Job Information
Type
Project Name
ALRS401
Location
4" LED Flat Frame Recessed Luminaire for Square
Trims, NON-IC
Recessed Lighting
Date
Quantity
Contact/Phone
Notes
Features
Mounting Frame
The enclosed quick disconnect allows
for easy installation of the LED engine
and reflector.
for easy maintenance, the LED driver
features a power factor larger than 0.9,
and THD of less than 30%. Provided
with an integral thermal protection to
sense over temperature or improper
installation. 120V, 60Hz.
Junction Box
Optics
LED Driver Upgrade Options
Listed for through branch circuit wiring.
Maximum eight no. 12 AWG 90°C
branch-circuit conductions (four in and
four out). Ten 1/2" knockouts with true
pry-out slots and eight knockouts with
Romex® cable clamp. Ground wire is
provided on J-Box.
Diffuse lens mask the LED from direct
view.
2-Wire Lutron®: Compatible with forward
phase control technology, for use with
Lutron forward phase controls (neutral
wire required). 120V only, 50/60Hz, 40W
max.
3-Wire Lutron®: Compatible with
standard 3 wire line voltage phasecontrol technology for consistent
dimming performance and compatibility
with all Lutron 3 wire fluorescent
controls. Suitable for integration into a
planned or existing EcoSystem lighting
control solution. 120V, 50/60Hz, 40W
max.
detected), attached to the junction box.
Constructed of 22ga galvanized steel for
optimum rigidity. The frame includes a
mounting ring that accommodates up to
1-1/4" (32mm) ceiling thickness. Hanger
bars installed on short side.
Hanger Bars
Rigid male/female design allows hanger
bars to open to a maximum of 25"
(635mm). Using the provided score
lines, hanger bars can be shortened
to accommodate space constrictions.
Built-in line-up foot allows for accurate
housing height during installation. Preinstalled double-headed nail provides
easy removal of housing. Integrated
T-bar clips easily snap onto T-bars.
Optional vertical adjustable architectural
frame bracket that accepts C-channel
and EMT conduit is also included.
Quick Disconnect
LED Characteristics
Available with high powered 15W or 24W
CREE® LED chip that maintains uniform
intensity with a maximum luminous
flux of 1524; with a typical 85 CRI and
a 35,000 hour life span. Available in
3000°K or 4000°K nominal colour
temperature.
Dimming
This fixture is dimmable when used
with 0-10V for 15-24W at 120V (Consult
factory for compatible dimmers).
Environment
For indoor use only. Suitable for use in
damp locations.
Heat Sink
Description
This fixture is a 4" LED luminaire with
flat frame for use with square trims,
combining high power LED with
dimmable driver options. The luminaire
reduces operating costs and provides
maintenance-free operation. Trim sold
separately.
Constructed of extruded aluminum
designed to facilitate heat dissipation
and reduce LED junction temperature.
Adjustable heat sink mounting plate
height.
System Protection
Integral thermal protector (RP1B thermal
coupler, will disconnect if insulation is
LED Driver
Mounted on the junction box to allow
7-7/8"
200mm
6"
152mm
4-1/2"
114mm
12-3/8"
314mm
Ordering Guide
Wattage
Notes: For additional options please consult
your A-Line Lighting representative. All
trademarks are the property of their respective
owners. Due to our continued efforts to
improve our products, product specifications
are subject to change without notice.
Compatible Trims
Colour Temp.
Beam Spread
ALRS401 -
Driver Option
ATS402
4" Square reflector
14 : 15W
26 : 24W
30 : 3000°K
40 : 4000°K
W : Wide Beam Spread
Leave blank for standard 120V Driver
Ø : 0 - 10V Dimming
L : Lutron Hi-Lume ® A-Series (3 Wire)
E : Lutron Hi-Lume ® A-Series (EcoSystem®)
M : Lutron Hi-Lume ® A-Series (2 Wire)
3 : 347V Magnetic Stepdown
3E : 347V Electronic Primary
CUST : Custom
Example: ALRS401-1440W
For other voltage options, contact your Liteline representative.
Liteline Corporation
Info@ liteline.com
8 Abacus Road, Brampton
www.liteline.com
Ontario, Canada L6T 5B7
© Copyright 2015, Liteline Corporation
416-996-1856
1-866-730-7704
905-794-1990
1-888-738-9736
REV12/3.27.15