Shower Flow Control. Concealed non adjustable time delay, approx 30-40 seconds.
893-2
Size
893-2
Code
Pattern No.
Pack 1 Qty
Description
Pack 2 Qty
A
Code
B
Price (£) ex VAT test
Barcode
C
D
E
F
Pegler Yorkshire reserve the right to change specifications
5 Year Guarantee
Luxury Taps and Mixers
Pegler Yorkshire Customcare 5 Year Guarantee - Terms and Conditions
Product are subject to a 5 year guarantee that is between Pegler Yorkshire and the final purchaser of the
product.
The guarantee is subject to proof of purchase being supplied.
This guarantee does not affect any statutory rights the consumer may have in law.
The guarantee covers manufacturing or material defects and does not cover parts subject to normal wear
and tear.
Finishes other than chrome are covered for a period of 3 years only and the guarantee on the finish is
subject to the cleaning instructions being followed.
The guarantee is not applicable where the product is fitted contrary to the conditions in the fitting
instructions.
Abusive behaviour and accidental damage to the product are not covered by this guarantee.
The extent of this liability is limited to the cost of the replacement of the defective item and not to fitting or
consequential damages.
Description
Minimum
Operating
Pressure (bar)
Maximum Cold Working
Pressure (bar)
Maximum Hot
Working Pressure (bar)
893-2 Concealed
Shower
0.2 bar
10.0 bar at temperatures up to
85oC
Not Suitable for Maximum Hot Working
Pressure
Care
To maintain the surface finish, simply wipe occasionally with a mild detergent on a soft damp cloth. Dry,
using a soft cloth. Never use abrasive cleaners or chemical household cleaners and avoid contact with
concentrated bleach.
Maintenance
No regular maintenance is required for this product.
In case of complete replacement Pegler recommend service valves should be fitted to the supply inlets.
For any further help or replacement parts please contact the Service Support Team on 0800 1560050.
Regulations
It is important to ensure that the water supplies to your taps and mixers are connected in accordance with
the water regulations (WRAS) requirements and good plumbing practice.
If the water flow streams are separate all the way to the outlet of the fitting, then there is no requirement to fit
check valves to the cold and hot pipes even if the supply pressures are unbalanced.
It is recommended that in all new and refurbishment installations a thermostatic mixing valve should be
installed on the hot inlet supply. The thermostatic mixing valve is designed to prevent scalding when using
the hot water supply.
893-2
Spare
Key
Description
Code
Barcode
Date From
Date To
Price (£) ex
VAT
N/A
N/A
HK45 SELF CLOSING CARTRIDGE
850589
5013866061547
01/01/1998
To
Current
£61.54
N/A
ORS13 O RING SET DISCONTINUED
850587
5013866061523
01/01/1998
To
Current
£0.00
Spare
Key
Description
Code
Barcode
Date From
Date To
Price
(£) ex
VAT
5013866057168
01/01/1990
31/12/1997
£0.00
1
1
HDH24CP PUSH LEVER HANDLE ASBY HOT
CP - DISCONTINUED
Spare
Key
Description
815132
Code
Barcode
Date From
Date To
Price (£) ex
VAT
01/01/1990
31/12/1997
£0.00
2
2
Spare Key
S8 ALLEN SCREW DISCONTINUED
Description
815131
Code
5013866057151
Barcode
Date From
Date To
Price (£) ex VAT
01/01/1990
31/12/1997
£0.00
4
4
SP4 SPRING - DISCONTINUED
Spare
Key
Description
815134
5013866057182
Code
Barcode
Date From
Date To
Price (£) ex
VAT
01/01/1990
31/12/1997
£0.00
5
5
BP1 BACKPLATE DISCONTINUED
Spare
Key
Description
815136
5013866057199
Code
Barcode
Date From
Date To
Price (£)
ex VAT
5013866057205
01/01/1990
31/12/1997
£65.93
6
6
CNP3CP CONCEALING PLATE
CHROME
815137
Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF
Telephone: Phone +44 (0) 844 243 4400 Fax: +44 (0) 844 243 9870 Website: www.pegleryorkshire.co.uk
Registered office : Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Company no : 00401507
Your Guide to the Installation,
Care and maintenance of
PERFORMA
Self Closing Shower
& Bib Valves
893-2 Concealed Shower Valve – 344010
890-2 Exposed Shower Valve – 344007
883-2 Exposed Bib Tap – 347006
Pegler Limited, St Catherine’s Avenue, Doncaster DN4 8DF
Telephone 01302 560560, Fax 01302 560109
Pegler Yorkshire Technical Office, Tel 0870 1200285
Before installing this product – Pegler recommend the reading of this document
thoroughly and leaving it with the user for future reference.
Introduction
The PERFORMA 890-2, 893-2 and and/or 883-2 self closing non concussive shower valves
and bib taps use a limescale resistance cartridge which gives many years of trouble free
service. The piston operated cartridge controls the flow of water from a minimum of 0.2 bar
to a maximum 3.0 bar. Should you have any problems or technical queries with either of
these products please telephone 0870 1200285, or fax us on 01302 560537.
Water Regulations Requirements
It is important to ensure that the water supplies to your taps and mixers are connected in
accordance with the water regulations (WRAS) requirements and good plumbing practice.
This products has been designed to function on all types of water systems
Please Note: If a pump is to be installed to boost gravity supplies please refer to the pump
manufactures instructions.
Pipe Connections
IMPORTANT. Before making any inlet pipe connections all supplies MUST be thoroughly
flushed to remove any debris. Failure to do so could result in damage or low flow from
the valves. It is a requirement of Byelaw 55 of the Water Fittings Byelaw Scheme that this
function is undertaken before making any pipe connections to supplies. It is also Pegler’s
recommendation and good plumbing practice that a service valve also (Pegler PB300)
should be installed upstream in the inlet supply lines and appropriate filters inline before the
terminal fitting.
All valves are supplied with ½” BSP inlet and outlet and complete with nuts and olives.
To reduce pressure to the optimum level we also recommend the use of a Pegler Pressure
Reducing Valve. For use on pressures between 1.1/2 bar to 5.1/2 bar - product code 5A2001
for ½” pipe or 5A2002 for ¾” pipe.
General Installation Notes
• Care must be taken during installation to prevent any risk of damage to the product or
injury to installer.
• Installation must be carried out by a qualified and competent person and in accordance
with the instructions supplied.
• Installations must comply with all Local and National Water Authority Regulations, and
Building/Plumbing Regulations.
• Please ensure that you have read and understood all sections of this manual before
installation.
• Please ensure no soldering occurs near the tap. Any soldering required should be done
before the valve is installed as any heat generated can damage the cartridge and seals.
• It is also Pegler Yorkshire’s recommendations that in-line filters are installed to the valves.
Isolation valves near to the valves are also recommended to allow individual isolation for
servicing and maintenance.
Please ensure that you have read and understood all sections of this manual before installation
Please ensure no soldering occurs near the tap. Any soldering required should be done before
installed
as any heat
can damage the cartridge and seals.
Conditions
for generated
normal use
It is also Pegler Yorkshire’s recommendations that in-line filters are installed to the valves. Isola
near to the valves are also recommended to allow individual isolation for servicing and mainten
Maximum Static Pressure (bar)
Flow
ions for normal
usePressure – hot and cold sides (bar)
Maximum Temperature Range
3.0 bar
0.2 bar
60 degrees C
Maximum Static Pressure (bar)
3.0 bar
Pressure
hot and
cold sides
(bar) device should0.1
Please note: Flow
a suitable
hot –
water
temperature
control
be bar
installed to
Maximum
Temperature
Range
60
degrees
C hot
reduce temperatures that exceed any safe hot water temperature, or the maximum
water supply temperature stated above. This can easily be achieved by installing upstream
note: a suitable hot water temperature control device should be installed to reduce temperature
of the terminal fitting either single point or group mixing valves which can achieve a more
ove maximum hot water supply temperature. This can easily be achieved by installing upstream o
suitablewhich
temperature.
An example
the Pegler
Yorkshire’s
approvedPlease
Prestexsee
410the
Group
mixing valves
can achieve
a moreissuitable
shower
temperature.
Pegler Yo
Mixing
Valve
22mm
size –Valve
product
code size
5A1060.
ed Prestex
410
Group
Mixing
22mm
– product code 5A1060.
note: Please
Ensure note:
that the
flow that
ratethe
through
any
mixing
valve
used
is used
sufficient
to supply
enough wa
Ensure
flow rate
through
any
mixing
valve
is sufficient
to supply
enough water to each valve.
Pressure (bar)
0.1
0.2
0.3
0.4
0.5
1.0
2.0
3.0
4.0
(l/m)
17
26
32.5
39
44
63
89
109
125
Pre-Installation Checks
• Ensure that there is sufficient space to install the product without hampering its
operation.
• Ensure all pipe work has been thoroughly flushed before any installation takes place.
Installation of Exposed Shower Valve 890-2
1. Determine the position of the shower valve allowing sufficient height for any riser pipe or
spray head options.
2. Route supply pipework to shower valve, flush pipework thoroughly.
3. Offer shower valve complete with assembled flange to the wall and mark location on
screw holes.
4. Drill wall and fix wall plugs.
Please Note: For best fixing results please try and ensure that suitable depth for screwing
is allowed. Using wooden framework for studded wall is suitable.
5. Screw shower valve to wall – Ensuring that the valve body is correctly positioned (arrows
stamped on the body show direction of flow) the inlet supply is the bottom connection.
If fitted incorrectly the self closing action will not operate correctly.
6. Connect supply pipework and depress the button for 2-3 minutes clear away any
remaining debris in the pipework.
Please Note: For ease of checking and disassembly if needed the test here is done
without any shower head or riser pipe fitted. To help control the water when testing a spare
shower hose screwed to the outlet will control the direction of water flow.
7. Depress button once more and check time/delay, flow and self closing action is
functioning correctly. See time adjustment and flow adjustment sections for
detail on how to change the factory set positions.
8. Connect shower head and riser pipe.
Installation of Concealed Shower Valve 893-2
1. The concealed shower valve has a built in depth adjustment of 14mm (see dimensional
drawing) From back of the valve to finished wall surface the dimensions 50mm to
maximum 66mm. Please adhere to these critical dimensions.
2. Determine the position of the shower valve.
3. Route supply pipework to shower valve, flush pipework thoroughly.
4. Position shower valve in the desired position and ensure that appropriate pipework can
be positioned from shower valve to shower head.
5. Pipework should be firmly clamped to the wall near the valve prevent movement of valve
when operated.
6. Fit the shower valve to wall – Ensuring that the valve body is correctly positioned (arrows
stamped on the body show direction of flow) the inlet supply is the bottom connection.
If fitted incorrectly the self closing action will not operate correctly.
7. Connect supply pipework and depress the button for 2-3 minutes clear away any
remaining debris in the pipework.
Please Note: For ease of checking and disassembly if needed the test here is done
without any shower head or riser pipe fitted. To help control the water when testing a spare
shower hose screwed to the outlet will control the direction of water flow.
8. Depress button once more and check time/delay, flow and self closing action is
functioning correctly. See time adjustment and flow adjustment sections for
detail on how to change the factory set positions.
9. Make good the wall surface ensuring that the built in depth dimensions are adhered to.
10.Place chrome flange over push button shower valve and push back until it meets with
the finished wall surface. For a complete watertight seal run a bead of clear silicon sealant
around the underside of the flange.
11.Connect shower head to exposed shower arm.
Installation of Bib Tap 883-2
1. Determine the position of the exposed bib tap.
2. Route supply pipework to shower valve, flush pipework thoroughly.
3. Offer the complete bib tap with assembled flange to the wall and mark location on screw
holes.
4. Drill wall and fix wall plugs.
Please Note: For best fixing results please try and ensure that suitable depth for screwing
is allowed. Using wooden framework for studded wall is suitable.
5. Screw bib tap to wall
6. Connect supply pipework and depress the button for 2-3 minutes clear away any
remaining debris in the pipework.
7. Depress button once more and check time/delay, flow and self closing action is functioning
correctly. See time adjustment and flow adjustment sections for detail on
how to change the factory set positions.
8. Make good the wall surface ensuring that the built in depth dimensions are adhered to.
Time Adjustment: If the time delay factory set is not acceptable then it can be can be
adjusted to a maximum 22 seconds. First locate the time variable control hole at the side
of the indice hole on the front handle and with the use of the Allen key provided locate
internally the time delay screw. Adjustment of the time delay is done easily by simply rotating
clockwise to decreases the time and rotating anti-clockwise to increases the time.
Flow Adjustment: The Pegler Yorkshire collection of self closing shower valves also offer
adjustable flow control to be used in conjunction with the variable time delay feature.
The adjustment is made by carefully unscrewing the head of the valve (locate carefully
spanner on hexagon below push handle and unscrew – being careful not to damage
the chrome finish) Once unscrewed you will notice 4 slotted windows around the plastic
cartridge. By pulling the plastic cartridge away from the valve head it can be re positioned at
in further 4 separate locations each 90 degrees from its previous position.
Once the correct position has been reached then the cartridge can be positioned back
into the brass shower valve body. Located and then retighten using spanner being careful
not to damage the chrome finish on the hexagon once more.
Please Note: The valve head should not be over tightened as this can damage the plastic
cartridge inside.
Care & Maintenance
To maintain the surface finishes, simply wipe occasionally with a mild detergent on soft
damp cloth. Dry using soft cloth, never use abrasive cleaners or chemical household
cleaners, avoid contact with concentrated bleach.
Pegler products are manufactured to the highest standards and should require little or
no maintenance. In the unlikely event of any spare part requirements, please visit our
website: www.pegler.co.uk, contact you’re nearest stockist or the Pegler Technical Office
on telephone 0870 1200285.
Pegler Limited, St Catherine’s Avenue, Doncaster DN4 8DF
Telephone 01302 560560, Fax 01302 560109
Pegler Yorkshire Technical Office, Tel 0870 1200285