MSD EFI Adapter Kit
Early Hemi© 2003-2005, PN 88815
Late Hemi© 2006-On, PN 88816
Parts Included:
1 - Cam Sensor Harness
1 - Crank Sensor Harness
1 - Map Sensor Harness
7 - Tach Adapters w/single pigtail, Cylinders 2-8
1 - Tach Adapter w/two pigtails, Cylinder 1
Warning: During installation, disconnect the battery cables. When Disconnecting, always remove
the Negative cable first and install it last.
This Harness Kit allows the installation of the MSD 6-Hemi Controller, PN 6013, on Chrysler engine
vehicles equipped with factory EFI systems. The harness connects inline to factory sensors and
provides the 12 volt power source and OEM timing to the controller (Figure 1).
COIL CONNECTIONS
1. Disconnect the factory connectors from
all eight coils.
2. Connect the Tach Adapter with the two
pigtails to Coil 1 and the MSD 6-Hemi.
This Adapter must be connected to coil
1.
3. Connect the remaining seven adapters to
the seven remaining coils. The adapters
with a single pigtail are interchangeable.
COIL 1
PN 88815
for '03-'05,
uses a two-pin
connector.
TO MSD
6-HEMI
PN 88816 for
'06-On, uses
a three-pin
connector.
TO FACTORY
HARNESS
TO FACTORY
HARNESS
TACH
ADAPTER
TO MSD
6-HEMI
TACH
ADAPTER
Figure 1 Coil 1 Tach Adapters.
Hemi is a registered trademark of Chrysler LLC.
MSD
IGNITION
• w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • FA X ( 9 1 5 ) 8 5 7 - 3 3 4 4
INSTALLATION INSTRUCTIONS
CAMSHAFT SENSOR
The Camshaft Sensor is located at the front of the block on
the passenger side.
1. Disconnect the factory harness and connect the female
connector to the sensor.
2. Connect the male connector with the single Brown/White
wire to the MSD 6-Hemi.
3. Connect the male connector with the three wires to the
OEM harness (Figure 2).
TO CAM
SENSOR
SINGLE
BROWN/WHITE
WIRE
TO MSD
6-HEMI
TO OEM
HARNESS
Figure 2 Camshaft Sensor Harness.
CRANKSHAFT SENSOR
TO CRANK
SENSOR
The Crankshaft Sensor is located at the lower rear of the
block on the passenger side.
1. Disconnect the factory harness and connect the female
connector to the sensor.
2. Connect the male connector with the single Orange/Yellow
to the MSD 6-Hemi.
3. Connect the connector with the three wires to the OEM
harness (Figure 3).
SINGLE
ORANGE/YELLOW
WIRE
TO MSD
6-HEMI
TO OEM
HARNESS
Figure 3 Crankshaft Sensor Harness.
MAP SENSOR
The Map Sensor, depending on the application, is located either
at the front of the engine on the manifold or at the back.
1. Disconnect the factory harness and connect the female
connector to the sensor.
2. Connect the male connector with the single Green wire to the
MSD 6-Hemi.
3. Connect the male connector with the three wires to the OEM
harness (Figure 4).
TO MAP
SENSOR
SINGLE
GREEN
WIRE
TO MSD
6-HEMI
TO OEM
HARNESS
Figure 4 Map Sensor Harness.
MSD
IGNITION
• w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • FA X ( 9 1 5 ) 8 5 7 - 3 3 4 4
MSD
IGNITION
TO CAM
SENSOR
OEM
HARNESS
TO CRANK
SENSOR
TO OEM MAP
CONNECTOR
MAP ADAPTER
HARNESS
COIL 2
COIL 4
COIL 6
COIL 8
FRONT
OF
ENGINE
TO MAP SENSOR
COIL
COIL11
COIL
COIL33
COIL
COIL55
COIL 7
Figure 5 Typical Installation of PN 88815 or PN 88816.
TO OEM CAM
CONNECTOR
ADAPTER
TACH ADAPTER
ADAPTER
ADAPTER
TO OEM CRANK
CONNECTOR
CAM ADAPTER
HARNESS
CAM ADAPTER
HARNESS
TACH
LAUNCH LIMITER
STEP-RETARD
12 VOLT
COIL 1 INPUT
COIL 1
ADAPTER
ADAPTER
ADAPTER
ADAPTER
OEM
HARNESS
PN 6013
6-HEMI
INSTALLATION INSTRUCTIONS
• w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • FA X ( 9 1 5 ) 8 5 7 - 3 3 4 4
TECH NOTES
_________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________
_________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ Service
In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty.
When returning MSD components for warranty service, Proof of Purchase must be supplied for verification. After
the warranty period has expired, repair service is based on a minimum and maximum fee.
All returns must have a Return Material Authorization (RMA) number issued to them before
being returned. To obtain an RMA number please contact MSD Customer Service at 1 (888) MSD-7859 or
visit our website at www.msdignition.com/rma to automatically obtain a number and shipping information.
When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include
a detailed account of any problems experienced, and what components and accessories are installed on the vehicle.
The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered
by warranty). For more information, call MSD Ignition at (915) 855-7123. MSD technicians are available from 7:00
a.m. to 6:00 p.m. Monday - Friday (mountain time).
Limited Warranty
MSD IGNITION warrants this product to be free from defects in material and workmanship under its intended normal
use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date
of the original purchase. This warranty is void for any products purchased through auction websites. If found to be
defective as mentioned above, it will be repaired or replaced at the option of MSD Ignition. Any item that is covered
under this warranty will be returned free of charge using Ground shipping methods.
This shall constitute the sole remedy of the purchaser and the sole liability of MSD Ignition. To the extent permitted
by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied,
including any implied warranty of merchantability or fitness. In no event shall MSD Ignition or its suppliers be liable
for special or consequential damages.
*Intended normal use means that this item is being used as was originally intended and for the original application
as sold by MSD Ignition. Any modifications to this item or if it is used on an application other than what MSD Ignition
markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item
will work for the application they are intending. MSD Ignition will accept no liability for custom applications.
MSD
IGNITION
• w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • FA X ( 9 1 5 ) 8 5 7 - 3 3 4 4
© 2007 Autotronic Controls Corporation
FRM28692
Created 07/07
Printed in U.S.A.