PN 2005993 - Ag Leader Technology

advertisement
Ag Leader Technology
SeedCommand
Implement switch – Kinze row unit
NOTE: Indented items indicate parts included
in an assembly listed above
Part Name/Description
Part Number
Quantity
4100830
1
Hex head capscrew – 3/8 in. x 1-1/2 in
Hex nut – 3/8 in.
Flat washer - #8
Split lockwasher – 3/8 in.
Hex nylock nut – 4 mm
2002001-38150
2002051-38
2002071-08
2002061-38
2002155-04
2
2
2
2
2
Phillips pan head screw – 4mm x 25 mm
Installation instructions – Implement switch, Kinze row unit
2002437-04025
2005993
2
1
4001507
4002461
1
1
Implement Switch Installation Kit – Kinze Row Unit
Switch – Implement
Bracket – Implement switch mounting – Kinze row unit
PN: 2005993
February 2011 – Rev A
1
Ag Leader Technology
Important
Notices
SeedCommand
Implement switch – Kinze row unit
Please carefully follow these step-by-step instructions. If you have questions,
contact Ag Leader Technology at 515-232-5363 x 1.
Direction words (LEFT and RIGHT) are commonly used when describing an
installation procedure. Interpret direction words as if standing behind equipment
facing forward.
Signal words (DANGER, WARNING, CAUTION and NOTE) are provided to
draw attention to information that is important for the safe/correct installation and
operation of this product.
Section
Contents
PN: 2005993

– Indicates an imminently hazardous situation that, if not
avoided, will result in serious injury or death.

– Indicates a potentially hazardous situation that, if not avoided,
could result in serious injury or death.

– Indicates a potentially hazardous situation that, if not avoided,
may result in minor or moderate injury.

CAUTION – Indicates practices that may result in property damage, but do not
involve personal injury.

NOTE – The preferred signal word to address practices not involving property
damage, or personal injury.
Item
Installing implement switch onto bracket
Installing bracket and switch onto row unit
Page
3
4
February 2011 – Rev A
2
Ag Leader Technology
SeedCommand
Implement switch – Kinze row unit
Installing
implement
switch onto
bracket
Required Parts:
(2) Flat washer - #8 ---------------------------------------------------(2) Hex nylock nut – 4 mm -------------------------------------------(2) Phillips pan head screw – 4mm x 25mm -----------------------(1) Switch – Implement ------------------------------------------------(1) Bracket – Implement switch mounting – Kinze ----------------
Part Number:
2002071-08
2002155-04
2002437-04025
4001507
4002461
Step-by-Step
Procedure
1. Install one (1) 4mm x 25mm Phillips pan head screw thru each hole in
Implement switch
2. Place screws thru holes in implement switch bracket. Install one (1) #8 washer
and one (1) 4mm locknut onto each bolt from inside of implement switch
bracket. Tighten both locknuts while holding implement switch in the center of
the slotted cutout. Assembled switch and bracket is shown in Figure 1.
Figure 1: Implement switch installed on bracket
PN: 2005993
February 2011 – Rev A
3
Ag Leader Technology
Installing
bracket and
switch onto row
unit
Step-by-step
Procedure
SeedCommand
Implement switch – Kinze row unit
Required Parts:
(2) Hex head capscrew – 3/8 in. x 1-1/2in. ---------------------(2) Hex nut – 3/8 in. ------------------------------------------------(2) Split lockwashers – 3/8 in. -------------------------------------
1.
Part Number:
2002001-38150
2002051-38
2002061-38
Lower toolbar so entire weight of row unit is supported by the ground. Remove
bolts, shown in Figure 2, that attach planter stop to row unit.
Figure 2: Row unit stop and bolts
2. Install one (1) 3/8 in x 1-1/2 bolt in upper bolt hole in the implement switch
bracket
3. Reinstall the 3/8 in x 1-1/2 bolt in the upper hole of the planter row unit from
inside of row unit.
4. Install row unit stop onto the 3/8 x 1-1/2 bolt from outside of row unit.
5. Put one (1) 3/8 in split lockwasher and one (1) 3/8 in nut onto the bolt.
6.
PN: 2005993
Install one (1) 3/8 in x 1-1/2 in bolt thru lower bolt hole of row unit stop from
outside of row unit. Install one (1) 3/8 in split lockwasher and one (1) 3/8 in nut
onto bolt. Tighten both nuts.
February 2011 – Rev A
4
Ag Leader Technology
SeedCommand
Implement switch – Kinze row unit
Figure 3: Implement switch installed
7. Raise toolbar so row unit is in lowered position. Switch should trip on row unit
crossbar. Adjust switch if necessary.
Revision History
Date
Feb 2011
PN: 2005993
Revision
A
Initials
TGI
Changes
-
Initial Release
February 2011 – Rev A
5
Download