AENOR
AENOR
C
E
E
I
RT FIE
CONSTANT CURRENT CONTROL GEAR FOR LED MODULES AND PROTECTION SYSTEM RESPONSE
Empresa
Registrada
Gestión
Ambiental
ER-0026/1993
CGM-00/041
AL
I
EM
I Net
QU
Pol. Malpica c/ E nº 11 E-50016 Zaragoza ( SPAIN )
Phone: +34 976 573 660
Fax: +34 976 574 960
WEB: http://www.elt.es
E-mail: elt@elt.es
D
Especialidades Luminotécnicas S.A.U.
INSTRUCTIONS MANUAL
LC ...-A
CONSTANT CURRENT CONTROL GEAR FOR LED MODULES
The constant current control gear for LED modules use sensitive electronic components and should be handled with the same
care as any other electronic equipment. In order to achieve a long life and correct functioning, both in the control gear and in the
LED module, it is necessary to follow these manufacturer's recommendations.
SECURITY
A very low voltage installation (LVI) must be carried out whilst taking the necessary precautions in order to respect the safety of all its
parts. The contact or crossing between the mains supply conductors and the very low voltage installation conductors must be avoided
and the insulation between the conductors must be > 4kV.
Maintenance and the changing of parts must be carried out by a qualified person with the mains disconnected and the instructions and
cirrent regulations must be strictly followed.
N
0V
0V
230V
40
0V
400V
N
L1
L2
{!
~
LUMINOUS FLUX REGULATION
It is necessary to ensure that the regulating device or dimmer is designed to operate with LED type charges.
ELT has tested the compatibility of the DLC driver with the models listed in table 1, without excluding other brands existing in the
market. Should you have any doubt, do not hesitate to contact us.
RECOMMENDED DIMMER LIST FOR DLC ELT DRIVERS
VD/C
MW
Reference
}
L2
PROTECTION SWITCHES
Each group of control gear for LED modules must be protected by a magnetothermical circuit breaker and a differential dedicated
circuit breaker. Equipments are resistant to transient overvoltages specified in regulations, and must be installed on different
circuits separated from each other inductive loads (inductive ballasts, motors, fans etc. ....)
ELT
- eDIM 100
- eDIM 400
DINUY
- RE PLA LE1
- RE EL1 LE1
ABB
- 6523 U (ABB y Busch Jaeger)
HPM
- 200E
VADSBO
- LD 220
FINDER
- 15.91.8.230.0000
BTICINO
- 4411
VIMAR
- 19135
ELKO
- 315 GLE 2pol PH
N
WIRING DIAGRAMS
L N
INSULATION TEST
If an insulation test in the circuits which supply the LED driver in the installation is carried out, it must be done applying the test voltage
between the phases and the neutrals all together and the earth wire.
The test voltage must never be applied the phases and the neutral or between phases.
20 cm. min.
Yes
- 2136
- 315 GLE 1pol PH (mininum load 20W)
N
L
N
L
LC ...-B
L
Dimmer
DLC ...-A
DLC ...-B
INRUSH CURRENT
The ignition of LED modules with these control gears is simultaneous. At the moment of connection, the equipment's capacitors
create a strong pulse of current of very short duration, this is called Inrush current. The installation of a maximum number of control
gear depending on the type and characteristics of the magnetothermical protection is recommended. See table.
LED MODULE
L
N
- 20135
Dimmer
TERMINAL BLOCK AND WIRE PREPARATION
2
The use of only one wire with a section between 0,5 and 1,5mm and a stripped length 5mm is recommended.
Don’t put a higher torque than 0,5Nm to the screw.
INSTALATION
Placing a switch in the output of the control gear is not allowed. May cause
damages in control gear and LED module.
- 15.81.8.230.0500
L
NO
Range installation distance
0,5-1,5mm 2
- 19136
- 8160.2 (Niessen)
LC ...-A
LC ...-A-UN
N
OPERATING TEMPERATURE
It must be ensured that the maximum atmospheric temperature in the installation does not exceed the
ta marked on the equipment, and an adequate degree of protection against humidity must be provided.
ºC Under no circumstances must the tc temperature marked on the driver’s casing be exceeded due to the
fact that continued operation at higher temperatures produces a progressive reduction in life
expectancy.
No protection
Manufacturer
400V
Blocks:
It reconnects
when problem
is solved.
It is possible to connect a dimmer or a Leading-edge (beginning of phase) or a trailing-edge (end of phase) type dimmer to obtain a
reduction in the luminous flux. LC
0V
2
N
Limited
output power
When an excess of temperature is
detected, the driver switches off.
After cooling down, it switches on again.
This cycle is permanently repeated.
Block: Stand-by or rest situation
40
2
23
0V
N
L3
V
30
L1
1
wrong
L3
40
L
N
right
40
ELECTRIC POWER SUPPLY
The voltage and frequency of the mains supply must be within the normal operating
range.
In 400V triphase installations, the neutral must always be connected, if it is
interrupted the 400V could reach the equipment and there would be a risk of
damage. When the installation is carried out the charge between the phases must
be as equally balanced as possible.
Short-circuit in
output to lamps
Overtemperature
Overload
Blocks:
Waits for
a lamp
replacement
LC ...-A-UN
DLC ...-A
LC ...-B
DLC ...-B
Types: LC ...-A , LC ...-A-UN , DLC ...-A , LC ...-B y DLC ...-B
¡ Caution !
Absence of lamp.
Open circuit
Type
T Y S YST
Type
CONTROL GEAR +
-
Any procedure at LED lamp connection must be made without electrical supply.
9052101 - December - 2014
Inrush Current
I. Peak
Time
ms
A
Max no. of equipment per circuit breaker
Type B
Type C
RCCB
10A
16A
10A
16A
30mA
LC 125/...-A
18
200
12
16
17
27
43
LC 116/...-A
10
180
22
30
32
52
84
Subjet to changes without notice