INSTALLATION
S M 5 1 6
INSTRUCTIONS
P R O M M E R C I A L
®
S P E A K E R
Step 4
Connect the wire from your amplifier to the terminals on the back of the
speaker. Double check the polarity of the speaker wires, amplifier + to
speaker + and amplifier – to speaker –.
INTRODUCTION
The Sound Advance Prommercial SM516 is designed for a wide range
of indoor and outdoor commercial applications. When properly
installed, this product will provide years of high quality sound
reproduction.
To obtain the full potential of this Sound Advance speaker, please read
all instructions before starting the installation.
PARTS LIST
Each Sound Advance SM516 speaker package includes the following items:
(2) Sound Advance SM516 speakers
Once the wires are connected you can set the rotary switch located on
the back of the speaker to the appropriate output level.
The combined wattage requirements of the speakers should not exceed
80% of the amplifiers rated output. Following this rule will increase the
reliability of your installation.
Here is an example:
A system uses 24 SM516 speakers set on their 2-watt taps.
24 speakers x 2-watt tap = 48 watts
48 watts / .80 = 60 watts (use this size amplifier)
Transformer Tap Switch
70 volt - 16W, 8W, 4W and 2W
100 volt - 16W, 8W, 4W and 2W
8 Ohm
(4) Bracket knobs
(2) C-shaped mounting brackets
INSTALLING THE SPEAKERS
SM516
Step 1
Remove the speakers from the shipping
carton. Loosen the two knobs on each
speaker and remove the brackets.
Step 2
Run wire from your amplifier to the
speaker locations.
Typical wire gauge and lengths used in 70
volt systems:
18
18
18
18
gauge
gauge
gauge
gauge
x
x
x
x
SM516
10 watt load = 2200 feet
20 watt load = 1100 feet
50 watt load = 550 feet
100 watt load = 275 feet
Note: When using the speakers in an 8ohm system use the Wire Gauge Chart on
page 2 as a reference.
Step 3
Mount the C-brackets to the wall surface.
The holes in the brackets are 5-7/8" apart
center-to-center. Use the included stainless
steel screws if you are mounting the
speakers outdoors. Run the speaker wires
through the wire holes in the C-brackets.
Step 5
Install the speaker onto the bracket. Screw
the bracket knobs into the cabinet. Point
the speaker towards the listening area.
Once the angle of the speaker has been
determined tighten the bracket knobs
securely.
WIRE GAUGE AND QUALITY
When using the SM516 in an 8-ohm system the total wire resistance
should be less than 10% of the speaker impedance. The SM516
speaker is nominally an 8-ohm speaker, so your total wire resistance
should be no more than 0.8 ohms.
9.375"
In simple terms, the extra resistance from the wire will have a very
negative affect on the sound quality of the speaker. The sound can be
less dynamic, definition of bass frequencies can be reduced, and in
extreme cases, the high frequencies can be attenuated. Amplifier
power is also wasted in the wire, reducing the maximum output level
of the system.
Please refer to the following chart when deciding on the appropriate
wire gauge for your installation.
Wire resistance in Ohms vs. length of cable run
Distance in Feet
50' 100' 150' 200' 250' 300'
20 gauge
.86
1.73
2.59
3.45
4.32
5.18
18 gauge
.65
1.30
1.94
2.59
3.24
3.89
16 gauge
.43
.85
1.28
1.71
2.14
2.56
14 gauge
.27
.54
.81
1.08
1.35
1.62
12 gauge
.17
.34
.51
.68
.85
1.02
10 gauge
.11
.22
.33
.44
.56
.67
6.125"
4.500"
PAINTING THE SPEAKERS AND GRILLES
Sound Advance SM516 speakers feature a tough, weather-resistant
ABS finish that may be painted to color match your surroundings. Use
a weather resistant outdoor paint and a spray gun. First remove the
gril le by carefully prying it aw ay from the baffle. The driver
components must be protected from paint when spraying. Place the
grille on a piece of cardboard and trace around the outside of the
grille. Cut just inside the line you drew on the cardboard and place the
paint plug on the speaker baffle. Remove the paint plug when you are
finished painting.
6.500"
The metal grilles may also be painted. Use very thin paint (5:1). It will
be easier to paint the grille while it is off the speaker. Avoid plugging
up the holes with excess paint.
1.750"
3.920"
8.625"
9.375"
5.875"
Polar Response Horizontal 125 to 1k
Polar Response Horizontal 2k to 16k
Curve
dBSPL
Freq
90
100
BW
125.00
359
Q
DI
1.0
0.0
100
359
1.0
0.0
90
80
500.00
359
1.0
0.0
80
70
1.00K
173
2.1
3.2
70
90
120
250.00
60
120
150
30
150
40
30
30
20
20
BW
Q
DI
100
3.6
5.5
4.00K
86
4.2
6.2
8.00K
91
3.9
6.0
16.00K
52
6.9
8.4
Freq
BW
30
10
10
0
0
-10
-10
0
Deg
180
-180
-20
-10
-10
180
-180
0 Deg
0
0
10
10
20
20
30
30
40
-150
50
40
-30
-150
50
-30
60
60
70
70
80
80
-120
90
-60
100
-120
90
dBSPL
90
-90
Polar Response Vertical 2k to 16k
Freq
BW
Q
DI
100
125.00
359
1.0
0.0
90
80
250.00
359
1.0
0.0
80
70
500.00
359
1.0
0.0
60
1.00k
136
2.7
4.2
90
-60
100
-90
Polar Response Vertical 125 to 1k
Curve
120
60
50
dBSPL
90
Curve
Q
95
3.8
5.8
71
5.1
7.0
70
8.00k
72
5.0
7.0
60
16.00k
57
6.3
8.0
60
150
40
30
30
20
20
30
10
10
0
0
-10
-10
180
-180
-20
0 Deg
-10
-10
0
0
10
10
20
20
30
180
-180
0 Deg
30
40
-150
50
40
-30
-150
50
60
-30
60
70
70
80
80
-120
90
-60
100
90
-120
90
-90
Impedance
Ohm
-60
100
-90
100
On Axis SPL
dBSPL
90
50
80
70
20
60
50
10
40
30
5
20
10
2
0
-10
1
20 Hz
50
100
200
500
1k
2k
5k
10k
20K
DI
2.00k
4.00k
120
50
30
150
40
-20
60
Freq
2.00K
50
50
40
100
Curve
90
60
60
-20
dBSPL
-20
20Hz
50
100
200
500
1k
2k
5k
10k
20k
TECHNICAL ASSISTANCE AND SERVICE
The Technical Assistance Department at Sound Advance is available at (800)
592-4644 or (949) 492-5449 to answer any questions concerning the operation
and installation of your speakers between the hours of 7:00 AM and 5:00 PM
Pacific time, Monday through Friday, except holidays.
SOUND ADVANCE PROMMERCIAL SM516
In the event your unit should need repair or service, you may return the unit to
your authorized dealer or use the following guidelines:
1. Be prepared to state the model number and / or serial number, date of
purchase and dealer's name and address when calling.
Tweeter
5/8" (16mm) Polycarbonate dome
Woofer
5-1/4" (133mm) Polypropylene cone with a
rubber surround
Frequency Range
65Hz – 20kHz ±10dB
Nominal Sensitivity
88dB 1w/1m
3. If you are returning the product directly to Sound Advance, call us to obtain a
return authorization number before shipping.
Nominal Coverage angle
90.0 degrees vertical
90.0 degrees horizontal
YOU MUST HAVE PRIOR AUTHORIZATION TO RETURN YOUR UNIT.
Directivity Factor
2.94 averaged from 500 Hz to 4 kHz
Directivity Index
3.50 averaged from 500 Hz to 4 kHz
4. The original packaging must be used. If the original packaging is unavailable,
replacements can be obtained from Sound Advance for a small fee.
Transformer Taps
70 volt - 16W, 8W, 4W and 2W
100 volt - 16W, 8W, 4W and 2W
8 Ohm
5. Ship the product via United Parcel Service, Federal Express, or other package
delivery service. Please do not use the U.S.Postal Service.
Power Capacity
60 watts maximum program power
40 watts continuous Pink noise
6. Write the return authorization number on the outside of the box.
Enclosure
Enclosure: ABS meets UL94V-0 fire rating
Baffle: ABS meets UL94V-0 fire rating
Grille
Paintable weather resistant aluminum
Termination
4-Post barrier strip
Speaker Dimensions
6-1/8" (156mm) x 9-3/8" (238mm) x 6-1/2" (165mm)
Product Weight
8.0 lbs (3.63 kg) each
Shipping Weight
19.0 lbs (8.61 kg) per pair
Included Accessories
C - Bracket
Available Colors:
Black (SM516K; White (SM516W)
2. Contact Sound Advance directly at (800) 592-4644 or (949) 492-5449 or at
www.soundadvance.com
7. Ship to:
8.
ARCHITECTURAL SPECIFICATIONS
The loudspeaker shall be of the two-way type comprising a single
surface mount enclosure containing one 5-1/4" (133mm) low
frequency transducer and one 5/8" (16mm) high frequency transducer.
Frequency response shall be 65 – 20000Hz. Total power handling shall
be 40 watts RMS and 60 watts program. Sensitivity measured with
2.83 volts input at 1 meter on axis averaged between 65 – 20000Hz
shall be 88dB. The unit shall be supplied with a line matching
transformer suitable for 100 volt or 70 volt with a rear mounted control
allowing user selectable power taps of 16W, 8W, 4W, 2W and a 8 ohm
bypass.
Attn: Quality Assurance Department
Sound Advance
212 Avenida Fabricante
San Clemente, CA 92672-7531
FREIGHT COLLECT SHIPMENTS WILL BE REFUSED!
WARRANTY, REMEDY, EXCLUSIONS AND
L I M I T A T I O N S
( U S A O N L Y )
Limited Warranty:
Sound Advance warrants this product to the original purchaser to be free from
defects in material and workmanship, under normal use and conditions, for a
period of five (5) years from the date of original purchase as shown on the
invoice.
The foregoing exclusive warranty gives you specific legal rights, and you may
have other rights, which vary from state to state. This warranty applies
exclusively to the original purchaser.
The exclusive warranty does not apply and is ineffective if:
1. The invoice fails to establish that the product was purchased from an
authorized Sound Advance dealer or distributor;
2. The product was subjected to misuse, neglect, accident, or improper
installation. [Damage to the product was caused by accident, abuse, or
misuse];
3. The product was modified, altered, or repaired by unauthorized personnel; or
The enclosure and baffle shall be injection molded using fire rated ABS
that meets UL94V-0. Wire shall be terminated on the rear of the
enclosure.
The system shall include a powder coated aluminum C-bracket for
mounting the speaker.
External dimensions shall be 6-1/8" (156mm) width x 9-3/8" (238mm)
height x 6-1/2" (165mm) depth. Each enclosure with mounting bracket
shall weigh 8 lbs. (3.63 kg) per unit.
The loudspeaker shall be the Sound Advance Prommercial SM516K
(black) or SM516W (white). No other system shall be acceptable
unless the above combined performance specifications are equaled or
exceeded.
w w w . s o u n d a d v a n c e . c o m
4. The unit was not used as described in the installation and operating
instructions.
Exclusive Remedy:
Sound Advance agrees, at its option during the five (5) year warranty period, to
repair any defect in material or workmanship or to furnish an equal product in
exchange without charge to the purchaser, subject to verification of the defect
and proof of the date of purchase.
Warranty Exclusions and Damage Limitations
The exclusive warranty set forth above is in lieu of all other warranties, express
or implied, including without limitation the implied warranties of merchantability
and fitness for a particular purpose, which are expressly disclaimed. In no event,
and under no circumstances or legal or equitable theory, shall Sound Advance be
liable or responsible for any direct or indirect damages, consequential damages,
loss, or injury, including without limitation, personal injury, bodily injury,
property damage, emotional distress, death, real property or personal property
damage, business interruption, costs of delay or lost profits arising from the
product, whether based upon warranty, contract, negligence, strict product
liability or other theory.
So un d Ad v anc e • 2 1 2 Av eni d a Fa b ri ca nt e • San Cl em ent e, C A 9 2 6 7 2- 7 5 3 1 , U SA • (8 0 0 ) 5 9 2 -4 6 4 4 o r (9 4 9 ) 4 9 2 -5 4 4 9 • FA X : ( 9 4 9 ) 3 6 1- 5 1 5 1
©2006 Sound Advance.
Sound Advance, Prommercial and RotoLock are registered trademarks of Dana Innovations.
33-4190
03/06