NDLED4 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
NDLED4R
Cut-Out Diameter: 5”
IMPORTANT
4
NDLED4S
Cut-Out: 5”x5”
3
2
REV
DATE
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR DESCRIPTION
FUTURE REFERENCE.
1
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable
local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY AD
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
4
3
4
2
3
REV
DESCRIPTION
2
DATE
1
MOUNTING BARS
D
D
D
4
3
2
C
C
C
C Channel-27”
Nailer Bar
13” adjustable to 24”
(provided with fixture)
C ChannelC-51”
(order Cat #: C-Chan 27)
Available upon request
(order Cat #: C-Chan 51)
Available upon request
D
13.375" REF
27.000
[685,8]
B
SCALE 0.500
1.500
[38,1]
.220
[5,59]
.220
[5,59]
1. Nailer bars are provided for use with wood joist
installations. Insert through Nailer Bar Slots in
Butterfly Brackets and secure accordingly. C-Channels
4
are optionally available, consult factory. Consult local
building codes for final support of fixture.
.201
[5,11]
(2)
QUOTATION DRAWING
11-14-12
A
.201
(2)
L I G H T I N G
[5,11]
TITLE
A
MATERIAL:
PROPERTY OF RAB LIGHTING, INCORPORATED
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
2. Remove appropriate Knock out on Junction box. Press
Clip to open the Junction Box.
3
DRAWN BY: DH
2
.250
[6,35]
SCALE
MA
THIS
DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
15154-27
C-CHANNEL
REV DATE:
3-9-12
1/2
2
REV
PROPERTY
OF RAB LIGHTING, INCORPORATED
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
SHEET:
3
1
QUOTATION DRAWING
RAB
Clip
D
L I G H T I N G
4. The fixture can be adjusted to different heights above
the ceiling surface. For height adjustment, loosen the
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
Wing Nut and slide the
ButterflyOF
Bracket.
If necessary
PROPERTY
RAB LIGHTING,
INCORPORATED
REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
remove the Wing NutANY
and
insert
screw
in different
RAB
LIGHTING,
INC. ISin
STRICTLY
PROHIBITED.
RAB CONFIDENTIAL PATENT PENDING
4
3
2
hole provided on the Butterfly Bracket.
(Fig: 2)
SCALE 0.500
SCALE 0.500
TITLE
170 LUDLOW AVE., NORTHVALE, NJ 07647
Nailer Bar Slot
13" NAILER BAR ASSEMBLY M &Male
F Connector
MATERIAL:
PART No.:
SEE NOTES
DRAWN BY: DH
15153
Fig: 1
A
DRAWING NAME:
15153 NAILER BAR ASSY
DATE:
REV DATE:
3-9-12
SCALE
FULL
SHEET:
REV
1
Wing Nut
SCALE 1.000
B
Butterfly
Bracket
Fig: 2
SCALE 0.500
DR
2
Junction Box
3. Feed the supply wires throughNOTES:
Knock out hole and
1. PART TO BE SUPPLIED BY TRIPAR INDUSTRIES
PART
NUMBER 1287
connect to the driver. See wiring
section
for details.
2. MATERIAL: GALVANIZED STEEL
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance. RAB cannot troubleshoot
Lutron systems and have provided only basic information. See
www.lutron.com for complete instructions and functional
compatibility of Lutron Drivers with Lutron or other Control systems/
dimmers.
A
DRAWING NAME:
15154-27
DATE:
4
TIT
B
27" C-CHANNEL
PART No.:
3
R
L
170 LUDLOW AVE., NORTHVALE, NJ 07647
22 GA EC STL
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
4
5. Adjust both the Butterfly Brackets such that the frame
of Rough-In Section is flush with the finished ceiling
surface. Tighten the Wing nuts.C
RAB
Knock Out
.250
[6,35]
27.000
[685,8]
Rough-in Section
(Bottom of the
Rough-in Section
to be flush with
finished ceiling)
B
Butterfly Brackets
ROUGH-IN MOUNTING
C
.500
[12,7]
B
E
D
NDLED4 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TRIM MODULE MOUNTING
1. Pull Female Connector conduit through frame opening.
Raise Trim Module towards opening and connect to
Male Connector conduit as shown in Fig. 3
2. Press Torsion Springs inward and slide Trim Module
C info frame opening. Release both springs into opening
together. Trim Ring should be flush to ceiling.
3. For the Wallwash Model, orient the fixture such that the
reflector is in correct orientation. Look for ‘Towards the
Wall’ label on the fixture.
Rough-in
Section
Male Connector
Female
Connector
WIRING
RISK OF FIRE. Universal voltage driver permits operation at
120V thru 277V, 50 or 60 Hz. For Non-Dimming, Electronic
Low Voltage (ELV) and Triac Dimming follow the wiring
directions in Fig. 4.
Trim Module
1. Connect the GROUND wire from fixture to supply ground.
Trim Ring
2. Connect the black fixture lead to the (+) LINE supply lead.
3. Connect the white fixture lead to the (-) COMMON supply B lead.
Fig: 3
Torsion Spring
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature
is cool enough to
SCALE 0.500
touch. Do not clean or maintain while fixture is energized.
Fig: 4
Lutron L3D Hi-Lume series drivers work with Lutron 3-Wire
Control (Fig. 5) or EcoSystem Digital Controls (Fig. 6).
Note: See www.lutron.com for complete instructions and functional
compatibility of Lutron drivers with Lutron or other control systems/
dimmers.
1. Do not open fixture to clean the LED. Do not touch
the LED.
2. Do not touch reflector, lens, or trim cone.
3. Do not clean any fixture surface with wood base cleaning
material such as paper towels or tissues. Only use micro
fiber cleaning cloth.
TROUBLESHOOTING
1. Check that the line voltage at the fixture is correct. Refer
to wiring directions.
Fig: 5
A
2. Is the fixture grounded properly?
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
PROPERTY
3. For questions on compatibility of dimmers purchased
OFseparately
RAB LIGHTING,
INCORPORATED
refer to www.rabweb.com
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY
RABthe
CONFIDENTIAL
PATENT
PENDING
4. If thePROHIBITED.
LED is blinking
fixture may
be overheating.
Remove the
3 Trim assembly and if the fixture is labeled
‘BLINKING LIGHT OF THIS THERMALLY PROTECTED
LUMINAIRE MAY INDICATE OVERHEATING’ allow the
fixture to cool down. Determine cause of overheating
and remove. Fixtures with this label have a thermal
protector that turns fixture off above a certain
temperature. It will automatically restart when cool.
4
Fig: 6
Easy Installation & Product Help
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
NDLED4 IN-1214
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
TOLER
.X
.XX
.XXX
ANGLE
NDLED4 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
DIMENSIONAL DRAWING
NDLED4R
10.46
10.46”
[265,7]
3.78
3.78”
[96,1]
Ø5.50
5.50”
[139,8]
11.37”
11.37
[288,8]
NDLED4S
10.46
10.46”
[265,7]
3.79
3.79”
[96,2]
5.50
5.50”
[139,7]
5.50
5.50”
[139,7]
11.37
11.37”
[288,8]
NDLED6 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
NDLED6R
Cut-Out Diameter: 7”
IMPORTANT
4
NDLED6S
Cut-Out: 7”x7”
3
2
REV
DATE
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR DESCRIPTION
FUTURE REFERENCE.
1
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable
local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY AD
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
4
3
4
2
3
REV
DESCRIPTION
2
DATE
1
MOUNTING BARS
D
D
D
4
3
2
C
C
C
C Channel-27”
Nailer Bar
13” adjustable to 24”
(provided with fixture)
C ChannelC-51”
(order Cat #: C-Chan 27)
Available upon request
(order Cat #: C-Chan 51)
Available upon request
D
13.375" REF
27.000
[685,8]
B
SCALE 0.500
1.500
[38,1]
.220
[5,59]
.220
[5,59]
1. Nailer bars are provided for use with wood joist
installations. Insert through Nailer Bar Slots in
Butterfly Brackets and secure accordingly. C-Channels
4
are optionally available, consult factory. Consult local
building codes for final support of fixture.
.201
[5,11]
(2)
QUOTATION DRAWING
11-14-12
A
.201
(2)
L I G H T I N G
[5,11]
TITLE
A
MATERIAL:
PROPERTY OF RAB LIGHTING, INCORPORATED
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
2. Remove appropriate Knock out on Junction box. Press
Clip to open the Junction Box.
3
DRAWN BY: DH
2
.250
[6,35]
SCALE
MA
THIS
DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
15154-27
C-CHANNEL
REV DATE:
3-9-12
1/2
2
REV
PROPERTY
OF RAB LIGHTING, INCORPORATED
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
SHEET:
3
1
QUOTATION DRAWING
RAB
Clip
D
L I G H T I N G
4. The fixture can be adjusted to different heights above
the ceiling surface. For height adjustment, loosen the
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
Wing Nut and slide the
ButterflyOF
Bracket.
If necessary
PROPERTY
RAB LIGHTING,
INCORPORATED
REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
remove the Wing NutANY
and
insert
screw
in different
RAB
LIGHTING,
INC. ISin
STRICTLY
PROHIBITED.
RAB CONFIDENTIAL PATENT PENDING
4
3
2
hole provided on the Butterfly Bracket.
(Fig: 2)
SCALE 0.500
SCALE 0.500
TITLE
170 LUDLOW AVE., NORTHVALE, NJ 07647
Nailer Bar Slot
13" NAILER BAR ASSEMBLY M &Male
F Connector
MATERIAL:
PART No.:
SEE NOTES
DRAWN BY: DH
15153
Fig: 1
A
DRAWING NAME:
15153 NAILER BAR ASSY
DATE:
REV DATE:
3-9-12
SCALE
FULL
SHEET:
REV
1
Wing Nut
SCALE 1.000
B
Butterfly
Bracket
Fig: 2
SCALE 0.500
DR
2
Junction Box
3. Feed the supply wires throughNOTES:
Knock out hole and
1. PART TO BE SUPPLIED BY TRIPAR INDUSTRIES
PART
NUMBER 1287
connect to the driver. See wiring
section
for details.
2. MATERIAL: GALVANIZED STEEL
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance. RAB cannot troubleshoot
Lutron systems and have provided only basic information. See
www.lutron.com for complete instructions and functional
compatibility of Lutron Drivers with Lutron or other Control systems/
dimmers.
A
DRAWING NAME:
15154-27
DATE:
4
TIT
B
27" C-CHANNEL
PART No.:
3
R
L
170 LUDLOW AVE., NORTHVALE, NJ 07647
22 GA EC STL
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
4
5. Adjust both the Butterfly Brackets such that the frame
of Rough-In Section is flush with the finished ceiling
surface. Tighten the Wing nuts.C
RAB
Knock Out
.250
[6,35]
27.000
[685,8]
Rough-in Section
(Bottom of the
Rough-in Section
to be flush with
finished ceiling)
B
Butterfly Brackets
ROUGH-IN MOUNTING
C
.500
[12,7]
B
E
D
NDLED6 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TRIM MODULE MOUNTING
1. Pull Female Connector conduit through frame opening.
Raise Trim Module towards opening and connect to
Male Connector conduit as shown in Fig. 3.
2. Press Torsion Springs inward and slide Trim Module
C info frame opening. Release both springs into opening
together. Trim Ring should be flush to ceiling.
3. For the Wallwash Model, orient the fixture such that the
reflector is in correct orientation. Look for ‘Towards the
Wall’ label on the fixture.
Rough-in
Section
Male Connector
Female
Connector
WIRING
RISK OF FIRE. Universal voltage driver permits operation at
120V thru 277V, 50 or 60 Hz. For Non-Dimming, Electronic
Low Voltage (ELV) and Triac Dimming follow the wiring
directions in Fig. 4.
Trim Module
1. Connect the GROUND wire from fixture to supply ground.
Trim Ring
2. Connect the black fixture lead to the (+) LINE supply lead.
3. Connect the white fixture lead to the (-) COMMON supply B lead.
Fig: 3
Torsion Spring
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to
SCALE
touch. Do not clean or maintain
while0.500
fixture is energized.
Fig: 4
Lutron L3D Hi-Lume series drivers work with Lutron 3-Wire
Control (Fig. 5) or EcoSystem Digital Controls (Fig. 6).
Note: See www.lutron.com for complete instructions and functional
compatibility of Lutron drivers with Lutron or other control systems/
dimmers.
1. Do not open fixture to clean the LED. Do not touch
the LED.
2. Do not touch reflector, lens, or trim cone.
3. Do not clean any fixture surface with wood base cleaning
material such as paper towels or tissues. Only use micro
fiber cleaning cloth.
TROUBLESHOOTING
1. Check that the line voltage at the fixture is correct. Refer
to wiring directions.
Fig: 5
A
2. Is the fixture grounded properly?
THIS DRAWING AND THE
IT DISCLOSES
IS THE EXCLUSIVE
3.INFORMATION
For questions
on compatibility
of dimmers purchased
PROPERTY
refer to www.rabweb.com
OFseparately
RAB LIGHTING,
INCORPORATED
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
4. If thePROHIBITED.
LED is blinking
fixture may
be overheating.
RAB LIGHTING, INC. IS STRICTLY
RABthe
CONFIDENTIAL
PATENT
PENDING
Remove the
Trim assembly and if the fixture is labeled
3
‘BLINKING LIGHT OF THIS THERMALLY PROTECTED
LUMINAIRE MAY INDICATE OVERHEATING’ allow the
fixture to cool down. Determine cause of overheating
and remove. Fixtures with this label have a thermal
protector that turns fixture off above a certain
temperature. It will automatically restart when cool.
4
Fig: 6
Easy Installation & Product Help
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
NDLED6 IN-1114
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
TOLER
.X
.XX
.XXX
ANGLE
NDLED6 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
DIMENSIONAL DRAWING
NDLED6R
12.42
12.42”
[315,4]
4.82
4.82”
[122,5]
Ø7.52
7.52”
[190,9]
13.46
13.46”
[341,9]
NDLED6S
12.63
12.63”
[320,8]
4.44
4.44”
[112,7]
13.37
7.52”
[339,6]
13.37
7.52”
[339,6]
13.37
13.37”
[339,6]
NDIC4 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
NDIC4R
Cut-Out Diameter: 5”
IMPORTANT
4
NDIC4S
Cut-Out: 5”x5”
3
2
REV
DATE
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR DESCRIPTION
FUTURE REFERENCE.
1
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable
local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY AD
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
4
3
4
2
3
REV
DESCRIPTION
2
DATE
1
MOUNTING BARS
D
D
D
C
C
C
C Channel-27”
Nailer Bar
13” adjustable to 24”
(provided with fixture)
C ChannelC-51”
(order Cat #: C-Chan 27)
Available upon request
13.375" REF
27.000
[685,8]
B
(order Cat #: C-Chan 51)
Available upon request
.500
[12,7]
B
27.000
[685,8]
B
Butterfly Brackets
ROUGH-IN MOUNTING
SCALE 0.500
1.500
[38,1]
.220
[5,59]
.220
[5,59]
1. Nailer bars are provided for use with wood joist
installations. Insert through Nailer Bar Slots in
Butterfly Brackets and secure accordingly. C-Channels
are optionally available, consult factory. Consult local
building codes for final support of fixture.
.201
[5,11]
(2)
QUOTATION DRAWING
11-14-12
A
PART No.:
DATE:
DRAWN BY: DH
2
Junction Box
Cover
SCALE
4
A
MA
THIS
DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
15154-27
C-CHANNEL
REV DATE:
3-9-12
1/2
REV
PROPERTY
OF RAB LIGHTING, INCORPORATED
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
SHEET:
3
1
RAB
SCALE 0.500
SCALE 0.500
Rough-in Section
170 LUDLOW AVE., NORTHVALE, NJ 07647
(Bottom of the
Male
Connector
13" NAILER BAR ASSEMBLY M & FRough-in Section
toAbe flush with
Fig: 1
MATERIAL:
PART No.:
DRAWING NAME:
finished ceiling)
L I G H T I N G
Nailer BarTITLE
Slot
4. The fixture can be adjusted to different heights above
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
the ceiling surface. ForPROPERTY
height adjustment,
loosen theINCORPORATED
OF RAB LIGHTING,
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
Wing Nut and slide the
Bracket.
If necessary
RAB Butterfly
LIGHTING, INC. IS STRICTLY
PROHIBITED.
RAB CONFIDENTIAL PATENT PENDING
4
3
2
remove the Wing Nut and insert in
screw in different
hole provided on the Butterfly Bracket. (Fig: 2)
SEE NOTES
DRAWN BY: DH
15153
15153 NAILER BAR ASSY
DATE:
REV DATE:
3-9-12
SCALE
FULL
SHEET:
REV
1
10.462
[265,74
6.232
[158,28
]
]
SCALE 1.000
11.475
[291,47
]
DR
2
QUOTATION DRAWING
Clip
3. Feed the supply wires throughNOTES:
Knock out hole and
1. PART TO BE SUPPLIED BY TRIPAR INDUSTRIES
PART
NUMBER 1287
connect to the driver. Re-install
Junction
Box Cover. See
2. MATERIAL: GALVANIZED STEEL
wiring section for details.
TIT
B
DRAWING NAME:
15154-27
PROPERTY OF RAB LIGHTING, INCORPORATED
3
.250
[6,35]
27" C-CHANNEL
22 GA EC STL
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
R
L
170 LUDLOW AVE., NORTHVALE, NJ 07647
MATERIAL:
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
2. Remove appropriate Knock out on Junction box. Press
Clip to remove the Junction Box Cover.
RAB NDIC4 fixtures are IC rated allowing fixtures to be
completely covered with insulation and also comply with
minimum Air Leakage requirements per the Washington State
Energy Code and Model Energy Code.
.201
(2)
L I G H T I N G
[5,11]
TITLE
A
4
5. Adjust both the Butterfly Brackets such that the frame
of Rough-In Section is flush with the finished ceiling
surface. Tighten the Wing nuts.
RAB
Knock Out
.250
[6,35]
Butterfly
Bracket
Fig: 2
Wing Nut
NDIC4 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TRIM MODULE MOUNTING
1. Pull Male Connector conduit through frame opening.
Raise Trim Module towards opening and connect to
Female Connector conduit as shown in Fig. 3.
2. Press Torsion Springs inward and slide Trim Module
info frame opening. Release both springs into opening
together. Trim Ring should be flush to ceiling.
3. For the Wallwash Model, orient the fixture such that the
reflector is in correct orientation. Look for ‘Towards the
Wall’ label on the fixture.
WIRING
RISK OF FIRE. Universal voltage driver permits operation at
120V thru 277V, 50 or 60 Hz. For Non-Dimming, Electronic
Low Voltage (ELV) and Triac Dimming follow the wiring
directions in Fig. 4.
Rough-in
Section
Ceiling
Male Connector
Female
Connector
Trim Module
Torsion Spring
1. Connect the GROUND wire from fixture to supply ground.
2. Connect the black fixture lead to the (+) LINE supply lead.
3. Connect the white fixture lead to the (-) COMMON supply lead.
Trim Ring
10.462
[265,74
Fig: 3
]
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to
touch. Do not clean or maintain while fixture is energized.
Fig: 4
Lutron L3D Hi-Lume series drivers work with Lutron 3-Wire
Control (Fig. 5) or EcoSystem Digital Controls (Fig. 6).
Note: See www.lutron.com for complete instructions and functional
compatibility of Lutron drivers with Lutron or other control systems/
11.475
dimmers.
[291,47
]
1. Do not open fixture to clean the LED. Do not touch
the LED.
2. Do not touch reflector, lens, or trim cone.
3. Do not clean any fixture surface with wood base cleaning
material such as paper towels or tissues. Only use micro
fiber cleaning cloth.
TROUBLESHOOTING
1. Check that the line voltage at the fixture is correct. Refer
to wiring directions.
Fig: 5
2. Is the fixture grounded properly?
3. For questions on compatibility of dimmers purchased
separately refer to www.rabweb.com
Fig: 6
Easy Installation & Product Help
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
NDIC4 IN-1214
Tech Help Line
Call our experts 888 RAB-1000
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance. RAB cannot troubleshoot
Lutron systems and have provided only basic information. See
www.lutron.com for complete instructions and functional
compatibility of Lutron Drivers with Lutron or other Control systems/
dimmers.
rabweb.com
Visit our website for product info
10.462
[26
email 5,74]
Answered promptly sales@rabweb.com
6.232
[158,28
NDIC4 INSTALLATION INSTRUCTIONS
11.475
[291,47]
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
DIMENSIONAL DRAWING
4” Round
11.48”
10.462
[265,74]
10.46”
10.462
[265,74]
10.46”
5.5”
5.500
[139,7]
Cut-Out
Diameter: 5”
11.826
[300,38]
11.83”
11.826
[300,38]
4” Square
11.83”
10.462
[265,74]
10.46”
11.826
[300,38]
6.224
[158,09]
5.5”
422.6
]90,851[
005.5
]7,931[
264.01
]47,562[
10.46”
5.500
[139,7]
10.462
[265,74]
Cut-Out
Dimension: 5”x5”
6.23”
11.83”
6.232
[158,28]
6.23”
628.11
]83,003[
NDIC6 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
NDIC6R
Cut-Out Diameter: 7”
IMPORTANT
4
NDIC6S
Cut-Out: 7”x7”
3
2
REV
DATE
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS
FOR DESCRIPTION
FUTURE REFERENCE.
1
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable
local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY AD
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
4
3
4
2
3
REV
DESCRIPTION
2
DATE
1
MOUNTING BARS
D
D
D
C
C
C
C Channel-27”
Nailer Bar
13” adjustable to 24”
(provided with fixture)
C ChannelC-51”
(order Cat #: C-Chan 27)
Available upon request
13.375" REF
27.000
[685,8]
B
(order Cat #: C-Chan 51)
Available upon request
.500
[12,7]
B
Butterfly Brackets
ROUGH-IN MOUNTING
1. Nailer bars are provided for use with wood joist
installations. Insert through Nailer Bar Slots in
Butterfly Brackets and secure accordingly. C-Channels
are optionally available, consult factory. Consult local
building codes for final support of fixture.
(2)
QUOTATION DRAWING
11-14-12
RAB
.250
[6,35]
A
SCALE 0.500
1.500
[38,1]
.220
[5,59]
.220
[5,59]
.201
[5,11]
27.000
[685,8]
B
MATERIAL:
2. Remove appropriate Knock out on Junction box. Press
Clip to remove the Junction Box Cover.
3. Feed the supply wires through Knock out hole and
connect to the driver. Re-install Junction Box Cover. See
wiring section for details.
3
Nailer
Bar Slot
NOTES:
1. PART TO BE SUPPLIED BY TRIPAR INDUSTRIES
PART NUMBER 1287
2. MATERIAL: GALVANIZED STEEL
4
SCALE
A
Junction Box
Cover
REV DATE:
3-9-12
1/2
REV
PROPERTY
OF RAB LIGHTING, INCORPORATED
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
SHEET:
3
1
2
Clip
RAB
12.418
[315,43]
SCALE 0.500
SCALE 0.500
L I G H T I N G
170 LUDLOW AVE., NORTHVALE, NJ 07647
TITLE
Rough-in Section
13" NAILER BAR ASSEMBLY(Bottom
M & Fof the
Male Connector
Rough-in Section
MATERIAL:
Fig: 1
DRAWN BY: DH
A
PART No.:
SEE NOTES
15153
DRAWING NAME:
to be flush with
ceiling)
finished
15153 NAILER BAR
ASSY
DATE:
REV DATE:
3-9-12
SCALE
FULL
SHEET:
REV
1
SCALE 1.000
Butterfly
Bracket
MA
THIS
DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
15154-27
C-CHANNEL
QUOTATION DRAWING
4. The fixture can be adjusted to different heights above
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
the ceiling surface. ForPROPERTY
height adjustment,
loosen theINCORPORATED
OF RAB LIGHTING,
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
Wing Nut and slide the
Bracket.
If necessary
RAB Butterfly
LIGHTING, INC. IS STRICTLY
PROHIBITED.
RAB CONFIDENTIAL PATENT PENDING
4
3
2
remove the Wing Nut and insert in
screw in different
hole provided on the Butterfly Bracket. (Fig: 2)
RAB NDIC6 fixtures are IC rated allowing fixtures to be
completely covered with insulation and also comply with
13.91State
minimum Air Leakage requirements per the Washington
6
[353,47]
Energy Code and Model Energy Code.
DRAWN BY: DH
2
L
TIT
B
DRAWING NAME:
15154-27
DATE:
PROPERTY OF RAB LIGHTING, INCORPORATED
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
.250
[6,35]
27" C-CHANNEL
PART No.:
R
Knock Out
170 LUDLOW AVE., NORTHVALE, NJ 07647
22 GA EC STL
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
4
5. Adjust both the Butterfly Brackets such that the frame
of Rough-In Section is flush with the finished ceiling
surface. Tighten the Wing nuts.
.201
(2)
L I G H T I N G
[5,11]
TITLE
A
Fig: 2
Wing Nut
13.916
[353,4
7.516
DR
NDIC6 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TRIM MODULE MOUNTING
1. Pull Male Connector conduit through frame opening.
Raise Trim Module towards opening and connect to
Female Connector conduit as shown in Fig. 3.
2. Press Torsion Springs inward and slide Trim Module
info frame opening. Release both springs into opening
together. Trim Ring should be flush to ceiling.
3. For the Wallwash Model, orient the fixture such that the
reflector is in correct orientation. Look for ‘Towards the
Wall’ label on the fixture.
Rough-in
Section
Ceiling
WIRING
RISK OF FIRE. Universal voltage driver permits operation at
120V thru 277V, 50 or 60 Hz. For Non-Dimming, Electronic
Low Voltage (ELV) and Triac Dimming follow the wiring
directions in Fig. 4.
1. Connect the GROUND wire from fixture to supply ground.
2. Connect the black fixture lead to the (+) LINE supply lead.
3. Connect the white fixture lead to the (-) COMMON supply lead.
Male Connector
Female
Connector
Trim Module
Torsion Spring
Trim Ring
Fig: 3
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to
touch. Do not clean or maintain while fixture is energized.
Fig: 4
Lutron L3D Hi-Lume series drivers work with Lutron 3-Wire
Control (Fig. 5) or EcoSystem Digital Controls (Fig. 6).
Note: See www.lutron.com for complete instructions and
functional
13.9
16
compatibility of Lutron drivers with Lutron or other control
systems/
[353,4
7]
dimmers.
1. Do not open fixture to clean the LED. Do not touch
the LED.
2. Do not touch reflector, lens, or trim cone.
3. Do not clean any fixture surface with wood base cleaning
material such as paper towels or tissues. Only use micro
fiber cleaning cloth.
TROUBLESHOOTING
13.916
[353,47]
1. Check that the line voltage at the fixture is correct. Refer
to wiring directions.
Fig: 5
2. Is the fixture grounded properly?
3. For questions on compatibility of dimmers purchased
separately refer to www.rabweb.com
Fig: 6
Easy Installation & Product Help
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
NDIC6 IN-1214
Tech Help Line
Call our experts 888 RAB-1000
Note: These instructions do not cover all details or variations in
12.418
equipment
nor do they provide for every possible situation during
[315,43]
installation, operation or maintenance. RAB cannot troubleshoot
Lutron systems and have provided only basic information. See
www.lutron.com for complete instructions and functional
compatibility of Lutron Drivers with Lutron or other Control systems/
dimmers.
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
7
[
NDIC6 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
NDIC6R
13.916
[353,47]
DIMENSIONAL DRAWING
13.92”
12.418
[315,43]
12.42”
242.6
]55,851[
13.916
[353,47]
6.24”
12.418
[315,43]
7.516
[190,91]
Cut-Out
Diameter: 7”
814.21
]34,513[
615.7
]19,091[
7.52”
12.42”
6.242
[158,55]
619.31
]74,353[
13.92”
13.826
[351,18]
13.83”
NDIC6S
12.631
[320,82]
12..63”
814.21
]34,513[
13.826
[351,18]
032.6
]32,851[
032.6
]32,851[
619.31
7.515
]74,353[
[190,88]
12.631
[320,82]
6.23”
628.31
]81,153[
136.21
]28,023[
13.83”
12.63”
515.7
]88,091[
7.52”
628.31
]81,153[
136.21
]28,023[
515.7
]88,091[
6.230
[158,23]
Cut-Out
Dimension: 7”x7”
NDIC4 EMERGENCY BATTERY BACKUP
INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
NDIC4R/E2
Cut-Out Diameter: 5”
NDIC4S/E2
Cut-Out: 5”x5”
IMPORTANT
SUITABLE FOR INSTALLATION IN NON-ACCESSIBLE CEILINGS ONLY.
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
THIS IS AN EMERGENCY BATTERY BACKUP FIXTURE THAT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE
BATTERY MUST BE RECYCLED OR DISPOSED OFF PROPERLY.
SAFETY INSTRUCTIONS
4
3
2
WARNING:
Make certain power is OFF
before installing or maintaining
fixture. No user serviceable parts inside.
REV
DESCRIPTION
DATE
WARNING: Suitable for wet locations where the ambient temperature is 0° C minimum,
+40° C
maximum.
1
WARNING: Suitable for installation in Insulated Ceilings only.
D
4
3
4
2
3
REV
DESCRIPTION
2
DATE
1
MOUNTING BARS
D
D
D
C
C
C
C Channel-27”
Nailer Bar
13” adjustable to 24”
(provided with fixture)
C ChannelC-51”
(order Cat #: C-Chan 27)
Available upon request
13.375" REF
27.000
[685,8]
B
OPERATION
(order Cat #: C-Chan 51)
Available upon request
.500
[12,7]
B
27.000
[685,8]
B
SCALE 0.500
1.500
[38,1]
.220
[5,59]
.220
[5,59]
QUOTATION DRAWING
11-14-12
1. When AC power is applied, the charging indicator light is illuminated, indicating that the battery is being charged.
RAB
B
2. When power fails, the emergency ballast automatically switches to emergency power (internal battery),
operating at reduced
27" C-CHANNEL
illumination. The emergency ballast supplies 7W of power (measured at nominal battery voltage) at a maximum rated current
PROPERTY OF RAB LIGHTING, INCORPORATED
PROPERTY
OF RAB
LIGHTING,
INCORPORATED
of 270mA with a maximum voltage of 50VDC in emergency
mode
for
a minimum
of 90 minutes.
3. When AC power is restored, the emergency ballast automatically returns to charging mode.
.201
[5,11]
(2)
.250
[6,35]
A
.201
(2)
L I G H T I N G
[5,11]
TITLE
A
170 LUDLOW AVE., NORTHVALE, NJ 07647
.250
[6,35]
A
MATERIAL:
15154-27
DATE:
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
4
PART No.:
22 GA EC STL
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
3
DRAWN BY: DH
2
4
SCALE
DRAWING NAME:
REV
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
SHEET:
1
3
2
QUOTATION DRAWING
RAB
RAB NDIC4 fixtures are IC rated allowing
NOTES: fixtures to be completely covered with insulation and also comply with minimum Air Leakage
1. PART TO BE SUPPLIED BY TRIPAR INDUSTRIES
L I G H T I N G
170 LUDLOW AVE., NORTHVALE, NJ 07647
requirements per the Washington State
Energy1287
Code and Model Energy Code.
PART NUMBER
TITLE
SCALE 0.500
2. MATERIAL: GALVANIZED STEEL
13" NAILER BAR ASSEMBLY M & F
MATERIAL:
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
PART No.:
SEE NOTES
15153
DATE:
MA
THIS
DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
15154-27
C-CHANNEL
REV DATE:
3-9-12
1/2
R
L
TIT
DRAWING NAME:
15153 NAILER BAR ASSY
REV DATE:
REV
A
SCALE 0.500
DR
NDIC4 EMERGENCY BATTERY BACKUP
INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
ROUGH-IN MOUNTING
Knock Out
Junction Box
Cover
Butterfly Brackets
1. Nailer bars are provided for use with wood joist
installations. Insert through Nailer Bar Slots in
Butterfly Brackets and secure accordingly. C-Channels
are optionally available, consult factory. Consult local
building codes for final support of fixture.
Fig. 1
Clip
2. Remove appropriate Knock out on Junction box. Press
Clip to remove the Junction Box Cover.
3. Feed the supply wires through Knock out hole and
connect to the driver. Re-install Junction Box Cover. See
wiring section for details.
Rough-in Section
(Bottom of the Rough-in
Section to be flush with
finished ceiling)
Nailer Bar Slot
4. The fixture can be adjusted to different heights above
the ceiling surface. For height adjustment, loosen the
Wing Nut and slide the Butterfly Bracket. If necessary
remove the Wing Nut and insert in screw in different
hole provided on the Butterfly Bracket. (Fig: 2)
Male Connector
Fig. 2
5. Adjust both the Butterfly Brackets such that the frame
of Rough-In Section is flush with the finished ceiling
surface. Tighten the Wing nuts.
TRIM MODULE MOUNTING
1. Pull Male Connector conduit through frame opening.
Raise Trim Module towards opening and connect to
Female Connector conduit as shown in Fig. 3.
Wing Nut
Butterfly
Bracket
2. Press Torsion Springs inward and slide Trim Module
info frame opening. Release both springs into opening
together. Trim Ring should be flush to ceiling.
3. For the Wallwash Model, orient the fixture such that the
reflector is in correct orientation. Look for ‘Towards the
Wall’ label on the fixture.
Fig. 3
Rough-in Section
Ceiling
Male Connector
Trim Module
Female Connector
Torsion Spring
Trim Ring
NDIC4 EMERGENCY BATTERY BACKUP
INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
WIRING
TROUBLESHOOTING
CAUTION: THIS IS AN EMERGENCY BATTERY BACKUP
FIXTURE. Voltage could be present in Battery. To prevent
high voltage from being present on output leads, inverter
connector must be open. Do not join inverter connector
until installation is complete and AC power is supplied to
the emergency ballast.
1. Check that the line voltage at the fixture is correct. Refer
to wiring directions.
NOTE: Make sure that the necessary branch circuit wiring is
available. An unswitched AC source of power is required. The
emergency ballast must be fed from the same branch circuit
as the AC ballast.
4. If the LED is blinking the fixture may be overheating.
Remove the Trim assembly and if the fixture is labeled
‘BLINKING LIGHT OF THIS THERMALLY PROTECTED
LUMINAIRE MAY INDICATE OVERHEATING’ allow the
fixture to cool down. Determine cause of overheating
and remove. Fixtures with this label have a thermal
protector that turns fixture off above a certain
temperature. It will automatically restart when cool.
Do not use any supply voltage other than those specified
below.
NDIC4R/E2 or NDIC4S/E2 120V-277V, 50/60Hz
1. Connect the UNSWITCHED black fixture lead to the HOT
supply lead.
2. Connect red and black lead together, if not using a
switching method.
3. If switching, connect SWITCHED red lead to a switch.
4. Connect the COMMON fixture lead to the COMMON
supply lead.
5.For Lutron system, follow manufacturer’s instructions.
5. Connect the GROUND wire from fixture to supply ground.
Do NOT connect the GROUND of the dimming fixture to
the output.
6. All unused leads must be capped and insulated.
7. After installation is complete, supply AC power to the
emergency ballast and join the inverter connector.
9. At this point, power should be connected to both the
AC ballast and the emergency ballast, and the Charging
Indicator Light should illuminate indicating the battery is
charging.
10. A short-term discharge test may be conducted after the
emergency ballast has been charging for one hour. Charge
for 24 hours before conducting a long-term discharge test.
Refer to OPERATION.
2. Is the fixture grounded properly?
3. For questions on compatibility of dimmers purchased
separately refer to www.rabweb.com
CLEANING
CAUTION: Be sure fixture temperature is cool enough to
touch. Do not clean or maintain while fixture is energized.
1. Do not open fixture to clean the LEDs. Do not touch the
LEDs.
2. Do not touch reflector, lens, or trim cone.
3. Do not clean any fixture surface with wood base cleaning
material such as paper towels or tissues. Only use micro
fiber cleaning cloth.
MAINTENANCE
Although no routine maintenance is required to keep
the emergency ballast functional, it should be checked
periodically to ensure that it is working. The following
schedule is recommended:
1. Visually inspect the charging indicator light monthly. It
should be illuminated.
2. Test the emergency operation of the fixture at 30-day
intervals for a minimum of 30 seconds.
3. Conduct a 90-minute discharge test once a year. Fixture
would operate at reduced illumination for a minimum of
90 minutes.
To reduce the risk of electric shock, disconnect both normal and emergency power supplies and converter connector of the emergency ballast before
servicing. Do not attempt to service the emergency ballast. The use of accessory equipment may cause an unsafe condition. Do not use this product for
other than intended use. Refer any servicing indicated by these checks to a Qualified Service Personnel.
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during installation, operation or maintenance. RAB cannot troubleshoot Lutron systems
and have provided only basic information. See www.lutron.com for complete instructions and functional compatibility of Lutron Drivers with Lutron or
other Control systems/dimmers.
Easy Installation & Product Help
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
NDIC4 EM IN 1115
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
NDIC4 EMERGENCY BATTERY BACKUP
INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
DIMENSIONAL DRAWING
13.39”
4” Round
7.07”
13.06”
6.12”
Ø 5.50”
13.39”
7.07”
4” Square
12.94”
6.12”
Ø 5.50”
RED
WHITE
Northvale, New Jersey 07647 USA
©2012 RAB LIGHTING Inc.
NDIC4 EM IN 1115
BROWN
BROWN
VIOLET
VIOLET
BLACK
YELLOW
BLUE
BLACK
RED
YELLOW
Tech Help Line
Call our experts 888 RAB-1000
WHITE
WHITE
RED +
BLUE OR
BLACK -
BLACK
RED
8" Flex Conduit Whip
LED TRIM MODULE
-
BLACK
email
Answered promptly sales@rabweb.com
SWITCH PLATE WITH
INTEGRAL TEST
SWITCH (INCLUDED)
SWITCH BOX
(BY OTHERS)
YELLOW - BLACK STRIPE
ELECTRONIC
BLOCK
PROTECTOR
JUNCTION BOX
BLUE
rabweb.com
Visit our website for product info
Easy Installation & Product Help
CUSTOMER SHOULD
CONNECT ONLY
AFTER FINISHING
WIRING TO AC
POWER. BATTERY
COULD HAVE
CHARGE & SHOCK.
INVERTER
CONNECTOR:
CONNECT ONLY AFTER
AC SUPPLY POWER IS
CONNECTED
RAB LABEL - ADD
2' Flex Conduit Whip
ORANGE
- BLACK
STRIPE
WHITE
- RED
STRIPE
EMERGENCY
LED DRIVER
BSL17C-C2
BODINE
YELLOW - BLACK STRIPE
WHITE
WHITE - BLACK STRIPE
LED DRIVER
120V - 277V
Emergency Ballast and AC Ballast must be fed from the same circuit
WIRING DIAGRAM for EMERGENCY OPERATION at 120V - 277V
+
RAB LABEL ADD
BLACK
RAB LABEL ADD
IF NOT SWITCHED, THEN
CAP TOGETHER
JUNCTION
BOX
CONNECT TO
MAIN POWER
UNSWITCHED
SWITCHED
COMMON
GROUND
WHITE
Northvale, New Jersey 07647 USA
BROWN
BROWN
VIOLET
VIOLET
BLACK
YELLOW
BLUE
BLACK
RED
Tech Help Line
Call our experts 888 RAB-1000
YELLOW
TP
WHITE
BLACK
WHITE
RED +
BLUE OR
BLACK -
BLACK
RED
8" Flex Conduit Whip
LED TRIM MODULE
-
BLACK
email
Answered promptly sales@rabweb.com
SWITCH PLATE WITH
INTEGRAL TEST
SWITCH (INCLUDED)
SWITCH BOX
(BY OTHERS)
YELLOW - BLACK STRIPE
ELECTRONIC
BLOCK
PROTECTOR
JUNCTION BOX
BLUE
rabweb.com
Visit our website for product info
Easy Installation & Product Help
CUSTOMER SHOULD
CONNECT ONLY
AFTER FINISHING
WIRING TO AC
POWER. BATTERY
COULD HAVE
CHARGE & SHOCK.
INVERTER
CONNECTOR:
CONNECT ONLY AFTER
AC SUPPLY POWER IS
CONNECTED
©2012 RAB LIGHTING Inc.
NDIC4 EM IN 1115
RED
RAB LABEL - ADD
2' Flex Conduit Whip
ORANGE
- BLACK
STRIPE
WHITE
- RED
STRIPE
EMERGENCY
LED DRIVER
BSL17C-C2
BODINE
YELLOW - BLACK STRIPE
WHITE
WHITE - BLACK STRIPE
BLACK
LED DRIVER
120V - 277V
Emergency Ballast and AC Ballast must be fed from the same circuit
TP
CONNECT TO
MAIN POWER
UNSWITCHED
SWITCHED
COMMON
GROUND
Thermal Protector
RAB LABEL ADD
BLACK
RAB LABEL ADD
IF NOT SWITCHED, THEN
CAP TOGETHER
JUNCTION
BOX
WIRING DIAGRAM for EMERGENCY OPERATION at 120V - 277V with Thermal Protector
+
NDIC6 EMERGENCY BATTERY BACKUP
INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
NDIC6R/E2
Cut-Out Diameter: 7”
NDIC6S/E2
Cut-Out: 7” x7”
IMPORTANT
SUITABLE FOR INSTALLATION IN NON-ACCESSIBLE CEILINGS ONLY.
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
THIS IS AN EMERGENCY BATTERY BACKUP FIXTURE THAT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE
BATTERY MUST BE RECYCLED OR DISPOSED OFF PROPERLY.
SAFETY INSTRUCTIONS
4
3
2
WARNING:
Make certain power is OFF
before installing or maintaining
fixture. No user serviceable parts inside.
REV
DESCRIPTION
DATE
WARNING: Suitable for wet locations where the ambient temperature is 0° C minimum,
+40° C
maximum.
1
WARNING: Suitable for installation in Insulated Ceilings only.
D
4
3
4
2
3
REV
DESCRIPTION
2
DATE
1
MOUNTING BARS
D
D
D
C
C
C
C Channel-27”
Nailer Bar
13” adjustable to 24”
(provided with fixture)
C ChannelC-51”
(order Cat #: C-Chan 27)
Available upon request
13.375" REF
27.000
[685,8]
B
OPERATION
(order Cat #: C-Chan 51)
Available upon request
.500
[12,7]
B
27.000
[685,8]
B
SCALE 0.500
1.500
[38,1]
.220
[5,59]
.220
[5,59]
QUOTATION DRAWING
11-14-12
1. When AC power is applied, the charging indicator light is illuminated, indicating that the battery is being charged.
RAB
B
2. When power fails, the emergency ballast automatically switches to emergency power (internal battery),
operating at reduced
27" C-CHANNEL
illumination. The emergency ballast supplies 7W of power (measured at nominal battery voltage) at a maximum rated current
PROPERTY OF RAB LIGHTING, INCORPORATED
PROPERTY
OF RAB
LIGHTING,
INCORPORATED
of 270mA with a maximum voltage of 50VDC in emergency
mode
for
a minimum
of 90 minutes.
3. When AC power is restored, the emergency ballast automatically returns to charging mode.
.201
[5,11]
(2)
.250
[6,35]
A
.201
(2)
L I G H T I N G
[5,11]
TITLE
A
170 LUDLOW AVE., NORTHVALE, NJ 07647
.250
[6,35]
A
MATERIAL:
15154-27
DATE:
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
4
PART No.:
22 GA EC STL
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
3
DRAWN BY: DH
2
4
SCALE
DRAWING NAME:
REV
ANY REPRODUCTION OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF
RAB LIGHTING, INC. IS STRICTLY PROHIBITED. RAB CONFIDENTIAL PATENT PENDING
SHEET:
1
3
2
QUOTATION DRAWING
RAB
RAB NDIC6 fixtures are IC rated allowing
NOTES: fixtures to be completely covered with insulation and also comply with minimum Air Leakage
1. PART TO BE SUPPLIED BY TRIPAR INDUSTRIES
L I G H T I N G
170 LUDLOW AVE., NORTHVALE, NJ 07647
requirements per the Washington State
Energy1287
Code and Model Energy Code.
PART NUMBER
TITLE
SCALE 0.500
2. MATERIAL: GALVANIZED STEEL
13" NAILER BAR ASSEMBLY M & F
MATERIAL:
THIS DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
PART No.:
SEE NOTES
15153
DATE:
MA
THIS
DRAWING AND THE INFORMATION IT DISCLOSES IS THE EXCLUSIVE
15154-27
C-CHANNEL
REV DATE:
3-9-12
1/2
R
L
TIT
DRAWING NAME:
15153 NAILER BAR ASSY
REV DATE:
REV
A
SCALE 0.500
DR
NDIC6 EMERGENCY BATTERY BACKUP
INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
ROUGH-IN MOUNTING
1. Nailer bars are provided for use with wood joist
installations. Insert through Nailer Bar Slots in
Butterfly Brackets and secure accordingly. C-Channels
are optionally available, consult factory. Consult local
building codes for final support of fixture.
Fig. 1
Butterfly Brackets
Knock Out
Junction Box
Cover
Clip
2. Remove appropriate Knock out on Junction box. Press
Clip to remove the Junction Box Cover.
3. Feed the supply wires through Knock out hole and
connect to the driver. Re-install Junction Box Cover. See
wiring section for details.
Nailer Bar Slot
Male Connector
4. The fixture can be adjusted to different heights above
the ceiling surface. For height adjustment, loosen the
Wing Nut and slide the Butterfly Bracket. If necessary
remove the Wing Nut and insert in screw in different
hole provided on the Butterfly Bracket. (Fig: 2)
Rough-in Section
(Bottom of the Rough-in
Section to be flush with
finished ceiling)
Fig. 2
5. Adjust both the Butterfly Brackets such that the frame
of Rough-In Section is flush with the finished ceiling
surface. Tighten the Wing nuts.
TRIM MODULE MOUNTING
1. Pull Male Connector conduit through frame opening.
Raise Trim Module towards opening and connect to
Female Connector conduit as shown in Fig. 3.
Wing Nut
Butterfly
Bracket
2. Press Torsion Springs inward and slide Trim Module
info frame opening. Release both springs into opening
together. Trim Ring should be flush to ceiling.
3. For the Wallwash Model, orient the fixture such that the
reflector is in correct orientation. Look for ‘Towards the
Wall’ label on the fixture.
Fig. 3
Rough-in Section
Ceiling
Male Connector
Female Connector
Torsion Spring
Trim Module
Trim Ring
NDIC6 EMERGENCY BATTERY BACKUP
INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
WIRING
TROUBLESHOOTING
CAUTION: THIS IS AN EMERGENCY BATTERY BACKUP
FIXTURE. Voltage could be present in Battery. To prevent
high voltage from being present on output leads, inverter
connector must be open. Do not join inverter connector
until installation is complete and AC power is supplied to
the emergency ballast.
1. Check that the line voltage at the fixture is correct. Refer
to wiring directions.
NOTE: Make sure that the necessary branch circuit wiring is
available. An unswitched AC source of power is required. The
emergency ballast must be fed from the same branch circuit
as the AC ballast.
4. If the LED is blinking the fixture may be overheating.
Remove the Trim assembly and if the fixture is labeled
‘BLINKING LIGHT OF THIS THERMALLY PROTECTED
LUMINAIRE MAY INDICATE OVERHEATING’ allow the
fixture to cool down. Determine cause of overheating
and remove. Fixtures with this label have a thermal
protector that turns fixture off above a certain
temperature. It will automatically restart when cool.
Do not use any supply voltage other than those specified
below.
NDIC6R/E2 or NDIC6S/E2 120V-277V, 50/60Hz
1. Connect the UNSWITCHED black fixture lead to the HOT
supply lead.
2. Connect red and black lead together, if not using a
switching method.
3. If switching, connect SWITCHED red lead to a switch.
4. Connect the COMMON fixture lead to the COMMON
supply lead.
5.For Lutron system, follow manufacturer’s instructions.
5. Connect the GROUND wire from fixture to supply ground.
Do NOT connect the GROUND of the dimming fixture to
the output.
6. All unused leads must be capped and insulated.
7. After installation is complete, supply AC power to the
emergency ballast and join the inverter connector.
9. At this point, power should be connected to both the
AC ballast and the emergency ballast, and the Charging
Indicator Light should illuminate indicating the battery is
charging.
10. A short-term discharge test may be conducted after the
emergency ballast has been charging for one hour. Charge
for 24 hours before conducting a long-term discharge test.
Refer to OPERATION.
2. Is the fixture grounded properly?
3. For questions on compatibility of dimmers purchased
separately refer to www.rabweb.com
CLEANING
CAUTION: Be sure fixture temperature is cool enough to
touch. Do not clean or maintain while fixture is energized.
1. Do not open fixture to clean the LEDs. Do not touch the
LEDs.
2. Do not touch reflector, lens, or trim cone.
3. Do not clean any fixture surface with wood base cleaning
material such as paper towels or tissues. Only use micro
fiber cleaning cloth.
MAINTENANCE
Although no routine maintenance is required to keep
the emergency ballast functional, it should be checked
periodically to ensure that it is working. The following
schedule is recommended:
1. Visually inspect the charging indicator light monthly. It
should be illuminated.
2. Test the emergency operation of the fixture at 30-day
intervals for a minimum of 30 seconds.
3. Conduct a 90-minute discharge test once a year. Fixture
would operate at reduced illumination for a minimum of
90 minutes.
To reduce the risk of electric shock, disconnect both normal and emergency power supplies and converter connector of the emergency ballast before
servicing. Do not attempt to service the emergency ballast. The use of accessory equipment may cause an unsafe condition. Do not use this product for
other than intended use. Refer any servicing indicated by these checks to a Qualified Service Personnel.
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during installation, operation or maintenance. RAB cannot troubleshoot Lutron systems
and have provided only basic information. See www.lutron.com for complete instructions and functional compatibility of Lutron Drivers with Lutron or
other Control systems/dimmers.
Easy Installation & Product Help
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
NDIC4 EM IN 1115
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
NDIC6 EMERGENCY BATTERY BACKUP
INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
DIMENSIONAL DRAWING
6” Round
15.452
[392,48]
8.110
[205,99]
13
[330]
6.125
[155,56]
6” Square
15.362
[390,19]
8.065
[204,85]
13
[330]
6.125
[155,56]
RED
WHITE
Northvale, New Jersey 07647 USA
©2012 RAB LIGHTING Inc.
NDIC46 EM IN 1215
BROWN
BROWN
VIOLET
VIOLET
BLACK
YELLOW
BLUE
BLACK
RED
YELLOW
Tech Help Line
Call our experts 888 RAB-1000
WHITE
WHITE
RED +
BLUE OR
BLACK -
BLACK
RED
8" Flex Conduit Whip
LED TRIM MODULE
-
BLACK
email
Answered promptly sales@rabweb.com
SWITCH PLATE WITH
INTEGRAL TEST
SWITCH (INCLUDED)
SWITCH BOX
(BY OTHERS)
YELLOW - BLACK STRIPE
ELECTRONIC
BLOCK
PROTECTOR
JUNCTION BOX
BLUE
rabweb.com
Visit our website for product info
Easy Installation & Product Help
CUSTOMER SHOULD
CONNECT ONLY
AFTER FINISHING
WIRING TO AC
POWER. BATTERY
COULD HAVE
CHARGE & SHOCK.
INVERTER
CONNECTOR:
CONNECT ONLY AFTER
AC SUPPLY POWER IS
CONNECTED
RAB LABEL - ADD
2' Flex Conduit Whip
ORANGE
- BLACK
STRIPE
WHITE
- RED
STRIPE
EMERGENCY
LED DRIVER
BSL17C-C2
BODINE
YELLOW - BLACK STRIPE
WHITE
WHITE - BLACK STRIPE
LED DRIVER
120V - 277V
Emergency Ballast and AC Ballast must be fed from the same circuit
WIRING DIAGRAM for EMERGENCY OPERATION at 120V - 277V
+
RAB LABEL ADD
BLACK
RAB LABEL ADD
IF NOT SWITCHED, THEN
CAP TOGETHER
JUNCTION
BOX
CONNECT TO
MAIN POWER
UNSWITCHED
SWITCHED
COMMON
GROUND
WHITE
Northvale, New Jersey 07647 USA
BROWN
BROWN
VIOLET
VIOLET
BLACK
YELLOW
BLUE
BLACK
RED
Tech Help Line
Call our experts 888 RAB-1000
YELLOW
TP
WHITE
BLACK
WHITE
RED +
BLUE OR
BLACK -
BLACK
RED
8" Flex Conduit Whip
LED TRIM MODULE
-
BLACK
email
Answered promptly sales@rabweb.com
SWITCH PLATE WITH
INTEGRAL TEST
SWITCH (INCLUDED)
SWITCH BOX
(BY OTHERS)
YELLOW - BLACK STRIPE
ELECTRONIC
BLOCK
PROTECTOR
JUNCTION BOX
BLUE
rabweb.com
Visit our website for product info
Easy Installation & Product Help
CUSTOMER SHOULD
CONNECT ONLY
AFTER FINISHING
WIRING TO AC
POWER. BATTERY
COULD HAVE
CHARGE & SHOCK.
INVERTER
CONNECTOR:
CONNECT ONLY AFTER
AC SUPPLY POWER IS
CONNECTED
©2012 RAB LIGHTING Inc.
NDIC6 EM IN 1215
RED
RAB LABEL - ADD
2' Flex Conduit Whip
ORANGE
- BLACK
STRIPE
WHITE
- RED
STRIPE
EMERGENCY
LED DRIVER
BSL17C-C2
BODINE
YELLOW - BLACK STRIPE
WHITE
WHITE - BLACK STRIPE
BLACK
LED DRIVER
120V - 277V
Emergency Ballast and AC Ballast must be fed from the same circuit
TP
CONNECT TO
MAIN POWER
UNSWITCHED
SWITCHED
COMMON
GROUND
Thermal Protector
RAB LABEL ADD
BLACK
RAB LABEL ADD
IF NOT SWITCHED, THEN
CAP TOGETHER
JUNCTION
BOX
WIRING DIAGRAM for EMERGENCY OPERATION at 120V - 277V with Thermal Protector
+