EBP1400X and EBP1400F
SURE-LITES
page 1
Installation Instructions for EBP1400X and EBP1400F
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS
BE OBSERVED INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1.
2. Do not use outdoors.
3. Do not mount near gas or electric heaters.
4. Equipment should be mounted in locations and at heights where it will not readily be subject to
tampering by unauthorized personnel.
5. The use of accessory equipment not recommended by Sure-Lites may cause an unsafe condition.
6. Do not use this equipment for other than its intended purpose.
7.
Risk of Fire/Electric
Shock
If not qualified, consult an
electrician.
SAVE THESE INSTRUCTIONS
Risk of Electric Shock
Disconnect power at fuse
or circuit breaker before
installing or servicing.
Note 1. To prevent high voltage from being present on the output terminals (red/white, red, and yellow), do not connect the test button indicator light to
the EBP until Step 7 of the installation instructions.
Note 2. This product is for use with most 2’ through 8’ (6W-215W single and bipin fluorescent lamps including energy saving, circline, U-shaped and biax.
For specific lamp compatibility, please see the table later in the instructions.
Note 3. Make sure all of the connections are in accordance with the National Electrical Code and any local regulations.
Note 4. To reduce the risk of electrical shock, disconnect both normal and emergency power supplies and the test button indicator light (which
disconnects the battery) before servicing.
Note 5. This emergency ballast is for factory or field installation in the ballast channel.
Note 6. This product is for use in indoor fixtures. This product is not intended for use near air handling heated air outlets or in wet or hazardous locations.
Note 7. An unswitched AC power source is required (120, 240, or 277 volts).
Note 8. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field replaceable. Contact the manufacturer for
information on service.
Note 9. Servicing should be performed by qualified service personnel.
For use in temperature rating
20°C to 55°C
CONTAINS NICKEL-METAL
HYDROXIDE RECHARGEABLE
BATTERY. MUST BE RECYCLED
OR DISPOSED OF PROPERLY.
EBP1400X
EBP1400F
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
Ni - MH
EBP1400X and EBP1400F
SURE-LITES
page 2
INSTALLATION
WARNING: TO PREVENT HIGH VOLTAGE ON RED / WHITE, RED, AND YELLOW OUTPUT TERMINALS PRIOR TO
INSTALLATION, THE TEST BUTTON / INDICATOR LIGHT MUST BE DISCONNECTED. CONNECT THE TEST BUTTON /
INDICATOR LIGHT AFTER INTSALLATION.
Note: Make sure that the necessary branch circuit wiring is available. An unswitched source of power is required.
Step 1. Disconnect AC power from the fixture. Remove the ballast channel cover and install the emergency ballast either in the
ballast channel (see illustrations 1 & 2) or on top of the fixture (see illustration 3 / EBP1400X only).
ILLUSTRATION 1
ILLUSTRATION 2
Emergency
Ballast
ILLUSTRATION 3
Emergency
Ballast
Wire Bundle
Cover
Emergency
Ballast
Test Button/
Indicator Light
Drill 1/8˝ Hole
for Mounting Screws
Test Button/
Indicator Light
Wire Bundle
Cover
Ballast
Channel
Cover
1/2˝ Std. Knockout
7/8˝ Hole w/Bushing
EBP1400X only
Step 2. Select the appropriate wiring diagram to connect the emergency ballast to the AC ballast and lamp. Make sure all
connections are in accordance with the National Electrical Code and any local regulations. (See Illustrations 4 and
5 for terminals).
RED / WH
RED
BLUE
BLUE / WH
YELLOW
AUX
COMMON
Emergenc
Suitable f
Color coded label
located here.
YELLOW / BK
AUX COM
AUX
N.C.
AUX
N.O.
LINE HOT
120/240/277
LINE
NEUTRAL
AUX N.C.
LINE HOT
120/240/277
LINE
NEUTRAL
AUX N.O.
1121 Highway
Peachtree Ci
Terminal labels located
here.
ILLUSTRATION 5
TEST B
LIGHT C
ILLUSTRATION 4
Test Button / Indicator Light Connector
Step 3. Refer to the lamp compatibility table for the HIGH (Red) or Low (Red / White) connection per the lamp(s) being
illuminated by the emergency ballast.
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
EBP1400X and EBP1400F
SURE-LITES
page 3
Lamp Compatibility Tables
Lamp Type
Number of
Emergency
Lamps
Lamps Connected to
Low/High (Red) Output
Wattage
T5, T5HO
1
HIGH (RED)
6-39
T5 CIRC,T9 CIRC
1
HIGH (RED)
20-55
T8, T8U
1
HIGH (RED)
15-32
T8HO
1
HIGH (RED)
48
T12
1
HIGH (RED)
20-48
BIAX
1
HIGH (RED)
18-55
T5HO
1
LOW (RED / WHITE)
54-80
T8
1
LOW (RED / WHITE)
36-59
T8HO
1
LOW (RED / WHITE)
65-86
T12, T12HO/VHO
1
LOW (RED / WHITE)
56-165
T5
2
HIGH (RED)
6
T8
2
HIGH (RED)
15-32
BIAX, T12
2
HIGH (RED)
18-20
T5
2
LOW (RED / WHITE)
13-35
T5HO
2
LOW (RED / WHITE)
24-39
T8HO
2
LOW (RED / WHITE)
48
T8U
2
LOW (RED / WHITE)
16-32
T12
2
LOW (RED / WHITE)
34-40
ILLUSTRATION 6
ILLUSTRATION 7
TROFFER STYLE FIXTURE
STRIP STYLE FIXTURE
Fixture
Emergency
Ballast
Ballast Channel
Cover
Leads to Test Button/
Indicator Light
7/8" Punch
7/8" Bushing
Inserted into
Ballast Channel
Cover
Plastic Tubing
(cut to necessary
length)
Test Button/
Indicator Light
Test Button/
Indicator Light
Nut
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
SURE-LITES
EBP1400X and EBP1400F
page 4
Step 4. Install the test button / indicator light through the ballast channel cover of a troffer (Illustration 1 & 6) or through the
side of a strip fixture (Illustration 2 & 7). Drill or punch a7/8” hole to install the test button / indicator light as shown in
illustration 6. Drill or punch a 1/2” hole to install the test button / indicator light as shown in illustration 7. Install the test
button / indicator light as shown in the selected illustration. Apply the two included labels (“Charging Indicator Light”
and “Emergency Light Push to Test”) adjacent to the test button indicator light.
Step 5. In a readily visible location, attach the included label “CAUTION – This unit Has More Than One Power Connection
Point. To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses and the Test
Button / Indicator Light Before Servicing”.
Step 6.
In an area readily visible during relamping, attach the included relamping label. Write in the lamp type and wattage.
Step 7.
After installation is complete, connect the test button / indicator light, and supply AC power to the emergency ballast,
and replace covers while being careful not to pinch wires.
Step 8.
A short term discharge test may be conducted after the emergency ballast has been charging for one hour.
Charge for 24 hours before conducting a long – term discharge test. Refer to OPERATION.
OPERATION:
When AC power is applied, the charging indicator light is illuminated, indicating the battery is being charged. When
power fails, the emergency ballast automatically switches to emergency power, operating one or two lamps at
reduced illumination for at least 90 minutes.
MAINTENANCE:
Although no routine maintenance is required to keep the emergency ballast functional, it should be checked
periodically to comply with local codes. The following schedule is recommended:
Step 1.
Visually inspect the charging light monthly. It should be illuminated
Step 2.
Test the emergency operation of the fixture at 30 day intervals for a minimum of 30 seconds. Depending on
installation, one or two lamps should operate at reduced illumination.
Step 3.
Conduct a 90 – minute discharge test once a year. Depending on installation, one or two lamps should operate at
reduced illumination for at least 90 minutes.
Refer any service requirements indicated by these checks to qualified personnel.
Note: After installing the test button / indicator light, mark it with the appropriate label.
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
AC BALLAST
LAMP ("EMERGENCY")
RED
RED
BLUE
BLUE
YELLOW
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY BALLAST
YELLOW/BK
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
YELLOW
YELLOW
LINE NEUTRAL
AC BALLAST
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
YELLOW
YELLOW
LINE NEUTRAL
AC BALLAST
RED
RED
BLUE
BLUE
LAMP-2 ("EMERGENCY")
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
LAMP-2 ("EMERGENCY")
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
LINE HOT
LAMP ("EMERGENCY")
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY BALLAST
YELLOW/BK
YELLOW
BLUE/WH
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
YELLOW
YELLOW/BK
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY BALLAST
2 LAMP RAPID START SERIES LAMP
SERIES YELLOW FILAMENT
AC BALLAST
LAMP-1
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
AUX COM
RED
LINE NEUTRAL
LINE HOT
1 LAMP INSTANT START
LAMP-1
RED
RED
BLUE
BLUE
YELLOW
YELLOW/BK
EMERGENCY BALLAST
2 LAMP RAPID START SERIES / PARALLEL LAMP
PARALLEL YELLOW FILAMENT
LINE HOT
LINE NEUTRAL
LINE HOT
1 LAMP RAPID START
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
SURE-LITES
EBP1400X and EBP1400F
page 5
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLAST. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS
WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION
YELLOW
YELLOW
BLUE
BLUE
LINE NEUTRAL
LINE HOT
YELLOW
YELLOW
LINE NEUTRAL
LINE HOT
LAMP-2 ("EMERGENCY")
LAMP-1
RED
RED
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
YELLOW
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
AC BALLAST
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
LAMP-3
LAMP-2 ("EMERGENCY")
LAMP-1
RED
RED
BLUE/WHT
BLUE/WHT
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
YELLOW
YELLOW/BK
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY BALLAST
3 LAMP RAPID START SERIES LAMP
PARALLEL YELLOW FILAMENT
AC BALLAST
BLUE
BLUE
YELLOW/BK
EMERGENCY BALLAST
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
2 LAMP RAPID START OSRAM SYLVANIA SERIES
LAMP PARALLEL YELLOW FILAMENT
LINE NEUTRAL
LINE HOT
LINE NEUTRAL
LINE HOT
AC BALLAST
AC BALLAST
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE
BLUE/WH
LAMP-3 ("EMERGENCY")
LAMP-2
LAMP-1
RED OR YELLOW
BLUE
BLUE
BLUE
YELLOW/BK
BLUE/WH
YELLOW
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY BALLAST
3 LAMP INSTANT START
LAMP-2 ("EMERGENCY")
LAMP-1
RED
BLUE
BLUE
YELLOW
YELLOW/BK
EMERGENCY BALLAST
2 LAMP INSTANT START
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
LINE NEUTRAL
(UNSWITCHED) 120/240/2277
SWITCHED OR UNSWITCHED LINE HOT
SURE-LITES
EBP1400X and EBP1400F
page 6
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLAST. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS
WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION
YELLOW
YELLOW
LINE HOT
LINE NEUTRAL
YELLOW
YELLOW
BROWN
BROWN
LINE HOT
LINE NEUTRAL
LAMP-4 ("EMERGENCY")
LAMP-3
LAMP-2
LAMP-1
RED
RED
BLUE/WHT
BLUE/WHT
EMERGENCY
BALLAST
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
RED
RED
BLUE
BLUE
LAMP-3 ("EMERGENCY")
LAMP-2
LAMP-1
AC BALLAST
RED/WHT
RED/WHT
EMERGENCY
BALLAST
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
YELLOW/BK
YELLOW
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
3 LAMP RAPID START PARALLEL LAMP
PARALLEL YELLOW FILAMENT
AC BALLAST
BLUE
BLUE
YELLOW/BK
YELLOW
4 LAMP RAPID START SERIES LAMP
PARALLEL YELLOW FILAMENT
YELLOW
YELLOW
LINE NEUTRAL
LINE HOT
YELLOW
YELLOW
LINE NEUTRAL
LINE HOT
LAMP-4 ("EMERGENCY")
LAMP-3
LAMP-2
LAMP-1
RED
RED
BLUE
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
YELLOW
BLUE/WH
BLUE
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
LAMP-4 ("EMERGENCY")
LAMP-3
LAMP-2
LAMP-1
AC BALLAST
BLUE/WHT
BLUE/WHT
RED/WHT
RED/WHT
BLUE
BLUE
RED
RED
EMERGENCY
BALLAST
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
YELLOW/BK
YELLOW
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
4 LAMP RAPID START PARALLEL LAMP
PARALLEL YELLOW FILAMENT
AC BALLAST
YELLOW/BK
EMERGENCY BALLAST
4 LAMP INSTANT START
SURE-LITES
EBP1400X and EBP1400F
page 7
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLAST. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS
WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION
EBP1400X and EBP1400F
SURE-LITES
page 8
WIRING DIAGRAMS FOR 1-LAMP EMERGENCY OPERATION
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLAST. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS
BI LEVEL BALLAST
SWITCHED LINE HOT
EMERGENCY BALLAST
YELLOW/BK
SWITCHED LINE HOT
LINE NEUTRAL
YELLOW
BLUE/WH
WIRE LAMPS USING DIAGRAM PER
# OF LAMPS AND BALLAST TYPE
BI-LEVEL
AC BALLAST
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
AUX COM
AUX NO
LINE NEUTRAL
AUX NC
LINE HOT
(UNSWITCHED) 120/240/277
LINE NEUTRAL
When using the auxillary relay to switch the neutral line, the Emergency
and A.C. ballasts must be on the same branch circuit.
WIRING DIAGRAMS FOR 2-LAMP EMERGENCY OPERATION
LINE NEUTRAL
(UNSWITCHED) 120/240/277
LINE HOT
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
LAMP-2 ("EMERGENCY")
RED
RED
YELLOW
YELLOW
024-117
LAMP-1 ("EMERGENCY")
RED OR RED/WH
CHOOSE BASED
ON LAMP
LINE NEUTRAL
SWITCHED OR UNSWITCHED LINE HOT
AUX NC
AUX NO
AUX COM
BLUE/WH
BLUE
BLUE
BLUE
AC BALLAST
LINE NEUTRAL
EMERGENCY BALLAST
YELLOW/BK
YELLOW
LINE HOT
LAMP-2 ("EMERGENCY")
LAMP-1 ("EMERGENCY")
RED
RED
YELLOW
YELLOW
2 LAMP RAPID START SERIES LAMP
SERIES YELLOW FILAMENT
(UNSWITCHED) 120/240/277
LINE HOT
RED OR RED/WH
CHOOSE BASED
ON LAMP
LINE NEUTRAL LINE NEUTRAL
SWITCHED OR UNSWITCHED LINE HOT
AUX NC
AUX NO
BLUE/WH
BLUE
AUX COM
BLUE
BLUE
AC BALLAST
LINE NEUTRAL
EMERGENCY BALLAST
YELLOW/BK
YELLOW
LINE HOT
2 LAMP RAPID START SERIES / PARALLEL LAMP
PARALLEL YELLOW FILAMENT
FOR OPTIMUM LAMP LIFE, COOPER LIGHTING RECOMMENDS WIRING FOR SINGLE LAMP EMERGENCY OPERATION.
WHILE CAPABLE OF 2 LAMP EMERGENCY OPERATION, NOT ALL AC BALLASTS ARE COMPATIBLE WITH 2 LAMP EMERGENCY OPERATION.
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLAST. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS
LAMP-2 ("EMERGENCY")
LAMP-1 ("EMERGENCY")
BLUE
BLUE
RED
RED
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE/WH
BLUE
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY BALLAST
YELLOW/BK
YELLOW
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
LAMP-3
LAMP-2 ("EMERGENCY")
LAMP-1 ("EMERGENCY")
RED
YELLOW
BLUE/WHT
BLUE/WHT
RED
AC BALLAST
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE/WH
BLUE
YELLOW/BK
YELLOW
LINE HOT
AUX NC
AUX NO
AUX COM
LINE NEUTRAL
EMERGENCY BALLAST
3 LAMP RAPID START SERIES LAMP
PARALLEL YELLOW FILAMENT
AC BALLAST
YELLOW
BLUE
BLUE
LINE NEUTRAL
LINE HOT
YELLOW
YELLOW
LINE NEUTRAL
LINE HOT
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
2 LAMP RAPID START OSRAM SYLVANIA SERIES
LAMP PARALLEL YELLOW FILAMENT
LINE NEUTRAL
LINE HOT
LINE NEUTRAL
LINE HOT
AC BALLAST
AC BALLAST
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE
BLUE/WH
YELLOW
LAMP-3 ("EMERGENCY")
LAMP-2 ("EMERGENCY")
LAMP-1
RED OR YELLOW
BLUE
BLUE
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE/WH
BLUE
YELLOW/BK
YELLOW
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY BALLAST
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
EMERGENCY
BALLAST AUX COM
3 LAMP INSTANT START
LAMP-2 (EMERGENCY)
LAMP-1 (EMERGENCY)
RED
BLUE
BLUE
YELLOW/BK
2 LAMP INSTANT START
LINE NEUTRAL
UNSWITCHED 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
LINE NEUTRAL
UNSWITCHED 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
SURE-LITES
EBP1400X and EBP1400F page 9
WIRING DIAGRAMS FOR 2-LAMP EMERGENCY OPERATION
FOR OPTIMUM LAMP LIFE, COOPER LIGHTING RECOMMENDS WIRING FOR SINGLE LAMP EMERGENCY OPERATION.
WHILE CAPABLE OF 2 LAMP EMERGENCY OPERATION, NOT ALL AC BALLASTS ARE COMPATIBLE WITH 2 LAMP EMERGENCY OPERATION.
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLAST. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS
LINE HOT
YELLOW
YELLOW
LINE NEUTRAL
YELLOW
YELLOW
LINE NEUTRAL
BROWN
BROWN
LINE HOT
RED
RED
BLUE/WHT
BLUE/WHT
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE
BLUE/WH
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY
BALLAST
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 11/28/11
024-117
RED
RED
BLUE
BLUE
LAMP-3 ("EMERGENCY")
LAMP-2 ("EMERGENCY")
LAMP-1
AC BALLAST
RED/WHT
RED/WHT
EMERGENCY
BALLAST
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE/WH
BLUE
YELLOW/BK
YELLOW
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
3 LAMP RAPID START PARALLEL LAMP
PARALLEL YELLOW FILAMENT
LAMP-4 ("EMERGENCY")
LAMP-3 ("EMERGENCY")
LAMP-2
LAMP-1
AC BALLAST
BLUE
BLUE
YELLOW/BK
YELLOW
4 LAMP RAPID START SERIES LAMP
PARALLEL YELLOW FILAMENT
YELLOW
YELLOW
LINE NEUTRAL
LINE HOT
YELLOW
YELLOW
LINE NEUTRAL
LINE HOT
LAMP-2
LAMP-1
RED
RED
BLUE
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
BLUE
BLUE/WH
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
EMERGENCY
BALLAST
LINE NEUTRAL
UNSWITCHED 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
LAMP-4 ("EMERGENCY")
LAMP-3 ("EMERGENCY")
LAMP-2
LAMP-1
AC BALLAST
BLUE/WHT
BLUE/WHT
RED/WHT
RED/WHT
BLUE
BLUE
RED
RED
EMERGENCY
BALLAST
BLUE/WH
BLUE
RED OR RED/WH
CHOOSE BASED
ON LAMP
YELLOW
YELLOW/BK
LINE NEUTRAL
LINE HOT
AUX NC
AUX NO
AUX COM
LINE NEUTRAL
(UNSWITCHED) 120/240/277
SWITCHED OR UNSWITCHED LINE HOT
4 LAMP RAPID START PARALLEL LAMP
PARALLEL YELLOW FILAMENT
LAMP-4 ("EMERGENCY")
LAMP-3 ("EMERGENCY")
AC BALLAST
YELLOW/BK
YELLOW
4 LAMP INSTANT START
SURE-LITES
EBP1400X and EBP1400F page 10
WIRING DIAGRAMS FOR 2-LAMP EMERGENCY OPERATION
FOR OPTIMUM LAMP LIFE, COOPER LIGHTING RECOMMENDS WIRING FOR SINGLE LAMP EMERGENCY OPERATION.
WHILE CAPABLE OF 2 LAMP EMERGENCY OPERATION, NOT ALL AC BALLASTS ARE COMPATIBLE WITH 2 LAMP EMERGENCY OPERATION.
TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLAST. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS