Safety Requirements for
Battery-Powered Motor-Operated Appliances and Their
Charging and Battery Assemblies
Part 2: Battery-Powered Shavers, Hair Clippers and Similar
Appliances and Their Charging and Battery Assemblies
Part 2: Battery-Powered Toothbrushes and Their Charging and
Battery Assemblies
Part 2: Appliances for Skin or Hair Care
Part 2: Ultra-Violet and Infra-Red Radiation Skin Treatment
Appliances for Household Use
Part 2: Battery Chargers
Part 2: Electric Ironers
Part 2: Milking Machines
Part 2: Electric Shavers, Hair Clippers and Similar Appliances
Safety of Household and Similar Electrical Appliances - Part 2:
Particular Requirements for Electric Fence Energizers
Water Treatment Appliances
Motor Operated Electrical Appliances
C22.2 No 68
C22.2 No. 60745-2-2
C22.2 No. 60745-2-3
CSA C22.2 10
CSA C22.2 105
CSA C22.2 112
CSA C22.2 147
CSA C22.2 243
CSA C22.2 247
CSA C22.2 71.2
CSA C22.2 73
CSA C22.2 No. 60745-1
CSA C22.2 No. 60745-2-1
CSA C22.2 No. 60745-2-11
CSA C22.2 No. 60745-2-12
CSA C22.2 No. 60745-2-14
SCOPE OF ACCREDITATION
Motor-Operated Appliances (Household and Commercial)
Hand-held Motor-Operated Electric Tools-Screwdrivers and
Impact Wrenches
Hand-held Motor-Operated Electric Tools- Grinders, Polishers
and Disk-Type Sanders
Electric Floor Surfacing and Cleaning Machines
Electrical Equipment for Woodworking Machinery
Clothes Drying Machines
Motor-Operated Gardening Appliances
Vacuum Cleaners and Blower Cleaners
Garage Door Operators and Systems
Electric Bench Tools
Construction and Test of Electrically-Equipped Machine Tools
Hand-held Motor-Operated Electric Tools
Hand-held Motor-Operated Electric Tools- Drills and Impact
Drills
Hand-held Motor-Operated Electric Tools- Reciprocating Saws
Hand-held Motor-Operated Electric Tools- Concrete Vibrators
Hand-held Motor-Operated Electric Tools- Planers
20
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 No. 60745-2-15
CSA C22.2 No. 60745-2-16
CSA C22.2 No. 60745-2-17
CSA C22.2 No. 60745-2-18
CSA C22.2 No. 60745-2-19
CSA C22.2 No. 60745-2-20
CSA C22.2 No. 60745-2-21
CSA C22.2 No. 60745-2-4
CSA C22.2 No. 60745-2-5
CSA C22.2 No. 60745-2-6
CSA C22.2 No. 60745-2-8
CSA C22.2 No. 60745-2-9
CSA E1029-1
CSA E1029-2-1
CSA E1029-2-2
CSA E1029-2-3
CSA E1029-2-4
CSA E1029-2-5
CSA E1029-2-6
CSA E1029-2-7
CSA E335 2 56
CSA E335-2-11
CSA E335-2-26
CSA E335-2-4
CSA E335-2-55
CSA E60335-2-10
CSA E60335-2-16
CSA E60335-2-2
CSA E60335-2-28
CSA E60335-2-32
CSA E60335-2-52
CSA E60335-2-54
CSA E60335-2-67
CSA E60335-2-68
Hand-held Motor-Operated Electric Tools- Hedge Trimmers
Hand-held Motor-Operated Electric Tools- Tackers
Hand-held Motor-Operated Electric Tools- Routers and
Trimmers
Hand-held Motor-Operated Electric Tools- Strapping Tools
Hand-held Motor-Operated Electric Tools- Jointers
Hand-held Motor-Operated Electric Tools- Band Saws
Hand-held Motor-Operated Electric Tools- Drain Cleaners
Hand-held Motor-Operated Electric Tools- Sanders and
Polishers Other Than Disk Type
Hand-held Motor-Operated Electric Tools- Circular Saws
Hand-held Motor-Operated Electric Tools- Hammers
Hand-held Motor-Operated Electric Tools- Shears and Nibblers
Hand-held Motor-Operated Electric Tools- Tappers
Transportable Motor-Operated Electric Tools (Portable Power
Tools) Part 1: General Requirements
Part 2: Circular Saws
Part 2: Radial Arm Saws
Part 2: Planers and Thicknessers
Part 2: Bench Grinders
Part 2: Band Saws
Part 2: Diamond Drills With Water Supply
Part 2: Diamond Saws With Water Supply
Part 2: Particular Requirements for Projectors and Similar
Appliances
Part 2: Tumbler Dryers
Part 2: Clocks
Part 2: Spin Extractors
Part 2: Electrical Appliances for Use With Aquariums and
Garden Ponds
Part 2: Floor Treatment Machines and Wet Scrubbing
Machines
Part 2: Food Waste Disposers
Part 2: Vacuum Cleaners and Water Suction Cleaning
Appliances
Part 2: Sewing Machines
Part 2: Massage Appliances
Part 2: Oral Hygiene Appliances Connected to the Mains
Supply Through a Safety Isolating Transformer
Part 2: General Purpose Cleaning Appliances
Part 2: Floor Treatment and Floor Cleaning Machines, for
Industrial and Commercial Use
Part 2: Spray Extraction Appliances For Industrial and
Commercial Use
CSA E60335-2-69
SCOPE OF ACCREDITATION
21
Standards Council of Canada Accredited Laboratory No. 12
CSA E60335-2-82
NFPA 79
UL 1450
UL 1556
UL 1624
UL 560
Part 2: Wet and Dry Vacuum Cleaners, Including Power Brush,
for Industrial and Commercial Use
Part 2-82: Particular Requirements for Amusement Machines
and Personal Service Machines
Electrical Standard for Industrial Machinery
Motor-Operated Air Compressors, Vacuum Pumps, and
Painting Equipment
Electric Coin-Operated Clothes-Drying Equipment
Light Industrial Tools
Electric Home-Laundry Equipment
Washing Equipment
CSA C22.2 167
CSA C22.2 168
CSA C22.2 169
CSA C22.2 53
UL 1555
UL 560
Household Dishwashing Machines
Commercial Dishwashing Machines
Clothes Washing Machines
Electric Washing Machines
Electric Coin-Operated Clothes-Washing Equipment
Electric Home-Laundry Equipment
Equipment, Miscellaneous
CSA C22.2 0
CSA C22.2 160
General Requirements - Canadian Electrical Code, Part II
Voltage and Polarity Testers
(Enclosed Equipment)
CSA E61241-1-1
NFPA 496
Electrical Apparatus for Use in the Presence of Combustible
Dust - Part 1: Electrical Apparatus Protected by Enclosures
Purged and Pressurized Enclosures for Electrical Equipment
Conductors
CSA C22.2 0.12
CSA C22.2 27
Wiring Space and Wire Bending Space in Enclosures for
Equipment Rated 750 V or Less
Busways
Enclosures
CSA C22.2 94
IEC 60529
UL 887
Special Purpose Enclosures
Except for: Sleet and Ice Formation Test
Degrees of Protection Provided by Enclosures (IP Code)
Delayed-Action Timelocks
Hazardous Location Equipment
SCOPE OF ACCREDITATION
22
Standards Council of Canada Accredited Laboratory No. 12
ANSI/ISA 12.12.01
ANSI/ISA 12.13.01
ANSI/ISA 12.27.01
ANSI/ISA 60079-0
(12.00.01)
ANSI/ISA 60079-1 (12.22.01)
ANSI/ISA 60079-11 (12.02.01)
ANSI/ISA 60079-15 (12.12.02)
ANSI/ISA 60079-18 (12.02.02)
ANSI/ISA 60079-2 (12.04.01)
ANSI/ISA 60079-26 (12.00.03)
ANSI/ISA 60079-27 (12.02.04)
ANSI/ISA 60079-31 (12.10.03)
ANSI/ISA 60079-5 (12.25.01)
ANSI/ISA 60079-6 (12.26.01)
ANSI/ISA 60079-7 (12.16.01)
ANSI/ISA 61241-0 (12.10.02)
ANSI/ISA 61241-1 (12.10.03)
ANSI/ISA-61241-11
(12.10.04)
ANSI/ISA-61241-18 (12.10.07)
SCOPE OF ACCREDITATION
Nonincendive Electrical Equipment for Use in Class I and II,
Division 2 and Class III, Divisions 1 and 2 Hazardous
(Classified) Locations
Performance Requirements for Combustible Gas Detectors
Except for: Clause 3.8 - Vibration Test
Requirements for Process Sealing between Electrical System
and Flammable or Combustible Process Fluids
Explosive Atmospheres - Part 0: Equipment - General
Requirements
Explosive Atmospheres - Part 1: Equipment Protection by
Flameproof Enclosures "d"
Except for: Toronto: All explosion tests other than for sintered
or flame arrester components with free internal volume less
than 5cc
Explosive Atmospheres - Part 11: Equipment Protection by
Intrinsic Safety "i"
Electrical Apparatus for Use in Class I, Zone 2 Hazardous
(Classified) Locations: Type of Protection "n"
Electrical Apparatus for Use in Class I, Zone 1 Hazardous
(Classified) Locations: Type of Protection - Encapsulation "m"
Explosive Atmospheres - Part 2: Equipment Protection by
Pressurized Enclosure "p"
Electrical Apparatus for Use in Class I, Zone 0 Hazardous
(Classified) Locations
Fieldbus Intrinsically Safe Concept (FISCO) and Fieldbus
Non-Incendive Concept (FNICO)
Explosive Atmospheres - Part 31: Equipment Dust Ignition
Protection by Enclosure "t"
Explosive Atmospheres - Part 5: Equipment Protection by
Powder Filling "q"
Explosive Atmospheres - Part 6: Equipment Protection by Oil
Immersion (o)
Explosive Atmospheres - Part 7: Equipment Protection by
Increased Safety "e"
Electrical Apparatus for Use in Zone 20, Zone 21 and Zone 22
Hazardous (Classified) Locations - General Requirements
Electrical Apparatus for Use in Zone 21 and Zone 22
Hazardous (Classified) Locations - Protection by Enclosures
"tD"
Electrical Apparatus for Use in Zone 20, Zone 21 and Zone 22
Hazardous (Classified) Locations - Protection by Intrinsic
Safety "iD"
Electrical Apparatus for Use in Zone 20, Zone 21 and Zone 22
Hazardous (Classified) Locations - Protection by Encapsulation
"mD"
23
Standards Council of Canada Accredited Laboratory No. 12
ANSI/ISA-61241-2 (12.10.06)
CSA C22.2 138
CSA C22.2 142
CSA C22.2 145
CSA C22.2 152
CSA C22.2 157
CSA C22.2 159
CSA C22.2 174
CSA C22.2 213
CSA C22.2 25
CSA C22.2 30
CSA C22.2 60079-0
Electrical Apparatus for Use in Zone 21 and Zone 22
Hazardous (Classified) Locations - Protection by Pressurization
"pD"
Heat Tracing Cable and Cable Sets for Use in Hazardous
Locations
Except for: Clauses 7.4.3 Explosion-Proof Test (Class I,
Division 1 only) and 7.4.4 Overpressure (Class I, Division 1
only)
Process Control Equipment
Motors and Generators for Use in Hazardous Locations
Except for: 7.1 Explosion
7.1.2 Maximum Explosion Pressure,
7.1.3 Explosion Flame Propagation
7. 2 Overpressure Tests Over 2000 psig
7.3 Abnormal Temperature Over 50 HP
10.2 Abnormal Temperature (Blanketing) Over 50 HP
Combustible Gas Detection Instruments
Intrinsically Safe and Non-Incendive Equipment for Use in
Hazardous Locations
Attachment Plugs, Receptacles, and Similar Wiring Devices for
Use in Hazardous Locations: Class I, Groups A, B, C, and D;
Class II, Group G, in Coal or Coke Dust, and in Gaseous Mines
Except for: Clauses 6.15.1 Enclosures - Explosion pressure,
Explosion Flame Propagation and Over Pressure up to 2000
psig
6.15.2.2 Delayed Withdrawal and Plug Receptacle/Connector
6.16.2 Plug Receptacle/Connector - Dust Ignition
6.16.2.2 Delayed Withdrawal and Plug Receptacle/Connector
Cables and Cable Glands for Use in Hazardous Locations
Except for: Clauses
4.3.2 Flame Test
4.3.4 Explosion (Cables with bundled sub-assemblies)
5.8.7 Explosion Class I - Cable Glands with Integral Seals Only
Non-Incendive Electrical Equipment for Use in Class I,
Division 2 Hazardous Locations
Enclosures for Use in Class II, Groups E, F and G Hazardous
Locations
Except for: Clause 5.2 Dust-tightness
Explosion-Proof Enclosures for Use in Class I Hazardous
Locations
Except for: Toronto: Clauses 6.3 Explosion Pressure Test, 6.4
Arc-Rupturing, 6.5 Explosion Flame Propagation Test
Note: Explosion tests are possible for very small components
like sintered or flame arrester components with free internal
volume less than 5cc
Electrical Apparatus for Explosive Gas Atmospheres - Part 0:
General Requirements
CSA C22.2 60079-11
SCOPE OF ACCREDITATION
24
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 60079-15
CSA C22.2 60079-18
CSA C22.2 60079-2
CSA C22.2 60079-31
CSA C22.2 60079-5
CSA C22.2 60079-6
CSA C22.2 60079-7
CSA C22.2 61241-4
CSA C22.2 60079-1
EN 60079-0
EN 60079-1
EN 60079-11
EN 60079-14
EN 60079-15
Electrical Apparatus for Explosive Gas Atmospheres - Part 11:
Intrinsic Safety "i"
Electrical Apparatus for Explosive Gas Atmospheres - Part 15:
Type of Protection "n"
Except for: Clauses 26.10 - Test for Screw Lampholders and
26.11 - Test for Starter Holders for Luminaires
Electrical Apparatus for Explosive Gas Atmospheres - Part 18:
Encapsulation "m"
Electrical Apparatus for Explosive Gas Atmospheres‑Part 2:
Pressurized Enclosures "p"
Explosive Atmospheres - Part 31: Equipment Dust Ignition
Protection by Enclosure "t"
Electrical Apparatus for Explosive Gas Atmospheres - Part 5:
Powder Filling "q"
Electrical Apparatus for Explosive Gas Atmospheres - Part 6:
Oil-Immersion "o"
Electrical Apparatus for Explosive Gas Atmospheres - Part 7:
Increased Safety "e"
Except for: Cl 6.2 Annex B Rotor Temperature Measurement
Electrical Apparatus for Use in the Presence of Combustible
Dust - Part 4: Type of Protection "PD"
Electrical Apparatus for Explosive Gas Atmospheres - Part 1:
Flameproof Enclosures "d"
Except for: Toronto: Clauses:
15.1.2 Determination of Explosion Pressure (Reference
Pressure)
15.2 Test for Non-transmission of an Internal Ignition
15.4.2 Tests of Flameproof Enclosures with Breathing and
Draining Devices
19.3.1.3 Test of Errosion of Flame
Note: Explosion tests are possible for very small components
like sintered or flame arrester components with free internal
volume less than 5cc
Explosive Atmospheres - Part 0: Equipment - General
Requirements
Explosive Atmospheres - Part 1: Equipment Protection by
Flameproof Enclosures "d"
Except for: All explosion tests other than for sintered or flame
arrester components with free internal volume less than 5cc
Explosive Atmospheres - Part 11: Equipment Protection by
Intrinsic Safety "i"
Explosive Atmospheres - Part 14: Electrical Installations
Design, Selection and Erection
Explosive Atmospheres - Part 15: Equipment Protection by
Type of Protection "n"
EN 60079-18
SCOPE OF ACCREDITATION
25
Standards Council of Canada Accredited Laboratory No. 12
EN 60079-2
EN 60079-25
EN 60079-26
EN 60079-27
EN 60079-29-1
EN 60079-30-1
EN 60079-31
EN 60079-5
EN 60079-6
EN 60079-7
FM 3610
FM 3611
FM 3615
FM 3616
FM 3620
FM 3810
FM 6310, 6320
FM-3600
IEC 60079-0
IEC 60079-1
SCOPE OF ACCREDITATION
Explosive Atmospheres - Part 18: Equipment Protection by
Encapsulation "m"
Explosive Atmospheres - Part 2: Equipment Protection by
Pressurized Enclosure "p"
Explosive Atmospheres - Part 25: Intrinsically Safe Electrical
Systems
Explosive Atmospheres - Part 26: Equipment with Equipment
Protection Level (EPL) Ga
Explosive Atmospheres - Part 27: Fieldbus Intrinsically Safe
Concept (FISCO)
Explosive Atmospheres - Part 29-1: Gas Detectors Performance Requirements of Detectors for Flammable Gases
Explosive Atmospheres - Part 30-1: Electrical Resistance Trace
Heating - General and Testing Requirements
Explosive Atmospheres - Part 31: Equipment Dust Ignition
Protection by Enclosure "t"
Explosive Atmospheres - Part 5: Equipment Protection by
Powder Filling «q»
Explosive Atmospheres - Part 6: Equipment Protection by Oil
immersion (o)
Explosive Atmospheres - Part 7: Equipment Protection by
Increased Safety "e"
Intrinsically Safe Apparatus for Use in Class I, II & III,
Division 1, and Class I, Zone 0 & 1 Hazardous (Classified)
Locations
Nonincendive Electrical Equipment for Use in Class I and
Class II, Division 2, and Class III, Division 1 and 2 Hazardous
(Classified) Locations
Explosionproof Electrical Equipment, General Requirements
Except for: Toronto: All explosion tests other than for sintered
or flame arrester components with free internal volume less
than 5cc
Dust-Ignitionproof Electrical Equipment, General
Requirements
Purged and Pressurized Electrical Equipment for Hazardous
(Classified) Locations
Electrical and Electronic Test, Measuring, and Process Control
Equipment
Combustible Gas Detectors
Electrical Equipment for Use in Hazardous (Classified)
Locations, General Requirements
Explosive Atmospheres - Part 0: Equipment - General
Requirements
Explosive Atmospheres - Part 1: Equipment Protection by
Flameproof Enclosures "d"
26
Standards Council of Canada Accredited Laboratory No. 12
IEC 60079-11
IEC 60079-14
IEC 60079-15
IEC 60079-18
IEC 60079-2
IEC 60079-25
IEC 60079-26
IEC 60079-29
IEC 60079-30-1
IEC 60079-31
IEC 60079-5
IEC 60079-6
IEC 60079-7
UL 1203
UL 60079-0
UL 60079-1
UL 60079-11
UL 60079-15
UL 60079-18
SCOPE OF ACCREDITATION
Except for: Toronto: All explosion tests other than for sintered
or flame arrester components with free internal volume less
than 5cc
Explosive Atmospheres - Part 11: Equipment Protection by
Intrinsic Safety "i"
Explosive Atmospheres - Part 14: Electrical Installations
Design, Selection and Erection
Explosive Atmospheres - Part 15: Equipment Protection by
Type of Protection "n"
Explosive Atmospheres - Part 18: Equipment Protection by
Encapsulation "m"
Explosive Atmospheres - Part 2: Equipment Protection by
Pressurized Enclosure "p"
Explosive Atmospheres - Part 25: Intrinsically Safe Electrical
Systems
Explosive Atmospheres - Part 26: Equipment with Equipment
Protection Level (EPL) Ga
Explosive Atmospheres - Part 29-1: Gas Detectors Performance Requirements of Detectors for Flammable Gases
Explosive Atmospheres - Part 30-1: Electrical Resistance Trace
Heating - General and Testing Requirements
Explosive Atmospheres - Part 31: Equipment Dust Ignition
Protection by Enclosure "t"
Explosive Atmospheres - Part 5: Equipment Protection by
Powder Filling «q»
Explosive Atmospheres - Part 6: Equipment Protection by Oil
Immersion (o)
Explosive Atmospheres - Part 7: Equipment Protection by
Increased Safety "e"
Explosion-Proof and Dust-Ignition-Proof Electrical Equipment
for Use in Hazardous (Classified) Locations
Except for: All explosion tests other than for sintered or flame
arrester components with free internal volume less than 5cc
UL Standard for Safety Explosive Atmospheres - Part 0:
Equipment - General Requirements
UL Standard for Safety Explosive Atmospheres - Part 1:
Equipment Protection by Flameproof Enclosures "d"
Except for: All explosion tests other than for sintered or flame
arrester components with free internal volume less than 5cc
UL Standard for Safety Explosive Atmospheres - Part 11:
Equipment Protection by Intrinsic Safety "i"
UL Standard for Safety Electrical Apparatus for Explosive Gas
Atmospheres - Part 15: Construction, Test and Marking of
Type of Protection "n" Electrical Apparatus
UL Standard for Safety Electrical Apparatus for Explosive Gas
Atmospheres - Part 18: Construction, Test and Marking of
27
Standards Council of Canada Accredited Laboratory No. 12
UL 60079-5
UL 60079-6
UL 60079-7
UL 674
UL 844
UL 886
UL 913
Type of Protection Encapsulation "m" Electrical Apparatus
UL Standard for Safety Explosive Atmospheres - Part 5:
Equipment Protection by Powder Filling "q"
UL Standard for Safety Explosive Atmospheres - Part 6:
Equipment Protection by Oil Immersion "o"
UL Standard for Safety Explosive Atmospheres - Part 7:
Equipment Protection by Increased Safety "e"
Electric Motors and Generators for Use in Hazardous
(Classified) Locations
Electric Lighting Fixtures for Use in Hazardous (Classified)
Locations
Electrical Outlet Boxes and Fittings for Use in Hazardous
(Classified) Locations
Intrinsically Safe Apparatus and Associated Apparatus for Use
in Class I, II and III, Division 1, Hazardous Locations
Panels
CSA C22.2 29
Panelboards and Enclosed Panelboards
Except for: Short Circuit over 10 KA
Welding
CSA C22.2 60
Arc Welding Equipment
Except for: Engine driven welder test
Information Processing and Business Equipment:
(Generally Applicable Tests)
ANSI/UL 60950
ANSI/UL 60950-1
ANSI/UL 60950-21
ANSI/UL 60950-22
ANSI/UL 60950-23
AS/NZ 60950 (2000)
AS/NZS 3260 (1993) +
Supplement 1 (1996)
AS/NZS 4117 (1999)
AS/NZS 60950.1 (2003)
CAN/CSA 60950
SCOPE OF ACCREDITATION
Safety of Information Technology Equipment
Information Technology Equipment Safety Part 1: General
Requirements
Information Technology Equipment-Safety-Part 21: Remote
Power Feeding
Information Technology Equipment - Safety - Part 22:
Equipment to be Installed Outdoors
Information Technology Equipment - Safety - Part 23: Large
Data Storage Equipment
Safety of Information Technology Equipment
Safety of Information Technology Equipment including
Electrical Business Equipment
Surge Protective Devices for Telecommunications Applications
Information Technology Equipment - Safety - Part 1: General
Requirements (IEC 60950-1:2001, MOD)
Safety of Information Technology Equipment
28
Standards Council of Canada Accredited Laboratory No. 12
CAN/CSA 60950-1
CAN/CSA C22.2 No 60950-21
CAN/CSA C22.2 No 60950-22
CAN/CSA C22.2 No 60950-23
Information Technology Equipment Safety Part 1: General
Requirements - Second Edition
Information Technology Equipment-Safety-Part 21: Remote
Power Feeding
Information Technology Equipment - Safety - Part 22:
Equipment to be Installed Outdoors
Information Technology Equipment - Safety - Part 23: Large
Data Storage Equipment
Photocopying and Related Equipment
CSA E335-2-56
CSA E491
Part 2: Projectors and Similar Appliances
Safety Requirements for Electronic Flash Apparatus for
Photographic Purposes
Materials:
Plastics
CSA C22.2 0.17
CSA C22.2 197
Evaluation of Properties of Polymeric Compounds
Except for: clause 5.2, Charpy Impact
PVC Insulating Tape
Except for: 4.3.4, Radiant Panel
(Labels)
C22.2 No. 0.15
Adhesive Labels
Medical Devices:
Breathing Apparatus and Equipment
(First Aid - Medical Gas System)
CSA Z168.5.1
CSA Z305.1
CSA Z305.2
Anesthesia Ventilators
Nonflammable Medical Gas Piping Systems
Low-Pressure Connecting Assemblies for Medical Gas
Systems
Treatment Equipment
AAMI/ANSI/IEC 80601-2-30
SCOPE OF ACCREDITATION
Medical Electrical Equipment-Part 2-30: Particular
Requirements for the Basic Safety and Essential Performance
of Automated Non-Invasive Sphygmomanometers
29
Standards Council of Canada Accredited Laboratory No. 12
ANSI/AAMI
ES60601-1:2005/C1
Medical Electrical Equipment - Part 1: General Requirements
for Basic Safety and Essential Performance - Amendment 1
Except for: Cl.15.4.3.4 - Lithium batteries.
ANSI/AAMI/IEC 60601-1-2
Medical Electrical Equipment - Part 1-2: General Requirements
for Basic Safety and Essential Performance - Collateral
Standard: Electromagnetic Compatibility - Requirements and
Tests
ANSI/AAMI/IEC
Medical Electrical Equipment - Part 1-2: General Requirements
60601-1-2:2001
for Basic Safety and Essential Performance- Collateral
Standard: Electromagnetic Compatibility - Requirements and
Tests (Includes Amendment 1)
ANSI/AAMI/IEC 60601-2-19
Medical Electrical Equipment - Part 2-19: Particular
Requirements for the Basic Safety and Essential Performance
of
Infant Incubators
ANSI/AAMI/IEC 60601-2-20
Medical Electrical Equipment - Part 2-20: Particular
Requirements for the Basic Safety and Essential Performance
of Infant Transport Incubators
ANSI/AAMI/IEC
Medical Electrical Equipment, Part 2-21: Particular
60601-2-21:2001
Requirements for the Safety of Infant Radiant Warmers
(Includes Amendment 1)
ANSI/AAMI/IEC
Medical Electrical Equipment, Part 2-21: Particular
60601-2-21-2009
Requirements for the Basic Safety and Essential; Performance
of Infant Radiant Warmers
Except for: concentration of carbon dioxide
ANSI/AAMI/IEC 60601-2-50
Medical Electrical Equipment, Part 2-50: Particular
Requirements for the Basic Safety and Essential Performance
of Infant Phototherapy Equipment
ANSI/AAMI/IEC
Medical Electrical Equipment, Part 2-50: Particular
60601-2-50:2006
Requirements for the Safety of Infant Phototherapy Equipment
C22.2 No 60601-2-9
Medical Electrical Equipment - Part 2: Particular Requirements
for the Safety of Patient Contact Dosemeters Used in
Radiotherapy with Electrically Connected Radiation Detectors
CAN/CSA C22.2 601.1S1
Supplement No. 1-94 to CAN/CSA-C22.2 No.
601.1-M90-Medical Electrical Equipment, Part 1: General
Requirements for Safety
CAN/CSA C22.2 No 60601-1
Medical Electrical Equipment, Part 1: General Requirements
for Basic Safety and Essential Performance (Adopted IEC
60601-2:2005, Third Edition, 2005-12) which incorporates
Corrigendum 1:2006
CAN/CSA C22.2 No 60601-1-08 Technical Corrigendum 2:2011 to CAN/CSA-C22.2 No.
TC 2:2011 (Corrigendum2)
60601-1-08, Medical Electrical Equipment - Part 1: General
Requirements for Basic Safety and Essential Performance
(Adopted IEC 60601-1:2005, Third Edition, 2005-12
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-29: Particular
20201-2-29
Requirements for the Basic Safety and Essential Performance
of Radiotherapy Simulators
CAN/CSA C22.2 No. 60601-1-1 Medical Electrical Equipment - Part 1-1: General Requirements
SCOPE OF ACCREDITATION
30
Standards Council of Canada Accredited Laboratory No. 12
CAN/CSA C22.2 No.
60601-1-10
CAN/CSA C22.2 No. 60601-1-2
CAN/CSA C22.2 No. 60601-1-4
CAN/CSA C22.2 No. 60601-1-6
CAN/CSA C22.2 No. 60601-1-8
CAN/CSA C22.2 No. 60601-2-1
CAN/CSA C22.2 No.
60601-2-11
CAN/CSA C22.2 No.
60601-2-12
CAN/CSA C22.2 No.
60601-2-13
CAN/CSA C22.2 No.
60601-2-16
CAN/CSA C22.2 No.
60601-2-17
CAN/CSA C22.2 No.
60601-2-18
CAN/CSA C22.2 No.
60601-2-19
CAN/CSA C22.2 No. 60601-2-2
SCOPE OF ACCREDITATION
for Safety - Collateral Standard: Safety Requirements for
Medical Electrical Systems
Medical Electrical Equipment - Part 1-10: General
Requirements for Basic Safety and Essential Performance Collateral Standard: Requirements for the Development of
Physiologic Closed-loop Controllers
Medical Electrical Equipment - Part 1-2: General Requirements
for Basic Safety and Essential Performance - Collateral
Standard: Electromagnetic Compatibility - Requirements and
Tests (Adopted CEI/IEC 60601-1-2:2001 + A1:2004, edition
2.1, 2004-11)
Medical Electrical Equipment - Part 1-4: General Requirements
for Safety - Collateral Standard: Programmable Electrical
Medical Systems (Adopted CEI/IEC
60601-1-4:1996+A1:1999, Edition 1.1, 2000-04)
Medical Electrical Equipment - Part 1-6: General Requirements
for Basic Safety and Essential Performance - Collateral
Standard: Usability
Medical Electrical Equipment - Part 1-8: General Requirements
for Basic Safety and Essential Performance - Collateral
Standard: General Requirements, Tests and Guidance for
Alarm Systems in Medical Electrical Equipment and Medical
Electrical Systems
Except for: Except for: Cl. 15.4.3.4 - Lithium batteries
Medical Electrical Equipment - Part 2-1: Particular
Requirements for the Safety of Electron Accelerators in the
Range 1 MeV to 50 MeV
Medical Electrical Equipment - Part 2: Particular Requirements
for the Safety of Gamma Beam Therapy Equipment
Medical Electrical Equipment - Part 2: Particular Requirements
for the Safety of Lung Ventilators - Critical Care Ventilators
Medical Electrical Equipment Part 2-13: Particular
Requirements for the Safety and Essential Performance of
Anaesthetic Systems
Medical Electrical Equipment - Part 2-16: Particular
Requirements for Basic Safety and Essential Performance of
Haemodialysis, Haemodiafiltration and Haemofiltration
Equipment
Medical Electrical Equipment - Part 2-17: Particular
Requirements for the Safety of Automatically-Controlled
Brachytherapy Afterloading Equipment
Medical Electrical Equipment - Part 2: Particular Requirements
for the Safety of Endoscopic Equipment
Medical Electrical Equipment - Part 2-19: Particular
Requirements for the Basic Safety and Essential Performance
of Infant Incubators
Medical Electrical Equipment - Part 2-2: Particular
Requirements for the Safety of High Frequency Surgical
31
Standards Council of Canada Accredited Laboratory No. 12
Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-20: Particular
60601-2-20
Requirements for the Basic Safety and Essential Performance
of Infant Transport Incubators
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-21: Particular
60601-2-21
Requirements for the Basic Safety and Essential Performance
of Infant Radiant Warmers
Except for: concentration of carbon dioxide.
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-22: Particular
60601-2-22
Requirements for Basic Safety and Essential Performance of
Surgical, Cosmetic, Therapeutic and Diagnostic Laser
Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-23: Particular
60601-2-23
Requirements for the Safety, Including Essential Performance,
of Transcutaneous Partial Pressure Monitoring Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-24: Particular
60601-2-24
Requirements for the Safety of Infusion Pumps and Controllers
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-26: Particular
60601-2-26
Requirements for the Safety of Electroencephalographs
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-27: Particular
60601-2-27
Requirements for the Safety, Including Essential Performance,
of Electrocardiographic Monitoring Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-30: Particular
60601-2-30
Requirements for the Safety, Including Essential Performance,
of Automatic Cycling Non-Invasive Blood Pressure Monitoring
Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-31: Particular
60601-2-31
Requirements for the Basic Safety and Essential Performance
of External Cardiac Pacemakers with Internal Power Source
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-33: Particular
60601-2-33
Requirements for the Safety of Magnetic Resonance
Equipment for Medical Diagnosis
Except for: Cl. 51 - Protection against hazardous output.
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-34: Particular
60601-2-34
Requirements for the Safety, Including Essential Performance,
of Invasive Blood Pressure Monitoring Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-37: Particular
60601-2-37
Requirements for the Basic Safety and Essential Performance
of Ultrasonic Medical Diagnostic and Monitoring Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-38: Particular
60601-2-38
Requirements for the Safety of Electrically Operated Hospital
Beds
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-39: Particular
60601-2-39
Requirements for Basic Safety and Essential Performance of
Peritoneal Dialysis Equipment
CAN/CSA C22.2 No. 60601-2-4 Medical Electrical Equipment Part 2-4: Particular
Requirements for the Safety of Cardiac Defibrillators
SCOPE OF ACCREDITATION
32
Standards Council of Canada Accredited Laboratory No. 12
CAN/CSA C22.2 No.
60601-2-40
Medical Electrical Equipment - Part 2-40: Particular
Requirements for the Safety of Electromyographs and Evoked
Response Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-41: Particular
60601-2-41
Requirements for the Basic Safety and Essential Performance
of Surgical Luminaires and Luminaires for Diagnosis
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-43: Particular
60601-2-43
Requirements for the Basic Safety and Essential Performance
of X-Ray Equipment for Interventional Procedures
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-45: Particular
60601-2-45
Requirements for the Safety of Mammographic X-Ray
Equipment and Mammographic Stereotactic Devices
Except for: Cl. 22.103.3 - Biopsy needle positioning accuracy
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-46: Particular
60601-2-46
Requirements for the Safety of Operating Tables
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-47: Particular
60601-2-47
Requirements for the Safety, Including essential Performance,
of Ambulatory Electrocardiographic Systems
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-49: Particular
60601-2-49
Requirements for the Safety of Multifunction Patient
Monitoring Equipment
CAN/CSA C22.2 No. 60601-2-5 Medical Electrical Equipment - Part 2-5: Particular
Requirements for the Basic Safety and Essential Performance
of Ultrasonic Physiotherapy Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-50: Particular
60601-2-50
Requirements for the Basic Safety and Essential Performance
of InfantPhototherapy Equipment
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-51: Particular
60601-2-51
Requirements for Safety, Including Essential Performance, of
Recording and Analysing Single Channel and Multichannel
Electrocardiographs
CAN/CSA C22.2 No. 60601-2-7 Medical Electrical Equipment - Part 2-7: Particular
Requirements for the Safety of High-Voltage Generators of
Diagnostic X-Ray Generators
CAN/CSA C22.2 No. 60601-2-8 Medical Electrical Equipment - Part 2-8: Particular
Requirements for the Safety of Therapeutic X-ray Equipment
Operating in the Range 10 kV to 1 MV
CAN/CSA C22.2 No.
Medical Electrical Equipment - Part 2-30: Particular
80601-2-30-10
Requirements for the Basic Safety and Essential Performance
of Automated Non-Invasive Sphygmomanometers (Adopted
IEC 80601-2-30:2009, First Edition, 2009-01)
CAN/CSA-C22.2 No 601.1B-90
Amendment 2 to CAN/CSA-C22.2 No 601.1-M90, Medical
(R06)
CAN/CSA-C22.2 No. 601.1.3
Medical Electrical Equipment - Part 1: General Requirements
for Safety - 3. Collateral Standard: General Requirements for
Radiation Protection in Diagnostic X-Ray Equipment
CAN/CSA-C22.2 No.
Supplement No. 1-94 to CAN/CSA-C22.2 No. 601.1-M90 601.1S1-94 (R1999)
Medical Electrical Equipment - Part 1: General Requirements
SCOPE OF ACCREDITATION
33
Standards Council of Canada Accredited Laboratory No. 12
CAN/CSA-C22.2 No.
601.2.19A-92 (R01)
CAN/CSA-C22.2 No.
601.2.20A-92 (R01)
CAN/CSA-C22.2 No. 601.2.21
CAN/CSA-C22.2 No.
601.2.21A-98
CAN/CSA-C22.2 No.
601.2.25A-94
CAN/CSA-C22.2 No. 601.2.31
CAN/CSA-C22.2 No. 601.2.32
CAN/CSA-C22.2 No.
60601-1-11
CAN/CSA-C22.2 No.
60601-1-3-09
CAN/CSA-C22.2 No.
60601-2-36
CAN/CSA-C22.2 No.
60601-2-41-02 (R07)
CAN/CSA-C22.2 No.
60601-2-44
CAN/CSA-C22.2 No.
60601-2-50-10
TC 1:2011 (Corrigendum 1)
SCOPE OF ACCREDITATION
for Safety (Adopted IEC 601-1, Amendment 1:1991)
Amendment 1:2001 to CAN/CSA-C22.2 No.
601.2.19-92-Medical Electrical Equipment - Part 2: Particular
Requirements for Safety of Baby Incubators
(Adopted Amendment 1:1996 to IEC 601-2-19:1990)
Amendment 1:2001 to CAN/CSA-C22.2 No.
601.2.20-92-Medical Electrical Equipment - Part 2: Particular
Requirements for the Safety of Transport Incubators
(Adopted Amendment 1:1996 to IEC 601-2-20:1990)
Medical Electrical Equipment - Part 2: Particular Requirements
for the Safety of Infant Radiant Warmers
Amendment 1:2001 to CAN/CSA-C22.2 No.
601.2.21-98,Medical Electrical Equipment - Part 2: Particular
Requirements for the Safety of Infant Radiant Warmers
(Adopted Amendment 1:1996 to IEC 601-2-21:1994)
Amendment 1: 2002 to CAN/CSA C22.2 No. 601.2.25-94
Medical Electrical Equipment - Part 2-25: Particular
Requirements for the Safety of Electrocardiographs
(Adopted Amendment 1:1999 to CEI/IEC 601-2-25:1993)
Amendment 1:2001 to CAN/CSA-C22.2 No. 601.2.31-98,
Medical Electrical Equipment - Part 2-31: Particular
Requirements for the Safety of External Cardiac Pacemakers
with Internal Power Source
Medical Electrical Equipment - Part 2: Particular Requirements
for the Safety of Associated Equipment of X-Ray Equipment
Medical Electrical Equipment - Part 1-11: General
Requirements for Basic Safety and Essential Performance Collateral Standard: Requirements for Medical Electrical
Equipment and Medical Electrical Systems Used in the Home
Healthcare Environment
Medical Electrical Equipment - Part 1-3: General Requirements
for Basic Safety and Essential Performance - Collateral
Standard: Radiation Protection in Diagnostic X-Ray Equipment
Medical Electrical Equipment - Part 2: Particular Requirements
for the Safety of Equipment for Extracorporeally Induced
Lithotripsy
Medical Electrical Equipment - Part 2-41: Particular
Requirements for the Safety of Surgical Luminaires and
Luminaires for Diagnosis (Adopted IEC 60601-2-41:2000,
First Edition, 2000-02)
Medical Electrical Equipment - Part 2-44: Particular
Requirements for the Basic Safety and Essential Performance
of X-Ray Equipment for Computed Tomography
Technical Corrigendum 1:2011 to CAN/CSA-C22.2 No.
60601-2-50-10, Medical Electrical Equipment - Part 2-50:
Particular Requirements for the Basic Safety and Essential
Performance of Infant Phototherapy Equipment (Adopted IEC
60601-2-50:2009, Second Edition, 2009-03)
34
Standards Council of Canada Accredited Laboratory No. 12
CAN/CSA-C22.2 No.
60601-2-52-11
CAN/CSA-C22.2 No.
60601-2-54
CAN/CSA-C22.2 No.
80601-2-58-10
CAN/CSA-C22.2 No.
80601-2-59-10
CAN/CSA-C22.2 No.
60601-1-2A-03
CAN/CSA-Z10535-03
CSA C22.2 114
CSA C22.2 125
CSA C22.2 601.1
CSA C22.2 601.1.2
CSA C22.2 601.2.1
CSA C22.2 601.2.10
CSA C22.2 601.2.11
CSA C22.2 601.2.11S1
CSA C22.2 601.2.12
CSA C22.2 601.2.19
CSA C22.2 601.2.20
Medical Electrical Equipment - Part 2-50: Particular
Requirements for the Basic Safety and Essential Performance
of Medical Beds
(Adopted IEC 60601-2-52:2009, First Edition, 2009-12)
Medical Electrical Equipment - Part 2-54: Particular
Requirements for the Basic Safety and Essential Performance
of X-Ray Equipment for Radiography and Radioscopy
(Adopted IEC 60601-2-54:2009, First Edition, 2009-06)
Medical Electrical Equipment - Part 2-58: Particular
Requirements for the Basic Safety and Essential Performance
of Lens Removal Devices and Vitrectomy Devices for
Ophthalmic Surgery
(Adopted IEC 80601-2-58:2008, First Edition, 2008-10)
Medical Electrical Equipment - Part 2-59: Particular
Requirements for the Basic Safety and Essential Performance
of Screening Thermographs for Human Febrile Temperature
Screening
(Adopted IEC 80601-2-59:2008, First Edition, 2008-10)
Amendment 1:2006 to CAN/CSA-C22.2 No.
60601-1-2-03. Medical Electrical Equipment - Part 1-2:
General
Requirements for Safety - Collateral Standard:
Electromagnetic Compatibility - Requirements and Tests
(Adopted Amendment 1:2004 to IEC 60601-1-2:2001)
Hoists for the Transfer of Disabled Persons - Requirements and
Test Methods (Adopted ISO 10535:1998, first edition,
1998-10-15, with Canadian deviations)
Diagnostic Imaging and Radiation Therapy Equipment
Electromedical Equipment
Medical Electrical Equipment, Part 1: General Requirements
for Safety
Medical Electrical Equipment, Part 1: General Requirements
for Safety -- 2. Collateral Standard: Electromagnetic
Compatibility -- Requirements and Tests
Medical Electrical Equipment, Part 2: Particular Requirements
for Medical Electron Accelerators in the Range 1 MeV to 50
MeV
Medical Electrical Equipment, Part 2: Particular Requirements
for the Safety of Nerve and Muscle Stimulators
Medical Electrical Equipment, Part 2: Particular Requirements
for the Safety of Gamma Beam Therapy Equipment
Supplement No. 1-94 to CAN/CSA C22.2 No. 601.2.11-92
Medical Electrical Equipment, Part 2: Particular Requirements
for the Safety of Anaesthetic Machines
Baby Incubators
Medical Electrical Equipment, Part 2: Particular Requirement
for the Safety of Transport Incubators
CSA C22.2 601.2.25
SCOPE OF ACCREDITATION
35
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 601.2.28
CSA C22.2 601.2.3
CSA C22.2 601.2.6
CSA-Z7168.3
IEC 60601-2-35
UL 60601-1
Medical Electrical Equipment, Part 2: Particular Requirements
for the Safety of Electrocardiographs
Medical Electrical Equipment, Part 2: Particular Requirements
for the Safety of X-Ray Source Assemblies and X-Ray Tube
Assemblies for Medical Diagnosis
Medical Electrical Equipment, Part 2: Particular Requirements
for the Safety of Short-Wave Therapy Equipment
Medical Electrical Equipment, Part 2: Particular Requirements
for the Safety of Microwave Therapy Equipment
Anaesthetic Machines for Medical Use
Part 2-35: Particular Requirements for the Basic Safety and
Essential Performance of Heating Devices Using Blankets,
Pads and Mattresses and Intended for Heating in Medical Use
Medical Electrical Equipment part 1: General Requirements for
Safety Adopted IEC 601-1 2nd Edition (90) + Am1 and Am2
Motors, Generators, and Machines:
(Energy Efficiency)
CSA C390
Energy Efficiency Test Methods for Three-Phase Induction
Motors (Efficiency Quoting Method and Permissible Efficiency
Tolerance)
Except for: 51-200HP motors
Complete Unit
CSA C22.2 100
CSA C22.2 33
CSA C22.2 77
UL 2111
Motors and Generators
Except for: 51-200HP motors
Construction and Test of Cranes and Hoists
Except for: Clause 8.3 - Slip Clutch Test
Motors with Inherent Overheating Protection
Overheating Protection for Motors
Scientific Instruments: (For biological, chemical electrical, mechanical optical and physical
examination)
(Complete Units)
CAN/CSA-C22.2 No.
61010-2-081
SCOPE OF ACCREDITATION
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use - Part 2-081:
Particular Requirements for Automatic and Semi-Automatic
Laboratory Equipment for Analysis and Other Purposes
(Adopted CEI/IEC 61010-2-081:2001, first edition, 2001-12,
including Amendment 1:2003)
36
Standards Council of Canada Accredited Laboratory No. 12
CAN/CSA-C22.2 No.
61010-2-101
CSA C22.2 1010.1
CSA C22.2 1010.2.010
CSA C22.2 1010.2.020
CSA C22.2 1010.2.031
CSA C22.2 1010.2.032
CSA C22.2 1010.2.041
CSA C22.2 1010.2.051
CSA C22.2 1010.2.061
CSA C22.2 No. 61010-031
CSA C22.2 No. 61010-1
CSA C22.2 No. 61010-2-010
Safety Requirements for Electrical Equipment for
Measurement, Control and Laboratory Use - Part 2-101:
Particular Requirements for In Vitro Diagnostic (IVD) Medical
Equipment (Adopted CEI/IEC 61010-2-101:2002, first edition,
2002-01)
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use, Part 1: General
Requirements
Except for:
Cl. 12.6 ref IEC 825, Laser Measurement
Safety Requirements for Electrical Equipment for
Measurement, Control and Laboratory Use -- Part 2 010:
Particular Requirements for Laboratory Equipment for the
Heating of Materials
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use -- Part 2-020:
Particular Requirements for Laboratory Centrifuges
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use -- Part 2-031:
Particular Requirements for Hand-held Probe Assemblies for
Electrical Measurement and Test
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use -- Part 2-032:
Particular Requirements for Hand-Held Current Clamps for
Electrical Measurement and Test
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use -- Part 2-041:
Particular Requirements for Autoclaves using Steam for the
Treatment of Medical Materials, and for Laboratory Processes
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use -- Part 2-051:
Particular Requirements for Laboratory Equipment for Mixing
and Stirring
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use -- Part 2-061:
Particular Requirements for Laboratory Atomic Spectrometers
with Thermal Atomization and Ionization
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use - Part 2-031:
Particular Requirements for Hand-held Probe Assemblies for
Electrical Measurement and Test
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use, Part 1: General
Requirements
Safety Requirements for Electrical Equipment for
Measurement, Control and Laboratory Use - Part 2-010:
Particular Requirements for Laboratory Equipment for the
Heating of Materials
CSA C22.2 No. 61010-2-020
SCOPE OF ACCREDITATION
37
Standards Council of Canada Accredited Laboratory No. 12
CSA C22.2 No. 61010-2-040
CSA C22.2 No. 61010-2-051
CSA C22.2 No. 61010-2-061
UL 3101-1
UL 3111-1
UL 61010-2-010
UL 61010-2-041
UL 61010-2-051
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use - Part 2-020:
Particular Requirements for Laboratory Centrifuges
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use - Part 2-040:
Particular Requirements for Sterilizers and
Washer-Disinfectors used to Treat Medical Materials
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use - Part 2-051:
Particular Requirements for Laboratory Equipment for Mixing
and Stirring
Safety Requirements for Electrical Equipment for
Measurement, Control, and Laboratory Use - Part 2-061:
Particular Requirements for Laboratory Atomic Spectrometers
with Thermal Atomization and Ionization
Electrical Equipment for Laboratory Use; Part 1: General
Requirements
Electrical Measuring and Test Equipment; Part 1: General
Requirements
Electrical Equipment for Laboratory Use; Part 2: Particular
Requirements for Laboratory Equipment for the Heating of
Materials
Electrical Equipment for Laboratory Use; Part 2: Particular
Requirements for Autoclaves Using Steam for Treatment of
Medical Materials and for Laboratory Processes
Electrical Equipment for Laboratory Use; Part 2: Particular
Requirements for Laboratory Equipment for Mixing and
Stirring
ENVIRONMENTAL AND OCCUPATIONAL HEALTH AND SAFETY
Occupational Health and Safety:
Personal Protection
(Fall Arresting Equipment, Head, and Limbs)
ANSI Z359.1
ANSI Z87.1
ANSI/ASSE Z359.12
ANSI/ASSE Z359.13
ASTM F2413
SCOPE OF ACCREDITATION
Safety Requirements for Personnel Fall Arrest Systems,
Subsystems and Components
Practice for Occupational and Educational Eye and Face
Protection
Except for: testing using European Head forms.
Connecting Components for PFAS
Personal Energy Absorbers and Energy Absorbing Lanyards
American National Standard for Personnel ProtectionProtective Footwear
38
Standards Council of Canada Accredited Laboratory No. 12
CSA Z195
CSA Z259.1
CSA Z259.10
CSA Z259.11
CSA Z259.12
CSA Z259.2.1
CSA Z259.2.2
CSA Z259.2.3
CSA Z76.1
Protective Footwear
Safety Belts and Lanyards
Full Body Harnesses
Energy Absorbers and Lanyards
Connecting Components for Personal Fall Arrest Systems
(PFAS)
Fall Restrict Equipment for Wood pole Climbing (On-site
testing according to CAN-P-1632)
Except for: 6.2 Down-the-pole tests;
6.3 Off-the-pole test; and
6.4.1 Dynamic strength test - Complete device.
Fall Arresters, Vertical Lifelines and Rails
Self-retracting Devices for PFAS
Descent Control Devices
Reclosable Child-Resistant Packages
CSA Z94.3
Only for: Physical tests
Eye and Face Protectors
CSA Z259.14
Warning Devices
CAN/ULC-S319
CSA C22.2 205
UL 1023
UL 1637
UL 2017
UL 2075
UL 294
UL 912
Electronic Access Control Systems
Signal Equipment
Household Burglar Alarm System Units
Home Health Care Signaling Equipment
General-Purpose Signaling Devices and Systems
Gas and Vapor Detectors and Sensors
Access Control System Units
Highway Emergency Signals
Water Quality:
(Water)
NSF/ANSI 42
NSF/ANSI 53
NSF/ANSI 60
NSF/ANSI 61
SOP383.13
SOP383.15
SOP383.21
SCOPE OF ACCREDITATION
Drinking Water Treatment Units - Aesthetic Effects
Refer to methods outlined under NSF/ANSI 61
Drinking Water Treatment Units - Health Effects
Refer to methods outlined under NSF/ANSI 61
Drinking Water Treatment Chemicals - Health Effects
Refer to methods outlined under NSF/ANSI 61
Drinking Water Treatment Units - Health Effects
Measuring pH (modified EPA 150.1)
Measuring Turbidity of a Solution (modified from EPA PA
180.1)
Analysis Of Total Dissolved Solids (TDS) In Water - Filterable
39
Standards Council of Canada Accredited Laboratory No. 12
SOP383.22
SOP383.32
Residue Method (modified SM 2540C)
Determination of Trace Elements in Waters and Wastes by
Inductively Coupled Plasma - Mass Spectrometry (modified
EPA 200.8)
Analysis of Total Dissolved Solids (TDS) in Water
Industrial Chemicals and Wastes
NSF/ANSI-46
NSF-41
Evaluation of Components and Devices Used in Wastewater
Treatment Systems
Non-liquid Saturated Treatment Systems
MACHINERY
Boilers, Pressure Vessels and Piping:
Pumps and Related Equipment
CSA C22.2 108
Liquid Pumps
Stationary Equipment:
Hoists
CSA C22.2 33
Construction and Test of Electric Cranes and Hoists
Except for: Clause 8.3 - Slip Clutch Test
Transportation, Agricultural and Construction Vehicles and Components:
(Generally Applicable Tests, Braking Systems, Interior Materials, and Restraint Systems)
CMVSS 106
Brake Hoses
Boats and Ships
CSA C22.2 183.1
CSA C22.2 183.2
Transport Canada TP1861E
Alternating-Current (AC) Electrical Installations on Boats
DC Electrical Installations on Boats
Collision Regulation Standards for Light Shape Sound Signal
Appliances and Radar Reflectors
MARKETPLACE PRODUCTS-CONSUMER AND BUSINESS
SCOPE OF ACCREDITATION
40
Standards Council of Canada Accredited Laboratory No. 12
Furniture and Consumer Articles:
Hazardous Products
(Packaging Materials - Toys
See also Occupational Health and Safety)
CSA C22.2 149
Electrically Operated Toys
NON METALLIC MINERALS AND PRODUCTS
Energy Equipment: (Appliances)
Handling of Liquid Fuels
(Dispensing Devices - Tanks)
CSA B306
CSA B346
CSA B376
CSA C22.2 No. 22
Portable Fuel Tanks for Marine Use
Power-Operated Dispensing Devices for Flammable Liquids
Portable Containers for Gasoline and Other Petroleum Fuels
Electrical Equipment for Flammable and Combustible Fuel
Dispensers
Miscellaneous, Energy Equipment
CSA B140.9.2
CSA B140.9.4
Portable Pressurized Type Liquid Petroleum Fuelled Camp
Stoves
Portable Pressurized-Type, Liquid Petroleum Fuelled Lamps
and Lanterns
Natural Gas Fired Appliances
and Propane Fired Appliances
ANSI Z21.20 CAN1-6.4
ANSI Z21.63/CSA 11.3
CAN1-11.3
ANSI Z21.69/CSA 6.16
ANSI Z21.72/CSA 11.2
ANSI Z21.73/CSA 11.1
ANSI Z21.74
ANSI Z21.87/CSA 4.6
ANSI/AGA NGV3/CGA 12.3
CAN/CGA-9.2
SCOPE OF ACCREDITATION
Automatic Gas Ignition Systems and Components
Portable Type Gas Camp Heaters
Connectors for Movable Gas Appliances
Portable Type Gas Camp Stoves
Portable Type Gas Camp Lights
Portable Type Gas Camp Refrigerators
Automatic Gas-Shut-Off Valves and Devices for Hot Water
Supply Systems
Natural Gas Vehicle (NGV) Fuel System Components
Manually Operated Shut-Off Valves for Gas Piping Systems
41
Standards Council of Canada Accredited Laboratory No. 12
CAN1-11.4
CAN1-12.2
CGA 2.29
CGA 3.16
CGA 6.23/ANSI Z21.77
CSA 6.18
CSA 6.20/ANSI Z21.78
CSA 6.22/ANSI Z21.80
CSA 6.25/ANSI Z21.81
CSA 6.29/ANSI Z21.92
Portable Type Gas Camp Refrigerators
Propane Fuel System Components for Use on Highway
Vehicles
Hand-Held Torches for Fuel Gas
Lever Operated Non-Lubricated Gas Shut-Off Valves
Manually-Operated Piezo-Electric Spark Gas Ignition Systems
and Components
Internal Relieved Service Regulators for Natural Gas
Combination Gas Controls for Gas Appliances
Line Pressure Regulators
Cylinder Connection Devices
Manually Operated Electric Gas Ignition Systems and
Components
Notes:
CAN-P-4E (ISO/IEC 17025): General Requirements for the Competence of Testing and Calibration
Laboratories (ISO/IEC 17025-2005)
Chantal Guay, ing., P. Eng.
Vice President, Accreditation
Services
Date: 2016-04-26
Number of Scope Listings: 802
SCC 1003-15/7
Partner File #0
Partner: None
SCOPE OF ACCREDITATION
42