HP Switch Software
Comware CLI Commands in ProVision Software
K/KA.15.13
Abstract
This switch software guide is intended for network administrators and support personnel, and applies to the switch models
listed on this page unless otherwise noted. This guide does not provide information about upgrading or replacing switch
hardware. The information in this guide is subject to change without notice.
Applicable Products
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
2615 Switches (J9565A)
2620 Switches (J9623A, J9624A, J9625A, J9626A, J9627A)
2910al Switches (J9145A, J9146A, J9147A, J9148A)
2915 Switches (J9562A)
2920 Switches (J9726A, J9727A, J9728A, J9729A)
3500 Switches (J9470A, J9471A, J9472A, J9473A)
3500yl Switches (J8692A, J8693A)
3800 Switches (J9573A, J9574A, J9575A, J9576A, J9584A, J9585A, J9586A, J9587A, J9588A)
5400zl Switches (J8697A, J8698A, J9447A, J9448A)
6200yl Switch (J8992A)
8200zl Switches (J9475A, J8715A/B )
6600 Switches (J9263A, J9264A, J9265A, J9451A, J9452A)
HP Part Number: 5998-4399
Published: June 2013
Edition: 2
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. All Rights
Reserved.
This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or
translated into another language without the prior written consent of Hewlett-Packard.
Publication Number
5998-4399
June 2013
Applicable Products
Trademark Credits
Microsoft, Windows, and Microsoft Windows NT are US registered trademarks of Microsoft Corporation. Java™ is a US trademark of Sun
Microsystems, Inc.
Disclaimer
The information contained in this document is subject to change without notice.
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors
contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained
herein.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.
Software End User License Agreement and Hardware Limited Warranty
For the software end user license agreement and the hardware limited warranty information for HP Networking products, visit www.hp.com/
networking/support.
Contents
Product Documentation.................................................................................13
About Your Switch Manual Set.................................................................................................13
Electronic Publications........................................................................................................13
1 Introduction To the ProVision CLI.................................................................14
Comware Command Support in ProVision Software....................................................................14
Listing Display Commands in the CLI.........................................................................................14
CLI Operation........................................................................................................................16
Comparing Comware and ProVision Commands....................................................................16
Output Differences Between Display and Show commands.................................................16
DNS Field Mappings................................................................................................16
Using CLI Context Levels.....................................................................................................16
Empty Output....................................................................................................................17
Further CLI Operating Information........................................................................................17
2 Display Commands..................................................................................18
display acl <acl-number> | name <acl-name>>.........................................................................18
Field Descriptions...............................................................................................................18
Operating Notes...............................................................................................................18
display arp............................................................................................................................19
Field Descriptions...............................................................................................................19
Operating Notes...............................................................................................................19
display arp <ip-address>.........................................................................................................21
Field Descriptions...............................................................................................................21
Operating Notes...............................................................................................................21
display arp detection..............................................................................................................22
display arp detection statistics..................................................................................................23
display arp ip-address.............................................................................................................24
Operating Notes...............................................................................................................24
display boot-loader.................................................................................................................25
Field Descriptions...............................................................................................................25
Operating Notes...............................................................................................................25
display clock..........................................................................................................................27
Field Descriptions:..............................................................................................................27
Operating Notes...............................................................................................................27
display command-alias............................................................................................................28
Field Descriptions...............................................................................................................28
Operating Notes...............................................................................................................28
display counters.....................................................................................................................29
Field Descriptions...............................................................................................................29
Operating Notes...............................................................................................................29
display counters rate...............................................................................................................31
Operating Notes...............................................................................................................31
display cpu-usage...................................................................................................................32
Operating Notes...............................................................................................................32
display cpu-usage history........................................................................................................33
display current-configuration....................................................................................................34
display current-configuration by-linenum.....................................................................................35
display current-configuration configuration.................................................................................36
display current-configuration interface.......................................................................................37
display debugging.................................................................................................................39
Operating Notes...............................................................................................................39
Contents
3
display default-configuration....................................................................................................41
display device........................................................................................................................42
Field Descriptions...............................................................................................................42
display dhcp relay information all.............................................................................................43
display dhcp relay information interface Vlan-interface <vlan-id>..................................................44
display dhcp relay statistics......................................................................................................45
Field Descriptions...............................................................................................................46
Operating Notes...............................................................................................................47
display dhcp-snooping [ip ip_address]......................................................................................49
display dhcp-snooping binding database..................................................................................50
display dhcp-snooping information...........................................................................................51
Operating Notes...............................................................................................................51
display dhcp-snooping packet statistics......................................................................................52
display dhcp-snooping trust......................................................................................................53
Field Descriptions...............................................................................................................53
Operating Notes...............................................................................................................53
display diagnostic-information..................................................................................................54
display dns < domain | server >..............................................................................................55
Field Descriptions...............................................................................................................55
Operating Notes...............................................................................................................55
display dns domain................................................................................................................57
Operating Notes...............................................................................................................57
display dns domain dynamic...................................................................................................58
display dns ipv6 server...........................................................................................................59
Field Descriptions...............................................................................................................59
Operating Notes...............................................................................................................59
display dot1x [interface …]display dot1x sessions [interface …]display dot1x statistics [interface
…].......................................................................................................................................61
Operating Notes...............................................................................................................63
display dot1x [interface]..........................................................................................................64
Field Descriptions...............................................................................................................67
Operating Notes...............................................................................................................68
display environment................................................................................................................72
Field Descriptions...............................................................................................................72
display fan............................................................................................................................73
Operating Notes...............................................................................................................73
display fib <ip-address>..........................................................................................................74
Field Descriptions...............................................................................................................74
Operating Notes...............................................................................................................74
display fips status...................................................................................................................76
display garp statistics interface <port_list>.................................................................................77
display garp timer interface <port_list>.....................................................................................78
Operating Notes...............................................................................................................78
display gvrp state interface <port_list> vlan <vlan-id>.................................................................79
Field Descriptions...............................................................................................................79
display gvrp statistics..............................................................................................................80
Field Descriptions...............................................................................................................80
display gvrp status..................................................................................................................81
Operating Notes...............................................................................................................81
display gvrp vlan-operation interface interface-type interface-number.............................................82
display history-command.........................................................................................................83
Operating Notes...............................................................................................................83
display hwtacacs....................................................................................................................84
Operating Notes...............................................................................................................85
display igmp group.................................................................................................................86
4
Contents
Field Descriptions...............................................................................................................86
Operating Notes...............................................................................................................86
display igmp group interface vlan-interface <vid>.......................................................................87
Field Descriptions...............................................................................................................87
Operating Notes...............................................................................................................87
display igmp group interface vlan-interface <vlan-id> static..........................................................88
Field Descriptions...............................................................................................................88
display igmp group interface vlan-interface <vlan-id> verbose......................................................89
display igmp group port-info....................................................................................................90
Field Descriptions...............................................................................................................90
Operating Notes...............................................................................................................91
display igmp group static........................................................................................................92
Field Descriptions...............................................................................................................92
display igmp group verbose.....................................................................................................93
display igmp group x.x.x.x static..............................................................................................94
Field Descriptions...............................................................................................................94
display igmp group x.x.x.x verbose...........................................................................................95
display igmp interface.............................................................................................................96
Field Descriptions...............................................................................................................96
Operating Notes...............................................................................................................97
display igmp interface verbose.................................................................................................98
display igmp interface vlan-interface <vlan-id>...........................................................................99
Field Descriptions...............................................................................................................99
Operating Notes...............................................................................................................99
display igmp routing-table.....................................................................................................101
Field Descriptions.............................................................................................................101
display interface...................................................................................................................102
Operating Notes.............................................................................................................103
display interface brief...........................................................................................................104
Field Descriptions.............................................................................................................104
Operating Notes.............................................................................................................105
display interface brief down...................................................................................................106
Field Descriptions.............................................................................................................106
Operating Notes.............................................................................................................106
display ip as-path.................................................................................................................108
Field Descriptions.............................................................................................................108
Operating Notes.............................................................................................................108
display ip check source.........................................................................................................109
Field Descriptions.............................................................................................................109
Operating Notes.............................................................................................................109
display ip community-list........................................................................................................111
Field Descriptions.............................................................................................................111
Operating Notes.............................................................................................................111
display ip http......................................................................................................................112
display ip https.....................................................................................................................113
display ip ip-prefix................................................................................................................114
Operating Notes.............................................................................................................114
display ipv6 dhcp duid.........................................................................................................115
Field Descriptions.............................................................................................................115
Operating Notes.............................................................................................................115
display ipv6 dhcp relay server-address all................................................................................116
Field Descriptions.............................................................................................................116
Operating Notes.............................................................................................................116
display ipv6 dhcp relay server-address interface <id>...............................................................117
Field Descriptions.............................................................................................................117
Contents
5
Operating Notes.............................................................................................................117
display ipv6 dhcp relay statistics.............................................................................................118
Field Descriptions.............................................................................................................118
Operating Notes.............................................................................................................119
display ipv6 fib....................................................................................................................120
Field Descriptions.............................................................................................................120
Operating Notes.............................................................................................................120
display ipv6 fib <ip-address>.................................................................................................122
Field Descriptions.............................................................................................................122
Operating Notes.............................................................................................................122
display ipv6 neighbors all.....................................................................................................124
Field Descriptions.............................................................................................................124
Operating Notes.............................................................................................................124
display ipv6 routing-table......................................................................................................126
Operating Notes.............................................................................................................127
display ipv6 routing-table ipv6-address...................................................................................128
Operating Notes.............................................................................................................128
display ipv6 routing-table protocol..........................................................................................130
Operating Notes.............................................................................................................130
display lacp system-id...........................................................................................................131
Field Descriptions.............................................................................................................131
Operating Notes.............................................................................................................131
display link-aggregation........................................................................................................133
Operating Notes.............................................................................................................133
display link-aggregation member-port......................................................................................134
Field Descriptions.............................................................................................................134
display link-aggregation summary...........................................................................................136
Field Descriptions.............................................................................................................136
display link-aggregation verbose............................................................................................137
Field Descriptions.............................................................................................................137
display lldp local-information.................................................................................................139
display lldp local-information global.......................................................................................141
display lldp local-information interface interface-type interface-number........................................142
display lldp neighbor-information brief....................................................................................143
display lldp neighbor-information list display lldp neighbor-information list system-name <string>.....144
display lldp statistics.............................................................................................................145
display lldp statistics global...................................................................................................146
display lldp statistics interface interface-type interface-number....................................................147
display lldp status.................................................................................................................148
display lldp status interface interface-type interface number........................................................149
display lldp tlv-config interface interface-type interface-number...................................................150
display local-proxy-arp..........................................................................................................151
Operating Notes.............................................................................................................151
display logfile buffer.............................................................................................................152
Operating Notes.............................................................................................................153
display loopback-detection.....................................................................................................154
Field Descriptions.............................................................................................................154
display mac-address..............................................................................................................155
Operating Notes.............................................................................................................155
display mac-address aging-time..............................................................................................156
Field Descriptions.............................................................................................................156
Operating Notes.............................................................................................................156
display mac-address multicast.................................................................................................157
display mac-authentication.....................................................................................................158
Field Descriptions.............................................................................................................158
6
Contents
Operating Notes.............................................................................................................159
display mac-authentication [interface …]..................................................................................161
Operating Notes.............................................................................................................162
display memory....................................................................................................................163
Field Descriptions.............................................................................................................163
Operating Notes.............................................................................................................163
display mld group................................................................................................................164
Field Descriptions.............................................................................................................164
Operating Notes.............................................................................................................164
display mld group interface vlan-interface <vid>.......................................................................166
Field Descriptions.............................................................................................................166
display mld group interface vlan-interface <vid> verbose...........................................................167
Field Descriptions.............................................................................................................167
display mld group port-info vlan <vlan-id> display mld group port-info........................................169
display mld group verbose.....................................................................................................170
Field Descriptions.............................................................................................................170
display mld group x:x::x:x.....................................................................................................172
Field Descriptions.............................................................................................................172
display mld group x:x::x:x verbose.........................................................................................173
Field Descriptions.............................................................................................................173
display mld interface.............................................................................................................174
Field Descriptions.............................................................................................................174
display mld interface verbose.................................................................................................175
Field Descriptions.............................................................................................................175
display mld interface vlan-interface <vid>................................................................................177
Field Descriptions.............................................................................................................177
display mld interface vlan-interface <vid> verbose....................................................................178
Field Descriptions.............................................................................................................178
display mld routing-table.......................................................................................................180
display monitor-link group [group-number | all],.......................................................................181
Field Descriptions.............................................................................................................181
Operating Notes.............................................................................................................181
display multicast forwarding-table...........................................................................................183
display multicast routing-table.................................................................................................184
Operating Notes.............................................................................................................185
display multicast routing-table static.........................................................................................186
Field Descriptions.............................................................................................................186
Operating Notes.............................................................................................................186
display multicast rpf-info........................................................................................................188
display ospf cumulative.........................................................................................................189
Field Descriptions.............................................................................................................189
Operating Notes.............................................................................................................190
display ospf interface............................................................................................................191
Field Descriptions.............................................................................................................191
Operating Notes.............................................................................................................191
display ospf lsdb..................................................................................................................193
Field Descriptions.............................................................................................................193
Operating Notes.............................................................................................................193
display ospf peer..................................................................................................................195
Field Descriptions.............................................................................................................195
Operating Notes.............................................................................................................195
display ospf routing..............................................................................................................197
Field Descriptions.............................................................................................................197
Operating Notes.............................................................................................................197
display ospf vlink..................................................................................................................198
Contents
7
Field Descriptions.............................................................................................................198
Operating Notes.............................................................................................................198
display ospfv3.....................................................................................................................200
Operating Notes.............................................................................................................200
display ospfv3 area area-id peer interface interface-type interface number...................................201
Field Descriptions.............................................................................................................201
Operating Notes.............................................................................................................201
display ospfv3 area area-id peer peer-router-id.........................................................................202
Field Descriptions.............................................................................................................202
Operating Notes.............................................................................................................202
display ospfv3 area area-id peer verbose................................................................................204
Field Descriptions.............................................................................................................204
Operating Notes.............................................................................................................204
display ospfv3 interface........................................................................................................205
Field Descriptions.............................................................................................................205
Operating Notes.............................................................................................................206
display ospfv3 lsdb...............................................................................................................208
display ospfv3 lsdb statistics..................................................................................................210
display ospfv3 peer..............................................................................................................211
Field Descriptions.............................................................................................................211
Operating Notes.............................................................................................................211
display ospfv3 peer peer-router-id...........................................................................................213
Field Descriptions.............................................................................................................213
Operating Notes.............................................................................................................213
display ospfv3 peer statistics..................................................................................................215
display ospfv3 peer verbose..................................................................................................216
Field Descriptions.............................................................................................................216
Operating Notes.............................................................................................................216
display ospfv3 statistic..........................................................................................................218
Field Descriptions.............................................................................................................218
Operating Notes.............................................................................................................218
display ospfv3 vlink..............................................................................................................220
Field Descriptions.............................................................................................................220
Operating Notes.............................................................................................................220
display pim bsr-info...............................................................................................................222
Field Descriptions.............................................................................................................222
Operating Notes.............................................................................................................223
display pim control-message counters......................................................................................224
display pim grafts.................................................................................................................225
display pim interface.............................................................................................................226
Field Descriptions.............................................................................................................226
Operating Notes.............................................................................................................226
display pim interface verbose.................................................................................................227
Field Descriptions.............................................................................................................227
Operating Notes.............................................................................................................228
display pim join-prune...........................................................................................................230
display pim neighbor............................................................................................................231
Field Descriptions.............................................................................................................231
Operating Notes.............................................................................................................231
display pim neighbor <ip> verbose.........................................................................................233
Field Descriptions.............................................................................................................233
Operating Notes.............................................................................................................233
display pim routing-table.......................................................................................................235
display pim rp-info................................................................................................................236
display poe device...............................................................................................................237
8
Contents
Operating Notes.............................................................................................................237
display poe interface............................................................................................................238
Operating Notes.............................................................................................................239
display poe interface power...................................................................................................240
Operating Notes.............................................................................................................241
display poe power-usage.......................................................................................................242
Operating Notes.............................................................................................................242
display poe-power alarm.......................................................................................................243
display poe-power switch state...............................................................................................244
display port trunk.................................................................................................................245
display power......................................................................................................................246
Field Descriptions.............................................................................................................246
display protocol-vlan.............................................................................................................247
display protocol-vlan interface................................................................................................248
display proxy-arp.................................................................................................................249
Operating Notes.............................................................................................................249
display public-key local rsa public...........................................................................................250
Operating Notes.............................................................................................................250
display public-key peer..........................................................................................................251
Field Descriptions.............................................................................................................251
display radius scheme...........................................................................................................252
Field Descriptions.............................................................................................................253
Operating Notes.............................................................................................................253
display rip...........................................................................................................................256
display rip interface..............................................................................................................257
display rip process-id ip-address mask/mask-length...................................................................258
display rip process-id route....................................................................................................259
display rip process-id route peer ip-address..............................................................................260
display rmon statistics...........................................................................................................261
Operating Notes.............................................................................................................261
display route-policy...............................................................................................................262
display saved-configuration....................................................................................................263
display saved-configuration by-linenum....................................................................................264
Operating Notes.............................................................................................................264
display schedule reboot.........................................................................................................265
Operating Notes.............................................................................................................265
display sflow display sflow slot <slot-number>..........................................................................266
display snmp-agent community...............................................................................................267
Operating Notes.............................................................................................................267
display snmp-agent group......................................................................................................268
Operating Notes.............................................................................................................269
display snmp-agent local-engineid..........................................................................................270
Field Descriptions.............................................................................................................270
Operating Notes.............................................................................................................270
display snmp-agent mib-view..................................................................................................271
Operating Notes.............................................................................................................271
display snmp-agent statistics...................................................................................................272
display snmp-agent sys-info....................................................................................................273
Operating Notes.............................................................................................................273
display snmp-agent trap-list....................................................................................................274
Operating Notes.............................................................................................................274
display snmp-agent usm-user..................................................................................................275
Operating Notes.............................................................................................................275
display ssh client source........................................................................................................276
display ssh server session......................................................................................................277
Contents
9
Operating Notes.............................................................................................................277
display ssh server status.........................................................................................................278
Field Descriptions.............................................................................................................278
display ssh server-info...........................................................................................................279
display ssl client-policy..........................................................................................................280
Operating Notes.............................................................................................................280
display ssl server-policy.........................................................................................................281
Operating Notes.............................................................................................................281
display startup.....................................................................................................................283
display stp...........................................................................................................................284
display stp abnormal-port......................................................................................................286
display stp bpdu-statisticsdisplay stp bpdu-statistics interface GigabitEthernet <port-num>display stp
bpdu-statistics interface GigabitEthernet <port-num> instance <instanceNUM, 1-32>.....................287
display stp briefdisplay stp instance <instance-id> briefdisplay stp instance <instance-id> interface
GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> interface GigabitEthernet
<interface-id> briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> to
GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> slot <slot-id> briefdisplay stp
interface GigabitEnterface <port-num> briefdisplay stp interface GigabitEnterface <port-num> to
GigabitEnterface <port-num> brief..........................................................................................289
display stpdisplay stp instance <instance-id> interface GigabitEthernet 1/0/1/display stp slot
<slot-num>...........................................................................................................................291
display stp down-port............................................................................................................293
Operating Notes.............................................................................................................293
display stp history display stp history slot <slot-number>display stp instance <instance-id>history slot
<slot-no>display stp instance <instance-id>history.....................................................................294
display stp instance <instanceid> tcdisplay stp instance <instanceid> tc slot <slot-no>display stp
tc.......................................................................................................................................295
display stp region-configuration..............................................................................................296
display stp root....................................................................................................................297
display switchover state.........................................................................................................298
Field Descriptions.............................................................................................................298
Operating Notes.............................................................................................................298
display system-failure............................................................................................................300
Operating Notes.............................................................................................................300
display this..........................................................................................................................301
display transceiver alarm interface..........................................................................................302
Field Descriptions.............................................................................................................302
Operating Notes.............................................................................................................303
display transceiver diagnosis interface.....................................................................................306
Field Descriptions.............................................................................................................306
Operating Notes.............................................................................................................306
display transceiver interface...................................................................................................308
Field Descriptions.............................................................................................................308
Operating Notes.............................................................................................................309
display transceiver manuinfo interface.....................................................................................310
Field Descriptions.............................................................................................................310
Operating Notes.............................................................................................................310
display user-bind..................................................................................................................312
Operating Notes.............................................................................................................312
display vlan.........................................................................................................................313
display vrrp.........................................................................................................................314
Field Descriptions.............................................................................................................314
display vrrp interface <interface-type> vrid <virtual routerid>.....................................................316
display vrrp statistics.............................................................................................................317
Field Descriptions.............................................................................................................317
10
Contents
display vrrp statistics interface <interface-type> vrid <virtual router-id>.........................................319
display vrrp verbose..............................................................................................................320
3 Fundamental Commands.........................................................................322
backup startup-configuration..................................................................................................322
Operating Notes.............................................................................................................322
clock datetime......................................................................................................................323
Operating Notes.............................................................................................................323
clock summer-time one-off......................................................................................................324
Operating Notes.............................................................................................................324
clock summer-time repeating..................................................................................................325
Operating Notes.............................................................................................................325
clock timezone.....................................................................................................................326
Operating Notes.............................................................................................................326
command accounting............................................................................................................327
Operating Notes.............................................................................................................327
command authorization.........................................................................................................328
Operating Notes.............................................................................................................328
command-alias enable..........................................................................................................329
command-alias mapping.......................................................................................................330
copy...................................................................................................................................331
Operating Notes.............................................................................................................331
delete <startup-config>..........................................................................................................332
Operating Notes.............................................................................................................332
flow-control..........................................................................................................................333
Operating Notes.............................................................................................................333
idle-timeout..........................................................................................................................334
Operating Notes.............................................................................................................334
quit.....................................................................................................................................335
Operating Notes.............................................................................................................335
reboot.................................................................................................................................336
Operating Notes.............................................................................................................336
reset saved-configuration.......................................................................................................337
Operating Notes.............................................................................................................337
restore startup-configuration...................................................................................................338
Operating Notes.............................................................................................................338
return..................................................................................................................................339
Operating Notes.............................................................................................................339
save....................................................................................................................................340
Operating Notes.............................................................................................................340
schedule reboot at................................................................................................................341
Operating Notes.............................................................................................................341
schedule reboot delay...........................................................................................................342
Operating Notes.............................................................................................................342
screen-length........................................................................................................................343
Operating Notes.............................................................................................................343
set authentication password...................................................................................................344
Operating Notes.............................................................................................................344
speed.................................................................................................................................345
Operating Notes.............................................................................................................345
startup saved-configuration....................................................................................................346
Operating Notes.............................................................................................................346
sysname..............................................................................................................................347
Operating Notes.............................................................................................................347
system-view..........................................................................................................................348
Contents
11
Operating Notes.............................................................................................................348
telnet..................................................................................................................................349
Operating Notes.............................................................................................................349
telnet ipv6...........................................................................................................................350
Operating Notes.............................................................................................................350
telnet server enable...............................................................................................................351
Operating Notes.............................................................................................................351
terminal type........................................................................................................................352
Operating Notes.............................................................................................................352
tftp.....................................................................................................................................353
Operating Notes.............................................................................................................353
tftp ipv6..............................................................................................................................354
Operating Notes.............................................................................................................354
undo...................................................................................................................................355
Operating Notes.............................................................................................................355
4 Comware Configuration Help Commands..................................................356
Table of Comware Commands and Associated ProVision Commands..........................................356
Using the Comware-Help Command.......................................................................................359
Logging In and Usernames................................................................................................359
Enabling SSH..................................................................................................................360
Ports and VLANs..............................................................................................................360
Index.......................................................................................................361
12
Contents
Product Documentation
About Your Switch Manual Set
NOTE: For the latest version of all HP switch documentation, including Release Notes covering
recently added features, please visit the HP Networking web site at www.hp.com/Networking/
support.
Electronic Publications
The latest version of each of the publications listed below is available in PDF format on the HP
Networking web site, as described in the Note at the top of this page.
•
Installation and Getting Started Guide—Explains how to prepare for and perform the physical
installation and connect the switch to your network.
•
Basic Operation Guide—Describes how to use the switch interfaces and introduces basic
operations.
•
Management and Configuration Guide—Describes how to configure, manage, and monitor
basic switch operation.
•
Advanced Traffic Management Guide—Explains how to configure traffic management features
such as VLANs, MSTP, QoS, and Meshing.
•
Multicast and Routing Guide—Explains how to configure IGMP, PIM, IP routing, and VRRP
features.
•
Access Security Guide—Explains how to configure access security features and user
authentication on the switch.
•
IPv6 Configuration Guide—Describes the IPv6 protocol operations that are supported on the
switch.
•
Command Line Interface Reference Guide—Provides a comprehensive description of CLI
commands, syntax, and operations.
•
Event Log Message Reference Guide—Provides a comprehensive description of event log
messages.
•
Comware CLI Commands in Provision Software—Lists and describes the Comware CLI
commands supported in ProVision Software.
•
Release Notes—Describe new features, fixes, and enhancements that become available
between revisions of the main product guide.
About Your Switch Manual Set
13
1 Introduction To the ProVision CLI
Comware Command Support in ProVision Software
The selected Comware CLI commands described in this guide are included in the ProVision software
CLI to help Comware-experienced network management staff learn to use the ProVision software
CLI with a minimum of effort.
This edition of Comware CLI Commands in ProVision Software describes the operation and output
of selected Comware display commands added to the ProVision software. Included are related
ProVision software commands and references to further information on configuring the features
reflected in the display command output.
Refer to the latest release notes for your switch product to determine whether Comware commands
are supported.
HP Networking Switches Running Comware
Software
HP Networking Switches Running ProVision Software with Comware
CLI Commands Included*
3100
5120 El
5820
3500
3300
5120 Sl
5830
3500 yl
3600
5500
5900
5400 zl
3610
5500 E
7500
6200 yl
4200G
5500 Hl
9500
6600
4210
5500 SL
10500
8200 zl
4210G
5500G
12500
4500G
5800
4510G
5810
3800
2910al
2615
2920
2915
2620
4800G
*As of October, 2012. Supported commands depend on software version running on the switch.
Commands Added to the Software Over Several Releases. The Comware command set available
on your switch is determined by the code version it is running. Each command description in this
guide includes the minimum software version supporting that command. For example, a minimum
version of 15.10 means that a switch running K-code must be using Release K.15.10 or greater
and a switch running RA-code must be using RA.15.10 or greater.
Listing Display Commands in the CLI
Use this command: display ?
For example:
HP Switch> display ?
boot-loader
clock
command-alias
debugging
dns
gvrp
history-command
igmp
ip
lacp
link-aggregation
memory
14
Introduction To the ProVision CLI
Display boot loader information
Clock status and configuration information.
Display command alias
Current setting of debugging switches.
DNS status and configuration information
GARP VLAN Registration Protocol
The historical command information.
IGMP status and configuration information
Specify IP(Internet Protocol) configuration information.
Display LACP protocol information
Display Link-aggregation information
Display memory information.
mld
ospf
ospfv3
schedule
snmp-agent
HP Switch> display
MLD status and configuration information.
Open Shortest Path First (OSPF)
Open Shortest Path First for IPv6 (OSPFv3)
Schedule system task
SNMP status and configuration information
Listing Display Commands in the CLI
15
CLI Operation
Comparing Comware and ProVision Commands
Comware display commands and ProVision software show commands produce status information
used for monitoring, troubleshooting, and auditing the switch network environment and configuration.
•
Like show commands, using display commands does not change the switch operating mode.
•
Comware display commands are additional commands supported in ProVision software, and
do not replace any existing ProVision commands.
Output Differences Between Display and Show commands
The output fields from display commands and their show command counterparts include differences
in the names, numbers and types of information fields. For example the results for the following
commands have two instances where there is not a comparable mapping between Comware and
ProVision:
Comware
Related ProVision
display dns < domain | server >
show ip dns
show ip
DNS Field Mappings
Comware
Related ProVision
No.
n/a
DNS Server
Priority
Type
DNS Mode
Domain-name
Domain Suffix
IP Address
DNS Server Addresses
n/a
DNS Servers Configured
Using both the display commands and their show command counterparts can in some cases result
in more information output than using only one or the other.
In some cases, a field populated in Comware display output is not populated in the corresponding
display output in ProVision software. This is often due to MIB (Management Information Base)
differences between Comware and ProVision software. Also, in rare cases, the Comware display
output in ProVision software includes fields that are not included in the same display command
output in Comware software.
Using CLI Context Levels
ProVision software operates in these CLI context levels:
16
Level
Prompt
Operator
HP Switch>
Manager
HP Switch#
enable
Global Configuration
HP Switch(config)#
config
Context Configuration
HP Switch(vlan-1)#
vlan n
HP Switch(eth-A1-A6)#
interface << portx >[-portn] >
Introduction To the ProVision CLI
Context Keyword
Use exit to return to the next-highest context level.
Listing Commands Available at Any Context Level. At a given context level you can list and execute
the commands that level offers, plus all of the commands available at preceding levels. To list
available commands, use the [?] key. For example:
HP Switch# show vlans ?
custom
Show vlan parameters in customized order. ports
Show VLANs that have at least one port from the 'PORT-LIST' as a member. VLAN-ID
Show detailed VLAN information for the VLAN with the ID supplied. <cr>
Use the [Tab] or [?] Key To Complete a Command Keyword. You can use [Tab] or [?] to help you
find CLI commands or to quickly complete a keyword. For example:
HP Switch(config) # show ip a[Tab] aspath-list authorized-managers
HP Switch(config) # show ip au[?] HP Switch(config)# show ip authorized-managers [Enter]
IPV4 Authorized Managers
-----------------------Address : 10.10.123.39
Mask
: 255.255.255.255
Access : Manager
Access Method : all
Empty Output
In some cases where the MIB is not holding information for a feature, the related display command(s)
will return only the system prompt. For example, IGMP can be configured, but no data will be
displayed unless one or more multicast groups have been joined. For example, using display igmp
group when there are no joined multicast groups returns only the system prompt:
HP Switch# display igmp group
HP Switch#
Further CLI Operating Information
For more information on using the CLI, refer to the chapter titled "Using the Command Line Interface
(CLI)" in the latest Basic Operation Guide for your switch.
To access the latest software manual set for your switch, visit http://www.hp.com/support/manuals.
CLI Operation
17
2 Display Commands
display acl <acl-number> | name <acl-name>>
Comware
Related Provision
display acl <acl-number> | name <acl-name>>
show access-list <number | name>
Displays configuration and match statistics for the specified or all IPv4 ACLs. This command displays
ACL rules in config or depth-first order, whichever is configured.
HP Switch# display acl 2001
Basic ACL 2001, named -flow-, 2 rules,
Statistics enabled
ACL's step is 5
rule 1 permit source 1.1.1.1 0 (5 times matched)
rule 2 permit source 1.1.1.2 0 (No statistics resource)
Field Descriptions
Basic ACL 2001: Category and number of the ACL. The following field information is about IPv4
basic ACL 2001.
named flow: The name of the ACL is flow. "-none-" means the ACL is not named.
2 rules: The ACL contains two rules.
Statistics enabled: The rule match counting is enabled for this ACL.
ACL's step is 5: The rule numbering step is 5.
5 times matched: There have been five matches for the rule. The statistic counts only ACL matches
in the packet filter. This field is not displayed when no packets have matched the rule.
No statistics resource: Resources are not enough for counting matches for the IPv4 rules.
This information indicates that the switch failed to allocate resources for counting matches for the
rule when you applied the packet-filter command to an interface. Even if resources have become
available after that, the switch does not change the information or count matches for the rule. To
count matches for the rule, you must delete and then add the rule.
Uncompleted: Applying the rule to hardware failed because no sufficient resources were available
or the hardware does not support the rule. This event might occur when you modify a rule in an
ACL that has been applied.
Operating Notes
For more information, see the “Access Control Lists (ACLs)” chapter in the latest Access Security
Guide for your switch.
Minimum Software Version: 15.11.
Example of Related ProVision Software Command Output.
HP Switch(config)# show access-list 1
Access Control Lists
Name: 1
Type: Standard
Applied: No
SEQ Entry
----------------------------------------------------------------------------18
Display Commands
10 Action: deny
IP
: 0.0.0.0
Mask: 255.255.255.255
20 Action: permit
IP
: 1.2.3.4
Mask: 0.0.0.255
display arp
Comware
Related Provision
display arp
show arp
Displays ARP (Address Resolution Protocol) configuration information.
HP Switch(config)# display arp
Type: S-Static
D-Dynamic
L-Local
I-Invalid
IP Address MAC Address VLAN ID Interface
120.85.204.1 002347-bbd940 1 1
n/a
O-Other
Aging Type
D
Field Descriptions
IP Address: IP address in an ARP entry.
MAC Address: MAC address in an ARP entry.
VLAN ID: VLAN ID contained in a static ARP entry.
Interface: Outbound interface in an ARP entry.
Aging: Age timer for a dynamic ARP entry in minutes.
Type: ARP entry type:
•
D for Dynamic
•
S for Static
•
L for Local
•
I for Invalid
•
O for Other
Operating Notes
The types "A" for authorized, and "M" for multiple ports, are not supported.
For more on switch ARP operation, refer to the "IP Routing" chapter in the latest Multicast and
Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# show arp
IP ARP table
IP Address
--------------15.255.128.1
15.255.130.156
15.255.131.209
MAC Address
----------------00000c-07ac00
001635-679d6c
0025b3-4afd68
Type
------dynamic
dynamic
dynamic
Port
---1
1
1
display arp
19
display arp Field Mappings.
20
Comware
ProVision Software
IP Address
IP Address
MAC Address
MAC Address
VLAN ID
n/a
Interface
Port
Aging
n/a
Type
Type
Display Commands
display arp <ip-address>
Comware
Related ProVision
display arp <ip-address>
show arp
Displays ARP entries in the ARP mapping table. If no parameter is specified, all ARP entries are
displayed.
HP Switch# display arp 20.1.1.1
IP Address
20.1.1.1
Type: S-Static
MAC Address
002347-bbd940
D-Dynamic
L-Local
VLAN ID Interface
1
1
I-Invalid
O-Other
Aging Type
n/a
D
Field Descriptions
IP Address: IP address in an ARP entry.
MAC Address: MAC address in an ARP entry.
VLAN ID: VLAN ID contained a static ARP entry.
Interface: Outbound interface in an ARP entry.
Aging: Age timer for a dynamic ARP entry in minutes (DIS or N/A indicates that the aging timer
is unknown or there is no age timer).
Type: ARP entry type:
•
D for dynamic
•
S for static
•
A for authorized
•
M for multiple ports
Vpn-instance Name: Name of VPN instance. [No Vrf] indicates that no VPN instance is configured
for the ARP entry.
Operating Notes
For more information, see the “IP Routing Features” chapter in the latest Multicast and Routing
Guide for your switch.
Minimum Software Version: 15.11.
Example of Related ProVision Software Command Output.
HP Switch(config)# show arp
IP ARP table
IP Address
MAC Address
Type
Port
------------- --------------- ------ ---10.10.10.2
abcdef-123456
D
1
display arp <ip-address>
21
display arp detection
Comware
Related ProVision
display arp detection
show arp-protect
Displays arp-protected VLANs.
HP Switch# display arp detection
ARP detection is enabled in the following VLANs:
1-100
Example of Related ProVision Software Command Output.
HP Switch# show arp-protect
ARP Protection Information
Enabled Vlans : 1-4094
Validate : dest-mac, src-mac
Port Trust
----- ----B1 Yes
B2 Yes
B3 No
B4 No
B5 No
For more information, see the latest Access Security Guide for your switch.
22
Display Commands
display arp detection statistics
Comware
Related ProVision
display arp detection statistics
show arp-protection statistics
Displays the statistics of the detected arp.
HP Switch# display arp detection statistics
ARP detection is enabled in the following VLANs:
1-10
ARP Protection Counters for VLAN 1
ARPs forwarded
Bad bindings
Malformed pkts
: 0
: 0
: 0
Bad Sender/Target IP
: 0
Source/Sender MAC mismatches : 0
Dest/Target
MAC mismatches : 0
ARP Protection Counters for VLAN 2
ARPs forwarded
Bad bindings
Malformed pkts
: 0
: 0
: 0
Bad Sender/Target IP
: 0
Source/Sender MAC mismatches : 0
Dest/Target
MAC mismatches : 0
ARP Protection Counters for VLAN 10
ARPs forwarded
Bad bindings
Malformed pkts
: 0
: 0
: 0
Bad Sender/Target IP
: 0
Source/Sender MAC mismatches : 0
Dest/Target
MAC mismatches : 0
ARP Protection Counters for VLAN 12
ARPs forwarded
Bad bindings
Malformed pkts
: 0
: 0
: 0
Bad Sender/Target IP
: 0
Source/Sender MAC mismatches : 0
Dest/Target
MAC mismatches : 0
Example of Related ProVision Software Command Output.
HP Switch# show arp-protect statistics
ARP Protection Counters for VLAN 1
ARPs forwarded : 0
Bad Sender/Target IP
: 0
Bad bindings
: 0
Source/Sender MAC mismatches : 0
Malformed pkts : 0
Dest/Target MAC mismatches
: 0
Minimum Software Version: 15.10.
display arp detection statistics
23
display arp ip-address
Comware
Related ProVision
display arp ip-address
show arp
Displays the ARP entry for a specified IP address.
HP Switch# display arp 20.1.1.1
Type: S-Static
IP Address
20.1.1.1
D-Dynamic
MAC Address
002347-bbd940
L-Local
VLAN ID
1
I-Invalid
O-Other
Interface Aging Type
1
n/a
D
Example of Related ProVision Software Command Output.
HP Switch# show
IP ARP table
IP Address
--------------15.255.128.1
15.255.131.19
15.255.133.150
arp
MAC Address
----------------00000c-07ac00
00a0c9-b1503d
000bcd-3cbeec
Type
Port
------- ---dynamic B1
dynamic
dynamic B1
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
24
Display Commands
display boot-loader
Comware
Related ProVision
display boot-loader
show flash
Displays the current flash memory precedence and the source of the current boot file (software
image). The switch has two flash memory locations: primary and secondary. In the display
boot-loader output:
•
btm.swi is the primary flash memory.
•
secondary.swi is the secondary flash memory.
When the switch is configured with primary flash as the default boot source, this command shows
that the primary boot file (software image) is in primary flash (btm.swi):
HP Switch# display boot-loader
The next primary boot file of MM is: flash:/cfa0/btm.swi
The next backup boot file of MM is: flash:/cfa0/secondary.swi
The current boot file of MM is: flash:/cfa0/btm.swi
When the switch is configured with secondary flash as the default boot source, this command
shows that the primary boot file (software image) is in secondary flash (secondary.swi):
HP Switch# display boot-loader
The next primary boot file of MM is: flash:/cfa0/secondary.swi
The next backup boot file of MM is: flash:/cfa0/btm.swi
The current boot file of MM is: flash:/cfa0/secondary.swi
Field Descriptions
next primary boot file: The current default flash memory location for the next reload or boot
operation. Can be either the primary or secondary flash.
next backup boot file: The current non-default flash memory location. Can be either the primary
or secondary flash.
current boot file: The flash memory location from which the switch was last booted. Can be either
primary or secondary flash.
NOTE: “of MM” appears in the display boot-loader output on switches that support dual memory
modules, and refers to the current active (Actv) memory module.
Operating Notes
Both the primary flash and a secondary flash contain a software image. Any valid software image
can be loaded into either flash memory.
This command indicates which flash memory is the default when the switch is booted with any of
the following commands:
reload
boot [system ]
To change the flash memory default, use this command:
boot set-default flash < primary | secondary >
For more on switch memory operation, refer to the “Switch Memory and Configuration” chapter
in the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision software Command Output.
display boot-loader
25
HP Switch# show flash
Image
Size (bytes) Date
Version
----------------- ------------ -------- -------------Primary Image
:
Secondary Image
:
14995368 12/20/11 K.15.07.0003
14995368 12/20/11 K.15.08.0001
Boot ROM Version : K.15.26
Default Boot
: Primary
Boot-Loader Field Mappings.
26
Comware
ProVision software
btm.swi
Primary Image
secondary.swi
Secondary Image
n/a
Boot ROM Version
current boot file
Default Boot
Display Commands
display clock
Comware
Related ProVision
display clock
show time
show system information
Displays the current time, time zone, day, and date setting on the switch.
HP Switch# display clock
16:07:27 GMT Mon 03/16/2012
Field Descriptions:
Time: Current time in HH:MM:SS format on the switch.
Time Zone: GMT (default) or the configured time zone.
Day: Mon, Tue, Wed, Thu, Fri, Sat, Sun
Date: MM/DD/YYYY format
Operating Notes
To configure time, date, daylight-time-rule, time zone and other time or date settings on the switch,
use the following commands in the config context to list the time and date command options:
time ?
clock ?
Minimum Software Version: 15.08
Example of Related ProVision Software Command Output.
HP Switch# show time
Mon Mar 16 16:07:56 2012
The output of the ProVision software show system information command includes the switch’s time
zone and Daylight Time Rule settings.
To configure time and date settings on the switch, use the clock and time commands in the config
context. For more information, see the “Time Protocols” chapter in the latest Management and
Configuration Guide for your switch.
display clock
27
display command-alias
Comware
Related ProVision
display command-alias
show alias
Displays any defined command aliases and their corresponding command assignments configured
on the switch. For example, suppose the following aliases are configured:
Alias
Full Command
sst
show startup-config
srun
show running-config
With the above alias configuration, the display output would be as follows:
HP Switch(config)# display command-alias
index
alias
command key
1
sst
show startup-config
2
srun
show runnning-config
Field Descriptions
index: The sequence number for each alias.
alias: The character string.
command key: The command called by the alias.
Operating Notes
To configure an alias in ProVision software, use the following command.
alias < alias-name-str > < command-str >
For more on the alias command, refer to the chapter titled “Using the Command Line Interface
(CLI)” in the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision software Command Output.
HP Switch(config)# show alias
Name
-------------------------------sst
srun
Command
-------------------------show startup-config
show runnning-config
Alias Field Mappings.
28
Comware
ProVision Software
index
n/a
alias
Name
command key
Command
Display Commands
display counters
Comware
Related ProVision
display clock
show interface <port>
Displays traffic statistics for interfaces.
HP Switch# display counters inbound interface
Interface Total(pkts) Broadcast(pkts) Multicast(pkts) Err(pkts)
A1
11
2
5
0
A2
0
0
0
0
A3
0
0
0
0
A4
0
0
0
0
A5
0
0
0
0
A6
0
0
0
0
A7
0
0
0
0
.
.
.
HP Switch# display counters outbound interface
Interface Total(pkts) Broadcast(pkts) Multicast(pkts) Err(pkts)
A1
13
6
6
0
A2
0
0
0
0
A3
0
0
0
0
A4
0
0
0
0
A5
0
0
0
0
A6
0
0
0
0
A7
0
0
0
0
.
.
.
Field Descriptions
Interface: Abbreviated interface name.
Total (pkts): Total number of packets received or sent through the interface.
Broadcast (pkts): Total number of broadcast packets received or sent through the interface. On an
RPR physical port, all broadcast and multicast packets received or sent are displayed as multicast
packets.
Multicast (pkts): Total number of multicast packets received or sent through the interface. On an
RPR physical port, all broadcast and multicast packets received or sent are displayed as multicast
packets.
Err (pkts): Total number of error packets received or sent through the interface.
Overflow: more than 14 decimal digits(7 digits for column "Err"): The command displays Overflow
in any of the following cases:
•
The data length of an error statistic is greater than 7 decimal digits.
The data length of a non-error statistic is greater than 14 decimal digits.
--: not supported: The statistical item is not supported.
Operating Notes
For more information on interface counters, see the "Port Status and Configuration" chapter in the
latest Management and Configuration Guide for your switch.
display counters
29
Example of Related ProVision Software Command Output.
HP Switch(config)# show interface a1
Status and Counters - Port Counters for port A1
Name : O&rsquo;Connor@10.25.101.43
MAC Address
: 001871-b995ff
Link Status
: Up
Totals (Since boot or last clear) :
Bytes Rx
: 2,763,197 Bytes Tx : 22,972
Unicast Rx
: 2044 Unicast Tx : 128
Bcast/Mcast Rx : 23,456 Bcast/Mcast Tx : 26
Errors (Since boot or last clear) :
FCS Rx
: 0
Drops Tx : 0
Alignment Rx
: 0
Collisions Tx : 0
Runts Rx
: 0
Late Colln Tx : 0
Giants Rx
: 0
Excessive Colln : 0
Total Rx Errors: 0
Deferred Tx : 0
Others (Since boot or last clear) :
Discard Rx
: 0
Out Queue Len : 0
Unknown Protos : 0
Rates (5 minute weighted average) :
Total Rx (bps) : 3,028,168
Total Tx (bps) : 1,918,384
Unicast Rx (Pkts/sec): 5
Unicast Tx (Pkts/sec) : 0
B/Mcast Rx (Pkts/sec): 71
B/Mcast Tx (Pkts/sec) : 0
Utilization Rx : 00.30 %
Utilization Tx : 00.19 %
display counters Field Mappings.
30
Comware
ProVision Software
Interface
port
Total (pkts)
Bytes Rx and Bytes Tx
Broadcast (pkts)
Bcast/Mcast Rx and Bcast/ Mcast Tx
Multicast (pkts)
Bcast/Mcast Rx and Bcast/ Mcast Tx
Err (pkts)
Errors
Overflow:
n/a
-: not supported
n/a
Display Commands
display counters rate
Comware
Related ProVision
display counters rate
show int <int>
Displays traffic rate statistics over the last 300 seconds. The statistics cover only interfaces in up
state.
HP Switch# display counters rate outbound interface
Interface Total(pkts/sec) Broadcast(pkts/sec) Multicast(pkts/sec)
A1
84
0
42
A2
0
0
0
Overflow: n/a
--: not supported.
HP-5406zl# display counters rate inbound interface
Interface Total(pkts/sec) Broadcast(pkts/sec) Multicast(pkts/sec)
A1
0
0
0
A2
88
0
44
Overflow: n/a
--: not supported.
When all ports are down:
HP Switch# display counters rate outbound interface
No statistics, or no counted interface.
Example of Related ProVision Software Command Output.
HP Switch# show int custom 1-4 port name:4 type vlan intrusion
speed enabled mdi
Status and Counters - Custom Port Status
Intrusion
Port Name Type VLAN
Alert
Speed
Enabled MDI-mode
---- ---- --------------- --------- ------- -----1
Acco 100/1000T 1
No
1000FDx
Yes
Auto
2
Huma 100/1000T 1
No
1000FDx
Yes
Auto
3
Deve 100/1000T 1
No
1000FDx
Yes
Auto
4
Lab1 100/1000T 1
No
1000FDx
Yes
Auto
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display counters rate
31
display cpu-usage
Comware
Related ProVision
display cpu-usage
show cpu [slot <SLOT-ID-RANGE> [<time>] | <time>]
Displays average CPU usage statistics for 5 seconds, 1 minute and 5 minutes.
HP Switch# display cpu-usage
Master CPU usage:
6% in last 5 seconds
4% in last 1 minute
3% in last 5 minutes
Example of Related ProVision Software Command Output.
HP Switch# show cpu
2 percent busy, from
1 sec ave: 9 percent
5 sec ave: 9 percent
1 min ave: 1 percent
2865 sec ago
busy
busy
busy
% CPU | Description
-------+-------------------------99
| Idle
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
32
Display Commands
display cpu-usage history
Comware
Related ProVision
display cpu-usage history
No equivalent ProVision software command
Displays the history CPU utilization rates in a coordinate plane. The system collects the statistics
of history CPU utilization rates at a certain interval and saves the statistics in the history record
area. You can use the this command to display the history CPU utilization rates in the last 5 minutes.
The history CPU utilization rates are displayed through x and y coordinates.
Any CPU utilization statistics value takes the closest y-coordinate value. For example, a statistics
value of 53% is displayed as 55%, and a statistics value of 52% is displayed as 50%.
A number sign (#) shows the CPU utilization rate at a time point. If more than one number sign
exists at a time point, the highest one represents the CPU utilization rate of the time point.
HP Switch# display cpu-usage history
100%|
95%|
90%|
85%|
80%|
75%|
70%|
65%|
60%|
55%|
50%|
45%|
40%|
35%|
30%|
25%|
20%|
15%|
10%|
5%|########################################################
--------------------------------------------------------50
100
150
200
250
300 (seconds)
cpu-usage last 05 minutes(SYSTEM)
Minimum Software Version: 15.10.
display cpu-usage history
33
display current-configuration
Comware
Related ProVision
display current-configuration
show running-configuration
Displays the current configuration.
HP Switch# display current-configuration
J8697A Configuration Editor; Created on release #K.15.09.0000x
Ver #03:01.1f.ef:f2
hostname "HP-5406zl"
module 1 type J9536A
module 6 type J9534A
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged A1-A22,F1-F24
ip address dhcp-bootp
exit
Example of Related ProVision Software Command Output.
HP Switch# show running-config
Running configuration:
; J9087A Configuration Editor; Created on release #R.11.XX
hostname "Switch"
snmp-server community "public" Unrestricted
snmp-server host 15.255.133.236 "public"
snmp-server host 15.255.133.222 "public"
snmp-server host 15.255.133.70 "public"
snmp-server host 15.255.134.235 "public"
vlan 1
name "DEFAULT_VLAN"
untagged 1-28
ip address dhcp-bootp
exit
snmp-server enable traps mac-notify mac-move
snmp-server enable traps mac-notify trap-interval 60
snmp-server enable traps mac-notify
mac-notify traps 5-6 learned
mac-notify traps 3-4 removed
For more information, see the latest Management and Configuration Guide for your switch.
34
Display Commands
display current-configuration by-linenum
Comware
Related ProVision
display current-configuration by-linenum
show running-configuration
Displays the number of each line.
HP Switch# display current-configuration by-linenum
1: J8697A Configuration Editor; Created on release
#K.15.09.0000x
2: Ver #03:01.1f.ef:f2
3: hostname "HP-5406zl"
4: module 1 type J9536A
5: module 6 type J9534A
6: snmp-server community "public" Unrestricted
7: vlan 1
8: name "DEFAULT_VLAN"
9: untagged A1-A22,F1-F24
10: ip address dhcp-bootp
11: exit
Example of Related ProVision Software Command Output.
HP Switch# show running-config
Running configuration:
; J9087A Configuration Editor; Created on release #R.11.XX
hostname "Switch"
snmp-server community "public" Unrestricted
snmp-server host 15.255.133.236 "public"
snmp-server host 15.255.133.222 "public"
snmp-server host 15.255.133.70 "public"
snmp-server host 15.255.134.235 "public"
vlan 1
name "DEFAULT_VLAN"
untagged 1-28
ip address dhcp-bootp
exit
snmp-server enable traps mac-notify mac-move
snmp-server enable traps mac-notify trap-interval 60
snmp-server enable traps mac-notify
mac-notify traps 5-6 learned
mac-notify traps 3-4 removed
For more information, see the latest Management and Configuration Guide for your switch.
display current-configuration by-linenum
35
display current-configuration configuration
Comware
Related ProVision
display current-configuration configuration
No equivalent ProVision software command
Displays active configuration in the system excluding vlan and interface configuration. This command
is available only in manager mode.
HP Switch# display current-configuration configuration
hostname "HP-6200yl-24G"
module 1 type J8992A
alias "view" "show"
banner motd "\n"
radius-server host 10.10.10.1 key "abcd"
ip access-list extended "grp1"
exit
snmp-server community "public" Unrestricted
no snmpv3 enable
snmpv3 enable
snmpv3 group ComOperatorR user "user4" sec-model ver3
snmpv3 user "initial"
snmpv3 user "user4"
aaa port-access authenticator active
arp-protect
Minimum Software Version: 15.10.
36
Display Commands
display current-configuration interface
Comware
Related ProVision
display current-configuration interface
show running-configuration
Displays the interface configuration.
HP Switch# display current-configuration interface
vlan 1
name "DEFAULT_VLAN"
untagged A1-A22,F1-F24
ip address dhcp-bootp
exit
interface A1
untagged vlan 1
exit
interface A2
untagged vlan 1
exit
interface A3
untagged vlan 1
exit
interface A4
untagged vlan 1
exit
interface A5
untagged vlan 1
exit
interface A6
untagged vlan 1
exit
interface A7
untagged vlan 1
exit
interface A8
untagged vlan 1
exit
interface A9
untagged vlan 1
exit
interface A10
untagged vlan 1
exit
interface A11
untagged vlan 1
exit
interface A12
untagged vlan 1
exit
interface A13
untagged vlan 1
exit
interface A14
untagged vlan 1
exit
interface A15
untagged vlan 1
exit
interface A16
untagged vlan 1
exit
interface A17
display current-configuration interface
37
untagged vlan 1
exit
interface A18
untagged vlan 1
exit
interface A19
untagged vlan 1
Example of Related ProVision Software Command Output.
HP Switch# show running-config
Running configuration:
; J9087A Configuration Editor; Created on release #R.11.XX
hostname "Switch"
snmp-server community "public" Unrestricted
snmp-server host 15.255.133.236 "public"
snmp-server host 15.255.133.222 "public"
snmp-server host 15.255.133.70 "public"
snmp-server host 15.255.134.235 "public"
vlan 1
name "DEFAULT_VLAN"
untagged 1-28
ip address dhcp-bootp
exit
snmp-server enable traps mac-notify mac-move
snmp-server enable traps mac-notify trap-interval 60
snmp-server enable traps mac-notify
mac-notify traps 5-6 learned
mac-notify traps 3-4 removed
For more information, see the latest Management and Configuration Guide for your switch.
38
Display Commands
display debugging
Comware
Related ProVision
display debugging [ option ]
show debug
[buffer [-c < count > | -r | option-str ]]
Displays the options from any of the following lists that have debug logging enabled.
acl
distributed-trunking
ip
lldp
snmp
arp-protect
dynamic-ip-lockdown
ipv6
policy
vrrp
cdp
event
lacp
security
Using display debugging without specifying an option lists all options in the set that are enabled
for debug logging. For example, if acl, ip, lldp, and policy are enabled for debugging, this
command produces the following:
HP Switch# display debugging
ip ospf spf debugging is on
acl log debugging is on
lldp log debugging is on
policy route-map debugging is on
HP Switch#
Using display debugging with a specific option lists that option if it is enabled for debug logging.
If the command returns only the CLI prompt, then the option is not enabled for debug logging. For
example, if acl is enabled for debug logging and vrrp s not, this command produces the following:
HP Switch# display debugging
acl log debugging is on
HP Switch# display debugging vrrp
HP Switch#
Operating Notes
To configure debug operation in ProVision software, use the following command.
debug < option >
For more on configuring debug operation, refer to the chapter titled “Troubleshooting” in the latest
Management and Configuration Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch# show debug
Debug Logging
Source IP Selection: Outgoing Interface
Destination:
Memory buffer
Enabled debug types:
ip ospf spf
acl log
lldp log
policy route-map
display debugging
39
Debug Field Mappings.
40
Comware
ProVision Software
n/a
Source IP Selection
n/a
Destination
debug types listed
Enabled debug types
Display Commands
display default-configuration
Comware
Related ProVision
display default-configuration
No equivalent ProVision software command
Displays factory defaults of the switch, and all commands to be executed when the switch boots
with the factory defaults.
HP Switch# display default-configuration
; J8693A Configuration Editor; Created on release #K.15.09.0000x
; Ver #03:01.1f.ef:f2
vlan 1
name "DEFAULT_VLAN"
ip address dhcp-bootp
exit
Minimum Software Version: 15.10.
display default-configuration
41
display device
Displays the global enable/disable state of GVRP.
Comware
Related ProVision
display device
No equivalent ProVision software command
Displays physical modules present in the switch. This command also identifies the status of these
modules, whether they are up/active/standby or failed etc.
HP Switch# display device
SlotNo.
Brd Type
BrdStatus SubSlotNum
MM1 HP J9092A Management Modul... Standby n/a
MM2 HP J9092A Management Modul... Active n/a
SSM HP J9095A System Support M... Normal n/a
FM1 HP J9093A Fabric Module 82... Enabled n/a
FM2 HP J9093A Fabric Module 82... Enabled n/a
A
HP J9536A 20p GT PoE+/2p S... Up
n/a
SftVer PatchVer
K.15.09.0000x n/a
K.15.09.0000x n/a
K.15.09.0000x n/a
K.15.09.0000x n/a
K.15.09.0000x n/a
K.15.09.0000x n/a
Field Descriptions
Slot No.: Slot number of a card (standalone mode); slot number of a card on the specified member
switch in the format of member ID/slot number (IRF mode)
Brd Type: Hardware type of a card, which can be the following values:
•
Specific card model, such as LST1MRPNC1, which is the same as the silkscreen.
•
NONE: No card is in the slot.
•
UNKNOWN: The card is not supported by the software version and thus cannot start normally.
Brd Status: Card status, which can be the following values:
•
Absent: No card is in the slot.
•
Master: The card is an AMB.
•
Slave: The card is an SMB.
•
Normal: The card is an interface card and functions normally.
•
Fault: The card has not been booted or an error occurred to the card.
•
Off: The card is not powered on.
•
Illegal: The card is not supported by the software version and thus cannot start normally.
Subslot Num: Outbound interface in an ARP entry.
Sft Ver: Age timer for a dynamic ARP entry in minutes.
42
•
Specific software version: The software version of the switch.
•
NONE: No card is in the slot.
•
Mismatched: The software version does not support the card and thus cannot be uploaded.
Display Commands
display dhcp relay information all
Comware
Related ProVision
display dhcp relay information all
No equivalent ProVision software command
Displays option 82 configuration information on the DHCP relay agent.
HP Switch# display dhcp relay information all
Interface: Vlan-interface1
Status: Disable
Strategy: Replace
Format: Normal
Circuit ID format-type: HEX
Remote ID format-type: HEX
Interface: Vlan-interface10
Status: Enable
Strategy: Replace
Format: Normal
Circuit ID format-type: HEX
Remote ID format-type: HEX
Minimum Software Version: 15.10.
display dhcp relay information all
43
display dhcp relay information interface Vlan-interface <vlan-id>
Comware
Related ProVision
display dhcp relay information interface Vlan-interface
<vlan-id>
No equivalent ProVision software command
Displays option 82 configuration information on the DHCP relay agent based on vlan.
HP Switch# display dhcp relay information interface Vlaninterface 10
Interface: Vlan-interface10
Status: Enable
Strategy: Replace
Format: Normal
Circuit ID format-type: HEX
Remote ID format-type: HEX
Minimum Software Version: 15.10.
44
Display Commands
display dhcp relay statistics
Comware
Related ProVision
display dhcp relay statistics
show dhcp-relay
Displays DHCP packet statistics related to a specified or all DHCP server groups. DHCP relay
statistics identifies the UDPF_DHCP_MSG PDUs and provides the information regarding the number
and type of PDUs being received/relayed from/to client and server. It also distinguishes the type
of packets (DISCOVER, REQUEST, INFORM, DECLINE, RELEASE, BOOTPREQUEST, OFFER, ACK,
NAK) along with bad packets.
display dhcp relay statistics
45
HP Switch# display dhcp relay statistics
Bad packets received:
0
DHCP packets received from clients: 2
DHCPDISCOVER packets received: 1
DHCPREQUEST packets received:
1
DHCPINFORM packets received:
0
DHCPRELEASE packets received:
0
DHCPDECLINE packets received:
0
BOOTPREQUEST packets received: 0
DHCP packets received from servers: 2
DHCPOFFER packets received:
1
DHCPACK packets received:
1
DHCPNAK packets received:
0
BOOTPREPLY packets received:
0
DHCP packets relayed to servers: 2
DHCPDISCOVER packets relayed:
1
DHCPREQUEST packets relayed:
1
DHCPINFORM packets relayed:
0
DHCPRELEASE packets relayed:
0
DHCPDECLINE packets relayed:
0
BOOTPREQUEST packets relayed:
0
DHCP packets relayed to clients: 2
DHCPOFFER packets relayed:
1
DHCPACK packets relayed:
1
DHCPNAK packets relayed:
0
BOOTPREPLY packets relayed:
0
DHCP packets sent to servers: n/a
DHCPDISCOVER packets sent:
n/a
DHCPREQUEST packets sent:
n/a
DHCPINFORM packets sent:
n/a
DHCPRELEASE packets sent:
n/a
DHCPDECLINE packets sent:
n/a
BOOTPREQUEST packets sent:
n/a
DHCP packets sent to clients: n/a
DHCPOFFER packets sent:
n/a
DHCPACK packets sent:
n/a
DHCPNAK packets sent:
n/a
BOOTPREPLY packets sent:
n/a
Field Descriptions
The following fields are for bad packets received.
•
•
46
DHCP packets received from clients:
◦
DHCPDISCOVER packets received
◦
DHCPREQUEST packets received
◦
DHCPINFORM packets received
◦
DHCPRELEASE packets received
◦
DHCPDECLINE packets received
◦
BOOTPREQUEST packets received
DHCP packets received from servers:
◦
DHCPOFFER packets received
◦
DHCPACK packets received
Display Commands
•
•
•
•
◦
DHCPNAK packets received
◦
BOOTPREPLY packets received
DHCP packets relayed to servers:
◦
DHCPDISCOVER packets relayed
◦
DHCPREQUEST packets relayed
◦
DHCPINFORM packets relayed
◦
DHCPRELEASE packets relayed
◦
DHCPDECLINE packets relayed
◦
BOOTPREQUEST packets relayed
DHCP packets relayed to clients:
◦
DHCPOFFER packets relayed0
◦
DHCPACK packets relayed
◦
DHCPNAK packets relayed
◦
BOOTPREPLY packets relayed
DHCP packets sent to servers:
◦
DHCPDISCOVER packets sent
◦
DHCPREQUEST packets sent
◦
DHCPINFORM packets sent
◦
DHCPRELEASE packets sent
◦
DHCPDECLINE packets sent
◦
BOOTPREQUEST packets sent
DHCP packets sent to clients:
◦
DHCPOFFER packets sent
◦
DHCPACK packets sent
◦
DHCPNAK packets sent
◦
BOOTPREPLY packets sent
Operating Notes
For more information about IPv6 DHCP, see the "DHCPv6 Relay" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show dhcp-relay
DHCP Relay Agent
: Enabled
DHCP Request Hop Count Increment : Enabled
Option 82
: Disabled
Response validation
: Disabled
display dhcp relay statistics
47
Option 82 handle policy
Remote ID
: mac
: replace
DHCP Relay Statistics:
Client Requests
Server Responses
Valid
Dropped
Valid Dropped
---------- ---------- ---------- ---------0
0
0
0
DHCP Relay Option 82 Statistics:
Client Requests
Server Responses
Valid
Dropped
Valid Dropped
---------- ---------- ---------- ---------0
0
0
0
display dhcp relay statistics Field Mappings.
The Comware output does not correlate to the ProVision output.
48
Display Commands
display dhcp-snooping [ip ip_address]
Comware
Related ProVision
display dhcp-snooping [ip ip_address]
show dhcp-snooping binding
Displays the user IP-MAC address mapping entries recorded by the DHCP snooping function.
HP Switch# display dhcp-snooping
DHCP Snooping is enabled.
The client binding table for all untrusted ports.
Type : D--Dynamic , S--Static , R--Recovering
Type IP Address MAC Address
Lease
VLAN SVLAN Interface
---- ----------- --------------- ---------- ---- ----- --------S
192.168.1.1
0050-569f-2c8b
static
1
n/a
1
S
192.168.1.2
0050-569f-2c8c
static
2
n/a
9
S
192.168.1.3
0050-569f-2caa
static
3
n/a
3
S
192.168.1.4
0050-569f-2c8a
static
4
n/a
7
S
192.168.1.5
0050-569f-2c8d
static
5
n/a
5
--- 5 dhcp-snooping item(s) found ---
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snooping binding
MacAddress
IP
VLAN Interface Time left
----------------- --------------- ---- --------- --------22.22.22.22.22.22 10.0.0.1
4
B2 1600
For more information, see the latest Management and Configuration Guide for your switch.
display dhcp-snooping [ip ip_address]
49
display dhcp-snooping binding database
Comware
Related ProVision
display dhcp-snooping binding database
show dhcp-snooping
Displays the DHCP snooping binding file information.
HP Switch# display dhcp-snooping binding database
File name
: cfa0:/database.dhcp
Update interval : 10 minutes
Latest read time : n/a
Latest write time : Jul 15 2008 16:38:24
Status
: Last write succeeded.
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snooping
DHCP Snooping Information
DHCP Snooping : Yes
Enabled Vlans :
Verify MAC : Yes
Option 82 untrusted policy : drop
Option 82 Insertion : Yes
Option 82 remote-id : mac
Store lease database : Not configured
Port Trust
----- ----B1 No
B2 No
For more information, see the latest Management and Configuration Guide for your switch.
50
Display Commands
display dhcp-snooping information
Comware
Related ProVision
display dhcp-snooping information
show dhcp-snooping
Displays information about dhcp snooping when option 82 is enabled.
HP Switch# display dhcp-snooping information all
Interface: A1
Status: Enable
Strategy: Drop
Format: n/a
Remote ID format-type: HEX
User defined :
Remote ID: 0026f1-0faf00
Interface: A2
Status: Enable
Strategy: Drop
Format: n/a
Remote ID format-type: HEX
User defined:
Remote ID: 0026f1-0faf00
... (contd. for all ports)
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snooping
DHCP Snooping Information
DHCP Snooping : Yes
Enabled Vlans :
Verify MAC : Yes
Option 82 untrusted policy : drop
Option 82 Insertion : Yes
Option 82 remote-id : mac
Store lease database : Not
Port Trust
----- ----B1
No
B2
No
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
display dhcp-snooping information
51
display dhcp-snooping packet statistics
Comware
Related ProVision
display dhcp-snooping packet statistics
show dhcp-snooping statistics
Displays the statistics of the dhcp snooping packets.
HP Switch# display dhcp-snooping packet
DHCP packets received
DHCP packets send
Packets dropped due to rate limitation
Dropped invalid packets
statistics
: 2
: 0
: n/a
: 0
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snooping statistics
Packet type Action
Reason
----------- ------- ---------------------------server
client
server
server
client
client
client
client
forward
forward
drop
drop
drop
drop
drop
drop
from trusted port
to trusted port
received on untrusted port
unauthorized server
destination on untrusted port
untrusted option 82 field
bad DHCP release request
failed verify MAC check
Minimum Software Version: 15.10.
52
Display Commands
Count
--------0
0
0
0
0
0
0
0
display dhcp-snooping trust
Comware
Related ProVision
display dhcp-snooping trust
show dhcp-snooping
Displays information about trusted ports.
HP Switch(config)# display dhcp-snooping trust
DHCP Snooping is enabled.
DHCP Snooping trust becomes active.
Interface
Trusted
=========================
============
A1
Trusted
A2
Trusted
A3
Trusted
A4
Trusted
Field Descriptions
Interface: Interface
Trusted: The interface is trusted or not trusted.
Operating Notes
For more information about DHCP snooping, see the "Configuring Advanced Threat Protection"
chapter in the latest Access Security Guide for your switch.
EXAMPLE OF RELATED PROVISION SOFTWARE COMMAND OUTPUT.
HP Switch(config)# show dhcp-snooping
DHCP Snooping Information
DHCP Snooping
: Yes
Enabled Vlans
:
Verify MAC
: Yes
Option 82 untrusted policy : drop
Option 82 Insertion
: Yes
Option 82 remote-id
: mac
Store lease database : Not configured
Port Trust
----- ----B1
No
B2
No
display dhcp-snooping trust Field Mappings.
Comware
ProVision Software
DHCP snooping is enabled
DHCP Snooping (yes/no)
Interface
Port
Trusted
Trust
display dhcp-snooping trust
53
display diagnostic-information
Comware
Related ProVision
display diagnostic-information
show tech
Displays different levels of diagnostic information. This is an alias to the ProVision command show
tech and shares the same behavior.
HP Switch# show tech
show system
Status
System
System
System
and Counters - General System Information
Name
: 5400_1
Contact
:
Location
:
MAC Age Time (sec) : 300
Time Zone
: 0
Daylight Time Rule : None
Software revision
ROM Version
: K.14.XX
: K.12.12
Base MAC Addr
Serial Number
Up Time
: 23 hours Memory - Total
CPU Util (%)
: 10
Free
IP Mgmt - Pkts Rx : 759
Packet - Total
Pkts Tx : 2
Buffers Free
Lowest : 4961
Missed : 0
show flash
Image
Size(Bytes) Date
Version
-------------- -------- -----------
Minimum Software Version: 15.10.
54
Display Commands
: 001871-c42f00
: SG641SU00L
:
:
: 6750
: 5086
display dns < domain | server >
Comware
Related ProVision
display dns < domain | server >
show ip dns
show ip
Displays the current IPv4 DNS domain name suffixes and server configuration.
HP Switch# display dns domain
Type:
D:Dynamic
No.
1
S:Static
Type
S
Domain-name
atlantic.widgetcorp.net
HP Switch# display dns server
Type:
D:Dynamic
DNS Server
1
2
S:Static
Type
S
S
IP Address
10.110.34.51
10.110.34.101
Field Descriptions
No.: Sequence number.
Type: Shows the type of domain name suffix. S means a statically configured domaine name suffix.
D means a domain name suffix obtained dynamically through DHCP.
Domain-name: The domain name suffix.
DNS Server: The sequence number of the DNS server.
IP Address: The IPv4 address of the DNS server(s).
Operating Notes
The switch supports one domain suffix entry and two DNS server IP address entries.
To configure DNS operation in ProVision software, use one of the following commands:
ip dns dhcp
ip dns domain-name < name-str >
ip dns server-address priority < 1 | 2 > < ip-addr | ipv6-addr >
For more on configuring dns, refer to the “Troubleshooting” chapter in the latest Management and
Configuration Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch# show ip dns
DNS Mode
:
Domain Suffix
DHCP
: americas.hpqcorp.net
DNS Servers Configured :
---------------------Priority
DNS Server Addresses
--------------------------display dns < domain | server >
55
1.
2.
16.110.135.52
16.110.135.51
DNS Field Mappings.
56
Comware
ProVision Software
No.
n/a
DNS Server
Priority
Type
DNS Mode
Domain-name
Domain Suffix
IP Address
DNS Server Addresses
n/a
DNS Servers Configured
Display Commands
display dns domain
Comware
Related ProVision
display dns domain
show ip dns
Displays all the domain name suffixes that are appended to host names by the resolver before
sending the queries to name servers. These domain name suffixes could have been statically
configured on the switch or obtained from the DHCP server dynamically.
HP Switch# display dns domain
Type:
D:Dynamic
S:Static
No.
1
2
3
Type
S
S
S
Domain-name
hp5.com
hp.in
hp.us
Example of Related ProVision Software Command Output.
HP Switch# show ip dns
DNS Mode : DHCP
Domain Suffix : pubs.outdoors.com
DNS Servers Configured:
---------------------10.28.229.10
Priority DNS Server Addresses
-------- -------------------1 10.28.192.1
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display dns domain
57
display dns domain dynamic
Comware
Related ProVision
display dns domain dynamic
No equivalent ProVision software command
Displays all the domain name suffixes that are obtained from the DHCP server dynamically.
HP Switch# display dns domain dynamic
Type:
D:Dynamic
No.
1
2
3
Type
D
D
D
S:Static
Domain-name
hp2.net
hp3.net
hp4.net
Minimum Software Version: 15.10.
58
Display Commands
display dns ipv6 server
Comware
Related ProVision
display dns ipv6 server
show ip dns
Displays IPv6 DNS server information.
HP Switch# display dns ipv6 server
Type:
D:Dynamic S:Static
DNS Server Type IPv6 Address
(Interface Name)
1
S
1::1
2
S
FE80:1111:2222:3333:4444:5555:6666:7777
Vlan2
Field Descriptions
DNS Server: Sequence number of the DNS server, which is assigned automatically by the system,
starting from 1.
Type: Type of the DNS server. "S" represents a statically configured DNS server, and "D" represents
a DNS server obtained dynamically through DHCP or other protocols.
IPv6 Address: IPv6 address of the DNS server.
Interface Name: Interface name, which is available only for a DNS server with an IPv6 link-local
address configured.
Operating Notes
Out-of-band management and tunnel interfaces are supported.
For more information about IPv6 DNS, see the "IPv6 Diagnostic and Troubleshooting" chapter in
the latest IPv6 Configuration Guide for your switch.
display dns ipv6 server
59
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip dns
DNS Mode
: Manual
Domain Suffix
: atlantic.widgetcorp.net
DNS Servers Configured:
---------------------Priority
DNS Server Addresses
--------------------------1.
10.110.34.51
2.
10.110.34.101
display dns ipv6 server Field Mappings.
60
Comware
ProVision Software
DNS Server
DNS Servers Configured
Type
DNS Mode
IPv6 Address
DNS Server Addresses
Interface Name
n/a
Display Commands
display dot1x [interface …]display dot1x sessions [interface …]display
dot1x statistics [interface …]
Comware
Related ProVision
display dot1x [interface ...]
show dhcp-snooping binding
display dot1x sessions [interface ...]
display dot1x statistics [interface ...]
Displays information about 802.1X.
HP Switch# display dot1x
Equipment 802.1X protocol is
CHAP authentication is n/a
Proxy trap checker is n/a
Proxy logoff checker is n/a
EAD quick deploy is n/a
Configuration: Transmit Period
30 s, Handshake Period
n/a
Quiet Period
60 s, Quiet Period Timer is n/a
Supp Timeout
30 s, Server Timeout
300 s
Reauth Period
3600 s
The maximal retransmitting times
2
EAD quick deploy configuration:
EAD timeout:
n/a
The maximum 802.1X user resource number is n/a per slot
Total current used 802.1X resource number is n/a
A1 is link-up
802.1X protocol is disabled
Proxy trap checker is
n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
Periodic reauthentication is disabled
The port is not an authenticator
Authentication Mode is Auto
Port Control Type is n/a
802.1X Multicast-trigger is n/a
Mandatory authentication domain: n/a
Guest VLAN: 0
Auth-Fail VLAN: n/a
Max number of on-line users is 0
EAPOL Packet: Tx n/a, Rx n/a
Sent EAP Request/Identity Packets : 0
EAP Request/Challenge Packets: 0
EAP Request/Challenge Packets: 0
Received EAPOL Start Packets : 0
EAPOL LogOff Packets: 0
EAP Response/Identity Packets : 0
EAP Response/Challenge Packets: 0
Error Packets: 0
Controlled User(s) amount to n/a
HP Switch# display dot1x sessions
Equipment 802.1X protocol is enabled
CHAP authentication is n/a
The maximum 802.1X user resource number is n/a per slot
Total current used 802.1X resource number is n/a
A1 is link-up
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
display dot1x [interface …]display dot1x sessions [interface …]display dot1x statistics [interface …]
61
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
A2 is link-down
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
A3 is link-down
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
HP Switch# display dot1x sessions
Equipment 802.1X protocol is enabled
CHAP authentication is n/a
The maximum 802.1X user resource number is n/a per slot
Total current used 802.1X resource number is n/a
A1 is link-up
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
EAPOL Packet: Tx n/a, Rx n/a
Sent EAP Request/Identity Packets : 0
EAP Request/Challenge Packets: 0
EAP Request/Challenge Packets: 0
Received EAPOL Start Packets : 0
EAPOL LogOff Packets: 0
EAP Response/Identity Packets : 0
EAP Response/Challenge Packets: 0
Error Packets: 0
Controlled User(s) amount to n/a
A2 is link-down
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
EAPOL Packet: Tx n/a, Rx n/a
Sent EAP Request/Identity Packets : 0
EAP Request/Challenge Packets: 0
EAP Request/Challenge Packets: 0
Received EAPOL Start Packets : 0
EAPOL LogOff Packets: 0
EAP Response/Identity Packets : 0
EAP Response/Challenge Packets: 0
Error Packets: 0
Controlled User(s) amount to n/a
Example of Related ProVision Software Command Output.
HP Switch# show dhcp-snooping binding
62
Display Commands
MacAddress
IP
VLAN Interface Time left
----------------- -------- ----- --------- --------22.22.22.22.22.22 10.0.0.1
4
B2
1600
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
display dot1x [interface …]display dot1x sessions [interface …]display dot1x statistics [interface …]
63
display dot1x [interface]
Comware
Related ProVision
display dot1x [interface interface-list]
show port-access authenticator [config| statistics
| session counters]
display dot1x sessions [interface interface-list]
display dot1x statistics [interface interface-list]
Displays information about 802.1X.
If you specify neither the sessions keyword nor the statistics keyword, the command displays all
information about 802.1X, including session information, statistics, and configurations.
64
Display Commands
HP Switch(config)# display dot1x interface A1
Equipment 802.1X protocol is
CHAP authentication is n/a
Proxy trap checker is n/a
Proxy logoff checker is n/a
EAD quick deploy is n/a
Configuration: Transmit Period 30 s, Handshake Period n/a
Quiet Period 60 s, Quiet Period Timer is n/a
Supp Timeout 30 s, Server Timeout 300 s
Reauth Period 3600 s
The maximal retransmitting times 2
EAD quick deploy configuration:
EAD timeout: n/a
The maximum 802.1X user resource number is n/a per slot
Total current used 802.1X resource number is n/a
A1 is link-up
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
Periodic reauthentication is disabled
The port is not an authenticator
Authentication Mode is Auto
Port Control Type is n/a
802.1X Multicast-trigger is n/a
Mandatory authentication domain: n/a
Guest VLAN: 0
Auth-Fail VLAN: n/a
Max number of on-line users is 0
EAPOL Packet: Tx n/a, Rx n/a
Sent EAP Request/Identity Packets : 0
EAP Request/Challenge Packets: 0
EAP Request/Challenge Packets: 0
Received EAPOL Start Packets : 0
EAPOL LogOff Packets: 0
EAP Response/Identity Packets : 0
EAP Response/Challenge Packets: 0
Error Packets: 0
Controlled User(s) amount to n/a
display dot1x [interface]
65
HP Switch(config)# display dot1x sessions
Equipment 802.1X protocol is enabled
CHAP authentication is n/a
The maximum 802.1X user resource number is n/a per slot
Total current used 802.1X resource number is n/a
A1 is link-up
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
A2 is link-down
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
A3 is link-down
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
Controlled User(s) amount to n/a
66
Display Commands
HP Switch(config)# display dot1x statistics
Equipment 802.1X protocol is enabled
CHAP authentication is n/a
The maximum 802.1X user resource number is n/a per slot
Total current used 802.1X resource number is n/a
A1 is link-up
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
EAPOL Packet: Tx n/a, Rx n/a
Sent EAP Request/Identity Packets : 0
EAP Request/Challenge Packets: 0
EAP Request/Challenge Packets: 0
Received EAPOL Start Packets : 0
EAPOL LogOff Packets: 0
EAP Response/Identity Packets : 0
EAP Response/Challenge Packets: 0
Error Packets: 0
Controlled User(s) amount to n/a
A2 is link-down
802.1X protocol is disabled
Proxy trap checker is n/a
Proxy logoff checker is n/a
Handshake is n/a
Handshake secure is n/a
802.1X unicast-trigger is n/a
EAPOL Packet: Tx n/a, Rx n/a
Sent EAP Request/Identity Packets : 0
EAP Request/Challenge Packets: 0
EAP Request/Challenge Packets: 0
Received EAPOL Start Packets : 0
EAPOL LogOff Packets: 0
EAP Response/Identity Packets : 0
EAP Response/Challenge Packets: 0
Error Packets: 0
Controlled User(s) amount to n/a
Field Descriptions
Equipment 802.1X protocol is enabled: Specifies whether 802.1X is enabled globally.
CHAP authentication is enabled: Specifies whether CHAP authentication is enabled.
Transmit Period: Username request timeout timer in seconds.
Handshake Period: Handshake timer in seconds.
Reauth Period: Periodic re-authentication timer in seconds.
Quiet Period: Quiet timer in seconds.
Quiet Period Timer is disabled: Status of the quiet timer. In this example, the quiet timer is enabled.
Supp Timeout: Client timeout timer in seconds.
Server Timeout: Server timeout timer in seconds.
display dot1x [interface]
67
The maximal retransmitting times: Maximum number of attempts for sending an authentication
request to a client.
The maximum 802.1X user resource number per slot: Maximum number of concurrent 802.1X
user per card.
Total current used 802.1X resource number: Total number of online 802.1X users.
GigabitEthernet3/0/1 is link-up: Status of the port. In this example, GigabitEthernet 3/0/1 is up.
802.1X protocol is disabled: Specifies whether 802.1X is enabled on the port.
Handshake is disabled: Specifies whether handshake is enabled on the port.
Handshake secure is disabled: Specifies whether handshake security is enabled on the port.
802.1X unicast-trigger is disabled: Specifies whether unicast trigger is enabled on the port.
Periodic reauthentication is disabled: Specifies whether periodic online user reauthentication is
enabled on the port.
The port is an authenticator: Role of the port.
Authenticate Mode is Auto: Authorization state of the port.
Port Control Type is Mac-based: Access control method of the port.
802.1X Multicast-trigger is enabled: Specifies whether the 802.1X multicasttrigger function is
enabled.
Mandatory authentication domain: Mandatory authentication domain on the port.
Guest VLAN: 802.1X guest VLAN configured on the port. NOT configured is displayed if no guest
VLAN is configured.
Auth-fail VLAN: Auth-Fail VLAN configured on the port. NOT configured is displayed if no Auth-Fail
VLAN is configured.
Max number of on-line users: Maximum number of concurrent 802.1X users on the port.
EAPOL Packet: Number of sent (Tx) and received (Rx) EAPOL packets.
Sent EAP Request/Identity Packets: Number of sent EAP-Request/Identity packets.
EAP Request/Challenge Packets: Number of sent EAP-Request/Challenge packets.
EAP Success Packets: Number of sent EAP Success packets.
Fail Packets: Number of sent EAP-Failure packets.
Received EAPOL Start Packets: Number of received EAPOL-Start packets.
EAPOL LogOff Packets: Number of received EAPOL-LogOff packets.
EAP Response/Identity Packets: Number of received EAP-Response/Identity packets.
EAP Response/Challenge Packets: Number of received EAP-Response/Challenge packets.
Error Packets: Number of received error packets.
Controlled User(s) amount: Number of authenticated users on the port.
Operating Notes
For more on switch 802.1X operation, refer to the "Configuring Port-based and User-based Access
Control (802.1X)" chapter in the latest Access Security Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show port-access authenticator config
Port Access Authenticator Configuration
Port-access authenticator activated [No] : Yes
Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No
68
Display Commands
Port
---1
2
...
|
|
+
|
|
Re-auth
Period
------No
No
Access
Control
-------Auto
Auto
Max
Reqs
----2
2
Quiet
Period
------60
60
TX
Timeout
-------30
30
Supplicant
Timeout
---------30
30
Server
Timeout
-------30
30
Cntrl
Dir
----both
in
HP Switch(config)# show port-access authenticator session-counters
Port Access Authenticator Session Counters
Port-access authenticator activated [No] : Yes
Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No
Session
Session
Port Frames In Frames Out Time(sec.) Status
User
---- ---------- ----------- ----------- ----------- ------2
45623
45623
20
in-progress bert
display dot1x [interface]
69
HP Switch(config)# show port-access authenticator statistics
Port Access Authenticator Statistics
Port-access authenticator activated [No] : Yes
Allow RADIUS-assigned dynamic (GVRP) VLANs [No] : No
Source
Port MAC address
---- ------------2
001560-b3ea48
TX
ReqId
-----1
TX
Req
----0
RX
Start
-----0
RX
Logoff
------0
RX
RespId
------0
RX
Resp
----0
RX
Errors
------0
display dot1x Field Mappings.
70
Comware
ProVision Software
Equipment 802.1X protocol is enabled
Port-access authenticator activated (yes/no)
CHAP authentication is enabled
n/a
Transmit Period
TX Timeout Handshake Period
Handshake Period
n/a
Reauth Period
Re-auth Period
Quiet Period
Quiet Period
Quiet Period Timer is disabled
n/a
Supp Timeout
Supplicant Timeout
Server Timeout
Server Timeout
The maximal retransmitting times
Max Reqs
The maximum 802.1X user resource number per slot
n/a
Total current used 802.1X resource number
n/a
GigabitEthernet3/0/1 is link up
n/a
802.1X protocol is disabled
Port-access authenticator activated (yes/no)
Handshake is disabled
n/a
802.1X unicast-trigger is disabled
n/a
Periodic reauthentication is disabled
Re-auth Period
The port is an authenticator
n/a
Authenticate Mode is Auto
Access Control
Port Control Type is Mac-based
n/a
802.1X Multicast-trigger is enabled
n/a
Mandatory authentication domain
n/a
Guest VLAN
n/a
Auth-fail VLAN
n/a
Max number of on-line users
n/a
EAPOL Packet
n/a
Sent EAP Request/Identity Packets
TX ReqId
EAP Request/Challenge Packets
TX Req
EAP Success Packets
n/a
Display Commands
Comware
ProVision Software
Fail Packets
n/a
Received EAPOL Start Packets
RX Start
EAPOL Logoff Packets
RX Logoff
EAP Response/Identity Packets
RX RespId
EAP Response/Challenge Packets
RX Resp
Error Packets
RX Errors
Controlled User(s) amount
n/a
display dot1x [interface]
71
display environment
Comware
Related ProVision
display environment
show system temperature
Displays the temperature information, including the current temperature and temperature thresholds
of cards.
HP Switch# display environment
System temperature information (degree centigrade)
--------------------------------------------------------Slot Sensor Temperature LowerLimit WarningLimit AlarmLimit ShutdownLimit
n/a Sys-1
29C
n/a
57C
n/a
n/a
Field Descriptions
Slot: Slot number of the card (standalone mode); slot number of a card on the specified member
switch in the format of member ID/slot number (IRF mode)
Sensor: Temperature sensor:
•
hotspot: Hotspot temperature sensor
•
inflow: Inflow temperature sensor
•
outflow: Outflow temperature sensor
Temperature: Current temperature
Lower limit: Lower limit of temperature
WarningLimit: Upper limit of temperature for warning
AlarmLimit: Upper limit of temperature for alarming
ShutdownLimit: Upper limit of temperature for shutting down the switch (currently not supported)
Example of Related ProVision Software Command Output.
HP Switch# show system temperature
System Air Temperatures
#
|Current Temp | Max Temp| Min Temp | Threshold| OverTemp
------+------------+----------+---------+-----------+-------Sys-1 |
31C
|
37C |
29C |
57C |
NO
For more information, see the latest Management and Configuration Guide for your switch.
72
Display Commands
display fan
Comware
Related ProVision
display fan
show system fans
Displays the operating state of built-in fans.
HP Switch# display fan
Fan 1 State: Fan Ok
Example of Related ProVision Software Command Output.
HP Switch(config)# show system fans
Fan Information
Num
| State
| Failures
-------+-------------+---------Sys-1 | Fan OK
| 0
0 / 1 Fans in Failure State
0 / 1 Fans have been in Failure State
Operating Notes
ProVision uses HP format for printing the fan state.
For more information, see the latest Management and Configuration Guide for your switch.
display fan
73
display fib <ip-address>
Comware
Related ProVision
display fib <ip-address>
show ip route
Displays FIB entries that match the specified destination IP address.
If no mask or mask length is specified, the FIB entry that matches the destination IP address and
has the longest mask will be displayed; if the mask is specified, the FIB entry that exactly matches
the specified destination IP address will be displayed.
HP Switch# display fib
Destination count: n/a
FIB entry count: n/a
Flag:
U:Useable
G:Gateway
H:Host
R:Relay
Destination/MASK
Nexthop
0.0.0.0/0
10.0.8.1
10.0.8.0/21
DEFAULT_VLAN
127.0.0.0/8
reject
127.0.0.1/32
lo0
0.0.0.0/0
lo0
B:Blackhole
Flag
n/a
n/a
n/a
n/a
n/a
D:Dynamic
OutInterface
VLAN1
VLAN1
S:Static
InnerLabel
n/a
n/a
n/a
n/a
n/a
Token
n/a
n/a
n/a
n/a
n/a
Field Descriptions
Destination count: Total number of destination addresses.
Destination/Mask: Destination address/length of mask.
Nexthop: Address of next hop.
Flag: Flags of routes:
•
“U”—Usable route
•
“G”—Gateway route
•
“H”—Host route
•
“B”—Blackhole route
•
“D”—Dynamic route
◦
“S”—Static route
◦
"R"—Relay route
OutInterface: Outbound interface.
InnerLabel: Inner label.
Token: LSP index number.
Operating Notes
Values for “Nexthop” and “Outinterface” will be the same as the Gateway and VLAN of the output
for show ip route.
For more information, see the “IP Routing Features” chapter in the latest Multicast and Routing
Guide for your switch.
Minimum Software Version: 15.11.
Example of Related ProVision Software Command Output.
74
Display Commands
HP Switch(config)# show ip route
IP Route Entries
Destination
Gateway
VLAN Type
Sub-Type
Metric
Dist.
----------------- --------------- ---- --------- ---------- -------- ----10.10.10.1/32
10.10.12.1
connected
1
0
display fib <ip-address>
75
display fips status
Comware
Related ProVision
display fips status
show secure-mode
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays FIPS state. By default, the FIPS mode is disabled.
HP Switch# display fips status
FIPS mode is disabled
or
HP Switch# display fips status
FIPS mode is enabled
Example of Related ProVision Software Command Output.
HP Switch# show secure-mode
Level: Standard
or
HP Switch# display fips status
FIPS mode is enabled
For more information, see the latest Access Security Guide for your switch.
76
Display Commands
display garp statistics interface <port_list>
Comware
Related ProVision
display garp statistics interface <port_list>
show gvrp
Displays GVRP transmitted, received and discarded frames in a specified VLAN on a port.
HP Switch# display garp statistics interface a2
GARP statistics on port A2
Number of GVRP Frames Received
: 79
Number of GVRP Frames Transmitted : 67
Number of Frames Discarded
: 0
Example of Related ProVision Software Command Output.
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256
Primary VLAN : DEFAULT_VLAN
GVRP Enabled [No] : Yes
Port Type
---- -------1
10/100TX
2
10/100TX
3
10/100TX
4
10/100TX
5
10/100TX
6
10/100TX
. . . . . .
| Unknown VLAN Join Leave Leaveall
+ ------------ ----- ----- -------|
Learn
20
300
1000
|
Learn
20
300
1000
|
Learn
20
300
1000
|
Learn
20
300
1000
|
Learn
20
300
1000
|
Learn
20
300
1000
For more information, see the latest Advanced Traffic Management Guide for your switch.
display garp statistics interface <port_list>
77
display garp timer interface <port_list>
Comware
Related ProVision
display garp timer interface <port_list>
show gvrp
Display GARP timer in a specified port.
HP Switch# display garp timer interface a2
GARP timers on port A2
Garp Join Time
: 20 centisecounds
Garp Leave Time : 300 centisecounds
Garp LeaveAll Time : 1000 centisecounds
Garp Hold Time
: (n/a)
Example of Related ProVision Software Command Output.
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256
Primary VLAN : DEFAULT_VLAN
GVRP Enabled [No] : Yes
Port Type
---- -------1
10/100TX
2
10/100TX
3
10/100TX
4
10/100TX
5
10/100TX
6
10/100TX
. . . . . .
| Unknown VLAN Join Leave Leaveall
+ ------------ ----- ----- -------|
Learn
20
300
1000
|
Learn
20
300
1000
|
Learn
20
300
1000
|
Learn
20
300
1000
|
Learn
20
300
1000
|
Learn
20
300
1000
Operating Notes
Depending on the device, ProVision displays port numbers as A1, B1, etc. or 1,2, etc. or 1/1,
2/1, etc.
Any display output field not supported in Provsion is displayed as n/a.
For more information, see the latest Advanced Traffic Management Guide for your switch.
78
Display Commands
display gvrp state interface <port_list> vlan <vlan-id>
Comware
Related ProVision
display gvrp state interface <port_list> vlan <vlan-id>
show gvrp
Displays GVRP state machines in a specified VLAN on a port.
HP Switch# display gvrp state interface a2 vlan 2
GVRP state of VLAN 2 on port a2
Applicant state machine : QA
Registrar state machine : MTR
Field Descriptions
Applicant state machine: The Applicant state machine handles attribute declarations. Its state can
be VA, AA, QA, LA, VP, AP, QP, VO, AO, QO, LO, VON, AON, and QON. Each state consists
of two or three letters with the following meanings:
•
The first letter indicates the state: V for Very anxious, A for Anxious, Q for Quiet, and L for
Leaving.
•
The second letter indicates the membership state: A for Active member, P for Passive member,
O for Observer.
•
The third letter N (if any) stands for Non-participant.
For example, VP indicates "Very anxious, Passive member".
Registrar state machine:The Registrar state machine records the registration of attributes declared
by other participants. Its state can be INN, LV, L3, L2, L1, MT, INR, LVR, L3R, L2R, L1R, MTR, INF,
LVF, L3F, L2F, L1F, and MTF. Each state consists of two or three letters/numbers with the following
meanings:
•
The first two letters/numbers indicate the state: IN stands for In; LV, L3, L2, and L1 all stand
for Leaving, and L3, L2, L1 are three sub-states of LV; MT stands for Empty
•
The third letter indicates the registration mode: N (or the third letter being absent) for normal
registration, R for Registration fixed, and F for Registration forbidden.
For example, MTR stands for "Empty, Registration fixed", indicating the fixed registration mode in
Empty state.
Example of Related ProVision Software Command Output.
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256
Primary VLAN : DEFAULT_VLAN
GVRP Enabled [No] : Yes
Port Type
| Unknown VLAN Join Leave Leaveall
---- -------- + ------------ ----- ----- -------1
10/100TX |
Learn
20
300
1000
2
10/100TX |
Learn
20
300
1000
3
10/100TX |
Learn
20
300
1000
4
10/100TX |
Learn
20
300
1000
5
10/100TX |
Learn
20
300
1000
6
10/100TX |
Learn
20
300
1000
. . . . . .
For more information, see the latest Advanced Traffic Management Guide for your switch.
display gvrp state interface <port_list> vlan <vlan-id>
79
display gvrp statistics
Comware
Related ProVision
display gvrp statistics
show gvrp
Displays the GVRP statistics of all tagged ports.
HP Switch# display gvrp statistics
GVRP statistics on port A1
GVRP Status
: Disabled
GVRP Running
: YES
GVRP Failed Registrations : n/a
GVRP Last Pdu Origin
: n/a
GVRP Registration Type
: Normal
Field Descriptions
GVRP Status: Indicates whether GVRP is enabled or disabled
GVRP Running: Indicates whether GVRP is running
GVRP Failed Registrations: Indicates the number of GVRP registration failures
GVRP Last Pdu Origin: Indicates the source MAC address in the last GVRP PDU
GVRP Registration Type: Indicates the GVRP registration mode (fixed, forbidden, or normal) on the
port
Example of Related ProVision Software Command Output.
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256
Primary VLAN : DEFAULT_VLAN
GVRP Enabled [No] : Yes
Port Type
| Unknown VLAN Join Leave Leaveall
---- -------- + ------------ ----- ----- -------1
10/100TX |
Learn
20
300
1000
2
10/100TX |
Learn
20
300
1000
3
10/100TX |
Learn
20
300
1000
4
10/100TX |
Learn
20
300
1000
5
10/100TX |
Learn
20
300
1000
6
10/100TX |
Learn
20
300
1000
. . . . . .
For more information, see the latest Advanced Traffic Management Guide for your switch. Comware
Related ProVision display gvrp statistics show gvrp
80
Display Commands
display gvrp status
Displays the global enable/disable state of GVRP.
Comware
Related ProVision
display gvrp status
show gvrp
HP Switch# display gvrp status
GVRP is enabled
Operating Notes
To enable and control GVRP operation in ProVision software, use the following commands:
gvrp
interface < port-list > unknown-vlans < learn | block | disable >
ProVision software also supports GVRP configuration and status monitoring by using the Menu
interface.
For more on GVRP operation, refer to the chapter titled “GVRP” in the latest Advanced Traffic
Management Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
GVRP disabled:
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256
Primary VLAN : DEFAULT_VLAN
GVRP Enabled [No] : No
GVRP enabled:
HP Switch# show gvrp
GVRP support
Maximum VLANs to support [256] : 256
Primary VLAN : DEFAULT_VLAN
GVRP Enabled [No] : Yes
Port
---A1
A2
A3
Type
--------100/1000T
100/1000T
100/1000T
|
+
|
|
|
Unknown VLAN
-----------Learn
Learn
Learn
Join
----20
20
20
Leave
----300
300
300
Leaveall
-------1000
1000
1000
20
300
1000
.
.
.
A24
100/1000T | Learn
display gvrp status
81
display gvrp vlan-operation interface interface-type interface-number
Comware
Related ProVision
display gvrp vlan-operation interface interface-type
interface-number
No equivalent ProVision software command
Displays information about dynamic VLAN operations on a port.
HP Switch# display gvrp vlan-operation interface a3
Dynamic VLAN operations on port A3
Operations
Operations
Operations
Operations
of
of
of
of
creating VLAN
deleting VLAN
adding VLAN to TRUNK
deleting VLAN from TRUNK
Minimum Software Version: 15.10.
82
Display Commands
:
:
:
:
none
none
none
none
display history-command
Comware
Related ProVision
display history-command
show history
Displays the last 25 commands executed on the switch CLI, including commands entered incorrectly.
The command listing begins with the oldest command in the sequence and ends with the most
recent command executed (excluding the display history-command itself).
HP Switch# display history-command
25
display dns domain
24
display gvrp status
23
display gvrp status
22
gvrp helpp
21
gvrp help
20
gvrp
19
display gvrp status
.
.
.
2
display ip community-list
1
display ip as-path
Operating Notes
The ProVision software show history command output is identical to the Comware display
history-command output.
Minimum Software Version: 15.08.
display history-command
83
display hwtacacs
Comware
Related ProVision
display hwtacacs
show tacacs
Displays the configuration information or statistics of HWTACACS schemes. This command is
available only in manager mode.
HP Switch# display hwtacacs
------------------------------------------------------------HWTACACS-server template name
: n/a
Primary-authentication-server
: 1.2.3.4:n/a
VPN instance
: n/a
Primary-authorization-server
: 1.2.3.4:n/a
VPN instance
: n/a
Primary-accounting-server
: 1.2.3.4:n/a
VPN instance
: n/a
Secondary-authentication-server
: 6.7.8.9:n/a
VPN instance
: n/a
Secondary-authorization-server
: 6.7.8.9:n/a
VPN instance
: n/a
Secondary-accounting-server
: 6.7.8.9:n/a
VPN instance
: n/a
Current-authentication-server
: 1.2.3.4:n/a
VPN instance
: n/a
Current-authorization-server
: 1.2.3.4:n/a
VPN instance
: n/a
Current-accounting-server
: 1.2.3.4:n/a
VPN instance
: n/a
Nas-IP address
: n/a
key authentication
: authentication
key authorization
: authentication
key accounting
: authentication
Nas-IP address
: n/a
VPN instance
: n/a
Quiet-interval(min)
: n/a
Realtime-accounting-interval(min) : n/a
Response-timeout-interval(sec)
: 5
Acct-stop-PKT retransmit times
: n/a
Username format
: n/a
Data traffic-unit
: n/a
Packet traffic-unit
: n/a
------------------------------------------------------------Total 1 HWTACACS scheme(s).
84
Display Commands
Example of Related ProVision Software Command Output.
HP Switch# show tacacs
Status and Counters - TACACS Information
Timeout : 5
Source IP Selection : Configured IP Interface
Encryption Key :
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
display hwtacacs
85
display igmp group
Comware
Related ProVision
display igmp group
show ip igmp groups
Displays IGMP group address, uptime, and expiry information. If no IGMP groups are detected,
returns the system prompt.
HP Switch# display igmp group
Total 1 IGMP Group(s).
Interface group report information
Vlan-interface1(15.255.134.111):
Total 1 IGMP Group reported
Group Address Last Reporter UpTime
Expires
10.255.215.190 10.125.103.197 00:04:22 00:03:38
Field Descriptions
Vlan-interfaceN: IP address of a VLAN on which IGMP is running.
Group Address: Multicast group address.
Last Reporter: Address of the last host that reported its membership for this multicast group.
UpTime: Length of time since the multicast group was reported.
Expires: Remaining time of the multicast group, where “off” means that the multicast group never
times out.
Operating Notes
To enable IGMP operation in ProVision software, use the following command from the context of
a VLAN on which you want to enable IGMP:
ip igmp
For more on IGMP operation in ProVision software, refer to the chapter titled “Multimedia Traffic
Control with IP Multicast (IGMP)” in the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch# show ip igmp groups
IGMP Group Address Information
VLAN ID Group Address
Expires
UpTime
Last Reporter
| Type
------- --------------- ------------- ------------- --------------- + -----1
10.255.215.190 0h 0m 27s
1h 22m 37s
10.125.103.197 | Filter
IGMP Field Mappings.
86
Comware
ProVision Software
Vlan-interfaceN
VLAN ID
Group Address
Group Address
Expires
Expires
Uptime
UpTime
Last Reporter
Last Reporter
n/a
Type
Display Commands
display igmp group interface vlan-interface <vid>
Comware
Related ProVision
display igmp group interface vlan-interface <vid>
show ip igmp vlan <vid>
Displays information about dynamically joined IGMP multicast groups.
HP Switch# display igmp group interface vlan-interface 30
Vlan-interface30(75.1.30.1):
Total 5 IGMP Groups reported
Group Address Last Reporter UpTime
Expires
239.1.1.1
75.1.30.10
5d 17:48:41 00:03:13
239.1.1.2
75.1.30.10
5d 17:48:41 00:03:13
239.1.1.3
75.1.30.10
5d 17:48:41 00:03:13
239.1.1.4
75.1.30.10
5d 17:48:41 00:03:13
239.1.1.5
75.1.30.10
5d 17:48:41 00:03:13
Field Descriptions
Group: Multicast group address
Last reporter: Address of the last host that reported its membership for this multicast group
Uptime: Length of time since the multicast group was reported
Expires: Remaining time of the multicast group
Example of Related ProVision Software Command Output.
HP Switch# show ip igmp vlan 30
IGMP Service Protocol Info
Total VLANs with IGMP enabled
: 2
Current count of multicast groups joined
: 5
IGMP Filter Unknown Multicast: Disabled
IGMP Filter Unknown Multicast Status: Disabled
VLAN ID : 30
VLAN Name : VLAN30
IGMP version : 2
Querier Address [this switch] : 75.1.30.1
Querier Port :
Querier UpTime : 5d 18h 28m 35s
Querier Expiration Time : 0h 0m 6s
Active Group Addresses Type Expires Ports Reports Queries
---------------------- ---- ------- ----- -------- -------239.1.1.1
Filter
0h 2m 28s
A2
3956
0
239.1.1.2
Filter
0h 2m 28s
A2
3956
0
239.1.1.3
Filter
0h 2m 27s
A2
3956
0
239.1.1.4
Filter
0h 2m 27s
A2
3956
0
239.1.1.5
Filter
0h 2m 27s
A2
3956
0
Operating Notes
Comware displays a list of configured vlans in the tab help. ProVision does not display dynamic
help text such as this.
Comware displays an error for Invalid vlan interface. ProVision accepts the input, a validation is
done later and an error is displayed.
For more information, see the latest Multicast and Routing Guide for your switch.
display igmp group interface vlan-interface <vid>
87
display igmp group interface vlan-interface <vlan-id> static
Comware
Related ProVision
display igmp group interface vlan-interface static
No equivalent ProVision software command
Displays information regarding statically joined IGMP multicast groups.
HP Switch# display igmp group interface Vlan-interface 400 static
Static join group information of VPN-Instance: public net
Total 21 entries
Total 6 entries matched
Group Address
225.1.4.6
239.4.4.1
239.4.4.2
239.4.4.3
239.4.4.4
239.4.5.6
Source Address
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Expires
never
never
never
never
never
never
Field Descriptions
igmp: IGMP status and configuration information
group: Information about group members
interface: Specify interface
Vlan-interface: VLAN interface
VLAN-ID: VLAN interface
static: Static group information
88
Display Commands
display igmp group interface vlan-interface <vlan-id> verbose
Comware
Related ProVision
display igmp group interface vlan-interface <vlan-id> verbose
No equivalent ProVision software command
Displays detailed information about IGMP multicast groups in a particular interface.
HP Switch# display igmp group interface Vlan-interface 400
verbose
Vlan-interface400(192.168.9.2):
Total 5 IGMP Groups reported
Group: 225.1.5.4
Uptime: 00:07:19
Expires: 00:01:43
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry: off
Group: 239.4.4.4
Uptime: 00:07:19
Expires: 00:01:38
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry: off
Group: 239.9.9.9
Uptime: 00:07:19
Expires: 00:01:37
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry: off
Group: 239.9.99.99
Uptime: 00:07:19
Expires: 00:01:41
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry: off
Group: 239.99.99.99
Uptime: 00:07:19
Expires: 00:01:37
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry: off
Minimum Software Version: 15.10.
display igmp group interface vlan-interface <vlan-id> verbose
89
display igmp group port-info
Comware
Related ProVision
display igmp group port-info vlan <vid>
show ip igmp vlan <vid>
Displays Layer 2 port information of IGMP groups, including both dynamic and static Layer 2 port
entries.
HP Switch# display igmp group port-info vlan 5
Total 2 IP Group(s).
Total n/a IP Source(s).
Total n/a MAC Group(s).
Port flags: D-Dynamic port, S-Static port, C-Copy port
Subvlan flags: R-Real VLAN, C-Copy VLAN
Vlan(id):5.
Total 2 IP Group(s).
Total n/a IP Source(s).
Total n/a MAC Group(s).
Router port(s):total 2 port(s).
F23 (D)
F24 (D)
IP group(s):the following ip group(s) match to one mac group.
IP group address:239.4.4.4
(0.0.0.0, 239.4.4.4):
Host port(s):total 1 port(s).
F23 (D)
MAC group(s):
MAC group address: n/a
Host port(s):total n/a port(s).
IP group(s):the following ip group(s) match to one mac group.
IP group address:239.14.14.14
(0.0.0.0, 239.14.14.14):
Host port(s):total 1 port(s).
F23 (D)
MAC group(s):
MAC group address: n/a
Host port(s):total n/a port(s).
Field Descriptions
Total 1 IP Group(s): Total number of IP multicast groups.
Total 1 IP Source(s): Total number of IP multicast sources.
Total 1 MAC Group(s): Total number of MAC multicast groups.
Port flags: D-Dynamic port, S-Static port, C-Copy port: Port flags: D for a dynamic port, S for a
static port, and C for a port copied from a (*, G) entry to an (S, G) entry.
Subvlan flags: R-Real VLAN, C-Copy VLAN: Sub-VLAN flags: R for a real egress sub- VLAN under
the current entry, and C for a sub-VLAN copied from a (*, G) entry to an (S, G) entry.
Router port(s): Number of router ports.
Router port unit board: Mask indicating a board with a router port residing on it.
(hh:mm:ss): Remaining time of the aging timer for the dynamic member port or router port:
90
•
In standalone mode, to display the remaining life of a non-aggregation port that does not
belong to the main board, you must specify the number of the slot where the corresponding
card resides by using slot slot-number. This is not required for an aggregation port.
•
In IRF mode, to display the remaining life of a non-aggregation port that does not belong to
the main board, you must specify the member ID of the IRF member device and the slot number
Display Commands
of the card with chassis chassis-number slot slot-number. For an aggregation port, you do not
need to do this.
Operating Notes
Since ProVision switches do not need anything to be configured globally to enable igmp, no error
message is displayed for a display command if igmp is not enabled. For more information on
IGMP operation, see the "Multimedia Traffic Control with IP Multicast (IGMP)" chapter in the latest
Advanced Traffic Management Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip igmp vlan 1
IGMP Service Protocol Info
Total VLANs with IGMP enabled
: 30
Current count of multicast groups joined
VLAN ID : 2
VLAN Name : VLAN2
IGMP version : 2
Querier Address : 10.255.128.2
Querier Port : A1
Querier UpTime : 1h 51m 59s
Querier Expiration Time : 2min 5sec
Ports with multicast routers: A1, A5-A6
Active Group Addresses
---------------------226.0.6.7
226.0.6.8
Type
---------Filter
Standard
: 20
Expires
--------------2min 5sec
3min 20sec
Ports
---------A1
A2
Reports
------10
20
Queries
------10
20
display igmp group port-info Field Mappings.
Comware
ProVision Software
Total 1 IP Group(s)
n/a
Total 1 IP Source(s)
n/a
Total 1 MAC Group(s)
n/a
Port Flags
n/a
Subvlan Flags
n/a
Router port(s)
Ports with multicast routers
(hh:mm:ss)
Querier Expiration Time
IP group address
Active Group Addresses
MAC group address
n/a
Attribute
n/a
Host port unit board
n/a
Host port(s)
n/a
display igmp group port-info
91
display igmp group static
Comware
Related ProVision
display igmp group static
show ip igmp vlan <vid>
Displays the information regarding statically joined IGMP multicast groups.
HP Switch# display igmp group static
Static join group information
Total 19 entries
Group Address
225.1.1.1
225.1.1.5
225.1.4.1
225.1.5.4
225.4.4.1
225.4.4.2
225.4.4.3
225.4.4.4
225.5.5.1
225.5.5.2
225.5.5.3
225.5.5.4
225.5.5.5
225.44.46.46
225.44.46.46
225.44.46.46
225.145.145.145
225.145.145.145
225.145.145.145
Source Address
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Interface Expires
Vlan1
never
Vlan1
never
Vlan4
never
Vlan5
never
Vlan4
never
Vlan4
never
Vlan4
never
Vlan4
never
Vlan5
never
Vlan5
never
Vlan5
never
Vlan5
never
Vlan5
never
Vlan1
never
Vlan4
never
Vlan5
never
Vlan1
never
Vlan4
never
Vlan5
never
Field Descriptions
Group: Multicast group address
Expires: Remaining time of the multicast group
Example of Related ProVision Software Command Output.
HP Switch# show ip igmp vlan 1
IGMP Service Protocol Info
Total VLANs with IGMP enabled : 30
Current count of multicast groups joined : 20
VLAN ID : 2
VLAN Name : VLAN2
IGMP version : 2
Querier Address : 10.255.128.2
Querier Port : A1
Querier UpTime : 1h 51m 59s
Querier Expiration Time : 2min 5sec
Ports with multicast routers: A1, A5-A6
Active Group Addresses
---------------------226.0.6.7
226.0.6.8
Type
----Filter
Standard
Expires
------2min 5sec
3min 20sec
Ports
----A1
A2
Reports Queries
-------- ------10
10
20
20
For more information, see the latest Multicast and Routing Guide for your switch.
92
Display Commands
display igmp group verbose
Comware
Related ProVision
display igmp group verbose
No equivalent ProVision software command
Displays detailed information about IGMP multicast groups.
HP Switch# display igmp group verbose
Interface group report information
Vlan-interface400(192.168.9.2):
Total 5 IGMP Groups reported
Group: 225.1.5.4
Uptime: 00:00:16
Expires: 00:01:54
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry:
Group: 239.4.4.4
Uptime: 00:00:16
Expires: 00:01:54
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry:
Group: 239.9.9.9
Uptime: 00:00:16
Expires: 00:01:54
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry:
Group: 239.9.99.99
Uptime: 00:00:16
Expires: 00:01:54
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry:
Group: 239.99.99.99
Uptime: 00:00:16
Expires: 00:01:54
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry:
off
off
off
off
off
Minimum Software Version: 15.10.
display igmp group verbose
93
display igmp group x.x.x.x static
Comware
Related ProVision
display igmp group x.x.x.x static
show ip igmp vlan <vid>
Displays information regarding statically joined IGMP multicast groups.
HP Switch# display igmp group 225.44.46.46 static
Static join group information
Total 19 entries
Total 3 entries matched
Group Address
225.44.46.46
225.44.46.46
225.44.46.46
Source Address
0.0.0.0
0.0.0.0
0.0.0.0
Interface
Vlan1
Vlan4
Vlan5
Expires
never
never
never
Field Descriptions
igmp: IGMP status and configuration information
group: Information about group members
static: Static group information
Example of Related ProVision Software Command Output.
HP Switch# show ip igmp vlan 1
IGMP Service Protocol Info
Total VLANs with IGMP enabled : 30
Current count of multicast groups joined : 20
VLAN ID : 2
VLAN Name : VLAN2
IGMP version : 2
Querier Address : 10.255.128.2
Querier Port : A1
Querier UpTime : 1h 51m 59s
Querier Expiration Time : 2min 5sec
Ports with multicast routers: A1, A5-A6
Active Group Addresses Type
Expires Ports Reports Queries
---------------------- ----------- ----- -------- ------226.0.6.7
Filter
2min 5sec A1
10
10
226.0.6.8
Standard 3min 20sec A2
20
20
For more information, see the latest Multicast and Routing Guide for your switch.
94
Display Commands
display igmp group x.x.x.x verbose
Comware
Related ProVision
display igmp group x.x.x.x verbose
No equivalent ProVision software command
Displays detailed information about a specified IGMP multicast group.
HP Switch# display igmp group 239.4.4.4 verbose
Interface group report information
Vlan-interface400(192.168.9.2):
Total 5 IGMP Groups reported
Group: 239.4.4.4
Uptime: 00:01:56
Expires: 00:02:06
Last reporter: 192.168.9.9
Last-member-query-counter: 0
Last-member-query-timer-expiry: off
Version1-host-present-timer-expiry: off
Minimum Software Version: 15.10.
display igmp group x.x.x.x verbose
95
display igmp interface
Comware
Related ProVision
display igmp interface
show ip igmp vlan <vid>
Displays IGMP configuration and operation information of the specified interface or all
IGMP-enabled interfaces.
HP Switch# display igmp interface
Interface information
Vlan-interface30(75.1.30.1):
IGMP is enabled
Current IGMP version is 2
Value of query interval for IGMP(in seconds): 125
Value of other querier present interval for IGMP(in seconds): 255
Value of maximum query response time for IGMP(in seconds): 10
Querier for IGMP: 75.1.30.1 (this router)
Total 5 IGMP Groups reported
Field Descriptions
Vlan-interface200 (10.10.1.20): Interface and IP address
Current IGMP version: Version of IGMP currently running on the interface
Value of query interval for IGMP(in seconds): IGMP general query interval, in seconds
Value of other querier present interval for IGMP(in seconds): Other querier present interval, in
seconds
Value of maximum query response time for IGMP(in seconds): Maximum response time for IGMP
general queries, in seconds
Value of last member query interval(in seconds): IGMP last member query interval, in seconds
Value of startup query interval(in seconds): IGMP startup query interval, in seconds
Value of startup query count: Number of IGMP general queries the device sends on startup
General query timer expiry: Remaining time of the IGMP general query timer, where "off" means
that the timer never expires
Querier for IGMP: IP address of the IGMP querier
IGMP activity: Statistics of IGMP activities (joins and leaves)
Multicast routing on this interface: Whether the multicast routing and forwarding function is enabled
Robustness: Robustness variable of the IGMP querier
Require-router-alert: Dropping IGMP messages without Router-Alert (enabled/ disabled)
Fast-leave: Fast leave processing status (enabled/disabled)
Ssm-mapping: IGMP SSM mapping status (enabled/disabled)
Startup-query-timer-expiry: Remaining time of the startup query timer, where "off" means that the
timer never expires
Other-querier-present-timer-expiry: Remaining time of the other querier present timer, where "off"
means that the timer never expires
Proxying interface: IGMP proxy interface, where "none" means that no proxy interface exists
Total 1 IGMP Group reported: Total number of IGMP groups the interface has dynamically joined
IGMP proxy is enabled: IGMP proxying is enabled
Version1-querier-present-timer-expiry: Remaining time of the IGMPv1 querier present timer, where
"off" means that the timer never expires
96
Display Commands
Version2-querier-present-timer-expiry: Remaining time of the IGMPv2 querier present timer, where
"off" means that the timer never expires
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command.
HP Switch# show ip igmp vlan 30
IGMP Service Protocol Info
Total VLANs with IGMP enabled : 2
Current count of multicast groups joined : 5
IGMP Filter Unknown Multicast: Disabled
IGMP Filter Unknown Multicast Status: Disabled
VLAN ID : 30
VLAN Name : VLAN30
IGMP version : 2
Querier Address [this switch] : 75.1.30.1
Querier Port :
Querier UpTime : 5d 18h 39m 7s
Querier Expiration Time : 0h 0m 4s
Active Group Addresses Type Expires Ports Reports Queries
---------------------- ---- ------- ------- ------ ------239.1.1.1
Filter
0h 2m 25s
A2
3961
0
239.1.1.2
Filter
0h 2m 25s
A2
3961
0
239.1.1.3
Filter
0h 2m 25s
A2
3961
0
239.1.1.4
Filter
0h 2m 25s
A2
3961
0
239.1.1.5
Filter
0h 2m 24s
A2
3961
0
Operating Notes
ProVision does not support VPN instance.
For more information, see the latest Multicast and Routing Guide for your switch.
display igmp interface
97
display igmp interface verbose
Comware
Related ProVision
display igmp interface verbose
No equivalent ProVision software command
Displays detailed IGMP configuration and operation information.
HP Switch# display igmp interface verbose
Interface information
Vlan-interface1(10.100.239.141):
IGMP is enabled
Current IGMP version is 2
Value of query interval for IGMP(in seconds): 125
Value of other querier present interval for IGMP(in seconds):
255
Value of maximum query response time for IGMP(in seconds): 10
Value of last member query interval(in seconds): 10
Value of startup query interval(in seconds): 31
Value of startup query count: 2
General query timer expiry (hours:minutes:seconds): 00:01:58
Querier for IGMP: 10.100.239.141 (this router)
IGMP activity: 378 joins, 0 leaves
Multicast routing on this interface: disabled
Robustness: 2
Require-router-alert: enabled
Fast-leave: enabled
Ssm-mapping: n/a
Startup-query-timer-expiry: off
Other-querier-present-timer-expiry: off
Proxying interface: n/a
Total 9 IGMP Groups reported
Vlan-interface2(192.168.9.2):
IGMP is enabled
Current IGMP version is 2
Value of query interval for IGMP(in seconds): 125
Value of other querier present interval for IGMP(in seconds):
255
Value of maximum query response time for IGMP(in seconds): 10
Value of last member query interval(in seconds): 10
Value of startup query interval(in seconds): 31
Value of startup query count: 2
General query timer expiry (hours:minutes:seconds): 00:01:56
Querier for IGMP: 192.168.9.2 (this router)
IGMP activity: 0 joins, 0 leaves
Multicast routing on this interface: disabled
Robustness: 2
Require-router-alert: enabled
Fast-leave: disabled
Ssm-mapping: n/a
Startup-query-timer-expiry: off
Other-querier-present-timer-expiry: off
Proxying interface: n/a
Minimum Software Version: 15.10.
98
Display Commands
display igmp interface vlan-interface <vlan-id>
Comware
Related ProVision
display igmp interface vlan-interface <vlan-id>
show ip igmp vlan <vid>
Displays the IGMP configuration and operation information of the specified interface or all
IGMP-enabled interfaces.
HP Switch# display igmp interface vlan-interface 1
Vlan-interface1(10.100.1.238):
IGMP is enabled
Current IGMP version is 2
Value of query interval for IGMP(in seconds): 125
Value of other querier present interval for IGMP(in seconds): 255
Value of maximum query response time for IGMP(in seconds): 10
Querier for IGMP: 10.100.1.238 (this router)
Total 8 IGMP Groups reported
Field Descriptions
Vlan-interface: Interface and IP address.
Current IGMP Version: Version of IGMP currently running on the interface.
Value of query interval for IGMP(in seconds): IGMP general query interval, in seconds.
Value of other querier present interval for IGMP (in seconds): Other querier present interval, in
seconds.
Value of maximum query response time for IGMP(in seconds): Maximum response time for IGMP
general queries, in seconds.
Querier for IGMP: IP address of the IGMP querier.
Operating Notes
If the VLAN interface is invalid, the switch displays "VLAN <VLAN-ID> not found".
For more information on switch IGMP operation, see the "Multimedia Traffic Control with IP Multicast
(IGMP)" chapter in the latest Advanced Traffic Management Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip igmp vlan 1
IGMP Service Protocol Info
Total VLANs with IGMP enabled : 30
Current count of multicast groups joined : 20
VLAN ID : 2
VLAN Name : VLAN2
IGMP version : 2
Querier Address : 10.255.128.2
Querier Port : A1
Querier UpTime : 1h 51m 59s
Querier Expiration Time : 2min 5sec
Ports with multicast routers: A1, A5-A6
Active Group Addresses
---------------------226.0.6.7
226.0.6.8
Type
---------Filter
Standard
Expires
--------------2min 5sec
3min 20sec
Ports
---------A1
A2
Reports
------10
20
Queries
------10
20
display igmp interface vlan-interface <vlan-id>
99
display igmp interface vlan-interface <vlan-id> Field Mappings.
Comware
ProVision Software
Vlan-interface
VLAN-ID
Current IGMP Version
IGMP version
Value of query interval
n/a
Value of other querier
n/a
Value of maximum query response time
n/a
Querier for IGMP
Querier Address
n/a
VLAN Name
n/a
Querier Port
n/a
Querier UpTime
Startup-query-timer-expiry
Startup-query-timer-expiry
n/a
Ports with multicast routers
n/a
Active Group Addresses
n/a
Type
Startup-query-timer-expiry
Expires
n/a
Ports
n/a
Reports
IGMP activity
Queries
100 Display Commands
display igmp routing-table
Comware
Related ProVision
display igmp routing-table
show ip igmp vlan <vid>
Displays information regarding the IGMP routing table.
HP Switch# display igmp routing-table
Routing table
Total 5 entries
00001. (*, 239.1.1.1)
List of 1 downstream interface
Vlan-interface30 (75.1.30.1),
Protocol: IGMP
00002. (*, 239.1.1.2)
List of 1 downstream interface
Vlan-interface30 (75.1.30.1),
Protocol: IGMP
00003. (*, 239.1.1.3)
List of 1 downstream interface
Vlan-interface30 (75.1.30.1),
Protocol: IGMP
00004. (*, 239.1.1.4)
List of 1 downstream interface
Vlan-interface30 (75.1.30.1),
Protocol: IGMP
00005. (*, 239.1.1.5)
List of 1 downstream interface
Vlan-interface30 (75.1.30.1),
Protocol: IGMP
Field Descriptions
Routing table of VPN-Instance: public net: Public network IGMP routing table
00001: Sequence number of this (*, G) entry
(*, 225.1.1.1): A (*, G) entry of the IGMP routing table
A (*, G) entry of the IGMP routing table IGMP route flags:
•
ACT: Indicates IGMP routing entries that have been used for forwarding data packets but
have the multicast group address out of the SSM group range
•
SUC: Indicates IGMP routing entries that have been added to the forwarding table and have
the multicast group address within the SSM group range
List of 1 downstream interface: Downstream interface list, namely, the interfaces to which multicast
data for this group will be forwarded
in include mode: The downstream interface is in the include mode
in exclude mode: The downstream interface is in the exclude mode
Downstream interface is none: No downstream interfaces exist
Protocol: Protocol type
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ip igmp vlan <vid>" on page
2-51.
display igmp routing-table
101
display interface
Comware
Related ProVision
display interface
show interface <port>
Displays current state about a specified port and related information. If no port number is specified,
information is displayed for all ports.
HP Switch# display interface a1
A1 current state: UP
IP Packet Frame Type: n/a, Hardware Address: 001560-f9b0ff
Description: A1 interface
Loopback is n/a
Media type is twisted Pair
Port hardware type is 100/1000T
1000Mbps-speed mode, full-duplex mode
Link speed type is autonegotiation, link duplex type is
autonegotiation
Flow-control is not enabled
The Maximum Frame Length is 9216
Broadcast MAX-ratio: n/a
Unicast MAX-ratio: n/a
Multicast MAX-ratio: n/a
Jumbo frame: [ see "show jumbos"]
PVID : 1
Mdi type: MDIX
Link delay is n/a
Port link-type: n/a
Tagged VLAN ID : none
Untagged VLAN ID : 1
Port priority: No-override
Last clearing of counters: n/a
Peak value of input: n/a
Peak value of output: n/a
Last 300 seconds input: 0 packets/sec 128846 bytes/sec 0%
Last 300 seconds output: 0 packets/sec 65444 bytes/sec 0%
Input (total): 0 packets, 26 bytes
3 unicasts, 2 broadcasts, 21 multicasts, 0 pauses
Input (normal): 0 packets, 26 bytes
3 unicasts, 2 broadcasts, 21 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, n/a throttles
0 CRC, 0 frame, n/a overruns, n/a aborts
n/a ignored, n/a parity errors
Output (total): 0 packets, 24 bytes
0 unicasts, 4 broadcasts, 20 multicasts, 0 pauses
Output (normal): 0 packets, 24 bytes
0 unicasts, 4 broadcasts, 20 multicasts, 0 pauses
Output: 0 output errors, n/a underruns, n/a buffer failures
n/a aborts, 0 deferred, 0 collisions, 0 late collisions
n/a lost carrier, n/a no carrier
Example of Related ProVision Software Command Output.
HP Switch# show interfaces brief
Status and Counters - Port Status
|
Port Type
|
----- ---------+
B1
100/1000T |
B2
100/1000T |
B3
100/1000T |
102 Display Commands
Intrusion
MDI Flow Bcast
Alert
Enabled Status Mode Mode
--------- ------- ------ ---- ---No
Yes
Down Auto-10-100
No
Yes
Down 1000FDx
No
Yes
Down 1000FDx
Ctrl
---Auto
Auto
Auto
Limit
----off 0
off 0
off 0
B4
B5
B6
100/1000T | No
100/1000T | No
100/1000T | No
Yes
Yes
Yes
Down 1000FDx
Down 1000FDx
Down 1000FDx
Auto off 0
Auto off 0
Auto off 0
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display interface 103
display interface brief
Comware
Related ProVision
display interface brief
show interfaces brief
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays brief information about Layer 3 interfaces (tunnels) and Layer 2 interfaces.
HP Switch(config)# display interface brief
The brief information of interface(s) under route mode:
Link: ADM - administratively down; Stby - standby
Protocol: (s) - spoofing
Interface
Link
Protocol
Main IP
Description
tunnel-1
Down
UP
20.1.1.1
tunnel1
The brief information of interface(s) under bridge
Link: ADM - administratively down; Stby - standby
Speed or Duplex: (a)/A - auto; H - half; F - full
Type: A - access; T - trunk; H - hybrid
Interface
Link Speed
Duplex Type PVID
A1
UP
auto
A
n/a 1
A2
DOWN auto
A
n/a 20
A3
DOWN auto
A
n/a 1
A4
DOWN auto
A
n/a 1
A5
DOWN auto
A
n/a 1
A6
DOWN auto
A
n/a 1
A7
DOWN auto
A
n/a 1
A8
DOWN auto
A
n/a 1
A9
DOWN auto
A
n/a 1
.
.
.
mode:
Description
port1
port2
Field Descriptions
The brief information of interface(s) under route mode: Brief information about Layer 3 interfaces.
The brief information of interface(s) under bridge mode: Brief information about Layer 2 interfaces.
Link: ADM - administratively down; Stby - standby: Link status:
•
ADM—The interface has been administratively shut down. To recover its physical layer state,
perform the undo shutdown command.
•
Stby—The interface is operating as a backup interface.
Speed or Duplex: (a)/A - auto; H - half; F - full: If the speed of an interface is automatically
negotiated, its speed attribute includes the auto negotiation flag, letter a in parentheses. If the
duplex mode of an interface is automatically negotiated, its duplex mode attribute includes the
auto negotiation flag, letter a in parentheses or a capital A. Letter H indicates the half duplex
mode, and letter F indicates the full duplex mode.
Type: A - access; T - trunk; H - hybrid: Link type options for Ethernet interfaces.
Protocol: (s) - spoofing: If the network layer protocol state of an interface is shown as UP, but its
link is an on-demand link or not present, its protocol attribute includes the spoofing flag (an s in
parentheses).
Interface: The abbreviated interface name.
Link: The physical link state of the interface.
Speed: The interface speed, in bps.
104 Display Commands
PVID: The default VLAN ID.
Description: Name of the interface.
Operating Notes
For more information on interface statistics, see the "Port Status and Configuration" chapter in the
latest Management and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show interfaces brief
Status and Counters - Port Status
Port
-----A1
A2
A3
A4
A5
A6
A7
A8
Type
--------10GbE-T
10GbE-T
10GbE-T
10GbE-T
10GbE-T
10GbE-T
10GbE-T
10GbE-T
|
|
+
|
|
|
|
|
|
|
|
Intrusion
Alert
--------No
No
No
No
No
No
No
No
Enabled
------Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Status
-----Up
Down
Down
Down
Down
Down
Down
Down
Mode
---------100 0FDx
10GigFD
10GigFD
10GigFD
10GigFD
10GigFD
10GigFD
10GigFD
MDI Flow Bcast
Mode Ctrl Limit
---- ---- ----MDIX off 0
MDI
off 0
MDIX off 0
Auto off 0
Auto off 0
Auto off 0
Auto off 0
Auto off 0
display interface brief Field Mappings.
Comware
ProVision Software
interfaces under route mode
n/a
interfaces under bridge mode
n/a
Link status
Status
Speed or Duplex
Mode/MDI Mode
Type
n/a
Protocol
n/a
Interface
Port
Link
Status
Speed
Type
PVID
n/a
Description
n/a
n/a
Intrusion Alert
n/a
Bcast Limit
display interface brief 105
display interface brief down
Comware
Related ProVision
display interface brief down
show interfaces brief
Displays information about interfaces in down state and the relevant causes.
HP Switch(config)# display interface brief down
The brief information of interface(s) under route mode:
Link: ADM - administratively down; Stby - standby
Interface Link Cause
tunnel-1 Down n/a
The brief information of interface(s) under bridge mode:
Link: ADM - administratively down; Stby - standby
Interface
Link Cause
A2
Down Not connected
A3
Down Not connected
A4
Down Not connected
A5
Down Not connected
A6
Down Not connected
A7
Down Not connected
.
.
.
Field Descriptions
The brief information of interface(s) under route mode: Brief information about Layer 3 interfaces.
The brief information of interface(s) under bridge mode: Brief information about Layer 2 interfaces.
Link: ADM - administratively down; Stby - standby: Link status:
•
ADM—The interface has been administratively shut down. To recover its physical layer state,
perform the undo shutdown command.
•
Stby—The interface is operating as a backup interface.
Interface: Interface number.
Link Cause: Displays information about interfaces in the down state and the causes.
Operating Notes
For the interfaces under route mode, only "interface tunnels" are displayed; other types are not
supported.
H3C displays one of the reasons for the field "Cause" if the port is down: Not connected,
Administratively, Link-Aggregation interface down, OAM connection failure, DLDP connection
failure, Loopback detection-protected, BPDUprotected, Monitor-Link uplink down.
ProVision doesn&rsquo;t support OAM and DLDP.
For more information, see the "Port Status and Configuration" chapter in the latest Management
and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show interfaces brief
Status and Counters - Port Status
| Intrusion
MDI Flow Bcast
Port
Type
| Alert
Enabled Status Mode
Mode Ctrl Limit
------ --------- + --------- ------- ------ ---------- ---- ---- ----106 Display Commands
A1
A2
A3
A4
A5
A6
A7
A8
10GbE-T
10GbE-T
10GbE-T
10GbE-T
10GbE-T
10GbE-T
10GbE-T
10GbE-T
|
|
|
|
|
|
|
|
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Up
Down
Down
Down
Down
Down
Down
Down
1000FDx
10GigFD
10GigFD
10GigFD
10GigFD
10GigFD
10GigFD
10GigFD
MDIX
MDI
MDIX
Auto
Auto
Auto
Auto
Auto
off
off
off
off
off
off
off
off
0
0
0
0
0
0
0
0
display interface brief down Field Mappings.
Comware
ProVision Software
interfaces under route mode
n/a
interfaces under bridge mode
n/a
Interface
Port
Link Cause
Status
display interface brief down 107
display ip as-path
Comware
Related ProVision
display ip as-path
show ip aspath-list
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays BGP AS-Path list information
HP Switch# display ip as-path
ListID
Mode
Expression
test1
permit
$25
Field Descriptions
ListID: AS path list ID.
Mode: Match mode — permit or deny.
Expression: Regular expression for matching.
Operating Notes
To enable BGP operation in ProVision software, see the “BGP (Border Gateway Protocol)” chapter
in the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch# show ip aspath-list
Route Policy AS-path List test1: 1 entries
seq 5
permit "$25" ip as-path Field Mappings
Comware
ProVision Software
ListID
as-path name
Mode
permit or deny
Expression
$ expression
108 Display Commands
display ip check source
Comware
Related ProVision
display ip check source
show dhcp-snooping bindings
Displays display dynamic IP source guard binding entries.
HP Switch# display ip check source
Total entries found: 3
MAC Address
IP Address
005056-9f2c8b
192.168.1.1
005056-9f2c9b
192.167.1.1
005056-9f2c9b
192.167.0.1
VLAN
1
1
2
Interface
n/a
n/a
n/a
Status
Dynamic
Dynamic
Dynamic
Field Descriptions
Total entries found: Total number of found entries
MAC Address: MAC address of the dynamic IP source guard binding entry. N/A means that no
MAC address is bound in the entry.
IP Address: IP address of the dynamic IP source guard binding entry. N/A means that no IP address
is bound in the entry.
VLAN: VLAN bound to the IP source guard binding entry. N/A means that no VLAN is bound in
the entry.
Interface: Interface of the dynamic IP source guard binding entry.
Type: Type of the dynamic IP source guard binding entry, including:
•
DHCP-SNP—DHCP snooping entry.
•
DHCP-RLY—DHCP relay entry.
•
DHCPv6-SNP—DHCPv6 snooping entry.
•
ND-SNP—ND snooping entry.
Operating Notes
For more information about DHCP snooping, see the "Configuring Advanced Threat Protection"
chapter in the latest Access Security Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show dhcp-snooping
DHCP Snooping Information
DHCP Snooping
: Yes
Enabled Vlans
:
Verify MAC
: Yes
Option 82 untrusted policy : drop
Option 82 Insertion
: Yes
Option 82 remote-id
: mac
Store lease database : Not configured
Port Trust
----- ----B1
No
B2
No
display ip check source 109
display ip check source Field Mappings.
110
Comware
ProVision Software
Total entries found
n/a
MAC Address
n/a
IP Address
n/a
VLAN
n/a
Interface
n/a
Type
n/a
Display Commands
display ip community-list
Comware
Related ProVision
display ip community-list
show ip community-list
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays BGP community list information
HP Switch# display ip community-list
Community List Number community-1
permit 10
deny 50
Field Descriptions
Community List Number < community-name >: Specifies the community being reported.
permit: Permitted routes that belong to the community .
deny: Denied routes that belong to the community.
Operating Notes
To enable BGP in ProVision software, see the “BGP (Border Gateway Protocol)” chapter in the
latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch# show ip community-list
ip community list community-1 standard
permit 10
deny 50
ip as-path Field Mappings.
Comware
ProVision Software
Community List Number
ip community list
permit
permit
deny
deny
display ip community-list
111
display ip http
Comware
Related ProVision
display ip http
No equivalent ProVision software command
Displays information about HTTP.
HP Switch# display ip http
HTTP port: 80
Basic ACL: n/a
Current connection: 0
Operation status: enabled
Minimum Software Version: 15.10.
112
Display Commands
display ip https
Comware
Related ProVision
display ip https
No equivalent ProVision software command
Displays information about HTTPs.
HP Switch# display ip https
HTTPS port: 443
SSL server policy: n/a
Certificate access-control-policy: n/a
Basic ACL: n/a
Operation status: disabled
Minimum Software Version: 15.10.
display ip https
113
display ip ip-prefix
Comware
Related ProVision
display ip ip-prefix
show ip prefix-list
Displays all the prefix list information, including list name, address, length, rule type, ge and le
[greater than or equal /less than or equal w.r.t mask range] for a specific network. This command
is available only in manager mode.
HP Switch# display ip ip-prefix abc
Prefix-list abc
Permitted n/a
Denied n/a
index: 5
permit 11.2.3.4/8 ge 8 le 8
Example of Related ProVision Software Command Output.
HP Switch# show ip prefix-list
ip prefix-list Odd: 4 entries
seq 5 permit 10.1.1.1/24 ge 24 le 24
seq 10 deny 10.1.2.1/24 ge 24 le 24
seq 15 permit 10.1.3.1/24 ge 24 le 24
seq 20 deny 10.1.4.1/24 ge 24 le 24
ip prefix-list Even: 4 entries
seq 5 deny 10.1.1.1/24 ge 24 le 24
seq 10 permit 10.1.2.1/24 ge 24 le 24
seq 15 deny 10.1.3.1/24 ge 24 le 24
seq 20 permit 10.1.4.1/24 ge 24 le 24
Operating Notes
For more information, refer to the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.10.
114
Display Commands
display ipv6 dhcp duid
Comware
Related ProVision
display ipv6 dhcp duid
No equivalent ProVision software command
Displays the DUID of the local switch.
HP Switch# display ipv6 dhcp duid
The DUID of this device: 0003-0001-00e0-fc00-5552.
Field Descriptions
The DUID of this device: The DHCP for IPv6 Unique Identifier (DUID).
Operating Notes
For more information about IPv6 DHCPv6, see the "DHCPv6-Relay" chapter in the latest IPv6
Configuration Guide for your switch.
display ipv6 dhcp duid
115
display ipv6 dhcp relay server-address all
Comware
Related ProVision
display ipv6 dhcp relay server-address all
show ipv6 helper-address
Displays all DHCPv6 server address information.
HP Switch# display ipv6 dhcp relay server-address all
Interface: Vlan2
Server address(es) Output Interface
1::1
FF02::1:2
Vlan4
Interface: Vlan3
Server address(es)
1::1
FF02::1:2
Vlan4
Output Interface
Field Descriptions
Interface: Interface that serves as the DHCPv6 relay agent.
Server address(es): DHCPv6 server address(es) specified on the interface.
Output Interface: Outgoing interface of DHCPv6 packets.
Operating Notes
For more information about IPv6 DHCPv6, see the "DHCPv6-Relay" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 helper-address
VLAN: 14
IPv6 Helper Address
Egress Vlan
---------------------------------------------- ----------FF05::1:3
14
display ipv6 dhcp relay server-address all Field Mappings.
116
Comware
ProVision Software
Interface
VLAN
Server address(es)
IPv6 Helper Address
Output Interface
Egress Vlan
Display Commands
display ipv6 dhcp relay server-address interface <id>
Comware
Related ProVision
display ipv6 dhcp relay server-address interface <id>
show ipv6 helper-address
Displays DHCPv6 server address information of the specified interface.
HP Switch# display ipv6 dhcp relay server-address interface vlan-interface 2
Interface: Vlan2
Server address(es)
Output Interface
1::1
FF02::1:2
Vlan4
Field Descriptions
Interface: Interface that serves as the DHCPv6 relay agent.
Server address(es): DHCPv6 server address(es) specified on the interface.
Output Interface: Outgoing interface of DHCPv6 packets.
Operating Notes
For more information about IPv6 DHCPv6, see the "DHCPv6-Relay" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 helper-address
VLAN: 14
IPv6 Helper Address
Egress Vlan
---------------------------------------------- ----------FF05::1:3
14
display ipv6 dhcp relay server-address interface <id> Field Mappings.
Comware
ProVision Software
Interface
VLAN
Server address(es)
IPv6 Helper Address
Output Interface
Egress Vlan
display ipv6 dhcp relay server-address interface <id>
117
display ipv6 dhcp relay statistics
Comware
Related ProVision
display ipv6 dhcp relay statistics
show dhcpv6-relay
Displays packet statistics on the DHCPv6 relay agent. Field
HP Switch# display ipv6 dhcp relay statistics
Packets dropped
: 4
Error
: 4
Excess of rate limit : n/a
Packets received
: 14
SOLICIT
: 0
REQUEST
: 0
CONFIRM
: 0
RENEW
: 0
REBIND
: 0
RELEASE
: 0
DECLINE
: 0
INFORMATION-REQUEST : 7
RELAY-FORWARD
: 0
RELAY-REPLY
: 7
Packets sent
: 14
ADVERTISE
: 0
RECONFIGURE
: 0
REPLY
: 7
RELAY-FORWARD
: 7
RELAY-REPLY
: 0
Field Descriptions
Packets dropped: Number of discarded packets.
Error: Number of discarded error packets.
Excess of rate limit: Number of packets discarded due to excess of rate limit.
Packets received: Number of received packets.
SOLICIT: Number of received solicit packets.
REQUEST: Number of received request packets.
CONFIRM: Number of received confirm packets.
RENEW: Number of received renew packets.
REBIND: Number of received rebind packets.
RELEASE: Number of received release packets.
DECLINE: Number of received decline packets.
INFORMATION-REQUEST: Number of received information request packets.
RELAY-FORWARD: Number of received relay-forward packets.
RELAY-REPLY: Number of received relay-reply packets.
Packets sent: Number of sent packets.
ADVERTISE: Number of sent advertise packets.
RECONFIGURE: Number of sent reconfigure packets.
REPLY: Number of sent reply packets.
RELAY-FORWARD: Number of sent Relay-forward packets.
RELAY-REPLY: Number of sent Relay-reply packets.
118
Display Commands
Operating Notes
For more information about IPv6 DHCPv6, see the "DHCPv6-Relay" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show dhcpv6-relay
DHCPV6 Relay Agent : Enabled
Client Requests
VLAN Name
---------DEFAULT...
VLAN20
Received
---------120
30
Dropped
---------0
1
Server Responses
Failed
---------0
0
Received
---------120
29
Dropped
---------0
2
Failed
---------0
1
display ipv6 dhcp relay statistics Field Mappings.
Comware
ProVision Software
Packets dropped
Dropped
Error
Failed
Excess of rate limit
n/a
Packets received
Received
display ipv6 dhcp relay statistics
119
display ipv6 fib
Comware
Related ProVision
display ipv6 fip
show ipv6 route
Displays IPv6 FIB entries. If no argument is specified, all IPv6 FIB entries will be displayed. The
switch looks up a matching IPv6 FIB entry for forwarding an IPv6 packet.
HP Switch(config)# display ipv6 fib
FIB Table:
Total number of Routes : n/a
Flag:
U:Useable
G:Gateway
Destination:
NextHop
:
Label
:
H:Host
B:Blackhole
D:Dynamic
::1
::1
n/a
S:Static
PrefixLength : 128
Flag
: UH
Token
: n/a
Field Descriptions
Total number of Routes: Total number of routes in the FIB.
Destination: Destination address.
PrefixLength: Prefix length of the destination address.
NextHop: Next hop.
Flag: Route flag:
•
U — Usable route
•
G — Gateway route
•
H — Host route
•
B — Black hole route
•
D — Dynamic route
•
S — Static route
Label: Label.
Token: LSP index number.
Interface: Outgoing interface.
Operating Notes
For more information, see the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide
for your switch.
Minimum Software Version: 15.11.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 route
IPv6 Route Entries
Dest : ::/0
Gateway : fe80::213:c4ff:fedd:14b0%vlan10
Dist. : 40
Dest : ::1/128
Gateway : lo0
Dist. : 0
120 Display Commands
Type : static
Metric : 0
Type : connected
Metric : 1
Dest : 2001:db8:a03:e102::/64
Gateway : VLAN10
Dist. : 0
Type : connected
Metric : 1
Dest : fe80::%vlan10
Gateway : VLAN10
Dist. : 0
Type : connected
Metric : 1
Dest : fe80::1%lo0
Gateway : lo0
Dist. : 0
Type : connected
Metric : 1
display ipv6 fib
121
display ipv6 fib <ip-address>
Comware
Related ProVision
display ipv6 fib <ip-address>
show ipv6 route
Displays the IPv6 FIB entry of the specified destination IPv6 address. Note the following:
•
Without the prefix-length argument specified, this command displays the matching IPv6 FIB
entry with the longest prefix.
•
With the prefix-length argument specified, this command displays the IPv6 FIB entry exactly
matching the specified destination IPv6 address and prefix length.
HP Switch(config)# display ipv6 fib ::1
FIB Table:
Total number of Routes : n/a
Flag:
U:Useable
G:Gateway
Destination:
NextHop
:
Label
:
Interface :
H:Host
B:Blackhole
::1
::1
n/a
InLoopBack0
D:Dynamic
S:Static
PrefixLength : 128
Flag
: UH
Token
: n/a
Field Descriptions
Total number of Routes: Total number of routes in the FIB.
Destination: Destination address.
PrefixLength: Prefix length of the destination address.
NextHop: Next hop.
Flag: Route flag:
•
U — Usable route
•
G — Gateway route
•
H — Host route
•
B — Black hole route
•
D — Dynamic route
•
S — Static route
Label: Label.
Token: LSP index number.
Interface: Outgoing interface.
Operating Notes
For more information, see the “OSPFv3 Routing” chapter in the latest IPv6 Configuration Guide
for your switch.
Minimum Software Version: 15.11.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 route
IPv6 Route Entries
122
Display Commands
Dest : ::/0
Gateway : fe80::213:c4ff:fedd:14b0%vlan10
Dist. : 40
Type : static
Metric : 0
Dest : ::1/128
Gateway : lo0
Dist. : 0
Dest : 2001:db8:a03:e102::/64
Gateway : VLAN10
Dist. : 0
Dest : fe80::%vlan10
Gateway : VLAN10
Dist. : 0
Dest : fe80::1%lo0
Gateway : lo0
Dist. : 0
Type : connected
Metric : 1
Type : connected
Metric : 1
Type : connected
Metric : 1
Type : connected
Metric : 1
display ipv6 fib <ip-address>
123
display ipv6 neighbors all
Comware
Related ProVision
display ipv6 ipv6 neighbors all
show ipv6 neighbors
Displays neighbor information.
HP Switch(config)# display ipv6 neighbors all
Type: S-Static
IPv6 Address
FE80::200:5EFF:FE32:B800
D-Dynamic
Link-layer
0000-5e32-b800
VID
N/A
Interface State
GE3/0/1
REACH
T
Age
S
-
Field Descriptions
IPv6 Address: IPv6 address of a neighbor.
Link-layer: Link layer address (MAC address of a neighbor).
VID: VLAN to which the interface connected with a neighbor belongs.
Interface: Interface connected with a neighbor.
State: State of neighbor, including:
•
NCMP: The address is being resolved. The link layer address of the neighbor is unknown.
•
REACH: The neighbor is reachable.
•
STALE: The reachability of the neighbor is unknown. The switch will not verify the reachability
any longer unless data is sent to the neighbor.
•
DELAY: The reachability of the neighbor is unknown. The switch sends an NS message after
a delay.
•
PROBE: The reachability of the neighbor is unknown. The switch sends an NS message to
verify the reachability of the neighbor.
T: Type of neighbor information, including static configuration and dynamic acquisition.
Age: For a static entry, a hyphen “-“ is displayed. For a dynamic entry, the reachable time (in
seconds) elapsed is displayed, and if it is never reachable, “#” is displayed (for a neighbor acquired
dynamically).
VPN-instance Name: Name of a VPN. [No Vrf] indicates no VPN is configured.
Operating Notes
For more information, see the “IPv6 Management Features” chapter in the latest IPv6 Configuration
Guide for your switch.
Minimum Software Version: 15.11.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 neighbors
IPv6 ND Cache Entries
IPv6 Address
--------------------------------------2001:db8:260:212::101
2001:db8:260:214::1:15
fe80::1:1
124
Display Commands
MAC Address
------------0013c4-dd14b0
001279-88a100
001279-88a100
State
----STALE
REACH
REACH
Type
Port
------- ---dynamic A1
local
local
fe80::10:27
fe80::213:c4ff:fedd:14b0
001560-7aadc0 REACH dynamic A3
0013c4-dd14b0 REACH dynamic A1
display ipv6 neighbors all
125
display ipv6 routing-table
Comware
Related ProVision
display ipv6 routing-table
show ipv6 route
Displays brief ipv6 routing information. The verbose option displays detailed information about
the ipv6 routing table.
HP Switch# display ipv6 routing-table
Routing Table: Public
Destinations: 3
Routes : 3
Destination: ::1/128
NextHop : ::1
Interface : InLoop0
Protocol : Direct
Preference: 0
Cost
: 0
Destination: 6::/64
NextHop : FE80::3A22:D6FF:FEB4:4450
Interface : Vlan2
Protocol : OSPFv3
Preference: 10
Cost
: 2
Destination: 7::/64
NextHop : 7::2
Interface : Vlan2
Protocol : Direct
Preference: 0
Cost
: 0
HP Switch# display ipv6 routing-table verbose
Routing Table : Public
Destinations : 2
Routes : 2
Destination : ::1
NextHop
: ::1
RelayNextHop : n/a
Neighbor
: n/a
Interface
: InLoopBack0
State
: Active NoAdv
Tunnel ID
: n/a
Age
: 28864sec
Destination : 6::
NextHop
: FE80::3A22:D6FF:FEB4:4450
RelayNextHop : n/a
Neighbor
: n/a
Interface
: Vlan-interface2
State
: Active Adv
Tunnel ID
: n/a
Age
: 21665sec
PrefixLength : 128
Preference
: 0
Tag
: n/a
ProcessID
: n/a
Protocol
: Direct
Cost
: 0
Label
: n/a
PrefixLength : 64
Preference : 10
Tag : n/a
ProcessID : n/a
Protocol : OSPFv3
Cost : 2
Label : n/a
Example of Related ProVision Software Command Output.
HP Switch# show ipv6 route
IPv6 Route Entries
Destination : ::/0
Gateway : 2001:db8:e::55:2
Type : static Sub-Type : NA Distance : 130 1 Metric : 1
Destination : ::1/128
Gateway : lo0
Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:1::127/128
Gateway : lo6
126
Display Commands
Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:a::/64
Gateway : fe80::22:1%vlan22
Type : ospf3 Sub-Type : InterArea Distance : 110 Metric : 2
Destination : 2001:db8:b::/64
Gateway : VLAN22
Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:c::/64
Gateway : 2001:db8:e::55:2
Type : static Sub-Type : NA Distance : 120 Metric : 1
-- MORE --, next page: Space, next line: Enter, quit: Control-C
Operating Notes
For more information, refer to the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.10.
display ipv6 routing-table
127
display ipv6 routing-table ipv6-address
Comware
Related ProVision
display ipv6 routing-table ipv6-address
show ipv6 route
Displays routing information for a specified destination ipv6 address. The verbose option displays
detailed information for the specified destination ipv6 address.
HP Switch# display ipv6 routing-table 6::1 64
Routing Table : n/a
Summary Count : n/a
Destination : 6::/64
Protocol
: Direct
NextHop
: 6::1
Preference : 0
Interface
: Vlan2
Cost
: 1
HP Switch# display ipv6 routing-table 6::1 64 verbose
Routing Table : n/a
Summary Count : n/a
Destination : 6::
PrefixLength : 64
NextHop
: 6::1
Preference
: 0
RelayNextHop : n/a
Tag
: n/a
Neighbor
: n/a
Process ID : n/a
Interface : Vlan-interface2
Protocol
: Direct
State
: n/a
Cost
: 1
Tunnel ID
: n/a
Label
: n/a
Age
: n/a
Example of Related ProVision Software Command Output.
HP Switch# show ipv6 route
IPv6 Route Entries
Destination : ::/0
Gateway : 2001:db8:e::55:2
Type : static Sub-Type : NA Distance : 130 1 Metric : 1
Destination : ::1/128
Gateway : lo0
Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:1::127/128
Gateway : lo6
Type : connected Sub-Type : NA Distance : 0 Metric : 1
Destination : 2001:db8:a::/64
Gateway : fe80::22:1%vlan22
Type : ospf3 Sub-Type : InterArea 2 Distance : 110 Metric : 2
Destination : 2001:db8:b::/64
Gateway : VLAN22
Type : connected Sub-Type : NA Distance : 0 3 Metric : 1
Destination : 2001:db8:c::/64
Gateway : 2001:db8:e::55:2
Type : static Sub-Type : NA Distance : 120 Metric : 1
-- MORE --, next page: Space, next line: Enter, quit: Control-C
Operating Notes
For more information, refer to the latest IPv6 Configuration Guide for your switch.
128
Display Commands
Minimum Software Version: 15.10.
display ipv6 routing-table ipv6-address
129
display ipv6 routing-table protocol
Comware
Related ProVision
display ipv6 routing-table protocol
show ipv6 route {connected | static | ospf3}
NOTE:
This command is not supported for OSPFv3 on the HP 2920 Series switches.
Displays routing information for a specified routing protocol. The routing protocol specified may
be static, direct or ospfv3.
HP Switch# display ipv6 routing-table protocol direct
Routing Table: n/a
Destinations: 1
Routes: 1
Destination : ::1/128
NextHop
: ::1
Interface
: InLoop0
Protocol
: Direct
Preference : 0
Cost
: 1
HP Switch# display ipv6 routing-table protocol direct verbose
Routing Table: n/a
Destinations: 1
Routes: 1
Destination : ::1
NextHop
: ::1
RelayNextHop : n/a
Neighbor
: n/a
Interface
: InLoopBack0
State
: Active Adv
Tunnel ID
: n/a
Age
: 37221sec
PrefixLength : 128
Preference
: 0
Tag
: n/a
Process ID : n/a
Protocol
: Direct
Cost
: 1
Label
: n/a
Example of Related ProVision Software Command Output.
HP Switch# show ipv6 route static
IPv6 Route Entries
Destination : 2620:a::/64
Gateway : 2620:b::22:1
Type : static Sub-Type : NA Distance : 1 Metric : 1
Destination : 2620:c::/64
Gateway : 2620:e::55:2
Type : static Sub-Type : NA Distance : 1 Metric : 1
Operating Notes
For more information, refer to the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.10.
130 Display Commands
display lacp system-id
Comware
Related ProVision
display lacp system-id
show lacp local
Displays the system ID of the local system. The system LACP priority and the system MAC address
comprise the system ID.
HP Switch# display lacp system-id
Actor System ID: 0x2f00, 001871-c42f00
Field Descriptions
Actor System ID: The local system ID, including system LACP priority and system
MAC address. In the above example:
•
0x2f00 =
System LACP Priority
•
001871-c42f00 =
System MAC Address
Operating Notes
To enable LACP operation in ProVision software, use the following command from the context of
a port interface on which you want to enable LACP:
lacp
For more on LACP operation in ProVision software, refer to the “Port Trunking” chapter in the latest
Management and Configuration Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output. The ProVision software includes a list
of ports configured for LACP operation, along with some additional data fields.
HP Switch(eth-A13-A14)# show lacp local
LACP Local Information.
System ID: 001871-c42f00
Port
---A13
A14
Trunk
-----A13
A14
LACP
Mode
-------Active
Active
Aggregated
----------Yes
Yes
Tx
Timer
-----Fast
Fast
Rx Timer
Expired
-------No
No
lacp system-id Field Mappings.
Comware
ProVision Software
Actor System ID
System ID
n/a
Port
n/a
Trunk
n/a
LACP Mode
n/a
Aggregated
display lacp system-id
131
132
Comware
ProVision Software
n/a
Tx Timer
n/a
Rx Timer Expired
Display Commands
display link-aggregation
Comware
Related ProVision
display link-aggregation load-sharing mode
n/a
Displays the load-sharing criteria for load-sharing link-aggregation (trunk) groups.
NOTE: Link-aggregation in ProVision software is termed port trunking. Load-sharing is termed
load-balancing.
When load-balancing is configured as L4-based, the load-sharing mode includes source and
destination MAC address, source and destination IP address, and source and destination TCP/UDP
port number, as shown below.
HP Switch(config)# display link-aggregation load-sharing mode
Layer 4 traffic: destination-mac address, source-mac address,
destination-ip address, source-ip address,
destination-port,
source-port
When load-balancing is configured as L3-based, the load-sharing mode includes source and
destination MAC address, and source and destination IP address, as shown below.
HP Switch(config)# display link-aggregation load-sharing mode
Layer 3 traffic: destination-mac address, source-mac address
destination-ip address, source-ip address
Operating Notes
To enable trunk load-balancing in ProVision software, use the following command in the global
configuration context:
trunk < port-list > trkn trunk
trunk-load-balance < L3-based | L4-based >
For more on trunk load-balancing, refer to the “Port Trunking” chapter in the latest Management
and Configuration Guide for your switch.
Minimum Software Version: 15.08.
display link-aggregation
133
display link-aggregation member-port
Comware
Related ProVision
display link-aggregation member-port display
link-aggregation member-port GigabitEthernet
<port-number>
No equivalent ProVision software command
Displays the detailed link aggregation information of the specified member ports or all member
ports if no port is specified.
For a member port in a static aggregation group, only the port number and operational key are
displayed, because the aggregation group is unaware of information about the peer groups.
HP Switch# display link-aggregation member-port
Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,
D -- Synchronization, E -- Collecting, F -- Distributing,
G -- Defaulted, H -- Expired
1:
Aggregation Interface: Trk1
Port Number: 1
Oper-Key: 1
2:
Aggregation Interface: Dyn1
Local:
Port Number: 2
Port Priority: 32768
Oper-Key: 2
Flag: n/a
Remote:
System ID: 0x8000, 0000-0000-0000
Port Number: 0
Port Priority: 32768
Oper-Key: 0
Flag: n/a
Received LACP Packets: 0 packet(s)
Illegal: 0 packet(s)
Sent LACP Packets: 0 packet(s)
Field Descriptions
Flags: One-octet LACP state flags field:
134
•
A indicates whether LACP is enabled. 1 for enabled and 0 for disabled.
•
B indicates the timeout control value. 1 for short timeout, and 0 for long timeout.
•
C indicates whether the link is considered as aggregatable by the sending system. 1 for true,
and 0 for false.
•
D indicates whether the link is considered as synchronized by the sending system. 1 for true,
and 0 for false.
•
E indicates whether the sending system considers that collection of incoming frames is enabled
on the link. 1 for true and 0 for false.
•
F indicates whether the sending system considers that distribution of outgoing frames is enabled
on the link. 1 for true and 0 for false.
Display Commands
•
G indicates whether the receive state machine of the sending system is using default operational
partner information. 1 for true and 0 for false.
•
H indicates whether the receive state machine of the sending system is in the expired state. 1
for true and 0 for false.
If a flag bit is set to 1, the corresponding English letter that otherwise is not output is displayed.
Aggregation Interface: Aggregate interface to which the port belongs.
Port Priority: Aggregation priority of the port.
Oper-key:
Operational key.
display link-aggregation member-port
135
display link-aggregation summary
Comware
Related ProVision
display link-aggregation summary
No equivalent ProVision software command
Displays the summary information of all aggregation groups.
Information about the remote system for a static link aggregation group may be either shown as
none or not displayed, because the aggregation group is unaware of information about the peer
groups.
HP Switch# display link-aggregation summary
Aggregation Interface Type:
BAGG -- Bridge-Aggregation, RAGG -- Route-Aggregation
Aggregation Mode: S -- Static, D -- Dynamic
Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing
Actor System ID: 0x43c0, 0017a4-ff43c0
AGG
AGG
Partner ID
Select Unselect
Share
Interface
Mode
Ports Ports
Type
------------------------------------------------------------------------Dyn1
D
0x0, 0017a4-7eef40
n/a
n/a
n/a
Field Descriptions
Aggregation Interface Type: Aggregate interface type:
•
BAGG for a Layer 2 aggregate interface.
•
RAGG for a Layer 3 aggregate interface.
Aggregation Mode: Aggregation group type:
•
S for static link aggregation.
•
D for dynamic aggregation.
Loadsharing Type: Loadsharing type:
•
Shar for load sharing.
•
NonS for non-load sharing.
Actor System ID: Local system ID, which comprises the system LACP priority and the system MAC
address.
AGG Interface: Type and number of the aggregate interface.
Partner ID: System ID of the partner, which comprises the system LACP priority and the system
MAC address. AGG Mode: Aggregation group type.
Select Ports: The number of Selected ports.
Unselect Ports: The number of Unselected ports.
Share Type: Load sharing type.
136
Display Commands
display link-aggregation verbose
Comware
Related ProVision
display link-aggregation verbose display link-aggregation No equivalent ProVision software command
verbose Bridge-aggregation display link-aggregation
verbose Bridge-aggregation <aggregation-id>
Displays detailed information about the aggregation groups corresponding to the aggregate
interfaces in the system.
To display the information of a specific Layer 2 aggregation group, use the display link-aggregation
verbose bridge-aggregation bridge-aggregation-number command.
To display the information of all Layer 2 aggregate interfaces, use the display link-aggregation
verbose bridge-aggregation command.
HP Switch# display link-aggregation verbose bridge-aggregation
Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing
Port Status: S -- Selected, U -- Unselected
Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,
D -- Synchronization, E -- Collecting, F -- Distributing,
G -- Defaulted, H -- Expired
Aggregation Interface: Trk1
Aggregation Mode: Static
Loadsharing Type: Shar
Port
Status
Oper-Key
--------------------------------------------------------------------------A1
n/a
1
Aggregation Interface: Dyn1
Aggregation Mode: Dynamic
Loadsharing Type: Shar
System ID: none
Local:
Port
Status Priority Oper-Key Flag
---------------------------------------------------------------------------A2
n/a
32768
2
n/a
Remote:
Actor
Partner Priority Oper-Key SystemID
Flag
---------------------------------------------------------------------------A2
0
32768
0
n/a
n/a
Field Descriptions
Loadsharing Type: Loadsharing type:
•
Shar for load sharing.
•
NonS for non-load sharing.
Port Status: Port state: Selected or unselected.
Flags: One-octet LACP state flags field:
•
A indicates whether LACP is enabled. 1 for enabled and 0 for disabled.
•
B indicates the timeout control value. 1 for short timeout, and 0 for long timeout.
•
C indicates whether the link is considered as aggregatable by the sending system. 1 for true,
and 0 for false.
•
D indicates whether the link is considered as synchronized by the sending system. 1 for true,
and 0 for false.
display link-aggregation verbose
137
•
E indicates whether the sending system considers that collection of incoming frames is enabled
on the link. 1 for true and 0 for false.
•
F indicates whether the sending system considers that distribution of outgoing frames is enabled
on the link. 1 for true and 0 for false.
•
G indicates whether the receive state machine of the sending system is using default operational
partner information. 1 for true and 0 for false.
•
H indicates whether the receive state machine of the sending system is in the expired state. 1
for true and 0 for false.
If a flag bit is set to 1, the corresponding English letter that otherwise is not output is displayed.
Aggregation Interface: Name of the aggregate interface.
Aggregation Mode: Type of the aggregation group:
•
Static for static aggregation.
•
Dynamic for dynamic aggregation.
Port: Port type and number.
Status: State of the port.
Oper-Key: Operational key value.
138
Display Commands
display lldp local-information
Comware
Related ProVision
display lldp local-information
No equivalent ProVision software command
Displays the LLDP information. This includes the global information and per interface information.
HP Switch# display lldp local-information
Global LLDP local-information
Chassis ID
: 0000-0000-1122
System name
: HP-E3500yl-48G
System description : HP J8693A Switch E3500yl-48G, revision
K.15.09.0000x, ROM
K.15.28
HP-3500yl-48G
Copyright (C) 1991-2012 Hewlett-Packard Development Company,
L.P.
System capabilities supported : Bridge, Router
System capabilities enabled : Bridge
MED information
device class : network Connectivity //This is intentional
(MED inventory information of master board)
HardwareRev
: Rev 0
FirmwareRev
: K.15.28
SoftwareRev
: K.15.09.0000x
SerialNum
: SG729TH003
Manufacturer name
: Hewlett-Packard
Model name
: J8693A
Asset tracking identifier : Unknown
LLDP local-information of port 1 :
Port ID subtype : local
Port ID
: 1
Port description : 1
Management
Management
Management
Management
Management
Port
Port
port
Port
address
address
address
address
address
type
:
:
interface type :
interface ID
:
OID
:
ipv4
1.2.3.4
ipv6
578
0
VLAN ID(PVID) : 1
and protocol VLAN ID(PPVID) : n/a
and protocol VLAN supported : n/a
and protocol VLAN enabled
: n/a
VLAN name of VLAN 1
: n/a
Auto-negotiation supported : Yes
Auto-negotiation enabled
: Yes
OperMau
: 30
PoE supported
: n/a
Link aggregation supported : n/a
Link aggregation enabled
: n/a
Aggregation port ID
: n/a
Maximum frame Size
: n/a
Media policy type : voice Signaling
display lldp local-information
139
Unknown Policy
VLAN tagged
Media policy VlanID
Media policy L2 priority
Media policy Dscp
:
:
:
:
:
No
No
1
6
46
LLDP local-information of port 2 :
Port ID subtype : local
Port ID
: 2
Port description : 2
Management
Management
Management
Management
Management
address
address
address
address
address
type
:
:
interface type :
interface ID
:
OID
:
Port VLAN ID(PVID)
: 1
ipv4
10.0.0.5
ipv6
578
zeroDotZero
Port and protocol VLAN ID(PPVID) : n/a
port and protocol VLAN supported : n/a
Port and protocol VLAN enabled
: n/a
VLAN name of VLAN <number>
Auto-negotiation supported
Auto-negotiation enabled
OperMau
PoE supported
: n/a
: Yes
: Yes
: 30
: n/a
Link aggregation supported : n/a
Link aggregation enabled
: n/a
Aggregation port ID
: n/a
Maximum frame Size
: n/a
Media policy type : voice Signaling
Unknown Policy
: No
VLAN tagged
: No
Media policy VlanID
: 1
Media policy L2 priority : 6
Media policy Dscp
: 46
140 Display Commands
display lldp local-information global
Comware
Related ProVision
display lldp local-information global
No equivalent ProVision software command
Displays LLDP system global information.
HP Switch# display lldp local-information global
Global LLDP local-information
Chassis ID
: 0000-0000-1122/00
System name
: HP-E3500yl-48G
System description : HP J8693A Switch E3500yl-48G, revision
K.15.09.0000x, ROM
K.15.28
HP-3500yl-48G
Copyright (C) 1991-2012 Hewlett-Packard Development Company,
L.P.
System capabilities supported : Bridge, Router
System capabilities enabled
: Bridge
MED information
device class : network Connectivity
(MED inventory information of master board)
HardwareRev
: Rev 0
FirmwareRev
: K.15.28
SoftwareRev
: K.15.09.0000x
SerialNum
: SG729TH003
Manufacturer name
: Hewlett-Packard
Model name
: J8693A
Asset tracking identifier : Unknown
display lldp local-information global
141
display lldp local-information interface interface-type interface-number
Comware
Related ProVision
display lldp local-information interface interface-type
interface-number
No equivalent ProVision software command
Displays LLDP detailed information for a given interface.
HP Switch# display lldp local-information interface 47
LLDP local-information of port 47 :
Port ID subtype : local
Port ID
: 47
Port description : 47
Management
Management
Management
Management
Management
address
address
address
address
address
type
:
:
interface type :
interface ID
:
OID
:
ipv4
1.2.3.4
ipv6
578
0
Port VLAN ID(PVID) : 1
Port and protocol VLAN ID(PPVID) : n/a
Port and protocol VLAN supported : n/a
Port and protocol VLAN enabled
: n/a
VLAN name of VLAN 1: n/a
Auto-negotiation supported : Yes
Auto-negotiation enabled
: Yes
OperMau
:30
Power port class
PSE power supported
PSE power enabled
PSE pairs control ability
Power pairs
Port power classification
:
:
:
:
:
:
n/a
n/a
n/a
n/a
n/a
n/a
Link aggregation supported
Link aggregation enabled
Aggregation port ID
Maximum frame Size
:
:
:
:
MED information
Media policy type
Unknown Policy
VLAN tagged
Media policy VlanID
Media policy L2 priority
Media policy Dscp
voice Signaling
No
No
1
6
46
:
:
:
:
:
:
n/a
n/a
n/a
n/a
PoE PSE power source
: n/a
Port PSE Priority
: n/a
Port available power value : n/a
142
Display Commands
display lldp neighbor-information brief
Comware
Related ProVision
display lldp neighbor-information brief
show lldp info remote-device
Displays brief information of all the ports connected to neighbors.
HP Switch# display lldp neighbor-information brief
LLDP neighbor-information of port 1 :
Neighbor 1:
ChassisID/subtype: 0023-4751-ba80/MAC address
PortID/subtype
: 34/Locally assigned
Capabilities
: Bridge,Router
LLDP neighbor-information of port 2 :
Neighbor 1:
ChassisID/subtype: 0021-f71b-fc40/MAC address
PortID/subtype
: 1/Locally assigned
Capabilities
: Bridge,Router
Example of Related ProVision Software Command Output.
HP Switch# show lldp info remote-device A3
LLDP Remote Device Information Detail
Local Port : A3
ChassisType : mac-address
ChassisId : 00 16 35 ff 2d 40
PortType : local
PortId : 23
SysName : HPSwitch
System Descr : HP Switch 3500-24, revision K.14.xx
PortDescr : 23
Pvid : 55
System Capabilities Supported : bridge, router
System Capabilities Enabled : bridge
Remote Management Address
Type : ipv4
Address : 10.0.102.198
Poe Plus Information Detail
Poe Device Type : Type2 PD
Power Source : Only PSE
Power Priority : low
PD Requested Power Value : 20 Watts
PSE Actual Power Value : 20 Watts
For more information, see the latest Management and Configuration Guide for your switch.
display lldp neighbor-information brief
143
display lldp neighbor-information list display lldp neighbor-information list
system-name <string>
Comware
Related ProVision
display lldp neighbor-information list display lldp
neighbor-information list system-name <string>
show lldp info remote-device
HP Switch# display lldp neighbor_information list
System Name Local Interface
Chassis ID
HP Switch
1
00 0f 90 dc 9f 80
Port ID
1
Example of Related ProVision Software Command Output.
HP Switch# show lldp info remote-device A3
LLDP Remote Device Information Detail
Local Port : A3
ChassisType : mac-address
ChassisId : 00 16 35 ff 2d 40
PortType : local
PortId : 23
SysName : HPSwitch
System Descr : HP Switch 3500-24, revision K.14.xx
PortDescr : 23
Pvid : 55
System Capabilities Supported : bridge, router
System Capabilities Enabled : bridge
Remote Management Address
Type : ipv4
Address : 10.0.102.198
Poe Plus Information Detail
Poe Device Type : Type2 PD
Power Source : Only PSE
Power Priority : low
PD Requested Power Value : 20 Watts
PSE Actual Power Value : 20 Watts
Whereas Comware can accpet multiple strings as input with spaces for system name, ProVision
accepts only one string.
For more information, see the latest Management and Configuration Guide for your switch.
144 Display Commands
display lldp statistics
Comware
Related ProVision
display lldp statistics
show lldp stats
Displays information about LLDP packets that are being advertised by the local system or by remote
systems, and global LLDP information followed by each interface in the switch. The statistics refer
to significant events that involve LLDP packet transmission and reception.
HP Switch# display lldp statistics
LLDP statistics global information:
LLDP neighbor information last change time:33 days,19 hours,39
minutes,37 seconds
The number of LLDP neighbor information inserted : 10
The number of LLDP neighbor information deleted
: 10
The number of LLDP neighbor information dropped
: 0
The number of LLDP neighbor information aged out : 8
LLDP statistics information of port 1 [GigabitEthernet1/0/1]:
The number of LLDP frames transmitted
: 1713
The number of LLDP frames received
: 1200
The number of LLDP frames discarded
: 0
The number of LLDP error frames
: 1200
The number of LLDP TLVs discarded
: 1200
The number of LLDP TLVs unrecognized
: 0
The number of LLDP neighbor information aged out : 1
The number of CDP frames transmitted
: n/a
The number of CDP frames received
: n/a
The number of CDP frames discarded
: n/a
The number of CDP error frames
: n/a
LLDP statistics information of port 2 [GigabitEthernet1/0/2]:
The number of LLDP frames transmitted
: 2783
The number of LLDP frames received
: 1211
The number of LLDP frames discarded
: 0
Example of Related ProVision Software Command Output.
HP Switch# show lldp stats
LLDP Device Statistics
Neighbor Entries List Last Updated : 2 hours
New Neighbor Entries Count : 20
Neighbor Entries Deleted Count : 20
Neighbor Entries Dropped Count : 0
Neighbor Entries AgeOut Count : 20
LLDP Port Statistics
Port
| NumFramesRecvd NumFramesSent NumFramesDiscarded
------ + -------------- ------------- -----------------A1
|
97317
97843
0
A2
|
21
12
0
A3
|
0
0
0
A4
|
446
252
0
A5
|
0
0
0
A6
|
0
0
0
A7
|
0
0
0
For more information, see the latest Management and Configuration Guide for your switch.
display lldp statistics
145
display lldp statistics global
Comware
Related ProVision
display lldp statistics global
show lldp stats
Displays global information about LLDP packets that are being advertised by the local system or
by remote systems. The statistics refer to significant events that involve LLDP packet transmission
and reception.
HP Switch# display lldp statistics global
LLDP statistics global information:
LLDP neighbor information last change time:33 days,19 hours,39
minutes,37 seconds
The number of LLDP neighbor information inserted : 10
The number of LLDP neighbor information deleted
: 10
The number of LLDP neighbor information dropped
: 0
The number of LLDP neighbor information aged out : 8
Example of Related ProVision Software Command Output.
HP Switch# show lldp stats
LLDP Device Statistics
Neighbor Entries List Last Updated : 2 hours
New Neighbor Entries Count : 20
Neighbor Entries Deleted Count : 20
Neighbor Entries Dropped Count : 0
Neighbor Entries AgeOut Count : 20
LLDP Port Statistics
Port
| NumFramesRecvd NumFramesSent NumFramesDiscarded
------ + -------------- ------------- -----------------A1
|
97317
97843
0
A2
|
21
12
0
A3
|
0
0
0
A4
|
446
252
0
A5
|
0
0
0
A6
|
0
0
0
A7
|
0
0
0
For more information, see the latest Management and Configuration Guide for your switch.
146
Display Commands
display lldp statistics interface interface-type interface-number
Comware
Related ProVision
display lldp statistics interface interface-type
interface-number
show lldp stats
Displays information about LLDP packets on a particular interface that are being advertised by the
local system or by remote systems. The statistics refer to significant events that involve LLDP packet
transmission and reception.
HP Switch# display lldp statistics interface 1
LLDP statistics information of port 1 [GigabitEthernet1/0/1]:
The number of LLDP frames transmitted
: 1713
The number of LLDP frames received
: 1200
The number of LLDP frames discarded
: 0
The number of LLDP error frames
: 1200
The number of LLDP TLVs discarded
: 1200
The number of LLDP TLVs unrecognized
: 0
The number of LLDP neighbor information aged out : 1
The number of CDP frames transmitted
: n/a
The number of CDP frames received
: n/a
The number of CDP frames discarded
: n/a
The number of CDP error frames
: n/a
Example of Related ProVision Software Command Output.
HP Switch# show lldp stats
LLDP Device Statistics
Neighbor Entries List Last Updated : 2 hours
New Neighbor Entries Count : 20
Neighbor Entries Deleted Count : 20
Neighbor Entries Dropped Count : 0
Neighbor Entries AgeOut Count : 20
LLDP Port Statistics
Port
| NumFramesRecvd NumFramesSent NumFramesDiscarded
------ + -------------- ------------- -----------------A1
|
97317
97843
0
A2
|
21
12
0
A3
|
0
0
0
A4
|
446
252
0
A5
|
0
0
0
A6
|
0
0
0
A7
|
0
0
0
For more information, see the latest Management and Configuration Guide for your switch.
display lldp statistics interface interface-type interface-number
147
display lldp status
Comware
Related ProVision
display lldp status
No equivalent ProVision software command
Displays information about Link Layer Discovery Protocol (LLDP) and Link Level Discovery
Protocol-Media Endpoint Discovery (LLDP-MED) configuration and capabilities on the switch. LLDP
and LLDP-MED are used to learn about and to distribute device information on network links. This
command shows information on global level as well as the interface level.
HP Switch# display lldp status
The current number of LLDP neighbors: 0
The current number of CDP neighbors: 0
LLDP neighbor information last changed time: 33 days,19 hours,39
minutes,37 seconds
Transmit interval
: 30s
Hold multiplier
: 4
Reinit delay
: 2s
Transmit delay
: 2s
Trap interval
: 5s
Fast start times
: 3
148
Port 1 [GigabitEthernet1/0/1]:
Port status of LLDP
Admin status
Trap flag
Polling interval
:
:
:
:
Enable
Tx_Rx
No
0s
Number
Number
Number
Number
Number
:
:
:
:
:
0
0
0
0
0
of
of
of
of
of
Display Commands
neighbors:
MED neighbors
CDP neighbors
sent optional TLV
received unknown TLV
display lldp status interface interface-type interface number
Comware
Related ProVision
display lldp status interface interface-type interface number No equivalent ProVision software command
Displays information about Link Layer Discovery Protocol (LLDP) and Link Level Discovery
Protocol-Media Endpoint Discovery (LLDP-MED) configuration and capabilities on the switch. LLDP
and LLDP-MED are used to learn about and to distribute device information on network links.
HP Switch# display lldp status interface 1
Port 1 :
Port status of LLDP
Admin status
Trap flag
Polling interval
:
:
:
:
Number
Number
Number
Number
Number
:
:
:
:
of
of
of
of
of
neighbors
MED neighbors
CDP neighbors
sent optional TLV
received unknown TLV
Enable
Tx_Rx
No
0s
0
0
0
0
0
Minimum Software Version: 15.10.
display lldp status interface interface-type interface number
149
display lldp tlv-config interface interface-type interface-number
Comware
Related ProVision
display lldp tlv-config interface interface-type
interface-number
No equivalent ProVision software command
LLDP information is sent by devices from each of their interfaces at a fixed interval in the form of
an Ethernet frame. Each frame contains one Link Layer Discovery Protocol Data Unit (LLDPDU).
Each LLDPDU is a sequence of typelength- value (TLV) structures. Each LLDP frame starts with the
following mandatory TLVs: Chassis ID, Port ID, and Time-to-Live. The mandatory TLVs are followed
by any number of optional TLVs. All Optional TLVs can be configured per port basis and can be
displayed with the help of this command for a particular interface.
HP Switch# display lldp tlv-config
LLDP tlv-config of port 98[GigabitEthernet2/0/2]:
NAME
STATUS
DEFAULT
Basic optional TLV:
Port Description TLV
YES
YES
System Name TLV
YES
YES
System Description TLV
YES
YES
System Capabilities TLV
YES
YES
Management Address TLV
YES
YES
IEEE
Port
Port
VLAN
150
802.1 extend TLV:
VLAN ID TLV
And Protocol VLAN ID TLV
Name TLV
YES
YES
YES
YES
YES
YES
IEEE 802.3 extend TLV:
MAC-Physic TLV
Power via MDI TLV
Link Aggregation TLV
Maximum Frame Size TLV
YES
YES
YES
YES
YES
YES
YES
YES
LLDP-MED extend TLV:
Capabilities TLV
Network Policy TLV
Location Identification TLV
Extended Power via MDI TLV
Inventory TLV
YES
YES
NO
YES
YES
YES
YES
NO
YES
YES
Display Commands
display local-proxy-arp
Comware
Related ProVision
display local-proxy-arp
show ip
Displays the status of the local proxy ARP. If an interface is specified, the local proxy ARP status
of the specified interface is displayed. If no interface is specified, the local proxy ARP status of all
interfaces is displayed.
HP Switch(config)# display local-proxy-arp
VLAN30
Local Proxy ARP status: disabled
VLAN33
Local Proxy ARP status: disabled
Operating Notes
For more information, see the “IP Routing Features” chapter in the latest Multicast and Routing
Guide for your switch.
Minimum Software Version: 15.11.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip
Internet (IP) Service
IP Routing : Disabled
Default TTL
Arp Age
Domain Suffix
DNS server
: 64
: 20
:
:
VLAN
-------------------DEFAULT_VLAN
VLAN2100
|
+
|
|
IP Config IP Address
Subnet Mask
Proxy ARP
---------- --------------- --------------- --------DHCP/Bootp 15.255.157.54
255.255.248.0
Yes Yes
Disabled
display local-proxy-arp
151
display logfile buffer
Comware
Related ProVision
display logfile buffer
show logging
Displays system log information.
HP Switch# display logfile buffer
%@00061%Jan 01 00:00:47 2090 system: -------------------------%@00062%Jan 01 00:00:47 2090 system: Mgmt Module 1 went down
without saving crash information
%@03002%Jan 01 00:00:47 2090 system: System reboot due to Reset
Switch
%@02759%Jan 01 00:00:47 2090 chassis: Savepower LED timer is
OFF.
%@00433%Jan 01 00:00:47 2090 ssh: Ssh server enabled
%@00092%Jan 01 00:00:47 2090 dhcp: Enabling Auto Image Config
Download via DHCP and turning off auto-tftp if enabled
%@00690%Jan 01 00:00:48 2090 udpf: DHCP relay agent feature
enabled
%@02637%Jan 01 00:00:48 2090 srcip: TACACS admin policy is
'outgoing interface'
%@02638%Jan 01 00:00:48 2090 srcip: TACACS oper policy is
'outgoing interface'
%@02637%Jan 01 00:00:48 2090 srcip: RADIUS admin policy is
'outgoing interface'
%@02638%Jan 01 00:00:48 2090 srcip: RADIUS oper policy is
'outgoing interface'
%@02637%Jan 01 00:00:48 2090 srcip: SYSLOG admin policy is
'outgoing interface'
%@02638%Jan 01 00:00:48 2090 srcip: SYSLOG oper policy is
'outgoing interface'
%@02637%Jan 01 00:00:48 2090 srcip: TELNET admin policy is
'outgoing
Example of Related ProVision Software Command Output.
HP Switch# show logging
Keys: W=Warning I=Information
M=Major D=Debug E=Error
---- Event Log listing: Events Since Boot ---I 10/28/09 21:45:42 00061 system: AM1: -----------------------I 10/28/09 21:45:42 00062 system: AM1: Mgmt Module 1 went down
without saving crash information
M 10/28/09 21:45:42 03002 system: AM1: System reboot due to
Reset Switch
I 10/28/09 21:45:42 02759 chassis: AM1: Savepower LED timer is
OFF.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
A configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
B configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
C configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
D configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
E configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
F configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
G configured ON.
152
Display Commands
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
H configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
I configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
J configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
K configured ON.
I 10/28/09 21:45:42 02751 chassis: AM1: LEDs for module in slot
L configured ON.
I 10/28/09 21:45:42 00937 chassis: AM1: Fabric 1 inserted
I 10/28/09 21:45:42 00937 chassis: AM1: Fabric 2 inserted
I 10/28/09 21:45:43 00092 dhcp: AM1: Enabling Auto Image Config
Download via DHCP and turning off auto-tftp if enabled
I 10/28/09 21:45:43 00690 udpf: AM1: DHCP relay agent feature
enabled
I 10/28/09 21:45:43 02637 srcip: AM1: TACACS admin policy is
'outgoing interface'
I 10/28/09 21:45:43 02638 srcip: AM1: TACACS oper policy is
'outgoing interface'
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display logfile buffer
153
display loopback-detection
Comware
Related ProVision
display loopback-detection
No equivalent ProVision software command
Displays the operating status of the loopback detection function. Field Descriptions
HP Switch(config)# display loopback-detection
Loopback-detection is running.
Detection interval is 30 second(s).
Action mode: None
Loopback-detection is enabled on the following VLAN(s):
1, 20, 315, 1001, 2008, 2010-2015, 2026
Loopback is detected on the following interface(s):
1
2
3
10
Field Descriptions
Detection Interval: Loopback detection interval in seconds.
Action Mode: The loopback detection action:
•
None—When detecting a looped port, the system prints log information and sends trap
messages.
•
Shutdown—When detecting a looped port, the system prints log information, sends trap
messages, and shuts down the port.
There is no related ProVision command.
154 Display Commands
display mac-address
Comware
Related ProVision
display mac-address
show mac-address
Displays information about the MAC address table.
HP Switch# display mac-address
MAC ADDR
VLAN ID STATE
PORT
001635-22ca40
1
Learned
001635-22ca7f
1
Learned
001122-334455
2
Config static
INDEX
A1
A1
A2
AGING TIME(s)
AGING
AGING
NOAGED
--- 3 mac address(es) found ---
Example of Related ProVision Software Command Output.
HP Switch# show mac-address 000009-21ae04
Status and Counters - Address Table - 080009-21ae84
MAC Address : 080009-21ae84
Locate on Port : A2
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display mac-address
155
display mac-address aging-time
Comware
Related ProVision
display mac-address aging-time
show system information
Displays the aging time of dynamic entries in the MAC address table.
HP Switch# display mac-address aging-time
Mac address aging time: 300s
Field Descriptions
Mac address aging time: Aging time of dynamic entries in the MAC address table.
Operating Notes
Comware displays mac-address as 1234-1234-1234 and ProVision displays it as 123456-123456.
For more information about MAC aging time, see the "Interface Access and System Information"
chapter in the latest Basic Operation Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# show system information
Status and Counters
System Name
System Contact
System Location
- General System Information
: HP Switch
:
:
MAC Age Time (sec) : 300
Time Zone
: 0
Daylight Time Rule : None
display mac-address aging-time Field Mappings.
156
Comware
ProVision Software
Mac address aging time
MAC Age Time (sec)
Display Commands
display mac-address multicast
Comware
Related ProVision
display mac-address multicast
No equivalent ProVision software command
Displays static multicast MAC address entries.
HP Switch# display mac-address multicast
MAC ADDR
VLAN ID STATE
PORT INDEX
010122-334455 1
Multicast
A1
012222-334455 1
Multicast
F24
AGING TIME(s)
NOAGED
NOAGED
--- 2 mac address(es) found ---
Minimum Software Version: 15.10.
display mac-address multicast
157
display mac-authentication
Comware
Related ProVision
display mac-authentication [interface]
show port-access mac-based
Displays MAC authentication settings and statistics, including the global settings, and port-specific
settings and MAC authentication and online user statistics.
If you specify a list of ports, the command displays port-specific settings and statistics only for the
specified ports.
If you do not specify any port, the command displays port-specific settings and statistics for all
ports.
HP Switch(config)# display mac-authentication
MAC address authentication is n/a
User name format is no-delimiter like aabbccddeeff
Fixed Username:n/a
Fixed password:not configured
Offline detect period is 0s
Quiet period is 0s
Server response timeout value is 0s
The max allowed user number is n/a per slot
Current user number amounts to 0
Current domain: n/a
Silent MAC User info:
MAC Addr
n/a
From Port
n/a
A1 is link-up
MAC address authentication is disabled
Authenticate success: n/a, failed: n/a
Max number of on-line users is 1
Current online user number is 0
MAC Addr
Authenticate state
A2 is link-down
MAC address authentication is disabled
Authenticate success: n/a, failed: n/a
Max number of on-line users is 1
Current online user number is 0
MAC Addr
Authenticate state
Port Index
n/a
AuthIndex
AuthIndex
Field Descriptions
MAC address authentication is enabled: Whether MAC authentication is enabled.
User name format is no-delimiter like no delimiter format: Type of user account, which can be
MAC-based or shared. If MAC-based accounts are used, this field displays "User name format is
MAC address &mldr;" and the format settings for usernames and passwords. For example, MAC
addresses without hyphens in lower case. If a shared account is used, this field displays "User
name format is fixed account."
Fixed username: Username of the shared account for MAC authentication users. If MAC-based
accounts are used, this field displays mac.
Fixed password: Password of the shared account for MAC authentication users. If MAC-based
accounts are used, this field displays not configured.
Offline detect period: Setting of the offline detect timer.
Server response timeout value: Setting of the server timeout timer.
158
Display Commands
The max allowed user number: Maximum number of users each slot supports.
Current user number amounts to: Number of online users.
Current domain: not configured, use default domain: Authentication domain that is currently used.
Silent Mac User info: Information about silent MAC addresses. A MAC address is marked silent
when it fails a MAC authentication, and at the same time, a quiet timer starts. Before the timer
expires, the device drops any packet from the MAC address and does not perform MAC
authentication for the MAC address.
GigabitEthernet3/0/1 is link-up: Status of the link on port GigabitEthernet 3/0/1. In this example,
the link is up.
MAC address authentication is enabled: Whether MAC authentication is enabled on port
GigabitEthernet 3/0/1.
Authenticate success: 0, failed: 0: MAC authentication statistics, including the number of successful
and unsuccessful authentication attempts.
Current online user number: Number of online users on the port.
MAC Addr: MAC address of the online user.
Authenticate state: User status. Possible values include the following:
•
CONNECTING—The user is logging in.
•
SUCCESS—The user has passed the authentication.
•
FAILURE—The user failed the authentication.
•
LOGOFF—The user has logged off.
AuthIndex: Authenticator index.
Operating Notes
For more information on switch MAC authentication operation, see the "Web and MAC
Authentication" chapter in the latest Access Security Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show port-access mac-based
Port Access
Auth
Port Clients
---- ------1
1
2
2
3
4
MAC-Based Status
Unauth Untagged
Clients VLAN
------- -------1
2003
0
MACbased
0
1
Tagged
VLANs
-----Yes
No
Yes
Port
COS
-------70000000
Yes
No
% In
Limit
-----100
Yes
No
RADIUS
ACL
-----Yes
Yes
No
display mac-authentication [interface] Field Mappings.
Comware
ProVision Software
MAC address authentication is enabled
n/a
User name format is MAC address in lowercase, like
xxxxxxxxxxxx
n/a
Fixed username
n/a
Fixed password
n/a
Offline detect period
n/a
Quiet period
n/a
Server response timeout value
n/a
display mac-authentication
159
Comware
ProVision Software
the max allowed user number
n/a
Current user number amounts to
n/a
Current domain: not configured, use default domain
n/a
Silent Mac User info
n/a
GigabitEthernet3/0/1 is link-up
n/a
MAC address authentication is enabled
n/a
Authenticate success: 0, failed: 0
n/a
Current online user number
n/a
MAC Addr
n/a
Authenticate state
n/a
AuthIndex
n/a
160 Display Commands
display mac-authentication [interface …]
Comware
Related ProVision
display mac-authentication [interface ...]
show port-access mac-based
Displays MAC authentication settings and statistics.
HP Switch# display mac-authentication interface configuration
MAC address authentication is n/a
User name format is no-delimiter like aabbccddeeff
Fixed Username:n/a
Fixed password:not configured
Offline detect period is 0s
Quiet period is 0s
Server response timeout value is 0s
The max allowed user number is n/a per slot
Current user number amounts to 0
Current domain: n/a
Silent MAC User info:
MAC Addr
From Port
Port Index
n/a
n/a
n/a
A1 is link-up
MAC address authentication is disabled
Authenticate success: n/a, failed: n/a
Max number of on-line users is 1
Current online user number is 0
MAC Addr
Authenticate state
AuthIndex
A2 is link-down
MAC address authentication is disabled
Authenticate success: n/a, failed: n/a
Max number of on-line users is 1
Current online user number is 0
MAC Addr
Authenticate state
AuthIndex
Example of Related ProVision Software Command Output.
HP Switch# show port-access mac-based config
Port Access MAC-Based Configuration
MAC Address Format : no-delimiter
Password : secretMAC1
Unauth Redirect Configuration URL :
Unauth Redirect Client Timeout (sec) : 1800
Unauth Redirect Restrictive Filter : Disabled
Total Unauth Redirect Client Count : 0
Client Client Logoff Re-Auth Unauth Auth
Cntrl
Port Enabled Limit Moves Period Period VLAN ID VLAN ID
---- ------- ------ ------ ------- ------- ------- -------1
No
1
No
300
0
0
0
2
No
1
No
300
0
0
0
3
No
1
No
300
0
0
0
4
No
1
No
300
0
0
0
5
No
1
No
300
0
0
0
6
No
1
No
300
0
0
0
7
No
1
No
300
0
0
0
8
No
1
No
300
0
0
0
Dir
----both
both
both
both
both
both
both
both
display mac-authentication [interface …]
161
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
162
Display Commands
display memory
Comware
Related ProVision
display memory
show system information
Displays the current memory usage on the switch.
HP Switch(config)# display memory
System Total Memory(bytes): 128090112
Total Used Memory(bytes): 47385504
Used Rate: 36%
Field Descriptions
System Total Memory (bytes): Total system memory in the switch.
Total Used Memory (bytes): Total system memory in use.
Used Rate: Percentage of system memory in use.
Operating Notes
To display memory usage in ProVision Software, use the following command:
HP Switch# show system information
This command lists the total memory and free memory available in the switch, along with other
system-related information.
For more on system information, refer to the “Interface Access and System Information” chapter in
the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch# show system information
Status and Counters - General System Information
System Name
System Contact
System Location
: HP Switch
:
:
MAC Age Time (sec) : 300
Time Zone
: -480
Daylight Time Rule : Continental-US-and-Canada
Software revision : K.15.08.0003
ROM Version
: K.15.27
Allow V1 Modules : Yes
Base MAC Addr
Serial Number
Opacity Shields
Up Time
CPU Util (%)
Memory
- Total
Free
Packet
Buffers
- Total
Free
Lowest
Missed
: 3 hours
: 0
IP Mgmt - Pkts Rx : 126,890
Pkts Tx : 5123
: 001871-c42f00
: SG641SU00L
: Not Installed
: 128,040,960
: 80,694,816
:
:
:
:
6750
5086
5051
0
display memory
163
display mld group
Comware
Related ProVision
display mld group
show ipv6 mld
Displays the number of active MLD (Multicast Listener Discovery) groups and the VLAN and IPv6
address on which each group is active.
HP Switch# display mld group
Total 4 MLD Group(s).
Interface group report information
Vlan-Interface1(1234:1::5):
Total 1 MLD Groups reported
Group Address : ff1e::1
Last Reporter : fe80::200:f7ff:fe95:4f5d
Uptime : 00:45:00
Expires : 00:03:20
Vlan-Interface2(1234:3::5):
Total 2 MLD Groups reported
Group Address : ff1e::3
Last Reporter : fe80::200:f7ff:fe95:da95
Uptime : 00:43:28
Expires : 00:03:16
Group Address : ff1e::4
Last Reporter : fe80::200:f7ff:fe95:da95
Uptime : 00:43:28
Expires : 00:03:16
Vlan-Interface10(1234:2::5):
Total 1 MLD Groups reported
Group Address : ff1e::5
Last Reporter : fe80::200:f7ff:fe95:9c92
Uptime : 00:43:41
Expires : 00:03:20
Field Descriptions
Total n MLD Groups: The total number of MLD groups detected on the switch.
VLAN-interface< id > ( < ipv6-addr > ): A specific VLAN interface.
Total n MLD Groups reported: The number of MLD groups detected on the indicated VLAN.
Group Address: The IPv6 address of an MLD group detected on the indicated VLAN.
•
Last Reporter: The IPv6 address of the host that last reported membership for the group.
•
Uptime: Length of time since the IPv6 multicast group was joined.
•
Expires: Time remaining for the IPv6 multicast group.
Operating Notes
The display mld group command reports on MLD traffic on static VLANs.
The switch supports MLDv1 and MLDv2.
To enable MLD operation in ProVision software, use the following command in a VLAN configuration
context:
ipv6 mld < enable | disable >
For example:
HP Switch(vlan-10)# ipv6 mld enable
164 Display Commands
For more on MLD, including additional MLD commands, see the “Multicast Listener Discovery
(MLDv1 and MLDv2)” chapter in the latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 mld
MLD Service Protocol Info
Total vlans with MLD enabled
Current count of multicast groups joined
VLAN ID : 1
MLD Version : 2
: 2
: 2
NAME : DEFAULT_VLAN
MLD Interface State : Querier
Querier Address
: fe80::218:71ff:fec4:2f00 [this switch]
Version
: 2
Uptime
: 11m 55s
Expires
: 1m 5s
Ports with multicast routers :
Active Group Addresses
Tracking Vers Mode Uptime
Expires
---------------------------------------- -------- ---- ---- -------- -------ff3e:30:2001:db8:8:0:7:101
Filtered 2
EXC 20h 55m 22h 50m
VLAN ID : 2
MLD Version : 2
NAME : VLAN2
MLD Interface State : Non-Querier
Querier Address
: ::
Version
: Uptime
: Expires
: Ports with multicast routers :
Active Group Addresses
Tracking Vers Mode Uptime
Expires
---------------------------------------- -------- ---- ---- -------- -------ff33:30:2001:db8:8:0:7:102
Filtered 2
INC 10m 40s 12m 17s
display mld group
165
display mld group interface vlan-interface <vid>
Comware
Related ProVision
display mld group interface vlan-interface <vid>
show ipv6 mld vlan <vid>
Displays information of all MLD groups.
HP Switch# display mld group interface vlan-interface 30
Interface group report information
Vlan-Interface30(2075:1:1:30::1):
Total 5 MLD Groups reported
Group : ff02::2
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:02:18
Group : ff02::16
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:02:26
Group : ff02::1:ff00:0
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:02:26
Group : ff02::1:ff00:3
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:02:17
Group : ff02::1:ffab:9300
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:02:24
Field Descriptions
Group: Multicast group address
Last reporter: Address of the last host that reported its membership for this multicast group
Uptime: Length of time since the multicast group was reported
Expires: Remaining time of the multicast group
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ipv6 mld vlan <vid>" on page
2-109.
166 Display Commands
display mld group interface vlan-interface <vid> verbose
Comware
Related ProVision
display mld group interface vlan-interface <vid> verbose show ipv6 mld vlan <vid>
Displays information of all MLD groups.
HP Switch# display mld group interface vlan-interface 30 verbose
Interface group report information
Vlan-Interface30(2075:1:1:30::1):
Total 5 MLD Groups reported
Group : ff02::2
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:04:00
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Group : ff02::16
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:54
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Group : ff02::1:ff00:0
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:53
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Group : ff02::1:ff00:3
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:58
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Group : ff02::1:ffab:9300
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:56
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Field Descriptions
Interface group report information: MLD group information on the interface
Total 5 MLD Groups reported: Five MLD groups were reported.
Group: IPv6 multicast group address
Uptime: Length of time since the IPV6 multicast group was joined
Expires: Remaining time of the IPv6 multicast group, where "off" means that the multicast group
never times out
display mld group interface vlan-interface <vid> verbose
167
Last reporter: IPv6 address of the host that last reported membership for this group
Last-listener-query-counter: Number of MLD last listener queries sent
Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where "off"
means that the timer never times out
Group mode: Multicast source filtering mode:
•
include
•
exclude
This field is displayed only when the device is running MLDv2.
Version1-host-present-timer-expiry: Remaining time of the MLDv1 host present timer, where "off"
means that the timer never times out.
This field is displayed only when the device is running MLDv2.
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ipv6 mld vlan <vid> " on page
2-109.
168 Display Commands
display mld group port-info vlan <vlan-id> display mld group port-info
Comware
Related ProVision
display mld group port-info vlan <vlan-id>
No equivalent ProVision software command
display mld group port-info
Displays Layer 2 port information of MLD groups, including Layer 2 information of dynamic and
static MLD group entries.
HP Switch# display mld group port-info
Total 1 IP Group(s).
Total n/a IP Source(s).
Total n/a MAC Group(s).
Port flags: D-Dynamic port, S-Static port, C-Copy port
Subvlan flags: R-Real VLAN, C-Copy VLAN
Vlan(id):100.
Total 3 IP Group(s).
Total n/a IP Source(s).
Total n/a MAC Group(s).
Router port(s):total 0 port(s).
IP group(s):the following ip group(s) match to one mac group.
IP group address:FF13::1
(::, FF13::1):
Host port(s):total 1 port(s).
GE2/0/1 (D)
MAC group(s): n/a
HP Switch# display mld group port-info vlan 100
Total 1 IP Group(s).
Total n/a IP Source(s).
Total n/a MAC Group(s).
Port flags: D-Dynamic port, S-Static port, C-Copy port
Subvlan flags: R-Real VLAN, C-Copy VLAN
Vlan(id):100.
Total 3 IP Group(s).
Total n/a IP Source(s).
Total n/a MAC Group(s).
Router port(s):total 0 port(s).
IP group(s):the following ip group(s) match to one mac group.
IP group address:FF13::1
(::, FF13::1):
Host port(s):total 1 port(s).
A1 (D)
MAC group(s): n/a
Minimum Software Version: 15.10.
display mld group port-info vlan <vlan-id> display mld group port-info
169
display mld group verbose
Comware
Related ProVision
display mld group verbose
show ipv6 mld vlan <vid>
Displays information about dynamically added MLD groups on all interfaces.
HP Switch# display mld group verbose
Total 5 MLD Group(s).
Interface group report information
Vlan-Interface30(2075:1:1:30::1):
Total 5 MLD Groups reported
Group : ff02::2
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:31
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Group : ff02::16
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:26
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Group : ff02::1:ff00:0
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:24
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Group : ff02::1:ff00:3
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:30
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Group : ff02::1:ffab:9300
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:03:28
Group mode : exclude
Version1-host-present-timer-expiry : on
Last-listener-query-counter : n/a
Last-listener-query-timer-expiry : n/a
Field Descriptions
Interface group report information: MLD group information on the interface
Total 1 MLD Groups reported: One MLD group was reported.
Group: IPv6 multicast group address
Uptime: Length of time since the IPV6 multicast group was joined
170
Display Commands
Expires: Remaining time of the IPv6 multicast group, where "off" means that the multicast group
never times out
Last reporter: IPv6 address of the host that last reported membership for this group
Last-listener-query-counter: Number of MLD last listener queries sent
Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where "off"
means that the timer never times out
Group mode: Multicast source filtering mode:
•
include
•
exclude
This field is displayed only when the device is running MLDv2.
Version1-host-present-timer-expiry: Remaining time of the MLDv1 host present timer, where "off"
means that the timer never times out.
This field is displayed only when the device is running MLDv2.
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ipv6 mld vlan <vid> " on page
2-109.
display mld group verbose
171
display mld group x:x::x:x
Comware
Related ProVision
display mld group x:x::x:x
show ipv6 mld vlan <vid>
Displays information of all MLD groups.
HP Switch# display mld group ff02::2
Interface group report information
Interface:Vlan30
Last Reporter : fe80::3e4a:92ff:feab:9300
Uptime : 5 ...
Expires : 00:02:38
Field Descriptions
Group: Multicast group address
Last reporter: Address of the last host that reported its membership for this multicast group
Uptime: Length of time since the multicast group was reported
Expires: Remaining time of the multicast group
Example of Related ProVision Software Command Output.
There is no equivalent ProVision command.
HP Switch# show ipv6 mld vlan 30
MLD Service Protocol Info
VLAN ID : 30 NAME : VLAN30
MLD Version : 2
MLD Interface State : Non-Querier
Querier Address : fe80::3e4a:92ff:feab:9300
Port
: A2
Version
: 2
Uptime
: 5d 18h 38m
Expires
: 3m 48s
Ports with multicast routers : A2
Active Group Addresses Tracking Vers Mode Uptime Expires
----------------------- ------- ---- ---- -------- ----ff02::2
Standard 1
EXC 5d 18... 2m 30s
ff02::16
Standard 1
EXC 5d 18... 2m 33s
ff02::1:ff00:0
Standard 1
EXC 5d 18... 2m 28s
ff02::1:ff00:3
Standard 1
EXC 5d 18... 2m 27s
ff02::1:ffab:9300
Standard 1
EXC 5d 18... 2m 24s
172
Display Commands
display mld group x:x::x:x verbose
Comware
Related ProVision
display mld group x:x::x:x verbose
show ipv6 mld vlan <vid>
Displays information of all MLD groups.
HP Switch# display mld group verbose
Interface group report information
Vlan-interface100(FE80::101)
Total 1 MLD Groups reported
Group: FF03::101
Uptime: 00:01:46
Expires: 00:01:30
Last reporter: FE80::10
Last-listener-query-counter: 0
Last-listener-query-timer-expiry: off
Group mode: include
Version1-host-present-timer-expiry: off
Field Descriptions
Interface group report information: MLD group information on the interface
Total 1 MLD Groups reported: One MLD group was reported.
Group: IPv6 multicast group address
Uptime: Length of time since the IPV6 multicast group was joined
Expires: Remaining time of the IPv6 multicast group, where "off" means that the multicast group
never times out
Last reporter: IPv6 address of the host that last reported membership for this group
Last-listener-query-counter: Number of MLD last listener queries sent
Last-listener-query-timer-expiry: Remaining time of the MLD last listener query timer, where "off"
means that the timer never times out
Group mode: Multicast source filtering mode:
•
include
•
exclude
This field is displayed only when the device is running MLDv2.
Version1-host-present-timer-expiry: Remaining time of the MLDv1 host present timer, where "off"
means that the timer never times out.
This field is displayed only when the device is running MLDv2.
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ipv6 mld vlan <vid> " on page
2-109.
display mld group x:x::x:x verbose
173
display mld interface
Comware
Related ProVision
display mld interface
show ipv6 mld vlan <vid>
Displays MLD configuration and operation information on the specified interface or all MLD-enabled
interfaces.
HP Switch# display mld interface
Interface information
Vlan-Interface30(2075:1:1:30::1):
MLD is enabled
Current MLD version is 2
Value of query interval for MLD(in seconds) : 125
Value of other querier present interval for MLD(in seconds) : 255
Value of maximum query response time for MLD(in seconds) : 10
Querier for MLD : fe80::3e4a:92ff:feab:9300
Total 5 MLD Groups reported
Field Descriptions
Vlan-interface30 (2075:1:1:30::1): Interface and IPv6 link-local address
Current MLD version: MLD version running on the interface
Value of query interval for MLD (in seconds): MLD query interval, in seconds
Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in
seconds
Value of maximum query response time for MLD (in seconds): Maximum response delay for general
query messages (in seconds)
Querier for MLD: IPv6 link-local address of the MLD querier
Total 5 MLD Groups reported: Total number of MLD groups the interface has dynamically joined
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ipv6 mld vlan <vid> " on page
2-109.
174
Display Commands
display mld interface verbose
Comware
Related ProVision
display mld interface verbose
show ipv6 mld vlan <vid>
Displays MLD configuration and operation information on the specified interface or all MLD-enabled
interfaces.
HP Switch# display mld interface verbose
Interface information
Vlan-Interface30(2075:1:1:30::1):
MLD is enabled
Current MLD version is 2
Value of query interval for MLD(in seconds) : 125
Value of other querier present interval for MLD(in seconds)
: 255
Value of maximum query response time for MLD(in seconds) : 10
Querier for MLD : fe80::3e4a:92ff:feab:9300
Value of last listener query interval(in seconds) : 1
Value of startup query interval(in seconds) : 31
Value of startup query count : 2
General query timer expiry (hours:minutes:seconds) : 00:03:19
MLD activity : 19861 joins, 0 leaves
Multicast ipv6 routing on this interface : n/a
Robustness : 2
Require-router-alert : enabled
Fast-leave : enabled
Ssm-mapping : n/a
Startup-query-timer-expiry : off
Other-querier-present-timer-expiry : on
Proxying interface : n/a
Field Descriptions
Vlan-Interface30(2075:1:1:30::1): Interface and IPv6 link-local address
Current MLD version: MLD version running on the interface
Value of query interval for MLD (in seconds): MLD query interval, in seconds
Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in
seconds
Value of maximum query response time for MLD (in seconds): Maximum response delay for general
query messages (in seconds)
Value of last listener query interval (in seconds): MLD last listener query interval, in seconds
Value of startup query interval(in seconds): MLD startup query interval, in seconds
Value of startup query count: Number of MLD general queries sent on startup
General query timer expiry: Remaining time of the MLD general query timer, where "off" means
that the timer never times out
Querier for MLD: IPv6 link-local address of the MLD querier
MLD activity: MLD activity statistics (number of join and done messages)
Robustness: MLD querier&rsquo;s robustness variable
Require-router-alert: Dropping MLD messages without Router-Alert (enabled/ disabled)
Fast-leave: MLD fast leave processing status (enabled/disabled)
Ssm-mapping: MLD SSM mapping status (enabled/disabled)
display mld interface verbose
175
Startup-query-timer-expiry: Remaining time of MLD startup query timer, where "off" means that
the timer never times out
Other-querier-present-timer-expiry: Remaining time of MLD other querier present timer, where
"off" means that the timer never times out
Proxying interface: The MLD proxy interface, where "none" means that no proxy interface exists
MLD proxy is enabled: MLD proxying is enabled
Version1-querier-present-timer-expiry: Remaining time of the MLDv1 querier present timer, where
"off" means that the timer never times out
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ipv6 mld vlan <vid> " on page
2-109.
176
Display Commands
display mld interface vlan-interface <vid>
Comware
Related ProVision
display mld interface vlan-interface <vid>
show ipv6 mld vlan <vid>
Displays MLD configuration and operation information on the specified interface or all MLD-enabled
interfaces.
HP Switch# display mld interface vlan-interface 30
Vlan-Interface30(2075:1:1:30::1):
MLD is enabled
Current MLD version is 2
Value of query interval for MLD(in seconds) : 125
Value of other querier present interval for MLD(in seconds)
: 255
Value of maximum query response time for MLD(in seconds) : 10
Querier for MLD : fe80::3e4a:92ff:feab:9300
Total 5 MLD Groups reported
Field Descriptions
Vlan-Interface30(2075:1:1:30::1): Interface and IPv6 link-local address
Current MLD version: MLD version running on the interface
Value of query interval for MLD (in seconds): MLD query interval, in seconds
Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in
seconds
Value of maximum query response time for MLD (in seconds): Maximum response delay for general
query messages (in seconds)
Querier for MLD: IPv6 link-local address of the MLD querier
Total 5 MLD Groups reported: Total number of MLD groups the interface has dynamically joined
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ipv6 mld vlan <vid> " on page
2-109.
display mld interface vlan-interface <vid> 177
display mld interface vlan-interface <vid> verbose
Comware
Related ProVision
display mld interface vlan-interface <vid> verbose
show ipv6 mld vlan <vid>
Displays MLD configuration and operation information on the specified interface or all MLD-enabled
interfaces.
HP Switch# display mld interface vlan-interface 30 verbose
Vlan-Interface30(2075:1:1:30::1):
MLD is enabled
Current MLD version is 2
Value of query interval for MLD(in seconds) : 125
Value of other querier present interval for MLD(in seconds)
: 255
Value of maximum query response time for MLD(in seconds) : 10
Querier for MLD : fe80::3e4a:92ff:feab:9300
Value of last listener query interval(in seconds) : 1
Value of startup query interval(in seconds) : 31
Value of startup query count : 2
General query timer expiry (hours:minutes:seconds) : 00:02:38
MLD activity : 19866 joins, 0 leaves
Multicast ipv6 routing on this interface : n/a
Robustness : 2
Require-router-alert : enabled
Fast-leave : enabled
Ssm-mapping : n/a
Startup-query-timer-expiry : off
Other-querier-present-timer-expiry : on
Proxying interface : n/a
Total 5 MLD Groups reported
Field Descriptions
Vlan-interface100(FE80::200:AFF:FE01:101): Interface and IPv6 link-local address
Current MLD version: MLD version running on the interface
Value of query interval for MLD (in seconds): MLD query interval, in seconds
Value of other querier present interval for MLD (in seconds): MLD other querier present interval, in
seconds
Value of maximum query response time for MLD (in seconds): Maximum response delay for general
query messages (in seconds)
Value of last listener query interval (in seconds): MLD last listener query interval, in seconds
Value of startup query interval(in seconds): MLD startup query interval, in seconds
Value of startup query count: Value of startup query count:
General query timer expiry: Remaining time of the MLD general query timer, where "off" means
that the timer never times out
Querier for MLD: IPv6 link-local address of the MLD querier
MLD activity: MLD activity statistics (number of join and done messages)
Robustness: MLD querier&rsquo;s robustness variable
Require-router-alert: Dropping MLD messages without Router-Alert (enabled/ disabled)
Fast-leave: MLD fast leave processing status (enabled/disabled)
Ssm-mapping: MLD SSM mapping status (enabled/disabled)
178
Display Commands
Startup-query-timer-expiry: Remaining time of MLD startup query timer, where "off" means that
the timer never times out
Other-querier-present-timer-expiry: Remaining time of MLD other querier present timer, where
"off" means that the timer never times out
Proxying interface: The MLD proxy interface, where "none" means that no proxy interface exists
Total 1 MLD Group reported: Total number of MLD groups the interface has dynamically joined
MLD proxy is enabled: MLD proxying is enabled
Version1-querier-present-timer-expiry: Remaining time of the MLDv1 querier present timer, where
"off" means that the timer never times out
Example of Related ProVision Software Command Output.
There is no direct equivalent ProVision command. Please see "show ipv6 mld vlan <vid> " on page
2-109.
display mld interface vlan-interface <vid> verbose
179
display mld routing-table
Comware
Related ProVision
display mld routing-table
No equivalent ProVision software command
Displays information about the MLD routing table.
HP Switch# display mld routing-table
Routing table
Total 2 entries
00001. (*, 2ffd::1)
List of 2 downstream interfaces
Vlan-interface100 (fe80::3ee5:a6ff:fe18:1142),
Protocol: MLD
Vlan-interface200 (fe80::3ee5:a6ff:fe18:1143),
Protocol: MLD
00002. (2ffc::9, 2ffd::1)
List of 2 downstream interfaces in exclude mode
Vlan-interface100 (fe80::3ee5:a6ff:fe18:1142),
Protocol: MLD
Vlan-interface200 (fe80::3ee5:a6ff:fe18:1143),
Protocol: MLD
Minimum Software Version: 15.10.
180 Display Commands
display monitor-link group [group-number | all],
Comware
Related ProVision
display monitor-link group<group-number | all]
show uplink-failure-detection
Displays information about the specified or all monitor link groups.
HP Switch# display monitor-link group 2
Monitor link group 2 information:
Group status : NONE
Last-up-time : n/a
Last-down-time : n/a
Member
Role
Status
------------------------------------------3
UPLINK
DOWN
4
DOWNLINK DOWN
Field Descriptions
Monitor link group 1 information: Information about monitor link group 1.
Group status: Monitor link group state, which can be up or down or none.
Last-up-time: Last time when the monitor link group was up.
Last-down-time: Last time when the monitor link group was down.
Member: Member ports of the monitor link group.
Role: Port role, which can be uplink port or downlink port.
Status: Member link state, which can be up or down.
Operating Notes
In ProVision, groupid ranges from 1 to 64 whereas in H3C switches, groupid ranges from 1 to
24. For more information about link groups, see the "Port Status and Configuration" chapter in
the latest Management and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show uplink-failure-detection
Uplink Failure Detection Information
UFD Enabled : Yes
TRACK ID | Monitored Links Links to Disable LtM State LtD State
-------- + --------------- ---------------- --------- --------------3
5,6
3
Up
Up
4
13
4-5
Down
Auto-Disabled
display monitor-link group Field Mappings.
Comware
ProVision Software
Monitor link group
Track ID
Group status
UFD State
Last-up-time
n/a
Last-down-time
n/a
Member
Monitored Links/Links to Disable
display monitor-link group [group-number | all],
181
182
Comware
ProVision Software
Role
n/a
Status
LtMState/LtD State
Display Commands
display multicast forwarding-table
Comware
Related ProVision
display multicast forwarding-table
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays multicast forwarding table information. If neither all-instance nor vpn-instance is specified,
this command displays the information on the public network. Multicast forwarding tables guide
multicast forwarding. You can view the forwarding state of multicast traffic by checking the multicast
forwarding table.
HP Switch# display multicast forwarding-table
Multicast Forwarding Table of VPN-Instance: n/a
Total 1 entry
Total 1 entry matched
00001. (30.30.30.1, 239.1.1.1)
MID: n/a, Flags: 0x2:0
Uptime: 00:00:21, Timeout in: 00:00:02
Incoming interface: Vlan-interface10
List of 1 outgoing interfaces:
1: Vlan-interface20
Matched 2 packets(bytes n/a), Wrong If 0 packets
Forwarded 0 packets(0 bytes)
Minimum Software Version: 15.10.
display multicast forwarding-table 183
display multicast routing-table
Comware
Related ProVision
display multicast routing-table
show ip mroute
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays multicast routing table information. Multicast routing tables are the basis of multicast
forwarding. You can view the establishment state of an (S, G) entry by checking the multicast
routing table.
HP Switch# display multicast routing-table
Multicast routing table of VPN-Instance: public net
Total 1 entry,1 matched
00001. (20.20.20.2, 239.1.1.1)
Uptime: 00:00:20
Upstream Interface: 10
List of 1 downstream interfaces
1: Vlan-interface30
HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1
Multicast routing table of VPN-Instance: public net
Total 1 entry,1 matched
00001. (20.20.20.2, 239.1.1.1)
Uptime: 00:00:20
Upstream Interface: 10
List of 1 downstream interfaces
1: Vlan-interface30
HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1
incoming-interface Vlan-interface 20
Multicast routing table of VPN-Instance: public net
Total 1 entry,1 matched
00001. (20.20.20.2, 239.1.1.1)
Uptime: 00:00:20
Upstream Interface: 10
List of 1 downstream interfaces
1: Vlan-interface30
HP Switch# display multicast routing-table 20.20.20.1 239.1.1.1
incoming-interface Vlan-interface 20 outgoing-interface Vlaninterface
30
Multicast routing table of VPN-Instance: public net
Total 1 entry,1 matched
00001. (20.20.20.2, 239.1.1.1)
Uptime: 00:00:20
Upstream Interface: 10
List of 1 downstream interfaces
1: Vlan-interface30
Example of Related ProVision Software Command Output.
HP Switch# show ip mroute
IP Multicast Route Entries
Total number of entries : 2
Group Address
Source Address
Neighbor
VLAN
--------------- --------------- ----------- ---184 Display Commands
239.255.255.1
239.255.255.5
10.27.30.2
10.27.30.2
10.29.30.1
10.29.30.1
29
29
Operating Notes
For more information, refer to the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.10.
display multicast routing-table 185
display multicast routing-table static
Comware
Related ProVision
display multicast routing-table static
show ip pim rpf-override
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the information about multicast static routes.
HP Switch# display multicast routing-table static
Multicast Routing Table of VPN-Instance: n/a
Routes : n/a
Mroute 10.10.0.0/16
Interface = n/a
RPF Neighbor = 2.2.2.2
Matched routing protocol = <none>,Route-policy = <none>
Preference = n/a, Order = n/a
Running Configuration = rpf-override 10.10.10.10/32 10.10.10.1
Field Descriptions
Multicast Routing Table of VPN-Instance: public net: Multicast routing table for the public network
Mroute: Multicast route source address and its mask length
Interface: Outgoing interface to the multicast source
RPF Neighbor: IP address of the RPF neighbor through which the multicast source is reachable
Route-policy: Routing policy. The multicast source address of the route should match the routing
policy.
Preference: Route preference
Order: Sequence number of the route
Running Configuration: Command line that configures the multicast static route
Operating Notes
ProVision switches use a different command to define the static multicast routes, The corresponding
config command is displayed in the command. For more information on multicast static routes, see
the "PIM-SM (Sparse Mode)" or the "PIM-DM (Dense Mode) chapters in the latest Multicast and
Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip pim rpf-override
Static RPF Override
Multicast Source
------------------10.1.1.1/32
13.1.1.1/32
RPF IP Address
--------------11.2.2.1
12.1.1.1
display multicast routing-table static Field Mappings.
Comware
ProVision Software
Multicast Routing Table of VPN-Instance: public net
n/a
Mroute
n/a
186 Display Commands
Comware
ProVision Software
Interface
n/a
RPF Neighbor
RPF IP Address
Route-policy
n/a
Preference
n/a
Order
n/a
Running Configuration
n/a
display multicast routing-table static
187
display multicast rpf-info
Comware
Related ProVision
display multicast rpf-info
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays rpf override information of a multicast source.
HP Switch# display multicast rpf-info 10.10.10.10
RPF information about source 10.10.10.10:
VPN instance: n/a
RPF interface: Vlan-Interface 10
Referenced route/mask: 40.40.40.40/32
Referenced route type: n/a
Route selection rule: n/a
Load splitting rule: n/a
Minimum Software Version: 15.10.
188 Display Commands
display ospf cumulative
Comware
Related ProVision
display ospf cumulative
show ip ospf statistics
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPF statistics information.
HP Switch# display ospf cumulative
OSPF Process 1 with Router ID : 2.2.2.2
Cumulations
IO Statistics
Type
Hello
DB Description
Link-State Req
Link-State Update
Link-State Ack
Input
2
0
0
0
0
Output
2
2
0
0
0
LSAs originated by this router
Router: n/a
Network: n/a
Sum-Net: n/a
Sum-Asbr: n/a
External: n/a
NSSA: n/a
Opq-Link: n/a
Opq-Area: n/a
Opq-As: n/a
LSAs Originated: n/a
Routing Table:
Intra Area: n/a
LSAs Received: n/a
Inter Area: n/a
ASE/NSSA: n/a
Field Descriptions
IO Statistics: Statistics about input/output packets and LSAs.
Type: OSPF packet type.
Input: Packets received.
Output: Packets sent.
Hello: Hello packet.
DB Description: Database Description packet
Link-State Req: Link-State Request packet.
Link-State Update: Link-State Update:
Link-State-Ack: Link-State Acknowledge packet.
LSAs originated by this router: LSAs originated by this router.
Router: Number of Type-1 LSAs originated.
Network: Number of Type-2 LSAs originated.
Sum-Net: Number of Type-3 LSAs originated.
Sum-Asbr: Number of Type-4 LSAs originated.
display ospf cumulative 189
External: Number of Type-5 LSAs originated.
NSSA: Number of Type-7 LSAs originated.
Opq-Link: Number of Type-9 LSAs originated.
Opq-Area: Number of Type104 LSAs originated.
Opq-As: Number of Type-11 LSAs originated.
LSA originated: Number of LSAs originated.
LSA Received: Number of LSAs received.
Routing Table: Routing table information.
Intra Area: Intra-area route number.
Inter Area: Inter-area route number.
ASE: ASE route number.
Operating Notes
For more on switch OSPF operation, refer to the "IP Routing" chapter in the latest Multicast and
Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(ospf)# show ip ospf statistics vlan 1
OSPF statistics for VLAN 1
OSPF Interface Status for 10.0.0.2
Tx
Tx
Tx
Tx
Tx
Hello Packet Count : 16
DD Packet Count : 2
LSR Packet Count : 1
LSU Packet Count : 5
LSA Packet Count : 2
Rx
Rx
Rx
Rx
Rx
Hello Packet Count : 16
DD Packet Count : 4
LSR Packet Count : 1
LSU Packet Count : 2
LSA Packet Count : 3
OSPF Errors: 26
display ospf cumulative Field Mappings.
Comware
ProVision Software
Hello
TX/RX Hello Packet Count
DB Description
n/a
Link-state Req
n/a
Link-State Update
n/a
Link-State Ack
n/a
LSA originated
n/a
LSA received
n/a
Routing Table fields
n/a
190 Display Commands
display ospf interface
Comware
Related ProVision
display ospf interface
show ip ospf interface
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPF interface information for all OSPF processes.
HP Switch(config)# display ospf interface
OSPF Process 1 with Router ID : 192.168.1.1
Area : 0.0.0.0
IP Address
Type
State
Cost Pri DR
BDR
--------------- --------- ------- ----- --- --------------- --------------192.168.1.1
PTP
P-2-P
1562 1
0.0.0.0
0.0.0.0
Area : 0.0.0.1
IP Address
Type
State
Cost Pri DR
BDR
--------------- --------- ------- ----- --- --------------- --------------172.16.0.1
BROADCAST DR
1562 1 172.16.0.1
0.0.0.0
Field Descriptions
Area: Area ID of the interface.
IP Address: Interface IP address.
Type: Interface network type (PTP, PTMP, Broadcast, or NBMA.
State: Interface state:
•
Down: No protocol traffic will be sent or received on the interface.
•
Waiting: The interface starts sending and receiving Hello packets and the router is trying to
determine the identity of the backup designated router for the network.
•
p-2-p: The interface will send Hello packets at the interval of HelloInterval, and try to establish
an adjacency with the neighbor.
•
DR: The router itself is the designated router on the attached network.
•
BDR: The router itself is the backup designated router on the attached network.
•
DROther: The interface is on a network on which another router is the designated router.
Cost: Interface cost.
Pri: Router priority.
DR: The DR on the interface’s network segment.
BDR: The BDR on the interface’s network segment.
Operating Notes
To enable OSPF operation in ProVision software, use the following command in the global
configuration context:
router ospf enable
For more on configuring OSPF, including additional OSPF configuration commands, see the
“Configuring OSPF” chapter in the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
display ospf interface
191
HP Switch(config)# show ip ospf interface
OSPF Interface Status
IP Address
Status
--------------- -------172.16.0.1
enabled
Area ID
State
Auth-type Cost Pri Passive
--------------- ------- --------- ----- --- ------backbone
DR
none
1562 1
no
OSPF Interface Field Mappings.
Comware
ProVision Software
Area
Area ID
IP Address
IP Address
n/a
Status
Type
n/a
State
State
n/a
Auth-Type
Cost
Cost
PRI
PRI
n/a
Passive
DR
n/a
BDR
n/a
192 Display Commands
display ospf lsdb
Comware
Related ProVision
display ospf lsdb
show ip ospf link-state
show ip ospf external-link-state
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPF link state database information.
HP Switch# display ospf lsdb
OSPF Process 1 with Router ID 7.7.7.7
Link State Database
Type
Router
Router
Network
Sum-Net
Type
Router
Router
Network
Sum-Net
Area: 0.0.0.0
AdvRouter
11.0.9.2
11.0.9.1
11.0.9.2
11.0.9.1
Area: 0.0.0.1
LinkState ID
AdvRouter
11.0.9.1
11.0.9.1
100.0.9.4
100.0.9.4
1.2.4.6
100.0.9.4
11.0.9.0
11.0.9.1
LinkState ID
11.0.9.2
11.0.9.1
11.0.9.2
1.2.4.0
Age
930
456
930
16
Len
n/a
n/a
n/a
n/a
Sequence
80000005
80000004
80000002
80000001
Metric
n/a
n/a
n/a
n/a
Age
9
10
5
16
Len
n/a
n/a
n/a
n/a
Sequence
80000003
80000004
80000002
80000001
Metric
n/a
n/a
n/a
n/a
AS External Database
Type
LinkState ID
AdvRouter
External
192.168.1.0
3.3.3.3
[bot-ospf-1-area-0.0.0.1]
Age
406
Len
n/a
Sequence
80000006
Metric
n/a
Field Descriptions
Area: LSDB information of the area
Type: LSA type
LinkState ID: Linkstate ID
AdvRouter: The router that advertised the LSA
Age: Age of the LSA
Len: Length of the LSA
Sequence: Sequence number of the LSA
Metric: Cost of the LSA
Operating Notes
For more on switch OSPF operation, refer to the "IP Routing" chapter in the latest Multicast and
Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# show ip ospf link-state
OSPF Link State Database for Area 0.0.0.0
LSA Type
Link State ID
Advertising
Router ID
Age
Sequence #
Checksum
display ospf lsdb
193
---------Router
Router
Network
Summary
Summary
Summary
Summary
AsbSummary
--------------10.0.8.32
10.0.8.33
10.3.2.37
10.3.16.0
10.3.16.0
10.3.17.0
10.3.17.0
10.0.8.36
--------------10.0.8.32
10.0.8.33
10.0.8.37
10.0.8.33
10.0.8.35
10.0.8.33
10.0.8.35
10.0.8.33
---65
1638
1695
1638
1316
1638
1316
1412
----------0x80000281
0x80000005
0x80000006
0x80000007
0x80000008
0x8000027b
0x80000008
0x80000002
---------0x0000a7b6
0x0000a7c8
0x00000443
0x0000c242
0x0000aa58
0x0000becf
0x0000a957
0x00002cba
Sequence #
----------0x8000027e
0x80000283
0x80000005
Checksum
---------0x0000d53c
0x0000de4f
0x00001465
OSPF Link State Database for Area 10.3.16.0
LSA Type
---------Router
Router
Network
Link State ID
--------------10.0.8.33
10.0.8.34
10.3.16.34
Advertising
Router ID
--------------10.0.8.33
10.0.8.34
10.0.8.34
Age
---1727
1420
1735
display ospf lsdb Field Mappings.
194
Comware
ProVision Software
Area
Area
Type
LSA Type
LinkState ID
LinkState ID
AdvRouter
Router ID
Age
Age
Len
n/a
Sequence
Sequence
Metric
n/a
Display Commands
display ospf peer
Comware
Related ProVision
display ospf peer
show ip ospf neighbor
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays information about OSPF neighbors.
HP Switch# display ospf peer
OSPF Process 1 with Router ID 1.1.1.1
Neighbor Brief Information
Area: 0.0.0.0
Router ID
1.1.1.2
Address
1.1.1.2
Pri Dead-Time
1
40
Interface
Vlan11
State
Full/DR
Field Descriptions
Area: Neighbor area.
Router ID: Neighbor router ID
Address: Neighbor interface address.
Pri: Neighboring router priority.
Dead-Time: Dead interval remained.
Interface: Interface connected to the neighbor.
State: Neighbor state: Down, Init, Attempt, 2-Way, Exstart, Exchange, DR/BDR state, Loading or
Full.
Operating Notes
For more on switch OSPF operation, refer to the "IP Routing" chapter in the latest Multicast and
Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip ospf neighbor
OSPF Neighbor Information
Router ID
Pri IP Address
NbIfState
--------------- --- -------------- --------10.0.8.34
1 10.3.18.34
DR
10.3.53.38
1 10.3.53.38
DR
State
--------FULL
FULL
Rxmt
QLen Events
----- -----0
6
0
6
Helper
Status
-----none
none
display ospf peer Field Mappings.
Comware
ProVision Software
Area
n/a
Router ID
Router ID
Address
IP Address
Pri
Pri
display ospf peer 195
196
Comware
ProVision Software
Dead-Time
Dead Timer Expires
Interface
n/a
State
NbIfState/State
Display Commands
display ospf routing
Comware
Related ProVision
display ospf routing
show ip ospf
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPF routing information for all OSPF processes.
HP Switch(config)# display ospf routing
OSPF Process 1 with Router ID 192.168.1.2
Routing Tables
Routing for Network
Destination
Cost
192.168.1.0/24 1562
172.16.0.0/16
1563
Type
Stub
Inter
NextHop
192.168.1.2
192.168.1.1
AdvRouter
192.168.1.2
192.168.1.1
Area
0.0.0.0
0.0.0.0
Total Nets: 2
Intra Area: 1
Inter Area: 1
ASE: 0
NSSA: 0
Field Descriptions
Destination: Destination network.
Cost: Cost to destination.
Type: Route type (intra-area, transit, stub, inter-area, type 1 external, type 2 external).
NextHop: Next hop address.
AdvRouter: Advertising router.
Area: Area ID.
Total Nets: Total networks.
Intra Area: Total intra-area routes.
Inter Area: Total inter-area routes.
ASE: Total ASE routes.
NSSA: Total NSSA routes.
Operating Notes
To enable OSPF operation in ProVision software, use the following command in the global
configuration context:
router ospf enable
For more on configuring OSPF, including additional OSPF configuration commands, see the
“Configuring OSPF” chapter in the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.08.
display ospf routing
197
display ospf vlink
Comware
Related ProVision
display ospf vlink
show ip ospf virtual-link
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPF virtual link information.
HP Switch# display ospf vlink
OSPF Process 1 with Router ID 3.3.3.3
Virtual Links
Virtual-link Neighbor-ID -> 2.2.2.2, Neighbor-State: Full
Interface: 10.1.2.1 (Vlan-interface11)
Cost: 1562 State: P-2-P Type: Virtual
Transit Area: 0.0.0.1
Timers: Hello 10 , Dead 40 , Retransmit 5 , Transmit Delay 1
Field Descriptions
Virtual-link Neighbor-ID: ID of the neighbor connected to the router via the virtual link.
Neighbor-State: Neighbor’s operating state (Down, Init, 2-Way , ExStart, Exchange, Loading Full).
Interface: Local interface’s IP address and name of the virtual link.
Cost: Interface route cost.
State: Interface state.
Type: Link type (virtual link).
Transit Area: Transit area ID.
Timers: Values of the hello, dead, poll (NBMA), retransmit, and interface transmission delay timers.
Operating Notes
To enable OSPF operation in ProVision software, use the following command in the global
configuration context:
router ospf enable
For more on configuring OSPF, including virtual links and other OSPF operation, see the
“Configuring OSPF” chapter in the latest Multicast and Routing Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip ospf virtual-link
OSPF Virtual Interface Status
Transit AreaID Neighbor Router Authentication Interface State
--------------- --------------- --------------- --------------0.0.0.1
2.2.2.2
none
P2P
198 Display Commands
ospf vlink Field Mappings.
Comware
ProVision Software
Virtual-link Neighbor ID
Neighbor Router
Neighbor-State
Interface State
Interface
n/a
Cost
n/a
State
n/a
Transit Area
Transit AreaID
Timers
n/a
n/a
Authentication
display ospf vlink 199
display ospfv3
Comware
Related ProVision
display ospfv3
show ipv6 ospf3
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays brief information about OSPFv3.
HP Switch# display ospfv3
Routing Process "OSPFv3 (1)" with ID 3.3.3.3
Graceful restart restarter disabled
Graceful restart helper enabled
Graceful restart helper strict-lsa-checking disabled
Graceful restart interval n/a
SPF schedule delay 5 secs, Hold time between SPFs 10 secs
Minimum LSA interval n/a, Minimum LSA arrival n/a
Number of external LSA 1. These external LSAs' checksum Sum
0x7741
Number of AS-Scoped Unknown LSA 0
Number of LSA originated 4
Number of LSA received 0
Number of areas in this router is 2
Area BACKBONE(0)
Number of interfaces in this area is 1
SPF algorithm executed 0 times
Number of LSA 0. These LSAs' checksum Sum 0x0000
Number of Unknown LSA 0
Area 0.0.0.1
Number of interfaces in this area is 1
SPF algorithm executed 9 times
Number of LSA 2. These LSAs' checksum Sum 0x1A56A
Number of Unknown LSA 0
Example of Related ProVision Software Command Output.
HP Switch# show ipv6 ospf3 general
OSPFv3 General Status
OSPFv3 protocol :enabled
Router ID :10.10.10.80
...
Nonstop forwarding : Enabled
Graceful Restart Interval : 500
Graceful Restart Helper Mode : Enabled
...
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
200 Display Commands
display ospfv3 area area-id peer interface interface-type interface number
Comware
Related ProVision
display ospfv3 area area-id peer interface interface-type No equivalent ProVision software command
interface number
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPFv3 neighbor information.
HP Switch# display ospfv3 area 0 peer Vlan-interface 1
OSPFv3 (Process 1)
OSPFv3 Area (0.0.0.0)
Neighbor ID
1.1.1.1
Pri
1
State
Full
Dead Time
00:00:35
Interface
Vlan1
Instance ID
0
Field Descriptions
Neighbor ID: Router ID of a neighbor
Pri: Priority of neighbor router
State: Neighbor state
Dead Time: Dead time remained
Interface: Interface connected to the neighbor
Instance ID: Instance ID:
Operating Notes
For more on switch OSPFv3 operation, refer to the "OSPFv3 Routing" chapter in the latest IPv6
Configuration Guide for your switch.
display ospfv3 area area-id peer interface interface-type interface number 201
display ospfv3 area area-id peer peer-router-id
Comware
Related ProVision
display ospfv3 area area-id peer peer-router-id
show ipv6 ospf3 neighbor <ip-addr> detail
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPFv3 neighbor information for the specified area.
HP Switch(config)# display ospfv3 area 0 peer 1.1.1.1
OSPFv3 Process (1)
Neighbor 1.1.1.1 is Full, interface address FE80::21B:3FFF:FEF7:DEC0
In the area 0.0.0.0 via interface Vlan-interface1
DR is 2.2.2.2 BDR is 1.1.1.1
Options is 0x000013 (-|R|-|-|E|V6)
Dead timer due in 00:00:35
Neighbor is up for 00:03:51
Database Summary List 0
Link State Request List 0
Link State Retransmission List 0
Graceful restart state: Normal
Field Descriptions
Neighbor: Neighbor ID.
Interface Address: Interface Address
In the area: The area address.
Vlan-interface: Vlan-interface <vid> belongs to area <area>.
DR/BDR: Router Id of the Designated Router and the Backup Designated Router.
Options: Displays the capabilities.
Dead timer: Indicates when the dead timer is due.
Neighbor up: Neighbor has been up for the indicated time.
Database Summary List: Number of LSAs sent in the DD packet.
Link State Request List: Number of LSAs in the link state request list.
Link State Retransmission List: Number of LSAs in the link state retransmission list.
Graceful restart state: Graceful restart status can be:
•
Normal: Normal status
•
Helper: The device is a Graceful Restart Helper of the neighbor.
Operating Notes
For more on switch OSPFv3 operation, refer to the "OSPFv3 Routing" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(ospf3)# show ipv6 ospf3 neighbor 15.1.0.1 detail
OSPFv3 Neighbor Information for neighbor 15.1.0.1
IPv6 Address
Router ID :
Interface :
Area
:
202 Display Commands
: fe80::55:1
15.1.0.1
vlan-55
0.0.0.1
State
: FULL
Designated Router
: 15.1.0.1
Backup Designated Router : 15.1.0.4
Priority
Options
Events
: 1
: 19
: 0
Retransmit Queue Length
Neighbor Uptime
Dead Timer Expires
: 0
: 1days
: 33 sec
display ospfv3 area area-id peer peer-id Field Mappings.
Comware
ProVision Software
Neighbor
Neighbor
Interface Address
IPv6 Address
In the area
Area ID
Vlan-interface
Interface
DR/BDR
Designated Router/Backup Designated Router
Options
Options
Dead timer
Dead Timer expires
Neighbor up
Neighbor Uptime
Database Summary List
n/a
Link State Request
n/a
Link State Retransmission List
Retransmit Queue Length
Graceful Restart
n/a
display ospfv3 area area-id peer peer-router-id 203
display ospfv3 area area-id peer verbose
Comware
Related ProVision
display ospfv3 area area-id peer verbose
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays detailed information about OSPFv3 neighbors for a specified area.
HP Switch(config)# display ospfv3 area 1 peer verbose
Neighbor 3.3.3.3 is Full, interface address FE80::221:F7FF:FE1B:EC80
In the area 0.0.0.1 via interface Vlan-interface2
DR is 3.3.3.3 BDR is 2.2.2.2
Options is 0x000013 (-|R|-|-|E|V6)
Dead timer due in 00:00:34
Neighbor is up for 00:01:44
Database Summary List 0
Link State Request List 0
Link State Retransmission List 0
Graceful restart state: Normal
Field Descriptions
Neighbor: Neighbor ID.
Interface Address: Interface Address
In the area: The area address.
Vlan-interface: Vlan-interface <vid> belongs to area <area>
DR/BDR: Router Id of the Designated Router and Backup Designated Router.
Options: Displays the capabilities.
Dead timer: Indicates when the dead timer is due.
Neighbor up: Neighbor has been up for the indicated time.
Database Summary List: Number of LSAs sent in the DD packet.
Link State Request List: Number of LSAs in the link state request list.
Link State Retransmission List: Number of LSAs in the link state retransmission list.
Graceful restart state: Graceful restart status can be:
•
Normal: Normal status
•
Helper: The device is a Graceful Restart Helper of the neighbor.
Operating Notes
For more on switch OSPFv3 operation, refer to the "OSPFv3 Routing" chapter in the latest IPv6
Configuration Guide for your switch.
204 Display Commands
display ospfv3 interface
Comware
Related ProVision
display ospfv3 interface
show ipv6 ospf3 interface
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPF interface information for all OSPF processes.
NOTE:
Only one process is supported, so the process number is always 1.
HP Switch(config)# display ospf3 interface
Vlan-interface4 is down, line protocol is up
Interface ID vlan-4
IPv6 Prefixes 1234::2/96
(Link-Local Address):
OSPFv3 Process (1), Area 0.0.0.4
Instance ID 0
Router ID: 0.0.0.40
Network Type: BROADCAST, Cost: 1
Transmit Delay is 1 sec, State: DR
Priority: 1
Designated Router (ID) 2001:db8:0:5::10:1/64
Interface Address: FE80::212:79FF:FE88:4D00
Backup Designated Router (ID): 2001:db8:0:5::10:2/64
Interface Address: FE80::218:71FF:FEC4:F00
Timer interval configured, Hello: 10 Dead: 40 Wait: 40 Retransmit: 5
Hello due in 00:00:09
Neighbor Count is 0
Adjacent neighbor count is 0
Field Descriptions
Interface ID: Interface ID
IPv6 Prefixes: IPv6 Prefixes
OSPF Process: OSPF Process
Area: Area ID of the interface.
Instance ID: Instance ID
Router ID: Router ID
Network Type: Network type of the interface (PTP, PTMP, Broadcast, or NBMA).
Cost: Cost value of the interface.
Transmit Delay: Transmission delay of the interface.
State: Interface state:
•
Down: No protocol traffic will be sent or received on the interface.
•
Waiting: In this state, the router is trying to determine the identity of the (Backup) Designated
Router for this network.
•
p-2-p: The interface is in point-to-point state and will skip the waiting period and DR/BDR
election.
•
DR: The router itself is the designated router on the attached network.
•
BDR: The router itself is the backup designated router on the attached network.
•
DROther: The interface is neither a Designated Router nor a backup Designated Router.
Priority: Router priority for the DR/BDR election.
Designated Router: The DR on the interface&rsquo;s network segment.
Backup Designated Router: The BDR on the interface&rsquo;s network segment.
display ospfv3 interface 205
Time Interval Configured: Time interval in seconds configured on the interface:
•
Hello—Hello interval.
•
Dead—Dead interval.
•
Wait—After this timer expires, the interface quits from the waiting state.
•
Retransmit—LSA retransmission interval.
Hello due in: Hello packet will be sent in the indicated number of seconds.
Neighbor Count: Number of neighbors on the interface.
Adjacent Neighbor Count: Number of adjacencies on the interface.
Operating Notes
To enable OSPF operation in ProVision software, enter the following commands in the global
configuration context:
ipv6 unicast-routing
router ospf3 enable
For more on configuring OSPFv3, including additional OSPFv3 configuration commands, see the
"OSPFv3 Routing" chapter in the latest IPv6 Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 ospf3 interface 75 detail
OSPFv3 configuration and statistics for VLAN 75
Interface
Area ID
Priority
Type
Hello Interval
Transit Delay
Events
Neighbors
:
:
:
:
:
:
:
:
vlan-75
0.0.0.3
1
BCAST
10
1
0
1
Status
State
Cost
Passive
Dead Interval
Retransmit Interval
Designated Router
Backup Designated Router
OSPF Interface Field Mappings.
Comware
ProVision Software
Interface ID
Interface
n/a
Status
IPv6 Prefixes
n/a
OSPF Process
n/a
Area
Area ID
Instance ID
n/a
Router ID
n/a
Network Type
Type
Cost
Cost
Transmit Delay
Transit Delay
State
State
Priority
Priority
Designated Router
Designated Router
206 Display Commands
:
:
:
:
:
:
:
:
Enabled
WAIT
1
Yes
40
5
15.1.1.2
15.1.4.4
Comware
ProVision Software
Backup Designated Router
Backup Desig. Rtr
n/a
Passive
Time Interval Configured
Retransmit Interval
Hello due in
n/a
Neighbor Count
Neighbors
Adjacent Neighbor Count
n/a
display ospfv3 interface 207
display ospfv3 lsdb
Comware
Related ProVision
display ospfv3 lsdb
show ipv6 ospf3 link-state
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPFv3 LSDB information. This command is available only in manager mode.
HP Switch# display ospfv3 lsdb
OSPFv3 Router with ID (2.2.2.2) (Process 1)
Link-LSA (Interface Vlan-interface1)
--------------------------------------------------------------------Link State ID
Origin Router
Age
SeqNum
CkSum Prefix
5.178.0.0
1.1.1.1
1082 0x8000000c 0x31c7
1
5.178.0.0
2.2.2.2
0896 0x8000000b 0xe23c
1
Link-LSA (Interface Vlan-interface2)
--------------------------------------------------------------------Link State ID
Origin Router
Age
SeqNum
CkSum Prefix
5.178.0.1
2.2.2.2
0896 0x8000000b 0x0f0d
1
5.178.0.1
3.3.3.3
0654 0x8000000b 0xcf90
1
Router-LSA (Area 0.0.0.0)
--------------------------------------------------------------------Link State ID
Origin Router
Age
SeqNum
CkSum
Link
0.0.0.0
1.1.1.1
0892
0x8000000e 0x8e0c
1
0.0.0.0
2.2.2.2
0376
0x8000000d 0x7b19
1
Network-LSA (Area 0.0.0.0)
--------------------------------------------------------------------Link State ID
Origin Router
Age
SeqNum
CkSum
5.178.0.0
1.1.1.1
0887
0x80000016 0xcc7f
Inter-Area-Prefix-LSA (Area 0.0.0.0)
--------------------------------------------------------------------Link State ID Origin Router
Age
SeqNum
CkSum
0.0.0.1
2.2.2.2
0886 0x8000000b 0x7962
Intra-Area-Prefix-LSA (Area 0.0.0.0)
--------------------------------------------------------------------Link State ID Origin Router
Age SeqNum
CkSum Prefix
Reference
0.0.0.2
1.1.1.1
0892 0x8000000b 0x05ee
1
Network-LSA
Router-LSA (Area 0.0.0.1)
--------------------------------------------------------------------Link State ID Origin Router
Age
SeqNum
CkSum
Link
0.0.0.0
2.2.2.2
0376 0x80000010 0xe7a3
1
0.0.0.0
3.3.3.3
0649 0x8000000c 0xc8c5
1
Network-LSA (Area 0.0.0.1)
--------------------------------------------------------------------Link State ID Origin Router
Age
SeqNum
CkSum
5.178.0.1
2.2.2.2
0371 0x80000018 0xf448
Inter-Area-Prefix-LSA (Area 0.0.0.1)
--------------------------------------------------------------------Link State ID Origin Router
Age
SeqNum
CkSum
0.0.0.1
2.2.2.2
0891 0x8000000b 0x6d6f
Intra-Area-Prefix-LSA (Area 0.0.0.1)
208 Display Commands
--------------------------------------------------------------------Link State ID Origin Router
Age SeqNum
CkSum Prefix Reference
0.0.0.2
2.2.2.2
0651 0x8000000b 0x37b2
1 Network-LSA
AS-external-LSA
--------------------------------------------------------------------Link State ID
Origin Router
Age SeqNum
CkSum
0.0.0.1
2.2.2.2
0375 0x8000000b 0x999a
0.0.0.2
2.2.2.2
0570 0x80000002 0x6ebc
Minimum Software Version: 15.10.
display ospfv3 lsdb 209
display ospfv3 lsdb statistics
Comware
Related ProVision
display ospfv3 lsdb statistics
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays LSA statistics in the OSPFv3 LSDB. This command is available only in manager mode.
HP Switch# display ospfv3 lsdb statistics
OSPFv3 Router with ID (2.2.2.2) (Process 1)
LSA Statistics
--------------------------------------------------------------------Area ID
Router Network IntePre InteRou IntraPre Link Grace ASE
0.0.0.0
5
5
5
5
5
0.0.0.1
5
5
5
5
5
Total
10
10
10
10
10
5
0
5
Minimum Software Version: 15.10.
210
Display Commands
display ospfv3 peer
Comware
Related ProVision
display ospfv3 peer
show ipv6 ospf3 neighbor
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPFv3 neighbor information.
HP Switch(vlan-2)# display ospfv3 peer
OSPFv3 Area ID 0.0.0.1 (Process 1)
Neighbor ID
Pri
State
Dead Time
Interface Instance ID
-------------------------------------------------------------------------120.85.228.88
1
FULL
00:00:33
Vlan2
0
Field Descriptions
Neighbor ID: Router ID of a neighbor.
Pri: Priority of neighbor router for DR/BDR election.
State: Neighbor state.
Dead time: Dead time remaining
Interface: Interface connected to the neighbor.
Instance ID: Instance ID
Operating Notes
For more on switch OSPFv3 operation, refer to the "OSPFv3 Routing" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(ospf3)# show ipv6 ospf3 neighbor
OSPFv3 Neighbor Information
Interface
--------Vlan-55
Vlan-75
tunnel-3
Router ID
--------------15.1.0.1
15.1.1.2
4.3.2.1
Pri
----1
1
1
State
---------Full
Full
Full
Rxmt QLen
---------0
0
0
Events
---------0
0
0
display ospfv3 peer Field Mappings.
Comware
ProVision Software
Neighbor ID
Router ID
Interface
Interface
n/a
Router ID
Pri
Pri
State
State
Dead time
n/a
Instance ID
n/a
display ospfv3 peer
211
212
Comware
ProVision Software
n/a
Rxmt QLen
n/a
Events
Display Commands
display ospfv3 peer peer-router-id
Comware
Related ProVision
display ospfv3 peer peer-router-id
show ipv6 ospf3 neighbor <router-id> detail
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the router ID of the specified neighbor.
HP Switch# display ospfv3 peer 2.2.2.2
Neighbor 2.2.2.2 is Full, interface address FE80::223:89FF:FECB:6FDC
In the area 0.0.0.0 via interface Vlan-interface1
DR is 2.2.2.2 BDR is 1.1.1.1
Options is 0x000013 (-|R|-|-|E|V6)
Dead timer due in 00:00:35
Neighbor is up for 00:04:35
Database Summary List 0
Link State Request List 0
Link State Retransmission List 0
Graceful restart state: Normal
Field Descriptions
Neighbor: Neighbor ID.
Interface Address: Interface Address
Vlan-interface: Vlan-interface <vid> belongs to area <area>.
DR/BDR: Router Id of the Designated Router and the Backup Designated Router.
Options: Displays the capabilities.
Dead timer: Indicates when the dead timer is due.
Neighbor up: Neighbor has been up for the indicated time.
Database Summary List: Number of LSAs sent in the DD packet.
Link State Request List: Number of LSAs in the link state request list.
Link State Retransmission List: Number of LSAs in the link state retransmission list.
Graceful restart state: Graceful restart status can be:
•
Normal: Normal status
•
Helper: The device is a Graceful Restart Helper of the neighbor.
Operating Notes
For more on switch OSPFv3 operation, refer to the "OSPFv3 Routing" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(ospf3)# show ipv6 ospf3 neighbor 15.1.0.1 detail
OSPFv3 Neighbor Information for neighbor 15.1.0.1
IPv6 Address
Router ID :
Interface :
Area
:
Priority
:
: fe80::55:1
15.1.0.1
vlan-55
0.0.0.1
1
State
Designated Router
Backup Designated Router
Retransmit Queue Length
:
:
:
:
FULL
15.1.0.1
15.1.0.4
0
display ospfv3 peer peer-router-id
213
Options
Events
: 19
: 0
Neighbor Uptime
Dead Timer Expires
: 1days
: 33 sec
display ospfv3 peer verbose Field Mappings.
214
Comware
ProVision Software
Neighbor
Neighbor
Interface Address
IPv6 Address
Vlan-interface
Interface
DR/BDR
Designated Router/Backup Designated Router
Options
Options
Dead timer
Dead Timer expires
Neighbor up
Neighbor Uptime
Database Summary List
n/a
Link State Request
n/a
Link State Retransmission List
Retransmit Queue Length
Graceful Restart
n/a
Display Commands
display ospfv3 peer statistics
Comware
Related ProVision
display ospfv3 peer statistics
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays information about all OSPFv3 neighbors on the router, that is, number of neighbors in
different states.
HP Switch# display ospfv3 peer statistics
OSPFv3 Router with ID (2.2.2.2) (Process 1)
Neighbor Statistics
--------------------------------------------------------------------Area ID
Down Attempt Init 2-Way ExStart Exchange Loading Full
0.0.0.0
0
0
0
0
0
0
0
1
0.0.0.1
0
0
0
0
0
0
0
1
Total
0
0
0
0
0
0
0
2
Minimum Software Version: 15.10.
display ospfv3 peer statistics
215
display ospfv3 peer verbose
Comware
Related ProVision
display ospfv3 peer verbose
show ipv6 ospf3 neighbor detail
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays detailed information about OSPFv3 neighbors.
HP Switch# display ospfv3 peer verbose
Neighbor 2.2.2.2 is Full, interface address FE80::223:89FF:FECB:6FDC
In the area 0.0.0.0 via interface Vlan-interface1
DR is 2.2.2.2 BDR is 1.1.1.1
Options is 0x000013 (-|R|-|-|E|V6)
Dead timer due in 00:00:30
Neighbor is up for 00:00:20
Database Summary List 0
Link State Request List 0
Link State Retransmission List 0
Graceful restart state: Normal
Field Descriptions
Neighbor: Neighbor ID.
Interface Address: Interface Address
Vlan-interface: Vlan-interface <vid> belongs to area <area>.
DR/BDR: Router-Id of the Designated Router and the Backup Designated Router.
Options: Displays the capabilities.
Dead timer: Indicates when the dead timer is due.
Neighbor up: Neighbor has been up for the indicated time.
Database Summary List: Number of LSAs sent in the DD packet.
Link State Request List: Number of LSAs in the link state request list.
Link State Retransmission List: Number of LSAs in the link state retransmission list.
Graceful restart state: Graceful restart status can be:
•
Normal: Normal status
•
Helper: The device is a Graceful Restart Helper of the neighbor.
Operating Notes
For more on switch OSPFv3 operation, refer to the "OSPFv3 Routing" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(ospf3)# show ipv6 ospf3 neighbor 15.1.0.1 detail
OSPFv3 Neighbor Information for neighbor 15.1.0.1
IPv6 Address
Router ID :
Interface :
Area
:
Priority
:
216
Display Commands
: fe80::55:1
15.1.0.1
vlan-55
0.0.0.1
1
State
Designated Router
Backup Designated Router
Retransmit Queue Length
:
:
:
:
FULL
15.1.0.1
15.1.0.4
0
Options
Events
: 19
: 0
Neighbor Uptime
Dead Timer Expires
: 1days
: 33 sec
display ospfv3 peer verbose Field Mappings.
Comware
ProVision Software
Neighbor
Neighbor
Interface Address
IPv6 Address
Vlan-interface
Interface
DR/BDR
Designated Router/Backup Designated Router
Options
Options
Dead timer
Dead Timer expires
Neighbor up
Neighbor Uptime
Database Summary List
n/a
Link State Request
n/a
Link State Retransmission List
Retransmit Queue Length
Graceful Restart
n/a
display ospfv3 peer verbose
217
display ospfv3 statistic
Comware
Related ProVision
display ospfv3 statistic
show ipv6 ospf3 statistics
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays outbound/inbound OSPFv3 packet statistics on associated interface( s).
HP Switch(vlan-2)# display ospfv3 statistics
OSPFv3 Statistics
Interface 2 Instance 0
Type
Input
Output
Hello
6
10
DB Description
2
5
Ls Req
1
1
Ls Upd
2
3
Ls Ack
2
2
Discarded
32
1
Field Descriptions
Interface: Interface name.
Instance: Instance number.
Type: Type of packet.
Input: Number of packets received by the interface.
Output: Number of packets sent by the interface.
Hello: Hello packet.
DB Description: Database description packet.
Ls Req: Link state request packet
Ls Upd: Link state update packet
Ls Ack: Link state acknowledgement packet
Discarded: Number of discarded packets.
Operating Notes
For more on switch OSPFv3 operation, refer to the "OSPFv3 Routing" chapter in the latest IPv6
Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
Per-VLAN OSPF Statistics
218
Field
Content
OSPF statistics for VLAN
<vlan-id>
OSPF statistics displayed for the specified VLAN number
OSPF Interface Status for
<ip-address>
IP address of a subnet on the VLAN
Tx/Rx Hello Packet Count
Number of OSPF hello packets sent/received on each subnet interface
Tx/Rx DD Packet Count
Number of link-state database description packets sent/ received on each subnet
interface
Display Commands
Per-VLAN OSPF Statistics
Field
Content
Tx/Rx LSR Packet Count
Number of link-state request packets sent/received on each subnet interface
Tx/Rx LSU Packet Count
Number of link-state update packets sent/received on each subnet interface
Tx/Rx LSA Packet Count
Number of link-state acknowledgement packets sent/ received on each subnet
interface
OSPF errors
Number of errors detected on the VLAN subnet during OSPF packet exchange
HP Switch# show ipv6 ospf3 statistics vlan 55
OSPFv3 statistics for VLAN 55
Tx Hello Packets
: 26005
Tx DD Packets
: 3
Tx LSR Packets
: 1
Tx LSU Packets
: 1436
Tx LSA Packets
: 615
OSPFv3 Errors
Rx
Rx
Rx
Rx
Rx
Hello Packets
DD Packets
LSR Packets
LSU Packets
LSA Packets
:
:
:
:
:
26005
3
1
1046
1444
: 0
display ospfv3 statistic Field Mappings.
Comware
ProVision Software
Interface
OSPF statistics for
Instance
n/a
Type
n/a
Input
n/a
Output
n/a
Hello
Tx/Rx Hello Packets
DB Description
Tx/Rx DD Packets
Ls Req
Tx/Rx LSR Packets
Ls Upd
Tx/Rx LSU Packets
Ls Ack
Tx/Rx LSA Packets
Discarded
Total Errors
display ospfv3 statistic
219
display ospfv3 vlink
Comware
Related ProVision
display ospfv3 vlink
show ipv6 ospf3 virtual-link ?
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays OSPFv3 virtual link information.
HP Switch# display ospfv3 vlink
Virtual Link VLINK1 to router 1.1.1.1 is up
Transit area :0.0.0.1 via interface Vlan-interface11, instance ID: 0
Local address: 2000:1::1
Remote address: 2001:1:1::1
Transmit Delay is 1 sec, State: P-To-P,
Timer intervals configured, Hello: 10, Dead: 40, Wait: 40, Retransmit: 5
Hello due in 00:00:02
Adjacency state :Full
Field Descriptions
Virtual Link: The virtual link name and destination router ID.
Transit area: The VLAN interface ID and transit area.
Instance ID: Instance identity.
Local address: The local router IPv6 address.
Remote address: The remote router IPv6 address.
Transmit Delay: The transmit delay for sending LSAs.
State: The state of the interface, such as P-To-P.
Timer intervals: The configured timer intervals for Hello, Dead, Wait, and Retransmit.
Hello due in: The interval until the next Hello packet is sent.
Adjacency state: The current virtual neighbor adjacency state
Operating Notes
To configure OSPFv3 operation in ProVision software, see the “OSPFv3 Routing” chapter in the
latest IPv6 Configuration Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ipv6 ospf3 virtual-link
OSPFv3 Virtual Interface Status
Transit AreaID
Neighbor Router Interface State
--------------- --------------- --------------0.0.0.1
1.1.1.1
P2P
220 Display Commands
ospfv3 vlink Field Mappings.
Comware
ProVision Software
Virtual Link
Neighbor Router
Transit area
Transit AreaID
Local address
n/a
Remote address
n/a
Transmit Delay
n/a
State
Interface State
Timer intervals
n/a
Hello due
n/a
Adjacency state
n/a
display ospfv3 vlink 221
display pim bsr-info
Comware
Related ProVision
display pim bsr-info
show ip pim bsr
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the BSR information in the PIM domain and the locally configured C-RP information in
effect.
HP Switch# display pim bsr-info
Elected BSR Address : 10.10.10.11
Priority : 0
Hash mask length : 30
State: n/a
Scope: n/a
Uptime : 00:08:00
Next BSR message scheduled at : 01:20:00
Candidate BSR Address : 10.10.10.10
Priority : 0
Hash mask length : 30
State: n/a
Scope: n/a
Candidate RP: 10.10.10.10(Vlan-interface10)
Priority : 192
HoldTime : 192
Advertisement Interval : 192
Next advertisement scheduled at: n/a
Candidate RP: 10.10.10.10(Vlan-interface20)
Priority : 192
HoldTime : 192
Advertisement Interval : 192
Next advertisement scheduled at: n/a
Candidate RP: 10.10.10.10(Vlan-interface30)
Priority : 192
HoldTime : 192
Advertisement Interval : 192
Next advertisement scheduled at: n/a
Field Descriptions
VPN-Instance: public net: Public network.
Elected BSR Address: Address of the elected BSR.
Candidate BSR Address: Address of the candidate BSR.
Priority: BSR priority.
Hash mask length: Hash mask length
State: BSR state.
Scope: Scope of the BSR.
Uptime: Length of time for which this BSR has been up, in hh:mm:ss.
Next BSR message scheduled at: Length of time in which the BSR will expire, in hh:mm:ss.
Candidate RP: Address of the C-RP.
Priority: Priority of the C-RP.
HoldTime: Timeout time of the C-RP.
Advertisement Interval: Interval at which the C-RP sends advertisement messages.
222 Display Commands
Next advertisement scheduled at: Length of time in which the C-RP will send the next advertisement
message, in hh:mm:ss.
Operating Notes
For more information on PIM, see the "PIM-SM (Sparse Mode)" or the "PIMDM (Dense Mode)
chapters in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
display pim bsr-info Field Mappings.
Comware
ProVision Software
VPN-Instance public net
n/a
Elected BSR Address
E-BSR Address
Candidate BSR Address
C-BSR Address
Priority
E-BSR Priority
Hash mask length
E-BSR Hash Mask Length
State
n/a
Scope
n/a
Uptime
E-BSR Uptime
Next BSR messaged scheduled at
Next Bootstrap Message
Candidate RP
C-RP Address
Priority
C-RP Priority
HoldTime
C-RP Hold Time
Advertisement Interval
C-RP Advertise Period
Next advertisement scheduled at
n/a
display pim bsr-info 223
display pim control-message counters
Comware
Related ProVision
display pim control-message counters
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays statistics information of PIM control messages.
HP Switch# display pim control-message counters
VPN-Instance: n/a
PIM global control-message counters:
Received
Sent
Register
0
0
Register-Stop
0
0
Probe
n/a
n/a
Invalid
0
0
n/a
PIM control-message counters for interface: Vlan-interface10
Received
Sent
Invalid
Assert
0
0
0
Graft
0
0
0
Graft-Ack
0
0
0
Hello
0
0
0
Join/Prune
0
0
0
State-Refresh
0
0
0
BSR
0
0
0
C-RP
0
0
0
PIM control-message counters for interface: Vlan-interface30
Received
Sent
Invalid
Assert
0
0
0
Graft
0
0
0
Graft-Ack
0
0
0
Hello
0
0
0
Join/Prune
0
0
0
State-Refresh
0
0
0
BSR
0
0
0
C-RP
0
0
0
Minimum Software Version: 15.10.
224 Display Commands
display pim grafts
Comware
Related ProVision
display pim grafts
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays information about unacknowledged PIM-DM graft messages.
HP Switch# display pim grafts
vlan 1
name "DEFAULT_VLAN"
no untagged 1-2,48
untagged 3-47
ip address dhcp-bootp
exit
vlan 10
name "VLAN10"
untagged 1,48
ip address 10.10.10.3 255.255.255.0
ip igmp
exit
vlan 30
name "VLAN30"
untagged 2
ip address 30.30.30.2 255.255.255.0
ip igmp
ip rip 30.30.30.2
ip pim-sparse
ip-addr any
exit
exit
Minimum Software Version: 15.10.
display pim grafts 225
display pim interface
Comware
Related ProVision
display pim interface <interface>
show ip pim interface
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the PIM information on the specified interface or all interfaces.
HP Switch# display pim interface
VPN-Instance: n/a
Interface
NbrCnt HelloInt
Vlan10
n/a
30
Vlan20
n/a
30
Vlan30
n/a
30
DR-Pri
1
1
1
DR-Address
10.10.10.11
20.20.20.20
30.30.30.30
Field Descriptions
VPN-Instance: public net: Public network.
Interface: Interface name.
NbrCnt: Number of PIM neighbors.
HelloInt: Hello interval.
DR-Pri: Priority for DR election.
DR-Address: DR IP address, where "local" indicates a local address
Operating Notes
For more information on PIM, see the "PIM-SM (Sparse Mode)" or the "PIMDM (Dense Mode)
chapters in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip pim interface
PIM Interfaces
VLAN
---1
2
IP Address
--------------10.1.10.1
10.2.10.1
Mode
-----------sparse
sparse
display pim interface Field Mappings.
Comware
ProVision Software
VPN-Instance public net
n/a
Interface
VLAN
NbrCnt
n/a
HelloInt
n/a
DR-Pri
n/a
DR-Address
IP Address
n/a
Mode
226 Display Commands
display pim interface verbose
Comware
Related ProVision
display pim interface verbose
show ip pim interface <int>
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays detailed PIM information.
HP Switch# display pim interface verbose
Interface : Vlan-interface10, 10.10.10.10
PIM version : n/a
PIM mode : 2
PIM DR : 10.10.10.10
PIM DR Priority (configured) : 1
PIM neighbor count: n/a
PIM hello interval : 30
PIM LAN delay (negotiated): n/a
PIM LAN delay (configured) : 500
PIM override interval (negotiated): n/a
PIM override interval (configured) : 2500
PIM neighbor tracking (negotiated): n/a
PIM neighbor tracking (configured): n/a
PIM generation ID : 2
PIM require generation ID: n/a
PIM hello hold interval : 105
PIM assert hold interval: n/a
PIM triggered hello delay : 5
PIM J/P interval : 60
PIM J/P hold interval: n/a
PIM state-refresh processing : 1
PIM state-refresh interval : 0
PIM state-refresh rate limit: n/a
PIM state-refresh TTL : 0
PIM graft retry interval : 3
Number of routers on network not using DR priority: n/a
Number of routers on network not using LAN delay: n/a
Number of routers on network not using neighbor tracking: n/a
Field Descriptions
VPN-Instance Public net: Public network.
Interface: Interface name and its IP address.
PIM version: Running PIM version.
PIM mode: PIM mode, dense or sparse.
PIM DR: DR IP address.
PIM DR Priority (configured): Configured priority for DR election.
PIM neighbor count: Total number of PIM neighbors.
PIM hello interval: Hello interval.
PIM LAN delay (negotiated): Negotiated prune message delay.
PIM LAN delay (configured): Configured prune message delay.
PIM override interval (negotiated): Negotiated prune override interval.
PIM override interval (configured): Configured prune override interval.
PIM neighbor tracking (negotiated): Negotiated neighbor tracking status (enabled/disabled).
display pim interface verbose 227
PIM neighbor tracking (configured): Configured neighbor tracking status (enabled/disabled).
PIM generation ID: Generation_ID value.
PIM require generation ID: Rejection of Hello messages without Generation_ID (enabled/disabled).
PIM hello hold interval: PIM neighbor timeout time.
PIM assert hold interval: Assert timeout time.
PIM triggered hello delay: Maximum delay of sending hello messages.
PIM J/P interval: Join/prune interval.
PIM J/P hold interval: Join/prune timeout time.
PIM BSR domain border: Status of PIM domain border configuration (enabled/ disabled).
Number of routers on network not using DR priority: Number of routers not using the DR priority
field on the subnet where the interface resides.
Number of routers on network not using LAN delay: Number of routers not using the LAN delay
field on the subnet where the interface resides.
Number of routers on network not using neighbor tracking: Number of routers not using neighbor
tracking on the subnet where the interface resides.
Operating Notes
For more information on PIM, see the "PIM-SM (Sparse Mode)" or the "PIMDM (Dense Mode)
chapters in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip pim interface 1
PIM Interface
VLAN
: 1
IP Address : 10.1.10.1
Mode
: sparse
Designated Router : 10.1.10.1
Hello Interval (sec) : 30
Hello Delay (sec)
: 5
Override Interval (msec) : 2500
Propagation Delay (msec) : 500
Neighbour Timeout
: 180
Lan Prune Delay
: Yes
Lan Delay Enabled
: No
DR Priority
: 1
display pim interface Field Mappings.
Comware
ProVision Software
VPN-Instance public net
n/a
Interface
VLAN
PIM Version
n/a
PIM mode
Mode
PIM DR
Designated Router
PIM DR Priority (configured)
DR Priority
PIM neighbor count
n/a
PIM hello interval
Hello Interval (sec)
PIM LAN delay (negotiated)
n/a
PIM LAN delay (configured)
Hello Delay
228 Display Commands
Comware
ProVision Software
PIM override interval (negotiated)
n/a
PIM override interval (configured)
Override Interval (msec0
PIM neighbor tracking (negotiated)
n/a
PIM neighbor tracking (configured)
n/a
PIM generation ID
n/a
PIM require generation ID
n/a
PIM hello hold interval
Hello Delay (sec)
PIM assert hold interval
n/a
PIM triggered hello delay
n/a
PIM J/P interval
n/a
PIM J/P hold interval
n/a
PIM state-refresh processing
n/a
PIM state-refresh interval
n/a
PIM state-refresh rate-limit
n/a
PIM state-refresh TTL
n/a
PIM graft retry interval
n/a
Number of routers on network not using DR priority
n/a
Number of routers on network not using LAN delay
n/a
Number of routers on network not using neighbor tracking n/a
display pim interface verbose 229
display pim join-prune
Comware
Related ProVision
display pim join-prune
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
HP Switch# display pim join-prune mode sm
VPN-Instance: public net
Expiry Time: 51 sec
Upstream nbr: 10.10.10.1 (Vlan-Interface10)
1 (*, G) join(s), 1 (S, G) join(s), 0 (S, G, rpt) prune(s)
------------------------------------------------------------Total (*, G) join(s): 1, (S, G) join(s): 1, (S, G, rpt) prune(s): 0
|...+....1....+....2....+....3....+....4....+....5....+....6.
...+....7....+....8
Minimum Software Version: 15.10.
230 Display Commands
display pim neighbor
Comware
Related ProVision
display pim neighbor
show ip pim neighbor
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays information about PIM neighbors.
HP Switch# display pim neighbor
VPN-Instance: n/a
Total Number of Neighbors = n/a
Neighbor
Interface Uptime
Expires Dr-Priority Mode
10.1.1.2
Vlan100 02:50:49 00:01:31 n/a
n/a
20.1.1.2
Vlan101 02:49:39 00:01:42 n/a
n/a
Field Descriptions
VPN-Instance: public net: Public network
Total Number of Neighbors: Total number of PIM neighbors
Neighbor: IP address of the PIM neighbor
Interface: Interface connecting the PIM neighbor
Uptime: Length of time for which the PIM neighbor has been up, in hh:mm:ss
Expires/Expiry time: Remaining time of the PIM neighbor, in hh:mm:ss; "never" means that the
PIM neighbor is always up and reachable.
Dr-Priority/DR Priority: Priority of the PIM neighbor
Mode: Mode of the PIM neighbor. The value "B" means the BIDIR-PIM mode. If nothing is displayed,
it means the non-BIDIR-PIM mode.
Operating Notes
For more information on PIM, see the "PIM-SM (Sparse Mode)" or the "PIMDM (Dense Mode)
chapters in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip pim neighbor
PIM Neighbors
IP Address
--------------10.10.10.2
10.20.10.1
VLAN
---100
200
Up Time (sec)
Expire Time (sec) DR Priority
---------------- ---------------- ---------348
90
1
410
97
1
display pim neighbor Field Mappings.
Comware
ProVision Software
VPN-Instance public net
n/a
Total Number of Neighbors
n/a
Neighbor
IP Address
Interface
VLAN
Uptime
UP Time (sec)
display pim neighbor
231
Comware
ProVision Software
Expires/Expiry time
Expire Time (sec)
Dr-Priority/DR Priority
DR Priority
Mode
n/a
232 Display Commands
display pim neighbor <ip> verbose
Comware
Related ProVision
display pim neighbor <ip> verbose
show ip pim neighbor
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays information about PIM neighbors.
HP Switch# display pim neighbor 11.110.0.20 verbose
VPN-Instance: n/a
Neighbor: 11.110.0.20
Interface: Vlan-interface100
Uptime: 00:00:10
Expiry time: 00:00:30
DR Priority: n/a
Generation ID: n/a
Holdtime: n/a
LAN delay: n/a
Override interval: n/a
State refresh interval: n/a
Neighbor tracking: n/a
Bidirectional PIM: n/a
Field Descriptions
VPN-Instance: public net: Public network
Total Number of Neighbors: Total number of PIM neighbors
Neighbor: IP address of the PIM neighbor
Interface: Interface connecting the PIM neighbor
Uptime: Length of time for which the PIM neighbor has been up, in hh:mm:ss
Expires/Expiry time: Remaining time of the PIM neighbor, in hh:mm:ss; "never" means that the
PIM neighbor is always up and reachable.
Dr-Priority/DR Priority: Priority of the PIM neighbor
Mode: Mode of the PIM neighbor. The value "B" means the BIDIR-PIM mode. If nothing is displayed,
it means the non-BIDIR-PIM mode.
Generation ID: Generation ID of the PIM neighbor (a random value indicating a status change of
the PIM neighbor)
Holdtime: Holdtime of the PIM neighbor; "forever" means that the PIM neighbor is always up and
reachable
LAN delay: Prune message delay
Override interval: Prune override interval
State refresh interval: Interval for sending state refresh messages/ Displayed only when the PIM
neighbor works in PIM-DM mode and the state refresh capability is enabled.
Neighbor tracking: Neighbor tracking status (enabled/disabled)
Bidirectional PIM: BIDIR-PIM status (enabled/disabled)
Operating Notes
For more information on PIM, see the "PIM-SM (Sparse Mode)" or the "PIMDM (Dense Mode)
chapters in the latest Multicast and Routing Guide for your switch.
Example of Related ProVision Software Command Output.
display pim neighbor <ip> verbose 233
HP Switch(config)# show ip pim neighbor
PIM Neighbors
IP Address
--------------10.10.10.2
10.20.10.1
VLAN
---100
200
Up Time (sec)
Expire Time (sec) DR Priority
---------------- ---------------- ---------348
90
1
410
97
1
display pim neighbor Field Mappings.
Comware
ProVision Software
Expires/Expiry time
Expire Time (sec)
Dr-Priority/DR Priority
DR Priority
Mode
n/a
Generation ID
n/a
Holdtime
n/a
LAN delay
n/a
Override interval
n/a
State refresh interval
n/a
Neighbor tracking
n/a
Bidirectional PIM
n/a
234 Display Commands
display pim routing-table
Comware
Related ProVision
display pim routing-table
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the contents of the PIM multicast routing table, which includes SPT and RPF information.
HP Switch# display pim routing-table
VPN-Instance: public net
Total 0 (*, G) entry; 1 (S, G) entry
(172.168.0.12, 227.0.0.1)
Protocol: pim-sm, Flag: LOC
UpTime: 02:54:43
Upstream interface: Vlan-interface20
Upstream neighbor: NULL
RPF prime neighbor: NULL
Downstream interface(s) information:
Total number of downstreams: 1
1: Vlan-interface10
Protocol: pim-sm, UpTime: 02:54:43, Expires: 00:02:47
Minimum Software Version: 15.10.
display pim routing-table 235
display pim rp-info
Comware
Related ProVision
display pim rp-info
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays information about pim RP.
HP Switch# display pim rp-info
VPN-Instance: public net
PIM-SM BSR RP information:
Group/MaskLen: 224.0.0.0/4
RP: 10.10.10.11
Priority: n/a
HoldTime: 150
Uptime: n/a
Expires: 00:01:00
Minimum Software Version: 15.10.
236 Display Commands
display poe device
Comware
Related ProVision
display poe device
show power-over-ethernet brief
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the mapping between ID, module, and slot of the power sourcing equipment (PSE).
HP Switch# display poe device
PSE ID SlotNo SubSNo PortNum MaxPower(W)
A
1
n/a
24
370
State
off
Model
J9310A
Example of Related ProVision Software Command Output.
HP Switch# show power-over-ethernet brief
Status and Counters - Port Power Status
System Power Status : No redundancy
PoE Power Status : No redundancy
Available: 300 W Used: 0 W Remaining: 300 W
Module A Power
Available: 300 W Used: 5 W Remaining: 295 W
PoE
| Power Power
Alloc Alloc Actual
Port
| Enable Priority By
Power Power
------ + ------ -------- ----- ----- -----A1
| Yes
low
usage 17 W 5.0 W
A2
| Yes
low
usage 17 W 0.0 W
A3
| Yes
low
usage 17 W 0.0 W
A4
| Yes
low
usage 17 W 0.0 W
A5
| Yes
low
usage 17 W 0.0 W
A6
| Yes
low
usage 17 W 0.0 W
Configured Detection
Type
Status
----------- ----------Phone1
Delivering
Searching
Searching
Searching
Searching
Searching
Power
Class
----1
0
0
0
0
0
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display poe device 237
display poe interface
Comware
Related ProVision
display poe interface
show power-over-ethernet brief
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the PoE status of a specific port on the switch.
HP Switch# display poe interface
Interface
Enable
Priority
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
enable
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
low
CurPower
(W)
IEEE
Class
Detection
Status
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
off
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
enabled
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
Operating
Status
--- 24 port(s) on, 0.0 (W) consumed, 0.0 (W) remaining ---
Example of Related ProVision Software Command Output.
HP Switch# show power-over-ethernet brief
Status and Counters - Port Power Status
System Power Status : No redundancy
PoE Power Status : No redundancy
Available: 300 W Used: 0 W Remaining: 300 W
Module A Power
Available: 300 W Used: 5 W Remaining: 295 W
PoE
| Power Power
Alloc Alloc Actual
Port
| Enable Priority By
Power Power
------ + ------ -------- ----- ----- -----A1
| Yes
low
usage 17 W 5.0 W
A2
| Yes
low
usage 17 W 0.0 W
A3
| Yes
low
usage 17 W 0.0 W
A4
| Yes
low
usage 17 W 0.0 W
A5
| Yes
low
usage 17 W 0.0 W
A6
| Yes
low
usage 17 W 0.0 W
238 Display Commands
Configured
Type
----------Phone1
Detection
Status
----------Delivering
Searching
Searching
Searching
Searching
Searching
Power
Class
----1
0
0
0
0
0
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display poe interface 239
display poe interface power
Comware
Related ProVision
display poe interface power
show power-over-ethernet brief
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the PoE power information of the specified port on the switch. If you enter the command
without an argument, the PoE power information about all PoE-capable ports on the switch is
displayed.
HP Switch# display poe interface power
Interface
CurPower PeakPower
MaxPower
(W)
(W)
(W)
1
0.0
0.0
15.4
2
0.0
0.0
15.4
3
0.0
0.0
15.4
4
0.0
0.0
15.4
5
0.0
0.0
15.4
6
0.0
0.0
15.4
7
0.0
0.0
15.4
8
0.0
0.0
15.4
9
0.0
0.0
15.4
10
0.0
0.0
15.4
11
0.0
0.0
15.4
12
0.0
0.0
15.4
13
0.0
0.0
15.4
14
0.0
0.0
15.4
15
0.0
0.0
15.4
16
0.0
0.0
15.4
17
0.0
0.0
15.4
18
0.0
0.0
15.4
19
0.0
0.0
15.4
20
0.0
0.0
15.4
21
0.0
0.0
15.4
22
0.0
0.0
15.4
23
0.0
0.0
15.4
24
0.0
0.0
15.4
PD Description
--- 0 port(s) on, 0.0 (W) consumed, 0.0 (W) remaining ---
Example of Related ProVision Software Command Output.
HP Switch# show power-over-ethernet brief
Status and Counters - Port Power Status
System Power Status : No redundancy
PoE Power Status : No redundancy
Available: 300 W Used: 0 W Remaining: 300 W
Module A Power
Available: 300 W Used: 5 W Remaining: 295 W
PoE
| Power Power
Alloc Alloc Actual
Port
| Enable Priority By
Power Power
------ + ------ -------- ----- ----- -----A1
| Yes
low
usage 17 W 5.0 W
A2
| Yes
low
usage 17 W 0.0 W
A3
| Yes
low
usage 17 W 0.0 W
A4
| Yes
low
usage 17 W 0.0 W
A5
| Yes
low
usage 17 W 0.0 W
A6
| Yes
low
usage 17 W 0.0 W
240 Display Commands
Configured
Type
----------Phone1
Detection
Status
----------Delivering
Searching
Searching
Searching
Searching
Searching
Power
Class
----1
0
0
0
0
0
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display poe interface power
241
display poe power-usage
Comware
Related ProVision
display poe power-usage
show power-over-ethernet brief
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the power information of the PoE power and all PSEs.
HP Switch# display poe power-usage
PoE Current Power
: 0 W
PoE Max Power
: 37 W
PoE Max Guaranteed Power
: 0 W
PoE Remaining Allocated Power
: 0 W
PoE Remaining Guaranteed Power
: 0 W
PoE Total Powered Port Number
: 0 W
Detailed power usage of PSE(s):
PSE ID Max
Current Peak
Average
(W)
(W)
(W)
(W)
7
37
0
0
0
10
37
0
0
0
Remaining
Powered
Guaranteed(W) PortNum
37
0
37
0
Example of Related ProVision Software Command Output.
HP Switch# show power-over-ethernet brief
Status and Counters - Port Power Status
System Power Status : No redundancy
PoE Power Status : No redundancy
Available: 300 W Used: 0 W Remaining: 300 W
Module A Power
Available: 300 W Used: 5 W Remaining: 295 W
PoE
| Power Power
Alloc Alloc Actual
Port
| Enable Priority By
Power Power
------ + ------ -------- ----- ----- -----A1
| Yes
low
usage 17 W 5.0 W
A2
| Yes
low
usage 17 W 0.0 W
A3
| Yes
low
usage 17 W 0.0 W
A4
| Yes
low
usage 17 W 0.0 W
A5
| Yes
low
usage 17 W 0.0 W
A6
| Yes
low
usage 17 W 0.0 W
Configured
Type
----------Phone1
Detection
Status
----------Delivering
Searching
Searching
Searching
Searching
Searching
Power
Class
----1
0
0
0
0
0
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
242 Display Commands
display poe-power alarm
Comware
Related ProVision
display poe-power alarm
show system power-supply
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays detailed alarm information about the PoE PSUs.
HP Switch# display poe-power alarm
PSU alarm detail, PSU number : 2
PSU 1 alarm : POWERED
PSU 2 alarm : POWERED
Example of Related ProVision Software Command Output.
HP Switch# show system power-supply
Power Supply Status:
PS# | State
| AC/DC + V | Wattage
----+-------------+-----------------+--------1 | Powered
| AC 120VDL | 875
2 | Not Present | -- ---| 0
1 / 2 supply bays delivering power.
Total power: 875 W
Minimum Software Version: 15.10.
display poe-power alarm 243
display poe-power switch state
Comware
Related ProVision
display poe-power switch state
No equivalent ProVision software command
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays the number and current state of the AC power distribution switches of the PSUs.
HP Switch# display poe-power switch state
Switch Number
: 3
Switch 1 State
: AC Switch Off
Switch 2 State
: AC Switch High Voltage
Switch 3 State
: AC Switch Off
Minimum Software Version: 15.10.
244 Display Commands
display port trunk
Comware
Related ProVision
display port trunk
No equivalent ProVision software command
Displays information about the hybrid or trunk ports on the switch, including port names, default
VLAN IDs (untagged vlan), and allowed VLAN IDs (tagged vlan).
HP Switch# display port trunk
Interface
PVID VLAN passing
A1
1
1-2, 5-10
A2
10
1, 5
Minimum Software Version: 15.10.
display port trunk 245
display power
Comware
Related ProVision
display power
show system power-supply
Displays information about the power supply of a device.
HP Switch# display power
Power
1 State: Powered
Power
2 State: Powered
Power
3 State: Not Present
Power
4 State: Not Present
Field Descriptions
Power: Number of power supply bay.
State: State of power supply.
Example of Related ProVision Software Command Output.
HP Switch(config)# show system power-supply
Power Supply Status:
PS# |
State
|
AC/DC + V
| Wattage
----+-------------+-----------------+--------1 | Powered
| -- ---|
0
1 / 1 supply bays delivering power.
display power Field Mappings.
Comware
ProVision Software
Power
PS#
State
State
246 Display Commands
display protocol-vlan
Comware
Related ProVision
display protocol-vlan
No equivalent ProVision software command
Displays the protocols and protocol indexes configured on the specified VLANs.
HP Switch# display protocol-vlan
VLAN ID:10
Protocol Index
Protocol Type
=============================================
1
IPv4
2
IPX
3
ARP
Minimum Software Version: 15.10.
display protocol-vlan 247
display protocol-vlan interface
Comware
Related ProVision
display protocol-vlan interface
No equivalent ProVision software command
Displays information about protocol-based VLANs on all ports.
HP Switch# display protocol-vlan interface all
Interface: A1
VLAN ID
Protocol Index
Protocol Type
======================================================
2
2
IPX
Interface: F24
VLAN ID
Protocol Index
Protocol Type
======================================================
4
5
Appletalk
4
1
IPv4
4
6
SNA
Minimum Software Version: 15.10.
248 Display Commands
display proxy-arp
Comware
Related ProVision
display proxy-arp
show ip
Displays the proxy ARP status. If an interface is specified, proxy ARP status of the specified interface
is displayed; if no interface is specified, proxy ARP status of all interfaces is displayed.
HP Switch# display proxy-arp
VLAN30
Proxy ARP status: disabled
VLAN33
Proxy ARP status: disabled
Operating Notes
For more information, see the “IP Routing Features” chapter in the latest Multicast and Routing
Guide for your switch.
Minimum Software Version: 15.11.
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip
Internet (IP) Service
IP Routing : Disabled
Default TTL
: 64
Arp Age
: 20
Domain Suffix
:
DNS server
:
VLAN
| IP Config IP Address
Subnet Mask
Proxy ARP
-------------------- + ---------- --------------- --------------- --------DEFAULT_VLAN
| DHCP/Bootp 15.255.157.54
255.255.248.0
Yes Yes
VLAN2100
| Disabled
display proxy-arp 249
display public-key local rsa public
Comware
Related ProVision
display public-key local rsa public
show crypto host-public-key
show ip host-public-key
Displays public key information of the local key pairs. This command is available only in manager
mode.
HP Switch# display public-key local rsa public
=====================================================
Time of Key pair created: 16:53:41 2012/05/08
Key name: HOST_KEY
Key type: RSA Encryption Key
=====================================================
Key code:
30819F300D06092A864886F70D010101050003818D0030818902818100C37
1A8F1C7BAC3B7BD9003
B9B0F8F2D77980D160B998227F75F395CAD5663EEF16F9DC71CBD22149439
F2BAC388B0F19714146
3129E6A5B83692D914A7DA8F34F0B8CB2C71C9DD7301D7231993AD3576507
31D4DC40B1DE825CB5B
6FE8ED963AD7DFCF9AEF4A5E76DDBBA1ADD8AB533A4335963CE88825F7FFB
1CB1F6DA5505D020301
0001
=====================================================
Time of Key pair created: n/a
Key name: SERVER_KEY
Key type: RSA Encryption Key
=====================================================
Key code:
n/a
Example of Related ProVision Software Command Output.
HP Switch# show crypto host-public-key
SSH host public key:
ssh-rsa
AAAAB3NzaC1yc2EAAAADAQABAAABAQDNwBMXZ9vYG+YxtV+KQeQQ+R8RKx47l
xs14jPImBoV
qUmK1iyK3WGhv0Fsks9ZtATjidybwPjmfd2Lup1INUjemquL2C0YRXo4MULfr
qioWTco4mlFliftypj5
gLvYeYFT/
9CpoxMF4YrTUyjc90UfIf3et3fahaZ4KgLQjnXV1b8AWWsDZRv7niq8A1emqg
ts3HuAk59L
vFYsMkvLV2a7qoks1auqW8otRHgv/
QsWtxfuoYUvVnXDiZFKeent34+sQnIvy1wJAmukCmM3zp434eTe
h87/2Oer612mlAwRq5qPFtTAZlsf8LGipjKftW6dq8uq9tYtTtQWO09Mi65L
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
250 Display Commands
display public-key peer
Comware
Related ProVision
display public-key peer
show ip client-public-key
Displays brief information about all the public keys of remote hosts.
HP Switch# display public-key peer
Key Name : "rsa-key-20120206"
Key Type : RSA
Key Module : 1024
Key Code : raky2100"shraAABNa1cEAAJAABm2ufBHv80BmMgle//
m9Hq8N4B1c+N1i3eUfyLN4bZBi2cIEXNU/
cXDUo3FINB8k+xb2fhNfIQ8rT0Q0Y/a+XR=
Field Descriptions
Key name: Key name, which can be one of the following values:
•
HOST_KEY: Host public key
•
SERVER_KEY: Server public key. This value is available only for RSA key pairs.
Key type: Key type, which can be one of the following values:
•
RSA Encryption Key: RSA key pair
•
DSA Encryption Key: DSA key pair
Key code: Key data
Example of Related ProVision Software Command Output.
HP Switch# show crypto client-public-key
Operator keys:
0,kchaitan@hpnsw190.rose.hp.com ssh-rsa
AAAAB3NzaC1yc2EAAAABIwAAAQEAsGffNl6CFBtxgEPExkZwbauXCiBLnzztD
5qA2IafkQzOy22gMDAl6rinTXvDcdP6P+RDGX+76p0E4IabwnmdpdSX+jCCV7
PDjYumrAomXF9uZ+6Mg6xkAURoXdisSwTiY9jeNyfCLrcLGy+4i9B2YEz3IO0
qH7D8ciwfhTbkEnOCLIFGSYzGUGsbXbHRTd6prOogAIJg1lnXjSXLgHikdAtL
FNNDwTXnxvX0SE02zeVehAb8XNHwZc6vy5FneKGjH9waq/
TEEqVJPwAJ6A5diuUvaFlAQGj53y4QqdaMORcfRXMfGtOCsEx/
jX5pmJAJ7MsB/NX1AHSowgRUaIR0qw==
display public-key peer
251
display radius scheme
Comware
Related ProVision
display radius scheme
show radius
show radius host <host>
show accounting
Displays the configuration information of RADIUS schemes.
HP Switch# display radius scheme
-----------------------------------------------------------------SchemeName
: n/a
Index : n/a
Type : n/a
Primary Auth Server :
IP : 1.2.3.4
Port : 1812 State : n/a
Encryption Key : samplee123
VPN instance
: n/a
Primary Acct Server :
IP : 1.2.3.4
Port : 1813 State : n/a
Encryption Key : samplee123
VPN instance
: n/a
Second Auth Server
IP : 2.3.4.5
Port : 1812 State : n/a
Encryption Key : ghefijklm
VPN instance
: n/a
IP : 4.5.6.7
Port : 1812 State : n/a
Encryption Key : abcdegh
VPN instance
: n/a
IP : 4.5.6.8
Port : 1812 State : n/a
Encryption Key : abcdegh
VPN instance
: n/a
Second Acct Server
IP : 2.3.4.5
Port : 1813 State : n/a
Encryption Key : ghefijklm
VPN instance
: n/a
IP : 4.5.6.7
Port : 1813 State : n/a
Encryption Key : abcdegh
VPN instance
: n/a
IP : 4.5.6.8
Port : 1813 State : n/a
Encryption Key : abcdegh
VPN instance
: n/a
Auth Server Encryption Key :
Acct Server Encryption Key :
VPN instance
: n/a
Accounting-On packet disable, send times : n/a , interval : n/a
Interval for timeout(second)
: 5
Retransmission times for timeout
: 3
Interval for realtime accounting(minute)
: 0
Retransmission times of realtime-accounting packet
: 3
Retransmission times of stop-accounting packet
: 3
Quiet-interval(min)
: 0
Username format
: n/a
Data flow unit
: n/a
Packet unit
: n/a
NAS-IP address
: n/a
Attribute 25
: n/a
-----------------------------------------------------------------Total 1 RADIUS scheme(s).
252 Display Commands
Field Descriptions
SchemeName: Name of the RADIUS scheme.
Index: Index number of the RADIUS scheme.
Type: Type of the RADIUS server, extended or standard.
Primary Auth Server: Information about the primary authentication server.
Primary Acct Server: Information about the primary accounting server.
Second Auth Server: Information about the secondary authentication server.
Second Acct Server: Information about the secondary accounting server.
IP: Ip address of the server.
Port: Service port of the server. If no port configuration is performed, the default port number is
displayed.
State: Status of the server, active or blocked.
Encryption Key: Shared key for authenticating authentication or accounting packets, in cipher text
or plain text. If no shared key is configured, the value of this field is N/A. This shared key is used
only when no specific shared key is specified for the RADIUS server.
VPN instance: MPLS L3VPN that the server belongs to. If no VPN instance is specified for the server,
the value of this field is N/A.
Auth Server Encryption Key: Shared key for authenticating authentication packets, in cipher text
or plain text.
Acct Server Encryption Key: Shared key for authenticating accounting packets, in cipher text or
plain text.
Accounting-On packet disable: The accounting-on feature is disabled.
send times: Retransmission times of accounting-on packets.
interval: Interval at which the device retransmits accounting-on packets.
Interval for timeout (second): RADIUS server response timeout period, in seconds.
Retransmission times for timeout: Maximum number of attempts for transmitting a RADIUS packet
to a single RADIUS server.
Interval for realtime accounting(minute): Interval for realtime accounting, in minutes.
Retransmission times of realtime-accounting packet: Maximum number of accounting attempts
Retransmission times of stop-accounting packet: Maximum number of stopaccounting attempts
Quiet-interval(min): Quiet interval for the primary server.
Username format: Format of the usernames to be sent to the RADIUS server.
Data flow unit: Unit for data flows sent to the RADIUS server.
Packet unit: Unit for packets sent to the RADIUS server.
NAS-IP address: Source IP address for RADIUS packets to be sent.
Attribute 25: Interprets RADIUS attribute 25 as the CAR parameters.
Operating Notes
For more information on switch RADIUS operation, see the "RADIUS Authentication, Authorization,
and Accounting" chapter in the latest Access Security Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch# show radius
Status and Counters - General RADIUS Information
display radius scheme 253
Deadtime(min) : 5
Timeout(secs) : 10
Retransmit Attempts :
Global Encryption Key
Dynamic Authorization
Source IP Selection :
2
: myg10balkey
UDP Port : 3799
Outgoing Interface
Auth Acct DM/
Server IP Addr Port Port CoA
--------------- ---- ---- --192.33.12.65
1812 1813 No
Time
Window Encryption Key
OOBM
------ -------------------------------- ----300
my65key
No
HP Switch(config)# show radius host 192.33.12.65
Status and Counters - RADIUS Server Information
Server IP Addr : 192.33.12.65
Authentication UDP Port : 1812 Accounting UDP Port
Round Trip Time
: 2
Round Trip Time
Pending Requests
: 0
Pending Requests
Retransmissions
: 0
Retransmissions
Timeouts
: 0
Timeouts
Malformed Responses
: 0
Malformed Responses
Bad Authenticators
: 0
Bad Authenticators
Unknown Types
: 0
Unknown Types
Packets Dropped
: 0
Packets Dropped
Access Requests
: 2
Accounting Requests
Access Challenges
: 0
Accounting Responses
Access Accepts
: 0
Access Rejects
: 0
HP Switch(config)# show accounting
Status and Counters - Accounting Information
Interval(min) : 5
Suppress Empty User : No
Sessions Identification : Common
Type
-------Network
Exec
System
Commands
|
+
|
|
|
|
Method
-----None
Radius
Radius
Radius
Mode
Server Group
-------------- -----------Start-Stop
Stop-Only
Interim-Update
display radius scheme Field Mappings.
Comware
ProVision Software
SchemeName
n/a
Index
n/a
Type
n/a
Primary Auth Server
Server IP Address
Primary Acct Server
Server IP Address
Second Auth Server
n/a
Second Acct Server
n/a
IP
Server IP Address
Port
Auth Port or Acct Port
State
n/a
254 Display Commands
:
:
:
:
:
:
:
:
:
:
: 1813
7
0
0
0
0
0
0
0
2
2
Comware
ProVision Software
Encryption Key
Encryption Key
VPN instance
n/a
Auth Server Encryption Key
n/a
Acct Server Encryption Key
n/a
Accounting-On packet disable, send times
n/a
Interval for timeout (sec)
Timeout (secs)
Retransmission times for timeout
n/a
Interval for realtime accounting (minute)
Interval(min)
Retransmission times of realtime-accounting packet
n/a
Retransmission times of stop-accounting packet
n/a
Quiet-interval(min)
Deadtime (min)
Username format
n/a
Data flow unit
n/a
Packet unit
n/a
NAS-IP address
n/a
Attribute 25
n/a
n/a
Retransmit Attempts
n/a
Dynamic Authorization UDP Port
n/a
Source IP Selection
display radius scheme 255
display rip
Comware
Related ProVision
display rip
No equivalent ProVision software command
Displays RIP configuration information. The command provides information regarding the version,
preference, cost, summary, maximum number of balanced paths, configured peers, number of
route changes and number of replies to queries in a RIP route.
HP Switch# display rip
Public VPN-instance name : n/a
RIP process : n/a
RIP version : 1
Preference : 120
checkzero : n/a
Default-cost : 1
Summary : Enabled
Hostroutes : n/a
Maximum number of balanced paths : 4
Update time : n/a
Timeout time
: n/a
Suppress time : n/a
Garbage-collect time : n/a
Update output delay : n/a
Output count : n/a
TRIP retransmit time : n/a
TRIP response packets retransmit count : n/a
Silent interfaces : n/a
Default routes : Disabled
Verify-source : Enabled
Networks : n/a
Configured peers : None
Triggered updates sent : 0
Number of route changes : 0
Number of replies to queries : 0
256 Display Commands
display rip interface
Comware
Related ProVision
display rip interface
No equivalent ProVision software command
Displays RIP interface information of the RIP process. If no interface is specified, information about
all RIP interfaces of the RIP process is displayed.
HP Switch# display rip 1 interface
Interface-name: Vlan-interface2
Address/Mask:2.2.2.2/24
Version:RIPv2
MetricIn:1
MetricIn route policy:n/a
MetricOut:0
MetricOut route policy:n/a
Split-horizon/Poison-reverse:on/on Input/Output:on/on
Default route:on
Current packets number/Maximum packets number:n/a
Interface-name: Vlan-interface3
Address/Mask:3.3.3.3/8
Version:RIPv1
MetricIn:1
MetricIn route policy:n/a
MetricOut:0
MetricOut route policy:n/a
Split-horizon/Poison-reverse:on/on Input/Output:on/on
Default route:on
Current packets number/Maximum packets number:n/a
Interface-name: Vlan-interface4
Address/Mask:192.168.4.55/16
Version:RIPv1 or RIPv2
MetricIn:1
MetricIn route policy:n/a
MetricOut:0
MetricOut route policy:n/a
Split-horizon/Poison-reverse:on/off Input/Output:on/on
Default route:on
Current packets number/Maximum packets number:n/a
HP Switch# display rip 1 interface vlan-interface 2
Interface-name: Vlan-interface2
Address/Mask:2.2.2.2/24
Version:RIPv2
MetricIn:1
MetricIn route policy:n/a
MetricOut:0
MetricOut route policy:n/a
Split-horizon/Poison-reverse:on/on Input/Output:on/on
Default route:on
Current packets number/Maximum packets number:n/a
Minimum Software Version: 15.10.
display rip interface 257
display rip process-id ip-address mask/mask-length
Comware
Related ProVision
display rip process-id ip-address mask/mask-length
No equivalent ProVision software command
Displays routes learnt by RIP. The command provides information regarding the peer address,
vlan-interface (to which the peer is connected), route destination, route destination mask, route
NextHop, route cost, route flags, route secs for all the routes that RIP has learnt.
HP Switch # display rip 1 route 20.0.0.0 8
Route Flags: R - RIP, T - TRIP
P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect
------------------------------------------------------------Peer 10.1.1.1 on Vlan-interface10
Destination/Mask
20.0.0.0/8
258 Display Commands
Nexthop
10.1.1.1
Cost
1
Tag
0
Flags
RA
Sec
5
display rip process-id route
Comware
Related ProVision
display rip process-id route
No equivalent ProVision software command
HP Switch# display rip 1 route
Route Flags: R - RIP, T - TRIP
P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect
----------------------------------------------------------------Peer 10.1.1.1 on Vlan-interface10
Destination/Mask
Nexthop
Cost
Tag
Flags
Sec
5.0.0.0/8
10.1.1.1
2
0
RA
5
6.0.0.0/8
10.1.1.1
1
0
RA
5
20.0.0.0/8
10.1.1.1
1
0
RA
5
display rip process-id route 259
display rip process-id route peer ip-address
Comware
Related ProVision
display rip process-id route peer ip-address
No equivalent ProVision software command
HP Switch# display rip 1 route peer 10.1.1.1
Route Flags: R - RIP, T - TRIP
P - Permanent, A - Aging, S - Suppressed, G - Garbage-collect
----------------------------------------------------------------Peer 10.1.1.1 on Vlan-interface10
Destination/Mask
5.0.0.0/8
6.0.0.0/8
20.0.0.0/8
260 Display Commands
Nexthop
10.1.1.1
10.1.1.1
10.1.1.1
Cost
2
1
1
Tag
0
0
0
Flags
RA
RA
RA
Sec
5
5
5
display rmon statistics
Comware
Related ProVision
display rmon statistics
show rmon statistics
Displays rmon statistics for the remote monitoring statistics information.
HP Switch# display rmon statistics A1
EtherStatsEntry 1 owned by monitor: is 1
Interface:A1
etherStatsOctets
: 3724
, etherStatsPkts
etherStatsBroadcastPkts
: 4
, etherStatsMulticastPkts
etherStatsUndersizePkts
: 0
, etherStatsOversizePkts
etherStatsFragments
: 0
, etherStatsJabbers
etherStatsCRCAlignErrors : 0
, etherStatsCollisions
etherStatsDropEvents(insufficient resources)
: 0
Packets received according to length:
64
: 12
, 65-127
: 0
, 128-255
: 8
256-511 : 4
, 512-1023 : 0
, 1024-1518 : 0
:
:
:
:
:
24
15
0
0
0
Operating Notes
For more information, refer to the latest Command Line Interface Reference Guide for your switch.
Minimum Software Version: 15.10.
display rmon statistics
261
display route-policy
Comware
Related ProVision
display route-policy
show route-map
Displays FIPS state. By default, the FIPS mode is disabled.
HP Switch# display route-policy
Route-Policy : qwer
permit :10
if-match community abcd
permit :11
if-match interface vlan 2
if-match ip-nexthop Prefix test
if-match ipv6-route-source abcd
if-match ipv6-address test
if-match local-preference 32
if-match metric 44
if-match routetype external 2
if-match sourceprotocol static
if-match tag 33
if-match community none
if-match ip-nexthop 1.2.3.4
if-match ipv6-nexthop 2001:db8:85a3::8a2e:370:7334
if-match as-path test
apply origin egp
Route-Policy : test
permit :12
if-match community test
deny :20
apply metric 3
apply tag 33
apply asPathPrepend
apply weight 44
Example of Related ProVision Software Command Output.
HP Switch# show route-map Map3
Routemap information
route-map
match
match
exit
route-map
match
match
exit
"Map3" permit seq 10
interface vlan 11 12 13
metric 25
"Map3" permit seq 20
interface vlan 21 22 23
metric 25
For more information, see the latest Multicast and Routing Guide for your switch.
262 Display Commands
display saved-configuration
Comware
Related ProVision
display saved-configuration
show config
Displays contents of the configuration file saved for the next startup of the switch.
HP Switch# display saved-configuration
; J8697A Configuration Editor; Created on release #K.15.09.0000x
; Ver #03:01.1f.ef:f2
hostname "HP-5406zl"
module 1 type J9536A
module 6 type J9534A
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged A1-A22,F1-F24
ip address dhcp-bootp
exit
Example of Related ProVision Software Command Output.
HP Switch# show config
Startup configuration:
; J8697A Configuration Editor; Created on release #K.14.01
hostname "HP Switch"
module 1 type J8705A
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged A1-A24
ip address dhcp-bootp
exit
interface A1
rate-limit all out kbps 200
exit
interface A2
rate-limit all out kbps 200
exit
interface A3
rate-limit all out kbps 200
exit
interface A4
rate-limit all out kbps 200
exit
interface A5
rate-limit all in percent 200
exit
interface A6
rate-limit icmp percent 60
rate-limit mcast in percent 60
exit
For more information, see the latest Management and Configuration Guide for your switch.
display saved-configuration 263
display saved-configuration by-linenum
Comware
Related ProVision
display saved-configuration by-linenum
show config
Displays the saved configuration of the switch with the line number. This command adds the line
number to the output of display saved-configuration. This command is available only in manager
mode.
HP Switch# display saved-configuration by-linenum
; J8692A Configuration Editor; Created on release #K.15.09.0000x
; Ver #03:01.1f.ef:f2
1: hostname "HP-E3500yl-24G"
2: module 1 type J86xxA
3: snmp-server community "public" Unrestricted
4: vlan 1
5: name "DEFAULT_VLAN"
6: untagged 1-24
7: ip address dhcp-bootp
8: exit
Example of Related ProVision Software Command Output.
HP Switch# show config
Startup configuration:
; J8697A Configuration Editor; Created on release #K.14.01
hostname "HP Switch"
module 1 type J8705A
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
untagged A1-A24
ip address dhcp-bootp
exit
interface A1
rate-limit all out kbps 200
exit
interface A2
rate-limit all out kbps 200
exit
interface A3
rate-limit all out kbps 200
exit
interface A4
rate-limit all out kbps 200
exit
interface A5
rate-limit all in percent 200
exit
interface A6
rate-limit icmp percent 60
rate-limit mcast in percent 60
exit
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
264 Display Commands
display schedule reboot
Comware
Related ProVision
display schedule reboot
show reload < after | at >
Displays the user-configured switch reboot (reload) time. For example, if the current date and time
is March 21, 2012 at 1:05 PM (13:05), and the switch is configured to reboot (reload) at 5:00
PM (17:00) on the same date, then you would see the following output when executing this
command:
HP Switch(config)# display schedule reboot
System will reboot at 17:00 03/21/2012 (in 3 hours and 55
minutes).
Operating Notes
To configure a reboot time on the switch, use the following command:
[no] reload [ after | at ]
For more on using the reload command, refer to the “Switch Memory and Configuration” chapter
in the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch(config)# show reload at
Reload scheduled for 17:00:52 02/21/2012
(in 0 days, 3 hours, 55 minutes)
display schedule reboot 265
display sflow display sflow slot <slot-number>
Comware
Related ProVision
display sflow
sh sflow agent
display sflow slot <slot-number>
sh sflow <receiver table number> sampling-polling
Displays the sflowglobal, collector and port information.
HP Switch# display sflow
sFlow Version: 1.3;HP;K.15.10.0000x
sFlow Global Information:
Agent
IP:120.93.219.32(Auto)
Collector Information:
ID
IP
Port
Aging Size Description
1
1.2.3.4
1
2147483512 1400
n/a
2
1.2.3.5
2
2147483525 1400
n/a
3
1.2.3.6
3
2147483547 1400
n/a
sFlow Port Information:
Interface CID Interval(s) FID MaxHLen Rate Mode
A4
1 0
1
128
51 Random
A5
2 0
2
128
52 Random
A6
3 0
3
128
53 Random
C1
2 0
2
128
88 Random
F10
1 0
1
128
77 Random
Status
Inactive
Inactive
Inactive
Active
Inactive
HP Switch# display sflow
sFlow Version: 1.3;HP;K.15.10.0000x
sFlow Global Information:
Agent
IP:120.93.219.32(Auto)
Collector Information:
ID
IP
Port
Aging Size Description
1
1.2.3.4
1
2147483512 1400
n/a
2
1.2.3.5
2
2147483525 1400
n/a
3
1.2.3.6
3
2147483547 1400
n/a
sFlow Port Information:
Interface CID Interval(s) FID MaxHLen Rate Mode
A4
1 0
1
128
51 Random
A5
2 0
2
128
52 Random
A6
3 0
3
128
53 Random
Status
Inactive
Inactive
Inactive
Example of Related ProVision Software Command Output.
HP Switch# sh sflow agent
Version
: 1.3;HP;K.15.10.0000x
Agent Address
: 120.93.219.32
Source IP Selection : Outgoing Interface
HP Switch# sh sflow 1 sampling-polling
Port
| Sampling
Dropped
| Polling
| Enabled Rate
Header Samples
| Enabled Interval
----- + ------- -------- ------ ---------- + ------- -------A1
--------Yes(1)
21
A4
Yes(1)
51
128
0
----F10
Yes(1)
77
128
0
-----
266 Display Commands
display snmp-agent community
Comware
Related ProVision
display snmp-agent community
show snmpv3 community
Displays community information for SNMPv1 or SNMPv2. This command is available only in
manager mode.
HP Switch# display snmp-agent community
Community name: public
Group name: n/a
Storage-type: volatile
Example of Related ProVision Software Command Output.
HP Switch# show snmpv3 community
snmpCommunityTable [rfc2576]
Index Name
---------1
2
3
30
Community Name Security Name
--------------- -----------------------public
CommunityManagerReadWrite
Operator
CommunityOperatorReadOnly
Manager
CommunityManagerReadWrite
Operator
CommunityManagerReadWrite
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display snmp-agent community 267
display snmp-agent group
Comware
Related ProVision
display snmp-agent group
show snmpv3 group
Displays information for the SNMPv3 agent group, including group name, security model, MIB
view, and storage type. Absence of the group-name parameter indicates that information for all
groups is displayed.
HP Switch# display snmp-agent group
Group name: ComManagerR
Security model: v1 noAuthnoPriv
Readview: ManagerReadView
Writeview: DiscoverView
Notifyview: ManagerReadView
Storage-type: ReadOnly
Group name: ComManagerR
Security model: v2 noAuthnoPriv
Readview: ManagerReadView
Writeview: DiscoverView
Notifyview: ManagerReadView
Storage-type: ReadOnly
Group name: ManagerAuth
Security model: v3 AuthnoPriv
Readview: ManagerReadView
Writeview: ManagerWriteView
Notifyview: ManagerReadView
Storage-type: ReadOnly
Group name: ManagerPriv
Security model: v3 AuthPriv
Readview: ManagerReadView
Writeview: ManagerWriteView
Notifyview: ManagerReadView
Storage-type: ReadOnly
Group name: ComManagerRW
Security model: v1 noAuthnoPriv
Readview: ManagerReadView
Writeview: ManagerWriteView
Notifyview: ManagerReadView
Storage-type: ReadOnly
Group name: ComManagerRW
Security model: v2 noAuthnoPriv
Readview: ManagerReadView
Writeview: ManagerWriteView
Notifyview: ManagerReadView
Storage-type: ReadOnly
Group name: ComOperatorR
Security model: v1 noAuthnoPriv
Readview: OperatorReadView
Writeview: DiscoverView
Notifyview: OperatorReadView
Storage-type: ReadOnly
Group name: ComOperatorR
Security model: v2 noAuthnoPriv
Readview: OperatorReadView
Writeview: DiscoverView
Notifyview: OperatorReadView
Storage-type: ReadOnly
Group name: OperatorAuth
Security model: v3 AuthnoPriv
Readview: OperatorReadView
Writeview: DiscoverView
268 Display Commands
Notifyview: OperatorReadView
Storage-type: ReadOnly
Group name: ComOperatorRW
Security model: v1 noAuthnoPriv
Readview: OperatorReadView
Writeview: OperatorReadView
Notifyview: OperatorReadView
Storage-type: ReadOnly
Group name: ComOperatorRW
Security model: v2 noAuthnoPriv
Readview: OperatorReadView
Writeview: OperatorReadView
Notifyview: OperatorReadView
Storage-type: ReadOnly
Group name: OperatorNoAuth
Security model: v3 noAuthnoPriv
Readview: OperatorReadView
Writeview: DiscoverView
Notifyview: OperatorReadView
Storage-type: ReadOnly
Example of Related ProVision Software Command Output.
HP Switch# show snmpv3 group
Status and Counters - SNHP v3 Global Configuration Information
Security Name
Security Model Group Name
------------------------ -------------- ----------------CommunityManagerReadOnly
ver1
ComManagerR
CommunityManagerReadWrite
ver1
ComManagerRW
CommunityOperatorReadOnly
ver1
ComOperatorRW
CommunityOperatorReadWrite
ver1
ComOperatorRW
CommunityManagerReadOnly
ver2c
ComManagerR
CommunityManagerReadWrite
ver2c
ComManagerRW
CommunityOperatorReadOnly
ver2c
ComOperatorRW
CommunityOperatorReadWrite
ver2c
ComOperatorRW
NetworkMgr
ver3
ManagerPriv
NetworkAdmin
ver3
OperatorNoAuth
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display snmp-agent group 269
display snmp-agent local-engineid
Comware
Related ProVision
display snmp-agent local-engineid
show snmpv3 engineid
Displays the SNMP agent local engine ID.
HP Switch# display snmp-agent local-engineid
SNMP local EngineID: 0000000b0000001871c42f00
Field Descriptions
SNMP local EngineID: Identifies an SNMP entity uniquely within an SNMP domain.
Operating Notes
There is no specific user configuration command for SNMP agent local engine ID.
For more on switch SNMP operation, refer to the “Configuring for Network Management
Applications” chapter in the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.08.
Example of Related ProVision Software Command Output.
HP Switch# HP Switch# show snmpv3 engineid
Status and Counters - SNMP v3 EngineId Information
EngineId: 00:00:00:0b:00:00:00:18:71:c4:2f:00
snmp-agent local-engineid Field Mappings.
Comware
ProVision Software
SNMP local EngineID
EngineID
270 Display Commands
display snmp-agent mib-view
Comware
Related ProVision
display snmp-agent mib-view
show snmpv3 group
Displays the View name, MIB Subtree, Subtree mask, Storage-type, View Type, and View status.
This command is available only in manager mode.
HP Switch# display snmp-agent mib-view
View name: DiscoverView
MIB Subtree: 1.3.6.1.6.3.15.1.2.2.1.7
Subtree mask:
Storage-type: readOnly
View Type: included
View status: notInService
Storage-type: readOnly
View name: DiscoverView
MIB Subtree: 1.3.6.1.6.3.15.1.2.2.1.10
Subtree mask:
Storage-type: readOnly
View Type: included
View status: notInService
Example of Related ProVision Software Command Output.
HP Switch# show snmpv3 group
Status and Counters - SNHP v3 Global Configuration Information
Security Name
Security Model
------------------------ -------------CommunityManagerReadOnly
ver1
CommunityManagerReadWrite
ver1
CommunityOperatorReadOnly
ver1
CommunityOperatorReadWrite
ver1
CommunityManagerReadOnly
ver2c
CommunityManagerReadWrite
ver2c
CommunityOperatorReadOnly
ver2c
CommunityOperatorReadWrite
ver2c
NetworkMgr
ver3
NetworkAdmin
ver3
Group Name
----------------ComManagerR
ComManagerRW
ComOperatorRW
ComOperatorRW
ComManagerR
ComManagerRW
ComOperatorRW
ComOperatorRW
ManagerPriv
OperatorNoAuth
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display snmp-agent mib-view
271
display snmp-agent statistics
Comware
Related ProVision
display snmp-agent statistics
No equivalent ProVision software command
Displays SNMP statistics, identifies SNMP PDUs, and provides information regarding the number
of PDUs in request, reply, get, set, errors and MIB retrieval and altered state.
HP Switch# display snmp-agent statistics
0 Messages delivered to the SNMP entity
0 Messages which were for an unsupported version
0 Messages which used a SNMP community name not known
0 Messages which represented an illegal operation for the community
supplied
0 ASN.1 or BER errors in the process of decoding
0 Messages passed from the SNMP entity
0 SNMP PDUs which had badValue error-status
0 SNMP PDUs which had genErr error-status
0 SNMP PDUs which had noSuchName error-status
0 SNMP PDUs which had tooBig error-status (Maximum packet size 1500)
10 MIB objects retrieved successfully
1 MIB objects altered successfully
0 GetRequest-PDU accepted and processed
0 GetNextRequest-PDU accepted and processed
0 GetBulkRequest-PDU accepted and processed
0 GetResponse-PDU accepted and processed
0 SetRequest-PDU accepted and processed
0 Trap PDUs accepted and processed
0 Alternate Response Class PDUs dropped silently
0 Forwarded Confirmed Class PDUs dropped silently
Minimum Software Version: 15.10.
272 Display Commands
display snmp-agent sys-info
Comware
Related ProVision
display snmp-agent sys-info
show system information
Displays current SNMP system information.
HP Switch# display snmp-agent sys-info
The contact person for this managed node:
admin
The physical location of this node:
HP
SNMP version running in the system:
SNMPv1 SNMPv2c SNMPv3
Example of Related ProVision Software Command Output.
HP Switch# show system information
Status and Counters - General System Information
System Name : HP Switch
System Contact :
System Location :
MAC Age Time (sec) : 300
Time Zone : 0
Daylight Time Rule : None
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
display snmp-agent sys-info 273
display snmp-agent trap-list
Comware
Related ProVision
display snmp-agent trap-list
show snmp-server traps
Displays modules that can generate traps and whether or not their trap function is enabled. This
command is available only in manager mode.
HP Switch# display snmp-agent trap-list
snmp Authentication trap extended
password change trap enable
login failures trap enable
port security trap enable
authorization server contact trap enable
dhcp-snooping trap enable
dynamic arp protection trap enable
dynamic ip lockdown trap enable
startup config change trap disable
running config change trap disable
mac address table changes trap disable
mac address count trap disable
Enable traps: 8; Disable traps: 4
Example of Related ProVision Software Command Output.
HP Switch# show snmp-server traps
Trap Receivers
Link-Change Traps Enabled on Ports [All] : A1-A24
Traps Category
Current Status
-------------------------- --------------SNMP Authentication
: Extended
Password change
: Enabled
Login failures
: Enabled
Port-Security
: Enabled
Authorization Server Contact : Enabled
DHCP Snooping
: Enabled
Dynamic ARP Protection
: Enabled
Dynamic IP Lockdown
: Enabled
Address
Community Events Sent Notify Type Retry Timeout
----------------- ------- ----------- ----------- ----- ------15.255.5.225
public
All
trap
3
15
2001:0db8:0000:0001
:0000:0000:0000:0121 user_1
All
trap
3
15
Excluded MIBs
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
274
Display Commands
display snmp-agent usm-user
Comware
Related ProVision
display snmp-agent usm-user
show snmpv3 user
Displays the snmp users configured in the system. This command is available only in manager
mode.
HP Switch# display snmp-agent usm-user
User name: user
Group name: ComOperatorR
Engine ID: 0000000B00000019BBBACD00
Storage-type: nonVolatile
UserStatus: active
User name: initial
Group name: ManagerPriv
Engine ID: 0000000B00000019BBBACD00
Storage-type: nonVolatile
UserStatus: active
Example of Related ProVision Software Command Output.
HP Switch# show snmpv3 user
Status and Counters - SNMP v3 Global Configuration Information
User Name
Auth. Protocol
Privacy Protocol
------------ ----------------------------initial
MD5
CFB AES-128
NetworkAdmin
MD5
CBC-DES
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
display snmp-agent usm-user 275
display ssh client source
Comware
Related ProVision
display ssh client source
No equivalent ProVision software command
Displays the source IP address or source interface currently set for the SSH client. If neither source
IP address nor source interface is specified for the SSH client, the system will prompt you to specify
the source information.
HP Switch# display ssh client source
Neither source IP address nor source interface was specified
for the STelnet client.
276 Display Commands
display ssh server session
Comware
Related ProVision
display ssh server session
show ip ssh
Displays SSH server session information. This command is available only in manager mode.
HP Switch# display ssh server session
Conn
A1
Ver
2.0
Encry
AES
State
Established
Retry
n/a
SerType
Stelnet
Username
manager
Example of Related ProVision Software Command Output.
HP Switch# show
SSH Enabled
TCP Port Number
Host Key Type
ip ssh
: Yes
: 22
: RSA
Secure Copy Enabled : No
Timeout (sec) : 120
Host Key Size : 2048
Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,
rijndael-cbc@lysator.liu.se,aes128-ctr,aes192-ctr,aes256-ctr
MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96
Ses Type
| Source IP
Port
--- -------- + -------------- ------1
console |
2
telnet |
3
ssh | 15.30.252.195
1531
4 inactive |
5 inactive |
6 inactive |
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
display ssh server session 277
display ssh server status
Comware
Related ProVision
display ssh server status
show ip ssh
Displays the SSH server status information or session information.
HP Switch# display ssh server status
SSH server : enabled
SSH version : 2
SSH authentication-timeout : 120 second(s)
SSH server key generating interval : n/a
SSH authentication retries : 3 time(s)
SFTP server : disabled
SFTP server Idle-Timeout : 0 minutes(s)
Field Descriptions
SSH server: Whether the SSH server function is enabled
SSH version: SSH protocol version. When the SSH supports SSH1, the protocol version is 1.99.
Otherwise, the protocol version is 2.0.
SSH authentication-timeout: Authentication timeout period
SSH server key generating interval: SSH server key pair update interval
SSH authentication retries: Maximum number of SSH authentication attempts
SFTP server: Whether the SFTP server function is enabled
SFTP server Idle-Timeout: SFTP connection idle timeout period
Example of Related ProVision Software Command Output.
HP Switch(config)# show ip ssh
SSH Enabled : Yes Secure Copy Enabled : No
TCP Port Number : 22 Timeout (sec) : 120
Host Key Type : RSA Host Key Size : 2048
Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,
rijndael-cbc@lysator.liu.se,aes128-ctr,aes192-ctr,aes256-ctr
MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96
Ses
Type
| Source IP
Port
---- --------+ -------------1 console
|
2 telnet
|
3 ssh
| 15.30.252.195
1531
4 inactive
|
5 inactive
|
6 inactive
|
For more information, see the latest Basic Operation Guide for your switch.
278 Display Commands
display ssh server-info
Comware
Related ProVision
display ssh server-info
No equivalent ProVision software command
Displays mappings between SSH servers and their host public keys saved on the client.
HP Switch# display ssh server-info
Server Name(IP)
Server public key name
-------------------------------------120.85.212.127
n/a
Minimum Software Version: 15.10.
display ssh server-info 279
display ssl client-policy
Comware
Related ProVision
display ssl client-policy
show ip ssh
Displays information about all SSL client policies. This command is available only in manager
mode.
HP Switch# display ssl client-policy
SSL Client Policy: n/a
SSL Version: TLS 1.0
PKI Domain: n/a
Prefer Ciphersuite:
aes256-ctr
aes256-cbc
rijndael-cbc@lysator.liu.se
aes192-ctr
aes192-cbc
aes128-ctr
aes128-cbc
3des-cbc
hmac-sha1-96
hmac-md5
hmac-sha1
hmac-md5-96
aes192-ctr
aes192-cbc
aes128-ctr
aes128-cbc
3des-cbc
Server-verify: n/a
Total 1 SSL client policy(s).
Example of Related ProVision Software Command Output.
HP Switch# show
SSH Enabled
TCP Port Number
Host Key Type
ip ssh
: Yes
: 22
: RSA
Secure Copy Enabled : No
Timeout (sec) : 120
Host Key Size : 2048
Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,
rijndael-cbc@lysator.liu.se,aes128-ctr,aes192-ctr,aes256-ctr
MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96
Ses Type
| Source IP
Port
--- -------- + -------------- ------1
console |
2
telnet |
3
ssh | 15.30.252.195
1531
4 inactive |
5 inactive |
6 inactive |
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
280 Display Commands
display ssl server-policy
Comware
Related ProVision
display ssl server-policy
show ip ssh
Displays information about all SSL client policies. This command is available only in manager
mode.
HP Switch# display ssl server-policy
SSL Server Policy: n/a
PKI Domain: n/a
Ciphersuite:
aes256-ctr
aes256-cbc
rijndael-cbc@lysator.liu.se
aes192-ctr
aes192-cbc
aes128-ctr
aes128-cbc
3des-cbc
hmac-sha1-96
hmac-md5
hmac-sha1
hmac-md5-96
aes192-ctr
aes192-cbc
aes128-ctr
aes128-cbc
3des-cbc
Handshake Timeout: 120
Close-mode: n/a
Session Timeout: n/a
Session Cachesize: n/a
Client-verify: n/a
Client-verify weaken: n/a
Total 1 SSL server policy(s).
Example of Related ProVision Software Command Output.
HP Switch# show
SSH Enabled
TCP Port Number
Host Key Type
ip ssh
: Yes
: 22
: RSA
Secure Copy Enabled : No
Timeout (sec) : 120
Host Key Size : 2048
Ciphers : aes128-cbc,3des-cbc,aes192-cbc,aes256-cbc,
rijndael-cbc@lysator.liu.se,aes128-ctr,aes192-ctr,aes256-ctr
MACs : hmac-md5,hmac-sha1,hmac-sha1-96,hmac-md5-96
Ses Type
| Source IP
Port
--- -------- + -------------- ------1
console |
2
telnet |
3
ssh | 15.30.252.195
1531
4 inactive |
5 inactive |
6 inactive |
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
display ssl server-policy
281
Minimum Software Version: 15.10.
282 Display Commands
display startup
Comware
Related ProVision
display startup
No equivalent ProVision software command
Displays the configuration file used at the current system startup and the configuration file(s) to be
used at the next system startup.
HP Switch# display startup
Current startup saved-configuration file: flash:/svt-1.cfg
Next startup saved-configuration file for primary image: flash:/
svt-1.cfg
Next startup saved-configuration file for secondary image:
flash:/svt-2.cfg
Minimum Software Version: 15.10.
display startup 283
display stp
Comware
Related ProVision
display stp
show spanning-tree
Displays the MSTP status and statistics. Based on the MSTP status and statistics, you can analyze
and maintain the network topology or check whether MSTP is working normally.
Spanning-tree protocol is enabled
HP Switch# display stp
-------[CIST Global Info][Mode STP]------CIST Bridge
:32768.3ce5-a674-b433
Bridge Times
:Hello 2s MaxAge 20s FwDly 15s MaxHop 20
CIST Root/ERPC
:32768.3ce5-a674-b433 / 0
CIST RegRoot/IRPC
:32768.3ce5-a674-b433 / 0
CIST RootPortId
:0.0
BPDU-Protection
:disabled
Bridge ConfigDigest-Snooping
:disabled
TC or TCN received :0
Time since last TC :1 days 22h:48m:24s
----[PortA1(A1)][DOWN]---Port Protocol
:0
Port Role
:CIST Disabled Port
Port Priority
:128
Port Cost(Legacy)
:0
Desg. Bridge/Port
:32768.3ce5-a674-b433 / 128.1
Port Edged
:Config=disabled / Active=disabled
Point-to-point
:Config=auto / Active=false
Transmit Limit
:10 packets/hello-time
Protection Type
:None
MST BPDU Format
:0
Port ConfigDigest-Snooping
:0
Num of Vlans Mapped :1
PortTimes
:Hello 2s MaxAge 20s FwDly 15s
MsgAge 0s RemHop 20
BPDU Sent
:0
TCN: 0, Config: 0, RST: 0, MST: 0
BPDU Received
:0
TCN: 0, Config: 0, RST: 0, MST: 0
----[PortA2(A2)][DOWN]---.
.
.
----[PortA3(A3)][DOWN]---.
.
.
.
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree
Multiple Spanning Tree (MST) Information
STP Enabled : Yes
Force Version : MSTP-operation
IST Mapped VLANs : 1-4094
Switch MAC Address : 0024a8-d13a40
284 Display Commands
Switch Priority : 32768
Max Age : 20
Max Hops : 20
Forward Delay : 15
Topology Change Count : 1
Time Since Last Change : 20 mins
CST Root MAC Address : 001083-847000
CST Root Priority : 0
CST Root Path Cost : 60000
CST Root Port : 1
IST Regional Root MAC Address : 0024a8-d13a40
IST Regional Root Priority : 32768
IST Regional Root Path Cost : 0
IST Remaining Hops : 20
Root Guard Ports :
Loop Guard Ports : 2
TCN Guard Ports :
BPDU Protected Ports :
BPDU Filtered Ports :
PVST Protected Ports :
PVST Filtered Ports :
Prio
| Designated Hello
Port Type
| Cost rity State
| Bridge
Time PtP Edge
---- --------- ----- ------ -------------- --- ----1
100/1000T | 20000 128 Forwarding |001871-cdea00 2 Yes No
2
100/1000T | Auto 128 Inconsistent |
3
100/1000T | Auto 128 Disabled |
4
100/1000T | Auto 128 Disabled |
5
100/1000T | Auto 128 Disabled |
6
100/1000T | Auto 128 Disabled |
7
100/1000T | Auto 128 Disabled |
8
100/1000T | Auto 128 Disabled |
Comware supports instances ranging from 0-31 and ProVision supports instances ranging from
0-16. For more information, see the latest Advanced Traffic Management Guide for your switch.
display stp 285
display stp abnormal-port
Comware
Related ProVision
display stp abnormal-port
show spanning-tree detail
show spanning-tree <port> detail
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays information about ports blocked by spanning tree protection functions.
HP Switch# display stp abnormal-port
MSTID Blocked Port
Reason
1
A1
ROOT-Protected
2
A2
LOOP-Protected
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree detail
Status and Counters - CST Port(s) Detailed Information
Port : 1
Status : Up
...
Port : 2
Status : Up
BPDU Protection : No
BPDU Filtering : No
PVST Protection : No
PVST Filtering : No
Errant BPDU Count : 0
Root Guard : No
Loop Guard : Yes
TCN Guard : No
MST Region Boundary : Yes
External Path Cost : 20000
External Root Path Cost : 40000
Administrative Hello Time : Global
Operational Hello Time : 2
AdminEdgePort : No
Auto Edge Port : Yes
OperEdgePort : No
AdminPointToPointMAC : True
OperPointToPointMAC : Yes
Aged BPDUs Count : 0
Loop-back BPDUs Count : 0
TC ACK Flag Transmitted : 0
TC ACK Flag Received : 1
MST
MST
CFG
CFG
TCN
TCN
BPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx
-------- -------- -------- -------- -------- --------3
0
24354
1682
0
13
For more information, see the latest Advanced Traffic Management Guide for your switch.
286 Display Commands
display stp bpdu-statisticsdisplay stp bpdu-statistics interface GigabitEthernet
<port-num>display stp bpdu-statistics interface GigabitEthernet <port-num>
instance <instanceNUM, 1-32>
Comware
Related ProVision
display stp bpdu-statistics
show spanning-tree detail
display stp bpdu-statistics interface GigabitEthernet
<port-num>
display stp bpdu-statistics interface GigabitEthernet
<port-num> instance <instanceNUM, 1-32>
Displays the debug counters of the STP in different modes.
In MSTP mode :
•
If MSTI or port is not specified, this command displays the BPDU statistics of all MSTIs on all
ports. The displayed information is sorted by port name and by MSTI ID on each port.
•
If a port is specified but not an MSTI, this command displays the BPDU statistics of all MSTIs
on the port. The displayed information is sorted by MSTI ID.
•
If both an MSTI ID and a port are specified, this command displays the BPDU statistics of the
specified MSTI on the port.
In STP, RSTP, or PVST mode:
•
If no port is specified, this command displays the BPDU statistics of on all ports. The displayed
information is sorted by port name.
•
If a port is specified, this command displays the BPDU statistics on the port.
HP Switch# stp bpdu-statistics interface 2 instance 2
Port: 2
Instance-independent:
Type
--------------------------Invalid BPDUs
Looped-back BPDUs
MAX-aged BPDUs
TCN sent
TCN received
TCA sent
TCA received
Config sent
Config received
RST sent
RST received
MST sent
MST received
Count
Last Updated
---------- ----------------0
0
0
0
0
0
0
0
0
0
0
0
0
Instance 2:
Type
Count
Last Updated
--------------------------Timeout BPDUs
MAX-hoped BPDUs
TC detected
TC sent
TC received
---------- ----------------0
0
0
0
0
display stp bpdu-statisticsdisplay stp bpdu-statistics interface GigabitEthernet <port-num>display stp bpdu-statistics interface 287
GigabitEthernet <port-num> instance <instanceNUM, 1-32>
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree detail
Status and Counters - CST Port(s) Detailed Information
Port : 1
Status : Up
...
Port : 2
Status : Up
BPDU Protection : No
BPDU Filtering : No
PVST Protection : No
PVST Filtering : No
Errant BPDU Count : 0
Root Guard : No
Loop Guard : Yes
TCN Guard : No
MST Region Boundary : Yes
External Path Cost : 20000
External Root Path Cost : 40000
Administrative Hello Time : Global
Operational Hello Time : 2
AdminEdgePort : No
Auto Edge Port : Yes
OperEdgePort : No
AdminPointToPointMAC : True
OperPointToPointMAC : Yes
Aged BPDUs Count : 0
Loop-back BPDUs Count : 0
TC ACK Flag Transmitted : 0
TC ACK Flag Received : 1
MST
MST
CFG
CFG
TCN
TCN
BPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx BPDUs Tx BPDUs Rx
-------- -------- -------- -------- -------- --------3
0
24354
1682
0
13
For more information, see the latest Advanced Traffic Management Guide for your switch.
288 Display Commands
display stp briefdisplay stp instance <instance-id> briefdisplay stp instance
<instance-id> interface GigabitEthernet <interface-id> briefdisplay stp
instance <instance-id> interface GigabitEthernet <interface-id> briefdisplay
stp instance <instance-id> interface GigabitEthernet <interface-id> to
GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> slot
<slot-id> briefdisplay stp interface GigabitEnterface <port-num> briefdisplay
stp interface GigabitEnterface <port-num> to GigabitEnterface <port-num>
brief
Comware
Related ProVision
display stp brief
show spanning-tree config
display stp instance <instance-id> brief
show spanning-tree <PORT-LIST> detail
display stp instance <instance-id> interface
GigabitEthernet <interface-id> brief
display stp instance <instance-id> interface
GigabitEthernet <interface-id> brief
display stp instance <instance-id> interface
GigabitEthernet <interface-id> brief display stp instance
<instance-id> interface GigabitEthernet <interface-id> to
GigabitEthernet <interface-id> brief
display stp instance <instance-id> slot <slot-id> brief
display stp interface GigabitEnterface <port-num> brief
display stp interface GigabitEnterface <port-num> to
GigabitEnterface <port-num> brief
Displays brief information about spanning tree status and statistics.
Spanning-tree protocol is enabled
HP Switch# display stp brief
MSTID
Port
Role
STP State
1
1 Designated Blocking
2
2 Disabled
Disabled
Spanning-tree protocol is disabled
HP Switch# display stp brief
Protocol Status :disabled
Protocol Std. :IEEE 802.1s
Version :0
Bridge-Prio. :32768
MAC address :000fe2-008048
Max age(s) :20
Forward delay(s) :15
Hello time(s) :2
Max hops :20
Protection
No
No
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree config
Multiple Spanning Tree (MST) Configuration Information
STP Enabled [No] : Yes
Force Version [MSTP-operation] : MSTP-operation
Default Path Costs [802.1t] : 802.1t
MST Configuration Name : 1cc1decfbc80
MST Configuration Revision : 0 Switch Priority : 32768
Forward Delay [15] : 15 Hello Time [2] : 2
Max Age [20] : 20 Max Hops [20] : 20
| Path Prio Admin Auto Admin Hello Root TCN BPDU
display stp briefdisplay stp instance <instance-id> briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> 289
briefdisplay stp instance <instance-id> interface GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> interface
GigabitEthernet <interface-id> to GigabitEthernet <interface-id> briefdisplay stp instance <instance-id> slot <slot-id> briefdisplay
stp interface GigabitEnterface <port-num> briefdisplay stp interface GigabitEnterface <port-num> to GigabitEnterface
<port-num> brief
Port Type | Cost
---- ---- + ---1 10/100TX | Auto
2 10/100TX | Auto
3 10/100TX | Auto
. . . . . . . . .
7 10/100TX | Auto
rity Edge Edge PtP
Time Grd Grd Flt
---- ---- ----- ---- ----- ---- ---- --128
No Yes
True Global No
No No
128
No Yes
True Global No
No No
128
No Yes
True Global No
No No
. .
128
No Yes
True Global No
No No
ProVision accepts interface range as 1-8. Comware accpets interface range as
"GigabitEthernet1/0/1 to GigabitEthernet1/0/8".
CIST RootPortId and MSTI RootPortId are represented differently in ProVision and Comware.
For more information, see the latest Advanced Traffic Management Guide for your switch.
290 Display Commands
display stpdisplay stp instance <instance-id> interface GigabitEthernet
1/0/1/display stp slot <slot-num>
Comware
Related ProVision
display stp
show spanning-tree
display stp instance <instance-id> interface
GigabitEthernet 1/0/1/
display stp slot <slot-num>
Displays MSTP status and statistics.
HP Switch# display stp
Protocol Status
:
Protocol Std.
:
Version
:
CIST Bridge-Prio
:
MAC Address
:
Max age (s)
:
Forward delay (s) :
Hello Time(s)
:
Max Hops
:
Disabled
IEEE802.1s
3
32768
0021f7-06ab00
2000
1500
200
20
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree
Multiple Spanning Tree (MST) Information
STP Enabled : Yes
Force Version : MSTP-operation
IST Mapped VLANs : 1-4094
Switch MAC Address : 0024a8-d13a40
Switch Priority : 32768
Max Age : 20
Max Hops : 20
Forward Delay : 15
Topology Change Count : 1
Time Since Last Change : 20 mins
CST Root MAC Address : 001083-847000
CST Root Priority : 0
CST Root Path Cost : 60000
CST Root Port : 1
IST Regional Root MAC Address : 0024a8-d13a40
IST Regional Root Priority : 32768
IST Regional Root Path Cost : 0
IST Remaining Hops : 20
Root Guard Ports :
Loop Guard Ports : 2
TCN Guard Ports :
BPDU Protected Ports :
BPDU Filtered Ports :
PVST Protected Ports :
PVST Filtered Ports :
Prio
| Designated Hello
Port Type
| Cost rity State
| Bridge
Time PtP Edge
---- --------- ----- ---------------- ---- --- ----1
100/1000T | 20000 128 Forwarding |001871-cdea00 2 Yes No
2
100/1000T | Auto 128 Inconsistent |
3
100/1000T | Auto 128 Disabled |
4
100/1000T | Auto 128 Disabled |
5
100/1000T | Auto 128 Disabled |
6
100/1000T | Auto 128 Disabled |
display stpdisplay stp instance <instance-id> interface GigabitEthernet 1/0/1/display stp slot <slot-num>
291
7
8
100/1000T | Auto 128 Disabled |
100/1000T | Auto 128 Disabled |
For more information, see the latest Advanced Traffic Management Guide for your switch.
292 Display Commands
display stp down-port
Comware
Related ProVision
display stp down-port
No equivalent ProVision software command
Displays information about ports shut down by spanning tree protection functions.
HP Switch# display stp down-port
Down Port
Reason
4
BPDU-Protected
5
BPDU-Protected
Operating Notes
ProVision does not support Format-Frequency.
display stp down-port 293
display stp history display stp history slot <slot-number>display stp instance
<instance-id>history slot <slot-no>display stp instance <instance-id>history
Comware
Related ProVision
display stp history
No equivalent ProVision software command
display stp history displays the historical port role calculation information of all MSTIs.
display stp history slot slot-number displays the statistics of the port’s history information of all the
MSTIs of a given slot when stp protocol is enabled.
display stp instance instance-id history displays the historical port role information of the specified
MSTI when stp protocol is enabled.
display stp instance instance-id history slot slot-number displays the statistics of the port’s history
information of the specified MSTI of a given slot when stp protocol is enabled.
HP Switch# display stp history
display stp history
--------------- STP slot 1 history trace --------------------------------- Instance 0 ------------------Port 1
Role change
:Disa->Desi
Time
:2012/05/28 09:47:23
Port priority
:32768.002347-b4cb80 0 32768.002347-b4cb80 0
32768.002347-b4cb80 128.1
------------------- Instance 1 ------------------Port 1
Role change
:Disa->Desi
Time
:2012/05/28 09:47:23
Port priority :32768.002347-b4cb80 0 32768.002347-b4cb80 48.1
HP Switch# display stp history slot A
--------------- STP slot 1 history trace --------------------------------- Instance 0 ------------------Port 1
Role change
:Disa->Desi
Time
:2012/05/28 09:47:23
Port priority
:32768.002347-b4cb80 0 32768.002347-b4cb80 0
32768.002347-b4cb80 128.1
------------------- Instance 1 ------------------Port 1
Role change
:Disa->Desi
Time
:2012/05/28 09:47:23
Port priority
:32768.002347-b4cb80 0 32768.002347-b4cb80
48.1
HP Switch# display stp instance 0 history
--------------- STP slot 1 history trace --------------------------------- Instance 0 ------------------Port 1
Role change
:Disa->Desi
Time
:2012/05/28 09:47:23
Port priority
:32768.002347-b4cb80 0 32768.002347-b4cb80 0
32768.002347-b4cb80 128.1
Minimum Software Version: 15.10.
294 Display Commands
display stp instance <instanceid> tcdisplay stp instance <instanceid> tc
slot <slot-no>display stp tc
Comware
Related ProVision
display stp instance <instanceid> tc
No equivalent ProVision software command
display stp instance <instanceid> tc slot <slot-no>
display stp tc
Displays the STP information of a port under a particular instance when STP is enabled.
HP Switch# display stp instance 0 tc
-------------- STP slot A TC or TCN count ------------MSTID
Port
Receive
Send
0
A1
2
2
-------------- STP slot B TC or TCN count ------------MSTID
Port
Receive
Send
-------------- STP slot C TC or TCN count ------------MSTID
Port
Receive
Send
HP Switch# display stp instance 1 tc slot A
-------------- STP slot A TC or TCN count ------------MSTID
Port
Receive
Send
1
A2
0
2
HP Switch# display stp tc slot B
-------------- STP slot B TC or TCN count ------------MSTID
Port
Receive
Send
0
B1
2
2
1
B2
0
2
display stp instance <instanceid> tcdisplay stp instance <instanceid> tc slot <slot-no>display stp tc 295
display stp region-configuration
Comware
Related ProVision
display stp region-configuration
show spanning-tree mst-config
show spanning-tree mst-config
Spanning-tree protocol is enabled
HP Switch# display stp region-configuration
Oper Configuration
Format selector :0
Region name :hello
Revision level :0
Configuration digest :0x5f762d9a46311effb7a488a3267fca9f
Instance Vlans Mapped
0 21 to 4094
1 1 to 10
2 11 to 20
Spanning-tree protocol is diabled
HP Switch# display stp region-configuration
Oper configuration
Format selector :0
Region name :3ce5a6761a00
Revision level :0
Configuration digest :
Instance Vlans Mapped
1
1 to 4094
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree mst-config
MST Configuration Identifier Information
MST Configuration Name : 1cc1decfbc80
MST Configuration Revision : 0
MST Configuration Digest : 0xC8DB46AEBEA5F48799BD2D8B0E1BCA54
IST Mapped VLANs : 1-110,112-299,301-4094
Instance ID Mapped VLANs
----------- ------------------------------------------------11 111,300
For more information, see the latest Advanced Traffic Management Guide for your switch.
296 Display Commands
display stp root
Comware
Related ProVision
display stp root
show spanning-tree instance <instance-id>
show spanning-tree detail
Displays the root bridge information of all MSTIs.
Spanning-tree protocol is enabled
HP Switch# display stp root
MSTID Root Bridge ID ExtPathCost IntPathCost Root Port
0 00e0fc-0e6554 200200 0 A1
Spanning-tree protocol is disabled
HP Switch# display stp root
HP Switch#
Example of Related ProVision Software Command Output.
HP Switch# show spanning-tree instance 11
MST Instance Information
Instance ID : 11
Mapped VLANs : 111,300
Switch Priority : 32768
Topology Change Count : 2
Time Since Last Change : 4 mins
Regional Root MAC Address : 1cc1de-cfbc80
Regional Root Priority : 32768
Regional Root Path Cost : 400000
Regional Root Port : This switch is root
Remaining Hops : 20
Designated
Port Type Cost Priority Role
State
Bridge
---- ----- ---- --------- --------------------1 10/100TX 200000 128
Root
Forwarding 1cc1de-cfbc80
2 10/100TX 200000 128
Designated Forwarding 1cc1de-02a700
3 10/100TX Auto
112
Designated Forwarding 1cc1de-02a700
4 10/100TX Auto
128
Disabled
Disabled
For more information, see the latest Advanced Traffic Management Guide for your switch.
display stp root 297
display switchover state
Comware
Related ProVision
display switchover state
show redundancy
Displays the backup state of the specified main board. This command displays the backup state
on the AMB or the standby main board (SMB) depending on the slot number specified. The backup
state of the AMB is displayed if no slot number is specified.
HP Switch-8200# display switchover state
Master HA state to slot [0] : Relative backup to slave
HP Switch-8200# display switchover state slot 0
Slave HA State: Receiving realtime data
HP Switch-8200# display switchover state slot 1
Master HA State to Slot [0]: Relative backup to slave
HP Switch-3800# display switchover state
Comware: The corresponding ProVision command is "show redundancy".
Field Descriptions
Master HA State to Slot: Backup state between the active main board (AMB) and the standby main
board (SMB).
Slave HA State: Indicates that the output information is generated by the SMB and describes the
switchover state of the SMB.
Operating Notes
In Comware, either 0 or 1 displays for the slot, depending on which board is active (master or
slave).
For more information about redundancy, see the "Chassis Redundancy (8200zl Switches)" chapter
in the latest Management and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show redundancy
Settings
-------Mgmt Redundancy : Nonstop switching enabled
Rapid Switchover Stale Timer : 0
Statistics
---------Failovers : 0
Last Failover :
Slot
---MM1
MM2
FM1
FM2
Module Description
---------------------------------------HP J9092A Management Module 8200zl
HP J9092A Management Module 8200zl
HP J9093A Fabric Module 8200zl
HP J9093A Fabric Module 8200zl
298 Display Commands
Status
-------Active
Standby
Enabled
Enabled
SW Version
-----------K.15.01.000x
K.15.01.000x
Boot Image
---------Primary
Primary
display switchover state Field Mappings.
Comware
ProVision Software
Master HA State to Slot
Status
Slave HA State
Status
display switchover state 299
display system-failure
Comware
Related ProVision
display system-failure
show boot-history
HP Switch# display system-failure
System failure handling method: reboot
Example of Related ProVision Software Command Output.
HP Switch# show boot-history
Mgmt Module 1 -- Saved Crash Information (most recent first):
=============================================================
Mgmt Module 1 in Active Mode went down: 11/07/09 14:48:36
Operator warm reload from CONSOLE session.
Mgmt Module 1 in Active Mode went down: 11/07/09 11:43:10
Operator cold reboot from CONSOLE session.
Mgmt Module 2 -- Saved Crash Information (most recent first):
=============================================================
No Saved Crash Information
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
300 Display Commands
display this
Comware
Related ProVision
display this
No equivalent ProVision software command
Displays valid configuration information under the current view. Use this command to check whether
your configuration has taken effect. Valid configuration that is the same as the default is not
displayed. Invalid configuration is not displayed. Execution of this command in any user interface
view displays the valid configuration in all the user interfaces. Execution of this command in any
VLAN view displays the configurations of all the created VLANs.
HP Switch# display this
vlan 1
name "DEFAULT_VLAN"
no untagged 1-2,48
untagged 3-47
ip address dhcp-bootp
exit
vlan 10
name "VLAN10"
untagged 1,48
ip address 10.10.10.3 255.255.255.0
ip igmp
exit
vlan 30
name "VLAN30"
untagged 2
ip address 30.30.30.2 255.255.255.0
ip igmp
ip rip 30.30.30.2
ip pim-sparse
ip-addr any
exit
exit
Minimum Software Version: 15.10.
display this 301
display transceiver alarm interface
Comware
Related ProVision
display transceiver alarm interface
show interface transceiver detail
Displays the current alarm information of a single or all transceivers.
HP Switch(config)# display transceiver alarm interface g1
G1 transceiver current alarm information:
Rx power low
Field Descriptions
RX loss of signal: Incoming (RX) signal is lost.
TX fault: Transmit (TX) fault
RX power high: Incoming (RX) power level is high.
RX power low: Incoming (RX) power level is low.
TX power high: TX power is high.
TX power low: TX power is low.
TX bias low: TX bias current is low. TX bias high: TX bias current is high.
Temp high: Temperature is high.
Temp low: Temperature is low.
Voltage high: Voltage is high.
Voltage low: Voltage is low.
Transceiver info I/O error: Transceiver information read and write error
Transceiver info checksum error: Transceiver information checksum error
Transceiver type and port configuration mismatch: Transceiver type does not match port
configuration.
Transceiver type not supported by port hardware: Transceiver type is not supported on the port.
RX loss of signal: Incoming (RX) signal is lost.
RX not ready: RX is not ready
RX CDR loss of lock: RX clock cannot be recovered.
TX fault: TX fault
TX not ready: TX is not ready
TX CDR loss of lock: TX clock cannot be recovered.
Module not ready: Module is not ready.
APD supply fault: APD (Avalanche Photo Diode) supply fault
TEC fault: TEC (Thermoelectric Cooler) fault
Wavelength unlocked: Wavelength of optical signal exceeds the manufacturer's tolerance.
RX power high: RX power is high.
RX power low: RX power is low.
TX power high: TX power is high.
TX power low: TX power is low.
TX bias high: TX bias current is high.
TX bias low: TX bias current is low.
302 Display Commands
Temp high: Temperature is high.
Temp low: Temperature is low.
Voltage high: Voltage is high.
Voltage low: Voltage is low.
Transceiver info I/O error: Transceiver information read and write error
Transceiver info checksum error: Transceiver information checksum error
Transceiver type and port configuration mismatch: Transceiver type does not match port
configuration.
Transceiver type not supported by port hardware: Transceiver type is not supported on the port.
Operating Notes
Possible values for HPN and H3C alarms/errors are not the same.
The following alarms/errors are not supported in H3C devices, and they will be displayed in HPN
output, if present:
•
WIS local fault
•
Receive optical power fault
•
PMA/PMD receiver local fault
•
PMA/PMD transmitter local fault
•
PCS receive local fault
•
PCS transmit local fault
•
PHY XS receive local fault
•
Laser bias current fault
•
Laser temperature fault
•
Laser output power fault
HPN does not support the following alarms/errors, and they are not displayed in the display
command output:
•
RX not ready
•
RX CDR loss of lock
•
TX not ready
•
TX CDR loss of lock
•
Module not ready
•
APD supply fault
•
TEC fault
•
Wavelength unlocked
The following values are supported on both HPN and H3C devices:
•
Temp high
•
Temp low
•
Voltage high
•
Voltage low
•
TX bias high
•
TX bias low
display transceiver alarm interface 303
•
TX power high
•
TX power low
•
RX power high
•
RX power low
•
Transceiver info I/O error
•
Transceiver info checksum error
•
Transceiver type and port configuration mismatch
•
Transceiver type not supported by port hardware
•
RX loss of signal
•
TX fault
For more information on transceivers, see the "Troubleshooting" chapter in the latest Management
and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# show interfaces transceiver 23 detail
Transceiver in 23
Interface Index
Type
Model
Connector type
Wavelength
Transfer distance
Diagnostic support
Serial number
Status
Temperature
TX Bias
TX Power
RX Power
:
:
:
:
:
:
:
:
:
:
:
:
24
10GbE-LR
J8437A
SC
Channel #0: 1310nm, #1:0nm, #2:0nm, #3:0nm
10000m (SM)
DOM
ED456SS987
32.754C
42.700mA
0.5192mW, -2.847dBm
0.0040mW, -23.979dBm
Recent Alarms:
Rx power low alarm
Rx power low warning
Recent errors:
Receive optical power fault
PMA/PMD receiver local fault
PMA/PMD transmitter local fault
PCS receive local fault
PHY XS transmit local fault
Time stamp : Mon Mar 7 16:26:06 2011
display transceiver alarm interface Field Mappings.
Comware
ProVision Software
Rx not ready
n/a
RX CDR loss of lock
n/a
TX not ready
n/a
TX CDR loss of lock
n/a
304 Display Commands
Comware
ProVision Software
Module not ready
n/a
APD supply fault
n/a
TEC fault
n/a
Wavelength unlocked
n/a
Temp high
Temp high
Temp low
Temp low
Voltage high
Voltage high
Voltage low
Voltage low
TX bias high
TX bias high
TX bias low
TX bias low
TX power high
TX power high
TX power low
TX power low
RX power high
RX power high
RX power low
RX power low
RX loss of signal
RX loss of signal
TX fault
TX fault
display transceiver alarm interface 305
display transceiver diagnosis interface
Comware
Related ProVision
display transceiver diagnosis interface
show interface transceiver [<port> | detail ]
Displays the currently measured value of digital diagnosis parameters of H3C customized
anti-spoofing pluggable optical transceivers.
HP Switch(config)# display transceiver diagnosis interface g1
G1 transceiver diagnostic information:
Current diagnostic parameters:
Temp.(C)
Voltage(V)
Bias(mA)
RX power(dBM)
TX power(dBM)
25.000
0.0000
7.864
-inf
-2.350
HP Switch(config)# display transceiver diagnosis interface g4
G4 transceiver diagnostic information:
Error: The transceiver does not support this function.
Field Descriptions
transceiver diagnostic information: Digital diagnosis information of the transceiver plugged in the
interface.
Current diagnostic parameters: Current diagnostic parameters.
Temp.(&deg;C): Digital diagnosis parameter-temperature, in &deg;C, with the precision to 1&deg;C.
Voltage(V): Digital diagnosis parameter-voltage, in V, with the precision to 0.01 V.
Bias(mA): Digital diagnosis parameter-bias current, in mA, with the precision to 0.01 mA.
RX power(dBM): Digital diagnosis parameter-RX power, in dBM, with the precision to 0.01 dBM.
TX power(dBM): Digital diagnosis parameter-TX power, in dBM, with the precision to 0.01 dBM.
Operating Notes
For more information on transceivers, see the "Troubleshooting" chapter in the latest Management
and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# sh
Transceiver in 24
Interface Index
Type
Model
Connector Type
Wavelength
Transfer Distance
Diagnostic Support
Serial Number
Status
Temperature
Voltage
Tx Bias
Tx Power
Rx Power
:
:
:
:
:
int transceiver 24 detail
:
:
:
:
:
:
:
:
124
SFP+LR
J9151A
LC
1310nm
10.0km (9um),
DOM
CN847GV009
35.148C
3.2348V
41.952mA
0.4047mW, -3.929dBm
0.0006mW, -32.218dBm
Recent Alarms :
Rx power low alarm
Rx power low warning
Recent Errors :
306 Display Commands
Rx loss of signal
Time Stamp
: Mon Jun 11 03:00:27 2012
display transceiver diagnosis interface Field Mappings.
Comware
ProVision Software
transceiver diagnostic information
Transceiver in
Current diagnostic parameters
Status
Temp. (&deg;C)
Temperature
Voltage(V)
Voltage
Bias(mA)
TX Bias
RX power(dBM)
RX Power
TX power(dBM)
TX Power
display transceiver diagnosis interface 307
display transceiver interface
Comware
Related ProVision
display transceiver interface
show interface transceiver [<port> | detail ]
Displays main parameters of a single or all pluggable transceivers.
HP Switch(config)# display transceiver interface g1
G1 transceiver information:
Transceiver Type
: 10GbE-SR
Connector Type
: SC
Wavelength(nm)
: 850nm
Transfer Distance(m)
: 300m (MM generic)
Digital Diagnostic Monitoring : YES
Vendor Name
: n/a
Ordering Name
: J8436A
Field Descriptions
transceiver information: Pluggable transceiver information
Connector Type: Type of the connectors of the transceiver:
•
Optical connectors, including SC (SC connector, developed by NTT) and LC (LC connector,
1.25 mm/RJ-45 optical connector developed by Lucent).
•
Other connectors, including RJ-45 and CX 4.
Wavelength(nm):
•
Optical transceiver: Central wavelength of the laser sent, in nm. If the transceiver supports
multiple wavelengths, every two wavelength values are separated by a comma.
•
Electrical transceiver: Displayed as N/A.
Transfer distance(xx): Transfer distance, with xx representing km for singlemode transceivers and
m for other transceivers. If the transceiver supports multiple transfer medium, every two values of
the transfer distance are separated by a comma. The corresponding transfer medium is included
in the bracket following the transfer distance value. The following are the transfer media:
•
9 um: 9/125 um single-mode fiber
•
50 um: 50/125 um multi-mode fiber
•
62.5 um: 62.5/125 um multi-mode fiber
•
TP: Twisted pair
•
CX4: CX4 cable
Digital Diagnostic Monitoring: Whether the digital diagnosis function is supported, where:
•
YES: Supported
•
NO: Not supported
Vendor Name: Vendor name or name of the vendor who customizes the transceiver:
•
H3C anti-spoofing transceiver (customized): H3C is displayed.
•
Other transceivers: The vendor name is displayed; if the vendor is unknown or illegal, unknown
is displayed.
Ordering Name:
•
H3C devices: Switch model is displayed
•
Other devices: N/A is displayed.
308 Display Commands
Operating Notes
For more information on transceivers, see the "Troubleshooting" chapter in the latest Management
and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# sh int transceiver 24 detail
Transceiver in 24
Interface Index : 124
Type : SFP+LR
Model : J9151A
Connector Type : LC
Wavelength : 1310nm
Transfer Distance : 10.0km (9um),
Diagnostic Support : DOM
Serial Number : CN847GV009
Status
Temperature : 35.148C
Voltage : 3.2348V
Tx Bias : 41.952mA
Tx Power : 0.4047mW, -3.929dBm
Rx Power : 0.0006mW, -32.218dBm
Recent Alarms :
Rx power low alarm
Rx power low warning
Recent Errors :
Rx loss of signal
Time Stamp
: Mon Jun 11 03:00:27 2012
display transceiver interface Field Mappings.
Comware
ProVision Software
transceiver information
Transceiver in <int>
Transceiver Type
Type
Connector Type
Connector type
Wavelength(nm)
Wavelength
Transfer distance (xx)
Transfer distance
Digital Diagnostic Monitoring
Diagnostic support
Vendor Name
n/a
Ordering Name
Model
display transceiver interface 309
display transceiver manuinfo interface
Comware
Related ProVision
display transceiver manuinfo interface
show interface transceiver [<port> | detail ]
Displays the transceiver manufacturing information of the specified transceiver on an interface or
of all the interfaces in the device.
HP Switch(config)# display transceiver manuinfo interface g1
G1 transceiver manufacture information:
Manu. Serial Number : MY902IF107
Manufacturing Date
: 081118
Vendor Name
: n/a
Field Descriptions
Manu. Serial Number: Serial number of the transceiver, generated during device commissioning
Manufacturing Date: Commissioning date of the transceiver, which is the date of the computer
used for commissioning the switch
Vendor Name: Name of vendor who customizes the transceiver
Operating Notes
The manufacturing date is displayed in the following formats:
•
Older transceivers—displayed in yyyymmdd format
•
Newer transceivers—displayed in yymmddll or yymmdd format.
For more information on transceivers, see the "Troubleshooting" chapter in the latest Management
and Configuration Guide for your switch.
Example of Related ProVision Software Command Output.
HP Switch(config)# sh int transceiver 24 detail
Transceiver in 24
Interface Index : 124
Type : SFP+LR
Model : J9151A
Connector Type : LC
Wavelength : 1310nm
Transfer Distance : 10.0km (9um),
Diagnostic Support : DOM
Serial Number : CN847GV009
Status
Temperature : 35.148C
Voltage : 3.2348V
Tx Bias : 41.952mA
Tx Power : 0.4047mW, -3.929dBm
Rx Power : 0.0006mW, -32.218dBm
Recent Alarms :
Rx power low alarm
Rx power low warning
Recent Errors :
Rx loss of signal
Time Stamp
310
Display Commands
: Mon Jun 11 03:00:27 2012
display transceiver diagnosis manuinfo Field Mappings.
Comware
ProVision Software
Manu. Serial Number
Serial Number
Manufacturing Date
n/a
Vendor Name
n/a
display transceiver manuinfo interface
311
display user-bind
Comware
Related ProVision
display user-bind
show ip source-lockdown bindings
Displays user bind address.
HP Switch# display user-bind
Total entries found: 1
MAC
IP
Vlan Port Status
0030c1-7f49c0
120.93.49.7
2
1
Example of Related ProVision Software Command Output.
HP Switch# show ip source-lockdown bindings
Dynamic IP Lockdown (DIPLD) Bindings
Mac Address IP Address VLAN Port Not in HW
----------- ---------- ----- ----- --------001122-334455 10.10.10.1 1111 X11
005544-332211 10.10.10.2 2222 Trk11 YES
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
312
Display Commands
display vlan
Comware
Related ProVision
display vlan
No equivalent ProVision software command
Displays vlan-id for the existing vlan only. If it is consecutive it displays as a range.
HP Switch# display vlan
Total 2 VLAN exist(s).
The following VLANs exist:
1(default), 7,
HP Switch# display vlan static
Total 2 VLAN exist(s).
The following VLANs exist:
1(default), 7,
HP Switch# display vlan 7
VLAN ID: 7
VLAN Type: static
Route Interface: n/a
Description: VLAN 0007
Name: VLAN7
Tagged Ports:
3
5
10
16
Untagged Ports:
8
11
21
22
HP Switch# display vlan 8-10
VLAN(s) do(es) not exist.
7
19
18
HP Switch# display vlan dynamic
No dynamic VLAN exists!
HP Switch# display vlan dynamic
Total 2 dynamic VLAN exist(s).
The following dynamic VLANs exist:
2, 4,
Minimum Software Version: 15.10.
display vlan
313
display vrrp
Comware
Related ProVision
display vrrp
show vrrp
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays vrrp details like VLAN, status, priority, and router ip address.
HP Switch# display vrrp
IPv4 Standby Information:
Run Mode : Standard
Run Method : Virtual MAC
Total number of virtual routers : 2
Interface
VRID
State
Run
Adver Auth
Virtual
Pri
Timer Type
IP
------------------------------------------------------------Vlan4
4
Initialize
144
1
None
14.4.1.1
Vlan4
5
Initialize
154
1
None
14.4.2.1
Field Descriptions
Run Mode: Current VRRP working mode, including:
•
Standard: Standard protocol mode
•
Load Balance: Load balancing mode
Run Method: Current VRRP running mode, including
•
Real MAC: Real MAC mode, which means the virtual IP address of the VRRP group is mapped
to the real MAC address of the interface.
•
Virtual MAC: Virtual MAC mode, which means the virtual IP address of the VRRP group is
mapped to the virtual MAC address.
Total number of virtual routers: Number of VRRP groups
Interface: Interface to which the VRRP group belongs
VRID: ID of the VRRP group
Run Pri: Running priority of the router, or in other words, the current priority of the router. With
VRRP tracking configured, when the state of the monitored interface or track entry changes, the
priority of the router changes.
Adver. Timer: VRRP advertisement interval, in seconds
Auth Type: Authentication type, including
•
None: No authentication
•
Simple: Simple text authentication
•
MD5: MD5 authentication
Virtual IP: Virtual IP address of the VRRP group
Example of Related ProVision Software Command Output.
HP Switch# show vrrp config
VRRP Global Configuration Information
314
Display Commands
VRRP Enabled : Yes
Traps Enabled : Yes
Virtual Routers Respond to Ping Requests : Yes
VRRP Nonstop Enabled: Yes
VRRP Virtual Router Configuration Information
Vlan ID : 10
Virtual Router ID : 1
Administrative Status [Disabled] : Enabled
Mode [Uninitialized] : Backup
Priority [100] : 150
Advertisement Interval [1] : 1
Preempt Mode [True] : True
Preempt delay time : 0
Respond to Virtual IP Ping Requests [Yes] : Yes
Primary IP Address : Lowest
IP Address Subnet Mask
--------------- --------------10.0.202.87
255.255.0.0
For more information, see the latest Multicast and Routing Guide for your switch.
display vrrp
315
display vrrp interface <interface-type> vrid <virtual routerid>
Comware
Related ProVision
display vrrp interface <interface-type> vrid <virtual
routerid>
show vrrp<interface-type> vrid <virtual routerid>
NOTE:
This command is not supported on the HP 2920 Series switches.
HP Switch# display vrrp interface vlan-interface 4 vrid 1
IPv4 Standby Information:
Run Mode : Standard
Run Method : Virtual MAC
Info: No such standby!
HP-E3500-24-PoE# display vrrp interface vlan-interface 4 vrid 4
IPv4 Standby Information:
Run Mode : Standard
Run Method : Virtual MAC
Interface
VRID
State
Run
Adver Auth
Virtual
Pri
Timer
Type
IP
------------------------------------------------------------Vlan4
4
Initialize
144
1
None
14.4.1.1
Example of Related ProVision Software Command Output.
HP Switch# show vrrp vlan 2 vrid 1 config
VRRP Virtual Router Configuration Information
Vlan ID : 2
Virtual Router ID : 1
Administrative Status [Disabled] : Enabled
Mode [Uninitialized] : Backup
Priority [100] : 150
Advertisement Interval [1] : 1
Preempt Mode [True] : True
Preempt delay time : 0
Respond to Virtual IP Ping Requests [Yes] : Yes
Primary IP Address : Lowest
IP Address Subnet Mask
--------------- --------------10.0.202.87 255.255.0.0
For more information, see the latest Multicast and Routing Guide for your switch.
316
Display Commands
display vrrp statistics
Comware
Related ProVision
display vrrp statistics
show vrrp statistics
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays vrrp counters like invalid type packets received, priority zero packets received and sent
on each vrrp router configured.
HP Switch# display vrrp statistics
Interface
VRID
CheckSum Errors
Invalid Type Pkts Rcvd
IP TTL Errors
Invalid Auth Type
Packet Length Errors
Become Master
Adver Rcvd
Adver Sent
:
:
:
:
:
:
:
:
:
:
Vlan-interface3
2
0
Version Errors
0
Advertisement Interval Errors
0
Auth Failures
:
n/a Auth Type Mismatch
0
Address List Errors
0
Priority Zero Pkts Rcvd
0
Priority Zero Pkts Sent
n/a
: 0
: 0
n/a
: 0
: 0
: 0
: 0
Field Descriptions
Interface: Interface to which the VRRP group belongs
VRID: Serial number of the VRRP group
CheckSum Errors: Number of packets with checksum errors
Version Errors: Number of packets with version errors
Invalid Type Pkts Rcvd: Number of packets with incorrect packet type
Advertisement Interval Errors: Number of packets with advertisement interval errors
IP TTL Errors: Number of packets with TTL errors
Auth Failures: Number of packets with authentication failures
Invalid Auth Type: Number of packets with authentication failures due to invalid authentication
types
Auth Type Mismatch: Number of packets with authentication failures due to mismatching
authentication types
Packet Length Errors: Number of packets with VRRP packet length errors
Address List Errors: Number of packets with virtual IP address list errors
Become Master: Number of times that the router worked as the master
Priority Zero Pkts Rcvd: Number of received advertisements with the priority of 0
Advertise Rcvd: Number of received advertisements
Priority Zero Pkts Sent: Number of advertisements with the priority of 0 sent
Advertise Sent: Number of advertisements sent
Example of Related ProVision Software Command Output.
HP Switch# show vrrp statistics global
VRRP Global Statistics Information
VRRP Enabled : Yes
display vrrp statistics
317
Protocol Version : 2
Invalid VRID Pkts Rx : 0
Checksum Error Pkts Rx : 0
Bad Version Pkts Rx : 0
For more information, see the the latest Multicast and Routing Guide for your switch.
318
Display Commands
display vrrp statistics interface <interface-type> vrid <virtual router-id>
Comware
Related ProVision
display vrrp statistics interface <interface-type> vrid
<virtual router-id>
show vrrp statistics global
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays statistics about VRRP group(s). If you specify both an interface and a VRRP group, only
the statistics about the specified VRRP group on the interface are displayed. If you only specify an
interface, the statistics about all the VRRP groups on the interface are displayed. If you specify
neither, the statistics about all the VRRP groups on the router are displayed.
HP Switch# display vrrp statistics interface Vlan 3
Interface
VRID
CheckSum Errors
Invalid Type Pkts Rcvd
IP TTL Errors
Invalid Auth Type
Packet Length Errors
Become Master
Adver Rcvd
Adver Sent
:
:
:
:
:
:
:
:
:
:
Vlan-interface3
2
0 Version Errors
: 0
0
Advertisement Interval Errors : 0
0
Auth Failures
: n/a
n/a Auth Type Mismatch
: 0
0
Address List Errors
: 0
0
Priority Zero Pkts Rcvd
: 0
0
Priority Zero Pkts Sent
: 0
n/a
Example of Related ProVision Software Command Output.
HP Switch# show vrrp statistics global
VRRP Global Statistics Information
VRRP Enabled : Yes
Protocol Version : 2
Invalid VRID Pkts Rx : 0
Checksum Error Pkts Rx : 0
Bad Version Pkts Rx : 0
For more information, see the latest Multicast and Routing Guide for your switch.
display vrrp statistics interface <interface-type> vrid <virtual router-id>
319
display vrrp verbose
Comware
Related ProVision
display vrrp verbose
show vrrp
NOTE:
This command is not supported on the HP 2920 Series switches.
Displays detailed state information of VRRP group(s). If you specify both an interface and a VRRP
group, only the state information of the specified VRRP group on the interface is displayed. If you
only specify an interface, the state information of all the VRRP groups on the interface is displayed.
If you specify neither, the state information of all the VRRP groups on the router is displayed.
HP Switch# display vrrp verbose
IPv4 Standby Information:
Run Mode
: Standard
Run Method
: Virtual MAC
Total number of virtual routers : 2
Interface Vlan-interface4
VRID
: 4
Adver Timer : 1
Admin Status
: UP
State
: Initialize
Config Pri
: 144 Running Pri : None
Preempt Mode
: YES Delay Time : 0
Auth Type
: None Key
:
Virtual IP
: 14.4.1.1
Virtual MAC
: 00005e-000104
Master IP
:
Interface Vlan-interface4
VRID
: 5
Adver Timer : 1
Admin Status
: UP
State
: Initialize
Config Pri
: 154 Running Pri : None
Preempt Mode
: YES Delay Time : 0
Auth Type
: None Key
:
Virtual IP
: 14.4.2.1
Virtual MAC
: 00005e-000105
Master IP
:
VRRP Track Information:
Track Interface: Port23 State : Down Pri
Reduced : n/a
Track Interface: Vlan2 State : Down Pri
Reduced : n/a
Example of Related ProVision Software Command Output.
HP Switch# show vrrp
VRRP Global Statistics Information
VRRP Enabled : Yes
Protocol Version : 2
Invalid VRID Pkts Rx : 0
Checksum Error Pkts Rx : 0
Bad Version Pkts Rx : 0
Virtual Routers Respond To Ping Requests : Yes
VRRP Virtual Router Statistics Information
Vlan ID : 2
320 Display Commands
Virtual Router ID : 1
State : Master
Up Time : 25 secs
Virtual MAC Address : 00005e-000101
Master's IP Address : 10.0.102.87
Associated IP Addr Count : 1 Near Failovers : 0
Advertise Pkts Rx : 0
Become Master : 1
Zero Priority Rx : 0
Zero Priority Tx : 0
Bad Length Pkts : 0
Bad Type Pkts : 0
Mismatched Interval Pkts : 0 Mismatched Addr List Pkts : 0
Mismatched IP TTL Pkts : 0
Mismatched Auth Type Pkts : 00
For more information, see the latest Multicast and Routing Guide for your switch.
display vrrp verbose
321
3 Fundamental Commands
backup startup-configuration
Comware
Related ProVision
backup startup-configuration
copy startup-config tftp <ip-address> <file name>
Used to backup the startup configuration file (used at the next system startup) to a specified TFTP
server and to a specified filename.
HP Switch# backup startup-configuration to 120.93.49.9 test_new
TFTP download in progress.
Related ProVision Software Command.
To upload the current startup configuration to a file named sw8200 in the config directory on drive
“d” in a TFTP server with an IP addres of 10.28.227.105, use the following command:
HP Switch# copy startup-config tftp 10.28.227.105
d:\configs\sw8200
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
322 Fundamental Commands
clock datetime
Comware
Related ProVision
clock datetime
clock set <Time[date] | Date[Time]>
Used to set the current time and date of the device. You can leave the ss field blank when you
specify the time parameters. This command accepts any input for the YYYY value. It displays the
current time once the value is set. It displays a warning string if it is executed in Manager View.
It is not available in Operator View, it is only available in Configure context.
HP Switch# clock datetime 8:8:8 7/7/7
Related ProVision Software Command.
HP Switch# clock set
Operating Notes
For more information, refer to the latest Command Line Interface Reference Guide for your switch.
Minimum Software Version: 15.10.
clock datetime 323
clock summer-time one-off
Comware
Related ProVision
clock summer-time
clock summer-time
This command does not differ from the related ProVision software command.
HP Switch# clock summer-time
Operating Notes
For more information, refer to the latest Command Line Interface Reference Guide for your switch.
Minimum Software Version: 15.10.
324 Fundamental Commands
clock summer-time repeating
Comware
Related ProVision
clock summer-time repeating
clock summer-time
This command does not differ from the related ProVision software command.
HP Switch# clock summer-time
Operating Notes
For more information, refer to the latest Command Line Interface Reference Guide for your switch.
Minimum Software Version: 15.10.
clock summer-time repeating 325
clock timezone
Comware
Related ProVision
clock timezone
clock timezone
This command does not differ from the related ProVision software command.
HP Switch# clock timezone
Operating Notes
For more information, refer to the latest Command Line Interface Reference Guide for your switch.
Minimum Software Version: 15.10.
326 Fundamental Commands
command accounting
Comware
Related ProVision
command accounting
aaa accounting commands < stop-only | interim-update > radius
Used to enable command accounting.
HP Switch# command accounting
Related ProVision Software Command.
HP Switch# aaa accounting commands
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
command accounting 327
command authorization
Comware
Related ProVision
command authorization
aaa authorization commands radius
Used to enable command authorization.
HP Switch# command authorization
Related ProVision Software Command.
HP Switch# aaa authorization commands radius
Operating Notes
For more information, refer to the latest Access Security Guide for your switch.
Minimum Software Version: 15.10.
328 Fundamental Commands
command-alias enable
Comware
Related ProVision
command-alias enable
No equivalent ProVision software command
Used to enable the command keyword alias function. By default, the command keyword alias
function is enabled.
HP Switch# command-alias enable
Minimum Software Version: 15.10.
command-alias enable 329
command-alias mapping
Comware
Related ProVision
command-alias mapping
No equivalent ProVision software command
Used to configure a command keyword alias. By default, a command keyword has no alias. By
default, the command is enabled and not configurable. It is available in Manger view. It accepts
"any string" (irrespective of whether it’s a valid command token or not). Cmdkey value range is
1-40 and AliasKey value range is 1-32.
HP Switch# command-alias mapping
Minimum Software Version: 15.10.
330 Fundamental Commands
copy
Comware
Related ProVision
copy
copy config SOURCE_CONFIG_FILE_ON_SWITCH config
DESTINATION_CONFIG_FILE_ON_SWITCH
This command does not differ from the related ProVision software command.
HP Switch# copy config SOURCE_CONFIG_FILE_ON_SWITCH config
DESTINATION_CONFIG_FILE_ON_SWITCH
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
copy
331
delete <startup-config>
Comware
Related ProVision
delete <startup-config>
erase config <file name>
Used to delete config file from the system directory. This command can be executed from any
context. The keyword 'delete' tab help text lists the config files which can be deleted. The command
allows only deletion of config files and not other files. It does not support wildcards (like *.txt) and
file names with URL’s. Deleted files cannot be restored.
HP Switch# delete config1
Related ProVision Software Command.
HP Switch# erase config
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
332 Fundamental Commands
flow-control
Comware
Related ProVision
flow-control
flow-control
This command does not differ from the related ProVision software command.
HP Switch# flow-control
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
flow-control 333
idle-timeout
Comware
Related ProVision
idle-timeout
console inactivity-timer
Used to set the idle-timeout timer. When it expires, user sessions are terminated. By default
idle-timeout is disabled. The command supports only minutes. And these minutes are the predefined
set 0,1,5,10,15,20,30,60,120. The command is available in configure context. The default
inactivity timer is 0 and means it is disabled.
HP Switch# idle-timeout 120
Related ProVision Software Command.
HP Switch# console inactivity-timer
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
334 Fundamental Commands
quit
Comware
Related ProVision
quit
exit
Used to return to a lower-level view. If the current view is operator mode, this command terminates
the current connection and quits the system.
HP Switch# quit
Do you want to log out [y/n]?
Related ProVision Software Command.
HP Switch# exit
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
quit 335
reboot
Comware
Related ProVision
reboot slot <slot num>
boot
Used to reboot a module. If the slot keyword is not provided, the whole system reboots.
HP Switch# reboot slot A
Related ProVision Software Command.
HP Switch# boot
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
336 Fundamental Commands
reset saved-configuration
Comware
Related ProVision
reset saved-configuration
erase startup
Used to delete the startup configuration file saved on the storage medium of the switch. The
command can be executed in manager mode.
Related ProVision Software Command.
HP Switch# erase startup
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
reset saved-configuration 337
restore startup-configuration
Comware
Related ProVision
restore startup-configuration
copy tftp startup-config
Used to download a configuration file from the specified TFTP server to the switch and specify the
configuration file as the startup configuration file to be used at the next startup of the switch. The
command is supported in manager mode. When you download a config file from a remote server
which has same name as current active startup config file name (but both are not identical) then
after downloading the file the switch reboots itself. In this case, the command triggers the download
of the config file from the remote server but the next startup-configuration file is not configured.
A maximum of 3 config files can be stored on the switch. There are no restrictions on the file name.
HP Switch# restore startup-configuration from 120.93.49.9
restore_test
This will change the default configuration file to be used
whenever the switch is rebooted. Continue [y/n]?
Related ProVision Software Command.
HP Switch# copy tftp startup-config
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
338 Fundamental Commands
return
Comware
Related ProVision
return
end
Used to return to user view from current view (non user view), as with the hot key ctrl+Z.
HP Switch# return
Related ProVision Software Command.
HP Switch# end
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
return 339
save
Comware
Related ProVision
save
write memory
Used to save the current configuration to the current startup config file. By default, the current
configuration gets saved in the current start-up configuration file.
Related ProVision Software Command.
HP Switch# write memory
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
340 Fundamental Commands
schedule reboot at
Comware
Related ProVision
schedule reboot at
reload at
Used to enable the scheduled reboot function of the whole system (including all cards) at a specific
time and date. The command can be executed in manager mode. The supported date form is
mm/dd[/[yy]yy]. The command cannot be executed if the date is not specified and specified reboot
time is earlier than the current time.
HP Switch# schedule reboot at 14:00 04/13/2012
Reload scheduled at 14:00:10 04/13/2012
(in 0 days, 0 hours, 49 minutes)
System will be rebooted at the scheduled time from secondary
image.
Do you want to continue [y/n]?
Related ProVision Software Command.
HP Switch# reload at 12:05 01/01/2012
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
schedule reboot at 341
schedule reboot delay
Comware
Related ProVision
schedule reboot delay
reload after
Used to enable the scheduled reboot function of the whole system (including all cards) and to set
a reboot waiting time. The command can be executed in manager mode and accepts input in
[[dd:]hh:]mm format.
HP Switch# schedule reboot delay 01:20
Reload scheduled in 0 days, 1 hours, 20 minutes
System will be rebooted at the scheduled time from secondary
image.
Do you want to continue [y/n]?
Related ProVision Software Command.
HP Switch# reload after 04:14:00
Reload scheduled in 4 days, 14 hours, 0 minutes
This command will cause a switchover at the scheduled time to
the other management module which may not be running the same
software image and configurations. Do you want to continue [y/n]?
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
342 Fundamental Commands
screen-length
Comware
Related ProVision
screen-length
terminal length
Used to set the number of lines on the next screen. This command is executed in manager mode.
The range for the number of lines supported is 2-1000.
HP Switch# screen-length
Related ProVision Software Command.
HP Switch# terminal length
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
screen-length 343
set authentication password
Comware
Related ProVision
set authentication password
set authentication password
This command does not differ from the related ProVision software command.
HP Switch# set authentication password
Operating Notes
For more information, refer to the latest Command Line Interface Reference Guide for your switch.
Minimum Software Version: 15.10.
344 Fundamental Commands
speed
Comware
Related ProVision
speed (user interface view)
console baud-rate
Used to set the transmission rate on the user interface. This command can be executed from configure
mode. There is no default value. The lowest supported value is 1200 bps. The configuration has
to be saved and the switch has to be rebooted to make the configuration effective.
HP Switch# speed 9600
This command will take effect after saving the configuration
and rebooting the system.
Related ProVision Software Command.
HP Switch# console baud-rate 19200
This command will take effect after saving the configuration
and rebooting the system.
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
speed 345
startup saved-configuration
Comware
Related ProVision
startup saved-configuration
startup-default config <config file name>
Used to specify the configuration file to be used at the next system startup. This command can be
executed in manager mode.
HP Switch# startup saved-configuration test
This will change the default configuration file to be used
whenever the switch is rebooted. Continue [y/n]?
Related ProVision Software Command.
HP Switch# startup-default secondary config config2
HP Switch# show config files
Configuration files:
id | act pri sec | name
---+-------------+----------------------------------------1 | *
*
| config1
2 |
* | config2
3 |
|
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
346 Fundamental Commands
sysname
Comware
Related ProVision
sysname <name-string>
hostname <name-string>
Used to set the name of the device. Changing device name affects the prompt of the CLI. For
example, if the device name is Sysname, the prompt of the user view is <Sysname>. Special
characters are not allowed.
HP Switch# sysname
Related ProVision Software Command.
HP Switch# hostname
Operating Notes
For more information, refer to the latest Basic Operation Guide for your switch.
Minimum Software Version: 15.10.
sysname 347
system-view
Comware
Related ProVision
system-view
configure terminal
Used to enter system view from the current user view.
HP Switch# system-view
HP Switch(config)#
Related ProVision Software Command.
HP Switch# configure terminal
HP Switch(config)#
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
348 Fundamental Commands
telnet
Comware
Related ProVision
telnet
telnet
This command does not differ from the related ProVision software command.
HP Switch# telnet
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
telnet 349
telnet ipv6
Comware
Related ProVision
telnet ipv6
telnet
Used to telnet to a remote IPv6 host. To stop the current Telnet login, press Ctrl+K or use the quit
command. This command supports both ipv6 and ipv4 formats with the given string name.
HP Switch# telnet ipv6 hostname
HP Switch# telnet ipv6 addr
Related ProVision Software Command.
HP Switch# telnet hostname
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
350 Fundamental Commands
telnet server enable
Comware
Related ProVision
telnet server enable
telnet-server
Used to enable the Telnet server. The Telnet server is enabled by default. This command is executed
in manager mode.
HP Switch# telnet server enable
Related ProVision Software Command.
HP Switch# telnet-server
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
telnet server enable
351
terminal type
Comware
Related ProVision
terminal type
console terminal
Used to configure the type of terminal display under the current user interface. By default, the
terminal display type is VT100. This command can be executed in manager mode. The configuration
becomes effective after it is saved and the system is rebooted.
HP Switch# terminal type ansi
This command will take effect after saving the configuration
and rebooting the system.
Related ProVision Software Command.
HP Switch# console terminal vt100
This command will take effect after saving the configuration
and rebooting the system.
Operating Notes
For more information, refer to the latest Basic Configuration Guide for your switch.
Minimum Software Version: 15.10.
352 Fundamental Commands
tftp
Comware
Related ProVision
tftp
copy
Used to download a specified file from the TFTP server to the local device or upload a specified
local file to the TFTP server in an IPv4 network. This command can be executed only from config
context. Downloading a file from the tftp server to any user given file or uploading any file to the
tftp server is supported only for specific type of files. Comware command allows . In ProVision this
functionality is supported only for specific type of files. The destination file parameter is mandatory.
HP Switch# tftp 120.93.49.9 put config tftp_test
TFTP download in progress.
HP Switch# tftp 120.93.49.9 get config2 tftp_test
HP Switch# tftp 120.93.49.9 sget test tftp_test
Enter manager@120.93.49.9's password:
Attempting username/password authentication...
00000K
File transfer terminated by user request.
Related ProVision Software Command.
HP Switch# copy tftp flash 10.29.227.13 flash
Device will be rebooted, do you want to continue [y/n]?
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
tftp 353
tftp ipv6
Comware
Related ProVision
tftp ipv6
copy
Used to download a specified file from a TFTP server or upload a specified local file to a TFTP
server in an IPv6 network. This command can be executed only from config context. Downloading
a file from the tftp server to any user given file or uploading any file to the tftp server is supported
only for specific type of files. Comware command allows . In ProVision this functionality is supported
only for specific type of files. The destination file parameter is mandatory.
HP Switch# tftp 120.93.49.9 put config tftp_test
TFTP download in progress.
HP Switch# tftp 120.93.49.9 get config2 tftp_test
HP Switch# tftp 120.93.49.9 sget test tftp_test
Enter manager@120.93.49.9's password:
Attempting username/password authentication...
00000K
File transfer terminated by user request.
Related ProVision Software Command.
HP Switch# copy tftp flash 10.29.227.13 flash
Device will be rebooted, do you want to continue [y/n]?
Operating Notes
For more information, refer to the latest Management and Configuration Guide for your switch.
Minimum Software Version: 15.10.
354 Fundamental Commands
undo
Comware
Related ProVision
undo
no vlan vlan-id
Used to reset the configuration of the system.
HP Switch# undo vlan vlan-id
Related ProVision Software Command.
HP Switch# no vlan vlan-id
Operating Notes
For more information, refer to the latest Command Line Interface Reference Guide for your switch.
Minimum Software Version: 15.10.
undo 355
4 Comware Configuration Help Commands
Table of Comware Commands and Associated ProVision Commands
Comware Configuration Command
ProVision Command
ProVision Command Location(s)
HP Switch(config)# acl
See ip access-list, ipv6
access-list or access-list
Access Security GuideIPv6
Configuration Guide
HP Switch(config)# acl step
Specify the index when creating the
entry
Access Security Guide
HP Switch(config)# arp check
See ip arp-mcast-replies
Multicast and Routing Guide
HP Switch(config)# arp timer
See ip arp-age
Multicast and Routing Guide
HP Switch(config)# bgp
See router bgp
Advanced Traffic Configuration Guide
HP Switch(eth-1)# bridge-aggregation
See trunk
Management and Configuration
Guide
HP Switch(eth-1)# broadcast-suppression See interface rate-limit
Management and Configuration
Guide
HP Switch(config)# classifier
See class or policy
Advanced Traffic Management Guide
HP Switch(config)# clear bgp
See clear ip bgp
Advanced Traffic Management Guide
HP Switch(config)# clear ospf
See clear ip ospf-statistics Multicast and Routing Guide
HP Switch(config)# comware-help-display When enabled, adds all the
This Guide
{enable | disable}
Comware help commands that will
help navigate and configure the
commands on a Provision switch. This
feature is disabled by default and
Comware help commands are not
available.
HP Switch(eth-1)# dhcp
See dhcp-relay or vlan <vid> Multicast and Routing Guide
ip helper-address
HP Switch(config)# dhcp-snooping
In ProVision, DHCP snooping is
applied per VLAN
Access Security Guide
HP Switch(config)# display device
See show modules
Management and Configuration
Guide
HP Switch(config)# display device
manuinfo
See show modules
Management and Configuration
Guide
HP Switch(config)# display device
manuinfo slot
See show modules
Management and Configuration
Guide
HP Switch(config)# display device
manuinfo slot <slot-num>
See show modules
Management and Configuration
Guide
HP Switch(config)# display power
See show system power-supply Management and Configuration
Guide
HP Switch(config)# display switchover
state
See show redundancy
Management and Configuration
Guide
HP Switch(config)# dns
See ip dns
Management and Configuration
Guide
HP Switch(eth-1)# dot1x
See aaa port-access
mac-based
Access Security Guide
356 Comware Configuration Help Commands
Comware Configuration Command
ProVision Command
ProVision Command Location(s)
HP Switch(eth-1)# dot1x
See aaa port-access
authenticator
Access Security Guide
HP Switch(config)# fips
See secure mode
Access Security Guide
HP Switch(config)# hwtacacs
See tacacs-server
Access Security Guide
HP Switch(vlan-1)# igmp
See vlan <vid> ip
igmpComware supports L3 IGMP
(snooping and routing) in interface
VLAN context and L2 IGMP
(snooping) in VLAN context.
ProVision IGMP in VLAN context is
similar to Comware’s L3 IGMP.
Multicast and Routing Guide
HP Switch(config)# igmp-snooping
See vlan <vid> ip igmp
Multicast and Routing Guide
HP Switch(vlan-1)# igmp-snooping
See vlan <vid> ip igmp
Multicast and Routing Guide
HP Switch(config)# interface
ProVision uses just the port number
Management and Configuration
rather than the “number, sub-number” Guide
Comware format
HP Switch(config)# ip access-list logging See ip access-list <acl>
logging
Management and Configuration
Guide
HP Switch(config)# ip policy-based-route See class or policy
Advanced Traffic Configuration Guide
HP Switch(config)# ip redirects
See ip icmp redirect
Multicast and Routing Guide?
HP Switch(config)# ip unreachables
See ip icmp unreachable
Multicast and Routing Guide?
HP Switch(config)# ipv6 access-list
logging
See ipv6 access-list <acl>
logging
Management and Configuration
Guide
HP Switch(config)# ipv6 mtu
See ipv6 jumbo ip or tunnel
mtuApplies to both IPv4 and IPv6
IPv6 Configuration Guide
HP Switch(config)# link-aggregation
See trunk
Management and Configuration
Guide
HP Switch(config)# loopback-detection
See loop protect
Advanced Traffic Management Guide
HP Switch(config)# mac-authentication
See aaa port-access
mac-based
Access Security Guide
HP Switch(config)# mld
See vlan <vid> ipv6 mld
IPv6 Configuration Guide
HP Switch(vlan-1)# mld
See vlan <vid> ip mld
IPv6 Configuration Guide
HP Switch(config)# mld-snooping
See vlan <vid> ipv6 mld
IPv6 Configuration Guide
HP Switch(vlan-1)# mld-snooping
See vlan <vid> ip mld
IPv6 Configuration Guide
HP Switch(config)# multicast
See ip multicast
Multicast and Routing Guide
HP Switch(config)# ospf
See router ospfOSPF is enabled Multicast and Routing Guide
on a VLAN, not a network. In VLAN
context, use ip ospf. Process IDs
are not supported.
HP Switch(config)# ospfv3
see router ospf3
IPv6 Configuration Guide
HP Switch(eth-1)# packet-filter
See ip vlan or ip
access-group
Access Security GuideAdvanced
Traffic Management Guide
HP Switch(config)# pim
See router pim
Multicast and Routing Guide
HP Switch(config)# poe-profile
See power-over-ethernet
Management and Configuration
Guide
Table of Comware Commands and Associated ProVision Commands 357
Comware Configuration Command
ProVision Command
ProVision Command Location(s)
HP Switch(config)# policy-based-route
See class or policy
Advanced Traffic Management Guide
HP Switch(eth-1)# proxy-arp
See ip proxy-arp
Multicast and Routing Guide
HP Switch(config)# qos apply
See class or policy
Advanced Traffic Management Guide
HP Switch(config)# qos policy
See class or policy
Advanced Traffic Management Guide
HP Switch(config)# radius server
RADIUS configuration is executed at Access Security Guide
the global level with the
radius-server command. A
global key can be specified that is
used by all servers, or individual keys
(shared secrets) can be specified for
individual servers.
HP Switch(config)# reset
See clear stat
Management and Configuration
Guide
HP Switch(config)# reset arp
See clear arp or clear ipv6
neighbors
Multicast and Routing GuideIPv6
Configuration Guide
HP Switch(config)# rip
See router rip
Multicast and Routing Guide
HP Switch(config)# route-policy
See route-mapProvision’s set action Multicast and Routing Guide
is the same as Comware’s apply
action.
HP Switch(config)# router bgp preference See router bgp distance
Advanced Traffic Configuration Guide
HP Switch(config)# router ospf area
Areas are applied in VLAN context
Multicast and Routing Guide
HP Switch(config)# router ospf
graceful-restart
See router ospf nonstop
Multicast and Routing Guide
HP Switch(config)# router ospf
preference
See router ospf distance
Multicast and Routing Guide
HP Switch(config)# router ospf3
preference
See router ospf3 distance
IPv6 Configuration Guide
HP Switch(config)# router pim ipv6
See router pim ipv6ProVision
supports MLD and IPv6 unicast
routing, but IPv6 addressing is not
supported by PIM-DM or PIM-SM.
Multicast and Routing Guide
HP Switch(config)# router rip preference See router rip distance
Multicast and Routing Guide
HP Switch(config)# router-id
See ip router-id
Multicast and Routing Guide
HP Switch(eth-1)# shutdown
See disable
Management and Configuration
Guide
HP Switch(config)# snmp-agent
See snmp-server
Management and Configuration
Guide
HP Switch(config)# spanning-tree active See spanning-tree
pending-apply
Advanced Traffic Management Guide
HP Switch(config)# spanning-tree
compliance
See spanning-tree
legacy-mode
Advanced Traffic Management Guide
HP Switch(config)# spanning-tree
edged-port
See spanning-tree admin-edge Advanced Traffic Management Guide
HP Switch(config)# spanning-tree mode
See spanning-tree
legacy-mode
Advanced Traffic Management Guide
HP Switch(config)# spanning-tree
region-name
See spanning-tree
config-name
Advanced Traffic Management Guide
358 Comware Configuration Help Commands
Comware Configuration Command
ProVision Command
ProVision Command Location(s)
HP Switch(config)# spanning-tree
root-protection
See spanning-tree root-guard Advanced Traffic Management Guide
HP Switch(config)# spanning-tree
tc-protection
See spanning-tree
tc-end-guard
Advanced Traffic Management Guide
HP Switch(config)# stp
See spanning-tree
Advanced Traffic Management Guide
HP Switch(config)# system-view help
Use the command comware-help This Guide
for more information about
differences between ProVision and
Comware commands and concepts.
You can also use
comware-help-display for
additional comware-specific help.
HP Switch(config)# trunk load-sharing
See trunk load-balance
Management and Configuration
Guide
HP Switch(config)# udp-helper
See ip udp-bcast-forward
Multicast and Routing Guide
HP Switch(vlan-1)# udp-helper
See ip forward-protocol udp Multicast and Routing Guide
HP Switch(config)# undo
Use no
Basic Operation Guide
HP Switch(eth-1)# vlan-interface
See vlan
Advanced Traffic Management Guide
HP Switch(eth-1)# voice
See vlan <vid> voice
Management and Configuration
Guide
HP Switch(vlan-1)# voice
ProVision designates a single VLAN
as the voice VLAN, whereas
Comware allows voice VLAN
configuration per port.
Management and Configuration
Guide
Using the Comware-Help Command
Logging In and Usernames
The two default user names for a ProVision switch are operator and manager. By default ProVision
switches do not have passwords assigned to those logins. To set a password on a ProVision switch,
issue the command password operator or password manager.
The prompt for an operator session is always terminated by a '>':
HP Switch>
The prompt for a manager session is always terminated by a '#':
HP Switch#
To move from the operator prompt to the manager prompt, issue the enable command at the
operator prompt.
To exit any context, issue the exit command.
To enable configuration of the switch, issue the configure command from the manager prompt.
The prompt will be terminated with '(config)#':
HP Switch(config)#
Serial consoles by default are 9600, N, 8, 1 but Auto Baud Detect is supported on most ProVision
switches. Auto Baud Detect is only enabled after the switch has completely booted. If your terminal
session is not sent to 9600, N, 8, 1 no boot-up messages will be displayed.
Using the Comware-Help Command 359
Enabling SSH
To enable SSH connectivity to your ProVision switch, issue the ip ssh command. If SSH has never
been enabled on the ProVision switch, you may also need to issue the crypto key generate
ssh command before issuing the ip ssh command. To disable the TELNET server on the ProVision
switch, issue the no telnet-server command.
Ports and VLANs
On ProVision, fixed-port Ethernet ports on the front of the switch are assigned a number. For
example, the 10/100/1000 copper ports of an 3500-24 would be numbered 1-24. To configure
properties of a port, you must enter that ports context by issuing the interface <port> command.
For example, to change the speed of port 10 to 100/half-duplex, and then disable it, issue the
following commands:
HP Switch> enable
HP Switch# configure
HP Switch(config)# interface 10
HP Switch(eth-10)# disable
On ProVision, modular Ethernet ports are addressed by their module letter and port number. For
example, to enter the configuration context for Port 1 on Module C of an HP 8212, you would
issue the command interface c1.
On most Comware switches, Ethernet ports can either be in "switched-L2" mode ("port link-mode
bridge") or "routed-L3" mode ( "port link-mode route"). Currently, ProVision only supports Ethernet
ports in a switched-L2 mode. By default, all ports are placed untagged in VLAN 1. To assign port
2 as an untagged member of VLAN 2, a tagged member of VLAN 3, and assign an IP address
of 3.3.3.3 to VLAN 3, issue the following commands:
HP Switch> en
HP Switch# configure
HP Switch(config)# vlan 2
HP Switch(vlan-2)# untagged 2
HP Switch(vlan-2)# vlan 3
HP Switch(vlan-3)# tagged 2
HP Switch(vlan-3)# vlan 3
HP Switch(vlan-3)# ip address 3.3.3.3/24
NOTE: All ports must at all times belong to a VLAN. Layer-3 configuration of physical ports is
always done in the VLAN context.
The command comware-help-display {enable|disable} adds all the Comware help
commands that will help a Comware user navigate and configure the commands on a Provision
switch. This feature is disabled by default and Comware help commands will not be available. All
the tab help for commands added for Comware help will start with "[comware]" prefixed to them.
Executing these commands displays some brief help text that guides configuration of the feature
on a Provision switch.
360 Comware Configuration Help Commands
Index
A
aaa accounting commands, 327, 328
aaa port-access authenticator, 357
aaa port-access mac-based, 356, 357
access-list, 356
acl, 356
acl step, 356
alias, show, 28
arp check, 356
arp detection statistics, display, 23
arp detection statistics, show, 23
arp ip-address, display, 24
arp time, 356
B
backup startup-configuration, 322
BGP, 108, 111
bgp, 356
boot set-default flash, 25
boot system, 25
boot-history, show, 300
boot-loader, display, 25
bridge-aggregation, 356
broadcast-suppression, 356
C
class, 356, 357, 358
classifier, 356
clear arp, 358
clear bgp, 356
clear ip bgp, 356
clear ip ospf-statistics, 356
clear Ipv6 neighbors, 358
clear ospf, 356
clear stat, 358
CLI context levels, 16
CLI prompts, 16
clock datetime, 323
clock summer-time one-off, 324
clock summer-time repeating, 325
clock timezone, 326
clock, display, 27
command accounting, 327
command authorization, 328
command-alias enable, 329
command-alias mapping, 330
command-alias, display, 28
commands, listing, 17
Comware software, 14
HPN switches, 14
comware-help, 356, 359
comware-help-display {enable | disable}, 356
config, show, 264
Context level, 16
copy, 331
counters rate, display, 31
cpu, show, 32
cpu-usage history, display, 33
cpu-usage, display, 32
crypto host-public-key, show, 250
current-configuration configuration, display, 36
current-configuration, display, 84
D
debug, show, 39
debugging, display, 39
default-configuration, display, 41
delete, 332
dhcp, 356
dhcp relay information all, display, 43
dhcp relay information interface Vlan-interface <vlan-id>,
display, 44
dhcp-relay, 356
dhcp-snooping, 356
dhcp-snooping information, display;, 51
dhcp-snooping packet statistics, display, 52
diagnostic-information, display, 54
disable, 358
display acl | name >, 18
display arp, 21
display command listing, 14
display device, 356
display device manuinfo, 356
display device manuinfo slot, 356
display fib, 74
display ipv6 fib, 120, 122, 124
display ipv6 neighbors all, 124
display local-proxy-arp, 151
display power, 356
display proxy-arp, 249
display switchover state, 356
dns, 356
dns domain dynamic, display, 57, 58
dns, display, 55
documentation
latest versions, 13
release notes, 13
domain name, 55
dot1x, 356, 357
dot1x sessions, display, 61
dot1x statistics, display, 61
dot1x, display, 61
E
empty output, 17
erase config, 330, 332
event log
Event Log Message Reference Guide, 13
F
field mappings, 16
361
fields, not populated, 16
fips, 357
flash, show, 25
flow-control, 333
G
gvrp status, display, 81
gvrp vlan-operation interface interface-type
interface-number, display, 82
gvrp, show, 81
H
history, show, 83
history-command, display, 83
HP Networking
switch documentation, 13
hwtacacs, 357
I
idle-timeout, 334
igmp, 357
igmp group interface vlan-interface <vlan-id> verbose,
display, 89
igmp group verbose, display, 93
igmp group x.x.x.x verbose, display, 95
igmp group, display, 86
igmp interface verbose, display, 98
igmp-snooping, 357
int, show, 31
interface, 357
interface command, 81
interface rate-limit, 356
interface, display, 102
interface, show, 102
ip
as-path, display, 108
aspath-list, show, 108
community-list, display, 111
community-list, show, 111
dns, show, 55
igmp group, show, 86
igmp groups, show, 86
ospf interface, show, 191
ospf virtual-link, show, 198
ospf, show, 197
ip access-list, 356
ip access-list <acl> logging, 357
ip access-list logging, 357
ip arp-age, 356
ip arp-mcast-replies, 356
ip dns, 356
ip forward-protocol upd, 359
ip host-public-key, show, 250
ip http, display, 112
ip https, display, 113
ip icmp redirect, 357
ip icmp unreachable, 357
ip ip-prefix, display
ip prefix-list, show, 114
362 Index
ip multicast, 357
ip ospf, show, 200
ip policy-based-route, 357
ip proxy-arp, 358
ip redirects, 357
ip router-id, 358
ip source-lockdown bindings, show, 312
ip ssh, show, 277, 280, 281
ip udp-bcast-forward, 359
ip unreachables, 357
ip vlan; ip access-group, 357
ip, show, 55
ipv6 access-list, 356
ipv6 access-list <acl> logging, 357
ipv6 access-list logging, 357
ipv6 jumbo ip, 357
ipv6 mld, show, 164
ipv6 mtu, 357
ipv6 ospf3 virtual-link, show, 220
ipv6 route, show, 126, 128, 130
ipv6 routing-table ipv6-address, display, 128
ipv6 routing-table protocol, display, 130
ipv6 routing-table, display, 126
L
lacp local, show, 131
lacp system-id, display, 131
latest manual set, 17
link, manual set, 17
link-aggregation, 357
link-aggregation, display, 133
listing commands, 17
lldp status interface interface-type interface number,
display, 149
load-balancing, 133
logfile buffer, display, 152
logging, debug, 39
logging, show, 152
loop protect, 357
loopback-detection, 357
M
mac-address multicast, display, 157
mac-authentication, 357
mac-authentication, display, 161
manual set, link, 17
memory, display, 163
mld, 357
mld group port-info, display, 169
mld group, display, 164
mld routing-table, display, 180
multicast, 357
multicast forwarding-table, display, 183
multicast routing-table, display, 184
multicast rpf-info, display, 188
N
no, 359
O
ospf, 357
ospf interface, display, 191
ospf routing, display, 197
ospf vlink, display, 198
ospfv3, 357
ospfv3 lsdb statistics, display, 210
ospfv3 lsdb, display, 208
ospfv3 peer statistics, display, 215
ospfv3 vlink, display, 220
ospfv3, display, 200
output differences, 16
output, empty, 17
P
packet-filter, 357
pim, 357
pim control-message counters, display, 224
pim grafts, display, 225
pim join-prune, display, 230
pim routing-table, display, 235
pim rp-info, display, 236
poe device, display, 237
poe interface power, display, 240
poe interface, display, 238
poe power-usage, display, 242
poe-power alarm, display, 243
poe-power switch state, display, 244
poe-profile, 357
policy, 356, 357, 358
policy-based-route, 358
port trunk, display, 245
port trunking, 133
power-over-ethernet, 357
power-over-ethernet brief, show, 237, 238, 240, 242
prompts, CLI, 16
protocol-vlan interface, display, 248
protocol-vlan, display, 247
ProVision Software, 14
ProVision software
Comware support, 14
HPN switches, 14
proxy-arp, 358
public-key local rsa public, display, 250
Q
qos apply, 358
qos policy, 358
quit, 335
R
radius server, 358
reboot, 336
reload, 25
reload , show, 265
reset, 358
reset arp, 358
restore startup-configuration, 338
return, 339
rip, 358
rip process-id interface-type interface-number, display, 257
rmon statistics, display, 261
rmon statistics, show, 261
route-map, 358
route-policy, 358
router bgp, 356
router bgp distance, 358
router bgp preference, 358
router ospf, 357
router ospf area, 358
router ospf distance, 358
router ospf graceful-restart, 358
router ospf nonstop, 358
router ospf preference, 358
router ospf3, 357
router ospf3 distance, 358
router ospf3 preference, 358
router pim, 357
router pim ipv6, 358
router rip, 358
router rip distance, 358
router rip preference, 358
router-id, 358
S
save, 340
saved-configuration by-linenum, display, 264
schedule reboot at, 341
schedule reboot delay, 342
schedule reboot, display, 265
screen-length, 343
secure mode, 357
set authentication password, 344
show access-list, 18
show arp, 21
show ip, 151, 249
show ip route, 74
show ipv6 neighbors, 124
show ipv6 route, 120, 122
show modules, 356
show redundancy, 356
show system power-supply, 356
shutdown, 358
snmp-agent, 358
snmp-agent community, display, 267
snmp-agent group, display, 268
snmp-agent local-engineid, display, 270
snmp-agent mib-view, display, 271, 272
snmp-agent sys-info, display, 273
snmp-agent trap-list, display, 274
snmp-agent usm-user, display, 275
snmp-server, 358
snmp-server traps, show, 274
snmpv3 community, show, 267
snmpv3 engineid, show, 270
snmpv3 group, show, 268, 271
snmpv3 user, show, 275
spanning-tree, 359
363
spanning-tree active, 358
spanning-tree admin-edge, 358
spanning-tree compliance; spanning-tree legacy-mode,
358
spanning-tree config-name, 358
spanning-tree edged-port, 358
spanning-tree legacy-mode, 358
spanning-tree mode, 358
spanning-tree pending-apply, 358
spanning-tree region-name, 358
spanning-tree root-guard, 359
spanning-tree root-protection, 359
spanning-tree tc-end-guard, 359
spanning-tree tc-protection, 359
speed, 345
ssh server session, display, 277
ssh server-info, display, 279
ssl client-policy, display, 280
ssl server-policy, display, 281
startup saved-configuration, 346
startup, display, 283
stp, 359
stp history, display, 294
sysname, 347
system information, show, 163, 273
system power-supply, show, 243
system, show, 27
system-failure, display, 300
system-view, 348
system-view help, 359
T
Tab key, 17
tacacs, show, 84
tacacs-server, 357
tech, show, 54
telnet, 349
telnet ipv6, 350
telnet server enable, 351
terminal type, 352
tftp, 353
tftp ipv6, 354
this, display, 301
time, 27
time, show, 27
trunk, 356, 357
trunk load-balance, 359
trunk load-sharing, 359
trunking, port, 133
trunks load-balance interface, show, 133
tunnel mtu, 357
U
udp-helper, 359
undo, 355, 359
user-bind, display, 312
V
vlan, 359
364 Index
vlan <vid. ipv6 mld, 357
vlan <vid> ip helper address, 356
vlan <vid> ip igmp, 357
vlan <vid> ipv6 mld, 357
vlan <vid> voice, 359
vlan, display, 313
vlan-interface, 359
vlan<vid> ip igmp, 357
voice, 359
W
warranty, 2