GSMX-AUDIO and GSMV-AUDIO, Audio Cable Routing Instructions
For Online Support visit: http://www.security.honeywell.com/hsc/resources/MyWebTech/
Routing Instructions for the GSMX-AUDIO cable.
1.
At the GSMX, loosen the captive cover screw and swing the
cover open. Open the enclosure where the AVS Base Unit
resides.
2.
Ensure power is removed by disconnecting the GSMX’s ECP
cable, and powering down the control and AVS Base Unit.
3.
Connect the 5-pin end of the audio cable to the audio
connector on the GSMX circuit board.
4.
Route the audio cable to the connector on the AVS Base
Unit.
5.
Connect the 4-pin end of the audio cable to the
connector on the AVS Base Unit.
6.
Ensure the audio cable ends are secured with tie
wraps to reduce strain.
7.
At the GSMX, connect the ECP cable. Close the cover
and tighten the captive screw.
8.
At the AVS Base Unit, close the enclosure.
9.
Power up the system, and test.
5-pin connector
4-pin connector
AVS BASE UNIT
1
ON
2
3
4
1
2
3
4
5
AUDIO
CONNECTOR
AUDCBL-001-V0
ON
Routing Instructions for the GSMV-AUDIO cable
1.
2.
At the GSMV, remove the cover screw if present. Using a
medium blade screwdriver, release the communicator’s
cover by depressing the two locking tabs at the bottom of
the unit.
6.
Secure the small PC board and plastic standoff with two
[2] screws. Note the standoff mounts on the right side.
7.
Ensure power is removed by disconnecting the battery
cables, and remove the source of power supplying TB1
pins 1, 2 and 3. Depending on the system, this may be a
transformer or other source.
Route the audio cable to the connector on the AVS Base
Unit and connect the cable.
8.
Ensure the audio cable ends are secured with tie wraps to
reduce strain.
9.
Power up the source of power supplying TB1 pins 1, 2
and 3. Depending on the system, this may be a transformer or other source. Attach the battery cables.
3.
Power down the control and AVS Base Unit.
4.
At the GSMV, remove two [2] screws and standoff that
secure the small PC board, and swing up.
5.
Connect one end of the audio cable to the audio connector
located on the small PC board.
10. Power up the control and AVS Base Unit.
11. Close all enclosure covers (not shown) and secure with
screw as necessary. Test the system.
NNA
ANTE
RNAL ONLY
EXTE MCX
FOR HM, M
O
50
PORT
NA
USE!
ICE
ER
MM E SERV
OGRA ON
LED
P PR LEPH
7720 FOR TE
SMIT
TRAN
NOT
TEN
AN
AL LY
RN ON
XTE CX
R E MM
FO HM,
E!
O
RT US
PO ICE
50
ER RV
UP
C
.5 VA Hr BACK
56
- MC
- 16
AUDCBL-002-V0
GSM S
GPPB
WE DE 2
MO DE 1
MO I
RSS
GSM
GPPS
WEB
MODE 2
MODE 1
RSSI
Ho
Hon
TX
ll
we
ney
ell
eyw
RX
MAC
LABE
TX
MAC
RX
R: 9 FOR 24
67W
POWE AHr
ARY . 3.1 IC: Y2
PRIM ERY: 6V C56
RE
BATT : GIPM
ID
L HE
FCC
MM E SE
RA
D
OG PHON
IT LE
P PR TELE
SM
7720 FOR
TRAN
T
NO
C CKUP
.5 VA Hr BA 56
- 16
: 9 R 24 - MC
WERAHr FO 67W
Y PO . 3.1 IC: Y2
IMAR Y: 6V 6
E
PR ER
C5
ER
PM
TT
BA ID: GI
L H
C
FC
LABE
FOR EXTERNAL ANTENNA
50 OHM, MMCX ONLY
7720P PROGRAMMER PORT
NOT FOR TELEPHONE SERVICE USE!
TRANSMIT LED
PRIMARY POWER: 9 - 16.5 VAC
BATTERY: 6V. 3.1 AHr FOR 24 Hr BACKUP
FCC ID: GIPMC56 IC: Y267W - MC56
MAC LABEL HERE
TX
RX
Honeywell
GSM
GPPS
WEB
MODE 2
MODE 1
RSSI
TB 1
1
2
3
4
5
6
7
8
9
10
11
AVS BASE UNIT
ON
ON
2
3
4
1
2
3
4
5
AUDCBL-003-V0
1
WARRANTY For the latest warranty information go to: http://www.security.honeywell.com/hsc/resources/wa/
Ê800-06409FŠ
800-06409 4/10 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright  2010 Honeywell International Inc.
www.honeywell.com/security